This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Synchronize the u-boot and kernel imx device trees, using tuned
script from commit c0157bdcafa1 ("ARM: dts: imx: use generic name bus")
Per devicetree specification, generic names are recommended to be
used, such as bus.
i.MX AIPS is an AHB - IP bridge bus, so we could use bus as node
name.
Script:
sed -i "s/\<aips@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips@/bus@/" arch/arm/dts/vf*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/vf*.dtsi
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Update the mx7ulp wdog disable sequence to avoid potential reset
issue in unlock or refresh sequence. Both sequence need two words
write to wdog CNT register in 16 bus clocks window, if miss the
window, the write will cause violation in wdog and reset the chip.
Current u-boot code is using writel() function which has a DMB
barrier to order the memory access. The DMB between two words write
may introduce some delay in certain circumstance, causing the wdog
reset due to 16 bus clock window requirement.
Also, WDOG1 might have been enabled already depending on FUSE hence
we need to be as close as possible to its reconfiguration timing
requirement of 128 bus clock limit.
This patch replaces writel() function by __raw_writel() to avoid such
issue, and improve to check if watchdog is already disabled or
unlocked.
Signed-off-by: Ye Li <ye.li@nxp.com>
Co-developed-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Co-developed-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Add u-boot.dtsi specific to imx6-apalis with a watchdog enabled.
If OP-TEE is loaded by SPL, it may use a watchdog to handle fails of
u-boot running. Enable the watchdog in SPL to use it by OP-TEE.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since c6df0e2ffd ("net: phy: micrel: add support for DLL setup on ksz9131")
the Micrel PHY driver correctly configures the delay register. The Verdin PHY
is RGMII-ID, so reflect that in DT, otherwise the ethernet no longer works.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.
This updates imx8mp_evk and phyCORE-i.MX8MP as they share the
same binman config.
Updated also imx8mp_evk documentation.
Tested on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Since derivatives are moving to binman from usage of the FIT generator
script, and considering the warning introduced in f4a43d2925
("Makefile: Warn against using CONFIG_SPL_FIT_GENERATOR"), usage of FIT
generator is discouraged.
Current FIT generator also generates broken output, since commit
3f04db891a ("image: Check for unit addresses in FITs") prohibits using
'@' for unit addresses but the generator script still emits the old
sematics.
Remove the generator script and corresponding call in Makefile, all
derivatives should be migrated to binman in order to provide binary
images.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently imx8mm-cl-iot-gate_defconfig fails to produce a working boot
binary due to the lack of fip.bin:
" BINMAN all
Image 'main-section' is missing external blobs and is non-functional: blob-ext
Some images are invalid"
To make the build process more consistent with the other i.MX8M targets,
split the defconfig in two:
- imx8mm-cl-iot-gate_defconfig: standard defconfig that only
requires ATF / DDR firmware.
- imx8mm-cl-iot-gate-optee_defconfig: "more advanced" defconfig that
requires ATF / Optee / mbedtls / DDR firmware.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
When TEE is loaded, we need to restrict the memory usage based
on rom_pointer[0]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
After the enforcement of DM_MMC the microSD card is not detected. Fix by
correctly configuring the card detect in the devicetree.
Signed-off-by: Andrej Rosano <andrej.rosano@f-secure.com>
According to 8MM/MN/MP reference manual, their pad registers only have
4 valid DSE values. And DSE2 and DSE4 are different with current
definitions in iomux-v3.h. Fix the issue to align with manual.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
cherry-picked from NXP code:
719d665a87c6: ("MLK-20467 imx8m: Fix issue for booting signed image through uuu")
which fixes secure boot on imx8m based boards. Problem was
that FIT header and so IVT header too, was loaded to
memallocated address. So the ivt header address coded
in IVT itself does not fit with the real position.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com>
read the address where the IVT header must sit
from IVT image header, loaded from SPL into
an malloced buffer and copy the IVT header
to this address
May make this dependend on SoC ?
Signed-off-by: Heiko Schocher <hs@denx.de>
- pcie_dw_meson: fix usb fail when pci link fails to go up
- Sync Amlogic DT from Linux 5.14
- dwc3-meson-gxl: add AXG compatible
- dts: keep back HW order for MMC devices since change in Upstream Linux
- Cleanup local AXG DT USB nodes now everything is upstream
- distro_bootcmd: run pci enum for scsi_boot just like it is done for nvme_boot
- New Boards:
- Odroid-HC4: a variant of Odroid-C4 with 2 SATA ports (via PCIe-SATA bridge)
- Beelink GS-King X: A variant of the other Beelink board with 2 SATA ports (via USB3-SATA bridge)
- Banana Pi M5: another credit card SBC
- JetHub D1/H1: home automation controllers
- Radxa Zero: another RPi Zero sized SBC
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmFe7jcACgkQd9zb2sjI
SdGrHhAAw2pN+4fzO/NdKa1DdRoZMXidv6nSLfIKHizvdZIoGfQo2c5FfYhDR/mz
oQeqYpLZZSONXFOd5V2idvlVPHljruV3MTSadiNb5d1Gd41HT7a/tnQ/SOpuWGlh
Jt146Zli09z55DMkUQGMv94UtCcRkNKjnaibb+ysmU8iqBk2/xstRUGvRwwxUoPv
hHlEL59VAiHwSNGzu8pUk+EyWOiixD5sNs50YgbXXnErYtVhhXqJCAhkTDGC3c+w
eU+0wK3g7imruYo9nWRZm13oNC6+HjBceODXwXhUDlP7SN82Q7Q2K9iCgMo3vhNL
fn6M/EOLqJRa3vVnFL6env7aJ+68iIS1IKEkPjQ0zuyGhDLhQ12zVf+pBFpeaLpC
ZnYCD1AE1UHlJn7kEWq+lNhXVZYIuDRIPh489YzQM3kv7ctkvsFz53jmv2nxy9a6
xz3E4Y5pTC8AXZrtxEbP0CKW+33EHFYUpiUVfTNY1tk1y848mRhYBJ9BCjSd+gK1
NYbjPcM9O/2OnnmvzCwvSijkStCges8Ma3knHmUQFcIi+kGEduyGsLDgB2GTsYdn
oTIFj0NiiSRS0TVBm6Si4tCo+Mxqv5RPx3Bd6sYC9dERSAou1UrkbX29+yROr+a2
nYMsXSDPEs51aJx5tZ+CWrB4EY1xQEo5OBEDHL0t5ZZkh8y7Njg=
=pDip
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20211007' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Add new SoC ID for S905Y2 found in Radxa Zero
- pcie_dw_meson: fix usb fail when pci link fails to go up
- Sync Amlogic DT from Linux 5.14
- dwc3-meson-gxl: add AXG compatible
- dts: keep back HW order for MMC devices since change in Upstream Linux
- Cleanup local AXG DT USB nodes now everything is upstream
- distro_bootcmd: run pci enum for scsi_boot just like it is done for nvme_boot
- New Boards:
- Odroid-HC4: a variant of Odroid-C4 with 2 SATA ports (via PCIe-SATA bridge)
- Beelink GS-King X: A variant of the other Beelink board with 2 SATA ports (via USB3-SATA bridge)
- Banana Pi M5: another credit card SBC
- JetHub D1/H1: home automation controllers
- Radxa Zero: another RPi Zero sized SBC
Import the initial dts queued for Linux 5.16.y
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Alpha sort the Amlogic dtb list (same as the kernel).
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for new home automation devices.
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console
Patches from:
- JetHub H1
https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.inhttps://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
- JetHub D1
https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.inhttps://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: removed unused variable value]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Beelink GS-King X is a variant of the GS King boards but with an internal
USB to SATA bridge and advanced audio features.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Odroid-HC4 is a variant of the Odroid-C4 board but with a PCIe-SATA bridge
instead of the USB3 ports.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Since Linux commmit [1], the order is fixed with aliases, in order to keep the
MMC device order, set it back to HW order in U-Boot dtsi files.
[1] ab547c4fb39f ("arm64: dts: amlogic: Assign a fixed index to mmc devices")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import Amlogic DT changes from Linux commit 7d2a07b76933 ("Linux 5.14"),
dt-bindings clock changes and new meson-g12b-gsking-x.dts,
meson-sm1-bananapi-m5 & odroid-hc4 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the SOC ID for the S905Y2 to board info, see below for before/after
tested with a Radxa Zero board:
SoC: Amlogic Meson G12A (Unknown) Revision 28:b (30:2)
SoC: Amlogic Meson G12A (S905Y2) Revision 28:b (30:2)
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
If Coherence Manager were not set in the beginning,
u-boot-spl would sometimes fail to boot to u-boot proper.
Enable CM and I/D cache at the same time in harts_early_init
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Provide sysreset driver using the SBI system reset extension.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Samuel Holland <samuel@sholland.org>
Add the System Reset Extension and the Hart State Management Extension
definitions.
Add missing RFENCE Extension enum values.
The SBI 0.1 extension constants are needed for the sbi command. Remove
an #ifdef.
Cf. https://github.com/riscv/riscv-sbi-doc/blob/master/riscv-sbi.adoc
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The no-map property is wrongly skipped if a no-map reserved memory
node follows one without that property. Fix this by not remembering
the absence of a no-map property across loop iterations.
Fixes: d4ea649f17 ("riscv: Provide a mechanism to fix DT for reserved memory")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This config is only used by three boards with this SOC. Most other
platforms derive this information from devicetree, and are unlikely
to ever need this config.
Moreover, it is confusing when Kconfig asks for this value under
"Support OPTEE images", but does not do anything with the value.
Move it to imx7 for those boards who still make use of it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add stub for tee_find_device function when CONFIG_TEE is not activated
to simplify the caller code.
This patch allows to remove the CONFIG_IS_ENABLED(OPTEE) tests
for stm32 platform.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Etienne Carriere <etienne.carriere@inaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
The configuration CONFIG_OPTEE is defined 2 times:
1- in lib/optee/Kconfig for support of OPTEE images loaded by bootm command
2- in drivers/tee/optee/Kconfig for support of OP-TEE driver.
It is abnormal to have the same CONFIG define for 2 purpose;
and it is difficult to managed correctly their dependencies.
Moreover CONFIG_SPL_OPTEE is defined in common/spl/Kconfig
to manage OPTEE image load in SPL.
This definition causes an issue with the macro CONFIG_IS_ENABLED(OPTEE)
to test the availability of the OP-TEE driver.
This patch cleans the configuration dependency with:
- CONFIG_OPTEE_IMAGE (renamed) => support of OP-TEE image in U-Boot
- CONFIG_SPL_OPTEE_IMAGE (renamed) => support of OP-TEE image in SPL
- CONFIG_OPTEE (same) => support of OP-TEE driver in U-Boot
- CONFIG_OPTEE_LIB (new) => support of OP-TEE library
After this patch, the macro have the correct behavior:
- CONFIG_IS_ENABLED(OPTEE_IMAGE) => Load of OP-TEE image is supported
- CONFIG_IS_ENABLED(OPTEE) => OP-TEE driver is supported
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This allows to use the watchdog in custom scripts but does not enforce
that the OS has to support it as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This adds support for the IOT2050 Basic and Advanced devices. The Basic
used the dual-core AM6528 GP processor, the Advanced one the AM6548 HS
quad-core version.
Both variants are booted via a Siemens-provided FSBL that runs on the R5
cores. Consequently, U-Boot support is targeting the A53 cores. U-Boot
SPL, ATF and TEE have to reside in SPI flash.
Full integration into a bootable image can be found on
https://github.com/siemens/meta-iot2050
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Prepares for the addition of the IOT2050 board which is based on the TI
AM65x. The board comes in four variants, Basic and Advanced, each as
product generation 1 (SR1.0) and 2 (SR2.x), so there are separate dts
files needed. Furthermore, the SPL has its own device tree.
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The WDT devices described in the general .dtsi file
should be marked as "disabled" by default.
A WDT should be then enabled in the board specific
.dts file on demands.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
This resyncs the dts files for all of the currently in-tree K3
platforms, along with relevant bindings, with the v5.14 Linux Kernel
release. Of note are that the main-navss/mcu-navss nodes were renamed
to main_navss / mcu_navss and so the u-boot.dtsi files needed to be
updated to match.
Tested on j721e_evm and am65x_evm.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last armada100 platform, remove that support
as well.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
=aQtT
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.01-rc1
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
XHCI firmware upload must be performed only once after initializing the
PCI bridge. This fixes USB stack initialization after calling "usb stop;
usb start" on Raspberry Pi 4B.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
During the migration to a single DTSI for the CP110-s specific pinctrl
compatibles were moved to the SoC DTSI as CP0 and CP1 have some specifics.
Namely, CP0 eMMC/SDIO support depends on the mvebu-pinctrl driver setting
the BIT(0) in eMMC PHY IO Control 0 Register to 0 in order for the connect
the eMMC/SDIO PHY to the controller and not use it as a MPP pin multiplexor.
So, the mvebu-pinctrl driver check specifically for the
"marvell,armada-8k-cpm-pinctrl" compatible to clear the that bit.
Issue is that compatibles in the 8040 DTSI were set to "marvell,8k-cpm-pinctrl"
for CP0 and "marvell,8k-cps-pinctrl" for the CP1.
This is obviously incorrect as the pinctrl driver does not know about these.
So fix the regression by applying correct compatibles to the DTSI.
Regression found and tested on the Puzzle M801 board.
Fixes: a0ba97e5 ("arm: armada: dts: Use a single dtsi for cp110 die description")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit 0d52bab46 (mx7dsabre: Enable DM_ETH) changed these flags from 0
(aka GPIO_ACTIVE_HIGH) to GPIO_ACTIVE_LOW. It claimed to "Also sync
device tree with v5.5-rc1", but in the linux tree, these gpios have
always been GPIO_ACTIVE_HIGH ever since this node was introduced
around v4.13 (linux commit 184f39b5).
I'm guessing that the reason for the GPIO_ACTIVE_LOW was to work
around the behaviour of the soft-spi driver back then, which
effectively defaulted to spi-mode 3 and not 0. That was arguably a bug
in the soft-spi driver, which then got fixed in 0e146993bb (spi: add
support for all spi modes with soft spi), but that commit then broke
ethernet on this board.
Fix it by setting the gpios as active high, which as a bonus actually
brings us in sync with the .dts in the linux source tree.
Without this, one gets
Net: Could not get PHY for FEC0: addr 0
No ethernet found.
With this, ethernet (at least ping and tftp) works as expected from
the U-Boot shell.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joris Offouga <offougajoris@gmail.com>
Cc: "Christian Bräuner Sørensen" <yocto@bsorensen.net>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
If mdio_register fails, it is nice to not leave behind dangling
allocated memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
After the discussion here:
https://lore.kernel.org/netdev/20210603143453.if7hgifupx5k433b@pali/
which resulted in this patch:
https://patchwork.kernel.org/project/netdevbpf/patch/20210704134325.24842-1-pali@kernel.org/
and many other discussions before it, notably:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/1512016235-15909-1-git-send-email-Bhaskar.Upadhaya@nxp.com/
it became apparent that nobody really knows what "SGMII 2500" is.
Certainly, Freescale/NXP hardware engineers name this protocol
"SGMII 2500" in the reference manuals, but the PCS devices do not
support any "SGMII" specific features when operating at the speed of
2500 Mbps, no in-band autoneg and no speed change via symbol replication
. So that leaves a fixed speed of 2500 Mbps using a coding of 8b/10b
with a SERDES lane frequency of 3.125 GHz. In fact, "SGMII 2500 without
in-band autoneg and at a fixed speed" is indistinguishable from
"2500base-x without in-band autoneg", which is precisely what these NXP
devices support.
So it just appears that "SGMII 2500" is an unclear name with no clear
definition that stuck.
As such, in the Linux kernel, the drivers which use this SERDES protocol
use the 2500base-x phy-mode.
This patch converts U-Boot to use 2500base-x too, or at least, as much
as it can.
Note that I would have really liked to delete PHY_INTERFACE_MODE_SGMII_2500
completely, but the mvpp2 driver seems to even distinguish between SGMII
2500 and 2500base-X. Namely, it enables in-band autoneg for one but not
the other, and forces flow control for one but not the other. This goes
back to the idea that maybe 2500base-X is a fiber protocol and SGMII-2500
is an MII protocol (connects a MAC to a PHY such as Aquantia), but the
two are practically indistinguishable through everything except use case.
NXP devices can support both use cases through an identical configuration,
for example RX flow control can be unconditionally enabled in order to
support rate adaptation performed by an Aquantia PHY. At least I can
find no indication in online documents published by Cisco which would
point towards "SGMII-2500" being an actual standard with an actual
definition, so I cannot say "yes, NXP devices support it".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The USB peripheral controller is the DWC2 controller 1, not 0.
Update the phandle to fix UDC support on this board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The WDT on this system should be enabled, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
On Intel Tangier the SDHCI #2 provides SD card connection.
Add GPIO card detection for it.
Fixes: 39665beed6 ("x86: tangier: Enable ACPI support for Intel Tangier")
BugLink: https://github.com/edison-fw/meta-intel-edison/issues/135
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
eMMC is non-removable on Intel Edison board. Fix the DTS accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We have individual SOC symbols for each keystone 2 platform. Use the
existing CONFIG_ARCH_KEYSTONE rather than CONFIG_SOC_KEYSTONE to
encompass all of the keystone families.
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmFR2fMRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaAnAf/ZKPy3CRphbgAmbLhNQhQGpLosLcFp343
cv53gfsv1DakLRrhqMSnOQSVoTg9P22uHbooDDR9WHfZyEL6tvGZ+dgN2/wlDhDj
wbvvsM7FB+uvLVfMF3MURQBvy4dPO+FyCm/uHmry2V2uqWPw4ss+aVhxeQ5s4/oI
LpS6yaiM8UAj2GTUZSqJ1+/W7YG9N6tL73n0PDyCvSrdCkyPWqpww1rtST88SfFI
bBEWc6ksna/29haOwHQ2xopEbVxtHv2byULfqUtnsbtE4Ozw8o0fx66tdwPHTQlM
7eSuRiEbqjlJuUZFIbMat7nb7inZkaWupZ/Sr1HUUiDdKMygrRsQhg==
=x8Uf
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-next-27sep21' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
Various of-platdata improvements, including CONFIG_OF_REAL
The cpu nodes in arch/sandbox/dts/test.dts should conform to the devicetree
specification:
* property device_type must be set to "cpu"
* the reg property must be provided
* the cpu nodes must have an address
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for accessing GPIOs using of-plata. This uses the same
mechanism as for clocks, but allows use of the xlate() method so that
the driver can interpret the parameters.
Update the condition for GPIO_HOG so that it is not built into SPL,
since it needs SPL_OF_REAL which is not enabled in sandbox_spl.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is available but not exported. More generally it does not
really work as intended.
Reimplement it and add a sandbox test too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert some of these occurences to C code, where it is easy to do. This
should help encourage this approach to be used in new code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we have a 'positive' Kconfig option, use this instead of the
negative one, which is harder to understand.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current API is outdated as it requires a devicetree pointer.
Move these functions to use the ofnode API and update this globally. Add
some tests while we are here.
Correct the call in exynos_dsim_config_parse_dt() which is obviously
wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
vexpress_ca9x4 is seemingly the only board except for qemu_arm which
is able to run U-Boot correctly, using the `-M vexpress-a9` option to
QEMU. Building for qemu_arm and running qemu-system-arm with the `-M
virt` argument has a number of downsides, most importantly that it
only supports virtio storage drivers. This significantly reduces its
usefulness in testing memory card and Flash solutions, especially when
the tested images are from a third party source.
