xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYzGwogAKCRDKSWXLKUoM
Ial4AJ9+4WHn0MV2X7gK1fyh4lUW7ggPhQCggsYlSoACgMgdji17SAPhCv/W3IA=
=BmA9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc1-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1 (round 2)
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
By pressing "c" key during SPL execution, we force U-boot execution
instead of a kernel XIP image.
This fixes a hard fault when booting stm32f746-disco in SPL with "c"
key pressed during SPL execution.
U-Boot SPL 2022.10-rc5-00009-g40d02baa91 (Sep 20 2022 - 17:21:21 +0200)
Trying to boot from XIP
Hard fault
pc : 080083fc lr : 08000d1b xPSR : 21000000
r12 : 2004f108 r3 : 080083fd r2 : 00000028
r1 : 2004f0c8 r0 : 2004f0e4
Resetting CPU ...
This is due to SYS_UBOOT_START flag set to 0x080083FD which is not correct.
If unset, SYS_UBOOT_START is set by default to CONFIG_SYS_TEXT_BASE
which match with our requirement.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Waldemar Brodkorb <wbx@openadk.org>
Versal NET platform is based on Versal chip which is reusing a lot of IPs.
For more information about new IPs please take a look at DT which describe
currently supported devices.
The patch is adding architecture and board support with soc detection
algorithm. Generic setting should be very similar to Versal but it will
likely diverge in longer run.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/320206853dc370ce290a4e7b6d0bb26b05206021.1663589964.git.michal.simek@amd.com
This patch adds general board files based on MT7981 SoCs.
MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:
1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add general board files based on MT7986 SoCs.
MT7986 uses one mmc controller for booting from both SD and eMMC.
Both MT7986A and MT7986B use the same pins for spi controller.
Configs for various boot types:
1. mt7986_rfb_defconfig - SPI-NOR and SPI-NAND for MT7986A/B
2. mt7986a_bpir3_emmc_defconfig - eMMC for MT7986A only
3. mt7986a_bpir3_sd_defconfig - SD for MT7986A only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Remove the unnecessary comment after the CONFIG_SYS_BOOTM_LEN
migration to Kconfig.
Fixes: c45568cc4e ("Convert CONFIG_SYS_BOOTM_LEN to Kconfig")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Update the distro config env memory layout for the Verdin iMX8M Mini and
Verdin iMX8M Plus:
- loadaddr=0x48280000 allows for 128.5MB area for uncompressing (ie FIT
images, kernel_comp_addr_r, kernel_comp_size)
- fdt_addr_r = loadaddr + 127.5MB : allows for 127.5MB kernel
- scriptaddr = fdt_addr_r + 512KB : allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB : allows for 512KB script
Memory layout taken from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout") but moved loadaddr by an
additional 0.5MB to avoid "Moving Image from 0x48200000 to 0x48280000"
during booti plus actually defining kernel_comp_size to make booti work.
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Erase the entire U-Boot area during U-Boot update instead of just
a subset of it. This way, in case u-boot-with-spl.imx grows, the
sf write won't write over non-erased part of the SPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
* Drop legacy /boot/PPTImage.md5 check
* Update device tree naming
* Update t30args#0 root cmd line property to support latest kernel
versions (root=/dev/mmcblk0p2 for linux < 4 and
root=/dev/mmcblk1p2 for linux >= 4)
* Add custom bootloader version string
* Destroy invalid dtb at ${dtbaddr} and configuration script at
${cfgaddr} to ensure proper boot in warm restart case.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Commit 0ea4fc4dcf ("board/BuR: invalidate ${dtbaddr} before cfgscr")
destroys the boot targets b_t30lgcy#0 and b_t30lgcy#1. The reason behind
this is, that b_t30lgcy#0 and b_t30lgcy#1 both load the for booting
needed device trees from mmc and the cfgscr script patches those. Because
of this, cfgscr is not allowed to destroy the previously loaded device
tree otherwise cfgscr will fail.
This patch moves the device trees invalidation on warm restart to the
PREBOOT cmd to fix that issue.
Fixes: 0ea4fc4dcf ("board/BuR: invalidate ${dtbaddr} before cfgscr")
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The SPI and NAND board variants never went into production.
Drop those board variants.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
These macros are not used anymore in microblaze code since commit
f113d7d303 ("Convert CONFIG_SPL_STACK to Kconfig"), so remove them.
Fixes: f113d7d303 ("Convert CONFIG_SPL_STACK to Kconfig")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-1-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
$fdt_addr is mandatory for systems which provides DTB in HW (e.g. ROM) and
wishes to pass that DTB to Linux.
Turris Mox contains DTB binary in SPI NOR memory at "dtb" partition which
starts at offset 0x7f0000 and is 0x10000 bytes long.
Armada 3700 CPU does not allow mapping SPI NOR memory into physical address
space like on other architectures and therefore set $fdt_addr variable to
memory range in RAM and loads this DTB binary from SPI NOR in misc_init_r()
function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmMZoW4ACgkQ4rK92eCq
k3W2MAgAsmy2aSlMYo/AGlJ/KCrZuk6OirNHtdOdacvbcdUUbpkNpBSjdkrRm2If
VUnY1utIIJe6gFgnBUxXJ3RF5FZuhkdawc6V25HtDp6H3WamzJknKs5Vc4TlKp59
hZCOto7/+G/cd2XLdCKFUBl+new1pdDPsEm56+57DeZ7QGAQRX35PUQ5+HBjQJ/N
n/wJgS6wkEdIQLLwmCVxbHUkC+pRotTza5F2A0qZJgYPMcMpVFYKtzIa4GbWB5YS
MKGHbM8f3C8RLPQaHHTRycoA2Yor1I52B4Oi7605c5zHQr9pjrgtWsernDzkIhsB
ThYHSYQBUBTY4HBfzFwzCkVGqqLWNg==
=PMFY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220907' of https://source.denx.de/u-boot/custodians/u-boot-stm
- simplify the STM32MP15x package parsing code
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
Correctly calculate offsets between SPL and proper U-Boot when new config
option CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR for generating eSDHC boot sector
is enabled. Otherwise SPL would not be able to boot proper U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
All *boot env commands overrides default boot source location via i2c.
After board reset without power off, BootROM then starts booting U-Boot
from this specified location instead of the default one.
Add new env command defboot which reverts boot location to the default
value, which in most cases is configurable by HW DIP switches.
And add new env commands norlowerboot, norupperboot, sd2boot to boot from
other locations. norlowerboot would instruct BootROM to boot from lower NOR
bank, norupperboot from upper NOR bank and sd2boot from SD card with
alternative configuration.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SYS_HZ_CLOCK was wrongly set to 1GHz whereas it's set to 750MHz
by default by bootrom.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Grzegorz Szymaszek <gszymaszek@short.pl>
The frequency of the system counter is static which is given by the
COUNTER_FREQUENCY option. Remove COUNTER_FREQUENCY_REAL.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This converts CONFIG_SYS_L2_PL310 to Kconfig.
For omap2 and mvebu the 'select SYS_L2_PL310' locations were
determined using ./tools/moveconfig -i CONFIG_SYS_L2_PL310.
For mx6 I manually chose ARCH_MX6 as 'select' location. The
correctness has been verified using
$ ./tools/moveconfig.py -f ARCH_MX6 ~SYS_L2_PL310 ~SYS_L2CACHE_OFF
0 matches
That means whenever an ARCH_MX6 board had SYS_L2_PL310 disabled, this
was correctly reflected in SYS_L2CACHE_OFF. Thus it's safe to insert
the 'select' statement under ARCH_MX6.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
This removes the following symbols:
CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS
CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS
CONFIG_SYS_I2C_LDI_ADDR
CONFIG_SYS_I2C_DVI_ADDR
CONFIG_SYS_I2C_DVI_BUS_NUM
They are unused by any code in tree at this time.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_EEPROM_CCID
CONFIG_SYS_I2C_EEPROM_NXID
CONFIG_SYS_EEPROM_BUS_NUM
Signed-off-by: Tom Rini <trini@konsulko.com>
Just enabling the Kconfig option for DM_ETH and DM_MDIO is enough.
Additionally, we can remove the old hardcoded config.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
If something is wrong with the environment, we cannot rely on a proper
u-boot operation anymore. In fact, it is possible, that we never reach
misc_init_r() with a broken environment.
Also don't enable the netconsole by environment settings. This way the
user don't have to reconfigure the environment. Instead the network
console is only enabled when the push button is pressed during boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the common kernel_addr_r, ramdisk_addr_r and fdt_addr_r variable
names.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
We can load the ramdisk as the last step. This way we don't have to set
the intermediate variable 'ramdisk_len' and can remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Drop our own CONFIG_FDTFILE handling in favor of the generic
CONFIG_DEFAULT_FDT_FILE one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add distro boot to board include file and deconfig file
- Miscellaneous changes:
- Remove Gerald from maintainer list (email bounced)
- Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy
kernel method of booting (e.g. OpenWrt) with appended DTB.
- Add CONFIG_UBIFS_SILENCE_MSG to reduce binary size.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220807192709.21717-1-pali@kernel.org/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
- Add distro boot to board include file and deconfig file
- Miscellaneous changes:
- Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy
kernel method of booting (e.g. OpenWrt) with appended DTB.
- Add CONFIG_LTO and CONFIG_UBIFS_SILENCE_MSG, and disable some
unused configs to reduce binary size.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220807192709.21717-1-pali@kernel.org/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The kmtegr1 board is out of maintenance and can be removed. As it is the
only board in the tree using MPC8309 the support for this CPU is dropped
completely.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
This board is missing migration to CONFIG_DM, which had a deadline of
v2020.01, which is now more than 2 years passed due. Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we are about to enable DM_ETH by default, remove legacy code.
