These particular values are not configurable and today we always set
CONFIG_SECURE_BL1_ONLY. Move these to where they're used in the code,
and drop from the CONFIG namespace.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Remove some code, primarily CPM2 related, that is now unused since the
removal of MPC8540/60ADS.
Fixes 3913191c8a ("powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().
Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The BOOT_TARGET_DEVICES list for distro_bootcmd was hard-coded to assume
that all boot devices are available/enabled in the configuration,
thus ignoring the actual config settings. The config_distro_bootcmd.h
header file specifically has compile-time checks to detect such problems.
To allow disabling USB, SCSI, etc. in custom lx2160a board configs,
make it depend on the config settings and use only the enabled features.
Signed-off-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Use the complete 512kb (4 blocks) nand partition reserved for u-boot
environment instead of just the first block, this allows the module to
have a working environment even if 3 blocks are bad.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Now that single defconfig can be used for booting J721E EVM and
SK, default device tree will not work for selecting dtb for
kernel. Update the findfdt env to select right dtb based on
board_name env variable.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
There are no boards that define CONFIG_SYS_RESET_ADDR, so drop the
remaining comments referencing it and also the config_whitelist.txt entry.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: thomas@wytron.com.tw
This driver adds support for the keyboard on Apple Silicon laptops.
The controller for this keyboard sits on an SPI bus and uses an
Apple-specific HID over SPI protocol. The packets sent by this
controller for key presses and key releases are fairly simple and
are decoded directly by the code in this driver and converted into
standard Linux keycodes. The same controller handles the touchpad
found on these laptops. Packets for touchpad events are simply
ignored.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert
to Driver Model and use uclass mvgbe and the compatible driver M88E1118R
to bring up Ethernet.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- As the result of the migration to Driver Model, this u-boot image has
grown substantially (about 100K, give or take). The old envs location
at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K).
- Miscellaneous changes: Move constants to .c file and remove header file
board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to
keep u-boot image under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Dockstar board has the network chip Marvell 88E1116R. Convert to
Ethernet driver model, and use uclass mvgbe and the compatible driver
M88E1118R to bring up Ethernet.
- Add CONFIG_DM_ETH and associated configs.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Add CONFIG_PHY_MARVELL to properly configure the network.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Miscellaneous changes: Move constants to .c file and remove
header file board/Seagate/dockstar/dockstar.h, use
CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, add CONFIG_HUSH_PARSER, use BIT macro, and cleanup comments.
- Note: This patch is a RESEND for a previous patch:
https://patchwork.ozlabs.org/project/uboot/patch/20210812051854.1340-2-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Miscellaneous changes: Move constants to .c file and remove header file
board/iomega/iconnect/iconnect.h. Add CONFIG_HUSH_PARSER, use BIT macro,
and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Globalscale Technologies Dreamplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network
port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned,
could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/dreamplug/dreamplug.h, cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE
Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is defined based on two other CONFIGs for all boards except sandbox
and durian.
For sandbox the value does not matter. For durian the value seems
excessive.
Drop the option completely, to simplify configuration and reduce the
number of things we need to convert to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_IDE_MAXBUS
CONFIG_SYS_IDE_MAXDEVICE
CONFIG_SYS_ATA_BASE_ADDR
CONFIG_SYS_ATA_STRIDE
CONFIG_SYS_ATA_DATA_OFFSET
CONFIG_SYS_ATA_REG_OFFSET
CONFIG_SYS_ATA_ALT_OFFSET
CONFIG_SYS_ATA_IDE0_OFFSET
CONFIG_SYS_ATA_IDE1_OFFSET
CONFIG_ATAPI
CONFIG_IDE_RESET
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move setting the default boot command to the
apalis/colibri_imx6_defconfig. It allows replacing the command
without code modification.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The Linux Kernel Image size for arm64 is still growing.
A Kernel with 54 MB at load address 0x80280000 overlaps
with fdt_addr at 0x83000000. So let's increase it to 0x84000000
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Commit 72d81360aa ("global: Convert CONFIG_LOADADDR to
CONFIG_SYS_LOADADDR") dropped the usage of LOADADDR and replaced it with
SYS_LOADADDR.
Use the correct macro in environment by replacing CONFIG_LOADADDR with
CONFIG_SYS_LOADADDR.
Fixes: d75ebf3482 ("imx: ventana: fix splash logo drawing")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Add fdt_addr_r fdtfile which used by distro boot, and cleanup legacy
environment variables.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
We changed to single flash.bin now. So dfu_alt_info should be modified
to reflect this change.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The PDK2 board is capable of running both 100M and 1G ethernet. However,
the i.MX6 has only one ethernet MAC, so it is possible to configure
either 100M or 1G Ethernet. In case of 100M option, the PHY is on the
SoM and the signals are routed to a RJ45 port. For 1G the PHY is on
the PDK2 board with another RJ45 port. 100M and 1G ethernet use
different signal pins from the i.MX6, but share the MDIO bus.
This SoM board combination is used to demonstrate how to enable 1G
ethernet configuration.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Use the complete 512kb (4 blocks) nand partition reserved for u-boot
environment instead of just the first block, this allows the module
to have a working environment even if 3 blocks are bad.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Adds support for SUNIV and the F1C100s.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Remove some pointless #ifdefs from this file, as there are quite too
many of them already.
Some definitions don't really hurt to have in any case, so remove the
pointless CONFIG_MMC guard around CONFIG_MMC_SUNXI_SLOT.
The BOARD_SIZE_LIMIT applies regardless of ARM64 or not (now), so remove
that guard as well. The maximum number of MMC devices does not depend on
CONFIG_ENV_IS_IN_MMC, so move that out to simplify the file.
Last but not least CONFIG_SPL_BOARD_LOAD_IMAGE serves no real purpose
anymore: it's unconditionally defined for all sunxi boards, and protects
nothing applicable outside of sunxi code anymore. Just remove it.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Field fail-safe u-boot update procedure for pg-wcom boards is defined and
implemented by patch: 59b3403.
This patch invokes the update procedure for pg-wcom-ls102x designs during
early misc_init_f execution.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The GoFlex Home board has the network chip Marvell 88E1116R.
Use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: use CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
With Ethboot support in SPL, network stack requires more BSS area, so
increase BSS max size to 16K
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Today the bootcount is not managed by the Linux kernel for STM32MP15 as
we don't have driver to update the used backup register in TAMP and the
recovery command still executes the normal bootcmd with
'altbootcmd=run bootcmd'.
So the bootcount feature is never used, the config CONFIG_BOOTCOUNT_LIMIT
and the associated environment variable 'altbootcmd' can be removed to
reduce the U-Boot size.
Each boards can re-enable this feature later in their defconfig, if it is
needed, with the expected backend, for example CONFIG_BOOTCOUNT_GENERIC
or CONFIG_BOOTCOUNT_ENV.
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the following to Kconfig:
CONFIG_AT91_EFLASH
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Prepare migration to Kconfig.
CONFIG_SYS_MAX_FLASH_BANKS_DETECT becomes boolean and
CONFIG_SYS_MAX_FLASH_BANKS define the MAX size, also used
for detection when CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
(CFI_MAX_FLASH_BANKS = CONFIG_SYS_MAX_FLASH_BANKS).
CONFIG_SYS_MAX_FLASH_BANKS become mandatory when
CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
The am335x-ice-v2 board's Ethernet ports can be configured
in 'MII' or 'RMII' mode to be connected to 'PRUSS' or 'CPSW'
Ethernet subsystems.
This patch sets the environment variable 'ice_mii' to
'mii' or 'rmii' accordingly. Based on that we choose the
appropriate board devicetree i.e. 'am335x-ice-v2.dtb' or
'am335x-ice-v2-prueth.dtb'.
Since there are 2 Ethernet ports with 2 modes, there can be 4
configurations but for now we consider both ports in different modes
to be an invalid configuration and prevent boot in that case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Amjad: use overlay instead of using new am335x-ice-v2-prueth.dtb]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make prueth_is_mii be marked __maybe_unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
BOOT_TARGET_DEVICES should only be added if the corresponding u-boot
command is enabled otherwise the build will fail.
Signed-off-by: Piotr Kubik <piotr_kubik@vp.pl>
These hardcoded values were calculated from CONFIG_SPL_TEXT_BASE macro. Now
this macro is configurable via Kconfig, so calculate values 0x0030/0x4030
at compile time via CONFIG_SPL_TEXT_BASE option. Values 0x0030/0x4030
represents offset of CONFIG_SPL_TEXT_BASE from address 0x40000000.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Memory layout in the comment is from Armada XP platform which uses load
address 0x40004030. DB-88f6720 is Armada 375 platform which uses same load
address as Armada 38x which is 0x40000030.
Currently SPL support for Armada 375 is unfinished and does not work. There
is missing Serdes initialization and DDR3 training code. So nobody noticed
that CONFIG_SPL_* options are not correct.
Fix at least CONFIG_SPL_TEXT_BASE constant and remove incorrect comments
about memory layout. So it is not misleading.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
After the conversion to DM the SD card shows up as 'mmc 2'
device.
Adjust the 'mmcdev' and the distro command 'func' accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Enable support for USB and USB storage on the UDOO Neo.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In AOSP, both VIM3 and VIM3L have 2 bootloader flavors,
depending on A/B enablement.
For example, for vim3l, the naming is:
- u-boot_kvim3l_noab.bin : legacy support
- u-boot_kvim3l_ab.bin : A/B support
Prepare a defconfig to support u-boot_kvim3_ab.bin and
u-boot_kvim3l_ab.bin.
This is identical to khadas-vim3{l}_ab_android but will be updated in
the next commit.
Also update partitioning tables for A/B support.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-4-mkorpershoek@baylibre.com
This allows us to define extra board variables, such as "board" and
"board_name".
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-2-mkorpershoek@baylibre.com
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-7-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze is one the last two users of the CONFIG_SYS_RESET_ADDRESS
macro (the other is arch/powerpc/cpu/mpc8xx/cpu.c, but the macro is not
defined anywhere in powerpc code, so it should be removed there too).
Replace CONFIG_SYS_RESET_ADDRESS usage in start.S with
CONFIG_SYS_TEXT_BASE. If the reset address should really be
user-configurable, a new Kconfig option could be added.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-6-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The memory layout is taken from the device tree passed to us by
m1n1, so there is no need to define this.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The SMSC driver is using the old driver model.
Init the virtio system in vexpress64.c so that the network device is
discovered.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Move env var address values to #defines so they can be reused elsewhere.
Rename env var names to those recommended in the README and modify
addresses to allow more space for the kernel.
Fix issue where fdt is called with invalid arguments when booting
without a ramdisk.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Rename from vexpress_aemv8a.h -> vepxress_aemv8.h as new FVPs may not be
v8-A. No change in behavior.
This is towards future work to enable support for the FVP_BaseR.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
When using a recent kernel with a bunch of compiled-in
stuff the kernel image easily becomes bigger than 8 MB
yielding this error:
Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Fix this by bumping to SZ_64MB.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
-----BEGIN PGP SIGNATURE-----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=YdSB
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request of efi-next
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
This converts the following to Kconfig:
CONFIG_JFFS2_DEV
CONFIG_JFFS2_LZO
CONFIG_JFFS2_NAND
CONFIG_JFFS2_PART_OFFSET
CONFIG_JFFS2_PART_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_88F5182
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_IS_OPENRD_CLIENT
CONFIG_BOARD_IS_OPENRD_ULTIMATE
CONFIG_D2NET_V2
CONFIG_FEROCEON
CONFIG_FEROCEON_88FR131
CONFIG_INETSPACE_V2
CONFIG_KW88F6192
CONFIG_KW88F6281
CONFIG_KW88F6702
CONFIG_NET2BIG_V2
CONFIG_NETSPACE_LITE_V2
CONFIG_NETSPACE_MAX_V2
CONFIG_NETSPACE_MINI_V2
CONFIG_NETSPACE_V2
CONFIG_SHEEVA_88SV131
At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.
Signed-off-by: Tom Rini <trini@konsulko.com>
The only place we use CONFIG_CPU_ARMV8 was in the arm_dcc serial driver.
Switch this to CONFIG_ARM64 today, and if in the future we need finer
granularity tuning here, a new CONFIG_SERIAL option needs to be
introduced.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one of two ways. The first way is that it
is defined to a static value, of an unsigned long size. The second way
is that it is defined to something, typically a function, to determine
this value at run time.
However, in a few cases that function returns a static value. Change
that to using the static value directly.
In the case of using something at run time, convert everything to using
a function of the same name and prototype. This will allow for further
cleanups.
Finally, we have a few cases where the function is just not used, so
drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_CLK_FREQ_C100 and CONFIG_SYS_CLK_FREQ_C110 are
only used in one place and not changed by the board config file. Move
these out of the CONFIG namespace and in to the CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish this conversion we need to add a symbols for
SPL_SYS_NAND_SELF_INIT and TPL_SYS_NAND_SELF_INIT as there are cases
there where we need to, or need to not, use that framework as things
stand.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of CONFIG_SYS_FDT_ADDR this was being used to modify the
default value of fdt_addr / fdt_addr_r, which is not something to expose
in this manner and is not otherwise done. The case of SYS_ENV_ADDR is
similar but only done on the pic32mzdask platform, for scriptaddr.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
This is removing unused defines and correcting the default value to be
0x0 as we are a hex symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.
For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.
For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
In order to do this conversion, expose this option to the user and
use "save" not "safe" in the text.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_RPMB
This fixes a few platforms where the option was not taking effect as
intended.
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used as part of configuring the default environment for a
number of platforms. However, it is always set to 1 and the only time
it is part of Kconfig, it is used in a hard-coded manner. Hard-code the
value in the environment instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VIDEO_LOGO
Note that this option depends on CONFIG_DM_VIDEO now, since cfb_console is
deprecated. The only relevant code is now in splash.c
Drop the check for DM_VIDEO in that file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable SPL support in Kconfig and add some related option in
rk3568_common.h
Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com>
Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The resync of the device trees from Linux 5.16-rc3 caused aliases
to appear on the MMC devices which changed the numbering.
This changed the default boot device and caused boot failure.
Update the mmcdev variable to reflect the new aliases.
Signed-off-by: Adam Ford <aford173@gmail.com>
CONFIG_SYS_ATA_PORT_ADDR is not used in the code anymore. Drop it and use
ATA_PORT_ADDR() locally instead.
Drop CONFIG_IDE_RESET_ROUTINE and CONFIG_IDE_SWAP_IO which are also
unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used by sandbox since it uses driver model for the timer.
Drop it.
Also update the tools_only build to avoid build errors, since it does
actually build U-Boot too. Enable DM so we can use CONFIG_TIMER,
disable EFI_LOADER to avoid an error about board_quiesce_devices() and
disable NET to avoid having to define CONFIG_AVB_BUF_ADDR
Signed-off-by: Simon Glass <sjg@chromium.org>
This can go in the related header file. Drop the CONFIG option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add boot command "bootcmd_ram" to support autoboot from RAM.
This feature could be useful at the very initial state of chip design
when there is only a minimal set of peripheral. (e.g. without mmc and mac ..etc)
The kernel image is default to be loaded at 0x2000000 via debug port,
and the following script serves as an example:
spl()
{
cmd="riscv64-linux-gdb -q \
-ex \"target remote $host:$port\" \
-ex \"load\" \
-ex \"thread apply all set \\\$pc=&_start\" \
-ex \"thread apply all set \\\$a0=\\\$mhartid\" \
-ex \"thread apply all set \\\$a1=<dtb address>\" \
-ex \"restore u-boot.itb binary 0x200000\" \
-ex \"restore Image binary 0x2000000\" \
-ex \"c\" \
spl/u-boot-spl
"
echo $cmd
eval $cmd
}
The address where the kernel is loaded can be altered by
changing the value of KERNEL_IMAGE_ADDR.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM
This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LCD_DT_SIMPLEFB
This patch also renames this config to CONFIG_FDT_SIMPLEFB as the code in
common/lcd_simplefb.c support CONFIG_LCD and CONFIG_VIDEO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Using mmc.dtbo from rpi-firmware to switch the controller for the SD
card slot from sdhci to sdhost causes the numbering to change; the
SD card is then not recognized at boot. Add to the range checked.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
If bootloader was updated without running oem format, reboot will cause
boot loop because the SYSTEM stage fails.
