We are now using an env_ prefix for environment functions. Rename these
other functions as well, for consistency:
getenv_vlan()
getenv_bootm_size()
getenv_bootm_low()
getenv_bootm_mapsize()
env_get_default()
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Even after memory free of phydev, priv is still pointing to the
obsolete address.
So update priv->phydev as NULL after memory free.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The GMAC in the RK3368 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3368-specific logic necessary to reuse this driver.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Set BM poll size once during priv probe and do not
overwrite it during port probe procedure. Pool is common for
all CP ports.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
TX drain in transmit procedure could cause issues due
to race between drain procedure and transmition of descriptor
between AGGR TXQ and physical TXQ.
TXQ will be cleared before moving to Linux by stop procedure.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
MVPP22 driver support 64 Bit arch and require BM pool
high address configuration.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove IRQ configuration from U-Boot PP driver.
U-Boot don't use interrupts and configuration of IRQ in U-Boot
caused crashes in Linux shared interrupt mode.
Also interrupt use is redundant in RX routine since a single RX
queue is used.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
MBUS driver were replaced by AXI in PPv22 and relevant
only for PPv21.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
U-boot use single physical tx queue with size 16 descriptors.
So aggregated tx queue size should be equal to physical tx queue
and cpu descriptor chunk(number of descriptors delivered from
physical tx queue to aggregated tx queue by one chunk) shouldn't be
larger than physical tx queue.
Fix:
Set AGGR_TXQ and CPU_DESC_CHUNK to be 16 descriptors, same as
physical TXQ.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Issue:
BM counters were overrun by probe that called per Network interface and
caused release of wrong number of buffers during remove procedure.
Fix:
Use probe_done and num_ports to call init and remove procedure
once per communication controller.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables padding of packets shorter than 64B in TX(set by default).
Disabling of padding causes crashes on MACCIATO board.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
A8K marvell SoC has two South Bridge communication controllers(CP0 and CP1).
Each communication controller has packet processor ports and MDIO.
On MACHIATOBin board ports from CP1 are connected to mdio on CP0.
Issue:
Wrong base address is assigned to MDIO interface during probe.
Fix:
Get MDIO address from PHY handler parent base address.
This should be refined in the future when MDIO driver is implemented.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch add GPIO configuration support in mvpp2x driver.
Driver will handle 10G SFP gpio reset and SFP TX disable. GPIO pins should
be set in device tree.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
In fsl_mc_ldpaa_exit(), in case of mc is booted and dpl is applied,
it should return earlier without executing dpbp_exit().
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Acked-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The environment variable "disable_giga" can now be used to disable
1000baseTx on the Micrel's KSZ9031.
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Added the AFE (Analog Front End) settings for stability to the
Broadcom Cygnus phy. This improves the time take to perform
auto negotiation.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
move to Kconfig:
CONFIG_BCM_SF2_ETH
CONFIG_BCM_SF2_ETH_DEFAULT_PORT
CONFIG_BCM_SF2_ETH_GMAC
Also modified defconfigs of all platforms that use these configs.
Signed-off-by: Suji Velupillai <suji.velupillai@broadcom.com>
Tested-by: Suji Velupillai <suji.velupillai@broadcom.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The correct option is PHY_MICREL_KSZ90X1, but some configs still
select the 9021 and 9031 options, which are deprecated.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There should be no longer be any ksz9000 users that pick up the PHY
driver from ksz8xxx, so remove ksz9000 remnants from there.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.
As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.
To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The register constants don't use the exact names that are used in the
TRM, so add comments that use the exact names so that it is clear what
register is being referred to.
https://www.atheros-drivers.com/qualcomm-atheros-datasheets-for-AR9331.html
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Marek Vasut <marex@denx.de>
phy_device_create(..) sets the addr of phy_device with a sane value.
There is no need overwrite it.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for enabling and disabling the clock using the clock
framework based on the content of OF instead of doing it manually
in the board file.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The order of parameters passed to the phy_connect() was wrong.
Moreover, only PHY address 0 was used. Replace this with code
capable of detecting the PHY address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for probing the RAVB Ethernet block from device tree.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
commit 306dd7dabd ("net: fec_mxc: fix PHY initialization bug with CONFIG_DM_ETH")
has broken the build of the fec_mxc driver with CONFIG_DM_ETH
enabled because it changed the parameters passed to *fec_get_miibus()
without changing the functions prototype.
This patch fixes up the prototype of fec_get_miibus() for the DM_ETH case.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Add missing .h and add missing declarations in .h
Declare local functions as static. Make interrupt_init_cpu function
signatures consistent with how decrementer_count is declared.
Based on warnings reported by 'make C=2'
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[trini: drop cpu_init_f as 8xx/83xx are different from the rest, rework
interrupt_init_cpu/decrementer_count]
Signed-off-by: Tom Rini <trini@konsulko.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
When CONFIG_DM_ETH is set, the FEC ethernet controller is reset after
the PHY has been set up and initialzed. This breaks the communication
with the PHY and results in an inoperable ethernet interface.
Do the initialization with CONFIG_DM_ETH in the same order as with
legacy ETH support to fix this.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This covers the Gigabit Ethernet MAC (i.e. common designware driver and
rockchip-specific wrapper).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000
and CMPC885 which are respectively based on MPC866 and MPC885 processors.
This patch adds support for the first board.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Commit a058052c changed the generic phy_reset() to clear all bits in
BMCR. This inevitably clears the ANEG bit. m88e1145 requires any
change to ANEG bit to be followed by a software reset. This seems to
be different from other PHYs. Implement read-modify-write procedure
for this PHY init.
Signed-off-by: York Sun <york.sun@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <hs@denx.de>
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
On MIPS systems DMA isn't coherent with the CPU caches unless an IOCU is
present. When there is no IOCU we need to writeback or invalidate the
data caches at appropriate points. Perform this cache maintenance in
the pch_gbe driver which is used on the MIPS Boston development board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use the virt_to_bus & bus_to_virt functions rather than phys_to_bus &
bus_to_phys, since the addresses accessed by the CPU will be virtual
rather than physical. On MIPS physical & virtual addresses differ as we
use virtual addresses in kseg0, and attempting to use physical addresses
directly caused problems as they're in the user segment which would be
mapped via the uninitialised TLB.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The loop to set up buffer addresses in rx descriptors always operated on
descriptor 0, rather than on each descriptor sequentially. Fix this in
order to setup correct buffer addresses for each descriptor.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Using the EG20T gigabit ethernet controller on the MIPS Boston board, we
find that we have to reset the controller in order for the RGMII link to
the PHY to become functional. Without doing so we constantly time out in
pch_gbe_mdio_ready.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Dont flush dummy descriptors as they are already
allocated from a region with dcache off. Tested
this on Zynq(zc702) and ZynqMP(zcu102) boards.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use wait_for_bit to be non breakable as using it with
breakable causes issue of un interruptible auto negotiation.
This is due to the ctrlc pressed will taken for wait_for_bit()
abort during phy_read() and hence not coming out of
auto negotiation.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The 88E1518 code is programming the wrong registers for rgmii-id,
rgmii-txid and rgmii-rxid interfaces.
Since the PHY defaults to rgmii-id, it would appear that the code
was previously only used with sgmii and rgmii-id interfaces.
Tested on 88E1512 PHY in rgmii-id mode which is from the same family
as 88E1518.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Abort CPSW driver init when auto-negotiation of link
times out. Currently, the code ignores return status
of phy_startup(), and goes ahead with network operation
(like DHCP) even though the link may be down.
Instead, abort init process if link is down or if there
is another error, so phy_startup() can easily be retried
again. This also helps quick fallback to next network interface
(like USB RNDIS) without inordinate delay.
Tested on AM571x IDK and AM335x BeagleBone black.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Always search the PHY to determine the macb->phy_addr before using
the PHY to fix "No PHY present" error.
Fix the wrong test of the GMAC's phy interface mode, it should be
PHY_INTERFACE_MODE_RGMII.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch fixes some remaining issues in the mvpp2 driver for the 10GB
support on port 0. These changes are:
- Incorrect PCS configuration
- Skip PHY configuration when no PHY is connected
- Skip GMAC configurations if 10G SFI mode set
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The .read_rom_hwaddr net_ops hook does not check the return value, which
is why it was never caught that we are currently returning 0 if the
read_rom_hwaddr function return -ENOSYS and -ENOSYS otherwise.
In this case we can simplify this by just returning the result of the
function.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Some board need a regulator for gmac phy, so add this code to handle it.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This change migrate the following configuration options for Kconfig:
* PHY_GIGE, indicates that a controller (with an appropriate PHY) is
Gigabit capable and enables extra support in the miiutil for
parsing the status of Gigabit PHYs
* adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
which previously had to enabled through a board-specific config file
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Previous to MC v10.x, port mac address was specified via DPL. Since
newer MC versions are compatible with old style DPLs, make the u-boot
env mac addresses visible there. This applies only to DPLs that have
an older version.
DPLs use 32 bit values for specifying MAC addresses. U-boot
environment variables take precedence over the MAC addresses already
visible in the DPL/DPC.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
DPAA2 platforms boot the Management Complex based on the u-boot env
variable "mcinitcmd". Instead of doing this step on each platform
individually, define a single mc_env_boot function in the MC driver,
since it's semantically tied to it.
Call the function in a per-board reset_phy hook, as it gets called at a
later moment, when all board PHY devices have been initialized.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
These two functions have an of_ prefix which conflicts with naming used
in of_addr. Rename them:
fdt_read_number
fdt_support_bus_default_count_cells
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
Adjust this function to us an ofnode instead of an offset, so it can be
used with livetree. This involves updating all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The of_ prefix conflicts with the livetree version of this function.
Rename it to avoid problems when we add livetree support.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present
Signed-off-by: Simon Glass <sjg@chromium.org>
Earlier when MC is loaded but DPL is not deployed results in FDT
fix-up code execution hangs. For this case now print message on
console and return success instead of return -ENODEV. This update
allows fdt fixup to continue execution.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <Priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add driver for the Renesas Ethernet AVB block found in RCar H3/M3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Based on work of:
Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Specify the registered eth index by dev_id.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Avoid transfer parameter dev_id value with "-1" to .fec_get_hwaddr(),
it should transfer fec->dev_id to get mac address from fuse.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The MIB RAM and FIFO receive start register does not exist on
i.MX6ULL. Accessing these register will cause enet not work well or
cause system report fault.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The variable netdev_ethtool_ops is not referenced, drop it. However
with gcc-6 or later we fail to even compile as we do not have the
required struct definition in U-Boot.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The variable 'res' may be unused uninitialized if our call to
mv88e61xx_port_read (register read) fails and we goto the error
handling section. In this case we set 'res' to -EIO to indicate why we
failed.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
To avoid the failure of mdio_register(), add the remove callback
to unregister the mii_dev when removing the ethernet device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fixed up unused variable warning, e.g. for gurnard:
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds a remove function to the mvpp2 ethernet driver which is
called before the OS is started, doing:
- Allocate the used buffers back from the buffer manager
- Stop the BM activity
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Convert CONFIG_RGMII to Kconfig. Thanks to that, it is possible to
update defconfig files of SYS_EXTRA_OPTIONS accordingly and
remove it when it is possible.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the SUNXI_EMAC config to Kconfig. Remove it from SYS_EXTRA_OPTIONS
from many sunxi defconfig and renamed it into SUN4I_EMAC to not confuse it
with SUN8I_EMAC.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the SUNXI_GMAC config option to Kconfig, remove it
from SYS_EXTRA_OPTIONS and rename it into SUN7I_GMAC.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These drivers have no user since commit ea3310e8aa ("Blackfin:
Remove").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
The intention of the removal is the preparation to introduce the
new AT91 PIO pinctrl driver.
Use the union to make the PIO3 and PIO2's registers be together
and make their offset aligned.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This ports the support for configuring a GPIO for resetting the
Ethernet PHY (incl. such details as the reset polarity and
pulse-length) from the Designware driver.
X-AffectedPlatforms: A64-uQ7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GMAC in the RK3399 is very similar to the RK3288 variant (i.e. it
is a Designware GMAC core and requires similar configuration as the
RK3288 to switch it to RGMII and set up the TX/RX delays for Gigabit).
The key difference is that the register offsets (within the GRF block)
and bit-offsets (within those registers) used to hold the configuration
differ between the various RK32/33 CPUs.
This change refactors the gmac_rockchip.c driver to use a function
table (selected via driver_data) to factor out these differences. Each
function's implementation then matches the underlying processor.
Some collateral changes are needed in the definitions describing the
bits and offsets in the GRF are needed to prefix each set of symbolic
constants with the SoC name to avoid name clashes... and in doing so,
the shifts for masks and constants have been moved into the header
files for readability (and to make it easier to stay below 80 chars).
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed commit message typo s/factor our/factor out/:
Signed-off-by: Simon Glass <sjg@chromium.org>
This includes Marvell mvpp2 patches with the ethernet support for the
ARMv8 Armada 7k/8k platforms. The ethernet patches are all acked by Joe
and he is okay with me pushing them via the Marvell tree.
As pointed out by Stefan Chulski, this variable is unused and should be
removed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On PPv2.2 we enable PHY polling, so we also need to configure the PHY
address in the specific PHY address rgisters.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Testing shows, that PHY polling needs to be enabled on Armada 7k/8k.
Otherwise ethernet transfers will not work correctly. PHY polling
is enabled per default after reset, so we do not need to specifically
enable it, but this makes it clearer.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a missing occurrance of PHY_INTERFACE_MODE_RGMII_ID, which should
be handled identical to PHY_INTERFACE_MODE_RGMII.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to
the Marvell mvpp2 ethernet driver for the missing port 0. This code is
mostly copied from the Marvell U-Boot version and was written by Stefan
Chulski. Please note that only SFI support have been added, as this
is the only interface that this code has been tested with. XAUI and
RXAUI support might follow at a later stage.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to
the Marvell mvpp2 ethernet driver. This code is mostly copied from the
Marvell U-Boot version and was written by Stefan Chulski. Please
note that only RGMII and SGMII support have been added, as these are
the only interfaces that this code has been tested with.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Read the "phy-speed" DT property to differentiate between 1 and 2.5GB
SGMII operations. Please note that its unclear right now, if this
DT property will be accepted in mainline Linux. If not, we need to
revisit this code and change it to use the accepted property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch does a bit of restructuring of the probe / init functions,
mainly to allow earlier register access as it is needed for the upcoming
GoP (Group of Ports) and NetC (Net Complex) code.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the PPv2.2 specific FIFO configuration to the mvpp2
driver. The RX FIFO packet data size is changed to the recommended
FIFO sizes. The TX FIFO configuration is newly added.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently, the naming of the ethernet ports is not handled correctly in
the multi-CP (Communication Processor) case. On Armada 8k, the slave-CP
also instantiates an ethernet controller with the same device ID's.
This patch now takes this into account and adds the required base-id
so that the slave-CP ethernet devices will be named "mvpp2-3 ...".
This patch also updates my Copyright notice to include 2017 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since Armada 7K/8K is also equipped with a newer version of the MVPP2
ethernet controller, lets enable compilation of this driver for these
platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes problems noticed with the PPv2.2 A7k/8k port, when not all
elements of the descriptors had been cleared before use.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch moves the base_probe function mvpp2_base_probe() from the
MISC driver to the ETH driver. When integrated in the MISC driver,
probe is called too early before the U-Boot ethernet infrastructure
(especially the MDIO / PHY interface) has been initialized. Resulting
in errors in mdio_register().
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In U-Boot the MDIO / SMI support is integrated in the mvpp2 driver,
currently only supporting the 32bit platforms (Armada 37x). This patch
now adds the A7k/8k PPv2.2 MDIO support to that the phy / mii IF
can be used as well on these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that the mvpp2 driver has been modified to accommodate the support
for PPv2.2, we can finally advertise this support by adding the
appropriate compatible string.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In PPv2.1, we have a maximum of 8 RXQs per port, with a default of 4
RXQs per port, and we were assigning RXQs 0->3 to the first port, 4->7
to the second port, 8->11 to the third port, etc.
In PPv2.2, we have a maximum of 32 RXQs per port, and we must allocate
RXQs from the range of 32 RXQs available for each port. So port 0 must
use RXQs in the range 0->31, port 1 in the range 32->63, etc.
This commit adapts the mvpp2 to this difference between PPv2.1 and
PPv2.2:
- The constant definition MVPP2_MAX_RXQ is replaced by a new field
'max_port_rxqs' in 'struct mvpp2', which stores the maximum number of
RXQs per port. This field is initialized during ->probe() depending
on the IP version.
- MVPP2_RXQ_TOTAL_NUM is removed, and instead we calculate the total
number of RXQs by multiplying the number of ports by the maximum of
RXQs per port. This was anyway used in only one place.
- In mvpp2_port_probe(), the calculation of port->first_rxq is adjusted
to cope with the different allocation strategy between PPv2.1 and
PPv2.2. Due to this change, the 'next_first_rxq' argument of this
function is no longer needed and is removed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts how the MVPP2_ISR_RXQ_GROUP_REG register is
configured, since it changed between PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The PPv2.2 unit is connected to an AXI bus on Armada 7K/8K, so this
commit adds the necessary initialization of the AXI bridge.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit handles a few miscellaneous differences between PPv2.1 and
PPv2.2 in different areas, where code done for PPv2.1 doesn't apply for
PPv2.2 or needs to be adjusted (getting the MAC address, disabling PHY
polling, etc.).
Changed by Stefan for U-Boot:
Since mvpp2_port_power_up() has multiple callers in U-Boot, the U-Boot
version of this patch does not remove this function but simply adds the
check for MVPP21 before the mvpp2_port_fc_adv_enable() call.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts the mvpp2 driver register mapping and access logic
to support PPv2.2, to handle a number of differences.
Due to how the registers are laid out in memory, the Device Tree binding
for the "reg" property is different:
- On PPv2.1, we had a first area for the common registers, and then one
area per port.
- On PPv2.2, we have a first area for the common registers, and a
second area for all the per-ports registers.
In addition, on PPv2.2, the area for the common registers is split into
so-called "address spaces" of 64 KB each. They allow to access the same
registers, but from different CPUs. Hence the introduction of cpu_base[]
in 'struct mvpp2', and the modification of the mvpp2_write() and
mvpp2_read() register accessors. For PPv2.1, the compatibility is
preserved by using an "address space" size of 0.
Changed by Stefan for U-Boot:
Since we don't support multiple CPUs in U-Boot, I've removed all the
code, macros and variables introduced in the Linux patch version for this.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In PPv2.2, the MVPP2_RXQ_DESC_ADDR_REG and MVPP2_TXQ_DESC_ADDR_REG
registers have a slightly different layout, because they need to contain
a 64-bit address for the RX and TX descriptor arrays. This commit
adjusts those functions accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit modifies the mvpp2_defaults_set() function to not do the
loopback and FIFO threshold initialization, which are not needed for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The MVPP2_RXQ_CONFIG_REG register has a slightly different layout
between PPv2.1 and PPv2.2, so this commit adapts the functions modifying
this register to accommodate for both the PPv2.1 and PPv2.2 cases.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts the allocation and freeing of BM pools to support
PPv2.2. This involves:
- Checking that the number of buffer pointers is a multiple of 16, as
required by the hardware.
- Adjusting the size of the DMA coherent area allocated for buffer
pointers. Indeed, PPv2.2 needs space for 2 pointers of 64-bits per
buffer, as opposed to 2 pointers of 32-bits per buffer in
PPv2.1. The size in bytes is now stored in a new field of the
mvpp2_bm_pool structure.
- On PPv2.2, getting the physical and virtual address of each buffer
requires reading the MVPP2_BM_ADDR_HIGH_ALLOC to get the high order
bits of those addresses. A new utility function
mvpp2_bm_bufs_get_addrs() is introduced to handle this.
- On PPv2.2, releasing a buffer requires writing the high order 32 bits
of the physical address to MVPP2_BM_PHY_VIRT_HIGH_RLS_REG. We no
longer need to write the virtual address to MVPP2_BM_VIRT_RLS_REG.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds the definition of the PPv2.2 HW descriptors, adjusts
the mvpp2_tx_desc and mvpp2_rx_desc structures accordingly, and adapts
the accessors to work on both PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since the format of the HW descriptors is different between PPv2.1 and
PPv2.2, this commit introduces an intermediate union, with for now
only the PPv2.1 descriptors. The bulk of the driver code only
manipulates opaque mvpp2_tx_desc and mvpp2_rx_desc pointers, and the
descriptors can only be accessed and modified through the accessor
functions. A follow-up commit will add the descriptor definitions for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In preparation to the introduction for the support of PPv2.2 in the
mvpp2 driver, this commit adds a hw_version field to the struct
mvpp2, and uses the .data field of the DT match table to fill it in.
Having the MVPP21 and MVPP22 definitions available will allow to start
adding the necessary conditional code to support PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The PPv2.2 IP has a different TX and RX descriptor layout compared to
PPv2.1. In order to prepare for the introduction of PPv2.2 support in
mvpp2, this commit adds accessors for the different fields of the TX
and RX descriptors, and changes the code to use them.
For now, the mvpp2_port argument passed to the accessors is not used,
but it will be used in follow-up to update the descriptor according to
the version of the IP being used.
Apart from the mechanical changes to use the newly introduced
accessors, a few other changes, needed to use the accessors, are made:
- The mvpp2_txq_inc_put() function now takes a mvpp2_port as first
argument, as it is needed to use the accessors.
- Similarly, the mvpp2_bm_cookie_build() gains a mvpp2_port first
argument, for the same reason.
- In mvpp2_rx_error(), instead of accessing the RX descriptor in each
case of the switch, we introduce a local variable to store the
packet size.
- Similarly, in mvpp2_buff_hdr_rx(), we introduce a local "cookie"
variable to store the RX descriptor cookie, rather than accessing
it from the descriptor each time.
- In mvpp2_tx_frag_process() and mvpp2_tx() instead of accessing the
packet size from the TX descriptor, we use the actual value
available in the function, which is used to set the TX descriptor
packet size a few lines before.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As indicated by Russell King, the mvpp2 driver currently uses a lot
"phys" or "phys_addr" to store what really is a DMA address. This commit
clarifies this by using "dma" or "dma_addr" where appropriate.
This is especially important as we are going to introduce more changes
where the distinction between physical address and DMA address will be
key.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some more U-Boot specific 64bit support changes, mostly changing u32
to unsigned long.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mvpp2 is going to be extended to support the Marvell Armada 7K/8K
platform, which is ARM64. As a preparation to this work, this commit
enables building the mvpp2 driver on ARM64, by:
- Adjusting the Kconfig dependency
- Fixing the types used in the driver so that they are 32/64-bits
compliant. We use dma_addr_t for DMA addresses, and unsigned long
for virtual addresses.
It is worth mentioning that after this commit, the driver is for now
still only used on 32-bits platforms, and will only work on 32-bits
platforms.
Changed by Stefan for U-Boot:
Removed the Kconfig change as it does not apply to U-Boot this way.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some of the MVPP2_PRS_RI_* definitions use the ~(value) syntax, which
doesn't compile nicely on 64-bit. Moreover, those definitions are in
fact unneeded, since they are always used in combination with a bit
mask that ensures only the appropriate bits are modified.
Therefore, such definitions should just be set to 0x0. In addition, as
suggested by Russell King, we change the _MASK definitions to also use
the BIT() macro so that it is clear they are related to the values
defined afterwards.
For example:
#define MVPP2_PRS_RI_L2_CAST_MASK 0x600
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
becomes
#define MVPP2_PRS_RI_L2_CAST_MASK (BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_UCAST 0x0
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
Because the values (MVPP2_PRS_RI_L2_UCAST, MVPP2_PRS_RI_L2_MCAST and
MVPP2_PRS_RI_L2_BCAST) are always applied with
MVPP2_PRS_RI_L2_CAST_MASK, and therefore there is no need for
MVPP2_PRS_RI_L2_UCAST to be defined as ~(BIT(9) | BIT(10)).
It fixes the following warnings when building the driver on a 64-bit
platform (which is not possible as of this commit, but will be enabled
in a follow-up commit):
drivers/net/ethernet/marvell/mvpp2.c: In function ‘mvpp2_prs_mac_promisc_set’:
drivers/net/ethernet/marvell/mvpp2.c:524:33: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
^
drivers/net/ethernet/marvell/mvpp2.c:1459:33: note: in expansion of macro ‘MVPP2_PRS_RI_L2_UCAST’
mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L2_UCAST,
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mvpp2_bm_bufs_add() currently creates a fake cookie by calling
mvpp2_bm_cookie_pool_set(), just to be able to call
mvpp2_pool_refill(). But all what mvpp2_pool_refill() does is extract
the pool ID from the cookie, and call mvpp2_bm_pool_put() with this ID.
Instead of doing this convoluted thing, just call mvpp2_bm_pool_put()
directly, since we have the BM pool ID.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the warnings:
CACHE: Misaligned operation at range ...
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).
For this purpose we introduce a new phy-driver, called "Fixed PHY".
Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.
Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).
During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Fixed cache misaligned issue in the net driver. The issue shows-up when
a call to flush_dcache_range is made with unaligned memory. The memory
must be aligned to ARCH_DMA_MINALIGN.
Signed-off-by: Suji Velupillai <suji.velupillai@broadcom.com>
Tested-by: Suji Velupillai <suji.velupillai@broadcom.com>
Reviewed-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Shamez Kurji <shamez.kurji@broadcom.com>
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Cover Letter:
This series resolves issues specific to the Broadcom SF2 driver:
- fix cache misaligned issue
- convert to Kconfig
END
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently the mac address is programmed directly in _sunxi_emac_eth_init
making it a one time inflexible operation. By moving it into a separate
function, we can now use this more flexibly.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
Since the reserved RAM is tracked by gd->arch.resv_ram, calculation
of MC memory blocks can be simplified. The MC RAM is guaranteed to be
aligned by the reservation process.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
When the zynq_gem driver initializes the phy it sets the supported
features that the phy can support and advertise. However instead of
masking the supported features such that it limits the available
features it sets the phy to have the exact supported features of the
zynq_gem. This is problematic as it will enable features that a phy does
not have or cannot advertise.
Specifically this appears as an issue when using a phy that is only
capable of 10/100, but the zynq_gem driver will override this and try to
enable and advertise 10/100/1000.
Reported-by: Arno Steffens <star@gmx.li>
Fixes: 80243528ef ("net: gem: Fix gem driver on 1Gbps LAN")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Tested-by: Arno Steffens <star@gmx.li>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
For the boards such as smartweb on which the clock driver isn't
supported, the ethernet fail to be found when booting up with
the below log.
---8<---
Net: No ethernet found.
--->8---
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move the zynq to clock framework and remove unused functions as well as
the CONFIG_ZYNQ_PS_CLK_FREQ configuration.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If available use the clock framework to set the tx clock rate of the
zynq ethernet controller.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The gem[0-1]_rclk_ctrl registers control the source of the rx clock,
control and data signals and configure via ps7_init function. Don't
overwrite the register with the default value.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
cpsw driver tries to get macid for am43xx SoCs using the compatible
ti,am4372. But not all variants of am43x uses this complatible like
epos evm uses ti,am438x. So use a generic compatible ti,am43 to get
macid for all am43 based platforms.
Tested-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.
BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Modifying content of dev->name leads to the device tree corruption
because it points to the node name located there.
Signed-off-by: Daniel Strnad <strnadda@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In Uboot for Meson GX the compatible string in meson-gxbb.dtsi so far is:
compatible = "amlogic,meson6-dwmac", "snps,dwmac";
On Linux in the same dt file it's
compatible = "amlogic,meson-gx-dwmac", "amlogic,meson-gxbb-dwmac", "snps,dwmac";
To avoid breaking ethernet with the next DT synch from Linux to U-Boot
(planned as prerequisite for adding Meson GX MMC driver to U-Boot) add
"amlogic,meson-gx-dwmac" to the compatibility list in the designware
driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for programmable MAC impedance configuration and
fix typo in DT impedance parameters names.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 79e86ccb37 "vitesse: remove duplicated
argument to ||" correctly removed a redundant check.
However, I believe that the original code was simply wrong, and should have
been checking against RGMII_ID.
To fix this and avoid similar problems in the future, use the
phy_interface_is_rgmii helper function.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This device also works with the 88E1518 code, so we just adjust
the UID mask accordingly.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mask for the 88E1510 meant that the 88E1518 code would never be
used.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is code that is specifically for RGMII_TXID interface, but this
will never get used because the code checks that the RGMII interface
is RGMII_ID to RGMII_RXID; RGMII_TXID is after this.
To fix this and avoid similar problems in the future, use the
phy_interface_is_rgmii helper function.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Remove the redundant #ifdef CONFIG_DM_ETH/#endif.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Due to introducing the at91 clock driver, add the clock support.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for Marvell 88E1680 Integrated Octal
10/100/1000 Mbps Energy Efficient Ethernet Transceiver.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Fixup port_mac_address property in MC DPC with values from the u-boot
environment. Since u-boot already reads the environment MAC addresses
when probing the PHYs, use these values.
The u-boot environment MAC addresses take precedence over any eventual
ones defined in the DPC, except for the case where they are randomly
assigned (no u-boot env value declared for port).
The patch assumes the "/board_info/ports/" node is present in the DPC.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[York S: Fix several indentations]
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for SMSC LAN8742 in phylib
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds glue code required for enabling the designware
mac on stm32f7 devices.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new driver for the GMAC ethernet interface present in Rockchip
RK3288 SOCs. This driver subclasses the generic design-ware driver to
add the glue needed specifically for Rockchip.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Export all functions so that drivers can use them, or not, as the need
arises.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With rockchip we need to make adjustments after the link speed is set but
before enabling received/transmit. In preparation for this, split these
two pieces into separate functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This function can fail, so return the error if there is one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To allow other DM drivers to subclass the designware driver various
functions and structures need to be exported. Export these.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch fixes incorrect pointer on offset device in device tree blob.