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have been orphaned for some time and are behind on various
DM migrations. Remove them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is not converted to use CONFIG_DM, well passed the migration
deadline. Remove it.
Cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The LS1043ARDB rev v7.0 board replaces the AQR105 PHY on MAC9 with an
AQR113C PHY. The address of the PHY on the MDIO bus changes from 0x1 to
0x8. Enable CONFIG_OF_BOARD_FIXUP and update both u-boot and Linux device
trees to reflect this change.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
This driver has not been converted to DM_ETH. The migration deadline
passed 2 years ago.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
This converts the following to Kconfig:
CONFIG_FSL_NGPIXIS
CONFIG_SYS_FSL_QMAN_V3
CONFIG_SYS_FSL_RAID_ENGINE
CONFIG_SYS_FSL_RMU
CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
CONFIG_SYS_FSL_SRIO_LIODN
CONFIG_SYS_FSL_TBCLK_DIV
CONFIG_SYS_FSL_USB1_PHY_ENABLE
CONFIG_SYS_FSL_USB2_PHY_ENABLE
CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
And we remove the entries from the README for a number of already
converted items.
Signed-off-by: Tom Rini <trini@konsulko.com>
Only two boards in the tree set the macro DWC_NET_PHYADDR. Both have
CONFIG_DM_ETH_PHY=y, so should set the phy address in DT if necessary.
The imx8mp_evk does set the correct address in device tree.
The other board seems to be a copy-paste-adapt from an old
version of the imx8mp_evk config header, given the "#ifdef
CONFIG_DWC_ETH_QOS" block that has been removed from imx8mp_evk header
in commit 127fb45495. Its device tree doesn't even enable (i.e., set
'status = "okay"') the &eqos node. But the other ethernet device,
&fec, does get enabled, and does have a phy sitting at address 4 (and
it also has a corresponding legacy #define CONFIG_FEC_MXC_PHYADDR
4). So I believe it should be completely safe to remove it from there
as well.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[trini: Re-apply to top of tree, update imx93_evk.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
There are a large number of options under CONFIG_SYS (but some of these
are elsewhere, spotted while cleaning CONFIG_SYS) that are never
referenced, or only used slightly later in the config file. Remove or
restructure these.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FLASH_ERASE_TOUT
CONFIG_SYS_FLASH_LOCK_TOUT
CONFIG_SYS_FLASH_UNLOCK_TOUT
CONFIG_SYS_FLASH_WRITE_TOUT
In practice, for two m68k platforms we move to hard-coding with a
comment the timeout values, rather than try and make convoluted Kconfig
logic. We add options for the write and erase options to the pic32
flash driver, as this driver does make use of them. Everywhere else
these are unreferenced values.
Signed-off-by: Tom Rini <trini@konsulko.com>
All platforms today define CONFIG_SYS_DDR_RAW_TIMING, so drop the code
for this option being unset.
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is the only platform defining and using CONFIG_SYS_MEM_SIZE, switch
to using CONFIG_SYS_SDRAM_SIZE for consistency.
Cc: Paul Burton <paul.burton@mips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a number of CONFIG_SYS_xxx_SIZE options to describe the amount
main memory available. Rework CONFIG_SYS_DDR_SIZE, which described a
size in number of MiB to use CONFIG_SYS_SDRAM_SIZE which is most often
used as a number of bytes. Use shifts of this option when required.
Signed-off-by: Tom Rini <trini@konsulko.com>
No platforms enable the functionality to tftp directly to NOR flash, and
this is discouraged by the documentation. Remove this code. Further,
this highlights an oddity of the code. Un-indent the start of this
function.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now when CONFIG_SYS_TEXT_BASE has sane value, use it for calculation of
other SPL offset values: CONFIG_SPL_MAX_SIZE, CONFIG_SYS_MMC_U_BOOT_* and
CONFIG_SYS_SPI_FLASH_U_BOOT_* macros.
No functional change.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
FEC_QUIRK_ENET_MAC is defined in the imx-regs.h include file and thus
does not need to be defined in the various board config includes.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add support for 96Boards Dragonboard 845C aka Robotics RB3 development
platform. This board complies with 96Boards Open Platform Specifications.
Features:
- Qualcomm Snapdragon SDA845 SoC
- 4GiB RAM
- 64GiB UFS drive
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/sdm845.rst, board: dragonboard845c.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The macro `CONFIG_SYS_UBOOT_BASE` is used by SPL loaders `"NOR"` and
`"XIP"` to determine the base address of u-boot.
For `"NOR"` on i.MX8MM it is the base address of QSPI0 plus the offset
of the flattened image tree blob.
Although `QSPI0_AMBA_BASE` is used to define CONFIG_SYS_UBOOT_BASE in
multiple board header files for i.MX8MM, it is not specified.
Specify offset of flattened image tree blob (needs to be set to same
value as specified in 'binman' node), base address of QSPI0 and size of
FlexSPI configuration block.
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This allows to compile U-Boot without some boot option for some A3720 board
which does not have that peripheral.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
For mostly historic reasons we had configuration headers for each
Allwinner CPU "family". These days they are mostly just including one
common header, with the rest being somewhat empty.
There were attempts to remove them, and to just use the one common header
to begin with, but this has implications to the build system, which me
might not be ready for, yet.
To document this behaviour, and to avoid something sneaking in over
time, make those files all the same (minus the CPU family name and
the copyrights), and add a comment explaining that.
This makes it easier to just remove those files later on, when needed
and possible.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds support for MediaTek MT7621 SoC.
All files are dedicated for u-boot.
The default build target is u-boot-mt7621.bin.
The specification of this chip:
https://www.mediatek.com/products/homenetworking/mt7621
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmLNj88ACgkQ4rK92eCq
k3Wukwf+PZnmQuyzwwFDOpZO1lUPfUN0WkoEBV8M5IxLehHdfHJT3YsAtm6DS8dd
4+n0+WmR7Uk4B8ODRPrGNBJftFoOVfEAvWmpfCC/VcHgEDEzdJzJe6yxa9wAWeQR
djRZLM8qx6OIEUW+sfYbFkD2BCv+cLiT0YH9qqx8WCRlf6JTuLquSBJQXIJAqYiE
LdO/pp0rv4oC0s08BSL4bHL/Mh7FHeUPiEjn2uRP/vISgmH1qyCql3gbr/wCaTYR
jfqr9pjmWTxEOppZIdE832QMy1MTSA/6Q3Jr4LKRko6ArBGjbGlj3EbeeEdKPDRy
BtQ6OLnxWKdcPr2qp301nnERRi4L4w==
=WgbW
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220712' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Alignment with Linux kernel device tree v5.19 for stm32mp15 and stm32mp13
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
MPS3 board have a ISP1763 usb controller, enable it to be used
for mass storage access for example. Enable the usb command
also and for the FVP support for mass storage enable the mmc
command.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
On STM32MP13x STMicroelectronics boards, the UART can reliably go up to
4000000 bauds when connected to the external ST-LINKV3.
This patch adds the support of higher baudrates on STMicroelectronics
STM32MP13x boards with ST-LINKV3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Correctly handle STM32MP_BOARD_EXTRA_ENV define in stm32mp15_st_common.h;
the STM32MP_BOARD_EXTRA_ENV is added in CONFIG_EXTRA_ENV_SETTINGS
definition, as it is done "stm32mp15_st_common.h"
Without this patch, the content of STM32MP_BOARD_EXTRA_ENV is not used in
the default environment for STMicroelectronics boards.
Fixes: 806c4dd315 ("configs: stm32mp1: set the console variable for extlinux.conf")
Reported-by: Gatien CHEVALLIER <gatien.chevallier@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On p1_p2_rdb_pc platforms, we set ddr_data_init to the "poison" value of
0xdeadbeef rather than a real calculated / derived value. Do this
directly and comment rather than via CONFIG.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a single platform that is both in the OMAP3 family of parts, but
has an EMIF4 memory controller. Currently we hard-code the size of
chip select 0. Make this more clear by putting the value in the
function rather than a CONFIG option.
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix multiple issues in ubifs distroboot code:
U-Boot supports attaching only one MTD device as UBI at the time. So
always call 'ubifsmount ubi0:${bootubivol}' for mounting UBI volume
${bootubivol}. Usage of 'ubi${devnum}' is incorrect as 'ubi part'
command attach MTD device always as UBI device ubi0.
Set distroboot ${bootfstype} variable to ubifs in ubifs_boot command.
Distroboot scripts require ${bootfstype} variable to be properly set and it
is already set for all other boot types.
Set distroboot ${distro_bootpart} variable to ${bootubivol} value. UBI
device does not have partitions, but has volumes. Distroboot scripts
require something to be set in ${distro_bootpart} variable, so set it to
the UBI volume which is currently mounted by ubifs.
Set distroboot ${devnum} variable to fixed string "ubi0". ubifs code
differs from the other partition code that it requires "ubi" prefix before
number.
Explicitly unmount ubifs volume after loading all data from it. This allows
to detach UBI device from MTD device.
Move definition of MTD device with UBI and UBI volume with ubifs filesystem
from global env variables ${bootubipart} and ${bootubivol} into the
distroboot "func" macro, defined in board include config files. UBIFS
distroboot macros then set ${bootubipart} and ${bootubivol} local variables
for compatibility with existing distroboot scripts.
This last change allows to define more UBIFS target devices and make it
clear what is boot MTD/UBI device.