Add a final PANIC stage running fastboot to permit recovery.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This can lead to GPT and BCB errors even if fastboot was selected early
by usb rom boot and the eMMC is blank/invalid.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
AST2600 leverages the FIT hash/signature verification to fulfill
secure boot trust chain. To improve the performance and save SW
code size for those crypto operations, the two HW crypto engine,
HACE and ACRY, are enabled.
However, both of the engines can only access to data stored in
DRAM space. Therefore, we need to move the FIT image into DRAM
before the booting.
This patch update the CONFIG_BOOTCOMMAND to execute the pre-defined
ENV variable which consists of FIT image copy to memory and booting.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Use a text file for the environment instead of the #define settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
This is a complicated set of #defines and it is painful to convert to a
text file. We can (once pending patches are applied) provide the same
functionality with bootmethod. Drop this for sandbox to allow conversion
to a text-file environment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Fix dfu_alt_info to use nor1 instead of the device name.
This reverts a part of commit 59bd18d4c4 ("configs: synquacer:
Remove mtdparts settings and update DFU setting") because the
commit a4f2d83414 ("mtd: spi: nor: force mtd name to "nor%d"")
changed the mtd device naming scheme to nor%d.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This symbol has been functionally dead for a long time. Remove the last
and recent re-introductions of setting it, and update the whitelist so
it will not be re-introduced again.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_TRACE
CONFIG_TRACE_BUFFER_SIZE
CONFIG_TRACE_EARLY
CONFIG_TRACE_EARLY_ADDR
CONFIG_TRACE_EARLY_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH
CONFIG_ENV_IS_NOWHERE
CONFIG_ENV_OFFSET
CONFIG_ENV_OVERWRITE
CONFIG_ENV_SECT_SIZE
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Signed-off-by: Tom Rini <trini@konsulko.com>
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
In some part of STM32MP15 support the CONFIG_TFABOOT can be replaced
by other config: CONFIG_ARMV7_PSCI and CONFIG_ARM_SMCCC.
This patch also simplifies the code in cpu.c, stm32mp1_ram.c and
clk_stml32mp1.c as execution of U-Boot in sysram (boot without SPL and
without TFA) is not supported: the associated initialization code is
present only in SPL.
This cleanup patch is a preliminary step to support SPL load of OP-TEE
in secure world, with SPL in secure world and U-Boot in no-secure world.
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add a configuration file "stm32mp15_st_common.h" to handle the
STMicroelectronics boards configuration and rename stm32mp1.h to
"stm32mp15_common.h" to handle the generic STM32MP15x series configuration.
The configuration file "dh_stm32mp1.h" is also renamed to
"stm32mp15_dh_dhcom" for the configuration of board based on the
dhelectronics STM32MP15x SOM.
In the STMicroelectronics board configuration the default bootcmd
"bootcmd_stm32mp" is updated to only select the extlinux file found on
SD-Card on STM32MP15x EV1 for boot from NOR device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LS1046A-QDS has CONFIG_SPI_FLASH_SST, CONFIG_SPI_FLASH_EON and
CONFIG_SPI_FLASH_STMICRO defines present in header. Move these entries
from header to defconfigs.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable support for update over EFI UpdateCapsule mechanism. This board
doesn't support setting EFI variables after ExitBootservices().
Therefore, we are also enabling EFI_IGNORE_OSINDICATIONS.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F
CONFIG_BOARD_LATE_INIT
CONFIG_DISPLAY_BOARDINFO
CONFIG_DISPLAY_BOARDINFO_LATE
Signed-off-by: Tom Rini <trini@konsulko.com>
Samsung S9 SM-G9600 - Snapdragon SDM845 version of the phone,
for China \ Hong Kong markets.
Has unlockable bootloader, unlike SM-G960U (American market version),
which allows running u-boot as a chain-loaded bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Hi-end qualcomm chip, introduced in late 2017.
Mostly used in flagship phones and tablets of 2018.
Features:
- arm64 arch
- total of 8 Kryo 385 Gold / Silver cores
- Hexagon 685 DSP
- Adreno 630 GPU
Tested only as second-stage bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Add support for Apple's M1 SoC that is used in "Apple Silicon"
Macs. This builds a basic U-Boot that can be used as a payload
for the m1n1 boot loader being developed by the Asahi Linux
project.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add MAINTAINERS entry]
- Add and enable watchdog driver
- Prepare for SYSRESET driven AXP poweroff
- Prepare for SoCs without MMC2
- Some fixes for extending SPL (SPL-DM for RISC-V)
- Some preparations for proper VBUS management
- Fix secure monitor move
commit 1ebfc0c631 ("sunxi: A23/A33/H3: Move sun8i secure monitor to
SRAM A2") attempted to move the secure monitor to SRAM A2. But not all
sun8i SoCs have SRAM A2, so a check was put in for SUNXI_SRAM_A2_SIZE to
avoid breaking the other SoCs.
However, because the header providing SUNXI_SRAM_A2_SIZE was not
included, this unintentionally skipped the new definitions on all SoCs.
Fix this by including the right header.
Fixes: 1ebfc0c631 ("sunxi: A23/A33/H3: Move sun8i secure monitor to SRAM A2")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Instead of declaring CONFIG_SPL_DRIVERS_MISC in board config header,
select it in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Instead of declaring CONFIG_SYS_MALLOC_SIMPLE dependant on
CONFIG_SPL_BUILD in board config header, select
CONFIG_SPL_SYS_MALLOC_SIMPLE in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reorder the definitions in Turris MOX' board config header, drop the
comment relics from when this file was copied, fix indentation.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move the config option CONFIG_I2C_MV to a Kconfig option
CONFIG_SYS_I2C_MV and move the default definition from config header
files into defconfigs.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move config options CONFIG_LAST_STAGE_INIT and
CONFIG_DISPLAY_BOARDINFO_LATE to turris_mox_defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add code to build the eMMC variant of the Colibri iMX6ULL, i.e. the
'Colibri iMX6ULL 1GB' which has a eMMC instead of the raw NAND used
on other SKUs.
Related-to: ELB-4056, ELB-4057
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Integrate new Toradex SKU 0062 Colibri iMX6ULL 1GB IT. This commit
basically adjusts three parameters of the RAM settings:
Increase density from 4Gb to 8Gb
Increase ROW address from 15 to 16
Increase tRFC (refresh command time) from 260 to 350
This timing is valid for all Toradex Colibri iMX6ULL SKUs
Related-to: ELB-4055, ELB-4057
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Variable "kernel_image" is used in boot.scr script only, that sets its
own default value to the constant string @@KERNEL_IMAGETYPE@@ in case
"kernel_image" is not set.
The default name of the kernel image shipped with BSP 5.x is "Image.gz".
Setting kernel_image="Image" as a pre-defined u-boot variable
breaks booting systems with modern versions of boot.scr, whereas
renaming it fixes booting with modern scripts and does not break working
of earlier versions of boot.scr.
While at it also update the copyright period, rather than hard-coding
fdtfile default fdt_board to dev for the Verdin iMX8M Mini and fix its
closing #endif comment.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Even if board can be successfuly built, CI goes in deadlock (see thread
on https://www.mail-archive.com/u-boot@lists.denx.de/msg419663.html).
This is caused by SYS_CONFIG set in header file and because defconfig
for the board is out of sync with Kconfig. As result, buildman goes on
to read from stdin until an OOM is reached.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Frieder Schrempf <frieder.schrempf@kontron.de>
Bulletproof the default boot command with reset statements in case
any command in the chain would fail. In case a failure were to happen,
the board will reset, increment boot counter and retry the procedure.
In case the failures persist and the boot counter reaches the bootlimit,
U-Boot starts altbootcmd instead of the default bootcmd boot command.
The altbootcmd swaps the default boot partition for the other boot
partition, which is an identical copy or an older copy, and tries
booting from that one instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Move setting CONFIG_BOOTCOMMAND to the mx7ulp_com_defconfig file.
It also allows replacing the default CONFIG_BOOTCOMMAND without
code modification.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On mvebu this is defined if and only if !ARM64.
Otherwise it is defined for boards with ARCH_MX23, ARCH_TEGRA and
ARCH_ZYNQ, and also for SOC_AR934X (tplink_wdr4300).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This option is only used for
mx23evk_defconfig
mx23_olinuxino_defconfig
which are the only i.MX23 boards.
Add depend on ARCH_MX23 and default to y.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
In preparation for moving this option to Kconfig, rename it to be
consistent with other USB EHCI Kconfig options.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Remove the latest reference of CONFIG_CONS_NONE in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the latest reference of CONFIG_SYS_FLASH_AMD_CHECK_DQ7 in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the latest reference of CONFIG_NO_RELOCATION in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This define was left over from a previous revision, and was never used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove some config finishing by _ badly added by
scripts/build-whitelist.sh when joker is used in comments.
for example:
doc/uImage.FIT/command_syntax_extensions.txt:
... #ifdef CONFIG_OF_* | ...
cmd/nvedit.c:# error Define one of CONFIG_ENV_IS_IN_{EEPROM| \
FLASH|MMC|FAT|EXT4|\
Remove also configs only used in comments:
- CONFIG_BOOGER in include/linux/kconfig.h
- CONFIG_COMMANDS
- CONFIG_INIT_IGNORE_ERROR
- CONFIG_REG_*
- CONFIG_HOTPLUG : drivers/watchdog/omap_wdt.c:18
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The EMC frequency tables are created from a training sequence performed
during early boot and passed in via a reserved memory region by nvtboot.
Copy this table to the kernel DTB so that the kernel can use it to scale
the EMC frequency at runtime.
Note that early bootloaders store the EMC table at an address that
currently intersects with the load address of the initial ramdisk. In
order to avoid copying the table to a different address, simply change
the load address for the initial ramdisk in U-Boot.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).
Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.
This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Account for the changes done between merge proposal and the final merge.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_VIDEO_MXS from board headers to Kconfig
and drop it from obsolete cfb_console driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Remove the latest reference of CONFIG_USER_LOWLEVEL_INIT in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move CONFIG_BOOTCOMMAND defined in Kconfig in the board defconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Using the tools moveconfig.py to move the following config in the
defconfig files:
CONFIG_USB_HOST_ETHER
CONFIG_USB_ETHER_ASIX
CONFIG_USB_ETHER_MCS7830
CONFIG_USB_ETHER_SMSC95XX
These option are already migrated since the commit f58ad98a62 ("usb: net:
migrate USB Ethernet adapters to Kconfig") and the commit ae3584498b
("usb: net: migrate CONFIG_USB_HOST_ETHER to Kconfig").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the CONFIG_STM32_FLASH to Kconfig by using
tools/moveconfig.py
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This reverts commit d5d726d3cc,
which breaks boards which ship with multiple SD/eMMC sockets.
This stm32mp1.h config is not used only by the ST reference
boards, but all the other STM32MP1 based boards in U-Boot, so
changes to this stm32mp1.h cannot break the other boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
These platforms never had to support an ATAGs-based Linux Kernel, so
remove the options.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
When using SWUpdate, it is necessary to toggle between partitions.
Use the 'mmcpart' environment variable to accomplish that.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The CONFIG_SPL_MAX_SIZE definition did not account for all areas that
are used by the boot ROM according to the manual, causing boot failures
due to truncated SPL images when actually hitting this limit.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
The BSP platform LmP supports the board NXP iMX8QM MEK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
The BSP platform LmP supports the board NXP iMX8M Plus EVK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
The BSP platform LmP supports the board NXP iMX8M Mini EVK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
JetHub devices uses its own boot sequence with "rescue" button
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SCSI target to be able to boot from the SATA disks on the Odroid HC4 using
an on-board AHCI PCIe controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Typically platforms will define CONFIG_SYS_NAND_PAGE_COUNT based on
CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE. Switch to this
in preparation for migrating CONFIG_SYS_NAND namespace to Kconfig.
Cc: Marek Vasut <marex@denx.de>
Cc: Olaf Mandel <o.mandel@menlosystems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These platforms do not currently enable NAND, remove these references.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This value is not used by u-boot, and it should not. The load address
of an OPTEE image is defined by said image. Either a uImage or a FIT
will have a defined load address and entry point. Those values are the
correct ones, not CONFIG_OPTEE_LOAD_ADDR.
Commit f25006b96e ("optee: Add CONFIG_OPTEE_LOAD_ADDR") justifies
this config by requiring its presence in u-boot's .config for other
images as part of a larger build, claiming it is "the best way".
This argument is not persuasive. U-boot's configuration is driven by
platform requirements, not the other way around. It seems more likely
that the argument is conflating tooling issues with Kconfig. Yocto and
buildroot have excellent mechanisms for defining values across the
board (pun intended). u-boot's Kconfig is the wrong place to do it.
Furthermore, it is not "best" for u-boot because it hardcodes a value
which is then not used. In fact the load address that u-boot uses is
the one derived from the OPTEE image.
Confused yet? I sure was. To prevent future confusion, remove
CONFIG_OPTEE_LOAD_ADDR.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This adds support for the IOT2050 Basic and Advanced devices. The Basic
used the dual-core AM6528 GP processor, the Advanced one the AM6548 HS
quad-core version.
Both variants are booted via a Siemens-provided FSBL that runs on the R5
cores. Consequently, U-Boot support is targeting the A53 cores. U-Boot
SPL, ATF and TEE have to reside in SPI flash.
Full integration into a bootable image can be found on
https://github.com/siemens/meta-iot2050
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
A number of platforms are still defining CONFIG_SYS_BAUDRATE_TABLE to
the fallback default of "{ 9600, 19200, 38400, 57600, 115200 }", but
with varying whitespace, or were introduced after the default fallback
was added. Use the default table here.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last armada100 platform, remove that support
as well.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr
support").
Fixes: 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The comment is no longer meaningful due to DT conversion, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The MXC_EHCI_MODE_ definitions are redundant. Replace MXC_EHCI_MODE_SERIAL
with the equivalent PORT_PTS_SERIAL.
Only the zmx25 platform is affected.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
We have individual SOC symbols for each keystone 2 platform. Use the
existing CONFIG_ARCH_KEYSTONE rather than CONFIG_SOC_KEYSTONE to
encompass all of the keystone families.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_OMAP_EHCI_PHY1_RESET_GPIO
CONFIG_OMAP_EHCI_PHY2_RESET_GPIO
CONFIG_OMAP_EHCI_PHY3_RESET_GPIO
To do this, we also introduce CONFIG_HAS_CONFIG_OMAP_EHCI_PHYn_RESET_GPIO
options to get setting the GPIO number.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have one places that uses this symbol and CONFIG_TARGET_OMAPL138_LCDK
works equally well, switch to that.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the main option for handling drivers/dma/keystone_nav* to Kconfig,
and enable it by default. All of the sub-symbols are not configurable,
so remove them from the CONFIG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
The COFNIG_KEYSTONE_RBL_NAND option is always enabled for the driver on
keystone platforms, but not older davinci platforms. Use def_bool for
the symbol. For CONFIG_KEYSTONE_NAND_MAX_RBL_PAGE, it's only used within
the driver and derived from another symbol, so remove CONFIG from the
name. Finally, CONFIG_KEYSTONE_NAND_MAX_RBL_SIZE is a bit more fixed.
For now, use the value directly. Long term, as part of DM'ifying NAND,
this should come from the device tree.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since cm_t35 was removed, CONFIG_CM_T3X does not exist. This lets us
simplify the code in board/compulab/common/eeprom.c a bit.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time, all platforms that had previously used
drivers/usb/phy/omap_usb_phy.c have been migrated to DM and related
options. Remove this now unused code and some related unused defines.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only used in the aemif driver that is otherwise currently
keystone2 centric. Moving forward, if this is applicable to some other
platform then such base addresses should be able to be obtained via the
device tree. Use KS2_AEMIF_CNTRL_BASE directly now rather than
indirectly.
