Use like the other boards a text file for the environment.
As this is the last user of keymile-common.h we can now remove this
file completely.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Use already present common.env file and add a powerpc specific env
so that we can move all the environment defines to text files.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Replace MTDPARTS_DEFAULT in the config include file by
CONFIG_MTDPARTS_DEFAULT in defconfig to complete the Kconfig migration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Replace MTDPARTS_DEFAULT in the config include file by
CONFIG_MTDPARTS_DEFAULT in defconfig to complete the Kconfig migration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Replace MTDIDS_DEFAULT and MTDPARTS_DEFAULT in the config include file by
CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT in defconfig to complete
the Kconfig migration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Replace MTDIDS_DEFAULT in config include file by CONFIG_MTDIDS_DEFAULT
in defonfig to complete the Kconfig migration
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Introduce the minimum configs, only SD-MMC and UART boot related
settings, to serve as a good starting point for the am62a as we add more
functionality.
Signed-off-by: Bryan Brattlof <bb@ti.com>
[trini: Disable CONFIG_NET as it's not used, in both platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move this out of board file as this is done by the DM based NAND flash
driver. The EBI chip select configuration, iomux and timings are
handled by the driver
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
As DM_ETH is required for all network drivers, it's now safe to remove
the non-DM_ETH support code. Doing this removes some board support code
which was also unused. Finally, this removes some CONFIG symbols that
otherwise needed to be migrated to Kconfig, but were unused in code now.
Signed-off-by: Tom Rini <trini@konsulko.com>
In practice, it is clear that the usage in m68k of
CONFIG_WATCHDOG_TIMEOUT is setting a value in milliseconds. Rename this
to the existing symbol and move to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
We move the existing CONFIG_POST_* functionality over to CFG_POST and
then introduce CONFIG_POST to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Given that we can use Kconfig logic directly to see if we have a program
available on the host or not, change from passing NO_SDL to instead
controlling CONFIG_SANDBOX_SDL in Kconfig directly. Introduce
CONFIG_HOST_HAS_SDL as the way to test for sdl2-config and default
CONFIG_SANDBOX_SDL on if we have that, or not.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Perform some deeper investigation on the remaining symbols listed in
this file and remove more.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move a number of legacy USB UDC options to Kconfig, over from the config
header.
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_RTC_DS1337
CONFIG_RTC_DS1337_NOOSC
CONFIG_RTC_DS1338
CONFIG_RTC_DS1374
CONFIG_RTC_DS3231
CONFIG_RTC_MC13XXX
CONFIG_RTC_MXS
CONFIG_RTC_PT7C4338
Signed-off-by: Tom Rini <trini@konsulko.com>
This option controls using board/samsung/common/misc.c, so add a Kconfig
file there as well and select it from the boards which use this
functionality.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This is only used on sandbox, so select it there.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On platforms that use DM_PWM, we do not need to define this value
anymore, so remove it from config files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_POWER_FSL
CONFIG_POWER_FSL_MC13892
CONFIG_POWER_HI6553
CONFIG_POWER_LTC3676
CONFIG_POWER_PFUZE100
CONFIG_POWER_PFUZE3000
CONFIG_POWER_SPI
CONFIG_POWER_TPS65090_EC
CONFIG_POWER_TPS65218
CONFIG_POWER_TPS65910
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the SRIO namespace do not
easily transition to Kconfig. In many cases they likely should come from
the device tree instead. Move these out of CONFIG namespace and in to
CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SRIO1
CONFIG_SRIO2
CONFIG_SRIO_PCIE_BOOT_MASTER
CONFIG_SYS_SRIO
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_TIMER_COUNTS_DOWN
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are now no flags being set in these files, so remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This moves SYS_SATA_FAT_BOOT_PARTITION to Kconfig and enforces the
current default via Kconfig rather than C code.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_NOBQFMAN
CONFIG_SYS_DPAA_DCE
CONFIG_SYS_DPAA_FMAN
CONFIG_SYS_DPAA_PME
CONFIG_SYS_DPAA_RMAN
CONFIG_SYS_PMAN
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_PCI and
CONFIG_SYS_PCIE namespace do not easily transition to Kconfig. In many
cases they likely should come from the device tree instead. Move these
out of CONFIG namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_OMAP_ABE_SYSCK
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NUM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SPL_NS16550_MIN_FUNCTIONS
CONFIG_SYS_NS16550_MEM32
CONFIG_SYS_NS16550_PORT_MAPPED
CONFIG_SYS_NS16550_REG_SIZE
CONFIG_SYS_NS16550_SERIAL
To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that
platforms can enable the legacy driver here for SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is specific to the PowerPC SPL implementation, so rename
this to reflect that it's in SPL and used / tested there, so that we can
then safely migrate it to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NOR
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_PAGE_2K
CONFIG_SYS_NAND_PAGE_4K
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_MAX_OOBFREE
CONFIG_SYS_NAND_MAX_ECCPOS
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is the only driver, and only one platform makes use of, setting
CONFIG_SYS_NAND_ECC_BASE. Reference ATMEL_BASE_ECC directly in this
case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_HW_ECC
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_HW_ECC_OOBFIRST
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit removes the following unused symbols:
CONFIG_SYS_NAND_DDR_LAW
CONFIG_SYS_NAND_ECCSTEPS
CONFIG_SYS_NAND_ECCTOTAL
CONFIG_SYS_NAND_ENABLE_PIN_SPL
CONFIG_SYS_NAND_MX7_GPMI_62_ECC_BYTES
CONFIG_SYS_NAND_U_BOOT_RELOC_SP
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DBW_8
CONFIG_SYS_NAND_DBW_16
Note that all instances of the code check for CONFIG_SYS_NAND_DBW_16
being defined, and then "else" to CONFIG_SYS_NAND_DBW_8 whereas all of
the configs set CONFIG_SYS_NAND_DBW_8. So we introduce
CONFIG_SYS_NAND_DBW_16 as an option.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Re-add the old PHY reset binding for nanopi-k2
-----BEGIN PGP SIGNATURE-----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=yEaP
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20221122' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Implement setbrg op to meson serial device
- Re-add the old PHY reset binding for nanopi-k2
The sandbox config file is to be removed. Move the GUID declarations
needed for capsule update functionality to the board file where they
are used.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement setbrg in amlogic/meson serial device with driver model
similar to how the meson_uart.c driver does it in Linux. Also
configure (probe) the serial device with the new reg5 register.
Signed-off-by: Edoardo Tomelleri <e.tomell@gmail.com>
Link: https://lore.kernel.org/r/20220918161701.572814-1-e.tomell@gmail.com
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Instead of overwriting $loadaddr variable, use custom temporary
$fileloadaddr variable. So scripts can access default/original address
stored in $loadaddr at build time.
Signed-off-by: Pali Rohár <pali@kernel.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NONCACHED_MEMORY
To do this we introduce CONFIG_SYS_HAS_NONCACHED_MEMORY as a bool to
gate if we are going to have noncached_... functions available and then
continue to use CONFIG_SYS_NONCACHED_MEMORY to store the size of said
cache. We make this new option depend on both the architectures which
implement support and the drivers which make use of it.
Cc: Tom Warren <twarren@nvidia.com>
Cc: Mingming lee <mingming.lee@mediatek.com>
Cc: "Ying-Chun Liu (PaulLiu)" <paul.liu@linaro.org>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN
To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_MMC_MAX_DEVICE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This converts the following to Kconfig:
CONFIG_SYS_MMC_MAX_BLK_COUNT
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_LOADS_BAUD_CHANGE
CONFIG_LOADS_ECHO
As part of this, we move CMD_SAVES to be after CMD_LOADS as they are
logically related (load or save an s-record format file) and this makes
grouping of CONFIG_SYS_LOADS_BAUD_CHANGE easier.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce three options, one for each observed L3 cache size, and have
the size select'd as needed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce two options, one for each observed L2 cache size, and have the
size select'd as needed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This removes the following symbols:
CONFIG_RTC_MCFRRTC
CONFIG_SYS_JFFS2_FIRST_BANK
CONFIG_SYS_JFFS2_FIRST_SECTOR
CONFIG_SYS_JFFS2_NUM_BANKS
CONFIG_SYS_LBC_CACHE_BASE
CONFIG_SYS_LIME_SIZE
CONFIG_SYS_MAMR
CONFIG_SYS_MCFRRTC_BASE
CONFIG_SYS_MONITOR_SEC
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_INTERLAKEN
CONFIG_SYS_ISA_IO
CONFIG_SYS_ISA_IO_BASE_ADDRESS
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_INIT_RAM_LOCK
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_I2C_INIT_BOARD
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The imx8mn_beacon board does not use the same memory map as the reference
design from NXP or other imx8mn boards. As such, memory is more limited
in SPL.
