* fdt_fixup_mtdparts is called from ft_board_setup
* Run "mtdparts default" to create NAND partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
* fdt_fixup_mtdparts is called from ft_board_setup
* run "mtdparts default" to create NAND, NOR partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
-A_007662 states that for x1 link width, PCIe2 controller trains in
Gen1 speed while configured for Gen2 speed.
Workaround:Set the width to x1 and speed to Gen2 by writing to
CCSR registers in PBI phase
-A_008007 states that PVR register may show random value.
Workaround: Reset PVR register using DCSR space in PBI phase
Add PBI based software workaround for A_007662 and A_008007
in t104x_pbi.cfg. This is required for SPL-based bootloaders
like NAND-boot, SD-boot, SPI-boot
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This support of CPLD includes
- Files and register definitions
- Command to switch alternate bank
- Command to switch default bank
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch will enable the support for SPL on iMX6 SabreSD.
It tested on SD2 and SD3 mmc port (Switch 1 or 2 of SW6)
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The i.MX6Q/DL sabreauto board has one NAND socket, set the
CONFIG_NAND_MXS and relevant NAND configurations to enable the
MXS NAND flash driver.
Add board level codes to set IOMUX and clock for GPMI-NAND and
BCH module.
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Since kernel 3.15 there are two dtb's for the imx53-qsb board:
imx53-qsb.dtb - For the boards with DA9053 PMIC
imx53-qsrb.dtb - For the boards with MC34708 PMIC
Change the 'fdt_file' dynamically, so that the correct dtb can be used depending
on the board variant.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environment is set
to that device.
Signed-off-by: Ye.Li <B37916@freescale.com>
Add support for the 4.3'' Seiko WVGA parallel display.
In order to direct the splash screen to the Seiko display:
=> setenv panel SEIKO-WVGA
=> save
=> reset
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
The config targets described in README are not present
any more, update the info to currently used targets.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Provide a public declaration of the board_spi_cs_gpio()
callback for i.MX SPI chip selects to prevent the warning
"Should it be static?" when compiling with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Removed settings in unsupported register fields. They didn’t
do anything, and in most cases, were not documented in the
reference manual.
Changed register settings to comply with JEDEC required values.
Changed timing parameters because they included full clock
periods that were doing nothing.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
[rebased on v2014.10-rc2]
Signed-off-by: Stefan Agner <stefan@agner.ch>
Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2
arm2 board. Since the LPDDR2 arm2 board has different DDR size, use
CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE.
Signed-off-by: Ye.Li <B37916@freescale.com>
This patch adds the i.MX6DL arm2 board support. The i.MX6DL ARM2
shared the same board with i.MX6Q ARM2 board since the i.MX6DL is
pin-pin compatible with i.MX6Q.
The patch also support the DDR 32-BIT mode option. Please define
CONFIG_DDR_32BIT in the board configure file to enable DDR 32-BIT
mode.But due to the board design, it's 64bit DDR buswidth physically,
so, if you CONFIG_DDR_32BIT, the DDR memory size will be half of it.
Signed-off-by: Ye.Li <B37916@freescale.com>
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Spin table is at the very beginning of boot code. Each core has an individual
release address within the spin table, the ft_cpu_setup fn updates the
"cpu-release-addr" property of each cpu node with the corresponding release
address.
Also fix CPU_RELEASE_ADDR to point to secondary_boot_func.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
DP-DDR is used for DPAA, separated from main memory pool for general
use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit).
Signed-off-by: York Sun <yorksun@freescale.com>
Since commit ddaf5c8f30
(patman: RunPipe() should not pipe stdout/stderr unless asked),
Patman spits lots of "Invalid MAINTAINERS address: '-'"
error messages for patches with global changes.
It takes too long for Patman to process them.
Anyway, "M: -" does not carry any important information.
Rather, it is just like a place holder in case of assigning
a new board maintainer. Let's comment out.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The "S: Orphan" in MAINTAINERS means that the maintainer in the
"M:" field is unreachable (i.e. the email address is not working).
(Refer to the definition of "Orphan" adopted in U-Boot
in the log of commit 31f1b654b2,
"boards.cfg: move boards with invalid emails to Orphan")
For patch files adding global changes, scripts/get_maintainer.pl
adds bunch of such invalid email addresses, which results in
tons of annoying bounce emails.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '
/^M:[[:blank:]]/ {
N
/S:[[:blank:]]Orphan/s/^/#/
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
T1042QDS (T1042 is T1040 Personality without L2 switch) supports following
sgmii interfaces with serdes protocol 0xA7
-SGMII-MAC3 on Lane B - slot 7
-SGMII-MAC5 on Lane H - slot 7
-SGMII2.5G-MAC1 on Lane C - slot 6
-SGMII2.5G-MAC2 on Lane D - slot 5
Add support of above sgmii interfaces
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
DDR-ODT require cfg_dram_type switch set properly as per DDR type.
T1040RDB, T1042RDB boards have DDR3L type DDR, so cfg_dram_type
should be set to OFF for DDR3L
Update t104xrdb/README for switch setting
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1042RDB is a Freescale reference board that hosts the T1042 SoC
(and variants). The board is similar to T1040RDB, T1042 is a reduced
personality of T1040 SoC without Integrated 8-port Gigabit(L2 Switch).
T1042RDB is configured with serdes protocol 0x86 which can support
following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 1 SGMII on DTSEC3
DTSEC1, DTSEC2 are not connected on board.
This Patch
- add T1042RDB support
- updates README file for T1042RDB details and update commands for switching
to alternate banks from vBank0 to vBank4 and vice versa
This patch also does minor clean ups for fdt defines for T1042RDB and
T1042RDB_PI board
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support of rcw for T1042RDB, it makes following changes :
- Adds t1042_rcw.cfg file for serdes protocol 0x86 for T1042RDB
- Renames t1042_pi_rcw.cfg file from t1042_rcw.cfg and also updates
comments for valid serdes protocol which is 0x06
- Also updates CONFIG_SYS_FSL_PBL_RCW for T1042RDB
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS2085a has 2 regions in system memory map. Region1 is default map from
where system boots. Once u-boot is moved to DDR, IFC is re-mapped to
Region2.
So, update gd->env_addr to reflect correct address.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MXC SPI driver has a feature whereas a GPIO line can be used to force CS high
across multiple transactions. This is set up by embedding the GPIO information
in the CS value:
cs = (cs | gpio << 8)
This merge of cs and gpio data into one value breaks the sf probe command:
if the use of gpio is required, invoking "sf probe <cs>" will not work, because
the CS argument doesn't have the GPIO information in it. Instead, the user must
use "sf probe <cs | gpio << 8>". For example, if bank 2 gpio 30 is used to force
cs high on cs 0, bus 0, then instead of typing "sf probe 0" the user now must
type "sf probe 15872".
This is inconsistent with the description of the sf probe command, and forces
the user to be aware of implementaiton details.
Fix this by introducing a new board function: board_spi_cs_gpio(), which will
accept a naked CS value, and provide the driver with the relevant GPIO, if one
is necessary.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Provide cgtqmx6eval board its own variant of ddr
setup config file. Move board/freescale/imx/ddr/
mx6q_4x_mt41j128.cfg to board/freescale/mx6sabresd/
as this is was designed for the mx6sabresd board.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
commit d6d07a9b... arm: vf610: add NAND support for vf610twr
generates the following warnings:
WARNING: no status info for 'vf610twr_nand'
WARNING: no maintainers for 'vf610twr_nand'WARNING: no status info for
'vf610twr_nand'
This is due to the fact that vf610twr_nand_defconfig has no Maintainer.
This patch proposed Alison as Maintainer and fix it.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Alison Wang <b18965@freescale.com>
CC: Stefan Agner <stefan@agner.ch>
i2c_pad_info1 is only used locally, so it can be made static.
Fix the following sparse warning:
board/freescale/mx6sxsabresd/mx6sxsabresd.c:160:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This adds NAND support for the Vybrid tower system (TWR-VF65GS10)
provided by the vf610_nfc driver. Full 16-Bit bus width is
supported. Also an aditional config vf610twr_nand is introduced
which gets the environment from NAND. However, booting U-Boot from
NAND is not yet possible due to missing boot configuration block
(BCB).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Currently mx6dlsabresd shares the same DCD settings with the nitrogen board.
Provide a DCD configuration file specific to mx6dlsabresd with the settings
recommended by the Freescale hardware team.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds the TWR_LCD_RGB card/HDMI options and the common
configuration for DCU on LS1021ATWR board.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
On LS1021ATWR, Silicon's Sii9022A HDMI Transmitter
is used. This patch adds the common setting for this
chip.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021ATWR board.
One DDR controller
DUART1 is used as the console
For the detail board information, please refer to README.
Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021AQDS board.
One DDR controller
DUART1 is used as the console
For the detail board information, please refer to README.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
fsl_enet.h defines the mapping of the usual MII management
registers, which are included in the MDIO register block
common to Freescale ethernet controllers. So it shouldn't
depend on the CPU architecture but it should be actually
part of the arch independent fsl_mdio.h.
To remove the arch dependency, merge the content of
asm/fsl_enet.h into fsl_mdio.h.
Some files (like fm_eth.h) were simply including fsl_enet.h
only for phy.h. These were updated to include phy.h instead.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
XFI is supported on T4QDS-XFI board, which removed slot3, and four LANEs
of serdes2 are routed to a SFP+ cages, which to house fiber cable or
direct attach cable(copper), the copper cable is used to emulate the
10GBASE-KR scenario.
So, for XFI usage, there are two scenarios, one will use fiber cable,
another will use copper cable. For fiber cable, there is NO PHY, while
for copper cable, we need to use internal PHY which exist in Serdes to
do auto-negotiation and link training, which implemented in kernel.
We use hwconfig to define cable type for XFI, and fixup dtb based on the
cable type.
For copper cable, set below env in hwconfig:
fsl_10gkr_copper:<10g_mac_name>
the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2. The
four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports,
if a given 10G port will use the copper cable for 10GBASE-KR, set the
<10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be
assumed to be used for the port.
For ex. if four XFI ports will both use copper cable, the hwconfig
should contain:
fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm2_10g1,fm2_10g2
For fiber cable:
1. give PHY address to a XFI port, otherwise, the XFI ports will not be
available in U-boot, there is no PHY physically for XFI when using fiber
cable, this is just to make U-boot happy and we can use the XFI ports
in U-boot.
2. fixup dtb to use fixed-link in case of fiber cable which has no PHY.
Kernel requests that a MAC must have a PHY or fixed-link.
When using XFI protocol, the MAC 9/10 on FM1 should init as 10G interface.
Change serdes 2 protocol 56 to 55 which has same feature as 56 since 56
is not valid any longer.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031.
Add support for one FEC port initially.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6sxsabresd was not in the master branch when the conversion to the new Kconfig
style happened, so convert it now so that it can build again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Use the latest DDR initialization values suggested by the FSL hardware team.
While at it, add some comments for clarification.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently I don't have access to a mx31pdk board.
Magnus was the original maintainer of the board and accepted to take back
this role.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add deep sleep support in SPI/SD boot. The destination address
second stage uboot image is loaded to is changed because
currently this address will be used by kernel which means
we can't reserve it for resume.
Entry point to kernel is still placed in second stage uboot.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1042 has internal display interface unit (DIU) for driving video.
T1042RDB supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder
Chrontel, CH7301C encoder which is I2C programmable is used
as HDMI connector on T1042RDB.
This patch add support to
-enable Video interface for T1042RDB
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1042
-program HDMI encoder via I2C on board
This patch refer to the upstream diu patch
(337b0c52b3) for T1040qds.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[York Sun: resolve conflict and move changes to T104xRDB.h]
Reviewed-by: York Sun <yorksun@freescale.com>
The ch7301 encoder not only used in t1040qds platform, so we split
it for t1042rdb and LSx platform.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
It is redundant to use 'PFUZE100_PMIC' as the PMIC name because we already
know it is a PMIC.
Call it simply 'PFUZE100' instead.
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no need to keep iomuxc_base_regs structure as it serves the exact same
purpose of the iomuxc structure, which is to provide access to the GPR
registers.
The additional fields of iomuxc_base_regs are not used. Other advantage of
'iomuxc' is that it has a shorter name and the variable declarations can fit
into a single line.
So remove iomuxc_base_regs structure and use iomuxc instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
T4240 has 4 serdes, each serdes has 4k memory space, two PLLs.
We use PLL1CR0 to check the serdes reference clock.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
find_tlb_idx() is called in board_early_init_r() on multiple boards.
The return value is not checked before being used to disable a TLB.
In normal case the return value wouldn't be -1. In case of a mis-
configuration during porting to a new board, checking the return value
may be helpful to reveal some user errors.
Signed-off-by: York Sun <yorksun@freescale.com>
Since P1023RDS is no longer supported/manufactured by Freescale,
we clean up P1023RDS related code.
Since P1023RDB is still supported by Freescale,
we keep P1023RDB releated code.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The latest GCC is so clever that it reports more warnings
than old ones did:
------------------------------>8------------------------------
board/freescale/m5253demo/flash.c: In function 'flash_get_offsets':
board/freescale/m5253demo/flash.c:65:23: warning: iteration 2047u
invokes undefined behavior [-Waggressive-loop-optimizations]
info->start[k + 1] = info->start[k] + CONFIG_SYS_SST_SECTSZ;
^
board/freescale/m5253demo/flash.c:64:3: note: containing loop
for (k = 0, j = 0; j < CONFIG_SYS_SST_SECT; j++, k++) {
^
------------------------------8<------------------------------
The cause of the warning is like this:
The for statement iterates 2048 times in flash_get_offsets() func.
(Notice CONFIG_SYS_SST_SECT is defined as 2048)
The last iteration does
info->start[2048] = info->start[2047] + CONFIG_SYS_SST_SECTSZ;
causing an undefined behavior.
(Please note the array size of info->start is 2048.
CONFIG_SYS_MAX_FLASH_SECT is defined as 2048 for this board.)
This commit fixes that so as not to overrun the info->start array.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jason Jin <Jason.jin@freescale.com>
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
Two DDR controllers
UART2 is used as the console
IFC timing is tightened for speedy booting
Support DDR3 and DDR4 as separated targets
Management Complex (MC) is enabled
Support for GIC 500 (based on GICv3 arch)
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Fix the following warning messages:
In function 'flash_erase': 180:21:
warning: variable 'last' set but not used [-Wunused-but-set-variable]
In function 'write_buff': 322:10:
warning: variable 'port_width' set but not used [-Wunused-but-set-variable]
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Explain the necessary steps in order to boot from SPI NOR.
Based on a earlier submission from Mårten Wikman.
Signed-off-by: Mårten Wikman <marten.wikman@novia.fi>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add QSPI support for VF610TWR, such as clock and iomux.
Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Crossbars and IDT were not getting configured for Serdes2 protocol
0x9d for B4420.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
A-007186: SerDes PLL is calibrated at reset. It is possible
for jitter to increase and cause the PLL to unlock when the
temperature delta from the time the PLL is calibrated exceeds
+56C/-66C when using X VDD of 1.35 V (or +70C/-80C when using
XnVDD of 1.5 V). No issues are seen with LC VCO. The protocols
only using Ring VCOs are impacted.
Workaround:
For all 1.25/2.5/5 GHz protocols, use LC VCO instead of Ring
VCO, this need to use alternate serdes protocols. Alternate
option has the same functionality as the original option; the
only difference being LC VCO rather than Ring VCO.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
- add support for 2nd DIMM slot.
- make it work with DIMM which is less than 2GB.
