Add a function to set the video parameters to the msg handler and remove
it from the video driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add a function to get the video size to the msg handler and remove it from
the video driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
The bcm283x chips provide a way for the ARM core to communicate with the
graphics processor, which is in charge of many things. This is handled by
way of a message prototcol.
At present the code for sending message (and receiving a reply) is spread
around U-Boot, primarily in the board file. This means that sending a
message from a driver requires duplicating the code.
Create a new message implementation with a function to support powering on
a subsystem as a starting point.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is needed to probe devices under that bus such as the SATA PHY.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9263ek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9rlek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9g20ek and at91sam9260ek
boards are copied from the Linux v4.10, do the changes below.
- Fix the build error for the usb0 node.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Add the clk pinctrl of the mmc0 node.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9m10g45ek boards are copied
from the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9n12ek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the pinctrl-names of mmc0 node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9x5ek board are copied from
the Linux v4.10, do the changes below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Move existing configuration from header file to defconfig or dts as
appropriate.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Align PHY selectors register with Armada-CP-110 functional SPEC
update all relevant device trees with this change.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so rename
TO_USB_HOST to TO_USB3_HOST to distinguish TO_USB2_HOST in later on patches.
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use correct naming as done in the latest Marvell U-Boot version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Fix spelling error of SERDES_VERSION
- Remove superfluous definition of this macro
- Remove unnecessary include of i2c.h
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add NAND to CP master device tree. Add armada-7040-db-nand
device tree for the board configured with NAND boot device.
Add comment about boot device ID to armada-7040-db DTS.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Implement mvebu_get_nand_clock call for A8K family.
This function is used by PXA3XX NAND driver.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add PCIe initialization at early init stage.
This operation has a side effect of detecting all PCIe
plug-in cards, so the operator is not obligated to issue
"pci enum" command though CLI for this purpose.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Sync the default configuration of Armada-8040-DB with
Marvell u-boot-2015 standard configuration "A" for the same board.
The standard configuration "A" enables 2 PCIe slots on CP0
and 3 PCIe slots on CP1.
This is the main configuration used for u-boot and Linux tests.
This patch also re-arranges the DTS file entries by grouping
all nodes related to CP0 and CP1.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable by default DM_I2C for all Texas Instruments Keystone 2 based
evms.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Enable I2C0 and I2C1 which is needed to enable usage of DM I2C.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add aliases for I2C nodes required for the DM framework to probe the
davinci-i2c driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add I2C nodes to the 66AK2Gx dtsi.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
One some keystone2 platforms like K2G ICE, there is an option
to switch between 24MHz or 25MHz as sysclk. But the existing
driver assumes it is always 24MHz. Add support for getting
all reference clocks dynamically by reading boot pins.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
K2G supports various sysclk frequencies which can be
determined using sysboot pins. PLLs should be configured
based on this sysclock frequency. Add PLL configurations
for all supported sysclk frequencies.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
ARM errata 852421 and 852423 applies to r1p0, r1p1 and r1p2
revisions of Cortex-A17 processors. These workarounds
exist in Linux kernel and I thought it would be better
to add them in to U-Boot.
Signed-off-by: Nisal Menuka <nisalmenuka23@gmail.com>
Remove unnecessary apb and ahb nodes and just override necessary
nodes/values.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refactor SCU header to use consistent Mask & Shift values.
Now, consistently, to read value from SCU register, mask needs
to be applied before shift.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for clocks needed by MACs to ast2500 clock driver.
The clocks are D2-PLL, which is used by both MACs and PCLK_MAC1 and
PCLK_MAC2 for MAC1 and MAC2 respectively.
The rate of D2-PLL is hardcoded to 250MHz -- the value used in Aspeed
SDK. It is not entirely clear from the datasheet how this clock is used
by MACs, so not clear if the rate would ever need to be different. So,
for now, hardcoding it is probably safer.
The rate of PCLK_MAC{1,2} is chosen based on MAC speed selected through
hardware strapping.
So, the network driver would only need to enable these clocks, no need
to configure the rate.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add P-Bus Clock support to ast2500 clock driver.
This is the clock used by I2C devices.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver uses Generic Pinctrl framework and is compatible with
the Linux driver for ast2500: it uses the same device tree
configuration.
Not all pins are supported by the driver at the moment, so it actually
compatible with ast2400. In general, however, there are differences that
in the future would be easier to maintain separately.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change switches all existing users of ast2500 Watchdog to Driver
Model based Watchdog driver.
To perform system reset Sysreset Driver uses first Watchdog device found
via uclass_first_device call. Since the system is going to be reset
anyway it does not make much difference which watchdog is used.
Instead of using Watchdog to reset itself, SDRAM driver now uses Reset
driver to do that.
These were the only users of the old Watchdog API, so that API is
removed.
This all is done in one change to avoid having to maintain dual API for
watchdog in between.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Reset Driver configuration to ast2500 SoC Device Tree and bindings
for various reset signals
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Reset Driver for ast2500 SoC. This driver uses Watchdog Timer to
perform resets and thus depends on it. The actual Watchdog device used
needs to be configured in Device Tree using "aspeed,wdt" property, which
must be WDT phandle, for example:
rst: reset-controller {
compatible = "aspeed,ast2500-reset";
aspeed,wdt = <&wdt1>;
}
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make functions for locking and unlocking SCU part of SCU API.
Many drivers need to modify settings in SCU and thus need to unlock it
first. This change makes it possible.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver supports ast2500 and ast2400 SoCs.
Only ast2500 supports reset_mask and thus the option of resettting
individual peripherals using WDT.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch is required for correct SPL device tree creation by fdtgrep
as fdtgrep looks for u-boot,dm-pre-reloc property of the node to include
it in the spl device tree.
Not adding it in these subnodes ignores the pin muxing of peripherals
which is almost always in the subnodes.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The IGEP SMARC AM335x is an industrial processor module with
following highlights:
o AM3352 TI processor (Up to AM3359)
o Cortex-A8 ARM CPU
o SMARC form factor module
o Up to 512 MB DDR3 SDRAM / 512 MB FLASH
o WiFi a/b/g/n and Bluetooth v4.0 on-board
o Ethernet 10/100/1000 Mbps and 10/100 Mbps controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Pau Pajuelo <ppajuelo@iseebcn.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
Rename igep0033 to igep003x as IGEP SMARC AM335x module (igep0034)
can use the same source files.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
am33xx does not support OneNAND, but we need this define anyway
to let UBI SPL code compile.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
This board support stm32f7 family device stm32f769-I with 2MB internal Flash &
512KB RAM.
STM32F769 lines offer the performance of the Cortex-M7 core (with double
precision floating point unit) running up to 216 MHz.
To compile for stm32f769 board, use same defconfig as stm32f746-disco,
the only difference is to pass "DEVICE_TREE=stm32f769-disco".
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Actually the sdram memory on stm32f746 discovery board is micron part
MT48LC_4M32_B2B5_6A. This patch does the modification required in the
device tree node & driver for the same.
Also we are passing here all the timing parameters in terms of clock
cycles, so no need to convert time(ns or ms) to cycles.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
All discovery boards have one user button & one user LED. Here we are
just reading the button status & switching ON the user LED.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
With this gpio driver supporting DM, there is no need to enable clocks
for different gpios (for pin muxing) in the board specific code.
Need to increase the allocatable area required before relocation from 0x400 to
0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Also created alias for gpios for stm32f7 discovery board. Based on these
aliases, it would be possible to get gpio devices by sequence.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
This patch also removes the sdram/fmc clock enable from board specific
code.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
At present fdt blob or argument address being passed to kernel is fixed at
compile time using macro CONFIG_SYS_SPL_ARGS_ADDR. FDT blob from
different media like nand, nor flash are copied to the address pointed
by the macro.
The problem is, it makes args/fdt blob compulsory to copy which is not required
in cases like for NOR Flash. This patch removes this limitation.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
The symbol CONFIG_DRA7XX is needed for Kconfig conditions.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
In dram_init_banksize there seems to be a typo concerning
a plausibility check of the fdt.
Testing sc > 2 twice does not make any sense.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
R40 has a similar SATA controller with the ones on A10/A20, but with a
reset line added (like other peripherals on sun6i+), and two extra VDD
pins added (1.2v and 2.5v).
Add clock configuration of R40 SATA.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
For the consistent location of SoC-level Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With 3f66149d9f we no longer have a common call fdt_fixup_ethernet.
This was fine to do on PowerPC as they largely had calls already in
ft_cpu_fixup. On ARM however we largely relied on this call. Rather
than introduce a large number of changes to ft_cpu_fixup /
ft_board_fixup we recognize that this is a common enough call that we
should be doing it in a central location. Do it early enough that we
can do any further updates in ft_cpu_fixup / ft_board_fixup.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Chou <thomas@wytron.com.tw> (maintainer:NIOS)
Cc: York Sun <york.sun@nxp.com> (maintainer:POWERPC MPC85XX)
Cc: Stefan Roese <sr@denx.de> (maintainer:POWERPC PPC4XX)
Cc: Simon Glass <sjg@chromium.org>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 3f66149d9f ("Remove extra fdt_fixup_ethernet() call")
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_DIAG
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_DIAG on some keymile configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_DEKBLOB
Note: This option does not seem to actually be enabled by any board.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply under SECURE_BOOT for mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than using CMD_CRAMFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CRAMFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply FS_CRAMFS for keymile]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_CRAMFS
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CRAMFS for keymile]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_CLK
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CLK on ARCH_ZYNQ]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_BMODE
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_BLOB
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add imply CMD_BLOB under CHAIN_OF_TRUST]
Signed-off-by: Tom Rini <trini@konsulko.com>
A few boards had not been fully re-synced with CONFIG_ARCH_MX5 / CONFIG_MX51 /
CONFIG_MX53 being in Kconfig. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit adds support for HDMI output.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds support for DM I2C on sunxi platform. It can coexist
with old style sunxi I2C driver, because it is still used in SPL and
by some SoCs.
Because sunxi platform doesn't yet support DM clk, reset and pinctrl
driver, workaround is needed to enable clocks and set resets and
pinctrls. This is done by calling i2c_init_board() in board_init().
This means that CONFIG_I2Cx_ENABLE options needs to be correctly set
in order to use needed I2C controller.
Commit is based on the previous patch made by Philipp Tomsich
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On ARM v7M, the processor will return to ARM mode when executing
a blx instruction with bit 0 of the address == 0. Always set it
to 1 to stay in thumb mode.
Tested on STM32f746-disco board
Similar commit:
f99993c108
Author: Matt Porter <mporter@konsulko.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In Linux, CONFIG_ARCH_OMAP2PLUS is used for OMAP2 or later SoCs.
Rename CONFIG_ARCH_OMAP2 to CONFIG_ARCH_OMAP2PLUS to follow this
naming.
Move the OMAP2+ board/SoC choice down to mach-omap2/Kconfig to slim
down the arch/arm/Kconfig level.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Almost all TI defconfigs enable this already, add this as a default
and remove the explicit assignment.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are more and more cases where if we do not use gcc-6.0 or later we
run into problems where our binaries are too large for the targets.
Given the prevalence of gcc-6.0 or later toolchains at this point in
time, we give notice now that starting with v2018.01 we will require
gcc-6 (or later) for ARM.
Signed-off-by: Tom Rini <trini@konsulko.com>
The name of the gpio bank under DM_GPIO appear to be a copy-paste error.
This changes the name of the gpio bank from am33xx_gpios to omap34xx_gpios.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The register names and offset were not correct as per the TRM for OMAP3530
and OMAP3630. Correct the naing and offsets per the documentation
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fixes the following problem:
zynq-uboot> run dfu_ram
Setting bus to 1
g_dnl_register: failed!, error: -19
The cause appears to be that the USB framework is looking for a usbotg aliases,
so add the alias to point to our USB device.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the Terasic DE10-Nano board. The board
is based on the DE0-Nano-Soc board but adds a larger FPGA
and an HDMI output.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
PSCI can be used on both multiple and single core socs. Current
implementation only allows PSCI to work on multiple core socs.
This patch removes this restriction so that PSCI can work on
single core socs as well.
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add Kconfig option to support loading PPA header from eMMC/SD and
NAND Flash.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As we have now V3s support in board code, the V3s DTSI file should also
be added.
Add also some CCU include headers to satisfy the DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Basic U-Boot support is now present for V3s.
Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.
As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Use - instead of @ for OPP tables
- Add input-delay properties to Cadence eMMC nodes
- Restore full license text because code-diff is annoying
- Fix NAND compatible strings
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The SCP (System Control Processor) or what we call STM (Stand-by
MPU) is integrated in LD4, Pro4, sLD8, LD6b, LD11, and LD20.
For these SoCs, show the information if STM is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This configuration is supposed to be used with ARM Trusted Firmware,
so the SYSTEM_RESET is implemented in BL31. Invoke PSCI instead of
U-Boot's own reset code because we need to coordinate with SCP
(System Control Processor) for the system-level power management.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is needed for HDMI, which will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Video driver for older Allwinner SoCs uses cfb console framework which
in turn uses struct ctfb_res_modes to hold timing informations. However,
DM video framework uses different structure - struct display_timing.
It makes more sense to convert lcdc to use new timing structure because
all new drivers should use DM video framework and older drivers might be
rewritten to use new framework too.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
TCON unit has similar layout and functionality also on newer SoCs. This
commit splits out TCON code for easier reuse later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.
This patch add barebone dtsi/dts files for the R40 and Bananapi M2 Ultra,
as well as a defconfig for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40's CPU controls are a combination of sun6i and sun7i.
All controls are in the CPUCFG block, and it seems the R40 does not
have a PRCM block. The core reset, power gating and clamp controls
are grouped like sun6i.
Last, the R40 does not have a secure SRAM block.
This patch adds a PSCI implementation for CPU bring-up and hotplug
for the R40.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 has the CPUCFG block at the same address as the A20.
Fix it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 seems to have a variant of the memory controller found in
the H3 and A64 SoCs. Adapt the code for use on the R40. The changes
are based on released DRAM code and comparing register dumps from
boot0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the BSP released by Banana Pi, the R40 (sun8iw11p1) has
an extra "PLL lock control" register in the CCU, which controls whether
the individual PLL lock status bits in each PLL's control register work
or not.
This patch enables it for all the PLLs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The watchdog found on the R40 SoC is the older variant found on the A20.
Add the proper "#if defines" to make it work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 SoC uses the AXP221s in I2C mode to supply power.
Some regulator's common usages have changed, and also the recommended
voltage for existing usages have changed. Update the defaults to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 is the successor to the A20. It is a hybrid of the A20, A33
and the H3.
The R40's PIO controller is compatible with the A20,
Reuse the A20 UART and I2C muxing code by adding the R40's macro.
The display pipeline is the newer DE 2.0 variant.
Block enabling video on R40 for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At present if the return to bootrom fails (e.g. because you are not using
the Rockchip's bootrom's pointer table in MMC) then the board prints
SPL message and hangs. Print a message first if we can, to help in
understanding what happened when it hangs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Each call of va_start must be matched by a call of va_end.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If the system is running PSCI firmware, the System Reset function
(func ID: 0x80000009) is supposed to be handled by PSCI, that is,
the SoC/board specific reset implementation should be moved to PSCI.
U-Boot should call the PSCI service according to the arm-smccc
manner.
The arm-smccc is supported on ARMv7 or later. Especially, ARMv8
generation SoCs are likely to run ARM Trusted Firmware BL31. In
this case, U-Boot is a non-secure world boot loader, so it should
not be able to reset the system directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:
[Linux] [U-Boot]
arch/arm/kernel/smccc-call.S -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes* -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h -> include/linux/arm-smccc.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Current sysclk fixing would fix all clocks with 'fixed-clock' compatible.
This patch is to fix sysclk by path to avoid any incorrect fixing.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Number of TZASC instances may vary across NXP SoCs.
So put TZASC configuration under instance specific defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1046ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size
as header is appended to u-boot image. So header will also be
copied from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for the
header.
- Reduce the size of CAAM driver for SPL Blobification functions
and descriptors, that are not required at the time of SPL are
disabled. Further error code conversion to strings is disabled
for SPL build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add NAND secure boot target for ls1043ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript
from NAND to DDR. Offsets for Bootscript on NAND and DDR have been
also defined.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Define bootscript and its header addresses for QSPI target
Also add PPA header address in Kconfig
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The header address of PPA defined in Kconfig.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The RK3399-Q7 ("Puma") SoM exposes UART0 as the Qseven UART (i.e. the
serial line available via standardised pins on the edge connector and
available on a RS232 connector).
To support boards (such as the RK3399-Q7) that require UART0 as a
debug console, we match CONFIG_DEBUG_UART_BASE and add the appropriate
iomux setup to the rk3399 SPL code.
As we are already touching this code, we also move the board-specific
UART setup (i.e. iomux setup) into board_debug_uart_init(). This will
be called from the debug UART init when CONFIG_DEBUG_UART_BOARD_INIT
is set.
As the RK3399 needs to use its board_debug_uart_init() function, we
have Kconfig enable it by default for RK3399 builds.
With everything set up to define CONFIG_BAUDRATE via defconfig and
with to have the SPL debug UART either on UART0 or UART2, the configs
for the RK3399 EVB are then update (the change for the RK3399-Q7 is
left for later to not cause issues on applying the change).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
For using mipi display, we need to enable lcd3v3
which supplied by rk808,so enable rk808 first.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
To enable mipi display, we need to enable pmic
rk808 first for lcd3v3 power,which use i2c0 to
communicate with soc. So enable i2c0.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
when enable PMIC rk808,the system will halt at very
early stage,log is shown as bellow.
INFO: plat_rockchip_pmu_init(1211): pd status 3e
INFO: BL31: Initializing runtime services
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
time 44561b, 0 (<<----Just stop here)
It's caused by the absence of "{ }" in syscon_rk3399.c
,which will lead to memory overflow like below.According
to Sysmap file ,we can find the function buck_get_value
of rk808 is just follow the compatible struct,the pointer
"of_match" point to "buck_get_value",but it is not a
struct and don't have member of compatible, In this case,
system crash. So,on the face, it looks like that rk808 is
guilty.but he is really innocent.
while (of_match->compatible) { <<----------
if (!strcmp(of_match->compatible, compat)) {
*of_idp = of_match;
return 0;
}
of_match++;
}
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3399.
It provides the following feature set:
* up to 4GB DDR3
* on-module SPI-NOR flash
* on-module eMMC (with 8-bit interace)
* SD card (on a baseboad) via edge connector
* Gigabit Ethernet w/ on-module Micrel KSZ9031 GbE PHY
* HDMI/eDP/MIPI displays
* 2x MIPI-CSI
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub)
* on-module STM32 Cortex-M0 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
- USB<->CAN bridge controller
Note that we use a multi-payload FIT image for booting and have
Cortex-M0 payload in a separate subimage: we thus rely on the FIT
image loader to put it into the SRAM region that ATF expects it in.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixed build warning on puma-rk3399:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3399-Q7 (Puma) DTS should (of course) be dual-licensed.
This updates the licensing info in the rk3399-puma.dts.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Most Rockchip socs have the ability to either map the bootrom or a sram
area to the starting address of the cpu by flipping a bit in the GRF.
Newer socs leave this untouched and mapped to the bootrom but the legacy
loaders on rk3188 and before enabled the remap functionality and the
current smp implementation in the Linux kernel also requires it to be
enabled, to bring up secondary cpus.
So to keep smp working in the kernel, mimic the behaviour of the legacy
bootloaders and enable the remap functionality.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Somehow 43b5c78d8d ("rockchip: cosmetic: Sort RK3288 boards") moved
the rock board in between some rk3288 board, probably as a result of
rebasing.
So move it back to its original position above all rk3288 boards.
Fixes: 43b5c78d8d ("rockchip: cosmetic: Sort RK3288 boards")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399 hangs during DMA of the Designware MMC controller, when
performing DMA-based transactions in SPL due to the DDR security settings
left behind by the BootROM (i.e. accesses to the first MB of DRAM are
restricted... however, the DMA is likely to target this first MB, as it
transfers from/to the stack).
System security is not affected, as the final security configuration is
performed by the ATF, which is executed after the SPL stage.
With this fix in place, we can now drop 'fifo-mode' in the DTS for the
RK3399-Q7 (Puma).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
When CONFIG_DM_SCSI is defined, the SATA initialization will be implemented
in the scsi-uclass driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
All the clocks which has to be enabled has to be done in
enable_basic_clocks(), so moving enable sata clock to common
clocks enable function.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Convert Altera DDR SDRAM driver to use Kconfig method.
Enable ALTERA_SDRAM by default if it is on Gen5 target.
Arria 10 will have different driver.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Disable the OC test on MCVEVK as the old PHY version does not provide
this information. This fixes the USB OTG operation.
Signed-off-by: Marek Vasut <marex@denx.de>
Commit ce62e57fc5 ("ARM: boot0 hook: remove macro, include whole
header file") miss out cleaning macro in this header file, and this
has broken implementation of a boot header capability in socfpga
SPL. Remove the macro in this file, and recovering it back
to proper functioning.
Fixes: ce62e57fc5 ("ARM: boot0 hook: remove macro, include whole
header file")
Signed-off-by: Chee, Tien Fong <tien.fong.chee@intel.com>
With the port C enabled, we can read the GPI input state of:
* the DIP switches (USER_DIPSW_HPS[3:0]/HPS_GPI[7:4])
* the push buttons (USER_PB_HPS[3:0]/HPS_GPI[11:8])
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Signed-off by: Sid-Ali Teir <git.syedelec@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Marek Vasut <marex@denx.de>
The Vybrid SoC family has the same display controller unit (DCU)
like the LS1021A SoC. This patch adds platform data, pinmux defines
and clock control to enable the driver for Toradex Colibri Vybrid
module.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
This driver implements MMC support on Meson GX (S905) based systems.
It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
As a prerequisite for adding a Meson GX MMC driver update the
Meson GXBB / Odroid-C2 device tree in Uboot with the latest
version from Linux.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
The MMC SPL locates the BSS section to a different memory region
from text, then use "_image_binary_end" variable to point to the
correct device tree location.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Because the MMC SPL puts the bbs section in the ddr memory, move
calling mem_init() before calling spl_init().
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
When OF_CONTROL is enabled, MMC boot device should not be detected
automatically, it should be MMC1 fixedly only the status "enabled"
is available.
Add NAND Flash boot device as well.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree file for sama5d4ek board.
The dts file is copied from Linux-4.4, do the following changes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree files for sama5d4 Xplained board.
The dts files are copied from Linux-4.4, do the following changes.
- add reg property for pinctrl node.
- move the gpio nodes(pioA, pioB, pioC ...) from the pinctrl child's
nodes to its slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree file for sama5d3 Xplained board.
The dts files are copied from the Linux-4.9, do changes as below.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree files for sama5d3xek board.
The dts files are copied from Linux-4.9, do the changes as below.
- add reg property for the pinctrl node.
- move the gpio nodes (pioA, pioB, pioC ...) as the pinctrl's
slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
- add spi0 node aliases.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
AT91 PIO controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.
Each SoC will have to describe the its limitation and pin
configuration via device tree. This will allow to do not need
to touch the C code when adding new SoC if the IP version is
supported.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The intention of the removal is the preparation to introduce the
new AT91 PIO pinctrl driver.
Use the union to make the PIO3 and PIO2's registers be together
and make their offset aligned.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the CONFIG_ATMEL_LEGACY is undefined, according to the following
defines, at91_set_gpio_value() references to at91_set_pio_value(x, y)
with two parameters.
#define at91_set_gpio_value(x, y) at91_set_pio_value(x, y)
#define at91_get_gpio_value(x) at91_get_pio_value(x)
But there isn't the implementation of at91_set_pio_value(x, y) with
two parameters in U-Boot. This is an error.
Same as at91_get_gpio_value(x) define.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.
Signed-off-by: Simon Glass <sjg@chromium.org>
aes.h is a too generic name if this file can
be exported and used by a program.
Rename it to avoid any conflicts with
other files (for example, from openSSL).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash. The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM. Items in the dtsi file
are specific to the SOM itself. Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
The num/denom is a float value, but in the calculation it is convert
to integer 0, and wrong result.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Adds an additional image type needed for supporting secure keystone
devices. The build generates u-boot_HS_MLO which can be used to boot
from all media on secure keystone devices.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
As K2 can directly boot U-Boot, add u-boot_HS_MLO as the secure image
name for secure K2 devices, for all boot modes other than SPI flash.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Like the OMAP54xx, AM43xx, & AM33xx family SoCs, the keystone family
of SoCs also have high security enabled models. Allow K2E devices to
be built with HS Device Type Support.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This commit implements the board_fit_image_post_process() function for
the keystone architecture. This function calls into the secure boot
monitor for secure authentication/decryption of the image. All needed
work is handled by the boot monitor and, depending on the keystone
platform, the security functions may be offloaded to other secure
processing elements in the SoC.
The boot monitor acts as the gateway to these secure functions and the
boot monitor for secure devices is available as part of the SECDEV
package for KS2. For more details refer doc/README.ti-secure
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Up till this commit passing NULL as input parameter was allowed, but not
handled properly.
When one passed NULL to one of this function parameters, the code was
executed causing data abort.
However, what is more interesting, the abort was not caught because of code
execution in HYP mode with masked CPSR A bit ("Imprecise Data Abort mask bit).
The TI's AM57xx SoC switch to HYP mode with A bit masked in lowlevel_init.S
due to SMC call. Such operation (by default) is performed in SoC ROM code.
The problem would pop up when one:
- Switch back to SVC mode after disabling LPAE support
- Somebody enables A bit (by executing cpsie a asm instruction)
and then the previously described exception would be caught.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
It also enables commands for cache enable/disable/status.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Recent Linux distributions (e.g. Debian 9) include cross-compilers for
AArch64, but only for the aarch64-linux-gnu triplet only. It can thus
be expected that users will attempt to use the system cross-compiler
(instead of an aarch64-elf variant) to compile U-Boot for their ARMv8
target systems.
One key differences between an aarch64-linux-gnu and an aarch64-elf
compiler are the default settings regarding position-independent: with
the aarch64-linux-gnu compiler, the default will create and use the
global offset table.
This change-set adjusts the list of sections copied on ARMv8 to include
the GOT sections. With this added, the list matches the previous setup
for AArch32 closely.
Note that this is not an 'academic' issue, but was in fact encountered
by our QA during testing of the RK3399-Q7 BSP and resulted in an
early failure of the SPL stage during FDT setup.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Sunchip CX-A99 is a board used in some media players. It features:
An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores)
2 GiB or 4 GiB DDR3 DRAM
AXP808 PMIC
16 GB or 32 GB eMMC
SDIO Wifi/Bluetooth/FM module
SD card slot
1 USB 3.0 connector
2 USB 2.0 connectors
SATA connector
UART connector (internally) for serial console
Ethernet connector (10/100/1000 Mbit/s)
HDMI connector
Composite video and analog audio connector
S/PDIF connector
IR remote control receiver
This patch adds a defconfig for the board. The DRAM settings are as found
in the vendor sys_config.fex file.
It has a preliminary device tree for use until a device tree is accepted
upstream, after which it can be replaced by the upstream version.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
[squash commits, and edited new meanful commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
commit 56b0730157f70dc23d6caff9e7ceb8b377b96b9f upstream.
On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Those DT will be part of 4.10, sync them so we can have our own config.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Add support for the NanoPi NEO Air H3 board from friendlyarm.com . This
board contains WiFi, Bluetooth, 8GB eMMC storage and 512 MB DDR3 ram.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rebase on master]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add the i2c-gpio nodes for fuelgauge and max77693.
There are i2c8 and i2c9.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
This is an weak function present on all archs so we should have it in the
common header file. Remove it from arch-specific headers and add a
function comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The OrangePi PC 2 is a typical SBC with the 64-bit Allwinner H5 SoC.
Add a (64-bit only) defconfig defining the required options to build
the U-Boot proper.
Create a new .dts file for it by including the (32-bit) H3 SoC .dtsi
and changing the differing components accordingly.
This is a preliminary device tree mostly for U-Boot's own sake, it
is expected to be updated once the official DT gets accepted upstream.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[squash the commits, update the commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner H5 Soc is bascially an H3 with high SRAM and ARMv8 cores.
As the peripherals and the pinmuxing are almost identical, we piggy
back on the shared MACH_SUN8I_H3_H5 config symbol.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DRAM controller in the Allwinner H5 SoC is again very similar to
the one in the H3 and A64.
Based on the existing socid parameter, add support for this controller
by reusing the bulk of the code and only deviating where needed.
These new bits set or cleared here and there have been mostly found by
looking at DRAM register dumps after using the H5 boot0 and comparing
them to what we set in the code. So for now it's mostly unclear what
those bits actually mean - hence the missing names and comments.
Also add the delay line parameters taken from the boot0 and libdram
disassembly.
Register setup differences between H5 and H3 are courtesy of Jens Kuske.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Every armv8 board needs the memory map, so change the #ifdef to
ARM64 to avoid enumerating every single board or SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Traditionally Allwinner SoCs have their boot ROM mapped just below 4GB,
while the first SRAM region is mapped at address 0.
With the extended physical memory support of the A80 this was changed,
so the BROM is now at address 0 and the SRAM region starts right behind
this at 64KB. This configuration seems to be called "high SRAM".
Instead of enumerating the SoCs which have copied this configuration,
let's call a spade a spade and introduce a Kconfig option for this setup.
SoCs implementing this (A80, A64 and H5, so far), can then select this
configuration.
Simplify the config header definition on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Instead of enumerating all SoC families that need that bit set, let's
just express this more clearly: The SMP bits needs to be set on
SMP capable ARMv7 CPUs. It's much easier in Kconfig to express it the
other way round, so we use ! CPU_IS_UP and ! ARM64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some Freescale boards used an extra version of the constant to hold the
Generic Timer frequency. This can easily be covered by the now unified
COUNTER_FREQUENCY constant, so remove this extra variable from those
boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Many ARMv8 boards define a constant COUNTER_FREQUENCY to specify the
frequency of the ARM Generic Timer (aka. arch timer).
ARMv7 boards traditionally used CONFIG_TIMER_CLK_FREQ for the same
purpose. It seems useful to unify them.
Since there are less occurences of the latter version, lets convert all
users over to COUNTER_FREQUENCY.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
If we take the liberty to use register r0 to perform our bit set, we
should be nice enough to tell the compiler about it.
Add r0 to the clobber list to avoid potential mayhem.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jagan Teki <jagan@openedev.com>
This patch adds a call to dm_remove_devices_flags() to
announce_and_cleanup() so that drivers that have one of the removal flags
set (e.g. DM_FLAG_ACTIVE_DMA_REMOVE) in their driver struct, may do some
last-stage cleanup before the OS is started.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
expansion ports.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Sort rk3288 boards in alphabetical order.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The (shared) rk3399.dtsi had defined the 'rockchip,vbus-gpio'
properties for each USB 3.0 controller.
As the GPIO usage will vary (e.g. one of those GPIOs shuts down one of
the regulators on the RK3399-Q7) between boards, we move this from the
shared dtsi into the device tree file for the EVB board which these
GPIO definitions match.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399-Q7 is a system-on-module featuring the Rockchip RK3399
in a Qseven-compatible form-factor.
These changes add a device-tree describing the board and its
interfaces for basic functionality (e.g. GbE, SPI, eMMC, SD-card).
This includes the following changes from the original development:
* dts: rk3399-puma: include DTS for RK3399-Q7 SoM in the Makefile
* dts: rk3399-puma: add gmac for the RK3399-Q7
This change enables the Gigabit Ethernet support on the RK3399-Q7.