All board include config files are adjusted to use this new scheme of
specifying boot MTD/UBI device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
This converts the following to Kconfig:
CONFIG_SYS_BOOTM_LEN
As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
We only reference CONFIG_SYS_BFTIC3_BASE in one location. Move the
comment to where we reference it, and use the value directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
As this is used in the environment, reference it directly rather than as
a CONFIG value.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Adrian Alonso <adrian.alonso@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
Signed-off-by: Tom Rini <trini@konsulko.com>
All of these symbols are not referenced anywhere else in the code, so
remove them.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
On platforms that use CONFIG_USB_OHCI_NEW we do not need to set
CONFIG_SYS_USB_OHCI_REGS_BASE nor CONFIG_SYS_USB_OHCI_SLOT_NAME. Drop
these from platforms that we can.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point, the only user of ohci-hcd that also uses PCI is using DM,
so we can drop CONFIG_PCI_OHCI* usage. No platforms set either of
CONFIG_SYS_USB_OHCI_BOARD_INIT or CONFIG_SYS_USB_OHCI_CPU_INIT so those
hooks can be removed as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_OHCI_SWAP_REG_ACCESS
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
CONFIG_SYS_USB_OHCI_SLOT_NAME
CONFIG_USB_ATMEL
CONFIG_USB_ATMEL_CLK_SEL_PLLB
CONFIG_USB_ATMEL_CLK_SEL_UPLL
CONFIG_USB_OHCI_LPC32XX
CONFIG_USB_OHCI_NEW
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_KIRKWOOD_EGIGA_INIT
CONFIG_KIRKWOOD_PCIE_INIT
CONFIG_KIRKWOOD_RGMII_PAD_1V8
CONFIG_KM_DISABLE_PCIE
Signed-off-by: Tom Rini <trini@konsulko.com>
These CONFIG options are only used on this board, in the board file
itself. Remove these from the CONFIG namespace and define in the board
file.
Signed-off-by: Tom Rini <trini@konsulko.com>
The symbol CONFIG_PCI_CLK_FREQ is local to this board. Provide equal
clarity in the code by referencing the numeric value directly and move
the explanatory comment to the code, just prior to use.
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver is not enabled anywhere, remove it. Also remove definitions
of symbols only used in this driver, on platforms that did not enable
it.
Signed-off-by: Tom Rini <trini@konsulko.com>
As things stand currently, there is only one PowerPC platform that
enables the options for CHAIN_OF_TRUST. From the board header files,
remove a number of never-set options. Remove board specific values from
arch/powerpc/include/asm/fsl_secure_boot.h as well. Rework
include/config_fsl_chain_trust.h to not abuse the CONFIG namespace for
constructing CHAIN_BOOT_CMD. Migrate all of the configurable addresses
to Kconfig.
If any platforms are re-introduced with secure boot support, everything
required should still be here, but now in Kconfig, or requires migration
of an option to Kconfig.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SAMSUNG_ONENAND
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
We rename the S5P specific "CONFIG_PWM" to CONFIG_PWM_S5P and move it to
Kconfig. Given the usage of CONFIG_PWM_NX, we have that select this new
symbol.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- Drop the emulator CONFIG test from include/configs/ls1088ardb.h
- Migrate CONFIG_SYS_FSL_DDR_EMU to a select'able option in
drivers/ddr/fsl/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
As this driver can dynamically determine the values set in
CONFIG_DW_WDT_BASE when using WDT, so make this depend on WDT rather
than migrate CONFIG_DW_WDT_BASE to Kconfig.
Cc: Chee Tien Fong <tien.fong.chee@intel.com>
Cc: Chin-Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinh.nguyen@intel.com>
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Stefan Roese <sr@denx.de>
Cc: hee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This value is always used at the default, rename it for now. This
likely should come from the device tree if non-default, moving forward.
Signed-off-by: Tom Rini <trini@konsulko.com>
From whole P1/P2 family of RDB boards is TDM-PMC card (PCI Mezzanine Card,
Freescale PQ-MDS-T1) available only on P1021RDB and P1025RDB boards.
So address mapping for TDM-PMC card on LBC should not be enabled on any
other P1/P2 RDB board as there is no device at that TDM-PMC address.
Support for P1021RDB and P1025RDB boards was already removed from mainline
U-Boot in commits 6d1dd76afe ("board/freescale: Remove P1021RDB board
support") and d521cece5a ("board/freescale: Remove P1025RDB board
support").
So do not enable TDM-PMC address mapping on remaining P1/P2 RDB boards and
remove all macros related to TDM-PMC address mappings.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add defconfig and Kconfig files for Google Chameleon V3 board
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The configs ROCKCHIP_CHIP_TAG and ROCKCHIP_MAX_INIT_SIZE were
originally added with rksd.c, rkspi.c and rkcommon.c in mind,
but are no longer in use and replaced by struct spl_info,
so remove unused configs for tag and size.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move the environment text over from being set via
CONFIG_EXTRA_ENV_SETTINGS in include/configs/gw_ventana.h and over
to plain text in board/gateworks/gw_ventana/gw_ventana.env. This lets
us drop CONFIG_EXTRA_ENV_SETTINGS_COMMON as everything resides in a
single environment file now.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
- Ensure that everyone setting mtdids= and mtdparts= is doing so via the
CONFIG options.
- If the CONFIG options are set, ensure that the default environment
sets mtdparts / mtdids.
Signed-off-by: Tom Rini <trini@konsulko.com>
The "autoload" environment variable is always checked with env_get_yesno
as it can be set to any form of no. The default behavior of
env_get_yesno is to return -1 on variables that are not set, which acts
as true in general (we test for non-zero return). To convert
CONFIG_SYS_AUTOLOAD to Kconfig, given that it was almost always used to
set autoload to no, first rename to CONFIG_SYS_DISABLE_AUTOLOAD for
consistency sake. Then, make it so that if enabled we set autoload=0 in
the default environment. Migrate all platforms which set
CONFIG_SYS_AUTOLOAD to non-true or that set autoload to false in their
default environment to using CONFIG_SYS_DISABLE_AUTOLOAD
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the environment text over from being set via
CONFIG_EXTRA_ENV_SETTINGS in include/configs/opos6uldev.h and over to
plain text in board/armadeus/opos6uldev/opos6uldev.env. This lets us
manage env_version without a CONFIG variable.
Cc: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_RANGE
Now that this is in Kconfig we can enforce a minimum size and so remove
the check in C code to ensure range is larger than size.
Signed-off-by: Tom Rini <trini@konsulko.com>
With the exception of distro_boot support, we can move all of the rest
of the environment changes to come from CONFIG_EXTRA_ENV_TEXT and in
turn remove CONFIG_ENV_REFLASH.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This define is only currently used in a single board, and always set to
one. Define this within the board code and remove other references.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_MIN_ENTRIES
CONFIG_ENV_MAX_ENTRIES
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the exception of how PowerPC handles SPL and TPL (which has its own
issues), we cannot safely hide options under CONFIG_SPL_BUILD. Largely
remove the places that have this test today.
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce board/siemens/common/Kconfig and have it hold FACTORYSET to
start with. Use select for this on the boards that need it.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Following how it's done for the majority of drivers, add a new
VIDEO_EXYNOS option and Kconfig file under drivers/video/exynos and list
the current options there.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since bb5930d5c9 ("exynos: video: Convert several boards to driver
model for video") there have been no callers of any of the exynos_lcd_*
family of functions. Remove these from the boards, and then remove
unused logo and related code as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
The only platform currently that defines an ide_preinit function has an
empty one that immediately returns. Remove this hook.
Signed-off-by: Tom Rini <trini@konsulko.com>
The migration deadline for this has passed and all boards have been
updated, remove this legacy code and references for it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The migration deadline for this has passed and all boards have been
updated, remove this legacy code and references for it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The only use of CONFIG_XTFPGA was to build all of the in-tree device
trees. Switch to using CONFIG_XTENSA instead of a non-Kconfig symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
Passing the mtdparts environment variable to the Linux kernel is
required to properly mount the UBI rootfs.
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The Linux kernel device tree already specifies the device to be used for
boot console output with a stdout-path property under /chosen.
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
Replace XILINX_DCACHE_BYTE_SIZE macro with two Kconfig symbols for
instruction and data caches sizes, respectively:
CONFIG_XILINX_MICROBLAZE0_ICACHE_SIZE
CONFIG_XILINX_MICROBLAZE0_DCACHE_SIZE
Also, get rid of the hardcoded value in icache_disable().
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-8-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com> (s/bralid/brlid/g)
CONFIG_SYS_INIT_SP_OFFSET macro place stack to TEXT_BASE - SYS_MALLOC_F_LEN
but there is no reason to do it now because board_init_f_alloc_reserve()
returns exact location where stack should be. That's why stack location is
calculated at run time and there is no need to hardcode it via macro. This
change will help with placing U-Boot to any address.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e9aee69646e022fd8a96cbee2d2a07ab81fb6e05.1655299267.git.michal.simek@amd.com
Do not use 0 as address for memory because of the special meaning for
pointers (null pointer). Change the spl bss start address to the second
page.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220607074314.27125-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmKsehgACgkQ4rK92eCq
k3UexAf+JThCd7FlN3OkTVKIdZKeNm2KpQxrqt20whiqp/nSUzxXrjdlCTKZEER2
lLJoVnwr+bkmdlqsa6gAZXSsd0lUv37XnLsLA5or278tFNlKp6gzYrz49FR59mVC
ie7/NlY5FgM5qmKGCob7tjwJ78r2/S3T2EaLiAMWUmw2UB5KZU6h3napHZ+1T0se
vaEAVRzAaZeYzKU3k6RBSv2tXQ6ssvfpp9RcXpRGtrN908AqDhHiOfntuOrnsEe0
9rjY1DSXO9a5WqHRm2KQ3FrA/By2layQ+4WH/HgIPHasisnmo3E/euVWmhtTaiT/
g5bOLwyFQ2/RvdMlMxXlKUcuMfNwRA==
=Hhzj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220620' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Add STM32MP13 SoCs support with associated board STM32M135F-DK
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
Code for changing boot source is platform generic and can be used by any
P1* and P2* compatible RDB board. Not only by boards which use config
header file p1_p2_rdb_pc.h.