So therefore we reintroduce the vexpress_ca9x4 board in this commit,
with the explicit goal of using it with QEMU.
A number of differences to note from the original:
* Since the board was apparently unmaintained, I have now set myself
as the maintainer.
* The board has been converted to use the driver model, which was the
reason it was removed in the first place.
* The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed
in the same commit, are not necessary for the QEMU use case, and
have been omitted.
* An `mmc0` alias was introduced in the dts file. The mmc is not
detected correctly without this, now that it's based on the device
tree instead of the board's init function.
* A couple of other nodes were removed because they were problematic
when trying to run the UEFI bootmgr. Once again, the primary use
case here is QEMU, and these nodes are not needed for that to work.
* Unnecessary board init code has been removed, thanks to driver model
and device tree.
* `CONFIG_OF_EMBED` has been enabled. I know this goes against
recommended practice, but there doesn't seem to be any other way to
pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument
does not work, I suppose because U-Boot doesn't use the same
mechanics as the kernel when it's booting.
* Load addresses have been changed to fit QEMU use case.
People wanting to get a more detailed, yet somewhat isolated, diff
between this and the original, can run this command:
git diff c6c26a05b89f25a06e7562f8c2071b60fd0c9eac~1 -- \
$( git diff-tree --diff-filter=A -r --name-only HEAD~1 HEAD)
(Make sure to either check out this commit first, or replace HEAD with
the commit ID of this commit)
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
Simplify the bootm and the spl code by using the new config
CONFIG_SUPPORT_PASSING_ATAGS.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch enables the use of the optimized memset(), memmove() &
memcpy() versions recently added on ARM64.
Please note that these optimized functions are now only enabled for
recent GCC versions (>= 9.4), as earlier GCC versions throw these
errors:
aarch64-linux-ar: warning: arch/arm/lib/memset-arm64.o: unsupported GNU_PROPERTY_TYPE (5) type: 0xc0000000
...
Signed-off-by: Stefan Roese <sr@denx.de>
[trini: Make this default to off as it causes problems on some platforms still]
Signed-off-by: Tom Rini <trini@konsulko.com>
The optimized memset uses the dc opcode, which causes problems when the
cache is disabled. This patch adds a check if the cache is disabled and
uses a very simple memset implementation in this case. Otherwise the
optimized version is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Ported from https://github.com/ARM-software/optimized-routines
These files are included from this repository, including the latest
git commit ID:
string/aarch64/memcpy.S: afd6244a1f8d
string/aarch64/memset.S: e823e3abf5f8
string/asmdefs.h: e823e3abf5f8
Note that memmove is also handled by the memcpy function.
Please note that when adding these optimized functions as default memset
memcpy functions in U-Boot, U-Boot fails to boot on the LX2160ARDB.
After the initial ATF output, no U-Boot output is shown on the serial
console. Some exception is triggered here in the very early boot process
as some of the assembler opcodes need the caches to be enabled.
Because of this, a follow-up patch will add a check to use a simple
non-optimized memset for the "cache disabled" case.
Note:
I also integrated and tested with the Linux versions of these optimized
functions. They are similar to the ones now integrated but these ARM
versions are still a small bit faster.
Signed-off-by: Stefan Roese <sr@denx.de>
On MediaTek boards we cannot override the SYS_BOARD / SYS_CONFIG_NAME
variables from defconfig.
This is because in board/mediatek/mtXXXX/Kconfig this value was override
by default due to the if CONFIG_TARGET_MTXXXX condition.
Merge all the Kconfigs to the mach-medatek/Kconfig.
This way:
- we only define SYS_{SOC,VENDOR} once
- all board definitions are in a single place, simplifying the build logic.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Add arch_lmb_reserve() implemented using arch_lmb_reserve_generic().
It is rather likely this architecture also needs to cover U-Boot with
LMB before booting Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Add arch_lmb_reserve() implemented using arch_lmb_reserve_generic().
It is rather likely this architecture also needs to cover U-Boot with
LMB before booting Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Add arch_lmb_reserve() implemented using arch_lmb_reserve_generic().
This architecture also needs to cover U-Boot with LMB before booting
Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Add arch_lmb_reserve() implemented using arch_lmb_reserve_generic().
It is rather likely this architecture also needs to cover U-Boot with
LMB before booting Linux.
Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Leo <ycliang@andestech.com>
Cc: Rick Chen <rick@andestech.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Add arch_lmb_reserve() implemented using arch_lmb_reserve_generic().
It is rather likely this architecture also needs to cover U-Boot with
LMB before booting Linux.
Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Rick Chen <rick@andestech.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Add arch_lmb_reserve() implemented using arch_lmb_reserve_generic().
It is rather likely this architecture also needs to cover U-Boot with
LMB before booting Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Tom Rini <trini@konsulko.com>
This function is clearly architecture specific code, not board specific
code. The only difference from the previous arm arch_lmb_reserve() is the
extra reservation of 16k of memory below the stack bottom, rather than
the 4k. The common code now also uses 16k alignment. Remove this custom
implementation, as it now behaves exactly as the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ye Li <ye.li@nxp.com>
According to input NXP, the 4k alignment is not always sufficient.
Currently iMX works around this problem by implementing board specific
LMB reservation, however it is likely this could also occur on other
systems. Increase the LMB reservation alignment to 16k by default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Switch arc/arm/m68k/microblaze/mips/ppc arch_lmb_reserve() to
arch_lmb_reserve_generic().
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Wolfgang Denk <wd@denx.de>
The arch_lmb_reserve() is called by lib/lmb.c lmb_reserve_common() even
if CMD_BOOTM is not enabled. However, the arc variant of arch_lmb_reserve()
is only compiled in if CMD_BOOTM is enabled.
This currently does not trigger build error, because there is an empty
weak implementation of arch_lmb_reserve(), however that is not the
function that should be used on arc.
Fix this by moving the arch_lmb_reserve() implementation into common
code and always compile it in.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
The arch_lmb_reserve() is called by lib/lmb.c lmb_reserve_common() even
if CMD_BOOT{I,M,Z} is not enabled. However, the arm32/arm64 variant of
arch_lmb_reserve() is only compiled in if CMD_BOOT{I,M,Z} is enabled.
This currently does not trigger build error, because there is an empty
weak implementation of arch_lmb_reserve(), however that is not the
function that should be used on arm32/arm64.
Fix this by moving the arch_lmb_reserve() implementation into common
code and always compile it in.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
ARMv8.0 has optional crc32 instruction for crc32 calculation. The
instruction is mandatory since ARMv8.1. The crc32 calculation is
faster using the dedicated instruction, e.g. 1.4 GHz iMX8MN gives:
=> time crc32 0x50000000 0x2000000
time: 0.126 seconds # crc32 instruction
time: 0.213 seconds # software crc32
Add implementation using the compiler builtin wrapper for the crc32
instruction and enable it by default, since we don't support any
platforms which do not implement this instruction.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
[trini: Make crc32_table guarded by CONFIG_ARM64_CRC32]
Signed-off-by: Tom Rini <trini@konsulko.com>
Replace the current 2-instruction 2-step tripling code by a
corresponding single instruction leveraging ARMv8-A's "flexible second
operand as a register with optional shift". This has the added benefit
(albeit arguably negligible) of reducing the final code size.
Fix the comment as the tripled cache level is placed in x12, not x0.
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
Improve the file's readability and conciseness by using the appropriate
Aarch64 instruction: ubfx (unsigned bitfield extract). This makes the
code easier to follow as it directly manipulates the offsets and widths
of the fields read from system registers, as they are expressed in the
Standard (ARM ARM). This has the added benefit (albeit arguably
negligible) of reducing the final code size.
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFKxpEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBLaB/0XsIdkGAvcHLWW8yUg
27GiRznikNKwn9/qIj2ByraoUd4BvxdQV4gKHR1R9n0sgYh/8VMyLbmhRoCRKFwP
3mQ0MUyjaeU5sEWzasovJVpXhuUapEiV0jEg6t3Lgwd3mp2QK2Pk87zoleQfZNkb
VAVCnt1T+kb3y0W9oa3XZbuH2wam9T5pNWRGW70JbgzdwJNKLO1Qo7MfcUNiDxJu
Jf7uXtYwwILlN38G1KSk1ymMjfaotCqj7RzNaV3Ero57MVj3VzerKGb7H+XPOYf2
nYXyietYLJJkzvHzSDwIdCSVlOSQL8QqVB8GCmLiNQD4tG830RcvSJnYpRLylWQK
6F+Y
=Q/aS
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.01 cycle:
This feature set includes : the support for CPU driver for arm926
(sam9x60 device); changes required for OP-TEE boot for sama5d2_xplained
and sama5d27_som1_ek boards; QSPI boot configuration for sama5d2_icp;
starting to remove old Kconfig unused symbols from config_whitelist.txt
(work will take more time); also small fixes and updates in mach, DT,
configs, etc.
The USB peripheral controller is the DWC2 controller 1, not 0.
Update the phandle to fix UDC support on this board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The WDT on this system should be enabled, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
On Intel Tangier the SDHCI #2 provides SD card connection.
Add GPIO card detection for it.
Fixes: 39665beed6 ("x86: tangier: Enable ACPI support for Intel Tangier")
BugLink: https://github.com/edison-fw/meta-intel-edison/issues/135
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
eMMC is non-removable on Intel Edison board. Fix the DTS accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Continue to use the "ssbl" name for GPT partition of secondary boot
stage = U-Boot for basic boot with SPL to avoid to disturb existing user.
The "fip" partition name is only used for TFA_BOOT with FIP, it is a TF-A
BL2 requirement; it the default configuration for STMicroelectronics
boards.
Fixes: b73e8bf453 ("arm: stm32mp: add defconfig for trusted boot with FIP")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Replace the number in the flexcom-mode property with the define from the
include file.
This corresponds to the approach in Linux kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The AT91 RM9200DK board was removed long time ago.
Remove existing references that were not cleaned up.
Fixes: 1c85752258 ("ARM: remove broken "at91rm9200dk" board")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixed the following DTC build warning (reproducible with W=1)
arch/arm/dts/at91-sama5d2_icp.dtb: Warning (unit_address_format): /ahb/ohci@00400000: unit name should not have leading 0s
arch/arm/dts/at91-sama5d2_icp.dtb: Warning (unit_address_format): /ahb/ehci@00500000: unit name should not have leading 0s
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Reorder the nodes following the kernel rules: nodes in a range are sorted
by ascending bus address, and when referenced by phandle, are ordered
alphabetically.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add support for sst26vf064b 64Mbit qspi-flash that is
present on sama5d2_icp board.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
[eugen.hristev@microchip.com: move u-boot properties to sama5d2_icp-u-boot.dtsi]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
sama5d2_xplained DRAM detection code will be modified to use device tree
instead of hardcoded addresses. In order to prepare that, add the memory
node to at91-sama5d2_xplained.dts.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
When SYSRESET is enabled, cpu_reset function is also defined in
sysreset-uclass.c which lead to multiple definitions of this function
since reset.c is build unconditionally. Add a check in Makefile to build
this file only if SYSRESET isn't enabled.
SYSRESET can be enabled when building SYSRESET_PSCI for instance on this
platform.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Add bindings for CPU. This will allow displaying correctly the crystal,
CPU and master clock.
Reported-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: a64862284f ("clk: at91: sam9x60: add support compatible with
CCF")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
With Device Manager firmware in an elf file form, we cannot load the FIT
image to the exact same address as any of the executable sections of the
elf file itself is located.
However, the device tree descriptions for the ARMV8 bootloader/OS
includes DDR regions only the final sections in DDR where the Device
Manager firmware is actually executing out of.
As the R5 uC is usually operating at a slower rate than an ARMv8 MPU,
by starting the Armv8 ahead of parsing the elf and copying the correct
sections to the required memories creates a race condition where the
ARMv8 could overwrite the elf image loaded from the FIT image prior to
the R5 completing parsing and putting the correct sections of elf in
the required memory locations. OR create rather obscure debug conditions
where data in the section is being modified by ARMV8 OS while the elf
copy is in progress.
To prevent all these conditions, lets make sure that the elf parse and
copy operations are completed ahead of ARMv8 being released to execute.
We will pay a penalty of elf copy time, but that is a valid tradeoff in
comparison to debug of alternate scenarios.
Signed-off-by: Nishanth Menon <nm@ti.com>
NB0 is bridge to SRAM and NB1 is bridge to DDR.
To ensure that SRAM transfers are not stalled due to delays during DDR
refreshes, SRAM traffic should be higher priority (threadmap=2) than
DDR traffic (threadmap=0).
This fixup is critical to provide deterministic access latency to
MSMC from ICSSG, it applies to all AM65 silicon revisions and is due
to incorrect reset values (has no erratum id) and statically setting
things up should be done independent of usecases and board.
This specific style of Northbridge configuration is specific only to
AM65x devices, follow-on K3 devices have different data prioritization
schemes (ASEL and the like) and hence the fixup applies purely to
AM65x.
Without this fix, ICSSG TX lock-ups due to delays in MSMC transfers in
case of SR1 devices, on SR2 devices, lockups were not observed so far
but high retry rates of ICSSG Ethernet (icssg-eth) and, thus, lower
throughput.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
[Jan: rebased, dropped used define, extended commit log]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
[Nishanth: Provide relevant context in the commit message]
Signed-off-by: Nishanth Menon<nm@ti.com>
The K3 SoCs have some PLL output clocks (POSTDIV clocks) which in
turn serve as inputs to other HSDIV output clocks. These clocks use
the actual value to compute the divider clock rate, and need to be
registered with the CLK_DIVIDER_ONE_BASED flags. The current k3-clk
driver and data lacks the infrastructure to pass in divider flags.
Update the driver and data to account for these divider flags.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Add a note to the automatically generated clk-data and dev-data files
for j721e and j7200 to indicate that they are in fact auto-generated and
should not be hand edited.
Also adjust TI URL to use https instead of http and also add an empty
line before first header inclusion.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The TI K3 Fractional PLLs use two programmable POSTDIV1 and POSTDIV2
divisors to generate the final FOUTPOSTDIV clock. These are in sequence
with POSTDIV2 following the POSTDIV1 clock. The current J7200 clock data
has the POSTDIV2 clock as the parent for the POSTDIV1 clock, which is
opposite of the actual implementation. Fix the data by simply adjusting
the register bit-shifts.
The Main PLL1 POSTDIV clocks were also defined incorrectly using Main PLL0
register values, fix these as well.
Fixes: 277729eaf3 ("arm: mach-k3: Add platform data for j721e and j7200")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The TI K3 Fractional PLLs use two programmable POSTDIV1 and POSTDIV2
divisors to generate the final FOUTPOSTDIV clock. These are in sequence
with POSTDIV2 following the POSTDIV1 clock. The current J721E clock data
has the POSTDIV2 clock as the parent for the POSTDIV1 clock, which is
opposite of the actual implementation. Fix the data by simply adjusting
the register bit-shifts.
The Main PLL1 POSTDIV clocks were also defined incorrectly using Main PLL0
register values, fix these as well.
Fixes: 277729eaf3 ("arm: mach-k3: Add platform data for j721e and j7200")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Add a weak release_resources_for_core_shutdown() stub implementation
that can be overridden by actual implementation if a SoC supports that
function.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Header file version.h does not use anything from timestamp.h. Including of
timestamp.h has side effect which cause recompiling object file at every
make run because timestamp.h changes at every run.
So remove timestamp.h from version.h and include timestamp.h in files
which needs it.
This change reduce recompilation time of final U-Boot binary when U-Boot
source files were not changed as less source files needs to be recompiled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add in lib/acpi/acpi_table.c and test/dm/acpi.c, rework a few others]
Signed-off-by: Tom Rini <trini@konsulko.com>
U_BOOT_DATE and U_BOOT_TIME are updated on every run of make command.
Therefore mrc.c file is recompiled every time when running make which means
that whole U-Boot binary is recompiled on every run of make command.
Simplify it and do not recompile U-Boot binary on every run of make command
by not depending on macros U_BOOT_DATE and U_BOOT_TIME.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
As explained by Wolfgang, historically PowerPC would do a number of
things to hand-optimize placement of the binary on NOR flash in order to
maximize utilization of very scarce resources. These days, we simply
aren't optimizing our binary layout for NOR flash placement and it's
quite likely this wasn't working as intended. Furthermore, this level
of optimization makes it difficult to have version_string be a global,
instead of a weak and overridden value, and so make more progress on
reproducible builds, which is a current concern.
Move to having PowerPC no longer store version_string in the early part
of text so that it might be part of the first page of NOR and instead
use the same declaration everyone else does.
Link: https://lore.kernel.org/r/96716.1629798400@gemini.denx.de/
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no need to overload version_string at the end of start.S files.
Common implementation of version_string should be fine.
Signed-off-by: Pali Rohár <pali@kernel.org>
[trini: Keep the align, it's important for the rest of linkage]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, there is no ENTRY() entry in the m68k linker script.
However, since they currently contain a version_string symbol, which
then overrides the default weak version_string symbol, the linker
decides we must keep start.o in the resulting link. Add an ENTRY() line
so that the linker will know to keep this, even when version_string is
no longer provided in start.S
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Tom Rini <trini@konsulko.com>
It is useful to map a file into memory so that it can be accessed using
simple pointers. Add a function to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to return the size of a file. This is useful in situations
where we need to allocate memory for it before reading it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Move the XHCI PCI device base up in the virtual address space. This fixes
initialization failure observed with newer Raspberry Pi firmware, later
than 63b1922311 ("firmware: arm_loader: Update armstubs with those from
PR 117). It looks that chosing 0xff800000 as the XHCI PCI device base
conflicts with the updated ARM/VideoCore firmware.
This also requires to reduce the size of the mapped PCI device region
from 8MiB to 4MiB to fit into 32bit address space. This is still enough
for the XHCI PCI device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
At present SMBIOS tables are empty, which breaks some use-cases that
rely on that. Add some minimal information to fulfill this.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Note that we have to add CONFIG_SPIFLASH to scripts/config_whitelist.txt
because it's not really migrated at this point.
Acked-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Acked-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Acked-by: Oleksandr Zhadan and Michael Durrant <arcsupport@arcturusnetworks.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Handle CONFIG_SPIFLASH differently and delete Kconfig file]
Signed-off-by: Tom Rini <trini@konsulko.com>
In the cdns3 usb driver, the clock name looked for is ref. Therefore, fix
the clock-names property in usb0 instance for proper initialization of
cdns3 usb gadget driver.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
As per Device Tree Specification [1], the status parameter of nodes can
be "okay", "disabled", etc. "ok" is not a valid parameter.
U-boot Driver Model does not recognize status="ok" either and treats
the node as disabled.
[1] https://github.com/devicetree-org/devicetree-specification/releases/tag/v0.3
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Add u-boot,dm-spl tag in the pinmux device tree node, required for MMCSD1
subsystem.
Fixes: b6059ddc45 ("arm: dts: k3-am642: Add r5 specific dt support")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
USB nodes were mistakenly disabled in
commit 942853dd96 ("arm: dts: Resync BeagleBone device trees")
This commit is to fix the following issue:
starting USB...
No working controllers found
USB is stopped. Please issue 'usb start' first.
starting USB...