* dts: rk3399-puma: use serial0 for stdout
* dts: rk3399-puma: prepare the sdmmc node for SPL booting
* dts: rk3399-puma: enable spi1 and spi5, add /spi1/spiflash
The RK3399-Q7 (Puma) unsually (this is a build-time option for
customised boards) has an on-module SPI-flash connected to SPI1.
As of today, this is a Winbond W25Q32DW (32MBit) device.
The SPI5 controller is routed to the Q7 edge connector and provides
general-purpose SPI connectivity for customer base-boards.
With some minor improvements on integration into our outbound tree
- explicitly modelled the SPI flash as 'spiflash' under spi0
[dts: rk3399-puma: explicitly model spi-flash under spi1]
- renamed the aliases to spi0 and spi1 to allow easier use of
commands and legacy (SPL) infrastructure... i.e. the controllers
will be 0 and 1 for 'sf probe', 'sspi', etc.
[dts: rk3399-puma: rename aliases to number spi as 0 and 1 for commands]
* dts: rk3399-puma: include SPI in the spl-boot-order property
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
For the initial validation of the RK3399-Q7 (Puma), the DDR3 has been
clocked at 666MHz (i.e. DDR3-1333) using the same (safe) settings as
used in Rockchip's MiniLoader.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399 does not have any boot selection pins and the BootROM probes
the boot interfaces using the following boot-order:
1. SPI
2. eMMC (sdhci in DTS)
3. SD card (sdmmc in DTS)
4. USB loader
For ease of deployment, the SPL stage should mirror the boot order of
the ROM and use the same probing order (assuming that valid images can
be detected by SPL) unless instructed otherwise. The boot-order can
then be configured via the 'u-boot,spl-boot-order' property in the
chosen-node of the DTS.
While this approach is easily extensible to other boards, it is only
implemented for the RK3399 for now, as the large SRAM on the RK3399
makes this easy to fit the needed infrastructure into SPL and our
production setup already runs with DM, OF_CONTROL and BLK in SPL.
The new boot-order property is expected to be used in conjunction with
FIT images (and all legacy image formats disabled via Kconfig).
A boot-sequence with probing and fallthroughs from SPI via eMMC to SD
card (i.e. &spiflash, &sdhci, &sdmmc) has been validated on the RK3399-Q7.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Rock is a RK3188 based single board computer by Radxa.
Currently it still relies on the proprietary DDR init and
cannot use the generic SPL, but at least is able to boot
a linux kernel and system up to a regular login prompt.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix sort order in defconfig, enable CONFIG_SPL_TINY_MEMSET:
Signed-off-by: Simon Glass <sjg@chromium.org>
firefly have a usb host. add dts node to provide power supply
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This change adds the gmac node (i.e. the GMAC Ethernet controller) as
defined in the Linux DTS.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The GMAC in the RK3399 is very similar to the RK3288 variant (i.e. it
is a Designware GMAC core and requires similar configuration as the
RK3288 to switch it to RGMII and set up the TX/RX delays for Gigabit).
The key difference is that the register offsets (within the GRF block)
and bit-offsets (within those registers) used to hold the configuration
differ between the various RK32/33 CPUs.
This change refactors the gmac_rockchip.c driver to use a function
table (selected via driver_data) to factor out these differences. Each
function's implementation then matches the underlying processor.
Some collateral changes are needed in the definitions describing the
bits and offsets in the GRF are needed to prefix each set of symbolic
constants with the SoC name to avoid name clashes... and in doing so,
the shifts for masks and constants have been moved into the header
files for readability (and to make it easier to stay below 80 chars).
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed commit message typo s/factor our/factor out/:
Signed-off-by: Simon Glass <sjg@chromium.org>
To add GMAC (Gigabit Ethernet) support (limited to RGMII only at this
point), we need support for additional pin-configuration. This commit
adds the pinctrl support for GMAC in RGMII signalling mode:
* adds a PERIPH_ID_GMAC and the mapping from IRQ number to PERIPH_ID
* adds the required defines (in the GRF support) for configuring the
GPIOC pins for RGMII
* configures the RGMII pins (in GPIOC) when requested via pinctrl
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
An earlier upstream change contained an unconditional debug message
which would show up as a message similar to the following in the
U-Boot startup (after the ATF and before the U-Boot banner):
time 159f019, 0
This commit removes this message (instead of making if conditional on
being a debug-build), as it doesn't pertain to any initialisation done
in this file.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Designware HDMI controller and phy are used in other SoCs as well. Split
out platform independent code.
DW HDMI has 8 bit registers but they can be represented as 32 bit
registers as well. Add support to select access mode.
EDID reading code use reading by blocks which is not supported by other
SoCs in general. Make it more general using byte by byte approach, which
is also used in Linux driver.
Finally, not all DW HDMI controllers are accompanied with DW HDMI phy.
Support custom phys by making controller code independent from phy code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The armclk starts in slow mode (24MHz) on the rk3188, which results in U-Boot
startup taking a lot of time (U-Boot itself, but also the rc4 decoding done
in the bootrom).
With default pmic settings we can always reach a safe frequency of 600MHz
which is also the frequency the proprietary loader left the armclk at,
without needing access to the systems pmic.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The armclk starts in slow mode (24MHz) on the rk3188, which makes the whole
startup take a lot of time. We therefore want to at least move to the safe
600MHz value we can use with default pmic settings.
This is also the freqency the proprietary sdram-init leaves the cpu at.
For boards that have pmic control later in u-boot, we also add the option
to set the maximum frequency of 1.6GHz, if they so desire.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
In the beginning, we did SPL -> TPL -> U-Boot, but after clarification
of the real ordering swapped SPL and TPL.
It seems some renames were forgotten and may confuse future readers, so
also swap these to reflect the actual ordering.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
There was still a static ram value set in the rk3188-board from the
time where we didn't have actual sdram init code.
Now the sdram init leaves the ram information in SYS_REG2 and we can
decode it similarly to the rk3288.
Right now we have two duplicates of that code, which is still ok and
doesn't really count as common code yet, but if we get a third copy
at some point from a newer soc, we should think about moving that to
a more general position.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Right now we're setting the wrong value of 0 as base in the ram_info struct,
which is obviously wrong for the rk3188. So instead set the correct value
we already have in CONFIG_SYS_SDRAM_BASE.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Commit c67c8c604b ("board_init.c: Always use memset()") dropped the naive
memset alternative from board_init_f_init_reserve.
So activate CONFIG_TPL_LIBGENERIC for that common memset implementation.
We cannot use the ARCH-specific memset, as that would incur 200bytes of
additional TPL size, space we do not have.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SPL binary needs to be prefixed with the boot magic ('RK33' for
the RK3399) on the Rockchip platform and starts execution of the
instruction word following immediately after this boot magic.
This poses a challenge for AArch64 (ARMv8) binaries, as the .text
section would need to start on the odd address, violating natural
alignment (and potentially triggering a fault for any code that
tries to access 64bit values embedded in the .text section).
A quick and easy fix is to have the .text section include the 'RK33'
magic and pad it with a boot0 hook to insert 4 bytes of padding at the
start of the section (with the intention of having mkimage overwrite
this padding with the appropriate boot magic). This avoids having to
modify the linker scripts or more complex logic in mkimage.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
This includes Marvell mvpp2 patches with the ethernet support for the
ARMv8 Armada 7k/8k platforms. The ethernet patches are all acked by Joe
and he is okay with me pushing them via the Marvell tree.
Change the buck8's min-microvolt to 750000.
Whent thor protocol is used, board_usb_init() should be tried to set to
750000. But it was returned -EINVAL, because '750000' too lower than
2850000. (thor command doesn't work fine because of this problem.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Trats has the i2c gpio for fuel-gaugge.
This patch s for preparing to use the fuel-gauge.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock
loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0
register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds board support for the Toradex Apalis TK1 a computer on
module which can be used on different carrier boards.
The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot, environment storage and Toradex factory config block
- Gigabit Ethernet
- MMC/SD cards (both MMC1 as well as SD1 slot)
- USB client/host (dual role OTG port as client e.g. for DFU/UMS or host,
other two ports as host)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The default configuration for the COMPHY-0 port should be 1G, as its
used as 1G SGMII connection. This change is necessary to get the
MAC2 port (SGMII) working on this DB.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds the description of the PPv2.2 hardware block for the
Marvell Armada 7K and Armada 8K processors, and their corresponding Armada
7040 and 8040 Development boards.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Tests have shown that on some boards the default width of the
configuration pulse for the PEX link detection might lead to
non-established PCIe links (link down). Especially under certain
conditions (higher temperature) and with specific PCIe devices
(in the case on the theadorable board its a Atheros PCIe WLAN
device). To enable a board-specific detection pulse width this weak
array "serdes_pex_pulse_width[4]" is introduced which can be
overwritten if needed by a board-specific version. If the board
code does not provide a non-weak version of this variable, the
default value will be used. So nothing is changed from the
current setup on the supported board.
Many thanks to Adam from Marvell for all his insights here and
his suggestion about testing with a changed detection pulse width.
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Adam Shobash <adams@marvell.com>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add pin control nodes for North and South bridges to
Armada-37xx DT
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added A8040 dts file for community board MACCHIATIBin.
The patch includes the following features:
AP - Serial console (connected to onboard FTDI usb to serial)
CP0 - PCIe x4, SATA, I2C and 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy)
CP1 - Boot SPI, USB3 host, 2xSATA, 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy),
SGMII connected to onboard 1512 1Gbps copper phy,
and additional SGMII connected to SFP
(default 1Gbps can be configured to 2.5Gbps).
Network interface naming -
egiga0 - CP0 KR
egiga1 - CP1 KR
egiga2 - CP1 RJ45 1Gbps connector (recommended for TFTP boot)
egiga3 - CP1 SFP default 1Gbps and can be modified to 2.5Gbps
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Layerscape Chassis-2 have PCIe device, some platform devices and
DPAA1 devices which will use stream-ids for iommu level isolation
as they are behind SMMU.
This patch defines the stream-ids for Chassis-2 devices. DPAA1 is
reserved for future use.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080a, LS1088a and LS2088a SOCs are based on Chassis-3 and shared
same stream-id partitioning. This patch rewords the definition to
support all these SOCs.
Also have changes in description about iommu-map property updates
in PCI node.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The stream ID allocation for Chasis 3.0 devices can be shared among
LS1088, LS2088 and LS2080.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
USB requires 100MHz clock. On LS1012A, a dedicated 100MHz is provided
instead of SYSCLK (125MHz). Skipping checking SYSCLK for FDT fixup.
Signed-off-by: Yingxi Yu <yingxi.yu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS2088A series SoCs has different physical memory map address and
CCSR registers address against LS2080A series SoCs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This i2c errata only applies to LS2080A and its variants, namely
LS2080A, LS2085A and LS2088A.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SerDes information is not necessary to be present in RCWSR29 register.
It may vary from SoC to SoC.
So Avoid RCWSR28 register hard-coding.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A009635 is valid only for LS2080A SoC and its
personality. Add SoC svr check.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For validating images from uboot (Such as Kernel Image), either keys
from SoC fuses can be used or keys from a verified table of public
keys can be used. The latter feature is called IE Key Extension
Feature.
For Layerscape Chasis 3 based platforms, IE table is validated by
Bootrom and address of this table is written in scratch registers 13
and 14 via PBI commands.
Following are the steps describing usage of this feature:
1) Verify IE Table in ISBC phase using keys stored in fuses.
2) Install IE table. (To be used across verification of multiple
images stored in a static global structure.)
3) Use keys from IE table, to verify further images.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moved the ifdef into ppa.h and removed the duplicated macros.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add header address for PPA to be validated during ESBC phase for LS2080A
platform based on Layescape Chasis 3.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since the lpc32xx i2c driver does not yet support the devicetree bindings,
this structure is also needed by the board file as the hardware description
is done there.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This patch adds a reset controller implementation for STMicroelectronics
STi family SoCs; it allows a group of related reset like controls found
in multiple system configuration registers to be represented by a single
controller device.
Driver code has been mainly extracted from kernel
drivers/reset/sti/reset-stih407.c
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Select missing BOARD_LATE_INIT from configs/ to
respective targets on arch area for Engicam imx6 boards.
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Tests have shown that on some boards the default width of the
configuration pulse for the PEX link detection might lead to
non-established PCIe links (link down). Especially under certain
conditions (higher temperature) and with specific PCIe devices
(in the case on the theadorable board its a Atheros PCIe WLAN
device). To enable a board-specific detection pulse width this weak
array "serdes_pex_pulse_width[4]" is introduced which can be
overwritten if needed by a board-specific version. If the board
code does not provide a non-weak version of this variable, the
default value will be used. So nothing is changed from the
current setup on the supported board.
Many thanks to Adam from Marvell for all his insights here and
his suggestion about testing with a changed detection pulse width.
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Adam Shobash <adams@marvell.com>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add pin control nodes for North and South bridges to
Armada-37xx DT
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added A8040 dts file for community board MACCHIATIBin.
The patch includes the following features:
AP - Serial console (connected to onboard FTDI usb to serial)
CP0 - PCIe x4, SATA, I2C and 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy)
CP1 - Boot SPI, USB3 host, 2xSATA, 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy),
SGMII connected to onboard 1512 1Gbps copper phy,
and additional SGMII connected to SFP
(default 1Gbps can be configured to 2.5Gbps).
Network interface naming -
egiga0 - CP0 KR
egiga1 - CP1 KR
egiga2 - CP1 RJ45 1Gbps connector (recommended for TFTP boot)
egiga3 - CP1 SFP default 1Gbps and can be modified to 2.5Gbps
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable SPL_DM on all AM43xx based platforms
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable DM_I2C/SPI/ETH for all AM43XX based boards.
Enable it using imply keyword so that a user can
disable this when not needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add u-boot specific dtsi for am43xx-gp-evm so
that it will be used for SPL.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add u-boot specific dtsi so that this will be
included automatically while building dts.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
To make SPL_OF_CONTROL work on OMAP2+ SoCs, _image_binary_end must be
defined in the linker script along with CONFIG_SPL_SEPARATE_BSS.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for the Broadcom Northstar2 SoC and SVK (bcm958712k). The
BCM5871X is a series of quad-core 64-bit 2GHz ARMv8 Cortex-A57
processors targeting a broad range of networking applications.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Currently, AM43xx just re-uses the version strings from AM33xx which is
wrong; the actual values for AM43xx are different. Fix this by adding
a separate version string array for AM43xx and use this instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
PRU ethernet MAC address range is present in the
board EEPROM. Parse it and setup eth?addr
environment variables.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Non OMAP platforms i.e. Keystone will also need to use the board
EEPROM helpers so let's make the macro platform independent.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
GPIO_TO_PIN(bank, bank_gpio) returns the GPIO index
from the GPIO bank number and bank's GPIO offset number.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Introduce device tree support.
dts from kernel commit c4f3f22edd Merge tag 'linux-kselftest-4.11-rc1'
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
To keep a consistent MMC device mapping in SPL and in u-boot, let's
register the MMC controllers the same way in u-boot and in the SPL.
In terms of boot time, it doesn't hurt to register more controllers than
needed because the MMC device is initialized only prior being accessed for
the first time.
Having the same device mapping in SPL and u-boot allows us to use the
environment in SPL whatever the MMC boot device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137 ("ARM:
mx6: move to a standard arch/board approach").
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
According to the MX7D fuse map the following speed grades are available:
800 MHz
500 MHz
1000 MHz
1200 MHz
So simply return the real frequency that corresponds to the speed grade.
With this change we see on boot:
CPU: Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
According to the MX7D fuse map the speed grade of the parts, which
return '1' is 500MHz instead of 850MHz, so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This is needed to make the UMS command work again as it fails with the
following error:
BIOS> ums 0 mmc 0
UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x748000
g_dnl_register: failed!, error: -19
ERROR: g_dnl_register failed
at cmd/usb_mass_storage.c:179/do_usb_mass_storage()
That's because usb_setup_ehci_gadget() function is looking for the usb
device using the req_sed number.
This change makes the usb device have a req_seq number and the UMS
command work again:
BIOS> ums 0 mmc 0
UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x748000
CTRL+C - Operation aborted
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.
U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1
U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)
CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
add basic clock driver support for stm32f7 to enable clocks required by
the peripherals.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch cleans the code by using instructions allowed for armv7m as well as
other Arm archs.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
We only support cores that do Thumb-1 or later. So we add a comment to
explain this and remove the architecture test.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 19a5944fcd ("mvgbe: remove setting of ethaddr within the
driver") removed the usage of get_random_hex() from the mvgbe driver
about six years ago. However the prototype of that function survived
till today in some kirkwood header file.
Remove that prototype and the CONFIG_MD5 dependency triggered by that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Instead of initializing 'struct src' to SRC_BASE_ADDR on
every function better to have global define macro.
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Use meaningful macros IMX6_BMODE_*, instead of numerical
number in boot mode detection code.
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
BOOT_CFG1[7:4] the NAND boot mode selection is done
only when BOOT_CFG1[7] is 1 hence update the NAND
boot mode detection bit case. This information available
on Table 8-11. NAND Boot eFUSE Descriptions, from IMX6DQRM.
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
For i.MX6, the bootmode determine code is part of spl_boot_device,
but there is might be a possibility for other part the code need to
check the desired boot mode for adding new functionalities like
modeboot env variable, or changing boot order etc.
So introduced imx6_src_get_boot_mode which actually reading the
boot mode register for desired modes.
More cleanup will be add in future patches.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Boot from MMC:
-------------
U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33)
Trying to boot from MMC1
U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100)
CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 33C
Reset cause: POR
Model: Engicam Is.IoT MX6UL Starterkit
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
isiotmx6ul>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CAAM clock functions, SEC_CONFIG[1] fuse checking, and default CSF
size for HAB support boot on mx7ulp.
Users need to uncomment the CONFIG_SECURE_BOOT in mx7ulp_evk.h to build
secure uboot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Drop CONFIG_LPUART_32B_REG.
Move the register structure to a common file include/fsl_lpuart.h
Define lpuart_serial_platdata structure which includes the reg base and flags.
For 32Bit register access, use lpuart_read32/lpuart_write32 which handles
big/little endian.
For 8Bit register access, still use the orignal code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Add lpi2c driver for i.MX7ULP.
Need to enable the two options to use this driver:
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_IMX_LPI2C=y
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add the iomux pins header file from iomux tool team. Change the IOMUXC0 pins
to add IOMUX_CONFIG_MPORTS flags.
Note: The IOMUXC0 offset provided in this file is from 0xD000, this is not
aligned with IOMUXC0 base address. We have adjusted the IOMUXC0 base address
to aligin with it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update the mxc_ocotp driver to support i.MX7ULP.
The read/write sequence has some changes due to
PDN and OUT_STATUS registers added and TIME register is
removed. Also update the bank size and number.
Add is_mx7ulp macro in sys_proto.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add the imx_rgpio2p driver for Rapid GPIO2P controllers on i.MX7ULP.
Have added all ports on RGPIO2P_0 and RGPIO2P_1.
The configurations CONFIG_IMX_RGPIO2P and CONFIG_DM_GPIO must be set
to y to enable the drivers.
To use the GPIO function, the IBE and OBE needs to set in IOMUXC.
We did not set the bits in driver, but leave them to IOMUXC settings
of the GPIO pins. User should use IMX_GPIO_NR to generate the GPIO number
for gpio APIs access.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Implement the i2c clock enable and get function for mx7ulp. These
functions are required by imx_lpi2c driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Implement soc level functions to get cpu rev, reset cause, enable cache,
etc. We will disable the wdog and init clocks in s_init at very early u-boot
phase.
Since the we are seeking the way to get chip id for mx7ulp, the get_cpu_rev
is hard coded to a fixed value. This may change in future.
Reuse some code in imx-common.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a clock framework to support SCG1/PCC2/PCC3 for A7 to support get/set
clock source, divider, clock rate and parent source.
Users need to include pcc.h to use the APIs to for peripherals clock. Each
peripheral clock is defined in enum pcc_clk type.
SCG relevants APIs are defined in scg.h which supports clock rate get, PLL/PFD
enablement and settings, and all SCG clock initialization. User need use enum
scg_clk to access each clock source.
In clock.c, we initialize necessary clocks at u-boot s_init and implement the
clock functions used by driver modules to operate clocks dynamically.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a new driver under ULP directory to support its IOMUXC
controllers. The ULP has two IOMUXC, the IOMUXC0 is used
for M4 domain, while IOMUXC1 is for A7. We set IOMUXC1 as
the default IOMUX in this driver. Any pins in IOMUXC0 needs
to configure with IOMUX_CONFIG_MPORTS in its mux_mode field.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add imx-regs.h for i.MX7ULP registers addresses definitions and some
registers structures.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
i.MX7ULP is a new series SoC which has different architecture
from previous i.MX platforms. Create a new cpu folder for it,
and add it to Kconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Tinker board have a usb host. add dts node to provide power supply.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable gmac interface for rk3288 board dts.
use "okay" not "ok"
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
evb-rk3328 is an evb from Rockchip based on rk3328 SoC:
- 2 USB2.0 Host port;
- 1 USB3.0 Host port;
- 1 HDMI port;
- 2 10/100M eth port;
- 2GB ddr;
- 16GB eMMC;
- UART to USB debug port;
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add rk3328 pinctrl driver and grf/iomux structure definition.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
RK3328 is a SoC from Rockchip with quad-core Cortex-A53 CPU.
It supports two USB2.0 EHCI ports. Other interfaces are very
much like RK3288, the DRAM are 32bit width address and support
address from 0 to 4GB-16MB range.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add empty arch/arm/mach-rockchip/rk3328/Kconfig to avoid build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add dts binding header for rk3328, files origin from kernel.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable all the CONFIGs which need by SPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Drop CONFIG_ROCKCHIP_DWMMC for now due to build error:
Move changes to arch/arm/mach-rockchip/Kconfig to this patch:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add SPL support for rk3399, default with of-platdata enabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop Kconfig changes to fix build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add syscon and dmc node, and 'u-boot,dm-pre-reloc' option for
required driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
RK3399 support DDR3, LPDDR3, DDR4 sdram, this patch is porting from
coreboot, support 4GB lpddr3 in this version.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Added rockchip: tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
The rk3188 needs 3 U-Boot stages: a tpl living in 1KB of sram, a spl
the resides in the rest of the sram and loads the regular U-Boot living
in regular ram.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
The sdram controller blocks are very similar to the rk3288 in utilizing
memory scheduler, Designware uPCTL and Designware PUBL blocks, only
limited to one bank instead of two.
There are some minimal differences when setting up the ram, so it gets
a separate driver for the rk3188 but reuses the driver structs, as there
is no need to define the same again.
More optimization can happen when the modelling of the controller parts
in the dts actually follow the hardware layout hopefully at some point
in the future.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add the core architecture code for the rk3188.
It doesn't support the SPL yet, as because of some
unknown error it doesn't start yet.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Drop these defines from rk3188_common.h
CONFIG_GENERIC_MMC, CONFIG_BOUNCE_BUFFER, CONFIG_DOS_PARTITION
CONFIG_PARTITION_UUIDS, CONFIG_CMD_PART:
Signed-off-by: Simon Glass <sjg@chromium.org>
The rk3188 shares a lot of peripherals with the rk3066 and thus
has a common include called rk3xxx.dtsi. Add both this one and
the specialized rk3188 on top of it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add a driver for setting up and modifying the various PLLs and peripheral
clocks on the RK3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
PMU is the power management unit and GRF is the general register file. Both
are heavily used in U-Boot. Add header files with register definitions.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
So far spl-boards have declared the back_to_brom() function as simple
extern in the files themself. That doesn't scale well if every boards
defines this on its own.
Therefore move the declarations to a bootrom header.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Right now the ROCKCHIP_SPL_BACK_TO_BROM option both triggers
compilation of the bootrom hook-code as well as enabling the
behaviour of loading the full U-Boot via the boot.
New added socs may always need the bootrom code, while still
being able to decide between loading U-Boot regularly or via
the bootrom separately.
So move the compilation of the bootrom code to a hidden option
that gets selected by ROCKCHIP_SPL_BACK_TO_BROM, but can also
be selected by other parts.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
The sdram IP blocks used on rk3066, rk3188 and rk3288 are very similar
and we want to unify things once all 3 work as expected.
Therefore try to keep the rk3288 sdram driver in line by applying the
general review comments received for the rk3188 variant to it as well.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Use defines to describe the bit shifts used to create the
table for ddrconf register values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
rk3399 has different syscon registers which may used in spl,
add to support rk3399 spl.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
rk3399 grf register bit defenitions should locate in header
file, so that not only pinctrl can use it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Use spl_early_init() to make sure that early malloc() is initialised. This
fixes booting on firefly-rk3288, for example.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
This is a 96Board compliant board based on STiH410 SoC:
- 1GB DDR
- On-Board USB combo WiFi/Bluetooth RTL8723BU
with PCB soldered antenna
- Ethernet 1000-BaseT
- SATA
- HDMI
- 2 x USB2.0 type A
- 1 x USB2.0 type micro-AB
- SD card slot
- High speed connector (SD/I2C/USB interfaces)
- Low speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This device tree has been extracted from v4.9 kernel
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add SDHCI host controller found on STMicroelectronics SoCs
On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.
This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.
W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
As no gpio.h is defined in arch/arm/include/asm/arch-stih410,
to avoid compilation failure, do not include asm/arch/gpio.h.
This is needed for example when including sdhci.h, which include
asm/gpio.h>.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP
is common across other STMicroelectronics SoCs
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The STiH410 is an advanced multi-HD AVC processor with 3D
graphics acceleration and 1.5-GHz ARM Cortex-A9 SMP CPU
part of the STiH407 family.
It has wide connectivity including USB 3.0, PCI-e, SATA
and gigabit ethernet.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The SysTick is a 24-bit down counter that is found on all ARM Cortex
M3, M4, M7 devices and is always located at a fixed address.
The number of reference clock ticks that correspond to 10ms is normally
defined in the SysTick Calibration register's TENMS field. However, on some
devices this is wrong, so this driver allows the clock rate to be defined
using CONFIG_SYS_HZ_CLOCK.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Vikas MANOCHA <vikas.manocha@st.com>
The workaround for ARM errata 725233 had been lost since
commit 45bf05854b (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Boards with OMAP3530 SoC fail to boot since commit bd2c4522c2
("ti: armv7: enable EXT support in SPL (using ti_armv7_common.h)")
because it enabled the use of Thumb2 for the SPL.
Experiments have shown that the deadlock happens in the
prcm_init() function from 'arch/arm/mach-omap2/omap3/clock.c'.
This patch enforces the compilation of clock.c source file in
ARM mode and makes the deadlock disappear. We are yet to figure
out the root cause of the problem. Still this is somewhat
better than having non-bootable boards for years.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Raw uboot image is used in place of FIT image in secure boot.
The maximum allocated size of raw u-boot bin is 1MB in memory map.
Hence , CONFIG_SYS_MONITOR_LEN has been modified to 1 MB.
The bootscript (BS_ADDR) and its header (BS_HDR_ADDR) offset on
MMC have also been modified to accommodate the increase in uboot size.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Reviewed-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
VID support in NXP layerscape Chassis-3 (lsch3) compilant SoCs like
LS2088A, LS2080A differs from existing logic.
-VDD voltage array is different
-Registers are different
-VDD calculation logic is different
Add new function adjust_vdd() for LSCH3 compliant SoCs
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Arpit Goel <arpit.goel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Read DMA operations causes CRC error on armv8 chassis 2 platforms
due to the erratum A-010635.
In order to support sata on these platforms, ECC needs to be disabled.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.
Signed-off-by: York Sun <york.sun@nxp.com>
Function mmu_change_region_attr() is added to change existing mapping
with updated PXN, UXN and memory type. This is a break-before-make
process during which the mapping becomes fault (invalid) before final
attributres are set.
Signed-off-by: York Sun <york.sun@nxp.com>
Early MMU improves performance especially on emulators. However, the
early MMU is left enabled after the first stage of SPL boot. Instead
of flushing D-cache and dealing with re-enabling MMU for the second
stage U-Boot, disabling it for SPL build simplifies the process. The
performance penalty is unnoticeable on the real hardware. As of now,
SPL boot is not supported by existing emulators. So this should have
no impact on emulators.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch follows the break-before-make process when making changes
to MMU table. MMU is disabled before changing TTBR to avoid any
potential race condition.
Signed-off-by: York Sun <york.sun@nxp.com>
Update mapping with actual DDR size. Non-existing memory should not
be mapped as "normal" memory to avoid speculative access.
Signed-off-by: York Sun <york.sun@nxp.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
Fix warnings reported when built with W=1, by DTC 1.4.2 or later:
Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Linux Commit 9c0da3cc61f1 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated") declared that skeleton.dtsi was deprecated.
Move the memory node below to suppress warnings of FDTGREP.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 04cd4e7215 ("ARM: uniphier: remove DRAM base address from
board parameters") accidentally unset the DRAM_SPARSE flag, and
changed the physical map of the DRAM channels. Revive the original
behavior.
Fixes: 04cd4e7215 ("ARM: uniphier: remove DRAM base address from board parameters")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Shunji Sato <sato.shunji@socionext.com>
Some initialization was unintentionally being skipped on omap5.
Fixes: f5af0827f2 ("arm: omap-common: Guard some parts of the code with CONFIG_OMAP44XX/OMAP54XX")
Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently nandecc returns zero even if underlaying
omap_nand_switch_ecc function fails. Fix that by
propagating error returned to command return value.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config. We now just select these once at the higher level in Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the default y options under arch/arm/mach-omap2/omap4/Kconfig to be
using imply instead in arch/arm/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the default y options under arch/arm/mach-omap2/omap3/Kconfig to be
using imply instead in arch/arm/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
The option that we had set in board/ti/common/Kconfig as default y are
best done with imply under the appropriate main Kconfig option instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
These particular SPL options are part of what the ROM provides, but for
compatibility with how we have previously used them, move them to being
implied by the board being selected.
Signed-off-by: Tom Rini <trini@konsulko.com>
do_smhload was using a ulong to store the return value from
smh_load_file. That returns an int, where -1 indicates an error. As a
ulong will never be negative, smh_load_file errors were not detected and
so_smhload always returned zero.
Also, when errors were spotted, do_smhload was returning 1, rather than
the enumeration CMD_RET_FAILURE (which is also 1).
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
In some cases this is absolutely required, so select this for some secure
features. This also requires migration of RSA_FREESCALE_EXP
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Saksham Jain <saksham.jain@nxp.freescale.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As part of the startup process for boards using the SPL, we need to
call spl_relocate_stack_gd. This is needed to set up malloc with its
DRAM buffer.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Current ARM assembler helper for the 'return to caller' pseudo-instruction
turns 'ret lr' into 'mov pc, lr' for ARMv5TE. This causes the core to remain
in its current ARM state even when the routine doing the 'ret' was called
from Thumb-1 state, triggering an undefined instruction exception.
This causes early run-time failures in all boards compiled using the Thumb-1
instruction set (for instance the Open-RD family).
ARMv5TE supports 'bx lr' which properly implements interworking and thus
correctly returns to Thumb-1 state from ARM state.
This change makes 'ret lr' turn into 'bx lr' for ARMv5TE.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
After we authenticate/decrypt an image we need to flush the caches
as they may still contain bits of the encrypted image. This will
cause failures if we attempt to jump to this image.
Reported-by: Yogesh Siraswar<yogeshs@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Re-use of routines embedded in the Boot ROM requires a function
pointer table for each SoC. This is not nice in terms of the
maintainability in a long run.
Implement simple eMMC load APIs that are commonly used for LD11,
LD20, and hopefully future SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For LD11 and LD20 SoCs, the RST_n pin is asserted by default. If
the EXT_CSD[162], bit[1:0] (RST_n_ENABLE) is fused, the eMMC device
would stay in the reset state until its RST_n pin is deasserted by
software.