Verified with two 2GB UDIMM MT9JSF25672AZ-2G1K1 in two DIMM slots.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
A-007186: SerDes PLL is calibrated at reset. It is possible for jitter to
increase and cause the PLL to unlock when the temperature delta from the
time the PLL is calibrated exceeds +56C/-66C when using X VDD of 1.35 V
(or +70C/-80C when using XnVDD of 1.5 V). No issues are seen with LC
VCO. Only the protocols using Ring VCOs are impacted.
Workaround:
For all 1.25/2.5/5 GHz protocols, use LC VCO instead of Ring VCO, this need
to use alternate serdes protocols. The alternate option has the same
functionality as the original option; the only difference being LC VCO
rather than Ring VCO.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As errata A-007186, we need to use the alternate serdes
protocol instead of those impacted protocols.
- add support for serdes protocols: 0x1b, 0x50, 0x5e,
0x64, 0x6a, 0xd2, 0x67, 0x70.
- update t2080_rcw.cfg to adapt to new rcw_66_15 for
t2080qds and t2080rdb.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
Set DDR_SEL_PAD_CONTR register explicitly to DDR3 which solves RAM
issues with newer silicon (1.1). This register was added in revision
4 of the Vybrid Reference Manual.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
In the earlier patches, the SPL/TPL fraamework was introduced.
For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The
SPL was loaded by the code from the internal on-chip ROM. The SPL initializes
the DDR according to the SPD and loads the final uboot image into DDR, then
jump to the DDR to begin execution.
For NAND booting way, the nand SPL has size limitation on some board(e.g.
P1010RDB), it can not be more than 4KB, we can call it "minimal SPL", So the
dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is
loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD
and loads the final uboot image into DDR,then jump to the DDR to begin execution.
This patch enabled SPL/TPL for P1_P2_RDB to support starting from NAND/SD/SPI
flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL.
Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to
execute, so the section .resetvec is no longer needed.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T104xrdb has several sleep management signals that are used for deep
sleep. They are enabled by OS to enter deep sleep and should be
disabled by u-boot when cores wake up.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
According to AN3638, CRC of NXID v1 is at the end of the
256-byte I2C memory. The wrong CRC32 offset prevents Uboot
from reading system information from EEPROM. No NXID v0 is
being used on Freescale boards.
Signed-off-by: Ebony Zhu <b45385@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Exception handling is basically identical for all ARM targets.
Factorize it out of the various start.S files and into a
single vectors.S file, and adjust linker scripts accordingly.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
The return value has not been checked by its caller, until recent change
of using generic board architecture. The error of this function is not
critical enough to hang the system. Printing the warning message is enough
to catch user's attention. U-boot should continue to boot to give user
a chance to fix the EEPROM. Chaning the return value to 0 to avoid hanging
in the board_init_r().
Signed-off-by: York Sun <yorksun@freescale.com>
We only need u-boot to bother about a single core in the QEMU machine.
Everything that would require additional knowledge of more cores gets
handled by QEMU and passed straight into the payload we execute.
Because of this setup, it would be counterproductive to enable SMP support
in u-boot. We would have to rip CPUs out of already existing spin tables
and respin them from u-boot. It would be a pretty big mess.
So only assume we have a single core. This fixes errors about CONFIG_MP
being disabled.
Signed-off-by: Alexander Graf <agraf@suse.de>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
B4860QDS has a PowerOne ZM7300 programmable digital Power
Manager which is programmed as per the value read from
the fuses.
Reference for this code is taken from t4qds VID implementation.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Adds Support for PowerOne ZM7300 voltage regulator.
This device is available on some Freescale Boards like B4860QDS
and has to be programmed to adjust the voltage on the board.
The device is accessible via I2C interface.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
mx6slevk has a m25p32 SPI NOR flash connected to ESCSPI port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Add support of 2 stage NAND/SD boot loader using SPL framework.
PBL initialise the internal SRAM and copy SPL, this further
initialise DDR using SPD and environment and copy u-boot from
NAND/SD to DDR, finally SPL transfer control to u-boot.
NOR uses CS1 instead of CS2 when NAND boot, fix it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
- update readme.
- add CONFIG_SYS_CORTINA_FW_IN_* for loading Cortina PHY CS4315
ucode from NOR/NAND/SPI/SD/REMOTE.
- update cpld vbank with SW3[5:7]=000 as default vbank0 instead of
previous SW3[5:7]=111 as default vbank.
- fix CONFIG_SYS_I2C_EEPROM_ADDR_LEN to 2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768K) from SPI/SD/NAND to DDR, finally SPL transfers control
to u-boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768 KB) from SPI/SD/NAND to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix boards.cfg for T2081QDS_SDCARD and _SPIFLASH]
Reviewed-by: York Sun <yorksun@freescale.com>
There should be a break for case PHY_INTERFACE_MODE_SGMII, otherwise it
will fall into case PHY_INTERFACE_MODE_RGMII.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2 stage NAND, SD, SPI boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040RDB and T1042RDB_PI has CPLD. Here CPLD controls board mux/features.
This support of CPLD includes
- files and register defintion
- Commands to swtich alternate bank and default bank
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040QDS_D4 is a variant of T1040QDS, with additional circuit to support
DDR4 memory. Tested with MTA9ASF51272AZ-2G1AYESZG.
Signed-off-by: York Sun <yorksun@freescale.com>
The MDC generate by default value of MDIO_CLK_DIV is too high i.e. higher
than 2.5 MHZ. It violates the IEEE specs.
So Slow MDC clock to comply IEEE specs
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For KVM we have a special PV machine type called "ppce500". This machine
is inspired by the MPC8544DS board, but implements a lot less features
than that one.
It also provides more PCI slots and is supposed to be enumerated by
device tree only.
This patch adds support for the generic ppce500 machine and tries to
rely solely on device tree for device enumeration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The DRAM size can be easily detected at runtime on i.MX53. Implement
such detection on MX53QSB and adjust the rest of the macros accordingly
to use the detected values.
An important thing to note here is that we had to override the function
for trimming the effective DRAM address, get_effective_memsize(). That
is because the function uses CONFIG_MAX_MEM_MAPPED as the upper bound of
the available DRAM and we don't have gd->bd->bi_dram[0].size set up at
the time the function is called, thus we cannot put this into the macro
CONFIG_MAX_MEM_MAPPED . Instead, we use custom override where we use the
size of the first DRAM block which we just detected.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Add support for PCIe on MX6 SabreSDP board and enable the support
in the config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Liu Ying <Ying.Liu@freescale.com>
CONFIG_SYS_HZ must be always 1000, but M5271EVB.h defines it
as 1000000 and idmr.h defines it as (50000000 / 64).
When compiling these two boards, a warning message is displayed:
time.c:14:2: warning: #warning "CONFIG_SYS_HZ must be 1000
and should not be defined by platforms" [-Wcpp]
There are no board maintainers for them so this commit just
deletes them.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jason Jin <Jason.jin@freescale.com>
Update following DDR related settings for T1040RDB, T1042RDB_PI
-Correct number of chip selects to two as t1040 supports
two Chip selects.
-Update board_specific_parameters udimm structure with settings
derived via calibration.
-Update ddr_raw_timing sructure corresponding to DIMM.
-Set ODT to off. Typically on FSL board, ODT is set to 75 ohm,
but on T104xRDB, on setting this , DDR instability is observed.
Board-level debugging is in progress.
Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
T1040 has internal display interface unit (DIU) for driving video.
T1040QDS supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder
Chrontel, CH7301C encoder which is I2C programmable is used as
HDMI connector on T1040QDS.
This patch add support to
-enable Video interface for T1040QDS
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1040
-program HDMI encoder via I2C on board
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC.
It works in two mode: standalone mode and PCIe endpoint mode.
T2080PCIe-RDB Feature Overview
------------------------------
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
DDR Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LP devices
- 72bit 4GB DDR3-LP SODIMM in slot
Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Two 10Gbps SFP+ ports on-board
- Two 10Gbps Base-T ports on-board
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes 16 lanes configuration:
- SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10)
- SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
- SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3)
- SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2)
- SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2)
- SerDes-2 Lane G-H: to SATA1 & SATA2
IFC/Local Bus:
- NOR: 128MB 16-bit NOR flash
- NAND: 512MB 8-bit NAND flash
- CPLD: for system controlling with programable header on-board
eSPI:
- 64MB N25Q512 SPI flash
USB:
- Two USB2.0 ports with internal PHY (both Type-A)
PCIe:
- One PCIe x4 gold-finger
- One PCIe x4 connector
- One PCIe x2 end-point device (C293 Crypto co-processor)
SATA:
- Two SATA 2.0 ports on-board
SDHC:
- support a TF-card on-board
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Change QIXIS timing parameter CONFIG_SYS_CS3_FTIM2 to 8 from 0.
Fix EMI2 for t2080qds, which was caused by adding t2081qds.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384)
and at cold temperatures(A006475), workaround recalibrate the
PLLs with some SerDes configuration
Both these errata are only applicable for b4 rev1.
So, make workaround for these errata conditional,
depending upon soc version.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Change setting of SerDes2 refclk2 to have the default value as it is
coming on board that is 156.25MHz, for XFI to work.
Also change PLL_NUM variable to the one defined in config_mpc85xx.h
for B4860 and B4420.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On B4860 and B4420, some serdes protocols can be used with LC VCO as
well as Ring VCO options.
Addded Alternate options with LC VCO for such protocols.
For example protocol 0x2a on srds 1 becomes 0x29 if it is LC VCO.
The alternate option has the same functionality as the original option;
the only difference being LC VCO rather than Ring VCO.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1) SerDes2 Refclks have been set properly to make
PCIe SATA to work as it work on SerDes refclk of 100MHz
2) Mask the SerDes's device reset request before changing
the Refclks for SerDes1 and SerDes2 for PLL locks to
happen properly, device reset request bit unmasked
after SerDes refclks configuration
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1) Add new SerDes1 protocols having Aurora in them
2) Add VSC cross point connections for Aurora to work with
CPRI and SGMIIs
3) Configure VSC crossbar switch to connect SerDes1
lanes to aurora on board, by checking SerDes1 protocols
4) SerDes1 Refclks have been set properly to make
Aurora, CPRI and SGMIIs to work together properly
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
This prevents references to _end from generating absolute
relocation records.
This change is binary invariant for ARM targets.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
In the previous patches, we introduced the SPL/TPL fraamework.
For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The
SPL was loaded by the code from the internal on-chip ROM. The SPL initializes
the DDR according to the SPD and loads the final uboot image into DDR, then
jump to the DDR to begin execution.
For NAND booting way, the nand SPL has size limitation on some board(e.g.
P1010RDB), it can not be more than 8KB, we can call it "minimal SPL", So the
dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is
loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD
and loads the final uboot image into DDR,then jump to the DDR to begin execution.
This patch enabled SPL/TPL for P1010RDB to support starting from NAND/SD/SPI
flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL.
Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to
execute, so the section .resetvec is no longer needed.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2081 QDS is a high-performance computing evaluation, development and
test platform supporting the T2081 QorIQ Power Architecture processor.
T2081QDS board Overview
-----------------------
- T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
- 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC)
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving
- Ethernet interfaces:
- Two on-board 10M/100M/1G bps RGMII ports
- Two 10Gbps XFI with on-board SFP+ cage
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
- Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- SerDes:
- 8 lanes up to 10.3125GHz
- Supports SGMII, HiGig, XFI, XAUI and Aurora debug,
- IFC:
- 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
- USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- PCIe:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- eSDHC:
- Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and
voltage translators
- I2C:
- Four I2C controllers.
- UART:
- Dual 4-pins UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This function has been around for powerpc. It is used for systems with
memory more than CONFIG_MAX_MEM_MAPPED. In case of non-contiguous memory,
this feature can limit U-boot to one block without going over the limit.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Conflicts:
Makefile
drivers/net/npe/Makefile
These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
- When CONFIG_DISPLAY_CPUINFO is not enabled,
print_cpuinfo() should be defined as an empty function
in a header, include/common.h
- Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
from caller, common/board_f.c and arch/arm/lib/board.c
- Remove redundant prototypes in arch/arm/lib/board.c,
arch/arm/include/asm/arch-am33x/sys_proto.h and
board/nokia/rx51/rx51.h, keeping the one in include/common.h
- Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
where it is missing
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
We are going to switch over to Kbuild in upcoming commits.
Each makefile must have non-empty obj- or obj-y
to generate built-in.o on Kbuild.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This covers only non-L2 switch ethernet interfaces i.e.
RGMII and SGMII interface for both T1040RDB and T1042RDB_PI
T1040RDB is configured as serdes protocol 0x66 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
1 SGMII on DTSEC3
T1042RDB_PI is configured as serdes protocol 0x06 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: Minor change in commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
Due to increased size of u-boot, FMAN ucode start address has been shifted
by 256KB causing a overlap with rootfs start address.
Update rootfs start address to reflect correct memory map.
Also fix minor typo in README
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On BSC9131, BSC9132, P1010 : For High Capacity SD Cards (> 2 GBytes), the
32-bit source address specifies the memory address in block address
format. Block length is fixed to 512 bytes as per the SD High Capacity
specification. So we need to convert the block address format
to byte address format to calculate the envaddr.
If there is no enough space for environment variables or envaddr
is larger than 4GiB, we relocate the envaddr to 0x400. The address
relocated is in the front of the first partition that is assigned
for sdboot only.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
u-boot binary size for Freescale mpc85xx platforms is 512KB.
This has been reached to upper limit for some of the platforms causig
linker error.
So, Increase the u-boot binary size to 768KB.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
- Optimize UDIMM parameters for whole range from 1500MT/s to 2140MT/s.
- Remove unused patameters: 'cpo', 'wrdata delay', '2T', which are
unrelated to DDR3/3L.
Tested with UDIMM 9JSF25672AZ-2G1K1 and verified speed 1200/1866/2133MT/s.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Using the TPL/SPL method to booting from 8k page NAND flash.
- Add 256kB size SRAM tlb for second step booting;
- Add spl.c for TPL image boot;
- Add spl_minimal.c for minimal SPL image;
- Add C29XPCIE_NAND configure;
- Modify C29XPCIE.h for nand config and enviroment;
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
- add more serdes protocols support.
- fix some serdes lanes route.
- fix SGMII doesn't work and incorrect mdio display for XFI when serdes 0x6d.
- correct boot location info for SD/SPI boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update following DDR related settings for T1040QDS
-Correct number of chip selects to two as t1040qds supports
two Chip selects.
-Update board_specific_parameters udimm structure with settings
derived via calibration.
-Reduced I2C speed to 50KHz as DDR-SPD does not get reliably
read at 400KHz.
Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 833MT/s, 1333MT/s and
1600MT/s.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Provide an argument to enable_fec_anatop_clock() to specify the clock frequency
that will be generated.
No changes are made to mx6slevk, which uses the default 50MHz fec clock.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.
Conflicts:
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
CONFIG_SPL_NAND_MINIMAL should not be used as it was defined for temporary
review purpose.
So, use CONFIG_SPL_NAND_BOOT config.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
mx6sabresd boards have a 18-bit LVDS data width and the correct color format
is RGB666.
Suggested-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
HSYNC, VSYNC and DISP_CLK are very useful display signals for debugging.
Configure them as active pins.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Align with the context to use readl() to read the CCM_CCGR3
register with memory barrier instead of __raw_readl().
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
This allows the use of either or both declarations from
the files mx6q_pins.h and mx6dl_pins.h.
All board files should include <asm/arch/mx6-pins.h>
with one of the following defined in boards.cfg
MX6Q - for boards targeting i.MX6Q or i.MX6D
MX6DL - for boards targeting i.MX6DL
MX6S - for boards targeting i.MX6S
MX6QDL - for boards that support any of the above with
run-time detection
Pad declarations will be MX6_PAD_x for single-variant boards
and MX6Q_PAD_x and MX6DL_PAD_x for boards supporting both
processor classes.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The pmic_init() function has the I2C or SPI bus number that is connected to the
PMIC.