Signed-off-by: Tom Rini <trini@konsulko.com>
vexpress_ca9x4 is seemingly the only board except for qemu_arm which
is able to run U-Boot correctly, using the `-M vexpress-a9` option to
QEMU. Building for qemu_arm and running qemu-system-arm with the `-M
virt` argument has a number of downsides, most importantly that it
only supports virtio storage drivers. This significantly reduces its
usefulness in testing memory card and Flash solutions, especially when
the tested images are from a third party source.
So therefore we reintroduce the vexpress_ca9x4 board in this commit,
with the explicit goal of using it with QEMU.
A number of differences to note from the original:
* Since the board was apparently unmaintained, I have now set myself
as the maintainer.
* The board has been converted to use the driver model, which was the
reason it was removed in the first place.
* The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed
in the same commit, are not necessary for the QEMU use case, and
have been omitted.
* An `mmc0` alias was introduced in the dts file. The mmc is not
detected correctly without this, now that it's based on the device
tree instead of the board's init function.
* A couple of other nodes were removed because they were problematic
when trying to run the UEFI bootmgr. Once again, the primary use
case here is QEMU, and these nodes are not needed for that to work.
* Unnecessary board init code has been removed, thanks to driver model
and device tree.
* `CONFIG_OF_EMBED` has been enabled. I know this goes against
recommended practice, but there doesn't seem to be any other way to
pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument
does not work, I suppose because U-Boot doesn't use the same
mechanics as the kernel when it's booting.
* Load addresses have been changed to fit QEMU use case.
People wanting to get a more detailed, yet somewhat isolated, diff
between this and the original, can run this command:
git diff c6c26a05b89f25a06e7562f8c2071b60fd0c9eac~1 -- \
$( git diff-tree --diff-filter=A -r --name-only HEAD~1 HEAD)
(Make sure to either check out this commit first, or replace HEAD with
the commit ID of this commit)
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr
support").
Fixes: 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFKxpEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBLaB/0XsIdkGAvcHLWW8yUg
27GiRznikNKwn9/qIj2ByraoUd4BvxdQV4gKHR1R9n0sgYh/8VMyLbmhRoCRKFwP
3mQ0MUyjaeU5sEWzasovJVpXhuUapEiV0jEg6t3Lgwd3mp2QK2Pk87zoleQfZNkb
VAVCnt1T+kb3y0W9oa3XZbuH2wam9T5pNWRGW70JbgzdwJNKLO1Qo7MfcUNiDxJu
Jf7uXtYwwILlN38G1KSk1ymMjfaotCqj7RzNaV3Ero57MVj3VzerKGb7H+XPOYf2
nYXyietYLJJkzvHzSDwIdCSVlOSQL8QqVB8GCmLiNQD4tG830RcvSJnYpRLylWQK
6F+Y
=Q/aS
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.01 cycle:
This feature set includes : the support for CPU driver for arm926
(sam9x60 device); changes required for OP-TEE boot for sama5d2_xplained
and sama5d27_som1_ek boards; QSPI boot configuration for sama5d2_icp;
starting to remove old Kconfig unused symbols from config_whitelist.txt
(work will take more time); also small fixes and updates in mach, DT,
configs, etc.
The comment is no longer meaningful due to DT conversion, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The MXC_EHCI_MODE_ definitions are redundant. Replace MXC_EHCI_MODE_SERIAL
with the equivalent PORT_PTS_SERIAL.
Only the zmx25 platform is affected.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
CONFIG_SYS_AT91_CPU_NAME looks to be unused.
Remove it and remove it from config_whitelist.txt
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Rewrite the CONFIG_BOOTCOMMAND only if it's not previously configured from
defconfig file.
This allows the user to select from defconfig/menuconfig the desired
boot command.
Adjust the current board defconfigs to reflect the default booting command
for the specific ENV configuration.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
When using OP-TEE, address range [0x20000000 - 0x22000000] is reserved.
This modification allows to have a system which always work even when
OP-TEE is present.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
When using OP-TEE, address range [0x20000000 - 0x22000000] is reserved.
This modification allows to have a system which always work even when
OP-TEE is present.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Note that we have to add CONFIG_SPIFLASH to scripts/config_whitelist.txt
because it's not really migrated at this point.
Acked-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Acked-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Acked-by: Oleksandr Zhadan and Michael Durrant <arcsupport@arcturusnetworks.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Handle CONFIG_SPIFLASH differently and delete Kconfig file]
Signed-off-by: Tom Rini <trini@konsulko.com>
On J721e R5 SPL, dfu buffer for loading sysfw.itb image gets allocated
before DRAM gets initialized. So, the buffer gets allocated in MCU L3
RAM. The current buffer size to be allocated is 256KB and the available
total heap memory is 0x70000 (448KB). This leads to NOMEM errors during
allocation.
In other cases when constraints such as above are not present fix the size
of buffers to the sector size in OSPI for proper functioning.
Also, if CONFIG_SYS_DFU_DATA_BUF_SIZE is defined and
CONFIG_SYS_DFU_MAX_FILE_SIZE is not defined then the max file size for dfu
transfer is defined as CONFIG_SYS_DFU_DATA_BUF_SIZE.
Fix these by setting appropriate buffer sizes in their respective defconfig
files and defining the max file size as 8 MB which is the default dfu
buffer size.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add env variables for booting to kernel from USB MSC device. The second
partition in the USB MSC device needs to formatted as ext4 file system with
kernel and dtb images, present in the /boot folder.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This commit uses the existing DEFAULT_MMC_TI_ARGS and
DEFAULT_FIT_TI_ARGS defintions to replace the 'mmc*' environment
variables in the configuration. The check for the 'boot_fit' is handled
like the 'am335x_*' boards with 'CONFIG_BOOTCOMMAND'.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Fix baudrate value 5150000 which was added in commit ead4864fa6 ("arm:
mvebu: a38x: Define supported UART baudrates").
Exact value for divisor 3 with 250 MHz TCLK is 5208333 baudrate. In above
commit I incorrectly rounded it to 5150000 value due to testing with
USB-UART hw which incorrectly reported exact value and divisor configured
on other other end of UART link.
Fix this value to 520000 baudrate which is more close to the exact hardware
value and also has less fraction parts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: ead4864fa6 ("arm: mvebu: a38x: Define supported UART baudrates")
Reviewed-by: Stefan Roese <sr@denx.de>
All of these configs exist. Stick to using CONFIG_[ST]PL_HASH, and drop all
references to CONFIG_[ST]PL_HASH_SUPPORT. This means we need for
CHAIN_OF_TRUST to select SPL_HASH now.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Add TPL case, fix CHAIN_OF_TRUST, other tweaks]
Signed-off-by: Tom Rini <trini@konsulko.com>
As this is only useful when booting with ATAGs, which are now largely
disabled, remove this value for the remaining platforms. We have a few
places in the code that had been testing for MACH_TYPE as a sort of
internal logic. Update those to use different but still correct CONFIG
symbols.
Cc: Phil Sutter <phil@nwl.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
No iMX platforms have supported ATAG-based booting. They have however
re-used the CONFIG_SERIAL_TAG option as a way to enable support of
reading the OTP fuses and setting the serial# environment variable in
some cases. Change the warp7 support to use this symbol, use this for
updating the rest of the imx7 code, and update the imx8 conditionals.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
On the HiFive Unmatched a PCI to SATA adapter may be used to install a SATA
drive. Enable booting from it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The code under drivers/net is related to ethernet networking drivers, in
some fashion or another. Drop these from the top-level Makefile and
also move the phy rule into drivers/net/Makefile which is where it
belongs. Make the new rule for drivers/net check for the build-stage
relevant ETH symbol.
Fix up some Kconfig dependencies while we're here to mirror how the
Makefile logic now works.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Introduce ETH, Kconfig dependency changes, am43xx fix]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_POWER_I2C
CONFIG_POWER_LEGACY
They are handled at the same time due to a dependency between them.
Update the Makefile rule to use legacy power only in U-Boot proper.
Unfortunately a separate rule is needed in SPL to be able to build
legacy power. Add SPL related symbols for both, to allow for SPL-only
usage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: More SPL related cleanups, reword commit message]
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used in pre-driver model code and much of it has never
been converted to driver model.
We want to add a new option to enable power support, so we can use a
simple rule in the Makefile. Rename this one, which is really about
a particular implementation of power.
Also update the pmic.h header file so it either includes the legacy
API or the driver model one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a proper Kconfig option for SPL so we can remove the hack in some of
the board config files.
This involves adding CONFIG_SPL_DM_PMIC to some of the configs as well
as updateing the Makefile rule for PMIC_RK8XX to exclude SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Add SPL_PMIC_RK8XX, enable when needed, handle undef of
CONFIG_DM_PMIC_PFUZE100 as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
Per a request from Andre Przywara and agreed with by Peter Hoyes, the
vexpress aemv8r support wasn't quite ready to be merged, but the
discussion had moved off list. We should keep the first patch in the
series for now, but revert the rest. This reverts the following
commits:
e0bd6f31ce doc: Add documentation for the Arm vexpress board configs
30e5a449e8 arm: Use armv8_switch_to_el1 env to switch to EL1
b53bbca63b vexpress64: Add BASER_FVP vexpress board variant
2f5b7b7490 armv8: Add ARMv8 MPU configuration logic
37a757e227 armv8: Ensure EL1&0 VMSA is enabled
Signed-off-by: Tom Rini <trini@konsulko.com>
The BASER_FVP board variant is implemented on top of the BASE_FVP board
config (which, in turn, is based on the Juno Versatile Express board
config). They all share a similar memory map - for BASER_FVP the map is
inverted from the BASE_FVP
(https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map)
* Create new TARGET_VEXPRESS64_BASER_FVP target, which uses the same
board config as BASE_FVP and JUNO
* Adapt vexpress_aemv8a.h header file to support BASER_FVP (and rename
to vexpress_aemv8.h)
* Enable config to switch to EL1 for the BASER_FVP
* Create vexpress_aemv8r defconfig
* Provide an MPU memory map for the BASER_FVP
For now, only single core boot is supported.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[trini: Add MAINTAINERS, move BOOTCOMMAND to defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Make use of the new drivers for ARM U8500 introduced in the U-Boot
2021.10 merge window by adding basic support for USB Fastboot with
the "stemmy" board. As a first step this will always boot directly
into USB Fastboot for now with the console displayed on the screen
to make that obvious.
Samsung uses quite strange GPT partition labels on these boards,
so also add a bunch of fastboot_partition_alias_* to make this more
easy to use.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Define all standard baudrates plus 3 non-standard high speed:
3125000 4000000 5150000
3125000 matches divisor 5 with 250 MHz TCLK and divisor 4 with 200 MHz TCLK.
4000000 is the rounded value for divisor 4 with 250 MHz TCLK (3906250) and
divisor 3 with 200 MHz TCLK (4166666).
5150000 is the rounded value (5208333) for divisor 3 with 250 MHz TCLK.
Testing showed that rounded value is more stable then exactly calculated.
And it is the highest possible baudrate which is stable on A38x platform.
Any other baudrate values above 2500000 are unstable, which is reason why
e.g. standard value 3000000 is not defined, and it is needed to use
non-standard value 3125000.
Tested all defined UART baudrates on Turris Omnia (A38x with 250 MHz TCLK).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
We move the SYS_CACHE_SHIFT_N options from arch/arm/Kconfig to
arch/Kconfig, and introduce SYS_CACHE_SHIFT_4 to provide a size of 16.
Introduce select statements for other architectures based on current
usage. For MIPS, we take the existing arch-specific symbol and migrate
to the generic symbol. This lets us remove a little bit of otherwise
unused code.
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Leo <ycliang@andestech.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Rather than using CONFIG_SABRELITE to set FDTFILE for only that
platform, switch to always setting this based on
CONFIG_DEFAULT_DEVICE_TREE as this should always match the kernel
device tree name anyhow.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not
CONFIG_LOADADDR.
- Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as
noted, we use CONFIG_SYS_LOADADDR.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Guard most of the options in drivers/ddr/fsl/Kconfig with
SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this symbol can either be a fixed value or the function
get_board_ddr_clk, migration is tricky. Introduce a choice of DYNAMIC
or STATIC_DDR_CLK_FREQ. If DYNAMIC, we continue to use the board
defined get_board_ddr_clk function. If STATIC, set CONFIG_DDR_CLK_FREQ
to that value and now include/clock_legacy.h contains the function
prototype or defines get_board_ddr_clk() to that static value. Update
callers to test for DYNAMIC or STATIC.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a number of CONFIG symbols to express the fixed size of system
memory. For now, rename CONFIG_DDR_FIXED_SIZE to CONFIG_SYS_SDRAM_SIZE
and adjust usage to match that CONFIG_SYS_SDRAM_SIZE expects the entire
size rather than MiB.
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <marek.behun@nic.cz>
Move CONFIG_DDR_32BIT/64BIT to Kconfig as a choice for Armada XP
platforms. Make 64bit the default as this mirrors the current code.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
These symbols are now either unused or were only used within the config
file to determine other logic, which could be done in a way that doesn't
further pollute the CONFIG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than using CONFIG namespace for logic internal to
include/configs/astro_mcf5373l.h to select ASTRO_ID (and populate the
default environment), strip CONFIG from the various options used and
set.
Signed-off-by: Tom Rini <trini@konsulko.com>
There are an assortment of hard-coded CONFIG_BOOTCOMMAND options in some
board headers. Rework these so that they do not add to the CONFIG
namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate CONFIG_GICV2 and CONFIG_GICV3 to Kconfig. We still have the GIC
related registers that need to be handled more cleanly but start by
moving this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
- As there are no boards that use different values for speed / slave on
different buses, use a single option.
- Switch to using the common SYS_I2C_SPEED / SYS_I2C_SLAVE options.
- Introduce _HAS_ options for additional buses as only the first one is
common to all users.
- Convert all remaining symbols to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Migrate SYS_I2C_SH and related defines to Kconfig
- Remove currently unused SYS_I2C_SH related defines
- Cleanup related README section.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_MXC
CONFIG_SYS_I2C_MXC_I2C1
CONFIG_SYS_I2C_MXC_I2C2
CONFIG_SYS_I2C_MXC_I2C3
CONFIG_SYS_I2C_MXC_I2C4
Signed-off-by: Tom Rini <trini@konsulko.com>
The omap24xx I2C driver uses its own CONFIG namespace for common I2C
variables. Rather than convert more of them to Kconfig, rename these to
the common I2C ones and remove the entirely unused functionality. As
part of this, we make the am335x_shc platforms consistent with their
intended speed values.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert SYS_I2C_EARLY_INIT to Kconfig, and make it depend on
SPL_SYS_I2C_LEGACY. Remove the weak implementation as it's either
something that needs to exist for real, or shouldn't be called.
Signed-off-by: Tom Rini <trini@konsulko.com>
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_SOFT
CONFIG_SYS_I2C_SOFT_SPEED
CONFIG_SYS_I2C_SOFT_SLAVE
Signed-off-by: Tom Rini <trini@konsulko.com>
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time, there's no systems with "U-Boot environment
exists on an EEPROM which is accessed over the I2C bus" that sets this
option. Drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Finish moving this driver to Kconfig.
- Update the dependency logic for Exynos5 too
- Remove the unused CONFIG_SYS_I2C_S3C24X0_SPEED variable
- Drop CONFIG_SYS_I2C_S3C24X0_SLAVE as it's always set to 0.
- Move the internal SYS_I2C_S3C24X0_SLAVE define closer to the only user.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The instances of CONFIG_SYS_I2C_EEPROM_ADDR on these platforms doesn't
match up with the rest of the EERPOM related defines in U-Boot. Move
these out of the CONFIG namespace rather than make complex Kconfig
logic.