Currently, this is cared by an ad-hoc way because the eMMC hardware
reset provider is not supported in U-Boot for now. This code should
be re-written once the "mmc-pwrseq-emmc" binding is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If the DRAM clock duty does not meet the allowable tolerance,
it is marked in an efuse register. If the register is fused,
the boot code should compensate for the DRAM clock duty error.
Signed-off-by: Kotaro Hayashi <hayashi.kotaro@socionext.com>
[masahiro: simplify code, add git-log]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This parameter is redundant because we can know the number of
channels by checking if dram_ch[2].size is zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The current implementation has ugly switch statements here and there,
and duplicates similar code. Rework it using table lookups for SoC
data and reduce code duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The spl_boot_mode() is unrelated to the other code in this file.
Besides, this function is only called from common/spl/spl_mmc.c,
so it is reasonable to guard with CONFIG_SPL_MMC_SUPPORT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, arch/arm/mach-uniphier/boot-mode/boot-mode.c is messed up
with unrelated code; there is no reason why the "mmcsetn" command
must be placed in this file.
Split out the MMC code into arch/arm/mach-uniphier/mmc-first-dev.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit 26b09c022a ("ARM: uniphier: move SBC and Support Card
init code to U-Boot proper"), SPL does not need pin-mux settings for
the System Bus.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The base address of each DRAM channel can be calculated from other
parameters, so does not need hard-coding. What we need is the size
of each DRAM channel and DRAM_SPARSE flag to decide the start address
of DRAM channel 1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit 26b09c022a ("ARM: uniphier: move SBC and Support Card
init code to U-Boot proper"), the System Bus is initialized by
board_init(). The show_board_info() is called from board_init_f()
by default, so the revision register of the Micro Support Card may
not be accessed at this point. Show its revision after the System
Bus is initialized.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now the "for" loop here iterates on the detected memory banks.
It must skip unused DRAM banks.
Fixes: c995f3a3c5 ("ARM: uniphier: use gd->bd->bi_dram for memory reserve on LD20 SoC")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If SG_MEMCONF_CH2_DISABLE bit is set, the DRAM channel 2 is unused.
The register settings for the ch2 should be ignored.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When using early malloc the allocated memory can overflow into the SRAM
scratch space, move NON_SECURE_SRAM_IMG_END down a bit to allow more
dynamic allocation at the expense of a slightly smaller maximum image
size.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Added SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to Kconfig.
Due to SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION being moved to
Kconfig the board defconfigs for db-88f6820-gp_defconfig
kc1_defconfig and sniper_defconfig need to be updated.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
the socfpga bootrom supports mmc booting from either a raw image
starting at 0x0, or from a partition of type 0xa2. This patch
adds support for locating the boot image in the first type 0xa2
partition found.
Assigned a partition number of -1 will cause a search for a
partition of type CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_TYPE
and use it to find the u-boot image
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
When the node 'reserved-memory' is not defined in the DT we fail
to add needed properties. We also fail to move 'offs' to point to
the new node. Fix these here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move the zynq to clock framework and remove unused functions as well as
the CONFIG_ZYNQ_PS_CLK_FREQ configuration.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynq_clk_get_name function is only used once inside the clock
driver. Replace the function call with the one-line code.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The clock names are static and correspond to the clock id. Separate
them from the dynamic filled clock array.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If available use the clock framework to calculate the clock rate of the
zynq timer.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If available use the clock framework to set the tx clock rate of the
zynq ethernet controller.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The gem[0-1]_rclk_ctrl registers control the source of the rx clock,
control and data signals and configure via ps7_init function. Don't
overwrite the register with the default value.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Miniarm is the internal project code. Now it is officially named Tinker board.
So rename it.
Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
miniarm board use lpddr3
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Added 'rockchip:' prefix to subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
Change-Id: I84c3679dab2dbd8d01c1ebfd22220946d07c03cd
To use driver-model adds the pmic node for max8997.
This is used as kernel device-tree in Linux.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_CMD_ZIP is not defined by any board. I am moving
CONFIG_CMD_UNZIP to defconfig files except UniPhier SoC family.
I am the maintainer of UniPhier platform, so I know "select CMD_UNZIP"
is better for this platform.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
There are two typos in the comment "invalide i-cache is enabled".
We can fix it by
invalide -> invalidate
is -> if
Or, if we want to match the comment to the code, we can say
"skip invalidating i-cache if disabled".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As reported in [1], rename the k2* dts files to keystone-* files
this will force consistency throughout.
Script for the same (and hand modified for Makefile and config
files):
for i in arch/arm/dts/k2*
do
b=`basename $i`;
git mv $i arch/arm/dts/keystone-$b;
sed -i -e "s/$b/keystone-$b/g" arch/arm/dts/*[si]
done
This is similar to linux kernel commit 5edafc29829bc ("ARM: dts: k2*: Rename
the k2* files to keystone-k2* files")
[1] http://marc.info/?l=linux-arm-kernel&m=145637407804754&w=2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AArch64 has a zero register (xzr). Use it instead of x2.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
The mpuclk register in the Altera group of the clock manager
divides the mpu_clk that is generated from the C0 output of the main
pll.
Without this patch, the default value of the register is 1, so the mpuclk
will always get divided by 2 if the correct value is not set. For example,
on the Arria5 socdk board, the MPU clock is only 525 MHz, and it should be
1.05 GHz.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add support for programmable MAC impedance configuration and
fix typo in DT impedance parameters names.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP output clock.
Update sys_info->freq_localbus to represent IFC input clock with
value constant divisor of platform clock.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PPA binary needs to be relocated on secure DDR, hence marking out
a portion of DDR as secure if CONFIG_SYS_MEM_RESERVE_SECURE flag
is set
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch implements secure booting for the mvebu architecture.
This includes:
- The addition of secure headers and all needed signatures and keys in
mkimage
- Commands capable of writing the board's efuses to both write the
needed cryptographic data and enable the secure booting mechanism
- The creation of convenience text files containing the necessary
commands to write the efuses
The KAK and CSK keys are expected to reside in the files kwb_kak.key and
kwb_csk.key (OpenSSL 2048 bit private keys) in the top-level directory.
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
ddaa905 ("arm: mvebu: Add DM (driver model) support") removed the
assignment of the gd pointer, but kept the (now superfluous) declaration
of the gd pointer.
Remove this declaration.
Signed-off-by: Reinhard Pfau <pfau@gdsys.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Allow boards to do some initialization when PCIe comes up.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Armada 38x has four PCI ports, not three.
The optimization in pci_init_board() seems to assume that every port has
three lanes. This is obviously wrong, and breaks support for Armada 38x.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ZYNQ || ARCH_ZYNQMP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The pinmuxing for i.MX53 FEC ethernet copied from
<kernel>/arch/arm/boot/dts/imx53-qsb-common.dtsi (at least until v4.9)
was bad. It is different from the manual pinmuxing in
<u-boot>/board/freescale/mx53loco/mx53loco.c which was used in
cx9020 implementation previously before mainlining into u-boot.
It seems the bug in imx53-qsb kernel device tree is hidden for so long,
because it was never used, by the kernel driver.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
It seems more readable to use arrays to get SoC specific parameters
instead of the crappy switch statement.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For LD20 SoC, the last 64 byte of each DRAM bank is used for the
dynamic training of DRAM PHY. The regions must be reserved in DT to
prevent the kernel from using them. Now gd->bd->bi_dram reflects
the actual memory banks. Just use it instead of getting access to
the board parameters.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
U-Boot needs to set up available memory area(s) in dram_init() and
dram_init_banksize(). It is platform-dependent how to detect the
memory banks. Currently, UniPhier adopts the memory banks _alleged_
by DT. This is based on the assumption that users bind a correct DT
in their build process.
Come to think of it, the DRAM controller has already been set up
before U-Boot is entered (because U-Boot runs on DRAM). So, the
DRAM controller setup register seems a more reliable source of any
information about DRAM stuff. The DRAM banks are initialized by
preliminary firmware (SPL, ARM Trusted Firmware BL2, or whatever),
so this means the source of the reliability is shifted from Device
Tree to such early-stage firmware. However, if the DRAM controller
is wrongly configured, the system will crash. If your system is
running, the DRAM setup register is very likely to provide the
correct DRAM mapping.
Decode the SG_MEMCONF register to get the available DRAM banks.
The dram_init() and dram_init_banksize() need similar decoding.
It would be nice if dram_init_banksize() could reuse the outcome
of dram_init(), but global variables are unavailable at this stage
because the .bss section is available only after the relocation.
As a result, SG_MEMCONF must be checked twice, but a new helper
uniphier_memconf_decode() will help to avoid code duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The two arrays ddrphy_{op,ip}_dq_shift_val, occupy more than 3.8 KB
memory footprint, which is significant in SPL.
There are PHY parameters for 5 boards, but they are actually not
board specific, but SoC specific. After all, we just need to have
2 patterns, for LD20 and LD21. Also, the shift values are small
enough to become "short" type instead of "int". This change will
save about 3 KB memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds glue code required for enabling the designware
mac on stm32f7 devices.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use the clock setup function defined in clock.c instead of setting the
clock bits directly in the drivers.
Remove register definitions of RCC in rcc.h as these are already
defined in the struct in stm32.h
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
The fmc base address is defined twice, once in fmc.h and once in stm32.h.
Fix wrong definition in stm32.h.
Remove the definiton in fmc.h.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
Cleanup stm32f7 files:
- use BIT macro
- use GENMASK macro
- use rcc struct instead of macro additions
Add missing stm32f7 register in rcc struct
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA<vikas.manocha@st.com>
This patch adds the DTS source files needed for stm32f746-disco board
The files are based on the stm32f429/469 files from current linux
kernel.
Source for "arch/arm/dts/armv7-m.dtsi": Linux: "arch/arm/boot/dts/armv7-m.dtsi"
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
The check for OMAP3630/3730 only checks for 800MHz 3630/3730, but
anything else is lumped into 36XX/37XX with an assumed 1GHz speed.
Based on the DM3730 TRM bit 9 shows the MPU Frequency (800MHz/1GHZ).
This also adds the ability to distinguish between the DM3730, DM3725,
AM3715, and AM3703 and correctly display their maximum speed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
This feature seems to be sometimes misunderstood. The intention is:
[1] Bring the slaves into the U-Boot proper image, not SPL (unless
you have a special reason to do otherwise).
[2] The operation must be done in a board (SoC) specific manner
since how to wake the slaves from the Boot ROM is SoC specific.
[3] The slaves must enter U-Boot proper after U-Boot relocates
itself because the "cpu-release-addr" property points to the
relocated memory area.
[2] is already explained in the help. We can make [1] even clearer
by mentioning "U-Boot proper" instead of "U-Boot". [3] is missing,
so I am adding it to the list. Instead, "before the master CPU
jumps to the kernel" is a matter of course, so removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
chiliBoard is a development board which uses chiliSOM as its base.
Hardware specification:
* chiliSOM (TI AM335x, DRAM, NAND)
* Ethernet PHY (id 0)
* USB host (usb1)
* MicroSD slot (mmc0)
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
chiliSOM is a System On Module (http://http://grinn-global.com/chilisom/).
It can't exists on its own, but will be used as part of other boards.
Hardware specification:
* TI AM335x processor
* 128M, 256M or 512M DDR3 memory
* up to 256M NAND
We place source inside arch/arm/mach-omap2/ directory and make it
possible to reuse initialization code (i.e. DDR, NAND init) for all
boards that use it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration file with parameters that are very likely to be shared by
all ast2500-based boards.
Add ast2500-board.c file with the init code that is very likely to be
shared by all ast2500-based boards.
Reviewed-by: Simon Glass <sjg@chromium.org>
Clock Driver
This driver is ast2500-specific and is not compatible with earlier
versions of this chip. The differences are not that big, but they are
in somewhat random places, so making it compatible with ast2400 is not
worth the effort at the moment.
SDRAM MC driver
The driver is very ast2500-specific and is completely incompatible
with previous versions of the chip.
The memory controller is very poorly documented by Aspeed in the
datasheet, with any mention of the whole range of registers missing. The
initialization procedure has been basically taken from Aspeed SDK, where
it is implemented in assembly. Here it is rewritten in C, with very limited
understanding of what exactly it is doing.
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Watchdog Timer, which is compatible with AST2400 and
AST2500 watchdogs. There is no uclass for Watchdog yet, so the driver
does not follow the driver model. It also uses fixed clock, so no clock
driver is needed.
Add support for timer for Aspeed ast2400/ast2500 devices.
The driver actually controls several devices, but because all devices
share the same Control Register, it is somewhat difficult to completely
decouple them. Since only one timer is needed at the moment, this should
be OK. The timer uses fixed clock, so does not rely on a clock driver.
Add sysreset driver, which uses watchdog timer to do resets and particular
watchdog device to use is hardcoded (0)
Reviewed-by: Simon Glass <sjg@chromium.org>
The LS1046A processor has three integrated USB 3.0 controllers
(USB1, USB2, and USB3) that allow direct connection to the USB
ports with appropriate protection circuitry and power supplies.
USB1 and USB2 ports are powered by a NX5P2190UK device, which
supplies 5v power at up to 1.2 A. The power enable and
power-fault-detect pins are connected to the LS1046A processor
via CPLD for individual port management.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moving arch/arm/mach-litesom/ to arch/arm/cpu/armv7/mx6/ was requested
in [1] during discussion of chiliSOM support patches.
[1] http://lists.denx.de/pipermail/u-boot/2017-January/279137.html
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Before commit 81c4eccb55 ("imx: mx6: fix USB bmode to use
reserved value") a non-reserved value has been used to trigger
Serial Downloader using bmode, which translated to a GPR9 value
of 0x10. However, on some boards the non-reserved value lead to
unreliable bmode command. With the above mentioned commit, U-boot
switched to use [7:4] b0001, which translates to GPR9 0x10 for
Serial Downloader mode. Check for the new value and classify it
as Serial Downloader mode.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
This patch adds the SDHCI device tree nodes to the Armada 7040-db
dts file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds the SDHCI device tree nodes to the Armada AP806 dtsi
file which is used by the Armada 7k/8K SoCs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds the SDHCI device tree nodes to the Armada 3700-db
dts file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds the SDHCI device tree nodes to the Armada 3700 dtsi
file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Currently all secure media types of SPL are generated for all platforms,
all platforms do not need all types, only generate the media types valid
for each platform.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
This option should not really be user selectable. Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
Introduce board/freescale/common/Kconfig so that we have a single place
for CONFIG options that are shared between ARM and PowerPC NXP platforms.
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Rename CONFIG_IMX31_PHYCORE_EET to CONFIG_TARGET_IMX31_PHYCORE_EET and
make this a distinct config target.
Signed-off-by: Tom Rini <trini@konsulko.com>
All the UniPhier DT files are compiled if CONFIG_ARCH_UNIPHIER
is enabled, but not all of them actually work. For example, when
U-Boot is compiled for ARM 32 bit, 64 bit DT files are also built,
and vice versa. Compile only the combination that makes sense.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There are similar functions that look up SoC data by the SoC ID.
The new macro UNIPHIER_DEFINE_SOCDATA_FUNC will be helpful to
avoid the code duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, uniphier_get_soc_type() converts the SoC ID (this is
read from the revision register) to an enum symbol to use it for SoC
identification. Come to think of it, there is no need for the
conversion in the first place. Using the SoC ID from the register
as-is a straightforward way.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The <common.h> includes too many headers. Actually, these files
needed to include it for udelay() declaration. Now we can replace
it with <linux/delay.h> thanks to commit 5bc516ed66 ("delay:
collect {m, n, u}delay declarations to include/linux/delay.h").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These files only need error number macros. Actually, IS_ERR(),
PTR_ERR(), ERR_PTR(), etc. are not useful for U-Boot. Avoid
unnecessary header includes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We may want to run different firmware before running U-Boot. For
example, ARM Trusted Firmware runs before U-Boot, making U-Boot
a non-secure world boot loader. In this case, the SoC might be
initialized there, which enables us to skip SPL entirely.
This commit removes "select SPL" to make it configurable. This
also enables the Multi SoC support for the UniPhier ARMv8 SoCs.
(CONFIG_ARCH_UNIPHIER_V8_MULTI) Thanks to the driver model and
Device Tree, the U-Boot proper part is now written in a generic way.
The board/SoC parameters reside in DT. The Multi SoC support
increases the memory footprint a bit, but the U-Boot proper does
not have strict memory constraint. This will mitigate the per-SoC
(sometimes per-board) defconfig burden.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The ddrphy_shift_rof_hws() never writes back the shifted delay value
to the register, which makes this function non-effective.
Signed-off-by: Kotaro Hayashi <hayashi.kotaro@socionext.com>
[masahiro: add git log]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Latest gcc compile strted complaining about defined structure definition
that are not used. Remove the unused sturctures.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Latest gcc 6.2 compiler is throwing the below warning for omap4_panda_defconfig
arch/arm/mach-omap2/omap4/hw_data.c:136:3: warning: 'abe_dpll_params_sysclk_196608khz' defined but not used [-Wunused-const-variable=]
abe_dpll_params_sysclk_196608khz[NUM_SYS_CLKS] = {
Fix this by guarding it with CONFIG_SYS_OMAP_ABE_SYSCK
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
We have long had available optimized versions of the memset and memcpy
functions that are borrowed from the Linux kernel. We should use these
in normal conditions as the speed wins in many workflows outweigh the
relatively minor size increase. However, we have a number of places
where we're simply too close to size limits in SPL and must be able to
make the size vs performance trade-off in those cases.
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
While moving OMAP related files to mach-omap2 the functionality
relating to generating secure boot files was modified. This change
prevents secure platforms other than AM33xx and OMAP54XX from
correctly building files for all needed media types.
Fixes: 983e37007d ("arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
commit: 65f83802b7 "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.
Since the above patch, you have to setup the fcr register.
For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...
This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.
Detected this issue with automated tbot tests on am335x
based shc board.
The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)
Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Moved the config FSL_PPA_ARMV8_PSCI from fsl-layerscape's Kconfig to
Kconfig under armv8 and renamed it to SEC_FIRMWARE_ARMV8_PSCI.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For 64-bit kernel, there is a warning about x1-x3 nonzero in violation
of boot protocol. To fix this issue, input argument 4 is added for
armv8_switch_to_el2 and armv8_switch_to_el1. The input argument 4 will
be set to the right value, such as zero.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The default MSI node in kernel tree is for LS1043A rev1.0 silicon, if
rev1.1 silicon used, need to fixup the MSI node to match it.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS1043A rev1.1 silicon supports two types of GIC offset: 4K
alignment and 64K alignment. The bit SCFG_GIC400_ALIGN[GIC_ADDR_BIT]
is used to choose which offset will be used.
The LS1043A rev1.0 silicon only supports the CIG offset with 4K
alignment.
If GIC_ADDR_BIT bit is set, 4K alignment is used, or else 64K alignment
is used. 64K alignment is the default setting.
Overriding the weak smp_kick_all_cpus, the new impletment is able to
detect GIC offset.
The default GIC offset in kernel device tree is using 4K alignment, it
need to be fixed if 64K alignment is detected.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
By default the SATA IP on the ls208Xa SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc register.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add the chip power supply voltage initialization on LS1046ARDB.
Add function power_init_board(), and it will initialize the
PMIC and call the chip power initialization function.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Set up chip power supply voltage according to voltage ID.
The fuse status register provides the values from on-chip
voltage ID fuses programmed at the factory. These values
define the voltage requirements for the chip.
Main operations:
1. Set up the core voltage
2. Set up the SERDES voltage and reset SERDES lanes
3. Enable/disable DDR controller support 0.9V if needed
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Without a prompt in Kconfig, SECURE_BOOT cannot be selected by
defconfig. The option was dropped unintentionally when defconfig
files were cleaned up. Three targets were impacted
ls1043ardb_SECURE_BOOT, ls2080ardb_SECURE_BOOT,
ls2080aqds_SECURE_BOOT.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update bootscript and its hdr addresses for Layerscape Chasis 3
based platforms instead of individual SoCs.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch binds the sys_info->freq_systembus to Platform PLL, and
implements the IPs' clock function individually.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Up to now, there are 3 kind of SoCs under Layerscape Chassis 2,
like LS1043A, LS1046A and LS1012A. But the clocks tree has a
lot of differences, for instance, the IP modules have different
dividers to derive its clock from Platform PLL. And the core
cluster PLL and platform PLL maybe have different reference
clocks, such as LS1012A. Another problem is which clock/PLL
should be described by sys_info->freq_systembus, it is confused
in Layerscape Chissis 2.
This patch is to bind the sys_info->freq_systembus to the Platform
PLL, and handle the different divider of IP modules separately
between different SoCs, and separate reference clocks of core
cluster PLL and platform PLL.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For A53, data coherency is enabled only when the CPUECTLR.SMPEN bit is
set. The SMPEN bit should be set before enabling the data cache.
If not enabled, the cache is not coherent with other cores and
data corruption could occur.
For A57/A72, SMPEN bit enables the processor to receive instruction
cache and TLB maintenance operations broadcast from other processors
in the cluster. This bit should be set before enabling the caches and
MMU, or performing any cache and TLB maintenance operations.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS1012A processor has two integrated USB controllers.
One is USB2.0 controller, the other is USB3.0 controller that
allow direct connection to the USB ports with appropriate
protection circuitry and power supplies.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Clear the content to zero and the ECC error bit of OCRAM1/2.
The OCRAM must be initialized to ZERO by the unit of 8-Byte before
accessing it, or else it will generate ECC error. And the IBR has
accessed the OCRAM before this initialization, so the ECC error
status bit should to be cleared.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The real size of OCRAM is 128KiB, so correct the size of OCRAM.
And OCRAM reserved 2MiB space, then add a new macro to describe
it, which is used for MMU setup.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch enables PCIe in ls2080a defconfigs and
removes unused PCIe related macro defines.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For the function alloc_stream_ids() append_mmu_masters() and
fdt_fixup_smmu_pcie() there are no related definitions and they
are never called. So the patch removes the unnecessary declares.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is recommended to set forced-order mode in RNI-6,
RNI-20 for performance optimization in LS2088A.
Both LS2080A, LS2088A families has CONFIG_LS2080A define.
As above update is required only for LS2088A, skip this
for LS2080A SoC family.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add the i2c_5 node and pmic as its child node.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
For Getting from uclass, use the "max8998-pmic" as name.
It also needs to change the dt-node's name as "max8998-pmic".
Otherwise, it doesn't find the pmic device.
Because it's only searching for 'max8998_pmic'.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Initialize SBC and Support Card in U-Boot proper instead of SPL.
We may run different firmware (ex. ARM Trusted Firmware) before
U-Boot, and basic SoC initialization may be done there. In that
case, SPL may not be used.
The motivation for preparing SBC and Support Card in SPL was to use
LED for early debugging, but this is not mandatory to boot SoCs.
With this commit, LED will be unavailable in SPL, but we can use a
debug serial instead. So, this change will not be a big deal.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Merge init-*.c into a single file using a table of callbacks because
the initialization flow is almost common among SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The code here is cluttered due to the switch statement. Introduce a
table of callbacks to clean up the initialization code across SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Splitting reset assertion (support_card_reset) and deassertion
(support_card_init) is not adding much value any more. Handle
all the initialization of Support Card in support_card_init(),
then remove support_card_reset().
Also, detect_num_flash_banks() can have a static qualifier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, memconf-sld3.c and memconf-pxs2.c duplicate the code.
There are 3 patterns in terms of MEMCONF init:
- DRAM 2 channels: LD4, sLD8, Pro4, Pro5, LD11
- DRAM 3 channels: sLD3
- DRAM 3 channels (Ch2 is disable by MEMCONF[21]): Pxs2, LD20
All of them can be moved into a single file by a little more
refactoring.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The clock enable bits for UMC are more SoC-specific than for
the other hardware blocks. Separate the UMC clocks and the other
clocks for better code reuse across SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At first, we thought the LD20 PLL setting would be board dependent,
but this argument turned out unneeded after all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The OrangePi Zero can happily use the EMAC along with its integrated
PHY to use Ethernet (for TFTP booting, for instance).
Add the emac node to the board .dts by copying it from the OrangePi One
DT.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add a proper device tree file for Orange Pi Zero boards from Xunlong,
which come with a Allwinner H2+ SoC (similar to H3).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The nanopi already had the CONFIG_SUN8I_EMAC=y enabled in it's defconfig
file, but was missing the &emac the device tree entry.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Right now the SPL is trying to load u-boot based on defines, i.e. one
has to define CONFIG_SPL_NAND_SIMPLE to boot from NAND,
or CONFIG_SPL_SPI_LOAD to boot from SPI FLASH, etc...
This prevent us from having a single SPL image that is able to boot from
all media, and one need to build an image for each medium. This
commit is replacing the #ifdef that select the boot medium by reading
the value of the boot pins (via the BOOTCFG register).
Now a single SPL image will be able to read from the boot pin to know
which device should be used to load u-boot.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Using CONFIG_IS_ENABLED() doesn't work in SPL. This patch replaces the only
occurrence of CONFIG_IS_ENABLED() in start.S to a regular #if defined().
It also adds "&& !defined(CONFIG_SPL_BUILD)" to that #if statement because
the spin-table code can't currently work in SPL, and the spin-table file
isn't even compiled in SPL.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
On AM33xx devices the secure ROM uses a different call index for
signature verification, the function and arguments are the same.
Signed-off-by: Andrew F. Davis <afd@ti.com>
This re-syncs the MACH_TYPE_xxx values from the Linux Kernel v4.9
release. In addition this removes all of the machine_arch_type and
machine_is_xxx logic that is unused in U-Boot. This removal removes a
large number of otherwise unused CONFIG values from the list to be
converted.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Adam Ford <aford173@gmail.com>
Isp-camera preview image will be broken when dual screen display mode.
This patch set isp/vop qos level higher to solve this problem.
We have verified this patch on rk3288-miniarm board.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
rk3399 has two clock-controller: cru and pmucru, update the
rockchip_get_crui() API, and rockchip_get_clk() do not used for
other module.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The popmetal board using a HOST_VBUS_DRV gpio signal to control the
USB host port 5V power, add a fix regulator and pinctrl for it, and
enable the USB host1 controller with the vbus-supply.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip: tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
With entry_point now being an unsigned long we need to adapt the last
two debug prints to use %lX not %X.
Fixes: 11e1479b9e ("SPL: make struct spl_image 64-bit safe")
Signed-off-by: Tom Rini <trini@konsulko.com>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'
[2] Commit the changes
[3] Create entries in driver/mmc/Kconfig.
(copied from Linux)
[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI
[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Xilinx ATF extending options for passing images from BL2(FSBL)
to BL31. U-Boot SPL is FSBL replacement that's why it should generate
handoff structure the same. Support only one entry which is U-Boot in
EL2 itself. When FIT image is adopted structure generate should be data
driven.
Currently ATF is placing this structure at the beggining of OCM which is
rewriting early parts of ATF which should be unused at that time.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a string description for SYS_VENDOR to allow configuring boards from
other vendors than just "xilinx".
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core
which fixes some silicon bugs that needed software workarounds
in Version 1.0 that was used on Zynq systems.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable and use the clock driver routine
defined in clock driver toset required
clock appropriately.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added the idle-states node to describe zynqmp idle states. Only cpu-sleep-0
idle state is added in this patch. References to the idle-states node are
added in all CPU nodes. Time values: entry/exit latencies and min-residency,
needs to be tuned. arm,psci-suspend-param is selected to comply with PSCIv1.0
and Extended StateID format.
Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Just sync between version. Others zynqmp boards have this setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The watchdog clock node is missing.
Add the same. This solves the below error.
cdns-wdt fd4d0000.watchdog: input clock not found
cdns-wdt: probe of fd4d0000.watchdog failed with error -2
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
spi-max-frequency for spi bus depends on devices which are
connected to it. Remove this parameter from dtsi file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add usb ether gadget device with usb_ether_init() when
CONFIG_DM_ETH and CONFIG_USB_ETHER are defined.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL load address changes based on boot type in HS devices,
ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs
for similar reasons. Add this same logic for AM33xx devices.
Also make the default value for ISW_ENTRY_ADDR correct for GP
devices based on SoC, HS devices already pick the correct
value in their defconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
When TI_SECURE_DEV_PKG is not defined we warn that the file '*_HS' was
not generated but generate an unsigned one anyway, first fix this
warning to say that it was generated but not secured.
When the user then exports TI_SECURE_DEV_PKG after getting this warning,
and tries to re-build, 'make' will detect the build artifacts as
unchanged and so assume they do not need to be re-generated. This causes
it to fail to sign the files and it will pack unsigned files into the
final image, even though TI_SECURE_DEV_PKG is now correctly defined and
working.
Fix this by using FORCE on the targets causes them to be re-run even if
the dependent files have not changed.
This then causes another issue. We currently rename the signed dtb files
to overwrite the non-signed ones. We do this so the 'mkimage' tool gives
the packaged dtb sections the correct name. If we do not rename the files
then SPL will not find them during boot.
Fix this by renaming the dtb files by appending _HS to the end of the
filename, after the ".dtb", this causes them to still be named correctly
in the FIT blob.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
Signed-off-by: York Sun <york.sun@nxp.com>
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <trini@konsulko.com>
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <york.sun@nxp.com>
Now that the SPL is ready to be compiled in AArch64 and the DRAM
init code is ready, enable SPL support for the A64 SoC and in the
Pine64 defconfig.
For now we keep the boot0 header in the U-Boot proper, as this allows
to still use boot0 as an SPL replacement without hurting the SPL use
case.
We disable FEL support for now by making its compilation conditional
and disabling it for ARM64, as the code isn't ready yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Fix the output of the DRAM size on AArch64 SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
According to Jens disabling the on-die-termination should set bit 5,
not bit 1 in the respective register. Fix this.
Reported-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The A64 DRAM controller is very similar to the H3 one,
so the code can be reused with some small changes.
This refactoring does not change the code size for the existing H3 part.
[Andre: rework from #ifdefs to using socid parameters in static
functions, minor fixes, merging in fixes from Jens]
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
So far the DRAM driver for the H3 SoC (and apparently boot0/libdram as
well) only applied coarse delay line settings, with one delay value for
all the data lines in each byte lane and one value for the control lines.
Instead of setting the delays for whole bytes only allow setting it for
each individual bit. Also add support for address/command lane delays.
For the purpose of this patch the rules for the existing coarse settings
were just applied to the new scheme, so the actual register writes don't
change for the H3. Other SoCs will utilize this feature later properly.
With a stock GCC 5.3.0 this increases the dram_sun8i_h3.o code size from
2296 to 2344 Bytes.
[Andre: move delay parameters into macros to ease later sharing, use
defines for numbers of delay registers, extend commit message]
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The IOCR registers got renamed to BDLR to match the public
documentation of similar controllers.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
So far the MBUS priority setup was done by writing "magic" values taken
from a DRAM controller register dump after a boot0 run.
By peeking at the Linux (sic!) MBUS driver [1] from the Allwinner BSP
kernel, we learned more about the actual meaning of those bits.
Add macros and refactor the setup function to make the MBUS setup much
more readable and meaningful.
The actual values used now are a transformation of the values used
before, which are assembled by the new code to result in the same register
writes. So this rework does not change any settings, also the code size
stays the same.
The respective source files in the BSP kernel had a proper GPL header,
so lifting this code and information into U-Boot is legal.
[Andre: provide a convenience macro to fit definitions on one line]
[1] https://github.com/longsleep/linux-pine64/blob/lichee-dev-v3.10.65/drivers/bus/sunxi_mbus.c
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner A64 SoC starts execution in AArch32 mode, and both
the boot ROM and Allwinner's boot0 keep running in this mode.