No working controllers found
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=0782e8572ce43f521ed6ff15e4a7ab9aa5acdc85
Fixes: 942853dd96 ("arm: dts: Resync BeagleBone device trees")
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Paul Barker <paul.barker@sancloud.com>
Since mvpp2 is using the new mdio driver and the cp110 has been
synced with the linux upstream, the mdio has to enabled in the
device tree file.
This is missing for some device tree files and therefore the
network cards do not come online.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Reviewed-by: Stefan Roese <sr@denx.de>
SHA512_ALGO was used as a "either SHA512 or SHA384", although the
implementations of these two algorithms share a majority of code.
From a Kconfig interface perspective, it makes sense to present two
distinct options. This requires #ifdefing out the SHA512
implementation from sha512.c. The latter doesn't make any sense.
It's reasonable to say in Kconfig that SHA384 depends on SHA512, and
seems to be the more polite way to handle the selection.
Thus, automatically select SHA512 when SHA384 is enabled.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
No iMX platforms have supported ATAG-based booting. They have however
re-used the CONFIG_SERIAL_TAG option as a way to enable support of
reading the OTP fuses and setting the serial# environment variable in
some cases. Change the warp7 support to use this symbol, use this for
updating the rest of the imx7 code, and update the imx8 conditionals.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
We usually use a space in function declaration, rather than a tab.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Invokes the common cache_init function to initialize ccache.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The enable_caches is a generic hook for architecture-implemented, we
define this function to enable composable cache of sifive platforms.
In sifive_cache, it invokes the generic cache_enable interface of cache
uclass to execute the relative implementation in SiFive ccache driver.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The enable_caches is a generic hook for architecture-implemented, we
leverage this function to enable caches for RISC-V
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To make analyzing exceptions easier output the code that leads to it.
We already do the same on the ARM platform.
Here is an example:
=> exception ebreak
Unhandled exception: Breakpoint
EPC: 000000008ff5d50e RA: 000000008ff5d62c TVAL: 0000000000000000
EPC: 000000008020b50e RA: 000000008020b62c reloc adjusted
Code: 2785 0693 07a0 dce3 fef6 47a5 d563 00e7 (9002)
To disassemble the code we can use the decodecode script:
$ echo 'Code: 2785 0693 07a0 dce3 fef6 47a5 d563 00e7 (9002)' | \
CROSS_COMPILE=riscv64-linux-gnu- scripts/decodecode
Code: 2785 0693 07a0 dce3 fef6 47a5 d563 00e7 (9002)
All code
========
0: 2785 addiw a5,a5,1
2: 07a00693 li a3,122
6: fef6dce3 bge a3,a5,0xfffffffffffffffe
a: 47a5 li a5,9
c: 00e7d563 bge a5,a4,0x16
10:* 9002 ebreak <-- trapping instruction
...
Code starting with the faulting instruction
===========================================
0: 9002 ebreak
...
As it is not always clear if the first 16 bits are at the start or in the
middle of a 32bit instruction it may become necessary to strip the first
u16 from the output before calling decodecode to get the correct
disassembled code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
When booting in EFI, lib/efi_loader/efi_memory.c calls
board_get_usable_ram_top(0) which returns by default
gd->ram_base + gd->ram_size which is the top of DDR.
In case of OPTEE boot, the top of DDR is currently reserved by OPTEE,
board_get_usable_ram_top(0) must return an address outside OPTEE
reserved memory.
gd->ram_top matches this constraint as it has already been initialized
by substracting all DT reserved-memory (included OPTEE memory area).
Fixes: 92b611e8b0 ("stm32mp: correctly handle board_get_usable_ram_top(0)")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
Per a request from Andre Przywara and agreed with by Peter Hoyes, the
vexpress aemv8r support wasn't quite ready to be merged, but the
discussion had moved off list. We should keep the first patch in the
series for now, but revert the rest. This reverts the following
commits:
e0bd6f31ce doc: Add documentation for the Arm vexpress board configs
30e5a449e8 arm: Use armv8_switch_to_el1 env to switch to EL1
b53bbca63b vexpress64: Add BASER_FVP vexpress board variant
2f5b7b7490 armv8: Add ARMv8 MPU configuration logic
37a757e227 armv8: Ensure EL1&0 VMSA is enabled
Signed-off-by: Tom Rini <trini@konsulko.com>
The prototype of psci_features() duplicated. Remove extra declaration.
Fixed: e21e3ffdd1 ("psci: Fix warnings when compiling with W=1")
Reported-by: Michael Scott <mike@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
For ARMv8-A, NEON is standard, so the compiler can use it even when no
special target flags are provided. For example, it can use stores from
NEON registers to zero-initialize large structures. GCC 11 decides to
do this inside the DRAM init code for the Allwinner H6.
However, GCC 11 has a bug where it generates misaligned NEON register
stores even with -mstrict-align. Since the MMU is not enabled this early
in SPL, the misaligned store causes an exception and breaks booting.
Work around this issue by restricting the compiler to using GPRs only,
not vector registers. This prevents any future surprises relating to
NEON use as well.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Use the environment variable armv8_switch_to_el1 to determine whether
to switch to EL1 at runtime. This is an alternative to the
CONFIG_ARMV8_SWITCH_TO_EL1 compile-time option.
The environment variable will be ineffective if the ARMV8_MULTIENTRY
config is used.
This is required by the Armv8r64 architecture, which must be able to
boot at S-EL1 for Linux but may need to boot at other ELs for other
systems.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
The BASER_FVP board variant is implemented on top of the BASE_FVP board
config (which, in turn, is based on the Juno Versatile Express board
config). They all share a similar memory map - for BASER_FVP the map is
inverted from the BASE_FVP
(https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map)
* Create new TARGET_VEXPRESS64_BASER_FVP target, which uses the same
board config as BASE_FVP and JUNO
* Adapt vexpress_aemv8a.h header file to support BASER_FVP (and rename
to vexpress_aemv8.h)
* Enable config to switch to EL1 for the BASER_FVP
* Create vexpress_aemv8r defconfig
* Provide an MPU memory map for the BASER_FVP
For now, only single core boot is supported.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[trini: Add MAINTAINERS, move BOOTCOMMAND to defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Armv8r64 is the first Armv8 platform that only has a PMSA at the
current exception level. The architecture supplement for Armv8r64
describes new fields in ID_AA64MMFR0_EL1 which can be used to detect
whether a VMSA or PMSA is present. These fields are RES0 on Armv8a.
Add logic to read these fields and, for the protection of the memory
used by U-Boot, initialize the MPU instead of the MMU during init, then
clear the MPU regions before transition to the next stage.
Provide a default (blank) MPU memory map, which can be overridden by
board configurations.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
On Armv8-R, the EL1&0 memory system architecture is configurable as a
VMSA or PMSA, and resets to an "architecturally unknown" value.
Add code to armv8_switch_to_el1_m which detects whether the MSA at
EL1&0 is configurable using the id_aa64mmfr0_el1 register MSA fields.
If it is we must ensure the VMSA is enabled so that a rich OS can boot.
The MSA and MSA_FRAC fields are described in the Armv8-R architecture
profile supplement (section G1.3.7):
https://developer.arm.com/documentation/ddi0600/latest/
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
The use of ARMv8.3 pointer authentication (PAuth) is governed by fields
in HCR_EL2, which trigger a 'trap to EL2' if not enabled. The reset
value of these fields is 'architecturally unknown' so we must ensure
that the fields are enabled (to disable the traps) if we are entering
the kernel at EL1.
The APK field disables PAuth instruction traps and the API field
disables PAuth register traps
Add code to disable the traps in armv8_switch_to_el1_m. Prior to doing
so, it checks fields in the ID_AA64ISAR1_EL1 register to ensure pointer
authentication is supported by the hardware.
The runtime checks require a second temporary register, so add this to
the EL1 transition macro signature and update 2 call sites.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
The logic in msm_generate_mac_addr() was originally taken from the LK
bootloader where the serial number is a string and must be parsed first.
However, in U-Boot msm_board_serial() returns an u32 and
msm_generate_mac_addr() has quite complicated code that will first
print it as a hex string and then immediately parse it again.
What this function actually does at the end is to put the serial number
encoded as big endian (the order used for the hex string) into the u8 *mac.
Use put_unaligned_be32() to do that with bit shifts instead of going
through the string format.
This should be slightly more efficient and cleaner but does not result
in any functional difference.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
At the moment U-Boot produces an empty MAC address (02:00:00:00:00:00)
if the eMMC is not used by anything in U-Boot (e.g. with
CONFIG_ENV_IS_NOWHERE=y instead of having the environment on eMMC).
This happens because then there is nothing that actually initializes
the eMMC and reads the "cid" that is later accessed.
To fix this, call mmc_init() to ensure the eMMC is initialized.
There is no functional difference if the eMMC is already initialized
since then mmc_init() will just return without doing anything.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
A U-Boot image could be loaded and executed at a different
location than it was linked at.
For example, Aspeed takes a stable release version of U-Boot image
as the golden one for recovery purposes. When the primary storage
such as flash is corrupted, the golden image would be loaded to any
SRAM/DRAM address on demands through ethernet/UART/etc and run for
rescue.
To deal with this condition, the PIE is needed as there is only one
signed, golden image, which could be however executed at different
places.
This patch adds the PIE support for ARMv7 platform.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Enabling CONFIG_SYS_THUMB_BUILD produces a significantly smaller
U-Boot binary (250 KiB vs 320 KiB) that still seems to be fully
functional. Make use of that by default but keep it as "imply" so it
can be disabled for testing in case this causes trouble for someone.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Over the time, the "stemmy" U-Boot board was tested on several other
Samsung smartphones based on ST-Ericsson NovaThor Ux500. Convert the
documentation to reStructuredText at doc/board/ste/stemmy.rst and
make the device list complete. Also note that the board now boots
into USB Fastboot instead of just ending up at the U-Boot prompt.
The device table is mostly taken from the postmarketOS wiki article
(https://wiki.postmarketos.org/wiki/ST-Ericsson_NovaThor_U8500).
All the newly added devices were tested by Linus Walleij.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Make use of the new drivers for ARM U8500 introduced in the U-Boot
2021.10 merge window by adding basic support for USB Fastboot with
the "stemmy" board. As a first step this will always boot directly
into USB Fastboot for now with the console displayed on the screen
to make that obvious.
Samsung uses quite strange GPT partition labels on these boards,
so also add a bunch of fastboot_partition_alias_* to make this more
easy to use.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
So far there is no need for a clock driver in U-Boot because the
previous boot stage leaves all the necessary clocks on. However,
some drivers in U-Boot (e.g. arm_pl180_mmci) depend on having a clock
driver to obtain the clock frequency.
Setting up the clock drivers properly is a bit tricky on U8500,
so for now add a simple fixed-clock for the eMMC that allows obtaining
the clock frequency. This should be replaced eventually if some board
actually requires enabling some of the clocks.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Update ste-dbx5x0.dtsi, ste-ab8500.dtsi and ste-ab8505.dtsi with
the changes made in upstream Linux. They are taken from
https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik.git/
branch "ux500-dts-for-v5.15" (pending merge for Linux 5.15).
The only relevant change for U-Boot here is
"ARM: dts: ux500: ab8500: Link USB PHY to USB controller node" [1]
which links the USB PHY to the USB controller. This is necessary on
U-Boot because the PHY driver is implemented as part of the generic
PHY subsystem that makes use of these bindings.
[1]: https://lore.kernel.org/linux-arm-kernel/20210709182234.47232-1-stephan@gerhold.net/
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Imply the options for new drivers added for ARM U8500 during the
U-Boot 2021.10 merge window. Adding these as "imply" in the Kconfig
avoids having to add them to all the board defconfigs but still allows
disabling them if wanted.
Also select DM_USB_GADGET if DM_USB is selected because otherwise
the Ux500 MUSB glue driver does not show up in the configuration.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Move the function get_boot_device() from spl.c to cpu.c.
Make it visible, so that it may be used from other files.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
File mach/soc.h is included also in 64-bit mvebu processors, so define
Armada XP related macros only when compiling for Armada XP.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
We move the SYS_CACHE_SHIFT_N options from arch/arm/Kconfig to
arch/Kconfig, and introduce SYS_CACHE_SHIFT_4 to provide a size of 16.
Introduce select statements for other architectures based on current
usage. For MIPS, we take the existing arch-specific symbol and migrate
to the generic symbol. This lets us remove a little bit of otherwise
unused code.
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Leo <ycliang@andestech.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
- Provide a default Kconfig value of the default script
- Largely continue to define this via the board Kconfig file
- For the boards that select a script based on defconfig rather than
TARGET, keep this within the defconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, there is no over-arching symbol for access to
arch/arm/mach-imx nor the CONFIG symbols that are common over all of
these related platforms. This new CONFIG symbol will allow us to start
down this path.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Guard most of the options in drivers/ddr/fsl/Kconfig with
SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this symbol can either be a fixed value or the function
get_board_ddr_clk, migration is tricky. Introduce a choice of DYNAMIC
or STATIC_DDR_CLK_FREQ. If DYNAMIC, we continue to use the board
defined get_board_ddr_clk function. If STATIC, set CONFIG_DDR_CLK_FREQ
to that value and now include/clock_legacy.h contains the function
prototype or defines get_board_ddr_clk() to that static value. Update
callers to test for DYNAMIC or STATIC.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the symbol that controls building some JEDEC SPD support functions
to Kconfig. This is required on the TI keystone 2 platforms and very
frequently (but not always) used on large number of Freescale/NXP
platforms, so use imply there.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move CONFIG_DDR_32BIT/64BIT to Kconfig as a choice for Armada XP
platforms. Make 64bit the default as this mirrors the current code.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Check that the watchdog_reset() implementation in wdt-uclass behaves
as expected:
- resets all activated watchdog devices
- leaves unactivated/stopped devices alone
- that the rate-limiting works, with a per-device threshold
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
It seems that no other test has claimed gpio_a:7 yet, so use that.
The only small wrinkle is modifying the existing wdt test to use
uclass_get_device_by_driver() since we now have two UCLASS_WDT
instances in play, so it's a little more robust to fetch the device by
driver and not merely uclass+index.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
These symbols are now either unused or were only used within the config
file to determine other logic, which could be done in a way that doesn't
further pollute the CONFIG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
While the Kconfig language seems to accept either form of whitespace, we
use a space throughout the project, except in these spots.
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate CONFIG_GICV2 and CONFIG_GICV3 to Kconfig. We still have the GIC
related registers that need to be handled more cleanly but start by
moving this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Migrate SYS_I2C_SH and related defines to Kconfig
- Remove currently unused SYS_I2C_SH related defines
- Cleanup related README section.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_MXC
CONFIG_SYS_I2C_MXC_I2C1
CONFIG_SYS_I2C_MXC_I2C2
CONFIG_SYS_I2C_MXC_I2C3
CONFIG_SYS_I2C_MXC_I2C4
Signed-off-by: Tom Rini <trini@konsulko.com>
The omap24xx I2C driver uses its own CONFIG namespace for common I2C
variables. Rather than convert more of them to Kconfig, rename these to
the common I2C ones and remove the entirely unused functionality. As
part of this, we make the am335x_shc platforms consistent with their
intended speed values.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert SYS_I2C_EARLY_INIT to Kconfig, and make it depend on
SPL_SYS_I2C_LEGACY. Remove the weak implementation as it's either
something that needs to exist for real, or shouldn't be called.
Signed-off-by: Tom Rini <trini@konsulko.com>
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Signed-off-by: Tom Rini <trini@konsulko.com>
Looking over the current boards, there are no users of
CONFIG_MAC_ADDR_IN_EEPROM. Further, omapl138_lcdk uses
CONFIG_NET_RANDOM_ETHADDR. Drop various unused code paths.
Cc: Adam Ford <aford173@gmail.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYSilpgAKCRDKSWXLKUoM
Id2JAJ9jY19JiEpOd3vuRCT5CE/pzX4yDACeP8DiXDzSi5tLHwDWUCBobUTze2s=
=5lnj
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.10-rc3
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
Use TF-A instead of ATF in description. And update generic description with
removing ATF because also configurations without it are supported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot support board detection at run time and based on it change DT.
This feature is implemented for SOM Kria platforms which contain two
eeproms which contain information about SOM module and CC (Carrier card).
Full U-Boot starts with minimal DT file defined by
CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image.
It is using default setup of board_name variable initializaed to
DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option.
When DTB_RESELECT is enabled board_detection() is called. Keep it your mind
that this code is called before relocation. board_detection() is calling
xilinx_read_eeprom() which fills board_info (xilinx_board_description)
structure which are parsed in board_name_decode().
Based on DT configuration and amount of nvmemX aliases name of the board is
composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev"
<board_revision> "-" <cc_name> "-rev" <cc_revision>.
If CC is not present or more are available it keeps going.
When board name is composed and returned from board_name_decode() it is
assigned to board_name variable which is used by
board_fit_config_name_match() which is called via fdtdec_setup() when it
goes over config options in multi dtb FIT image.
From practical point of view multi DTB image is key point here which has to
contain configs for detected combinations. Unfortunately as of now they
have to be full DTBs and DTBOs are not supported.
That's why configuration like:
config_X {
description = "zynqmp-board-cc";
fdt = "board", "cc";
};
needs to be squashed together with:
fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \
arch/arm/dts/zynqmp-cc.dtbo
and only one dtb is in fit:
config_X {
description = "zynqmp-board-cc";
fdt = "board-cc";
};
For creating multi DTBs fit image use mkimage -E, e.g.:
mkimage -E -f all.its all.dtb
When DTB_RESELECT is enabled xilinx_read_eeprom() is called before
relocation and it uses calloc for getting a buffer. Because this is dynamic
memory it is not relocated that's why xilinx_read_eeprom() is called again
as the part of board_init(). This second read with calloc buffer placed in
proper position board_late_init_xilinx() can setup u-boot variables as
before.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When MULTI_DTB_FIT is enabled fit-dtb.blob fit image is created which
contain all DTBs listed by CONFIG_OF_LIST. And with DTB_RELESELECT there is
a need to handle it as one file with DTBs in it not as separate DTBs in
u-boot.its/itb.
That's why extend mkimage_fit_atf.sh to generate u-boot.itb correctly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Start of DTB should be 64bit aligned that's why also make sure that end is
also 64bit aligned. It is not required but it is nice thing to do.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
soc_xilinx_versal driver allows identification of family & revision
of versal SoC. This driver is selected by CONFIG_SOC_XILINX_VERSAL.
Probe this driver using platdata U_BOOT_DEVICE structure which is
defined at mach-versal/cpu.c.
Add this config to xilinx_versal_virt_defconfig &
xilinx_versal_mini_ospi_defconfig file to select this driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
soc_xilinx_zynqmp driver allows identification of family & revision
of zynqmp SoC. This driver is selected by CONFIG_SOC_XILINX_ZYNQMP.
Add this config to xilinx_zynqmp_virt_defconfig file.
Probe this driver using platdata U_BOOT_DEVICE structure which is
specified in mach-zynqmp/cpu.c.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace 'io-standard' property with 'power-source' property in all
zynq dts files to be in sync with Zynq Pinctrl driver.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add device tree for N5X.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <lftan.linux@gmail.com>
The DDR subsystem in Diamond Mesa is consisted of controller, PHY,
memory reset manager and memory clock manager.
Configuration settings of controller, PHY and memory reset manager
is come from DDR handoff data in bitstream, which contain the register
base addresses and user settings from tool.