When using with the component "Ethernet 1G/2.5G BASE-X PCS/PMA or SGMII"
it does not understand what type is XAE_PHY_TYPE_1000BASE_X and trying
to change frequency.
Signed-off-by: Kamensky Ivan <kamensky.ivan@mail.ru>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enable and use the clock driver routine
defined in clock driver toset required
clock appropriately.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
I am not longer using my old email address
"ajay.bhargav@einfochips.com". For U-Boot development email address is
now updated to contact@8051projects.net
Signed-off-by: Ajay Bhargav <contact@8051projects.net>
axi_emac, emaclite and gem have the same issue with registering
multiple instances with mdio busses. mdio bus name has to be uniq but
drivers are setting up only one name for all.
Use mdio_register_seq() and pass dev->seq number to allow multiple
mdio instances registration.
Reported-by: Phani Kiran Kara <phanikiran.kara@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- Remove exctra space
- Add space
- Add tab space
- Fix single line comments quotes
- Fix 'CHECK: Avoid CamelCase'
- Fix 'CHECK: Alignment should match open parenthesis'
- Fix 'WARNING: line over 80 characters'
- Re-arrage header include files
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch add driver model support for fec_mxc driver.
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
fec_get_hwaddr never used eth_device argument, hence removed.
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
LS2080A SoC family has QBMAN ver 4.0 whereas newer
SoCs like LS2088A, LS1088A has QBMAN ver 4.1
QBMAN ver 4.0 and ver 4.1 supports dqrr size as 4 and 8 respectively.
Add support of
to check QBMAN version based on SoC SVR
update dqrr_size accordingly
update code to support larger dqrr_size
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The VSC8601 config tried to add an RGMII skew based on #defines that
no config defines. That's quite an ugly way to do it. Since the skew
is only needed on RGMII interfaces, check the interface mode at
runtime, and apply the settings accordingly.
Tested on custom board with AM3352 SOC and VSC801 PHY.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The settings for 2.5G SGMII are wrong, which the 2.5G case is missed in
set_if_mode(), and the serdes PCS configuration are wrong, this patch uses
the correct settings took from Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 525d187af ("net: phy: Optionally force master mode for RTL PHY")
added the define to force the PHY into master mode. Unfortunatly this is
an all or nothing switch. So it applies to either all PHY's or no PHY's.
The bug that define tried to solve was a buggy PLL in the RTL8211C only.
The Olimex OLinuXino Lime2 has gotten an upgrade where the PHY was
replaced with an RTL8211E. With this define however, both lime2 boards
are either forced to master mode or not. We could of course have a
binary for each board, but the following patch fixes this by adding a
'quirk' to the flags to the rtl8211b and rtl8211c only. It is now
possible to force master mode, but only have it apply to the rtl8211b
and rtl8211c.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
All internal defines in the realtek phy are with a small X,
except MIIM_RTL8211X_CTRL1000T_MASTER. Make this more consistent
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The BIT macro is the preferred method to set bits.
This patch adds the bit macro and converts bit invocations.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix the following error, the $ret variable handling must
be part of the loop, while due to the missing parenthesis
it was not.
drivers/net/phy/micrel.c: In function ‘ksz9021_of_config’:
drivers/net/phy/micrel.c:303:2: warning: this ‘for’ clause does not guard... [-Wmisleading-indentation]
for (i = 0; i < ARRAY_SIZE(ofcfg); i++)
^~~
drivers/net/phy/micrel.c:305:3: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘for’
if (ret)
^~
drivers/net/phy/micrel.c: In function ‘ksz9031_of_config’:
drivers/net/phy/micrel.c:411:2: warning: this ‘for’ clause does not guard... [-Wmisleading-indentation]
for (i = 0; i < ARRAY_SIZE(ofcfg); i++)
^~~
drivers/net/phy/micrel.c:413:3: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘for’
if (ret)
^~
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
axi_emac, emaclite and gem have the same issue with registering
multiple instances with mdio busses. mdio bus name has to be uniq but
drivers are setting up only one name for all.
Use mdio_register_seq() and pass dev->seq number to allow multiple
mdio instances registration.
Reported-by: Phani Kiran Kara <phanikiran.kara@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: u-boot
Series-cc: Phani Kiran Kara <phanikiran.kara@gmail.com>
The rtl8169_intr_mask variable isn't used anywhere in the code, so
just remove it to avoid a GCC 6.2 compiler warning.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Apparently the indentation is off here, for the IGB model just want to
bail out early.
Fix this to avoid both compiler warnings and puzzled readers.
Pointed out by GCC 6.2's -Wmisleading-indentation warning.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
It is confusing that mdio commands work and report phy id as
decimal value when mii is working with hex values.
For example:
ZynqMP> mdio list
gem:
21 - TI DP83867 <--> ethernet@ff0e0000
ZynqMP> mdio read ethernet@ff0e0000 0
Reading from bus gem
PHY at address 21:
0 - 0x1140
ZynqMP> mii dump 21 0
Incorrect PHY address. Range should be 0-31
...
ZynqMP> mii dump 15
0. (1140) -- PHY control register --
(8000:0000) 0.15 = 0 reset
U-Boot normally takes hex values that's why this patch is changing mdio
command to handle hex instead of changing mii command to handle decimal
values.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support to detect RGMII link interface from link-interface
device tree entry. Also rename the existing link type enums so
that it provides meaningful interface like SGMII.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reported-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To send a parametrized command to the PHY over MDIO, we should write
the data first, the trigger the execution by the command register
write. Fix the access pattern in our MDIO write routine.
Apparently this doesn't really matter with the Realtek PHY on the
Pine64, but other PHYs (which require more setup) will choke on
the wrong order.
[Andre: add commit message]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
P1017 is a single-core version of P1023. There is no P1017 target
configured. Drop related macros. P1017 SoC is still supported.
Signed-off-by: York Sun <york.sun@nxp.com>
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xmR3
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2016-11-17
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
On ls2080 we have a separate network fabric component which we need to
shut down before we enter Linux (or any other OS). Along with that also
comes configuration of the fabric using a description file.
Today we always stop and configure the fabric in the boot script and
(again) exit it on device tree generation. This works ok for the normal
booti case, but with bootefi the payload we're running may still want to
access the network.
So let's add a new fsl_mc command that defers configuration and stopping
the hardware to when we actually exit U-Boot, so that we can still use
the fabric from an EFI payload.
For existing boot scripts, nothing should change with this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
[agraf: Fix x86 build]
Correct the SGMII enable bit position to 27 instead
of 31.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Modify the nwcfg bit definitions to have 32-bit
by removing the extra nibble.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 5a49f17481 ("net: mii: Use spatch to update miiphy_register")
updated the mvgbe implementation of smi_reg_read/smi_reg_write. Prior to
that change mvgbe_phy_read and mvgbe_phy_write where used as wrappers to
satisfy the phylib APIs. Because these functions weren't updated in that
commit build errors where triggered when CONFIG_PHYLIB was enabled.
Fix these build errors by removing mvgbe_phy_read and mvgbe_phy_write
and using smi_reg_read/smi_reg_write directly.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Like [1], reset the FLP burst timing for the KSZ9031 to the 16ms
specified by the IEEE802.3 standard from the chip's default of 8ms.
For more details, see the "Auto-Negotiation Timing" section of the
KSZ9031RNX datasheet.
[1] https://patchwork.kernel.org/patch/6558371/
Signed-off-by: Ash Charles <ash.charles@savoirfairelinux.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This driver supports the Synopsys Designware Ethernet QoS (Quality of
Service) a/k/a eqos IP block, which is a different design than the HW
supported by the existing designware.c driver. The IP supports many
options for bus type, clocking/reset structure, and feature list. This
driver currently supports the specific configuration used in NVIDIA's
Tegra186 chip, but should be extensible to other combinations quite
easily, as explained in the source.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org> # V1
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Cover-Letter: Fixes several spelling errors for the words "resetting",
"extended", "occur", and "multiple".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit b02e4044ff ("libfdt: Bring in upstream stringlist
functions") broke codying style in some places especially
by inserting an extra whitespace before fdt_stringlist_count().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
These two files have patch merge markers in them, within comments or
strings. Remove then, so that a search for merge markers does not show up
matches in these files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The signature for this macro has changed. Bring in the upstream version and
adjust U-Boot's usages to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update to drivers/power/pmic/palmas.c:
Signed-off-by: Keerthy <j-keerthy@ti.com>
Change-Id: I6cc9021339bfe686f9df21d61a1095ca2b3776e8
These have now landed upstream. The naming is different and in one case the
function signature has changed. Update the code to match.
This applies the following upstream commits by
Thierry Reding <treding@nvidia.com> :
604e61e fdt: Add functions to retrieve strings
8702bd1 fdt: Add a function to get the index of a string
2218387 fdt: Add a function to count strings
Signed-off-by: Simon Glass <sjg@chromium.org>
The call to flush cache on the transmit buffer was misplaced (for very
short packets) and asked to flush less than a cacheline.
Move the flush cache call to after a short packet has been padded
to minimum length (so the padding is flushed too), and round the size
up to a cacheline.
Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On some boards these switches are wired directly into a SERDES
interface on another Ethernet MAC. Add the ability to specify
these kinds of boards using CONFIG_MV88E61XX_FIXED_PORTS which defines
a bit mask of these fixed ports.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Marvell Link Street mv88e60xx is a series of FastEthernet switch
chips, some of which also support Gigabit ports. It is similar to the
mv88e61xx series which support Gigabit on all ports.
The main difference is the number of ports. Which affects the
PORT_COUNT define and the size of the mask passed to
mv88e61xx_port_set_vlan().
Other than that it's just a matter of adding the appropriate chip
IDs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Cc: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
cpsw driver supports only selection of phy mode in control module
but control module has more setting like RGMII ID mode selection,
RMII clock source selection. So ported to cpsw-phy-sel driver
from kernel to u-boot.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In the current driver implementation, config() callback is common
for AR8035 and AR8031 phy. In config() callback, driver tries to
configure MMD Access Control Register and MMD Access Address Data
Register unconditionally for both phy versions which leads to
auto negotiation failure in AM335x EVMsk second port which uses
AR8031 Giga bit RGMII phy. Fixing this by adding separate config
for AR8031 phy.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This adds support for internal delay on RX and TX on RGMII interface for the
AR8035 phy.
This is basically the same Linux driver do. Tested on a Zynq Zturn board (for
which u-boot support in is my tree; first patch waiting ML approval)
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix various misspellings of:
* deprecated
* partition
* preceding,preceded
* preparation
* its versus it's
* export
* existing
* scenario
* redundant
* remaining
* value
* architecture
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
when using tftp on the smartweb board, it prints a lot of
CACHE: Misaligned operation at range [23b2e000, 23b2e100]
warnings ... fixed them.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds support for the Armada 3700 SoC to the Marvell mvneta
network driver.
Not like A380, in Armada3700, there are two layers of decode windows for GBE:
First layer is: GbE Address window that resides inside the GBE unit,
Second layer is: Fabric address window which is located in the NIC400
(South Fabric).
To simplify the address decode configuration for Armada3700, we bypass the
first layer of GBE decode window by setting the first window to 4GB.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mvneta driver is also used on the ARMv8 64bit Armada 3700 SoC. This
patch fixes the compilation warnings seen on this 64bit platform.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the warnings:
CACHE: Misaligned operation at range ...
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move this option to Kconfig and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
The pch_gbe driver previously casted pointers to & from unsigned 32 bit
integers in many locations. This breaks the driver on 64 bit systems,
producing streams of compiler warnings about mismatched pointer &
integer sizes and then failing to keep track of addresses correctly at
runtime.
Fix the driver for 64 bit systems by using unsigned longs in place of
the previously used 32 bit integers.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reading the PCI BAR & converting the result to a physical address is not
safe across all architectures. For example on MIPS the virtual:physical
mapping is not 1:1, so we cannot directly make use of the physical
address.
Use the more generic BAR-mapping function dm_pci_map_bar to discover the
MMIO base address, which should work across architectures.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
out_be32 and in_be32 are actually #defined to little endian
writel/readl in arch/microblaze.
Just use __raw_writel/readl instead. That is also what is used
in the Linux kernel driver for this IP block
Tested on MIPSfpga. Can tftp a kernel.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Virtual to physical mapping isn't necessarily 1:1 for all architectures
Using ioremap_nocache allows for the arch code to translate the
physical address to a virtual address.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The current code would always use the speed and mode set by
CONFIG_ENV_SPI_MAX_HZ and CONFIG_ENV_SPI_MODE. But if using
SPI driver model it should get the values from DT.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary options.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The spatch series converting legacy drivers from miiphy_register to
mdio_register changed the return convention of the davinci_emac internal
MDIO accessors, making the internal code relying on it misbehaving:
no mdiodev get registered and U-Boot crashes when using net cmds in the
context of the old legacy net API.
ATM davinci_emac_initialize and cpu_eth_init don't return a proper value
in that case but fixing them would not avoid the crash.
This change is just a follow-up to the spatch pass, the MDIO accessors
of the mdiodev introduced by the spatch pass retain their proper values.
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The QMan is not used in FMan IM mode, so no QMI enqueue or QMI
dequeue are performed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ATM when receiving a packet the whole buffer is invalidated, this change
optimizes this behaviour.
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the remaining warnings:
CACHE: Misaligned operation at range
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
ATM the rx and tx descriptors are handled as cached memory while they
lie in a dedicated RAM of the SoCs, which is an uncached area.
Removing the said dcache ops, while optimizing the logic and clarifying
the code, also gets rid of most of the check_cache_range() incurred
warnings:
CACHE: Misaligned operation at range
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If the functions passed to the registration function are not in the same
C file (extern) then spatch will not handle the dependent changes.
Make those changes manually.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
For the 4xx related files:
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Run scripts/coccinelle/net/mdio_register.cocci on the U-Boot code base.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Implement MDIO bus read/write functions, initialize the bus and scan for
the PHY when phylib is enabled. Limit PHY speeds to 10/100 Mbps.
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The ethoc device can be configured to have a private memory region
instead of having access to the main memory. In that case egress packets
must be copied into that memory for transmission and pointers to that
memory need to be passed to net_process_received_packet or returned from
the recv callback.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Addresses used in buffer descriptors and passed in platform data or
device tree are physical. Addresses used by CPU to access packet data
and registers are virtual. Don't mix these addresses and use virt_to_phys
for translation.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add .of_match table and .ofdata_to_platdata callback to allow for ethoc
device configuration from the device tree.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extract reusable parts from ethoc_init, ethoc_set_mac_address,
ethoc_send and ethoc_receive, move the rest under #ifdef CONFIG_DM_ETH.
Add U_BOOT_DRIVER, eth_ops structure and implement required methods.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Don't use physical base address of registers directly, ioremap it first.
Save pointer in private struct ethoc and use that struct in all internal
functions.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add Kconfig entry for the driver, remove #define CONFIG_ETHOC from the
only board configuration that uses it and put it into that board's
defconfig.
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When adding support for the driver model the SPI EEPROM feature had
been ignored. Fix the build with both CONFIG_DM_ETH and
CONFIG_E1000_SPI enabled.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use the right phy_connect() prototype for CONFIGF_DM_ETH.
Support to get the phy interface from dt and set GMAC_UR.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some code may want to read reg values from DT, but from nodes that aren't
associated with DM devices, so using dev_get_addr_index() isn't
appropriate. In this case, fdtdec_get_addr_size_*() are the functions to
use. However, "translation" (via the chain of ranges properties in parent
nodes) may still be desirable. Add a function parameter to request that,
and implement it. Update all call sites to default to the original
behaviour.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Squashed in build fix from Stephen:
Signed-off-by: Simon Glass <sjg@chromium.org>
cpsw tries to flush dcache which is not in the range of PKTALIGN.
Because of this the following warning comes while flushing:
CACHE: Misaligned operation at range [dffecec0, dffed016]
Fix it by flushing cache of size aligned to PKTALIGN.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Keystone net can have multiple ethernet slaves, currently only
slave 1 is supported by the driver. Register multiple slaves as
individual ethernets to network framework.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Each line should be terminated by semi-colon. It was not caught
earlier as there is a proper statement. Fix it by changing the
comma with semi-colon.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On DRA72 EVM, cpsw slaves may be muxed with other modules. This
selection is controlled by a pcf gpio line. Add support for cpsw driver
to acquire mode-gpios and select the appropriate slave using gpio APIs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
This fixes the following CACHE warnings when using sun8i_emac:
=> dhcp
BOOTP broadcast 1
BOOTP broadcast 2
CACHE: Misaligned operation at range [7bf594a8, 7bf59628]
BOOTP broadcast 3
CACHE: Misaligned operation at range [7bf59c90, 7bf59e10]
CACHE: Misaligned operation at range [7bf5a478, 7bf5a5f8]
DHCP client bound to address 10.42.43.80 (1009 ms)
Note this commit also changes the max rx size from 2024 to 2044,
matching what the kernel driver uses.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
In sun8i_emac_board_setup, the driver partially configures the syscon
register for H3 EPHY. However, the settings are incomplete, and
completely unusable. The correct settings are later set in
sun8i_emac_set_syscon, but the incorrect CLK_SEL setting persists.
It is incorrect to use CLK_SEL to select 25 MHz, as the SoC does not
have a 25 MHz clock the EPHY can use.
This patch removes the setting of the syscon register in board_setup,
and also moves set_syscon above mdio_init. While mdio_init does not
access the PHY, it is better to have the PHY parameters setup before
the MDIO bus is registered.
Fixes: a29710c525 ("net: Add EMAC driver for H3/A83T/A64 SoCs.")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sun8i_emac driver erroneously configures the AHB2 clock when it
assumes it is configuring the AXI gates, which is not even documented
or ever appeared in either the WiP kernel driver or Allwinner's original
driver.
As a result, AHB2 clock mux is set to an invalid setting, making the
EPHY unusable.
Fixes: a29710c525 ("net: Add EMAC driver for H3/A83T/A64 SoCs.")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Fman module on LS1046A is similiar with that on LS1043A but
LS1046A has one more XFI (10GbE) interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch add EMAC driver support for H3/A83T/A64 SoCs.
Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY).
BIG Thanks to Andre for providing some of the DT code.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
If MAC is directly connected to another MAC (like a switch for example)
we don't need to probe for a phy, autoneogation and so on. We simply
have to setup speed.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Return value of rtl_send_common propogates unmodified all the way
up to eth_send and further to API consumer if CONFIG_API is enabled.
Previously rtl_send_common returned number of bytes sent on success
which was erroneouly detected as error condition by API consumers
that checked for operation success by comparing return value with 0.
Switch rtl_send_common to use common convention: return 0 on success
and negative value for failure.
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for aquantia AQR106/107 PHY.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 90b7fc924a "net: designware: support phy reset device-tree
bindings" made DW GMAC driver dependent on DM_GPIO by unconditional
usage of purely DM_GPIO stuff like:
* dm_gpio_XXX()
* gpio_request_by_name()
But since that driver as of today might be easily used without
DM_GPIO (that's the case for Synopsys AXS10x boards) we're
shielding all DM_GPIO things by ifdefs.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit a058052c "net: phy: do not read configuration register on reset",
changes the behaviour of the phy_reset function such that the state of
the BMCR register is not preserved during reset.
Change the config function for the m88e1310 so that it does not do a
reset after configuring auto-negotiation.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds a phy driver for the Micrel KSZ886x switches.
Similarly to the KSZ8895, SoC MAC is directly connected to the switch
MAC on the switch CPU port, so the link to the switch is always up.
KSZ886x switches can be used in the following configuration modes:
- Unmanaged mode with config stored in external EEPROM
- Managed mode over SPI
- Managed mode over I2C
- Managed mode over mdio/mdc (aka MIIM or SMI)
This patch supports only unmanaged and MIIM modes.
Based on Micrel KSZ886x driver from Linux kernel and
Micrel KSZ8895 driver from U-Boot.
Verified with the KSZ8863MLL.
Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The rtl8169 driver uses a global variable to store the register address
of the adapter being operated upon. This is updated to point at the
correct adapter when sending or receiving a packet, or shutting down the
adapter, but not when initializing the adapter. Consequently, switching
between different adapters within the same U-Boot runtime does not work
correctly since the driver programs the wrong registers during
rtl8169_eth_start() -> rtl8169_common_start() -> rtl8169_hw_start().
Note that since rtl8169_eth_stop() does set the global variable, the
second consecutive attempt to use the "new" adapter did work even before
this patch, because each time network usage is shut down, the network
core calls stop, which sets the variable so that the next start does
actually initialize the hardware, and the adapter works.
Equally, rtl8169_eth_probe() calls rtl_init() which sets the global, so
if using only a single device, or if picking the "right" device (based on
probe order) when multiple devices are present, ioaddr will already be set
correctly from the get-go, so the issue does not occur.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add driver-model support to this driver. The old code remains for now so
that we can convert boards one at a time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The end address of the cache flush must be cache-line-aligned since
otherwise (at least on ARM926-EJS) the request is ignored. When the cache
is enabled this means that packets are not sent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Adjust this driver to avoid using struct netdev in functions that driver
model will call. Also refactor the receive function to be compatible with
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
Add ethernet driver for the AR933x and AR934x Atheros MIPS machines.
The driver could be easily extended to other WiSoCs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wills Wang <wills.wang@live.com>
[fixed Kconfig dependency]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
If dev->iobase is 64 bits wide then writing the value of the BAR into a
pointer to iobase will not work on big endian systems, where the BAR
value will incorrectly get written to the upper 32 bits of the 64 bit
variable. Fix this by reading the BAR into a u32, matching the type
expected by pci_read_config_dword.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fix the pcnet driver to build safely on 64 bit platforms, in preparation
for allowing MIPS64 builds for Malta boards.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that MIPS virt_to_phys can handle kseg1 addresses on MIPS32, stop
manually converting addresses to their kseg0 equivalents in the pcnet
driver.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
All members of the DMA descriptor must be 32-bit, even on 64-bit
architectures: change the type to u32 to ensure this. Also, fix
other warnings.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Use phys_addr_t not unsigned long long to test that we're within
DMA'able memory]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for the snps,reset-gpio, snps,reset-active-low (optional) and
snps,reset-delays-us device-tree bindings. The combination of these
three define how the PHY should be reset to ensure it's in a sane state.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using rcw protocols to support 10G on MAC9 and MAC10, these MACs
should not be identified as 1G interface, otherwise, one MAC will be
listed as two Ethernet ports. For example, MAC9 will be listed as
FM1@TGEC1 and FM1@DTSEC9.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The code assumed that if the interface is not RGMII configured
then it must be SGMII configured. This device has the ability
to support most of the MII interfaces. Therefore add the
helper for SGMII and only configure the device if the interface is
configured for SGMII.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move the phy_interface_is_rgmii to the phy.h
file for all phy's to be able to use the API.
This now aligns with the Linux kernel based on
commit e463d88c36d42211aa72ed76d32fb8bf37820ef1
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Not all devices use the same internal delay or fifo depth.
Add the ability to set the internal delay for rx or tx and the
fifo depth via the devicetree. If the value is not set in the
devicetree then set the delay to the default.
If devicetree is not used then use the default defines within the
driver.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the ability to pass the phy-handle node offset
to the phy driver. This allows the phy driver
to access the DT subnode's data and parse accordingly.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the ability to read the phy-handle node of the
cpsw slave. Upon reading this handle the phy-id
can be stored based on the reg node in the DT.
The phy-handle also needs to be stored and passed
to the phy to access any phy data that is available.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Different TI platforms has to read with different combination to
get the mac address from efuse. So add support to read mac address
based on machine/device compatibles.
The code is taken from Linux drivers/net/ethernet/ti/cpsw-common.c
done by Tony Lindgren.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since dra7x platforms address bus is define as 64 bits to support
LAPE, fdtdec_get_addr() returns a invalid address for mdio based
and gmii_sel register address. Fixing this by using
fdtdec_get_addr_size_auto_noparent() which will derive address
cell and size cell from its parent.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On some boards number of slaves can be 1 when only one port
ethernet is pinned out. So do not break when slave_index and
num slaves check fails, instead continue to parse the next
child.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The previous mv88e61xx driver was a driver for configuring the
switch, but did not integrate with the PHY/networking system, so
it could not be used as a PHY by U-boot. This is a complete
rework to support this device as a PHY.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
No boards are using this driver. Remove in preparation for a new
driver with integrated PHY support.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Use simpler runtime cpu dection macros.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The patch
"net: phy: do not read configuration register on reset"
(sha1: a058052c35)
was causing regression on zynq zc702 board where Marwell 88e1118
phy was resetted after negotiation was setup.
Phy reset is done pretty early in phy_connect_dev() and doens't need to
be called again in phy code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Propagate error code from genphy_update_link() to phy startup().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Memset pools_params as "0" to avoid garbage value in dpni_set_pools.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some SerDes protocols might not enable all l2switch ports. In this case,
these ports should not be configured to perform Rx/Tx operations.
This also fixes an issue when flooded frames were also switched to
disabled ports and frames start to accumulate, consuming memory
and eventually causing head-of-line blocking for other frames.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PCS auto negotaiation bit should be enabled
along with SGMII autonegotation enabled
in phy.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support of SGMII to TI phy dp838367
Enable the SGMII and PCS settings in phy
control, CFG2 and BIST registers
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Return error from probe in case of invalid phy address.
This fixes the issue of uboot crash if phy is not detected.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Provide board specific option how to read MAC address from ROM.
Do it in generic way to be reusable by differnet boards.
If this is not enough board specific functions can be created.
Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In SGMII cases the isolate bit might set after DMA and
ethernet resets and hence check and clear during
setup_phy if it was set.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pass appropriate interface type to phy_connect
instead of zero.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support of SGMII interface for zynq GEM.
Read xlnx,emio property from DT.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the mvpp2 ethernet controller which is integrated
in the Marvell Armada 375 SoC. This port is based on the Linux driver (v4.4),
which has been stripped of the in U-Boot unused portions.
Tested on the Marvell Armada 375 eval board db-88f6720.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
The RTL8211B_driver structure in drivers/net/phy/realtek.c contains a
wrong PHY ID (0x1cc910 instead of 0x1cc912) in the uid field.
The lowest four bits of the PHY ID encode the chip revision (B+C/D/E/F)
of the RTL8211 and the code originally applied a mask of 0xfffff0 to
the PHY ID, so that matching the PHY ID to the appropriate driver code
was only done on the chip type (RTL8211), but not on a specific
revision.
After introduction of support for the RTL8211E, which needed another
startup function than the older chip revisions, commit
4220504767 changed the mask to 0xffffff
to make the chip revision relevant for the match, but didn't provide
the now-relevant lower bits of the uid field for the RTL8211B/C.
Fix this by setting the full PHY ID in the RTL8211B_driver uid field.
Fixes: 4220504767 ("net/phy: realtek: Fix the PHY ID mask to ensure the correct Realtek PHY is detected")
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch introduces CONFIG_RTL8211X_PHY_FORCE_MASTER. If this
define is set, RTL8211x PHYs (except for the RTL8211F) will have their
1000BASE-T master/slave autonegotiation disabled and forced to master
mode.
This is helpful for PHYs like the RTL8211C which produce unstable links
in slave mode. Such problems have been found on the A20-Olimex-SOM-EVB
and A20-OLinuXino-Lime2.
There is no proper way to identify affected PHYs in software as the
RTL8211C shares its UID with the RTL8211B. Thus, this fix requires
the introduction of an #ifdef.
CC: fradav@gmail.com
CC: merker@debian.org
CC: hdegoede@redhat.com
CC: ijc@hellion.org.uk
CC: joe.hershberger@ni.com
Signed-off-by: Michael Haas <haas@computerlinguist.org>
Tested-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
NULL pointer should be checked before any dereference. This patch
move memest after the NULL pointer check.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Free dflt_dpio pointer after its usage during error handling
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When DEBUG_RTL8169 is on, a build error occurs in function
'rtl_init': error: 'dev' undeclared. Fix this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Stephen Warren <swaren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Fixup MPC8641HPCN* and r2dplus configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
Return value of get_mc_boot_status() in case of failure is not necessary
to be -1.
So update the error condition check.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Yao Yuan <yao.yuan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch integrate DPAA2 ethernet driver existing PHY framework.
Call phy_connect and phy_config as per available DPMAC id defined
in SerDes Protcol.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
In commit <a058052c358c> [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Bit 12(AUTO_NEGOTIATION)
is cleared too. It causes auto-negotiation timeout error on Atheros's
PHY AR8033.
To fix this problem, genphy_config_aneg() and genphy_restart_aneg()
needs to be called in ar8035_config() to enable and restart
auto-negotiation.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use fdt32_to_cpu() to convert the data correctly for both endianness
platforms.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Not only powerpc/mpc85xx but also Freescale Layerscape platforms will
use fdt_fixup_fman_firmware() to insert Fman ucode blob into the device
tree. So move the function to Fman driver code.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the QE firmware struct is shared with Fman, move the header file
out of drivers/qe/.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The problem with current implementation is that SPDDONE bit is 1
but link bit is zero. That's why phydev->link is setup to 0
which ending up in driver failure that link is not up.
Log:
Zynq> dhcp
ethernet@e000b000 Waiting for PHY auto negotiation to complete.......
done
ethernet@e000b000: No link.
There is at least 1ms delay between spddone bit and link up.