So U-Boot gets entered in 32-bit, although we want it to run in AArch64.
By using a "magic" instruction, which happens to be an almost-NOP in
AArch64 and a branch in AArch32, we differentiate between being
entered in 64-bit or 32-bit mode.
If in 64-bit mode, we proceed with the branch to reset, but in 32-bit
mode we trigger an RMR write to bring the core into AArch64/EL3 and
re-enter U-Boot at CONFIG_SYS_TEXT_BASE.
This allows a 64-bit U-Boot to be both entered in 32 and 64-bit mode,
so we can use the same start code for the SPL and the U-Boot proper.
We use the existing custom header (boot0.h) functionality, but restrict
the existing boot0 header reservation to the non-SPL build now. A SPL
wouldn't need such header anyway. This allows to have both options
defined and lets us use one for the SPL and the other for U-Boot proper.
Also add arch/arm/mach-sunxi/rmr_switch.S, which contains the original
ARM assembly code and instructions how to re-generate the encoded
version.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For prepending some board specific header area to U-Boot images we
were so far including a header file with a macro definition containing
the actual header specification.
This works fine if there are just a few statements and if there is only
one alternative.
However adding more complex code quickly gets messy with this approach,
so let's just drop that intermediate macro and let the #include actually
insert the code directly.
This converts the callers and the callees, but doesn't change anything
at this point.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The boot0 hook we have so far is applied _after_ the initial branch
to the "reset" entry point. An upcoming change requires even this
branch to be changed, so we apply the hook macro at the earliest
point, and have the branch in the hook file as well.
This is no functional change at this point, just refactoring to simplify
upcoming patches.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunxi DRAM setup code needs an sdelay() implementation, which
wasn't defined for armv8 so far.
Shamelessly copy the armv7 version and adjust it to work in AArch64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Since entry_point and load_addr are addresses, they should be
represented as longs to cover the whole address space and to avoid
warning when compiling the SPL in 64-bit.
Also adjust debug prints to add the 'l' specifier, where needed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The UL() macro is pretty useful in sharing constants between assembly
and C files while still being able to specify a type for C.
Move the macro from an armv8 specific header into a common header file
to be able to use it by arm code (for instance) as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For boards that call s_init() when the SPL runs, we are expected to
setup an early stack before calling this C function.
Implement the proper AArch64 version of this based on the ARMv7 code.
This allows sunxi boards to setup the basic peripherals even with a
64-bit SPL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The predominantely 32-bit ARM targets try to compile the SPL in Thumb
mode to reduce code size.
The 64-bit AArch64 instruction set does not know an alternative, concise
encoding, so the Thumb build option should only be set for 32-bit
targets.
Likewise -marm machine options are only valid for ARMv7 targets.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
These days many Allwinner SoCs use clock_sun6i.c, although out of them
only the (original sun6i) A31 has a second MBUS clock register.
Also the requirement for setting up the PRCM PLL_CTLR1 register to provide
the proper voltage seems to be a property of older SoCs only as well.
Restrict the MBUS initialization to this SoC only to avoid writing bogus
values to (undefined) registers in other chips.
I can only verify that the PLL voltage setup is not needed for H3 and
A64, so for now we only spare those two SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Sync with Linux 4.8 dts plus vdd_bl regulator
to fix backlight start, display timings and USB
controller aliases fix.
Signed-off-by: Misha Komarovskiy <zombah@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix ULPI reset polarity which caused a hard hang on Colibri T20 upon
attempting to start the USB subsystem:
This fixes my late commit d5a24d8b53
(colibri_t20: fix usb operation and controller order) inadvertently
having overwritten Stephen's previous commit
2f6a7e8ce5 (ARM: tegra: fix USB ULPI PHY
reset signal inversion confusion).
While at it also fix comment about on-module USB port.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a comment about the disabled PCIe port nodes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some users may wish to pass the cboot-supplied DTB to the booted kernel
rather than having U-Boot load the DTB itself. To allow this, expose the
address of the cboot-supplied DTB in environment variable $fdt_addr. At
least when using extlinux.conf, if the user doesn't explicitly specify
which DTB to pass to the kernel, U-Boot passes the DTB referred to by
this variable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Features supported :
* Serial console
* SPI Flash
* MMC/SD Card
* eMMC storage
* SATA
* PCA9555 - GPIO expander over I2C5 bus
* USB
Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: Adjust to v2016.11]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
To being able to sign created binaries, we need to know the HAB Blocks
for that image. Especially for the imximage type the HAB Blocks are
only available during creation of the image. We want to preserve the
information until we get to sign the files.
In the verbose case we still get them printed out instead of writing
to log files.
Cc: sbabic@denx.de
v2-Changes:
- No usage of MKIMAGEOUTPUT_$(@F) macro.
- Predefine default value /dev/null in every involved Makefile.
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
When using HAB as secure boot mechanism on Wandboard, the chain of
trust breaks immediately after the SPL. As this is not checking
the authenticity of the loaded image before jumping to it.
The HAB status output will not be implemented in SPL as it adds
a lot of strings that are only required in debug cases. With those
it exceeds the maximum size of the available OCRAM (69 KiB).
The SPL MISC driver support must be enabled, so that the driver can use OTP fuse
to check if HAB is enabled.
Cc: sbabic@denx.de
v2-Changes: None
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
These files are blowing up the SPL and should not be required
there as the SPL delivers no command console. Because building fails
for mx27 and mx31 machines with SPL build, we remove the linker flag
for them from the Makefile. Nothing is built for them to be linked
in that directory.
Cc: sbabic@denx.de
v2 Changes:
- Remove mx27 and mx31 from Makefile during SPL build as nothing is built for
them in that directory. And removing the commands with the libs-y directive
lead to linker failures. e.g. "armv5te-ld.bfd: cannot find arch/arm/imx-common/built-in.o: No such file or directory)"
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
While I moved the options, I also renamed them so that they are all
prefixed with MMC_SDHCI_.
This commit was created in the following steps.
[1] Rename with the following command
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g
s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g
s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g
s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g
s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g
s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g
'
[2] create the Kconfig entries in drivers/mmc/Kconfig
[3] Move the options by the following command
tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \
MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR
[4] Sort drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
I am not longer using my old email address
"ajay.bhargav@einfochips.com". For U-Boot development email address is
now updated to contact@8051projects.net
Signed-off-by: Ajay Bhargav <contact@8051projects.net>
Commit be72591bcd ("Kconfig: Move USE_ARCH_MEMCPY/MEMSET to
Kconfig") is misconversion.
The original logic in include/configs/uniphier.h was as follows:
#if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_ARM64)
#define CONFIG_USE_ARCH_MEMSET
#define CONFIG_USE_ARCH_MEMCPY
#endif
This means those configs were enabled when building U-Boot proper,
but disabled when building SPL. Likewise for Tegra.
Now "depends on !SPL" prevents any boards with SPL support
from reaching these options. This changed the behavior for
UniPhier and Tegra SoC family.
Please notice these two options only control the U-Boot proper
build. As you see arch/arm/Makefile, ARM-specific memset/memcpy
are never compiled for SPL. So, __HAVE_ARCH_MEMCPY/MEMSET should
not set for SPL.
Fixes: be72591bcd ("Kconfig: Move USE_ARCH_MEMCPY/MEMSET to Kconfig")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
To use driver-model adds the pmic node for max8998.
This is used as kerel device-tree in Linux.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Fix the MMU mapping for A8K device family:
- Separate A7K and A8K memory mappings
- Fix memory regions by including IO mapping for all
3 PCIe interfaces existing on each connected CP110 controller
Add A8K memory mapping documentation with all regions
configured by Marvell ATF.
Change-Id: I9c930569b1853900f5fba2d5db319b092cc7a2a6
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
H3 SID controller has some bug, which makes the initial SID value at
SUNXI_SID_BASE wrong when boot.
Change the SID retrieve code to call the SID Controller directly on H3,
which can get the correct value, and also fix the SID value at
SUNXI_SID_BASE, so that it can be used by further operations.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch also includes ARM64 zynqmp changes:
- Remove platform non DM initialization
- Remove hardcoded sata base address
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By adding labels to the cpu nodes in the dtsi, a dts that
includes it can change the OPPs by referencing the cpu0
through the label.
[Based on linux (400b6a0cbef55d1ae32808eaa1ef1c28820bf6ac)]
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move sunxi boards to use binman. This involves adding the image definition
to the device tree and using it in the Makefile.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
With the new device-tree rules it is possible to put device-tree changes
needed by U-Boot into their own file. As an example of this approach, move
Tegra over to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Shuffle the macros around a little to remove the following warning
when building for i.MX28:
arch/arm/cpu/arm926ejs/mxs/spl_boot.c:44:26: warning: ‘iomux_boot’ defined but not used [-Wunused-const-variable=]
static const iomux_cfg_t iomux_boot[] = {
^~~~~~~~~~
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX6UL dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Use CONFIG_DM_ETH and remove board_eth_init code
from board files.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Move USE_ARCH_MEMCPY/MEMSET options to Kconfig.
Make it "default y" for the ARMv7 architecture and make it
depend on !ARM64 && !SPL.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
The LCDIF Pixel clock mux is not glitchless, so need
to gate before changing mux.
Also change enable_lcdif_clock prototype with a new input
parameter to indicate disable or enable.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The mux for the lcd clock is not glitchless,
so need to first gate the clock before changing the mux.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
>From RM, per_periph2_clk_sel option3 is:
"derive clock from 198MHz clock (divided 392MHz PLL2 PFD)."
So fix it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX6SLL cpu type.
MXC_CPU_MX6D is not a real value in chip, so change it to 0x6A.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
liteBoard is a development board which uses liteSOM as its base.
Hardware specification:
* liteSOM (i.MX6UL, DRAM, eMMC)
* Ethernet PHY (id 0)
* USB host (usb_otg1)
* MicroSD slot (uSDHC1)
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
liteSOM is a System On Module (http://grinn-global.com/litesom/). It
can't exists on its own, but will be used as part of other boards.
Hardware specification:
* NXP i.MX6UL processor
* 256M or 512M DDR3 memory
* optional eMMC (uSDHC2)
Here we treat SOM similar to SOC, so we place it inside arch/arm/mach-*
directory and make it possible to reuse initialization code (i.e. DDR,
eMMC init) for all boards that use it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
It's not necessary to define the processor in the defconfig file.
The preferred method to select the SoC is via Kconfig file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This adds board support for the Toradex module family Colibri iMX6.
The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both
with a version for commercial and industrial temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
This adds board support for the Toradex module family Apalis iMX6.
The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with
commercial and industrial temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Add proper reg values for the two AIPS bus nodes. This avoids this
two warnings:
Node /soc/aips-bus@40000000 has a unit name, but no reg property
Node /soc/aips-bus@40080000 has a unit name, but no reg property
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
A most basic PSCI implementation with only one psci_version is added for
LS1043A, this can verify the generic PSCI framework, and more platform specific
implementation will be added later.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Newly add ARMv8 PSCI needs to be initialized, be copied or reserved in right
place, this patch does all the setup steps.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch introduces a generic ARMv8 PSCI framework, with all functions
returning a dummy ARM_PSCI_RET_NI (Not Implemented), then it is up to each
platform to implement their own functions based on this framework.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PSCI implementation needs the SMC instruction to be enabled.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds secure_text, secure_data and secure_stack sections for ARMv8 to
hold PSCI text and data, and it is based on the legacy implementation of ARMv7.
ARMV8_SECURE_BASE defines the address for PSCI secure sections, ARMV8_PSCI and
ARMV8_PSCI_NR_CPUS are firstly used in this patch, so they are introduce here
in Kconfig too.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP/Freescale uses macro CONFIG_ARMV8_PSCI to enable their private PSCI
implementation in PPA firmware, but this macro naming too generic, so this
patch replaces it with a specic one CONFIG_FSL_PPA_ARMV8_PSCI.
And this macro CONFIG_ARMV8_PSCI will be used for a generic PSCI for ARMv8
which will be added in following patchs.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The unit-address should be the same as the I2C address of the device.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Unlike Linux kernel, U-Boot depends on "spi-flash" compatible to probe
m25p80 spi-nor devices. Hence, add "spi-flash" compatible string to
m25p80 node. Without this patch, flash device DT data is not parsed and
QSPI operates in unsupported mode leading to data corruption.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add missing L3 cache flush functionality which absence prevents
Linux kernel from normal boot in case the L3 cache is enabled
by ATF.
The L3 cache is named the "last level" cache in order to keep
the terminology similar to the ATF code.
This cache should not be disabled by u-boot since the Linux
kernel cannot activate it, so it is activates at ATF stage.
However the cache flush is required for preventing data corruption
after disabling the MMU and the data cache before passing control
to the loaded Linux image.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add pin control nodes to APN806, CP-master, CP-slave and
Armada-7040 and Armada-8040 boards DTS files
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add a DM port of Marvell pin control driver.
The A8K SoC family contains several silicone dies interconnected
in a single package. Every die is normally equipped with its own
pin controller unit.
There are 2 pin controllers in A70x0 SoC and 3 in A80x0 SoC.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Align the Armada-8040-db and Armada-7040-db SPI and I2C
DTS settings with latest DB settings:
- 8040-db: disable i2c0 and spi0 on AP (MPPs are reserved for SDIO)
- 8040-db: disable cps_i2c0 on CP1
- 8040-db: enable spi1 on CP1 (the new location of the boot flash)
The spi1 on CP1 is aliased as spi0 since this is the way
the driver enumerates it.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This is a user configurable option, but "select BLK" forces users to
enable it.
Even with this commit, BLK is still enabled by "default y if DM_MMC"
for UniPhier SoCs; the difference is users can disable it if they
do not need it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x-evm. With
the default values LCDC suffers from DMA FIFO underflows and frame
synchronization lost errors. The initialization values are the highest
that work flawlessly when heavy memory load is generated by CPU. 32bpp
colors were used in the test. On BBB the video mode used 110MHz pixel
clock. The mode supported by the panel of am335x-evm uses 30MHz pixel
clock.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is useful to name each method so that we can print out this name when
using the method. Currently this happens using a separate function. In
preparation for unifying this, add a name to each method.
The name is only available if we have libcommon support (i.e can use
printf()).
Signed-off-by: Simon Glass <sjg@chromium.org>
solve issue when bootstage is used with armV7 generic timer
first call of timer_get_boot_us() use the function get_timer()
before timer initialization (arch.timer_rate_hz = 0)
=> div by 0
Commit-notes
When I activate bootstage on ARMV7 architecture with platform
using the generic armv7 timer defined in file
./arch/arm/cpu/armv7m/timer.c
I have a issue because gd->arch.timer_rate_hz = 0
For me the get_timer() function should not used before timer_init
(which initialize gd->arch.timer_rate_hz) at least for the ARMV7
timer.
But in the init sequence, the first bootstage fucntion is called
before timer_init and this function use the timer function.
For me it is a error in the generic init sequence :
mark_bootstage is called before timer_init.
static init_fnc_t init_sequence_f[] = {
....
arch_cpu_init_dm,
mark_bootstage, /* need timer, go after init dm */
...
#if defined(CONFIG_ARM) || defined(CONFIG_MIPS) || \
defined(CONFIG_BLACKFIN) || defined(CONFIG_NDS32) || \
defined(CONFIG_SPARC)
timer_init, /* initialize timer */
#endif
.......
To solve the issue for all the paltform, we can move timer_init()
call just before mark_bootstage() in this array...
It should be ok for ARMV7 but I don't sure for other platform
impacted
- the other ARM platform or ARMV7 wich don't use generic timer
- MIPS BLACKFIN NDS32 or SPARC
and I don't sure of impact for other function called
(board_early_init_f for example....)
=> This patch solve issue only in timer armv7
get_boot_us() can be called everytime without div by 0 issue
(gd->arch.timer_rate_hz is not used)
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Some Altera Quartus generated files have long lines that are split with a '\' at
the end of the line. It also wOn Windows, rites files in DOS format, which can
confuse some of the processing scripts in this file. This patch solves both issues.
Signed-off-by: Bill Randle <bill.randle@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Valid Altera SoCFPGA preloader image must contain special data at
offsets 0x40, 0x44, 0x48 and valid instructions at address 0x4c or
0x50. These addresses are by default used by U-Boot's vector table
and a piece of reset handler, thus a valid preloader corrupts those
addresses slightly. While this works most of the time, this can and
does prevent the board from rebooting sometimes and triggering this
issue may even depend on compiler.
The problem is that when SoCFPGA performs warm reset, it checks the
addresses 0x40..0x4b in SRAM for a valid preloader signature and
header checksum. If those are found, it jumps to address 0x4c or
0x50 (this is unclear). These addresses are populated by the first
few instructions of arch/arm/cpu/armv7/start.S:
ffff0040 <data_abort>:
ffff0040: ebfffffe bl ffff0040 <data_abort>
ffff0044 <reset>:
ffff0044: ea000012 b ffff0094 <save_boot_params>
ffff0048 <save_boot_params_ret>:
ffff0048: e10f0000 mrs r0, CPSR
ffff004c: e200101f and r1, r0, #31
ffff0050: e331001a teq r1, #26
Without this patch, the CPU will enter the code at 0xffff004c or
0xffff0050 , at which point the value of r0 and r1 registers is
undefined. Moreover, jumping directly to the preloader entry point
at address 0xffff0000 will also fail, because address 0xffff004.
is invalid and contains the preloader magic.
Add BOOT0 hook which reserves the area at offset 0x40..0x5f and
populates offset 0x50 with jump to the entry point. This way, the
preloader signature is stored in reserved space and can not corrupt
the SPL code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Stefan Roese <sr@denx.de>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add CycloneV based Terasic DE1-SoC board. The board boots
from SD/MMC. Ethernet and USB host is supported.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marex@denx.de>
The default configuration for QSPI AHB bus can't support 16MB+.
But some flash on NXP layerscape board are more than 16MB.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add the name for register space and memory space.
<0x1550000 0x10000 > is the QSPI register space.
<0x40000000 0x4000000> is the QSPI memory space.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>
Not all memory is mapped in the MMU. So we need to restrict the memory
size so that U-Boot does not try to access it. Also, the internal
registers are located at 0xf000.0000 - 0xffff.ffff. Currently only 2GiB
are mapped for system memory. This is what we pass to the U-Boot
subsystem here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
To use the PCIe driver, its controller memory and the PCIe regions need
to get mapped in the MMU. Otherwise these areas can't be accessed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
The Armada8k implements 2 CPs (communication processors) and the 2nd
CP also is equipped with a COMPHY controller. This patch now loops
over all enabled MISC devices (CP110) enabled in the DT to initialize
all CPs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Add I2C and SPI aliases to enable usage in U-Boot. Otherwise U-Boot will
not be able to use the SPI NOR chip for environment storage and use
"i2c dev 0" to select this I2C bus.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds the COMPHY device tree configuration to the DT file for
the Marvell DB-88F8040 devel board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds the COMPHY and UTMI device tree nodes to the cp110-slave
dtsi file for the Armada 8K.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Since the cp110 slave also has comphy DT nodes, the names need to be
renamed to avoid a name clash. Lets use the common naming scheme:
"cpm_xxx" for master and "cps_xxx" for slave.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds the necessary files to support the Marvell Armada 8k
devel board. Most board specfic files are shared with the Armada 7k
boards under the name "armada-8k*". So only minimal changes are
necessary to add this basic board support (except the DT files of
course).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
To enable access to the slave CP its memory needs to be added to the
MMU memory map.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Add the latest version of the DT files from the Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This moves some of the Armada DB-88F7040 board specific files to a more
generic name: armada-8k. This is in preparation for the Armada-8k
support which will be added soon. And since both platforms share
most devices, lets also share most source files to not duplicate
the code here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
These are the last two samsung boards that don't use DM_I2C. Move them
over, leaving #ifdefs to allow the maintainer to complete this work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Three boards are still not converting to use DM_I2C. They are also using
the old PMIC framework. Rather than removing them, add #ifdefs to allow
them to continue to build. This will give the maintainers a little more
time to decide whether to convert them or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Commit 54e4fcfa3c ("ARM: mx6: add MMC2 boot device detection
support in SPL") prevents UDOO neo board to boot:
Trying to boot from MMC2
port 1
MMC Device 1 not found
spl: could not find mmc device. error: -19
SPL: failed to boot from all boot devices
This reverts commit 54e4fcfa3c.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 that were autogenerated on
19th October, 2016 by "Ahmad Rashed<a-rashed@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add DT support for dra71-evm and built it as part of FIT image.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Palmas driver assumes it is always TPS659xx regulator on all DRA7xx based
boards to enable mmc regulator. This is not true always like in case of
DRA71x-evm. So get this information based on the board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Delete omap4_vmmc_pbias_config from omap_hsmmc.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the pmic_data for LP873x PMIC which is used to power
up dra71x-evm.
Note: As per the DM[1] DRA71x supports only OP_NOM. So, updating
the efuse registers only to use OPP_NOM irrespective of any
CONFIG_DRA7_<VOLT>_OPP_{NOM,od,high} is defined.
[1] http://www.ti.com/product/DRA718/technicaldocuments
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds support to update the device-tree blob to adjust the
DSP and IVA DPLL clocks pertinent to the selected OPP choice, with
the default being OPP_NOM. The voltage settings are done in u-boot,
but the actual clock configuration itself is done in kernel because
of the following reasons:
1. SoC definition constraints us to NOT to do dynamic voltage
scaling ever after the initial avs0 setting in bootloader
- so the voltage must be set in bootloader.
2. The voltage level must be set even if the IP blocks like
GPU/DSP are unused.
3. The IVA, GPU and DSP DPLLs are not essential for u-boot functionality,
and similar DPLL clock configuration code has been cleaned up in
v2014.10 u-boot release. See commit, 02c41535b6 ("ARM: OMAP4/5:
Remove dead code against CONFIG_SYS_CLOCKS_ENABLE_ALL").
The non-essential DPLLs are configured within the kernel during
the clock init step when parsing the device tree and creating
the clock devices. This approach meets both the u-boot and kernel
needs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Subhajit Paul <subhajit_paul@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Redefine the macros used to define the voltage values and the
efuse register offsets based on OPP for all the voltage domains.
This is done using Kconfig macros that can be set in a defconfig
or selected during a config step. This allows a voltage domain
to be configured/set to a corresponding voltage value depending
on the OPP selection choice.
The Kconfig choices have been added for MPU, DSPEVE, IVA and GPU
voltage domains, with the MPU domain restricted to OPP_NOM. The
OPP_OD and OPP_HIGH options will be added when the support for
configuring the MPU clock frequency is added. The clock
configuration for other voltage domains is out of scope in
u-boot code.
The CORE voltage domain does not have separate voltage values
and efuse register offset at different OPPs, while the MPU
voltage domain only has different efuse register offsets for
different OPPs, but uses the same voltage value. Any different
choices of OPPs for voltage domains on common ganged-rails
is automatically taken care to select the corresponding
highest OPP voltage value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It can be expected that different paper spins of a SoC can have
different definitions for OPP and can have their own constraints
on the boot up OPP for each voltage rail. In order to have this
flexibility, add support for dynamically selecting the OPP voltage
based on the board to handle any such exceptions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add an OPTEE node to the FDT when TEE installation has completed
successfully. This informs the kernel of the presence of OPTEE.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
secure_tee_install is used to install and initialize a secure TEE OS such as
Linaro OP-TEE into the secure world. This function takes in the address
where the signed TEE image is loaded as an argument. The signed TEE image
consists of a header (struct tee_header), TEE code+data followed by the
signature generated using image signing tool from TI security development
package (SECDEV). Refer to README.ti-secure for more information.
This function uses 2 new secure APIs.
1. PPA_SERV_HAL_TEE_LOAD_MASTER - Must be called on CPU Core 0. Protected
memory for TEE must be reserved before calling this function. This API
needs arguments filled into struct ppa_tee_load_info. The TEE image is
authenticated and if there are no errors, the control passes to the TEE
entry point.
2. PPA_SERV_HAL_TEE_LOAD_SLAVE - Called on other CPU cores only after
a TEE_LOAD_MASTER call. Takes no arguments. Checks if TEE was
successfully loaded (on core 0) and transfers control to the same TEE
entry point.
The code at TEE entry point is expected perform OS initialization steps
and return back to non-secure world (U-Boot).
Signed-off-by: Harinarayan Bhatta <harinarayan@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On DRA7xx platform, CPU Core 1 is not used in u-boot. However, in some
cases it is need to make secure API calls from Core 1. This patch adds
an assembly function to make a secure (SMC) call from CPU Core #1.
Signed-off-by: Harinarayan Bhatta <harinarayan@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL is unable to load u-boot because the DDR2 is not configured.
Configure the DDR2.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL is not able to boot properly because the PLL0 is not
configured. Configure it.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Clean config headers by moving CONFIG_SYS_DA850_DDR_INIT away to a
Kconfig file.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Clean config headers by moving CONFIG_SYS_DA850_PLL_INIT away to a
Kconfig file.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting in the way to maintain common code for DRA7x family.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For ECC enabled DDR, we use EDMA to reset all memory values to 0. For
K2E/L/H/K the priv ID of 8 was indicative of ARM, but that is not the
case for K2G, where it is 1.
Unfortunately, ddr3 code had hard coded the privID and had missed
identification previously. Fix the same, else unforeseen behavior can
be expected in our reset of DDR contents to 0 for ECC enablement.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently all backend driver ops uses hard coded physical
address, so to adopt the driver to DM, add device pointer to ops
call backs so that drivers can get physical addresses from the
usb driver priv/plat data.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MUSB wrapper driver is bound as MISC device and underlying usb
devices are bind to usb drivers based on dr_mode, so probing the
MISC wrapper driver to register musb devices.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Do not register usb devices when CONFIG_DM_USB is define.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit e2f88dfd2d ("libfdt: Introduce new ARCH_FIXUP_FDT option")
allows us to skip memory setup of DTB, but a problem for ARM is that
spin_table_update_dt() and psci_update_dt() are skipped as well if
CONFIG_ARCH_FIXUP_FDT is disabled.
This commit allows us to skip only fdt_fixup_memory_banks() instead
of the whole of arch_fixup_fdt(). It will be useful when we want to
use a memory node from a kernel DTB as is, but need some fixups for
Spin-Table/PSCI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed build error for x86:
Signed-off-by: Simon Glass <sjg@chromium.org>
Now all mpc85xx and mpc86xx have converted to use SYS_CCSRBAR_DEFAULT
in Kconfig. Drop this macro for LSCH2 and remove from white list.
Signed-off-by: York Sun <york.sun@nxp.com>
Using alternative bootmode field to support automatic secondary boot
modes. It is purely software setting where SW modes are using free
bootmode combinations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP provides an option to overwrite bootmode setting which
can change SPL behavior.
For example: boot SPL via JTAG and then SPL loads images from SD.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The main PLL frequency is 2GHz for Armada-XP and 1GHZ for Armada 375,
38x and 39x.
[ Linux commit ae142bd9976532aa5232ab0b00e621690d8bfe6a ]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch extends the imx6 clock code to enable or disable the EIM
slow clock, which in necessary when one wants to use EIM interface t
o read/write from external memory (e.g. NOR).
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
This patch adds initial support for Samtec VIN|ING 2000 board.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
UDOO Neo Board is a development board from Seco that has three models:
- UDOO Neo Basic
- UDOO Neo Basic Kick Starter
- UDOO Neo Extended
- UDOO Neo Full
All versions are based on the i.MX6 SoloX processor.
For more details about the UDOO Neo board, please refer to:
http://www.udoo.org/udoo-neo/
This work is based on a previous commit of Francesco Montefoschi
<francesco.monte@gmail.com>:
877b71184a
Only tested on the UDOO Neo Full board.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The DDR calibration routines are gated by conditionals for the
i.MX6DQ SOCs, but with the use of the sysinfo parameter, these
are usable on at least i.MX6SDL and i.MX6SL variants with DDR3.
Also, since only the Novena board currently uses the dynamic
DDR calibration routines, these routines waste space on other
boards using SPL.
Add a KConfig entry to allow boards to selectively include the
DDR calibration routines.
Signed-off-by: Eric Nelson <eric@nelint.com>
Add routine mmdc_read_calibration() to return the output of DDR
calibration. This can be used for debugging or to aid in construction
of static memory configuration.
This routine will be used in a subsequent patch set adding a virtual
"mx6memcal" board, but could also be useful when gathering statistics
during an initial production run.
Signed-off-by: Eric Nelson <eric@nelint.com>
The DDR calibration routines have scattered support for bus
widths other than 64-bits:
-- The mmdc_do_write_level_calibration() routine assumes the
presence of PHY1, and
-- The mmdc_do_dqs_calibration() routine tries to determine
whether one or two DDR PHYs are active by reading MDCTL.
Since a caller of these routines must have a valid struct mx6_ddr_sysinfo
for use in calling mx6_dram_cfg(), and the bus width is available in the
"dsize" field, use this structure to inform the calibration routines which
PHYs are active.
This allows the use of the DDR calibration routines on CPU variants
like i.MX6SL that only have a single MMDC port.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The DDR calibration code is only setting flag DG_CMP_CYC (DQS gating sample
cycle) for the first PHY.
Set the 32-cycle flag for both PHYs and clear when done so the MPDGCTRL0
output value isn't polluted with calibration artifacts.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add constants for the MPZQLP2CTL DDR register for both
banks to allow setting the LPDDR2 timing values in
.cfg files using a named constant instead of hex addresses
as is currently done in mx6slevk and other board files.
Signed-off-by: Eric Nelson <eric@nelint.com>
The ipu has two display interfaces. Make the used one a parameter
in struct display_info_t instead of using unconditionally DI0.
DI0 is the default setting.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Check BOOT_CFG2[3:4] to determine which SD/MMC port is selected to boot
from. If MMC2 is selected return BOOT_DEVICE_MMC2. In all other cases
return BOOT_DEVICE_MMC1, as we do not have corresponding macro for MMC3
and MMC4.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Before disable cache, need to first flush cache.
There maybe dirty data in D-Cache before disable D-Cache.
After disable D-Cache, the first store instructions in
psci_v7_flush_dcache_all will directly store registers
{r4-r5, r7, r9-r11, lr} to memory.
If there is dirty data before disable D-Cache,
psci_v7_flush_dcache_all will flush data to memory,
and may overwrite the memory that hold the registers
{r4-r5, r7, r9-r11, lr}.
So before disable cache, first flush D-Cache.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tom Rini <trini@konsulko.com>
The rpi has a pretty simple way of resetting the whole system. All it takes
is to poke a few registers at a well defined location in MMIO space.
This patch adds support for the EFI loader implementation to allow an OS to
reset and power off the system when we're outside of boot time.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch removes use of U_BOOT_DEVICE in board/raspberrypi/rpi/rpi.c,
enables OF_CONTROL in the config and adjusts the rpi_*defconfig configs.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The information currently set via platdata has to be represented in the
device tree now. bcm283x-uboot.dtsi adds the u-boot specific "skip-init"
property to the serial nodes and enables initialization in the pre-reloc phase.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds device trees for the bcm283x platform to be used with
OF_CONTROL. The version 4.8-rc7 of the linux kernel was used as source.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The config option TARGET_K2x_EVM is set by the k2x defconfigs to pick
a board target, but the header configs also set K2x_EVM. This config
is redundant, remove it and use TARGET_K2x_EVM everywhere in its place.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add board support for sun8i_r16 Nintendo NES Classic edition.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
[jagan: Add commit message body]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Currently, USB is forced-enabled for the sunxi familly, and there is no
way to disable it.