So move this code from p1_p2_rdb_pc.h to p1_p2_bootsrc.h and cleanup macros
for generating boot source env variables in CONFIG_EXTRA_ENV_SETTINGS.
This allows to use code for resetting board and rebooting to other boot
source also by other boards in future.
Signed-off-by: Pali Rohár <pali@kernel.org>
Replace reference to the correct name STMicroelectronics
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove STM32_SYSRAM_END and clean the comments in stm32mp15_common.h file
after moving some CONFIG to Kconfig: CONFIG_SYS_CBSIZE,
CONFIG_SPL_MAX_FOOTPRINT, CONFIG_SYS_SPL_MALLOC_START and
CONFIG_SYS_SPL_MALLOC_SIZE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Introduce the code in mach-stm32mp and the configuration file
stm32mp13_defconfig for the new STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When migrating CONFIG_CONS_INDEX to Kconfig, on this platform we changed
what "board" evaluated to in the environment. This in turn meant that
we would no longer try and find the correct fdtfile via the normal
distro boot logic. Fix this by overriding board in the default
environment, as done on other platforms where CONFIG_SYS_BOARD is not
what we want to be in the board environment variable.
Fixes: f76750d111 ("Convert CONFIG_CONS_INDEX et al to Kconfig")
Reported-by: Gabriel Hojda <ghojda@yo2urs.ro>
Tested-by: Gabriel Hojda <ghojda@yo2urs.ro>
Signed-off-by: Tom Rini <trini@konsulko.com>
Clean up in ubiload script. Unmount UBIFS from which kernel image was
loaded and detach UBI on which the UBIFS is located, otherwise message
similar to the following is printed just before booting kernel:
Removing MTD device #7 (rootfs) with use count 1
Error when deleting partition "rootfs" (-16)
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
CONFIG_SPL_RAW_IMAGE_SUPPORT default y has been used to replace
CONFIG_SPL_ABORT_ON_RAW_IMAGE for quite some time, so drop
CONFIG_SPL_ABORT_ON_RAW_IMAGE.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_SPL_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart3 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_SPL_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm_beacon
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mn_beacon
Since these boards has CONFIG_DM_SERIAL and/or CONFIG_SPL_DM_SERIAL,
the legacy macro no need to be defined.
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Soeren Moch <smoch@web.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
systemd prints its messages on the last console= statement that it finds
in the kernel arguments. The current ordering sends the systemd messages
to tty1, by default this is the display.
Ensure that systemd sends its messages to the default UART, reorder the
console= statements accordingly.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add am62x_evm_r5_defconfig for R5 SPL and am62x_evm_a53_defconfig for
A53 SPL and U-Boot support.
To keep the changes to minimum. Only UART And SD boot related configs
are included. This should serve as good starting point for new board
bringup with AM62x.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[trini: Migrate a number of CONFIG symbols, have re-tested]
Tested-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is the initial support for Broadcom's ARM-based 47622 SOC.
In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.
The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
rootwait=1 is not a valid kernel boot parameters. According
to the documenation is only rootwait
rootwait [KNL] Wait (indefinitely) for root device to show up.
Useful for devices that are detected asynchronously
(e.g. USB and MMC devices).
Fix:
Unknown kernel command line parameters "rootwait=1", will be passed to user space.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
CONFIG_SPL_BOOT_DEVICE was made obsolete by
CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC,SATA,UART}.
CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI is the default so existing users of
CONFIG_SPL_BOOT_DEVICE can simply have the option removed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is needed on some Marvell SoCs when
booting from MMC. All existing usages of this have the same value so
make this the default and have the Kconfig option depend on SPL &&
MVEBU_SPL_BOOT_DEVICE_MMC.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases, when we don't use CONFIG_SPL_FRAMEWORK nor are we on
PowerPC using their specific SPL/TPL framework, we need to specify the
start.S file to use for these typically very constrained systems. Do
this within the Makefile logic, rather than introducing a string-based
CONFIG option, as this would get slightly complex to do in Kconfig for a
very limited number of users.
Signed-off-by: Tom Rini <trini@konsulko.com>
The address where the device tree will be passed in to U-Boot at is now
moved to the Kconfig file. If this is user configurable, it needs to be
exposed rather than hidden, and should probably be renamed as well.
Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_ARGS_ADDR
In doing so, we also consistently use this variable for SPL_OS_BOOT and
not CONFIG_SYS_FDT_BASE in some cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is mostly unused. In the case where it is currently used, it means
the same as CONFIG_SPL_PAD_TO, which is already set for the platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START
We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_RELOC_TEXT_BASE
CONFIG_SPL_RELOC_STACK
CONFIG_SPL_RELOC_MALLOC_ADDR
CONFIG_SPL_RELOC_MALLOC_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX7
platforms, and move the existing large comment from imx7_spl.h to
doc/imx/common/imx7.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX6
platforms, and move the existing large comment from imx6_spl.h to
doc/imx/common/imx6.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have GENERATED_GBL_DATA_SIZE to tell us how large the generated
global data is, so do not use a hard-coded value of 1024 for it.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the places where PowerPC references CONFIG_SYS_GBL_DATA_OFFSET it
does so as (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET). And
it defines CONFIG_SYS_GBL_DATA_OFFSET in the same manner that other
architectures define CONFIG_SYS_INIT_SP_OFFSET. Other architectures
define CONFIG_SYS_INIT_SP_ADDR as (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_INIT_SP_OFFSET) typically. Rename things within PowerPC for
consistency with other architectures.
Signed-off-by: Tom Rini <trini@konsulko.com>
This value is only referenced by PowerPC code in a way other than
directly as CONFIG_SYS_INIT_SP_ADDR. Switch to CONFIG_SYS_INIT_SP_ADDR
directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This value is only referenced by PowerPC code in a way other than
directly as CONFIG_SYS_INIT_SP_ADDR. Switch to CONFIG_SYS_INIT_SP_ADDR
directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases, we define CONFIG_SYS_INIT_SP_ADDR differently for SPL or
full U-Boot. This case should be making use of CONFIG_SPL_STACK, as
that's what that variable is for. In a few other cases we define
CONFIG_SPL_STACK directly to CONFIG_SYS_INIT_SP_ADDR, but do not need to
as the code handles this correctly, normally.
Signed-off-by: Tom Rini <trini@konsulko.com>
The definition of CONFIG_SPL_BOOTROM_SAVE is always a fixed
CONFIG_SPL_STACK + 4, while CONFIG_SPL_STACK is not constant. This
change will make it clear where the location is still, once
CONFIG_SPL_STACK moves to Kconfig.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of PowerPC platforms define this, for SPL. To move this to
Kconfig, it needs to be CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE, so use
CONFIG_IS_ENABLED() to check for usage. A number of layerscape
platforms bring this logic from PowerPC, but only need a small part of
it, for the fman driver. Remove their unused portion at least.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_SYS_MALLOC_SIMPLE
The problem here is that a few platforms have been doing:
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
instead of defining CONFIG_SPL_SYS_MALLOC_SIMPLE directly. Correct this
and update the documentation in a few places to match usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_INIT_MINIMAL
CONFIG_SPL_FLUSH_IMAGE
CONFIG_SPL_SKIP_RELOCATE
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only referenced in non-SPL_DM cases, of which there are
currently none. Remove this option and slightly re-organize the code is
there is now never an if/else at the start of spl_sata_load_image()
Signed-off-by: Tom Rini <trini@konsulko.com>
This is always defined to 2, and referenced in two places. Move the
define to <asm/omap_common.h> and make sure the code that uses this
includes that file. Make <asm/arch-omap*/clock.h> not include that
file, as we don't need to be doing so.
Signed-off-by: Tom Rini <trini@konsulko.com>
Set kernel_comp_addr_r and kernel_comp_size for compressed kernel.
Adjust existing addresses for ramdisk, so that kernel_comp_addr_r
comes before the ramdisk image, since the decompressed kernel size
is known to us. This way we can allow big ramdisk image to be loaded.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Set kernel_comp_addr_r and kernel_comp_size for compressed kernel.
Adjust existing addresses for ramdisk, so that kernel_comp_addr_r
comes before the ramdisk image, since the decompressed kernel size
is known to us. This way we can allow big ramdisk image to be loaded.
Update unleashed.rst to remove the manual environment configuration
for compressed kernel boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Move kernel_comp_addr_r to an address that comes before the ramdisk
image, since the decompressed kernel size is known to us. This way
we can allow big ramdisk image to be loaded.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYo4bYwAKCRDKSWXLKUoM
IYmTAJ9t4GDXggJ7ErB3Kk7/qSrywjEGAgCgnKQVgQvjo1B6o5aiwbk1wR86zkQ=
=W7X8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
Use the de10-nano files as templates for the de10-standard board.
The files in qts directory are generated by quartus from the GHRD
design.
Signed-off-by: Humberto Naves <hsnaves@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Use phy address from device tree instead of CONFIG_FEC_MXC_PHYADDR from
board header. This is required, because the DH picoITX and DRC02 boards
require different settings than PDK2. The corresponding 'phy-handle'
device tree properties are already there.
I tested this change on picoITX and DRC02, but on PDK2 it is untested.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.
The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.
[1] Commit 6192cf8ac082 from
git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Enable CONFIG_SPL_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
FEC_QUIRK_ENET_MAC is defined in the imx-regs.h include file and thus
does not need to be defined in the various board config includes.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX8MP SoC FEC needs to have the FEC_QUIRK_ENET_MAC defined.
Fixes: commit 2395625209 ("board: gateworks: venice: add imx8mp-venice-gw740x support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX8M based Venice boards all have device-tree fec nodes that
use proper dt with a phy-handle pointing to a phy with reg assigned
to the proper phy address.