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
As the code reads now, making this code path use
CONFIG_SYS_IVM_EEPROM_ADR rather than CONFIG_SYS_I2C_EEPROM_ADDR seems
to make sense as the rest of the EEPROM infrastructure isn't used on
these platforms.
Cc: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
The shc platforms do not make use of the rest of the EEPROM
infrastructure. Rather than make more elaborate Kconfig logic, remove
this setting from the CONFIG namespace.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This platform does not use any of the standard EEPROM functionality and
instead provides its own. Use a local namespace for the I2C related
defines to access the EEPROM.
Cc: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Rework the default environment a bit to not use non-standard
CONFIG_ENV_... names and similar one-off CONFIG names.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Rename CONFIG_ENV_KS2_BOARD_SETTINGS to ENV_KS2_BOARD_SETTINGS so that
it better fits with the rest of the environment addition macros.
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename CONFIG_EXTRA_ENV_BOARD_SETTINGS to EXTRA_ENV_BOARD_SETTINGS in
order to not further add to the CONFIG namespace.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
There are a number of DWC2 configuration options that are set in dwc2.h
and referenced in dwc2.c only. Move these out of the CONFIG_DWC2
namespace and in to the DWC2 namespace. Note that hikey was defining an
option that was already always enabled, so we can remove that hunk.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename to common file name to used by all SOC64 devices and change
"_S10_" to "_SOC64_" in base_addr_soc64.h.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Update boot-commands to load device-tree from
boot-device at 'fdt_addr_r' address in DDR
during distro-boot.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Use moveconfig.py script to convert below defines to Kconfig and move
these entries to defconfigs.
CONFIG_CORTINA_FW_ADDR
CONFIG_CORTINA_FW_LENGTH
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This symbol was largely migrated, except for one case. Update it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Convert GoFlex Home Ethernet and SATA to Driver Model (Tony)
- mvebu: Automatically detect CONFIG_SYS_TCLK (Pavel)
- mvebu: sata_mv: Fix HDD identication during cold start (Tony)
- a37xx: pci: Fix handling PIO config error responses (Pavel)
- Other minor misc changes and board maintainer updates
- sei610 & meson64_android cleanups to prepare android 11 boot support
- use Android BCB mechanism for reboot reason instead of HW reboot flag
- Switch meson64_android boot flow to use abootimg for A/B, AVB and DTBO support
-----BEGIN PGP SIGNATURE-----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=RZ8+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20210810' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- odroid-n2: fix fdtfile suffix for n2-plus
- sei610 & meson64_android cleanups to prepare android 11 boot support
- use Android BCB mechanism for reboot reason instead of HW reboot flag
- Switch meson64_android boot flow to use abootimg for A/B, AVB and DTBO support
Basically all, i.e. rk3036.dtsi, rk3128.dtsi, rk3xxx.dtsi, rk322x.dtsi,
rk3288.dtsi, rk3308-u-boot.dtsi, rk3328-u-boot.dtsi, rk3399-u-boot.dtsi
and px30-u-boot.dtsi Rockchip SoC devicetrees which have mmc indexes
are defining eMMC as mmc0 and sdmmc as mmc1.
This means that the rule to try to boot from the SD card first is ignored,
which as per comment is what we want and is important for distros, which
rely on that.
Fix this by setting the correct mmc index, i.e. first from mmc1 (SD card),
second from mmc0 (eMMC).
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable support to the 2 NOR flashes on the QEMU RISC-V virt machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Config option CONFIG_SYS_TCLK is set by kw88f6281.h and kw88f6192.h files
to correct SOC/platform value. So do not overwrite it in board config
include files.
Kirkwood 88F6180 and 88F6192 uses 166 MHz TCLK and Kirkwood 88F6281 uses
200 MHz TCLK.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu axp platform always uses fixed 250 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Now every #if-#else case of soc.h file defines CONFIG_SYS_TCLK, so remove
useless default CONFIG_SYS_TCLK value from the end of soc.h file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu msys platform always uses fixed 200 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Bit 20 in SAR register specifies if TCLK is running at 200 MHz or 166 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Bit 15 in SAR register specifies if TCLK is running at 200 MHz or 250 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Activate the following Kconfig options:
* AVB for Android Verified Boot support
* ADTIMG for merging DTBOs
* ABOOTIMG for extracting Android boot image
Also rework the partitioning tables:
- add a misc partition to handle BCB messages
- add a dtbo partition to store various DTBOs
- add a vbmeta partition for AVB hashes
- Merge vendor and system into the "super" partition
Note: avb support is disables by default. To activate it:
=> setenv force_avb 1;
=> saveenv;
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
doc/README.gpt states:
> The fields 'uuid' and 'uuid_disk' are optional if CONFIG_RANDOM_UUID is
> enabled. A random uuid will be used if omitted or they point to an empty/
> non-existent environment variable. The environment variable will be
> set to the generated UUID. The 'gpt guid' command reads the current
> value of the uuid_disk from the GPT.
Since we have CONFIG_RANDOM_UUID=y, remove the hard-coded uuids
and use meaningful variable names instead.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
There is a mix of spaces and tabs at the leading \. This makes updating
theses lines harder.
Add a single space before each \ for some consistency.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Since Android 10, we are required to use a "dtbo" partition which
includes the various device-tree overlays [1].
It's also possible to provide a "dtb" partition.
This is supported via the "abootimg" command.
On Yukawa, the assumption is that we have only a "dtbo" partition, which
includes all board dtbs and their dtbos [2]
[1] https://source.android.com/devices/architecture/dto/partitions
[2] https://android.googlesource.com/device/amlogic/yukawa/+/refs/heads/master/build/tasks/dtimages.mk#16
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
BOOT_CMD might be different based on CONFIG_CMD_ABOOTIMG.
To prepare for abootimg support, extract the boot command
to a dedicated macro.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Implement A/B slot selection using the U-Boot ab_select command.
Keep support for non A/B.
Not: We need to redefine the recovery partition label, as RecoveryOS
is included in the boot image for A/B systems [1]
[1] https://source.android.com/devices/tech/ota/ab/ab_implement#recovery
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
AVB (Android Verified Boot) is well supported in U-Boot already.
Add support for it in meson64_android.
This is controlled by the "force_avb" environment variable and the
CONFIG_CMD_AVB option.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
To prepare for AVB support, increase SYS_MALLOC_LEN to 128M.
This value has been found by testing the following on khadas vim3l:
=> avb init
=> avb verify
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Permit redefining SYS_MALLOC_LEN for board specific configs.
This is especially useful for Android with AVB, which requires a malloc
length of 128M.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped support for networking and splash screen as these need
to be properly converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add PCIe reset gpio to the Bx50v3 devicetree and get get rid of
CONFIG_PCIE_IMX_PERST_GPIO.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Do not pass the console baudrate to the 'console' variable
to avoid the baudrate being passed twice when extlinux.conf
contains the standard: console=${console},${baudrate} format.
cat /proc/cmdline
root=PARTUUID=00000000-01 rootwait rw console=ttymxc0,115200,115200
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The bootparams do not have to be at fixed location, they can be
dynamically mallocated instead. Make it so to get rid of another
fixed assignment.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Symbol CONFIG_SYS_ID_EEPROM is defined in include/configs/MPC8548CDS.h
but never used. Remove it here and from the whitelist.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Move the PSCI runtime code for H3/A23/A33 into SRAM
- Pick the environment from the actual MMC boot device (SD card vs.
eMMC)
- Plus a small improvement from Icenowy, just for good measure.
So far for the H3, A23, and A33 SoCs, we use DRAM to hold the secure
monitor code (providing PSCI runtime services). And while those SoCs do
not have the secure SRAM B like older SoCs, there is enough (secure)
SRAM A2 to put the monitor code and data in there instead.
Follow the design of 64-bit SoCs and use the first part for the monitor,
and the last 16 KiB for the SCP firmware. With this change, the monitor
no longer needs to reserve a region in DRAM.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: amend commit message, fix R40 and V3s build]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- Enable DM SATA, removed IDE driver, and add SATA MV driver.
- Use ethernet PHY names from device tree in default boot command
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Macro CONFIG_SYS_U_BOOT_OFFS is set but not used anymore. Remove it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that proper load and execution addresses are set in v1 kwbimage we
can use it for loading and booting U-Boot proper.
Use the new spl_parse_board_header() function to implement parsing the
kwbimage v1 header. Use information from this header to locate offset and
size of the U-Boot proper binary, instead of using the legacy U-Boot
header which is prepended to the U-Boot proper binary stored at fixed
offset. This has the advantage that we do not need to relay on legacy
U-Boot header anymore and therefore U-Boot proper binary can be stored at
any offset, as is the case when loading & booting U-Boot proper by
BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL
code anymore.
Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case
BootROM is used for loading and executing U-Boot proper. This reduces the
size of U-Boot's SPL image. By default these config options are enabled
and so BootROM loading is not used. In some cases BootROM reads from SPI
NOR at lower speed than U-Boot SPL. So people can decide whether they
want to have smaller SPL binary at the cost of slower boot.
Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO,
CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT,
CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and
CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply"
(which can be selectivelly turned off and causes booting via BootROM).
Options CONFIG_SYS_SPI_U_BOOT_OFFS,
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to
zero as they define the location where kwbimage header starts. It is the
location where BootROM expects start of the kwbimage from which it reads,
parses and executes SPL part. The same applies to option
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one.
Update all config files to set correct values of these options and set
CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot
proper starts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Whenever we test for boot-fastboot in the BCB, it means that Android
wants us to boot into recovery with a special mode (fastbootd).
Force reboot into recovery in that case.
Note: we don't erase the bcb on purpose here: recoveryOS needs to read
the BCB as well to know if it boots into regular recovery mode or
fastbootd mode.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Right now meson64_android does not know how to boot into Android
Recovery: it simply falls back to "fastboot" mode in the bootloader.
Implement the boot to recovery.
While at it, use the standard BCB way instead of a sm for consistency.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
As of today, we use a "vendor specific" secure monitor call for the
reboot reason (sm).
We should not need this. Android uses the BCB (Bootloader Control Block)
to communicate with the bootloader.
Implement "reboot into bootloader" using the standard BCB way instead of
using sm calls.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The console bootargs are already set from the kernel commandline.
On Android, this is done in yukawa at [1]
Don't set it in the bootloader since it's overridden by the kernel anyways.
[1] https://android-review.googlesource.com/c/device/amlogic/yukawa/+/1112994
Signed-off-by: Guillaume La Roque <mkorpershoek@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
To display the bootup logo, we read the gpt and assume that the
partition with index "2" will be the "logo" partition.
This might not always be the case, and it's very error-prone.
Load the logo partition by label instead of by index.
Signed-off-by: Guillaume La Roque <mkorpershoek@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
To boot Android, we read the gpt and assume that the partition with
index "1" will be the "boot" partition.
This might not always be the case, as there are no requirements from
Android on the partition order.
However, Android does seem to use the "boot" label quite a lot on their
public documentation [1]
Load the boot partition by label instead of by index
[1] https://source.android.com/devices/bootloader/partitions
Signed-off-by: Guillaume La Roque <mkorpershoek@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Right now, when running fastboot we use a hard-coded "0" for the
device number.
Use the Kconfig option named CONFIG_FASTBOOT_USB_DEV instead.
Signed-off-by: Guillaume La Roque <mkorpershoek@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
both lines seem to be joined together which is not the case for the
meson64.h EXTRA_ENV_SETTINGS.
Add a newline for consistency.
Signed-off-by: Guillaume La Roque <mkorpershoek@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This actually does nothing but is defined by a few dozen boards. Drop it,
so we can define a real one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and
CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less
than a year away.
Also we want to have a CONFIG_I2C for U-Boot proper just like we have
CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules.
Rename this symbol so it is clear it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
make possible to load simple compressed linux kernel for meson64
Signed-off-by: Artem Lapkin <art@khadas.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The common J7 specific start_non_linux_remote_cores() override function
implements the logic to load and boot the Main R5FSS Core0 from R5 SPL.
This won't be supported any more for either J721E or J7200 after the R5
SPL rearchitecture for the System Firmware split into TI Foundation
Security (TIFS) and Device Management (DM) firmwares. So, cleanup the
corresponding code and the related SPL env variables.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726211311.5977-3-s-anna@ti.com
The Main R5FSS Core0 on J721E SoCs is originally booted from R5 SPL
itself to achieve certain product-level early-boot metrics. This is
no longer supported after the R5 SPL re-architecture (support merged
for v2021.10-rc1). Move the booting of this core altogether from R5
SPL to A72 U-Boot.
The env variables are left as is for now, and will be cleaned up
in a subsequent patch.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726211311.5977-2-s-anna@ti.com
Kconfig symbols for SYS_MMC_ENV_DEV and SYS_MMC_ENV_PART have been added by
commit 7d08077334. Therefore, move the
definitions of configs to corresponding board defconfig files and enable
configs to save env in eMMC.
Also enable config for FAT write in U-Boot.
Fixes: 33b7258947 ("board: ti: am64x: Add board support for am64x evm")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726152807.22991-5-a-govindraju@ti.com
MAIN CPSW0 requires the PHY to be powered on and reset for QSGMII
operation. Add a env variable to configure driving "0" on ENET_EXP_PWRDN
controlled by GPIO EXPANDER2 (I2C Addr: 0x22), PIN: 17 and driving "1"
on ENET_EXP_RESETZ controlled by GPIO EXPANDER2 (I2C Addr: 0x22),
PIN: 18.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-18-kishon@ti.com
Add kernel_comp_addr_r, kernel_comp_size env variables for zynqmp and
versal to be able to use the compressed kernel Image(.gz,.bz2,.lzma,.lzo)
using booti command.
Signed-off-by: Raju Kumar Pothuraju <raju.kumar-pothuraju@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is default value which had been converted by commit 432e398068
("include/configs: drop default definitions of CONFIG_SYS_PBSIZE"). That's
why also remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for loading
images")' changed the way buffer allocation worked for SPL to a more
flexible method.
For xilinx zynqmp the 1MB buffer is not necessarily enough when dealing
with complex fit images (e.g. containing FPGA/TF-A/OP-TEE/U-Boot
proper), which can easily reach up to 10MB, so increase the default
CONFIG_SYS_SPL_MALLOC_SIZE size to 16MB to cover more advanced
scenarios.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The DragonBoard 410c has proprietary firmware from Qualcomm that
reserves 8 MiB of memory for tz/smem/hyp/rmtfs/rfsa from 0x86000000
to 0x86800000. I'm not aware of any ATF (ARM Trusted Firmware) port
for DB410c that would reserve 30 MiB of memory at the end of RAM.
I suspect the comment might have been copied from hikey.h which has
a very similar comment (and which actually does have an ATF port).
Reducing the memory size just prevents U-Boot from using the end of
the RAM, not the reserved region inbetween. Therefore we might as well
display the correct DRAM size (1 GiB) instead of strange 986 MiB.
Fixes: 626f048bbc ("board: Add Qualcomm Dragonboard 410C support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
At the moment the U-Boot port for the DragonBoard 410c is designed
to be loaded as an Android boot image after Qualcomm's Little Kernel (LK)
bootloader. This is simple to set up but LK is redundant in this case,
since everything done by LK can be also done directly by U-Boot.
Dropping LK entirely has at least the following advantages:
- Easier installation/board code (no need for Android boot images)
- (Slightly) faster boot
- Boot directly in 64-bit without a round trip to 32-bit for LK
So far this was not possible yet because of unsolved problems:
1. Signing tool: The firmware expects a "signed" ELF image with extra
(Qualcomm-specific) ELF headers, usually used for secure boot.
The DragonBoard 410c does not have secure boot by default but the
extra ELF headers are still required.
2. PSCI bug: There seems to be a bug in the PSCI implementation
(part of the TrustZone/tz firmware) that causes all other CPU cores
to be started in 32-bit mode if LK is missing in the boot chain.
This causes Linux to hang early during boot.
There is a solution for both problems now:
1. qtestsign (https://github.com/msm8916-mainline/qtestsign)
can be used as a "signing" tool for U-Boot and other firmware.