Configuration settings of memory clock manager is come from the HPS
handoff data in bitstream, however the register base address is defined
in device tree.
The calibration is fully done in HPS, which requires IMEM and DMEM
binaries loading to PHY SRAM for running this calibration, both
IMEM and DMEM binaries are also part of bitstream, this bitstream
would be loaded to OCRAM by SDM, and configured by DDR driver.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Move cm_get_mpu_clk_hz function declaration from individual device's
clock manager header file to common clock_manager.h.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
There is a QSPI NOR flash part on the board. Because this chip isn't
yet supported in Linux, but it is supported in U-Boot, and the
face that the RPC_SPI compatible names are different in U-Boot and
Linux, the device tree updates are confined to -u-boot.dtsi files.
In order to use the QSPI, TF-A must leave RPC unlocked by compiling
TF-A with RZG_RPC_HYPERFLASH_LOCKED=0.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Biju Bas <biju.das.jz@bp.renesas.com>
N5X support both HPS handoff data and DDR handoff data.
Existing HPS handoff functions are restructured to support both existing
devices and N5X device.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Rename to common file name to used by all SOC64 devices and change
"_S10_" to "_SOC64_" in base_addr_soc64.h.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Move 'linux_qspi_enable' from bootcommand to board_prep_linux function when
OS booted from FIT image for Stratix 10 and Agilex. This flow is common for
all Intel SOC64 devices.
U-Boot will update 'fdt_addr' environment value based on FIT image in
board_prep_linux function, and 'linux_qspi_enable' will refer to 'fdt_addr'
environment value to retrieve the device tree node.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Documentation:
* Rename Freescale to NXP
* Document structures used for the UEFI TCG2 protocol
UEFI:
* Device paths must use EfiBootServicesData
-----BEGIN PGP SIGNATURE-----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=gMKg
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-10-rc3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-10-rc3
Documentation:
* Rename Freescale to NXP
* Document structures used for the UEFI TCG2 protocol
UEFI:
* Device paths must use EfiBootServicesData
fsl-qoriq: Fixes related to env, spi, usb, crypto, configs, distro-boot
for Layerscape Boards like lx2, sl28, ls2088ardb.
powerpc: Fixes for t208xrdb revd board and cortina related configs
update for T208xRDB, T4240RDB.
The driver will use a syscon regmap as backend and supports both
16 and 32 size value. The value will be stored in the CPU's endianness.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
NXP platforms expect custom bootcmd and mcinitcmd to be
updated as per boot source with default environment.
Check env variable fsl_bootcmd_mcinitcmd_set to prepare
bootcmd and mcinitcmd
Fixes: cbf77d2018 (armv8: fsl-layerscape: Fix automatic
setting of bootmcd with TF-A)
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board doesn't use the MTD subsystem in u-boot, thus there is no
need to specify the partitions. They are outdated anyway. Just drop
them.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This symbol was largely migrated, except for one case. Update it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The STM32MP ROM provides several service. One of them is the ability
to verify ecdsa256 signatures. Hook the ROM API into the ECDSA uclass.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.
There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex for SPL, so opt for the second option. This incurs 20ms delay
during boot, when SPL loads U-Boot to DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Device tree alignment with Linux kernel v5.14-rc3
- ARM: dts: stm32: move stmmac axi config in ethernet node on stm32mp15
- ARM: dts: stm32: Configure qspi's mdma transfer to block for stm32mp151
- ARM: dts: stm32: add a new DCMI pins group on stm32mp15
- ARM: dts: stm32: fix ltdc pinctrl on microdev2.0-of7
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The function board_get_usable_ram_top can be called after relocation
with total_size = 0 to get the uppermost pointer that is valid to access
in U-Boot.
When total_size = 0, the reserved memory should be not take in account
with lmb library and 'gd->ram_base + gd->ram_size' can be used.
It is the case today in lib/efi_loader/efi_memory.c:efi_add_known_memory()
and this patch avoids that the reserved memory for OP-TEE is not part of
the EFI available memory regions.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The MTD tee partitions used to save the OP-TEE binary are needed when
TF-A doesn't use the FIP container to load binaries.
This patch puts under CONFIG_STM32MP15x_STM32IMAGE flag the associated
code in U-Boot binary and prepare the code cleanup when
CONFIG_STM32MP15x_STM32IMAGE support will be removed after TF-A migration
to FIP support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add TF-A FIP support for trusted boot on STM32MP15x,
when STM32MP15x_STM32IMAGE is not activated.
With FIP support the SSBL partition is named "fip" and its size is 4MB,
so the ENV partition name in device tree (for SD card or eMMC)
or offset in defconfig (CONFIG_ENV_OFFSET / CONFIG_ENV_OFFSET_REDUND)
need to be modified.
With FIP the TEE MTD partitions are removed because the OP-TEE binray are
included in the FIP containers.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
With FIP support in TF-A (when CONFIG_STM32MP15x_STM32IMAGE
is not activated), the DT nodes needed by OP-TEE are added by OP-TEE
firmware in U-Boot device tree, present in FIP.
These nodes are only required in trusted boot, when TF-A load the file
u-boot.stm32, including the U-Boot device tree with STM32IMAGE header,
in this case OP-TEE can't update the U-Boot device tree.
Moreover in trusted boot mode with FIP, as the OP-TEE nodes are present
in U-Boot device tree only when needed the function
stm32_fdt_disable_optee can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
By default for trusted boot with TF-A, U-Boot (u-boot-nodtb)
is located in FIP container with its device tree and with
the secure monitor (provided by TF-A or OP-TEE).
The FIP file is loaded by TF-A BL2 and each components is
extracted at the final location.
This patch add CONFIG_STM32MP15x_STM32IMAGE to request the
STM32 image generation for SOC STM32MP15x
when FIP container is not used (u-boot.stm32 is loaded by TF-A
as done previously to keep the backward compatibility).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the Linux magic to the EFI file header to allow running our test
programs with GRUB's linux command.
MajorImageVersion = 1 indicates a kernel that can consume the
EFI_LOAD_FILE2_PROTOCOL. This allows to dump the GRUB provided intird with
our initrddump.efi tool.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The Odroid Go Advance uses a Rockchip Serial Flash Controller with an
XT25F128B SPI NOR flash chip. This adds support for both. Note that
while both the controller and chip support quad mode, only two lines
are connected to the chip. Changing the pinctrl to bus2 and setting tx
and rx lines to 2 for this reason.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the serial flash controller to the devicetree for the PX30.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support for setting the correct pin configuration
for the Rockchip Serial Flash Controller found on the PX30.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently there are a few arm32 rockchip board configs that don't
generate u-boot-rockchip.bin when running make because CONFIG_BINMAN
is not enabled. This patch changes CONFIG_ARCH_ROCKCHIP to also select
CONFIG_BINMAN if CONFIG_SPL and !CONFIG_ARM64.
Example builds that don't generate u-boot-rockchip.bin without this
patch:
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make kylin-rk3036_defconfig
make
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make rock_defconfig
make
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make tinker-rk3288_defconfig
make
Signed-off-by: Johan Gunnarsson <johan.gunnarsson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the rk3368 DTs and associated bits from 5.14-rc1.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the rk3328 DTs and associated bits from 5.14-rc1.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the rk3399 DTs and associated bits from 5.14-rc1.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
(Remove the conflict content for vmarc-som)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
- Convert GoFlex Home Ethernet and SATA to Driver Model (Tony)
- mvebu: Automatically detect CONFIG_SYS_TCLK (Pavel)
- mvebu: sata_mv: Fix HDD identication during cold start (Tony)
- a37xx: pci: Fix handling PIO config error responses (Pavel)
- Other minor misc changes and board maintainer updates
- sei610 & meson64_android cleanups to prepare android 11 boot support
- use Android BCB mechanism for reboot reason instead of HW reboot flag
- Switch meson64_android boot flow to use abootimg for A/B, AVB and DTBO support
-----BEGIN PGP SIGNATURE-----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=RZ8+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20210810' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- odroid-n2: fix fdtfile suffix for n2-plus
- sei610 & meson64_android cleanups to prepare android 11 boot support
- use Android BCB mechanism for reboot reason instead of HW reboot flag
- Switch meson64_android boot flow to use abootimg for A/B, AVB and DTBO support
Remove the recommended MAC address from the network card.
NanoPi R4S has a EEPROM attached to the 2nd I2C bus (U92), which stores the MAC address.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The host-index-min property is invalid,
so it inherits from the sdmmc definition in dtsi.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Correct the LEDS label name and remove the board type prefix,
which is actually unnecessary here, removes the redefined system status LED pin.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-radxarock-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. This file has recently had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3xxx-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Problem: board_spl_was_booted_from return wrong boot_devices[3] value
/spi@ff1d0000 and same-as-spl dont work properly for SPINOR flash
because arch/arm/mach-rockchip/spl-boot-order.c spl_node_to_boot_device
need parse SPINOR flash node as UCLASS_SPI_FLASH
spl-boot-order: same-as-spl > *** BOOT_SOURCE_ID 3 (2:emmc 3:spi 5:sd ...
/spi@ff1d0000 > board_boot_order: could not map node @618 to a boot-device
/sdhci@fe330000 > /mmc@fe320000
Solution: just change it to /spi@ff1d0000/flash@0
spl-boot-order: same-as-spl > *** BOOT_SOURCE_ID 3 (2:emmc 3:spi 5:sd ...
/spi@ff1d0000/flash@0 > /sdhci@fe330000 > /mmc@fe320000
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
If ddr3_init() fails then DDR was not initialized and we cannot load and
execute U-Boot. We cannot continue, we cannot do anything in this case, so
hang.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Config option CONFIG_SYS_TCLK is set by kw88f6281.h and kw88f6192.h files
to correct SOC/platform value. So do not overwrite it in board config
include files.
Kirkwood 88F6180 and 88F6192 uses 166 MHz TCLK and Kirkwood 88F6281 uses
200 MHz TCLK.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu axp platform always uses fixed 250 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Now every #if-#else case of soc.h file defines CONFIG_SYS_TCLK, so remove
useless default CONFIG_SYS_TCLK value from the end of soc.h file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu msys platform always uses fixed 200 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Bit 20 in SAR register specifies if TCLK is running at 200 MHz or 166 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Bit 15 in SAR register specifies if TCLK is running at 200 MHz or 250 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When booting from boot part1/2, the image offset should be 0, but
ROM has a bug to return 0x8000. Has to workaround the issue before
ROM fix it.
Use a ROM function to know boot from emmc boot part or user part
So we can set the image offset accordingly.
Signed-off-by: Ye Li <ye.li@nxp.com>
Since CMC1 MR0 only reflects high 16 bits boot cfg used for AP domian,
it does not connect to low 16 bits for RTD. So we can't get the correct
boot mode.
Change to use DGO_GP5 of SEC_SIM which is set by ROM.
Signed-off-by: Ye Li <ye.li@nxp.com>
The CMC1 SRS reflects the current reset cause, not SSRS.
Then you could get "Reset cause: WARM-WDG" when issue reset in U-Boot.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Need probe the S400 MU device in arch_cpu_init_dm, so we can use
S400 API in u-boot
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Rlease LPAV from RTD to APD
Release gpu2D/3D to APD
Set TRDC MBC2 MEM1 for iomuxc0 access
Since upower depends AP/M33 SW to configure IOMUX for its PMIC i2c
and MODE pins. we have to open iomuxc0 access for A35 core (domain 7)
in single boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
There is xrdc inside i.MX8ULP, we need to configure permission to make
sure AP non-secure world could access the resources.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since S400 will set the memory of SPL image to R/X. We can't write
to any data in SPL image.
1. Set the parameters save/restore only for u-boot, not for SPL. to
avoid write data.
2. Not use MU DM driver but directly call MU API to send release XRDC
to S400 at early phase.
3. Configure the SPL image memory of SRAM2 to writable (R/W/X)
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because we have set reset vector to ATF in SPL, have to set it back
to ROM for any reset in u-boot
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SRAM2 is half L2 cache and default to SRAM after system boot.
To enable the full l2 cache (512KB), it needs to reset A35 to make
the change happen.
So re-implement the jump entry function in SPL:
1. configure the core0 reset vector to entry (ATF)
2. enable the L2 full cache
3. reset A35
So when core0 up, it runs into ATF. And we have 512KB L2 cache working.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8ULP support using ROM API to load container image,
it use same ROM API as i.MX8MN/MP, and use same container format
as i.MX8QM/QXP.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since the container is shared among i.MX platforms, move its header file
to mach-imx
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add basic i.MX8ULP support
For the MMU part, Using a simple way the calculate the MMU size to avoid
default heavy calcaulation. And align address and size in the table
settings to 2MB or 4GB as much as possible. So we can reduce the 4K page
allocations in MMU table which will spends much time in create the
page table
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped support for networking and splash screen as these need
to be properly converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add PCIe reset gpio to the Bx50v3 devicetree and get get rid of
CONFIG_PCIE_IMX_PERST_GPIO.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
Do the following to add support for it:
- add dts
- add PMIC config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Replace the deprecated 'tx-fifo-depth' and 'rx-fifo-depth' properties
not supported by U-Boot drivers/net/phy/dp83867.c with the proper
'ti,fifo-depth' property.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.
To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks Ventana boards have always had usb0=usbh1 and usb1=usbotg
because OTG is often subloaded on these boards and a bit in the EEPROM
which flagging that OTG is subloaded is used to remove the dt node via the
alias.
U-Boot DM_USB UMS requires the usb0 alias be assigned to the usbotg
so fix the usb0 alias in order for UMS to work.
Fixes 72c46327f0: ("imx: ventana: enable dm support for USB")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This reverts commit 2359fa7a87.
While the goal is valid and there is surely unused memory in that area,
we also have a lot of crucial things still located at the top-of-memory
while running lmb_alloc_base. Such things are the page table (tlb_addr),
relocated U-Boot and the active stack. Possibly more. So this patch was
premature, we will need relocations of those things first if we want to
use the range.
Fixes booting on the IOT2050, but likely also on other boards. It got
stuck on relocating the FDT - over the relocated U-Boot code.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Turn on PIE, so that the U-Boot binary can be started from any arbitrary
location in DRAM instead of a predefined fixed one. Note that this patch
is not setting SYS_TEXT_BASE=0x0 yet, since that triggers relocation bugs
in env code that are yet to be fixed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
We don't need this check anymore since when PCI is enabled, driver model
is always used.
Use CONFIG_PCI instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Correct macro usage)
Signed-off-by: Tom Rini <trini@konsulko.com>
Import the imx28-evk devicetree files from Linux kernel
version 5.11-rc7.
This is in preparation for converting the mx28evk_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
- Fixed broken ICH SPI driver in software sequencer mode
- Added "m25p,fast-read" to SPI flash node for x86 boards
- Drop ROM_NEEDS_BLOBS and BUILD_ROM for x86 ROM builds
- Define a default TSC timer frequency for all x86 boards
- x86 MTRR MSR programming codes bug fixes
- x86 "hob" command bug fixes
- Don't program MTRR for DRAM for FSP1
- Move INIT_PHASE_END_FIRMWARE to FSP2
- Use external graphics card by default on Intel Crown Bay
- tangier: Fix DMA controller IRQ polarity in CSRT
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Initialize 'igd' and 'sdvo' to NULL so that we just need to test
them against NULL later, to be compatible with that case that IGD
and SDVO devices were already in disabled state.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For FSP1, there is no such INIT_PHASE_END_FIRMWARE.
Move board_final_cleanup() to fsp2 directory.
Fixes: 7c73cea442 ("x86: Notify the FSP of the 'end firmware' event")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on chromebook_coral, chromebook_samus, chromebook_link, minnowmax
Tested-by: Simon Glass <sjg@chromium.org>
There are several outstanding issues as to why this does not apply
to FSP1:
* For FSP1, the system memory and reserved memory used by FSP are
already programmed in the MTRR by FSP.
* The 'mtrr_top' mistakenly includes TSEG memory range that has the
same RES_MEM_RESERVED resource type. Its address is programmed
and reported by FSP to be near the top of 4 GiB space, which is
not what we want for SDRAM.
* The call to mtrr_add_request() is not guaranteed to have its size
to be exactly the power of 2. This causes reserved bits of the
IA32_MTRR_PHYSMASK register to be written which generates #GP.
For FSP2, it seems this is necessary as without this, U-Boot boot
process on Chromebook Coral goes very slowly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on chromebook_coral, chromebook_samus, chromebook_link, minnowmax
Tested-by: Simon Glass <sjg@chromium.org>
The size parameter of mtrr_add_request() and mtrr_set_next_var()
shall be power of 2, otherwise the logic creates a mask that does
not meet the requirement of IA32_MTRR_PHYSMASK register.
Programming such a mask value to IA32_MTRR_PHYSMASK generates #GP.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on chromebook_coral, chromebook_samus, chromebook_link, minnowmax
Tested-by: Simon Glass <sjg@chromium.org>
At present mtrr_commit() programs the MTRR MSRs starting from
index 0, which may overwrite MSRs that were already programmed
by previous boot stage or FSP.
Switch to call mtrr_set_next_var() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on chromebook_coral, chromebook_samus, chromebook_link, minnowmax
Tested-by: Simon Glass <sjg@chromium.org>
Current mtrr_commit() logic assumes that MTRR MSRs are programmed
consecutively from index 0 to its maximum number, and whenever it
detects an unused one, it clears all other MTRRs starting from that
one. However this may not always be the case.
In fact, the clear is not much helpful because these MTRRs come out
of reset as disabled already. Drop the clear codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on chromebook_coral, chromebook_samus, chromebook_link, minnowmax
Tested-by: Simon Glass <sjg@chromium.org>
If for some reason, TSC timer frequency cannot be determined from
hardware, nor is it specified in the device tree, U-Boot will panic
resulting in endless reset during boot.
Let's define a default TSC timer frequency using the Kconfig value
CONFIG_X86_TSC_TIMER_FREQ (note: #include must be used instead of
/include/ otherwise the macro is not pre-processed).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently there are two places to specify the x86 TSC timer frequency
with one in Kconfig used for early timer and the other one in device
tree used when the frequency cannot be determined from hardware.
This may potentially create an inconsistent config where the 2 values
do not match. Let's use the one specified in Kconfig in the device
tree as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These 2 options are no longer needed as now binman is used to build
u-boot.rom.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
IRQ polarity in CSRT has the same definition as by ACPI specification
chapter 19.6.64 "Interrupt (Interrupt Resource Descriptor Macro)", i.e.
ActiveHigh is 0, and ActiveLow is 1. On Intel Tangier the DMA controller
IRQ polarity is ActiveHigh.
Note, in DSDT (see southcluster.asl) it's described correctly.
Fixes: 5e99fde34a ("x86: tangier: Populate CSRT for shared DMA controller")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Except ICH7 SPI, all SPI flashes connected to ICH9 / Fast SPI should
have "m25p,fast-read" property present in their DT nodes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present if we see 'ranges' property (with no value) we assume it is a
boolean, as per the devicetree spec.
But another node may define 'ranges' with a value, forcing us to widen it
to an int array. At present this is not supported and causes an error.
Fix this and add some test cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
The autoboot tests are a recent addition to U-Boot, providing much-needed
coverage in this area.
A side effect of the keyed autoboot test is that this feature is enabled
in sandbox always. This changes the autoboot prompt and confuses the
pytests. Some tests become slower, for example the vboot tests take about
27s now instead of 3s.
We don't actually need this feature enabled to be able to run the tests.