There is no need to keep using the CONFIG_FEC_MXC_PHYADDR hack when
a proper dt is used - remove it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This converts the following to Kconfig:
CONFIG_MTD_CONCAT
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
As stm32f46-disco, stm32f769-disco and stm32746g-eval are very similar
except their respective device tree file. These 3 boards uses the same
TARGET_STM32F746_DISCO flag (so same include/configs/stm32f746-disco.h
and same board file board/st/stm32f746-disco/stm32f746-disco.c)
To be able to compile these 3 boards, replace the hard-coded device-tree
name in include/configs/stm32f746-disco.h by CONFIG_DEFAULT_DEVICE_TREE
which is set in each board defconfig file with the correct value.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This allows to concatenate spl and u-boot binaries together.
Previously, both binaries has to be flashed separately at the correct
offset (spl at offset 0 and u-boot at offset 0x8000).
With this patch, only one binary is generated (u-boot-with-spl.bin)
and has to be copied in flash at offset 0 using openocd for example
or simply copied in exported mass storage.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On STMicroelectronics boards, the UART can reliably go up to
2000000 bauds when connected to the on-board ST-LINK-V2 for STM32MP15
Unfortunately U-Boot will fall back to 115200 unless higher rates are
declared via CONFIG_SYS_BAUDRATE_TABLE.
This patch add the support of higher baudrates on STMicroelectronics
boards with ST-LINK.
Cc: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Set the environment variable "console", used in extlinux.conf file when it
is generated by YOCTO distribution with:
UBOOT_EXTLINUX_CONSOLE ??= "console=${console},${baudrate}"
With these 2 variables, U-Boot give dynamically the used console and
baudrate in the Linux kernel bootargs.
For the STMicroelectronics boards, the used console is ttySTM0.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
For CONFIG_DM_SERIAL it is required to increase CONFIG_SYS_MALLOC_F_LEN as
default value is not enough for memory hungry CONFIG_DM_SERIAL code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Currently, in case of arm64 bootloader and U-Boot the stack pointer is
initialized at an offset of NON_SECURE_MSRAM_SIZE from arm64 SPL's text
base address. After jumping to arm64, execution is done out of DDR.
Therefore, having an offset corresponding to the size of MSRAM does not
have any significance.
Instead, initialize the stack pointer after an offset of 4MB from the SPL
text base address. This helps in allocating larger memory for stack.
┌────────────────────┐0x80080000
│ │
│ arm64 SPL │
├────────────────────┤
│ ▲ │
│ │ │
│ STACK │
├────────────────────┤0x80480000
│ Memory for Load │
│ Buffer Allocation │
├────────────────────┤0x80800000
│ │
│ U-Boot Image │
│ │
└────────────────────┘
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This patch enables the Kconfig symbols needed for full ethernet support
on the EBB7304. Also the PHY autonegotiation timeout is increased, as
the default 5 seconds are sometime a bit short. With this, ethernet can
be used on this board. Here an example of a tftp load:
=> tftp ffffffff81000000 big
ethernet-mac-nexus@11800e0000000 Waiting for PHY auto negotiation to complete....... done
Using ethernet-mac-nexus@11800e0000000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.243
Filename 'big'.
Load address: 0xffffffff81000000
Loading: ################################################## 10 MiB
13.2 MiB/s
done
Bytes transferred = 10485760 (a00000 hex)
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves CONFIG_SYS_INIT_SP_OFFSET to a higher address so that
it does not interfere with larger U-Boot images. This was noticed, while
adding network support to the EBB7304 board.
Signed-off-by: Stefan Roese <sr@denx.de>
The Zyxel NSA310s board has the network chip Marvell Alaska 88E1318S.
Use uclass mvgbe and the compatible driver M88E1310 driver to bring
up Ethernet.
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Remove CONFIG_RESET_PHY_R.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add phy mode RGMII to kirkwood-nsa310s.dts
- Miscellaneous changes: Move constants to .c file and remove header file
board/zyxel/nsa310s/nsa310s.h, add support for large USB and SATA HDDs,
use BIT macro, add/cleanup comments, and cosmetic changes.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220412201820.10291-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
U-Boot for Turris Omnia is always compiled with MMC, SCSI and USB support,
so always enable macros for booting from these devices.
Signed-off-by: Pali Rohár <pali@kernel.org>
CONFIG_ETHPRIME defines primary ethernet device and env variable $ethact
stores currently active ethernet device.
So there is no point to set ethact= in default environment. Instead set
CONFIG_ETHPRIME properly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Replace hardcoded i2c hex values for NOR banks by named SW macros in
map_lowernorbank/map_uppernorbank env commands.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Replace hardcoded boot i2c bus num and address by existing macros when
generating env for CONFIG_EXTRA_ENV_SETTINGS.
Same macros are used in U-Boot board code when reading information from
boot i2c data.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Do not stringify env $vscfw_addr two times (once implicitly via string
operator "" and second time explicitly via __stringify() macro) and allow
to compile U-Boot without CONFIG_VSC7385_ENET (when __VSCFW_ADDR was not
defined and so macro name was stringified into CONFIG_EXTRA_ENV_SETTINGS).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As written in comment, P2020 has two possible SD switch configurations.
Extend code to detect both of them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With the commit that moves the BOOTCOMMAND to Kconfig:
970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
some stray ifdefs have been left in the header files which
are now useless.
Clean up the include files to remove these lines.
Fixes: 970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
On Layerscape platforms, the DTB is loaded from boot filesystem,
per the fdt_addr description in doc/README.distro, it must be
removed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enough space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
CONFIG_MMCROOT is only used to set mmcroot, no need a dedicated macro.
Script as below
"
for i in `ls include/configs/*.h`
do
mmcroot=`sed -n '/define.*MMCROOT/ p' $i | awk -F\" '{ print $2;}'`
if [ ! -n "$mmcroot" ]; then
continue
fi
sed -i '/define.*MMCROOT/ d' $i
sed -i 's,\" CONFIG_MMCROOT \",'$mmcroot',g' $i
done
"
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Sancloud BeagleBone Enhanced Extended WiFi (BBE Extended WiFi) has
its own devicetree file and the board can be identified by the 2nd
letter of the config string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The Sancloud BeagleBone Enhanced Lite (BBE Lite) has its own devicetree
file and the board can be identified by the 2nd letter of the config
string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-By: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This GPIO is actually an input "Q7_3V3_PCIE_WAKE#_IN" not an output, so
remove the misleaading and incorrect definition.
Cc: Tim Harvey <tharvey@gateworks.com> (re: pci: imx: use vpcie-supply if defined by device-tree)
Signed-off-by: Ian Ray <ian.ray@ge.com>
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Remove CONFIG_RESET_PHY_R symbol from all board files
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The Colibri PXA270 has been end-of-life since quite a while and would
require more and more maintenance (e.g. DM conversions).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable USB support for host controller and various USB ethernet
devices.
Example usage of USB Mass Storage (UMS) support:
u-boot=> mmc list
FSL_SDHC: 0
FSL_SDHC: 1
FSL_SDHC: 2 (eMMC)
u-boot=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe30000
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use PREBOOT as well. This allows a customer to just set fdt_board as
on any other module to customize the device tree for his carrier
board.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop optional support for the ancient Apalis iMX6 V1.0 hardware which
had the UART wired as DCE rather than DTE.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop legacy nfsboot script in favor of distroboot DHCP boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use the same name of DHCP Distroboot script as in regular eMMC case.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Include SCSI in the list of boot targets if CONFIG_CMD_SCSI is
enabled.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Drop legacy #define CONFIG_DRIVER_DM9000 from board include/configs/
and enable the same in Kconfig configs/ .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The IMX_FEC_BASE value is not used when CONFIG_DM_ETH is configured. So this
value can be removed.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update the 'boot_net' script to load the fdt with the kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since we envision using overlays for display interfaces, the video=
settings within vidargs are obsolete. Remove these settings from the
U-Boot.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
All the other NAND-based boards have tdxargs specified for setting
manual kernel command-line arguments.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The COUNTER_FREQUENCY is missed in 8ulp configs, it will cause SPL
and u-boot not set the cntfrq_el0. For u-boot, this is ok, because
ATF has set it. But for SPL, it will lead delay and get_timer
not working.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because the Beacon imx8mn board uses device tree
for MMC/SD and Ethernet, there is no need to have some of the
config options. It's handled by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Because the Beacon imx8mm board uses device tree
for MMC/SD and Ethernet, there is no need to have some of the
config options. It's handled by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Based on current usage, migrate a number of DP-DDR related options to
Kconfig.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform has CONFIG_ETH_DESIGNWARE set already, which is the
correct value for the driver in question. Remove this incorrect line.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move these two options to the arch Kconfig file.
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
This symbol is only possibly useful on some mvebu platforms, so move the
symbol there and select it for the only current user.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a little tricky since SoCFPGA has code to determine this as
runtime. Introduce a guard variable for platforms to select if they
have a static value to use. Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONS_SCIF0
CONFIG_CONS_SCIF1
CONFIG_CONS_SCIF2
CONFIG_CONS_SCIF4
CONFIG_CONS_SCIFA0
Signed-off-by: Tom Rini <trini@konsulko.com>
These values are only used in one file, reference them more directly.