2. A workaround for the "PSCI bug" is to execute the TZ syscall when
entering U-Boot. That way PSCI is made aware of the 64-bit switch
and starts all other CPU cores in 64-bit mode as well.
Simplify the dragonboard410c board by removing all the extra code that
is only used to build an Android boot image that can be loaded by LK.
This allows dropping the custom linker script, special image magic,
as well as most of the special build/installation instructions.
CONFIG_REMAKE_ELF is used to build a new ELF image that has both U-Boot
and the appended DTB combined. The resulting u-boot.elf can then be
passed to the "signing" tool (e.g. qtestsign).
The PSCI workaround is placed in the "boot0" hook that is enabled
with CONFIG_ENABLE_ARM_SOC_BOOT0_HOOK. The extra check for EL1 allows
compatibility with custom firmware that enters U-Boot in EL2 or EL3,
e.g. qhypstub (https://github.com/msm8916-mainline/qhypstub).
As a first step these changes apply only to DragonBoard410c.
Similar changes could likely also work for the DragonBoard 820c.
Note that removing LK wouldn't be possible that easily without a lot of
work already done three years ago by Ramon Fried. A lot of missing
initialization, pinctrl etc was already added back then even though
it was not strictly needed yet.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Since MTD partitions are based on the devicetree name,
remove unneeded mtdparts settings and update DFU setting.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
CONFIG_NET_MULTI has been removed long time ago by commit 795428fc67
("net: remove CONFIG_NET_MULTI") but 4 boards were added later which wasn't
found. The patch is removing this reference from 4 boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The ARM Juno boards can be used as somewhat decent machines to run
off-the-shelf distributions, with USB, SATA, GBit Ethernet and 8GB of
DRAM.
With stable DTs in the board's NOR flash this would work really nicely,
however the default boot command is to fetch a kernel and an initrd from
the on-board NOR flash, which sounds somewhat embedded.
Include the config_distro_bootcmd.h header and define the available
devices (starting with USB, to catch USB installer sticks) to make
distributions and UEFI work out of the box.
The NOR flash kernel functionality is still preserved as the last
resort, should all other methods fail.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Set MC Firmware size in read commands in
env to 2MB.
Update DDR Memory read address for MC firmware to
0x80a00000 and MC DPC address to 0x80e00000.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Set MC Firmware size in read commands in
env to 2MB.
Update DDR Memory read address for MC firmware to
0x80a00000 and MC DPC address to 0x80e00000.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Set MC Firmware size in read commands in
env to 2MB.
Update DDR Memory read address for MC firmware to
0x80a00000 and MC DPC address to 0x80e00000.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Set MC Firmware size in read commands in
env to 2MB.
Update DDR Memory read address for MC firmware to
0x80a00000 and MC DPC address to 0x80e00000.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Marvell SheevaPlug: Convert Ethernet and SATA to Driver Model (Tony)
- Zyxel NSA310S NAS: Convert to Driver Model (Tony)
- Turris_omnia: Add `u-boot-env` NOR partition (Marek)
- Turris_omnia: Fixup MTD partitions in Linux' DTB (Marek)
- Espressobin: Enable 'mtd' command and define SPI NOR partitions (Pali)
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
# Conflicts:
# arch/arm/mach-omap2/am33xx/Kconfig
U-Boot now supports parsing SPI NOR partitions from Device Tree. So enable
'mtd' command support for Espressobin board and define partition layout in
U-Boot Espressobin DTS file. Access to SPI NOR via 'sf' command is old
method and 'mtd' command is now preferred variant.
From include file remove '#define CONFIG_MTD_PARTITIONS' as this option is
now defined and enabled in defconfig file. This change is required to fix
compile error:
CC arch/arm/lib/asm-offsets.s
In file included from include/config.h:4,
from include/common.h:16,
from lib/asm-offsets.c:14:
include/configs/mvebu_armada-37xx.h:63: warning: "CONFIG_MTD_PARTITIONS" redefined
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
In file included from ././include/linux/kconfig.h:4,
from <command-line>:
include/generated/autoconf.h:44: note: this is the location of the previous definition
#define CONFIG_MTD_PARTITIONS 1
After enabling support for mtd command, output from 'mtd list' on
Espressobin board is:
=> mtd list
List of MTD devices:
* w25q32dw
- device: spi-flash@0
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/internal-regs/spi@10600/spi-flash@0
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000400000 : "w25q32dw"
- 0x000000000000-0x0000003f0000 : "firmware"
- 0x0000003f0000-0x000000400000 : "u-boot-env"
=>
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
As the logic here is only used when we have a USB host controller, test
on CONFIG_USB_HOST rather than CONFIG_USB in general. This lets us move
towards using CONFIG_USB only as a menu symbol to say that we have some
form of USB, and then USB_HOST or USB_GADGET depending on the role that
USB plays within the build.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reuse the common logic to allow for BOOT_TARGET_DEVICES to list USB as a
possibility if we're building for a platform that will have USB but not
if we don't, so that we don't hit the link-time check for trying to have
USB boot on a non-USB system.
Acked-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These USB defines do not change the build as there is no USB support
enabled currently.
Cc: Ian Ray <ian.ray@ge.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the variable used by PXE command for fdtoverlays support
since the commit 69076dff22 ("cmd: pxe: add support for FDT overlays").
Reused the unused "splashimage" address as CONFIG_SPLASH_SOURCE and
CONFIG_VIDEO_LOGO are not activated and U-Boot display the "BACKGROUND"
image found in extlinux.conf to manage splashscreen on stm32mp1 boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
By default bootmenu is loaded only from eMMC. After this change U-Boot
first tries to load bootmenu from uSD card and if it fails then fallback to
eMMC. People want to boot alternative OS from removable uSD without need to
modify eMMC content. So this backward compatible change allows it.
Part of this change is also optimization of trymmc* macros so they can be
used in preboot macro for loading bootmenu.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210618132704.32066-2-pali@kernel.org
Enable U-Boot bootz command and update env scripts to try loading also
zImage file and to try booting via bootz command.
Update also lowlevel_init.S code for checking validity of zImage magic to
correctly relocate kernel in zImage format.
This change allows U-Boot to directly boot Linux kernel without need for
converting kernel image into U-Boot uImage format.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210618132704.32066-1-pali@kernel.org
Swap out the TI-centric "envboot" logic for the generic distro_bootcmd
logic for the bootcmd we run before trying to do something more complex
involving additional firmware, etc.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210713141139.15183-1-trini@konsulko.com
The usbtty functionality is not currently used on these two platforms,
disable it.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210708014348.4010-1-trini@konsulko.com
Swap out the TI-centric "envboot" logic for the generic distro_bootcmd
logic for the bootcmd we run before trying to do something more complex
involving additional firmware, etc.
Cc: Lokesh Vutla <lokeshvutla@ti.com> (maintainer:J721E BOARD)
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701142743.26190-1-trini@konsulko.com
Remove the environment support for various legacy boot methods. With
this, we will now default to booting any distribution that follows the
generic distro boot framework and no longer attempt to boot various
legacy (to this SoC) scripts/etc. Note that if we do not find anything
here we will continue to try and Android methods and will start by
trying fastboot.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701132612.7559-3-trini@konsulko.com
This include file is only used by ti_omap5_common.h. Further, the move
is towards using the generic distro boot framework and not this set of
macros. Start by moving all of the contents in directly to where they
are used.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701132612.7559-2-trini@konsulko.com
Remove the environment support for various legacy boot methods. With
this, we will now default to booting any distribution that follows the
generic distro boot framework and no longer attempt to boot various
legacy (to this SoC) scripts/etc.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701132612.7559-1-trini@konsulko.com
Remove the environment support for various legacy boot methods. With
this, we will now default to booting any distribution that follows the
generic distro boot framework and no longer attempt to boot various
legacy (to this SoC) scripts/etc.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210610230147.22475-1-trini@konsulko.com
autoload: if set to "no" then rarpb, bootp or dhcp commands will
just perform a configuration lookup from the BOOTP / DHCP server,
but not try to load any image using TFTP
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210611161350.2141-8-Gireesh.Hiremath@in.bosch.com
The U-Boot "stemmy" board is mainly intended to simplify booting
mainline Linux on various smartphones from Samsung based on ST-Ericsson
Ux500. While the mainline kernel is working great, there are still some
features missing there. In particular, it is currently not possible to
charge the battery when using the mainline kernel.
This means that it is still necessary to boot the downstream/vendor
kernel from Samsung sometimes to charge the device. That kernel is
ancient, still uses board files + ATAGS instead of device trees and
relies on a strange very long kernel command line hardcoded in the
Samsung bootloader.
Actually, since mainline is booted with device trees there is a very
simple way to make the old downstream kernel work as well: We can
simply take most of the ATAGS passed to U-Boot from the Samsung
bootloader and copy them as-is when booting a kernel without device
tree. That way the long command line and other needed ATAGS are copied
as-is without having to bother with them.
The only exception is the ATAG_INITRD - since the initrd is loaded
by U-Boot, the atag for that should be generated in U-Boot so it points
to the correct address. All other ATAGS are copied as-is and not
generated in U-Boot.
Also use the chance and provide a serial# for U-Boot by parsing the
ATAG_SERIAL that is also passed by the Samsung bootloader.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
At the moment the "stemmy" board attempts to detect the RAM size with
a simple memory test (get_ram_size()). Unfortunately, this does not work
correctly for devices with 768 MiB RAM (e.g. Samsung Galaxy Ace 2
(GT-I8160), "codina"). Reading/writing memory after the 768 MiB RAM
succeeds but actually overwrites some earlier parts of the memory.
For U-Boot this does not result in any major problems, but on Linux
this will eventually lead to strange crashes because of the memory
corruption.
Since the "stemmy" U-Boot port is designed to be chainloaded from
the original Samsung bootloader, the most reliable way to get the
available amount of RAM is to look at the ATAGS passed by the Samsung
bootloader. Fortunately, the header used to generate ATAGS in U-Boot
(asm/setup.h) can also be easily used to parse them.
Also clarify and simplify stemmy.h a bit to make it more clear where
some of the magic values in there are actually coming from.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Enable support for the fec ethernet on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
On the Yocto image there is a single partition and the kernel
and dtb are present in the 'boot' directory.
Change it accordingly so that the board can boot the Yocto
image by default.
Use the generic 'load' command instead, which is able to
read from an ext4 partition.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Extend CONFIG_SYS_BAUDRATE_TABLE and include all standard baudrates and
also nonstandard up to the 6 MBaud. U-Boot's A3720 UART driver can use
baudrates from 300 Baud to 6 MBaud.
This changes all A3720 boards, since all of them include either
mvebu_armada-37xx.h or turris_mox.h config file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
While this platform has not yet been converted, there is active efforts
to do so. Keep the platform for now.
This reverts commit aa697e6904.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
also the last SPEAR3XX platform, remove that symbol as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Gerald Kerma <dreagle@doukki.net>
Cc: Tony Dinh <mibodhi@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Ajay Bhargav <contact@8051projects.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it.
This is also the last PL010_SERIAL using board, so remove those
references.
Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8315 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8568 platform, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and are
also missing conversion to CONFIG_DM. Remove them.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is all of the CONFIG_M548x platforms as well,
remove that code.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
Convert the CONFIG_SYS_I2C_LPC32XX configuration symbol from an include
directive to a Kconfig value.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic support for running U-Boot on the Embedded Artists LPC3250
Developer's Kit v2 board by launching U-Boot from the board's s1l loader
(which comes pre-installed on the board).
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
There's nothing special or unique to the lpc32xx that requires its own config
parameter for specifying the console uart index. Therefore instead of using
the lpc32xx-specific CONFIG_SYS_LPC32XX_UART include parameter, use the
already-available CONFIG_CONS_INDEX from Kconfig.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable EFI capsule update support. With the EFI capsule update,
you can update U-Boot, TF-A and OP-TEE. TF-A and OP-TEE are
usually combined as a FIP binary, but if the binary is bigger
than 480KB, you have to modify FIP header, split the OP-TEE
and stores the OP-TEE binary in the different place. This
configuration supports both cases.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.
For more information, see this page;
https://www.96boards.org/product/developerbox/
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add initial support for the PCB description EEPROM for SiFive HiFive
Unmatched boards.
This implementation is refactored based on Paul Walmsley's porting and
adopt the suggestions from David Abdurachmanov.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This patch adds openpiton-riscv64 SOC support. In particular, this
board supports a standard bootflow through zsbl->u-boot SPL->
opensbi->u-boot proper->Linux. There are separate defconfigs for
building u-boot SPL and u-boot proper
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Set default fdtfile names for unleashed and unmatched boards, as used
in the upstream Linux kernel. This allows sysboot command to find and
load appropriate dtb for the matching kernel from universal stock
Ubuntu RISC-V rootfs images based on fdtdir setting in extlinux.conf.
Signed-off-by: Dimitri John Ledkov <dimitri.ledkov@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
cc: Paul Walmsley <paul.walmsley@sifive.com>
cc: Palmer Dabbelt <palmer@dabbelt.com>
cc: Anup Patel <anup.patel@wdc.com>
cc: Atish Patra <atish.patra@wdc.com>
cc: Pragnesh Patel <pragnesh.patel@sifive.com>
cc: Green Wan <green.wan@sifive.com>
Init GICv3 for V3U Falcon in early phase
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add board code for the R8A779A0 V3U Falcon board.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - various small rebase fixes and clean ups
Based on the comment in socfpga_soc64_common.h, the intention is for
CONFIG_SYS_MEM_RESERVE_SECURE to be unused. However, in the code we do:
...
and that will evaluate to true. This leads to unwanted code being
compiled. Further, as CONFIG_SYS_MEM_RESERVE_SECURE has not been
migrated to Kconfig, this leads to a mismatch in the size of gd
depending on if we have or have not also had <configs/BOARD.h> also
included yet.
Remove the define as it's not needed.
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Chee Hong Ang <chee.hong.ang@intel.com>
Cc: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
RK3568 is a high-performance and low power quad-core application
processor designed for personal mobile internet device and AIoT
equipments.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
fdtoverlay (pxe_utils) require define fdtoverlay_addr_r env variable
for example sunxi-common.h meson64.h already have it.
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDLD78cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLhSB/0UqOd+Ujf2meiHU9yr
oOOCLxVTjTUfIZKLad/zwlj2Xqzsjs6XMawC95BgouvkQLmj/gwerRWcZPg9l7/X
hvb9VJi+iJoLRRpBPbeF3bMb92kCE+YZodFXyutlcY+Z0ZB9755zoVgR6ccKfksd
Xp2y8AFptfYQNZ1l0yb3lhm1261CldWALrGTjRpY2hQ8nEMbV8z6WUB1hAF9CECa
PGbKaiqm9OdktwHsLy4cYFFCuzkykn6T3P6ODineP7IxgEgZKTfJClSTFGY9S0GQ
kwd7K/7j0W3rI5NPknB+Fb4IFAaTs/oozR+5ml7j+2S3G5GXjSGx8zaSOmOZvpP3
KxwN
=/I5V
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for the 2021.10 cycle:
This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs
connected to MAC1 and MAC2. The second Aquantia PHY is located at a
different address on the MDIO bus compared to rev C (0x8 instead of 0x1).
Fix-up the Linux device tree to update the PHY address for the second
Aquantia PHY on boards revisions D and up. Also rename the PHY node to
reflect the changes.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
A system clock of 66MHz was chosen for the pg-wcom-ls102xa.
Compared to the Evalboard, this corresponds to a reduction of 1/3.
The system counter clock should have been reduced accordingly,
but that was not the case, so we had a system time that was
1/3 behind the real time.
This patch corrects the system counter clock to
8.333MHz = 66.667MHz / 8.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to improve power consumption ls102x allows to disable peripherals
that are not in use.
This patch follows SELI8 HW design description and disables peripherals
that are not in use in our designs, the same configuration is applicable
and for EXPU1.
This patch uses available hwconfig option for updating ls102x device
disable configuration.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The default behavior in the latest u-boot revisions is to rotate the
active net device to the next available if the requested link is not
established.