Add a switch to allow sandbox to turn it on and off as needed. Use this
in the one test that needs it.
Add a command-line flag in case this is desired in normal use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 25c8b9f298 ("test: add first autoboot unit tests")
Reviewed-by: Steffen Jaeckel <jaeckel-floss@eyet-services.de>
- Move the PSCI runtime code for H3/A23/A33 into SRAM
- Pick the environment from the actual MMC boot device (SD card vs.
eMMC)
- Plus a small improvement from Icenowy, just for good measure.
There are more Allwinner SoCs that do not have a SCP now.
When there's no SCP_ADDR macro defined, we can assume there's no SCP
available.
Drop the scp part of FIT description when SCP_ADDR does not exist.
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far for the H3, A23, and A33 SoCs, we use DRAM to hold the secure
monitor code (providing PSCI runtime services). And while those SoCs do
not have the secure SRAM B like older SoCs, there is enough (secure)
SRAM A2 to put the monitor code and data in there instead.
Follow the design of 64-bit SoCs and use the first part for the monitor,
and the last 16 KiB for the SCP firmware. With this change, the monitor
no longer needs to reserve a region in DRAM.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: amend commit message, fix R40 and V3s build]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that proper load and execution addresses are set in v1 kwbimage we
can use it for loading and booting U-Boot proper.
Use the new spl_parse_board_header() function to implement parsing the
kwbimage v1 header. Use information from this header to locate offset and
size of the U-Boot proper binary, instead of using the legacy U-Boot
header which is prepended to the U-Boot proper binary stored at fixed
offset. This has the advantage that we do not need to relay on legacy
U-Boot header anymore and therefore U-Boot proper binary can be stored at
any offset, as is the case when loading & booting U-Boot proper by
BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL
code anymore.
Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case
BootROM is used for loading and executing U-Boot proper. This reduces the
size of U-Boot's SPL image. By default these config options are enabled
and so BootROM loading is not used. In some cases BootROM reads from SPI
NOR at lower speed than U-Boot SPL. So people can decide whether they
want to have smaller SPL binary at the cost of slower boot.
Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO,
CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT,
CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and
CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply"
(which can be selectivelly turned off and causes booting via BootROM).
Options CONFIG_SYS_SPI_U_BOOT_OFFS,
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to
zero as they define the location where kwbimage header starts. It is the
location where BootROM expects start of the kwbimage from which it reads,
parses and executes SPL part. The same applies to option
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one.
Update all config files to set correct values of these options and set
CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot
proper starts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Current code uses hack in board_init_f() which calls return_to_bootrom()
to skip U-Boot SPL code and return back to BootROM to load U-Boot via
UART or from NAND.
This change migrates that hack from the board_init_f() function and
changes it to return BOOT_DEVICE_BOOTROM instead of returning to BootROM
directly, so that U-Boot's SPL framework is used for returning to
BootROM.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
U-Boot's SPL framework already has an API for loading U-Boot via
BootROM.
Implement the function board_return_to_bootrom() for mvebu SPL code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
This function does not return, so add the appropriate compiler flag.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Register r0 should be set to return value 0x0 - NO_ERR.
Set r0 with return value after all registers are restored from the
stack, so that the return value is always correct.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 944c7a3176 ("arm: mvebu: Add option to use UART xmodem protocol via kwboot")
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
With the introduction of a generic reboot flag implemented in commit
a362ce214f ("fastboot: Implement generic fastboot_set_reboot_flag"), we
no longer need the custom PSCI implementation to handle the reboot reason.
This reverts commit 9a34dedfae.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
At early U-Boot stage, before relocation, MMU is not yet configured
and disabled. DDR may not be configured with the correct memory
attributes (can be configured in MT_DEVICE instead of MT_MEMORY).
In this case, usage of memcpy_{from, to}io() may leads to synchronous
abort in AARCH64 in case the normal memory address is not 64Bits aligned.
To avoid such situation, forbid usage of normal memory cast to (u64 *) in
case MMU is not enabled.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: mark.kettenis@xs4all.nl
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Align reset_cpu function with the next prototypes in
sysreset.h or in cpu_func.h to solve compilation issue:
void reset_cpu(void);
This patch solves the prototype conflict when cpu_func.h is
included.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and
CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less
than a year away.
Also we want to have a CONFIG_I2C for U-Boot proper just like we have
CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules.
Rename this symbol so it is clear it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Khadas vim series: Use devicetree for SMBIOS settings
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Artem Lapkin <art@khadas.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the "/reserved-memory/optee" node to the SPL devicetree. The
purpose is to allow configuring TZC regions when booting OP-TEE.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
OP-TEE is very particular about how the TZC should be configured.
When booting an OP-TEE payload, an incorrect TZC configuration will
result in a panic.
Most information can be derived from the SPL devicetree. The only
information we don't have is the split between TZDRAM and shared
memory. This has to be hardcoded. The rest of the configuration is
fairly easy, and only requires 3 TZC regions. Configure them.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The purpose of this change is to allow configuring TrustZone (TZC)
memory permissions. For example, OP-TEE expects TZC regions to be
configured in a very particular way. The API presented here is
intended to allow exactly that.
UCLASS support is not implemented, because it would not be too useful.
Changing TZC permissions needs to be done with care, so as not to cut
off access to memory we are currently using. One place where we can
use this is at the end of SPL, right before jumping to OP-TEE.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Commit 500327e2ea ("ARM: dts: stm32mp1: DT alignment with Linux kernel v5.8-rc1")
renamed sdmmc2_d47_pins_b phandle to sdmmc2_d47_pins_c, but without updating
the AV96 DT which uses that phandle. Linux missed similar update as well and
it was only added in commit 1ad6e36ec266 ("ARM: dts: stm32: Fix sdmmc2 pins
on AV96") .
Update the AV96 DT pinmux phandle, otherwise eMMC 8bit mode does not work
and access to eMMC takes a very long time to fall back to 4bit mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When a push-button is released and PA13/PA14 are defined as input (high-Z)
the LED should not be active as the circuit is open but a small current
leak through PCB or push-button close the circuit and allows a small LED
bias giving erroneous level voltage.
So it is recommended to activate an internal pull-up in order to clearly
fix the voltage at PA13/PA14 when button is released and to wait
a short delay before to read the GPIO value only when the pull-up is
correctly configured.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When the TAMP register 20 have an invalid value (0x0 for example after
TAMPER error) the "boot_device" U-Boot env variable have no value and
no error is displayed in U-Boot log.
The STM32MP boot command bootcmd_stm32mp failed with strange trace:
"Boot over !"
and the next command in bootcmd_stm32mp failed with few indication:
if test ${boot_device} = serial || test ${boot_device} = usb;
then stm32prog ${boot_device} ${boot_instance};
As it is difficult to investigate, the current patch avoids this issue:
- change the debug message to error: "unexpected boot mode" is displayed
- display trace "Boot over invalid!" in bootcmd_stm32mp
- execute "run distro_bootcmd" to try all the possible target
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The MAIN R5FSS0 cluster and corresponding nodes are no longer required
to be enabled in R5 SPL after removing the support for booting any core
from this cluster on R5 SPL. So, remove these from the relevant dts
files.
This is essentially a revert of the additions done in commit 2984b82b3b
("arm: dts: k3-j721e-r5: Enable r5fss0 cluster in SPL").
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726211311.5977-5-s-anna@ti.com
The mach-k3 common code defined a weak start_non_linux_remote_cores()
function so that the proper implementation can be plugged in the
SoC-specific source files. This won't be needed anymore, so remove the
the common code.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726211311.5977-4-s-anna@ti.com
The common J7 specific start_non_linux_remote_cores() override function
implements the logic to load and boot the Main R5FSS Core0 from R5 SPL.
This won't be supported any more for either J721E or J7200 after the R5
SPL rearchitecture for the System Firmware split into TI Foundation
Security (TIFS) and Device Management (DM) firmwares. So, cleanup the
corresponding code and the related SPL env variables.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726211311.5977-3-s-anna@ti.com
The Main R5FSS Core0 on J721E SoCs is originally booted from R5 SPL
itself to achieve certain product-level early-boot metrics. This is
no longer supported after the R5 SPL re-architecture (support merged
for v2021.10-rc1). Move the booting of this core altogether from R5
SPL to A72 U-Boot.
The env variables are left as is for now, and will be cleaned up
in a subsequent patch.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726211311.5977-2-s-anna@ti.com
The default U-Boot environment variables and design are all set up to
have the MCU R5FSS cluster to be in Split-mode. This is the setting
in v2021.01 U-Boot and the dt nodes are synched with the kernel binding
property names in commit 468ec2f3ef ("remoteproc: k3_r5: Sync to
upstreamed kernel DT property names") merged in v2021.04-rc2.
The mode for the cluster got switched back to LockStep mode by mistake
in commit e497876343 ("arm: dts: k3-am65: Sync Linux v5.11-rc6 dts
into U-Boot") also in v2021.04-rc2. This throws the following warning
messages when early-booting the cores using default env variables,
k3_r5f_rproc r5f@41400000: Invalid op: Trying to start secondary core 2 in lockstep mode
Load Remote Processor 1 with data@addr=0x82000000 65268 bytes: Failed!
Fix this by switching back the cluster to the expected Split-mode.
Make this mode change in the u-boot specific dtsi file to avoid such
sync overrides in the future until the kernel dts is also switched to
Split-mode by default.
Fixes: e497876343 ("arm: dts: k3-am65: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726162213.28719-1-s-anna@ti.com
A Wilink wireless device is connected to MMCSD0 subsystem and is not
supported in U-Boot. Therefore, disable main_sdhci0 device tree node in
U-Boot.
If main_sdhci0 device tree node is disabled then the the index of
main_sdhci1 node becomes 0 which leads to break in boot flow. Therefore,
add an alias to fix the index to 1.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726152807.22991-3-a-govindraju@ti.com
Function spl_boot_mode() is called in common/spl/spl_mmc.c, to find the
boot mode for a given boot device. This function was renamed to
spl_mmc_boot_mode() by commit e97590654a.
Therefore, rename spl_boot_mode to spl_mmc_boot_mode.
Fixes: 57dba04afb ("arm: mach-k3: am642: Add support for boot device detection")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726152807.22991-2-a-govindraju@ti.com
Add u-boot tags for torrent serdes. This has properties specific to
u-boot on top of DT in v5.13 Linux Kernel.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-15-kishon@ti.com
Add default lane function for torrent serdes. This is in sync
with v5.13 Linux Kernel.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-14-kishon@ti.com
Add DT node for torrent serdes. This is in sync with v5.13 Linux Kernel.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-13-kishon@ti.com
Configure the parent clock of wiz3_pll0_refclk to the internal clock
required for USB3 to be functional and also remove "ti,usb2-only"
property as it now supports USB3 mode. This has properties specific to
u-boot on top of DT present in v5.13 of Linux Kernel.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-12-kishon@ti.com
This device tree is imported from Linux 5.13.1 and enabled via the
am335x board file and the am335x evm defconfig.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
These device trees are updated to match the versions in Linux 5.13.1.
The tick-timer entry in am335x-bone-common.dtsi is preserved.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
HS400 speed mode is now supported in J7200 SoC[1]. Therefore add
mmc-hs400-1_8v tag in sdhci0 device tree node.
Also update the delay values for various speed modes supported, based on
the revised january 2021 J7200 datasheet[2].
[1] - section 12.3.6.1.1 MMCSD Features, in
https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
(SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)
[2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
(SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210525093826.10390-3-a-govindraju@ti.com
Add a bus driver for this and use it to configure the bus parameters for
the Ethernet interface. Drop the old pre-driver-model code.
Switch over to use driver model for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
PHY initialization should be handled from Xilinx USB core as the
prerequisite register configurations are done here only.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The board zynqmp-zc1751-xm016-dc2 support only USB2.0.
This patch removes USB3.0 DT configuration for DC2 board.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Documentation:
provide Makefile documentation
SMBIOS:
generate BIOS release date based on UEFI version
improve error handling in SMBIOS table generation
UEFI:
correct handling of signed capsule if authentication if off
-----BEGIN PGP SIGNATURE-----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=n6EU
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-10-rc1-3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-10-rc1-3
Documentation:
provide Makefile documentation
SMBIOS:
generate BIOS release date based on UEFI version
improve error handling in SMBIOS table generation
UEFI:
correct handling of signed capsule if authentication if off
SMBIOS tables only support 32bit addresses. If we don't have memory here
handle the error gracefully:
* on x86_64 fail to start U-Boot
* during UEFI booting ignore the missing table
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
CNTFRQ_EL0 is only writable from the highest supported exception
level on the platform. For Armv8-A, this is typically EL3, but
technically EL2 and EL3 are optional so it may need to be
initialized at EL2 or EL1. For Armv8-R, the highest exception
level is always EL2.
This patch moves the initialization outside of the switch_el
block and uses a new macro branch_if_not_highest_el which
dynamically detects whether it is at the highest supported
exception level.
Linux's docs state that CNTFRQ_EL0 should be initialized by the
bootloader. If not set, the the U-Boot prompt countdown hangs.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
At the moment the U-Boot port for the DragonBoard 410c is designed
to be loaded as an Android boot image after Qualcomm's Little Kernel (LK)
bootloader. This is simple to set up but LK is redundant in this case,
since everything done by LK can be also done directly by U-Boot.
Dropping LK entirely has at least the following advantages:
- Easier installation/board code (no need for Android boot images)
- (Slightly) faster boot
- Boot directly in 64-bit without a round trip to 32-bit for LK
So far this was not possible yet because of unsolved problems:
1. Signing tool: The firmware expects a "signed" ELF image with extra
(Qualcomm-specific) ELF headers, usually used for secure boot.
The DragonBoard 410c does not have secure boot by default but the
extra ELF headers are still required.
2. PSCI bug: There seems to be a bug in the PSCI implementation
(part of the TrustZone/tz firmware) that causes all other CPU cores
to be started in 32-bit mode if LK is missing in the boot chain.
This causes Linux to hang early during boot.
There is a solution for both problems now:
1. qtestsign (https://github.com/msm8916-mainline/qtestsign)
can be used as a "signing" tool for U-Boot and other firmware.
2. A workaround for the "PSCI bug" is to execute the TZ syscall when
entering U-Boot. That way PSCI is made aware of the 64-bit switch
and starts all other CPU cores in 64-bit mode as well.
Simplify the dragonboard410c board by removing all the extra code that
is only used to build an Android boot image that can be loaded by LK.
This allows dropping the custom linker script, special image magic,
as well as most of the special build/installation instructions.
CONFIG_REMAKE_ELF is used to build a new ELF image that has both U-Boot
and the appended DTB combined. The resulting u-boot.elf can then be
passed to the "signing" tool (e.g. qtestsign).
The PSCI workaround is placed in the "boot0" hook that is enabled
with CONFIG_ENABLE_ARM_SOC_BOOT0_HOOK. The extra check for EL1 allows
compatibility with custom firmware that enters U-Boot in EL2 or EL3,
e.g. qhypstub (https://github.com/msm8916-mainline/qhypstub).
As a first step these changes apply only to DragonBoard410c.
Similar changes could likely also work for the DragonBoard 820c.
Note that removing LK wouldn't be possible that easily without a lot of
work already done three years ago by Ramon Fried. A lot of missing
initialization, pinctrl etc was already added back then even though
it was not strictly needed yet.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Add partition information to the spi-nor flash.
This is required for accessing NOR flash via mtdparts.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
RTC devices could provide battery-backed memory that can be used for
storing the reboot mode magic value.
Add a new reboot-mode back-end that uses RTC to store the reboot-mode
magic value. The driver also supports both endianness modes.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A use case for controlling the boot mode is when the user wants
to control the device boot by pushing a button without needing to
go in user-space.
Add a new backed for reboot mode where GPIOs are used to control the
reboot-mode. The driver is able to scan a predefined list of GPIOs
and return the magic value. Having the modes associated with
the magic value generated based on the GPIO values, allows the
reboot mode uclass to select the proper mode.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
minor test build fixes
sandbox fixes for SDL2 and running TPL
bloblist resize feature
binman multithreading
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmD41JkRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrea8+wgArpcRqyC2nCYtdDl1q/8mWQabct2rUJVt
rzIYzgyPgkRBLQjlE8xgEchzAPOuw0YzQnEz3T80wepBPIy53+QYXaqumd9iuhtm
B1x4r/GumqS4qgn9Pfqxabw2eP8DNbxClc14ExDx3zR1pUwp0DRvnYQV/w+W2RQp
nWFKDdhdnkxuXApiVc01RF/9I+IygstVl1TUklxlw9EGkdpirczIX5cP2lhW9rsV
Cm4fPz4V6AphiUQ4RpllossBNVHHlbVyKOtdGWe4CrERH8Zv8tIVRVeHCr0GydPr
ORhIZTk7hmwTav3Zi4XAQ434UZcRVrJFRkZvv8TpmMhMTVb8+gyZaQ==
=F/gP
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-21jul21' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
dtoc improvements to show better warnings
minor test build fixes
sandbox fixes for SDL2 and running TPL
bloblist resize feature
binman multithreading
The sandbox can handle signals. Due to a damaged global data pointer
additional exceptions in the signal handler may occur leading to an endless
loop. In this case leave the handling of the secondary exception to the
operating system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for reading devicetree flags for MMC devices. With this we
can distinguish between fixed and removable drives. Note that this
information is only available when the device is probed, not when it is
bound, since it is read in the of_to_plat() method. This could be changed
if needed later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
SDL provides a hinting feature which provides a higher-quality image
with the double-display option (-K). Enable it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the display does not show on some machines, e.g. Ubunutu
20.04 but the reason is unknown. Add a work-around until this can be
determined.
Also include more error checking just in case.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SPL header has a function for obtaining the phase in capital letters,
e.g. 'SPL'. Add one for lower-case also, as used by sandbox.
Use this to generalise the sandbox logic for determining the filename of
the next sandbox executable. This can provide support for VPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch reverts the following commits:
- 4b4159d0f3 ("riscv: dts: add dts for unmatched rev1")
- ffe9a394df ("board: sifive: support spl multi-dtb on unmatched board")
We won't plan to support unmatched that the revision below 3 in u-boot,
so they can be dropped because they might be useless.
Changed in v2:
- rebase codebase to the latest master branch
Signed-off-by: Zong Li <zong.li@sifive.com>
Suggested-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
If force_reloc flag is not set and booti is called for an address
ouside RAM (i. e. QSPI NOR flash), we should honor that and not try
to force relocation in a bogus fashion.
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The RPC HF might be locked by ATF, and any access to its register
space would result in complete hang. Disable the RPC HF by default.
The ATF should be patched to set RPC node status = "okay" in the DT
fragment it passes to U-Boot in case the RPC HF access is unlocked,
and that way U-Boot could access the RPC HF safely.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The CPU: print only has one space after it, while the other prints
from U-Boot align the value to offset 7. Align the CPU: print too.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add sysinfo node and phandle to the board ID EEPROM on all boards
where this functionality is described in DT, which is Salvator-X(S),
ULCB and Ebisu. The u-boot,dm-pre-reloc is necessary here, since the
sysinfo must be available early during boot. The V3M and V3H boards
currently do not describe this board ID EEPROM in upstream DT, but
that could be easily added later, once the DTs contain the necessary
nodes.