Cc: Kamil Lulko <kamil.lulko@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This code is only used on the corvus platform, so migrate the LED on/off
code to this platform and remove it from the CONFIG namespace. In
theory, this should likely be moved to the modern GPIO LED driver as a
further cleanup.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
A number of CONFIG options are used on these platforms as part of the
default environment. Set some of these more directly and in other
cases, just reference them directly.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CM_INIT
CONFIG_CM_REMAP
CONFIG_CM_SPD_DETECT
CONFIG_CM_MULTIPLE_SSRAM
CONFIG_CM_TCRAM
We make the first three of these options be always enabled, as that
matches usage. We select the last two based on how they were defined in
armcoremodule.h. This also allows us to remove some unused code in
board/armltd/integrator/lowlevel_init.S
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is only enabled for CI_UDC and !TEGRA20, so implement it as
such in Kconfig directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
This converts the following to Kconfig:
CONFIG_BOARD_SIZE_LIMIT
To do this, introduce CONFIG_HAS_BOARD_SIZE_LIMIT.
Signed-off-by: Tom Rini <trini@konsulko.com>
Up till now the CONFIG_POWER_TPS65217 has been defined in several header
files for am335x SoC.
This patch renames it to CONFIG_PMIC_TPS65217, which better reflects the
role of this IC circuit.
Moreover, new CONFIG_PMIC_TPS65217 has been introduced in Kconfig
to be used with boards, which both support DM_PMIC and DM_I2C.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Migrate all other platforms as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
=HOoS
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- Rearrange defconfig option order
- Add CONFIG_SAVE_PREV_BL_* options
- Doc updates:
- remove wrong SBOOT memory corruption note, because
memory is changed during u-boot bringup process,
not by SBOOT
- put payload on ramdisk place in abl boot image
creation step
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- strip unneeded config options
- add FIT image support
- add framebuffer node, u-boot logo and video console
- increase LMB_MAX_REGIONS, to store all linux dtb reserved memory regions
- add linux kernel image header
Uart driver causes hang, when u-boot is used in android boot image instead
of linux. Temporary disable console driver, until investigated and fixed.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
We already support the NVMe commands and PCIe backend in the QEMU target,
so let's make it easy for anyone to consume them and enable NVMe distro
boot along the way!
With this patch, I can put an NVMe backed disk image into my QEMU VM and
have it automatically load a UEFI target blob.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] 5b70c1f679/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
This command's functionality is now completely implemented by the
standard fs load command. Convert the vexpress64 boot command (which is
the only user) and remove the implementation.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The ARMv8-R64 architecture introduces optional VMSA (paging based MMU)
support in the EL1/0 translation regime, which makes that part mostly
compatible to ARMv8-A.
Add a new board variant to describe the "BASE-R64" FVP model, which
inherits a lot from the existing v8-A FVP support. One major difference
is that the memory map in "inverted": DRAM starts at 0x0, MMIO is at
2GB [1].
* Create new TARGET_VEXPRESS64_BASER_FVP target, sharing most of the
exising configuration.
* Implement inverted memory map in vexpress_aemv8.h
* Create vexpress_aemv8r defconfig
* Provide an MMU memory map for the BASER_FVP
* Update vexpress64 documentation
At the moment the boot-wrapper is the only supported secure firmware. As
there is no official DT for the board yet, we rely on it being supplied
by the boot-wrapper into U-Boot, so use OF_HAS_PRIOR_STAGE, and go with
a dummy DT for now.
[1] https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[Andre: rebase and add Linux kernel header]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add MAINTAINERS entry for Peter]
In preparation for the ARMv8-R64 FVP support, which has DRAM mapped at
0x0, generalise the page table generation, by using symbolic names for
the address ranges instead of fixed numbers.
We already define the base of the DRAM and MMIO regions, so just use
those symbols in the page table description. Rename V2M_BASE to the more
speaking V2M_DRAM_BASE on the way.
On the VExpress memory map, the address space right after 4GB is of no
particular interest to software, as the whole of DRAM is mapped at 32GB
instead. The first 2 GB alias to the lower 2GB of DRAM mapped below 4GB,
so we skip this part and map some more of the high DRAM, should anyone
need it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far the FVP model just supports booting through semihosting, so by
loading files from the host the model is running on. This allows for
quick booting of new kernels (or replacing DTBs), but prevents more
featureful boots like using UEFI.
Enable the distro_boot feature, and provide a list of possible boot
sources that U-Boot should check:
- For backwards compatibility we start with semihosting, which gets its
commands migrated from CONFIG_BOOTCOMMAND into the distro_boot
infrastructure. This is also slightly tweaked to fail graceful in case
the required files could not be found.
- Next we try to use a user provided script, that could be easily
placed into memory using the model command line.
- Since we gained virtio support with the enablement of OF_CONTROL,
let's check virtio block devices next. This is where UEFI boot can
be easily used, for instance by providing a distro installer .iso
file through virtio-blk.
- Networking is now provided by virtio as well, so enable the default
PXE and DHCP boot flows, mostly because we can.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The definition of the standard environment variables (kernel_addr_r and
friends) has been improved lately for the FVP model, but the Juno board
is still using some custom scheme.
Since we need to extend this to a third board soon, let's unify the
definition:
- Define the Juno addresses in the same generic way we do for the FVP
model, and move the actual variable setting out of the board #ifdef's.
- Add the missing addresses for a PXE file and a boot script.
- Cleanup some stale comments on the way.
As the FVP model doesn't have support for distro_boot quite yet, add
a dummy definition for now, to be replaced with the real thing later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE
Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NORFLASH_PS32BIT
Note that we also attempt to correct the behavior of the code here,
which had been testing for "NORFLASH_PS32BIT" which would never be set,
instead check for the now set "CONFIG_NORFLASH_PS32BIT", which results
in some behavior change.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_USE_NANDFLASH and CONFIG_SYS_USE_MMC serve the
same purpose as CONFIG_SD_BOOT / CONFIG_NAND_BOOT so migrate to using
these switches instead as they're already in Kconfig.
Cc: Stelian Pop <stelian@popies.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of M5373EVB we always had NANDFLASH_SIZE=16, so just use it
directly. In the case of M5329EVB we had not removed the rest of NAND
support when saying we didn't have NAND, so instead use that to key off
of rather than NANDFLASH_SIZE.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The value CONFIG_DB_784MP_GP is only used in the DDR code to refer to
CONFIG_TARGET_DB_MV784MP_GP so just use that second value directly.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We only set one of these values ever at this point, so remove dead code.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
There are a handful of variants around CONFIG_SYS_USE_DATAFLASH and none
of them now control anything further within their board config.h files,
so remove these from CONFIG_SYS_EXTRA_OPTIONS and then remove the empty
blocks in the board config.h files. In a few places further clean up
related logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LPUART
CONFIG_LPUART_32B_REG
And note that CONFIG_LPUART_32B_REG is unused in code.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one place, so pick a more direct name and
migrate to Kconfig. Rework the code slightly.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MCFRTC
CONFIG_SYS_MCFRTC_BASE
While at it, remove '#undef RTC_DEBUG' from these config files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Both of these variables are used in a few hard-coded ways to set some
string values or print something to the user. In almost all cases, it's
just as useful to hard-code the value used. The exception here is
printing something closer to correct board name for p1_p2_rdb machines.
This can be done using something from the device tree, but for now
hard-code a non-CONFIG based value instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTM_NETBSD
CONFIG_BOOTM_RTEMS
CONFIG_DESIGNWARE_WATCHDOG
CONFIG_DISPLAY_CPUINFO
CONFIG_DM_ETH
CONFIG_DM_MMC
CONFIG_DM_REGULATOR
CONFIG_DM_SPI
CONFIG_DM_SPI_FLASH
CONFIG_ISO_PARTITION
CONFIG_OF_SEPARATE
CONFIG_SPI_FLASH_WINBOND
CONFIG_SPL_ETH
CONFIG_TIMER
CONFIG_USB_DWC3
CONFIG_USB_DWC3_GADGET
CONFIG_USB_DWC3_OMAP
CONFIG_USB_DWC3_PHY_OMAP
CONFIG_USB_EHCI_TEGRA
CONFIG_USB_GADGET_DOWNLOAD
CONFIG_USB_GADGET_DUALSPEED
CONFIG_USB_GADGET_MANUFACTURER
CONFIG_USB_GADGET_PRODUCT_NUM
CONFIG_USB_GADGET_VBUS_DRAW
CONFIG_USB_GADGET_VENDOR_NUM
This catches a number of cases where board config files were #undef
various CONFIG options when building SPL, and that doesn't work. Clean
up the related comments as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The SPL does not update the memory node with the dram size from EEPROM
but instead we can use get_ram_size which does a simple memory test
to determine the available RAM. Update PHYS_SDRAM_SIZE to 4GiB as that
is the max used on the Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The 2x256 MiB SF variant of this system has 192 MiB rootfs MTD partition
containing UBI on SF0, use the correct size in U-Boot environment, else
U-Boot cannot mount UBI and boot on this variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VIDEO_BCM2835
This is the final ad-hoc CONFIG_VIDEO_... to convert.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FAULT_ECHO_LINK_DOWN
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91_WANTS_COMMON_PHY
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LEGACY
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91_GPIO_PULLUP
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This variable is used once and is noted as board-specific. Use the
value directly with a comment.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is used only once, and in comparison with an unset symbol,
so drop it.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G10EK
CONFIG_AT91SAM9261EK
CONFIG_AT91SAM9G10
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G20EK
CONFIG_AT91SAM9260EK
CONFIG_AT91SAM9G20EK_2MMC
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AM335X_USB0
CONFIG_AM335X_USB0_MODE
CONFIG_AM335X_USB1
CONFIG_AM335X_USB1_MODE
We do this by introducing specific options for static configuration of
USB0/USB1 in SPL rather than defining CONFIG_AM335X_USBx_MODE to the
enum value being used. Furthermore, with how the code is used now we do
not need to have OTG mode exposed as an option here, so remove that.
