The "mac id" command is used to initialize the EEPROM data to a specific
format, but it was not updating the CRC. This didn't cause any real
problems, because writing the data to the EEPROM will always update the
CRC anyway, but it did result in a bogus CRC warning.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).
The board boots from the NOR flash. Following devices
are supported:
- two ethernet devices (FEC and SMC911x on debug board)
- I2C
- PMIC (MC13892) via I2C interface
- UART
- NOR flash (64MB)
- NAND flash (2GB)
- basic access to mc9sdz60 registers via I2C interface
Signed-off-by: Stefano Babic <sbabic@denx.de>
The early bootup information is not print out due to
the UART pin iomux not set up correctly before board_init
Add the board_early_init_f function and enable the
CONFIG_BOARD_EARLY_INIT_F. Move the UART pin setting
from board_init to board_early_init_f function.
This patch also move the FEC pin iomux setup to the
board_early_init_f.
Signed-off-by: Jason Liu <r64343@freescale.com>
u-boot cannot be compiled after disabling CONFIG_PCI.
Place PCI related codes under #ifdef CONFIG_PCI
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Extend board specific parameters to include cpo, write leveling override
Extend write leveling sample to 0xf
Adding rcw overrid for quad-rank RDIMMs
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rather than defining it config.mk we can set it in config.h and remove
config.mk from several boards that don't need it.
We mimic what 4xx does and introduce CONFIG_RESET_VECTOR_ADDRESS for
config.h to set.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Move the parsing of hwconfig to determine if to use spd into common code
so we can share it across all boards instead of duplicating it
everywhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Moved the SRIO init out of corenet_ds and into common code for
8xxx/QorIQ processors that have SRIO. We mimic what we do with PCIe
controllers for SRIO.
We utilize the fact that SRIO is over serdes to determine if its
configured or not and thus can setup the LAWs needed for it dynamically.
We additionally update the device tree (to remove the SRIO nodes) if the
board doesn't have SRIO enabled.
Introduced the following standard defines for board config.h:
CONFIG_SYS_SRIO - Chip has SRIO or not
CONFIG_SRIO1 - Board has SRIO 1 port available
CONFIG_SRIO2 - Board has SRIO 2 port available
(where 'n' is the port #)
CONFIG_SYS_SRIOn_MEM_VIRT - virtual address in u-boot
CONFIG_SYS_SRIOn_MEM_PHYS - physical address (for law setup)
CONFIG_SYS_SRIOn_MEM_SIZE - size of window (for law setup)
[ These mimic what we have for PCI and PCIe controllers ]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Remove duplicated code in MPC8610HPCD board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in P1_P2_RDB boards and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in MPC8569MDS board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in MPC8568MDS board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in MPC8548CDS board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in MPC8641HPCN board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in MPC8544DS board and utilize the common
fsl_pcie_init_ctrl(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
We don't use the full fsl_pcie_init_ctrl() since we have to handle PCIE3
specially to setup the additional memory map region and we utilize a
single LAW to cover the controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in P2020DS board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in MPC8572DS board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since all the PCIe controllers are connected over SERDES on the SoCs we
can utilize is_serdes_configured() to determine if a controller is
enabled. After which we can setup the ATMUs and LAWs for the controller
in a common fashion and allow board code to specify what the controller
is connected to for reporting reasons.
We also provide a per controller (rather than all) for some systems that
may have special requirements.
Finally, we refactor the code used by the P1022DS to utilize the new
generic code.
Based on patch by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add spaces to cause the informational prints to line up with
the ones from init_func_ram() in board.c. Output now looks like
this:
....
DRAM: Detected 4096 MB of memory
This U-Boot only supports < 4G of DDR
You could rebuild it with CONFIG_PHYS_64BIT
DDR: 2 GiB (DDR2, 64-bit, CL=5, ECC off)
....
The prints from lbc_sdram_init() have also been modified to line
line up and changed to start with "LBC SDRAM" instead of the
confusing "SDRAM".
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
sdram_init() is used to initialize sdram on the lbc. Rename it
accordingly.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correct initdram to use phys_size_t to represent the size of
dram; instead of changing this all over the place, and correcting
all the other random errors I've noticed, create a
common initdram that is used by all non-corenet 85xx parts. Most
of the initdram() functions were identical, with 2 common differences:
1) DDR tlbs for the fixed_sdram case were set up in initdram() on
some boards, and were part of the tlb_table on others. I have
changed them all over to the initdram() method - we shouldn't
be accessing dram before this point so they don't need to be
done sooner, and this seems cleaner.
2) Parts that require the DDR11 erratum workaround had different
implementations - I have adopted the version from the Freescale
errata document. It also looks like some of the versions were
buggy, and, depending on timing, could have resulted in the
DDR controller being disabled. This seems bad.
The xpedite boards had a common/fsl_8xxx_ddr.c; with this
change only the 517 board uses this so I have moved the ddr code
into that board's directory in xpedite517x.c
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new is_serdes_configured to determine if TSECs are in SGMII mode and
report that on the various boards that use or can be configured in SGMII
mode in board_eth_init() instead of in the PCI init code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we have serdes support for all 85xx/86xx/Pxxx chips we can
replace the is_fsl_pci_cfg() code with the is_serdes_configured().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mimic support that exists on MPC8536DS on the MPC8572DS to allow booting
from NAND.
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On the P1022, the pins which drive the video display (DIU) are muxed with the
local bus controller (LBC), so if the DIU is active, the pins need to be
temporarily muxed to LBC whenever accessing NOR flash.
The code which handled this transition is checking and changing the wrong
bits in PMUXCR.
Also add a follow-up read after a write to NOR flash if we're going to
mux back to DIU after the write, as described in the P1022 RM.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since the driver is used not only on Freescale boards,
we move it to a common place for video drivers as
suggested by Wolfgang. The patch also cleans up the
top level Makefile.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Since board_hwconfig & cpu_hwconfig are defined as weak and dont have a
default value they will get put into the BSS if they aren't defined
elsewhere. This is problematic as we try to utilize hwconfig before
we've relocated and thus BSS isn't setup.
Instead of giving dummy values in the board files that utilize this
feature, we can just initialize the variables to an empty string and
thus move them out of the BSS if they aren't defined elsewhere.
Also made board_hwconfig & cpu_hwconfig arrays to reduce size associated
with string pointers vs arrays.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The duplication of the do_reset prototype has gotten out of hand,
and they're not all in sync. Unify them all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Timur Tabi <timur@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
Previously some mpc85xx boards printed indented messages such as the
following on bootup:
printf(" eTSEC4 is in sgmii mode.\n");
printf(" Serdes2 disalbed\n");
The bootup appearance looks cleaner if the indentation is removed which
aligns these messages with other bootup output.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
CC: galak@kernel.crashing.org
Display the 64-byte Reset Configuration Word (RCW) during boot, so that
there's no confusion as to what RCW U-boot is using.
Reset Configuration Word (RCW):
00000000: 4a500000 00000000 18181818 00008888
00000010: 28402400 00002000 fe800000 01200000
00000020: 00000000 00000000 00000000 000b0000
00000030: 00000000 00000000 00000000 00000000
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SQW/INT pin in RTC can be used for generating square wave(by default) or
as interrupt line. U-boot is registering this pin for interrupts.
Configuring SQW/INT bit as interrupt line during board initialization
to avoid spurious interrupts generated by square wave.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch is to fix build breakage and support new relocation
scheme for mx51evk.
- Correct IRAM base address and add size definition
The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than
0x1FFE8000 which is for older revision.
- Include imx-regs.h in mx51evk.h
Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be
referred to.
- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE
They are used to define init RAM layout.
- Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been
buried by Wolfgang's commit below
25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
The mx51evk u-boot has an issue that system will get reset
every 2 hours.
MC13892 has an inside charge timer which expires in 120 minutes.
If ICHRG and CHGAUTOB are not set properly, this timer expiration
will get system power recycled.
Since mx51evk has no Li-Ion battery on board, the patch sets
ICHRG in externally powered mode and sets CHGAUTOB bit to avoid
automatic charging, so that system will not get reset by this
timer expiration.
The patch also corrects the bit field definition of register 48
(Charger 0) per latest MC13892 Reference Manual.
Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
Remove u-boot.lds from mx5 and use the common u-boot.lds
of cpu layer. This patch also fix the building errors:
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_start'
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_end_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_end'
arch/arm/cpu/armv7/start.o: In function `_dynsym_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__dynsym_start'
Signed-off-by: Jason Liu <r64343@freescale.com>
Update to use the recent, common FSL PCI initialization code.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
800, 900, 1000, 1200MT/s data rate parameters are added for fixed sdram
setting. SPD based parameters and fixed parameters can be toggled by hwconfig.
To use fixed parameters,
hwconfig=fsl_ddr:sdram=fixed
To use SPD parameters,
hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a common helper that will set the PHY connection type based on enum.
We use this on eTSEC, UCC, and will with Fman in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After the recent cleanups, a number of config.mk files consist only of
a "PLATFORM_CPPFLAGS += -I$(TOPDIR)/board" entry whih is not needed.
Remove such entries. In most cases, that means that the whole
config.mk file can be removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Clean up Makefile, and drop a lot of the config.mk files on the way.
We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
When planning for more generalization and Makefile cleanup it became
obvious that the introduction of a separate CONFIG_MK_ name space for
config options that were set through scripting in the Makefile was
not a good idea.
Originally the idea was to provide a script-free approach to supply
configuration options - there was no real need for a separate name
space. But when we now convert the existing Makefile entries to make
use of this approach, it would mean that we have to touch a large
number of board config files and add #ifdef / #define sequences to
"convert" from the CONFIG_MK_ to the CONFIG_ name space.