Use genphy_read_status() instead of realtek implemenation which is
working with page 11. Linux driver is also using generic implementation.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Due to introducing the new peripheral clock handle functions,
use these functions to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
[fixup for missing clk.h in at91_emac.c]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
With commit a058052c [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Resulting in bit 12
being cleared (A/N enable). This leads to autonegotiation link problems,
at least on the Marvell Armada ClearFog board. I suspect that other
boards using this driver will be affected as well.
At the of m88e1111s_config(), phy_reset() is called. This is not needed
for the PHY to load the changed configuration, as phy_reset() is called
a few lines before already. So lets call genphy_restart_aneg() here
instead to start the AN correctly.
Tested on clearfog.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Instead of coding the soft PHY reset function multiple times in marvell.c,
lets call the common phy_reset() function from phy.c.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When Micrel phy is selected without CONFIG_PHY_MICREL_KSZ9031 or
CONFIG_PHY_MICREL_KSZ9021 there is a build error. Fixing this
by adding proper ifdefs
drivers/net/phy/micrel.c:370:39: error: array type has incomplete element type
static const struct ksz90x1_reg_field ksz9031_ctl_grp[] =
^
drivers/net/phy/micrel.c:372:39: error: array type has incomplete element type
static const struct ksz90x1_reg_field ksz9031_clk_grp[] =
^
drivers/net/phy/micrel.c: In function ‘ksz9031_of_config’:
drivers/net/phy/micrel.c:377:23: error: array type has incomplete element type
struct ksz90x1_ofcfg ofcfg[] = {
^
drivers/net/phy/micrel.c:379:13: error: ‘ksz90x1_rxd_grp’ undeclared (first use in this function)
{ MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, 2, ksz90x1_rxd_grp, 4 },
^
drivers/net/phy/micrel.c:379:13: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/phy/micrel.c:380:13: error: ‘ksz90x1_txd_grp’ undeclared (first use in this function)
{ MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, 2, ksz90x1_txd_grp, 4 },
^
drivers/net/phy/micrel.c:386:3: warning: implicit declaration of function ‘ksz90x1_of_config_group’ [-Wimplicit-function-declaration]
ret = ksz90x1_of_config_group(phydev, &(ofcfg[i]));
^
drivers/net/phy/micrel.c:377:23: warning: unused variable ‘ofcfg’ [-Wunused-variable]
struct ksz90x1_ofcfg ofcfg[] = {
^
drivers/net/phy/micrel.c: At top level:
drivers/net/phy/micrel.c:370:39: warning: ‘ksz9031_ctl_grp’ defined but not used [-Wunused-variable]
static const struct ksz90x1_reg_field ksz9031_ctl_grp[] =
^
drivers/net/phy/micrel.c:372:39: warning: ‘ksz9031_clk_grp’ defined but not used [-Wunused-variable]
static const struct ksz90x1_reg_field ksz9031_clk_grp[] =
^
scripts/Makefile.build:277: recipe for target 'drivers/net/phy/micrel.o' failed
make[1]: *** [drivers/net/phy/micrel.o] Error 1
Makefile:1201: recipe for target 'drivers/net/phy' failed
make: *** [drivers/net/phy] Error 2
make: *** Waiting for unfinished jobs....
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
NULL check is made after the pointer dereference. This patch
fixes this issue.
Signed-off-by: Vishwas Srivastava <vishu.kernel@gmail.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
emac module of the davinci platform supports only 8 tx and 8
rx channels (total 16). emac driver for davinci platform,
however, while doing initialization of the dma descriptor
head pointers, wrongly initializes the 16 head pointers
(instead of 8) for tx dma and 16 head pointers (insted of 8)
for rx dma, which is wrong. The result is, that this register
initilization spills over the other registers which was not
intended and is undesirable. This patch fixes this problem.
Signed-off-by: Vishwas Srivastava <vishu.kernel@gmail.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This driver implements MAC and MII layer of the ethernet controller.
Network data transfer is handled by controller internal DMA engine.
Ethernet controller is configurable through device-tree file.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Update printf with dpbp_exit to match with previous function call.
Signed-off-by: Itai Katz <itai.katz@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
All fields of struct dprc_cfg are not being configured while creating
child container. "Not" configured fields are assumed to be 0.
So memset dprc_cfg before configuring the fields.
Signed-off-by: Itai Katz <itai.katz@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Cortina phy cannot support soft reset, this commit implements probe
for Cortina PHY to tell phylib to skip phy soft reset by setting
PHY_FLAG_BROKEN_RESET in flags.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current driver always performs a phy soft reset when connecting the phy
device, but soft reset is not always supported by a phy device, so
introduce a quirk PHY_FLAG_BROKEN_RESET to let such a phy device to skip
soft reset. This commit uses 'flags' of phy device structure to store the
quirk.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The picoseconds to register value divisor(ps_to_regval) should be 60 and not
200. Linux has KSZ9031_PS_TO_REG defined to be 60 as well. 60 is the correct
divisor because the 4-bit skew values are defined from 0x0000(-420ps) to
0xffff(480ps), increments of 60.
For example, a DTS skew value of 420, represents 0ps delay, which should be 0x7.
With the previous divisor of 200, it would result in 0x2, which represents a
-300ps delay.
With this patch, ethernet on the SoCFPGA DE0 Atlas is now able to work with
1Gb ethernet.
References:
http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf -> page 26
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use the 'autoneg' flag available in phydev when checking if
autoneg is in use.
The previous implementation was checking directly in the PHY
if autoneg was supported. Some PHYs will report that autoneg
is supported, even when it is disabled. Thus it is not possible
to use that bit to determine if autoneg is currently in use or
not.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When configuring a PHY in fixed (forced) link mode, in order for
the changes to be applied, either one of these conditions must
be triggered:
1- PHY is reset
2- Autoneg is restarted
3- PHY transitions from power-down to power-up
Neither of these is currently done, so effectively the fixed link
configuration is not applied in the PHY.
Fix this by setting the Autoneg restart bit.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Micrel PHYs KSZ8021/31 and KSZ8081 have a feature where MDIO address 0
is considered as a broadcast address; the PHY will respond even if it
is not its configured (pinstrapped) address. This feature is enabled
by default.
The Linux kernel disables that feature at initialisation, but not
before it probes the MDIO bus. This causes an issue, because a PHY
at address 3 will be discovered at addresses 0 and 3, but will then
only respond at address 3. Because Linux attaches the first PHY it
discovers on 'eth0', it will attach the PHY from address 0, which
will never answer again.
Fix the issue by disabling the broadcast feature in U-Boot, before
Linux is started.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This property allows to specify fastest connection mode supported by
the MAC (as opposed to features of the phy).
There are situations when phy may handle faster modes than the
MAC (or even it's particular implementation or even due to CPU being too
slow).
This property is a standard one in Linux kernel these days and some
boards do already use it in their device tree descriptions.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
cc: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current implementation only sets "port select" bit for non-1Gb mode.
That works fine if GMAC has just exited reset state but we may as well
change connection mode in runtime. Then we'll need to reprogram GMAC for
that new mode of operation and if previous mode was 10 or 100 Mb and new
one is 1 Gb we'll need to reset port mode bit.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
cc: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This new function will allow MAC drivers to override supported
capabilities of the phy. It is required when MAC cannot handle all
speeds supported by phy.
For example phy supports up-to 1Gb connections while MAC may only work
in modes up to 100 or even 10 Mbit/sec.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. This does not work with
the genphy driver though because the genphys config_init function
will overwrite all values adjusted by of_set_phy_supported. Fix
this by initialising the genphy features in the phy_driver struct
and in config_init just limit the features to the ones the hardware
can actually support. The resulting features are a subset of the
devicetree specified features and the hardware features.
This is a copy of the patch from Linux kernel, see
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=c242a47238fa2a6a54af8a16e62b54e6e031d4bc
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When a Gigabit PHY device is connected to a 10/100Mbits capable Ethernet
MAC, the driver will restrict the phydev->supported modes to mask off
Gigabit. If the Gigabit PHY comes out of reset with the Gigabit features
set by default in MII_CTRL1000, it will keep advertising these feature,
so by the time we call genphy_config_advert(), the condition on
phydev->supported having the Gigabit features on is false, and we do not
update MII_CTRL1000 with updated values, and we keep advertising Gigabit
features, eventually configuring the PHY for Gigabit whilst the Ethernet
MAC does not support that.
This patches fixes the problem by ensuring that the Gigabit feature bits
are always cleared in MII_CTRL1000, if the PHY happens to be a Gigabit
PHY, and then, if Gigabit features are supported, setting those and
updating MII_CTRL1000 accordingly.
This is a copy of patch from Linux kernel, see
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=5273e3a5ca94fbeb8e07d31203069220d5e682aa
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new member 'tbiaddr' to tsec_private struct. For non-DM driver,
it is initialized as CONFIG_SYS_TBIPA_VALUE, but for DM driver, we
can get this from device tree. Update the bindings doc as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This adds driver model support to Freescale TSEC ethernet driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For internal routines like redundant_init(), startup_tsec() and
init_phy(), change to use tsec_private pointer as the parameter.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adjust static functions in a proper order so that forward declaration
of tsec_send() can be avoided.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
rxbd and txbd are declared static with 8 byte alignment requirement,
but they can be put into struct tsec_private as well and are natually
aligned to 8 byte.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present rx_idx and tx_idx are declared as static variables
in the driver codes. To support multiple interfaces, move it to
struct tsec_private.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Clean up the tsec and fsl_mdio driver codes a little bit, by:
- Fix misuse of tab and space here and there
- Use correct multi-line comment format
- Replace license identifier to GPL-2.0+
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
You can now configure LAG on VSC9953's ports using the command:
ethsw [port <port_no>] aggr {[help] | show | <lag_group_no>}
A port must belong to a single LAG. By default, a port
belongs to a LAG equal to the port's number.
For each frame, a hash will be calculated based on
Source/Destination MAC addresses, Source/Destination IP(v4/v6)
addresses, Source/Destination ports. This hash will be used to
select a single egress port from LAG. This also assures
that frames from the same flow will always have the
same egress port.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
By default, the aging period is set to 0, so the dynamic
FDB entries are never removed. This patch sets the aging
time to 300 seconds.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When doing a software reset, the reset flag should be written without
other bits set. Writing the current state will lead to restoring the
state of the PHY (e.g. Powerdown), which is not what is expected from
a software reset.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Michael Welling <mwelling@ieee.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Management Complex firmware 9.0 has fixed the issue of
dprc_destroy_container i.e. the used portal is not return to the
free pool. Which was resulting in error ethernet driver want to
use this portal via either DPL or dynamically in Linux.
Hard-coding of portal id is removed.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add debug information prints to provide DPMAC statistics
- Number of bytes received
- Number of received and discard frames
- Number of bytes transferred
- Number of frames transferred
etc.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Management Complex FW 9.0 set the hardware depletion to be 20
buffers in order to support multiple pools in DPNI. This requires
driver to fill the pool with at least 21 to be able to receive
frames. So, Increase number of buffers for a pool.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Management Complex FW 9.0 puts a new requirement to provide Tx
confirmation and error queue configuration by calling
dpni_set_tx_conf API.
Configure report of only error frames for a tx frame.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Management Complex FW 9.0 puts a new requirement to prepare extended
parameters which should be provided as input in dpni_create. extended
parameters includes traffic class and IP reassembly configurations.
So prepare extended parameters with default "0" as input for
dpni_create.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MC firmware version 9.0.0 contains
- Support of new APIs
- Update in existing APIs
- Change in Major and minor version of DPAA2 objects
This patch contains modifications in FLIB files to support new
MC firmware version.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Check and compare version of management complex's object with
the version supported by Freescale ldpaa2 ethernet driver.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Size of this snprintf "lltemac.%lx" is bigger than 16 characters.
Replacing it with "ll_tem.%lx"
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
MDC setting depends on pclk input clocks which varies across SoC. This
driver is used by xilinx zynq and zynqmp SOC.
Input clock frequence on silicon is 125MHz where divider 64 put
frequency below 2.5MHz requires by spec (125/64=1.95).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable automatic crossover cable detection.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add PHYLIB and MII dependencies and enable it by default for Microblaze.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When IP is configured with pong buffers, IP is receiving packets to ping
and then to pong buffer and than ping again.
The original logic in the driver remains there that when ping buffer is
free, pong buffer is checked too and return if both are free.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The original logic in the driver was exchanging buffers which are used for
sending packet and tx_ping and tx_pong buffers were exchanged all the
time to ensure that IP has enough time to send the packet out.
Based on this "feature" send function was using nextbuffertouse variable
to save which buffer should be used.
Before this algorithm was called driver checked that there is free
buffer available.
This checking remains in the driver but driver tries to use tx_ping
first if available. If not, tx_pong buffer is used instead.
To reach this code the original condition is met that at least one of the
buffer should be available.
Testing doesn't show any performance drop when this patch is applied.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This flag is not documented anywhere in the latest documentation that's
why this patch removes it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simplify logic how to find out if there is free TX buffer.
Both buffers are checked all the time that's why logic around order
can be removed.
Also add check when only one buffer is available.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move to use indirect register access when timeout expires for resetting
TX buffers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Do initialization via indirect register access.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use u-boot coding style how to setup and access MDIO bus.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Also add dependency on PHYLIB and MII which is required.
Clean PHYLIB dependency from the driver too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Rename few functions to fit to the new name convention used by DM.
Suggested-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Saving iobase directly to private structure helps with moving to DM.
There is an option to load iobase from pdata but it is additional load.
Pointer to private structure is available all the time.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simplify mdio_wait function by passing regs directly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix these compilation warning by proper grouping:
In function 'axi_dma_init': drivers/net/xilinx_axi_emac.c:391:7:
warning: suggest parentheses around operand of '!' or change '&' to '&&'
or '!' to '~' [-Wparentheses]
if (!(in_be32(&priv->dmatx->control) |
^
In function 'axiemac_send': drivers/net/xilinx_axi_emac.c:501:21:
warning: suggest parentheses around operand of '!' or change '&' to '&&'
or '!' to '~' [-Wparentheses]
while (timeout && (!in_be32(&priv->dmatx->status) &
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
During the initialization of PHY the gigabit bit capable is set if the
controller is a GEM. However, for sama5d2 and sama5d4, the GEM is
configured to support only 10/100.
Improperly setting the GBE capability leads to an unresponsive MAC
controller. This patch fixes this behavior allowing using the gmac with
these SoCs.
Suggested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fixed minor checkpatch warning]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Current code compares the return pointer of function
qbman_cena_write_start with NULL. Instead the value of the return
pointer should be compared.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When building katmai, it reports quite a lot
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Fix this by casting the dev->iobase with u_long.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
BUILD_BUG_* macros have been defined in several headers. It would
be nice to collect them in include/linux/bug.h like Linux.
This commit is cherry-picking useful macros from include/linux/bug.h
of Linux 4.4.
I did not import BUILD_BUG_ON_MSG() because it would not work if it
is used with include/common.h in U-Boot. I'd like to postpone it
until the root cause (the "error()" macro in include/common.h causes
the name conflict with "__attribute__((error()))") is fixed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
pci_virt_to_mem() uses virt_to_phys() to get the physical address.
But pci_virt_to_mem() is also called with uncached addresses which
is wrong according to the documentation of virt_to_phys().
Refactor the PCI_TO_MEM() macro to optionally map an uncached address
back to a cached one before calling pci_virt_to_mem().
Currently pcnet works because virt_to_phys() is incorrectly implemented
on MIPS. With the upcoming asm header file update for MIPS, the
virt_to_phys() implementation will be fixed. Thus this patch is needed
to keep pcnet working on MIPS Malta board.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.
With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:
PHY-mode ("phy-mode") and PHY-address ("reg").
The base addresses for the ethernet controllers can be removed from
the header files as well.
Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
The change fixes PHY write operation, which incorrectly waits for
released busy state before issuing a write operation, this breaks
sequential write/read operation logic, because read operation
starts immediately on request and it completes, when busy state is
gone.
Instead of adding the second preceding busy state check to read
function, do busy state release check after issuing a write operation,
this method of operation is also recommended by the LPC32xx User's
Manual, see MII Mgmt Indicators Register notes:
For PHY Write if scan is not used:
1. Write 0 to MCMD
2. Write PHY address and register address to MADR
3. Write data to MWTD
4. Wait for busy bit to be cleared in MIND
Reported-by: Alexandre Messier <amessier@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Alexandre Messier <amessier@tycoint.com>
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update this driver to use the proper driver-model PCI API functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Most driver model PCI functions have a dm_ prefix. At some point, when the
old code is converted to driver model and the old functions are removed, we
will drop that prefix.
For consistency, we should use the dm_ prefix for all driver model
functions. Update pci_get_bdf() accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Introduced in 45b4773 (net/arp: account for ARP delay, avoid duplicate packets on timeout)
Check the arp timeout and adjust the timeout start time before the call
to eth_recv() so that the sandbox driver has the opportunity to adjust
the sandbox timer after the new start time has been recorded.
Also, change the adjustment amount by 11 seconds instead of exactly the
10 seconds that the ping timout is expecting since the timeout check is
looking for the time elapsed to be greater than but not equal to the
specified delay.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Simon Glass <sjg@chromium.org>
Commit 08ad9b068a (" ar8031: modify the config func of ar8031 to
ar8021_config") selected 'ar8021_config' as the configuration function
for AR8031.
The correct would be to use 'ar8035_config' instead as AR8031/AR8035
have the same programming model and even share the same phy driver
in the linux kernel: drivers/net/phy/at803x.c.
Tested on a mx6qsabresd and wandboard, which now can work without
any PHY setup code in the board files.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In struct e1000_rx_desc, field 'length' is declared as
uint16_t, so use le16_to_cpu() to do endianness conversion.
Also drop conversion on 'status' which is declared as
uint8_t.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If fecmxc_initialize_multi() fails, it frees but does not unregister
the mdio bus, causing subsequent uses of the "mii" command to crash.
Fix this by adding mdio_unregister() calls where needed.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
If the host clock frequency is higher than 100 MHz, the MDIO hold
time needs to be increased from its current setting of one cycle in
order to meet the specified minium of 10 ns. Writing an appropriate
value to the HOLDTIME field of the MII_SPEED register achieves this.
Comment copied from Linux kernel.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Trailing backslashes are necessary only in macros, not in the actual
code, so remove them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB
from legacy board header files.
This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE
are selected.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reported-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Per the comments, e1000_spi_eeprom_disable_wr() and
e1000_spi_eeprom_write_status() have been tested.
Remove the #if 0, #endif and mark them as __maybe_unused.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
CONFIG_MVBC_1G is not referenced anywhere, hence remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add code to process the KSZ9021/KSZ9031 OF props if they are present
and configure skew registers based on the information from the OF.
This code is only enabled if the DM support for ethernet is also
enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
V2: - Implement struct ksz90x1_reg_field to describe the skew register
fields more accurately.
- Fix RXDV/TXEN skew register default value and offset.
Use core to call net_process_received_packet() instead of call inside
the driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
recv function should return 0 instead of frame_len not to
proceed the same packet again in core.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We don't disable unused FM1-DTSEC1 MAC node in FMAN v2 since it is
used by MDIO. For FMAN v3, MDIO uses dedicated controller, so we
can disable unused FM1-DTSEC1 MAC node to avoid being probed in
Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: revised commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
Remove verbose message for FMan port.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
[York Sun: Added commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
The MC version numbers provide no meaningful information
about binary interface compatibility, so remove the
check which refuses to start the MC unless a specific
version is found.
Version checking is supposed to be done at the individual
object level, and individual drivers are responsible
for their own version checking.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
With gcc-5.x we get a warning about the ambiguity of BUG_ON(!a != b) and
becomes BUG_ON((!a) != b). In this case reading of the function leads to
us wanting to rewrite this as BUG_ON(a != b).
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Cc: Haiying Wang <Haiying.Wang@freescale.com>
Cc: Roy Pledge <Roy.Pledge@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Do not set interface via configs. Read information from DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
- Enable DM_ETH by default for Zynq and ZynqMP
- Remove board_eth_init code
- Change miiphy_read function to return value instead of error code
based on DM requirement
- Do not enable EMIO DT support by default
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function was used for OF init before DM.
Remove this function as the part of move to DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Enable access to MDIO before zynq_gem_init is called.
It enables read information about phy earlier.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move phy init code out of zynq_gem_init. DM drivers are normally calling
this code from probe function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Next step to move driver to driver model. Do not use eth_device
structure. Use private structure instead.
Add iobase to private structure to store gem iobase.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add return value for phy detection algorithm to stop init function when
phy is not found.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
We now use the generic delay method which specifies the timeout as
microseconds instead of ticks.
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
The phy can share driver with other aquantia PHYs, so we only
add PHY ID.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
MC 0.7.1.2 enforces limitation i.e.: "Packets may be corrupted
in several combinations of buffer size and frame offsets.
Workaround: Use buffers that are of size that is a multiple of 256, and
frame offset that is a multiple of 256"
Updating the DPNI Eth driver to comply with the restriction.
Signed-off-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add following debug information in the driver
- Get various DPNI counter values
- Get link status of DPNI objects
- Get information of both ends of connection (DPMAC - DPNI)
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As per current implementation of DPAA2 ethernet driver DPNI is used as
net device. DPNI is tangible objects can be multiple connected to same physical lane.
Use DPMAC as net device where it represents physical lane.
Below modification done in driver
- Use global DPNI object
- Connect DPMAC to DPNI
- Create and destroy DPMAC
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's DPAA2 ethernet driver depends upon the static DPL for the
DPRC, DPNI, DPBP, DPIO objects.
Instead of static objects, Create DPNI, DPBP, DPIO objects at run-time.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Management complex Firmware, DPL and DPC are depolyed during u-boot boot
sequence.
Add new DPAA2 commands to manage Management Complex (MC) i.e. start mc, aiop
and apply DPL from u-boot command prompt.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
dpni_create API take takes more time as comapred to existing supported
APIs of MC Flib.
So increase MC command timeout.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DPMAC represents physical line on the board. This physical
line eventually asscociate with on-board PHY.
So Add an api to return linked PHY ID of DPMAC object.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DPMAC object of Management complex controls Physical MAC and MDIO controller.
It provides APIs for MDIO and link state updates. It also provides APIs for
PHY/link configuration.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Current Management Complex Flibs does not support APIs for adding and
destroying the objects.
Add APIs to create and destroy objects for DPBP, DPIO, DPNI and DPRC.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Current implementation only consider SGMIIs for dpmac initialization.
XFI serdes protocols also uses dpmac.
Also, fix lane protocol parsing logic to consider both XFIs and SGMIIs.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Based on spec:
"MDC must not exceed 2.5 MHz (MDC is only active during MDIO read and
write operations)"
Zynq is running on 111MHz. Current setting is 32 which is 111/32=3.47
which is above of 2.5MHz.
Using 48 divider will give us correct setting according spec
(111/48=2.31).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Using set and clear macro is incorrect because it is not overwritting
origin mdc clock division setup.
For example origin setup is 8(0b001) and new setup is 64(0b100) which
means 0b101 is setup which is 96 divider.
Using writel to rewrite all setting like for 1000Mbit/s case.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Zynq has no priority queues.
ZynqMP has one priority queue and this change is required
to get ethernet working.
This patch was not needed on ep108 for uknown reason even
it should be used.
Tested on Zynq and ZynqMP.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Target is duplicating packets. IP prefetches another BD and process it
when the first one is sent. Adding one dummy BD to the chain fix the
problem with packet duplication.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
BD_SEPRN_SPACE should not have hard coded value and it will be
calculated based on the number of buffer descriptors that we
would like to use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Previous loop was completely bogus. Iterration should go just over
statistic counters.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extend comments with register offset to help with debuggging.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
MII is setup by default for all cases. The most of boards are using
RGMII but PHY drivers are not doing any specific setting that's why MII
setting was working fine. With TI DP83867 is necessary to setup
paramaters based on interface type.
Use one setting per board for it which is something what will be removed
when driver is moved to DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add debug messages to phyread/write to help with PHY debug.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Code is taken from Linux kernel driver (v4.2).
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Change ioremap() to map_physmem(), as it is more used in u-boot.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
-> Add National instrument ethernet transceiver configuration used (DP83848)
-> Change cpsw slave phy address
-> modify nand configuration to use the correct ECC and correct nand features
Fix below warnings happening for xilinx_zynqmp_ep_defconfig
drivers/net/zynq_gem.c: In function ‘zynq_gem_init’:
drivers/net/zynq_gem.c:330:7: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
((u32)(priv->rxbuffers) +
^
In file included from drivers/net/zynq_gem.c:19:0:
drivers/net/zynq_gem.c:336:10: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
writel((u32)priv->rx_bd, ®s->rxqbase);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro ‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_send’:
drivers/net/zynq_gem.c:399:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
writel((u32)priv->tx_bd, ®s->txqbase);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro ‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/net/zynq_gem.c:404:22: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
priv->tx_bd->addr = (u32)ptr;
^
drivers/net/zynq_gem.c:409:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
addr = (u32) ptr;
^
drivers/net/zynq_gem.c:414:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
addr = (u32)priv->rxbuffers;
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_recv’:
drivers/net/zynq_gem.c:454:31: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
net_process_received_packet((u8 *)addr, frame_len);
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_initialize’:
drivers/net/zynq_gem.c:533:35: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
priv->rx_bd = (struct emac_bd *)((u32)bd_space + BD_SEPRN_SPACE);
^
drivers/net/zynq_gem.c:533:16: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
priv->rx_bd = (struct emac_bd *)((u32)bd_space + BD_SEPRN_SPACE);
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
The Modular Scatter-Gather DMA core is a new DMA core to work
with the Altera Triple-Speed Ethernet MegaCore. It replaces the
legacy Scatter-Gather Direct Memory Access (SG-DMA) controller
core. Please find details on the "Embedded Peripherals IP User
Guide" of Altera.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Add priv ops to prepare msgdma support. These ops are dma type
specific.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Move the sgdma wait from free_pkt to recv. This is the proper
place to wait recv sgdma done.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Get numbers of fdt address and size cells in altera_tse_probe(),
thereby remove the assumption of one address cell and one size
cell.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Replace numerical bit shift with BIT macro
in altera_tse
:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Remove the useless parenthesis.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use data type u32/u16/u8 for regs and desc, as it is more
portable.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Remove unused macro and regs def.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In pch_gbe_probe(), some additional resources are allocated
(eg: mdio, phy). We should free these in the driver remove phase.
Add pch_gbe_remove() to clean it up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In designware_eth_probe(), some additional resources are allocated
(eg: mdio, phy). We should free these in the driver remove phase.
Add designware_eth_remove() to clean it up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In phy_connect_dev(), if the phy device has an accociated mac device
before, a warning message will be printed. But we should test the
old device against the new one, if they are actually the same one,
don't print the warning message.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In get_phy_device_by_mask(), when no phy is found, currently we only
print a message to show the first phy address that is not found. But
this is not always the case as multiple phys can be specified by
phy_mask. Change to print all phys that are not found, and to reduce
the console boot log, change to use 'debug' instead of 'printf'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In get_phy_device_by_mask(), when no phy is found, we should not
create any phy device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
NAND-tree is used to check wiring between MAC and PHY using NAND gates
on the PHY side, hence the name.
NAND-tree initial status is latched at reset by probing the IRQ pin.
However some devices are sharing the PHY IRQ pin with other peripherals
such as Atmel SAMA5D[34]x-EK boards when using the optional TM7000
display module, therefore they are switching the PHY in NAND-tree test
mode depending on the current IRQ line status at reset.
This patch ensure PHY is not in NAND-tree test mode only for the Micrel
KSZ8051 PHY used by Atmel. There are other Micrel PHY affected but I
doubt they are used on such weird hardware design.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Casting from dev->priv to pci_dev_t changes the value's size on a 64-bit
system. This causes the compiler to complain about casting a pointer to an
integer of a different (smaller) size. To avoid this, cast to an integer
of matching size first, then perform an int->int cast to perform the size
change. This signals explicitly that we do want to change the size, and
avoids the compiler warning. This is legitimate since we know the pointer
actually stores a small integer, not a pointer value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for Micrel KSZ8021RNL & KSZ8031RNL.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
QSGMII PCS needed to be programmed same as SGMII PCS, and there are
four ports in QSGMII PCS, port 0, 1, 2, 3, all the four ports shared
port 0's MDIO controller, so when programming port 0, we continue to
program other three ports.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fsl_dtsec.h & fsl_tgec.h & fsl_fman.h can be shared on both ARM
and PPC, move it out of ppc to include/, and change the path in
drivers accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
codes related to phylib operations should be wrapped by CONFIG_PHYLIB.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In convention, the '0' is a normal return value indicating there isn't
an error. While some functions of FMan IM driver treat '0' as an error
return value.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The FMan IM driver is developed for 32-bit platfroms and isn't
friendly to 64-bit platforms, so do the minimal refactor:
1. Refine the MURAM management and access.
2. Correct the initialization and operations for QDs and BDs.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Frame Manager(FMan) is a big-endian peripheral, so the
registers, internal MURAM and BDs, which are allocated in main
memory and used to communication between core and FMan, should
be accessed in big-endian. The big-endian platforms can access
them directly as the code implemented so far, while for the
little-endian platforms it need to swap the byte-order.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Currently ldpaa ethernet driver rely on DPL file to statically configure
mac address for the DPNIs. It is not a correct approach.