For our ls102x based devices this would mean that if active debug net
device is not available, u-boot will rotate and set the next net device
that is one of the estar adapters.
To return from this situation manual action to set correct ethact
adapter will be needed and this can be annoying when working in
debug mode.
Setting ethrotate=no will disable net adapter rotation and will make sure
that the primary adapter is always used.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In our designs we reserve PRAM area at the end of the RAM, and in order
this area to be visible and taken into account by the u-boot memory mgmt
CONFIG_PRAM has to be defined.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
From production view this is standard test executed during production on
all linux based foxmc cards.
On CENT2 HW defined memory region is zero means that some DDR accesses are
done by memory_post_dataline and memory_post_addrline but pattern tests
are skipped that's why mem_regions is fast there.
On ls102x for the complete DDR region of 1GiB memory_regions_post_test
takes approx. 4min and this is too much for production, so this patch
defines only 1MiB region as compromise.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
is used instead.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Michael Walle <michael@walle.cc> [for kontron-sl28]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards, according to the schematic and per the board I own, use an
M24256-BWDW6TP I2C EEPROM which requires two address bytes.
This fixes the 'mac' command which is used to program, among other
things, the MAC addresses for the ethernet interfaces on the board.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports Falcon boot support for Microchip SAMA5D3 Xplained,
tested on raw MMC, and on raw NAND.
spl_start_uboot() is has the simplest possible implementation.
It doesn't test the environment because enabling environment support
currently causes the SPL to exceed its maximum size (64 KiB).
It doesn't check the serial for incoming characters either because
this functionality currently doesn't seem to work from the SPL
on this board.
Settings for Falcon boot from at FAT partition are also added to
avoid compile failures when CONFIG_SPL_OS_BOOT is enabled, but this
particular case is currently not functional as adding FAT and
partition support cause the SPL to be too big again.
Signed-off-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Add default fdtfile environment variable with value
marvell/armada-3720-turris-mox.dtb.
This can be useful for some boot scenarios.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable config options required to add support for USB Mass storage boot,
USB DFU boot, host and device modes in U-Boot.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-11-a-govindraju@ti.com
For USB DFU boot mode there is a limitation on the load address of boot
images that they have to be less than 0x70001000. Therefore, move the
SPL_TEXT_BASE address to 0x70000000.
Currently ATF is being loaded at 0x70000000, if the SPL is being loaded at
0x70000000 then ATF would overwrite SPL image when loaded. Therefore, move
the location of ATF to a latter location in SRAM, past the SPL image. Also
rearrange the EEPROM and BSS data on top of ATF.
Given below is the placement of various data sections in SRAM
┌──────────────────────────────────────┐0x70000000
│ │
│ │
│ │
│ SPL IMAGE (Max size 1.5 MB) │
│ │
│ │
│ │
├──────────────────────────────────────┤0x7017FFFF
│ │
│ SPL STACK │
│ │
├──────────────────────────────────────┤0x70192727
│ GLOBAL DATA(216 B) │
├──────────────────────────────────────┤0x701927FF
│ │
│ INITIAL HEAP (32 KB) │
│ │
├──────────────────────────────────────┤0x7019A7FF
│ │
│ BSS (20 KB) │
├──────────────────────────────────────┤0x7019F7FF
│ EEPROM DATA (2 KB) │
├──────────────────────────────────────┤0x7019FFFF
│ │
│ │
│ ATF (123 KB) │
│ │
│ │
├──────────────────────────────────────┤0x701BEBFB
│ BOOT PARAMETER INDEX TABLE (5124 B)│
├──────────────────────────────────────┤0x701BFFFF
│ │
│SYSFW FIREWALLED DUE TO A BUG (128 KB)│
│ │
├──────────────────────────────────────┤0x701DFFFF
│ │
│ DMSC CODE AREA (128 KB) │
│ │
└──────────────────────────────────────┘0x701FFFFF
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-9-a-govindraju@ti.com
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Supported boot device types in iMX8MN: MMC, DHCP.
Add DISTRO_DEFAULTS config option and include the distro boot command
header file to enable full support of distro boot on i.MX8M Nano EVK (both
DDR and LPDDR derivatives).
Drop previous environment, which was targeting customized boot commands and
boot order.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.
Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.
Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
Uncompressed aarch64 kernel Image are rather large, increase the bootm
size limit to 64 MiB to cater for that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Currently the config options CONFIG_SYS_DFU_DATA_BUF_SIZE and
CONFIG_SYS_DFU_MAX_FILE_SIZE are being set in include/configs/<board>.h
files and also in <board_name>_defconfig files without a Kconfig option. It
is easier for users to set these configs in defconfig files than in config
header files as they are a part of the source code.
Add Kconfig symbols, and update the defconfigs by using tools/moveconfig.py
script.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
TFTP transfer size can be used to re-size the TFTP progress bar on
single line based on the server reported file size. The support for
this has been around from 2019, but it was never converted to proper
Kconfig.
While adding this new Kconfig, enable it by default for OMAP2+ and K3
devices also.
Signed-off-by: Tero Kristo <kristo@kernel.org>
Make it possible to invoke rescue boot from U-Boot console, without
having to press the factory reset button. This is needed when accessing
the device remotely, for example.
Achieve this by putting rescue command into `bootcmd_rescue` default
environment variable and setting some distroboot environment variables
to their default values when the factory button is pressed.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Remove qemu_mips boards because DM migration doesn't make sense.
The board support for qemu_mips is already marked as deprecated
in Qemu in favour of the Malta board. Also qemu_mips support
has been removed from Linux a long time ago.
The official replacement is the Malta board. The same Malta U-Boot
image can be used with Qemu and on physical hardware.
All combinations of Big Endian and Little Endian as well as 32 bit
and 64 bit are supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Increase the BOOTM_LEN to 32M . This would allow a bigger kernel image to be
booted, for example the multi_v7_defconfig.
Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
resetting ...
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We just need to initialize all the clocks pre-reloc. The clock driver
creates a bunch of devices, so we need to increase the pre-reloc malloc
arena.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Enable CONFIG_DM_ETH in configs/pm9263_defconfig
Drop legacy initialization in board/ronetix/pm9263.c
Remove network related setting from include/configs/pm9263.h
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Now that single defconfig can be used for booting AM64 EVM and SK,
default device tree will not work for selecting dtb for kernel.
Update the env to select right dtb based on eeprom.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Current BSS allocation of SPL is as below:
size spl/u-boot-spl
text data bss dec hex filename
144572 5484 1752 151808 25100 spl/u-boot-spl
But 20KB is allocated currently for BSS. Reduce it to 4KB and
save some space for stack.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Prevent shell access on boot failure by entering an infinite
loop.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Minor cosmetic changes to unify `CONFIG_EXTRA_ENV_SETTINGS'
indentation between Bx50v3 and PPD to make comparison and
review easier and simplify the default boot command.
Signed-off-by: Ian Ray Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Enable EFI capsule update features to be enabled by default also with all
dfu valid options for ZynqMP.
This feature was tested on Xilinx ZynqMP zcu104 board with defining
dfu_alt_info="mmc 0:1=boot.bin fat 0 1;u-boot.itb fat 0 1"
and
dfu_alt_info="sf 0:0=boot.bin raw 0 0x50000;u-boot.itb raw 0x80000
0x500000".
There is a need to increase malloc size for getting dfu mmc to work.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAmCEf04ACgkQKPlOlyTy
XBj2Aw//SxPX48XynT979cMIOoylO6Rs1saWtQr32YmycWnGC0/wvFNPU/kjNP/a
jinOxvY2TSBNqToSuCDZxGXyijMIdAnWVCQCUXmah7bZ+GtiYWR0SHNO0TQ+qrBW
06CC7hgQQqQswGClJe4njwTyVIzTQvyo/UdjS6RWggDZPsnGpyMlR5O56ZCNNH8o
1XFCG8hSrQBRO38RpXciGS3dFeaqOQy96K9M5pellf9Fh5a+jHyAmK8Z/0R+T6cG
+PoNh6qZAsXFj0PVuvu0CaXFHpP+fhdA4kEwt64PJCe8D3x7d05COuN0bL+e6D6u
E4cSnkjmzNgYvoi4YAGaQN9f4PKPSMHuYf7YdIBFCQQ8OtxNXpUHOg0zr4SRnq/C
ypq285f2O7Aq+3t0BrC7jTjo+Y2PzVIUR8MXpvh698ZSdJnqOlJf0y5tRwdhf/+k
gh+rT7mWIOoRRWpb6qHMUr5gnparl0gOykspMlQ2NKB+kfmC4RP2pYxQFp82TFIq
ZMUaXer2/g5dVptEhTU0vBsTrk7s/u239WtwyXpOCdoM6sI/FoMoiCoQoD2isKP6
mUv/iwTpfNTtQnx5MM2Xsu+8pzcXjaVeoMaNcI55jZ2QTCoMAFA6odYTk+GHS3Vx
Yt3TLrH6O46PXNSULROkmTR4RgiDHcGCX/HGTKkcA/+X9GDjjNc=
=JwRN
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2021-04-24' of https://source.denx.de/u-boot/custodians/u-boot-mips
- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
Add support for usb dfu & thor to distro boot on zynq platform.
Add 60s timeout of dfu-utils to start transaction. Remove
DFU_ALT_INFO_RAM as we use bootcmd_usb_dfu instead of dfu_ram.
Remove DFU_ALT_INFO_MMC as part of distro boot cleanup.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change "dfu_usb" to "usb_dfu" for better representation and change
required macros. Add 60s timeout of dfu-utils to start transaction.
Add support for usb thor to distro boot. Remove DFU_ALT_INFO_RAM
as we use bootcmd_usb_dfu instead of dfu_ram.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dfu ram info is wired in connection to Linux kernel and certain setup.
We should change this to be more generic as others command. That's why
using boot via script is the way to go.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In usb boot mode distro boot should select usb device as primary boot
device instead of usb host. So make usb dfu as primary boot device. But do
not list it in boot_targets as fallback option because it is not classic
mode for booting. Using 60s timeout by default should be enough time for
dfu-utils to start transaction. In case none needs this please change
timeout value in the command or disable CONFIG_DFU_TIMEOUT.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
So far we were defining a somewhat confusing PHYS_SDRAM_1_SIZE variable,
which originally was only used for setting the memtest boundaries. This
definition in highbank.h has been removed about a year ago (moved to
Kconfig), so we also don't need the hard-coded size definition any longer.
Get rid of the misleading memory size definition, which was actually wrong
anyway (it's 4088 MB for those machines with just 4GB of DRAM).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
All Calxeda machines are actually a poster book example of device tree
usage: the DT is loaded from flash by the management processor into
DRAM, the memory node is populated with the detected DRAM size and this
DT is then handed over to the kernel.
So it's a shame that U-Boot didn't participate in this chain, but
fortunately this is easy to fix:
Define CONFIG_OF_CONTROL and CONFIG_OF_BOARD, and provide a trivial
function to tell U-Boot about the (fixed) location of the DTB in DRAM.
Then enable DM_SERIAL, to let the PL011 driver pick up the UART platform
data from the DT. Also define AHCI, to bring this driver into the driver
model world as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far on Highbank/Midway machines U-Boot only ever uses 512MB of DRAM,
even though the machines have typically 4GB and 8GB, respectively.
That means that so far we didn't need an extra limit for placing the DTB
and initrd, as the 512MB are lower than the kernel's limit ("lowmem",
typically 768MB).
With U-Boot now needing to learn about the actual memory size (to
correctly populate the EFI memory map), it might relocate fdt and initrd
to the end of DRAM, which is out of reach of the kernel.
So add limiting values to the fdt_high and initrd_high environment
variables, to prevent U-Boot from using too high addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_SUPPORT_RAW_INITRD out of the octeontx_common header
and into the defconfig files.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a patchset which makes away with the .bind() controller indexing
workaround which was broken since before v2021.04, and then adds PHY
support and MX8M support on top of that. Better add it into the release
early to get as much testing as possible done, because this really does
a lot of changes to the ehci-mx6 driver.
Enable USB host support on MX8MM Verdin.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The "booti" command to load arm64 Linux kernels supports automatic
decompression of zipped kernel images, but relies on some environment
variables to point to usable buffer RAM.
Add those variables and let them point to some default values, that
should cover most use-cases.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit 69076dff22 ("cmd: pxe: add support for FDT overlays") added
support for loading DT overlay files to PXE boot. However, it needs
additional environment variable which points to memory location which
can be used to temporary store overlay data.
Add it and in the process unify alignment using spaces and fix comment.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However, this call is missing for ls1012a boards. As a result EFI
boot doesn’t work. Fix this issue by removing custom definition of
scan_dev_for_boot and use the default definition instead.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With all preparations in place, switch over to DM_SERIAL.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The DSA sandbox driver is used for unit testing the DSA class code.
It implements a simple 2 port switch plus 1 CPU port, and uses a
very simple tag to identify the ports.
The DSA sandbox device is connected via CPU port to a regular Ethernet
sandbox device, called 'dsa-test-eth, managed by the existing eth
sandbox driver. The 'dsa-test-eth' is not intended for testing the
eth class code however, but it is used to emulate traffic through the
'lan0' and 'lan1' front pannel switch ports. To achieve this the dsa
sandbox driver registers a tx handler for the 'dsa-test-eth' device.
The switch ports, labeled as 'lan0' and 'lan1', are also registered
as eth devices by the dsa class code this time. So pinging through
these switch ports is as easy as:
=> setenv ethact lan0
=> ping 1.2.3.5
Unit tests for the dsa class code were also added. The 'dsa_probe'
test exercises most API functions from dsa.h. The 'dsa' unit test
simply exercises ARP/ICMP traffic through the two switch ports,
including tag injection and extraction, with the help of the dsa
sandbox driver.
I took care to minimize the impact on the existing eth unit tests,
though some adjustments needed to be made with the addition of
extra eth interfaces used by the dsa unit tests. The additional eth
interfaces also require MAC addresses, these have been added to the
sandbox default environment.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20210216224804.3355044-5-olteanv@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.
It is based on NXP LS1021 SoC and it provides following interfaces:
- IFC interface for NOR, NAND and external FPGA's
- 1 x RGMII ETH for debug purposes
- 2 x SGMII ETH for management communication via back-plane
- 1 x uQE HDLC for management communication via back-plane
- 1 x I2C for peripheral devices
- 1 x SPI for peripheral devices
- 1 x UART for debug logging
It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It's an old bringup board with out upstream Linux or L4T support
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Add power_max77696_init() function.
Since warp doesn't support DM, the keeping its code in board file is
better than maintainig the file of driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. It is also the only ARCH_T2081 board so remove that support
as well.
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <linuxfae@technexion.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Thomas Weber <weber@corscience.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM by the deadline.
Remove them.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Erik van Luijk <evanluijk@interact.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The mvsata_ide driver was due for DM conversion by v2019.07. As that
has long passed, remove the driver and disable it in the boards which
had enabled it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. In order to
convert to using the DWC SATA driver under DM further migrations are
required.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
-----BEGIN PGP SIGNATURE-----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=4VxR
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210409' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
A now removed comment promises to "limit SYSRAM usage to first 128 KB".
This would imply that only SYSRAM from 0x2ffc0000 - 0x2ffe0000 would be
used. This is not what happens at all.
First, SPL_MAX_SIZE is referenced from SPL_TEXT_BASE, which on all
existing configs is set to 0x2ffc2500, not SYSRAM_BASE (0x2ffc0000).
Some of it is in the first 128 KiB and some of it is in the second
128 KiB chunk of SYSRAM.
Second, SPL_MAX_SIZE, does not restrict the BSS size. While a valiant
attempt is made via SPL_BSS_MAX_SIZE, the value of 0x00100000 is much
larger than SYSRAM, and doesn't account for the non-BSS sections.