Instead of passing I2C_PMIC, explicitly pass the I2C bus number via I2C_x
definition.
The motivation for doing this is to avoid people just doing a copy and paste
of I2C_PMIC into their board file when another I2C bus is actually used to
interface to their PMIC.
This also makes more obvious which is the I2C bus connected to the PMIC, without
having to search in the source code for the meaning of the 'I2C_PMIC' number.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add the __iomem address space marker for the tsec pointers
to struct tsec_mii_mng memory mapped register regions.
This solves the sparse warnings for mixig normal pointers with
__iomem pointers for tsec.
p1_p2_rdb_pc.c:373:24: warning: incorrect type in assignment (different
address spaces)
p1_p2_rdb_pc.c:373:24: expected struct tsec_mii_mng [noderef]
<asn:2>*regs
p1_p2_rdb_pc.c:373:24: got struct tsec_mii_mng *<noident>
Use TSEC_GET_MDIO_REGS_BASE() for the remaining mdio 'regs'
initializations to remove the __iomem warnings and for consistency.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Current LDS files /DISCARD/ a lot of sections when linking ELF
files, causing diagnostic tools such as readelf or objdump to
produce partial output. Keep all section at link stage, filter
only at objcopy time so that .bin remains minimal.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Currently, there is only one EEPROM on c29xpcie board which is AT24C1024.
We program the SPD data at beginning of the AT24C1024.But the AT24C1024
has a 16-bit sub-address mode. This patch is tomake it work when getting
SPD in a 16-bit sub-address EEPROM.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
mx6sabre board has a m25p32 SPI NOR connected to ECSPI1 port.
Add support for it.
This patch allows the SPI NOR flash to be succesfully detected:
=> sf probe
SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently HDMI splash screen is selected by default on mx6sabresd boards.
As LVDS is also enabled, this causes incorrect colors to be displayed im the
LVDS panel.
Fix this by selecting the LVDS panel as the default splash output and only keep
HDMI or LVDS turned on at the same time.
Acked-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On mx31pdk board the PMIC is connected via SPI interface, so it does not make
sense to pass I2C_PMIC into the pmic_init() interface.
Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On mx51evk board the PMIC is connected via SPI interface, so it does not make
sense to pass I2C_PMIC into the pmic_init() interface.
Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add the default RCW(SerDes 0x66_0x16) and PBI configure file for
T2080QDS board, so we can use PBL tool to generate the ramboot
image to support boot from NAND/SPI/SD.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
The T2080QDS is a high-performance computing evaluation, development and
test platform supporting the T2080 QorIQ Power Architecture processor.
T2080QDS feature overview
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LV devices
- Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/SDHC/SDXC/eMMC Card
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
Debug Features:
- Support Legacy, COP/JTAG, Aurora, Event and EVT
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: removed Makefile blank line at EOF,
fix conflicts with moving DDR driver]
Acked-by: York Sun <yorksun@freescale.com>
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/misc
and fix the header file includes.
Signed-off-by: York Sun <yorksun@freescale.com>
Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
Board config.mk do not need to add -DCONFIG_SYS_TEXT_BASE
to CPPFLAGS because the top level config.mk does instead.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
T1042RDB_PI is Freescale Reference Design Board supporting the T1042
QorIQ Power Architecture™ processor. T1042 is a reduced personality
of T1040 SoC without Integrated 8-port Gigabit. The board is designed
with low power features targeted for Printing Image Market.
T1042RDB_PI is similar to T1040RDB board with few differences like
it has video interface, supports T1042 personality
T1042RDB_PI board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Two on-board RGMII 10/100/1G ethernet ports.
- SERDES Connections, 8 lanes supporting:
— PCI
— SATA 2.0
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Video
- DIU supports video at up to 1280x1024x32bpp
- HDMI connector
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Device connected: EEPROM, thermal monitor, VID controller, RTC
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
- Remove duplicate doc/README.p1010rdb
- Rename README to README.P1010RDB-PA
- Add new README.P1010RDB-PB
P1010RDB-PB is a variation of previous P1010RDB-PA board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Use a default RCW of protocol 0x66.
A PBI configure file which uses CPC as 256KB SRAM. It can be used by
PBL tool on T1040 to build a pbl boot image.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Since the titanium board is not a Freescale board, move its
BSP code from the freescale board directory to the newly created
barco board directory.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
This allows to share some common code for the boards that use a corenet
base SoC.
Two different versions of the function are available in
fsl_corenet_serdes.c and fsl_corenet2_serdes.c files.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix t1040qds.c]
Acked-by: York Sun <yorksun@freescale.com>
c29xpcie REV_A board DDR ECC chip has bad impedance in hardware,
force that kind of board to be DDR ECC off when booting.
Other version board config ECC on/off by hwconfig=fsl_ddr:ecc=on
in uboot enviroment.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
- Rename old P1010RDB board as P1010RDB-PA.
- Add support for new P1010RDB-PB board.
- Some optimization.
For more details, see board/freescale/p1010rdb/README.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix conflicts in boards.cfg]
Acked-by: York Sun <yorksun@freescale.com>
Since pins multiplexing, SDHC shares signals with IFC, with this patch:
To enable SDHC in case of NOR/NAND/SPI boot
a) For temporary use case in runtime without reboot system
run 'mux sdhc' in u-boot to validate SDHC with invalidating IFC.
b) For long-term use case
set 'esdhc' in hwconfig and save it.
To enable IFC in case of SD boot
a) For temporary use case in runtime without reboot system
run 'mux ifc' in u-boot to validate IFC with invalidating SDHC.
b) For long-term use case
set 'ifc' in hwconfig and save it.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Some boards use System EEPROM with 128-bytes instead of 256-bytes.
Since we regard 256-bytes EEPROM as standard EEPROM with default
value for MAX_NUM_PORTS. For those non-256-bytes EEPROM, we can
redefine MAX_NUM_PORTS in board-specific file to override the
default MAX_NUM_PORTS.
This patch doesn't impact on previous existing boards.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
T1040QDS is a high-performance computing evaluation, development and
test platform supporting the T1040 QorIQ Power Architecture™ processor.
T1040QDS board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch
- Four 1 Gbps Ethernet controllers
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: fix conflict in boards.cfg]
Acked-by-by: York Sun <yorksun@freescale.com>
Some DDR related structures present in fsl_ddr_dimm_params.h, fsl_ddr_sdram.h, ddr_spd.h
has various parameters with embedded acronyms capitalized that trigger the CamelCase
warning in checkpatch.pl
Convert those variable names to smallcase naming convention and modify all files
which are using these structures with modified structures.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Use a default RCW of protocol 0x2A_0x98, and a PBI configure file which
uses CPC1 as 512KB SRAM, then PBL tool can be used on B4860 to build a
pbl boot image.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Default configuration has been changed, the most important one is DDR
ref_clock which is changed from 66.67MHz to 133.33MHz. so the ratio need to
change from 24x to 12x to keep the DDR frequency. There are also some
other optimise to align with default configuration.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Fix PHY addresses for QSGMII Riser Card working in
SGMII mode on board P3041/P5020/P4080/P5040/B4860.
QSGMII Riser Card can work in SGMII mode, but
having the different PHY addresses.
So the following steps should be done:
1. Confirm whether QSGMII Riser Card is used.
2. If yes, set the proper PHY address.
Generally, the function is_qsgmii_riser_card() is
for step 1, and set_sgmii_phy() for step 2.
However, there are still some special situations,
take P5040 and B4860 as examples, the PHY addresses
need to be changed when serdes protocol is changed,
so it is necessary to confirm the protocol before
setting PHY addresses.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
SGMII5/6 and SGMII7/8 are not on the same slot on P5040
according to the serdes protocol.
So it is not proper to organize SGMII5/6 and SGMII7/8
on one bus and SGMII5/6 can't work.
So a new bus SUPER_HYDRA_FM3_SGMII_MDIO is added for
SGMII5/6
Signed-off-by: Zhao Qiang <B45475@freescale.com>
DDR parameters clk_adjust were changed. This can make the DDR
run more stable. The new value were gotten by the DDR testing
tool.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
If smc911x_initialize() fails we should return the error immediately.
While at it, also check the error from cpu_eth_init().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Currently board_eth_init() always return 0, but we should propagate the error
when cpu_eth_init() fails.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently board_eth_init() always return 0, but we should propagate the error
when cpu_eth_init() fails.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If a HDMI cable is not connected, the following message is seen on boot:
CPU: Freescale i.MX6Q rev1.1 at 792 MHz
Reset cause: POR
Board: MX6-SabreSD
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
No panel detected: default to HDMI
unsupported panel HDMI
Reset the 'i' variable to fix the 'unsupported panel' message.
This follows the same idea of commit 47ac53d7ae (imx: nitrogen6x/mx6qsabrelite:
Fix bug in board_video_skip).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Since commit d9b894603 (mx6sabresd: Add LVDS splash screen support) the
following hang happens if the HDMI cable is not connected or the 'panel'
variable is not set:
U-Boot 2013.10-rc2-12978-g47ac53d-dirty (Sep 11 2013 - 15:07:38)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6-SabreSD
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
...
Provide a check to 'dev->detect' in order to prevent the hang.
Reported-by: Pardeep Kumar Singla <b45784@freescale.com>
Suggested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fix various misspellings of things like "environment", "kernel",
"default" and "volatile", and throw in a couple grammar fixes.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
mx6sabresd boards can be connected to a Hannstar XGA LVDS panel.
Add support for displaying U-boot splashscreen on it.
By default, HDMI splash is selected.
In order to use splash via LVDS, do the following in the U-boot prompt:
setenv panel Hannstar-XGA
save
and reboot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Make sure value in register r0 and r1 is preserved and passed to
the board_init_ll() and mxs_common_spl_init() where it can be
processed further. The value in r0 can be configured during the
BootStream generation to arbitary value, r1 contains pointer to
return value from CALL'd function.
This patch also clears the value in r0 before returning to BootROM
to make sure the BootROM is not confused by this value.
Finally, this patch cleans up some comments in the start.S file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
- Added section "u_boot_list" in arch/powerpc/cpu/mpc85xx/u-boot-spl.lds
- Use the function i2c_init_all instead of i2c_init
Signed-off-by: Ying Zhang <b40530@freescale.com>
There was a bug for calculating ddr_freq_mhz,
it should be divided by 1000000 rather than 0x1000000.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
When using QSGMII protocols, the first lane and third lane on each slot
need to be swapped.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Since the parameters need to be modified according to different Serdes
protocols at runtime, the const will block this. Also remove const from
arrays define used by vsc3316_config.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c
Signed-off-by: York Sun <yorksun@freescale.com>
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions.
because of this code checkpatch script generates "WARNING: Avoid CamelCase".
Convert variables name to normal naming convention and modify board, driver
files with updated the new structure.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
TPL is introduced in the patch "NAND: TPL : introduce the TPL
based on the SPL", here enable TPL for p1022ds nand boot.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.
Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h
Signed-off-by: Tom Rini <trini@ti.com>
Fix the license header introduced by the following patches
Add TWR-P10xx board support
Add T4240EMU target
IDT8T49N222A configuration code
Add C29x SoC support
Add support for C29XPCIE board
Signed-off-by: York Sun <yorksun@freescale.com>
C29XPCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module. It
includes C293PCIE board, C293PCIE board and C291PCIE board.
- 512KB platform SRAM in addition to 512K L2 Cache/SRAM
- 512MB soldered DDR3 32bit memory
- CPLD System Logic
- 64MB x16 NOR flash and 4GB x8 NAND flash
- 16MB SPI flash
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Singed-off-by: Po Liu <Po.Liu@freescale.com>
[yorksun: Fixup include/configs/C29XPCIE.h]
Signed-off-by: York Sun <yorksun@freescale.com>
1) Add support in B4860 board files for using IDT driver where
IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer
that generate different refclks for SerDes modules, used this driver
for reconfiguring SerDes1 Refclks(based on SerDes1 protocols)
for CPRI to work. CPRI works on 122.88MHz and default refclks coming
on board are not suitable for it
2) Move SerDes1 refclk1 source selection from eth_b4860qds.c file
to b4860qds board file, as SerDes1 Refclk1 would come from
PHY MUX in case of certain protocols, that have been checked here.
This change would make on board SGMIIs to work
3) Add I2C addresses for IDT8T49N222A devices in board/include file
4) Add define for PCA-I2C bus multiplexer, on which IDT devices exist
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Add code for configuring IDT8T49N222A device for various output refclks
- The IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer with
alarm and monitoring functions suitable for networking and
communications applications. It is able to generate wide range of output
frequencies.
- In B4860QDS, it has been used to generate different refclks to SerDes modules
- Programming of these devices are performed by I2C interface.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
BSC9132 SoC has two separate DDR controllers for PowerPC side and DSP side
DDR. They are mapped to PowerPC and DSP CCSR space respectively.
BSC9132QDS has two on-board MC34716EP DDR3 memory one connected to PowerPC
and other to DSP side controller.
Configure DSP DDR controller similar to PowerPC side DDR controller as
memories are exactly similar.
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a
integrated device that contains two powerpc e500v2 cores and two DSP
starcores.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 and M3 memory
-Creating LAW for 1GB DDR which is connected exclusively to DSP-cores
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Add new board p1020RDB-PD. P1020RDB-PD board was update from P1020RDB.
DDR changed from DDR2 1G to DDR3 2G.
NAND: 128 MiB
Flash: 64 MiB
Also change P1020RDB to P1020RDB-PC to distinguish from P1020RDB board.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
JEDEC spec requires the clocks to be stable before deasserting reset
signal for RDIMMs. Clocks start when any chip select is enabled and
clock control register is set. This patch also adds the interface to
toggle memory reset signal if needed by the boards.
Signed-off-by: York Sun <yorksun@freescale.com>
RDIMM has different timing. Tested RDIMM is MT18JSF1G72PDZ-1G9E1 for
dual rank. Single- and quad-rank are not tested due to availability.
Signed-off-by: York Sun <yorksun@freescale.com>
Add emulator support for T4240. Emulator has limited peripherals and
interfaces. Difference between emulator and T4240QDS includes:
ECC for DDR is disabled due the procedure to load images
No board FPGA (QIXIS)
NOR flash has 32-bit port for higher loading speed
IFC and I2C timing don't really matter, so set them fast
No ethernet
Signed-off-by: York Sun <yorksun@freescale.com>
TWR-P1025 Specification:
-----------------------
Memory subsystem:
512MB DDR3 (on board DDR)
64Mbyte 16bit NOR flash
One microSD Card slot
Ethernet:
eTSEC1: Connected to Atheros AR8035 GETH PHY
eTSEC3: Connected to Atheros AR8035 GETH PHY
UART:
Two UARTs are routed to the FDTI dual USB to RS232 convertor
USB: Two USB2.0 Type A ports
I2C:
AT24C01B 1K Board EEPROM (8 bit address)
QUICC Engine:
Connected to DP83849i PHY supply two 10/100M ethernet ports
QE UART for RS485 or RS232
PCIE:
One mini-PCIE slot
Signed-off-by: Michael Johnston <michael.johnston@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
[yorksun: Fixup include/configs/p1_twr.h]
Signed-off-by: York Sun <yorksun@freescale.com>
mx6qsabrelite and nitrogen6q boards are hardware compatible, so let's avoid the
code duplication and only use the nitrogen6x source code to make board code
maintainance easier.