Moving SPL_BSS_START_ADDR and SPL_STACK to default locations increases
the amount of available meory for the SPL stack. Doing this allows
the board to no longer define CONFIG_MALLOC_F_ADDR.
Since SYS_LOAD_ADDR also does not align with other boards, move it too.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The IMX8M based Venice boards all have device-tree fec nodes that
use proper dt with a phy-handle pointing to a phy with reg assigned
to the proper phy address.
There is no need to keep using the CONFIG_FEC_MXC_PHYADDR hack when
a proper dt is used - remove it.
This was previously done in commit 400eebf10d
("configs: imx8m{m, n}_venice: remove unneeded CONFIG_FEC_MXC_PHYADDR")
but got clobbered by commit 6889412ad5
("Convert CONFIG_SYS_BARGSIZE to Kconfig")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
remove unused ifdef left behind after commit ca3369df71
("configs: drop CONFIG_SPL_ABORT_ON_RAW_IMAGE")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for the MSC SM2S-IMX8PLUS SMARC Module. Tested in conjunction
with the MSC SM2-MB-EP1 Mini-ITX Carrier Board.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
The RD-AC5X-32G16HVG6HLG-A0 development board main components and
features include:
* Main 12V/54V power supply
* 270 Gbps throughput packet processor on the main board
* DDR4:
* SR1: 2GB DDR4 2400MT/S(1GB x 2 pcs ) with ECC(1GB x 1 pcs)
* SR2: 4GB DDR4 2400MT/S(2GB x 2 pcs ) with ECC(2GB x 1 pcs)
* PCB co-layout with 4GB device to support 8GB (Dual CS) requirement
* 16GB eMMC (Samsung KLMAG1JETD-B041006)
* 16MB SPI NOR(GD25Q127C)
* 32 x 1000 Base-T interfaces
* 16 x 2500 Base-T interfaces
* SR1: 88E2540*4
* SR2: 88E2580*1+88E2540*2
* Six (6) x 25G Base-R SFP28 interfaces
* One (1) x RJ-45 console connector, interfacing to the on board UART
* One (1) x USB Type-A connector, interfacing to the USB 2.0 port (0)
* One (1) x USB Type-mini B connector, interfacing to the USB 2.0 port (1)
* One (1) x RJ-45 1G Base-T Management port, interfacing to the host
port (shared with PCIe) Connected to 88E1512 Gigabit Ethernet Phy
* One (1) x Oculink port, interfacing to the PCIe port for external CPU
connection
* POE 802.3AT support on Port 1 ~ Port 32, 802.3BT support on Port 33 ~
Port 48 (Microsemi PD69208T4, PD69208M or TI TPS2388,TPS23881
solution)
* POE total power budget 780W
* LED interfaces per network port/POE
* LED interfaces (common) showing system status
* PTP TC mode Supported (Reserved M.2 connector to support BC mode)
Signed-off-by: Chris Packham <judge.packham@gmail.com>
File name with pattern u-boot-spl* is used on all places except in kwb
image for binary with SPL-only code. Combined binary with both SPL and
proper U-Boot in other places has file name pattern u-boot-with-spl*.
Make it consistent also for kwb image and rename u-boot-spl.kwb to
u-boot-with-spl.kwb as this image contains both SPL and proper U-Boot code.
Also update documentation about file name changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_MIPS_TIMER_REQ
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CPU_CLOCK_RATE is just used once for CONFIG_SYS_MIPS_TIMER_FREQ
which is migrated to Kconfig in the next patch.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Resolve all uses of CONFIG_SYS_MHZ with the currently defined value.
Remove code which depends on CONFIG_SYS_MHZ but where no board configs
actually use that code.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
So far the Calxeda machines were using the CONFIG_SYS_TIMER_* macros to
simply hardcode the address of the counter register of the SP804 timer.
This method is deprecated and scheduled for removal.
Use the newly introduced SP804 DM_TIMER driver to provide timer
functionality on Highbank and Midway machines. The base address and base
frequency are taken from the devicetree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Enabling capsule update functionality on the platform requires
populating information on the images that are to be updated using the
functionality. Do so for the DK2 board.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
BCM6753 is essentially same as the main chip BCM6855 but with different
SKU number. Now that BCM6855 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6855, remove the original ARCH_BCM6753 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm96753ref board folder. It is replaced by the
generic bcmbca board folder.
- Merge the 6753.dtsi setting to the new 6855.dtsi file. Update
96753ref board dts with the new compatible string.
- Delete broadcom_bcm96763ref.h and merge its setting to the new
bcm96855.h file.
- Delete bcm96753ref_ram_defconfig and use a basic config version of
bcm96855_defconfig
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6855 is a Broadcom ARM A7 based PON Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
broadband SoC, this patch adds it under CONFIG_BCM6855 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL101 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM6858 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6858, remove the original ARCH_BCM6858 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm968580xref board folder. It is replaced by the generic
bcmbca board folder.
- Update bcm968580xref board dts with the new compatible string.
- Delete broadcom_bcm968580xref.h and merge its setting to the new
bcm96858.h file.
- Remove bcm968580xref_ram_defconfig as a basic config version of
bcm96858_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6858 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other broadband
SoC, this patch adds it under CONFIG_BCM6858 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and the
original dts is updated with the one from linux next git repository.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM68360 is a variant within the BCM6856 chip family. Now that BCM6856
is supported under CONFIG_ARCH_BCMBCA and CONFIG_BCM6856, remove the
original ARCH_BCM68360 support and migrate its configuration and dts
settings. This includes:
- Remove the bcm968360bg board folder. It is replaced by the generic
bcmbca board folder.
- Merge the 68360.dtsi setting to the new 6856.dtsi file. Update board
dts with the new compatible string.
- Merge broadcom_bcm968360bg.h setting to the new bcm96856.h file.
- Remove bcm968360bg_ram_defconfig as a basic config version of
bcm96856_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6856 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other Broadband
SoC, this patch adds it under CONFIG_BCM6856 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and Broadcom uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM63158 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM63158, remove the original ARCH_BCM63158 support and migrate
configuration settings.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63158 is a Broadcom B53 based DSL Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
Broadband SoC, this patch adds it under CONFIG_BCM63158 chip
config and CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL011 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM4908 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added
under ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux git repository so the dts and dtsi
files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM6813 is a Broadcom B53 based PON and WLAN AP router SoC. It is part
of the BCA (Broadband Carrier Access origin) chipset family so it's
added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4912 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts
and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63146 is a Broadcom B53 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63138 is an ARM A9 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory, ARM A9 global timer
and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
This patch applies on top of the my previous patch [1].
[1] https://lists.denx.de/pipermail/u-boot/2022-August/490570.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63148 is an Broadcom B15 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6756 is an ARM A7 based WLAN Gateway and Access Point Broadband SoC.
It is part of the BCA(Broadband Carrier Access origin) chipset family so
it's added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6878 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011
uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6846 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM63178 is an ARM A7 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
This option should not have the SYS_ in it. Drop it so it fits in with the
other video options.
Also simplify the alignment code in gunzip_bmp(), since malloc() always
returns a 32-bit-aligned pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the distro config env memory layout for the Verdin iMX8M Mini and
Verdin iMX8M Plus again:
- loadaddr=0x48200000 allows for 128MB area for uncompressing (ie FIT
images, kernel_comp_addr_r, kernel_comp_size)
- fdt_addr_r = loadaddr + 128MB - allows for 128MB kernel
- scriptaddr = fdt_addr_r + 512KB - allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB - allows for 512KB script
Memory layout taken from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout").
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Note that this corrects a pre-maturely applied version 2 of the same
patch set.
Fixes: bbe0089d29 ("verdin-imx8mm: verdin-imx8mp: update env memory layout")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
At the moment the QEMU boot sequence tries various (storage) devices
when trying to find a payload to boot.
To simplify starting a specific kernel and initrd, there is also the qfw
command, which can use the files specified on the QEMU command line, via
the -kernel and -initrd options.
Add this command to the list of boot options to try. Since users
specifying those options on the command line probably explicitly want
to run them, let's place the new command first. Without those options,
the qfw command will just gracefully fail, and we continue with the
existing order.