Add support setting MAC address from env variable or Random MAC address.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Convert altera_tse to driver model and phylib.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
remove unused code as the same is achieved when configuring sgmii
and link status is verifed.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In K2G, Ethernet doesn't support SGMII instead it support RGMII,
adding support to the driver to connect to RGMII phy.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Phy mode is a board property and it can be different between
multiple board and ports, so it should not be hardcoded in
driver to one specific mode. So adding a field in eth_priv_t
structure to pass phy mode to driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch uses the eth_is_active() function to work around
issues that prevented compilation with the newer driver model.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently when phy device is created the link variable is
initialized to 1 which denoted phy link is already up. On a power
reset there is no issue as phy status register link status will
not be set, so phy auto negotiate will be started. But when a cpu
reset is issued (ex: dra72x-evm) phy's link status bit is already
set which leads to assume that link is already setup in
genphy_update_link() initial check which results in ehternet not
working. So do not assume that link is already up and on phy
device create set link to zero. This is verified on dra72x-evm.
Reported-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The command:
ethsw [port <port_no>] ingress filtering
{ [help] | show | enable | disable }
- enable/disable VLAN ingress filtering on port
can be used to enable/disable/show VLAN ingress filtering on a port.
This command has also been added to the ethsw generic parser
from common/cmd_ethsw.c
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The command:
ethsw vlan fdb { [help] | show | shared | private }
- make VLAN learning shared or private"
configures the FDB to share the FDB entries learned on multiple VLANs
or to keep them separated. By default, the FBD uses private VLAN
learning. This command has also been added to the ethsw generic parser
from common/cmd_ethsw.c
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The new added commands can be used to configure VLANs for a port
on both ingress and egress.
The new commands are:
ethsw [port <port_no>] pvid { [help] | show | <pvid> }
- set/show PVID (ingress and egress VLAN tagging) for a port;
ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> }
- add a VLAN to a port (VLAN members);
ethsw [port <port_no>] untagged { [help] | show | all | none | pvid }
- set egress tagging mod for a port"
ethsw [port <port_no>] egress tag { [help] | show | pvid | classified }
- Configure VID source for egress tag. Tag's VID could be the
frame's classified VID or the PVID of the port
These commands have also been added to the ethsw generic parser from
common/cmd_ethsw.c
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The new command:
ethsw [port <port_no>] [vlan <vid>] fdb
{ [help] | show | flush | { add | del } <mac> }
Can be used to add and delete FDB entries. Also, the command can be used
to show entries from the FDB tables. When used with [port <port_no>]
and [vlan <vid>], only the matching the FDB entries can be seen or
flushed. The command has also been added to the generic ethsw parser
from cmd_ethsw.c.
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The command:
ethsw [port <port_no>] learning { [help] | show | auto | disable }
can be used to enable/disable HW learning on a port.
This patch also adds this command to the generic ethsw parser from
cmd_ethsw.
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The new added command:
ethsw [port <port_no>] statistics { [help] | [clear] }
will print counters like the number of Rx/Tx frames,
number of Rx/Tx bytes, number of Rx/Tx unicast frames, etc.
This patch also adds this commnd in the genereric ethsw
parser from cmd_ethsw.c
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch replaces the parser used by VSC9953 L2 Switch driver with
the generic one. Also, the config macro that enables the
VSC9953 commands has been replaced in all the platforms that
use this driver with the config macro that corresponds to the
generic parser.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
At startup, the default configuration should be:
- enable HW learning on all ports (HW default);
- all ports are VLAN aware;
- all ports are members of VLAN 1;
- all ports have Port-based VLAN 1;
- on all ports, the switch is allowed to remove
maximum one VLAN tag,
- on egress, the switch should add a VLAN tag if the
frame is classified to a different VLAN than the port's
Port-based VLAN;
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When a port is enabled at init time, the initializing function
touches more bits than necessary to enable a port (also touches
reserved bits and default bit values). This patch fixes this issue
by changing the value of the define used to enable the port and
assures that no other bits are changes by replacing out_le32()
with setbits_le32().
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch groups some macros defined for registers and
replaces some magic numbers from vsc9953 with macros. Also,
"port" and "port_nr" words are replaced with "port_no",
puts each variable declaration on a line and removes
unnecessary tabs.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Designware ethernet controller is also seen on PCI bus, e.g.
on Intel Quark SoC. Add this support in the DM version driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.
Signed-off-by: Simon Glass <sjg@chromium.org>
When building dm version of designware eth driver on a platform
with 64-bit phys_addr_t, it reports the following warnings:
drivers/net/designware.c: In function 'designware_eth_probe':
drivers/net/designware.c:599:2:
warning: format '%lx' expects argument of type 'long unsigned int',
but argument 3 has type 'phys_addr_t' [-Wformat]
drivers/net/designware.c:600:21:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/net/designware.c:601:21:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
This commit fixes the build warnings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit converts pch_gbe ethernet driver to driver model.
Since this driver is only used by Intel Crown Bay board, the
conversion does not keep the non-dm version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Zap variable which is set but never used.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
The MIB RAM and FIFO receive start register does not exist on
i.MX6UL. Accessing these register will cause enet not work well.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Stefano Babic <sbabic@denx.de>
Replace the DMACTRL[LE] hack with recommended settings
for ETSECDMAMCR to get the same end effect - obtaining
big-endian buffer descriptors and frame data for eTSEC.
The reset / default value for ETSECDMAMCR is preserved,
excepting the BD and FR bits which are cleared to enable
the BE mode in accordance with the H/W specifications.
Fixes: 52d00a8 "ls102xa: etsec: Add etsec support for LS102xA"
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of VSC8584 phy placed on new QSGMII/SGMII ethernet riser cards
used on LS2085QDS platforms.
Signed-off-by: King Chung Lo@freescale.com <KingChungLo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Recently the FMan Port and MAC compatibles were changed.
This patch aligns the FMan Port and MAC compatibles
to the new FMan device tree binding document.
The FMan device tree binding document can be found in the Linux kernel:
./Documentation/devicetree/bindings/powerpc/fsl/fman.txt
This patch doesn't affect legacy compatibles support.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Tested-by: Xing Lei <xing.lei@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
commit 6497e37 "net: e1000: Support 64-bit physical address" causes
compiler warnings on 32-bit U-Boot build below.
drivers/net/e1000.c: In function 'e1000_configure_tx':
drivers/net/e1000.c:4982:2: warning: right shift count >= width of type [enabled by default]
drivers/net/e1000.c: In function 'e1000_configure_rx':
drivers/net/e1000.c:5126:2: warning: right shift count >= width of type [enabled by default]
This commit fixes the build warnings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add Kconfig options in preparation for moving boards to use Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Update this driver to support driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
Since struct eth_device does not exist with CONFIG_DM_ETH defined, avoid
using it in the driver unless necessary. Most of the time it is better to
pass the private driver pointer anyway.
Also refactor the code so that code that the driver model implementation
will share are available in functions that can be called. Add stubs where
necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
We cannot currently include any header files in the C files since common.h
needs to be included first, and it is in the header file. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
High 32-bit address is needed when u-boot runs in 64-bit space.
Tested on armv8-based LS2085ARDB.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables the NAND controller on the Armada XP/38x and provides
a new function that returns the NAND controller input clock. This
function will be used by the MVEBU NAND driver.
As part of this patch, the multiple BIT macro definitions are moved
to a common place in soc.h.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Morrow <peter@senient.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add support to specify the Ethernet buffer base address;
if none are supply by the board, the default value is use (from existing code).
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The current 4.5 timeout for the autonegotiation are not enough to
complete it on my platform. Using the Intel E1000 PCIe card in the
Marvell db-mv784mp-gp eval board. So lets increase the timeout to
8 seconds.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
Add Ethernet PHY for BCM Cygnus SoC
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With commit e3a77218a2 the MII bus is only
reset if a reset handler is registered. If there is no reset handler there
is no need to wait for a device to come out of the reset.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
The rxbd is not correctly handled in case of a frame physical error
(FPE) or frame size error (FSE). The rxbd must be cleared and
advanced in case of an error to avoid receive stall.
Signed-off-by: Daniel Inderbitzin <daniel.inderbitzin@gmail.com>
LPC32xx MAC and clock control configuration requires some minor quirks
to deal with a phy connected by RMII.
It's worth to mention that the kernel and legacy BSP from NXP sets
SUPP_RESET_RMII == (1 << 11) bit, however the description of this bit is
missing in shared LPC32x0 User Manual UM10326 Rev. 3, July 22, 2011
and in LPC32x0 Draft User Mannual Rev. 00.27, November 20, 2008, also
in my tests an SMSC LAN8700 phy device connected over RMII seems to
work correctly without touching this bit.
Add support of RMII, if CONFIG_RMII is defined, this option is aligned
with a number of boards, which already define the same config value.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
This change rearranges general MAC configuration and PHY specific
configuration of MAC registers (duplex mode and speed), before this
change set bits related to PHY configuration in MAC2 and COMMAND
registers are rewritten by the following writing to the registers.
Without the change auto negotiation on boot quite often is not
completed in reasonable time:
Waiting for PHY auto negotiation to complete......... TIMEOUT !
Additionally MAC1_SOFT_RESET clear bit is removed since it is done in
preceding lpc32xx_eth_initialize() and in lpc32xx_eth_halt(), instead
added missing MCFG_RESET_MII_MGMT on device initialization.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The lpc32xx_eth_phylib_init() function is capable to connect LPC32XX
MAC to some specified phy by phy id, by chance the single user of
lpc32xx_eth has CONFIG_PHY_ADDR set to 0, however other boards may
have non-zero CONFIG_PHY_ADDR value, fix it.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
According to LPC32x0 User Manual the following bits in Command
register 0x3106_0100 are defined:
Bit Symbol
2 - Unused
3 RegReset
4 TxReset
5 RxReset
Fix wrong (1-bit shifted right) COMMAND_RESETS value, which sets
an unused bit, but neglects RxReset.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tearing down an unitialized rx channel causes a pending address hole
event to be queued. When booting linux it will report this pending
as something like "Address Hole seen by USB_OTG at address 57fff584",
since u-boot did not handled this interrupt. Prevent that by not
tearing down the rx channel, when not receiving.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Support the 88E1510 PHY which is very similar to the 88E1518.
I also set the INTn output and configured the LEDs.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- The EEE fixup magic should also be enabled for RGMII
- Improved comments
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch refer to linux kernel commit: d8b763e1e79f
net/macb: add TX multiqueue support for gem
by: Cyrille Pitchen
1. macb driver will check the register to find how many queues support for
this chip.
2. Then as we only use queue0 for tx, so we will set up all other queues
use a dummy descriptor, which USED bit is set. So those queues are not used.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
remove unnecessary clearing of SWSM.SWSM_SMBI when obtaining the SW
semaphore. This was introduced in 951860634f
while adding i210 support and should be now resolved by releasing the
semaphore when no longer needed.
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This reverts commit 17da712024.
The i210/i211 do have the SW_FW_SYNC (0x5b5c) register and this is what should
be used when acquiring the semaphore.
I believe the issue that this patch was trying to resolve is now resolved
by properly releasing the semaphore once no longer needed.
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Once the hwsw semaphore is acquired, it must be released when access to the
hw is completed. Without this subsequent calls to acquire will timeout
obtaining the semaphore.
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The driver variable name is eth_sandbox, which is probably a copy-paste
mistake. Fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the OF compatible property to match the SoCFPGA GMAC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
MC firware version 8.0.0 contains new command flags. This patch
contains modifications in FLIB files to support the new command flags.
Signed-off-by: Itai Katz <itai.katz@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increase the Rx Buffer descriptors to 32. This will avoid
Rx buffer descriptors overflow if more packets were received
at one shot before we process the received ones.
This fixes the issue of intermittent timeouts during tftp
on a 1Gb connection with tftp server running on windows.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Flush and invalidate the rx buffers while sending the
tx packet it self as armv8 does flush also while doing
invalidation.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set the data bus width to 64-bit AMBA Databus width in config register.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The MCAST_TFTP support requires that network drivers has mcast functon
implemented. This commit adds dummy keystone2_eth_bcast_addr() to meet
the requirement. As far as the driver doesn't use ALE and doesn't filter
any incoming packets, the function is empty.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some devices can take a long time to work out whether they have a new packet
or now. For example the ASIX USB Ethernet dongle can take 5 seconds to do
this, since it waits until it gets a new packet on the wire before allowing
the USB bulk read packet to be submitted.
At present with driver mode the Ethernet receive code reads 32 packets. This
can take a very long time if we must wait for all 32 packets. The old code
(before driver model) worked by reading a single set of packets from the USB
device, then processing all the packets with in. It would be nice to use
the same behaviour with driver model.
Add a flag to the receive method which indicates that the driver should try
to find a packet if available, by consulting the hardware. When the flag is
not set, it should just return any packet data it has already received. If
there is none, it should return -EAGAIN so that the loop will terminate.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver is used by the Intel Minnowmax board. Convert it to driver model
so it can use the new Ethernet implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Change infinite loop mechanism to timer based polling for QBMAN release in
ldpaa_eth_rx.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Polling of TX conf frames is not a mandatory option.
Packets can be transferred via WRIOP without TX conf frame.
Configure ldpaa_eth driver to use TX path without confirmation frame
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Volatile command does not return frame immidiately, need to wait till a frame
is available in DQRR. Ideally it should be a blocking call.
Add timeout handling for DQRR frame instead of retry counter.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Do not immediately return if the enqueue function returns -EBUSY; re-try
mulitple times.
if timeout occures, release the buffer.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
delete any existing ICID pools in the DPC and create
a new one based on the stream ID partitioning for
the SoC
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Stream IDs on ls2085a devices are not hardwired and are
programmed by sw. There are a limited number of stream IDs
available, and the partitioning of them is scenario dependent.
This header defines the partitioning between legacy, PCI,
and DPAA2 devices.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Management complex major version should match to the firmware present in flash.
Return error during mismatch of major version.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update qbman driver
- As per latest available qbman driver
- Use of atomic APIs
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Geoff Thorpe <Geoff.Thorpe@freescale.com>
CC: Haiying Wang <Haiying.Wang@freescale.com>
CC: Roy Pledge <Roy.Pledge@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update flibs changes to mc-0.6.0.1 for dpmang, dprc, dpni and dpio objects
Also rename qbman_portal_ce/ci_paddr to qbman_portal_ce/ci_offset in
dpio_attr. These are now offsets from the SoC QBMan portals base.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Load AIOP image from NOR flash into DDR so that the MC firmware
the MC fw can start it at boot time
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Flush buffer before releasing to BMan after TX_conf to ensure, the core does
not have any cachelines that the WRIOP will DMA to.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Make it easier for the user to notice when the MC firmware
had problems booting.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch fixes the DDR hide logic for LS2085a, correcting the way
the Debug Server FW and MC FW images are placed on the top of system
DDR and how the rest of the system DDR space is made visibile to Linux.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This locally defined struct is actually only used once
and as an opaque type. Remove it for clarity.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
commit f566c99 "net: Update hardware MAC address if it changes in env"
removes writing MAC address to designware controller after soft reset.
This makes designware ethernet port fail to work. Actually the MAC
address should always be programmed after soft reset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove the calls to net_random_ethaddr() that some boards and some
drivers are calling. This is now implemented inside of net/eth.c
Enable the feature for all boards that previously enabled it.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-By: Michael Walle <michael@walle.cc> (for the lsxl board part)
Series-changes: 2
-Fixed bfin build errors
We really don't want boards defining fixed MAC addresses in their config
so we just remove the option to set it in a fixed way. If you must have
a MAC address that was not provisioned, then use the random MAC address
functionality.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Targets with CONFIG_NEEDS_MANUAL_RELOC do not use REL/RELA
relocation (mostly only GOT) where functions aray are not
updated. This patch is fixing function pointers passed to phy_register
function.
This patch was tested on Microblaze architecture.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
RTL8211F needs to enalbe TXDLY for RGMII during
phy initialization, so move it to rtl8211f_config
for early initialization.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When the ethaddr changes in the env, the hardware should also be updated
so that MAC filtering will work properly without resetting U-Boot.
Also remove the manual calls to set the hwaddr that was included in a
few drivers as a result of the framework not doing it.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
RTL8211F has different registers from RTL8211E.
This patch adds support for RTL8211F PHY which
can be found on Freescale's T1023 RDB board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When called, the next call to receive will trigger a 10-second leap
forward in time to avoid waiting for time to pass when tests are
evaluating timeout behavior.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
All sunxi boards now use the driver-model, so remove the non driver-model
code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Modify the sunxi-emac eth driver to support driver model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
Besides being spelled wrong, the DMA_CPU_TRRESHOLD define actually has
nothing to do with DMA as we only use mmio fifo access. Rename it to
EMAC_RX_BUFSIZE to properly reflect what it does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
Split all the core functionality out into functions taking a
struct emac_eth_dev *priv argument as preparation for adding driver-model
support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a preparation-patch for adding device-model support to the emac
driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support of ethernet:
- eth.c: mapping lane to slot for (0x2A, 0x07)
- ls2085a.c: To enable/disable dpmac and get link type
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Wire rate IO Processor (WRIOP) provide support of receive and transmit
ethernet frames from the ethernet MAC. Here Each WRIOP block supports
upto 64 DPMACs.
Create a house keeping data structure to support upto 16 DPMACs and
store external phy related information.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The memac for PHY management on little endian SoCs is similar on big
endian SoCs, so we modify the driver by using I/O accessor function to
handle the endianness, so the driver can be reused on little endian
SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian
SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access
is little endian, if not, the I/O access is big endian. Move fsl_memac.h
out of powerpc include.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Changed MC firmware loading to comply with the new MC boot architecture.
Flush D-cache hierarchy after loading MC images. Add environment
variables "mcboottimeout" for MC boot timeout in milliseconds,
"mcmemsize" for MC DRAM block size. Check MC boot status before calling
flib functions.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Fix comilation warning which is emitted when
firmware address is more than 32 bit.
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Fix flush_dcache_range() input parameter to use start and end addresses.
Change ethernet interface name to DPNI. Update entry criteria for
ldpaa_eth_stop. Ethernet stack first stop the device before performing
next operation. At the time of Ethernet driver registration,
net_dev->state is set as ETH_STATE_INIT So take care net_dev->state as
ETH_STATE_INIT in ldpaa_eth_stop.
Undef CONFIG_PHYLIB temorarily because ldpaa_eth driver currently does
not support PHYLIB.
Instead of clearing pull descriptor one time, clear it before issuing any
volatile dequeue command.
Volatile command does not return frame immidiately, wait till a frame
is available in DQRR. This frame can be valid or expired.
Flush buffer before releasing to BMan ensure the core does not have any
cachelines that the WRIOP will DMA to.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Roy Pledge <Roy.Pledge@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The patch removes unnecessary whitespace to fix checkpatch's
warning: unnecessary whitespace before a quoted newline
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LDPAA Ethernet driver is a freescale's new ethernet driver based on
Layerscape architecture.
Every ethernet driver controls on DPNI object. Where all DPNIs share
one common DPBP and DPIO object to support Rx and Tx flows.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Cristian Sovaiala <cristian.sovaiala@freescale.com>
CC: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
CC: J. German Rivera <German.Rivera@freescale.com>
[York Sun: s/NetReceive/net_process_received_packet]
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's Layerscape Management Complex (MC) provide support various
objects like DPRC, DPNI, DPBP and DPIO.
Where:
DPRC: Place holdes for other MC objectes like DPNI, DPBP, DPIO
DPBP: Management of buffer pool
DPIO: Used for used to QBMan portal
DPNI: Represents standard network interface
These objects are used for DPAA ethernet drivers.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:
MC DDR region start = Top of DDR - area reserved by Debug Server FW
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The name "pch_gbe.%x" exceeds the limit of the name in the
'struct eth_device'. Rename it as just "pch_gbe".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
commit 3c6928fd7b "net: phy: fix warnings with W=1" caused
some PHYs(e.g. CS4315/CS4340) not working. This patch fixes the
warning and make those special PHYs working as well.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Turn ioaddr into an unsigned long rather than a sized 32-bit variable.
While at it, fix a couple of pointer to integer cast size mismatch
warnings by casting through unsigned long going from pointers to
integers and vice versa.
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some Realtek Ethernet PHYs, like RTL8211D(G/N) and RTL8211E(G), have
interrupts enabled by default. If the interrupt is not treated later by
the OS and the PHY's interrupt line is enabled and shared with other
interrupts, the system will get an interrupt storm. This patch disables
the interrupt for PHY devices that use one of the current Realtek
Ethernet PHY drivers. Some of Realtek Ethernet PHYs, such as RTL8211B(L)
have the interrupt masked. In this case, the functionality of the PHY
should not be afected since this patch brings INER and INSR registers to
their default values.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add driver model support to the designware driver. This reuses most of the
existing code except for some duplication in the probe() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adjust the error handling to use errno.h instead of returning -1. Change
leaf functions to pass in the arguments they require rather than struct
eth_device. Apart from simplifying the code it makes is easier to reuse
these functions for driver model, since mostly they actually only use
struct dw_eth_priv (which we can keep).
Create a stub for each Ethernet operation function. This will allow use to
share code with the driver model versions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When driver model is used for Ethernet a few functions are passed a udevice
instead of an eth_device. Also add a function to find a PHY type given its
name. This will be used to decode the device tree node.
Finally, put a phy_interface field in struct eth_pdata since this is an
important part of the platform data for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Finish eliminating CamelCase from net.c and other failures
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within netconsole.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch cleans up the names of internal packet buffer names that are
used within the network stack and the functions that use them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch is simply clean-up to make the IPv4 type that is used match
what Linux uses. It also attempts to move all variables that are IP
addresses use good naming instead of CamelCase. No functional change.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
The 'lo' interface on Linux doesn't support thinks like ARP or
link-layer access like we use to talk to a normal network interface.
A higher-level network API must be used to access localhost.
As written, this interface is limited to not supporting ICMP since the
API doesn't allow the socket to be opened for all IP traffic and be able
to receive at the same time. UDP is far more useful to test with, so it
was selected over ICMP. Ping won't work, but things like TFTP should
work.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement a bridge between U-Boot's network stack and Linux's raw packet
API allowing the sandbox to send and receive packets using the host
machine's network interface.
This raw Ethernet API requires elevated privileges. You can either run
as root, or you can add the capability needed like so:
sudo /sbin/setcap "CAP_NET_RAW+ep" /path/to/u-boot
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is needed to test the netretry functionality (make the command fail
on a sandbox eth device).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sandbox driver will now generate response traffic to exercise the
ping command even when no network exists. This allows the basic data
pathways of the DM to be tested.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic network support to sandbox which includes a network driver.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This value is not used by the network stack and is available in the
global data, so stop passing it around. For the one legacy function
that still expects it (init op on old Ethernet drivers) pass in the
global pointer version directly to avoid changing that interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Trival fix to remove an unneeded variable declaration in 4xx_enet.c)
Each hardware feature exposed through the GPIO pin mux is usually using the same
function index (for a given port), so there is no need to define one value per
pin: one value per hardware feature per port is sufficient, avoids duplication
and makes everything easier to understand.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a new driver for the Gigabit Ethernet MAC found on Intel Topcliff
Platform Controller Hub. Tested under 10/100 half/full duplex and 1000
full duplex modes using ping and tftpboot commands.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some ethernet drivers use their own version of ethernet FCS length
macro which is really common. We define ETH_FCS_LEN in net.h and
replace those custom versions in various places.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If the GBE bit is set, when do next time autonegotiation,
if the result is not 1000Mbps, it will fallback to 100Mbps
checking. So, we need to clear the GBE bit.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Board can define its own AXI burst length to improve DWMAC DMA performance.
v2-changes:
- Avoid write burst len register when the Macro is not defined.
v3-changes:
- Add axi_bus register member to struct eth_dma_regs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
Acked-by: Marek Vasut <marex@denx.de>
Upgrade Manage Complex (MC) flib API to 0.5.2. Rename directory
fsl_mc to fsl-mc. Change the fsl-mc node in Linux device tree
from "fsl,dprcr" to "fsl-mc". Print MC version info when
appropriate.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On Keystone2 devices serdes must be initialized before accessing MDIO bus.
This commit moves the keystone2_net_serdes_setup() from keystone2_eth_open
to keystone2_emac_initialize to meet that requirement.
This also eliminates unnecessary serdes initializatin every time when the
keystone2_eth_open is being called.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Nishanth Menon <nm@ti.com>
If for some reason DMA module fails to reset user oserves only this:
--->---
# dhcp
Trying dwmac.e0018000
FAIL
--->---
This message makes not much sense.
With proposed change error message will be more helpful:
--->---
# dhcp
Trying dwmac.e0018000
DMA reset timeout
FAIL
--->---
For example user may do power toggle to recover board functionality.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a phy driver for the Micrel KSZ8895 switch. As the SoC MAC
is directly connected to the switch MAC the link to the switch is always up.
But the KSZ8895 switch can be hardwired in three configuration modes :
- not configurable with eventually an eeprom-stored configuration
- configurable by the mdio/mdc connection (SMI protocol)
- configurable by a SPI connection.
In not configurable mode, the switch starts automatically, but in the
other modes, it must be started programmatically, by writing 1 in
configuration register 1.
We only support the not configurable and mdio/mdc (aka SMI) modes here.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
If the PHY is not recognized don't access phydev (NULL)
and return 0 to signal failure.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Each board with defines it's own set of values. If we do not define
CONFIG_MVGBE_PORTS we will hit following error:
mvgbe.c: In function 'mvgbe_initialize':
mvgbe.c:700:34: error: 'CONFIG_MVGBE_PORTS' undeclared (first use in this function)
u8 used_ports[MAX_MVGBE_DEVS] = CONFIG_MVGBE_PORTS;
This patch fixes above described problem.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This patch fix the compilation warning
w+../drivers/net/xilinx_ll_temac.c: In function 'll_temac_init':
w+../drivers/net/xilinx_ll_temac.c:235:3: warning: format '%X' expects
argument of type 'unsigned int', but argument 4 has type 'phys_addr_t'
[-Wformat]
introduced by
"net: Declare physical address as phys_addr_t unsigned type"
(sha1: 16ae782722).
Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds a driver for VSC9953 L2 Switch. This Vitesse IP
is integrated in Freescale T1040 and T1020 SoCs.
The L2 switch has 10 Ethernet ports: 2 internal fixed-links
(ports 8 and 9) at 2.5 Gbps and and 8 external ports at 1 Gbps.
The external ports may be connected to PHYs over QSGMII and SGMII.
Commands have also been added to enable/disable a port and to
check a port's link speed, duplexity and status. The commands are:
ethsw port <port_nr> enable|disable - enable/disable an l2 switch port
ethsw port <port_nr> show - show an l2 switch port's configuration
port_nr=0..9; use "all" for all ports
For more detailse please see doc/README.t1040-l2switch
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If SerDes is configured to connect L2 Switch ports from T1040
over SGMII or QSGMII, the two FMAN fixed ports (FM1@DTSEC1 and FM2@DTSEC2)
that are connected to two L2 swtch ports must be enabled. These
ports don't have PHYs and must be treated accordingly.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-boot assumes that all FMAN ports have a PHY. Some SoCs (like T1040)
have fixed links. This means that the ports are connected MAC to MAc
and there is no Ethernet PHY attatched. This patch initializes a
FMAN MAC even if it doesn't have a PHY attached.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch supports AQ1202, AQ2104, AQR105 PHY.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
This network interface card is found on the NVIDIA Jetson TK1.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
To work around potential issues with explicit cache maintenance of the
RX and TX descriptor rings, allocate them from a pool of uncached memory
if the architecture supports it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
RX and TX descriptor rings should be aligned to 256 byte boundaries. Use
the DEFINE_ALIGN_BUFFER() macro to define the buffers so that they don't
have to be manually aligned later on. Also make sure that the buffers do
align to cache-line boundaries in case the cache-line is higher than the
256 byte alignment requirements of the NIC.
Also add a warning if the cache-line size is larger than the descriptor
size, because the driver may discard changes to descriptors made by the
hardware when requeuing RX buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
According to the top-level README file, this configuration setting can
be used to override the number of receive buffers that an ethernet NIC
uses.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
we need to differentiate dual-role MACs into two types: MACs with
10GEC enumeration consistent with DTSEC enumeration(defined by
CONFIG_FSL_FM_10GEC_REGULAR_NOTATION) and other MACs without
CONFIG_FSL_FM_10GEC_REGULAR_NOTATION defined.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
VSC8514 QSGMII PHY requires enabling auto-negotiation,
otherwise it wouldn't work.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER.
but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs.
on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
10GEC1->MAC1, 10GEC2->MAC2
so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on
which 10GEC enumeration is consistent with MAC enumeration.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Freescale T1024/T1023 SoC.
The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
- Three PCI Express 2.0 controllers
- Additional peripheral interfaces
- One SATA 2.0 controller
- Two USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/eSDHC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T1024 and T1023:
Feature T1024 T1023
QUICC Engine: yes no
DIU: yes no
Deep Sleep: yes no
I2C controller: 4 3
DDR: 64-bit 32-bit
IFC: 32-bit 28-bit
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card
slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This
Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified
string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp
respectively in hwconfig.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We need following changes to make xfi work on B4:
1. set cross-point switch VSC3308 to use sfp config when running xfi;
2. add 10G interface check for xfi;
3. set phy address for xfi so the 10G ports can be registered by mdio;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
fman_port_enet_if() tests if FM1_DTSEC2 or FM1_DTSEC4 uses
RGMII or MII and if not returns PHY_INTERFACE_MODE_NONE.
This excludes testing for SGMII further down.
Remove the unconditional "else return PHY_INTERFACE_MODE_NONE"
so SGMII can be tested too.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
As auto-negotiation is not supported for 2.5G SGMII, we need
to add a new type PHY_INTERFACE_MODE_SGMII_2500 to differentiate
SGMII-1G and SGMII-2.5G with different setting for auto-negotiation.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The User Register in GMAC IP is used to select interface type.
