Merge branch 'master' of git://www.denx.de/git/u-boot-imx

This commit is contained in:
Tom Rini 2016-01-08 10:18:18 -05:00
commit b685c7348c
9 changed files with 43 additions and 81 deletions

View file

@ -13,7 +13,8 @@
int pfuze_mode_init(struct pmic *p, u32 mode)
{
unsigned char offset, i, switch_num;
u32 id, ret;
u32 id;
int ret;
pmic_reg_read(p, PFUZE100_DEVICEID, &id);
id = id & 0xf;

View file

@ -94,8 +94,9 @@ static void setup_iomux_enet(void)
/* Reset AR8031 PHY */
gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
udelay(500);
mdelay(10);
gpio_set_value(IMX_GPIO_NR(1, 25), 1);
udelay(100);
}
static iomux_v3_cfg_t const usdhc2_pads[] = {
@ -340,39 +341,6 @@ int board_mmc_init(bd_t *bis)
}
#endif
int mx6_rgmii_rework(struct phy_device *phydev)
{
unsigned short val;
/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
val &= 0xffe3;
val |= 0x18;
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
/* introduce tx clock delay */
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
val |= 0x0100;
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
return 0;
}
int board_phy_config(struct phy_device *phydev)
{
mx6_rgmii_rework(phydev);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
#if defined(CONFIG_VIDEO_IPUV3)
static void disable_lvds(struct display_info_t const *dev)
{

View file

@ -121,8 +121,9 @@ static void setup_iomux_enet(void)
/* Reset AR8031 PHY */
gpio_direction_output(ETH_PHY_RESET, 0);
udelay(500);
mdelay(10);
gpio_set_value(ETH_PHY_RESET, 1);
udelay(100);
}
static struct fsl_esdhc_cfg usdhc_cfg[2] = {
@ -187,39 +188,6 @@ int board_mmc_init(bd_t *bis)
return 0;
}
static int mx6_rgmii_rework(struct phy_device *phydev)
{
unsigned short val;
/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
val &= 0xffe3;
val |= 0x18;
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
/* introduce tx clock delay */
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
val |= 0x0100;
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
return 0;
}
int board_phy_config(struct phy_device *phydev)
{
mx6_rgmii_rework(phydev);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
#if defined(CONFIG_VIDEO_IPUV3)
struct i2c_pads_info mx6q_i2c2_pad_info = {
.scl = {

View file

@ -114,3 +114,18 @@ int gpio_free(unsigned gpio)
{
return 0;
}
int name_to_gpio(const char *name)
{
unsigned bank, pin;
char *end;
bank = simple_strtoul(name, &end, 10);
if (!*end || *end != ':')
return bank;
pin = simple_strtoul(end + 1, NULL, 10);
return (bank << MXS_PAD_BANK_SHIFT) | (pin << MXS_PAD_PIN_SHIFT);
}

View file

@ -51,7 +51,7 @@ static struct phy_driver AR8031_driver = {
.uid = 0x4dd074,
.mask = 0xffffffef,
.features = PHY_GBIT_FEATURES,
.config = ar8021_config,
.config = ar8035_config,
.startup = genphy_startup,
.shutdown = genphy_shutdown,
};

View file

@ -130,7 +130,7 @@ static int read_cpu_temperature(struct udevice *dev)
#elif defined(CONFIG_MX7)
static int read_cpu_temperature(struct udevice *dev)
{
unsigned int reg, tmp, start;
unsigned int reg, tmp;
unsigned int raw_25c, te1;
int temperature;
unsigned int *priv = dev_get_priv(dev);
@ -169,18 +169,25 @@ static int read_cpu_temperature(struct udevice *dev)
writel(TEMPMON_HW_ANADIG_TEMPSENSE1_FINISHED_MASK, &ccm_anatop->tempsense1_clr);
writel(TEMPMON_HW_ANADIG_TEMPSENSE1_MEASURE_TEMP_MASK, &ccm_anatop->tempsense1_set);
start = get_timer(0);
/* Wait max 100ms */
do {
/*
* Since we can not rely on finish bit, use 1ms delay to get
* temperature. From RM, 17us is enough to get data, but
* to gurantee to get the data, delay 100ms here.
*/
if (soc_rev() >= CHIP_REV_1_1) {
while ((readl(&ccm_anatop->tempsense1) &
TEMPMON_HW_ANADIG_TEMPSENSE1_FINISHED_MASK) == 0)
;
reg = readl(&ccm_anatop->tempsense1);
tmp = (reg & TEMPMON_HW_ANADIG_TEMPSENSE1_TEMP_VALUE_MASK)
>> TEMPMON_HW_ANADIG_TEMPSENSE1_TEMP_VALUE_SHIFT;
} while (get_timer(0) < (start + 100));
} else {
/*
* Since we can not rely on finish bit, use 10ms
* delay to get temperature. From RM, 17us is
* enough to get data, but to gurantee to get
* the data, delay 10ms here.
*/
udelay(10000);
reg = readl(&ccm_anatop->tempsense1);
tmp = (reg & TEMPMON_HW_ANADIG_TEMPSENSE1_TEMP_VALUE_MASK)
>> TEMPMON_HW_ANADIG_TEMPSENSE1_TEMP_VALUE_SHIFT;
}
writel(TEMPMON_HW_ANADIG_TEMPSENSE1_FINISHED_MASK, &ccm_anatop->tempsense1_clr);

View file

@ -43,7 +43,7 @@ void reset_cpu(ulong addr)
{
struct watchdog_regs *wdog = (struct watchdog_regs *)WDOG1_BASE_ADDR;
clrsetbits_le16(&wdog->wcr, 0, WCR_WDE);
clrsetbits_le16(&wdog->wcr, WCR_WT_MSK, WCR_WDE);
writew(0x5555, &wdog->wsr);
writew(0xaaaa, &wdog->wsr); /* load minimum 1/2 second timeout */

View file

@ -241,6 +241,7 @@
#define CONFIG_IMX_THERMAL
#ifndef CONFIG_SPL_BUILD
#define CONFIG_VIDEO
#ifdef CONFIG_VIDEO
#define CONFIG_CFB_CONSOLE
@ -257,5 +258,6 @@
#define CONFIG_VIDEO_BMP_LOGO
#define MXS_LCDIF_BASE MX6UL_LCDIF1_BASE_ADDR
#endif
#endif
#endif

View file

@ -16,3 +16,4 @@ struct watchdog_regs {
#define WCR_WDT 0x08
#define WCR_SRS 0x10
#define SET_WCR_WT(x) (x << 8)
#define WCR_WT_MSK SET_WCR_WT(0xFF)