Because we're putting the .text and .bss in the same boat, the correct
way to limit them together is via SPL_MAX_FOOTPRINT. With the current
SPL_TEXT_BASE, we couldn't limit even a very basic SPL to the first
128 KiB, and there is no technical reason to do so. Because of this,
simply allow the SPL to use all SYSRAM.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
CONFIG_SPL_BSS_START_ADDR is only used on a few mach- linker scripts.
stm32mp1 uses the generic script under arch/arm/cpu/u-boot-spl.lds,
which does not make use of this definition.
The SPL BSS starts in SRAM, right after .text, .rodata, .data, and
.u_boot_list. A very short version of the STM32MP1 memory map is:
* SYSRAM: 2ffc0000 - 30000000 <- all of SPL is here
* DRAM: c0000000+
0xC0200000 is a DRAM address, and has nothing to do with SPL. It is
just very misleading to have it next to CONFIG_SPL_BSS_MAX_SIZE, or to
have it at all.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for
loading images"), FIT images must be malloc()'d before being loaded.
The old size of 1 MiB is suitable for FIT images with u-boot and an
FDT, but something containing a linux kernel is almost sure to fail.
It's safe to extend malloc all the way to 0xc2000000, but no further.
Linux likes to be loaded at 0xc2000000, so we use that as our cutoff
point. This gives us 29 MiB of malloc() space, which suited for more
complex FIT images including several DTBs, kernel, and OP-TEE images.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
All these files are add for support rt-thread art-pi board
- add board/st/stm32h750-art-pi, defconfig, header support for u-boot
for more information about art-pi, please goto:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enabled "fsl,legacy-bch-geometry" in U-Boot device tree overlay
to match the legacy BCH geometry layout, which mainline Linux
applies when "fsl,use-minimum-ecc" is not specified in the device
tree.
Reinstated SYS_NAND_ONFI_DETECTION, which when disabled, masked
the mismatch on SOMs with Winbond NAND flash chips.
Signed-off-by: Niel Fourie <lusus@denx.de>
Convert the UDOO board to use DM_ETH.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block, DM MMC and DM SATA support on iMX6 Udoo
convert board code to match the DM support.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since Toradex provides the full set of overlays for Linux kernel
for display interfaces for both Apalis iMX6Q and Colibri iMX6DL
modules, the video= settings are obsolete. Remove them.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
All the other boards have tdxargs specified for setting manual kernel
command-line arguments. Add them also to NAND-based boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for loading images")'
changed the way buffer allocation worked for SPL to a more flexible
method.
For venice this caused breakage that is resolved by increasing the size
of CONFIG_SYS_SPL_MALLOC_SIZE as the current FIT slighly exceeds 512KiB.
Additionally remove the unnecessary comment on CONFIG_SPL_BSS_MAX_SIZE
and CONFIG_SYS_SPL_MALLOC_SIZE as the size is obvious from the define.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model for MTD and NAND support allowing us to remove
the iomux, init, and most of the static configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable dm support for USB (which also requires dm support for fixed
regulators used for vbus enable) and remove usb iomux which is no
longer needed.
We can remove the handling of otgpwr_en gpio as this is defined in
dt as usbotg vbus-supply but we need to keep the handling of
USB_HUB_RST# for boards that have a USB HUB as that isn't defined in
the dt's currently.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
In preparation to add SiFive Unmatched board support, let's rename
the existing fu540 board to unleashed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This define was left over from a previous revision, and was never used.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This will be replaced with the driver model version
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Stefan Roese <sr@denx.de>
CC: Tom Rini <trini@konsulko.com>
Unfortunately this board has no DM support at all. We are also way past
the deadline for driver model support for various devices on this board.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Stefan Roese <sr@denx.de>
These boards use an MMC driver that does not use this definition
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Stefan Roese <sr@denx.de>
CC: Mario Six <mario.six@gdsys.cc>
CC: Dennis Gilmore <dgilmore@redhat.com>
Call 'run update_uboot' to fetch u-boot-spl.kwb via TFTP and write it
into the correct SPI flash location. The latter's size is defined in
DS414's DTB file, so hard-coding it should be acceptable here.
Take care to not append garbage from RAM to the written image and to
stay within assigned flash boundaries even if an oversized image was
fetched.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Move the relevant bits from ds109.{c,h} into common/ and adjust the code
to fit both DS109 and DS414. Moreover:
* Introduce syno_board_id() which translates CONFIG_MACH_TYPE into the
expected board ID tag value.
* Properly initialize isusbhost, mac and mtu fields from env variables.
* Set the right bootargs/bootcmd to correctly boot legacy kernel out of
the (DS414) box. Getting the ramdisk location right is a bit tedious.
Cc: Walter Schweizer <swwa@users.sourceforge.net>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBr+AgRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebnqQf/dZUk4cpj4q29icFJhAhG3wUkzKdKywWu
wOwHPIaUIetytpjwKTbkv0cUdel5Jhp9mvnJ2O5cRUZlVdgCH+lEQmFiq1O74Jf5
IwYBN74xZuP7+rno3ZxuKhjj2ixbpeg2A5R/o7gaevIgtu4vCK71qrj3y+unjnnt
Rd5BGaVzouMya0lS9cdkrzE1vmuLXs7ZJBvKdppaNda0VScJj+JP3NqooFKRKPU+
OeyblmtfL5lGOXFdY7Wfjg0pzv5L8fJxDaYDxf6iRWWG/X6RO6zV26MWAo28Ga+J
E3fuvl0mBqr1eAg3Cf17j4s9gRZv1tMtS6Mol1scIcBrldalVFA44g==
=x75X
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm
ENOSYS clean-up
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
Currently it is not possible to boot Linux from the SD card
by default.
Make the necessary adjustments to allow it.
Reported-by: Peter Bergin <peter@berginkonsult.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrey Zhizhikin <andrey.z@gmail.com> # imx8mn_ddr4_evk
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Drop a irrelevent comment now the related configs have moved
to the various config files.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mimicing for example the rk3399, set the SYS_BOOTM_LEN to 64MB so
that regular kernel images can get loaded without problems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SYS_LOAD_ADDR currently is at 0x00280000 which is only 512KB
behind the area where we load u-boot to, which depending on u-boot size
may overlap at some point.
So for safety just pick the same value rk3399 has and set
CONFIG_SYS_LOAD_ADDR to 0x00800800 on rk3368 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
At present the eMMC device does not have an alias so it appears after
the SD card which is device 1. There is no device 0 which is odd.
Make the eMMC device be the first one. Update the boot script to use the
new device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
LS1028A-QDS has CONFIG_SPI_FLASH_SST and CONFIG_SPI_FLASH_EON defines
present in header. Move these entries from header to defconfigs.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is now safe to remove Flexspi configs NXP_FSPI_FLASH_SIZE and
NXP_FSPI_FLASH_NUM options from headers as they are no longer used by
driver anymore.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
More than one pumpkin board has been made with different MediaTek SoCs.
Rename the pumpkin board to follow the naming convention of all
other MediaTek boards and also to not be confusing when other pumpkin
boards will be added in follow-up commits.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).
This patch adds the required board support to boot Si-Linux EK874 board
based on R8A774C0 SoC.
DTS files apart from r8a774c0-ek874-u-boot.dts and r8a774c0-u-boot.dtsi
have been imported from Linux kernel 5.11 commit f40ddce88593
("Linux 5.11").
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
The HiHope RZ/G2M board from HopeRun consists of main board
(HopeRun HiHope RZ/G2M main board) and sub board(HopeRun
HiHope RZ/G2M sub board). The HiHope RZ/G2M sub board sits
below the HiHope RZ/G2M main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2M board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
-----BEGIN PGP SIGNATURE-----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=nIJc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210312' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Add WATCHDOG_RESET() in MTD framework and STM32 QSPI driver
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
Current BSS allocation of SPL is as below:
$ size spl/u-boot-spl
text data bss dec hex filename
132369 7852 1496 141717 22995 spl/u-boot-spl
But 20KB is allocated currently for BSS. Reduce it to 3KB and save some
space for stack.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In a previous attempt to unify config options and remove items
from the whitelist file, SPL items were moved into a section
enabled with CONFIG_SPL_BUILD. Unfortunately, SPL_PAD_TO
is referenced at the head Makefile and uses this define
to create padding of the output file. When it was moved
to CONFIG_SPL_BUILD, it caused boot errors with devices
that are not booting from NOR. Fix the boot issues by moving
SPL_PAD_TO out so it's always.
Fixes: 7bb33e4684 ("ARM: da850-evm: Unify config options with Kconfig")
Signed-off-by: Adam Ford <aford173@gmail.com>
The STM32MP15 boards have no reason to configure bootdelay in stm32mp1.h
as it is already done with CONFIG_BOOTDELAY (default = 2) and in
include/env_default.h.
This patch allows configuration for customers which reuse stm32mp1.h
and reduce the size of the default environment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add target to Makefile to generate "u-boot-spl-dtb.hex" for Intel
SOCFPGA SOC64 devices (Stratix 10 and Agilex). "u-boot-spl-dtb.hex"
is hex formatted spl with and offset of CONFIG_SPL_TEXT_BASE. It
combines the spl image and dtb. "u-boot-spl-dtb.hex" is needed to
generate the final configuration bitstream for Intel SOCFPGA SOC64
devices.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
CONFIG_BOOTCOMMAND have been moved to Kconfig.boot. This patch
move the CONFIG_BOOTCOMMAND macro from socfpga_soc64_common.h to
*_defconfig file for both Stratix 10 and Agilex.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Now that we have switched to CONFIG_OF_CONTROL, and we can use the
env variable 'fdtcontroladdr' directly instead of creating one that
is duplicated.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The QEMU ppce500 target integrates a Freescale I2C controller and
has a Pericom pt7c4338 RTC connected to it. Enable corresponding
DM drivers so that 'date' command is actually useful.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present the board supports non-DM version PCI and E1000 drivers.
Switch over to use DM ETH and PCI by:
- Rewrite the PCI address map functions using DM APIs
- Enable CONFIG_MISC_INIT_R to do the PCI initialization and
address map
- Drop unnecessary ad-hoc config macros
- Remove board_eth_init() in the board codes
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The QEMU ppce500 target integrates 2 NS16550 serial ports. Switch
over to use the DM version of the driver by:
- drop unnecessary ad-hoc config macros
- add get_serial_clock() in the board codes
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_SYS_PCI_MAP_END currently points to 0xe8000000, which means
the upper end of the virtual address mapped to PCI bus address ends
at 0xe8000000. But this is wrong as the CCSBAR was already mapped
at 0xe0000000 with a 1 MiB size.
Fixes: fa08d39517 ("PPC 85xx: Add qemu-ppce500 machine")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds support for more PMBus compatible devices to the NXP
drivers for its QorIQ family devices. At runtime, the voltage regulator is
queried over I2C, and the required voltage multiplier determined. This
change supports the DIRECT and LINEAR PMBus voltage reporting modes.
Previously, the driver only supported a few specific devices such as the
IR36021 and LTC3882, so this change allows the QorIQ series to be used
with a much larger variety of core voltage regulator devices.
checkpatch warning "Use if (IS_DEFINED (...))" was ignored to maintain
consistency with the existing code.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_VIDEO migration deadline is already expired, but around
80 Allwinner boards are still using video in a legacy way:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Convert the legacy video driver over to the DM_VIDEO framework. This is
a minimal conversion: it doesn't use the DT for finding its resources,
nor does it use DM clocks or DM devices for the outputs (LCD, HDMI, CVBS).
Tested in Bananapi M1+ Plus 1920x1200 HDMI out. (Jagan)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: rebase and smaller fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now when usbtty serial console is fixed in U-Boot enable CONFIG_USB_TTY for
Nokia RX-51 board by default.
Fix also USB product id as U-Boot ignores CONFIG_USBD_PRODUCTID macro and
include U-Boot string into USB product name to indicate usage of U-Boot.
CONFIG_CONSOLE_MUX is already used and U-Boot console is available for
all in/out devices. Therefore there is no need to have separate commands
'run sercon', 'run usbcon' and 'run vgacon', so remove them.
As space for U-Boot is limited to 256kB, enable CONFIG_OPTIMIZE_INLINING
and disable some other unused options so CONFIG_USB_TTY can be enabled.
Nokia RX-51 does not have easily accessible UART serial console so the only
option for easy debugging is to use device's keyboard+screen or this usbtty
serial console over USB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
There is a second lpddr configuration with 2GB of RAM, but this requires
different RAM timings, so in addition to adding the timing file, a
separate defconfig is necessary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Make the conversion to driver model as it is mandatory.
Tested booting the Linux kernel from the SD card.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Remove the SATA support for now as the i.MX53 support has not
been added yet.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The RGMII link delays can be set on either MAC or PHY side. Set the
rgmii-id PHY mode for FEC and remove FEC_ENET_ENABLE_.XC_DELAY
setting, so that these definitions aren't used anymore throughout
the U-Boot.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Both NXP SoCs i.MX8 and i.MX8X have ENET gigabit MAC.
Define FEC_QUIRK_ENET_MAC for the imx8 platform and remove this
definition from configs of boards, based on MX8/MX8X.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Some root filesystem configurations do not have separate /boot partition,
but rather place kernel, DT, scripts into /boot directory. Search the /boot
directory for these boot components in case they are not found in /, which
is the old behavior.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Replace filesystem specific fatload command with a filesystem agnostic
load command, so the board can boot from e.g. ext4 too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There is now CONFIG_SPL_DM_SPI{,_FLASH}, however keeping
CONFIG_DM_SPI{,_FLASH} enabled in SPL seems to grow the SPL
by a couple of bytes:
text data bss dec hex filename
- 34069 1568 96 35733 8b95 spl/u-boot-spl
+ 34075 1568 96 35739 8b9b spl/u-boot-spl
In either case, the binary is bootable, so remove the part
in board config.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
This reverts commit 03a673cf49 ("dh_imx6: Switch to full DM-aware").
According to discussion [1], the patch is known to break the dh_imx6
board, however it made it upstream just before 2021.01-rc4, likely by
mistake. Revert this patch to put the board back into working order.
Also note that this board has no DM SPL support due to OCRAM size
limitations, but that is fine, as SPL DM support is optional.
[1] https://lists.denx.de/pipermail/u-boot/2020-June/417986.html
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Add support for booting from USB pen drive, since USB host port is
available on the STM32MP1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is the last ARCH_MPC8569 board, remove that support
as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Convert the hikey to use DM_USB and DM_ETH.
Conversion based on rpi as it has a similar DWC config.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Drop CONFIG_DM_I2C undefs from board header files, and make them
disabled on these boards in defconfigs instead.
Disabling on Kconfig symbol was done automatically with this script:
cd configs
files=(*ls1046a*)
files2=(*T104*RDB*)
files3=(ls1021atwr_*)
files4=("imx8mp_evk_defconfig phycore-imx8mp_defconfig")
combine=("${files[@]}" "${files2[@]}" "${files3[@]}" "${files4[@]}")
cd ..
for item in ${combine[*]}
do
echo "Adjusting $item"
echo "# CONFIG_SPL_DM_I2C is not set" >> configs/$item
make $item && make savedefconfig && cp defconfig configs/$item
done
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
OF_STDOUT_PATH was meant to hold the devicetree path to the serial
console, to be put into the linux,stdout-path property of the chosen node.
The only user of that was sunxi, and it was actually wrong for years
there: the paths hardcoded in sunxi_common.h were not matching the DTs,
evident by the leading 0's in nodenames, which have been removed years
ago.
On top of that, "linux,stdout-path" is now deprecated for a while (Linux
commit 2a9d832cc9aae from November 2014), and also all modern DTs
(including those included in U-Boot) carry a "stdout-path" property
already.