However, USB takes a long time to initiliase, delaying the boot by up to
5 seconds (without any USB device attached!). This is a very long delay,
especially in cases where USB booting is not wanted at all, and where
the device is expected to boot relatively often (even in production).
Change the way the dependencies are handled, by only forcibly selecting
USB when CONFIG_DISTRO_DEFAULTS ("defaults suitable for booting general
purpose Linux distributions") is set. This option defaults to y for the
sunxi familly, so the current default behaviour is kept unchanged. Users
interested in boot time and/or size will be able to disable this to
further disable USB.
With USB disabled, the time spent in U-Boot before handing control to
the Linux kernel is about 1s now, down from ~5s (Nanopi Neo, sunxi H3).
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Today we can compile a self-contained hello world efi test binary that
allows us to quickly verify whether the EFI loader framwork works.
We can use that binary outside of the self-contained test case though,
by providing it to a to-be-tested system via tftp.
This patch separates compilation of the helloworld.efi file from
including it in the u-boot binary for "bootefi hello". It also modifies
the efi_loader test case to enable travis to pick up the compiled file.
Because we're now no longer bloating the resulting u-boot binary, we
can enable compilation always, giving us good travis test coverage.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for the Asus Chromebook Flip, an RK3288-based clamshell
device which can flip into 'tablet' mode. The device tree file comes from
Linux v4.8. The SDRAM parameters are for 4GB Samsung LPDDR3.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds support for the Asus Chromebit, and RK3288-based device designed
to plug directly into an HDMI monitor. The device tree file comes from
Linux v4.8.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update board_init() to increase the ARM clock to the maximum speed on
veyron boards. This makes quite a large difference in performance. With
this change, speed goes from about 750 DMIPS to 2720 DMIPs.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have a single rk3288-based Chromebook: chromebook_jerry. But
all such Chromebooks can use the same binary with only device-tree
differences. The family name is 'veyron', so rename the files accordingly.
Also update the device-tree filename since this currently differs from
Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Check whether a display device is in use before using it. Add a comment as
to why two displays cannot currently be used at the same time.
This allows us to remove the device-tree change that disables vopb on
jerry.
Signed-off-by: Simon Glass <sjg@chromium.org>
This board always boots from SPI, so update the code to support that with
of-platdata. The boot source is not currently available with of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
As PSCI and secure monitor firmware framework are enabled, this patch is
to support loading 32-bit OS in such case. The default target exception
level returned to U-Boot is EL2, so the corresponding work to switch to
AArch32 EL2 and jump to 32-bit OS are done in U-Boot and secure firmware
together.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Spin-table method is used for secondary cores to load 32-bit OS. The
architecture information will be got through checking FIT image and
saved in the os_arch element of spin-table, then the secondary cores
will check os_arch and jump to 32-bit OS or 64-bit OS automatically.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To support loading a 32-bit OS, the execution state will change from
AArch64 to AArch32 when jumping to kernel.
The architecture information will be got through checking FIT image,
then U-Boot will load 32-bit OS or 64-bit OS automatically.
Signed-off-by: Ebony Zhu <ebony.zhu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the custom low-level initialization function and reuse the
default low-level initialization function. But this requires the
ARMV8_MULTIENTRY config option to be enabled for Exynos7420.
On Exynos7420, the boot CPU belongs to the second cluster and so
with ARMV8_MULTIENTRY config option enabled, the 'branch_if_master'
macro fails to detect the CPU as boot CPU. As a temporary workaround
the CPU_RELEASE_ADDR is set to point to '_main'.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP ARMv8 SoC LS2080A release all secondary cores in one-go.
But other new SoCs like LS2088A, LS1088A release secondary
cores one by one.
Update code to release secondary cores based on SoC SVR
Add code to release cores one by one for non LS2080A SoCs
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: remove "inline" from declaration of initiator_type]
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS2088A SoC is built on layerscape architecture.
It is similar to LS2080A SoC with some differences like
1)Timer controller offset is different
2)It has A72 cores
3)It supports TZASC module
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080 SoC and its personalities does not support TZASC
But other new SoCs like LS2088A, LS1088A supports TZASC
Hence, skip initializing TZASC for Ls2080A based on SVR
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TZASC registers like TZASC_GATE_KEEPER, TZASC_REGION_ATTRIBUTES
are 32-bit regsiters.
So while doing register load-store operations, 32-bit intermediate
register, w0 should be used.
Update x0 register to w0 register type.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Timer controller base address has been changed from
LS2080A SoC (and its personalities) to new SoCs like
LS2088A, LS1088A.
Use SVR based timer base address detection to avoid compile time #ifdef.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Implement a hook to allow boards to save boot-time CPU state for later
use. When U-Boot is chain-loaded by another bootloader, CPU registers may
contain useful information such as system configuration information. This
feature mirrors the equivalent ARMv7 feature.
Signed-off-by: Cédric Schieli <cschieli@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
With the move to arch/arm/mach-omap2 there are now very few uses of
CONFIG_OMAP_COMMON and further they can all be replaced with
CONFIG_ARCH_OMAP2, so do so.
Signed-off-by: Tom Rini <trini@konsulko.com>
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories. All refernces to the former locations are updated to
the current locations. For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.
Signed-off-by: Tom Rini <trini@konsulko.com>
To start consolidating various TI-related code, introduce the ARCH_OMAP2
symbol. While we have removed omap2-specific boards some time ago,
matching up with the kernel naming here will help overall.
Signed-off-by: Tom Rini <trini@konsulko.com>
Detect the board very early and avoid reading eeprom multiple times.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is similar to Commit 93e6253d11 ("ARM: OMAP4/5: Centralize
early clock initialization") that was done for OMAP4+, reflecting the same
for AM33xx and AM43xx SoCs to centralize clock initialization.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add setup_early_clocks that calls setup_clocks_for_console for
ti81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update CONFIG_LS2080A to CONFIG_FSL_LSCH3 to make those workaround
implementing of erratum reusable for more SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch adds support for Freescale ls1021a-iot board.
Signed-off-by: Feng Li <feng.li_2@nxp.com>
[YS: rewrite commit message, fix whitespace in Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
Early system initialization is being done before initf_dm is being called
in U-Boot. Then system will fail to boot if any of the DM enabled driver
is being called in this system initialization code. So, rearrange the
code a bit so that DM enabled drivers can be called during early system
initialization. This is inspired by commit e850ed82bc ("ARM: OMAP4+: Allow
arch specific code to use early DM")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Set the appropriate bits in the interface config register based
on the SPI_ mode flags.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xmR3
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2016-11-17
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
When implementing efi loader support, we can expose runtime services
for payloads. One such service is CPU reset.
This patch implements RTS CPU reset support for layerscape systems.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
The efi loader code has its own memory map, so it needs to be aware where
the spin tables are located, to ensure that no code writes into those
regions.
Signed-off-by: Alexander Graf <agraf@suse.de>
On ls2080 we have a separate network fabric component which we need to
shut down before we enter Linux (or any other OS). Along with that also
comes configuration of the fabric using a description file.
Today we always stop and configure the fabric in the boot script and
(again) exit it on device tree generation. This works ok for the normal
booti case, but with bootefi the payload we're running may still want to
access the network.
So let's add a new fsl_mc command that defers configuration and stopping
the hardware to when we actually exit U-Boot, so that we can still use
the fabric from an EFI payload.
For existing boot scripts, nothing should change with this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
[agraf: Fix x86 build]
The NXP ls1043 and ls1046 systems do not (yet) have PSCI enablement
for reset. Don't enable generic PSCI reset code on them.
Signed-off-by: Alexander Graf <agraf@suse.de>
According to design team, we need to set REFTOP_VBGADJ
in PMU MISC0 according to the REFTOP_TRIM[2:0] fuse. the
actually table is as below:
'000" - set REFTOP_VBGADJ[2:0] to 3'b000
'001" - set REFTOP_VBGADJ[2:0] to 3'b001
'010" - set REFTOP_VBGADJ[2:0] to 3'b010
'011" - set REFTOP_VBGADJ[2:0] to 3'b011
'100" - set REFTOP_VBGADJ[2:0] to 3'b100
'101" - set REFTOP_VBGADJ[2:0] to 3'b101
'110" - set REFTOP_VBGADJ[2:0] to 3'b110
'111" - set REFTOP_VBGADJ[2:0] to 3'b111
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Need to gate ENET clock when switching to a new clock parent, because
the mux is not glitchless.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye.Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Adding prefetchable memory space to pcie device tree node.
Shifting configuration space to 64-bit address space.
Removing pcie device tree node from amba as it requires size-cells=<2>
in order to access 64-bit address space.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynqmp DMA driver expects two clocks (main clock and apb clock)
For LPDDMA channels the two clocks are missing in the
Dma node resulting probe failure.
xilinx-zynqmp-dma ffa80000.dma: main clock not found.
xilinx-zynqmp-dma ffa80000.dma: Probing channel failed
xilinx-zynqmp-dma: probe of ffa80000.dma failed with error -2
This patch fixes this issue.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
LPDDMA default allows only secured access.
inorder to enable these dma channels,
one should ensure that it allows non secure access.
This patch updates the same.
Reported-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use 64bit size cell for main amba bus instead of 32bit because PCIe
node requires it Change 64bit sizes also for all others IPs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This reverts commit bd750e7a6c
Implemented the new workaround for auto tuning based on
zynqmp compatible string, so removed the 'broken-tuning'
property.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changes the compatible string for sdhci node,
adds "xlnx,device_id" and "xlnx,mio_bank" property to sdhci node.
Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds edac node for arm cortexa53 to report
errors on L1 and L2 caches.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This reverts commit 786db82bd5.
Since we are using serdes driver , no need of mapping serdes register
space into DP driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Tested-by: Hyun Kwon <hyunk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Each plane can be associated with multiple DMA channels. So add
index for each DMA channel.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Updating required device tree changes as per mainlined driver
from 4.6 kernel.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Previously, it was assumed that there is a 1:1 mapping between
PM ID defined in the platform firmware and a PM domain. However, there
can be a situation where multiple PM IDs belong to a single PM domain
(e.g. PM IDs for GPU and two pixel processors correspond to a single
PM domain).
This patch adds support for assigning more than one PM ID to
a single PM domain.
Updated documentation accordingly.
Assigned pixel processors PM IDs to GPU PM domain.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DDR power states are handled by the PM firmware, so this domain is
redundant. Also, since there is no device using this PM domain,
it will be powered off during boot, which is wrong.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add dcc to dtsi for supporting system without serial port.
DCC is enabled by default on ZynqMP.
Adding dcc to zcu100 and zcu102 which were tested.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynqmp DMA driver expects two clocks (main clock and apb clock)
LPDDMA clock cofiguration is missing for the same in the
zynqmp-clk.dtsi file.
This patch updates for the same.
Reported-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DTC 1.4.2 reports these warnings:
Warning (unit_address_vs_reg): Node /amba_apu has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /amba has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /amba/usb@fe200000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node /amba/usb@fe300000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video0channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video1channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video2channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-graphicschannel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-audio0channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-audio1channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
This patch is fixing them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DTC 1.4.2 reports these warnings:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /pmu has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name,
but no reg property
This patch is fixing them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not setup use_alt bit which copy alternative boot mode to
boot mode. The reason is that this bit is cleared after POR
but not after any software reset which will cause
that after SW reset bootrom will look for different boot image.
This patch setups alternative boot mode selection (purely SW
handling) and extends code to read this alternative boot mode first and
use it if it is setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for SD1 with level shifters bootmode.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to check the buswidth on nand flash
at runtime based on nand MIO configurations done by FSBL.
User needs to correctly configure the MIO's based on the
buswidth supported by the nand flash which is present on the board.
Added nand8 and nand16 @periph names on slcr driver.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The topic-miami SoMs contain a Zynq xc7z015 or xc7z030 SoC, 1GB DDR3L RAM,
32MB QSPI NOR flash and 256MB NAND flash.
The topic-miamiplus SoMs contain a Zynq xc7z035, xc7z045 or xc7z100 SoC,
2x 1GB DDR3L RAM, 64MB dual-parallel QSPI flash, clock sources
and a fan controller.
The "Florida" carrier boards add SD, USB, ethernet and other interfaces.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a string description for SYS_VENDOR to allow configuring boards from
other vendors than just "xilinx".
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Zynq/ZynqMP boot.bin file contains a region for register initialization
data. Filling in proper values in this table can reduce boot time
(e.g. about 50ms faster on QSPI boot) and also reduce the size of
the SPL binary.
The table is a simple text file with register+data on each line. Other
lines are simply skipped. The file can be passed to mkimage using the
"-R" parameter.
It is recommended to add reg init file to board folder.
For example:
CONFIG_BOOT_INIT_FILE="board/xilinx/zynqmp/xilinx_zynqmp_zcu102/reg.int
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for EFI apps on aarch64. This includes start-up and relocation
code plus a link script.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agraf: add kconfig dep]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add support for EFI apps on ARM. This includes start-up and relocation
code, plus a link script and some compiler setting changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agraf: Remove whitespace change, add kconfig dep]
Signed-off-by: Alexander Graf <agraf@suse.de>
Rather than hard-coding the relocation type, add it to the ELF header file
and use it from there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Update the spi-max-frequency property of m25p80 flash slave to match
that of TI QSPI controller node, so that QSPI operations happen at
maximum supported frequency of 76.8MHz.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Update the PLL initialization sequence to avoid glitches while
programming. User guide for the same is available at[1].
[1] http://www.ti.com/lit/ug/sprugv2h/sprugv2h.pdf
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
While we setup the mmu initially we mark set_section_dcache with
DCACHE_OFF flag. In case of non-LPAE mode the DCACHE_OFF macro
is rightly defined with TTB_SECT_XN_MASK set so as to mark all the
4GB XN. In case of LPAE mode XN(Execute-never) bit is not set with
DCACHE_OFF. Hence XN bit is not set by default for DCACHE_OFF which
keeps all the regions execute okay and this leads to random speculative
fetches in random memory regions which was eventually caught by kernel
omap-l3-noc driver.
Fix this to mark the regions as XN by default.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
An SMC call is required for all cache-wide operations on Tegra186. This
patch implements the two missing hooks now that U-Boot supports them, and
fixes the mapping of "hook name" to SMC call code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
SoC-specific logic may be required for all forms of cache-wide
operations; invalidate and flush of both dcache and icache (note that
only 3 of the 4 possible combinations make sense, since the icache never
contains dirty lines). This patch adds an optional hook for all
implemented cache-wide operations, and renames the one existing hook to
better represent exactly which operation it is implementing. A dummy
no-op implementation of each hook is provided.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When performing a cache disable function, code must not access DRAM.
That is because when the cache is disabled, it will be bypassed and all
loads and stores will be serviced by RAM. This prevents accessing any
dirty data in the cache. In turn, this means the stack cannot be
used, since that is in RAM. To guarantee that code doesn't use RAM (and
in particular the stack) __asm_flush_l3_cache() must be manually
implemented in assembly, rather than implemented in C since the compiler
won't know not to touch RAM.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
nvtboot_boot_x0 is a 64-bit variable and hence must be 64-bit aligned.
So far this has happened by accident! Fix the code so this is guaranteed.
This fixes the following build error:
... relocation truncated to fit: R_AARCH64_LDST64_ABS_LO12_NC
against symbol `nvtboot_boot_x0' ...
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable the Ethernet device in DT, provide board-specific configuration,
and enable the driver in Kconfig.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tegra186 includes a Synopsys DWC EQoS (Ethernet) device. Add this to the
Tegra186 SoC DT so that boards can make use of it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On Tegra186, the bootloader which runs before U-Boot passes the Ethernet
MAC address to U-Boot using device tree. Extract this value and write it
to the environment, so that the Ethernet uclass picks it up and uses it
for the built-in Ethernet device.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extend the Tegra186 implementation of board_late_init() to call a per-SoC
"hook" function. This will allow SoC-specific (rather than Tegra-wide)
functionality to be implemented without the core Tegra code needing to be
aware of the details. While board186.c is currently only used for
Tegra186, it should be applicable to any other future SoC, and perhaps its
simple design could be back-ported to older SoCs in the future too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For 64-bit ARM systems we provide just a timer_read_counter()
implementation and rely on the generic non-uclass get_ticks() function
in lib/time.c to call the former.
However this function is actually not 64-bit safe, as it assumes a
"long" to be 32-bit. Beside the fact that the resulting uint64_t
isn't bigger than "long" on 64-bit architectures and thus combining two
counters makes no sense, we get all kind of weird results when we try
to OR in the high value shifted by _32_ bits.
So let's avoid that function at all and provide a straight forward
get_ticks() implementation for ARMv8, which also is in line with ARMv7.
This fixes occasional immediate time-out expiration issues I see on the
Pine64 board. The root cause of this needs to be investigated, but this
fix looks like the right thing anyway.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Cover-Letter: Fixes several spelling errors for the words "resetting",
"extended", "occur", and "multiple".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL_MMC_SUPPORT defined in rockchip top level Kconfig instead of
inside rk3288 and default to disable if ROCKCHIP_SPL_BACK_TO_BROM
defined.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since we implement the dram capacity auto detect, we don't
need to set the channel number and sdram-channel in dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Add support for rk3288 dram capacity auto detect, support DDR3 and
LPDDR3, DDR2 is not supported.
The program will automatically detect:
- channel number
- rank number
- column address number
- row address number
The dts file do not need to describe those info after apply this patch.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
The Clock Multiplier in rk3399 EMMC programmable clock generator
is broken, we can remove its support from SoC GRF register.
Without this patch, rk3399 emmc driver is not work after below patch
applied:
6dffdbc mmc: sdhci: Add the programmable clock mode support
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Also rename the driver symbol to be more consistent with the other rockchip
clock drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Also rename the driver symbol to be more consistent with the other rockchip
clock drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A80 has SID e-fuses. Like other newer SoCs, the actual e-fuses
are at an offset of 0x200 within the SID address space.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sun8i-emac driver works fine with the A64 Ethernet IP, but we are
missing an alias entry to trigger the driver instantiation by U-Boot.
Add the line to point U-Boot to the Ethernet DT node.
This enables TFTP boot on the Pine64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This is a cleaned up version set_pll() from Allwinner's boot0 source
(bootloader/basic_loader/bsp/bsp_for_a80/common/common.c).
[wens@csie.org: Added commit message; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Since the A80 has many cores which we intend to use in SMP fashion,
we should set the SMP bit for the boot CPU.
[wens@csie.org: Added commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On sun9i, the GTBUS manages transaction priority and bandwidth
for multiple read ports when accessing DRAM. The initialisation
mirrors the settings from Allwinner's boot0 for now, even though
this may not be optimal for all applications (e.g. headless
systems might want to give priority to IO modules).
Adding a common callout to gtbus_init() from the SPL clock init
with a weakly defined implementation in sunxi/clock.c to fallback
to for platforms that don't require this.
[wens@csie.org: Moved gtbus_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds DRAM initialisation code for sun9i, which calculates the
appropriate timings based on timing information for the supplied
DDR3 bin and the clock speeds used.
With this DRAM setup, we have verified DDR3 clocks of up to 792MHz
(i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration.
[wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks]
[hdegoede@redhat.com: Fix checkpatch warnings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add the LD11 SoC data and adjuts the printf() format because this is
a 64-bit SoC. Otherwise, 16-digits pointer addresses would break
the log format.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Do not hard-code the number of DX blocks because it is a different
value for LD11 SoC.
Move the macro NR_DATX8_PER_DDRPHY to ddrphy-training.c since it
is the last user.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DDR PHY register view of LD11 is slightly different from that
of LD4/Pro4/sLD8, but it will be possible to share the register
macros (and I want to re-use as much code as possible). Change
the code in the more flexible form.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The USB boot without the stand-by MPU is available on ES3 or later
of LD11 SoC, but the code in this if-conditional block must not be
run when booting from USB. Check if the boot device is USB, and
skip the code in the case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At the moment, the clk driver is not clever enough to automatically
enable parent clocks like Linux. Enable the STDMAC clock explicitly
if USB is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This PHY might be used for other SoCs in the future.
Avoid including the SoC name in the header name.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The environment fdt_file is useful to remember the appropriate DTB
file name. Adjust it to the recent renaming in the upstream kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix the warning from dtc like,
---8<----
Warning (unit_address_vs_reg): Node /ahb/apb/pmc@f0014000/periph64ck/sdmmc0_hclk has a reg or ranges property, but no unit name
--->8----
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
add at least icache support for at91 based boards.
This speeds up NOR flash access on an at91sam9g15
based board from 15.2 seconds reading 8 MiB from
a SPI NOR flash to 5.7 seconds.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
on at91sam9x5 PRES offset is 4 in the PMC master
clock register.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Andreas Bießmann <andreas@biessmann.org>
To enable configuration of sdr.ctrlcfg.extratime1 register which enable
extra clocks for read to write command timing. This is critical to
ensure successful LPDDR2 interface
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
i.CoreM6 Quad/Dual modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DQ, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add imx6q pinctrl defines support from Linux.
Here is the last commit:
"ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ"
(sha1: d8c765e0d1ddbd5032c2491c82cc9660c2f0e7f2)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add i.MX6Q dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DL, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add imx6dl pinctrl defines support from Linux.
Here is the last commit:
"ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ"
(sha1: d8c765e0d1ddbd5032c2491c82cc9660c2f0e7f2)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add i.MX6DQL dtsi support from Linux.
Here is the last commit:
"ARM: dts: imx6qdl: Fix SPDIF regression"
(sha1: f065e9e4addd75c21bb976bb2558648bf4f61de6)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add i.MX6DL dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot Log for i.CoreM6 DualLite/Solo Starter Kit:
-----------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6SOLO rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
DRAM: 256 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
6741808 bytes read in 341 ms (18.9 MiB/s)
Booting from mmc ...
reading imx6dl-icore.dtb
30600 bytes read in 19 ms (1.5 MiB/s)
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800a787
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
Boot Log for i.CoreM6 Quad/Dual Starter Kit:
--------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6Q rev1.2 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
icorem6qdl>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Commit b02e4044ff ("libfdt: Bring in upstream stringlist
functions") broke codying style in some places especially
by inserting an extra whitespace before fdt_stringlist_count().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
If CONFIG_USE_IMXIMG_PLUGIN is selected, plugin.bin will be
generated under board/$(BOARDDIR)/.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add mx7_plugin.S which calls boot rom setup function, generate the second ivt,
and jump back to boot rom.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add mx6_plugin.S which calls boot rom setup function, generate the second ivt,
and jump back to boot rom.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Highlights this time around:
- Add run time service (power control) support for PSCI (fixed in v3)
- Add efi gop pointer exposure
- SMBIOS support for EFI (on ARM)
- efi pool memory unmap support (needed for 4.8)
- initial x86 efi payload support (fixed up in v2)
- various bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=peNm
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2016-10-19
Highlights this time around:
- Add run time service (power control) support for PSCI (fixed in v3)
- Add efi gop pointer exposure
- SMBIOS support for EFI (on ARM)
- efi pool memory unmap support (needed for 4.8)
- initial x86 efi payload support (fixed up in v2)
- various bug fixes
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
include/tables_csum.h
Compiler attributes are more commonly __foo style tags rather than big
upper case eye sores like EFI_RUNTIME_TEXT.
Simon Glass felt quite strongly about this, so this patch converts our
existing defines over to more eye friendly ones.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have generic PSCI reset and shutdown support in place, we can
advertise those as EFI Run Time Services, allowing efi applications and
OSs to reset and shut down systems.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Most armv8 systems have PSCI support enabled in EL3, either through
ARM Trusted Firmware or other firmware.
On these systems, we do not need to implement system reset manually,
but can instead rely on higher level firmware to deal with it.
The exclude list seems excessive right now, but NXP is working on
providing an in-tree PSCI implementation, so that all NXP systems
can eventually use PSCI as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf: fix meson]
Reviewed-by: Simon Glass <sjg@chromium.org>
Using PSCI you can not only reset the system, you can also shut it down!
This patch exposes a function to do exactly that to whatever code wants
to make use of it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
All systems that are running on armv8 are running bare metal with firmware
that implements PSCI running in EL3. That means we don't really need to expose
the hypercall variants of them.
This patch leaves the code in, but makes the code explicit enough to have the
compiler optimize it out. With this we don't need to worry about hvc vs smc
calling convention when calling psci helper functions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit "2bb014820c49a63902103bac710bc86b5772e843"
do some clean up to use the code in lib/time.c.
But usec2ticks is still being used by security related job ring code.
Bring back the function to avoid build break when CONFIG_FSL_CAAM
is defined.
The computation logic has been changed, using 64-bit variable
to ease the process, making it work on older (MX5) platforms.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Jon Master reports that QEMU refuses to load a U-Boot image built
with CONFIG_ARMV7_NONSEC, but without CONFIG_ARMV7_PSCI since
commit 5a3aae68c7 ("ARM: armv7: guard memory reserve for PSCI
with #ifdef CONFIG_ARMV7_PSCI").
It looks like only PSCI that needs the Secure stack, so move
the #ifdef to guard the whole of .secure_stack allocation in order
not to create the empty section.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Jon Masters <jcm@redhat.com>
Link: http://patchwork.ozlabs.org/patch/664025/
The signature for this macro has changed. Bring in the upstream version and
adjust U-Boot's usages to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update to drivers/power/pmic/palmas.c:
Signed-off-by: Keerthy <j-keerthy@ti.com>
Change-Id: I6cc9021339bfe686f9df21d61a1095ca2b3776e8
These have now landed upstream. The naming is different and in one case the
function signature has changed. Update the code to match.
This applies the following upstream commits by
Thierry Reding <treding@nvidia.com> :
604e61e fdt: Add functions to retrieve strings
8702bd1 fdt: Add a function to get the index of a string
2218387 fdt: Add a function to count strings
Signed-off-by: Simon Glass <sjg@chromium.org>
ARM CPUs can architecturally (speculatively) prefetch completely arbitrary
normal memory locations, as defined by the current translation tables. The
current MMU configuration for 64-bit Tegras maps an extremely large range
of addresses as DRAM, well beyond the actual physical maximum DRAM window,
even though U-Boot only needs access to the first 2GB of DRAM; the Tegra
port of U-Boot deliberately limits itself to 2GB of RAM since some HW
modules on at least some 64-bit Tegra SoCs can only access a 32-bit
physical address space. This change reduces the amount of RAM mapped via
the MMU to disallow the CPU from ever speculatively accessing RAM that
U-Boot will definitely not access. This avoids the possibility of the HW
raising SError due to accesses to always-invalid physical addresses.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Without this patch the following error will be shown:
Colibri T20 # usb start
starting USB...
No controllers found
This patch fixes USB operation and also the controller order as the
CI UDC driver may only be instantiated on the first aka OTG port.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Without this patch the following error will be shown:
stdio_add_devices: Video device failed (ret=-22)
As commit ec5507707a (video: tegra: Move
to using simple-panel and pwm-backlight) states the Colibri T20 needs
updating too which this patch finally attempts doing.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
H3 seems to have a silicon bug breaking the impedance calibration.
This is currently worked around in software by multiple steps
combining the results to replace the wrong values.
Revision A chips need a different workaround, which is present in
the vendor bootloader too, but got overlooked in lack of
information and affected boards till now.
This commit adds a simplified version without correction factor,
which would be 1.00 for all known boards anyway.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This is the initial commit for UniPhier reset controller driver.
Most code was ported from Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As for LD11/LD20, we can no longer rely on the udelay() in the PLL
init functions. udelay(200) is needed here to keep the ethernet
device in the reset state for enough time. Anyway, 200 usec is
quite short for humans, so nobody cares it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Raise the VDD09 voltage line to 1.0V to suppress VBO noise.
This errata work-around code is needed only for ES1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Do not reference CONFIG_DDR_FREQ; now the DDR frequency
is passed from the uniphier_board_data structure
- Constify parameter arrays
- Tidy up cluttered macros
- Lots of code cleanups
- Lots of coding style fixes
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For LD11 and LD20 SoCs, the System Bus and NAND are multiplexed
in the same I/O pins. When booting from a NAND device, pin-mux
for the System Bus must not be set-up because they are exclusive
with each other.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Synology DS109 is based on MV88F6281. The code
is based on Dreamplug code with modificatons
from Synologys open source repository.
Signed-off-by: Walter Schweizer <swwa@users.sourceforge.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Add silicon ID code for AM437x silicon. This can be used to print
the cpu info using CONFIG_DISPLAY_CPUINFO.
Also printing "CPU :" along with cpu name in order to be consistent
with other OMAP platforms.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The normal longjmp command allows for a caller to pass the return value
of the setjmp() invocation. This patch adds that semantic to the arm
implementation of it and adjusts the efi_loader call respectively.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The KeyStone platform has its own clk_get_rate() but its prototype
is different from that of the common-clk (clk-uclass) framework.
Prefix the KeyStone specific implementation with ks_ in order to
avoid name-space conflict.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the USB node for LS2080a in dts.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
[York Sun: replace ls2080 with ls2080a in commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
These two functions are neither defined nor referenced.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
To create the soc environment variable we concatenate two strings
on the stack. So far, strcat has been used for the first string as
well as for the second string. Since the variable on the stack is
not initialized, the first strcat may not start using the first
entry in the character array. This then could lead to an buffer
overflow on the stack.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add device tree node for Ricoh RN5T567. Currently we do not need
the individual DC/DC converters or LDO's (and they are also not
yet supported by the driver).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Add base device for NXP i.MX 7Solo/7Dual. The two SoC are very
similar and hence can share the same device tree for boot loaders
purpose.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add pinctrl defines for NXP i.MX 7Solo/7Dual SoC. The pinctrl format
is compatible to the Linux kernel, hence this file is a simple copy
from the Linux kernel (commit 97f5c1817b7e).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Override the switch_to_hypervisor function to switch cpu to hypervisor
mode using the available ROM code hook early in the boot phase before
the boot loader checks for HYP mode.
Based on the work done by Jonathan Bergsagel jbergsagel@ti.com.
Cc: beagleboard-x15@googlegroups.com
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On some of the SoCs one cannot enable hypervisor mode directly from the
u-boot because the ROM code puts the chip to supervisor mode after it
jumps to boot loader. Hence introduce a weak function which can be
overridden based on the SoC type and switch to hypervisor mode in a
custom way.
Cc: beagleboard-x15@googlegroups.com
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Cache configuration methods is different for LPAE and non-LPAE cases.
Hence the bits and the interpretaion is different for two cases.
In case of non-LPAE mode short descriptor format is used and we need
to set Cache and Buffer bits.
In the case of LPAE the cache configuration happens via MAIR0 lookup.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As of now the mmu section shift is hardcoded to 20 but with LPAE
coming into picture this can be different. Hence replacing 20 with
MMU_SECTION_SHIFT macro.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are needed in UBI/UBIFS on ZynqMP platform (ARM64).
Signed-off-by: Adam Oleksy <adam.oleksy@nokia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Fix various misspellings of:
* deprecated
* partition
* preceding,preceded
* preparation
* its versus it's
* export
* existing
* scenario
* redundant
* remaining
* value
* architecture
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
When enabled sec firmware framework, but lack of definition of
the marco SEC_FIRMWARE_FIT_IMAGE, SEC_FIRMEWARE_FIT_CNF_NAME
and SEC_FIRMWARE_TARGET_EL, there will be some build errors,
so give a default definition.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
The SPL and U-Boot proper may use different initial stack
locations, which are configured via CONFIG_SPL_STACK and
CONFIG_SYS_INIT_SP_ADDR defines. The lowlevel_init.S
code needs to handle this in the same way as crt0.S
Without this fix, setting the U-Boot stack location to some
place, which is not safely accessible by the SPL (such as
the DRAM), causes a very early SPL deadlock.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rather than having a global variable, pass the spl_image as a parameter.