Tested booting a mainline device tree kernel on a mx6qsabrelite board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Fix:
mpc8323erdb.c: In function 'mac_read_from_eeprom':
mpc8323erdb.c:198:3: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Timur Tabi <timur@tabi.org>
cc: Kim Phillips <kim.phillips@freescale.com>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
The SabreSD platform is available with i.MX6Q or i.MX6DL. This patch adds the
support of the i.MX6DL. The config file and the board directory are renamed
to remove the reference to the MX6Q.
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
This change is only done where needed: some linker
scripts may contain relocation symbols yet remain
unchanged.
__rel_dyn_start and __rel_dyn_end each requires
its own output section; putting them in relocation
sections changes their flags and breaks relocation.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This change is only done where needed: some linker
scripts may contain __image_copy_{start,end} yet
remain unchanged.
Also, __image_copy_end needs its own section; putting
it in relocation sections changes their flags and makes
relocation break.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Discard all .dynsym sections from linker scripts
Remove all __dynsym_start definitions from linker scripts
Remove all __dynsym_start references from the codebase
Note: this touches include/asm-generic/sections.h, which
is not ARM-specific, but actual uses of __dynsym_start
are only in ARM, so this patch can safely go through
the ARM repository.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
"pixis_reset help" command prints the message without a new line "\n",
which makes the prompt on the same line.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
PCIe TLB should be created with CONFIG_PCI defined
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a T4 board boots from SRIO or PCIE, it needs to finish these processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
e500v2 processor does not support 8K page size TLB entries.
So create new TLB entry only during NAND SPL boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB has 1GB DDR.
Out of this, only 880MB is passed on to Linux via bootm_size.
Remaining
-16MB is reserved for PowerPC-DSP shared control area
-128MB is reserved for DSP private area.
Also 256MB, out of this 880MB is required for data communication between
PowerPC and DSP core.
For this bootargs are modified to pass parameter to create 1 hugetlb
page of 256MB via default_hugepagesz, hugepagesz and hugepages
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB is a Freescale Reference Design Board for
BSC9131 SoC which is a integrated device that contains
one powerpc e500v2 core and one DSP starcore.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 memory
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB supports Sysclk
-66MHz if jumper J16 is close (default state)
-100MHz if jumper J16 is open
Add targets
-BSC9131RDB_NAND_SYSCLK100 : for NAND boot at Sysclk 100MHz
-BSC9131RDB_SPIFLASH_SYSCLK100: for SPI boot at Sysclk 100MHz
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Linker script is not able find start.o binary. So add its absolute path in
u-boot-spl.lds. This change is similar to u-boot-nand.lds
common/Makefile: Avoid compiling unnecssary files
fsl_ifc_spl.c : It is is responsible for reading u-boot binary from
NAND flash and copying into DDR. It also transfer control from NAND SPL
to u-boot image present in DDR.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
No need to use the 'status' variable, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
The number of gpio signal is packed inside CONFIG_SF_DEFAULT_CS macro
(shifted and or'ed with chip select), so it's incorrect to pass
that macro directly as an argument to gpio_direction_output() call.
Also, SPI driver sets the direction and initial value of a gpio,
used as a chip select signal, before any actual activity happens
on the bus.
So, it is safe to just remove the gpio_direction_output call,
that works incorrectly, thus making no effect, anyway.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
There are 3 IO expanders on the mx6qsabreauto all reset by the
same GPIO, just set it to high to use the IO.
Signed-off-by: Renato Frias <b13784@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add i2c2 and 3 to mx6qsabreauto board, i2c3 is multiplexed
use gpio to set steering.
Signed-off-by: Renato Frias <b13784@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
VF610TWR is a board based on Vybrid VF610 SoC.
This patch adds basic support for Vybrid VF610TWR board.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Current driver of p5040 assumes 10G port follows 1G port DTSEC5 in
eth port enum structure, it will assign mdio mux depend on this assumption.
This is not true with Fman V3, which added more 1G ports after port DTSEC5
in eth port enum structure, then 10G ports on p5040 will have wrong mdio mux.
So we use dynamic index for 10G ports instead of hardcoded enum value
when doing mdio mux for 10G ports.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
PC board has different serdes clock setting with PB board, it uses same
serdes frequency setting on bank2 as on bank1. PC board can be distingushed
from PB board by checking CPLD version, if running on PC board, then fix
the serdes reference clock frequency of bank2.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Crossbar switches were wrongly programmed to
route the CPRI lanes to SFP as the connectivity table
was not correct.
Modified it correctly for SFPs connections.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
QSGMII card has different PHY address against previous SGMII card.
We check the type of card in slots and set correct PHY address to
avoid complainning "PHY reset timed out" during u-boot booting up.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
SW7[4] is the new bit which controls the mapping of eMMC vs SDHC.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
- Added SERDES2 PRTCLs = 0x98, 0x9E
- Default Phy Addresses for Teranetics PHY on XAUI card
The PHY addresses of Teranetics PHY on XAUI riser card are assigned
based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on
AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1
and slot2
- Configure MDIO for 10Gig Mac
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Debug trace buffers are memory mapped in DCSR space beyond 4M.
Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Provided a default RCW for P5040, then it can use PBL to build
ramboot image.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Use QIXIS measurement registers to obtain sysclk and ddr clock. This
allows using non-standard clock speeds, set by directly writing to
clock chip or store the values in qixis clock data eeprom.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
QIXIS includes frequency measurement functions for each major processor
clock input. After reset (and after clocks are stable), QIXIS measures
the clocks against a reference frequency and stores the results in
CLK_FREQ registers. A base register supplies a multiplier which allows
directly obtaining the measured value, without requiring knowledge of
the target system or QIXIS core frequency.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Added a default RCW(1_28_6_12) and PBI configure file for T4240, so it can use
PBL tool to produce the ramboot image.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Allow VDD voltage overriding with a command. This is an add-on feasture of
VID. To override VDD, use command vdd_override with the value of voltage
in mV, for example
vdd_override <voltage in mV, eg. 1050>
The above example will set the VDD to 1.050 volt. Any wrong value out of
range of 0.8188 to 1.2125 volt or invalid string is ignored.
In addition to the command, if overriding VDD is needed earlier in booting
process, save an variable and reboot:
setenv t4240qds_vdd_mv <voltage in mV>
saveenv
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Print more detail information including core voltage, RCW source, switch
settings, etc. with bdinfo command.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
QSGMII card assumed to be used by default, but if SGMII card is used,
it will use different PHY address, but we don't know which card is used
until we access PHY on the card. So we check the card type slot by slot,
if we can read a PHY ID by reading a SGMII PHY address on a slot, then
the slot must have a SGMII card pluged, we mark all ports on that slot,
and fix dts to use the SGMII card PHY address when doing dts fixup
for the marked ports.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Only clear IRE bit in qixis brdcfg5 register and keep other bits
unchanged.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4860QDS requires DDRC2 has 0 as base address and DDRC1 has higher address.
This is the requirement for DSP cores to run in 32-bit address space.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Use QSGMII card PHY address as default SGMII card PHY address, QSGMII card
PHY address is variable depends on different slot.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1, Implemented board_ft_fman_fixup_port() to fix port for kernel.
2, Implemented fdt_fixup_board_enet() to fix node status of different
slots and interfaces.
3, Adding detection of slot present for XGMII interface.
4, There is no PHY for XFI, so removed related phy address settings.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4240 has voltage ID fuse. Read the fuse and configure the voltage
correctly. Core voltage has higher tolerance on over side than below.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Update the timing table to support more rank density, based on the theory
that similar density DIMMs have similar clock adjust and write level start
timing. Update the timing for 1600 and 1866 MT/s. Tested with Micron
MT18JSF1G72AZ-1G9E1 DIMMs, iDIMM M3CN-4GMJ3C0C-M92.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Reverse the bit sequence to set and display serdes clock frequency
correctly. The correct bit maps in BRDCFG2 are
0 1 2 3 4 5 6 7
S1RATE[1:0] S2RATE[1:0] S3RATE[1:0] S4RATE[1:0]
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and file name. Fix
them. Also fix reference to doc/README.SPL file.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
MUX2_CTR is on GPIO1[5], not GPIO2[5], and it needs to be set high in order to
connect the FEC.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
There is no change of behavior, except for older silicon revisions for which
support is removed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The signal connected from this pin to the PMIC is WDOG_B, i.e. ALT0 mode, not
ALT1 (which even corresponds to nothing).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
There is no change of behavior, even if some pad control values could probably
be simplified.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from
Freescale, which results in much better stability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When P1021RDB-PC reboot system, the board will hung at uboot DDR
configuration. For P1021RDB-PC DDR reset pin is multiplex with
QE, so uboot will reserve this pin for QE and skip DDR reset.
Other platforms without QE will do this reset. This patch adds
a slight code to reset DDR chip by QE CE_PB8 pin for NAND and
NOR FLASH boot. For booting from SPI FALSH and SD card, it
seems possible to use the rom on chip to write to the GPIO
pins before configuring the DDR.
Signed-off-by: Xu Jiucheng <B37781@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Change flexcan compatible string from "fsl,flexcan-v1.0"
to "fsl,p1010-flexcan" to match the device tree.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Resolve P1020 second USB controller multiplexing with eLBC
- mandatory to mention USB2 in hwconfig string to select it
over eLBC, otherwise USB2 node is removed
- works only for SPI and SD boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhicheng Fan <B32736@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add the tlb entries based on the configuration of the SRIO interfaces.
Every SRIO interface has 256M space:
#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add defines needed to access NAND, remove second flash bank that is
actually connected to NAND.
Add nand booting support for P1022DS with hardcoded DDR config using
SPL framework from 2011
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For linux 3.x, the size of each item in interrupt-map property is 9 not 7.
Don't use the static value and calculate the size with following cells:
PCI #address-cells, PCI #interrupt-cells,
PIC address, PIC #address-cells, PIC #interrupt-cells.
Signed-off-by: Bin Jiang <bin.jiang@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch add support for storing the environment redundant on
mmc devices. Substantially it re-uses the logic from the NAND implementation,
that means using an incremental counter for marking newer data.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
PUE requires PKE to mean something, as do pull values with PUE, so do not
compell users to explicitly use PKE and PUE everywhere. This is also what is
done on Linux and what has already been done for i.MX51.
By the way, remove some unused pad control definitions.
There is no change of behavior.
Note that SPI_PAD_CTRL was defined by several boards with a pull value, but
without PKE or PUE, which means that no pull was actually enabled in the pad.
This might be a bug in those boards, but this patch does not change the
behavior, so it just removes the meaningless pull value from those definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
IIM:
- Homogenize prg_p naming (the reference manuals are not always self-consistent
for that).
- Add missing SCSx and bank registers.
- Fix the number of banks on i.MX53.
OCOTP:
- Rename iim to ocotp in order to avoid confusion.
- Rename fuse_data to read_fuse_data, and sticky to sw_sticky, according to the
reference manual.
- Merge the existing spinoff gp1 fuse definition on i.MX6.
- Fix the number of banks on i.MX6.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Stefano Babic <sbabic@denx.de>
imx-regs.h is more appropriate location for containing register masks.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Setup CCM_CCOSR register to provide a CKO1 clock frequency of 16.5 MHz.
CKO1 drives sgtl5000 codec clock on mx6qsabrelite and doing this setup in the
bootloader will allow us to remove a lot of code in arch/arm/mach-imx/mach-imx6q.c
from the mainline kernel.
mx6q_4x_mt41j128.cfg is also used by mx6qsabresd, and it is safe to use it for
this board as well.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Titanium is a i.MX6 based board from ProjectionDesign / Barco. This
patch adds support for this board with the newly introduced NAND
support for i.MX6.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Commit 3ebd1cbc introduced compiler-generated __bss_start
and __bss_end__ and commit c23561e7 rewrote all __bss_end__
as __bss_end. Their merge caused silent and harmless but
potentially bug-inducing clashes between compiler- and linker-
generated __bss_end symbols.
Make __bss_end and __bss_start compiler-only, and create
__bss_base and __bss_limit for linker-only use.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Let all ARM linker scripts handle properly -ffunction-sections
and -fdata-sections. This will be useful for future changes in order to create
symbol-specific sections in common .S files.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Commit e05e5de7fa made the 2 1st parameters of
ARM's relocate_code() useless since it moved the code handling them to crt0.S.
So, drop these parameters.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This also fixes support for mx31pdk and tx25, which had been broken by commit
e05e5de7fa.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Add support for the Samsung K9LAG08U0M NAND Flash (2-GiB MLC NAND Flash, 2-kiB
pages, 256-kiB blocks, 30-ns R/W cycles, 1 CS) on mx53ard.
eNFC_CLK_ROOT is set up with a cycle time of 37.5 ns (400 MHz / 3 / 5) for this
board, which satisfies the 30-ns NF R/W cycle requirement.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
board/freescale/mx6qsabrelite/README explain a procedure to
update the SPI-NOR on the SabreLite board without Freescale
manufacturing tool but following this procedure leads to both
"sf erase" and "sf write" failing on a mx6qsabrelite board:
MX6QSABRELITE U-Boot > sf probe 1
MX6QSABRELITE U-Boot > sf erase 0 0x40000
SPI flash erase failed
MX6QSABRELITE U-Boot > sf write 0x10800000 0 0x40000
SPI flash write failed
This is because the chip-select 1 is wrong and the correct
value is 0x7300.
Since commit c1173bd0 ("sf command: allow default bus and chip selects")
the chip-select and bus arguments for the sf probe command are optional
so let's just remove it and use "sf probe" instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
When booting a Freescale kernel 3.0.35 on a Wandboard solo, the get_board_rev()
returns 0x62xxx, which is not a value understood by the VPU
(Video Processing Unit) library in the kernel and causes the video playback to
fail.
The expected values for get_board_rev are:
0x63xxx: For mx6quad/dual
0x61xxx: For mx6dual-lite/solo
So adjust get_board_rev() accordingly and make it as weak function, so that we
do not need to define it in every mx6 board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Maximum bus width supported by some i.MX6 boards is not 8bit like
others. In case where both host controller and card support 8bit transfers,
they agree to communicate on 8bit interface while some boards support only 4bit interface.
Due to this reason the mmc 8bit default mode fails on these boards. To rectify this,
define maximum bus width supported by these boards (4bit). If max_bus_width is not
defined, it is 0 by default and 8bit width support will be enabled in host
capabilities otherwise host capabilities are modified accordingly.
It is tested with a MMCplus card.
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
cc: stefano Babic <sbabic@denx.de>
cc: Andy Fleming <afleming@gmail.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Adds support for 'bmode' command which let user to choose where to
boot from; this allows U-Boot to load system from another storage
without messing with jumpers.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This documents the SD card identifier so it is easier for user to spot
which card number will be used, if need.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
Note this is a tree-wide change affecting multiple architectures.
At present we use __bss_start, but mostly __bss_end__. This seems
inconsistent and in a number of places __bss_end is used instead.
Change to use __bss_end for the BSS end symbol throughout U-Boot. This
makes it possible to use the asm-generic/sections.h file on all
archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Refactor linker-generated array code so that symbols
which were previously linker-generated are now compiler-
generated. This causes relocation records of type
R_ARM_ABS32 to become R_ARM_RELATIVE, which makes
code which uses LGA able to run before relocation as
well as after.
Note: this affects more than ARM targets, as linker-
lists span possibly all target architectures, notably
PowerPC.
Conflicts:
arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
board/ait/cam_enc_4xx/u-boot-spl.lds
board/davinci/da8xxevm/u-boot-spl-da850evm.lds
board/davinci/da8xxevm/u-boot-spl-hawk.lds
board/vpac270/u-boot-spl.lds
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Turn __bss_start and __bss_end__ from linker-generated
to compiler-generated symbols, causing relocations for
these symbols to change type, from R_ARM_ABS32 to
R_ARM_RELATIVE.