When with GE feature, it is used to select interface between
RGMII and GMII. If without GE feature, it is used to select
interface between MII and RMII.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
When boot up without mac address setting, it will give the warning
message like: "Warning: failed to set MAC address", however when
execute network related command, it still execute them without any
warning information.
With this patch, it will exit directly with following information:
"gmac0: mac address is not valid"
It also solve the problem after bootup then set mac address and the
mac address won't set to net device issue.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
NEG bit default is '1' for external MDIOs as per FMAN-v3 RM, but on some
platforms, e.g. T2080QDS, this bit is '0', which leads to MDIO failure
on XAUI PHY, so set this bit definitely to align with the RM.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. use Payload length check disable when enable MAC;
2. add XGMII support for setting MAC interface mode;
3. only enable auto negotiation for Non-XGMII mode;
4. return 0xffff if clause 22 is used to read 10G phy_id;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-By: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Fix error detected by cppcheck:
[drivers/net/uli526x.c:551]: (error) printf format string requires 3
parameters but only 2 are given.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Make sure to keep the MAC address programmed in the SMC911x ADDRH
and ADDRL registers. Linux can read those registers to determine
the MAC address on EEPROM-less configurations.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@ti.com>
As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/88E1514
Rev A0, Errata Section 3.1 Marvell PHY has an errata which requires
that certain registers get written in order to restart
autonegotiation.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Keystone2 Lamar SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2L SoCs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Lamar SoC uses the same keystone SerDes driver.
All Keystone2 EVM boards currently use SerDes driver, so move
CONFIG_TI_KEYSTONE_SERDES to common configuration file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
A bit field of DMA descriptor is on memory area of DMA. If we set data
to bit of DMA descriptor, we must be writeback data of DMA descriptor.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
RX_DESC_SIZE and TX_DESC_SIZE mean the size of the data descriptor for sh-eth.
We can acquire this in sizeof. It is not necessary to define these in define.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
R8A7793 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7793.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
I finally had a look at the datasheet and spotted an additional
register address difference between regular E1000 and i210/i211 chips.
This patch fixes this and now successfully works on programmed
i210/i211 as well as unprogrammed i211.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Commit 951860634f may have changed
the logic unintentially from "if (!(swfw_sync & (fwmask | swmask)))"
to "if ((swfw_sync & swmask) && !(swfw_sync & fwmask))". This change
breaks some e1000 NIC with a message "ERROR: Unable to read EEPROM!".
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Marek Vasut <marex@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
Acked-by: Marcel Ziswiler <marcel@ziswiler.com>
The file board/Marvell/include/mv_gen_reg.h is incompatible with
the GPL (see for example the "MARVELL RESERVES THE RIGHT AT ITS SOLE
DISCRETION TO REQUEST THAT THIS CODE BE IMMEDIATELY RETURNED TO
MARVELL" clause). As this cannot be fixed, we remove the file and all
code that depends on it. Fortunately this only affects some very old
boards that have long reached EOL:
CPCI750
DB64360
DB64460
p3m750
p3m7448
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
get_phy_id is marked weak but has no protype nor a
strong version, just make it static. Use __weak for
board_phy_config.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
The new Marvel PHY (88E1514) used on K2L/K2E EVM requires longer time
to auto negotiate with SoC's SGMII port.
It can take about 3 sec to up the PHY after reset, so add code to
expose sgmii auto negotiation waiting process.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The Keystone2 Edison SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2E SoCs.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Edison SoC uses the same keystone SerDes driver.
This patch adds support for K2E SoCs.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The phy framework has function to get link, so use it
instead of own implementation.
There is no reason to check SGMII link while sending each
packet, phy link is enough. Check SGMII link only while
ethernet open.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
As MDIO bus has been added we can register PHYs with it.
After registration, the PHY driver will be probed according to the
hardware on board.
Startup PHY at the ethernet open.
Use phy_startup() instead of keystone_get_link_status() when eth open,
as it verifies PHY link inside and SGMII link is checked before.
For K2HK evm PHY configuration at init was absent, so don't enable
phy config at init for k2hk evm.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Currently MDIO framework is not used to configure Ethernet PHY.
As result some of already implemented functions are duplicated.
So register MDIO bus in order to use it. On that stage it's just
registered, it'll be used as we start to use PHY framework.
Use mdio bus read/write/reset functions in the driver.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Don't use mdio_enable twice while eth open. Also rename it to
keystone2_mdio_reset as more appropriate name.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
In case when several Ethernet ports are supported it's
convenient to see the number of phy that is not found.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
SerDes driver is used by other sub systems like PCI, sRIO etc.
So modify it to be more general. The SerDes driver provides common
API's that can also be extended for other peripherals SerDes
configurations.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch split the Keystone II SGMII SerDes related code from
Ethernet driver and create a separate SGMII SerDes driver.
The SerDes driver can be used by others keystone subsystems
like PCI, sRIO, so move it to driver/soc/keystone directory.
Add soc specific drivers directory like in the Linux kernel.
It is going to be used by keysotone soc specific drivers.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Remove unused tx_send_loop variable.
Removes duplicated get_link_status() call from the
keystone2_eth_send_packet().
The emac_gigabit_enable() is called at opening Ethernet and there is no
need to enable it on sending each packet. So remove that call
from keystone2_eth_send_packet() as well.
The calling of power/clock up functions are mostly the responsibility
of SoC/board code, so move these functions to appropriate place.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The header file for the driver should be in correct place.
So move it to "arch/arm/include/asm/ti-common/keystone_net.h"
and correct driver's external dependencies. At the same time
align and correct some definitions.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch removes K2HK SOC specifc emac_regs structure, it uses
soc specific register offset to keep the network driver common across
all the Keystone II EVMs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav driver is general driver intended to be used for
working with queue manager and pktdma for different IPs like NETCP,
AIF, FFTC, etc. So the it's API shouldn't be named like it works only
with one of them, it should be general names. The names with prefix
like netcp_* rather do for drivers/net/keystone_net.c driver. So it's
good to generalize this driver to be used for different IP's and
delete confusion with real NETCP driver.
The current netcp_* functions of keystone navigator can be used for
other settings of pktdma, not only for NETCP. The API of this driver
is used by the keystone_net driver to work with NETCP, so net driver
also should be corrected. For convenience collect pkdma
configurations in drivers/dma/keystone_nav_cfg.c.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav is used by drivers/net/keystone_net.c driver to
send and receive packets, but currently it's placed at keystone
arch sources. So it should be in the drivers directory also.
It's separate driver that can be used for sending and receiving
pktdma packets by others drivers also.
This patch just move this driver to appropriate directory and
doesn't add any functional changes.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds support for the NETA ethernet controller which is integrated
in the Marvell Armada XP SoC's. This port is based on the Linux driver which
has been stripped of the in U-Boot unused portions.
Tested on the Marvell MV78460 eval board db-78460-bp.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Add a few new variables to make the cache handling less cryptic.
Add a variable for DMA and DATA descriptor start and end, so the
correctness of the code is easier to inspect.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Fix remaining cache alignment issues in the DWC Ethernet driver.
Please note that the cache handling in the driver is making the
code hideous and thus the next patch cleans that up. In order to
make this change reviewable though, the cleanup is split from it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Pavel Machek <pavel@denx.de>
Old saying says that more than three exclamation marks in a row are
sign of mental disease. Cleanup micrel.c.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Chin Liang See <clsee@altera.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Fix the following build error in case CONFIG_E1000_NO_NVM is enabled:
CC drivers/net/e1000.o
drivers/net/e1000.c: In function ‘e1000_initialize’:
drivers/net/e1000.c:5365:5: error: ‘struct e1000_hw’ has no
member named ‘eeprom_semaphore_present’
make[1]: *** [drivers/net/e1000.o] Error 1
make: *** [drivers/net] Error 2
Acked-by: Marek Vasut <marex@denx.de>
T1042QDS (T1042 is T1040 Personality without L2 switch) supports following
sgmii interfaces with serdes protocol 0xA7
-SGMII-MAC3 on Lane B - slot 7
-SGMII-MAC5 on Lane H - slot 7
-SGMII2.5G-MAC1 on Lane C - slot 6
-SGMII2.5G-MAC2 on Lane D - slot 5
Add support of above sgmii interfaces
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
When network protocol errors occur (such as a file not being found on a
TFTP server), the processing done by the NetReceive() function will end
up calling the driver's .halt() implementation. However, after that the
device no longer has access to the memory buffers and will cause errors
such as this in the rtl_recv() function when trying to hand descriptors
back to the device:
pci_hose_bus_to_phys: invalid physical address
This can be fixed by deferring processing of network packets until the
descriptors have been handed back. That way rtl_halt() tearing down
network buffers is not going to prevent access to the buffers.
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use size_t type for positive offsets instead of the loff_t type. The
later is defined as long long, which is larger than the pointer type
on OpenRISC architecture and therefore the following warning was
generated:
"warning: cast to pointer from integer of different size"
Signed-off-by: Vasili Galka <vvv444@gmail.com>
When testing the FEC driver on a mx6solox we noticed that the TDAR bit gets
always cleared prior then the READY bit is cleared in the last BD, which causes
FEC packets reception to always fail.
As explained by Ye Li:
"The TDAR bit is cleared when the descriptors are all out from TX ring, but on
mx6solox we noticed that the READY bit is still not cleared right after TDAR.
These are two distinct signals, and in IC simulation, we found that TDAR always
gets cleared prior than the READY bit of last BD becomes cleared.
In mx6solox, we use a later version of FEC IP. It looks like that this
intrinsic behaviour of TDAR bit has changed in this newer FEC version."
Fix this by polling the READY bit of BD after the TDAR polling, which covers the
mx6solox case and does not harm the other SoCs.
No performance drop has been noticed with this patch applied when testing TFTP
transfers on several boards of different i.mx SoCs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
mx6solox has a requirement for 64 bytes alignment for RX DMA transfer.
Other SoCs work with the standard 32 bytes alignment.
Adjust it accordingly by using 64 bytes aligment in the FEC RX DMA buffers,
which addresses the needs from mx6solox and also works for the other SoCs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch is to add etsec support for LS102xA. First, Little-endian
descriptor mode should be enabled. So RxBDs and TxBDs are interpreted
with little-endian byte ordering. Second, TSEC_SIZE and TSEC_MDIO_OFFSET
are different from PowerPC, redefine them for LS1021xA.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
fsl_enet.h defines the mapping of the usual MII management
registers, which are included in the MDIO register block
common to Freescale ethernet controllers. So it shouldn't
depend on the CPU architecture but it should be actually
part of the arch independent fsl_mdio.h.
To remove the arch dependency, merge the content of
asm/fsl_enet.h into fsl_mdio.h.
Some files (like fm_eth.h) were simply including fsl_enet.h
only for phy.h. These were updated to include phy.h instead.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
There is no reason to redefine pure readl/writel functions.
So remove this redundancy.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Vitaly Andrianov <vitalya@ti.com>
The Broadcom StarFighter2 Ethernet driver is used in multiple Broadcom
SoC(s) and:
- supports multiple MAC blocks,
- provides support for the Broadcom GMAC.
This driver requires MII and PHYLIB.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
We noticed on the DXR2 platform (AM335x with a SMSC LAN9303 switch connected
to the CPSW MAC) that the network performance in U-Boot is quite poor. Only
when the transfer is started without a cable connected, and the cable is
plugged after the first timeout "T" occured, an increased in performance
can be seen. Debugging has revealed, that the cpsw driver has constant
link checking builtin into the rx and tx functions. This results in the
bad performance and seems to be unnecessary. The link has already been
checked in the init function, before the transfer is started. This usually
is sufficient.
BTW: I have seen no other network driver in U-Boot so far, that constantly
checks for link in the rx / tx functions.
The performance numbers on the DXR2 board are:
0.56 MiB/s cpsw_check_link() in rx and tx path
0.87 MiB/s cpsw_check_link() only in tx path
1.0 MiB/s cpsw_check_link() only in rx path
2.7 MiB/s no cpsw_check_link() in rx and tx path
So with this patch the network performance on DXR2 increases from 0.56
to 2.7 MiB/s (nearly 5 times as fast).
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Samuel Egli <samuel.egli@siemens.com>
Tested-by: Heiko Schocher <hs@denx.de>
Cc: Vladimir Koutny <vladimir.koutny@streamunlimited.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement proper support for cache flushing and invalidation into the
Intel e1000 NIC driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
The following configs are not defined at all:
- CONFIG_INCA_IP_SWITCH
- CONFIG_PBL2800_ETHER
- CONFIG_PHY_ICPLUS
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
XFI is supported on T4QDS-XFI board, which removed slot3, and four LANEs
of serdes2 are routed to a SFP+ cages, which to house fiber cable or
direct attach cable(copper), the copper cable is used to emulate the
10GBASE-KR scenario.
So, for XFI usage, there are two scenarios, one will use fiber cable,
another will use copper cable. For fiber cable, there is NO PHY, while
for copper cable, we need to use internal PHY which exist in Serdes to
do auto-negotiation and link training, which implemented in kernel.
We use hwconfig to define cable type for XFI, and fixup dtb based on the
cable type.
For copper cable, set below env in hwconfig:
fsl_10gkr_copper:<10g_mac_name>
the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2. The
four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports,
if a given 10G port will use the copper cable for 10GBASE-KR, set the
<10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be
assumed to be used for the port.
For ex. if four XFI ports will both use copper cable, the hwconfig
should contain:
fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm2_10g1,fm2_10g2
For fiber cable:
1. give PHY address to a XFI port, otherwise, the XFI ports will not be
available in U-boot, there is no PHY physically for XFI when using fiber
cable, this is just to make U-boot happy and we can use the XFI ports
in U-boot.
2. fixup dtb to use fixed-link in case of fiber cable which has no PHY.
Kernel requests that a MAC must have a PHY or fixed-link.
When using XFI protocol, the MAC 9/10 on FM1 should init as 10G interface.
Change serdes 2 protocol 56 to 55 which has same feature as 56 since 56
is not valid any longer.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Messages to afleming@freescale.com now bounce, and should be
directed to my personal address at afleming@gmail.com
Signed-off-by: Andy Fleming <afleming@gmail.com>
R8A7794 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7794.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Some of the fm_port_to_index() callers did not check for -1 return value and
used -1 as an array index.
Signed-off-by: Marian Rotariu <marian.rotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There have been 3 versions of the sunxi_emac support patch during its
development. Somehow version 2 ended up in upstream u-boot where as
the u-boot-sunxi git repo got version 3.
This bumps the version in upstream u-boot to version 3 of the patch:
- Initialize MII clock earlier so mii access to allow independent use
- Name change from WEMAC to EMAC to match mainline kernel & chip manual
- Cosmetic code cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Adding support to load and start the Layerscape Management Complex (MC)
firmware. First, the MC GCR register is set to 0 to reset all cores. MC
firmware and DPL images are copied from their location in NOR flash to
DDR. MC registers are updated with the location of these images.
Deasserting the reset bit of MC GCR register releases core 0 to run.
Core 1 will be released by MC firmware. Stop bits are not touched for
this step. U-boot waits for MC until it boots up. In case of a failure,
device tree is updated accordingly. The MC firmware image uses FIT format.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Add to code to flush the dcache after we writing in DMA buffer.
Also we need invalidate the dcache before we check the status in the
DMA buffer.
Tested in SAMA5D3x-EK with gmac0. Tftp download speed shows in below:
Disable DCache: 1.1 MiB/s
Enable DCache: 1.6 MiB/s
Increase speed with about 40%.
The code should have no impact with the boards which are not
enable_dcache().
Tested in AT91SAM9M10G45EK.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This also renames the CONFIG_SYS_MACB_xx defines. They are used just local and
therefore don't need the CONFIG_SYS_ prefix.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Josh Wu <josh.wu@atmel.com>
'r' of rESR_RTLF is a mistake of E.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R7S72100 of ARM SoC that Renesas manufactured has one Ether port.
This has the same IP SH-Ether. This patch adds support of the R7S72100
in SH-Ether.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
get_phy_id returns -EIO when it can't read from a phy at a given addr. This would cause
create_phy_by_mask to return prematurely before it had tested the other addresses in the provided mask.
Example usage:
Replace
phydev = phy_connect(bus, phy_addr, dev, phy_if)
with
phydev = phy_find_by_mask(bus, phy_mask, phy_if)
if (phydev)
phy_connect_dev(phydev, dev);
Signed-off-by: Cormier, Jonathan <jcormier@criticallink.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
The correct value for this setting can vary across SoCs and boards, so make it
configurable.
Also reduce the default value to 8, which is the same default as used in the
Linux driver.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
On Thu, 2014-05-08 at 22:26 +0100, Ian Campbell wrote:
> The {r,t}xbuffs fields also need to be aligned. Previously this was done
> implicitly because they immediately followed the descriptor tables. Make this
> explicit and also move to the head of the struct.
Looks like I managed to not actually commit the move of the field to the
head of the struct! v3.1 follows....
Ian.
8<------------
>From 2937ba01841887317f6792709ed57cb86b5fc0cd Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Thu, 1 May 2014 19:45:15 +0100
Subject: [PATCH] net/designware: reorder struct dw_eth_dev to pack more
efficiently.
The {tx,rx}_mac_descrtable fields are aligned to ARCH_DMA_MINALIGN, which could
be 256 or even larger. That means there is a potentially huge hole in the
struct before those fields, so move them to the front where they are better
packed.
Moving them to the front also helps ensure that so long as dw_eth_dev is
properly aligned (which it is since "net/designware: ensure device private data
is DMA aligned.") the {tx,rx}_mac_descrtable will be too, or at least avoids
having to worry too much about compiler specifics.
The {r,t}xbuffs fields also need to be aligned. Previously this was done
implicitly because they immediately followed the descriptor tables. Make this
explicit and also move to the head of the struct.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
This is required at least on ARM.
When sending instead of simply invalidating the entire descriptor, flush
as little as possible while still respecting ARCH_DMA_MINALIGN, as
requested by Alexey.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
struct dw_eth_dev contains fields which are accessed via DMA, so make sure it
is aligned to a dma boundary. Without this I see:
ERROR: v7_dcache_inval_range - start address is not aligned - 0x7fb677e0
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch adds support for VSC8664 PHY module which can
be found on Freescale's T4240RDB boards.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The T4080 SoC is a low-power version of the T4160.
T4080 combines 4 dual-threaded Power Architecture e6500
cores with single cluster and two memory complexes.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Current driver uses a Maximum value for MDIO_HOLD when doing 10G MDIO
access, this is due to an errata A-006260 on T4 rev1.0 which is fixed
on rev2.0, so remove the maximum value to use the default value for rev2.0.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
This sets up the linkage from the phydev back to the ethernet device. This
symptom of not doing this which I noticed was:
<NULL> Waiting for PHY auto negotiation to complete....
rather than:
dwmac.1c50000 Waiting for PHY auto negotiation to complete....
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Some functions in include/net.h are ported from
include/linux/etherdevice.h of Linux Kernel.
For ex.
is_zero_ether_addr()
is_multicast_ether_addr()
is_broadcast_ether_addr()
is_valid_ether_addr();
So, we should use the same function name as that of Linux Kernel,
eth_rand_addr(), for consistency.
Besides, eth_rand_addr() has been implemented as an inline function.
So it should not be surrounded by #ifdef CONFIG_RANDOM_MACADDR.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As some PHYs have non-standard PHY ID registers, PHY Id can't
be read correctly by current get_phy_id function, so we enable
get_phy_id redefinable to permit specific PHY driver having own
specific get_phy_id function.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before,
but used "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8035
to enable autonegotiation. Then removed the genphy_config_aneg() function.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Add missing header.
Warnings:
drivers/net/zynq_gem.c:491:5: warning: symbol 'zynq_gem_initialize' was not declared. Should it be static?
drivers/net/zynq_gem.c:542:5: warning: symbol 'zynq_gem_of_init' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ar8031 has the same config steps with ar8021, so change its
config func to ar8021_config instead of genphy_config.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MDIO clock needs to be initialized in u-boot code for SoCs
having FMAN-v3(v3H or v3L) controller due to below reasons
-On SoCs that have FMAN-v3H like B4860, default value of
MDIO_CLK_DIV bits in mdio_stat(mdio_cfg) register generates
mdio clock too high (much higher than 2.5MHz), violating the
IEEE specs.
-On SOCs that have FMAN-v3L like T1040, default value of
MDIO_CLK_DIV bits is zero, so MDIO clock is disabled.
So, for proper functioninig of MDIO, MDIO_CLK_DIV bits needs to
be properly initialized.
Also this type of initialization is generally done in
PBI(pre-bootloader) phase using rcw.But for chips like T1040
which support deep-sleep, such type of initialization cannot be
done in PBI phase due to the limitation that during deep-sleep
resume, FMAN (MDIO) registers are not accessible in PBI phase.
So, mdio clock initailization must be done as part of u-boot.
This initialization code is implemented in memac_phy.c which
gets compiled only for SoCs having FMANv3, so no extra compilation
flag is required.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In the current Datasheet for VSC8514 there is a mistake, saying that
the PHY id is 0x70570. The real value in the identifier registers is
0x70670. Linux PHY driver uses 0x70670 also.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This is dead hardware and no one is interested in making the
necessary changes for upcoming features like generic board or
driver model.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
The ordering of accesses to the rx & tx descriptors is important, yet
the send & recv functions accessed them via regular structure accesses.
This leaves the compiler with the opportunity to reorder those accesses
or to hoist them outside of loops. Prevent that from happening by using
readl & writel to access the descriptors. As a nice bonus, this removes
the need for the driver to care about endianness.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The RX buffers are invalidated when a packet is received, however they
were not suitably cache-line aligned. Allocate them seperately to the
pcnet_priv structure and align to ARCH_DMA_MINALIGN in order to ensure
suitable alignment for the cache invalidation, preventing anything else
being placed in the same lines & lost.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The prior accesses to the descriptor rings & init block via cached
memory had a few issues:
- The memory needs cache flushes or invalidation at the appropriate
times, but was not necessarily aligned on cache line boundaries.
This could lead to data being incorrectly lost or written back to
RAM at the wrong time.
- There are points where ordering of writes to the memory is
important, but because it's cached memory the pcnet controller
would see cache lines written back ordered by address. This could
occasionally lead to hardware seeing descriptors in an incorrect
state.
- Flushing the cache constantly is inefficient.
So, to avoid all of those issues simply access the descriptors & init
block via uncached memory. The MIPS-specific UNCACHED_SDRAM macro is
used to do this (retrieving an address in kseg1) as I could see no
existing generic solution. Since the MIPS Malta board is the only user
of the pcnet driver, hopefully this doesn't matter.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/lubbock/*
- Remove include/configs/lubbock.h
- Cleanup defined(CONFIG_LUBBOCK)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Port configurations are defined in board.c.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
It's important to have ability to flush/invalidate each DMA buffer descriptor
individually to prevent incoherency of adjacent BDs.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
CPSW ia a gigabit device. Use the PHY_GBIT_FEATURES macro to determine phy
supported features.
Tested on cm_t335.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
There was wrong phy_mask for AR8021 device,
so the AR8021 can't be probed correctly.
Changed it from 0x4fffff to 0x4ffff0.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
- Add xilinx_emaclite_of_init to netdev.h
- Remove global data pointer from the driver
- Add better handling for error state.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before
while "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8031/8033
to enable autonegotiation.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch fixes the following warning messages coming out of
'drivers/net/smc91111.h' when compiled for 'vexpress_aemv8a':
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Currently this issue seems to surface when SMSC is compiled for 64-bit
ARMv8 platforms, so the change is protected under CONFIG_ARM64, so that
it doesn't break other existing platforms.
In addition this patch tries to fix some checkpatch errors and warnings
(others related to camel-casing and volatile usage will be addressed
by a later patch).
This fix has been tested on both ARMv8 foundation model v1 and v2.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>
Conflicts:
Makefile
drivers/net/npe/Makefile
These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
Now we are ready to switch over to real Kbuild.
This commit disables temporary scripts:
scripts/{Makefile.build.tmp, Makefile.host.tmp}
and enables real Kbuild scripts:
scripts/{Makefile.build,Makefile.host,Makefile.lib}.
This switch is triggered by the line in scripts/Kbuild.include
-build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build.tmp obj
+build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build obj
We need to adjust some build scripts for U-Boot.
But smaller amount of modification is preferable.
Additionally, we need to fix compiler flags which are
locally added or removed.
In Kbuild, it is not allowed to change CFLAGS locally.
Instead, ccflags-y, asflags-y, cppflags-y,
CFLAGS_$(basetarget).o, CFLAGS_REMOVE_$(basetarget).o
are prepared for that purpose.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
commit 626ee1e3 "phylib: update atheros ar803x phy"
leads in failing ethernet on the pxm2 board.
Calling genphy_config() instead of ar8021_config(),
which seems for ar8021 phys not ar803x phys, make
it working again.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The prescaler value for MDC is calculated wrong for
MX6S. Implement the same logic as linux here which handles
ENET_MAC different then original FEC.
Tested on a custom board with i.MX6S and 100MBit PHY
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Up until now this driver only worked with data cache disabled.
To make it work with enabled data cache following changes were required:
* Flush Tx/Rx buffer descriptors their modification
* Invalidate Tx/Rx buffer descriptors before reading its values
* Flush cache for data passed from CPU to GMAC
* Invalidate cache for data passed from GMAC to CPU
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
* Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
* Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
* Support of custom phy initialization is now done with existing
"board_phy_config".
Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.
For example:
* CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
* CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used
I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Driver "init" function might be called multiple times.
On every "init" Tx/Rx buffer descriptors are initialized: "descs_init"
-> "{tx|rx}_descs_init".
In its turn those init functions set MAC's "{tx|rx}desclistaddr" to
point on the first buffer descriptor in the list.
So CPU to start operation from the first buffer descriptor as well after
every "init" we have to reset "{tx|rx}_currdescnum".
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
EMAC_VLANx regs is not properly initiallized in u-boot, once it's overwrite in the
kernel when DSA enabled, hot reset will lead to bringing up EMAC fail in u-boot.
Signed-off-by: Aaron Wu <Aaron.Wu@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
This driver is no longer used, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
As tsec and fm drivers checking phydev->link
ensure that u-boot don't try access device if link is not ready.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch reverts patch 'add ft_fixup_xgec to support 3rd and 4th 10GEC'.
When dual-role MAC acts as 10G,it still uses fsl,fman-port-1g-rx/tx as before.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
- add more serdes protocols support.
- fix some serdes lanes route.
- fix SGMII doesn't work and incorrect mdio display for XFI when serdes 0x6d.
- correct boot location info for SD/SPI boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As tsec and fm drivers checking phydev->link
ensure that u-boot don't try access device if link is not ready.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.
Conflicts:
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
SH7753 has two fast ethernet controllers and two gigabit ethernet
controllers. It is similar to SH7757.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As mEMAC1 and mEMAC2 are dual-role MACs, which are used as 1G or 10G MAC.
So we update dynamically 'cell-index' to '2' and '3' for 10GEC3 and 10GEC4.
Also change 'fsl,fman-port-1g-rx' to 'fsl,fman-port-10g-rx', ditto for Tx.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
In 48ec5291, only TX path was optimized; this does the same also for RX
path. This results in huge increase of TFTP throughput on custom am3352
board (from 312KiB/s to 1.8MiB/s) and eliminates occasional transfer
timeouts.
Signed-off-by: Vladimir Koutny <vladimir.koutny@streamunlimited.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Tom Rini <trini@ti.com>
Add support for Freescale T2080/T2081 SoC.
T2080 includes the following functions and features:
- Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 mEMACs for network interfaces (four 1Gbps MACs and four 10Gbps/1Gbps MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T2080 and T2081:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
There are more than two 10GEC in single FMAN in some SoCs(e.g. T2080).
This patch adds support for 10GEC3 and 10GEC4.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
This chip is compatible with the existing driver, except that it uses
BAR2 instead of BAR1 for the I/O memory region. Using this patch I can
use the PCIe ethernet interface on the CompuLab Trimslice to boot from
the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276477
Instead of directly calling the low-level invalidate_dcache_range() and
flush_cache() functions, provide thin wrappers that take into account
alignment requirements.
While at it, fix a case where the cache was flushed but should have been
invalidated, two cases where the buffer data was flushed instead of the
descriptor and a missing cache invalidation before reading the packet
data that the NIC just wrote to memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276474
Added d-cache support for zynq_gem.c,
Observed a difference of +0.8 MiB/s when downloading
a file of size of 3007944Bytes.
With d-cache OFF:
----------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
1.3 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
With d-cache ON:
---------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
2.1 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
Changes on zynq_gem for d-cache support:
- Tx and Rx buffers are cache-aligned
- Updated logic for invalidating Rx buffers and flushing Tx buffers.
- Tx and Rx BD's are allocated from non-cacheable region.
(When BDs are cached, we don't see a consistent link)
- Use TX BD status intead of txsr status checks.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When an unprogrammed EEPROM is attached to a dm9000, the dm9000 will
come up with a invalid MAC address of ff:ff:ff:ff:ff:ff. Add code that
gets enabled if CONFIG_RANDOM_MACADDR is enabled that generates a random
(and valid) locally administered MAC address that allows the system to
network boot until a real MAC address can be configured.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
The e1000 driver expects to always have some kind of non-volatile memory
attached directly to the ethernet controller chip. This means that I would
have to add an additional separate flash chip to my custom board just to
store essentially the MAC address. Since I don't want to do that, this patch
introduces a new config option CONFIG_E1000_NO_NVM. If defined it disables
all accesses to the NVM. I have tested the patch with a 82574 controller.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
The masks were ignoring the last 4 bits which didn't allow detection differences
between the ar8031 and ar8035.
Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Patch: 288018
The both AR8031 and AR8035 belong to Atheros 803x serial PHY.
So the phy id mask of AR8031 is the same to the phy id mask
of AR8035. The right mask value is 0x4fffff.
This patch has been tested on the P1010 and P1023.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Patch: 287748
Fix the 32-bit memory access that is not "endianess safe",
i.e. not giving the desired byte layout for LE cpus:
tempval = *((uint *) (tmpbuf + 4)), where 'char tmpbuf[]'.
Free the stack from rendundant local vars:
tmpbuf[] and i.
Use a portable type (u32) for the 32bit tsec register value
holder: tempval.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Use cross arch portable u32 instead of uint for the
tsec registers. Remove the typedefs for the register
struct definitions in the process. Fix long lines.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Currently, the buffer descriptor (BD) fields cannot be
correctly accessed by a little endian processor. This
patch fixes the issue by making the access of BDs to be
portable among different cpu architectures.
Use portable data types for the Rx/Tx buffer descriptor
fields. Use portable I/O accessors to insure that the
big endian BDs are correctly accessed by little endian
cpus too, and to insure proper sync with the H/W.
Removed the redundant RTXBD "volatile" type, as proper
synchronization around BD data accesses is provided by
the I/O accessors now.
The "sparse" tool was also used to verify the correctness
of these changes.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Fix bufPtr and the rxIdx/ txIdx occurrences to
solve the related checkpatch warnings for the
coming patches.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Remove tsec_t typedef. Define macros as getters of
tsec and mdio register memory regions, for consistent
initialization of various 'regs' fields and also to
manage overly long initialization lines.
Use the __iomem address space marker to address sparse
warnings in tsec.c where IO accessors are used, like:
tsec.c:394:19: warning: incorrect type in argument 1 (different
address spaces)
tsec.c:394:19: expected unsigned int volatile [noderef]
<asn:2>*addr
tsec.c:394:19: got unsigned int *<noident>
[...]
Add the __iomem address space marker for the tsec pointers
to struct tsec_mii_mng memory mapped register regions.
This solves the sparse warnings for mixig normal pointers
with __iomem pointers for tsec.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Access to privlist[1] (hardcoded referece to the 2nd tsec's
priv area) is neither correct nor does it make sense in the
current context. Each tsec dev has access to its own priv
instance only, and hence to its own set of group address
registers (GADDR) to filter multicast addresses.
This fix leads to removal of the unused (faulty) privlist[]
and related global static vars. Note that mcast() can be
called only after eth_device allocation and init, and hence
after priv area allocation, so dev->priv is correctly
initialized upon mcast() call.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 278990
There are several implementation issues for tsec_mcast_addr()
addressed by this patch:
* unmanaged, not portable r/w access to registers; fixed with
setbits_be32()/ clrbits_be32()
* use of volatile pointers
* unnecessary forced cast to u8 for the ether_crc() result
* removed redundant parens
* corrected some comment slips
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 279000
This fixes the following compiler warnings when activating
CONFIG_MCAST_TFTP:
tsec.c: In function 'tsec_mcast_addr':
tsec.c:130:2: warning: passing argument 2 of 'ether_crc' makes pointer
from integer without a cast [enabled by default]
In file included from /work/u-boot-net/include/common.h:874:0,
from tsec.c:15:
/work/u-boot-net/include/net.h:189:5: note: expected 'const unsigned
char *' but argument is of type 'u8'
tsec.c: In function 'tsec_initialize':
tsec.c:646:13: warning: assignment from incompatible pointer type
[enabled by default]
eth.c: In function 'eth_mcast_join':
eth.c:358:2: warning: passing argument 2 of 'eth_current->mcast' makes
integer from pointer without a cast [enabled by default]
eth.c:358:2: note: expected 'u32' but argument is of type 'u8 *'
In the eth_mcast_join() implementation, eth_current->mcast()
takes a u8 pointer to the multicast mac address and not a ip
address value as implied by its prototype.
Fix parameter type mismatch for tsec_macst_addr() (tsec.c):
ether_crc() takes a u8 pointer not a u8 value.
mcast() is given a u8 pointer to the multicats mac address.
Update parameter type for the rest of mcast() instances.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 278989
It's important that buffer descriptors are aligned in accordance to GMAC
data bus width (32/64/128-bit). It's safe to align to 128-bit (16-bytes)
for every bus width type.
If buffer descriptor is improperly aligned GMAC discards lower bits of
provided address and as a result reads from improper location that
doesn't match expected fields.
Commit ef76025a99 "net: Multiple
updates/enhancements to designware.c" introduced another structure
member "link_printed" right before buffer descriptors while "padding"
member was left untouched. This together with alignment of structure
itself to 16-byte boundary forces buffer descriptoprs always to be
4-byte aligned that causes driver complete disfunction if GMAC bus width
is 64 or 128-bit.
Proposed change makes sure all buffer descriptors are 16-byte (128-bit)
aligned.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Patch: 277902
"bus mode" register contains lots of fields and some of them don't
expect to be written with 0 (zero). So since we're only interested in
resetting MAC (which is done with setting the least significant bit of
this register with "0") I believe it's better to modify only 1 bit of
the register.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Vipin Kumar <vipin.kumar@st.com>
Patch: 277864
R8A7791 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7791.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Joe Hershberger <joe.hershberger@gmail.com>
AR8035 driver will be never applied because of wrong mask for
AR8031 driver. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Pavel Nakonechny <pavel.nakonechny@skitlab.ru>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Patch: 276944
This chip is compatible with other RTL8168 chips and can be found on the
NVIDIA Cardhu and Beaver boards.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276475
currticks() is defined as get_timer(0), which returns an unsigned long,
so use %lu instead of %d to print the result.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276473
The 'get_phy_driver' code in 'drivers/net/phy/phy.c' uses the following
method to determine which driver is to be loaded for a particular PHY
module:
list_for_each(entry, &phy_drivers) {
drv = list_entry(entry, struct phy_driver, list);
if ((drv->uid & drv->mask) == (phy_id & drv->mask))
return drv;
}
This means that a drv->mask of 0xfffff0 will return incorrect phy driver
for the logic above, even if the drv->uid is anything other than
something ending with a 0x0.
For e.g. if the RTL8211E drv->uid is 0x1cc915 and drv->mask is 0xffffff
and the RTL8211B drv->uid is 0x1cc910 and drv->mask is 0xffffff0, then
the phy driver selected will always be RTL8211B even though the
underlying phy connected on the board is a 8211E module.
This patch fixes this issue.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
This patch adds support for VSC8514 PHY module which can be
found on Freescale's T1040RDB boards.
Signed-off-by: Arpit Goel <B44344@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
R8A7790 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7790.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The sh-eth of rmobile needs to use invalidate_cache* function.
This patch adds invalidate_cache* function.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Patch: 268948
sh-eth can change the alignment size of a packet descriptor according to BUS
size. This patch adds this function.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The cache API of SH was changed from dcache_wback_range to flush_dcache_range.
sh-eth uses dcache_wback_range. This patch changes to flush_dcache_range.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Avoid a recently introduced unused variable warning for boards that
use mvgbe but not phylib.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Patch: 266334
As AR8031 and AR8033 have same PHY ID 0x4dd074, they use the
common driver. Currently AR8031_driver didn't work for AR8033,
hence updated it to have it work on AR8031/AR8033.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
The fec_halt() never free'd both RX and TX DMA descriptors that
were allocated in fec_init(), nor did it free the RX buffers.
Rework the FEC driver so that these descriptors and buffers are
allocated only once in fec_probe().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
T1040 Soc has four personalities:
-T1040 (4 cores with L2 switch)
-T1042:Reduced personality of T1040 without L2 switch
-T1020:Reduced personality of T1040 with less cores(2 cores)
-T1022:Reduced personality of T1040 with 2 cores and without L2 switch
Update defines in arch/powerpc header files, Makefiles and in
driver/net/fm/Makefile to support all T1040 personalities
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: fixed Makefiles]
Acked-by: York Sun <yorksun@freescale.com>
The MPC824x processors have long reached EOL, and the PN62 board has
not seen any board-specific updates for more than a decade. It is now
causing build issues. Instead of wasting time on things nobody is
interested in any more, we rather drop this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
cc: Tom Rini <trini@ti.com>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
On relatively slow boards (such as the MIPS Malta with an FPGA core
card) it can be extremely common for transmits to underflow - to the
point where it appears they simply do not work at all. Setting the
NOUFLO bit causes the ethernet controller to not begin transmission on
the wire until a transmit start point is reached. Setting that transmit
start point to the full packet will cause the controller to only
transmit the packet once it has buffered it entirely thus preventing any
transmit underflows from occuring and allowing the controller to
function on slower boards.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Ensure that the view of memory from the CPU & the ethernet controller is
coherent at the various points where they exchange data. This prevents
stale data from being transmitted or received, and prevents the driver
from getting stuck waiting for the ethernet controller to update
descriptors when in reality it has but the old values are being read
from cache.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fix up the code to match Documentation/CodingStyle. This is mostly
removing extraneous spaces.
No functional change is intended.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Netconsole loses the second character when used as input by
either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX
Before a nc_send_packet() to echo the input, a check is done to see if
nc_ether is valid. If its not, it waits for an arp request and then sends
the packet (which contains the first character of line to be displayed as
output). As part of reaping the arp request, the second character is consumed.
We protect this by making the call to NetLoop(NETCONS) between
input_recursion.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Get DMA bus width from design config register
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This can be useful if one wants to disable an interface in u-boot
because u-boot should not manage it but then later reenable it for FDT
fixing or if the kernel uses this interface.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix conflict in fm_eth.h]
Acked-by: York Sun <yorksun@freescale.com>
T1040QDS is a high-performance computing evaluation, development and
test platform supporting the T1040 QorIQ Power Architecture™ processor.
T1040QDS board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch
- Four 1 Gbps Ethernet controllers
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: fix conflict in boards.cfg]
Acked-by-by: York Sun <yorksun@freescale.com>
Fix PHY addresses for QSGMII Riser Card working in
SGMII mode on board P3041/P5020/P4080/P5040/B4860.
QSGMII Riser Card can work in SGMII mode, but
having the different PHY addresses.
So the following steps should be done:
1. Confirm whether QSGMII Riser Card is used.
2. If yes, set the proper PHY address.
Generally, the function is_qsgmii_riser_card() is
for step 1, and set_sgmii_phy() for step 2.
However, there are still some special situations,
take P5040 and B4860 as examples, the PHY addresses
need to be changed when serdes protocol is changed,
so it is necessary to confirm the protocol before
setting PHY addresses.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
if phy_connect() did not find a phy, phydev is NULL and
following code in cpsw_phy_init() crashes. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Performing tftp transfers on mx28 results in random timeouts.
Hector Palacios and Robert Hodaszi analyzed the root cause being related to the
wrong alignment of the 'buff' buffer inside fec_recv().
Benoît Thébaudeau provided an excellent analysis of the alignment bug that is
present on older versions, such as GCC 4.5.4:
http://marc.info/?l=u-boot&m=137942904906131&w=2
Use ALLOC_CACHE_ALIGN_BUFFER() to avoid alignment issues from older GCC
versions.
Reported-by: Hector Palacios <hector.palacios@digi.com>
Tested-by: Oliver Metz <oliver@freetz.org>
Tested-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Similarly as mx25 and mx53, mx6solo-lite needs to setup the MII gasket for RMII
mode.
Add support for mx6solo-lite.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license. However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word. I'd prefer
to be consistent to this end".
Change the license IDs to use the official name.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix various misspellings of things like "environment", "kernel",
"default" and "volatile", and throw in a couple grammar fixes.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
fix the following building warning
---8>---
macb.c: In function 'macb_init':
macb.c:400:14: warning: 'phydev' may be used uninitialized in this function
macb.c:377:21: note: 'phydev' was declared here
---<8---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Without this change, the following message is generated:
Warning: FEC using MAC address from net device
See doc/README.enetaddr for details.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
1. Reformat tx/rx descriptor as an uniform struct.
2. Replace uint32_t[2] with uint64_t for descriptor control.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
This patch adds support for Realtek PHY modules RTL8211DN and
RTL8211E (variants: RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211EG-VB-CG),
which can be found on Freescale's T1040RDB boards.
To make the driver more generic across 8211 family, a generic name 8211x
is added for macros and function names.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Use ARRAY_SIZE instead of having similar implementation in each drivers.
The NUMELEMS defined in drivers/net/npe/include/IxOsalTypes.h is not used
at all, so this patch removes it instead of converting it to use ARRAY_SIZE.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.
Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h
Signed-off-by: Tom Rini <trini@ti.com>
FMAN firmware can be in NOR flash, NAND flash, SPI flash, MMC or even
remote. In case none of them is defined, set it to null.
Signed-off-by: York Sun <yorksun@freescale.com>
accessing a lan9303 switch with the cpsw driver results in wrong
speed detection, as the switch sets the BMSR_ERCAP in BMSR
register, and follow read of the MII_STAT1000 register fails, as
the switch does not support it. Current code did not check,
if a phy_read() fails ... fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
BD ram address may vary in various SOC, so removing the hardcoding and
passing the same information through platform data
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
There is no reason to wait for the entire frame to start DMA on receive,
so enable rx cut-thru for better performance.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The pcnet driver uses the pci_phys_to_mem function
to get the memory address of the DMA buffers. This
This assumes an 1:1 mapping between the PCI and
physical memory which is not true on all platforms.
On MIPS platform U-Boot is running within a mapped
memory region, and the pci_phys_to_mem macro can't
be used to obtain the memory address of the buffers.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Commit de1d786e (add support for Xilinx 1000BASE-X phy (GTX)) introduced the
checking for ESTATUS_1000_XHALF, but it incorrectly sets the
SUPPORTED_1000baseX_Full flag in this case.
Set the SUPPORTED_1000baseX_Half flag instead.
Acked-by: Charles Coldwell <coldwell@gmail.com>
Reviewed-By: Sascha Silbe <t-uboot@infra-silbe.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
de1d786 [add support for Xilinx 1000BASE-X phy (GTX)] introduced a
check for the extended status register in order to support
1Gbps-capable PHYs that don't have the 1000BASE-T registers. Since
Extended Status only indicates what the PHY (i.e. the local side) is
capable of, this broke communication with non-1Gbps peers.
Only check the extended status if the 1000BASE-T registers are
actually missing so we don't end up setting speed to 1Gbps even though
the previous test (for the combination of local and peer support for
1Gbps) already indicated we can't do 1Gbps with the current peer.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
The MX28 multi-layer AHB bus can be too slow and trigger the
FEC DMA too early, before all the data hit the DRAM. This patch
ensures the data are written in the RAM before the DMA starts.
Please see the comment in the patch for full details.
This patch was produced with an amazing help from Albert Aribaud,
who pointed out it can possibly be such a bus synchronisation
issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Remove incorrectly called and duplicate flush_dcache_range() call
from fec_mxc driver. The call is not needed, since the caches are
already flushed in fec_tbd_init(), moreover the second argument should
be the ending address, not size.
Signed-off-by: Marek Vasut <marex@denx.de>
Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
add atheros ar803x phy, used on the upcoming siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
add natsemi dp83630 phy, used on the upcoming siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Using CONFIG_AT91FAMILY replace #ifdeferry for atmel SoC
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
The device interface is 16 bits wide.
All the available packets are read from the incoming fifo.
Signed-off-by: Roberto Cerati <roberto.cerati@bticino.it>
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
[voice.shen@atmel.com: address comments from review results]
[voice.shen@atmel.com: clean up for submit]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
commit 39695029bc15041c809df3db4ba19bd729c447fa
Author: Charles Coldwell <coldwell@ll.mit.edu>
Date: Tue Feb 19 08:27:33 2013 -0500
Changes to support the Xilinx 1000BASE-X phy (GTX/MGT)
Signed-off-by: Charles Coldwell <coldwell@ll.mit.edu>
Add support for Micrel PHY KSZ9031 in phylib,
including small rework for KSZ9021 to avoid
code duplication
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Joe Herschberger <joe.hershberger@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
SPEAr310 and SPEAr320 Ethernet interfaces share same MDIO lines to control their
respective phys. Currently there is a fixed configuration in which only a
particular MAC can use the MDIO lines.
Call an arch specific function to take control of specific mdio lines at
runtime.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Marvell Dove also uses mvgbe as ethernet driver, therefore add support
for Dove to reuse the current driver.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch adds support for the WEMAC, the ethernet controller included
in the Allwinner A10 SoC. It will get used in the upcoming A10 board
support.
From: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
This patch adds FEC support for Vybrid VF610 platform.
In function fec_open(), RCR register is only set as RGMII mode. But RCR
register should be set as RMII mode for VF610 platform.
This configuration is already done in fec_reg_setup(), so this piece of
code could just leave untouched the FEC_RCNTRL_RGMII / FEC_RCNTRL_RMII /
FEC_RCNTRL_MII_MODE bits.
Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoit Thebaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
- Added SERDES2 PRTCLs = 0x98, 0x9E
- Default Phy Addresses for Teranetics PHY on XAUI card
The PHY addresses of Teranetics PHY on XAUI riser card are assigned
based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on
AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1
and slot2
- Configure MDIO for 10Gig Mac
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
TN80xx has same PHY ID as TN2020, but it needs different setting to register
30.93 which used to select line, so we read register 30.32 which has
bit 15:12 to indicate PHY hardware version, for TN20xx we will get 3 or 2,
for TN80xx we will get 5 or 4.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The VSC8574 is a quad-port Gigabit Ethernet transceiver with four SerDes
interfaces for quad-port dual media capability. This driver supports SGMII
and QSGMII MAC mode. For now SGMII mode is tested.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
- set proper compatible property name for mEMAC.
- fixed ft_fixup_port for dual-role mEMAC, which will lead to
MAC node disabled incorrectly.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4160 SoC is low power version of T4240. The T4160 combines eight dual
threaded Power Architecture e6500 cores and two memory complexes (CoreNet
platform cache and DDR3 memory controller) with the same high-performance
datapath acceleration, networking, and peripheral bus interfaces.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. fix 10G mac offset by plus 8;
2. add second 10G port info for FM1 & FM2 when init ethernet info;
3. fix 10G lanes name to match lane protocol table;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Adds an ET1011C PHY driver which is derived from the
Linux kernel PHY driver (drivers/net/phy/et1011c.c)
from the v3.9-rc2 tag. Note that an errata workaround
config option is implemented to allow for TX_CLK to be
enabled even when gigabit mode is negotiated. This
workaround is used on the PG1.0 TI814X EVM.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
TI814x's version 1 CPSW has a different slave_regs layout.
Add support for the differing registers.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Some legacy RGMII phys don't have in band signaling for the
speed information. so set the RGMII MAC mode according to
the speed got from PHY.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reported-by: John Traill <john.traill@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Avoid overwriting GEMx_RCLK_CTRL and GEMx_CLK_CTRL
if the Ethernet interface is connect on EMIO
Do not enable emio for this standard board configuration for now.
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Pass the PHY address to the driver init to
allow parallel use of both interfaces
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
The whole driver used 100Mbps because of zc702 rev B.
Fix problem with not setup proper clock for gem1.
This is generic approach for clk setup.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
BDs can be correctly setup just once and init function
performs only phy autodetection and enabling RX/TX.
RX/TX are disabled in halt function.
This patch solves the problem with repeatable tftp transfers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Removing this bit causes that frame is sent only once.
(With wrap big one packet has been sent several times
which dramatically decrease throughput)
TRM: (Table 16-3: Tx Buffer Descriptor Entry)
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
This phy is used on zedboard (xilinx zynq platform).
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
- In arch/arm/cpu/armv7/omap-common/timer.c,
drivers/mtd/nand/omap_gpmc.c and drivers/net/cpsw.c add #include files
that the driver needs but had been relying on <config.h> to bring in.
- In arch/arm/cpu/armv7/omap-common/lowlevel_init.S add <config.h>
- In am335x_evm.h and pcm051.h don't globally include
<asm/arch/hardware.h> and <asm/arch/cpu.h> but just <asm/arch/omap.h>
as that is the only include which defines things the config uses.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these
conflicts manually and comment the #else/#endif lines for clarity.
Conflicts:
arch/arm/include/asm/arch-davinci/gpio.h
drivers/gpio/da8xx_gpio.c
Signed-off-by: Tom Rini <trini@ti.com>
Before submitting packets to cpdma, phy status is updated on every packet
which leads to delay in packet send intern reduces the Ethernet performance.
Checking mdio status for each packet will reduce timetaken to send a packet
and there by increasing the Ethernet performance. With this the performance
is increased from 208KiB/s to 375KiB/s on EVMsk
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
It is useful to be able to try a range of
possible phy addresses to connect.
Also, an ethernet device is not required
to use phy_find_by_mask leading to better
separation of mii vs ethernet, as suggested
by Andy Fleming.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Only the hardware ethernet registers are needed
for this function, so don't pass the more general
structure. I'm trying to separate MII and fec.
This also fixes MX28 fec_mii_setspeed use on secondary ethernet port
This was found by inspection of the code and should be
checked on real hardware.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
It is more logical to test for CONFIG_FEC_MXC_PHYADDR
to determine whether to define the function fecmxc_initialize.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
SH7752 has two fast ethernet controllers and two gigabit ethernet
controllers. It is similar to SH7757.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marvell 88E1118R has different uid then 88E1118.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Andy Fleming <afleming@freescale.com>
CC: Zang Roy-R61911 <tie-fei.zang@freescale.com>
CC: Kumar Gala <galak@kernel.crashing.org>
In e1000e driver, Rx descriptor queue is used such that hardware can add only
one descriptor at a time. So the WTHRESH granularity in RXDCTL should be set
to single descriptor. This would ensure that every time controller fills a Rx
descriptor, it is flushed to host memory. Earlier this granularity was in
cache line units i.e 2 descriptors. This leads to controller always waiting
for 2 descriptors before flushing them out. But since not more than one Rx BD
is actually available , the accumulation condition never gets hit.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Vakul Garg <vakul@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of
P3041DS/P5020DS ("Hydra") reference board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
phy.c:46:5: warning: symbol 'genphy_config_advert' was not declared. Should it be static?
phy.c:121:5: warning: symbol 'genphy_setup_forced' was not declared. Should it be static?
phy.c:468:5: warning: symbol 'phy_probe' was not declared. Should it be static?
phy.c:491:19: warning: symbol 'get_phy_driver' was not declared. Should it be static?
phy.c:508:19: warning: symbol 'phy_device_create' was not declared. Should it be static?
phy.c:552:5: warning: symbol 'get_phy_id' was not declared. Should it be static?
phy.c:584:19: warning: symbol 'get_phy_device' was not declared. Should it be sta
vitesse.c:126:5: warning: symbol 'vsc8601_config' was not declared. Should it be static?
vsc7385.c:33:5: warning: symbol 'vsc7385_upload_firmware' was not declared. Should it be static?
tgec_phy.c:33:5: warning: symbol 'tgec_mdio_write' was not declared. Should it be static?
tgec_phy.c:75:5: warning: symbol 'tgec_mdio_read' was not declared. Should it be static?
tgec_phy.c:117:5: warning: symbol 'tgec_mdio_reset' was not declared. Should it be static?
eth.c:48:6: warning: symbol 'dtsec_configure_serdes' was not declared. Should it be static?
p4080.c:26:5: warning: symbol 'port_to_devdisr' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
bootp.c:44:14: warning: symbol 'dhcp_state' was not declared. Should it be static?
bootp.c:45:15: warning: symbol 'dhcp_leasetime' was not declared. Should it be static?
bootp.c:46:10: warning: symbol 'NetDHCPServerIP' was not declared. Should it be static?
arp.c:30:17: warning: symbol 'NetArpWaitReplyIP' was not declared. Should it be static?
arp.c:37:16: warning: symbol 'NetArpTxPacket' was not declared. Should it be static?
arp.c:38:17: warning: symbol 'NetArpPacketBuf' was not declared. Should it be static?
atheros.c:33:19: warning: symbol 'AR8021_driver' was not declared. Should it be static?
net.c:183:7: warning: symbol 'PktBuf' was not declared. Should it be static?
net.c:159:21: warning: symbol 'net_state' was not declared. Should it be static?
ping.c:73:6: warning: symbol 'ping_start' was not declared. Should it be static?
ping.c:82:13: warning: symbol 'ping_receive' was not declared. Should it be static?
tftp.c:53:7: warning: symbol 'TftpRRQTimeoutMSecs' was not declared. Should it be static?
tftp.c:54:5: warning: symbol 'TftpRRQTimeoutCountMax' was not declared. Should it be static?
eth.c:125:19: warning: symbol 'eth_current' was not declared. Should it be static?
Note: in the ping.c fix, commit a36b12f95a
"net: Move PING out of net.c" mistakenly carried the ifdef CMD_PING
clause from when it was necessary to avoid warnings when it was embedded
in net.c.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
u-boot's byteorder headers did not contain endianness attributions
for use with sparse, causing a lot of false positives. Import the
kernel's latest definitions, and enable them by including compiler.h
and types.h. They come with 'const' added for some swab functions, so
fix those up, too:
include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default]
Also, note: u-boot's historic __BYTE_ORDER definition has been
preserved (for the time being at least).
We also remove ad-hoc barrier() definitions, since we're including
compiler.h in files that hadn't in the past:
macb.c:54:0: warning: "barrier" redefined [enabled by default]
In addition, including compiler.h in byteorder changes the 'noinline'
definition to expand to __attribute__((noinline)). This fixes
arch/powerpc/lib/bootm.c:
bootm.c:329:16: error: attribute '__attribute__': unknown attribute
bootm.c:329:16: error: expected ')' before '__attribute__'
bootm.c:329:25: error: expected identifier or '(' before ')' token
powerpc sparse builds yield:
include/common.h:356:22: error: marked inline, but without a definition
the unknown-reason inlining without a definition is considered obsolete
given it was part of the 2002 initial commit, and no arm version was
'fixed.'
also fixed:
ydirectenv.h:60:0: warning: "inline" redefined [enabled by default]
and:
Configuring for devconcenter - Board: intip, Options: DEVCONCENTER
make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1
make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2
powerpc-fsl-linux-size: './u-boot': No such file
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available
4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here
and:
In file included from crc32.c:50:0:
crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration]
crc32table.h:4:1: error: initializer element is not constant
crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]')
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[trini: Remove '#endif' in include/common.h around setenv portion]
Signed-off-by: Tom Rini <trini@ti.com>
TBI PHY address (TBIPA) register is set in general frame manager
phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c, and
it is supposed to set TBIPA on FM1@DTSEC1 in case of FM1@DTSEC1
isn't used directly, which provides MDIO for other ports. So
following code is wrong in case of FM2, which has a different
mac base.
struct dtsec *regs = (struct dtsec *)fm_eth->mac->base;
/* Assign a Physical address to the TBI */
out_be32(®s->tbipa, CONFIG_SYS_TBIPA_VALUE);
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The multirate ethernet media access controller (mEMAC) interfaces to
10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII
interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Freescale B4860 and variant SoCs. Features of B4860 are
(incomplete list):
Six fully-programmable StarCore SC3900 FVP subsystems, divided into three
clusters-each core runs up to 1.2 GHz, with an architecture highly
optimized for wireless base station applications
Four dual-thread e6500 Power Architecture processors organized in one
cluster-each core runs up to 1.8 GHz
Two DDR3/3L controllers for high-speed, industry-standard memory interface
each runs at up to 1866.67 MHz
MAPLE-B3 hardware acceleration-for forward error correction schemes
including Turbo or Viterbi decoding, Turbo encoding and rate matching,
MIMO MMSE equalization scheme, matrix operations, CRC insertion and
check, DFT/iDFT and FFT/iFFT calculations, PUSCH/PDSCH acceleration,
and UMTS chip rate acceleration
CoreNet fabric that fully supports coherency using MESI protocol between
the e6500 cores, SC3900 FVP cores, memories and external interfaces.
CoreNet fabric interconnect runs at 667 MHz and supports coherent and
non-coherent out of order transactions with prioritization and
bandwidth allocation amongst CoreNet endpoints.
Data Path Acceleration Architecture, which includes the following:
Frame Manager (FMan), which supports in-line packet parsing and general
classification to enable policing and QoS-based packet distribution
Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading
of queue management, task management, load distribution, flow ordering,
buffer management, and allocation tasks from the cores
Security engine (SEC 5.3)-crypto-acceleration for protocols such as
IPsec, SSL, and 802.16
RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and
outbound). Supports types 5, 6 (outbound only)
Large internal cache memory with snooping and stashing capabilities for
bandwidth saving and high utilization of processor elements. The
9856-Kbyte internal memory space includes the following:
32 Kbyte L1 ICache per e6500/SC3900 core
32 Kbyte L1 DCache per e6500/SC3900 core
2048 Kbyte unified L2 cache for each SC3900 FVP cluster
2048 Kbyte unified L2 cache for the e6500 cluster
Two 512 Kbyte shared L3 CoreNet platform caches (CPC)
Sixteen 10-GHz SerDes lanes serving:
Two Serial RapidIO interfaces. Each supports up to 4 lanes and a total
of up to 8 lanes
Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue-
less antenna connection
Two 10-Gbit Ethernet controllers (10GEC)
Six 1G/2.5-Gbit Ethernet controllers for network communications
PCI Express controller
Debug (Aurora)
Two OCeaN DMAs
Various system peripherals
182 32-bit timers
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Freescale T4240 SoC. Feature of T4240 are
(incomplete list):
12 dual-threaded e6500 cores built on Power Architecture® technology
Arranged as clusters of four cores sharing a 2 MB L2 cache.