ULCB and Ebisu needs the full EEPROM node in the u-boot extras DT,
since the EEPROM node is still missing in the upstream DTs. Ebisu
also needs extra compatible string override for the i2c_dvfs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The RGMII ports on LS1043ARDB platforms require both RX and TX internal
delays to be enabled. The device tree reports only the TX ID because the
RX ID used to be enabled by default.
With the addition of RX ID support for the Realtek 8211F PHY driver in
commit e32e4d0f58 ("net: phy: realtek: add rx delay support for
RTL8211F"), the RX ID is disabled by the driver if not reported explicitly.
This causes the RX to no longer work.
Change the phy-connection-type for the RGMII ports to "rgmii-id" in order
to enable both RX and TX internal delays.
Fixes: be1d758969 ("ARM: dts: add QorIQ DPAA 1 FMan v3 to LS1043ARDB")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Marvell SheevaPlug: Convert Ethernet and SATA to Driver Model (Tony)
- Zyxel NSA310S NAS: Convert to Driver Model (Tony)
- Turris_omnia: Add `u-boot-env` NOR partition (Marek)
- Turris_omnia: Fixup MTD partitions in Linux' DTB (Marek)
- Espressobin: Enable 'mtd' command and define SPI NOR partitions (Pali)
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
# Conflicts:
# arch/arm/mach-omap2/am33xx/Kconfig
U-Boot now supports parsing SPI NOR partitions from Device Tree. So enable
'mtd' command support for Espressobin board and define partition layout in
U-Boot Espressobin DTS file. Access to SPI NOR via 'sf' command is old
method and 'mtd' command is now preferred variant.
From include file remove '#define CONFIG_MTD_PARTITIONS' as this option is
now defined and enabled in defconfig file. This change is required to fix
compile error:
CC arch/arm/lib/asm-offsets.s
In file included from include/config.h:4,
from include/common.h:16,
from lib/asm-offsets.c:14:
include/configs/mvebu_armada-37xx.h:63: warning: "CONFIG_MTD_PARTITIONS" redefined
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
In file included from ././include/linux/kconfig.h:4,
from <command-line>:
include/generated/autoconf.h:44: note: this is the location of the previous definition
#define CONFIG_MTD_PARTITIONS 1
After enabling support for mtd command, output from 'mtd list' on
Espressobin board is:
=> mtd list
List of MTD devices:
* w25q32dw
- device: spi-flash@0
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/internal-regs/spi@10600/spi-flash@0
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000400000 : "w25q32dw"
- 0x000000000000-0x0000003f0000 : "firmware"
- 0x0000003f0000-0x000000400000 : "u-boot-env"
=>
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Specify a separate partition `u-boot-env` for U-Boot's env settings for
the Turris Omnia board.
Do this only in U-Boot's specific DTS. We do not want to do this in
Linux' official DTS, because Omnia's stock U-Boot stores env at a
different address, and there are still boards with stock U-Boot.
In a subsequent patch will add board code that fixes Linux's DTB before
booting Linux.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add device tree kirkwood-nsa310s.dts for Zyxel NSA310S board to
convert to Driver Model.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
As the deadline for migration to DM_USB, when using a USB host
controller has now gone two years past the deadline, enforce migration.
This is done by:
- Ensuring that all host controller options (other than the very legacy
old MUSB ones) now select USB_HOST. USB_HOST now enforces DM_USB and
OF_CONTROL.
- Remove other parts of Kconfig logic that had platforms pick DM_USB.
- To keep Kconfig happy, have some select statements test for USB_HOST
as well.
- Re-order some Kconfig entries and menus so that we can cleanly pick
host or gadget roles. For the various HCD options that have platform
glue options, group them together and update dependencies in some
cases.
- As SPL_DM_USB is not required, on platforms that had not yet enabled
it, disable it.
Cc: Marek Vasut <marex@denx.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Samuel Holland <samuel@sholland.org>
Cc: FUKAUMI Naoki <naobsd@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add DT binding for GT64120 and MSC01 PCI controllers. Only
GT64120 is enabled by default to support Qemu. The MSC01 node
will be dynamically enabled by Malta board code dependent
on the plugged core card.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add clock function to setup relevant clocks for USB3.0 controllers and
PHYs on i.MX8MQ
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
Remove the mmc alias no more required as the sequence number
of mmc device is used for boot_instance.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use the device sequence number in boot_instance variable
and no more the SDMMC instance provided by ROM code/TF-A.
After this patch we don't need to define the mmc alias in
device tree, for example:
mmc0 = &sdmmc1;
mmc1 = &sdmmc2;
mmc2 = &sdmmc3;
to have a correct mapping between the ROM code boot device =
"${boot_device}${boot_instance}" and the MMC device in U-Boot.
With this patch the 'mmc0' device (used in mmc commands) is
always used when only one instance sdmmc is activated in device
tree, even if it is only the sdmmc2 or sdmmc3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use the existing defines PMIC_SIZE and OTP_SIZE and a new define
CMD_SIZE for virtual partition size.
This patch corrects the size for OTP partition in alternate name
(1024 instead of 512) and avoids other alignment issues.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable the clocks during syscon probe when they are present in device tree.
This patch avoids a freeze when the SYSCFG clock is not enabled by
TF-A / OP-TEE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The expected sequence to close the device
1/ Load key in DDR with any supported load command
2/ Update OTP with key: STM32MP> stm32key read <addr>
At this point the device is able to perform image authentication but
non-authenticated images can still be used and executed.
So it is the last moment to test boot with signed binary and
check that the ROM code accepts them.
3/ Close the device: only signed binary will be accepted !!
STM32MP> stm32key close
Warning: Programming these OTP is an irreversible operation!
This may brick your system if the HASH of key is invalid
This command should be deactivated by default in real product.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Allow to read the OTP value and lock status with the command
$> stm32key read.
This patch also protects the stm32key fuse command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a helper function to access to BSEC misc driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Lock the OTP value of key's hash after the command
$> stm32key fuse <address>
This operation forbids a second update of these OTP as they are
ECC protected in BSEC: any update of these OTP with a different value
causes a BSEC disturb error and the closed chip will be bricked.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Simplify parsing the command argument by using
the macro U_BOOT_CMD_WITH_SUBCMDS.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This command is used to evaluate the secure boot on stm32mp SOC,
it is deactivated by default in real products.
We activate this command only in STMicroelectronics defconfig
used with the evaluation boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reduce the content of short help message for stm32prog command and
removed the carriage return to fix the display of 'help' command when
this command is activated.
Fixes: 954bd1a923 ("stm32mp: add the command stm32prog")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In this case the value seems save to pass to os_free(). Add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 165109)
Add voltage and thermal management (VTM) node. The efuse values for the
OPPs are stored under the VTM, and is needed for AVS class 0 support.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210714205300.17424-4-g-tammana@ti.com
secureworld_exit() is only used in one file, so make it static
to that file and remove it from sys_proto.h. This
may help with some further optimization in the future.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210625192308.277136-3-aford173@gmail.com
try_unlock_memory() is only used in one file, so make it static
in that file,remove it from the sys_proto header file, and relocate
it into the #ifdef section that call it. This will make it only built
under the conditions when it is called, and it may help with some
further optimization in the future.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210625192308.277136-2-aford173@gmail.com
The `struct udevice *` reference is needed for either of the
K3_LOAD_SYSFW, K3_AM64_DDRSS config guards. Adding the missing
K3_AM64_DDRSS guard.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210624171614.14244-1-g-tammana@ti.com
Add the DT nodes for the ICSSG0, ICSSG1 and ICSSG2 processor subsystems
that are present on the K3 AM65x SoCs. The three ICSSGs are identical
to each other for the most part, with the ICSSG2 supporting slightly
enhanced features for supporting SGMII PRU Ethernet. Each ICSSG instance
is represented by a PRUSS subsystem node. These nodes are enabled by
default.
DT nodes are fetch from Linux 5.13 Kernel.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210622063431.3151-5-lokeshvutla@ti.com
So far all the u-boot specific properties for both r5 and a53 are
placed in k3-am654-base-board-u-boot.dtsi. But there are few a53
nodes that should be updated but doesn't belong to r5. So create a
separate r5 specific u-boot dtsi.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210622063431.3151-4-lokeshvutla@ti.com
The final 128KB in SRAM is reserved by default for DMSC-lite code and
secure proxy communication buffer. The memory region used for DMSC-lite
code can be optionally freed up by secure firmware API[1]. However, the
buffer for secure proxy communication is not configurable. This default
hardware configuration is unique for AM64.
Therefore, indicate the area reserved for DMSC-lite code and secure proxy
communication buffer in the oc_sram device tree node.
[1] - http://downloads.ti.com/tisci/esd/latest/6_topic_user_guides/security_handover.html#triggering-security-handover
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210616163821.20457-3-a-govindraju@ti.com
Earlier, the region 0x701c0000 to 0x701dffff was firewalled off because of
a bug in SYSFW. In the v2021.05 release of SYSFW this bug has been fixed
and this region can now be used for other allocations.
Therefore, move TF-A's load address to 0x701c0000 and update its location
in the device tree node. Also, increase the size allocated for TF-A to
account for future expansions.
Fixes: defd62ca13 ("arm: dts: k3-am64-main: Update the location of ATF in SRAM and increase its max size")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210616163821.20457-2-a-govindraju@ti.com
pinmux update for guardian board
- control ASP Board Power: GPIO, on/off ASP Board Power
- control Coincell Voltage Measurement: GPIO, enable/disable
ADC measurements
- powerOff Device GPIO-PowerOff, cut the PMIC supply
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210611161350.2141-7-Gireesh.Hiremath@in.bosch.com
This is a revert of a recent logic change in setup_zimage(). We do
actually need to install this information always. Change it to install
from the Coreboot tables if available, else the normal source.
Fixes: e7bae8283f ("x86: Allow installing an e820 when booting from coreboot")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
All the x86 devicetree files are built at once, whichever board is
actually being built. If coreboot is the target build, CONFIG_ROM_SIZE
is not defined and samus cannot build Chromium OS verified boot. Add
this condition to avoid errors about CONFIG_ROM_SIZE being missing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use VENDOR_COREBOOT instead of TARGET_COREBOOT so we can have multiple
coreboot boards, sharing options. Only SYS_CONFIG_NAME needs to be
defined TARGET_COREBOOT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function comment for get_coreboot_info() and a declaration for
cb_get_sysinfo(), since this may be called from elsewhere.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A recent change to disable cache setup when booting from coreboot
assumed that this has been done by SPL. The result is that for the
coreboot board, the cache is disabled (in start.S) and never
re-enabled.
If the cache was turned off, as it is on boards without SPL, we should
turn it back on. Add this new condition.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These constants conflict with error codes returned by the MP
implementation when something is wrong. In particular, mp_first_cpu()
returns MP_SELECT_BSP when running without multiprocessing enabled.
Since this is -2, it is interpreted as an error by callers, which
expect a positive CPU number for the first CPU.
Correct this by using a different range for the pre-defined CPU
numbers, above zero and out of the range of possible CPU values. For
now it is safe to assume there are no more than 64K CPUs.
This fixes the 'mtrr' command when CONFIG_SMP is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When starting U-Boot from a previous-stage bootloader we presumably don't
need to set up the variable MTRRs. In fact this could be harmful if the
existing settings are not what U-Boot uses.
Skip that step in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If fixup offset is zero then there is nothing to fix. All calculation in
this case just increase addresses by value zero which results in identity.
So in this case skip whole fixup re-calculation as it is not needed.
This is just an optimization for special case when fix_offset is zero which
skips code path which does only identity operations (meaning nothing). No
functional changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The U-Boot "stemmy" board is mainly intended to simplify booting
mainline Linux on various smartphones from Samsung based on ST-Ericsson
Ux500. While the mainline kernel is working great, there are still some
features missing there. In particular, it is currently not possible to
charge the battery when using the mainline kernel.
This means that it is still necessary to boot the downstream/vendor
kernel from Samsung sometimes to charge the device. That kernel is
ancient, still uses board files + ATAGS instead of device trees and
relies on a strange very long kernel command line hardcoded in the
Samsung bootloader.
Actually, since mainline is booted with device trees there is a very
simple way to make the old downstream kernel work as well: We can
simply take most of the ATAGS passed to U-Boot from the Samsung
bootloader and copy them as-is when booting a kernel without device
tree. That way the long command line and other needed ATAGS are copied
as-is without having to bother with them.
The only exception is the ATAG_INITRD - since the initrd is loaded
by U-Boot, the atag for that should be generated in U-Boot so it points
to the correct address. All other ATAGS are copied as-is and not
generated in U-Boot.
Also use the chance and provide a serial# for U-Boot by parsing the
ATAG_SERIAL that is also passed by the Samsung bootloader.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
At the moment the "stemmy" board attempts to detect the RAM size with
a simple memory test (get_ram_size()). Unfortunately, this does not work
correctly for devices with 768 MiB RAM (e.g. Samsung Galaxy Ace 2
(GT-I8160), "codina"). Reading/writing memory after the 768 MiB RAM
succeeds but actually overwrites some earlier parts of the memory.
For U-Boot this does not result in any major problems, but on Linux
this will eventually lead to strange crashes because of the memory
corruption.
Since the "stemmy" U-Boot port is designed to be chainloaded from
the original Samsung bootloader, the most reliable way to get the
available amount of RAM is to look at the ATAGS passed by the Samsung
bootloader. Fortunately, the header used to generate ATAGS in U-Boot
(asm/setup.h) can also be easily used to parse them.
Also clarify and simplify stemmy.h a bit to make it more clear where
some of the magic values in there are actually coming from.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add the device tree for Akebi96. Akebi96 is a 96boards certified
development board based on UniPhier LD20.
( https://www.96boards.org/product/akebi96/ )
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
According to arch/arm/lib/crt0_64.S, the BSS section is "UNAVAILABLE"
and uninitialized before relocation. Also, it overlaps with the
appended DTB before relocation, so writing data into a variable
in the BSS section might corrupt the appended DTB.
Unfortunately, pinctrl-apq8016.c and pinctrl-apq8096.c do place the
"pin_name" variable in the BSS section (since it's uninitialized).
It's also used before relocation, when setting up the pinctrl for
the serial driver.
On DB410c this causes "GPIO_5" to be written into some part of an
appended DTB, e.g.:
80111820: edfe0dd0 9f100000 38000000 c00e0000 ...........8....
80111830: 28000000 11000000 10000000 00000000 ...(............
80111840: 4f495047 8800355f 00000000 00000000 GPIO_5..........
80111850: 00000000 00000000 01000000 00000000 ................
80111860: 03000000 04000000 00000000 02000000 ................
80111870: 03000000 04000000 0f000000 02000000 ................
80111880: 03000000 2d000000 1b000000 6c617551 .......-....Qual
80111890: 6d6d6f63 63655420 6c6f6e68 6569676f comm Technologie
Depending on the part of the DTB that is corrupted this might not
cause any problems, but it can also result in strange reboots
without any serial output.
Fortunately, in practice this does not cause issues on DB410c yet
because board_fdt_blob_setup() in dragonboard410c.c currently
overrides the appended DTB with the one passed by the previous
bootloader (LK) (which does not get corrupted).
DB820c does not have board_fdt_blob_setup() so I would expect it to
be affected by this problem. Perhaps everyone was just fortunate to
not compile an U-Boot configuration where the pin_name corrupts an
important part of the DTB.
Make sure "pin_name" is explicitly placed in the .data section
instead of .bss to fix this.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In case the iMX8M boot from eMMC boot partition and the primary image
is corrupted, the BootROM is capable of starting a secondary image in
the other eMMC boot partition as a fallback.
However, the BootROM leaves the eMMC BOOT_PARTITION_ENABLE setting as
it was, i.e. pointing to the boot partition containing the corrupted
image, and the BootROM does not provide any indication that this sort
of fallback occured.
According to AN12853 i.MX ROMs Log Events, Rev. 0, May 2020, it is
possible to determine whether fallback event occurred by parsing the
ROM event log. In case ROM event ID 0x51 is present, fallback event
did occur.
This patch implements ROM event log parsing and search for event ID
0x51 for all iMX8M SoCs, and based on that corrects the eMMC boot
partition selection. This way, the SPL loads the remaining boot
components from the same eMMC boot partition from which it was
started, even in case of the fallback.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Harald Seiler <hws@denx.de>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Fix the dsa switch config:
- remove the unnecessary phy-mode from the switch itself
- added the necessary fixed-link node to the non-cpu ports required
for U-Boot DSA
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
- i.MX8M Mini SoC
- LPDDR4 DRAM
- eMMC FLASH
- SPI FRAM
- Gateworks System Controller (GSC)
- Atmel ATECC Crypto Authentication
- USB 2.0
- Microchip GbE Switch
- Multiple multi-protocol RS232/RS485/RS422 Serial ports
- onboard 802.11ac WiFi / BT
- microSD socket
- miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
- Wide range DC power input
- 802.3at PoE
To add support for this board:
- add dts from Linux (accepted for v5.14)
- add SPL PMIC config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Make macros actually use passed parameter instead of local variables
that happen
to be named the same as symbols in macro expansion.
Signed-off-by: Kacper Kubkowski <kkubkowski@fluence.pl>
With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This update includes eqos support and some minor changes.
Synced with kernel commit
412627f6ffe3 ("arm64: dts: imx8mp-phyboard-pollux-rdk: Add missing pinctrl entry")
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Factor out the common node settings for dm-spl and dm-pre-reloc
and move them to imx8mp-u-boot.dtsi
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If reset-gpio is defined by device-tree use that if
CONFIG_PCIE_IMX_PERST_GPIO is not defined.
Note that after this the following boards which define
CONFIG_PCIE_IMX_PERST_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
- mx6sabresd
- mx6sxsabresd
- novena
- tbs2910
- vining_2000
Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_PERST_GPIO and does
not have reset-gpios defined it it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_PERST_GPIO globally can't be done until that board adds
reset-gpios.
Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD)
Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD)
Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD)
Cc: Soeren Moch <smoch@web.de> (maintainer:TBS2910 BOARD)
Cc: Silvio Fricke <open-source@softing.de> (maintainer:VINING_2000 BOARD)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Some IPs have their accessible address space restricted by the
interconnect. Let's make sure U-Boot only ever uses the space below
the 4G address boundary (which is 3GiB big), even when the effective
available memory is bigger.
We implement board_get_usable_ram_top() for all i.MX8M SoCs, as the
whole family is affected by this.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Aside from the usual fixes and updates one visible change is the
MMC update, which fixes some lingering bugs and gives a decent speed
increase on some boards (9->19 MB/s on H6, 21->43 MB/s on A64 eMMC).
I am keeping an watchful eye on bug reports here, to spot any correctness
regressions.
Another change is finally the enablement of the first USB host port on
many boards without micro-USB (data) sockets, like the Pine64 family.
That doubles the number of usable USB ports from 1 to 2 on those boards.
Some smaller fixes, 4GB DRAM support (on the H616) and a new board (ZeroPi)
conclude this first round of changes.
Compile-tested for all 157 sunxi boards, boot-tested on Pine H64,
Pine64-LTS, OrangePi Zero 2 and BananaPi M2 Berry.
Summary:
- DT update for H3/H5/H6
- Enable first USB port on boards without micro-USB
- ZeroPi board support
- 4GB DRAM support for H616 boards
- MMC fixes and speed improvement
- some fixes
To avoid the complexity of DMA operations (with chained descriptors), we
use repeated MMIO reads and writes to the SD_FIFO_REG, which allows us
to drain or fill the MMC data buffer FIFO very easily.