This avoids BSS use, and makes it clearer what the function is actually
doing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Update existing users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present some spl_xxx_load_image() functions take a parameter and some
don't. Of those that do, most take an integer but one takes a string.
Convert this parameter into a struct so that we can pass all functions the
same thing. This will allow us to use a common function signature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this option to Kconfig and tidy up existing uses. Also add a function
comment to the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this is only used on ARM and sandbox, but it is just as
applicable to other architectures. Move the function prototype into the
generic SPL header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move DDR3, DDR4 and related config options to Kconfig and clean up
existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move DDR3, DDR4 and realted options to Kconfig and clean up existing
uses.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this option to Kconfig and clean up existing uses.
NUM_DDR_CONTROLLERS is also used by PowerPC SoCs.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this option to Kconfig and clean up existing uses.
This option is also used by PowerPC SoCs.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move MAX_CPUS option to Kconfig and clean up existing uses for ARM. This
option is used by Freescale Layerscape SoCs.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move these options to Kconfig and create a sub-menu to avoid name
conflict with other architectures.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some config options should not have prompt. They are selected by choosing
target.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SYSCLK is used as a reference clock for USB. When the USB controller
is used, SYSCLK must meet the additional requirement of 100 MHz.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Pin mux logic has 2 options in priority order, one is through RCW_SRC
and then through RCW_Fields. In case of QSPI booting, RCW_SRC logic
takes the priority for SPI pads and do not allow RCW_BASE and SPI_EXT
to control the SPI muxing. But actually those are DSPI controller's
pads instead of QSPI controller's, so this workaround allows RCW
fields SPI_BASE and SPI_EXT to control relevant pads muxing.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Following commits 217f92b and 1544698, these two config
CPU_V7_HAS_NONSEC and CPU_V7_HAS_VIRT are moved to Kconfig,
for correctly select ARMV7_PSCI.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The core position is not continuous for some SoCs. For example,
valid cores may present at position 0, 1, 4, 5, 8, 9, etc. Some
registers (including boot release register) only count existing
cores. Current implementation of cpu_mask() complies with the
continuous numbering. However, command "cpu status" queries the
spin table with actual core position. Add functions to calculate
core position from core number, to correctly calculate offsets.
Tested on LS2080ARDB and LS1043ARDB.
Signed-off-by: York Sun <york.sun@nxp.com>
The exact SoC revsion number can be recognized from U-Boot log.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Delete CONFIG_SKIP_LOWLEVEL_INIT define in ls1021atwr.h and
ls1021aqds.h can let it run cpu_init_cp15 to enable i-cache. First
stage of u-boot can run faster after that. There is a description
about skip lowlevel init in board/freescale/ls1021atwr/README.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
By default the SATA IP on the ls1043a/ls1046a SoCs does not
generating coherent/snoopable transactions. This patch enable
it in the SCFG_SNPCNFGCR register along with sata axicc register.
In addition, the dma-coherent property must be set on the SATA
controller nodes.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The default values for Port Phy2Cfg register and
Port Phy3Cfg register are better, no need to overwrite them.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This format can be flashed directly at address 0 of
the NAND FLASH, as it contains all necessary headers.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
>From TO1.1, SNVS adds internal pull up control for POR_B,
the register filed is GPBIT[1:0], after system boot up,
it can be set to 2b'01 to disable internal pull up.
It can save about 30uA power in SNVS mode.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
For i.MX6, the mux width is 4, not 3. So enlarge the width.
IOMUX_CONFIG_LPSR is changed from 0x8 to 0x20 to not use bit 3 of mux.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Currently the bmode "usb" uses BOOT_CFG1 to 0x01, -which means
BOOT_CFG1[7:4] is set to b0000. According to Table 8-7 Boot
Device Selection this is NOR/OneNAND and not Reserved.
Use 0x10 which leads to b0001, which is a Reserved boot device.
With that the SoC reliably falls back to the serial loader.
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.
Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)
CPU: Freescale i.MX6ULL rev1.0 at 396MHz
CPU: Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM: 512 MiB
MMC: initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add pinctrl defines for NXP i.MX 6ULL.
Since i.MX6ULL reuses some definitions of i.MX6UL,
also add i.MX6UL pinctrl defines from linux kernel commit (29b4817d401).
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
SNVS TAMPER pin and BOOT MODE pins are in SNVS IOMUXC module,
not in IOMUXC, so correct the related registers' offset.
Use IOMUX_CONFIG_LPSR flag for these pins, so we can differentiate
them from iomuxc pins.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau.dev@gmail.com>
Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage
is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop
MISC0 bit[6:4]) setting to 2b'110.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since the mx6ull adds the AIPS3, so enable its initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update memory map address for mx6ull.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update Clock settings and CCM register map for i.MX6ULL.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update misc SOC related settings for i.MX6ULL, such as FEC mac address,
cpu speed grading and mmdc channel mask clearing.
Also update s_init to skip pfd reset.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since MX6ULL select MX6UL, we can not use IS_ENABLED(CONFIG_MX6UL) here,
because this piece code is only for i.MX6UL.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Rom already initialized clock at 396M and 132M for arm core and ahb,
so skip setting them again in U-Boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
i.MX6ULL is derivative from i.MX6UL, so select MX6UL for MX6ULL.
If need to differenate MX6ULL from MX6UL, use CONFIG_MX6ULL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX6ULL major cpu type.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The CPU detection macro is_mx6dq returns 0 on an i.MX6DQP, so we need to
check for it explicitly in order to correctly initialize the pads when
CONFIG_MX6QDL is defined.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Like OMAP54xx and AM43xx family SoCs, AM33xx based SoCs have high
security enabled models. Allow AM33xx devices to be built with
HS Device Type Support.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
The option SPL_SPI_SUPPORT is used to enable support in SPL for loading
images from SPI flash, it should not be used to determine the build type
of the SPL image itself. The ability to read images from SPI flash does
not imply the SPL will be booted from SPI flash.
Unconditionally build SPI flash compatible SPL images.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropriate for the different boot modes.
For AM33xx devices additional image types are needed for
various SPL boot modes as the ROM checks for the name of
the boot mode in the file it loads.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
The config option AM33XX is used in several boards and should be
defined as a stand-alone option for this SOC. We break this out
from target boards that use this SoC and common headers then enable
AM33XX on in all the boards that used these targets to eliminate any
functional change with this patch.
This is similar to what has already been done in
9de852642cae ("arm: Kconfig: Add support for AM43xx SoC specific Kconfig")
and is done for the same reasons.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds a secure dram reservation fixup for secure
devices, when a region in the emif has been set aside
for secure world use. The size is defined by the
CONFIG_TI_SECURE_EMIF_TOTAL_REGION_SIZE config option.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
After EMIF DRAM is configured, but before it is used,
calls are made on secure devices to reserve any configured
memory region needed by the secure world and then to lock the
EMIF firewall configuration. If any other firewall
configuration needs to be applied, it must happen before the
lock call.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Create a few public APIs which rely on secure world ROM/HAL
APIs for their implementation. These are intended to be used
to reserve a portion of the EMIF memory and configure hardware
firewalls around that region to prevent public code from
manipulating or interfering with that memory.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds start address and size config options for setting aside
a portion of the EMIF memory space for usage by security software
(like a secure OS/TEE). There are two sizes, a total size and a
protected size. The region is divided into protected (secure) and
unprotected (public) regions, that are contiguous and start at the
start address given. If the start address is zero, the intention
is that the region will be automatically placed at the end of the
available external DRAM space.
Signed-off-by: Daniel Allred <d-allred@ti.com>
rockchip platform have a protocol to pass the the kernel reboot mode to bootloader
by some special registers when system reboot. In bootloader we should read it and take action.
We can only setup boot_mode in board_late_init becasue "setenv" need env setuped.
So add CONFIG_BOARD_LATE_INIT to common header and use a entry "rk_board_late_init"
to replace "board_late_init" in board file.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The latest rk3288-miniarm board doesn't have eMMC device, so remove it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a regulator-init-microvolt for vdd_center regulator
so that we can get a init value for driver probe.
Not like pmic regulator, the PWM regulator do not have a
known default output value, so we would like to init the
regulator when driver probe.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reference to kernel source code, rockchip pwm has three
type, we are using v2 for rk3288 and rk3399, so let's
update the register to sync with pwm_data_v2 in kernel.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update PPLL to 676MHz and PMU_PCLK to 48MHz, because:
1. 48MHz can make sure the pwm can get exact 50% duty ratio, but 99MHz
can not,
2. We think 48MHz is fast enough for pmu pclk and it is lower power cost
than 99MHz,
3. PPLL 676 MHz and PMU_PCLK 48MHz are the clock rate we are using
internally for kernel,it suppose not to change the bus clock like pmu_pclk
in kernel, so we want to change it in uboot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Default SPL_MMC_SUPPORT to false when ROCKCHIP_SPL_BACK_TO_BROM is enabled.
Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move back_to_bootrom() call later in SPL init so that the console is
initialized and printouts happen.
Currently when ROCKCHIP_SPL_BACK_TO_BROM is enabled there is no console
output from the SPL init stages.
I wasn't sure exactly where this should happen, so if we are set to do
run spl_board_init, then go back to bootrom there after
preloader_console_init(). Otherwise fall back to old behavior of doing
it in board_init_f.
Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The all current Rockchip SoCs supporting 4GB of ram have problems
accessing the memory region 0xfe000000~0xff000000. Actually, some IP
controller can't address to, so let's limit the available range.
This patch fixes a bug which found in miniarm-rk3288-4GB board. The
U-Boot was relocated to 0xfef72000, and .bss variants was also
relocated, such as do_fat_read_at_block. Once eMMC controller transfer
data to do_fat_read_at_block via DMA, DMAC can't access more than
0xfe000000. So that DMAC didn't work sane.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Given that boot monitor image is being generated to a specific target location
depending on the SoC and U-boot relies on addr_mon env variable to be aligned
with boot monitor target location. When ever the target address gets updated in
boot monitor, it is difficult to sync between u-boot and boot monitor and also
there is no way to update user that boot monitor image is updated.
To avoid this problem, boot monitor image is being generated with mkimage
header. Adding support in mon_install command for parsing this header.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On Tegra186, it is necessary to perform an SMC to fully flush all caches;
flushing/cleaning by set/way is not enough. Implement the required hook
to make this happen.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit ce02a71c23 "tegra: dts: Sync tegra20 device tree files with
Linux" enabled the ULPI USB port on Ventana, but made no attempt to ensure
that U-Boot code could handle this. In practice, various code is missing,
and various configuration options are not enabled, which causes U-Boot to
hang when attempting to initialize this USB port. This patch enables ULPI
PHY support on Ventana, and adds the required pinmux setup for the port to
operate. Note that Ventana is so similar to Seaboard that this change is
made in the Seaboard board file, which is shared with Ventana.
Seaboard also has the ULPI USB port wired up in hardware, although to an
internal port that often doesn't have anything attached to it. However,
the DT nodes for the USB controller and PHY had different status property
values, so the port was not initialized by U-Boot. Fix this inconsistency,
and enable the ULPI port, just like in the Linux kernel DT. This likewise
requires enabling ULPI support in the Seaboard defconfig.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some boards have a different set of USB controllers enabled in DT than
the set referenced by /alias entries. This patch fixes that. For
example, this avoids the following message while booting on Ventana,
which is caused by the fact that the USB0 controller had no alias, and
defaulted to wanting a sequence number of 0, which was later explicitly
requested by the alias for USB controller 2.
USB2: Device 'usb@c5008000': seq 0 is in use by 'usb@c5000000'
This didn't affect USB operation in any way though.
Related, there's no need for the USB controller aliases to have an order
that's different from the HW order, so re-order any aliases to match the
HW ordering. This has the benefit that since USB controller 0 is the only
one that supports device-mode in HW, and U-Boot only supports enabling
device move on controller 0, there's now good synergy in the ordering! For
Tegra20, that's not relevant at present since USB device mode doesn't work
correctly on that SoC, but it will save some head-scratching later.
This patch doesn't fix the colibri_t20 board, even though it has the same
issue, since Marcel already sent a patch for that.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Harmony and Ventana
USB ULPI PHY reset signals are typically active low. Consequently, they
should be marked as GPIO_ACTIVE_LOW in device tree, and indeed they are in
the Linux kernel DTs, and in DT properties that U-Boot doesn't yet use.
However, in DT properties that U-Boot does use, the value has been set to
0 (== GPIO_ACTIVE_HIGH) to work around a bug in U-Boot.
This change fixes the DT to correctly represent the HW, and fixes the
Tegra USB driver to cope with the fact that dm_gpio_set_value() internally
handles any inversions implied by the DT value GPIO_ACTIVE_LOW.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Implementations of the standard clock and reset APIs are available on all
Tegra SoCs now, so enable compilation of those uclasses.
Enable the Tegra CAR drivers for all SoCs prior to the BPMP being
available. This provides an implementation of those APIs everywhere.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Make clock_get_periph_rate() return the correct value for UART clocks.
This change needs to be applied before the patches that enable CONFIG_CLK
for Tegra SoCs before Tegra186, since enabling that option causes
ns16550_serial_ofdata_to_platdata() to rely on clk_get_rate() for UART
clocks, and clk_get_rate() eventually calls clock_get_periph_rate().
This change is a rather horrible hack, as explained in the comment added
to the clock driver. I've tried fixing this correctly for all clocks as
described in that comment, but there's too much fallout elsewhere. I
believe the clock driver has a number of bugs which all cancel each-other
out, and unravelling that chain is too complex at present. This change is
the smallest change that fixes clock_get_periph_rate() for UART clocks
while guaranteeing no change in behaviour for any other clock, which
avoids other regressions.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A future patch will implement a clock uclass driver for Tegra. That driver
will call into Tegra's existing clock code to simplify the transition;
this avoids tieing the clock uclass patches into significant refactoring
of the existing custom clock API implementation.
Some of the Tegra clock APIs that manipulate peripheral clocks require
both the peripheral clock ID and parent clock ID to be passed in together.
However, the clock uclass API does not require any such "parent"
parameter, so the clock driver must determine this information itself.
This patch implements new Tegra- specific clock API
clock_get_periph_parent() for this purpose.
The new API is implemented in the core Tegra clock code rather than SoC-
specific clock code. The implementation uses various SoC-/clock-specific
data. That data is only available in SoC-specific clock code.
Consequently, two new internal APIs are added that enable the core clock
code to retrieve this information from the SoC-specific clock code. Due to
the structure of the Tegra clock code, this leads to some unfortunate code
duplication. However, this situation predates this patch.
Ideally, future work will de-duplicate the Tegra clock code, and migrate
it into drivers/clk/tegra. However, such refactoring is kept separate from
this series.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Currently, Tegra peripheral drivers control two aspects of their HW module
clock(s):
1) The clock enable/rate for the peripheral clock itself.
2) The system-level clock tree setup, i.e. the clock parent.
Aspect 1 is reasonable, but aspect 2 is a system-level decision, not
something that an individual peripheral driver should in general know
about or influence. Such system-level knowledge ties the driver to a
specific SoC implementation, even when they use generic APIs for clock
manipulation, since they must have SoC-specific knowledge such as parent
clock IDs. Limited exceptions exist, such as where peripheral HW is
expected to dynamically switch between clock sources at run-time, such
as CPU clock scaling or display clock conflict management in a multi-head
scenario.
This patch enhances the Tegra core code to perform system-level clock
tree setup, in a similar fashion to the Linux kernel Tegra clock driver.
This will allow future patches to simplify peripheral drivers by removing
the clock parent setup logic.
This change is required prior to converting peripheral drivers to use the
standard clock APIs, since:
1) The clock uclass doesn't currently support a set_parent() operation.
Adding one is possible, but not necessary at the moment.
2) The clock APIs retrieve all clock IDs from device tree, and the DT
bindings for almost all peripherals only includes information about the
relevant peripheral clocks, and not any potential parent clocks.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* Brought in the correct Tegra210 CAR binding; the old file in U-Boot
appears to be a renamed version of the Tegra124 bindings rather than
the real Tegra210 version.
* Conversion of SPI and UART nodes to standard DMA bindings. U-Boot
doesn't use DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
information required by U-Boot, so U-Boot is not affected.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot, including separation of the
Tegra LIC (Legacy IRQ controller) and GIC.
* Node sort order fixes.
Remaining deltas relative to the Linux DT:
* U-Boot has enabled PCIe for Tegra210, but the kernel hasn't yet.
* The GPIO node compatible value in the kernel explicitly includes
Tegra124 values whereas U-Boot does not. I'll send a kernel patch to
correct this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* USB phy_type property is aligned with the kernel, so board files are
updated so the final DT content doesn't change. I'm not convinved that
Nyan uses HSIC phy_type. However, I'd rather this change be a no-op,
and any DT bug-fixes be separate.
* Sync misc changes from the kernel: missing DT content, minor compatible
value fixes, typos.
Remaining deltas relative to the Linux DT:
* U-Boot uses #address-cells/#size-cells of 1 whereas the kernel uses 2.
I believe U-Boot's DT parsing currently assumes that these values match
the physical address size, so I didn't synchronize this part of the DT.
* U-Boot uses the original XUSB PHY DT binding, wherease the kernel DT
has moved to a newer version. Thus, XUSB client nodes include properties
names phys and phy-names that do not appear in the kernel, and don't
include pad definitions in the padctl node.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* Conversion of SPI nodes to standard DMA bindings. U-Boot doesn't use
DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
information required by U-Boot, so U-Boot is not affected.
* Boards need to define the clk32k_in clock that feeds the Tegra PMC.
* Addition of tegra114-mc.h since tegra114.dtsi now includes it.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot.
* Node sort order fixes.
Remaining deltas relative to the Linux DT:
* USB node compatible values in U-Boot explicitly list Tegra114 values
whereas the kernel does not. I'll send a kernel patch to correct this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* Modification of PCIe memory region addresses. The HW memory layout is
programmable, so this should work fine, and Beaver PCIe was tested
without issue.
* Removal of pcie_xclk from the PCIe node and clock binding header. This
clock doesn't exist and isn't used; only a reset with this ID exists.
* Conversion of SPI nodes to standard DMA bindings. U-Boot doesn't use
DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
information required by U-Boot, so U-Boot is not affected.
* Changed the phy_type value for the second USB port. This required board
DTs to be updated to keep the same configuration.
* Boards need to define the clk32k_in clock that feeds the Tegra PMC.
* Addition of tegra30-mc.h since tegra30.dtsi now includes it.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot.
* Node sort order fixes.
Remaining deltas relative to the Linux DT:
* None.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This brings in a few minor fixes since the last sync. The largest change
is the removal of the definition for TEGRA20_CLK_PCIE_XCLK. This clock
doesn't actually exist.
Remaining deltas:
* Addition of u-boot,dm-pre-reloc property to a couple of nodes.
* Addition of the NAND controller, which Linux doesn't yet support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Apparently the unit address in a DT node name is now supposed to be a
single integer value, rather than a comma-separated list of individual
cell values. Fix the U-Boot DTs to comply with this naming convention.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Convert the Tegra MMC driver to DM_MMC. Support for non-DM is removed
to avoid ifdefs in the code. DM_MMC is now enabled for all Tegra builds.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
(swarren, fixed some NULL pointer dereferences, removed extraneous
changes, rebased on various other changes, removed non-DM support etc.)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Most other pin mux is configured in this function. This removes the
need to do it in an MMC-specific initialization function, which is good
since that function is going away later in this series.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
struct mmc_host is a Tegra-specific structure, but the name implies it's
something defined by core MMC code, which is confusing. Rename it to
struct tegra_mmc_priv to make its purpose more obvious. The new name is
also more appropriate for a DM driver private data structure, which will
be relevant later in this series.
Nothing needs access to this type except the MMC driver itself. Move the
definition into the driver C file.
Make sure all Tegra MMC functions are named tegra_mmc_*. Even though
they're all static, it's useful to have good naming so that symbol tables
are easy to interpret. A few functions aren't renamed by this patch since
they'll be deleted by a subsequent patch in this series.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
pad_init_mmc() is performing an SoC-specific operation, using registers
within the MMC controller. There's no reason to implement this code
outside the MMC driver, so move it inside the driver.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra MMC driver currently honors "sdhci" entries in /aliases. The
MMC core however uses "mmc" entries in /aliases. This difference will be
relevant once the Tegra MMC driver is converted to DM, and the MMC core
handles alias lookups. To avoid issues during that conversion, fix the
Tegra MMC driver and all Tegra DTs to use the same alias name as the MMC
core does.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
During debug of the DM_MMC changes to the Tegra MMC driver, I
noticed that the 'removable' property wasn't being set correctly
for the eMMC parts on most Tegra boards. Since the kernel DTS has
this property set correctly, it should be in U-Boot's Tegra DT too.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the COMPHY device tree nodes that are still missing to
the Armada 7K/8K dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
The clock frequency needs to be provided in the DT. Otherwise the driver
won't start in U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds basic support for the Marvell Armada 7K DB-88F7040
development board. Supported are the following interfaces:
- UART
- SPI (incl. SPI NOR)
- I2C
- USB
- SATA / AHCI
Support for other interfaces will follow.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Compared to the Armada 3700, the Armada 7K and 8K are much more on the
high-end side: they use a dual Cortex-A72 or a quad Cortex-A72, as
opposed to the Cortex-A53 for the Armada 3700.
The Armada 7K and 8K also use a fairly unique architecture, internally
they are composed of several components:
- One AP (Application Processor), which contains the processor itself
and a few core hardware blocks. The AP used in the Armada 7K and 8K
is called AP806, and is available in two configurations:
dual Cortex-A72 and quad Cortex-A72.
- One or two CP (Communication Processor), which contain most of the I/O
interfaces (SATA, PCIe, Ethernet, etc.). The 7K family chips have one
CP, while the 8K family chips integrate two CPs, providing two times
the number of I/O interfaces available in the CP.
The CP used in the 7K and 8K is called CP110.
All in all, this gives the following combinations:
- Armada 7020, which is a dual Cortex-A72 with one CP
- Armada 7040, which is a quad Cortex-A72 with one CP
- Armada 8020, which is a dual Cortex-A72 with two CPs
- Armada 8040, which is a quad Cortex-A72 with two CPs
This patch adds basic support for this ARMv8 based SoC into U-Boot.
Future patches will integrate other device drivers and board support,
starting with the Marvell DB-88F7040 development board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch integrates the Armada 7K/8K dts files from the latest
submission on the linux-arm-kernel mailing list.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds basic support for the Marvell Armada 3700 DB-88F3720
development board. Supported are the following interfaces:
- UART
- SPI (incl. SPI NOR)
- I2C
- Ethernet
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
The Armada 3700 integrates the following interfaces (not complete list):
- Dual Cortex-A53 ARMv8
- USB 3.0
- SATA 3.0
- PCIe 2.0
- 2 x Gigabit Ethernet 1Gbps / 2.5Gbps
- ...
This patch adds basic support for this ARMv8 based SoC into U-Boot.
Future patches will integrate other device drivers and board support
for the Marvell DB-88F3720 development board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds the USB device tree nodes that are still missing to
the Armada 3700 dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds the COMPHY device tree nodes that are still missing to
the Armada 3700 dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds the I2C device tree nodes that are still missing to
the Armada 3700 dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds the ethernet device tree nodes that are still missing to
the Armada 3700 dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds the SPI device tree nodes that are still missing to
the Armada 3700 dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This patch integrates the Armada 3700 dts files from the latest
submission on the linux-arm-kernel mailing list.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Instead of using CONFIG_* name space, rename these two macros to
SYS_FSL_* space.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this option to Kconfig and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this config to Kconfig option and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Calvin Johnson <calvin.johnson@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this option to Kconfig and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This board is a plug in card for Marvell's switch system development
kits. Form-factor aside it is similar to the DB-88F6820-GP with the
following differences.
- TCLK is 200MHz
- SPI1 is used
- No SATA
- No MMC
- NAND flash
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
88F6820 is a specific Armada-38x chip that is used on the DB-88F6820-GP
board. Rather than having DB_88F6820_GP and TARGET_DB_88F6820_GP which
selects the former. Rename DB_88F6820_GP to 88F6820 so that other boards
using the 88F6820 can be added.
Stefan:
Change 88F6820 for clearfog as well.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Unlike Linux, nothing about errno.h is arch-specific in U-Boot.
As you see, all of arch/${ARCH}/include/asm/errno.h is just a
wrapper of <asm-generic/errno.h>. Actually, U-Boot does not
export headers to user-space, so we just have to care about the
consistency in the U-Boot tree.
Now all of include directives for <asm/errno.h> are gone.
Deprecate <asm/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Initialize PLLs (SPL initializes only DPLL to save the precious
SPL memory footprint)
- Adjust CPLL/MPLL to the final tape-out frequency
- Set the Cortex-A53 clock to the maximum frequency since it is
running at 500MHz (SPLL/4) on startup
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As I repeated in the ML, I am unhappy with config entries with bare
defaults. Kick them out of arch/arm/mach-uniphier/Kconfig.
Currently, CONFIG_SPL_SERIAL_SUPPORT is not user-configurable
(build fails without it), but it should be fixed later anyway,
so I am moving CONFIG_SPL_SERIAL_SUPPORT to defconfigs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
driver/usb/dwc3/gadget.c need a "sys_proto.h" header file, add a
empty one to make compile success.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
lowlevel_init() is never needed for rk3288, so drop it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
rk3399 evb using one gpio to enable 5V output for both USB 2.0
host port, let's use fixed regulator for them.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
rk3399 has two dwc3 controller for type-C port, add the dts node
and enable them.
Signed-off-by: MengDongyang <daniel.meng@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Select DM_USB to compatible with USB DM driver model.
Signed-off-by: MengDongyang <daniel.meng@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
We do some SoC level one time setting initialization in
arch_cpu_init.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a condition to determine the rk3288_sdram_channel size.
This patch fixes read sdram_channel property failed from DT on rk3288
boards, which not enable OF_PLATDATA.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
This patch add pinctrl for sdcard which may not be initialized before
uboot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
pmugrf is a module like grf which contain some of the iomux registers
and other registers.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
It should be enough to call low(5us)->high pulse for all cases
to provide proper reset. There is no need to call high->low->high.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mode pins can be used as output for reset. Xilinx boards are using
this feature as additional way how to reset USB phys and also others
chips on the boards.
Mode1 is used on all these boards for this feature.
Let SPL toggle reset on this pin by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPL needs to have bigger stack size because of USB.
Simple malloc needs to be disabled because dfu code requires different
allocation functions. There is no space in OCM that's why random place
in DDR is used.
BOOTD must be disabled because it is causing compilation error.
All variables are disabled and used only variables valid for DFU because
they are simple huge. Including automatic variables added by
CONFIG_ENV_VARS_UBOOT_CONFIG.
Hardcode addresses for u-boot, atf, kernel and dtb
just for SPL DFU code.
Enable SPL DFU for zcu100.
Create new usb_dfu_spl variable just to run Linux kernel loaded in SPL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP provides an option to overwrite bootmode setting which
can change SPL behavior.
For example: boot SPL via JTAG and then SPL loads images from SD.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Import the latest version from the Diag software.
- Support LD21 SoC (including DDR chips in the package)
- Per-board granule adjustment for both reference and TV boards
- Misc cleanups
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Initialize the DPLL (PLL for DRAM) in SPL, and others in U-Boot
proper. Split the common code into pll-base-ld20.c for easier
re-use.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now PLLs for DRAM controller are initialized in SPL, and the others
in U-Boot proper. Setting up all of them in a single directory will
be helpful when we want to share code between SPL and U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The PLL for the DRAM interface must be initialized in SPL, but the
others can be delayed until U-Boot proper. Move them from SPL to
U-Boot proper to save the precious SPL memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is the last code in the mach-uniphier/pinctrl/ directory.
Push the remaining code out to delete the directory entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the pin-mux data in the pinctrl drivers by directly calling
pinctrl_generic_set_state().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This will be needed for setting up the System Bus pin-mux via the
LD11/LD20 pinctrl driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The NAND subsystem has not supported the Driver Model yet, but the
NAND pin-mux data are already in the pinctrl drivers. Use them by
calling pinctrl_generic_set_state() directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now all UniPhier SoCs support a pinctrl driver. Select (SPL_)PINCTRL
since it is mandatory even for base use.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The NanoPi NEO is a simple h3 board with 512MB RAM, ethernet, one usb
and one usb OTG connector.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Linux kernel musb driver expects VBUS to be off while initializing
musb. Having it on results in a repeating string of warnings, followed
by an unusable peripheral. The peripheral is only usable after
physically removing the OTG adapter, letting musb reset its state.
This partially reverts commit c9f8947e66 ("sunxi: usb-phy: Never
power off the usb ports")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
There are a few options which use lower case. We should use upper case for
all CONFIG options.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add usbtty/nand hunk to include/configs/spear3xx_evb.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
A few boards define this in a header file which is incorrect. It means that
Kconfig options that rely on this cannot be used. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
A few boards define this in a header file which is incorrect. It means that
Kconfig options that rely on this cannot be used. Move it.
Note that quite a few boards defined this options but do not appear to
actually use SPL:
BSC9132QDS_NOR_DDRCLK100_SECURE
BSC9132QDS_NOR_DDRCLK133_SECURE
BSC9132QDS_SDCARD_DDRCLK100_SECURE
BSC9132QDS_SDCARD_DDRCLK133_SECURE
BSC9132QDS_SPIFLASH_DDRCLK100_SECURE
BSC9132QDS_SPIFLASH_DDRCLK133_SECURE
C29XPCIE_NOR_SECBOOT
P1010RDB-PA_36BIT_NAND_SECBOOT
P1010RDB-PA_36BIT_SPIFLASH_SECBOOT
P1010RDB-PA_NAND_SECBOOT
P1010RDB-PA_NOR_SECBOOT
P1010RDB-PB_36BIT_NOR_SECBOOT
P1010RDB-PB_36BIT_SPIFLASH_SECBOOT
P1010RDB-PB_NAND_SECBOOT
P1010RDB-PB_NOR_SECBOOT
P3041DS_SECURE_BOOT
P4080DS_SECURE_BOOT
P5020DS_NAND_SECURE_BOOT
P5040DS_SECURE_BOOT
T1023RDB_SECURE_BOOT
T1024QDS_DDR4_SECURE_BOOT
T1024QDS_SECURE_BOOT
T1024RDB_SECURE_BOOT
T1040RDB_SECURE_BOOT
T1042D4RDB_SECURE_BOOT
T1042RDB_SECURE_BOOT
T2080QDS_SECURE_BOOT
T2080RDB_SECURE_BOOT
T4160QDS_SECURE_BOOT
T4240QDS_SECURE_BOOT
ls1021aqds_nor_SECURE_BOOT
ls1021atwr_nor_SECURE_BOOT
ls1043ardb_SECURE_BOOT
For these boards CONFIG_SPL_DM will no-longer be defined in SPL. But since
they apparently don't have an SPL, this should not matter.
Signed-off-by: Simon Glass <sjg@chromium.org>
The secure boot header files incorrectly define SPL options only if
CONFIG_SPL_BUILD is defined. This means that the options are only enabled
in an SPL build, and not with a normal 'make xxx_defconfig'. This means
that moveconfig.py cannot work, since it sees the options as disabled even
when they may be manually enabled in an SPL build.
Fix this by changing the order.