Up to 1.8 GHz at 1.0 V with 64-bit ISA support (Power Architecture
v2.06-compliant)
Three levels of instruction: user, supervisor, and hypervisor
1.5 MB CoreNet Platform Cache (CPC)
Hierarchical interconnect fabric
CoreNet fabric supporting coherent and non-coherent transactions with
prioritization and bandwidth allocation amongst CoreNet end-points
1.6 Tbps coherent read bandwidth
Queue Manager (QMan) fabric supporting packet-level queue management and
quality of service scheduling
Three 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support
Memory prefetch engine (PMan)
Data Path Acceleration Architecture (DPAA) incorporating acceleration for
the following functions:
Packet parsing, classification, and distribution (Frame Manager 1.1)
Queue management for scheduling, packet sequencing, and congestion
management (Queue Manager 1.1)
Hardware buffer management for buffer allocation and de-allocation
(BMan 1.1)
Cryptography acceleration (SEC 5.0) at up to 40 Gbps
RegEx Pattern Matching Acceleration (PME 2.1) at up to 10 Gbps
Decompression/Compression Acceleration (DCE 1.0) at up to 20 Gbps
DPAA chip-to-chip interconnect via RapidIO Message Manager (RMAN 1.0)
32 SerDes lanes at up to 10.3125 GHz
Ethernet interfaces
Up to four 10 Gbps Ethernet MACs
Up to sixteen 1 Gbps Ethernet MACs
Maximum configuration of 4 x 10 GE + 8 x 1 GE
High-speed peripheral interfaces
Four PCI Express 2.0/3.0 controllers
Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz with
Type 11 messaging and Type 9 data streaming support
Interlaken look-aside interface for serial TCAM connection
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Four I2C controllers
Four 2-pin or two 4-pin UARTs
Integrated Flash controller supporting NAND and NOR flash
Two eight-channel DMA engines
Support for hardware virtualization and partitioning enforcement
QorIQ Platform's Trust Architecture 1.1
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The following warning was produced, fix it:
mcfmii.c: In function 'mcffec_miiphy_write':
mcfmii.c:318:8: warning: variable 'rdreg' set but not used [-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: "Jin Zhengxiong-R64188" <R64188@freescale.com>
Cc: Jason Jin <jason.jin@freescale.com>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>
The mechanism waiting for transmission to finish in fec_send() now
relies on the E-bit being cleared in the TX buffer descriptor. In
case of data cache being on, this means invalidation of data cache
above this TX buffer descriptor on each test for the E-bit being
cleared.
Apparently, there is another way to check if the transmission did
complete. This is by checking the TDAR bit in the X_DES_ACTIVE
register. Reading a register does not need any data cache invalidation,
which is beneficial.
Rework the sequence that wait for completion of the transmission so that
the TDAR bit is tested first and afterwards check the E-bit being clear.
This cuts down the number of cache invalidation calls to one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The FEC hardware sometimes errors out on data transfer and hangs in
the tightloop adjusted by this patch. So add timeout into the tightloop
to make such a hang recoverable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Align the address that's to be invalidated/flushed properly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advans>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Do not pass unaligned RX buffer to the upper layers. The upper layer,
especially in the ARP case, recycles the buffer and passes it back into
the FEC, into it's TX path. With caches enabled, the FEC hangs on this
from time to time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advans>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
-VSC8662 is Dual Port 10/100/1000Base-T Phy,
100Base-FX/1000/Base-X Gigabit Ethernt Transceiver Phy.
-Its register set and features are similar to
other Vitesse Phys
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This patch add support for the configuration of an external switch from
the 88E6xxx series from Marvell trough an MDIO link using indirect
adressing. This can be used if we do not want to use an EEPROM for the
configuration.
This driver is not generic and was not tested on other switches than the
88e6352. This is proposed as a first implementation that is somewhat
limited but works and that can be used as a basis for further
developments for this switch family.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Device driver for Zynq Gem IP.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Check the incoming packets' source IP address... if ncip isn't set to a
broadcast address, only listen to the client at ncip.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Refresh the netconsole settings from the env before each packet instead
of only on netconsole init.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Previously u-boot would initialize the network interface for every
network operation and then shut it down again. This makes sense for
most operations where the network in not known to be needed soon after
the operation is complete. In the case of netconsole, it will use the
network for every interaction with the shell or every printf. This
means that the network is being reinitialized very often. On many
devices, this intialization is very slow.
This patch checks for consecutive netconsole actions and leaves the
ethernet hardware initialized between them. It will still behave the
same old way for all other network operations and any time another
network operation happens between netconsole operations.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Allow a board to configure a larger buffer for netconsole, but leave
the default.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
R8A7740 of rmobile has ethernet device, and this is same IP of
sh-ether. This support R8A7740 of rmobile.
Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Apply the following questionable adjustment to silence GCC.
armada100_fec.c: In function ‘armdfec_send’:
armada100_fec.c:589:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Support new CONFIG_OF_CONTROL option where device
probing is done based on device tree description.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
It is desirable to use different port numbers for sending and receiving
packets with netconsole in the case where you have more than one device
on the local subnet with netconsole enabled for broadcast. When they
use the same port for both, any output from one will look like input to
the other. This is typlically not desirable.
This patch allows the input and output ports to be specified separately
in the environment.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
greth.c: In function ‘greth_recv’:
greth.c:507:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’ [-Wformat]
greth.c:507:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘unsigned int’ [-Wformat]
greth.c:541:6: warning: pointer targets in assignment differ in signedness [-Wpointer-sign]
greth.c: In function ‘greth_initialize’:
greth.c:623:2: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
greth.c:655:3: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
greth.c:684:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: u-boot-dm@lists.denx.de
* 'master' of git://git.denx.de/u-boot-avr32:
net:macb: add line break
avr32:portmux: fix setup for macb1
avr32: Remove redundant LDSCRIPT definition
Signed-off-by: Wolfgang Denk <wd@denx.de>
Without this patch we see annoying output like this:
---8<---
U-Boot> dhcp
macb1: PHY not foundmacb0: PHY present at 1
macb0: Starting autonegotiation...
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Add at91sam9x5ek board support, this board support the following SoCs
AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35
Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
CPSW is an on-chip ethernet switch that is found on various SoCs from Texas
Instruments. This patch adds a simple driver (based on the Linux driver) for
this hardware module.
This patch also adds support to clean and flush dcache during packet send
and receive.
Changes by Sandhya: Added support to clean and flush dcache during packet
send/receive and added timeouts.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
[Ilya: Cleaned cache handling, some style cleanup, some small
fixes, use of internal RAM for descriptors]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
These are not supported as individual build targets, but instead
are supported by another target.
The dead p4040 defines in particular had bitrotted significantly.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We have a dedicated function for setting the node status now, so use it.
Also improve a comment and fix the type of the phandle variable.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Function fm_info_get_phy_address() returns the PHY address for a given
Fman port. This is handy when the MDIO code needs to fixup the Ethernet
nodes in the device tree to point to PHY nodes for a specific PHY address.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Unlike previous SOCs, the Freescale P5040 has a fifth DTSEC on the second
Fman, so add the Fman and SerDes macros for that DTSEC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
* 'next' of git://git.denx.de/u-boot:
MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
doc: cleanup - move board READMEs into respective board directories
net: sh_eth: add support for SH7757's GETHER
net: sh_eth: modify the definitions of regsiter
net: sh_eth: add SH_ETH_TYPE_ condition
net: sh_eth: clean up for the SH7757's code
net: fec_mxc: Fix MDC for xMII
net: fec_mxc: Fix setting of RCR for xMII
net: nfs: make NFS_TIMEOUT configurable
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
SH7757 has 2 ETHERs and 2 GETHERs. This patch supports the SH7757's
GETHER. If CONFIG_SH_ETHER_USE_GETHER is defined using SH7757,
the driver handles the GETHER.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The previous code had many similar definitions in each CPU.
This patch borrows from the sh_eth driver of Linux kernel.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
At the moment, the driver supports the following CPUs:
- GETHER (Gigabit Ethernet) : SH7763, SH7734
- ETHER (Fast Ethernet) : SH7724, SH7757
And the driver had the following "#if":
#if defined(CONFIG_CPU_SH7763) || defined(CONFIG_CPU_SH7734)
#if !defined(CONFIG_CPU_SH7757) && !defined(CONFIG_CPU_SH7724)
- Those are for GETHER
#if defined(CONFIG_CPU_SH7724) || defined(CONFIG_CPU_SH7757)
- This is for ETHER
So, for clean up the code, this patch adds SH_ETH_TYPE_GETHER and
SH_ETH_TYPE_ETHER. And then, the patch modifies the above "#if".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The SH7757's ETHER can work using the SH7724's setting. So, the patch
modifies it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The MDC signal is available on all xMII (i.e. 'not 7-wire') interfaces, so
mii_speed has to be set for all these interfaces, and not only for MII.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
At least on i.MX25, the RMII mode did not work, which is fixed by this patch.
The MII_MODE bit of the FEC RCR register means xMII, i.e. 'not 7-wire', so set
it accordingly.
According to the xMII and 7-wire (aka GPSI) standards, full duplex should be
available on xMII, but not on 7-wire, so set FCE accordingly. The FEC may
support full duplex for 7-wire too, but the reference manual does not say that,
so avoid an invalid assumption. Actually, the choice between half and full
duplex also depends on the endpoint/switch/repeater configuration, so a config
option could be added for that, but there has been no need for it so far.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Now that common code doesn't declare these as volatile, we don't need to
either anymore. This fixes the build warning:
bfin_mac.c: In function 'bfin_EMAC_recv':
bfin_mac.c:193:23: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'next' of git://git.denx.de/u-boot-net:
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
This commit is an add-on to f6c4191f. There are a few registers where
consecutive writes to the same location should be avoided or have a delay.
According to Synopsys, here is a list of the registers and bit(s) where
consecutive writes should be avoided or a delay is required:
DMA Registers:
Register 0 Bit 7
Register 6 All bits except for 24, 16-13, 2-1.
GMAC Registers:
Registers 0-3 All bits
Registers 6-7 All bits
Register 10 All bits
Register 11 All bits except for 5-6.
Registers 16-47 All bits
Register 48 All bits except for 18-16, 14.
Register 448 Bit 4.
Register 459 Bits 0-3.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Reviewed-by: Matthew Gerlach <mgerlach@altera.com>
Acked-by: Amit Virdi <amit.virdi@st.com>
Micrel accidentally used the same part number
for the KS8721 and KSZ9021. So, both cannot be
in the same build of u-boot. Add a config option
to handle this.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Now that phy_startup() can return an actual error code, check for that error
code and abort network initialization if the PHY fails.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Nobuhiro Iwamamatsu <nobuhiro.iwamatsu.yj@renesas.com> (sh_eth part)
Acked-by: Stephan Linz <linz@li-pro.net> (Xilinx part, xilinx_axi_emac and xilinx_ll_temac)
Reviewed-by: Marek Vasut <marex@denx.de> (FEC part)
phy_startup() calls the PHY driver's startup function, but it ignores the
return code from that function, and so it never returns any failures.
Signed-off-by: Timur Tabi <timur@freescale.com>
When support sh7734 of sh-ether, ECSIPR_BRCRXIP and other were removed.
Therefore SH7757 and SH7724 can not build. This revise this probelem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
This patch adds the following changes to designware ethernet driver
found on the ST SPEAr SoC:
- Don't init MAC & PHY upon startup. This causes a delay, waiting for
the auto negotiation to complete. And we don't want this delay to
always happen. Especially not on platforms where ethernet is not
used at all (e.g. booting via flash).
Instead postpone the MAC / PHY configuration to the stage, where
ethernet is first used.
- Add possibility for board specific PHY init code. This is needed
for example on the X600 board, where the Vitesse PHY needs to be
configured for GMII mode.
This board specific PHY init is done via the function
designware_board_phy_init(). And this driver now adds a weak default
which can be overridden by board code.
- Use common functions miiphy_speed() & miiphy_duplex() to read
link status from PHY.
- Print status and progress of auto negotiation.
- Print link status (speed, dupex) upon first usage.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
Few Designware peripheral registers need to be modified based on the
ethernet interface selected by the board. This patch supports interface
information in ethernet driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
On DA850/OMAP-L138 it was observed that in RMII mode,
auto negotiation was not performed. This patch enables
auto negotiation in RMII mode. Without this patch, EMAC
initialization takes more time and sometimes tftp fails
in RMII mode.
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
SH7734 support GMII. This add register infomation and the function
which enable GMII.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
SH7734 has one channel ethernet device.
This support 10/100/1000Base, and RMII/MII/GMII.
And this has the same structure as SH7763.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Add several levels of DEBUG prints so that you can limit the noise to
the severety of your problem.
DEBUG_LL_STATE = Link local state machine changes
DEBUG_DEV_PKT = Packets or info directed to the device
DEBUG_NET_PKT = Packets on info on the network at large
DEBUG_INT_STATE = Internal network state changes
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Call a built-in dummy if none is registered... don't require
protocols to register a handler (eliminating dummies)
NetConsole now uses the ARP handler when waiting on arp
(instead of needing a #define hack in arp.c)
Clear handlers at the end of net loop
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Rename IP header related things to IP_UDP. The existing definition
of IP_t includes UDP header, so name it to accurately describe the
structure.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
These are all the files which use the API incorrectly but did not get
built using MAKEALL -a powerpc|arm. I have no compiler for them, but
the remaining issues should be far less than without this patch.
Any outstanding issues are left to the maintainers of boards that use
these drivers.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
rtl8169.c: In function 'rtl8169_initialize':
rtl8169.c:907:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
pcnet.c: In function 'pcnet_initialize':
pcnet.c:224:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
xilinx_axi_emac.c: In function 'xilinx_axiemac_initialize':
xilinx_axi_emac.c:646: warning: assignment from incompatible pointer type
Signed-off-by: Stephan Linz <linz@li-pro.net>
Fix this:
xilinx_emaclite.c: In function 'xilinx_emaclite_initialize':
xilinx_emaclite.c:371: warning: assignment from incompatible pointer type
Signed-off-by: Stephan Linz <linz@li-pro.net>
Fix this:
xilinx_ll_temac.c: In function 'xilinx_ll_temac_initialize':
xilinx_ll_temac.c:332: warning: assignment from incompatible pointer type
xilinx_ll_temac.c:340: warning: assignment from incompatible pointer type
Signed-off-by: Stephan Linz <linz@li-pro.net>
Fix this:
uli526x.c: In function 'uli526x_initialize':
uli526x.c:243:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
tsi108_eth.c: In function 'tsi108_eth_initialize':
tsi108_eth.c:745:13: warning: assignment from incompatible pointer type
tsi108_eth.c: In function 'tsi108_eth_recv':
tsi108_eth.c:989:4: warning: passing argument 1 of 'NetReceive' discards qualifiers from pointer target type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
rtl8139.c: In function 'rtl8139_initialize':
rtl8139.c:234:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ns8382x.c: In function 'ns8382x_initialize':
ns8382x.c:352:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
natsemi.c: In function 'natsemi_initialize':
natsemi.c:338:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
eth.c: In function 'fm_eth_initialize':
eth.c:651:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
e1000.c: In function 'e1000_initialize':
e1000.c:5264:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
smc91111.c: In function 'smc91111_initialize':
smc91111.c:1363:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
macb.c: In function 'macb_eth_initialize':
macb.c:564:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
lan91c96.c: In function 'lan91c96_initialize':
lan91c96.c:811:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
ks8695eth.c: In function 'ks8695_eth_initialize':
ks8695eth.c:236:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
ftmac100.c: In function 'ftmac100_initialize':
ftmac100.c:266:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
fec_mxc.c: In function 'fec_probe':
fec_mxc.c:926:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
enc28j60.c: In function 'enc28j60_initialize':
enc28j60.c:967:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
eepro100.c: In function 'eepro100_initialize':
eepro100.c:464:13: warning: assignment from incompatible pointer type
eepro100.c: In function 'eepro100_recv':
eepro100.c:694:4: warning: passing argument 1 of 'NetReceive' discards qualifiers from pointer target type
include/net.h:438:13: note: expected 'uchar *' but argument is of type 'volatile u8 *'
The use of a descriptor like this may mean DMA will update this at will
Beware this may be a source of trouble on some boards
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
dnet.c: In function 'dnet_eth_initialize':
dnet.c:380:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
dm9000x.c: In function 'dm9000_initialize':
dm9000x.c:636:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
dc2114x.c: In function 'dc21x4x_initialize':
dc2114x.c:305:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
cs8900.c: In function 'cs8900_initialize':
cs8900.c:326:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
calxedaxgmac.c: In function 'xgmac_rx':
calxedaxgmac.c:479:2: warning: passing argument 1 of 'NetReceive' discards qualifiers from pointer target type
include/net.h:438:13: note: expected 'uchar *' but argument is of type 'volatile unsigned char *'
calxedaxgmac.c: In function 'calxedaxgmac_initialize':
calxedaxgmac.c:547:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
at91_emac.c: In function 'at91emac_register':
at91_emac.c:524:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
armada100_fec.c: In function 'armada100_fec_register':
armada100_fec.c:723:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix:
4xx_enet.c: In function 'ppc_4xx_eth_initialize':
4xx_enet.c:2029: warning: assignment from incompatible pointer type
Tested on sequoia board.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fixes:
davinci_emac.c: In function 'davinci_emac_initialize':
davinci_emac.c:796:12: warning: assignment from incompatible pointer type [enabled by default]
Tested on da850_am18xxevm
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fixes:
tsec.c: In function 'tsec_initialize':
tsec.c:638:12: warning: assignment from incompatible pointer type
Tested on MPC8313e-RDB
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix:
mpc512x_fec.c: In function 'mpc512x_fec_initialize':
mpc512x_fec.c:634: warning: assignment from incompatible pointer type
Tested on mpc5121ads board using tftp and nfs commands.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix:
mpc5xxx_fec.c: In function 'mpc5xxx_fec_initialize':
mpc5xxx_fec.c:920: warning: assignment from incompatible pointer type
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
smc911x.c: In function 'smc911x_initialize':
smc911x.c:288:12: warning: assignment from incompatible pointer type
[enabled by default]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Abstract out common register setup. This also configured r_cntrl
to correct value at registration time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.
The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure SRIO switch system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to SRIO1 or SRIO2 by RCW.
3. RCW should configure the SerDes, SRIO interfaces correctly.
4. Slave must be powered on after master's boot.
5. Must define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE because of no ucode
locally.
For the slave module, need to finish these processes:
1. Set the boot location to SRIO1 or SRIO2 by RCW.
2. Set a specific TLB entry for the boot process.
3. Set a LAW entry with the TargetID SRIO1 or SRIO2 for the boot.
4. Slave's u-boot image should be generated specifically by
make xxxx_SRIOBOOT_SLAVE_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
... after commit "net/miiphy/serial: drop duplicate NAMESIZE
define" (sha1:f6add13) was applied. The building of the new
LL TEMAC network driver fails with error below:
xilinx_ll_temac.c: In function 'xilinx_ll_temac_initialize':
xilinx_ll_temac.c:301: error: 'NAMESIZE' undeclared (first use in this function)
xilinx_ll_temac.c:301: error: (Each undeclared identifier is reported only once
xilinx_ll_temac.c:301: error: for each function it appears in.)
Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The new implementation changes the timeout loop implementation to avoid 1 ms
delay in each failing test. It also configures the delay to 10usec.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
This patch forces the advertised capabilities during auto
negotiation to always be 10/100 Mbps and half/full as duplexing.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
If AN(auto-negotiation) is ON, speed bit of control register are not
applicable. Also phy registers were not getting programmed as per the
result of AN. This patch sets only AN bit & restart AN bit for AN ON
selection & programs PHY registers as per AN result.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Phy autonegotiation works only when the ethernet cable is plugged in.
Since the phy was configured only at the init time, a plugged in cable
was necessary to initialize the phy properly.
This patch keeps a flag to check if the phy initialization has
succeeded, and calls configure_phy routine at every init if this flag
reports otherwise.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
This patch solves a TX/RX problem which happens at 10Mbps, due to the
fact that we are not respecting 4 cyles of the phy_clk (2.5MHz) between
two consecutive writes on the same register.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
The code assumes the phy address to be > 0, which is not true, the phy address
can be in the range 0-31.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
The max frame length for normal descriptor can be 0x7FF i.e 2047. It was wrongly
specified as 2048. Currently, the max descriptor length is around 1500, so
redefining the mask to 1600
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
The network controller mac resets hardware address stored in MAC_HI and MAC_LO
registers if mac is resetted. So, hw mac address needs to be restored in case
mac is explicitly resetted from driver.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Xilinx LocalLink Tri-Mode Ether MAC driver can be
used by Xilinx Microblaze or Xilinx ppc405/440 in
SDMA and FIFO mode. DCR or XPS bus can be used.
The driver uses and requires MII and PHYLIB.
CP: 4 warnings: 'Use of volatile is usually wrong'
I won't fix this, because it depends on the network
driver subsystem.
Reported-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Some baords may use the GBE interface but they have no
phy connected to the interface and a direct MAC/MAC interface.
For them we need to get rid of compiler warnings.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
flush_dcache is not declared in the common.h API,
flush_dcache_range however is
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
flush_dcache is not declared in the common.h API,
flush_dcache_range however is
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
lzma: fix printf warnings
Remove CONFIG_SYS_EXTBDINFO from snapper9260.h
cmd_pxe.c: fix strict-aliasing warnings
net: smc91111: use mdelay()
doc: Fix some typos in different files
disk/part.c: Fix device enumeration through API
mkenvimage: Really set the redundant byte when applicable
mkenvimage: Don't try to detect comments in the input file
mkenvimage: Use mmap() when reading from a regular file
mkenvimage: Read/Write from/to stdin/out by default or if the filename is "-"
mkenvimage: More error handling
mkenvimage: Correct an include and add a missing one
mkenvimage: correct and clarify comments and error messages
MAKEALL: display SPL size if present
ARMV7/Vexpress: add missing get_ticks() and get_tbclk()
mkenvimage: fix usage message
cmd_fat: add FAT write command
fs/fat/fat_write.c: Fix GCC 4.6 warnings
FAT write: Fix compile errors
Ensure that transmit and receive buffers are cache-line aligned.
Invalidate cache for each packet as received, update receive buffer
descriptors one cache line at a time, flush cache before transmitting.
Original patch by Marek:
http://lists.denx.de/pipermail/u-boot/2012-February/117695.html
Signed-off-by: Eric Nelson <eric.nelson at boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
A few subsystems are using the same define "NAMESIZE". This has been
working so far because they define it to the same number. However, I
want to change the size of eth_device's NAMESIZE, so rather than tweak
the define names, simply drop references to it. Almost no one does,
and the handful that do can easily be changed to a sizeof().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
EDMR_INIT_CNT holds the check count of initialization.
Since there were more same values (1000), this collected as TIMEOUT_CNT.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Boards may have things they want done before or after normal phy config.
Letting the boards call drv->config allows them more flexibilty.
Boards affected by this change are corenet_ds and mpc8544ds.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Add the gigabit phy KSZ9021.
Also, add function ksz9021_phy_extended_write
/_read for access to the phys extended registers.
The environment variable "disable_giga"
can be used to disable 1000baseTx.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Surround non PHYLIB routines miiphy_restart_aneg
and miiphy_wait_aneg with ifndef CONFIG_PHYLIB.
When later PHYLIB is required it is easy to delete
the non-PHYLIB code. This separation idea
came from Andy Fleming.
fec_miiphy_read, and fec_miiphy_write changed to
fec_phy_read, and fec_phy_write with argument changes.
Deprecated miiphy_register is no longer used. Both
old and new PHYLIB code now use mdio_register.
Cleanup some debug prints.
Inline function fec_miiphy_fec_to_eth is no longer necessary.
Moved to the single call location.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter.
This feature is important on mx28 SoC for example that has two FEC ports.
Cc: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This adds ethernet driver for Calxeda xgmac found on Highbank SOC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Fix: WARNING: __aligned(size) is preferred over
__attribute__((aligned(size)))
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'next' of ../next:
mkenvimage: Add version info switch (-V)
mkenvimage: Fix getopt() error handling
mkenvimage: Fix some typos
phy: add Micrel KS8721BL phy definition
net: introduce per device index
mvgbe: remove setting of ethaddr within the driver
x86: Add support for specifying an initrd with the zboot command
x86: Refactor the zboot innards so they can be reused with a vboot image
x86: Add infrastructure to extract an e820 table from the coreboot tables
x86: Add support for booting Linux using the 32 bit boot protocol
x86: Clean up the x86 zimage code in preparation to extend it
x86: Import code from coreboot's libpayload to parse the coreboot table
x86: Initial commit for running as a coreboot payload
CHECKPATCH: ./board/esd/hh405/logo_320_240_8bpp.c
CHECKPATCH: ./board/esd/hh405/logo_1024_768_8bpp.c
CHECKPATCH: ./board/esd/hh405/logo_320_240_4bpp.c
CHECKPATCH: ./board/esd/hh405/logo_640_480_24bpp.c
CHECKPATCH: ./board/esd/apc405/logo_640_480_24bpp.c
CHECKPATCH: ./board/esd/voh405/logo_320_240_4bpp.c
CHECKPATCH: ./board/esd/voh405/logo_640_480_24bpp.c
CHECKPATCH: ./board/esd/hh405/fpgadata.c
CHECKPATCH: ./board/esd/pci405/fpgadata.c
CHECKPATCH: ./board/esd/tasreg/fpgadata.c
CHECKPATCH: ./board/esd/apc405/fpgadata.c
CHECKPATCH: ./board/esd/voh405/fpgadata.c
CHECKPATCH: ./board/esd/ash405/fpgadata.c
CHECKPATCH: ./board/esd/dasa_sim/fpgadata.c
CHECKPATCH: ./board/esd/ar405/fpgadata_xl30.c
CHECKPATCH: ./board/esd/ar405/fpgadata.c
CHECKPATCH: ./board/esd/plu405/fpgadata.c
CHECKPATCH: ./board/esd/wuh405/fpgadata.c
CHECKPATCH: ./board/esd/cpci405/fpgadata_cpci405.c
CHECKPATCH: ./board/esd/cpci405/fpgadata_cpci405ab.c
CHECKPATCH: ./board/esd/cpci405/fpgadata_cpci4052.c
CHECKPATCH: ./board/esd/canbt/fpgadata.c
CHECKPATCH: ./board/esd/du405/fpgadata.c
CHECKPATCH: ./board/esd/cpciiser4/fpgadata.c
CHECKPATCH: ./board/dave/PPChameleonEVB/fpgadata.c
avr32:mmu.c: fix printf() length modifier
fat.c: fix printf() length modifier
cmd_sf.c: fix printf() length modifier
Make printf and vprintf safe from buffer overruns
vsprintf: Move function documentation into header file
Add safe vsnprintf and snprintf library functions
Move vsprintf functions into their own header
Conflicts:
tools/mkenvimage.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
This adds support for the Micrel KS8721BL/SL PHY.
The definition is taken from the correspondent datasheet.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Fix:
e1000_spi.c: In function 'spi_free_slave':
e1000_spi.c:115: warning: unused variable 'hw'
e1000_spi.c: In function 'do_e1000_spi':
e1000_spi.c:472: warning: 'checksum' may be used uninitialized in this function
e1000_spi.c:472: note: 'checksum' was declared here
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Acked-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
A network driver should not touch the environment at all. This patch fixes
this behaviour by removing the code for setting a default/randomized MAC
address.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Eric Cooper <ecc@cmu.edu>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Siddarth Gore <gores@marvell.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Fix trailing white space, indentation by spaces instead of TABs,
excessive blank lines, trailing blank lines.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
at91_emac.c: In function 'at91emac_phy_init':
at91_emac.c:244:20: warning: variable 'duplex' set but not used
[-Wunused-but-set-variable]
at91_emac.c:244:13: warning: variable 'speed' set but not used
[-Wunused-but-set-variable]
Use new debug_cond() to fix these warnings. In the result, anumber of
inconsistent printf() formats are detected:
at91_emac.c: In function 'at91emac_read':
at91_emac.c:147:2: warning: format '%x' expects argument of type
'unsigned int', but argument 2 has type 'struct at91_emac_t *'
[-Wformat]
at91_emac.c: In function 'at91emac_write':
at91_emac.c:157:2: warning: format '%x' expects argument of type
'unsigned int', but argument 2 has type 'struct at91_emac_t *'
[-Wformat]
at91_emac.c:157:2: warning: format '%x' expects argument of type
'unsigned int', but argument 4 has type 'short unsigned int *'
[-Wformat]
at91_emac.c: In function 'at91emac_recv':
at91_emac.c:451:3: warning: format '%d' expects argument of type
'int', but argument 2 has type 'long unsigned int' [-Wformat]
at91_emac.c:451:3: warning: format '%x' expects argument of type
'unsigned int', but argument 4 has type 'long unsigned int' [-Wformat]
Fix these, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Jens Scharsig <js_at_ng@scharsoft.de>
Cc: Andreas Bießmann <andreas.devel@gmail.com>
Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
Fix:
ne2000_base.c: In function 'dp83902a_send':
ne2000_base.c:282:7: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
ne2000_base.c: In function 'dp83902a_RxEvent':
ne2000_base.c:376:5: warning: variable 'rsr' set but not used
[-Wunused-but-set-variable]
ne2000_base.c: In function 'dp83902a_TxEvent':
ne2000_base.c:513:5: warning: variable 'tsr' set but not used
[-Wunused-but-set-variable]
ne2000_base.c: In function 'dp83902a_ClearCounters':
ne2000_base.c:550:17: warning: variable 'cnt3' set but not used
[-Wunused-but-set-variable]
ne2000_base.c:550:11: warning: variable 'cnt2' set but not used
[-Wunused-but-set-variable]
ne2000_base.c:550:5: warning: variable 'cnt1' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
This fixes the build of the two sh boards shmin and r7780mp and qemu-mips
which currently fail to build due to dropped pre-CONFIG_NET_MULTI code.