It seems much cleaner to get rid of this somewhat arbitrary _MK
string now for the few boards that actually use it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
commit 6aa3d3bfaa
"83xx: Remove warmboot parameter from PCI init functions" missed
one mpc83xx_pcie_init callsite, causing this build error:
Configuring for MPC837XEMDS_HOST board...
pci.c: In function 'pci_init_board':
pci.c:141: error: too many arguments to function 'mpc83xx_pcie_init'
this patch extends the commit to include that callsite.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Doubled use of DECLARE_GLOBAL_DATA_PTR caused compile warning:
pci.c:71: warning: register used for two global register variables
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Originally the Makefile defines CONFIG_ADS5121_REV2 when configuring
for board mpc5121ads_rev2. The config in include/configs/mpc5121ads.h
expects a define CONFIG_MPC5121ADS_REV2 for this.
Therefore there are two defines used but only 1 is defined.
This patch renames references to CONFIG_ADS5121_REV2 to CONFIG_MPC5121ADS_REV2
to have one common define.
This patch fixes faulty mem size detection caused by wrong config in
include/configs/mpc5121ads.h
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
Freescale application note AN3638 describes an update to the NXID format,
which stores MAC addresses and related data on an on-board EEPROM. The new
version adds support for up to 23 MAC addresses, instead of just 8. Since
the initial implementation of NXID had a "0" in the 'version' field, this
new version is called "v1".
Boards that are shipped with EEPROMs in the NXID v1 format should define
CONFIG_SYS_I2C_EEPROM_NXID_1 instead of CONFIG_SYS_I2C_EEPROM_NXID.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We configure the controller but dont have virtual address space thus any
devices on the 4th controller are not accessible in u-boot.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the code which writes to the on-board EEPROM so that it can detect if
the write failed because the EEPROM is write-protected. Most of the 8xxx-class
Freescale reference boards use an AT24C02 EEPROM to store MAC addresses and
similar information. With this patch, if the EEPROM is protected, the
"mac save" command will display an error message indicating that the write
has not succeeded.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022DS can use either a 12.288MHz or a 11.2896MHz reference
clock for the audio codec, but by default both are disabled. Add a 'audclk'
hwconfig option that allows the user to choose which clock he wants.
The 12.288MHz clock allows the codec to use sampling rates of 16, 24, 32, 48,
64, and 96KHz. The 11.2896 clock allows 14700, 22050, 29400, 44100, 58800, and
88200Hz.
Also configure a pin muxing to select some SSI signals, which will disable
I2C1.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable half drive strength, set RTT to 60Ohm and set write leveling override.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The original code maps boot flash as non-cacheable region. When calling
relocate_code in flash to copy u-boot from flash to ddr, every loop copy command
is read from flash. The flash read speed will be the bottleneck, which consuming
long time to do this operation. To resovle this, map the boot flash as
write-through cache via tlb. And set tlb to remap the flash after code
executing in ddr, to confirm flash erase operation properly done.
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As stated in 2720178533,
the mx51evk has not CPLD and all references must be removed.
This patch drop a .h file that still remains in board
directory.
Signed-off-by: Stefano Babic <sbabic@denx.de>
On the Freescale P1022, the DIU and the LBC share address pins, which means
that when the DIU is active (e.g. the console is on the DVI display), NOR flash
cannot be accessed. So we use the weak accessor function feature of the CFI
flash code to temporarily switch the pin mux from DIU to LBC whenever we want
to read or write flash. This has a significant performance penalty, but it's
the only way to make it work.
This change allows the 'saveenv' command to work when the video display is
enabled. Erasing flash and writing to flash (with the 'cp' command) works,
but reading from flash (with the 'md' and 'cp' commands) does not. Also, while
flash is being written, the video display will be blank.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add support for the DIU controller. If CONFIG_VIDEO is defined, then
the console will appear on a DVI monitor instead of the serial port.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Move common code to the fsl_diu_fb.c file and remove obsolete
code from board files (aria, mpc8610hpcd and pdm360ng).
Move fsl_diu_fb.h file to the include directory.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This change lays the groundwork for the BOOTFLAG_* flags being removed.
This change has the small affect of delaying 100ms on PCI initialization
after a warm boot as opposed to the optimal 1ms on some boards.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
included the mpc8308_p1m board.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch cleans up the Freescale MPC8308RDB Development board support.
Things fixed:
- Removed unused PCIE2 definitions from configuration
- SICR{L,H} defines used for System I/O Configuration Registers values
instead of hardcoding
- CONFIG_SYS_SCCR_PCIEXP1CM used to enable PCIE clock instead of
writing to SCCR from the board code
- sleep mode stuff removed as MPC8308 has no support for deep sleep and
PMCCR1 register. board_early_init_f() removed.
- MPC8308 has no ERRATA for DDR controller so workaround removed
- 'assignment in if statement' issues solved
- use LBLAWAR_* defines instead of hardcoding
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The Freescale MPC8610 and MPC5121 DIU code had re-implement two features that already
existed in U-Boot: bitmap drawing and top-of-screen logo (CONFIG_VIDEO_LOGO).
So delete the 8610-specific code and use the built-in features instead.
Signed-off-by: Timur Tabi <timur@freescale.com>
In function board_early_init_r(), serdes will not be initialize yet.
Thus sRIO was always considered disabled. Move the check for sRIO into
misc_init_r() which is called after fsl_serdes_init().
Also, fixed warning associated with gur variable possibly not being
used.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Lian Minghuan <B31939@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The board specific parameters associated with quad rank dimms where
missing. This fixes it so the board will function if quad rank dimms
are placed in it.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
since commit 1384f3bb8a ethernet names
with spaces drop a
Warning: eth device name has a space!
message. This patch fix it for:
- "FEC ETHERNET" devices found on
mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
renamed to "FEC".
- "SCC ETHERNET" devices found on
mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
boards. Renamed to "FCC"
Tested on the kup4k board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Add support for the P4080DS board, with the following features:
* 36-bit only
* Boots from NOR flash
* FMAN drivers NOT supported
* SPD DDR initialization
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Verified on MPC8641HPCN with four DDR2 dimms. Each dimm has dual
rank with 512MB each rank.
Also check dimm size and rank size for memory controller interleaving
Signed-off-by: York Sun <yorksun@freescale.com>
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Previously we used an alias the pci node to determine which node to
fixup or delete. Now we use the new fdt_node_offset_by_compat_reg to
find the node to update.
Additionally, we replace the code in each board with a single macro call
that makes assumes uniform naming and reduces duplication in this area.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8641 boards actually only have PCIE not PCI. Rename so we are
uniform with regards to names so we can replace this code with templated
code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove dupliacted setting of PCI/PCIe address and offsets in board
config.h. Renamed CONFIG_SYS_PCI1/2_ADDR to CONFIG_SYS_PCI1/2ADDR on
MPC8641 boards since its really PCIE controllers and not PCI.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code to map SERDES configs to slot names is board specific and not
chip specific. Thus it should live in board/freescale/p1022ds/ and not
in arch/powerpc/cpu/.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Specifics:
1) 36-bit only
2) Booting from NOR flash only
3) Environment stored in NOR flash only
4) No SPI support
5) No DIU support
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers. Merge
this into a single spot.
To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.
In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.
I have done a successful ppc build all and tested a board or two from
each processor family.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We have several boards that use the same ICS307 CLK chip to drive the
System clock and DDR clock. Move the code into a common location so we
share it.
Convert the P2020DS board as the first to use the new common ICS307
code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Timur Tabi <timur@freescale.com>
The various boards that have PIXIS FPGAs have slightly different
register definitions, however there is some common functionality (like
reset, ICS307 clk control, etc) that can be shared.
The struct definition exists for MPC8536DS, MPC8544DS, MPC8572DS,
MPC8610HPCD, and MPC8641HPCN boards.
Also fixed ngpixis to be __packed__ instead of aligned.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch provides support for MPC8308RDB development board from
Freescale with a minimal set of features:
Dual UART is supported
NOR flash is supported
Both TSEC Ethernet controllers are supported
PCI Express initialization is supported
The following features are enabled in configuration but not fully tested:
I2C (used to get the board revision)
I2C-connected RTC
VSC7385 switch
There is one (hopefully) minor issue: on soft reset the board sometimes
resets twice. I've not managed to find the fix for this problem yet.
As a workaround instruction cache can be disabled.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
- Also modified the code to use io accessors.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Use a slighly larger value of CLK_CTRL for DDR at 667MHz
which fixes random crashes while linux booting.
Applicable for both NAND and NOR boot.
Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Do not enforce drivers to provide empty video_set_lut()
if they do not implement indexed color (8 bpp) frame
buffer support. Add default function to the cfb_console
driver and remove empty video_set_lut() functions.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The ngPIXIS is a board-specific FPGA, but the definition of the registers
is mostly consistent. On boards where it matter, register 9 is called
'brdcfg1' instead of 'dma', so rename the variable in the ngpixis_t
definition.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 15351855 "fsl-diu: Using I/O accessor to CCSR space" caused a
number of "passing argument 2 of 'out_be32' makes integer from pointer
without a cast" warnings; fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Jerry Huang <Chang-Ming.Huang@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
On the MPC85xx platform if we have SATA its connected on SERDES.
Determing if SATA is enabled via sata_initialize should not be board
specific and thus we move it out of the MPC8536DS board code.
Additionally, now that we have is_serdes_configured() we can determine
if the given SATA port is enabled and error out if its not in the
driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new is_serdes_configured covers a broader range of devices than the
PCI specific code. Use it instead as we convert away from the
is_fsl_pci_cfg() code.
Additionally move to setting LAWs for PCI based on if its configured.
Also updated PCI FDT fixup code to remove PCI controllers from dtb if
they are configured.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Using PPC I/O accessor to DIU I/O space instead of directly
read/write. It will prevent the dozen of compiler order issue
and PPC hardware order issue for accessing I/O space.
Using the toolchain(tc-fsl-x86lnx-e500-dp-4.3.74-2.i386.rpm)
can show up the order issue of DIU driver.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Changes reflect modifications in the fsl_esdhc driver
(the clk_enable field war removed in the configuration structure).
Signed-off-by: Stefano Babic <sbabic@denx.de>
The MPC83xx SERDES control is different from the other FSL PPC chips.
For now lets split it out so we can standardize on interfaces for
determining of a device on SERDES is configured.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
While we had ft_pci_board_setup it wasn't being called by
ft_board_setup. Fix that so we actually update the device tree PCI
nodes on P1_P2_RDB boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PDM360NG is a MPC5121E based board by ifm ecomatic gmbh.