This should have no functional impact, as it affects
references to __bss_start and __bss_end__ only before
relocation, and no such references are done.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Only define enabled clocks in the config file and enable
the clocks in common code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Wolfgang Denk <wd@denx.de>
Remove CSx configurations from board code and only define
required CSx macros in the board config file to configure
chip select windows and parameters.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Wolfgang Denk <wd@denx.de>
Provide a structure for accessing HDMI registers, so that we can use proper
read/write accessors.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Rename all i.MX6 pad declarations to MX6_PAD_x, so a board
may support either i.MX6Quad/Dual (MX6Q) or i.MX6Dual-Lite/Solo
(MX6DL) by including the proper header.
Boards mx6qarm2, mx6qsabreauto, mx6qsabrelite, and mx6qsabresd
only support MX6Q, so they include mx6q_pins.h.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
All the users of mx6q_4x_mt41j128.cfg (DDR3-1333H Micron MT41J128M16HA-15E or SK
hynix H5TQ2G63BFR-H9C for i.MX6Q SABRE Lite, and DDR3-1600K Micron
MT41K128M16JT-125:K for i.MX6 SABRE SD) support the optional down binning to
DDR3-1066F (CL = 7, CWL = 6), which is possible at 532 MHz, so use it.
In these conditions:
tRCD(min) = 13.125 ns
tRP(min) = 13.125 ns
tRC(min) = max(tRAS(min, DDR3-1333H), tRAS(min, DDR3-1600K)) + tRP(min)
tRAS(min, DDR3-1333H) = 36 ns
tRAS(min, DDR3-1600K) = 35 ns
MMDC1_MDCFG0.tCL should be set to 7 nCK, encoded as 0x4 in the bit-field
MMDC1_MDCFG0[3:0].
MR0.CL should be set as in MMDC1_MDCFG0.tCL, i.e. to 7 nCK, which is encoded
as 0x6 in MRS.LMR.MR0.{A6:A4, A2} and MMDC1_MDSCR[22:20, 18].
MMDC1_MDCFG1.tCWL should be set to 6 nCK, encoded as 0x4 in the bit-field
MMDC1_MDCFG1[2:0].
MMDC1_MDCFG1.tRCD should be set to 13.125 ns, which is 7 nCK at 532 MHz, encoded
as 0x6 in the bit-field MMDC1_MDCFG1[31:29].
MMDC1_MDCFG1.tRP should be set to 13.125 ns, which is 7 nCK at 532 MHz, encoded
as 0x6 in the bit-field MMDC1_MDCFG1[28:26].
MMDC1_MDCFG1.tRC should be set to 49.125 ns, which is 27 nCK at 532 MHz, encoded
as 0x1A in the bit-field MMDC1_MDCFG1[25:21].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
MR0.PPD should be set as in MMDCx_MDPDC.SLOW_PD, i.e. to fast-exit mode, which
is encoded as 1 in MRS.LMR.MR0.A12 and MMDCx_MDSCR[28].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
MMDC1_MDOR.RST_to_CKE should be set to 500 µs according to the JEDEC
specification for DDR3. With a cycle of 15.258 µs, this gives 33 cycles encoded
as 0x23 for the bit-field MMDC1_MDOR[5:0].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
MMDC1_MDOR.SDE_to_RST should be set to 200 µs according to the JEDEC
specification for DDR3. With a cycle of 15.258 µs, this gives 14 cycles encoded
as 0x10 for the bit-field MMDC1_MDOR[13:8].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
MMDC1_MDOR.tXPR should be set as specified for the JEDEC DDR3 timing tXPR.
For all DDR3 speed bins:
tXPR(min) = max(5 nCK, tRFC(min) + 10 ns)
tRFC(2 Gb) = 160 ns
All the users of mx6q_4x_mt41j128.cfg have a 2-Gb density (Micron
MT41J128M16HA-15E or SK hynix H5TQ2G63BFR-H9C for i.MX6Q SABRE Lite, and Micron
MT41K128M16JT-125:K for i.MX6 SABRE SD).
Hence, MMDC1_MDOR.tXPR should be set to max(5 nCK, 170 ns), which is 170 ns
and 91 nCK at 532 MHz, encoded as 0x5A in the bit-field MMDC1_MDOR[23:16].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
MMDC1_MDCFG1.tMRD should be set to max(tMRD, tMOD) for DDR3.
For all DDR3 speed bins:
tMRD(min) = 4 nCK
tMOD(min) = max(12 nCK, 15 ns)
Hence, MMDC1_MDCFG1.tMRD should be set to max(12 nCK, 15 ns), which is 12 nCK
at 532 MHz, encoded as 0xB in the bit-field MMDC1_MDCFG1[8:5].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Move these fields into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update for bsc9132qds.c, b4860qds.c]
Signed-off-by: Tom Rini <trini@ti.com>
QIXIS FPGA is accessable via both i2c and flash controller.
Only flash controller access is supported.
Add support of i2c based access. It is quite useful in the scenario
where either flash controller path is broken or not present.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9132QDS is a Freescale reference design board for BSC9132 SoC.
BSC9132 SOC is an integrated device that targets the evolving Microcell,
Picocell, and Enterprise-Femto base station market subsegments.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
BSC9132QDS Overview
--------------------
2Gbyte DDR3 (on board DDR), Dual Ranki
32Mbyte 16bit NOR flash
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
SD slot
USB-ULPI
eTSEC1: Connected to SGMII PHY
eTSEC2: Connected to SGMII PHY
PCIe
CPRI
SerDes
I2C RTC
DUART interface: supports one UARTs up to 115200 bps for console display
Apart from the above it also consists various peripherals to support DSP
functionalities.
This patch adds support for mainly Power side functionalities and peripherals
Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
All the dev boards of Freescale's QorIQ family have a RCW that is
supported by the u-boot.pbl build target. This patch adds one for the
P2041 dev board.
This RCW is suitable for the RAMBOOT_PBL scenarios and was tested on the
P2041RDB booting from the eSPI NOR Flash (P2041RDB_SPIFLASH config).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Qixis FPGA has tag data contains image name and build date.
It is helpful to identify the FPGA image precisely.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This function is called by "qixis_reset switch" command and
switch settings are calculated from qixis FPGA registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This function is called by "qixis_reset switch" command
and switch settings are calculated from FPGA/qixis registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Remove #ifdef so that "qixis dump" command is always available
Add "qixis_reset switch" command to dump switch settings
Qixis doesn't have 1:1 switch mapping. We need to reverse engineer from
registers to figure out switch settings. Not all bits are available.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.
B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
configuration reset source. The RCW source is set by appropriate
DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
- On-board eCWTAP controller with ETH and USB I/F
- JTAG/COP 16-pin header for any external TAP controller
- External JTAG source over AMC to support B2B configuration
- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
- total four refclk, including CPRI clock scheme
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
QIXIS FPGA's QIXIS Tag Access register (QTAG) defines TAG, VER, DATE, IMAGE
fields. These fields have FPGA build version, image name and build date
information.
Add support to parse these fields to have complete FPGA image information.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The internal SRAM of Freescale's IFC NAND machine is of 64K and controller's
Address Mask Registers is initialised with the same.
So Update TLB and LAW size of NAND flash accordingly.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Static variables should be defined in C files, not header files, because
otherwise every C file that #includes the header file will generate a
duplicate of the variables. Since the vsc3316_xxx[] arrays are only
used by t4qds.c anyway, just put the variables there.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Lanes mux currently is configured in eth.c when initializing FMAN ethernet
ports, but SRIO and PCIe also need lanes mux, so we move the lanes mux to
p2041rdb.c which implements a board-specific initialization and will be
called at early stage.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The following features are supported:
* 128 MB DDR1 SDRAM
* DUART
* SD/MMC Card Socket
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Some MXS based boards do not implement the card-detect signal. Allow
user to specify alternate card-detect implementation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The '#' used as comments in the files cause the preprocessor
trouble, so change to /* */.
The mkimage command which uses this preprocessor output
was moved to arch/arm/imx-common/Makefile
.gitignore was updated to ignore .cfgtmp files.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Add DVI output support and make it the default video output.
Currently the CLAA WVGA panel is supported, but this panel has to be purchased
separately, so using the DVI output as the default would allow more people to
try the splash screen feature on a mx51evk.
If someone still wants to use the CLAA WVGA, just set the panel variable as:
set panel claa
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add support for the Seiko 4.3'' WVGA panel on mx53loco.
By default, the CLAA WVGA panel is selected.
In order to support the Seiko panel, the enviroment variable 'panel' must be
set to 'seiko'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Make the error handling more robust.
Check if each one of the PMIC writes fail and if they do, just return
immediately.
Also, print the cause for the failures.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
commit c73368150 (pmic: Extend PMIC framework to support multiple instances
of PMIC devices) introduced an extra 'retval' variable, but this is not
necessary since we have already the variable 'ret' in place.
So use 'ret' to store the return values from the pmic related calls and remove
'retval'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The on-board number of available usdhc devices is something board
specific. The patch moves CONFIG_SYS_FSL_USDHC_NUM out of
mx6qsabre_common.h and adds usdhc2 and usdhc4 support for mx6qsabresd
board.
To keep the default mmc device for environment same as before (usdhc3),
it moves CONFIG_SYS_MMC_ENV_DEV out of mx6qsabre_common.h and changes
it to 1 for mx6qsabresd.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit c733681 (pmic: Extend PMIC framework to support multiple instances
of PMIC devices) mx53loco fails to allocate the memory for PMIC:
U-Boot 2013.01-rc2-dirty (Dec 20 2012 - 15:55:01)
Board: MX53 LOCO
I2C: ready
DRAM: 1 GiB
pmic_alloc: No available memory for allocation!
pmic_init: POWER allocation error!
CPU: Freescale i.MX53 family rev2.0 at 800 MHz
Reset cause: POR
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Calling the PMIC related functions at a later stage, ie, from board_late_init()
fixes the issue.
Reported-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
This converts MPC8313ERDB NAND boot to use the new SPL infrastructure.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit c73368150 (pmic: Extend PMIC framework to support multiple instances
of PMIC devices) has incorrectly passed the PMIC name under the FSL PMIC case.
Fix that by passing "FSL_PMIC" as the parameter of pmic_get.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Make the necessary adaptions for the new PMIC framework, so that mx25pdk can
be built again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Conflicts:
drivers/power/power_fsl.c
include/configs/mx35pdk.h
include/configs/mx53loco.h
include/configs/woodburn_common.h
board/woodburn/woodburn.c
These boards still use the old old PMIC framework, so they
do not merge properly after the power framework was merged into
mainline.
Fix all conflicts and update woodburn to use Power Framework.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Single rank UDIMM timing has been verified with HMT325U7BFR8C-H9 for speed
800, 900, 1000, 1200, 1300MT/s.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of
P3041DS/P5020DS ("Hydra") reference board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There were a number of shared files that were using
CONFIG_SYS_MPC85xx_DDR_ADDR, or CONFIG_SYS_MPC86xx_DDR_ADDR, and
several variants (DDR2, DDR3). A recent patchset added
85xx-specific ones to code which was used by 86xx systems.
After reviewing places where these constants were used, and
noting that the type definitions of the pointers assigned to
point to those addresses were the same, the cleanest approach
to fixing this problem was to unify the namespace for the
85xx, 83xx, and 86xx DDR address definitions.
This patch does:
s/CONFIG_SYS_MPC8.xx_DDR/CONFIG_SYS_MPC8xxx_DDR/g
All 85xx, 86xx, and 83xx have been built with this change.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Andy Fleming <afleming@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This allows DDR configuration to be deferred to the final U-Boot image,
which is able to make use of SPD data. The SPL itself cannot use SPD due
to code size constraints. It previously used fixed register values for
DDR configuration, and those values did not work on the p2020rdb-pca
board I tested with. It's possible that different revisions of the board
require different settings. Using SPD eliminates that problem.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
- Sort by address, and fix column alignment
- Don't label things as localbus that aren't. Instead, put chipselect
info at the end of the description for localbus windows. Note that
NAND/NOR have their chipselects swapped when booting from NAND, and CS2
can be either PMC or VSC7385 depending on hwconfig.
- Shrink NAND to the 32K that's actually mapped in the localbus
- Assign an address and size to L2 SRAM. Remove the similarly named
but unintelligible "L2 SDRAM(REV.)".
- Remove the untrue comment about L1 stack being mapped with TLB0.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Introduces CONFIG_SPL_RELOC_TEXT_BASE and CONFIG_SPL_RELOC_STACK.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Add support for the OTG port on the mx35pdk Personality board.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
The inclusion of LCD patch into mx53loco breaks the build when
CONFIG_VIDEO is disabled. Fix this by splitting the video
related stuff to a new file.
Also rename the function lcd_iomux to setup_iomux_lcd to make the
namings aligned with the other iomux functions.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The inclusion of LCD patch into mx51evk breaks the build when
CONFIG_VIDEO is disabled. Fix this by splitting the video related
stuff to a new file.
Also rename the function lcd_iomux to setup_iomux_lcd to make the
namings aligned with the other iomux functions.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The PMIC framework has been extended to support multiple instances of
the variety of devices responsible for power management.
This change allows supporting of e.g. fuel gauge, charger, MUIC (Micro USB
Interface Circuit).
Power related includes have been moved to ./include/power directory.
This is a first of a series of patches - in the future "pmic" will be
replaced with "power".
Two important issues:
1. The PMIC needs to be initialized just after malloc is configured
2. It uses list to hold information about available PMIC devices
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
fdt.c:91:78: warning: Using plain integer as NULL pointer
fdt.c:103:78: warning: Using plain integer as NULL pointer
speed.c:55:11: warning: symbol 'corecnf_tab' was not declared. Should it be static?
speed.c:519:5: warning: symbol 'do_clocks' was not declared. Should it be static?
mpc8313erdb.c:73:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:74:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:75:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:76:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:79:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:80:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:81:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:82:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:85:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:86:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:87:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:88:17: warning: obsolete struct initializer, use C99 syntax
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
fsl_corenet_serdes.c:485:6: warning: symbol '__soc_serdes_init' was not declared. Should it be static?
cpu_init.c:185:6: warning: symbol 'invalidate_cpc' was not declared. Should it be static?
bcsr.c:28:27: warning: non-ANSI function declaration of function 'enable_8568mds_duart'
bcsr.c:39:33: warning: non-ANSI function declaration of function 'enable_8568mds_flash_write'
bcsr.c:46:34: warning: non-ANSI function declaration of function 'disable_8568mds_flash_write'
bcsr.c:53:29: warning: non-ANSI function declaration of function 'enable_8568mds_qe_mdio'
bcsr.c:28:33: warning: non-ANSI function declaration of function 'enable_8569mds_flash_write'
bcsr.c:33:34: warning: non-ANSI function declaration of function 'disable_8569mds_flash_write'
bcsr.c:38:28: warning: non-ANSI function declaration of function 'enable_8569mds_qe_uec'
bcsr.c:63:47: warning: non-ANSI function declaration of function 'disable_8569mds_brd_eeprom_write_protect'
ngpixis.c:245:1: error: directive in argument list
ngpixis.c:247:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The M54418TWR lds file need to update since commit:
8b493a5236
common: Discard the __u_boot_cmd section
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
mx25pdk has a Ethernet port that is connected to its internal FEC controller.
In order to power up the Ethernet PHY (DP83640) it is necessary to communicate
with the MC34704 PMIC via I2C.
Make the FEC ethernet port functional
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx25pdk has a SD/MMC slot connected to esdhc1.
Add support for it and allow the environment variables to be saved into SD/MMC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch modifies start.S for the arm1136 to make it
conform to start.S in armv7 architecture, to make it
usable if the SPL framework is used.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add Freescale MCF54418TWR ColdFire development board support.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
The T4240QDS is a high-performance computing evaluation, development and
test platform supporting the T4240 QorIQ Power Architecture™ processor.