This allows auto-booting of specific kernels in QEMU, for instance in CI
systems.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
With sf update fixed to support unaligned start offset, use plain
sf update to update the bootloader in SPI NOR. This also helps
avoid the case where not enough SPI NOR has been erased and the
bootloader has been written to unerased area, and thus corrupted.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Update the distro config env memory layout for the Apalis iMX6,
Colibri iMX6, Colibri iMX6ULL and Colibri iMX7:
- loadaddr=0x84200000 (resp. 0x14200000 on them i.MX 6) allows for 64MB
area for uncompressing (ie FIT images)
- fdt_addr_r = loadaddr + 64MB : allows for 64MB kernel
- scriptaddr = fdt_addr_r + 512KB : allows for 512KB fdt
- pxefile_addr_r = scriptaddr + 512KB : allows for 512KB script
- ramdisk_addr_r = pxefile_addr_r + 512KB : allows for 1MB extlinux.conf
Memory layout analogous to 64-bit one from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout") but left pxefile_addr_r
updated according to doc/develop/distro.rst.
This fixes a potential issue caused by the compressed kernel being
relocated on top of the ramdisk causing its corruption.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
After commit 395110284b ("nitrogen6x: Populate FDTFILE at build-time
for all platforms") iMX.6Q Sabrelite fails to boot due to a bad fdtfile
string:
Retrieving file: /dtbs/5.18.0-0.deb11.4-armmp/"imx6q-sabrelite".dtb
** File not found /dtbs/5.18.0-0.deb11.4-armmp/"imx6q-sabrelite".dtb **
CONFIG_DEFAULT_DEVICE_TREE option is string typed, so __stringify() is
adding extra quotes. Remove this.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
... to avoid loosing characters when pasting text into the serial console.
This allows to remove the workaround to disable the vidconsole output
when no HDMI device is detected. This workaround only was there to speed-up
serial console processing.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The first production revision of the MX8M Mini Menlo board implements
a hardware change which swaps console UART and another UART connector.
Implement the swap, which maps the console UART back to the way Verdin
console is mapped.
Signed-off-by: Marek Vasut <marex@denx.de>
Move the environment from the board header to a separate text file
and also drop those variables that are already set in env_default.h
from the Kconfig options.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move the environment from the board header to a separate text file
and also drop those variables that are already set in env_default.h
from the Kconfig options or are not needed anymore.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The default load addresses for the various payloads (kernel, DT,
ramdisk) on systems with just 32MB of DRAM have some issues:
For a start the preceding comment doesn't match the actual values:
apparently they were copied from the 64MB S3 layout, then halved, but
since 0x5 is NOT the half of 0x10, they don't match up.
Also those projected maximum sizes are quite restrictive: it's not easy
to build a compressed kernel image with just 4MB. The only defconfig in
mainline Linux that supports the F1C100s (the only 32MB user so far)
creates a 6MB compressed / 15MB uncompressed kernel.
Rearrange the default load addresses to accommodate such a kernel: we
allow an 7MB/16MB kernel, and up to 5MB of ramdisk, stuffing the smaller
binaries like the DTB towards the end, just before the relocated U-Boot.
Shrink the size for DTB and scripts on the way, there is no need for
allowing up to 512K for them.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Traditionally we assumed that every Allwinner board would come with at
least 256 MB of DRAM, and set our DRAM layout accordingly. This affected
both the default load addresses, but also U-Boot's own address
expectations (like being loaded at 160 MB).
Some SoCs come with co-packaged DRAM, but only provide 32 or 64MB. So
far we special-cased those *chips*, as there was only one chip per DRAM
size. However new chips force us to take a more general approach.
Introduce a Kconfig symbol, which provides the minimum DRAM size of the
board. If nothing else is specified, we use 256 MB, and default to
smaller values for those co-packaged SoCs.
Then select the different DRAM maps according to this new symbol, so
that different SoCs with the same DRAM size can share those definitions.
Inspired by an idea from Icenowy.
This is just refactoring: compiled for all boards before and after this
patch: the binaries were identical.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Fix typo that was caused by the same feature being split in to 2 different
configuration options. Replace CONFIG_USBNET_DEVADDR with
CONFIG_USBNET_DEV_ADDR
Signed-off-by: Ignacio Zamora <nachopitt@gmail.com>
These boards are out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
- SPL fixes for STM32F7 MCUs
- Device tree alignement with kernelv6.0-rc4 for MCU's board
- Device tree alignement with kernelv6.0-rc3 for MPU's board
- Update DDR node for STM32MP15
- Cleanup config file for STM32MP1
- Update for cmd_stm32key command
- Fix compatible string to add partitions for STM32MP1
- Update for stm32programmer tool
-----BEGIN PGP SIGNATURE-----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=iA80
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220927' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Increase SYS_MALLOC_F_LEN for STM32 MCU's board
- SPL fixes for STM32F7 MCUs
- Device tree alignement with kernelv6.0-rc4 for MCU's board
- Device tree alignement with kernelv6.0-rc3 for MPU's board
- Update DDR node for STM32MP15
- Cleanup config file for STM32MP1
- Update for cmd_stm32key command
- Fix compatible string to add partitions for STM32MP1
- Update for stm32programmer tool
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYzGwogAKCRDKSWXLKUoM
Ial4AJ9+4WHn0MV2X7gK1fyh4lUW7ggPhQCggsYlSoACgMgdji17SAPhCv/W3IA=
=BmA9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc1-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1 (round 2)
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
By pressing "c" key during SPL execution, we force U-boot execution
instead of a kernel XIP image.
This fixes a hard fault when booting stm32f746-disco in SPL with "c"
key pressed during SPL execution.
U-Boot SPL 2022.10-rc5-00009-g40d02baa91 (Sep 20 2022 - 17:21:21 +0200)
Trying to boot from XIP
Hard fault
pc : 080083fc lr : 08000d1b xPSR : 21000000
r12 : 2004f108 r3 : 080083fd r2 : 00000028
r1 : 2004f0c8 r0 : 2004f0e4
Resetting CPU ...
This is due to SYS_UBOOT_START flag set to 0x080083FD which is not correct.
If unset, SYS_UBOOT_START is set by default to CONFIG_SYS_TEXT_BASE
which match with our requirement.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Waldemar Brodkorb <wbx@openadk.org>
Versal NET platform is based on Versal chip which is reusing a lot of IPs.
For more information about new IPs please take a look at DT which describe
currently supported devices.
The patch is adding architecture and board support with soc detection
algorithm. Generic setting should be very similar to Versal but it will
likely diverge in longer run.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/320206853dc370ce290a4e7b6d0bb26b05206021.1663589964.git.michal.simek@amd.com
This patch adds general board files based on MT7981 SoCs.
MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:
1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add general board files based on MT7986 SoCs.
MT7986 uses one mmc controller for booting from both SD and eMMC.
Both MT7986A and MT7986B use the same pins for spi controller.
Configs for various boot types:
1. mt7986_rfb_defconfig - SPI-NOR and SPI-NAND for MT7986A/B
2. mt7986a_bpir3_emmc_defconfig - eMMC for MT7986A only
3. mt7986a_bpir3_sd_defconfig - SD for MT7986A only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Remove the unnecessary comment after the CONFIG_SYS_BOOTM_LEN
migration to Kconfig.
Fixes: c45568cc4e ("Convert CONFIG_SYS_BOOTM_LEN to Kconfig")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Update the distro config env memory layout for the Verdin iMX8M Mini and
Verdin iMX8M Plus:
- loadaddr=0x48280000 allows for 128.5MB area for uncompressing (ie FIT
images, kernel_comp_addr_r, kernel_comp_size)
- fdt_addr_r = loadaddr + 127.5MB : allows for 127.5MB kernel
- scriptaddr = fdt_addr_r + 512KB : allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB : allows for 512KB script
Memory layout taken from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout") but moved loadaddr by an
additional 0.5MB to avoid "Moving Image from 0x48200000 to 0x48280000"
during booti plus actually defining kernel_comp_size to make booti work.
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Erase the entire U-Boot area during U-Boot update instead of just
a subset of it. This way, in case u-boot-with-spl.imx grows, the
sf write won't write over non-erased part of the SPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
* Drop legacy /boot/PPTImage.md5 check
* Update device tree naming
* Update t30args#0 root cmd line property to support latest kernel
versions (root=/dev/mmcblk0p2 for linux < 4 and
root=/dev/mmcblk1p2 for linux >= 4)
* Add custom bootloader version string
* Destroy invalid dtb at ${dtbaddr} and configuration script at
${cfgaddr} to ensure proper boot in warm restart case.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Commit 0ea4fc4dcf ("board/BuR: invalidate ${dtbaddr} before cfgscr")
destroys the boot targets b_t30lgcy#0 and b_t30lgcy#1. The reason behind
this is, that b_t30lgcy#0 and b_t30lgcy#1 both load the for booting
needed device trees from mmc and the cfgscr script patches those. Because
of this, cfgscr is not allowed to destroy the previously loaded device
tree otherwise cfgscr will fail.