This v2 patch minimizes the number of lines in the diff for easy review
and to eliminate any possible accidential changes resulting from moving
lines of code in the file. This also makes the register function very easy.
Any cleanups and improvements are intentionally deferred to follow-up patches
to keep this patch as simple and as easy to review as possible.
A new driver register function, ne2k_register() calls the existing
one-time setup part of the old init function and calls eth_register().
Changes to shmin, r7780mp and qemu-mips:
- Call the new ne2k_register() from board_eth_init() of the boards.
- Tested using qemu-mips board,
- Tested the two renesas / sh boards r7780mp and shmin to compile again,
and should work.
checkpatch-clean when "--ignore VOLATILE" is added to .checkpatch.conf,
and no warnings introduced in none of the three boards using this driver.
Signed-off-by: Bernhard Kaindl <bernhard.kaindl@gmx.net>
Fix:
inca-ip_sw.c: In function 'inca_switch_init':
inca-ip_sw.c:210:6: warning: variable 'v' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix the condition for number of phys in
davinci_eth_phy_detect() function.
CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT indicates number of
phys. From this commit id dc02badab4
davinci emac initilazed one less than the number of phy count.
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
For some reason code setting the speed based on the PHY feedback causes
troubles on AM3517 so hardcode 100Mbps for now.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
DaVinci EMAC is present on TI AM35xx SoCs (ARMv7) which run with D-Cache
enabled by default. So we have to take care and flush/invalidate the
cache before/after the DMA operations.
Please note that the receive buffer alignment to 32 byte boundary comes
from the old driver version I don't know if it is really needed or
alignment to cache line size is enough.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
On AM35xx CPPI RAM had different addresses when accessed from the CPU
and from the EMAC. We need to account this to deal with the buffer
descriptors correctly.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
DaVinci EMAC is found not only on DaVinci SoCs but on some OMAP3 SoCs
also. This patch moves common defines from arch-davinci/emac_defs.h to
drivers/net/davinci_emac.h
DaVinci specific PHY drivers hacked to include the new header. We might
want to switch to phylib in future.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
This adds support for the SMSC LAN87xx PHYs.
Following PHYs can be used by set CONFIG_PHY_SMSC to config.
- SMSC LAN8700
- SMSC LAN8710/LAN8720
- SMSC LAN8710/LAN8720
A setup of PHY was copied from linux kenrel.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Fixed white space errors; modified commit message a bit.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The original m88e1111s_config() does not do the SGMII mode
initialization and is buggy. Rewrite the function according to
3.0.6 kernel function m88e1111_config_init() in drivers/net/phy/marvell.c
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
The sh_eth driver had an own mii functions. However the function
didn't support the gigabit PHY. The U-Boot has the general phy driver
and miiphybb driver, and they already support it.
So this patch removes the own functions and uses the phy driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Several macros are used to identify and locate the microcode binary image
that U-boot needs to upload to the QE or Fman. Both the QE and the Fman
use the QE Firmware binary format to package their respective microcode data,
which is why the same macros are used for both. A given SOC will only have
a QE or an Fman, so this is safe.
Unfortunately, the current macro definition and usage has inconsistencies.
For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman
firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address
of NAND. There's no way to know by looking at a variable how it's supposed
to be used.
In the future, the code which uploads QE firmware and Fman firmware will
be merged.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
cs8900.c: In function 'get_reg_init_bus':
cs8900.c:69:14: warning: variable 'c' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
lan91c96.c: In function 'dump_memory_info':
lan91c96.c:157:7: warning: variable 'mem_info' set but not used
[-Wunused-but-set-variable]
lan91c96.c: In function 'smc_send_packet':
lan91c96.c:320:16: warning: variable 'ioaddr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
device is already in *normal* (D0) mode => it doesn't need to be wake-up.
With this patch, we only wake-up (writing on TEST_BYTE register) if PM_MODE
bits of PM_CTRL register is in sleep (D1/D2) mode.
Signed-off-by: Bertrand Cachet <bertrand.cachet@heig-vd.ch>
No one uses this driver, and it isn't converted to the NET_MULTI
framework (which we dropped recently), so drop this driver too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fix the following build warning in drivers/net/e1000.c
e1000.c: In function 'e1000_reset_hw':
e1000.c:1373:11: warning: variable 'icr' set but not used [-Wunused-but-set-variable]
e1000.c: In function 'e1000_phy_init_script':
e1000.c:4395:11: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Fix:
enc28j60.c: In function 'enc_receive':
enc28j60.c:435:5: warning: variable 'eir_reg' set but not used
[-Wunused-but-set-variable]
enc28j60.c: In function 'enc_poll':
enc28j60.c:503:5: warning: variable 'estat_reg' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
at91_emac.c: In function 'at91emac_write_hwaddr':
at91_emac.c:477:15: warning: variable 'dev' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
4xx_enet.c: In function 'ppc_4xx_eth_init':
4xx_enet.c:875:6: warning: variable 'ethgroup' set but not used [-Wunused-but-set-variable]
I used "__maybe_unused" here intentionally, since all other
alternatives to fix this compilation warning would result in more
ifdef's.
Signed-off-by: Stefan Roese <sr@denx.de>
* 'master' of git://git.denx.de/u-boot-arm:
arm, davinci: add DAVINCI_MMC_CLKID
arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
arm, davinci: da850/dm365 lowlevel cleanup
omap5: Add omap5_evm board build support.
omap4/5: Add support for booting with CH.
omap5: emif: Add emif/ddr configurations required for omap5 evm
omap5: clocks: Add clocks support for omap5 platform.
omap5: Add minimal support for omap5430.
omap: Checkpatch fixes
omap4: make omap4 code common for future reuse
GCC4.6: Squash warnings in onenand_base.c
GCC4.6: Fix common/usb.c on xscale
OneNAND: Add simple OneNAND SPL
PXA: vpac270: Enable the new generic MMC driver
PXA: Cleanup serial_pxa
PXA: Drop csb226 and innokom boards (unmaintained)
m28evk: Fix comment about the number of RAM banks
mx31: Fix checkpatch warnings in generic.c
mx31: Use proper IO accessor for GPR register
mx31: Remove duplicate definition for GPR register
qong: Use generic function for configuring GPR register
M28EVK: Enable USB HOST support
iMX28: Add USB HOST driver
iMX28: Add USB and USB PHY register definitions
M28: Add memory detection into SPL
iMX28: Fix ARM vector handling
M28: Add doc/README.m28 documentation
M28: Add MMC SPL
iMX28: Add support for DENX M28EVK board
iMX28: Add u-boot.sb target to Makefile
iMX28: Add image header generator tool
iMX28: Add driver for internal RTC
iMX28: Add GPMI NAND driver
iMX28: Add APBH DMA driver
iMX28: Add SPI driver
iMX28: Add GPIO control
iMX28: Add I2C bus driver
iMX28: Add PINMUX control
FEC: Add support for iMX28 quirks
iMX28: Add SSP MMC driver
iMX28: Initial support for iMX28 CPU
MX25: zmx25: GCC4.6 fix build warnings
da850: add new config file for AM18xx
BeagleBoard: config: Switch to ttyO2
OMAP3: Change omap3_evm maintainer
devkit8000: Fix NAND SPL on boards with 256MB NAND
integrator: enable Vpp and disable flash protection
integrator: add system controller header
integrator: make flash writeable on boot
integrator: use io-accessors for board init
integrator: move text offset to config
integrator: pass configs for core modules
ARM: remove superfluous setting of arch_number in board specific code.
SPL: Allow ARM926EJS to avoid compiling in the CPU support code
integrator: do not test first part of the memory
arm: a320: fix broken timer
ARM: define CONFIG_MACH_TYPE for all ronetix boards
dm646x: pass board revision info to kernel
dm646x: add new configuration for dm6467T
arm, davinci: Fix setting of the SDRAM configuration register
arm, davinci: Remove the duplication of LPSC functions
arm, davinci: Rename AM1808 lowlevel functions to DA850
da8xxevm: fix build error
ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
since commits:
davinci: emac: add support for more than 1 PHYs
062fe7d332
davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
fb1d6332b5
I get following warning on the enbw_cmc board:
Err: serial
Net: 5 ETH PHY detected
miiphy_register: non unique device name 'KSZ8873 @ 0x01'
DaVinci-EMAC
Hit any key to stop autoboot: 0
Also I see some debug printfs:
=> run load
+ emac_close
+ emac_ch_teardown
- emac_ch_teardown
+ emac_ch_teardown
- emac_ch_teardown
- emac_close
+ emac_open
- emac_open
Using DaVinci-EMAC device
reason is 062fe7d332 new define MAX_PHY.
This is set to 3! I get on this board 5 active phys, so
this leads in wrong memory writes ...
so I changed:
- define CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT to set
the MAX_PHY value, add a description in README
for the new CONFIG_SYS option.
- print an error message if more then MAX_PHYs are
detected.
- fill the active_phy_addr array in a for loop with
0xff
- changed printf() in debug_emac()
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Tom Rini <tom.rini@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fix:
fm.c: In function 'fm_init_common':
fm.c:398:6: warning: variable 'n' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.
Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-arm:
Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
arm: jadecpu: Readd MACH_TYPE_JADECPU
at91: defined mach-types for otc570 board in board config file
at91: defined mach-types for meesc board in board config file
mx31pdk: Enable D and I caches
ehci-mxc: remove incorrect comment
README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
mx53: Turn off child clocks before reconfigure perclk_root
qong: enable support for compressed images
imx: imx31_phycore.h: fix checkpatch warnings
vision2: Remove unused get_board_rev function
mx53smd: Remove unused get_board_rev function
mx53ard: Remove unused get_board_rev function
mx53evk: Remove unused get_board_rev function
mx53evk: Add RTC support
mx53loco: Remove unused get_board_rev function
mx53evk: Remove unneeded '1' from mx53evk.h
OMAP3: mvblx: Initial support for mvBlueLYNX-X
ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
omap3: mem: Move comments next to definitions
omap3: mem: Clean-up whitespaces
omap3: mem: Define and use common macros
Davinci: ea20: added PREBOOT to configuration
Davinci: ea20: added I2C support
Davinci: ea20: added video support
VIDEO: davinci: add framebuffer to da8xx
ARM: Davinci: added missing registers to hardware.h
Davinci: ea20: add gpios for LCD backlight control
Davinci: ea20: add gpio for keeping power on in board_late_init
Davinci: ea20: Add default U-Boot environment
Davinci: ea20: Add early init to get early output from console
Davinci: ea20: Add NAND support
Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
Davinci: ea20: set console on UART0
arm, davinci: add cam_enc_4xx support
arm926ejs, davinci: add missing spi defines for dm365
arm926ejs, davinci: add cpuinfo for dm365
arm, davinci: add lowlevel function for dm365 soc
arm, davinci: add header files for dm365
spl, nand: add 4bit HW ecc oob first nand_read_page function
arm, davinci: add support for new spl framework
spl: add option for adding post memory test to the SPL framework
net, davinci_emac: make clock divider in MDIO control register configurable
arm, usb, davinci: make USBPHY_CTL register configurable
usb, davinci: add enable_vbus() weak function
omap3evm: fix errors caused by multiple definitions
omap3evm: Add (quick) configuration for NAND only
omap3evm: Add (quick) configuration for MMC/SD only
omap3evm: move common config options to new file
omap3evm: Prepare to split configuration
omap3evm: Reorder related config options
omap/spl: actually enable the console
davinci_emac: compilation fix, phy is array now
omap3evm: Set environment variable 'ethaddr'
arm, arm926: fix missing symbols in NAND_SPL mode
arm, davinci: Add function lpsc_syncreset()
arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
arm/km: portl2 environment address update to P1B
arm/km: adapt bootcounter evaluation
arm/km: enable jffs2 cmds
arm/km: trigger reconfiguration for the Xilinx FPGA
arm/km: add boardid and hwkey to kernel command line
ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
netspace_v2: enable I2C EEPROM support
netspace_v2: fix SDRAM configuration
armada100: define CONFIG_SYS_CACHELINE_SIZE
pantheon: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: drop empty asm-offsets.s file
arm/km/mgcoge3un: enhance "waitforne" feature
arm/km: add variable waitforne to mgcoge3un
gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
ARM: dreamplug: fix compilation
ARM: DockStar: fix compilation
ARM: netspace_v2: fix warnings
am335x: Drop board_sysinfo struct
am335x: Temporarily add MACH_TYPE define
misc:pmic:samsung Enable PMIC driver at C210 Universal target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
smdkv310: use macro for mmc data read function address
smdkv310: use spl framework for mmc spl
SMDKV310: use get_ram_size() to validate dram size
SMDKV310: Initialize board id using CONFIG_MACH_TYPE
ORIGEN : use absolute paths and fix tool naming
ORIGEN : enable device tree support
MX25: tx25: Fix building due to missing MACH_TYPE
mx31: Add board support for HALE TT-01
mx31: add ESD control registers
mx31: define pins and init for UART2 and CSPI3
MX35: add support for flea3 board
MX51: vision2: add MACH_TYPE in config file
vision2: Remove unused header file
mx51evk: Remove unused get_board_rev function
mx51evk: Remove unneeded '1' from mx51evk.h
I2C: Fix mxc_i2c.c problem on imx31_phycore
mx35pdk: Add RTC support
mx51evk: Use GPIO API for configuring the IOMUX
mx51evk: Add RTC support
rtc: Make mc13783-rtc driver generic
qong: remove unneeded IOMUX settings
qong: Use mx31_set_gpr to setup USBH2 pins
mx31: Introduce mx31_set_gpr function
mx31pdk: Add MC13783 PMIC support
qong: remove unneeded "1" from qong.h
misc: pmic: fix regression in pmic_fsl.c (SPI)
mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
MX35: Drop unnecessary prototypes from imx-regs.h
I2C: added I2C-2 and I2C-3 to MX35
MX35: factorize common assembly code
MX35: add reset cause as provided by other i.MX
MX35: add pins definition for UART3
MX35: added ESDC structure to imx-regs
Fix:
rtl8139.c: In function 'rtl8139_probe':
rtl8139.c:256:15: warning: variable 'fullduplex' set but not used
[-Wunused-but-set-variable]
rtl8139.c:256:6: warning: variable 'speed10' set but not used
[-Wunused-but-set-variable]
rtl8139.c: In function 'rtl_transmit':
rtl8139.c:419:16: warning: variable 'txstatus' set but not used
[-Wunused-but-set-variable]
Change code to use new debug macros; also fix the new errors and
warnigns popping up now, like "error: 'to' undeclared" and some
"warning: format '%X' expects argument of type 'unsigned int', but
argument X has type 'long unsigned int'"
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
rtl8169.c: In function 'rtl_init':
rtl8169.c:742:13: warning: variable 'printed_version' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
pcnet.c: In function 'pcnet_probe':
pcnet.c:247:8: warning: variable 'chipname' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
Define CONFIG_SYS_EMAC_TI_CLKDIV for setting the clkdiv value
in the MDIO control register.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Sandeep Paulraj <s-paulraj@ti.com>
cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fix build problem:
mvgbe.c: In function 'mvgbe_initialize':
mvgbe.c:735: warning: implicit declaration of function 'get_random_hex'
dockstar.c: In function 'board_early_init_f':
dockstar.c:43: warning: implicit declaration of function 'kw_config_gpio'
dockstar.c: In function 'board_init':
dockstar.c:113: warning: implicit declaration of function 'kw_sdram_bar'
dockstar.c: In function 'set_leds':
dockstar.c:161: warning: implicit declaration of function 'readl'
dockstar.c:161: error: dereferencing pointer to incomplete type
dockstar.c:162: warning: implicit declaration of function 'writel'
dockstar.c:162: error: dereferencing pointer to incomplete type
dockstar.c:163: error: dereferencing pointer to incomplete type
dockstar.c:164: error: dereferencing pointer to incomplete type
make[1]: *** [dockstar.o] Error 1
make: *** [board/Seagate/dockstar/libdockstar.o] Error 2
Reported-by: Roland Kletzing <devzero@web.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Fix:
4xx_enet.c: In function 'enet_rcv':
4xx_enet.c:1772:21: warning: variable 'ef_ptr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Fix:
eepro100.c: In function 'read_hw_addr':
eepro100.c:926:6: warning: variable 'eeprom' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
ns8382x.c: In function 'ns8382x_check_duplex':
ns8382x.c:704:6: warning: variable 'hun' set but not used
[-Wunused-but-set-variable]
To fix this, we get rid of the NS8382X_DEBUG code and use standard
debug() instead.
This will now trigger a so far undetected warning:
ns8382x.c:780:2: warning: format '%X' expects argument of type
'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat]
Fix that, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 114d7fc0 "e1000: Rewrite EEPROM checksum error to give more
information" failed to initialize the checksum variable which should
result in random results. Fix that.
Commit 2326a94d caused a ton of "unused variable 'x'" warnings.
Fix these. While we are at it, remove some bogus parens.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
As a part of the manufacturing process for some of our custom hardware,
we are programming the EEPROMs attached to our Intel 82571EB controllers
from software using U-Boot and Linux.
This code provides several conditionally-compiled features to assist in
our manufacturing process:
CONFIG_CMD_E1000:
This is a basic "e1000" command which allows querying the controller
and (if other config options are set) performing EEPROM programming.
In particular, with CONFIG_E1000_SPI this allows you to display a
hex-dump of the EEPROM, copy to/from main memory, and verify/update
the software checksum.
CONFIG_E1000_SPI_GENERIC:
Build a generic SPI driver providing the standard U-Boot SPI driver
interface. This allows commands such as "sspi" to access the bus
attached to the E1000 controller. Additionally, some E1000 chipsets
can support user data in a reserved space in the E1000 EEPROM which
could be used for U-Boot environment storage.
CONFIG_E1000_SPI:
The core SPI access code used by the above interfaces.
For example, the following commands allow you to program the EEPROM from
a USB device (assumes CONFIG_E1000_SPI and CONFIG_CMD_E1000 are enabled):
usb start
fatload usb 0 $loadaddr 82571EB_No_Mgmt_Discrete-LOM.bin
e1000 0 spi program $loadaddr 0 1024
e1000 0 spi checksum update
Please keep in mind that the Intel-provided .eep files are organized as
16-bit words. When converting them to binary form for programming you
must byteswap each 16-bit word so that it is in little-endian form.
This means that when reading and writing words to the SPI EEPROM, the
bit ordering for each word looks like this on the wire:
Time >>>
------------------------------------------------------------------
... [7, 6, 5, 4, 3, 2, 1, 0, 15, 14, 13, 12, 11, 10, 9, 8], ...
------------------------------------------------------------------
(MSB is 15, LSB is 0).
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
A followup patch will be adding a configurable feature to enable
programming of E1000 EEPROMs from the command line or via the generic
U-Boot SPI interface.
In order for it to work it needs access to certain E1000-internal
functions, so export those in the e1000.h header file.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
As an aide to debugging, we should print out the expected value of the
EEPROM checksum in addition to just saying that it is wrong.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
By allocating the e1000 device structures much earlier, we can easily
generate better error messages and siginficantly clean things up.
The only user-visable change (aside from reworded error messages) is
that a detected e1000 device which fails to initialize due to software
or hardware error will still be allocated a device number.
As one example, consider a system with 2 e1000 PCI devices where the
first controller has a corrupted EEPROM. Using the old code the
second controller would be "e1000#0", while with this change it would be
"e1000#1".
This change should hopefully make such EEPROM errors much more
straightforward to handle correctly in boot scripts and the like.
It is also necessary for a followup patch which allows SPI programming
of an e1000 controller's EEPROM even if the checksum is invalid.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Consolidate the test for a dual-port NIC to one location for easy
modification, then fix support for the dual-port 82571.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
* 'master' of git://git.denx.de/u-boot-arm:
ARM: Add Calxeda Highbank platform
dkb: make mmc command as default enabled
Marvell: dkb: add mmc support
ARM: pantheon: add mmc definition
davinci: remove config.mk file from the sources
ARM:AM33XX: Add support for TI AM335X EVM
ARM:AM33XX: Added timer support
ARM:AM33XX: Add emif/ddr support
ARM:AM33XX: Add clock definitions
ARM:AM33XX: Added support for AM33xx
omap3/emif4: fix registers definition
davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
davinci: emac: add support for more than 1 PHYs
davinci: emac: add new features to autonegotiate for EMAC
da850evm: Move LPSC configuration to board_early_init_f()
omap4_panda: Build in cmd_gpio support on panda
omap: Don't use gpio_free to change direction to input
mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
OMAP3: overo : Add environment variable optargs to bootargs
OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
OMAP3: overo : Use ttyO2 instead of ttyS2.
da830: add support for NAND boot mode
dm36x: revert cache disable patch
dm644X: revert cache disable patch
devkit8000: Add malloc space
omap: spl: fix build break due to changes in FAT
OMAP3 SPL: Provide weak omap_rev_string
omap: beagle: Use ubifs instead of jffs2 for nand boot
omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
omap: overo: Configure mux for gpio10
SPL: Add DMA library
omap3: Add interface for omap3 DMA
omap3: Add DMA register accessors
omap3: Add Base register for DMA
arm, davinci: add missing LSPC define for MMC/SD1
U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
DaVinci: correct MDSTAT.STATE mask
omap4: splitting padconfs into common, 4430 and 4460
omap4: adding revision detection for 4460 ES1.1
omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
gplug: fixed build error as a result of code cleanup patch
kirkwood_spi: add dummy spi_init()
gpio: mvmfp: reduce include platform file
ARM: orion5x: reduce dependence of including platform file
serial: reduce include platform file for marvell chip
ARM: kirkwood: reduce dependence of including platform file
ARM: armada100: reduce dependence of including platform file
ARM: pantheon: reduce dependence of including platform file
Armada100: Add env storage support for Marvell gplugD
Armada100: Add SPI flash support for Marvell gplugD
Armada100: Add SPI support for Marvell gplugD
SPI: Add SPI driver support for Marvell Armada100
dreamplug: initial board support.
imx: fix coding style
misc: pmic: drop old Freescale's pmic driver
MX31: mx31pdk: use new pmic driver
MX31: mx31ads: use new pmic driver
MX31: mx31_litekit: use new pmic driver
MX5: mx53evk: use new pmic driver
MX5: mx51evk: use new pmic driver
MX35: mx35pdk: use new pmic driver
misc: pmic: addI2C support to pmic_fsl driver
misc: pmic: use I2C_SET_BUS in pmic I2C
MX5: efikamx/efikasb: use new pmic driver
MX3: qong: use new pmic driver
RTC: Switch mc13783 to generic pmic code
MX5: vision2: use new pmic driver
misc: pmic: Freescale PMIC switches to generic PMIC driver
misc:pmic:samsung Enable PMIC driver at GONI target
misc:pmic:max8998 MAX8998 support at a new PMIC driver.
misc:pmic:core New generic PMIC driver
mx31pdk: Remove unneeded config
mx31: provide readable WEIM CS accessor
MX51: vision2: Set global macros
I2C: Add i2c_get/set_speed() to mxc_i2c.c
ARM: Update mach-types
devkit8000: Add config to enable SPL MMC boot
devkit8000: protect board_mmc_init
arm, post: add missing post_time_ms for arm
cosmetic, post: Codingstyle cleanup
arm, logbuffer: make it compileclean
tegra2: Enable MMC for Seaboard
tegra2: Add more pinmux functions
tegra2: Rename PIN_ to PINGRP_
tegra2: Add more clock functions
tegra2: Clean up board code a little
tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
fec_mxc.c: In function 'fec_mii_setspeed':
fec_mxc.c:112:2: warning: format '%#lx' expects type 'long unsigned int', but
argument 2 has type 'u32'
fec_mxc.c: In function 'fec_recv':
fec_mxc.c:632:2: warning: format '%x' expects type 'unsigned int', but argument
2 has type 'long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
ks8695eth.c:199:2: warning: format '%x' expects type 'unsigned int', but
argument 4 has type 'volatile void *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
4xx_enet.c: In function 'ppc_4xx_eth_init':
4xx_enet.c:1352: warning: format '%08x' expects type 'unsigned int', but
argument 2 has type 'volatile struct mal_desc_t *'
4xx_enet.c:1352: warning: format '%08x' expects type 'unsigned int', but
argument 3 has type 'volatile struct mal_desc_t *'
4xx_enet.c:1365: warning: format '%08lx' expects type 'long unsigned int', but
argument 3 has type 'unsigned int'
4xx_enet.c:1376: warning: format '%08lx' expects type 'long unsigned int', but
argument 3 has type 'unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
remove macro CONFIG_EMAC_MDIO_PHY_NUM and depending macro EMAC_MDIO_PHY_NUM
as they are no longer needed with the support for more than 1 PHYs in davinci
emac driver.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
add support for more than 1 PHYs. Many of the davinci platforms have more
than 1 PHYs on thier board. This patch extends support in davinci emac
driver for upto 3 PHYs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
add more features like DUPLEX, 100MB link speed etc to auto negotiate
in EMAC driver. EMAC controller autonegotiates for these features with
PHYs which are on the board.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the
definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
It seems to be good practice to return the number of received bytes in the
eth_device's recv() callback, here: tse_eth_rx().
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Note: This is kind of guess work. The current code is preserved for
all RGMII related modes. It is different for flags=0 (GMII) and flags=5
(SGMII). The last case, SGMII, is successfully tested on
Altera's Terasic DE4.
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Only one board uses this driver (ns9750dev), but the board doesn't seem
to have an entry to actually build it in the Makefile/boards.cfg, so just
delete net support from its board config.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Everyone seems to have converted to the new enc28j60 driver, so drop
this older one which isn't used and doesn't support NET_MULTI.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The code had two paths depending on whether the card was to be
accessed from plain memory or the IO region. However the error
path checks whether IO region was obtained - twice. Fix up the
error path according to the probable intention.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch move the reset function from initialization to
driver register procedure.
Some embedded system supports wake on lan nowadays. On this kind of system,
the ftgmac100 will be still supplied power after the system has been
shut-down by Linux. Hence the register used by linux won't be clear
when the system has been powered-off.
The origin ftgmac100 driver in u-boot will only register
driver and functions to network stack and won't reset the ftgmac100
hardware if the network won't be used during boot-up.
This will lead ftgmac100 continue receiving packets and then might corrupt
linux kernel when booting up.
So we reorder the hardware reset function earlier to force the hardware
to be reset whether it will be used or not.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
The work-around for P4080 erratum SERDES9 says that the SERDES receiver
lanes should be reset after the XAUI starts tranmitting alignment signals.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MDIO controller to talk to external PHYs is on FM1-DTSEC1 so don't
allow disabling. If we disable it we end up powering the block down in
the SoC and thus can't communicate to any external PHYs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FM1-DTSEC1's MAC was being marked as disabled if the port was not
configured based on the SoC configuration. However we utilize the MAC
interface for MDIO and thus should NOT mark it disabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit a45dde2293 changed the dm9000
direct register access to standard IO. This should work
on the ColdFire platform as there are corresponding macros for
the LE devices. But the hardware settings on some ColdFire boards had
swapped the byte order which make the original macros such as out_le16
cannot work. To avoid changing the common io access code on ColdFire
platform, the DM9000_BYTE_SWAPPED define was added to make the dm9000 use
__raw* IO access on some ColdFire boards.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Add axi_ethernet driver for little-endian Microblaze.
RX/TX BDs and rxframe buffer are shared among all axi_ethernet MACs.
Only one MAC can work in one time.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Setup RX/TX ping-pong buffer for every emaclite IP separately.
The next patch move initialization directly to board code.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Before the Teranetics TN2020 PHY can be used, the SERDES lanes need to be
aligned, so wait for lane alignment before completing the startup sequence.
Note that this process can take up to three seconds.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The EC1_EXT, EC2_EXT, and EC3 bits in the RCW don't officially exist on the
P3060 and should always be set to zero.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Function dtsec_configure_serdes() needs to know where the TBI PHY registers
are in order to configure SGMII for proper SerDes operation.
During SGMII initialzation, fm_eth_init_mac() passing NULL for 'phyregs'
when it called init_dtsec(), because it was believed that phyregs was not
used. In fact, it is used by dtsec_configure_serdes() to configure the TBI
PHY registers.
We also need to define the PHY registers in struct fm_mdio.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Teranetics PHY does not properly report the link state
for fiber connections. The new PHY code actually checked the link,
and so the FM driver would refuse to talk over a linkless PHY.
But the link may actually be up, so now we always report it as up
for fiber connections on the tn2020.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix:
smc91111.c: In function 'smc_phy_configure':
smc91111.c:1194:6: warning: variable 'failed' set but not used [-Wunused-but-set-variable]
smc91111.c:1190:7: warning: variable 'phyaddr' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Esp. while printing the environment the output is usually longer than 512
bytes. Instead of cutting the message, send multiple 512 bytes packets.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This is long over due. All but two net drivers have been converted, but
those have now been dropped.
The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined. So here we scrub the
core code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These drivers have never been converted to NET_MULTI, and they are only
used by one board (BMW). So drop the drivers until someone feels like
rewriting them for NET_MULTI support.
Rather than punting the BMW board completely, just disable net support
in its board config. Seems to build fine without it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Add P3060 SoC specific information:cores setup, LIODN setup, etc
The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The SoC configuration may have more ports enabled than a given board
actually can utilize. Add a routinue that allows the board code to
disable a port that it knows isn't being used.
fm_disable_port() needs to be called before cpu_eth_init().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>