SERDES Connections
32 lanes grouped into four 8-lane banks
Two “front side” banks dedicated to Ethernet
Two “back side” banks dedicated to other protocols
DDR Controllers
Three independant 64-bit DDR3 controllers
Supports rates up to 2133 MHz data-rate
Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
QIXIS System Logic FPGA
Each DDR controller has two DIMM slots. The first slot of each controller
has up to 4 chip selects to support single-, dual- and quad-rank DIMMs.
The second slot has only 2 chip selects to support single- and dual-rank
DIMMs. At any given time, up to total 4 chip selects can be used.
Detail information can be found in doc/README.t4qds
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add code for configuring VSC3316/3308 crosspoint switches
Add README to understand the APIs
- VSC 3316/3308 is a low-power, low-cost asynchronous crosspoint switch
capable of data rates upto 11.5Gbps. VSC3316 has 16 input and 16
output ports whereas VSC3308 has 8 input and 8 output ports.
Programming of these devices are performed by two-wire or four-wire
serial interface.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
According to new QIXIS system definition, update QIXIS registers set
to add present2 register instead of obsolete ctl_sys2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
QIXIS FPGA layout defines the address of registers but The actual register bit
implementation is board-specific,
So avoid use of magic numbers as it may vary across different boards's QIXIS
FPGA implementation.
Also, Avoid board specific defines in common/qixis.h
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Adds support for HDMI, two LVDS panels and one RGB panel to
the SABRE-Lite board.
Displays supported:
HDMI - 1024 x 768 for maximum compatibility
Hannstar-XGA - 1024 x 768 LVDS (Freescale part number MCIMX-LVDS1)
wsvga-lvds - 1024 x 600 LVDS (Boundary p/n Nit6X_1024x600)
wvga-rgb - 800 x 480 RGB (Boundary p/n Nit6X_800x480)
Since the ipuv3_fb display driver currently supports only a single display,
this code auto-detects panel by probing the HDMI Phy for Hot Plug Detect
or the I2C touch controller of the LVDS and RGB displays in the priority
listed above.
Setting 'panel' environment variable to one of the names above will
override auto-detection.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The kernel from Freescale expects that the bootloader passes the board revision.
Read the board revision and pass it via get_board_rev().
Without passing the board revision the kernel does not operate properly as the
initialization of peripherals are different in revA versus revB boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not
suitable for the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
This patch fixes this issue by adding a configuration field for the SDHC input
clock frequency.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Andy Fleming <afleming@gmail.com>
Clean up mx35 lowlevel_init:
- Indent with tabs.
- Fix comments.
- Use defined values instead of literal constants.
- Use defined macros instead of duplicating code.
- Use macro parameters with default values instead of #define'd configs.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0
register is actually composed of two bit-fields: one pre-divider and one
post-divider. This patch fixes the CCM access macros and the code using them
accordingly.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of
duplicated definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6qsabresd has a AR8031 Gigabit PHY.
Add support for it.
Also increase CONFIG_SYS_MALLOC_LEN so that FEC buffer allocation does not fail.
Tested on 1Gbp and 100Mbps networks.
Suggested-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
mx6qsabresd is a board based on mx6q SoC with the following features:
- 1GB of DDR3
- 1 USB OTG port
- 1 HDMI output port
- SPI NOR
- LVDS panel
- Gigabit Ethernet
- Camera Connector
- eMMC and SD card slot
- Audio
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
fecmxc_mii_postcall() is specific to the KSZ9021 PHY on m28evk and
should not be used on mx28evk, which has LAN8270 instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG
information.
If this data is not present, the kernel misconfigures the TZIC, which results in
the timer interrupt handler never being called, so the kernel deadlocks while
calibrating its delay.
Suggested-by: Greg Topmiller <Greg.Topmiller@jdsu.com>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Add support for the onboard eSDHC MMC controller. The hardware on the
MPC8308RDB has the following errata:
- ESDHC111: manual asynchronous CMD12 is broken
- DMA is broken (PIO works)
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
[added include fsl_esdhc header to prevent implicit declarations of
fsl_esdhc_mmc_init() and fdt_fixup_esdhc()]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The SPI pins are routed to header J8 for testing SPI functionality. A
Spansion flash has been wired up and tested on this header.
This patch breaks support for the second TSEC interface, since the GPIO
pin used as a chip select is pinmuxed with some of the TSEC pins.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Recent conversion from mx28_adjust_memory_params to mxs_adjust_memory_params
missed to update mx28evk, which caused the board not to boot.
Apply the conversion so that the board can boot again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Align the SSP clock speed with oscilator to achieve higher transfer
stability.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
The cache snooping feature of Freescale's eSDHC IP is not available on i.MX, so
disable it globally for this architecture. This avoids setting no_snoop for all
i.MX boards, and it prevents setting a reserved bit of a reserved register if
fsl_esdhc_mmc_init() is used on i.MX, like in
arch/arm/cpu/armv7/imx-common/cpu.c/cpu_mmc_init().
Since no_snoop was only used on i.MX, get rid of it BTW.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
The DRAM initialization, after SPL has complete, is exactly the same
for all mxs SoCs so we should name it accordinly.
The following boards has been changed:
* apx4devkit
* m28evk
* mx28evk
* sc_sps_1
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
Each i.MX has its own gpio.h, defining the same structure.
The internal GPIO controller has the same layout
(at least for the register used by u-boot) and can be shared.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Matt Sealey <matt@genesi-usa.com>
This allows a watchdog reset to start the ROM's
usb/serial downloader, or boot from an sdcard.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This gets us rid of duplication of the same file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
On this board, the console is always set to the serial line.
Do not allow to overwrite it when video is enabled.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On this board, the console is always set to the serial line.
Do not allow to overwrite it when video is enabled.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
LAW init is skipped in the SPL payload because it's assumed that the SPL
has taken care of it -- so make sure the SPL loads all the LAWs as is
done on other boards.
This bug was introduced by:
commit 4589728e21
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Fri Nov 11 08:14:53 2011 -0600
powerpc/85xx: Fix builds of P1020/P2020RDB-PC_36BIT_NAND
Size grew a bit so nand-spl didn't fit in 4k, reduce done by removing
LAW entries not needed during SPL phase.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
enum board_slots contained six values, where SLOT1 == 1, SLOT2 == 2, and
so on. This is pointless, so remove it. Also move the lane_to_slot[]
array to the top of the file so that it can be used by other functions.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In order to figure out which SerDes lane a given Fman port is connected
to, we need a function that maps the fm_port namespace to the srds_prtcl
namespace.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Using the raw value of 0x80000000 directly in the code can
lead to "count the zeros" bugs like that fixed in commit
718e9d13b98 ("MPC85xxCDS: Fix missing LCRR_DBYP bits for
66-133MHz LBC")
Change all existing raw values to use the symbolic value of
LCRR_DBYP instead.
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There was an extra 0 in front of the value we were using to mask,
remove it to improve the code.
Also fix the value written to ddr_sdram_cfg to set the bus width
properly to 16 bits
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Provides a tool to build boot Image for PBL(Pre boot loader) which is
used on Freescale CoreNet SoCs, PBL can be used to load some instructions
and/or data for pre-initialization. The default output image is u-boot.pbl,
for more details please refer to doc/README.pblimage.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.
Slave's ucode and ENV can be stored in master's memory space, then slave
can fetch them through PCIE interface. For the corenet platform, ucode is
for Fman.
NOTE: Because the slave can not erase, write master's NOR flash by
PCIE interface, so it can not modify the ENV parameters stored
in master's NOR flash using "saveenv" or other commands.
environment and requirement:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image is in master NOR flash.
3. Put the slave's ucode and ENV into it's own memory space.
4. Normally boot from local NOR flash.
5. Configure PCIE system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to one PCIE interface by RCW.
3. RCW should configure the SerDes, PCIE interfaces correctly.
4. Must set all the cores in holdoff by RCW.
5. Must be powered on before master's boot.
For the slave module, need to finish these processes:
1. Set the boot location to one PCIE interface by RCW.
2. Set a specific TLB entry for the boot process.
3. Set a LAW entry with the TargetID of one PCIE for the boot.
4. Set a specific TLB entry in order to fetch ucode and ENV from
master.
5. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
6. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
In addition, the processes are very similar between boot from SRIO and
boot from PCIE. Some configurations like the address spaces can be set to
the same. So the module of boot from PCIE was added based on the existing
module of boot from SRIO, and the following changes were needed:
1. Updated the README.srio-boot-corenet to add descriptions about
boot from PCIE, and change the name to
README.srio-pcie-boot-corenet.
2. Changed the compile config "xxxx_SRIOBOOT_SLAVE" to
"xxxx_SRIO_PCIE_BOOT", and the image builded with
"xxxx_SRIO_PCIE_BOOT" can support both the boot from SRIO and
from PCIE.
3. Updated other macros and documents if needed to add information
about boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When compile the slave image for boot from SRIO, no longer need to
specify which SRIO port it will boot from. The code will get this
information from RCW and then finishes corresponding configurations.
This has the following advantages:
1. No longer need to rebuild an image when change the SRIO port for
boot from SRIO, just rewrite the new RCW with selected port,
then the code will get the port information by reading new RCW.
2. It will be easier to support other boot location options, for
example, boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
PHYs on SGMII riser card are used in SGMII mode with different external
IRQs from eTSEC. This means in SGMII mode phy-handle and phy-connection-type
under ethernet node should be updated. Otherwise the PHY interrupt can not
be handled therefor PHY link state change can not be auto detected.
For we have seperate SGMII PHY nodes, ethernet PHY reg fixup is not needed
but it's still be kept to guarantee the sgmii mode could work with old
device tree.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Lane muxing on p2041 is controlled by a reg in CPLD, offset of this reg
is 0xc, CPLD supports SATA by default, we should re-configure the lane
muxing according to RCW, which indicates what SerDes protocol it is running.
Default lane muxing map is as below:
Lane G on bank1 routes to SGMII, controlled by bit 1 of the reg;
Lane A on bank2 routes to AURORA, controlled by bit 0 of the reg;
Lane C/D on bank2 routes to SATA0 and SATA1, controlled by bit 2
and bit 3 respectively.
Default value of these bits for lane muxing is '1', we should set or clear
these bits accoring to RCW.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In order for indirect mode on the PIXIS to work properly, both chip selects
need to be set to GPCM mode, otherwise writes to the chip select base
addresses will not actually post to the local bus -- they'll go to the
NAND controller instead. Therefore, we need to set BR0 and BR1 to GPCM
mode before switching to indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add TLB mappings, board target options, and configuration items
need for SPI/SD boot.
Since P1022DS RevB board, the NOR flash have been changed to 16 bit/28bit
address flash, therefore, when SDHC/ESPI booting and access to eLBC,
the PMUXCR[0~1] must be set to 10b, and PMUXCR[9~10] must be set to
00b for them.
Configure the PX_BRDCFG0[0~1] to 10b which is connected to
SPI devices as SPI_CS(0:3)_B.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
* 'next' of git://git.denx.de/u-boot:
MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
doc: cleanup - move board READMEs into respective board directories
net: sh_eth: add support for SH7757's GETHER
net: sh_eth: modify the definitions of regsiter
net: sh_eth: add SH_ETH_TYPE_ condition
net: sh_eth: clean up for the SH7757's code
net: fec_mxc: Fix MDC for xMII
net: fec_mxc: Fix setting of RCR for xMII
net: nfs: make NFS_TIMEOUT configurable
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
Also drop a few files referring to no longer / not yet supported
boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Add I2C support.
Tested by placing a 24LC16 EEPROM into the U50 slot which comes empty from factory.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
* 'master' of git://git.denx.de/u-boot-arm: (212 commits)
ARM: cache: Move the cp15 CR register read before flushing the cache.
ARM: introduce arch_early_init_r()
PXA: Enable CONFIG_PREBOOT on zipitz2
ARM: mx28: Remove CONFIG_ARCH_CPU_INIT
No need to define CONFIG_ARCH_CPU_INIT.
add new board vl_ma2sc
MTD: SPEAr SMI: Add write support for length < 4 bytes
i2c: designware_i2c.c: Add support for the "i2c probe" command
rtc/m41t62: Add support for M41T82 with HT (Halt Update)
SPL: ARM: spear: Add SPL support for SPEAr600 platform
Makefile: Add u-boot.spr build target (SPEAr)
SPL: ARM: spear: Remove some objects from SPL build
SPL: lib/Makefile: Add crc32.c to SPL build
SPL: common/Makefile: Add image.c to SPL build
arm: Don't use printf() in SPL builds
GPIO: Add SPEAr GPIO driver
net: Multiple updates/enhancements to designware.c
cleanup/SPEAr: Define configuration flags more elegantly
cleanup/SPEAr: Remove unnecessary parenthesis
SPEAr: Correct SoC ID offset in misc configuration space
SPEAr: explicitly select clk src for UART
SPEAr: Remove CONFIG_MTD_NAND_VERIFY_WRITE to speed up NAND access
SPEAr: Enable ONFI nand flash detection for spear3xx and 6xx and evb
SPEAr: Enable CONFIG_SYS_FLASH_EMPTY_INFO macro
SPEAr: Correct the definition of CONFIG_SYS_MONITOR_BASE
SPEAr: Enable CONFIG_SYS_FLASH_PROTECTION
SPEAr: Enable dcache for fast file transfer
SPEAr: Enable autoneg for ethernet
SPEAr: Enable udc and usb-console support only for usbtty configuration
SPEAr: Enable usb device high speed support
SPEAr: Initialize SNOR in early_board_init_f
SPEAr: Change the default environment variables
SPEAr: Remove unused flag (CONFIG_SYS_HZ_CLOCK)
SPEAr: Add configuration options for spear3xx and spear6xx boards
SPEAr: Add basic arch related support for SPEAr SoCs
SPEAr: Add interface information in initialization
SPEAr: Add macb driver support for spear310 and spear320
SPEAr: Configure network support for spear SoCs
SPEAr: Place ethaddr write and read within CONFIG_CMD_NET
SPEAr: Eliminate dependency on Xloader table
SPEAr: Fix ARM relocation support
st_smi: Fixed page size for Winbond W25Q128FV flash
st_smi: Change timeout loop implementation
st_smi: Fix bug in flash_print_info()
st_smi: Change the flash probing method
st_smi: Removed no needed dependency on ST_M25Pxx_ID
st_smi: Fix smi read status
st_smi: Move status register read before modifying ctrl register
st_smi: Read status until timeout happens
st_smi: Enhance the error handling
st_smi: Change SMI timeout values
st_smi: Return error in case TFF is not set
st_smi: Add support for SPEAr SMI driver
mtd/NAND: Remove obsolete SPEAr specific NAND drivers
SPEAr: Configure FSMC driver for NAND interface
mtd/NAND: Add FSMC driver support
arm/km: remove calls to kw_gpio_* in board_early_init_f
arm/km: add implementation for read_dip_switch
arm/km: support the 2 PCIe fpga resets
arm/km: skip FPGA config when already configured
arm/km: redefine piggy 4 reg names to avoid conflicts
arm/km: cleanup km_kirkwood boards
arm/km: enable BOCO2 FPGA download support
arm/km: remove portl2.h and use km_kirkwood instead
arm/km: convert mgcoge3un target to km_kirkwood
arm/km: add kmcoge5un board support
arm/km: add kmnusa board support
arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0
cm-t35: fix incorrect NAND_ECC layout selection
ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
ARM: OMAP4/5: Move USB pads to essential list.
ARM: OMAP4/5: Move USB clocks to essential group.
ARM: OMAP4/5: Move gpmc clocks to essential group.