Signed-off-by: Tom Rini <trini@konsulko.com>
With all boards now using DM_ETH we determine the value for
CONFIG_FEC_XCV_TYPE at run time, except in the case of the default
fall-back. Set the fallback directly now.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ETHPRIME
This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME
similar to other options that are not always set and control environment
variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts removes the following symbols:
CONFIG_HAS_ETH0
CONFIG_HAS_ETH1
CONFIG_HAS_ETH2
CONFIG_HAS_ETH3
This is because at this point, only the ids8313 platform was using the
code which was controlled by these symbols. In turn, this code already
performs error checking on being able to perform the device tree fixup.
Rather than convert these to Kconfig for a single platform, update the
code to not need these checks and remove them from all the platforms
they were unused on.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOT_RETRY_TIME
CONFIG_BOOT_RETRY_MIN
CONFIG_RESET_TO_RETRY
We also introduce CONFIG_BOOT_RETRY to gate these options, and clean up
the associated Makefile entry and C code for picking default values of
CONFIG_BOOT_RETRY_MIN.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ARMV8_SWITCH_TO_EL1
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
This converts the following to Kconfig:
CONFIG_ARMV7_SECURE_BASE
CONFIG_ARMV7_SECURE_MAX_SIZE
CONFIG_ARMV7_SECURE_RESERVE_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
As the CI test for stopping platforms from being merged that were
defining symbols that had Kconfig entries, a small number of symbols
needed to be migrated again. Do so, and catch two cases the README
should also have been updated but was not.
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit re-introduced a migrated CONFIG symbol to the board header
file. These changes should likely be handled via documentation instead,
as well.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We cannot define a CONFIG value here to ensure that the Kconfig value
isn't set wrong.
Fixes: 2c699fe0d3 ("configs: sunxi: Add common SUNIV header")
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch enables some configs that should be working on the Bob board,
based on what is observed to work on the Kevin board.
The Bob board uses an Embedded DisplayPort panel compatible with the
simple panel and Rockchip eDP drivers. Its backlight is controlled by
the Chromium OS Embedded Controller Pulse Width Modulator. Enable these
for the board.
Also set VIDEO_ROCKCHIP_MAX_{XRES,YRES} to 1280x800, the resolution of
its panel. This had to be done for the Kevin board, but it's untested if
this is actually necessary for Bob.
The Rockchip video driver needs to assert/deassert some resets, so also
enable the reset controller. RESET_ROCKCHIP defaults to y for this board
when DM_RESET=y, so it's enough to set that.
The Bob board has two USB 3.0 Type-C ports and one USB 2.0 Type-A port
on its right side. Enable the configs relevant to USB devices so these
can be used. This is despite a known issue with RK3399 boards where USB
de-init causes a hang, as there is a known workaround.
Some other rk3399-based devices enable support for the SoC's random
number generator in commit a475bef534 ("configs: rk3399: enable rng on
firefly/rock960/rockpro64"), as it can provide a KASLR seed when booting
using UEFI. Enable it for Bob as well.
The default misc_init_r() for Rockchip boards sets cpuid and ethernet
MAC address based on e-fuse block. A previous patch extends this on Gru
boards to set registers related to SoC IO domains as is necessary on
these boards. Enable this function and configs for it on Bob.
The microSD card slot on this board (and others based on Gru) is
connected to a GPIO controlled regulator (ppvar-sd-card-io), which must
be operable by U-Boot. Enable the relevant config option to allow this.
Bob boards also use the Winbond W25Q64DW SPI flash chip, enable support
for Winbond SPI flash chips in the board config so U-Boot can boot with
this chip.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
QSGMII PHY initialization should only be done for J721E EVMs and not for
J721E-SK boards. Therefore, fix the environment variables accordingly.
Also, by default remote processors should not be booted in U-Boot but
rather be left to the users to enable this by setting dorprocboot.
Therefore, remove dorprocboot that is being set by default.
Fixes: 5980925e2a ("include: configs: j721e_evm: Add support to boot ethfw core in j721e")
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Mechanically convert video_hw_init() function to UCLASS_VIDEO probe
callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.
As framebuffer base address is setup by the bootloader which loads U-Boot,
set plat->base to that fixed framebuffer address.
This change was tested in qemu n900 machine and is working fine.
What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.
Signed-off-by: Pali Rohár <pali@kernel.org>
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Currently, any u-boot bootloader for ti armv7 platforms using
DEFAULT_FIT_TI_ARGS to boot with a fitimage (boot_fit = 1)
doesn't boot when built with Yocto Poky (openembedded-core).
## Loading kernel from FIT Image at 90000000 ...
Could not find configuration node
ERROR: can't get kernel image!
Arago forked the kernel-fitimage class [1] and altered the
configuration nodes naming while adding the OPTEE support by
using FITIMAGE_CONF_BY_NAME by default [2].
The "upstream" kernel-fitimage class from openembedded-core still
add the "conf-" prefix for each configuration nodes [3].
The ITS file format (from doc/uImage.FIT/source_file_format.txt)
is not really accurate with the expected naming of these nodes.
But in practice the "conf-" prefix is widely used.
When the FIT image support has been added for ti armv7 platforms
the naming from Arago has been used [3]. Fix this issue by adding
the prefix expected by the ITS file generated by kernel-fitimage
class from openembedded-core.
[1] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=719ab1b2098bcdc59c249e3529fa82cb1b9130e6
[2] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=f23f2876a0cda89241d031bb7ba0b4256ed90035
[3] https://git.openembedded.org/openembedded-core/tree/meta/classes/kernel-fitimage.bbclass?h=yocto-3.1.13#n290
[3] 1e93cc8473
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Denys Dmytriyenko <denys@konsulko.com>
This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These particular values are not configurable and today we always set
CONFIG_SECURE_BL1_ONLY. Move these to where they're used in the code,
and drop from the CONFIG namespace.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Remove some code, primarily CPM2 related, that is now unused since the
removal of MPC8540/60ADS.
Fixes 3913191c8a ("powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().
Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The BOOT_TARGET_DEVICES list for distro_bootcmd was hard-coded to assume
that all boot devices are available/enabled in the configuration,
thus ignoring the actual config settings. The config_distro_bootcmd.h
header file specifically has compile-time checks to detect such problems.
To allow disabling USB, SCSI, etc. in custom lx2160a board configs,
make it depend on the config settings and use only the enabled features.
Signed-off-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Use the complete 512kb (4 blocks) nand partition reserved for u-boot
environment instead of just the first block, this allows the module to
have a working environment even if 3 blocks are bad.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Now that single defconfig can be used for booting J721E EVM and
SK, default device tree will not work for selecting dtb for
kernel. Update the findfdt env to select right dtb based on
board_name env variable.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
There are no boards that define CONFIG_SYS_RESET_ADDR, so drop the
remaining comments referencing it and also the config_whitelist.txt entry.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: thomas@wytron.com.tw
This driver adds support for the keyboard on Apple Silicon laptops.
The controller for this keyboard sits on an SPI bus and uses an
Apple-specific HID over SPI protocol. The packets sent by this
controller for key presses and key releases are fairly simple and
are decoded directly by the code in this driver and converted into
standard Linux keycodes. The same controller handles the touchpad
found on these laptops. Packets for touchpad events are simply
ignored.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert
to Driver Model and use uclass mvgbe and the compatible driver M88E1118R
to bring up Ethernet.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- As the result of the migration to Driver Model, this u-boot image has
grown substantially (about 100K, give or take). The old envs location
at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K).
- Miscellaneous changes: Move constants to .c file and remove header file
board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to
keep u-boot image under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Dockstar board has the network chip Marvell 88E1116R. Convert to
Ethernet driver model, and use uclass mvgbe and the compatible driver
M88E1118R to bring up Ethernet.
- Add CONFIG_DM_ETH and associated configs.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Add CONFIG_PHY_MARVELL to properly configure the network.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Miscellaneous changes: Move constants to .c file and remove
header file board/Seagate/dockstar/dockstar.h, use
CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, add CONFIG_HUSH_PARSER, use BIT macro, and cleanup comments.
- Note: This patch is a RESEND for a previous patch:
https://patchwork.ozlabs.org/project/uboot/patch/20210812051854.1340-2-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Miscellaneous changes: Move constants to .c file and remove header file
board/iomega/iconnect/iconnect.h. Add CONFIG_HUSH_PARSER, use BIT macro,
and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Globalscale Technologies Dreamplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network
port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned,
could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/dreamplug/dreamplug.h, cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE
Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is defined based on two other CONFIGs for all boards except sandbox
and durian.
For sandbox the value does not matter. For durian the value seems
excessive.
Drop the option completely, to simplify configuration and reduce the
number of things we need to convert to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_IDE_MAXBUS
CONFIG_SYS_IDE_MAXDEVICE
CONFIG_SYS_ATA_BASE_ADDR
CONFIG_SYS_ATA_STRIDE
CONFIG_SYS_ATA_DATA_OFFSET
CONFIG_SYS_ATA_REG_OFFSET
CONFIG_SYS_ATA_ALT_OFFSET
CONFIG_SYS_ATA_IDE0_OFFSET
CONFIG_SYS_ATA_IDE1_OFFSET
CONFIG_ATAPI
CONFIG_IDE_RESET
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move setting the default boot command to the
apalis/colibri_imx6_defconfig. It allows replacing the command
without code modification.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The Linux Kernel Image size for arm64 is still growing.
A Kernel with 54 MB at load address 0x80280000 overlaps
with fdt_addr at 0x83000000. So let's increase it to 0x84000000
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Commit 72d81360aa ("global: Convert CONFIG_LOADADDR to
CONFIG_SYS_LOADADDR") dropped the usage of LOADADDR and replaced it with
SYS_LOADADDR.
Use the correct macro in environment by replacing CONFIG_LOADADDR with
CONFIG_SYS_LOADADDR.