Signed-off-by: Michael Weiss <michael.weiss@ifm.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.
Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
Now that the other architecture-specific lib directories have been
moved out of the top-level directory there's not much reason to have the
'_generic' suffix on the common lib directory.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk
This change is intended to clean up the top-level directory structure
and more closely mimic Linux's directory organization.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The CPUDIR variable points to the location of a target's CPU directory.
Currently, it is set to cpu/$CPU. However, using $CPUDIR will allow for
more flexibility in the future. It lays the groundwork for reorganizing
U-Boot's directory structure to support a layout such as:
arch/$ARCH/cpu/$CPU/* (architecture with multiple CPU types)
arch/$ARCH/cpu/* (architecture with one CPU type)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The Freescale P2020DS board uses a new type of PIXIS FPGA, called the ngPIXIS.
The ngPIXIS has one distinct new feature: the values of the on-board switches
can be selectively overridden with shadow registers. This feature is used to
boot from a different NOR flash bank, instead of having a register dedicated
for this purpose. Because the ngPIXIS is so different from the previous PIXIS,
a new file is introduced: ngpixis.c.
Also update the P2020DS checkboard() function to use the new macros defined
in the header file.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Refactor and document the Freescale PIXIS code, used on most 85xx and 86xx
boards. This makes the code easier to read and more flexible.
Delete pixis.h, because none of the exported functions were actually being
used by any other file. Make all of the functions in pixis.c 'static'.
Remove "#include pixis.h" from every file that has it.
Remove some unnecessary #includes.
Make 'pixis_base' into a macro, so that we don't need to define it in every
function.
Add "while(1);" loops at the end of functions that reset the board, so that
execution doesn't continue while the reset is in progress.
Replace in_8/out_8 calls with clrbits_8, setbits_8, or clrsetbits_8, where
appropriate.
Replace ulong/uint with their spelled-out equivalents. Remove unnecessary
typecasts, changing the types of some variables if necessary.
Add CONFIG_SYS_PIXIS_VCFGEN0_ENABLE and CONFIG_SYS_PIXIS_VBOOT_ENABLE to make
it easier for specific boards to support variations in the PIXIS registers
sets. No current boards appears to need this feature.
Fix the definition of CONFIG_SYS_PIXIS_VBOOT_MASK for the MPC8610 HPCD.
Apparently, "pixis_reset altbank" has never worked on this board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After determining how much DDR is actually in the system, set DBAT0 and
IBAT0 accordingly. This ensures that the CPU won't attempt to access
(via speculation) addresses outside of actual memory.
On 86xx systems, DBAT0 and IBAT0 (the BATs for DDR) are initialized to 2GB
and kept that way. If the system has less than 2GB of memory (typical for
an MPC8610 HPCD), the CPU may attempt to access this memory during
speculation. The zlib code is notorious for generating such memory reads,
and indeed on the MPC8610, uncompressing the Linux kernel causes a machine
check (without this patch).
Currently we are limited to power of two sized DDR since we only use a
single bat. If a non-power of two size is used that is less than
CONFIG_MAX_MEM_MAPPED u-boot will crash.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ATMEL flash does not have buffer write feature. Assgined
buffer_size = 1, so that when there is a write to the flash
will not use buffer write function.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Fix proper portsize: The register for portsize is either 00b, 01b,
or 1xb. The value that previous assigned is 32d.
Fix DRAM bring up: insert asm("nop") for every DRAM register setup
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Use correct definition for _MASK and _UNMASK. It was combined in
the previous used and causes confusion.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
The patch removes warnings at compile time and provides
some cleanup code:
- Removed comment on NAND (not yet supported) from lowlevel_init.S
- Removed NFMS bit definition from imx-regs.h
The bit is only related to MX.25/35 and can lead to confusion
- Moved is_soc_rev() to soc specific code (removed from mx51evk.c)
Signed-off-by: Stefano Babic <sbabic@denx.de>
The patch adds initial support for the Freescale mx51evk board.
Network (FEC) and SD controller (fsl_esdhc) are supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
There's no sensible reason to unite speed and interface type into
one variable. So split this variable enet_interface into two
vars: enet_interface_type, which hold the interface type and speed.
Also: add the possibility for switching between 10 and 100 MBit
interfaces on the fly, when running in FAST_ETH mode.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
When referring to PCIe and USB 'endpoint' is the standard naming
convention.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Remy Bohmer <linux@bohmer.net>
The core support for NAND booting is there already, so this patch
is pretty straightforward.
There is one trick though: top level Makefile expects nand_spl to
be in nand_spl/board/$(BOARDDIR), but we can fully reuse the code
from mpc8313erdb boards, and so to not duplicate the code we just
symlink nand_spl/board/freescale/mpc8315erdb to mpc8313erdb.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
o silence make during ln echo
o update documentation
o and avoid:
$ ./MAKEALL MPC8315ERDB_NAND
Configuring for MPC8315ERDB board...
sdram.o: In function `fixed_sdram':
/home/r1aaha/git/u-boot/nand_spl/board/freescale/mpc8313erdb/sdram.c:72: undefined reference to `udelay'
by renaming udelay -> __udelay in the spirit of commit
3eb90bad65 "Generic udelay() with watchdog
support".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Thanks to "Errata to MPC8569E PowerQUICC III Integrated Host Processor
Family Reference Manual, Rev. 0" document, which describes all eSDHC
pins, we can add 4-bits eSDHC support for MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We already map the page cache-inhibited. There is no reason we
shouldn't also be marking it guarded to prevent speculative accesses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rather than hard coding which TLB entry the FLASH is mapped with we can
use find_tlb_idx to determine the entry.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can use fsl_setup_hose to determine if we are a agent/end-point or
a host. Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can use fsl_setup_hose to determine if we are a agent/end-point or
a host. Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can use fsl_setup_hose to determine if we are a agent/end-point or
a host. Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
u-boot updates, before starting Linux, the memory node in the
DTS. As this is a "standard" feature, move this functionality
to the cpu.c file for mpc5xxx and mpc512x processors.
Signed-off-by: Heiko Schocher <hs@denx.de>
According to the PPC reference implementation the udelay() function is
responsible for resetting the watchdog timer as frequently as needed.
Most other architectures do not meet that requirement, so long-running
operations might result in a watchdog reset.
This patch adds a generic udelay() function which takes care of
resetting the watchdog before calling an architecture-specific
__udelay().
Signed-off-by: Ingo van Lil <inguin@gmx.de>
The same code exists both inside an #ifdef and outside of it.
Remove the extra code for all the 86xx boards.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 70ed869ea5.
There isn't any need to modify the API for fsl_pci_init_port to pass the
status of host/agent(end-point) status. We can determine that
internally to fsl_pci_init_port. Revert the patch that makes the API
change.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Setup QE pin multiplexing for USB function, configure needed BCSRs
and add some fdt fixups.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To make QE UART usable by Linux we should setup pin multiplexing
and turn UCC2 Ethernet node into UCC2 QE UART node.
Also, QE UART is mutually exclusive with UART0, so we can't enable
it if eSDHC is in 4-bits mode on pilot boards, or if it's a prototype
board with eSDHC in 1- or 4-bits mode.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SPI Flash (M25P40) is connected to the SPI1 bus, we need a few
qe_iop entries to actually enable SPI1 on these boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch sets memory window for Serial RapidIO on MPC8569E-MDS
boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simply add some defines, and adjust TLBe setup to include some
space for eLBC NAND.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
eSDHC is mutually exlusive with UART0 (in 4-bits mode) and I2C2
(in 1-bit mode). When eSDHC is used, we should switch u-boot console to
UART1, and make the proper device-tree fixups.
Because of an erratum in prototype boards it is impossible to use eSDHC
without disabling UART0 (which makes it quite easy to 'brick' the board
by simply issung 'setenv hwconfig esdhc', and not able to interact with
U-Boot anylonger).
So, but default we assume that the board is a prototype, which is a most
safe assumption. There is no way to determine board revision from a
register, so we use hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Originally written by Jason Jin and Mingkai Hu for mpc8536.
When QorIQ based board is configured as a PCIe agent, then unlock/enable
inbound PCI configuration cycles and init a 4K inbound memory window;
so that a PCIe host can access the PCIe agents SDRAM at address 0x0
* Supported in fsl_pci_init_port() after adding pcie_ep as a param
* Revamped copyright in drivers/pci/fsl_pci_init.c
* Mods in 85xx based board specific pci init after this change
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The data being modified was in NOR flash which caused the crash.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On Chip BootROM support for P1 and P2 series RDB platforms.
This patch is derived from latest On Chip BootROM support on MPC8536DS
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
NAND Boot support for P1 and P2 series RDB platforms.
This patch is derived from NAND Boot support on MPC8536DS.
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 054197ba and later fixes used an array to initialize some of
the MDDRC parameters; however, the use of an array turned out to be a
bad idea as it was not possible to correlate structure entries to
array indices in readable and reliable way. Now we use a struct
instead, which makes this self-explanatory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The following changes allow U-Boot to fully relocate from flash to
RAM:
- Remove linker scripts' .fixup sections from the .text section
- Add -mrelocatable to PLATFORM_RELFLAGS for all boards
- Define CONFIG_RELOC_FIXUP_WORKS for all boards
Previously, U-Boot would partially relocate, but statically initialized
pointers needed to be manually relocated.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The MPC8536E is capable of booting from the on-chip ROM - boot from
eSDHC and boot from eSPI. When power on, the porcessor excutes the
ROM code to initialize the eSPI/eSDHC controller, and loads the mian
U-Boot image from the memory device that interfaced to the controller,
such as the SDCard or SPI EEPROM, to the target memory, e.g. SDRAM or
L2SRAM, then boot from it.
The memory device should contain a specific data structure with control
word and config word at the fixed address. The config word direct the
process how to config the memory device, and the control word direct
the processor where to find the image on the memory device, or where
copy the main image to. The user can use any method to store the data
structure to the memory device, only if store it on the assigned address.