Signed-off-by: Simon Glass <sjg@chromium.org>
Unfortunately, this SoC needs per-board adjustment between clock
and address/command lines. This flag will be passed to the DRAM
init function and used for compensating the difference of DRAM
timing parameters.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
LS1046AQDS Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
SATA:
* SerDes2 Lane3 to SATA port
USB 3.0: one super speed USB 3.0 type A port
one Micro-AB port
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This is a workaround to fix SATA CRC error. Once the root cause
is found the ECC disabling will be removed.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable ERRATUM_A008511, ERRATUM_A009801, ERRATUM_A009803,
ERRATUM_A009942, ERRATUM_A010165
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As per the top level U-Boot README "Board Initialisation Flow"
section, board_init_f() should return without calling board_init_r()
directly. Clearing BSS and calling board_init_r() will be done in
crt0_64.S.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The CONFIG_STANDALONE_LOAD_ADDR is set to 0x80300000 by default.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
According to design specification, the L2 cache operates at the same
frequency as the A72 CPUs in the cluster with a 3-cycle latency, so
increase the L2 Data RAM and Tag RAM latency to 3 cycles, or else,
will run into different call trace issues.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This general MMDC driver adds basic support for Freescale MMDC
(Multi Mode DDR Controller). Currently MMDC is integrated on ARMv8
LS1012A SoC for DDR3L, there will be a update to this driver to
support more flexible configuration if new features (DDR4, multiple
controllers/chip selections, etc) are implimented in future.
Meantime, reuse common MMDC driver for LS1012ARDB/LS1012AQDS/
LS1012AFRDM.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The deep sleep function of LS1 platform, is mapped into PSCI system
suspend function, this patch adds implementation of it.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The EPU Finite State Machie (FSM) is used in both the last stage of
system suspend and the earliest stage of system resume.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds definitions of all the regesters necessary for
system sleep.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The v7_flush_dcache_all function will be called by ls102xa platform system
suspend, it is necessary to make it a public call instead of a local one, but
changing the LENTRY to ENTRY isn't enough, because there is another one using
the same name, so this one gets a psci_ prefix.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the access to serders protocol unselected PCIe controller will
hang. So disable the R/W permission to unselected PCIe controller
including its CCSR, IO space and memory space according to the
serders protocol field of RCW.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Move forward the basic non-secure access enable operation, so the
subsequent individual device access permission can override it.
And collect the dispersed callers in board level, and then move
them to SoC level.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Up to now, the function is_serdes_configed() doesn't check if the map
of serdes protocol is initialized before accessing it. The function
is_serdes_configed() will get wrong result when it was called before
the serdes protocol maps initialized. As the first element of the map
isn't used for any device, so use it as the flag to indicate if the
map has been initialized.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of Secure Boot Chain of trust, PPA image must be validated
before the image is started.
The code for the same has been added.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
DDR erratum A008336 only applies to DDR controller v5.2.0.
DDR controller v5.2.1 already has default 0x43b30002 in
EDDRTQCR1 register for optimal performance.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently, the UniPhier platform calls several init functions in the
following order:
[1] spl_board_init()
[2] board_early_init_f()
[3] board_init()
[4] board_early_init_r()
[5] board_late_init()
The serial console is not ready at the point of [2], so we want to
avoid using [2] from the view point of debuggability. Fortunately,
all of the initialization in [2] can be delayed until [3]. I see no
good reason to split into [3] and [4]. So, merge [2] through [4].
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We can use checkboard() stub to show additional board information,
so misc_init_f() should not be used for this purpose.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is the state-of-the-art MMC driver implementation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver has not been converted to Driver Model, and it is an
obstacle to migrate other block device drivers. Remove it for now.
The UniPhier SoCs already use a DM-based EHCI driver, so now
ARCH_UNIPHIER can select DM_USB.
These two changes must be done atomically because removing the
legacy driver causes a build error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
ARCH_UNIPHIER is having more and more select:s. Sort them in case
a select is accidentally duplicated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We are supposed to not add config entries with only "default y"
in board/SoC Kconfig files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Move this option to Kconfig and set its default value to 4; this
increases the number of supported CPUs for some boards.
It consumes 1KB memory per CPU for PSCI stack, but it should not
be a big deal, given the amount of memory used for the modern OSes.
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms
can select. Then, move CONFIG_ARMV7_PSCI, which is automatically
enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled.
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_ARMV7_NONSEC is enabled, the linker script requires
CONFIG_ARMV7_PSCI_NR_CPUS regardless of CONFIG_ARMV7_PSCI.
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
SPL_BUILD is not a CONFIG in Kconfig, so !SPL_BUILD is always true.
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On all TI platforms the ROM defines a "downloaded image" area at or near
the start of SRAM which is followed by a reserved area. As it is at
best bad form and at worst possibly harmful in corner cases to write in
this reserved area, we stop doing that by adding in the define
NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image
area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this.
At current we define the end of scratch space at 0x228 bytes past the
start of scratch space this this gives us a lot of room to grow. As
these scratch uses are non-optional today, all targets are modified to
respect this boundary.
Tested on OMAP4 Pandaboard, OMAP3 Beagle xM
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Weber <weber@corscience.de>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: "B, Ravi" <ravibabu@ti.com>
Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: "Kipisz, Steven" <s-kipisz2@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary options.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import DTS files and dt-bindings includes from Linux 4.8-rc1.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far we could only tell the gpio framework that a GPIO was mapped as input or
output, not as alternative function.
This patch adds support for determining whether a function is mapped as
alternative.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and
REFR fields of the MDREF register as 1 and 7, respectively for
DDR3 and 0 and 3 for LPDDR2.
Looking at the MDREF initialization done via DCD we see that
boards do need to initialize these fields differently:
$ git grep 0x021b0020 board/
board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800
board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800
So introduce a mechanism for users to be able to configure
REFSEL and REFR fields as needed.
Keep all the mx6 SPL users in their current REF_SEL and REFR values,
so no functional changes for the existing users.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Add support for Advantech DMS-BA16 board. The board is based on Advantech
BA16 module which has a i.MX6D processor. The board supports:
- FEC Ethernet
- USB Ports
- SDHC and MMC boot
- SPI NOR
- LVDS and HDMI display
Basic information about the module:
- Module manufacturer: Advantech
- CPU: Freescale ARM Cortex-A9 i.MX6D
- SPECS:
Up to 2GB Onboard DDR3 Memory;
Up to 16GB Onboard eMMC NAND Flash
Supports OpenGL ES 2.0 and OpenVG 1.1
HDMI, 24-bit LVDS
1x UART, 2x I2C, 8x GPIO,
4x Host USB 2.0 port, 1x USB OTG port,
1x micro SD (SDHC),1x SDIO, 1x SATA II,
1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: u-boot@lists.denx.de
Cc: sbabic@denx.de
With commit ceec08f50b, phy is connected to slave 0, but
changing the phy node was missed, fix it by populating the
phy node to proper cpsw slave node.
Fixes: ceec08f50b ("ARM: dts: dra72-evm: Add mode-gpios entry for mac node")
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.
The dts file is identical to the one submitted to the upstream kernel,
except that it has the pending patch to enable the ethernet controller
squashed in, as u-boot already has sun8i-emac support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds an emac node to the orangepi-2 dts (not yet merged upstream,
but in u-boot we already have emac support); fixes the alphetically
sorting of nodes in sun8i-h3-orangepi-plus.dts and disables some
usb controllers in sun8i-h3-orangepi-plus.dts which are only used
on the plus2e, as upstream has decided to do a separate dts files
for the plus2e.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sun8i-emac driver follows an old version of the proposed DT
bindings, where the EMAC clock and EPHY control register range is
listed directly, rather than through a syscon phandle.
Add back the syscon register range to avoid an invalid data access.
We should fix the driver once the Linux kernel bindings have been
finalized.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A33-OLinuXino is A33 development board designed by Olimex LTD.
It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.
It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a proper dts for the iNet D978 rev2 based A33 tablets.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Colorado TK1 SOM is a small form factor board similar to the
Jetson TK1. The main differences lie in the pinmux, and in that the
PCIe controller is set to use in 4lanes+1lane, rather than 2+2.
The pinmux header here was generated from a spreadsheet provided by
Colorado Engineering using the tegra-pinmux scripts. The spreadsheet
was converted from v09 to v11 by me.
Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The board ID EEPROM and board ID stickers on p2771-0000 will use a numeric
versioning scheme, with version numbers such as 000/100/200/300/400/500.
Within NVIDIA, these versions are also known as A00/A01/A02/A03/A04/B00.
However, that numbering scheme is not easily visible outside of NVIDIA,
and so does not make much sense to use. Convert U-Boot to use the readily
visible numeric scheme.
Also, it turns out that the current A02 DT actually applies to board
versions 000/100/200 (A00..A02). Consequently rename this to 000 not 200
so that all U-Boot builds are named after the first version of the HW they
support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The eMMC on sLD3 is assigned with dedicated pins (only multiplexed
with GPIO), so it shouldn't hurt to enable eMMC on SPL all the time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The revision of the original support card (rev 3.5, rev 3.6) fits in
the 8 bit width revision register. When it was extended in a weird
way, it was versioned in the format of "3.6.x" (where it should have
been "3.7", of course). What is worse, only the sub-level version
"6.x" was recorded in the 8 bit width register, completely ignoring
the compatibility of the revision register format.
This patch saves madly-versioned support cards by assuming the major
version "3" when the MSB 4 bit of the register is read as "6". With
this, the support card revision that were displayed as "6.10" is now
corrected to "3.6.10".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This supports the system reset via PSCI for ARMv7 SoCs.
Because the system reset is not supported on PSCI 0.1, let's define
CONFIG_ARMV7_PSCI_1_0. (it is supported since PSCI 0.2, but there
is no CONFIG to enable it in U-Boot for now.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The page table is maintained by the CPU, hence it is safe to always
align cache flush to a whole cache line size. This allows to use
mmu_page_table_flush for a single page table, e.g. when configure
only small regions through mmu_set_region_dcache_behaviour.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add LPAE support for mmu_set_region_dcache_behaviour. The function
is in use in some LPAE capable board such TI DRA7xx or NXP i.MX 7.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This series moves the CONFIG_SYS_CACHELINE_SIZE. First, in nearly all
cases we are mirroring the values used by the Linux Kernel here. Also,
so long as (and in this case, it is true) we implement flushes in hunks
that are no larger than the smallest implementation (and given that we
mirror the Linux Kernel, again we are fine) it is OK to align higher.
The biggest changes here are that we always use 64 bytes for CPU_V7 even
if for example the underlying core is only 32 bytes (this mirrors
Linux). Second, we say ARM64 uses 64 bytes not 128 (as found in the
Linux Kernel) as we do not need multi-platform support (to this degree)
and only the Cavium ThunderX 88xx series has a use for such large
alignment.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: "Pali Rohár" <pali.rohar@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Alison Wang <b18965@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Saksham Jain <saksham.jain@nxp.com>
Cc: Qianyu Gong <qianyu.gong@nxp.com>
Cc: Wang Dongsheng <dongsheng.wang@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@freescale.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: tang yuantian <Yuantian.Tang@freescale.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Anand Moon <linux.amoon@gmail.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: huang lin <hl@rock-chips.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Xu Ziyuan <xzy.xu@rock-chips.com>
Cc: "jk.kernel@gmail.com" <jk.kernel@gmail.com>
Cc: "Ariel D'Alessandro" <ariel@vanguardiasur.com.ar>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: "Andrew F. Davis" <afd@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Carlos Hernandez <ceh@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Cc: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Chin Liang See <clsee@altera.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
The H3 PLL5 used for DRAM barely manages to lock to the required
frequency before DRAM controller starts, sometimes leading to wrong
delay-line calibration results.
This patch changes the PLL tuning parameters to the same values as
boot0 used, which speeds up the locking and fixes the problem.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When the backlight's pwm input is connected to a pwm output of the SoC,
actually use pwm to drive the backlight.
The mean reason for doing this is to fix the backlight turning off
for aprox. 1 second while the kernel is booting. This is caused by
the kernel actually using pwm to drive the backlight, so that it
can dim the backlight. First the pwm driver loads and switches the
pinmux for the pin driving the backlight's pwm input to the pwm
controller. Then about 1s later the actual backlight driver loads
and tells the pwm driver to actually update the pwm settings, which
have a power-on-reset value of "off".
An additional advantage is that this allows us to initatiate the
backlight at 80%, which is the kernel default, avoiding a brightness
change while the kernel loads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed by: Peter Korsgaard <peter@korsgaard.com>
Add a defconfig and dts file for the Empire Electronix M712 tablet, this
is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on
the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Sync dts files with the current (Aug 18th 2016) state of Maxime's
linux/sunxi/for-next repo.
Note this commit also updates configs/MSI_Primo81_defconfig,
adding: "# CONFIG_REQUIRE_SERIAL_CONSOLE is not set", this is necessary
because the tablet does not have a reachable uart so the dts sync
drops its serial0 alias.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a defconfig and dts file for tablets using the generic inet-q972 PCB.
Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.
This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Ensure appropriate error messages are generated. Previously all errors
indicated that the serdes was already in use. Now appropriate error
messages are given.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The NAND interface on the Armada-38x series is similar to that on the
Armada-XP. The key difference is that the NAND ECC clock ratio is
provided via the DFX Server registers instead of the Core Clock.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The nvidia,bpmp property is left over from an old BPMP I2C binding, and
shouldn't be present. Remove it from the SoC DT file, and update the
I2C driver not to parse it; the value wasn't used for anything any more
anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra SDHCI binding dictates that the reseet name for the Tegra SDHCI
clock be "sdhci" not "sdmmc", and that the clock is accessed by index
rather than by name. Fix the Tegra186 DT and MMC driver to honor this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra I2C binding dictates that the clock name for the Tegra I2C clock
be "div-clk" not "i2c". Fix the Tegra186 DT and I2C driver to honor this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There is no reason to duplicate code for DRA7xx platforms as there
can be Rail grouping. The maximum voltage detection algorithm can still
be run on other platforms with no Rail grouping and does not harm as
it gives the same result.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
gpio_en field is introduced to detect if pmic is controlled by GPIO.
Make this field 0 on all TPS659* pmics available on DRA7/OMAP5 based platforms
and remove the #ifndefs.
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The bootz and booti commands rely on common functionality that is found
in common/bootm.c and common/bootm_os.c. They do not however rely on
the rest of cmd/bootm.c to be implemented so split them into their own
files. Have various Makefiles include the required infrastructure for
CONFIG_CMD_BOOT[IZ] as well as CONFIG_CMD_BOOTM. Move the declaration
of 'images' over to common/bootm.c.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
BLANCHE is development board based on R-Car V2H SoC (R8A7792)
This commit supports the following periherals:
- SCIF, Ethernet, QSPI, MMC
Signed-off-by: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Salvator-x is an entry level development board based on
R-Car H3 SoC (R8A7795). This commit supports SCIF only.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renesas R8A7795 is CPU with Cortex-a57.
This supports the basic register definition and GPIO and
framework of PFC.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The K2G EVM from TI has an SD card slot as
well as onboard eMMC for data storage.
Enable support for these.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
K2G SoC from TI has two MMC/SD controllers.
Add device tree data for these.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The firmware on TC2 needs to be configured appropriately before booting
in nonsec mode will work as expected, so test for this and fall back to
sec mode if required.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Bring in required device tree file and bindings from Linux.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to make these PIO4 definitions shared with AT91 PIO4
pinctrl driver, move them from the existing gpio driver to the
head file, and rephrase them.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch is referred to at91 clock driver of Linux, to make
the clock node descriptions in DT aligned with the Linux's.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The L4T kernel complains about a CSITE clock rate above 144MHz, presumably
because the HW is only characterized for a clock less than that. Adjust the
rate to 136MHz to avoid the warning and stay in spec.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
(swarren, re-wrote commit description)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Currently, ft_system_setup() is implemented by board*.c, which are a bit
of a dumping ground for a bunch of unrelated functionality, and separate
versions exist for pre-Tegra186 and Tegra186. Move the implementation into
a separate file to separate functionality, and allow sharing.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
p2771-0000 has a couple of PCIe ports; one physically x4 desktop PCI
connector (which may run at x2 electrically, depending on the board
version and configuration) and a x1 connection to the M.2 slot (which may
not be active, depending on the board version and configuration). This
change enables those.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now that clock and reset drivers exist for Tegra186, we can enable the SD
card controller. Now that a BPMP I2C driver exists for Tegra186, we can
communicate with the PMIC to enable power to the SD card. Hook up the DT
content and board code required to make the SD card work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 supports the new standard clock and reset APIs. Older Tegra SoCs
still use custom APIs. Enhance the Tegra MMC driver so that it can operate
with either set of APIs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In Tegra186, on-SoC reset signals are manipulated using IPC requests to
the BPMP (Boot and Power Management Processor). This change implements a
driver that does that. It is unconditionally selected by CONFIG_TEGRA186
since virtually any Tegra186 build of U-Boot will need the feature.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In Tegra186, on-SoC clocks are manipulated using IPC requests to the BPMP
(Boot and Power Management Processor). This change implements a driver
that does that. A tegra/ sub-directory is created to follow the existing
pattern. It is unconditionally selected by CONFIG_TEGRA186 since virtually
any Tegra186 build of U-Boot will need the feature.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra BPMP (Boot and Power Management Processor) is a separate
auxiliary CPU embedded into Tegra to perform power management work, and
controls related features such as clocks, resets, power domains, PMIC I2C
bus, etc. This driver provides the core low-level communication path by
which feature-specific drivers (such as clock) can make requests to the
BPMP. This driver is similar to an MFD driver in the Linux kernel. It is
unconditionally selected by CONFIG_TEGRA186 since virtually any Tegra186
build of U-Boot will need the feature.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Linux stopped the use of keyword 'boolean' in Kconfig.
Refer to commit 6341e62b212a2541efb0160c470e90bd226d5496 ("kconfig:
use bool instead of boolean for type definition attributes")
in Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a node for evm_3v3_sd using onboard PCF GPIO expander which feeds
on to mmc vdd.
Update mapping for vmmc-supply and vmmc_aux-supply.
evm_3v3_sd supplies to SD card vdd, and ldo1 to sdcard i/o lines.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Create drivers/sysreset and move sysreset-uclass and all sysreset
drivers there.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Flush operations need to be cacheline aligned to take effect, make
sure to flush always complete cachelines. This avoids messages such
as:
CACHE: Misaligned operation at range [00900000, 009004d9]
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
This outer cache allows to control active ways independently for
each CPU, so this function will be useful to set up active ways
for a specific CPU.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move this option to Kconfig, renaming it into CONFIG_CACHE_UNIPHIER.
The new option name makes sense enough, and the same as Linux has.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now, all of these macros are only used in cache-uniphier.c, so
there is no need to export them in a header file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DRAM is available at this point, so setup the temporary stack
and call the C function to reduce the code duplication a bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The System Cache (outer cache) is used not only as L2 cache,
but also as locked SRAM. The functions for turning on/off it
is necessary whether the L2 cache is enabled or not.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As the sLD3 Boot ROM has a complex page table, it is difficult to
set up the debug UART with enabling it. It will be much easier to
initialize the UART port after switching over to the straight-mapped
page table.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 4b50369fb5 ("ARM: uniphier: create early page table at
run-time") broke the ROM boot mode for PH1-sLD3 SoC, because the
run-time page table creation requires the outer cache register
access but the page table in the sLD3 Boot ROM does not straight-map
virtual/physical addresses.
The idea here is to check the current page table to determine if
it is a straight map table. If not, adjust the outer cache register
base.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Here, the ldr pseudo-instruction falls into the ldr + data set.
The register access by [r1, #offset] produces shorter code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_UNIPHIER_L2CACHE_ON is undefined, the L2 cache is never
enabled, so there is no need for v7_outer_cache_disable(). The weak
stub avoids the compile error anyway.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The UniPhier outer cache (L2 cache on ARMv7 SoCs) can be used as
SRAM by locking ways.
These functions will be used to transfer the trampoline code for SMP
into the locked SRAM.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Unify the range/all operation routines into the common function,
uniphier_cache_maint_common(), and sync code with Linux a bit more.
This reduces the code duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. This is controlled by pcf gpio line. Add
appropriate mode-gpios DT entry so that driver can select the required
slave.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
PCF8575 does not have any registers hence, offset field needs to be
ignored for i2c read/write. Therefore populate u-boot,i2c-offset-len
with 0 in PCF8575 DT nodes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We create 2 sets of page tables: One for normal operation, one for
emergency (used while modifying the former).
Because the page tables grow dynamically, we have code that checks
for overflow. Unfortunately we didn't adjust the available space
variable while creating the emergency tables, so potentially someone
might run into an overflow there (not seen in real world yet though!).
Fix it by properly adjusting the size as well as the base offset in
emergency page table creation.
Reported-by: York Sun <york.sun@nxp.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
These config targets were added well before the Kconfig migration began
as a way to demonstrate how to make these platforms work with cut down
features. At this point in time they no longer serve a good purpose so
remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
rk3399 sdcard is using dwmmc controller, enable it for sdcard.
SCLK_SDMMC is the clock for controller operation clock, move it
to the first place.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add an extra byte so that this data is not byteswapped.
Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable fastboot feature on rk3036, please refer to doc/README.rockchip
for more detailed usage.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the case of omap3 we have a number of platforms that are close to
exceeding SRAM limits, depending on compiler. Move to USE_TINY_PRINTF
to give them more room. OMAP4 will soon enough be in a similar place,
so enable that now.
Signed-off-by: Tom Rini <trini@konsulko.com>
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.
Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.
I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.
CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.
Fixes: 95ebc253e6 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of testing booting Linux kernels on Rockchip devices, it was
discovered by Ziyuan Xu and Sandy Patterson that we had multiple and for
some cases incomplete isb definitions. This was causing a failure to
boot of the Linux kernel.
In order to solve this problem as well as cover any corner cases that we
may also have had a number of changes are made in order to consolidate
things. First, <asm/barriers.h> now becomes the source of isb/dsb/dmb
definitions. This however introduces another complexity. Due to
needing to build SPL for 32bit tegra with -march=armv4 we need to borrow
the __LINUX_ARM_ARCH__ logic from the Linux Kernel in a more complete
form. Move this from arch/arm/lib/Makefile to arch/arm/Makefile and add
a comment about it. Now that we can always know what the target CPU is
capable off we can get always do the correct thing for the barrier. The
final part of this is that need to be consistent everywhere and call
isb()/dsb()/dmb() and NOT call ISB/DSB/DMB in some cases and the
function names in others.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Sandy Patterson <apatterson@sightlogix.com>
Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reported-by: Sandy Patterson <apatterson@sightlogix.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce tegra_board_init() and call it from board_init(). Tegra wil use
tegra_board_init() for board-specific initialization, and board_init() for
SoC-specific initialization.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 has 8 I2C controllers including BPMP I2C. This patch adds the
other 7 generic controllers to Tegra186's DT.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
(swarren, fixed DT node sort order, tweak patch description)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra186 PCIe DT content is almost identical to previous chips, except
that the:
- There are 3 ports instead of 2.
- Some physical addresses have moved.
- PHY programming is handled by firmware, so CCPLEX DTs don't need to
reference any PHY.
- The power domain is explicitly represented in DT. This change is
mandatory for Tegra186 since standard power domain APIs are used, and
should be made to the DT for older SoCs, although we get away without
doing so since U-Boot currently uses custom APIs that hard-code power
domain IDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This allows the BPMP I2C device to be instantiated, which makes it
available to other drivers and the user.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds the DT content that's needed to allow board DTs to enable use
of BPMP, clocks, resets, GPIOs, eMMC, and SD cards.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The DT binding for the Tegra186 HSP module apparently wasn't quite final
when I posted initial U-Boot support for it. Add the final DT binding doc
and adapt all code and DT files to match it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The PPA binary may be stored on QSPI flash instead of NOR.
So, deprecated CONFIG_SYS_LS_PPA_FW_IN_NOR in favour of
CONFIG_SYS_LS_PPA_FW_IN_XIP to prevent fragmentation of code
by addition of a new QSPI specific flag.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Appended the compatible strings of old version PSCI to the latest
version supported. And there are some psci functions' property must
be added to DT only for psci version 0.1, including cpu_on, cpu_off,
cpu_suspend, migrate.
Note, ARMv8 Secure Firmware Framework doesn't support PSCI ver 0.1.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Identify the PSCI node only by its name, so removed the code finding
it by compatible string.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch:
"dm: mmc: zynq: Convert zynq to use driver model for MMC"
(sha1: 329a449f2c)
added dependency on enabling some MMC options by default.
There are minimal ZynqMP configurations which require
only minimal configurations to be enabled to keep u-boot size
as lower as possible.
Move options to defconfig instead.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Serial driver is getting clk information via DT that's why
also clk node needs to have this flag.
Different behavior was introduced by:
"dm: Use dm_scan_fdt_dev() directly where possible"
(sha1: 911954859d)
where simple-bus driver starts to call dm_scan_fdt_dev() which has
additional logic around pre_reloc_only parameter which exclude
clk nodes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add new Kconfig option to disable arch_fixup_fdt() calls for cases where
U-Boot shouldn't update memory setup in DTB file.
One example of usage of this option is to boot OS with different memory
setup than U-Boot use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
With the recent bug fixes for the sun8i_emac driver all known issues
are resolved, so we can re-enable the driver.
While at it, also enable the emac on the Orange Pi One.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Jagan Teki <jteki@openedev.com>
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fennec is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes
on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access
to display pins, I2C, SPI, UART and GPIOs.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The 'evb-rk3288' is not a vendor name, change it to 'rockchip' which is
the real vendor name.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Boot Rom wouldn't initialize sdmmc while booting from eMMC. We need to
setup sdmmc gpio, otherwise we will hit an error below:
=>mmc info
blk_get_device: if_type=6, devnum=0: dwmmc@ff0c0000.blk, 6, 0
uclass_find_device_by_seq: 0 -1
uclass_find_device_by_seq: 0 0
- -1 -1
- -1 0
- found
uclass_find_device_by_seq: 0 1
- -1 -1
- -1 0
- not found
fdtdec_get_int_array: interrupts
get_prop_check_min_len: interrupts
Buswidth = 1, clock: 0
Buswidth = 1, clock: 400000
Sending CMD0
dwmci_send_cmd: Timeout on data busy
dwmci_send_cmd: Timeout on data busy
dwmci_send_cmd: Timeout on data busy
dwmci_send_cmd: Timeout on data busy
This reverts commit 6efeeea79c.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Add an extra byte so that this data is not byteswapped.
Signed-off-by: Ziyuan Xu <jk.kernel@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
The CONFIG_ROCKCHIP_COMMON and CONFIG_SPL_ROCKCHIP_COMMON are no use now,
remove them.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
AM571x and AM572x IDK have a spansion s25fl256s QSPI flash on the board
connected to TI QSPI over CS0. Hence, add QSPI and flash slave
DT nodes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
According to AM572x DM SPRS953A, QSPI max bus speed is 76.8MHz.
Therefore update the spi-max-frequency value of QSPI node for DRA74 and
DRA72 evm. This increase flash read speed by ~2MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, hence
update QSPI input clock divider value (DPLL_PER_HS13) to provide 76.8MHz
clock, so that driver can use the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This commit adds support for the Toradex Computer on Modules
Colibri iMX7S/iMX7D. The two modules/SoC's are very similar hence
can be easily supported by one board. The board code detects RAM
size at runtime which is one of the differences between the two
boards. The board also uses the UART's in DTE mode, hence making
use of the new DTE support via serial DM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
There is no need for introducing MX7_SEC, as there is the
CONFIG_ARMV7_BOOT_SEC_DEFAULT option for this purpose.
Switch to CONFIG_ARMV7_BOOT_SEC_DEFAULT and get rid of
MX7_SEC.
Tested by booting a 4.1.15 NXP kernel with mx7dsabresd_secure_defconfig
target.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Move zynq to the latest driver model support by enabling CONFIG_DM_MMC,
CONFIG_DM_MMC_OPS and CONFIG_BLK.
Signed-off-by: Simon Glass <sjg@chromium.org>
The sunxi ethernet address generation code looks for ethernet[0-3]
aliases to find ethernet controllers to generate MAC addresses for.
Without a valid address, the driver fails to register.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.
The upstream kernel devs have decided that they want a separate
dts for the PC Plus rather then sharing a single dts between the
regular PC and the PC Plus. So add a new orangepi_pc_plus_defconfig
to match.
The added dts file matches the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
MMU bit in SCTLR needs to be set explicitly after tables are
created. It isn't an issue for EL3 becuase this bit is already
set by early MMU setup. But for other exception levels this
bit was not set.
Signed-off-by: York Sun <york.sun@nxp.com>
LS1021 offers two secure OCRAM blocks for trustzone.
This patch moves all the secure text sections into the OCRAM.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch implements PSCI functions for ls102xa SoC following PSCI v1.0,
they are as the list:
psci_version,
psci_features,
psci_cpu_suspend,
psci_affinity_info,
psci_system_reset,
psci_system_off.
Tested on LS1021aQDS, LS1021aTWR.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The input parameter CPU ID needs to be validated before furher oprations such
as CPU_ON, this patch introduces the function to do this.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds all the PSCI v1.0 functions in to the common framework, with
all the functions returning "not implemented" by default, as a common framework
all the dummy functions are added here, it is up to every platform developer to
decide which version of PSCI and which functions to implement.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS1046A processor is built on the QorIQ LS series architecture
combining four ARM A72 processor cores with DPAA 1.0 support.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Mihai Bantea <mihai.bantea@freescale.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
New SoC LS1046A belongs to Freescale Chassis Generation 2 and
has two SerDes so we need to add this support in fsl_lsch2.
The SoC related SerDes 2 support will be added in SoC patch.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Both LS1012A and LS1043A belong to FSL_LSCH2 and share some common
configurations. So put the common define under FSL_LSCH2 to increase
readability.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support to detect Cortex-A72 core for printing it out.
The Initiator Version of A72 core should be 0x4.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for reading bootscript and bootscript header from SD. Also
renamed macros *_FLASH to *_DEVICE to represent SD alongwith NAND and
NOR flash.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Override jump_to_image_no_args function to include validation of
u-boot image using spl_validate_uboot before jumping to u-boot image.
Also define macros in SPL framework to enable crypto operations.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove Soc specific defines and use generic chasis specific defines
for USB controller base address mapping.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The register offset of i2c_sysc offset is not correct as per
omap5[1]/dra7[2] TRM, correct the offsets as per the
documentation.
[1] - http://www.ti.com/lit/pdf/swpu249
[2] - http://www.ti.com/lit/pdf/spruhz6
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The register offset of i2c_sysc offset is not correct as per
omap4 TRM [1], correct the offsets as per the documentation.
[1] - http://www.ti.com/lit/ug/swpu235ab/swpu235ab.pdf
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The ChromeOS kernel reads the RAM settings from PMU_SYS_REG2 and expects
the bootloader to store the necessary information there. We're using
the same register to pass the same information between the SPL and
U-Boot but in a slightly different format.
Change this to use the format expected by the Linux DMC driver so that
the system doesn't hang in Linux by misconfiguring the RAM.
This is almost the same as commit b5788dc ("rockchip: rk3288: correct
sdram setting") which was reverted in commit b525556 ("Revert "rockchip:
rk3288: correct sdram setting"") but parenthese have been added to apply
the mask correctly when reading the "bw" setting and a couple of minor
style issues have been fixed to keep check_patch.pl happy.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
RK3399 is a SoC from Rockchip with dual-core Cortex-A72
and quad-core Cortex-A53 CPU. It supports two USB3.0
type-C ports and two USB2.0 EHCI ports. Other interfaces
are very much like RK3288, the DRAM are 32bit width address
and support address from 0 to 4GB-128MB range.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
These files are from kernel upstream:
"649a371 Add linux-next specific files for 20160616"
with some modification need by U-Boot:
- chosen with stdout-path to uart2.