This patch moves the device trees invalidation on warm restart to the
PREBOOT cmd to fix that issue.
Fixes: 0ea4fc4dcf ("board/BuR: invalidate ${dtbaddr} before cfgscr")
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The SPI and NAND board variants never went into production.
Drop those board variants.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
These macros are not used anymore in microblaze code since commit
f113d7d303 ("Convert CONFIG_SPL_STACK to Kconfig"), so remove them.
Fixes: f113d7d303 ("Convert CONFIG_SPL_STACK to Kconfig")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-1-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
$fdt_addr is mandatory for systems which provides DTB in HW (e.g. ROM) and
wishes to pass that DTB to Linux.
Turris Mox contains DTB binary in SPI NOR memory at "dtb" partition which
starts at offset 0x7f0000 and is 0x10000 bytes long.
Armada 3700 CPU does not allow mapping SPI NOR memory into physical address
space like on other architectures and therefore set $fdt_addr variable to
memory range in RAM and loads this DTB binary from SPI NOR in misc_init_r()
function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmMZoW4ACgkQ4rK92eCq
k3W2MAgAsmy2aSlMYo/AGlJ/KCrZuk6OirNHtdOdacvbcdUUbpkNpBSjdkrRm2If
VUnY1utIIJe6gFgnBUxXJ3RF5FZuhkdawc6V25HtDp6H3WamzJknKs5Vc4TlKp59
hZCOto7/+G/cd2XLdCKFUBl+new1pdDPsEm56+57DeZ7QGAQRX35PUQ5+HBjQJ/N
n/wJgS6wkEdIQLLwmCVxbHUkC+pRotTza5F2A0qZJgYPMcMpVFYKtzIa4GbWB5YS
MKGHbM8f3C8RLPQaHHTRycoA2Yor1I52B4Oi7605c5zHQr9pjrgtWsernDzkIhsB
ThYHSYQBUBTY4HBfzFwzCkVGqqLWNg==
=PMFY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220907' of https://source.denx.de/u-boot/custodians/u-boot-stm
- simplify the STM32MP15x package parsing code
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
Correctly calculate offsets between SPL and proper U-Boot when new config
option CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR for generating eSDHC boot sector
is enabled. Otherwise SPL would not be able to boot proper U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
All *boot env commands overrides default boot source location via i2c.
After board reset without power off, BootROM then starts booting U-Boot
from this specified location instead of the default one.
Add new env command defboot which reverts boot location to the default
value, which in most cases is configurable by HW DIP switches.
And add new env commands norlowerboot, norupperboot, sd2boot to boot from
other locations. norlowerboot would instruct BootROM to boot from lower NOR
bank, norupperboot from upper NOR bank and sd2boot from SD card with
alternative configuration.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SYS_HZ_CLOCK was wrongly set to 1GHz whereas it's set to 750MHz
by default by bootrom.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Grzegorz Szymaszek <gszymaszek@short.pl>
The frequency of the system counter is static which is given by the
COUNTER_FREQUENCY option. Remove COUNTER_FREQUENCY_REAL.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This converts CONFIG_SYS_L2_PL310 to Kconfig.
For omap2 and mvebu the 'select SYS_L2_PL310' locations were
determined using ./tools/moveconfig -i CONFIG_SYS_L2_PL310.
For mx6 I manually chose ARCH_MX6 as 'select' location. The
correctness has been verified using
$ ./tools/moveconfig.py -f ARCH_MX6 ~SYS_L2_PL310 ~SYS_L2CACHE_OFF
0 matches
That means whenever an ARCH_MX6 board had SYS_L2_PL310 disabled, this
was correctly reflected in SYS_L2CACHE_OFF. Thus it's safe to insert
the 'select' statement under ARCH_MX6.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
This removes the following symbols:
CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS
CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS
CONFIG_SYS_I2C_LDI_ADDR
CONFIG_SYS_I2C_DVI_ADDR
CONFIG_SYS_I2C_DVI_BUS_NUM
They are unused by any code in tree at this time.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_EEPROM_CCID
CONFIG_SYS_I2C_EEPROM_NXID
CONFIG_SYS_EEPROM_BUS_NUM
Signed-off-by: Tom Rini <trini@konsulko.com>
Just enabling the Kconfig option for DM_ETH and DM_MDIO is enough.
Additionally, we can remove the old hardcoded config.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
If something is wrong with the environment, we cannot rely on a proper
u-boot operation anymore. In fact, it is possible, that we never reach
misc_init_r() with a broken environment.
Also don't enable the netconsole by environment settings. This way the
user don't have to reconfigure the environment. Instead the network
console is only enabled when the push button is pressed during boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the common kernel_addr_r, ramdisk_addr_r and fdt_addr_r variable
names.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
We can load the ramdisk as the last step. This way we don't have to set
the intermediate variable 'ramdisk_len' and can remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Drop our own CONFIG_FDTFILE handling in favor of the generic
CONFIG_DEFAULT_FDT_FILE one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add distro boot to board include file and deconfig file
- Miscellaneous changes:
- Remove Gerald from maintainer list (email bounced)
- Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy
kernel method of booting (e.g. OpenWrt) with appended DTB.
- Add CONFIG_UBIFS_SILENCE_MSG to reduce binary size.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220807192709.21717-1-pali@kernel.org/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
- Add distro boot to board include file and deconfig file
- Miscellaneous changes:
- Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy
kernel method of booting (e.g. OpenWrt) with appended DTB.
- Add CONFIG_LTO and CONFIG_UBIFS_SILENCE_MSG, and disable some
unused configs to reduce binary size.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220807192709.21717-1-pali@kernel.org/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The kmtegr1 board is out of maintenance and can be removed. As it is the
only board in the tree using MPC8309 the support for this CPU is dropped
completely.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
This board is missing migration to CONFIG_DM, which had a deadline of
v2020.01, which is now more than 2 years passed due. Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we are about to enable DM_ETH by default, remove legacy code.
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have been orphaned for some time and are behind on various
DM migrations. Remove them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is not converted to use CONFIG_DM, well passed the migration
deadline. Remove it.
Cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The LS1043ARDB rev v7.0 board replaces the AQR105 PHY on MAC9 with an
AQR113C PHY. The address of the PHY on the MDIO bus changes from 0x1 to
0x8. Enable CONFIG_OF_BOARD_FIXUP and update both u-boot and Linux device
trees to reflect this change.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
This driver has not been converted to DM_ETH. The migration deadline
passed 2 years ago.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
This converts the following to Kconfig:
CONFIG_FSL_NGPIXIS
CONFIG_SYS_FSL_QMAN_V3
CONFIG_SYS_FSL_RAID_ENGINE
CONFIG_SYS_FSL_RMU
CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
CONFIG_SYS_FSL_SRIO_LIODN
CONFIG_SYS_FSL_TBCLK_DIV
CONFIG_SYS_FSL_USB1_PHY_ENABLE
CONFIG_SYS_FSL_USB2_PHY_ENABLE
CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
And we remove the entries from the README for a number of already
converted items.
Signed-off-by: Tom Rini <trini@konsulko.com>
Only two boards in the tree set the macro DWC_NET_PHYADDR. Both have
CONFIG_DM_ETH_PHY=y, so should set the phy address in DT if necessary.
The imx8mp_evk does set the correct address in device tree.
The other board seems to be a copy-paste-adapt from an old
version of the imx8mp_evk config header, given the "#ifdef
CONFIG_DWC_ETH_QOS" block that has been removed from imx8mp_evk header
in commit 127fb45495. Its device tree doesn't even enable (i.e., set
'status = "okay"') the &eqos node. But the other ethernet device,
&fec, does get enabled, and does have a phy sitting at address 4 (and
it also has a corresponding legacy #define CONFIG_FEC_MXC_PHYADDR
4). So I believe it should be completely safe to remove it from there
as well.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[trini: Re-apply to top of tree, update imx93_evk.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
There are a large number of options under CONFIG_SYS (but some of these
are elsewhere, spotted while cleaning CONFIG_SYS) that are never
referenced, or only used slightly later in the config file. Remove or
restructure these.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FLASH_ERASE_TOUT
CONFIG_SYS_FLASH_LOCK_TOUT
CONFIG_SYS_FLASH_UNLOCK_TOUT
CONFIG_SYS_FLASH_WRITE_TOUT
In practice, for two m68k platforms we move to hard-coding with a
comment the timeout values, rather than try and make convoluted Kconfig
logic. We add options for the write and erase options to the pic32
flash driver, as this driver does make use of them. Everywhere else
these are unreferenced values.