The on-chip ROM code will map the whole 4GB address space by setting
entry0 in the TLB1, so the main image need to switch to Address space 1
to disable this mapping and map the address space again.
This patch implements loading the mian U-Boot image into L2SRAM, so
the image can configure the system memory by using SPD EEPROM.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8536E can support booting from NAND flash which uses the
image u-boot-nand.bin. This image contains two parts: a 4K
NAND loader and a main U-Boot image. The former is appended
to the latter to produce u-boot-nand.bin. The 4K NAND loader
includes the corresponding nand_spl directory, along with the
code twisted by CONFIG_NAND_SPL. The main U-Boot image just
like a general U-Boot image except the parts that included by
CONFIG_SYS_RAMBOOT.
When power on, eLBC will automatically load from bank 0 the
4K NAND loader into the FCM buffer RAM where CPU can execute
the boot code directly. In the first stage, the NAND loader
copies itself to RAM or L2SRAM to free up the FCM buffer RAM,
then loads the main image from NAND flash to RAM or L2SRAM
and boot from it.
This patch implements the NAND loader to load the main image
into L2SRAM, so the main image can configure the RAM by using
SPD EEPROM. In the first stage, the NAND loader copies itself
to the second to last 4K address space, and uses the last 4K
address space as the initial RAM for stack.
Obviously, the size of L2SRAM shouldn't be less than the size
of the image used. If so, the workaround is to generate another
image that includes the code to configure the RAM by SPD and
load it to L2SRAM first, then relocate the main image to RAM
to boot up.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this patch we can change QE USB mode without need to hand-edit
the device tree.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixes various ethernet issues with gigabit links handling
in U-Boot. The workarounds originally implemented by Kim Phillips for
Linux kernel.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Since commit 5c2ff323a9 ("mpc8360emds:
rework LBC SDRAM setup"), LBC SDRAM is available for use in Linux.
Though, it appears that QE Ethernet in Gigabit mode can't transmit
large packets when it tries to work with a data in LBC SDRAM (memtest
didn't discover any issues, is LBC SDRAM just too slow?).
With this patch we can still use the board without DDR memory, but
if DDR is available, we don't use LBC SDRAM.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Martha M Stan <mmarx@silicontkx.com>
Minor cleanup:
Re-ordered default_mddrc_config[] to have matching indices.
This allows to use the same index "N" for source and target fields;
before, we had code like this
out_be32(&im->mddrc.ddr_time_config2, mddrc_config[3]);
which always looked like a copy & paste error because 2 != 3.
Also, use NULL when meaning a null pointer.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Using the common 86xx fdt fixups removes some board-specific code and
should make the mpc8610hpcd easier to maintain in the long run.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1020/P1011 SOCs support max 32bit DDR width as opposed to P2020/P2010
where max DDR data width supported is 64bit.
As a next step the DDR data width initialization would be made more dynamic
with more flexibility from the board perspective and user choice.
Going forward we would also remove the hardcodings for platforms with onboard
memories and try to use the FSL SPD code for DDR initialization.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On 85xx platforms we shouldn't be using any LAWAR_* defines
but using the LAW_* ones provided by fsl-law.h. Rename any such
uses and limit the LAWAR_ to the 83xx platform as the only user so
we will get compile errors in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
General code cleanup to use in/out IO accessors as well as making
the code that prints out info sane between board and generic fsl pci
code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
So that we can set the NAND loader's relocate stack pointer
to the value other than the relocate address + 0x10000.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some board ports place TEXT_BASE at a location that would cause the
RESET_VECTOR_ADDRESS not to be at 0xfffffffc when we link. By default
we assume RESET_VECTOR_ADDRESS will be 0xfffffffc if the board doesn't
explicitly set it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Refactor the code into a simple bitmask lookup table that determines if
a given PCI controller is enabled and if its in host/root-complex or
agent/end-point mode.
Each processor in the PQ3/MPC86xx family specified different encodings
for the cfg_host_agt[] and cfg_IO_ports[] boot strapping signals.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ddr_pd_cntl isn't defined in any reference manual and thus we wil
remove especially since we set it to 0, which would most likely be its
POR value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The warning is bogus, so silence it by initializing the 'ret' variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The "mac id" command took a 4-character parameter as the identifier string.
However, for any given board, only one kind of identifier is acceptable, so it
makes no sense to ask the user to type it in. Instead, if the user enters
"mac id", the identifier (and also the version, if it's NXID) will
automatically be set to the correct value.
Improve the message that is displayed when EEPROM is read during boot. It now
displays "EEPROM:" and then either an error message or the EEPROM identifier
if successful.
If the identifier in EEPROM is valid, then always reject a bad CRC, even if the
CRC field has not been initialized.
Don't force the MAC address count to MAX_NUM_PORTS or less. Forcing the value
to be changed resulting in an in-memory copy that does not match what's in
hardware, even though the user did not request that change.
Finally, always update the CRC value in the in-memory copy after any field
is changed, so that the CRC is always correct.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Call fsl_pci_init_port() to initialize all the PCIe ports on the board.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are really no differences between all the 85xx linker scripts so
we can just move to a single common one. Board code is still able to
override the common one if need be.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.
Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For historic reasons we had defined some additional PLATFORM_CPPFLAGS like:
PLATFORM_CPPFLAGS += -DCONFIG_MPC86xx=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC8641=1
However these are all captured in the config.h and thus redudant. Also
moved common 86xx flags into cpu/mpc86xx/config.mk.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For historic reasons we had defined some additional PLATFORM_CPPFLAGS
like:
PLATFORM_CPPFLAGS += -DCONFIG_E500=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC8548=1
However these are all captured in the config.h and thus redudant.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Every platform that calls fsl_pci_init calls fsl_pci_setup_inbound_windows
before it calls fsl_pci_init. There isn't any reason to just call it
from fsl_pci_init and simplify things a bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Every platform that calls fsl_pci_init calls pci_setup_indirect before
it calls fsl_pci_init. There isn't any reason to just call it from
fsl_pci_init and simplify things a bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_CS8900 to CONFIG_CS8900
- changed CS8900_BASE to CONFIG_CS8900_BASE
- changed CS8900_BUS?? to CONFIG_CS8900_BUS??
- cleaned up line lengths
- modified VCMA9 command function that accesses the device
- removed MAC address initialization from lib_arm/board.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_SMC911X* to CONFIG_SMC911X*
- cleaned up line lengths
- modified all boards that override weak function in this driver
- added
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
Rename sdram_mode_1 to sdram_mode and sdram_cfg_1 to sdram_cfg to match
the 86xx user's manual and other Freescale architectures
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p2020DS, MPC8536DS, MPC8572DS, MPC8544DS boards are capable of
swizzling the upper address bits of the NOR flash we boot out of which
creates the concept of "virtual" banks. This is useful in that we can
flash a test of image of u-boot and reset to one of the virtual banks
while still maintaining a working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8641HPCN board is capable of swizzling the upper address bit of
the NOR flash we boot out of which creates the concept of "virtual"
banks. This is useful in that we can flash a test of image of u-boot
and reset to one of the virtual banks while still maintaining a
working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
So far the console API uses the following naming convention:
======Extract======
typedef struct device_t;
int device_register (device_t * dev);
int devices_init (void);
int device_deregister(char *devname);
struct list_head* device_get_list(void);
device_t* device_get_by_name(char* name);
device_t* device_clone(device_t *dev);
=======
which is too generic and confusing.
Instead of using device_XX and device_t we change this
into stdio_XX and stdio_dev
This will also allow to add later a generic device mechanism in order
to have support for multiple devices and driver instances.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Since we have simple hwconfig interface now, we don't need
pci_external_arbiter variable any longer.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch simply converts the board to the hwconfig infrastructure.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
fdt_fixup_esdhc() will either disable or enable eSDHC nodes, and
also will fixup clock-frequency property.
Plus, since DR USB and eSDHC are mutually exclusive, we should
only configure the eSDHC if asked through hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for eSDHC on MPC837XERDB boards. The WP
switch doesn't seem to work on RDB boards though, the WP pin is
always asserted (can see the pin state when it's in GPIO mode).
FSL DR USB and FSL eSDHC are mutually exclusive because of pins
multiplexing, so user should specify 'esdhc' or 'dr_usb' options
in the hwconfig environment variable to choose between the
devices.
p.s.
Now we're very close to a monitor len limit (196 bytes left using
gcc-4.2.0), so also increase the monitor len by one sector (64 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Update serial boot DRAM's Internal RAM, vector table and DRAM in
start.S, serial flash's read status command over SPI and NOR
flash.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Now that we have 3 boards for the MPC512x it turns out that they all
use the very same fixed_sdram() code.
This patch factors out this common code into cpu/mpc512x/fixed_sdram.c
and adds a new header file, include/asm-ppc/mpc512x.h, with some
macros, inline functions and prototype definitions specific to MPC512x
systems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
sys_eeprom.c: In function 'do_mac':
sys_eeprom.c:323: warning: dereferencing type-punned pointer will break strict-aliasing rules
sys_eeprom.c: In function 'mac_read_from_eeprom':
sys_eeprom.c:395: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to
CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures
use
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
All drivers need to be converted to CONFIG_NET_MULTI.
This patch converts the dm9000 driver.
Signed-off-by: Thomas Smits <ts.smits@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
We support up to 8 mac addresses in system eeprom, so we define the macro
MAX_NUM_PORTS to limit the mac_count to 8, and update the number of ethxaddr
according to mac_count.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch supports UCC working at RMII mode on PIB board, fixup fdt blob to
support rmii in kernel. It also changes the name of enable_mpc8569mds_qe_mdio to
enalbe_mpc8569mds_qe_uec which is more accurate.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds NAND support to the MPC5121ADS board. Please
note that the image size increased since NAND support didn't
fit in the current image size (256k).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This commit changes the MPC512x code to use I/O accessor calls (i.e.
out_*() and in_*()) instead of using deprecated pointer accesses.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
We rename the board so we use a consistent name in U-Boot and in
Linux. Also, we use this opportunity to move the board into the
Freecale vendor directory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.
Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.
This patch cleans this up - for example:
Before:
=> help dtt
dtt - Digital Thermometer and Thermostat
Usage:
dtt - Read temperature from digital thermometer and thermostat.
After:
=> help dtt
dtt - Read temperature from Digital Thermometer and Thermostat
Usage:
dtt
Signed-off-by: Wolfgang Denk <wd@denx.de>
all arm boards except a few use the same cpu linker script
so move it to cpu/$(CPU)
that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
MPC8569 UART1 signals are muxed with PortF bit[9-12], we need to define
those pins before using UART1.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The BCSR17[7] = 1 will unlock the write protect of FLASH.
The WP# pin only controls the write protect of top/bottom sector,
That is why we can save env, but we can't write the first sector
before the patch.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Currently the clk_adj is 6 (3/4 cycle), The settings will cause
the DDR controller hang at the data init. Change the clk_adj
from 6 to 4 (1/2 cycle), make the memory system stable.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Rename the pci header for FSL HW so we can move some prototypes
in there and stop doing explicit externs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx
* Introduce determine_mp_bootpg() helper. We'll need this to address a
bug introduced in v2009.03 with 86xx MP booting. We have to make sure
to reserve the region of memory used for the MP bootpg() so other
u-boot code doesn't use it.
* Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to
allow cmd_mp.c to build and work. In the future we should look at
implementing all these functions. This could be common w/85xx if we
use spin tables on 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We're missing the board_lmb_reserve definitions that allow
cpu_mp_lmb_reserve to be called; this means that Linux
is free to reallocate reserved pages. Linux currently boots
because we're getting lucky - the page we've reserved is
high enough in memory that it isn't allocated by Linux
while we still need it to be in existence.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A recent gcc added a new unaligned rodata section called '.rodata.str1.1',
which needs to be added the the linker script. Instead of just adding this
one section, we use a wildcard ".rodata*" to get all rodata linker section
gcc has now and might add in the future.
However, '*(.rodata*)' by itself will result in sub-optimal section
ordering. The sections will be sorted by object file, which causes extra
padding between the unaligned rodata.str.1.1 of one object file and the
aligned rodata of the next object file. This is easy to fix by using the
SORT_BY_ALIGNMENT command.
This patch has not be tested one most of the boards modified. Some boards
have a linker script that looks something like this:
*(.text)
. = ALIGN(16);
*(.rodata)
*(.rodata.str1.4)
*(.eh_frame)
I change this to:
*(.text)
. = ALIGN(16);
*(.eh_frame)
*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
This means the start of rodata will no longer be 16 bytes aligned.
However, the boundary between text and rodata/eh_frame is still aligned to
16 bytes, which is what I think the real purpose of the ALIGN call is.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
The Nand flash was unable to read and write properly
due to Nand Chip Select (nCE) setup was in reverse
order. Also, increase the Nand time out value to 60.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
These were left in accidentally, and are not really useful unless the
code is as broken as it was when it was being developed.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The SerDes initialization should be finished before negating the reset
signal according to the reference manual. This isn't an issue on real
hardware, but we'd better stick to the specifications anyway.
Suggested-by: Liu Dave <DaveLiu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe
slots. Let's support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Update the 86xx reset sequence to try executing a board-specific reset
function. If the board-specific reset is not implemented or does not
succeed, then assert #HRESET_REQ. Using #HRESET_REQ is a more standard
reset procedure than the previous method and allows all board
peripherals to be reset if needed.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Added some info that is printed out when we boot to distiquish if we
built MPC8572DS_config vs MPC8572DS_36BIT_config since they have
different address maps.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The device tree's PHY addresses need to be fixed up if we're using the
SGMII Riser Card.
The 8572, 8536, and 8544 DS boards were modified to call this function.
Code idea taken from Liu Yu <yu.liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In the 36-bit physical config for MPC8572DS when need the start address
of memory and it size to be kept in phys_*_t instead of a ulong since
we support >4G of memory in the config and ulong cant represent that.
Otherwise we end up seeing the memory node in the device tree reporting
back we have memory starting @ 0 and of size 0.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we introduced the 36-bit config of the MPC8572DS board we had the
wrong PCI MEM bus address map. Additionally, the change to the address
map exposes a small issue in our dummy read on the ULI bus. We need
to use the new mapping functions to handle that read properly in the
36-bit config.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Clean up PCI mapping concepts in the 8641 config - rename _BASE
to _BUS, as it's actually a PCI bus address, separate virtual
and physical addresses into _VIRT and _PHYS, and use each
appopriately.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Because the inbound pci windows are mapped generously, set up
the more specific outbound windows first. This way, when we
search the pci regions for something, we will hit on the more
specific region. This can actually be a problem on systems
with large amounts of RAM.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
The PCI_REGION_MEMORY and PCI_REGION_MEM are a bit to similar and
can be confusing when reading the code.
Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY to clarify its used
for system memory mapping purposes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The diufb command usage formatting is non-standard. It was
made standard in preparation for larger command usage updates.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Rather than have the board code initialize SATA automatically during boot,
make the user manually run "sata init". This brings the SATA subsystem in
line with common U-Boot policy.
Rather than having a dedicated weak function "is_sata_supported", people
can override sata_initialize() to do their weird board stuff. Then they
can call the actual __sata_initialize().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The wake up ARP feature need use the memory to process
wake up packet, we enable auto self refresh to support it.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
For light loaded system, we use the 1T timing to gain better
memory performance, but for some heavily loaded system,
you have to add the 2T timing options to board files.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Introduce a new define to seperate out the virtual address that PCI
IO space is at from the physical address. In most situations these are
mapped 1:1. However any code accessing the bus should use VIRT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Introduce a new define to seperate out the virtual address that PCI
memory is at from the physical address. In most situations these are
mapped 1:1. However any code accessing the bus should use VIRT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Use the _MEM_PHYS defines instead of _MEM_BUS for LAW and real address fields
of TLBs. This is what we should have always been using from the start.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Use CONFIG_SYS_PCI*_IO_BUS for the bus relative address instead
of _IO_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_SYS_{PCI,RIO}_MEM_BUS for the bus relative address instead
of _MEM_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Added a CONFIG_SYS_FLASH_BASE_PHYS for use as the physical address and
maintain CONFIG_SYS_FLASH_BASE as the virtual address of the flash.
This allows us to deal with 36-bit phys on these boards in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Added a PIXIS_BASE_PHYS for use as the physical address and maintain
PIXIS_BASE as the virtual address of the PIXIS fpga registers.
This allows us to deal with 36-bit phys on these boards in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
MPC837XEMDS boards can support PCI-E via "PCI-E riser card". The card
provides two PCI-E (x2) ports. Though, only one port can be used in x2
mode. Two ports can function simultaneously in x1 mode.
PCI-E x1/x2 modes can be switched via "pex_x2" environment variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC8315ERDB boards features PCI-E x1 and Mini PCI-E x1 ports. Let's
support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When running in PCI agent mode, the PCI_CLK_OUT signals are not used, so do
not enable them. See the MPC8349EA Reference Manual, Section 4.4.2
"Clocking in PCI Agent Mode".
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- Move the TLB entry of PIXIS_BASE from TLB0 to TLB1[8], because in CAMP mode,
all the TLB0 entries will be invalidated after cpu1 brings up kernel, thus cpu0
can not access PIXIS_BASE anymore (any access will cause DataTLBError exception)
- Set CONFIG_SYS_DDR_TLB_START to 9 for MPC8572DS board.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
The IO port selection for MPC8544DS board:
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2 0x4, 0x5, 0x6, 0x7
PCIE3 0x6, 0x7
This patch changes the PCIE12 and PCIE2 logic more readable.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
PCIE2 and PCIE3 should be decided by corresponing bit in devdisr instead of
PCIE1 bit.
On MPC8572DS board, PCIE refers to PCIE1.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The IO port selection is not correct on MPC8572DS and MPC8544DS board.
This patch fixes this issue.
For MPC8572
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x7, 0xb, 0xc, 0xf
PCIE2 0x3, 0x7
PCIE3 0x7
For MPC8544
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2 0x4, 0x5, 0x6, 0x7
PCIE3 0x6, 0x7
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately. This makes the code easier to read
and understand, and facilitates mapping changes going forward.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits
instead of four.
In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It
should be safe as the fifth bit was defined as reserved and set to 0.
Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Add define used to determine if PCI1 interface is in PCI or PCIX mode.
Convert users of the old PORDEVSR_PCI constant to use MPC85xx_PORDEVSR_PCI1
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
All mpc8548-based boards should implement the suggested workaround
to CPU 2 errata. Without the workaround, its possible for the
8548's core to hang while executing a msync or mbar 0 instruction
and a snoopable transaction from an I/O master tagged to make
quick forward progress is present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
The DDR controller of 8548/8544/8568/8572/8536 processors
have the ECC data init feature, and the new DDR code is
using the feature, and we don't need the way with DMA to
init memory any more.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
address-cells defaults to 2, not 1; so in the unlikely
event that it isn't specified, this patch is required
for correct operation.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Since we've changed the memory map of the board, be nice and
add some checking to try to catch out-of-date .dts files. We do
this by checking the CCSRBAR location in the .dts and comparing
it to the CCSRBAR location in u-boot. If they don't match, a
warning msg is printed. This isn't foolproof, but it's simple and
will catch most of the cases where an out-of-date .dts is present,
including all of the cases where a new u-boot is used with an old
standard MPC8641 .dts file as supplied with Linux.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
This patch creates a memory map with all the devices
in 36-bit physical space, in addition to the 32-bit map.
The CCSR relocation is moved (again, sorry) to
allow for the physical address to be 36 bits - this
requires translation to be enabled. With 36-bit physical
addressing enabled, we are no longer running with VA=PA
translations. This means we have to distinguish between
the two in the config file. The existing region name is
used to indicate the virtual address, and a _PHYS variety
is created to represent the physical address.
Large physical addressing is not enabled by default.
Set CONFIG_PHYS_64BIT in the config file to turn this on.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
The memory map on the 8641hpcn is modified to look more like
the 85xx boards; this is a step towards a more standardized
layout going forward. As part of this change, we now relocate
the flash.