So remove the stanza from sunxi_common.h, and, since this was the last
user, also remove the associated bits from the rest of U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As variables were moved to Kconfig, some of the surrounding ifdefs were
left around, even though they were empty. Clean them up.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
As this is the last SH4A board, remove that support as well.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Patch-cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Patch-cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Chris Packham <judge.packham@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lauri Hintsala <lauri.hintsala@silabs.com<mailto:lauri.hintsala@silabs.com>>
Signed-off-by: Tom Rini <trini@konsulko.com<mailto:trini@konsulko.com>>
Enable the fastboot oem command format and set the variable
"partitions" with default eMMC partitions list.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Jean-Philippe ROMAIN <jean-philippe.romain@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Espressobin: Set default env values at runtime (Pali)
- Espressobin: Set the maximum slave SPI speed to 40MHz (Pali)
- theadorable: PCIe test code enhancement and early deemphasis
enabling (Stefan)
- pci_mvebu: Disable config access to PCI host bridge ports (Stefan)
- mv_sdhci: parse device-tree entry (Baruch)
Cleanup, move the declarations to keymile/common.h instead declaring them
per-board config.h
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable SATA support. Although not supported by the usual SATA pins on
the SMARC baseboard connector, SATA mode is supported on a PCIe lane.
This way one can use a mSATA card in a Mini PCI slot.
We need to invert the received data because in this mode the polarity of
the SerDes lane is swapped. Provide a fixup in board_early_init_f() for
the SPL. board_early_init_f() is then not common between SPL and u-boot
proper anymore, thus common.c is removed, as it just contained said
function.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add COMMON_ENV(kernelheader_addr_r, fdtheader_addr_r,
kernel_addr_r, fdt_addr_r, load_addr)
to fix a bug that failed to boot to ubuntu
Failed log as follows,
## Executing script at 80000000
load - load binary file from a filesystemUsage:
load <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- Load binary file filename from partition part on device
type interface instance dev to address addr in memory.
bytes gives the size to load in bytes.
If bytes is 0 or omitted, the file is read until the end.
pos gives the file byte position to start reading from.
If pos is 0 or omitted, the file is read from the start.
...
Bad Linux ARM64 Image magic!
SCRIPT FAILED: continuing...
Signed-off-by: Biwen Li <biwen.li@nxp.com>
[Updated description]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
On Espressobin board are MAC addresses stored in U-Boot env area. Therefore
they are not present in default_environment[] array constructed at compile
time.
This change puts permanent MAC addresses into default_environment[] array
at board runtime. Espressobin board has enabled DEFAULT_ENV_IS_RW option
and therefore can modify this array.
This change ensure that 'env default -a' does not delete permanent MAC
addresses from Espressobin env storage area.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
On Espressobin board value for $fdtfile cannot be determined at compile
time and is calculated at board runtime code. This change uses a new option
DEFAULT_ENV_IS_RW to allow modifying default_environment[] array at runtime
and set into it correct value.
This change also ensure that 'env default -a' set correct value to $fdtfile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.
Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).
Signed-off-by: David Lechner <david@lechnology.com>
With the recent addition of ACPI generation, the image size has got beyond
its current limit.
Samus does not actually use this, nor x86 emulation for PCI ROMs, so
disable both features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Re-send because of line-wraps.
This patch fixes the behaviour of the menuconfig's BOOTCOMMAND
setting. Which is just ignored without that patch on
vexpress_aemv8a platform.
Signed-off-by: Stanislav.Pinchuk@kaspersky.com
- Espressobin: Disable slot when emmc is not present (Pali)
- DS414; config header cleanup (Phil)
- PCI: auto-config enhancement (Phil)
- pci_mvebu: Also map IO region (Phil)
- serial: a3720: Implement pending method for output direction (Pali)
- turris_mox: Enable a few commands (Marek)
- helios4 & ClearFog changes (Dennis)
- Plus some minor misc changes
Add CAxxxx Ethernet support for the Cortina Access
Presidio Engineering Board
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
A few minor changes:
* Get rid of leftover comments, other commits removed the defines they
referred to.
* CONFIG_SYS_NETA_INTERFACE_TYPE is not used anymore since commit
e3b9c98a23 ("net: mvneta: Convert to driver model").
* Drop CONFIG_USB_MAX_CONTROLLER_COUNT: it is per-HCI type, so XHCI and
EHCI could still both work be used.
* Unconditionally define CONFIG_EHCI_IS_TDI: it has no effect on XHCI so
that conditional doesn't make any sense.
* Define a larger PHY_ANEG_TIMEOUT: In my test bed, the NIC is directly
connected to some RTL8111 and the default 8s timeout was often too
short.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
This patch adds support for MediaTek MT7620 SoC.
All files are dedicated for u-boot.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Supported boot device types in iMX8MQ: MMC, DHCP.
CONFIG_DISTRO_DEFAULTS is added for enabling the DISTRO_DEFAULTS option.
CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mq_evk.h is
deleted because "run distro_bootcmd" is required to be the default boot
mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution.
kernel_addr_r is the location in RAM where the kernel will be loaded to.
Delete unnecessary environment variables because "run distro_bootcmd" is
set to be the default boot mode.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
This patch converts the dart6ul ethernet support to DM_ETH and cleans
up the legacy ethernet code. The clean up, more specifically:
* moves the fec2 node and pin definition to the carrier board DTS
since the phy associated with it is on the carrier board and not on
the SoM;
* add the reset pin associated to each phy;
* separate the ethernet, mdio and reset pins of each fec so that they
are easier to reference;
* add clock properties to the phy nodes since they are connected to the
50Mhz ENET[12]_TX_CLK clock of the SoC;
* remove CONFIG_BOARD_EARLY_INIT_F since the function is now empty.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Supported boot device types in iMX8MP: MMC.
CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is
for command fstype.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution. kernel_addr_r is the location in RAM where
the kernel will be loaded to. Delete unnecessary environment variables
because "run distro_bootcmd" is set to be the default boot mode.
On the iMX8MP platform I used, "mmc1" represents SD card and "mmc2"
represents eMMC.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Supported boot device types in iMX8MM: MMC, DHCP.
CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is
for command fstype.
CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mm_evk.h is
deleted because "run distro_bootcmd" is required to be the default boot
mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution.
kernel_addr_r is the location in RAM where the kernel will be loaded to.
Delete unnecessary environment variables.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
The DWMAC4 IP has the possibility to skip up to 7 AXI bus width size words
after the descriptor. Use this to pad the descriptors to cacheline size and
remove the need for noncached memory altogether. Moreover, this lets Tegra
use the generic cache flush / invalidate operations.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add low level platform initialization for the AST2600 SoC.
The 2-stage booting with U-Boot SPL are leveraged to support
different booting mode.
However, currently the patch supports only the booting from
memory-mapped SPI flash.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Set environment for Nand flash (U-boot 2020.04):
- add nand flash in the device tree
- add new default configuration file for G3 using parallel Nand
- set nand parameters in presidio_asic.h
Signed-off-by: Kate Liu <kate.liu@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds Microchip MPFS Icicle Kit support. For now, only
NS16550 Serial, Microchip clock, Cadence eMMC and MACB drivers are
enabled. The Microchip MPFS Icicle defconfig by default builds
U-Boot for S-Mode because U-Boot on Microchip PolarFire SoC will run
in S-Mode as payload of HSS + OpenSBI.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Added support for timer_early_get_count() and timer_early_get_rate()
This is mostly useful in tracing.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This enables configs necessary for using SPI. The environment is saved to
the very end of SPI flash. This is unlikely to be overwritten unless the
entire flash is reprogrammed.
This also supplies a default bootcommand. It loads an image and device tree
from the first partition of the MMC. This is a minimal/least effort
bootcmd, so suggestions (especially in the form of patches) are welcome. I
didn't set up distro boot because I think it is unlikely that any
general-purpose linux distros will ever be ported to this board.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Chrstopher Obbard <obbardc@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add CONFIG_SPL_PAD_TO for Gen5 and Arria 10. CONFIG_SPL_PAD_TO is set to
size of OCRAM.
This is preparation for image padding change in socfpgaimage.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Since SSBL is running in DRAM, it shall setup the stack in DRAM
instead of OCRAM which is occupied by SPL and handoff data.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Instead of loading u-boot proper image (u-boot.img), SPL
now loads FIT image (u-boot.itb) which includes u-boot
proper, ATF and u-boot proper's DTB.
For OS, u-boot now loads FIT images (kernel.itb) which
includes Linux Image and Linux's DTB.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
- DM support for OMAP PWM backlight
- USB host mode support for AM654
- Minor SPI fixes
- Add support k2g ice board with 1GHz silicon
- Fix GTC programming for K3 devices
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/8S/0cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKFkB/9NBJq/+sgHZXRaMlAu
ULNwOPoNsQxHQGwF88B1lC+H8LJjM+2gJ8MfJdWvHNlcSdtJjbWk0aQL+5LKSlyz
G7l3BZ+AIYMOeTXay5mNUKnekXIr7c8tLoX8FH/Ih+bHFPt57qL0bbfznV66UCOp
/o/yM8daPa9Kx1vPEpT2dC9bYXLXeQv6R+RMxwoc4Bk+R3OK7zoZ3Wdx0q9HvBwj
iWHM49X2fBqqi5RS+ZI37AUzi8iysD3fOq0kWTJcCNaci8i8RZdzSyoaDuXhA63I
EZJ7v9fUkW/bwTONVE9n2BX4xF9X/6R7P46l9dQISXAxsOBwsNRQPt8Ro7mCoc4K
392o
=LIK7
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2021.04 cycle
This feature set includes the new board SAMA7G5 EK, the new evaluation
kit for Microchip AT91 SAMA7G5 SoC . The current board support includes
two configurations for booting from eMMC (SDMMC0), SD-Card (SDMMC1), and
support for two Ethernet interfaces.
Those two commands now doing same thing, reading from ext2/3/4 filesystem.
So remove useless duplicated call.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
As more and more LINUX drivers are modified to use asynchronous probing
instead of synchronous probing, relying on device names being equal in
U-Boot and LINUX is not possible anymore. This is also true for block
device names like mmc0, mmc1 ect.
With LINUX kernel commit a1a4891 the probing type for the sdhci-omap
driver has been set to asynchronous mode too (probe_type is now
PROBE_PREFER_ASYNCHRONOUS).
In the case of the PDU001 board this results in the devices mmc0 and
mmc1 being swapped between U-Boot and LINUX. Device mmc0 in U-Boot
becomes mmc1 in LINUX an vice versa. Hence using device name identifiers
with LINUX kernel parameter root does not work anymore.
This patch changes the LINUX kernel boot parameter root to use the
pseudo (since we use MBR not GPT) partition UUID to locate the partition
hosting the root file system.
Signed-off-by: Felix Brack <fb@ltec.ch>
In include/dfu.h, if CONFIG_SYS_DFU_MAX_FILE_SIZE is not defined then it is
defined as CONFIG_SYS_DFU_DATA_BUF_SIZE. This is 128 KiB for a53 core and
20 KiB for r5 core. If a larger file is transferred using dfu then it
fails.
CONFIG_SYS_DFU_DATA_BUF_SIZE can not be increased as there is not enough
heap memory to be allocated for the buffer in case of R5 spl.
Fix this by defining CONFIG_SYS_DFU_MAX_FILE_SIZE as the default
CONFIG_SYS_DFU_DATA_BUF_SIZE value.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
So far we did not support the BootROM based FEL USB debug mode on the
64-bit builds for Allwinner SoCs: The BootROM is using AArch32, but the
SPL runs in AArch64.
Returning back to AArch32 was not working as expected, since the RMR
reset into 32-bit mode always starts execution in the BootROM, but not
in the FEL routine.
After some debug and research and with help via IRC, the CPU hotplug
mechanism emerged as a solution: If a certain R_CPUCFG register contains
some magic, the BootROM will immediately branch to an address stored in
some other register. This works well for our purposes.
Enable the FEL feature by providing early AArch32 code to first save the
FEL state, *before* initially entering AArch64.
If we eventually determine that we should return to FEL, we reset back
into AArch32, and use the CPU hotplug mechanism to run some small
AArch32 code snippet that restores the initially saved FEL state.
That allows the normal AArch64 SPL build to be loaded via the sunxi-fel
tool, with it returning into FEL mode, so that other payloads can be
transferred via FEL as well.
Tested on A64, H5 and H6.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Priit Laes <plaes@plaes.org> (on Olimex A64-Olinuxino)
The usage of the preboot feature is now controlled via a separate Kconfig
option - namely CONFIG_USE_PREBOOT.
It must be enabled for preboot code executing commands now defined in
CONFIG_PREBOOT (also moved to the Kconfig).
After defining both CONFIG_USE_PREBOOT and CONFIG_PREBOOT in
imx28_xea_defconfig the define of CONFIG_PREBOOT shall be removed from
xea.h as it is redundant.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Clean-up boot command to use the predefined device and part for FAT
environment.
According to this device and partition, select the proper boot media.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Heap base address is computed based on SYS_INIT_SP_ADDR by
subtracting the SYS_MALLOC_F_LEN value in
board_init_f_init_reserve().
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
Add parallel nor device to distroboot for microblaze.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Instead of hardcoding index magic numbers in the board code,
also rely on board_fit_config_name_match choosing the right
config for the fitImage containing the kernel.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since linux commit 2e6cde96873253fd9eb0f20afd8ffd18278cff75 ("arm64:
dts: ls1028a: make the eMMC and SD card controllers use fixed indices")
mmc0 is the eMMC and mmc1 is the SD card. Also swap it in u-boot to
avoid any confusion by the user and to be aligned with linux.
Signed-off-by: Michael Walle <michael@walle.cc>
Enable DM_SPI/DM_SPI_FLASH with a related config option.
Build fine, but not tested.
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI/DM_SPI_FLASH with a related config option.
Build fine, but not tested.
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Make use of the new bootargs substitution mechanism and zboot command
syntax.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
=cgbE
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Set `bootcause' from b850v3 power management watchdog status.
Boot cause "REVERT" is no longer used, remove it.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix typo in NFS command configuration check.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
Activate ARCH_SUPPORT_PSCI as other TEGRA124 target and remove
CONFIG_ARMV7_PSCI and CONFIG_ARMV7_PSCI_NR_CPUS in configs file as they
are migrated in Kconfig.
Select CONFIG_ARMV7_PSCI_0_1 (the first PSCI version),
because CONFIG_ARMV7_PSCI_0_2 and CONFIG_ARMV7_PSCI_1_0
are not activated in this product.
Hi,
This patch depend on the previous serie [1].
I don't test this patch on real hardware but
after this patch the size of the binary don't change.
In .config we have:
CONFIG_ARCH_SUPPORT_PSCI=y
CONFIG_ARMV7_PSCI=y
# CONFIG_ARMV7_PSCI_1_0 is not set
# CONFIG_ARMV7_PSCI_0_2 is not set
CONFIG_ARMV7_PSCI_0_1=y
CONFIG_ARMV7_PSCI_NR_CPUS=4
In u-boot.cfg, this patch only add the 2 lines
#define CONFIG_ARCH_SUPPORT_PSCI 1
#define CONFIG_ARMV7_PSCI_0_1 1
[1] "Convert CONFIG_ARMV7_PSCI_1_0 and CONFIG_ARMV7_PSCI_0_2 to Kconfig"
http://patchwork.ozlabs.org/project/uboot/list/?series=184029
Regards
Patrick
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Upstream linux DT naming doesn't align with the U-Boot DT, which may
not always be the case so this allows using BOOTENV_EFI_SET_FDTFILE_FALLBACK
where it might be appropriate for some boards.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For booting via UEFI we need to define the fdtfile option so
bootefi has the option to load a fdtfile from disk. For arm64
the kernel dtb is located in a vendor directory so we define
that as nvidia for that architecture.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was used for a board which is not supproted anymore and can
therefore be dropped.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This option is obsolete since 2009 and can be removed globally.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Address most of the checkpatch issues we found in km_arm and common km
code.
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no reason to define default option for this macro which is
already done in common/cli_hush.c.
87 #ifndef CONFIG_SYS_PROMPT_HUSH_PS2
88 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
89 #endif
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Remove fixed configuration and detect flash based on DT.
Also increase amount of flash sectors to 2048 because on kc705 flash has
1027 sectors.
Bank # 1: CFI conformant flash (16 x 16) Size: 128 MB in 1027 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8962
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