Signed-off-by: Tom Rini <trini@konsulko.com>
All platforms today define CONFIG_SYS_DDR_RAW_TIMING, so drop the code
for this option being unset.
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is the only platform defining and using CONFIG_SYS_MEM_SIZE, switch
to using CONFIG_SYS_SDRAM_SIZE for consistency.
Cc: Paul Burton <paul.burton@mips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a number of CONFIG_SYS_xxx_SIZE options to describe the amount
main memory available. Rework CONFIG_SYS_DDR_SIZE, which described a
size in number of MiB to use CONFIG_SYS_SDRAM_SIZE which is most often
used as a number of bytes. Use shifts of this option when required.
Signed-off-by: Tom Rini <trini@konsulko.com>
No platforms enable the functionality to tftp directly to NOR flash, and
this is discouraged by the documentation. Remove this code. Further,
this highlights an oddity of the code. Un-indent the start of this
function.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now when CONFIG_SYS_TEXT_BASE has sane value, use it for calculation of
other SPL offset values: CONFIG_SPL_MAX_SIZE, CONFIG_SYS_MMC_U_BOOT_* and
CONFIG_SYS_SPI_FLASH_U_BOOT_* macros.
No functional change.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
FEC_QUIRK_ENET_MAC is defined in the imx-regs.h include file and thus
does not need to be defined in the various board config includes.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add support for 96Boards Dragonboard 845C aka Robotics RB3 development
platform. This board complies with 96Boards Open Platform Specifications.
Features:
- Qualcomm Snapdragon SDA845 SoC
- 4GiB RAM
- 64GiB UFS drive
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/sdm845.rst, board: dragonboard845c.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The macro `CONFIG_SYS_UBOOT_BASE` is used by SPL loaders `"NOR"` and
`"XIP"` to determine the base address of u-boot.
For `"NOR"` on i.MX8MM it is the base address of QSPI0 plus the offset
of the flattened image tree blob.
Although `QSPI0_AMBA_BASE` is used to define CONFIG_SYS_UBOOT_BASE in
multiple board header files for i.MX8MM, it is not specified.
Specify offset of flattened image tree blob (needs to be set to same
value as specified in 'binman' node), base address of QSPI0 and size of
FlexSPI configuration block.
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This allows to compile U-Boot without some boot option for some A3720 board
which does not have that peripheral.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
For mostly historic reasons we had configuration headers for each
Allwinner CPU "family". These days they are mostly just including one
common header, with the rest being somewhat empty.
There were attempts to remove them, and to just use the one common header
to begin with, but this has implications to the build system, which me
might not be ready for, yet.
To document this behaviour, and to avoid something sneaking in over
time, make those files all the same (minus the CPU family name and
the copyrights), and add a comment explaining that.
This makes it easier to just remove those files later on, when needed
and possible.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds support for MediaTek MT7621 SoC.
All files are dedicated for u-boot.
The default build target is u-boot-mt7621.bin.
The specification of this chip:
https://www.mediatek.com/products/homenetworking/mt7621
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmLNj88ACgkQ4rK92eCq
k3Wukwf+PZnmQuyzwwFDOpZO1lUPfUN0WkoEBV8M5IxLehHdfHJT3YsAtm6DS8dd
4+n0+WmR7Uk4B8ODRPrGNBJftFoOVfEAvWmpfCC/VcHgEDEzdJzJe6yxa9wAWeQR
djRZLM8qx6OIEUW+sfYbFkD2BCv+cLiT0YH9qqx8WCRlf6JTuLquSBJQXIJAqYiE
LdO/pp0rv4oC0s08BSL4bHL/Mh7FHeUPiEjn2uRP/vISgmH1qyCql3gbr/wCaTYR
jfqr9pjmWTxEOppZIdE832QMy1MTSA/6Q3Jr4LKRko6ArBGjbGlj3EbeeEdKPDRy
BtQ6OLnxWKdcPr2qp301nnERRi4L4w==
=WgbW
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220712' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Alignment with Linux kernel device tree v5.19 for stm32mp15 and stm32mp13
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
MPS3 board have a ISP1763 usb controller, enable it to be used
for mass storage access for example. Enable the usb command
also and for the FVP support for mass storage enable the mmc
command.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
On STM32MP13x STMicroelectronics boards, the UART can reliably go up to
4000000 bauds when connected to the external ST-LINKV3.
This patch adds the support of higher baudrates on STMicroelectronics
STM32MP13x boards with ST-LINKV3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Correctly handle STM32MP_BOARD_EXTRA_ENV define in stm32mp15_st_common.h;
the STM32MP_BOARD_EXTRA_ENV is added in CONFIG_EXTRA_ENV_SETTINGS
definition, as it is done "stm32mp15_st_common.h"
Without this patch, the content of STM32MP_BOARD_EXTRA_ENV is not used in
the default environment for STMicroelectronics boards.
Fixes: 806c4dd315 ("configs: stm32mp1: set the console variable for extlinux.conf")
Reported-by: Gatien CHEVALLIER <gatien.chevallier@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On p1_p2_rdb_pc platforms, we set ddr_data_init to the "poison" value of
0xdeadbeef rather than a real calculated / derived value. Do this
directly and comment rather than via CONFIG.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a single platform that is both in the OMAP3 family of parts, but
has an EMIF4 memory controller. Currently we hard-code the size of
chip select 0. Make this more clear by putting the value in the
function rather than a CONFIG option.
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix multiple issues in ubifs distroboot code:
U-Boot supports attaching only one MTD device as UBI at the time. So
always call 'ubifsmount ubi0:${bootubivol}' for mounting UBI volume
${bootubivol}. Usage of 'ubi${devnum}' is incorrect as 'ubi part'
command attach MTD device always as UBI device ubi0.
Set distroboot ${bootfstype} variable to ubifs in ubifs_boot command.
Distroboot scripts require ${bootfstype} variable to be properly set and it
is already set for all other boot types.
Set distroboot ${distro_bootpart} variable to ${bootubivol} value. UBI
device does not have partitions, but has volumes. Distroboot scripts
require something to be set in ${distro_bootpart} variable, so set it to
the UBI volume which is currently mounted by ubifs.
Set distroboot ${devnum} variable to fixed string "ubi0". ubifs code
differs from the other partition code that it requires "ubi" prefix before
number.
Explicitly unmount ubifs volume after loading all data from it. This allows
to detach UBI device from MTD device.
Move definition of MTD device with UBI and UBI volume with ubifs filesystem
from global env variables ${bootubipart} and ${bootubivol} into the
distroboot "func" macro, defined in board include config files. UBIFS
distroboot macros then set ${bootubipart} and ${bootubivol} local variables
for compatibility with existing distroboot scripts.
This last change allows to define more UBIFS target devices and make it
clear what is boot MTD/UBI device.
All board include config files are adjusted to use this new scheme of
specifying boot MTD/UBI device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
This converts the following to Kconfig:
CONFIG_SYS_BOOTM_LEN
As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
We only reference CONFIG_SYS_BFTIC3_BASE in one location. Move the
comment to where we reference it, and use the value directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
As this is used in the environment, reference it directly rather than as
a CONFIG value.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Adrian Alonso <adrian.alonso@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
Signed-off-by: Tom Rini <trini@konsulko.com>
All of these symbols are not referenced anywhere else in the code, so
remove them.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
On platforms that use CONFIG_USB_OHCI_NEW we do not need to set
CONFIG_SYS_USB_OHCI_REGS_BASE nor CONFIG_SYS_USB_OHCI_SLOT_NAME. Drop
these from platforms that we can.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point, the only user of ohci-hcd that also uses PCI is using DM,
so we can drop CONFIG_PCI_OHCI* usage. No platforms set either of
CONFIG_SYS_USB_OHCI_BOARD_INIT or CONFIG_SYS_USB_OHCI_CPU_INIT so those
hooks can be removed as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_OHCI_SWAP_REG_ACCESS
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
CONFIG_SYS_USB_OHCI_SLOT_NAME
CONFIG_USB_ATMEL
CONFIG_USB_ATMEL_CLK_SEL_PLLB
CONFIG_USB_ATMEL_CLK_SEL_UPLL
CONFIG_USB_OHCI_LPC32XX
CONFIG_USB_OHCI_NEW
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_KIRKWOOD_EGIGA_INIT
CONFIG_KIRKWOOD_PCIE_INIT
CONFIG_KIRKWOOD_RGMII_PAD_1V8
CONFIG_KM_DISABLE_PCIE
Signed-off-by: Tom Rini <trini@konsulko.com>
These CONFIG options are only used on this board, in the board file
itself. Remove these from the CONFIG namespace and define in the board
file.