The regions for some of the mappings were far larger than they
needed to be. I have reduced the mappings to match the
actual sizes supported by the hardware.
In addition I have removed the comments at the head
of the BAT blocks in the config file, rather than updating
them. These get horribly out of date, and it's a simple
matter to look at the defines to see what they are set to
since everything is right here in the same file.
Documentation has been changed to reflect the new map, as this
change is user visible, and affects the OS which runs post-uboot.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
There's a lot of setup and foo for the second flash
bank. The problem is, this board doesn't actually have one.
Clean this up. Also, the flash is 8M in size. Get rid
of the confusing aliased overmapping, and just map 8M.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
You can't actually have both, and with some coming changes to
change the memory map for the board and support 36-bit physical,
we need the extra BAT that is being consumed by having both.
I also make non-PCI configs build cleanly, for the sake of sanity.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Fix compilation issue caused by a few mismatches.
Provide proper nand chip select enable/disable in
nand_hwcontrol() rather than in board_nand_init()
just enable once. Remove redundant local nand driver
functions - nand_read_byte(), nand_write_byte() and
nand_dev_ready() to use common nand driver.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Will use mcfmii.c driver in drivers/net rather than
keep creating new mii.c for each future platform.
Remove EB+MCF-EV123, cobra5272, idmr, M5235EVB,
M5271EVB, M5272C3, M5275EVB, M5282EVB, M5329EVB,
M5373EVB, M54451EVB, M54455EVB, M547xEVB, and M548xEVB's
mii.c
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Each different build for M54455EVB and M5235EVB will
create a u-boot.lds linker file. It is redundant to
keep the u-boot.lds
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
This patch defines 1M TLB&LAW size for NAND on MPC8536DS, assigns 0xffa00000
for CONFIG_SYS_NAND_BASE and adds other NAND supports in config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image.
Singed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The DDR1 LAW will precedence the DDR2 LAW, so remove
the second DDR LAW.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
The DDR controller of 86xx processors have the ECC data init
feature, and the new DDR code is using the feature, we don't
need the way with DMA to init memory again.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
This patch defines 1M TLB&LAW size for NAND on MPC8572DS, assigns
0xffa00000 for CONFIG_SYS_NAND_BASE and adds other NAND supports in
config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image, to
make room for the increased code size with NAND enabled.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it
can be shared by both 83xx and 85xx
- Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards
files which use lbus83xx_t.
- Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that
85xx can share them.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Converted MPC8610HCPD, MPC8641HPCN, and SBC8641D to use
fsl_pci_setup_inbound_windows() and ft_fsl_pci_setup().
With these changes the board code is a bit smaller and we get dma-ranges
set in the device tree for these boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Converted ATUM8548, MPC8536DS, MPC8544DS, MPC8548CDS, MPC8568MDS,
MPC8572DS, TQM85xx, and SBC8548 to use fsl_pci_setup_inbound_windows()
and ft_fsl_pci_setup().
With these changes the board code is a bit smaller and we get dma-ranges
set in the device tree for these boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
With this patch u-boot can fixup the dr_mode and phy_type properties
for the Dual-Role USB controller.
While at it, also remove #ifdefs around includes, they are not needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MPC837xE-MDS board's CPLD can auto-detect if the board is on the PIB,
standalone or acting as a PCI agent. User's Guide says:
- When the CPLD recognizes its location on the PIB it automatically
configures RCW to the PCI Host.
- If the CPLD fails to recognize its location then it is automatically
configured as an Agent and the PCI is configured to an external arbiter.
This sounds good. Though in the standalone setup the CPLD sets PCI_HOST
flag (it's ok, we can't act as PCI agents since we receive CLKIN, not
PCICLK), but the CPLD doesn't set the ARBITER_ENABLE flag, and without
any arbiter bad things will happen (here the board hangs during any config
space reads).
In this situation we must disable the PCI. And in case of anybody really
want to use an external arbiter, we provide "pci_external_aribter"
environment variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This involves configuring the SerDes and fixing up the flags and
PHY addresses for the TSECs.
For Linux we also fix up the device tree.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC837xE specs says that SerDes1 has:
— Two lanes running x1 SGMII at 1.25 Gbps;
— Two lanes running x1 SATA at 1.5 or 3.0 Gbps.
And for SerDes2:
— Two lanes running x1 PCI Express at 2.5 Gbps;
— One lane running x2 PCI Express at 2.5 Gbps;
— Two lanes running x1 SATA at 1.5 or 3.0 Gbps.
The spec also explicitly states that PEX options are not valid for
the SD1.
Nevertheless MPC8378 RDB and MDS boards configure the SD1 for PEX,
which is wrong to do.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Currently 64M of LBC SDRAM are mapped at 0xF0000000 which makes
it difficult to use (b/c then the memory is discontinuous and
there is quite big memory hole between the DDR/SDRAM regions).
This patch reworks LBC SDRAM setup so that now we dynamically
place the LBC SDRAM near the DDR (or at 0x0 if there isn't any
DDR memory).
With this patch we're able to:
- Boot without external DDR memory;
- Use most "DDR + SDRAM" setups without need to support for
sparse/discontinuous memory model in the software.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
mpc8536ds.c: In function 'is_sata_supported':
mpc8536ds.c:615: warning: unused variable 'devdisr'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The pixis sgmii command depend on the FPGA support on the board, some 85xx
boards support SGMII riser card but did not support this command, define
CONFIG_PIXIS_SGMII_CMD for those boards which support the sgmii command.
Not like 8544, 8572 has 4 eTsec so that the other two's pixis bits
are not supported by 8544. Therefor, define PIXIS_VSPEED2_MASK and
PIXIS_VCFGEN1_MASK in header file for both boards.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
mpc8572 supports all pcie controllers as end-points with cfg_host_agent=0.
Include host_agent == 0 decode for end-point determination.
This is not needed for the ds reference board since pcie3 will be a host
in order to connect to the uli chip. Include it here as a reference for
other mpc8572 boards.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay based on board ddr frequency and n_ranks.
* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay, 2T based on board ddr frequency and n_ranks.
* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.
* Set memory controller interleaving mode to bank interleaving, and disable
bank(chip select) interleaving mode by default, because the default on-board
DDR DIMMs are 2x512MB single-rank.
* Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Because some dimm parameters like n_ranks needs to be used with the board
frequency to choose the board parameters like clk_adjust etc. in the
board_specific_paramesters table of the board ddr file, we need to pass
the dimm parameters to the board file.
* move ddr dimm parameters header file from /cpu to /include directory.
* add ddr dimm parameters to populate board specific options.
* Fix fsl_ddr_board_options() for all the 8xxx boards which call this function.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Changing the flash from cacheable to cache-inhibited was taking a significant
amount of time due to the fact that we were iterating over the full 256M of
flash. Instead we can just flush the L1 d-cache and invalidate the i-cache.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SGMII and SATA share the serdes on MPC8536 CPU, When SATA disabled and the
driver still try to access the SATA registers, the cpu will hangup.
This patch try to fix this by reading the serdes status before the SATA
initialize.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
When aligning malloc()ed screen_base, invalid offset was added.
This not only caused misaligned result (which did not cause hardware
misbehaviour), but - worse - caused screen_base + smem_len to
be out of malloc()ed space, which in turn caused breakage of
futher malloc()/free() operation.
This patch fixes screen_base alignment.
Also this patch makes memset() that cleans framebuffer to be executed
on first initialization of diu, not only on re-initialization. It looks
correct to clean the framebuffer instead of displaying random garbage;
I believe that was disabled only because that memset caused breakage
of malloc/free described above - which no longer happens with the fix
described above.
Signed-off-by: Nikita V. Youshchenko <yoush@debian.org>
get_cpu_board_revision() returned board revision based on information stored
in global static struct eeprom. It should instead use one from local struct
board_eeprom, to which the data is actually read from EEPROM. The bug led to
system hang after printing L1 cache information on U-Boot startup. The problem
was observed on MPC8555CDS system and possibly affects other Freescale MPC85xx
boards using CFG_I2C_EEPROM_CCID.
The change has been successfully tested on MPC8555CDS system.
Signed-off-by: Rafal Czubak <rcz@semihalf.com>
The spd_dram code shifts the base address, then masks 20 bits, but
forgets to shift the base address back. Fix this by just masking the
base address correctly.
Found this bug while trying to relocate a DDR memory at the base != 0.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The new sys_eeprom.c supports both the old CCID EEPROM format and the new NXID
format, and so it obsoletes board/freescale/common/cds_eeprom.c. Freescale
86xx boards already use sys_eeprom.c, so this patch migrates the remaining
Freescale 85xx boards to use it as well. cds_eeprom.c is deleted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Affected boards:
hidden_dragon
MPC8544DS
MPC8610HPCN
R2DPLUS
TB0229
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544DS and 8572DS platforms support an optional SGMII riser card to
expose ethernet over an SGMII interface. Once the card is in, it is also
necessary to configure the board such that it uses the card, rather than
the on-board ethernet ports. This can either be done by flipping dip switches
on the motherboard, or by modifying registers in the pixis. Either way
requires a reboot.
This adds a command to allow users to choose which ports are routed through
the SGMII card, and which through the onboard ports. It also allows users
to revert to the current switch settings.
This code does not work on the 8572, as the PIXIS is different.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544 DS has an optional SGMII Riser card, which uses different PHY
addresses. Check if we are in SGMII mode, and invoke the SGMII Riser
setup code if so.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544DS and 8572DS systems have an optional SGMII riser card which
exposes new ethernet ports which are connected to the eTSECs via an
SGMII interface. The SGMII PHYs for this board are offset from the standard
PHY addresses, so this code modifies the passed in tsec_info structure to
use the SGMII PHYs on the card, instead.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Add FEC pin set and mii reset in __mii_init(). Change
legacy flash vendor from 2 to AMD LEGACY (0xFFF0),
change cfi_offset to 0, and change CFG_FLASH_CFI to
CONFIG_FLASH_CFI_LEGACY. Correct M54451EVB and
M54455EVB env settings in configuration file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The only board using this driver is the Freescale MPC8610HPCD board.