ARM: OMAP4+: Move external phy initialisations to arch specific place.
omap4: Use a smaller M,N couple for IVA DPLL
da850/omap-l138: Enable auto negotiation in RMII mode
omap: am33xx: accomodate input clocks other than 24 Mhz
omap: emif: fix bug in manufacturer code test
omap: emif: deal with rams that return duplicate mr data on all byte lanes
OMAP4+: Force DDR in self-refresh after warm reset
OMAP4+: Handle sdram init after warm reset
ARM: OMAP3+: Detect reset type
arm: bugfix: Move vector table before jumping relocated code
Kirkwood: Add support for Ka-Ro TK71
arm/km: use spi claim bus to switch between SPI and NAND
arm/kirkwood: protect the ENV_SPI #defines
ARM: don't probe PHY address for LaCie boards
lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2
lacie_kw: fix SDRAM banks number for net2big_v2
Kirkwood: add lschlv2 and lsxhl board support
net: add helper to generate random mac address
net: use common rand()/srand() functions
lib: add rand() function
kwboot: boot kirkwood SoCs over a serial link
kw_spi: add weak functions board_spi_claim/release_bus
kw_spi: support spi_claim/release_bus functions
kw_spi: backup and reset the MPP of the chosen CS pin
kirkwood: fix calls to kirkwood_mpp_conf
kirkwood: add save functionality kirkwood_mpp_conf function
km_arm: use filesize for erase in update command
arm/km: enable mii cmd
arm/km: remove CONFIG_RESET_PHY_R
arm/km: change maintainer for mgcoge3un
arm/km: fix wrong comment in SDRAM config for mgcoge3un
arm/km: use ARRAY_SIZE macro
arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATE
arm/km: add piggy mac adress offset for mgcoge3un
arm/km: add board type to boards.cfg
AT91SAM9*: Change kernel address in dataflash to match u-boot's size
ATMEL/PIO: Enable new feature of PIO on Atmel device
ehci-atmel: fix compiler warning
AT91: at91sam9m10g45ek : Enable EHCI instead OHCI
Atmel : usb : add EHCI driver for Atmel SoC
Fix: AT91SAM9263 nor flash usage
Fix: broken boot message at serial line on AT91SAM9263-EK board
i.MX6 USDHC: Use the ESDHC clock
mx28evk: Fix boot by adjusting HW_DRAM_CTL29 register
i.MX28: Add function to adjust memory parameters
mx28evk: Fix PSWITCH key position
mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove unused CONFIG_MII_GASKET
mx6: Avoid writing to read-only bits in imximage.cfg
m28evk: use same notation to alloc the 128kB stack
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
There is no .S file in this directory, so just remove SOBJS.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
There is no .S file in this directory, so just remove SOBJS.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
There is no .S file in this directory, so just remove SOBJS.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
There is no .S file in this directory, so just remove SOBJS.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Original code was assuming that the fuse revision version for all mx53loco boards
based on Dialog PMIC was the same, which is not the case.
Force the revision of all Dialog-based boards to 0.
This fixes a kernel crash when PMIC is accessed in the 2.6.35 kernel
for Dialog rev E boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.
Signed-off-by: York Sun <yorksun@freescale.com>
On p1010rdb some signals are muxed for tdm/can/uart/flash.
If we don't set fsl_p1010mux:tdm_can to "can" or "tdm" explicitly,
defaultly we keep spi chip selection to spi-flash instead of to
tdm/slic and disable uart1 when not using flexcan, as well disable sdhc.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. BSC9131 SOC
is an integrated device that targets Femto base station market. It combines
Power Architecture e500v2 and DSP StarCore SC3850 core technologies with
MAPLE-B2F baseband acceleration processing elements
BSC9131RDB Overview
-----------------
-1Gbyte DDR3 (on board DDR)
-128Mbyte 2K page size NAND Flash
-256 Kbit M24256 I2C EEPROM
-128 Mbit SPI Flash memory
-USB-ULPI
-eTSEC1: Connected to RGMII PHY
-eTSEC2: Connected to RGMII PHY
-DUART interface: supports one UARTs up to 115200 bps for console display
Apart from the above it also consists various peripherals to support DSP
functionalities.
This patch adds support for mainly Power side functionalities and peripherals
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Add support for CLAA07LC0ACW LCD that connects to the mx53loco board.
Configure the board to show the Linux logo on the LCD.
Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account
the framebuffer usage.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
The ipuv3 driver is currently only used on mx51, but it can be extended to work
on mx53 and mx6 as well.
Rename mx51_fb_init(), so that it can be used by other SoCs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Add support for CLAA07LC0ACW LCD that connects to the mx51evk board.
Configure the board to show the Linux logo on the LCD.
Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account
the framebuffer usage.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
There is no need to set the VBUS power enable to 0 first and then to 1.
Set it to 1 in the gpio_direction_output() function.
While at it, use the standard naming convention for the GPIO comment.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information.
The kernel uses this data to distinguish between Dialog versus mc34708 based boards,
and also to distinguish between revA and revB of the mc34708 based boards.
Suggested-by: Yu Li <yk@magniel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
On the mx53loco board with mc34708 PMIC it is necessary to turn on VUSB regulator
so that the mx53 USBH1 PHY receives the 3.3V voltage.
Tested by inserting a USB pen drive in the upper USB slot (USBH1) and then issued the
commands:
usb start
usb info
,which correctly detected and printed the USB pen drive information.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add mc34708 support and set mx53 core frequency at its maximum value of 1GHz.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
As mx53loco board has two variants: one with Dialog PMIC and another with FSL MC34708 PMIC,
we need to be able to build both drivers.
Change pmic_init() and PMIC_NUM_OF_REGS names to avoid build conflicts when both drivers are present.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
NAND support is not enabled by default because Eval Kit is not delivered
with NAND chip. To enable NAND support add CONFIG_CMD_NAND to board config.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Acked-by: Marek Vasut <marex@denx.de>
There are two types of mx53loco boards: initial boards were built with a Dialog
DA9053 PMIC and more recent version is based on a Freescale MC34708 PMIC.
Add DA9053 PMIC support and adjust the required voltages and clocks for running
the CPU at 1GHz.
Tested on both versions of mx53loco boards.
In the case of a MC34708-based board the CPU operating voltage remains at 800MHz.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by : Stefano Babic <sbabic@denx.de>
Print CPU information within board_late_init().
This is in preparation for adding 1GHz support, which requires programming a PMIC
via I2C. As I2C is only available after relocation, print the CPU information
later at board_late_init(), so that the CPU frequency can be printed correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Uses the 'magic_keys' idiom as described in doc/README.kbd:
http://lists.denx.de/pipermail/u-boot/2012-April/122502.html
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
There is a 'gpio_direction_output(87, 0);' call previously, so the GPIO direction is
already established.
Use gpio_set_value() for changing the GPIO output then.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Most 85xx boards can be built as a 32-bit or a 36-bit. Current code sometimes
displays which of these is actually built, but it's inconsistent. This is
especially problematic since the "default" build for a given 85xx board can
be either one, so if you don't see a message, you can't always know which
size is being used. Not only that, but each board includes code that displays
the message, so there is duplication.
The 'bdinfo' command has been updated to display this information, so
we don't need to display it at boot time. The board-specific code is
deleted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When boot from SRIO, slave's ucode can be stored in master's memory space,
then slave can fetch the ucode image through SRIO interface. For the
corenet platform, ucode is for Fman.
Master needs to:
1. Put the slave's ucode image into it's own memory space.
2. Set an inbound SRIO window covered slave's ucode stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.
The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure SRIO switch system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to SRIO1 or SRIO2 by RCW.
3. RCW should configure the SerDes, SRIO interfaces correctly.
4. Slave must be powered on after master's boot.
5. Must define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE because of no ucode
locally.
For the slave module, need to finish these processes:
1. Set the boot location to SRIO1 or SRIO2 by RCW.
2. Set a specific TLB entry for the boot process.
3. Set a LAW entry with the TargetID SRIO1 or SRIO2 for the boot.
4. Slave's u-boot image should be generated specifically by
make xxxx_SRIOBOOT_SLAVE_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
P1010RDB and p1_pc_rdb_pc has incorrect configuration for
CONFIG_DDR_RAW_TIMING. It should be CONFIG_SYS_DDR_RAW_TIMING.
Incorrect setting causes DDR failure in case of SPD absent.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In the p1023rds, when system boots from nor flash, kernel only accesses nor
flash and can not access nand flash with BR0/OR0; when system boots from
nand flash, kernel only accesses nand flash and can not access nor flash
with BR0/OR0.
Default device tree nor and nand node should have the following structure:
Example:
nor_flash: nor@0,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "cfi-flash";
reg = <0x0 0x0 0x02000000>;
bank-width = <2>;
device-width = <1>;
status = "okay";
partition@0 {
label = "ramdisk";
reg = <0x00000000 0x01c00000>;
};
}
nand_flash: nand@1,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,p1023-fcm-nand",
"fsl,elbc-fcm-nand";
reg = <0x2 0x0 0x00040000>;
status = "disabled";
u-boot-nand@0 {
/* This location must not be altered */
/* 1MB for u-boot Bootloader Image */
reg = <0x0 0x00100000>;
read-only;
};
}
When booting from nor flash, the status of nor node is enabled and the
status of nand node is disabled in the default dts file, so do not do
anything.
But, when booting from nand flash, need to do some operations:
o Disable the NOR node by setting status = "disabled";
o Enable the NAND node by setting status = "okay";
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Do the same AXI cache and Qos settings done already in the
SabreLite imximage.cfg for the ARM2 board, too.
It fixes a display flash issue caused by low priority of
the display IDMA channel.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Chen <b02280@freescale.com>
CC: Jason Liu <r64343@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
Acked-by: Jason Liu <r64343@freescale.com>
The board revision is detected accessing to the pmic,
that is not available before relocation (I2C).
This generates the following error:
CPU: Freescale i.MX35 rev 2.0 at 532 MHz.
Reset cause: WDOG
<reg num> = 7 is invalid. Should be less than 0
Board: MX35 PDK 1.0
The revision number is wrong, as a default value is printed
(tested on a mx35pdk Rev. 2.0).
Move the output in the board_late_init(), when
pmic can be accessed.
Signed-off-by: Stefano Babic <sbabic@denx.de>
enable_caches() is implemented now in cpu.c for
ARM1136.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently, board files are setting this field to 0x01
which the manual says is a reserved value. Change to
use the default of 0x02 - 128 cycles.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
The variable "rc" is the return of board_eth_init() function. Initialize
it with an error code, so that this function can return an error when
CONFIG_SMC911X is not set.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This is needed to support Freescale-supplied userspaces.
At the moment, both the IPU and VPU libraries provided by Freescale
in the "imx-lib" package contain routines which scrape the system
revision from /proc/cpuinfo. In the VPU library, this information is
used to load the proper firmware, allowing a single binary to be used
across various i.MX processors.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Define CONFIG_PHY_MICREL, and
minimize the tx clock delay.
There is an issue with 1000 baseTx mode on early revs
of the SabreLite boards. The center tap pin 9 of the mag RJ45
USB combo was connected to the 3.3 filtered supply. Letting
this pin float solved the problem. Symptoms of the problem
were packets with many extra zeroes tacked on the end, and random
bit flips causing a high rate of CRC errors. 10/100 baseTx worked
fine on all revs. To disable 1000 baseTx for these boards, simply
define the environment variable disable_giga. ie.
setenv disable_giga 1
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Boards may have things they want done before or after normal phy config.
Letting the boards call drv->config allows them more flexibilty.
Boards affected by this change are corenet_ds and mpc8544ds.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
MX35PDK board does not need to print CPU revision and reset cause in board file
because this is printed by common code when CONFIG_DISPLAY_CPUINFO is selected
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Use gpio_direction_input prior to gpio_get_value.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Use gpio_direction_input prior to gpio_get_value.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Jason Liu <jason.hui@linaro.org>
This patch adds SPI support for the MX28EVK. Support for
an optionally installed SPI flash is also added. An example
configuration for redundant envrionment from SPI flash is also
added but disabled by default.
This patch has been tested on a MX28EVK Rev. D with an installed
SST25VF032B 32Mbit SPI flash.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch enables USB host support on the MX28EVK board.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Commit 314284b156 has
changed board_mmc_getcd() function prototype, while
mx6qarm2 has still the old one.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
CC: Jason Liu <jason.hui@linaro.org>
CC: Stefano Babic <sbabic@denx.de>
This allows the Linux kernel to use UART1 before pinmux
support is added for UART1
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Jason Liu <jason.hui@linaro.org>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Since commit 97039ab98 (env_mmc: Allow board code to override the environment address)
mmc_get_env_addr is a weak-aliased function in common/env_mmc.c
The mmc_get_env_addr implementation that exists at
board/freescale/common/sdhc_boot.c is meant to be used only for PowerPC boards,
but currently it is being used for all platforms that have CONFIG_ENV_IS_IN_MMC defined.
Introduce CONFIG_FSL_FIXED_MMC_LOCATION so that the boards that need to use
the mmc_get_env_addr version from board/freescale/common/sdhc_boot.c could activate
this config option on their board file.
This fixes the retrieval of CONFIG_ENV_OFFSET on non-PowerPC boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefano Babic <sbabic@denx.de>
Add the initial support for Freescale i.MX6Q Sabre Lite board
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
Remove 'all' target from Makefile, as this is unused code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Add initial support for Freescale MX28EVK board.
Tested boot via SD card and by loading a kernel via TFTP through
the FEC interface.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Bits 0 and 1 of CCM_CCGR7 are the usboh3 clock enable bits. Enabling this
clock is necessary for the USB download.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
CC: Jason Hui <jason.hui@linaro.org>
Acked-by: Jason Hui <jason.hui@linaro.org>
This enable the network function on the i.mx6q armadillo2
board(arm2), thus we can use tftp to load image from network.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
fsl_lbc: add printout of LCRR and LBCR to local bus regs
sbc8548: Fix up local bus init to be frequency aware
sbc8548: enable support for hardware SPD errata workaround
sbc8548: relocate fixed ddr init code to ddr.c file
sbc8548: Make enabling SPD RAM configuration work
sbc8548: Fix LBC SDRAM initialization settings
sbc8548: enable ability to boot from alternate flash
sbc8548: relocate 64MB user flash to sane boundary
Revert "SBC8548: fix address mask to allow 64M flash"
MPC85xxCDS: Fix missing LCRR_DBYP bits for 66-133MHz LBC
eXMeritus HWW-1U-1A: Add support for the AT24C128N I2C EEPROM
eXMeritus HWW-1U-1A: Minor environment variable tweaks
* 'master' of git://git.denx.de/u-boot-mpc83xx:
mpc8313erdb: fix mtdparts address
powerpc/83xx/km: add support for 8321 based tuge1 board
powerpc/83xx/km: merge tuxa and tuda1 boards to tuxx1
powerpc/83xx/km: remove obsolete defines for tuda1
powerpc/83xx/km: update SDRAM parameters for km8321 boards
mpc8313erdb: Enable GPIO support on the MPC8313E RDB
mpc83xx: Add a GPIO driver for the MPC83XX family
gpio: Replace ARM gpio.h with the common API in include/asm-generic
gpio: Modify common gpio.h to more closely match Linux
These boards were meaning to deploy this value:
#define LCRR_DBYP 0x80000000
but were missing a zero, and hence toggling a bit that
lands in an area marked as reserved in the 8548 reference
manual.
According to the documentation, LCRR_DBYP should be used as:
PLL bypass. This bit should be set when using low bus
clock frequencies if the PLL is unable to lock. When in
PLL bypass mode, incoming data is captured in the middle
of the bus clock cycle. It is recommended that PLL bypass
mode be used at frequencies of 83 MHz or less.