Signed-off-by: Tom Rini <trini@konsulko.com>
The symbol CONFIG_PCI_CLK_FREQ is local to this board. Provide equal
clarity in the code by referencing the numeric value directly and move
the explanatory comment to the code, just prior to use.
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver is not enabled anywhere, remove it. Also remove definitions
of symbols only used in this driver, on platforms that did not enable
it.
Signed-off-by: Tom Rini <trini@konsulko.com>
As things stand currently, there is only one PowerPC platform that
enables the options for CHAIN_OF_TRUST. From the board header files,
remove a number of never-set options. Remove board specific values from
arch/powerpc/include/asm/fsl_secure_boot.h as well. Rework
include/config_fsl_chain_trust.h to not abuse the CONFIG namespace for
constructing CHAIN_BOOT_CMD. Migrate all of the configurable addresses
to Kconfig.
If any platforms are re-introduced with secure boot support, everything
required should still be here, but now in Kconfig, or requires migration
of an option to Kconfig.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SAMSUNG_ONENAND
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
We rename the S5P specific "CONFIG_PWM" to CONFIG_PWM_S5P and move it to
Kconfig. Given the usage of CONFIG_PWM_NX, we have that select this new
symbol.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- Drop the emulator CONFIG test from include/configs/ls1088ardb.h
- Migrate CONFIG_SYS_FSL_DDR_EMU to a select'able option in
drivers/ddr/fsl/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
As this driver can dynamically determine the values set in
CONFIG_DW_WDT_BASE when using WDT, so make this depend on WDT rather
than migrate CONFIG_DW_WDT_BASE to Kconfig.
Cc: Chee Tien Fong <tien.fong.chee@intel.com>
Cc: Chin-Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinh.nguyen@intel.com>
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Stefan Roese <sr@denx.de>
Cc: hee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This value is always used at the default, rename it for now. This
likely should come from the device tree if non-default, moving forward.
Signed-off-by: Tom Rini <trini@konsulko.com>
From whole P1/P2 family of RDB boards is TDM-PMC card (PCI Mezzanine Card,
Freescale PQ-MDS-T1) available only on P1021RDB and P1025RDB boards.
So address mapping for TDM-PMC card on LBC should not be enabled on any
other P1/P2 RDB board as there is no device at that TDM-PMC address.
Support for P1021RDB and P1025RDB boards was already removed from mainline
U-Boot in commits 6d1dd76afe ("board/freescale: Remove P1021RDB board
support") and d521cece5a ("board/freescale: Remove P1025RDB board
support").
So do not enable TDM-PMC address mapping on remaining P1/P2 RDB boards and
remove all macros related to TDM-PMC address mappings.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add defconfig and Kconfig files for Google Chameleon V3 board
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The configs ROCKCHIP_CHIP_TAG and ROCKCHIP_MAX_INIT_SIZE were
originally added with rksd.c, rkspi.c and rkcommon.c in mind,
but are no longer in use and replaced by struct spl_info,
so remove unused configs for tag and size.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move the environment text over from being set via
CONFIG_EXTRA_ENV_SETTINGS in include/configs/gw_ventana.h and over
to plain text in board/gateworks/gw_ventana/gw_ventana.env. This lets
us drop CONFIG_EXTRA_ENV_SETTINGS_COMMON as everything resides in a
single environment file now.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
- Ensure that everyone setting mtdids= and mtdparts= is doing so via the
CONFIG options.
- If the CONFIG options are set, ensure that the default environment
sets mtdparts / mtdids.
Signed-off-by: Tom Rini <trini@konsulko.com>
The "autoload" environment variable is always checked with env_get_yesno
as it can be set to any form of no. The default behavior of
env_get_yesno is to return -1 on variables that are not set, which acts
as true in general (we test for non-zero return). To convert
CONFIG_SYS_AUTOLOAD to Kconfig, given that it was almost always used to
set autoload to no, first rename to CONFIG_SYS_DISABLE_AUTOLOAD for
consistency sake. Then, make it so that if enabled we set autoload=0 in
the default environment. Migrate all platforms which set
CONFIG_SYS_AUTOLOAD to non-true or that set autoload to false in their
default environment to using CONFIG_SYS_DISABLE_AUTOLOAD
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the environment text over from being set via
CONFIG_EXTRA_ENV_SETTINGS in include/configs/opos6uldev.h and over to
plain text in board/armadeus/opos6uldev/opos6uldev.env. This lets us
manage env_version without a CONFIG variable.
Cc: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_RANGE
Now that this is in Kconfig we can enforce a minimum size and so remove
the check in C code to ensure range is larger than size.
Signed-off-by: Tom Rini <trini@konsulko.com>
With the exception of distro_boot support, we can move all of the rest
of the environment changes to come from CONFIG_EXTRA_ENV_TEXT and in
turn remove CONFIG_ENV_REFLASH.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This define is only currently used in a single board, and always set to
one. Define this within the board code and remove other references.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_MIN_ENTRIES
CONFIG_ENV_MAX_ENTRIES
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the exception of how PowerPC handles SPL and TPL (which has its own
issues), we cannot safely hide options under CONFIG_SPL_BUILD. Largely
remove the places that have this test today.
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce board/siemens/common/Kconfig and have it hold FACTORYSET to
start with. Use select for this on the boards that need it.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Following how it's done for the majority of drivers, add a new
VIDEO_EXYNOS option and Kconfig file under drivers/video/exynos and list
the current options there.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since bb5930d5c9 ("exynos: video: Convert several boards to driver
model for video") there have been no callers of any of the exynos_lcd_*
family of functions. Remove these from the boards, and then remove
unused logo and related code as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
The only platform currently that defines an ide_preinit function has an
empty one that immediately returns. Remove this hook.
Signed-off-by: Tom Rini <trini@konsulko.com>
The migration deadline for this has passed and all boards have been
updated, remove this legacy code and references for it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The migration deadline for this has passed and all boards have been
updated, remove this legacy code and references for it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The only use of CONFIG_XTFPGA was to build all of the in-tree device
trees. Switch to using CONFIG_XTENSA instead of a non-Kconfig symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
Passing the mtdparts environment variable to the Linux kernel is
required to properly mount the UBI rootfs.
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The Linux kernel device tree already specifies the device to be used for
boot console output with a stdout-path property under /chosen.
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
Replace XILINX_DCACHE_BYTE_SIZE macro with two Kconfig symbols for
instruction and data caches sizes, respectively:
CONFIG_XILINX_MICROBLAZE0_ICACHE_SIZE
CONFIG_XILINX_MICROBLAZE0_DCACHE_SIZE
Also, get rid of the hardcoded value in icache_disable().
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-8-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com> (s/bralid/brlid/g)
CONFIG_SYS_INIT_SP_OFFSET macro place stack to TEXT_BASE - SYS_MALLOC_F_LEN
but there is no reason to do it now because board_init_f_alloc_reserve()
returns exact location where stack should be. That's why stack location is
calculated at run time and there is no need to hardcode it via macro. This
change will help with placing U-Boot to any address.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e9aee69646e022fd8a96cbee2d2a07ab81fb6e05.1655299267.git.michal.simek@amd.com
Do not use 0 as address for memory because of the special meaning for
pointers (null pointer). Change the spl bss start address to the second
page.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220607074314.27125-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmKsehgACgkQ4rK92eCq
k3UexAf+JThCd7FlN3OkTVKIdZKeNm2KpQxrqt20whiqp/nSUzxXrjdlCTKZEER2
lLJoVnwr+bkmdlqsa6gAZXSsd0lUv37XnLsLA5or278tFNlKp6gzYrz49FR59mVC
ie7/NlY5FgM5qmKGCob7tjwJ78r2/S3T2EaLiAMWUmw2UB5KZU6h3napHZ+1T0se
vaEAVRzAaZeYzKU3k6RBSv2tXQ6ssvfpp9RcXpRGtrN908AqDhHiOfntuOrnsEe0
9rjY1DSXO9a5WqHRm2KQ3FrA/By2layQ+4WH/HgIPHasisnmo3E/euVWmhtTaiT/
g5bOLwyFQ2/RvdMlMxXlKUcuMfNwRA==
=Hhzj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220620' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Add STM32MP13 SoCs support with associated board STM32M135F-DK
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
Code for changing boot source is platform generic and can be used by any
P1* and P2* compatible RDB board. Not only by boards which use config
header file p1_p2_rdb_pc.h.