- add clock-frequency for uart2
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The current code picks the first available clock. In U-Boot proper this is
the oscillator device, not the SoC clock device. As a result the HDMI display
does not work.
Fix this by calling rockchip_get_clk() instead.
Fixes: 135aa950 (clk: convert API to match reset/mailbox style)
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
On Rockchip SoCs we typically have a main clock device that uses the Soc
clock driver. There is also a fixed clock for the oscillator. Add a function
to obtain the core clock.
Signed-off-by: Simon Glass <sjg@chromium.org>
The function is very specific to the rk3288 in its arguments
referencing the rk3288 cru and grf and every other rockchip soc
has differing cru and grf registers. So make that function naming
explicit.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Having some sort of ordering proofed helpful in a lot of other places
already. So for a larger number of rockchip socs it might be helpful
as well instead of an ever increasing unsorted list.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
Enable fastboot feature on rk3288.
This path doesn't support the fastboot flash function command entirely.
We will hit "cannot find partition" assertion without specified
partition environment. Define gpt partition layout in specified board
such as firefly-rk3288, then enjoy it!
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
It conflicts with the generic_timer.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
In preparation for RK3368 and RK3399, which need to select ARM64, don't
select CPU_V7 at the ARCH_ROCKCHIP level but at the SoC level instead.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
The 'evb_rk3036' and 'kylin' is not a vendor name, let's replace them
to 'rockchip' which is a real _vendor_ name, and meet the architecure
'board/<vendor>/<board-name>/'.
More boards from rockchip like evb_rk3288, evb_rk3399 will comes later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.kernel@gmail.com>
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).
evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If we would like to boot from SD card, we have to implement mmc driver
in SPL stage, and get a slightly large SPL binary. Rockchip SoC's
bootrom code has the ability to load spl and u-boot, then boot.
If CONFIG_ROCKCHIP_SPL_BACK_TO_BROM is enabled, the spl will return to
bootrom in board_init_f(), then bootrom loads u-boot binary.
Loading sequence after rework:
bootrom ==> spl ==> bootrom ==> u-boot
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed up spelling of U-Boot, boorom, opinion->option, Rochchip:
Signed-off-by: Simon Glass <sjg@chromium.org>
A couple of commits have modified the am33xx/am437x ddr2/ddr3
initialization path to fix certain issues, but have had the side effect
of causing L3 noc errors during initialization. The two commits are:
69b918 "am33xx,ddr3: fix ddr3 sdram configuration"
fc46ba "arm: am437x: Enable hardware leveling for EMIF"
The EMIF_REG_INITREF_DIS_MASK bit still needs to be set for all
platforms. This delays initialization and refresh until a later stage.
The 500us timer can be programmed for platforms that require it
and for platforms that don't require it. It is currently hardcoded
for 400MHz systems. For systems with a higher memory frequency
this needs to be a larger value, and for systems with a lower
memory frequency this can be a lower value. This can be
considered a separate issue and corrected in a later commit.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The delay needs to be before the write to ref_ctrl register
which initiates refreshes. An improper initialization sequence
generates an L3 noc error.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
commit 1f807a9f32 ("ARM: keystone2: Refactor MSMC macros to avoid
left under a macro KS2_MSMC_SEGMENT_QM_PDSP which is no longer valid.
This, in effect disabled DMA coherency for QM PDSP.
Given that msmc_k2hkle_common_setup is valid for all K2H/K/L/E SoCs,
the #ifdef should been removed in the first place. Do the same.
Fixes: 1f807a9f32 ("ARM: keystone2: Refactor MSMC macros to avoid #ifdeffery")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the NAND controller in the sun5i-r8-chip.dts.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add the NAND controller definition to sun5i.dtsi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We need some macros to manipulate the NAND controller clock.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Deassert resets and enable clock signals of xHCI blocks if the
corresponding CONFIG is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I need to add more board attributes, so the "flags" member will be
handier than separate boolean ones.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Sync register macros with Linux code. This will be helpful to
develop the counterpart of Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This does not have much impact on behavior, but makes code look more
more like Linux. The use of devm_ioremap() often helps to delete
.remove callbacks entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On these two boards, the serial0 is used for inter-chip connection,
so cannot be used for login console. The serial2 is used instead
for them, but it is tedious to use because upper level deployment
projects must switch login console per board.
[ Linux commit: 2a4a2aadbaad9dffdb564a2895348f3d8e825416 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 17c2987 introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM57xx and DRA7xx high-security (HS) devices that
causes the build to break when that option is not active. Fix this issue
by only building the u-boot_HS.img target when building U-Boot into an
actual FIT image.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit e29878f introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM43xx high-security (HS) devices that causes the
build to break when that option is not active. Fix this issue by only
building the u-boot_HS.img target when building U-Boot into an actual
FIT image.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As part of the startup process for boards using the SPL, the
meaning of board_init_f changed such that it should return normally
rather than calling board_init_r directly. (see
db910353a1 )
This was fixed in 32-bit arm, but broke when SPL was added to
64 bit arm. This fixes crt0_64 so that it calls board_init_r
during the SPL and removes the direct call from board_init_f
from the arm SPL example.
Signed-off-by: Jeremy Hunt <Jeremy.Hunt@DEShawResearch.com>
Acked-by: Simon Glass <sjg@chromium.org>
identify_nand_chip hangs forever in loop when NAND is not present.
As IGEPv2 comes either with NAND or OneNAND flash, add reset timeout
to let function fail gracefully allowing caller to know NAND is
not present. On NAND equipped board, reset succeeds on first read,
so 1000 loops seems to be safe timeout.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Other payload than uImage is currently considered to be raw U-Boot
image. Check also for zImage in Falcon mode.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Make code 64bit aware.
Warnings:
+../arch/arm/lib/spl.c: In function ‘jump_to_image_linux’:
+../arch/arm/lib/spl.c:63:3: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
+../common/spl/spl_fat.c: In function ‘spl_load_image_fat’:
+../common/spl/spl_fat.c:91:33: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Per Vikas' request, the problem this commit is supposed to be solving is
something he doesn't see and further this introduces additional hardware
requirements.
This reverts commit 4b2fd720a7.
Signed-off-by: Tom Rini <trini@konsulko.com>
On Tegra186, U-Boot is booted by the binary firmware as if it were a
Linux kernel. Consequently, a DTB is passed to U-Boot. Cache the address
of that DTB, and parse the /memory/reg property to determine the actual
RAM regions that U-Boot and subsequent EL2/EL1 SW may actually use.
Given the binary FW passes a DTB to U-Boot, I anticipate the suggestion
that U-Boot use that DTB as its control DTB. I don't believe that would
work well, so I do not plan to put any effort into this. By default the
FW-supplied DTB is the L4T kernel's DTB, which uses non-upstreamed DT
bindings. U-Boot aims to use only upstreamed DT bindings, or as close as
it can get. Replacing this DTB with a DTB using upstream bindings is
physically quite easy; simply replace the content of one of the GPT
partitions on the eMMC. However, the binary FW at least partially relies
on the existence/content of some nodes in the DTB, and that requires the
DTB to be written according to downstream bindings. Equally, if U-Boot
continues to use appended DTBs built from its own source tree, as it does
for all other Tegra platforms, development and deployment is much easier.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Implement a hook to allow boards to save boot-time CPU state for later
use. When U-Boot is chain-loaded by another bootloader, CPU registers may
contain useful information such as system configuration information. This
feature mirrors the equivalent ARMv7 feature.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
IVC (Inter-VM Communication) protocol is a Tegra-specific IPC (Inter
Processor Communication) framework. Within the context of U-Boot, it is
typically used for communication between the main CPU and various
auxiliary processors. In particular, it will be used to communicate with
the BPMP (Boot and Power Management Processor) on Tegra186 in order to
manipulate clocks and reset signals.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Many files in arch/arm/mach-tegra are compiled conditionally based on
Kconfig variables, or applicable to all platforms. We can let the main
Tegra Makefile handle compiling (or not) those files to avoid each SoC-
specific Makefile needing to duplicate entries for those files. This
leaves the SoC-specific Makefiles to compile truly SoC-specific code.
In the future, we'll hopefully add Kconfig variables for all the other
files, and refactor those files, and so reduce the need for SoC-specific
Makefiles and/or ifdefs in the Makefiles.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There are multiple versions of p2771-0000 board. There are SW visible
incompatible differences between the versions, and they are relevant to
U-Boot. Create separate "A02" and "B00" defconfigs (named after the first
and/or only board rev the defconfig supports) so that users can select
which build they want.
With the minimal set of HW currently enabled in U-Boot, the differences
are irrelevant, hence the DT files aren't different. However, that will
change in a future patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 uses different GPIO port IDs compared to previous chips. Make
sure the SoC DT file includes the correct GPIO binding header.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit c1ebf54868 ("imx_common: Return MMCSD_MODE_FS in spl_boot_mode()
also for EXTFS") causes SPL breakage on wandboard:
ERROR: v7_dcache_inval_range - start address is not aligned - 0x1820006c
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1820086c
ERROR: v7_dcache_inval_range - start address is not aligned - 0x1820006c
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1820086c
** First descriptor is NOT a primary desc on 0:1 **
spl: no partition table found
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This error is seen when SPL and u-boot.img are stored in the raw SD card
partition.
This reverts commit c1ebf54868.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
According to the IMX6DQRM Reference Manual, the description
of bit 7 (axi_alt_sel) of the CCM_CBCDR register is:
"AXI alternative clock select
0 pll2 396MHz PFD will be selected as alternative clock for AXI root clock
1 pll3 540MHz PFD will be selected as alternative clock for AXI root clock "
The current logic is inverted, so fix it to match the reference manual.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Set the enable-method in the cpu node to PSCI, and create device
node for PSCI, when PSCI was enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
If the PSCI and PPA is ready, skip the fixup for spin-table and
waking secondary cores. Otherwise, change SMP method to spin-table,
and the device node of PSCI will be removed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The FSL Primary Protected Application (PPA) is a software component
loaded during boot which runs in TrustZone and remains resident
after boot.
Use the secure firmware framework to integrate FSL PPA into U-Boot.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This framework is introduced for ARMv8 secure monitor mode firmware.
The main functions of the framework are, on EL3, verify the firmware,
load it to the secure memory and jump into it, and while it returned
to U-Boot, do some necessary setups at the 'target exception level'
that is determined by the respective secure firmware.
So far, the framework support only FIT format image, and need to define
the name of which config node should be used in 'configurations' and
the name of property for the raw secure firmware image in that config.
The FIT image should be stored in Byte accessing memory, such as NOR
Flash, or else it should be copied to main memory to use this framework.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This function assume that the d-cache and MMU has been enabled earlier,
so it just created MMU table in main memory. But the assumption is not
always correct, for example, the early setup is done in EL3, while
enable_caches() is called when the PE has turned into another EL.
Define the function mmu_setup() for fsl-layerscape to cover the weak
one.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Drop platform code to create static MMU tables. Use common framework
to create MMU tables on the run. Tested on LS2080ARDB with secure and
non-secure ram scenarios.
Signed-off-by: York Sun <york.sun@nxp.com>
Use existing Kconfig symbols to let the user configure whether to
build a U-Boot with non-secure mode support or not. This also allows
to enable virtualization extension easily.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This can be useful if the same U-Boot binary is used for boards
available with a i.MX 7Solo and i.MX 7Dual.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce virtual and physical addresses in the mapping table. This change
have no impact on existing boards because they all use idential mapping.
Signed-off-by: York Sun <york.sun@nxp.com>
When page tables are created, allow later table to be created on
previous block entry. Splitting block feature is already working
with current code. This patch only rearranges the code order and
adds one condition to call split_block().
Signed-off-by: York Sun <york.sun@nxp.com>
Make setup_pgtages() and get_tcr() available for platform code to
customize MMU tables.
Remove unintentional call of create_table().
Signed-off-by: York Sun <york.sun@nxp.com>
When secure ram is used, MMU tables have to be put into secure ram.
To use common MMU code, gd->arch.tlb_addr will be used to host TLB
entry pointer. To save allocated memory for later use, tlb_allocated
variable is added to global data structure.
Signed-off-by: York Sun <york.sun@nxp.com>
Secure_ram variable was put in generic global data. But only ARMv8
uses this variable. Move it to ARM specific data structure.
Signed-off-by: York Sun <york.sun@nxp.com>
Now that we have a secure data section for storing variables, there
should be no need for platform code to get the stack address.
Make psci_get_cpu_stack_top a local function, as it should only be
used in armv7/psci.S and only by psci_stack_setup.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we have a secure data section and space to store per-CPU target
PC address, switch to it instead of storing the target PC on the stack.
Also save clobbered r4-r7 registers on the stack and restore them on
return in psci_cpu_on for Tegra, i.MX7, and LS102xA platforms.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we have a data section, add helper functions to save and fetch
per-CPU target PC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The secure monitor may need to store global or static values within the
secure section of memory, such as target PC or CPU power status.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi and i.mx7 both define the __secure modifier to put functions in
the secure section. Move this to a common place.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
As the PSCI implementation grows, we might exceed the size of the secure
memory that holds the firmware.
Add a configurable CONFIG_ARMV7_SECURE_MAX_SIZE so platforms can define
how much secure memory is available. The linker then checks the size of
the whole secure section against this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
psci_text_end was used to calculate the PSCI stack address following the
secure monitor text. Now that we have an explicit secure stack section,
this is no longer used.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we have a secure stack section that guarantees usable memory,
allocate the PSCI stacks in that section.
Also add a diagram detailing how the stacks are placed in memory.
Reserved space for the target PC remains unchanged. This should be
moved to global variables within a secure data section in the future.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Until now we've been using memory beyond psci_text_end as stack space
for the secure monitor or PSCI implementation, even if space was not
allocated for it.
This was partially fixed in ("ARM: allocate extra space for PSCI stack
in secure section during link phase"). However, calculating stack space
from psci_text_end in one place, while allocating the space in another
is error prone.
This patch adds a separate empty secure stack section, with space for
CONFIG_ARMV7_PSCI_NR_CPUS stacks, each 1 KB. There's also
__secure_stack_start and __secure_stack_end symbols. The linker script
handles calculating the correct VMAs for the stack section. For
platforms that relocate/copy the secure monitor before using it, the
space is not allocated in the executable, saving space.
For platforms that do not define CONFIG_ARMV7_PSCI_NR_CPUS, a whole page
of stack space for 4 CPUs is allocated, matching the previous behavior.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Targets that define CONFIG_ARMV7_SECURE_BASE will copy the secure section
to another address before execution.
Since the secure section in the u-boot image is only storage, there's
no reason to page align it and increase the binary image size.
Page align the secure section only when CONFIG_ARMV7_SECURE_BASE is not
defined. And instead of just aligning the __secure_start symbol, align
the whole .__secure_start section. This also makes the section empty,
so we need to add KEEP() to the input entry to prevent the section from
being garbage collected.
Also use ld constant "COMMONPAGESIZE" instead of hardcoded page size.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch finishes the rewrite of sunxi specific PSCI parts into C
code.
The assembly-only stack setup code has been factored out into a common
function for ARMv7. The GIC setup code can be renamed as psci_arch_init.
And we can use an empty stub function for psci_text_end.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Every platform has the same stack setup code in assembly as part of
psci_arch_init.
Move this out into a common separate function, psci_stack_setup, for
all platforms. This will allow us to move the remaining parts of
psci_arch_init into C code, or drop it entirely.
Also provide a stub no-op psci_arch_init for platforms that don't need
their own specific setup code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This enables extra USB controllers which enable use of the 3rd USB
port on the new Orange Pi Plus 2E variant.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that we know that the BROM stores a value indicating the boot-source
at the beginning of SRAM, use that instead of trying to recreate the
BROM's boot probing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch add EMAC driver support for H3/A83T/A64 SoCs.
Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY).
BIG Thanks to Andre for providing some of the DT code.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The patch converts one of the "reserved" fields in the sunxi SPL
header to a fel_uEnv_length entry. When booting over USB ("FEL
mode"), this enables the sunxi-fel utility to pass the string
length of uEnv.txt compatible data; at the same time requesting
that this data be imported into the U-Boot environment.
If parse_spl_header() in the sunxi board.c encounters a non-zero
value in this header field, it will therefore call himport_r() to
merge the string (lines) passed via FEL into the default settings.
Environment vars can be changed this way even before U-Boot will
attempt to autoboot - specifically, this also allows overriding
"bootcmd".
With fel_script_addr set and a zero fel_uEnv_length, U-Boot is
safe to assume that data in .scr format (a mkimage-type script)
was passed at fel_script_addr, and will handle it using the
existing mechanism ("bootcmd_fel").
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:
https://linux-sunxi.org/Bootable_SPI_flash
This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.
While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.
Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)
Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:
sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin
The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for of-platdata with rk3288 SDRAM initr. This requires decoding
the of-platdata struct and setting up the device from that. Also the driver
needs to be renamed to match the string that of-platdata will search for.
The platform data is copied from the of-platdata structure to the one used
by the driver. This allows the same code to be used with device tree and
of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is more correct to avoid touching the device tree in the probe() method.
Update the driver to work this way. Note that only SPL needs to fiddle with
the SDRAM registers, so decoding the platform data fully is not necessary in
U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
The syscon devices all end up having diffent driver names with of-platdata,
since the driver name comes from the first string in the compatible list.
Add separate device declarations for each one, and add a bind method to set
up driver_data correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an extra byte so that this data is not byteswapped. Add a comment to
the code to explain the purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present armv7 will unhappily invalidate a cache region and print an
error message. Make it skip the operation instead, as it does with other
cache operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Errata i727 is applicable on all OMAP5 and DRA7 variants but enabled only
on OMAP5 ES1.0. So, enable it on all platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This change is to remove a halt at about 200KiB
while sending a large(1MiB) binary to a micro controller using USART1.
USART1 is connected to a PC via an on-board ST-Link debugger
that also functions as a USB-Serial converter.
However, it seems to loss some data occasionally.
So I changed the serial port to USART6 and connected it to the PC using
an FTDI USB-Serial cable, therefore the transmission was successfully
completed.
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
This patch adds SDRAM support for stm32f746 discovery board.
This patch depends on previous patch.
This patch is based on STM32F4 and emcraft's[1].
[1]: https://github.com/EmcraftSystems/u-boot
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
This patch adds 200MHz clock configuration for stm32f746 discovery board.
This patch is based on STM32F4 and emcraft's[1].
[1]: https://github.com/EmcraftSystems/u-boot
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
These defines are valid only when iomem_valid_addr is defined,
but I do not see such defines anywhere. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, this is only defined in arch/arm/include/asm/types.h,
so move it to include/linux/types.h to make it available for all
architectures.
I defined it with phys_addr_t as Linux does. I needed to surround
the define with #ifdef __KERNEL__ ... #endif to avoid build errors
in tools building. (Host tools should not include <linux/types.h>
in the first place, but this is already messy in U-Boot...)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Modify the SPL build procedure for AM437x high-security (HS) device
variants to create a secure u-boot_HS.img FIT blob that contains U-Boot
and DTB artifacts signed (and optionally encrypted) with a TI-specific
process based on the CONFIG_TI_SECURE_DEVICE config option and the
externally-provided image signing tool.
Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.
Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds commands so that when a secure device is in use and the SPL is
built to load a FIT image (with combined U-Boot binary and various
DTBs), these components that get fed into the FIT are all processed to
be signed/encrypted/etc. as per the operations performed by the
secure-binary-image.sh script of the TI SECDEV package. Furthermore,
perform minor comments cleanup to make better use of the available
space.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds an API that verifies a signature attached to an image (binary
blob). This API is basically a entry to a secure ROM service provided by
the device and accessed via an SMC call, using a particular calling
convention.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds a generic C-callable API for making secure ROM calls on OMAP and
OMAP-compatible devices. This API provides the important function of
flushing the ROM call arguments to memory from the cache, so that the
secure world will have a coherent view of those arguments. Then is
simply calls the omap_smc_sec routine.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add an interface for calling secure ROM APIs across a range of OMAP and
OMAP compatible high-security (HS) device variants. While at it, also
perform minor cleanup/alignment without any change in functionality.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds missing flush_dcache_range and invalidate_dcache_range dummy
(empty) placeholder functions to the #else portion of the #ifndef
CONFIG_SYS_DCACHE_OFF, where full implementations of these functions
are defined.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are two enable methods supported by ARM64 Linux; psci and
spin-table. The latter is simpler and helpful for quick SoC bring
up. My main motivation for this patch is to improve the spin-table
support, which allows us to boot an ARMv8 system without the ARM
Trusted Firmware.
Currently, we have multi-entry code in arch/arm/cpu/armv8/start.S
and the spin-table is supported in a really ad-hoc way, and I see
some problems:
- We must hard-code CPU_RELEASE_ADDR so that it matches the
"cpu-release-addr" property in the DT that comes from the
kernel tree.
- The Documentation/arm64/booting.txt in Linux requires that
the release address must be zero-initialized, but it is not
cared by the common code in U-Boot. We must do it in a board
function.
- There is no systematic way to protect the spin-table code from
the kernel. We are supposed to do it in a board specific manner,
but it is difficult to predict where the spin-table code will be
located after the relocation. So, it also makes difficult to
hard-code /memreserve/ in the DT of the kernel.
So, here is a patch to solve those problems; the DT is run-time
modified to reserve the spin-table code (+ cpu-release-addr).
Also, the "cpu-release-addr" property is set to an appropriate
address after the relocation, which means we no longer need the
hard-coded CPU_RELEASE_ADDR.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Upon further review this breaks most other platforms as we need to check
what core we're running on before touching it at all.
This reverts commit d73718f323.
Signed-off-by: Tom Rini <trini@konsulko.com>
if we build for an i.mx6 (d)ual(l)ite CONFIC_MX6DL we shall use
MX6DL_PAD instead the common MX6_PAD.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
MX7_SEC is an existing configuration option that allows booting the
kernel in secure mode.
Place this option in Kconfig, so that boards can select this option
in their defconfig files.
Selecting this option is necessary when booting a kernel provided by
NXP, such as 3.14_GA and 4.1.15_GA.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Michael Trimarchi <michael@amarulasolutions.com>
Custom Board based on MX6 Dual, 1GB RAM and eMMC.
There are two variants of the board with and without
PCIe (ZC5202 and ZC5601).
Signed-off-by: Stefano Babic <sbabic@denx.de>
spl_boot_mode() returned MMCSD_MODE_RAW on MMC if CONFIG_SPL_EXT_SUPPORT
was configured. EXTFS is the default filesystem selected in imx6_spl.h
and the function should return MMCSD_MODE_FS instead.
Fix this and return MMCSD_MODE_FS instead in such cases.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
CC: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
This function have maintained for supporting Non-FDT.
Now, Almost all SoC are changed to fdt style.
So there are no that this function is called anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
It's correct to use '/' as prefix for aliases nodes.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rockchip uses driver model for all subsystems. Specify this in the arm
Kconfig rather than as defaults in the Rockchip Kconfig. This means that
boards cannot turn these options off, which seems correct.
Signed-off-by: Simon Glass <sjg@chromium.org>
According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better
throughput.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
K2G SoC has a Cadence QSPI controller to communicate with NOR flash
devices. Add DT nodes to support the same.
Also, K2G EVM has a s25fl512s flash connect to QSPI bus at CS 0. Add nor
flash slave node for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
K2G SoC has 4 SPI instances that are compatible with davinci_spi
controller(present on previous generation of Keystone2 devices). Add DT
nodes for the same. K2G EVM has a N25Q128A13 SPI NOR flash connected on
SPI-1. Add DT bindings for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add aliases for SPI nodes in order for it to be probed by the DM
framework.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
For A53, data coherency is enabled only when the CPUECTLR.SMPEN bit is
set. The SMPEN bit should be set before enabling the data cache.
If not enabled, the cache is not coherent with other cores and
data corruption could occur.
For A57/A72, SMPEN bit enables the processor to receive instruction
cache and TLB maintenance operations broadcast from other processors
in the cluster. This bit should be set before enabling the caches and
MMU, or performing any cache and TLB maintenance operations.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit e677724 (arm: Fix setjmp) added code to fix compilation of the setjmp
code path with thumv1. Unfortunately it missed a constraint that the adr
instruction can only refer to 4 byte aligned offsets.
So this patch adds the required alignment hooks to make compilation
work again even when setjmp doesn't happen to be 4 byte aligned.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Tom Rini <trini@konsulko.com>
We have standard drivers for panels and backlights which can do most of the
work for us. Move the tegra20 LCD driver over to use those instead of custom
code.
This patch includes device tree changes for the nvidia boards. I have only
been able to test seaboard. If this patch is applied, these boards will
also need to be synced with the kernel, and updated to use display-timings:
- colibri
- medcom-wide
- paz00
- tec
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Sync everything except the display panel, which will come in a future patch.
One USB port is left disabled since we don't want to support it in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
The DTS file is identical to the one submitted to the upstream kernel.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit b19236fd1 ("sunxi: Increase SPL header size to 64 bytes to avoid
code corruption") Added defines for MMC0 and SPI as boot identification.
After verifying on an OLinuXino Lime2 with NAND and eMMC, the expected
values have been confirmed and added to spl.h
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
I will carry this work-around until it is cared in the kernel.
This looks up the AIDET node and sets up a register to handle
active low interrupt signals.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The AIDET (ARM Interrupt Detector Add-on Circuit) is a kind of
syscon block related with the interrupt controller.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently layescape SoCs are not using cpu nodes. So removing
them in favour of compatibly with similar SoCs that
have different cores like LS2080A and LS2088A.
This has been tested on LS2080AQDS, LS1043ARDB, LS1012ARDB.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Freescale ARMv8 SoC name ends with "A" to represent ARM SoCs.
like LS2080A, LS1043A, LS1012A.
So append "A" to SoC names.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
add DM and DTS support for the at91 based siemens
boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Add this files from Linux v4.6-rc5
66b8a424d: [workqueue: fix ghost PENDING flag while doing MQ IO]
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Andreas Bießmann <andreas@biessmann.org>
Since the spl_boot_mode() is now passed the boot device to boot from,
make use of it instead of inquiring for the boot device again. This
allows board_boot_order() to function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
The handling of the "usage counter" is incorrect, and the clock should
only be disabled when transitioning from 1 to 0.
Reported-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
The Kona Peripheral Slave CCU has 4 policy mask registers, not 8.
Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Match the #ifdef ... #endif and the code,
ret = do_something();
if (ret)
return ret;
This will make it easier to add more #ifdef'ed code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
gic_kick_secondary_cpus can directly return to the caller of
smp_kick_all_cpus. We do not have to use x29 register here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
s/hardkernel/amlogic/ to have a single place for all the amlogic-based
boards.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
The register CLKCNCSR controls the frequency of all cores in the same
cluster.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
DISTRO_DEFAULTS is intended to mirror / replace
include/config_distro_defaults.h.
The intend is for boards which include this file to select this from
their Kconfig files and when moving setting to Kconfig which are #define-ed
in config_distro_defaults.h to select this from DISTRO_DEFAULTS so that
boards which have selected DISTRO_DEFAULTS will keep the same configuration
as before without needing any defconfig file changes.
The initial list of selected things matches all settings recently removed
from config_distro_defaults.h because they have been converted to Kconfig,
with the exception of CMD_ELF and CMD_NET, which have a default of y, if
the default of these ever changes they should be selected by DISTRO_DEFAULTS
too.
For testing and example purposes this commit also converts ARCH_SUNXI
to use DISTRO_DEFAULT instead of selecting everything it needs itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
To make the PSCI backend more maintainable and easier to port to newer
SoCs, rewrite the current PSCI implementation in C.
Some inline assembly bits are required to access coprocessor registers.
PSCI stack setup is the only part left completely in assembly. In theory
this part could be split out of psci_arch_init into a separate common
function, and psci_arch_init could be completely in C.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Instead of hardcoding the GIC addresses in the PSCI implementation,
provide a base address in the cpu header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CPUCFG has an unlisted debug control register, which is used to disable
external debug access.
Also, sun7i secondary core power controls are in CPUCFG, as there's no
separate PRCM block.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Instead of listing individual registers for controls to each processor
core, list them as an array of registers. This makes accessing controls
by core index easier.
Also rename "cpucfg_sun6i.h" (which was unused anyway) to the more generic
"cpucfg.h", and add packed attribute to struct sunxi_cpucfg.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
cpucfg_sun6i.h includes a register definition for the CPUCFG register
block. The types used are u32 and u8, which are defined in linux/types.h.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
struct sunxi_prcm_reg is a representation of the PRCM registers. Add
the packed attribute to prevent the compiler from doing funny things.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Use SUNXI_CPUCFG_BASE across all families. This makes writing common
PSCI code easier.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The PSCI implementation expects at most 2 pages worth of space reserved
at the end of the secure section for its stacks. If PSCI is relocated to
secure SRAM, then everything is fine. If no secure SRAM is available,
and PSCI remains in main memory, the reserved memory space doesn't cover
the space used by the stack.
If one accesses PSCI after Linux has fully booted, the memory that should
have been reserved for the PSCI stacks may have been used by the kernel
or userspace, and would be corrupted. Observed after effects include the
system hanging or telinit core dumping when trying to reboot. It seems
the init process gets hit the most on my test bed.
This fix allocates the space used by the PSCI stacks in the secure
section by skipping pages in the linker script, but only when there is
no secure SRAM, to avoid bloating the binary.
This fix is only a stop gap. It would be better to rework the stack
allocation mechanism, maybe with proper usage of CONFIG_ macros and an
explicit symbol.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some common PSCI functions are written in assembly, but it should be
possible to use them from C code.
Add function declarations for C code to consume.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For psci_get_cpu_stack_top() to be usable in C code, it must adhere to
the ARM calling conventions. Since it could be called when the stack
is still unavailable, and the entry code to linux also expects r1 and
r2 to remain unchanged, stick to r0 and r3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
The dts file this commit adds is identical to the one submitted to
the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This gives us a bit more breathing room wrt our SPL size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tegra186's HSP module implements doorbells, mailboxes, semaphores, and
shared interrupts. This patch provides a driver for HSP, and hooks it
into the mailbox API. Currently, only doorbells are supported.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The DRAM PHY layer on PH1-LD20 is able to calibrate PHY parameters
periodically. This compensates for the voltage and temperature
deviation and improves the PHY parameter adjustment. Instead, it
requires 64 byte scratch memory in each DRAM channel for the dynamic
training. The memory regions must be reserved in DT before jumping
to the kernel.
The scratch area can be anywhere in each DRAM channel, but the DRAM
init code in SPL currently assigns it at the end of each channel.
So, it makes sense to reserve the regions on run-time by U-Boot
instead of statically embedding it in the DT in Linux. Anyway,
a boot-loader should know much more about memory initialization
than the kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This will make it easier to select config options specific to
particular ARM processor generation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The setjmp/longjmp implementation did not work on thumb1 implementations
because it used instruction encodings that don't exist on thumb1 yet.
This patch limits itself to thumb1 instruction set for 32bit arm and
removes a superfluous printf along the way.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch is doing the following:
1. Implementing the errata for LS2080.
2. Adding fixup for fdt for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
This errata a008751 is applied on Soc specific file currently.This will be
moved to a file where all the errata implementation will take place for usb
for fsl. This patch removes the errata workaround from soc specific file
for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Adds get_svr and IS_SVR_REV helpers for ARMv8 platforms,
similar to PPC and ARMv7.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.
Fixes: 74cc8b097d ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add initial support for NXP's S32V234 SoC and S32V234EVB board.
The S32V230 family is designed to support computation-intensive applications
for image processing. The S32V234, as part of the S32V230 family, is a
high-performance automotive processor designed to support safe
computation-intensive applications in the area of vision and sensor fusion.
Code originally writen by:
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>