Fixes: d75ebf3482 ("imx: ventana: fix splash logo drawing")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Add fdt_addr_r fdtfile which used by distro boot, and cleanup legacy
environment variables.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
We changed to single flash.bin now. So dfu_alt_info should be modified
to reflect this change.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The PDK2 board is capable of running both 100M and 1G ethernet. However,
the i.MX6 has only one ethernet MAC, so it is possible to configure
either 100M or 1G Ethernet. In case of 100M option, the PHY is on the
SoM and the signals are routed to a RJ45 port. For 1G the PHY is on
the PDK2 board with another RJ45 port. 100M and 1G ethernet use
different signal pins from the i.MX6, but share the MDIO bus.
This SoM board combination is used to demonstrate how to enable 1G
ethernet configuration.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Use the complete 512kb (4 blocks) nand partition reserved for u-boot
environment instead of just the first block, this allows the module
to have a working environment even if 3 blocks are bad.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Adds support for SUNIV and the F1C100s.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Remove some pointless #ifdefs from this file, as there are quite too
many of them already.
Some definitions don't really hurt to have in any case, so remove the
pointless CONFIG_MMC guard around CONFIG_MMC_SUNXI_SLOT.
The BOARD_SIZE_LIMIT applies regardless of ARM64 or not (now), so remove
that guard as well. The maximum number of MMC devices does not depend on
CONFIG_ENV_IS_IN_MMC, so move that out to simplify the file.
Last but not least CONFIG_SPL_BOARD_LOAD_IMAGE serves no real purpose
anymore: it's unconditionally defined for all sunxi boards, and protects
nothing applicable outside of sunxi code anymore. Just remove it.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Field fail-safe u-boot update procedure for pg-wcom boards is defined and
implemented by patch: 59b3403.
This patch invokes the update procedure for pg-wcom-ls102x designs during
early misc_init_f execution.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The GoFlex Home board has the network chip Marvell 88E1116R.
Use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: use CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
With Ethboot support in SPL, network stack requires more BSS area, so
increase BSS max size to 16K
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Today the bootcount is not managed by the Linux kernel for STM32MP15 as
we don't have driver to update the used backup register in TAMP and the
recovery command still executes the normal bootcmd with
'altbootcmd=run bootcmd'.
So the bootcount feature is never used, the config CONFIG_BOOTCOUNT_LIMIT
and the associated environment variable 'altbootcmd' can be removed to
reduce the U-Boot size.
Each boards can re-enable this feature later in their defconfig, if it is
needed, with the expected backend, for example CONFIG_BOOTCOUNT_GENERIC
or CONFIG_BOOTCOUNT_ENV.
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the following to Kconfig:
CONFIG_AT91_EFLASH
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Prepare migration to Kconfig.
CONFIG_SYS_MAX_FLASH_BANKS_DETECT becomes boolean and
CONFIG_SYS_MAX_FLASH_BANKS define the MAX size, also used
for detection when CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
(CFI_MAX_FLASH_BANKS = CONFIG_SYS_MAX_FLASH_BANKS).
CONFIG_SYS_MAX_FLASH_BANKS become mandatory when
CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
The am335x-ice-v2 board's Ethernet ports can be configured
in 'MII' or 'RMII' mode to be connected to 'PRUSS' or 'CPSW'
Ethernet subsystems.
This patch sets the environment variable 'ice_mii' to
'mii' or 'rmii' accordingly. Based on that we choose the
appropriate board devicetree i.e. 'am335x-ice-v2.dtb' or
'am335x-ice-v2-prueth.dtb'.
Since there are 2 Ethernet ports with 2 modes, there can be 4
configurations but for now we consider both ports in different modes
to be an invalid configuration and prevent boot in that case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Amjad: use overlay instead of using new am335x-ice-v2-prueth.dtb]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make prueth_is_mii be marked __maybe_unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
BOOT_TARGET_DEVICES should only be added if the corresponding u-boot
command is enabled otherwise the build will fail.
Signed-off-by: Piotr Kubik <piotr_kubik@vp.pl>
These hardcoded values were calculated from CONFIG_SPL_TEXT_BASE macro. Now
this macro is configurable via Kconfig, so calculate values 0x0030/0x4030
at compile time via CONFIG_SPL_TEXT_BASE option. Values 0x0030/0x4030
represents offset of CONFIG_SPL_TEXT_BASE from address 0x40000000.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Memory layout in the comment is from Armada XP platform which uses load
address 0x40004030. DB-88f6720 is Armada 375 platform which uses same load
address as Armada 38x which is 0x40000030.
Currently SPL support for Armada 375 is unfinished and does not work. There
is missing Serdes initialization and DDR3 training code. So nobody noticed
that CONFIG_SPL_* options are not correct.
Fix at least CONFIG_SPL_TEXT_BASE constant and remove incorrect comments
about memory layout. So it is not misleading.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
After the conversion to DM the SD card shows up as 'mmc 2'
device.
Adjust the 'mmcdev' and the distro command 'func' accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Enable support for USB and USB storage on the UDOO Neo.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In AOSP, both VIM3 and VIM3L have 2 bootloader flavors,
depending on A/B enablement.
For example, for vim3l, the naming is:
- u-boot_kvim3l_noab.bin : legacy support
- u-boot_kvim3l_ab.bin : A/B support
Prepare a defconfig to support u-boot_kvim3_ab.bin and
u-boot_kvim3l_ab.bin.
This is identical to khadas-vim3{l}_ab_android but will be updated in
the next commit.
Also update partitioning tables for A/B support.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-4-mkorpershoek@baylibre.com
This allows us to define extra board variables, such as "board" and
"board_name".
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-2-mkorpershoek@baylibre.com
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-7-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze is one the last two users of the CONFIG_SYS_RESET_ADDRESS
macro (the other is arch/powerpc/cpu/mpc8xx/cpu.c, but the macro is not
defined anywhere in powerpc code, so it should be removed there too).
Replace CONFIG_SYS_RESET_ADDRESS usage in start.S with
CONFIG_SYS_TEXT_BASE. If the reset address should really be
user-configurable, a new Kconfig option could be added.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-6-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The memory layout is taken from the device tree passed to us by
m1n1, so there is no need to define this.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The SMSC driver is using the old driver model.
Init the virtio system in vexpress64.c so that the network device is
discovered.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Move env var address values to #defines so they can be reused elsewhere.
Rename env var names to those recommended in the README and modify
addresses to allow more space for the kernel.
Fix issue where fdt is called with invalid arguments when booting
without a ramdisk.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Rename from vexpress_aemv8a.h -> vepxress_aemv8.h as new FVPs may not be
v8-A. No change in behavior.
This is towards future work to enable support for the FVP_BaseR.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
When using a recent kernel with a bunch of compiled-in
stuff the kernel image easily becomes bigger than 8 MB
yielding this error:
Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Fix this by bumping to SZ_64MB.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
-----BEGIN PGP SIGNATURE-----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=YdSB
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request of efi-next
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
This converts the following to Kconfig:
CONFIG_JFFS2_DEV
CONFIG_JFFS2_LZO
CONFIG_JFFS2_NAND
CONFIG_JFFS2_PART_OFFSET
CONFIG_JFFS2_PART_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_88F5182
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_IS_OPENRD_CLIENT
CONFIG_BOARD_IS_OPENRD_ULTIMATE
CONFIG_D2NET_V2
CONFIG_FEROCEON
CONFIG_FEROCEON_88FR131
CONFIG_INETSPACE_V2
CONFIG_KW88F6192
CONFIG_KW88F6281
CONFIG_KW88F6702
CONFIG_NET2BIG_V2
CONFIG_NETSPACE_LITE_V2
CONFIG_NETSPACE_MAX_V2
CONFIG_NETSPACE_MINI_V2
CONFIG_NETSPACE_V2
CONFIG_SHEEVA_88SV131
At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.
Signed-off-by: Tom Rini <trini@konsulko.com>
The only place we use CONFIG_CPU_ARMV8 was in the arm_dcc serial driver.
Switch this to CONFIG_ARM64 today, and if in the future we need finer
granularity tuning here, a new CONFIG_SERIAL option needs to be
introduced.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one of two ways. The first way is that it
is defined to a static value, of an unsigned long size. The second way
is that it is defined to something, typically a function, to determine
this value at run time.
However, in a few cases that function returns a static value. Change
that to using the static value directly.
In the case of using something at run time, convert everything to using
a function of the same name and prototype. This will allow for further
cleanups.
Finally, we have a few cases where the function is just not used, so
drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_CLK_FREQ_C100 and CONFIG_SYS_CLK_FREQ_C110 are
only used in one place and not changed by the board config file. Move
these out of the CONFIG namespace and in to the CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish this conversion we need to add a symbols for
SPL_SYS_NAND_SELF_INIT and TPL_SYS_NAND_SELF_INIT as there are cases
there where we need to, or need to not, use that framework as things
stand.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of CONFIG_SYS_FDT_ADDR this was being used to modify the
default value of fdt_addr / fdt_addr_r, which is not something to expose
in this manner and is not otherwise done. The case of SYS_ENV_ADDR is
similar but only done on the pic32mzdask platform, for scriptaddr.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
This is removing unused defines and correcting the default value to be
0x0 as we are a hex symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.
For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.
For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
In order to do this conversion, expose this option to the user and
use "save" not "safe" in the text.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_RPMB
This fixes a few platforms where the option was not taking effect as
intended.
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used as part of configuring the default environment for a
number of platforms. However, it is always set to 1 and the only time
it is part of Kconfig, it is used in a hard-coded manner. Hard-code the
value in the environment instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VIDEO_LOGO
Note that this option depends on CONFIG_DM_VIDEO now, since cfb_console is
deprecated. The only relevant code is now in splash.c
Drop the check for DM_VIDEO in that file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable SPL support in Kconfig and add some related option in
rk3568_common.h
Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com>
Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