So move this code from p1_p2_rdb_pc.h to p1_p2_bootsrc.h and cleanup macros
for generating boot source env variables in CONFIG_EXTRA_ENV_SETTINGS.
This allows to use code for resetting board and rebooting to other boot
source also by other boards in future.
Signed-off-by: Pali Rohár <pali@kernel.org>
Replace reference to the correct name STMicroelectronics
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove STM32_SYSRAM_END and clean the comments in stm32mp15_common.h file
after moving some CONFIG to Kconfig: CONFIG_SYS_CBSIZE,
CONFIG_SPL_MAX_FOOTPRINT, CONFIG_SYS_SPL_MALLOC_START and
CONFIG_SYS_SPL_MALLOC_SIZE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Introduce the code in mach-stm32mp and the configuration file
stm32mp13_defconfig for the new STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When migrating CONFIG_CONS_INDEX to Kconfig, on this platform we changed
what "board" evaluated to in the environment. This in turn meant that
we would no longer try and find the correct fdtfile via the normal
distro boot logic. Fix this by overriding board in the default
environment, as done on other platforms where CONFIG_SYS_BOARD is not
what we want to be in the board environment variable.
Fixes: f76750d111 ("Convert CONFIG_CONS_INDEX et al to Kconfig")
Reported-by: Gabriel Hojda <ghojda@yo2urs.ro>
Tested-by: Gabriel Hojda <ghojda@yo2urs.ro>
Signed-off-by: Tom Rini <trini@konsulko.com>
Clean up in ubiload script. Unmount UBIFS from which kernel image was
loaded and detach UBI on which the UBIFS is located, otherwise message
similar to the following is printed just before booting kernel:
Removing MTD device #7 (rootfs) with use count 1
Error when deleting partition "rootfs" (-16)
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
CONFIG_SPL_RAW_IMAGE_SUPPORT default y has been used to replace
CONFIG_SPL_ABORT_ON_RAW_IMAGE for quite some time, so drop
CONFIG_SPL_ABORT_ON_RAW_IMAGE.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_SPL_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart3 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_SPL_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm_beacon
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mn_beacon
Since these boards has CONFIG_DM_SERIAL and/or CONFIG_SPL_DM_SERIAL,
the legacy macro no need to be defined.
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Soeren Moch <smoch@web.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
systemd prints its messages on the last console= statement that it finds
in the kernel arguments. The current ordering sends the systemd messages
to tty1, by default this is the display.
Ensure that systemd sends its messages to the default UART, reorder the
console= statements accordingly.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add am62x_evm_r5_defconfig for R5 SPL and am62x_evm_a53_defconfig for
A53 SPL and U-Boot support.
To keep the changes to minimum. Only UART And SD boot related configs
are included. This should serve as good starting point for new board
bringup with AM62x.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[trini: Migrate a number of CONFIG symbols, have re-tested]
Tested-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is the initial support for Broadcom's ARM-based 47622 SOC.
In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.
The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
rootwait=1 is not a valid kernel boot parameters. According
to the documenation is only rootwait
rootwait [KNL] Wait (indefinitely) for root device to show up.
Useful for devices that are detected asynchronously
(e.g. USB and MMC devices).
Fix:
Unknown kernel command line parameters "rootwait=1", will be passed to user space.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
CONFIG_SPL_BOOT_DEVICE was made obsolete by
CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC,SATA,UART}.
CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI is the default so existing users of
CONFIG_SPL_BOOT_DEVICE can simply have the option removed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is needed on some Marvell SoCs when
booting from MMC. All existing usages of this have the same value so
make this the default and have the Kconfig option depend on SPL &&
MVEBU_SPL_BOOT_DEVICE_MMC.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases, when we don't use CONFIG_SPL_FRAMEWORK nor are we on
PowerPC using their specific SPL/TPL framework, we need to specify the
start.S file to use for these typically very constrained systems. Do
this within the Makefile logic, rather than introducing a string-based
CONFIG option, as this would get slightly complex to do in Kconfig for a
very limited number of users.
Signed-off-by: Tom Rini <trini@konsulko.com>
The address where the device tree will be passed in to U-Boot at is now
moved to the Kconfig file. If this is user configurable, it needs to be
exposed rather than hidden, and should probably be renamed as well.
Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_ARGS_ADDR
In doing so, we also consistently use this variable for SPL_OS_BOOT and
not CONFIG_SYS_FDT_BASE in some cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is mostly unused. In the case where it is currently used, it means
the same as CONFIG_SPL_PAD_TO, which is already set for the platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START
We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_RELOC_TEXT_BASE
CONFIG_SPL_RELOC_STACK
CONFIG_SPL_RELOC_MALLOC_ADDR
CONFIG_SPL_RELOC_MALLOC_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX7
platforms, and move the existing large comment from imx7_spl.h to
doc/imx/common/imx7.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX6
platforms, and move the existing large comment from imx6_spl.h to
doc/imx/common/imx6.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have GENERATED_GBL_DATA_SIZE to tell us how large the generated
global data is, so do not use a hard-coded value of 1024 for it.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the places where PowerPC references CONFIG_SYS_GBL_DATA_OFFSET it
does so as (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET). And
it defines CONFIG_SYS_GBL_DATA_OFFSET in the same manner that other
architectures define CONFIG_SYS_INIT_SP_OFFSET. Other architectures
define CONFIG_SYS_INIT_SP_ADDR as (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_INIT_SP_OFFSET) typically. Rename things within PowerPC for
consistency with other architectures.
Signed-off-by: Tom Rini <trini@konsulko.com>
This value is only referenced by PowerPC code in a way other than
directly as CONFIG_SYS_INIT_SP_ADDR. Switch to CONFIG_SYS_INIT_SP_ADDR
directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This value is only referenced by PowerPC code in a way other than
directly as CONFIG_SYS_INIT_SP_ADDR. Switch to CONFIG_SYS_INIT_SP_ADDR
directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases, we define CONFIG_SYS_INIT_SP_ADDR differently for SPL or
full U-Boot. This case should be making use of CONFIG_SPL_STACK, as
that's what that variable is for. In a few other cases we define
CONFIG_SPL_STACK directly to CONFIG_SYS_INIT_SP_ADDR, but do not need to
as the code handles this correctly, normally.
Signed-off-by: Tom Rini <trini@konsulko.com>
The definition of CONFIG_SPL_BOOTROM_SAVE is always a fixed
CONFIG_SPL_STACK + 4, while CONFIG_SPL_STACK is not constant. This
change will make it clear where the location is still, once
CONFIG_SPL_STACK moves to Kconfig.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of PowerPC platforms define this, for SPL. To move this to
Kconfig, it needs to be CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE, so use
CONFIG_IS_ENABLED() to check for usage. A number of layerscape
platforms bring this logic from PowerPC, but only need a small part of
it, for the fman driver. Remove their unused portion at least.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_SYS_MALLOC_SIMPLE
The problem here is that a few platforms have been doing:
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
instead of defining CONFIG_SPL_SYS_MALLOC_SIMPLE directly. Correct this
and update the documentation in a few places to match usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_INIT_MINIMAL
CONFIG_SPL_FLUSH_IMAGE
CONFIG_SPL_SKIP_RELOCATE
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only referenced in non-SPL_DM cases, of which there are
currently none. Remove this option and slightly re-organize the code is
there is now never an if/else at the start of spl_sata_load_image()
Signed-off-by: Tom Rini <trini@konsulko.com>
This is always defined to 2, and referenced in two places. Move the
define to <asm/omap_common.h> and make sure the code that uses this
includes that file. Make <asm/arch-omap*/clock.h> not include that
file, as we don't need to be doing so.
Signed-off-by: Tom Rini <trini@konsulko.com>
Set kernel_comp_addr_r and kernel_comp_size for compressed kernel.
Adjust existing addresses for ramdisk, so that kernel_comp_addr_r
comes before the ramdisk image, since the decompressed kernel size
is known to us. This way we can allow big ramdisk image to be loaded.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Set kernel_comp_addr_r and kernel_comp_size for compressed kernel.
Adjust existing addresses for ramdisk, so that kernel_comp_addr_r
comes before the ramdisk image, since the decompressed kernel size
is known to us. This way we can allow big ramdisk image to be loaded.
Update unleashed.rst to remove the manual environment configuration
for compressed kernel boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Move kernel_comp_addr_r to an address that comes before the ramdisk
image, since the decompressed kernel size is known to us. This way
we can allow big ramdisk image to be loaded.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYo4bYwAKCRDKSWXLKUoM
IYmTAJ9t4GDXggJ7ErB3Kk7/qSrywjEGAgCgnKQVgQvjo1B6o5aiwbk1wR86zkQ=
=W7X8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
Use the de10-nano files as templates for the de10-standard board.