However those MMIO accesses are somewhat costly, so this limits our MMC
performance, to between 17 and 22 MB/s, but down to 9.5 MB/s on the H6
(partly due to the lower AHB1 frequency).
As it turns out we read the FIFO status register after *every* word we
read or write, which effectively doubles the number of MMIO accesses,
thus effectively more than halving our performance.
To avoid this overhead, we can make use of the FIFO level bits, which are
in the very same FIFO status registers.
So for a read request, we now can collect as many words as the FIFO
level originally indicated, and only then need to update the status
register.
We don't know for sure the size of the FIFO (and it seems to differ
across SoCs anyway), so writing is more fragile, which is why we still
use the old method for that. If we find a minimum FIFO size available on
all SoCs, we could use that, in a later optimisation.
This patch increases the eMMC read speed on a Pine64-LTS from about
22MB/s to 44 MB/s. SD card reads don't gain that much, but with 23 MB/s
we now reach the practical limit for 3.3V SD cards.
On the H6 we double our transfer speed, from 9.5 MB/s to 19.7 MB/s.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
All SoCs since the Allwinner A64 (H5, H6, R40, H616) feature the so
called "new timing mode", so enable this in Kconfig for those SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Most Allwinner SoCs which use the so called "new timing mode" in their
MMC controllers actually use the double-rate PLL6/PERIPH0 clock as their
parent input clock. This is interestingly enough compensated by a hidden
"by 2" post-divider in the mod clock, so the divider and actual output
rate stay the same.
Even though for the H6 and H616 (but only for them!) we use the doubled
input clock for the divider computation, we never accounted for the
implicit post-divider, so the clock was only half the speed on those SoCs.
This didn't really matter so far, as our slow MMIO routine limits the
transfer speed anyway, but we will fix this soon.
Clean up the code around that selection, to always use the normal PLL6
(PERIPH0(1x)) clock as an input. As the rate and divider are the same,
that makes no difference.
Explain the hardware differences in a comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The H616 is our first supported Allwinner SoC which goes beyond the 4GB
address space "barrier", by having more than 32 address bits.
Lift the preliminary 3GB DRAM limit for the H616, and update the page
table setup on the way, to actually map that last GB as well.
As not all devices are actually capable of dealing with more than 32
bits (the DMA in the EMAC for instance), we also limit U-Boot's own
DRAM usage to 4GB on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
ZeroPi is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner H3 SOC.
ZeroPi features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 256MB/512MB DDR3 RAM
- microsd slot
- 10/100/1000Mbps Ethernet
- Debug Serial Port
- DC 5V/2A power-supply
Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Most clock factors and dividers in the H6 PLLs use a "+1 encoding",
which we were missing on two occasions.
This fixes the MMC clock setup on the H6, which could be slightly off due
to the wrong parent frequency:
mmc 2 set mod-clk req 52000000 parent 1176000000 n 2 m 12 rate 49000000
Also the CPU frequency (PLL1) was a tad too high before.
For PLL5 (DRAM) we already accounted for this +1, but in the DRAM code
itself, not in the bit field macro. Move this there to be aligned with
what the other SoCs and other PLLs do.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Update the H3 DT files from the Linux 5.12 release.
The changes update some boards, and don't affect U-Boot, but fix Gigabit
Ethernet when this DT is passed on to the Linux kernel.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Update the H5 DT files from the Linux 5.12 release.
The changes don't affect U-Boot at all, but fix Gigabit Ethernet when
this DT is passed on to the Linux kernel. It also introduces DVFS.
This also updates the shared sunxi-h3-h5.dtsi, but that only adds nodes
that are of no concern to U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Update the H6 DT files from the Linux 5.12 release.
The changes are minimal (many LED node renames), but also help to enable
USB port 0 in U-Boot (later), enable the RSB device (not yet used in
U-Boot), and also introduce an MMC frequency limit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As seen with clang-12:
warning: __asm_invalidate_l3_dcache changed binding to STB_WEAK
As we indeed use ENTRY and then declare the function weak manually. Use
the WEAK declarative from <linux/linkage.h> instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
On arm64, board info is not applicable and kernel command line patched into
the DT, so the LMB reservation here makes no sense anymore. On legacy arm32,
this might still be necessary on systems which do not use DT or use legacy
ATAGS. Disable this LMB reservation on arm64.
This also permits Linux DT to specify reserved memory node at address close
to the end of DRAM bank, i.e. overlaping with U-Boot location. Since after
boot, U-Boot will be no more, this is OK.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Rini <trini@konsulko.com>
Fix following compilation issue when SYS_DCACHE_OFF is enable:
drivers/misc/scmi_agent.c:128: undefined reference to `mmu_set_region_dcache_behaviour'
when SYS_DCACHE_OFF is enable, mmu_set_region_dcache_behaviour() must be
defined.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On implementations that support VHE, the layout of the CPTR_EL2
register depends on whether HCR_EL2.E2H is set. If the bit is
set, CPTR_EL2 uses the same layout as CPACR_EL1 and can in fact
be accessed through that register. In that case, jump to the
EL1 code to enable access to the FP/SIMD registers. This allows
U-Boot to run on systems that pass control to U-Boot in EL2 with
EL2 Host mode enabled such as machines using Apple's M1 SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Acked-by: Marc Zyngier <maz@kernel.org>
While this platform has not yet been converted, there is active efforts
to do so. Keep the platform for now.
This reverts commit aa697e6904.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
also the last SPEAR3XX platform, remove that symbol as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Gerald Kerma <dreagle@doukki.net>
Cc: Tony Dinh <mibodhi@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Ajay Bhargav <contact@8051projects.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it.
This is also the last PL010_SERIAL using board, so remove those
references.
Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_T4160 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8315 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8568 platform, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the only ARCH_T1023 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and are
also missing conversion to CONFIG_DM. Remove them.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI, CONFIG_DM_USB or
in some cases CONFIG_DM itself by the deadline. Remove them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is all of the CONFIG_M548x platforms as well,
remove that code.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With x86 we can execute an option ROM either natively or using the
x86 emulator (if enabled with CONFIG_BIOSEMU). Both of these share
the _X86EMU_env variable, with the native code using it to hold
register state during interrupt processing.
At present, in 32-bit U-Boot, the variable is declared twice, once
in common code and once in code only compiled with CONFIG_BIOSEMU.
With GCC 11 this causes a 'multiple definitions' error on boards
with CONFIG_BIOSEMU.
Drop the emulator definition when CONFIG_BIOSEMU is used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
When we do not have bootstage enabled, rather than include an empty
dummy function, we just don't reference it. This saves us space in some
tight builds. This also shows a few cases where show_boot_progress was
incorrectly guarded before.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDkSkAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyD24B/9t87hFqWovJvVAcoUT
JoTqFblplE4Sckssy0cQyR7sRpzuZEaakUeAxaLFecBN6Tn30YJEG3hNpEDCLEbA
hn/oiZ4hQ3JA9Yu2SHepQi0fLqdAjkQtMXy57o3Mk20GBLtPtpdItUHxg3iyeMSj
Ny1mm/KjL6ltmNeGfYfeqRf435Rm718DB94wCZTgS9woYe3Z5YRDNBPyL7u27hpY
2WiyvvU9EA12mjGYdEt5sCqnTQZFtHHlEWNHz4a3db6HkcPV7pfr+SpTNJjcFhIg
O7VN7yUTwnV0UGu5IXTWcZqFIqJkLPbPX5cvkSBnnaGge4e0K3Cw36Nv/EqCY8LX
gWfu
=Ru8k
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2021.10 cycle:
This small fixes set is dedicated to fixing the onewire subsystem for
the at91 boards which was broken since 2020.04.
Previous device tree for OpenPiton emits a warning during compilation.
This commit fixes the previous warning adds dts to the OpenPiton RISC-V
board and added the device tree to MAINTAINER file.
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
It looks like SD card detection is broken at the moment for DB410c.
The eMMC is detected correctly, but the SD card is not.
This is probably similar to the issue fixed in commit 8505147403
("mmc: msm_sdhci: Use mmc_of_parse for setting host_caps") for eMMC,
except that the SD card does not have a property like "non-removable"
that skips the card detection.
The SDHCI on DB410c cannot detect itself if a SD card is inserted,
so add the necessary cd-gpios to make SD card detection work again.
While at it, fix the #gpio-cells for the soc_gpios to avoid DTC
warnings - the soc_gpios are actually already used with two cells
for the gpio-leds so this was just wrong all the time.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The GICC register used by u-boot is 0x0a20c000, which is actually a GICC
for WCNSS, the WLAN processor. U-boot runs on the Application Processor,
therefore it should use APCS GICC instead. Hence, correct it with APCS GICC
register address.
Signed-off-by: Sheep Sun <sunxiaoyang2003@gmail.com>
Add basic support for running U-Boot on the Embedded Artists LPC3250
Developer's Kit v2 board by launching U-Boot from the board's s1l loader
(which comes pre-installed on the board).
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Import the dtsi, dts, and clock binding files for the lpc32xx ea3250 board
directly and unmodified from the latest Linux kernel.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
There's nothing special or unique to the lpc32xx that requires its own config
parameter for specifying the console uart index. Therefore instead of using
the lpc32xx-specific CONFIG_SYS_LPC32XX_UART include parameter, use the
already-available CONFIG_CONS_INDEX from Kconfig.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.
For more information, see this page;
https://www.96boards.org/product/developerbox/
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add device trees for 96boards EE DeveloperBox and basement SynQuacer
SoC dtsi. These files are imported from EDK2
commit 83d38b0b4c0f240d4488c600bbe87cea391f3922
as-is (except for the changes #include path and some macros).
And add U-Boot specific changes in synquacer-sc2a11-developerbox-u-boot.dtsi
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Since some SoCs and boards do not hae extra asm/arch/gpio.h,
introduce CONFIG_GPIO_EXTRA_HEADER instead of adding
!define(CONFIG_ARCH_XXXX) in asm/gpio.h.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add support for 1.3GHz, 1.35GHz and 1.4GHz parts. This is based on
equivalent code in Broadcom's LDK 5.0.6.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This patch adds a limited pulse-width modulator to sandbox's Chromium OS
Embedded Controller emulation. The emulated PWM device supports multiple
channels but can only set a duty cycle for each, as the actual EC
doesn't expose any functionality or information other than that. Though
the EC supports specifying the PWM channel by its type (e.g. display
backlight, keyboard backlight), this is not implemented in the emulation
as nothing in U-Boot uses this type specification.
This emulated PWM device is then used to test the Chromium OS PWM driver
in sandbox. Adding the required device node to the sandbox test
device-tree unfortunately makes it the first PWM device, so this also
touches some other tests to make sure they still use the sandbox PWM.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
state_uninit() and dm_uninit() are mutually exclusive:
state_uninit() prints via drivers. So it cannot be executed after
dm_uninit().
dm_uninit() requires memory. So it cannot be executed after state_uninit()
which releases all memory.
Just skip dm_uninit() when resetting the sandbox. We will wake up in a new
process and allocate new memory. So this cleanup is not required. We don't
do it in sandbox_exit() either.
This avoids a segmentation error when efi_reset_system_boottime() is
invoked by a UEFI application.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Addresses in state->ram_buf must be in the low 4 GiB of the address space.
Otherwise we cannot correctly fill SMBIOS tables. This shows up in warnings
like:
WARNING: SMBIOS table_address overflow 7f752735e020
Ensure that state->ram_buf is initialized by the first invocation of
os_malloc().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present if sandbox crashes it prints a message and tries to exit. But
with the recently introduced signal handler, it often seems to get stuck
in a loop until the stack overflows:
Segmentation violation
Segmentation violation
Segmentation violation
Segmentation violation
Segmentation violation
Segmentation violation
Segmentation violation
...
The signal handler is only useful for a few tests, as I understand it.
Make it optional.
Signed-off-by: Simon Glass <sjg@chromium.org>
The difference between unmatched rev3 and rev1 is DDR timing, the rev3
uses 1866 MT/s for 16GiB, and rev1 uses 2133 MT/s for 8GiB.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
There are different DDR parameter settings for different board
revisions. Add a new interface to get the PCB revision to determine
which DT should be selected at runtime.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enable SPL_I2C_SUPPORT for fu740, and add 'u-boot,dm-spl' property in
i2c node.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The GPIO polarity for onewire must be GPIO_ACTIVE_HIGH.
On previous versions this used to work as it looks like the right flag values
are being passed since :
https://lists.denx.de/pipermail/u-boot/2020-April/407195.html
And that series broke the old functionality for onewire nodes.
Some boards had the correct value for the polarity, but it wasn't clear
so I replaced it with the right macro for the flag, instead of an empty value.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This patch adds openpiton-riscv64 SOC support. In particular, this
board supports a standard bootflow through zsbl->u-boot SPL->
opensbi->u-boot proper->Linux. There are separate defconfigs for
building u-boot SPL and u-boot proper
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Now that u-boot gained DSA support, and it is already enabled for the
kontron_sl28 board, add the last missing piece and enable the
corresponding devices it in the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
The enetc-2 port is used as DSA master (connected back-to-back to
mscc_felix_port4). Since the convention is to not enable ports in the
common SoC dtsi unless they are used on the board, then enable enetc-2
only when mscc_felix_port4 itself is enabled.
All existing device trees appear to adhere to this rule, so disable
enetc-2 in the SoC dtsi.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
To comply with the device tree bindings expectations for an Ethernet
controller, as well as to simplify the driver code, declare fixed-link
nodes for the internal ENETC ports (attached to the mscc_felix switch).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are no PCB trace delays on this board, so the PHY needs to enable
its internal ones in order to have a proper electrical connection to the
enetc MAC.
Fixes: b32e9a7578 ("arm: dts: ls1028a updates for network interfaces")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Due to an upstream change, the ls1028a.dtsi bindings for the mscc_felix
switch got accepted with all ports disabled by default and with no link
to the DSA master - this needs to be done on a per board basis.
Note that enetc-2 is not currently disabled in the ls1028a.dtsi, but
presumably at some point it might become. Explicitly enable it in the
QDS device trees anyway, to proactively avoid issues when that happens.
Fixes: a7fdac7e2a ("arm: dts: ls1028a: define QDS networking protocol combinations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYN105QAKCRDKSWXLKUoM
IZiFAJ9CIiEpHiBbnAhA0VOMGoaXHGULywCdED/5dNgVtc1C7y4avzETbEyWzD4=
=CdMa
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.10
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
If both POSITION_INDEPENDENT and SYS_RELOC_GD_ENV_ADDR are enabled,
wherever original env is placed anywhere, it should be relocated to
the right address.
Relocation offset gd->reloc_off is calculated with SYS_TEXT_BASE in
setup_reloc() and env address gd->env_addr is relocated by the offset in
initr_reloc_global_data().
gd->env_addr
= (orig env) + gd->reloc_off
= (orig env) + (gd->relocaddr - SYS_TEXT_BASE)
However, SYS_TEXT_BASE isn't always runtime base address when
POSITION_INDEPENDENT is enabled. So the relocated env_addr might point to
wrong address. For example, if SYS_TEXT_BASE is zero, gd->env_addr is
out of memory location and memory exception will occur.
There is a difference between linked address such as SYS_TEXT_BASE and
runtime base address. In _main, the difference is calculated as
"run-vs-link" offset. The env_addr should also be added to the offset
to fix the address.
gd->env_addr
= (orig env) + ("run-vs-link" offset) + gd->reloc_off
= (orig env) + (SYS_TEXT_BASE - _start) + (gd->relocaddr - SYS_TEXT_BASE)
= (orig env) + (gd->relocaddr - _start)
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This patch adds psgtr clocks and phy entry for USB0, USB1 and SATA node for
zc1751-xm017-dc3 board.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The board detection is incorrectly stating it's an rcar3 variant
instead of an RZ/G2 variant on all the r8a774*1_beacon boards.
Set the flag to correctly display as RZ/G2[M/N/H]
Signed-off-by: Adam Ford <aford173@gmail.com>
Enable basic PSCI support for R8A779A0 V3U Falcon
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add board code for the R8A779A0 V3U Falcon board.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - various small rebase fixes and clean ups
Add platform code to support R8A779A0 V3U SoC.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The R-Car V3U does support RPC interface, however the support for it is
missing in upstream Linux DTs as of commit 9f4ad9e425a1 ("Linux 5.12"),
add the node into u-boot.dtsi to let U-Boot access the SPI NOR or HF.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add R8A779A0 V3U DT extras for U-Boot.
Based on "ARM: dts: renesas: Add R8A779A0 V3U DTs"
by Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
- x86: Discard .note.gnu.property sections
- nvme: Skip block device creation for inactive namespaces
- nvme: Convert NVMe doc to reST, and various minor fixes
All symbols that are defined in Kconfig will always be defined (or not)
prior to preprocessing due to the -include directive while building.
However, symbols which are not yet migrated will only be defined (or
not) once the board config.h is included, via <config.h>. While the end
goal must be to migrate all symbols, today we have cases where the size
of gd will get mismatched within the build, based on include order.
Mitigate this by making sure that any <asm/global_data.h> that uses
symbols not in Kconfig does start with <config.h>. Remove this when not
needed.
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the changes in commit 588efcdd72fc ("powerpc: Don't use relative
include for config.h in global_data.h") fixing the root of the problem,
we no longer need this re-inclusion.
This reverts commit f6c0d365d3.
Cc: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As there is an arch/powerpc/include/asm/config.h file using "" to get
config.h here can lead to using that rather than include/config.h. This
in turn can lead to a mismatch in the size of gd.
Cc: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
When switching to kernel.org x86_64 gcc 11.1.0 toolchain, u-boot.rom
built from qemu-x86_defconfig no longer boots anymore. Investigation
shows that U-Boot fails at a very early stage during the boot process,
in fdtdec_prepare_fdt() where fdt_check_header() complains that there
is not a valid device tree found at gd->fdt_blob which points to _end.
Now _end points to an allocated section .note.gnu.property which of
course is wrong.
This issue is however not seen when using the default Ubuntu 20.04 gnu
toolchain (gcc 9.3.0 with binutils 2.34). Further investigation shows
that it is caused by a behavior change of binutils v2.36 which is part
of the kernel.org gcc 11.1.0 toolchain, via the following commit:
939b95c77bf2 ("Linux/x86: Configure gas with --enable-x86-used-note by default")
In fact, there was already a regression bug report [1] for binutils two
months ago, but the binutils folks did not think it is a bug :(
To resolve this, there are several options:
* pass -Wa,-mx86-used-note=no to gas
* pass -R .note.gnu.property to objcopy
* discard the section in the linker script
Linux kernel uses the discard way [2], so let's do the same for U-Boot.
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=27753
[2] commit 4caffe6a28d3 ("x86/vdso: Discard .note.gnu.property sections in vDSO")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DT files have been added this year but forgot to update it that's why do it
in separate patch now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is not recommended to have aliases for gpio. In past it was used in
Linux for assigning numbers via sysfs which is deprecated and libgpiod
should be used instead.
In U-Boot this number is used for seq number but gpio offset are not
counted from this number. That's why having these aliases only for seq
number is not needed. As is done in Linux it is the best to use full gpio
name instead of sequence number which depends on sequence in binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Align USB nodes with the latest dt-bindings. It is adding resets, new
interrupt and also some quirks.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc supports new sugar syntax which is easier compare to previous one
that's why also covert overlays for SOM to it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
kv260-revB is different compare to revA (usbhub is wired via i2c) that's
why remove revA compatible string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx ZynqMP supports also addresses above 4GB (32bit) that's why also
generate u-boot.its with 64bit load/entry addresses to also support
different configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Clock setting is not static anymore that's why it depends on firmware setup
that's why remove this comment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Networking subsystem is not using aliases that's why remove them for CAN
devices. There is also no any other Xilinx ZynqMP DT file with them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As per the design specification
"The 16-bit Seconds Calibration Value represents the number of
Oscillator Ticks that are required to measure the largest time
period that is less than or equal to 1 second.