Removed initialization for the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
PCI I/O space is currently mapped 1:1 at 0xFA000000. Linux requires
PCI I/O space to start at 0 on the PCI bus. This patch maps PCI I/O
space such that 0xFA000000 in the processor's address space maps to 0
on the PCI I/O bus.
Signed-off-by Randy Vinson <rvinson@mvista.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Add the ability for the MPC8349EMDS to run in PCI Agent mode, acting as a
PCI card rather than a host computer.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Change the MPC8349EMDS board to use the generic PCI initialization code
for the mpc83xx cpu.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
There is no point in disabling the icache on 7xx/74xx/86xx parts and not
also flushing the icache. All callers of invalidate_l1_instruction_cache()
call icache_disable() right after. Make it so icache_disable() calls
invalidate_l1_instruction_cache() for us.
Also, dcache_disable() already calls dcache_flush() so there is no point
in the explicit calls of dcache_flush().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Incorrect CFG_HZ value, change 1000000 to 1000.
Rename #waring to #warning. RAMBAR1 uses twice
in start.S, rename the later to FLASHBAR. Insert
nop for DRAM setup. And, env_offset in linker file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Remove non-common flash driver in
board/freescale/m54455evb/flash.c. The non-cfi flash will
use CONFIG_FLASH_CFI_LEGACY to configure the flash
attribute.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset. I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: Scott Wood <scottwood@freescale.com>
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The recent change to move the .bss outside of the image gives older
binutils (ld from eldk4.1/binutils-2.16) some headache:
ppc_85xx-ld: u-boot: Not enough room for program headers (allocated 3, need 4)
ppc_85xx-ld: final link failed: Bad value
We workaround it by being explicit about the program headers and not
assigning the .bss to a program header.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Move to using absolute addressing always. Makes the scripts a bit more
portable and common
* Moved .bss after the end of the image. These allows us to have more
room in the resulting binary image for code and data.
* Removed .text object files that aren't really needed
* Make sure _end is 4-byte aligned as the .bss init code expects this.
(Its possible that the end of .bss isn't 4-byte aligned)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The thinko was quite silly indeed, I messed with !ptr. Normally this
would trigger some fault, but in U-Boot NULL pointer is equal to phys
0, so the code was working still, just didn't actually test mpc8315erdb
environment variable value. Heh.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Freescale ships MPC8315E-RDB boards either with TSEC1 and USB UTMI
support, or without TSEC1 but with USB ULPI PHY support in addition.
With this patch user can specify desired USB PHY.
Also, it seems that we can't distinguish the two boards in software, so
user have to set `mpc8315erdb' environment variable to either 'tsec1'
(TSEC1 enabled) or `ulpi' (board with ULPI PHY, TSEC1 disabled), so that
Linux will not probe for TSEC1.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Update the sys_eeprom.c file to handle both NXID and CCID EEPROM formats. The
NXID format replaces the older CCID format, but it's important to support both
since most boards out there still use the CCID format. This change is in
preparation for using one file to handle both formats. This will also unify
EEPROM support for all Freescale 85xx and 86xx boards.
Also update the 86xx board header files to use the standard CFG_I2C_EEPROM_ADDR
instead of ID_EEPROM_ADDR.
Signed-off-by: Timur Tabi <timur@freescale.com>
The 8544 DS doesn't have any cacheable Local Bus memories set up. By mapping
space for some anyway, we were allowing speculative loads into unmapped space,
which would cause an exception (annoying, even if ultimately harmless).
Removing LBC_CACHE_BASE, and using LBC_NONCACHE_BASE for the LBC LAW solves the
problem.
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch is based on the following patch sent a few minutes ago:
"NAND FSL UPM: driver re-write using the hwcontrol callback"
It is untested, of course. Anton, could you please give it a try.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
With the new LAW interface (set_next_law) we can move to letting the
system allocate which LAWs are used for what purpose. This makes life
a bit easier going forward with the new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
A number of board ports have empty version of board_early_init_f
for no reason since we control its via CONFIG_BOARD_EARLY_INIT_F.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove unused and unconfigured DDR test code from FSL 85xx boards.
Besides, other common code exists.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_OF_LIBFDT instead to support flattened device trees. It is
cleaner, has better functionality, and is better supported.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This was configured to use the deprecated CONFIG_OF_FLAT_TREE, change
to CONFIG_OF_LIBFDT.
WARNING: This conversion is untested because I do not have a board to
test it on.
NOTE: The FDT blob (DTS) must have an /aliases/ethernet0 and (optionally)
/aliases/ethernet1 property for the ethernet to work.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This patch gets rid of the spi_chipsel table and adds a handful of new
functions that makes the SPI layer cleaner and more flexible.
Instead of the spi_chipsel table, each board that wants to use SPI
gets to implement three hooks:
* spi_cs_activate(): Activates the chipselect for a given slave
* spi_cs_deactivate(): Deactivates the chipselect for a given slave
* spi_cs_is_valid(): Determines if the given bus/chipselect
combination can be activated.
Not all drivers may need those extra functions however. If that's the
case, the board code may just leave them out (assuming they know what
the driver needs) or rely on the linker to strip them out (assuming
--gc-sections is being used.)
To set up communication parameters for a given slave, the driver needs
to call spi_setup_slave(). This returns a pointer to an opaque
spi_slave struct which must be passed as a parameter to subsequent SPI
calls. This struct can be freed by calling spi_free_slave(), but most
driver probably don't want to do this.
Before starting one or more SPI transfers, the driver must call
spi_claim_bus() to gain exclusive access to the SPI bus and initialize
the hardware. When all transfers are done, the driver must call
spi_release_bus() to make the bus available to others, and possibly
shut down the SPI controller hardware.
spi_xfer() behaves mostly the same as before, but it now takes a
spi_slave parameter instead of a spi_chipsel function pointer. It also
got a new parameter, flags, which is used to specify chip select
behaviour. This may be extended with other flags in the future.
This patch has been build-tested on all powerpc and arm boards
involved. I have not tested NIOS since I don't have a toolchain for it
installed, so I expect some breakage there even though I've tried
fixing up everything I could find by visual inspection.
I have run-time tested this on AVR32 ATNGW100 using the atmel_spi and
DataFlash drivers posted as a follow-up. I'd like some help testing
other boards that use the existing SPI API.
But most of all, I'd like some comments on the new API. Is this stuff
usable for everyone? If not, why?
Changed in v4:
- Build fixes for various boards, drivers and commands
- Provide common struct spi_slave definition that can be extended by
drivers
- Pass a struct spi_slave * to spi_cs_activate and spi_cs_deactivate
- Make default bus and mode build-time configurable
- Override default SPI bus ID and mode on mx32ads and imx31_litekit.
Changed in v3:
- Add opaque struct spi_slave for controller-specific data associated
with a slave.
- Add spi_claim_bus() and spi_release_bus()
- Add spi_free_slave()
- spi_setup() is now called spi_setup_slave() and returns a
struct spi_slave
- soft_spi now supports four SPI modes (CPOL|CPHA)
- Add bus parameter to spi_setup_slave()
- Convert the new i.MX32 SPI driver
- Convert the new MC13783 RTC driver
Changed in v2:
- Convert the mpc8xxx_spi driver and the mpc8349emds board to the
new API.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Tested-by: Guennadi Liakhovetski <lg@denx.de>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The cross compiler is responsible for providing the correct libraries
and the logic to find the linking libraries.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Currently the serdes will not be initializated due to the
partid's error.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixes eeprom page size so that you can now write more than
64 bytes at a time.
It also makes the board take MAC addresses, if found, from EEPROM.
User should place up to 4 addresses at offset 0x7f00, for
eth{,1,2,3}addr. Any unused addresses should be zero. This group of
four six-byte values should have it's CRC at the end. crc32 and
eeprom commands can be used to accomplish this.
If CRC fails, MAC addresses come from the environment. If CRC
succeeds, the environment is overwritten at startup.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
in the spirit of commit 1ced121600,
85xx's "Update SVR numbers to expand support", simplify SPRIDR processing
and processor ID display. Add REVID_{MAJ,MIN}OR macros to make
REVID dependent code simpler. Also added PARTID_NO_E and IS_E_PROCESSOR
convenience macros.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch is stolen from Anton Vorontsov's patch
for mpc837xerdb boards.
The reference clk and xcorevdd voltage of serdes1/2
is same between mpc837xemds and mpc837xerdb.
8377E: LYNX1- 2 SATA LYNX2- 2 PCIE
8378E: LYNX1- 2 SGMII LYNX2- 2 PCIE
8379E: LYNX1- 2 SATA LYNX2- 2 SATA
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Each file that can be built here now follows some
CONFIG_ option so that they are appropriately built
or not, as needed. And CONFIG_ defines were added
to various board config files to make sure that happens.
The other board/freescale/*/Makefiles no longer need
to reach up and over into ../common to build their
individually needed files any more.
Boards that are CDS specific were renamed with cds_ prefix.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
When we go to 36-bit physical addresses we need to keep the concept of
the physical CCSRBAR address seperate from the virtual one.
For the majority of boards CFG_CCSBAR_PHYS == CFG_CCSRBAR
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linux understands "host" (default), "peripheral" and "otg" (broken).
Though, U-Boot doesn't restrict dr_mode variable to these values (think
of renames in future).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds qe pario pins configuration for AD7843 ADC/Touchscreen
controller and FHCI (QE USB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
On the MPC8377ERDB: 2 SATA and 2 PCI-E.
On the MPC8378ERDB: 2 PCI-E
On the MPC8379ERDB: 4 SATA
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware. Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Back in commit 975a083a5e where
I tried to "8610HPCD: Fix typos in two PCI setup registers", I
botched it due to not realizing that 8610 and 8641 had different
Global Utility Register defintions, one of which was like 85xx,
and the other wasn't. Correct this problem by introducing two
symbols, one for each 86xx SoC, but neither of which is named
anything like 85xx.