The files in qts directory are generated by quartus from the GHRD
design.
Signed-off-by: Humberto Naves <hsnaves@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Use phy address from device tree instead of CONFIG_FEC_MXC_PHYADDR from
board header. This is required, because the DH picoITX and DRC02 boards
require different settings than PDK2. The corresponding 'phy-handle'
device tree properties are already there.
I tested this change on picoITX and DRC02, but on PDK2 it is untested.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.
The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.
[1] Commit 6192cf8ac082 from
git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Enable CONFIG_SPL_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
FEC_QUIRK_ENET_MAC is defined in the imx-regs.h include file and thus
does not need to be defined in the various board config includes.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX8MP SoC FEC needs to have the FEC_QUIRK_ENET_MAC defined.
Fixes: commit 2395625209 ("board: gateworks: venice: add imx8mp-venice-gw740x support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX8M based Venice boards all have device-tree fec nodes that
use proper dt with a phy-handle pointing to a phy with reg assigned
to the proper phy address.
There is no need to keep using the CONFIG_FEC_MXC_PHYADDR hack when
a proper dt is used - remove it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This converts the following to Kconfig:
CONFIG_MTD_CONCAT
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
As stm32f46-disco, stm32f769-disco and stm32746g-eval are very similar
except their respective device tree file. These 3 boards uses the same
TARGET_STM32F746_DISCO flag (so same include/configs/stm32f746-disco.h
and same board file board/st/stm32f746-disco/stm32f746-disco.c)
To be able to compile these 3 boards, replace the hard-coded device-tree
name in include/configs/stm32f746-disco.h by CONFIG_DEFAULT_DEVICE_TREE
which is set in each board defconfig file with the correct value.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This allows to concatenate spl and u-boot binaries together.
Previously, both binaries has to be flashed separately at the correct
offset (spl at offset 0 and u-boot at offset 0x8000).
With this patch, only one binary is generated (u-boot-with-spl.bin)
and has to be copied in flash at offset 0 using openocd for example
or simply copied in exported mass storage.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On STMicroelectronics boards, the UART can reliably go up to
2000000 bauds when connected to the on-board ST-LINK-V2 for STM32MP15
Unfortunately U-Boot will fall back to 115200 unless higher rates are
declared via CONFIG_SYS_BAUDRATE_TABLE.
This patch add the support of higher baudrates on STMicroelectronics
boards with ST-LINK.
Cc: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Set the environment variable "console", used in extlinux.conf file when it
is generated by YOCTO distribution with:
UBOOT_EXTLINUX_CONSOLE ??= "console=${console},${baudrate}"
With these 2 variables, U-Boot give dynamically the used console and
baudrate in the Linux kernel bootargs.
For the STMicroelectronics boards, the used console is ttySTM0.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
For CONFIG_DM_SERIAL it is required to increase CONFIG_SYS_MALLOC_F_LEN as
default value is not enough for memory hungry CONFIG_DM_SERIAL code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Currently, in case of arm64 bootloader and U-Boot the stack pointer is
initialized at an offset of NON_SECURE_MSRAM_SIZE from arm64 SPL's text
base address. After jumping to arm64, execution is done out of DDR.
Therefore, having an offset corresponding to the size of MSRAM does not
have any significance.
Instead, initialize the stack pointer after an offset of 4MB from the SPL
text base address. This helps in allocating larger memory for stack.
┌────────────────────┐0x80080000
│ │
│ arm64 SPL │
├────────────────────┤
│ ▲ │
│ │ │
│ STACK │
├────────────────────┤0x80480000
│ Memory for Load │
│ Buffer Allocation │
├────────────────────┤0x80800000
│ │
│ U-Boot Image │
│ │
└────────────────────┘
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This patch enables the Kconfig symbols needed for full ethernet support
on the EBB7304. Also the PHY autonegotiation timeout is increased, as
the default 5 seconds are sometime a bit short. With this, ethernet can
be used on this board. Here an example of a tftp load:
=> tftp ffffffff81000000 big
ethernet-mac-nexus@11800e0000000 Waiting for PHY auto negotiation to complete....... done
Using ethernet-mac-nexus@11800e0000000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.243
Filename 'big'.
Load address: 0xffffffff81000000
Loading: ################################################## 10 MiB
13.2 MiB/s
done
Bytes transferred = 10485760 (a00000 hex)
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves CONFIG_SYS_INIT_SP_OFFSET to a higher address so that
it does not interfere with larger U-Boot images. This was noticed, while
adding network support to the EBB7304 board.
Signed-off-by: Stefan Roese <sr@denx.de>
The Zyxel NSA310s board has the network chip Marvell Alaska 88E1318S.
Use uclass mvgbe and the compatible driver M88E1310 driver to bring
up Ethernet.
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Remove CONFIG_RESET_PHY_R.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add phy mode RGMII to kirkwood-nsa310s.dts
- Miscellaneous changes: Move constants to .c file and remove header file
board/zyxel/nsa310s/nsa310s.h, add support for large USB and SATA HDDs,
use BIT macro, add/cleanup comments, and cosmetic changes.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220412201820.10291-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
U-Boot for Turris Omnia is always compiled with MMC, SCSI and USB support,
so always enable macros for booting from these devices.
Signed-off-by: Pali Rohár <pali@kernel.org>
CONFIG_ETHPRIME defines primary ethernet device and env variable $ethact
stores currently active ethernet device.
So there is no point to set ethact= in default environment. Instead set
CONFIG_ETHPRIME properly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Replace hardcoded i2c hex values for NOR banks by named SW macros in
map_lowernorbank/map_uppernorbank env commands.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Replace hardcoded boot i2c bus num and address by existing macros when
generating env for CONFIG_EXTRA_ENV_SETTINGS.
Same macros are used in U-Boot board code when reading information from
boot i2c data.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Do not stringify env $vscfw_addr two times (once implicitly via string
operator "" and second time explicitly via __stringify() macro) and allow
to compile U-Boot without CONFIG_VSC7385_ENET (when __VSCFW_ADDR was not
defined and so macro name was stringified into CONFIG_EXTRA_ENV_SETTINGS).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As written in comment, P2020 has two possible SD switch configurations.
Extend code to detect both of them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With the commit that moves the BOOTCOMMAND to Kconfig:
970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
some stray ifdefs have been left in the header files which
are now useless.
Clean up the include files to remove these lines.
Fixes: 970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
On Layerscape platforms, the DTB is loaded from boot filesystem,
per the fdt_addr description in doc/README.distro, it must be
removed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enough space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
CONFIG_MMCROOT is only used to set mmcroot, no need a dedicated macro.
Script as below
"
for i in `ls include/configs/*.h`
do
mmcroot=`sed -n '/define.*MMCROOT/ p' $i | awk -F\" '{ print $2;}'`
if [ ! -n "$mmcroot" ]; then
continue
fi
sed -i '/define.*MMCROOT/ d' $i
sed -i 's,\" CONFIG_MMCROOT \",'$mmcroot',g' $i
done
"
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Sancloud BeagleBone Enhanced Extended WiFi (BBE Extended WiFi) has
its own devicetree file and the board can be identified by the 2nd
letter of the config string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The Sancloud BeagleBone Enhanced Lite (BBE Lite) has its own devicetree
file and the board can be identified by the 2nd letter of the config
string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-By: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This GPIO is actually an input "Q7_3V3_PCIE_WAKE#_IN" not an output, so
remove the misleaading and incorrect definition.
Cc: Tim Harvey <tharvey@gateworks.com> (re: pci: imx: use vpcie-supply if defined by device-tree)
Signed-off-by: Ian Ray <ian.ray@ge.com>
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Remove CONFIG_RESET_PHY_R symbol from all board files
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The Colibri PXA270 has been end-of-life since quite a while and would
require more and more maintenance (e.g. DM conversions).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable USB support for host controller and various USB ethernet
devices.
Example usage of USB Mass Storage (UMS) support:
u-boot=> mmc list
FSL_SDHC: 0
FSL_SDHC: 1
FSL_SDHC: 2 (eMMC)
u-boot=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe30000
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use PREBOOT as well. This allows a customer to just set fdt_board as
on any other module to customize the device tree for his carrier
board.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop optional support for the ancient Apalis iMX6 V1.0 hardware which
had the UART wired as DCE rather than DTE.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop legacy nfsboot script in favor of distroboot DHCP boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use the same name of DHCP Distroboot script as in regular eMMC case.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Include SCSI in the list of boot targets if CONFIG_CMD_SCSI is
enabled.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