For an oscillator that is 32.768 KHz, this value will be 0x7FFF."
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Historically dpdma and dpsub are placed at the end of files. Move nodes
there for easier comparison among dts files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dwc3 can be used only for higher speeds than super-speed that's why
explicitly set it up.
This is also aligned with other ZynqMP dts files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Uarts already have u-boot,dm-pre-reloc via zynqmp.dtsi that's why there is
no need to have them in platform DT files too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is need to pass entry about secure OS when bl32_entry is defined.
Currently only 64bit support is added but /fit-images node have been
extended to also record if this is 32bit or 64bit secure OS. When this is
tested the code will be update to support this configuration too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The first change is to trying to find out TF-A load address based on
reading elf file. Expectation is that bl31.bin is in the same folder as
bl31.elf. It brings new flexibility to place TF-A to any address (DDR
included).
And also enable TEE generation also with TEE configuration.
Expecation is the same as above that tee.bin and tee.elf are in the same
folder.
User has to just define link to BL31/BL32 binary files and the rest should
be handled by the script.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SMMU is disabled in device tree so this change has no impact.
The benefit is that this way it is in sync with xen.dtsi. Xen enables
the SMMU and makes use of it.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
There is no reason to have CCI no enabled by default. Enable it when your
system configuration requires it. In Xilinx configuration flow this is
work for Device Tree Generator which reads information from HW Design
configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Rename amba to AXI. Based on Xilinx Zynq TRM (Chapter 5) chip is "AXI
point-to-point channels for communicating addresses, data, and response
transactions between master and slave clients. This ARM AMBA 3.0..."
Issues are reported as:
.. amba: $nodename:0: 'amba' does not match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
>From schema:
../github.com/devicetree-org/dt-schema/dtschema/schemas/simple-bus.yaml
Similar change has been done for Xilinx ZynqMP SoC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/8a4bc80debfbb79c296e76fc1e4c173e62657286.1606397101.git.michal.simek@xilinx.com
From U-Boot, loading application on RPU core 0 is fine but loading on
core 1 is not handled properly. Lock-step mode needs both the R5 cores
to be initialized and it is working fine. Whereas in SPLIT mode individual
R5 cores needs to be initialized as they need to execute differenet
applications. Handle both these lock-step and split modes by propagating
mode and RPU core number(4 for RPU0 and 5 for RPU1) for various functions
and by adding conditions in those functions.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Linux commit f69629919942 ("dt-bindings: sram: Convert SRAM bindings to
json-schema") converted binding to yaml and some missing required
properties started to be reported. Align binding based on it.
The patch is fixing these warnings:
.../zynq-zc702.dt.yaml: sram@fffc0000: '#address-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: '#size-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: 'ranges' is a required property
>From schema: .../Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/87c02786ccd8d7827827a9d95a8737bb300caeb0.1606397101.git.michal.simek@xilinx.com
The Linux commit f8f79fa6bb25 ("dt-bindings: at25: convert the binding
document to yaml") converted binding to yaml and 3 deprecated properties
pop up.
The patch is fixing these warnings:
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'pagesize' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'size' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'address-width' is a required property
>From schema: .../Documentation/devicetree/bindings/eeprom/at25.yaml
by converting them to new binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/be2c1125d98386033e182012eb08986924707a76.1606397101.git.michal.simek@xilinx.com
Use the ZDMA channel 0 to initialize the DRAM banks. This avoid
spurious ECC errors that can occur when accessing unitialized memory.
The feature is enabled by setting the option
CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT and providing the following data:
SPL_ZYNQMP_DRAM_BANK1_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK1_LEN : len of memory to initialize (hex)
SPL_ZYNQMP_DRAM_BANK2_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK2_LEN : len of memory to initialize (hex)
Setting SPL_ZYNQMP_DRAM_BANK_LEN to 0 takes no action.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove the LED unit addresses and reg properties to
fix the following dtc build warnings:
arch/arm/dts/o4-imx-nano.dtb: Warning (reg_format): /leds/led@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
...
arch/arm/dts/o4-imx-nano.dtb: Warning (avoid_default_addr_size): /leds/led@0: Relying on default #address-cells value
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oleh Kravchenko <oleg@kaa.org.ua>
Linux uses the prefix "ethernet" whereas u-boot uses "eth". This is from
the linux tree:
$ grep "eth[0-9].*=.*&" arch/**/*dts{,i}|wc -l
0
$ grep "ethernet[0-9].*=.*&" arch/**/*dts{,i}|wc -l
633
In u-boot device trees both prefixes are used. Until recently the only
user of the ethernet alias was the sandbox test device tree. This
changed with commit fc054d563b ("net: Introduce DSA class for Ethernet
switches"). There, the MAC addresses are inherited based on the devices
sequence IDs which is in turn given by the device tree.
Before there are more users in u-boot and both worlds will differ even
more, rename the alias prefix to "ethernet" to match the linux ones.
Also adapt the test cases and rename any old aliases in the u-boot
device trees.
Cc: David Wu <david.wu@rock-chips.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the message "Invalid or missing layout file."
to debug level as it is a normal behavior and not an error
and add the missing '\n'.
This patch avoids the strange trace :
Boot over usb0!
Invalid or missing layout file.DFU alt info setting: done
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use get_cpu_dev() in uart getID command and remove the defines
DEVICE_ID_BYTE1 and 2 defines.
This patch prepare the support for new SOC family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Correctly handle number of alternate when DM_PMIC is not activated.
This patch remove the last UNKNOWN partition in this case.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Handle the second USB enumeration only when the flashlayout is received
and when phase is PHASE_FLASHLAYOUT. This patch removes the call of
stm32prog_next_phase as it is already done in stm32prog_dfu_init().
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When CONFIG_FIT_SIGNATURE is activated, CONFIG_LEGACY_IMAGE_FORMAT
is deactivated and the define IMAGE_FORMAT_LEGACY don't exist with
include/image.h:
#if defined(CONFIG_LEGACY_IMAGE_FORMAT)
#define IMAGE_FORMAT_LEGACY 0x01 /* legacy image_header based format */
#endif
This patch adds the needed check on compilation flag
CONFIG_LEGACY_IMAGE_FORMAT to avoid the compilation error
for command stm32prog:
cmd_stm32prog.c:81:8: error: ‘IMAGE_FORMAT_LEGACY’ undeclared
(first use in this function); did you mean ‘IMAGE_FORMAT_FIT’?
81 | if (IMAGE_FORMAT_LEGACY ==
| ^~~~~~~~~~~~~~~~~~~
| IMAGE_FORMAT_FIT
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the support in command stm32prog of kernel load and start
with initrd file, identify by the partition Type "Binary" in
the flashlayout.tsv, for example:
- 0x01 fsbl Binary none 0x0 tfa.stm32
- 0x03 fip Binary none 0x0 fip.bin
P 0x10 kernel System ram0 0xC2000000 uImage.bin
P 0x11 dtb FileSystem ram0 0xC4000000 board.dtb
P 0x12 initrd Binary ram0 0xC4400000 <initrd>
The <initrd> file can be a legacy image "uInitrd", generated
with mkimage, or a RAW initrd image "initrd.gz".
After a DFU detach the bootm command with be executed
with the associated address, for example:
$> bootm 0xC2000000 0xC4400000:<size> 0xC4000000
When the "Binary" partition type is absent, the 'bootm'
command starts the kernel without ramdisk, for example:
$> bootm 0xC2000000 - 0xC4000000
With this paths, it is no more mandatory to generate FIT
including the kernel, DT and initrd:
- 0x01 fsbl Binary none 0x0 tfa.stm32
- 0x03 fip Binary none 0x0 fip.bin
P 0x10 fit System ram0 0xC2000000 fit.bin
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Handle timeout in stm32prog_serial_get_buffer to sent NACK
to STM32CubeProgrammer when the buffer is not fully received.
This patch avoids to reach the STM32CubeProgrammer timeout and
the associated unrecoverable error.
Timeout error occurred while waiting for acknowledgment.
Error: Write Operation fails at packet number 4165 at address 0x1044FF
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch removes the header check for UART download;
the check of checksum is not mandatory with even parity and chuck
checksum for each 256 received bytes and it is only done for
STM32 image (FSBL = TF-A BL2), not for FIT image.
This patch solve issue of duplicated 0x100 byte written with FIP header.
Fixes: 4fb7b3e108 ("stm32mp: stm32prog: add FIP header support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
RK3568 is a high-performance and low power quad-core application
processor designed for personal mobile internet device and AIoT
equipments.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the SDMMC2 device tree node, as well as the pins it uses, in
U-Boot SPL.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable the SDMMC2 eMMC high-speed DDR mode as it is done in the
corresponding Linux kernel device tree.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Set the SDMMC2 VQMMC supply to vdd (buck3). Note that in the
corresponding Linux kernel device tree, the supply is set to v3v3
(buck4), which is wrong.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the “sdmmc2_d47_pins_d” pins to the SDMMC2 pinctrls. Increase the
bus width from four to eight.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The SDMMC2 interface hosts an eMMC. Replace the interface properties
that would only apply to SD cards—“broken-cd” and “disable-wp”—with
relevant ones: “non-removable”, “no-sd” and “no-sdio”.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDLD78cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLhSB/0UqOd+Ujf2meiHU9yr
oOOCLxVTjTUfIZKLad/zwlj2Xqzsjs6XMawC95BgouvkQLmj/gwerRWcZPg9l7/X
hvb9VJi+iJoLRRpBPbeF3bMb92kCE+YZodFXyutlcY+Z0ZB9755zoVgR6ccKfksd
Xp2y8AFptfYQNZ1l0yb3lhm1261CldWALrGTjRpY2hQ8nEMbV8z6WUB1hAF9CECa
PGbKaiqm9OdktwHsLy4cYFFCuzkykn6T3P6ODineP7IxgEgZKTfJClSTFGY9S0GQ
kwd7K/7j0W3rI5NPknB+Fb4IFAaTs/oozR+5ml7j+2S3G5GXjSGx8zaSOmOZvpP3
KxwN
=/I5V
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for the 2021.10 cycle:
This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
Change the USB erratum number A-050106 to A-050204 as A-050106 is
a duplicate and never be published.
Fixes 0cfa00cdb9 (“armv8: Add workaround for USB erratum A-050106”)
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Under DM, we rely on u-boot's device tree to provide the correct PHY
addresses. The board_fix_fdt callback is intended to be used for
device tree fixups before relocation. Unfortunately, this isn't an
option when booting from flash since the device tree isn't writable
before relocation.
This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a
board revision D or up is the target. The config option is used to set
the correct Aquantia PHY address in the board's u-boot device tree.
Defconfig files with the option enable explicitly are added for
convenience.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Address and size cells on SOC are set to 1. But gpio nodes are specified
with 2 cells. This fixes the gpio nodes to correct cells.
Signed-off-by: Lasse Klok Mikkelsen <lkmi@prevas.dk>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Read Linux PPFE firmware from flash partition and pass it to Linux through
FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs.
(FDT may increase at max by 64KB)
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For cpu release command, check whether PSCI is supported firstly,
if supported, use PSCI to kick off secondary cores, otherwise still
use spin table.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
[Fixed checkpatch alignment CHECKs]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Linux has had some stability issues when using AISRAM with a different
frequency from SRAM. Mirror their change here now that we relocate into
AISRAM.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Current logic in riscv_get_ipi() for Andes PLICSW does not look
correct. The mask to test IPI pending bits for a hart should be
left shifted by (8 * gd->arch.boot_hart), just the same as what
is done in riscv_send_ipi().
Fixes: 8b3e97badf ("riscv: add functions for reading the IPI status")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
At present the AE350 SPL defconfig is using OF_PRIOR_STAGE. The
intention was to use gdb to load device tree before running U-Boot
SPL/proper from RAM. When we switch to OF_SEPARATE we will have to
use our own DT but without "u-boot,dm-spl" in several essential
nodes, SPL does not boot.
Let's add all the required "u-boot,dm-spl" for SPL config.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
All the device nodes that refer to plic0 as their interrupt parent
have 2 cells encoded in their interrupts property, but plic0 only
provides 1 cell in #interrupt-cells which is incorrect.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
PLIC nodes don't have child nodes, so #address-cells is not needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
There are two spaces before "debug' in bootargs. Drop one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The SPDX license header is currently missing. Add one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
It was noticed that the clock isn't continuously enabled when there is
no link. This is because the 125MHz clock is derived from the internal
PLL which seems to go into some kind of power-down mode every once in a
while. The LS1028A expects a contiuous clock. Thus enable the PLL all
the time.
Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
R5 SPL needs access to cfg space of Rings and UDMAP, therefore add RING
CFG, TCHAN CFG and RCHAN CFG address ranges.
Note that these registers are present within respective IPs but are
not populated in Linux DT nodes (as they are configured via TISCI APIs)
and hence are added to -u-boot.dtsi for now.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-6-vigneshr@ti.com
MCU timer1 is used as the tick timer for MCU R5 SPL, and the
clock-frequency defined in DT appears to be incorrect at the moment.
Actual clock source for the timer is MCU_SYSCLK0 / 4 which is 250MHz.
Earlier setup of 25MHz went unnoticed, as there was a separate issue
with omap-timer, which caused an error to the clock by a factor of 8
with j7 devices. This problem surfaced once the omap-timer was fixed.
Signed-off-by: Tero Kristo <kristo@kernel.org>
Force the clk-k3 driver to probe early during R5 SPL boot to ensure the
default system clock configuration is completed. Many other drivers
assume a default state of the clock tree and it is currently possible
for them to probe before clk-k3 depending on the exact system
configuration.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Copy the contents of the board config loaded from sysfw.itb into an
EXTBOOT shared memory buffer that gets passed to sciserver. This only
needs to be done if EXTBOOT area has not been populated by ROM code yet.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Only start-up the non-linux remote cores if we are running in legacy
boot mode. HSM rearch is not yet supporting this.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
If the raw PM support is built in, we are operating in the split
firmware approach mode where PM support is not available. In this
case, skip the board config for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add callback routines for parsing the firmware info from FIT image, and
use the data to boot up ATF and the MCU R5 firmware.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add platform clock and powerdomain data for J721e and J7200. This data
is used by the corresponding drivers to register all the required device
clocks and powerdomains.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add DM (device manager) firmware image to the fit image that is loaded by
R5 SPL. This is needed with the HSM rearch where the firmware allocation
has been changed slightly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
board_fit_image_post_process() passes only start and size of the image,
but type of the image is not passed. So pass fit and node_offset, to
derive information about image to be processed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
On J7 family of SoCs (J721E and J7200), sysfw is being split to be run
under two cores, TIFS portion on DMSC core, and DM firmware under MCU
R5. As MCU R5 is also used to run one phase of the bootloader, we must
prevent access from here towards sysfw services. To support this, add
new config option which can be used to detect presence of RM/PM sysfw
services.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].
[1] https://github.com/Xilinx/embeddedsw
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add nodes for SPI NOR partitions to the device tree of Turris MOX, as
are in Linux' device tree.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add nodes for indicator LED and reset button so that board code can
implement board factory reset mechanism.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There have been some changes to the am335x-<board> DTs related to the
rtc node, so let's re-syncs them with Linux.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-7-dariobin@libero.it
For USB DFU boot mode there is a limitation on the load address of boot
images that they have to be less than 0x70001000. Therefore, move the
SPL_TEXT_BASE address to 0x70000000.
Currently ATF is being loaded at 0x70000000, if the SPL is being loaded at
0x70000000 then ATF would overwrite SPL image when loaded. Therefore, move
the location of ATF to a latter location in SRAM, past the SPL image. Also
rearrange the EEPROM and BSS data on top of ATF.
Given below is the placement of various data sections in SRAM
┌──────────────────────────────────────┐0x70000000
│ │
│ │
│ │
│ SPL IMAGE (Max size 1.5 MB) │
│ │
│ │
│ │
├──────────────────────────────────────┤0x7017FFFF
│ │
│ SPL STACK │
│ │
├──────────────────────────────────────┤0x70192727
│ GLOBAL DATA(216 B) │
├──────────────────────────────────────┤0x701927FF
│ │
│ INITIAL HEAP (32 KB) │
│ │
├──────────────────────────────────────┤0x7019A7FF
│ │
│ BSS (20 KB) │
├──────────────────────────────────────┤0x7019F7FF
│ EEPROM DATA (2 KB) │
├──────────────────────────────────────┤0x7019FFFF
│ │
│ │
│ ATF (123 KB) │
│ │
│ │
├──────────────────────────────────────┤0x701BEBFB
│ BOOT PARAMETER INDEX TABLE (5124 B)│
├──────────────────────────────────────┤0x701BFFFF
│ │
│SYSFW FIREWALLED DUE TO A BUG (128 KB)│
│ │
├──────────────────────────────────────┤0x701DFFFF
│ │
│ DMSC CODE AREA (128 KB) │
│ │
└──────────────────────────────────────┘0x701FFFFF
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-9-a-govindraju@ti.com
AM64 EVM board has a micro USB 2.0 AB connector and the USB0_VBUS is
connected with a resistor divider in between. USB0_DRVVBUS pin is muxed
between USB0_DRVVBUS and GPIO1_79 signals.
Add the corresponding properties and set the pinmux mode for USB subsystem
in the evm dts file.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-7-a-govindraju@ti.com
U-Boot either supports USB host or device mode for a node at a time in the
device tree nodes. To support both host and dfu bootmodes, dr_mode is set
to "peripheral" by default and then fixed based on the mode selected by
the boot mode config dip switches on the board.
This needs to happen before the cdns3 generic layer binds the usb device
to a host or a device driver. Therefore, use fdtdec_setup_board()
implementation to fixup the device tree property.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-4-a-govindraju@ti.com
Add support for providing ATF load address with a Kconfig symbol.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-2-a-govindraju@ti.com
Update the ddr settings to use the DDR reg config tool rev 0.5.0.
This enables 2666MTs LPDDR configuration on J7200.
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210603131453.11414-1-praneeth@ti.com
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
macro, which expands the value provided to the Hz range without taking into
account the precise Hz setting. This causes the frequency of 266 MHz not ot
be found in the imx8mm_fracpll_tbl, since it is entered there with a
precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
fracpll frequency cannot be determined.
Correct the value in imx8mm_fracpll_tbl to match the one expanded by
MHZ(266) macro, rounding it down to MHz range only.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.
Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.
Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Clock initialization functionality has ambitious debug messages, which are
printed out when failures are triggered during execution:
- Separate frequency table lookup functions have the the same output that
makes it impossible to understand which function failed and produced the
output
- PLL decoding routine has a generic debug statement printed, which does
not state the actual value failed to be found
Extend the output for both cases with prefixing table lookup functions
output with function name, and report the failed value in PLL decoding
routine.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
A simple prototyping board with one microSD port, one Ethernet port,
2 USB ports, I2C, SPI, GPIO, and UART interfaces.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
We need those macros to instruct drivers on how to behave for SoC specific
quirks, so let's add it as done for other i.MX SoCs.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