My bad. Lovely Wednesday with git bisect. You know.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The two symbols MPC86xx_PORDEVSR_IO_SEL and MPC86xx_PORBMSR_HA
were erroneously present as 85xx names and values, leftover from
the clone wars. Fix this by removing the 85xx cruft from the
86xx codebase.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This is the proper fix for a missing closing brace in the function
ft_cpu_setup() noticed by joe.hamman <at> embeddedspecialties.com.
The ft_cpu_setup() function in mpc8641hpcn.c should have been
removed earlier as it was under the obsolete CONFIG_OF_FLAT_TREE,
but was missed. Only, the sbc8641d was nominally still using it.
It all got ripped out, and the funcality that was in ft_board_setup()
was refactored to remove the CPU portions into the new file
cpu/mpc86xx/fdt.c instead. Make sbc8641d use this now.
Based loosely on an original patch from joe.hamman@embeddedspecialties.com
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Adds the support code in cpu/mpc86xx for the new law setup code
recently created fsl_law.c, and changes the MPC8641HPCN config
to use this code.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Definition update and change from 16bit to 32bit
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>
- Fix EEPROM_data structure definition according to System EEPROM Data Format.
- Read MAC addresses from EEPROM to ethXaddr before saving ethXaddr to
bd->bi_ethaddr.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
This patch implements the fsl_spi driver on the MPC8349EMDS evaluation board.
This board has an ST M25P40 4Mbit EEPROM on its SPI bus
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We should be using the _MEM_PHYS for LAW and TLB setup and not _MEM_BASE.
While _MEM_BASE & _MEM_PHYS are normally the same, _MEM_BASE should only
be used for configuring the PCI ATMU.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
* TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
* load)
Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Before, the order of arguments to the pixis_reset
command needed to be supplied in a hard-coded order.
Generalize the command parsing to allow any order.
Signed-off-by: James Yang <james.yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Convert the board/freescale/common/Makefile to use
CONFIG_* options to select which files to conditionally
compile into the board/freescale/common library rather
than conditionally compiling entire files.
Now handles::
CONFIG_FSL_PIXIS
CONFIG_FSL_DIU_FB
CONFIG_PQ_MDS_PIB
CONFIG_ID_EEPROM is introduced until CFG_ID_EEPROM is gone.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
mpc8360emds.c: In function 'ft_board_setup':
mpc8360emds.c:327: warning: assignment makes pointer from integer without a cast
mpc8360emds.c:329: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast
mpc8360emds.c:334: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast
mpc8360emds.c:341: warning: assignment makes pointer from integer without a cast
mpc8360emds.c:343: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast
mpc8360emds.c:348: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
use tree passed to us in local blob, not global fdt.
Also use fdt_path_offset to convert to relative offset, since absolute
reference is needed to check for rgmii-id mode string value.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]
For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.
The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
connected to SPI.
Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
In order to use GETH1 and GETH2 on the MPC8568E-MDS, we should reset
UCCs.
p.s Similar code exists in the Linux kernel board file (for capability
reasons with older U-Boots), but should be removed some day.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
The old macros made it difficult to know what WIMGE and perm bits
were set for a TLB entry. Actually use the bit masks for these items
since they are only a single bit.
Also moved the macros into mmu.h out of e500.h since they aren't specific
to e500.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Assumes the presence of the aliases node in the DTS to
locate the pci and serial nodes for fixups.
Use consistent fdtaddr and fdtfile in environment variables.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
convert to using simpler mpc85xx style fdt update code; streamline by
eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm
the old school FLAT_TREE code from 83xx (since the sbc8349 was just
converted over to using libfdt).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
mpc8360emds.c: In function ‘ft_board_setup’:
mpc8360emds.c:335: warning: assignment discards qualifiers from pointer target type
mpc8360emds.c:345: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
u-boot itself uses GMII mode on the 8360. Fix up UCC phy-connection-type
properties in the device tree so the PHY gets configured for internal delay on
RX only by the OS, as prescribed by mpc8360 rev. 2.1 pb mds erratum #2.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MPC837xEMDS board support:
* DDR2 400MHz hardcoded and SPD init
* Local bus NOR Flash
* I2C, UART, MII and RTC
* eTSEC RGMII
* PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
Despite user manual, BCSR9.7 is negated (high) on HRST, so
UART2 is disabled. Fix that and configure QE pins properly.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Include config.h earlier in the set of #includes
so as to avoid a incidental and duplicate definition
of CFG_CACHELINE_SIZE.
Signed-off-by: Jon Loeliger
Assumes the presence of the aliases node in the DTS to
locate the ethernet, pci and serial nodes for fixups.
Use consistent fdtaddr and fdtfile in environment variables.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
We already had defines for LAWAR_TRGT_IF_* that we should use
rather than creating new ones. Also, added some missing defines for
PCIE targets.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_*_ADDR as the base of the registers
instead of getting it via &immap.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers
instead of getting it via &immap->im_gur.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the MPC8544DS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update libfdt to commit 8eaf5e358366017aa2e846c5038d1aa19958314e from
the device tree compiler (dtc) project.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These two structures are still needed during the
initialization and setup of the DIU hardware.
So move them to the fsl_diu_fb.h file for now.
Official "blah".
Noticed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Basically, refactor the CFG_PIXIS_VBOOT_MASK values
into the separate board config files.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Add cfb console support to FSL 8610 DIU driver.
Inspect board version from PIXIS to obtain correct pixel format.
Use #define CONFIG_VIDEO in config file to enable fb console.
To switch monitor, set monitor variable to
0 - DVI, 1 - Single link LVDS, 2 - Double link LVDS
followed by "diufb init".
Preserve logo bitmap at the top of the fb console.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
1280x1024 and 1024x768 @ 32 bpp are supported now.
DVI, Single-link LVDS, Double-link LVDS are all supported.
Environmental variable "monitor" is used to specify monitor port.
A new command "diufb" is introduced to reinitialize monitor
and display a BMP file in the memory. So far, 1-bit, 4-bit,
8-bit and 24-bit BMP formats are supported.
diufb init
- initialize the diu driver
Enable the port specified in the environmental variable "monitor"
diufb addr
- display bmp file in memory.
The bmp image should be no bigger than the resolution, 1280x1024
for DVI and double-link LVDS, 1024x768 for single-link LVDS.
Note, this driver allocate memory but doesn't free it after use
It is written on purpose -- to avoid a failure of reallocation
due to memory fragement.
ECC of DDR is disabled for DIU performance. L2 data cache is also disabled.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon loeliger <jdl@freescale.com>
This Freescale logo is a 340 x 128 x 4bpp BMP file
that can be displayed by the DIU Framebuffer driver.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Basically, refactor the CFG_PIXIS_VBOOT_MASK values
into the separate board config files.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The RTC on the M1575 ULI chipset requires a dummy read before
we are able to talk to the RTC. We accomplish this by adding a
second memory region to the PHB the ULI is on and read from it.
The second region is added to maintain compatiabilty with Linux's
view of the PCI memory map.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
if a board/$(VENDOR)/common/Makefile exists, build it.
also add the first such case, board/freescale/common/Makefile, to
handle building board-shared EEPROM, PIXIS, and MDS-PIB code, as
dictated by board configuration.
thusly get rid of alternate build dir errors such as:
FATAL: can't create /work/wd/tmp/u-boot-ppc/board/freescale/mpc8360emds/../common/pq-mds-pib.o: No such file or directory
by putting the common/ mkdir command in its proper place (the common
Makefile). Common bits from existing individual board Makefiles have
been removed.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
add board_add_ram_info, to make memory diagnostic output more
consistent. u-boot banner output now looks like:
DRAM: 256 MB (DDR1, 64-bit, ECC on)
and for boards with SDRAM on the local bus, a line such as this is
added:
SDRAM: 64 MB (local bus)
also replaced some magic numbers with their equivalent define names.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The patch split the PIB init code from pci.c to a single file board/freescale/common/pq-mds-pib.c
And add Qoc3 ATM card support for MPC8360EMDS and MPC832XEMDS board.
Signed-off-by Tony Li <tony.li@freescale.com>
The PCIe bus that the ULI M1575 is connected to has no possible way of
needing more than the fixed amount of IO & Memory space needed by the ULI.
So make it use far less IO & memory space and have it use the shared LAW. This
free's up a LAW for PCIe1 IO space. Also reduce the amount of IO space needed
by each bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It looks like we had a merge issue that duplicated a bit of code
in ft_board_setup. Also, we need to set CONFIG_HAS_ETH0 to get
the MAC address properly set in the device tree on boot for TSEC1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
this adds libfdt support code for the freescale
mpc8313erdb, mpc832xemds, mpc8349emds, mpc8349itx,
and gp boards.
Boards remain compatible with OF_FLAT_TREE.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
PCI1 LAW mapping should use CFG_PCI1_MEM_PHY and not _BASE address.
Enable LBC and ECM errors and clear error registers.
Add tftpflash env var to get uboot from tftp server and flash it.
Add pci/pcie convenience env vars to display register space:
"run pcie3regs" to see all pcie3 ccsr registers
"run pcie3cfg" to see all cfg registers
Whitespace cleanup and MPC8544DS.h
Enable CONFIG_INTERRUPTS.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
MPC8323E based board with 64MB fixed SDRAM, 16MB flash,
five 10/100 ethernet ports connected via an ICPlus IP175C
switch, one PCI slot, and serial. Features not supported
in this patch are SD card interface, 2 USB ports, and the
two phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The OBJTREE != SRCTREE build scenario was broken.
This fixes it.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
There is a Common Flash Interface Driver existed. To use the CFI driver, define CFG_FLASH_CFI in configuration file.
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Add board port under new board/freescale directory
structure and reuse existing PIXIS FPGA support there.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Move the 8641HPCN's PIXIS code to the new directory
board/freescale/common/ as it will be shared by
future boards not in the same processor family.
Write a "pixis_reset" command that utilizes the FPGA
reset sequencer to support alternate soft-reset options
such as using the "alternate" flash bank, enabling
the watch dog, or choosing different CPU frequencies.
Add documentation for the pixis_reset to README.mpc8641hpcn.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