So the impact would most likely be undefined behaviour for
LBC peripherals on boards that were running below 83MHz LBC.
Looking at the actual u-boot code, the missing DBYP bit was
meant to be deployed as follows:
Between 66 and 133, the DLL is enabled with an
override workaround.
In the future, we'll convert all boards to use the symbolic
DBYP constant to avoid these "count the zeros" problems, but
for now, just fix the impacted boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The new API no longer uses the extra cd parameter that was used to store
the card presence state. Instead, this information is returned via the
function's return value. board_mmc_getcd() returns -1 to indicate that
no card-detection mechanism is implemented; 0 indicates that no card is
present and 1 is returned if it was detected that a card is present.
The rationale for this change can be found in the following email
thread:
http://lists.denx.de/pipermail/u-boot/2011-November/110180.html
In summary, the old API was not consistent with the rest of the MMC API
which always passes a struct mmc as the first parameter. Furthermore the
cd parameter was used to mean "card absence" in some implementations and
"card presence" in others.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Jason Liu <jason.hui@linaro.org>
Fix:
mx51evk.c:206:6: error: conflicting types for 'board_ehci_hcd_init'
/u-boot/include/usb/ehci-fsl.h:254:5: note: previous declaration of
'board_ehci_hcd_init' was here
We also fix board_ehci_hcd_init() for mx53loco board.
Building for mx53loco worked since <usb/ehci-fsl.h> is
not included here.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Add the initial support for Freescale i.MX6Q Armadillo2 board
Support: MMC boot from slot 0/1, debug UART(UART4), usdhc.
There is two MMC slots on the boards:
mmc dev 0 -> connect USDHC3 -> the lower slot on the board,
mmc dev 1 -> connect USDHC4 -> the upper slot on the board,
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
* 'master' of git://git.denx.de/u-boot-arm:
davinci: Remove unwanted memsize.c from hawkboard's nand spl build
devkit8000: Move CONFIG_SYS_TEXT_BASE out of bss
da850evm: pass board revision info to kernel
arch/arm/include/asm/arch-omap5/clocks.h: Fix GCC 4.2 warnings
arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix GCC 4.6 warnings
arch/arm/cpu/armv7/omap-common/spl.c: Fix GCC 4.2 warnings
MX35: flea3: changes due to hardware revision B
MX: serial_mxc: cleanup removing nasty #ifdef
M28: Fix OB1 bug in GPIO driver
MXS: Add static annotations to dma driver
apbh_dma: return error value on timeout
Efika: Configure additional regulators for HDMI output
mx5: Correct a warning in clock.c
MC13892: Add REGMODE0 bits definitions
mx51evk: Configure the pins as GPIOs prior to using gpio_get_value
mx53smd: Configure the pins as GPIOs prior to using gpio_get_value
mx53evk: Configure the pins as GPIOs prior to using gpio_get_value
mx53ard: Configure the pins as GPIOs prior to using gpio_get_value
mx53loco: Configure the pins as GPIOs prior to using gpio_get_value
OMAP3: Add SPL_BOARD_INIT hook
AM3517 CraneBoard: Add SPL support
AM3517: Add SPL support
OMAP3: Add SPL support to omap3_evm
OMAP3: Add SPL support to Beagleboard
OMAP3 SPL: Add identify_nand_chip function
OMAP3 SPL: Rework memory initalization and devkit8000 support
OMAP3: Suffix all Micron memory timing parts with their speed
OMAP3: Add optimal SDRC autorefresh control values
omap3: mem: Add MCFG helper macro
OMAP3: Remove get_mem_type prototype
OMAP3: Change mem_ok to clear again after reading back
OMAP3: Add a helper function to set timings in SDRC
OMAP3: Update SDRC dram_init to always call make_cs1_contiguous()
omap3: mem: Comment enable_gpmc_cs_config more
ARM: davici_emac: Fix condition for number of phy detects
arm: printf() is not available in some SPL configurations
arm, davinci: add support for am1808 based enbw_cmc board
arm, davinci: move misc function in arch tree
arm, board/davinci/common/misc.c: Codingstyle cleanup
arm, davinci, da850: add uart1 tx rx pinmux config
arm, davinci: move davinci_rtc struct to hardware.h
arm, davinci: Remove duplication of pinmux configuration code
arm, hawkboard: Use the pinmux configurations defined in the arch tree
arm, da850evm: Use the pinmux configurations defined in the arch tree
arm, da850: Add pinmux configurations to the arch tree
arm, da850evm: Do pinmux configuration for EMAC together with other pinmuxes
arm, hawkboard: Remove obsolete struct pinmux_config i2c_pins
arm, davinci: Move pinmux functions from board to arch tree
arm, arm926ejs: always do cpu critical inits
omap_gpmc: use SOFTECC in SPL if it's enabled
nand_spl_simple: add support for software ECC
AM3517: move AM3517 specific mux defines to generic header
AM35xx: add EMAC support
davinci_emac: hardcode 100Mbps for AM35xx and RMII
davinci_emac: fix for running with dcache enabled
arm926ejs: add noop implementation for dcache ops
davinci_emac: conditionally compile specific PHY support
davinci_emac: use internal addresses in buffer descriptors
davinci_emac: move arch-independent defines to separate header
BeagleBoard: config: Really switch to ttyO2
ARM: davinci_dm6467Tevm: Fix build breakage
ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unused
ARM: OMAP3: Remove unused define SDRC_R_C_B
ARM: OMAP3: Remove unused define CONFIG_OMAP3430
omap4: fix IO setting
omap4+: streamline CONFIG_SYS_TEXT_BASE and other SDRAM addresses
omap4460: add ES1.1 identification
omap4: emif: fix error in driver
omap: remove I2C from SPL
omap4460: fix TPS initialization
omap: fix cache line size for omap3/omap4 boards
omap4: ttyO2 instead of ttyS2 in default bootargs
omap: Improve PLL parameter calculation tool
start.S: remove omap3 specific code from start.S
armv7: setup vector
armv7: include armv7/cpu.c in SPL build
armv7: disable L2 cache in cleanup_before_linux()
arm, arm926ejs: Fix clear bss loop for zero length bss
PXA: Move colibri_pxa270 to board/toradex/
PXA: Flip colibri_pxa27x to pxa-common.h
PXA: Introduce common configuration header for PXA
PXA: Rename pxa_dram_init to pxa2xx_dram_init
PXA: Squash extern pxa_dram_init()
PXA: Export cpu_is_ and pxa_dram_init functions
PXA: Cleanup Colibri PXA270
PXA: Replace timer driver
PXA: Add cpuinfo display for PXA2xx
PXA: Separate PXA2xx CPU init
PXA: Rename CONFIG_PXA2[57]X to CONFIG_CPU_PXA2[57]X
PXA: Unify vpac270 environment size
PXA: Enable command line editing for vpac270
PXA: Adapt Voipac PXA270 to OneNAND SPL
PXA: Drop Voipac PXA270 OneNAND IPL
PXA: Fixup PXA25x boards after start.S update
PXA: Re-add the Dcache locking as RAM for pxa250
PXA: Rework start.S to be closer to other ARMs
PXA: Drop XM250 board
PXA: Drop PLEB2 board
PXA: Drop CRADLE board
PXA: Drop CERF250 board
Fix regression in SMDK6400
nand: Add common functions to linux/mtd/nand.h
Ethernut 5 board support
net: Armada100: Fix compilation warnings
ARM: remove duplicated code for LaCie boards
ARM: add support for LaCie 2Big Network v2
mvsata: fix ide_preinit for missing disks
netspace_v2: Read Ethernet MAC address from EEPROM
omap3evm: Add support for EFI partitions
part_efi: Fix compile errors
Description of SerDes clock Bank2 setting in p2041 hardware specification
is wrong, the clock map which based on it is wrong either, so fix the
serdes clock map.
wrong setting of SERDES Reference Clocks Bank2:
SW2[5:6] = ON OFF =>100MHz for PCI mode
SW2[5:6] = OFF ON =>125MHz for SGMII mode
right setting of SERDES Reference Clocks Bank2:
SW2[5:6] = OFF OFF =>100MHz for PCI mode
SW2[5:6] = OFF ON =>125MHz for SGMII mode
SW2[5:6] = ON OFF =>156.25MHZ
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Configure the pins as GPIO prior to using gpio_get_value.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <jason.hui@linaro.org>
Configure the pins as GPIO prior to using gpio_get_value.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <jason.hui@linaro.org>
Fix:
mpc8610hpcd.c: In function 'pci_init_board':
mpc8610hpcd.c:238:15: warning: variable 'pordevsr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This adds support for the Freescale COM Express P2020 board. This board
is similar to the P1_P2_RDB, but has some extra (as well as missing)
peripherals.
Unlike all other mpc85xx boards, it uses a watchdog timeout to reset.
Using the HRESET_REQ register does not work.
This board has no NOR flash, and can only be booted via SD or SPI. This
procedure is documented in Freescale Document Number AN3659 "Booting
from On-Chip ROM (eSDHC or eSPI)." Some alternative documentation is
provided in Freescale Document Number P2020RM "P2020 QorIQ Integrated
Processor Reference Manual" (section 4.5).
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P3060QDS is a Freescale reference board for the six-core P3060 SOC.
P3060QDS Board Overview:
Memory subsystem:
- 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
- 128M Bytes NOR flash single-chip memory
- 16M Bytes SPI flash
- 8K Bytes AT24C64 I2C EEPROM for RCW
Ethernet:
- Eight Ethernet controllers (4x1G + 4x1G/2.5G)
- Three VSC8641 PHYs on board (2xRGMII + 1xMII)
- Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C: Four I2C controllers
UART: Supports two dUARTs up to 115200 bps for console
RapidIO: Two RapidIO, sRIO1 and sRIO2
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Configuring for MPC8360EMDS_66_HOST_33 - Board: MPC8360EMDS, Options: CLKIN_66MHZ,PCI,PCI_33M,PQ_MDS_PIB=1
mpc8360emds.c: In function 'board_eth_init':
mpc8360emds.c:178:12: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Size grew a bit so nand-spl didn't fit in 4k, reduce done by removing
LAW entries not needed during SPL phase.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8569mds.c: In function 'local_bus_init':
mpc8569mds.c:306:7: warning: variable 'lbc_hz' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
mpc8568mds.c: In function 'local_bus_init':
mpc8568mds.c:150:7: warning: variable 'lbc_hz' set but not used [-Wunused-but-set-variable]
mpc8568mds.c: In function 'pib_init':
mpc8568mds.c:271:11: warning: variable 'orig_i2c_bus' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
mpc8548cds.c: In function 'local_bus_init':
mpc8548cds.c:87:7: warning: variable 'lbc_hz' set but not used [-Wunused-but-set-variable]
mpc8548cds.c: In function 'lbc_sdram_init':
mpc8548cds.c:121:7: warning: variable 'cpu_board_rev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
pixis.c: In function 'strfractoint':
pixis.c:383:6: warning: variable 'intarr_len' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
cds_pci_ft.c: In function 'cds_pci_fixup':
cds_pci_ft.c:31:12: warning: variable 'tmp' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For ICS307-02, there is one general expression to generate SYSCLK:
CLK1Frequency = InputFrequency * 2 * (VDW + 8) / ((RDW + 2) * OD)
If we want the required frequency for SYSCLK, we must find one solution
to generate this frequency, this solution includes VDW, RDW and OD.
For OD, there are only eight option value: 10, 2, 8, 4, 5, 7, 3, 6.
For RDW, the range is 1 to 127.
For VDW, the range is 4 to 511.
First, we use one OD, RDW and required SYSCLK to calculate the VDW,
if VDW is in it's range, we will calculate the CLK1Frequency with
the OD, RDW and VDW calculated, and we will check this percent
(CLK1Frequency / required SYSCLK), and the precision is 1/1000.
if the percent is less than 1/1000, we think the CLK1Frequency is we want.
Otherwise, We will continue to calculate it with the next OD and RDW.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Include call to usb device-fixup only when CONFIG_HAS_FSL_DR_USB is
defined for the platform - P1020RDB, P1010RDB, P1020-PC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add board_eth_init(). PCIe network card is also supported.
Put RGMII init after tsec_eth_init().
Skip initializing eTSEC3 and eTSEC4 with Carrier boards prior to ver 1.3.
Signed-off-by: Ebony Zhu
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
TBI PHY address (TBIPA) register has been set in general frame manager
phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c
So remove the duplicate code on QorIQ frame manager Ethernet related
platforms, which include Hydra board, P4080DS board and P2041rdb board.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-arm:
Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
arm: jadecpu: Readd MACH_TYPE_JADECPU
at91: defined mach-types for otc570 board in board config file
at91: defined mach-types for meesc board in board config file
mx31pdk: Enable D and I caches
ehci-mxc: remove incorrect comment
README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
mx53: Turn off child clocks before reconfigure perclk_root
qong: enable support for compressed images
imx: imx31_phycore.h: fix checkpatch warnings
vision2: Remove unused get_board_rev function
mx53smd: Remove unused get_board_rev function
mx53ard: Remove unused get_board_rev function
mx53evk: Remove unused get_board_rev function
mx53evk: Add RTC support
mx53loco: Remove unused get_board_rev function
mx53evk: Remove unneeded '1' from mx53evk.h
OMAP3: mvblx: Initial support for mvBlueLYNX-X
ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
omap3: mem: Move comments next to definitions
omap3: mem: Clean-up whitespaces
omap3: mem: Define and use common macros
Davinci: ea20: added PREBOOT to configuration
Davinci: ea20: added I2C support
Davinci: ea20: added video support
VIDEO: davinci: add framebuffer to da8xx
ARM: Davinci: added missing registers to hardware.h
Davinci: ea20: add gpios for LCD backlight control
Davinci: ea20: add gpio for keeping power on in board_late_init
Davinci: ea20: Add default U-Boot environment
Davinci: ea20: Add early init to get early output from console
Davinci: ea20: Add NAND support
Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
Davinci: ea20: set console on UART0
arm, davinci: add cam_enc_4xx support
arm926ejs, davinci: add missing spi defines for dm365
arm926ejs, davinci: add cpuinfo for dm365
arm, davinci: add lowlevel function for dm365 soc
arm, davinci: add header files for dm365
spl, nand: add 4bit HW ecc oob first nand_read_page function
arm, davinci: add support for new spl framework
spl: add option for adding post memory test to the SPL framework
net, davinci_emac: make clock divider in MDIO control register configurable
arm, usb, davinci: make USBPHY_CTL register configurable
usb, davinci: add enable_vbus() weak function
omap3evm: fix errors caused by multiple definitions
omap3evm: Add (quick) configuration for NAND only
omap3evm: Add (quick) configuration for MMC/SD only
omap3evm: move common config options to new file
omap3evm: Prepare to split configuration
omap3evm: Reorder related config options
omap/spl: actually enable the console
davinci_emac: compilation fix, phy is array now
omap3evm: Set environment variable 'ethaddr'
arm, arm926: fix missing symbols in NAND_SPL mode
arm, davinci: Add function lpsc_syncreset()
arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
arm/km: portl2 environment address update to P1B
arm/km: adapt bootcounter evaluation
arm/km: enable jffs2 cmds
arm/km: trigger reconfiguration for the Xilinx FPGA
arm/km: add boardid and hwkey to kernel command line
ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
netspace_v2: enable I2C EEPROM support
netspace_v2: fix SDRAM configuration
armada100: define CONFIG_SYS_CACHELINE_SIZE
pantheon: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: drop empty asm-offsets.s file
arm/km/mgcoge3un: enhance "waitforne" feature
arm/km: add variable waitforne to mgcoge3un
gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
ARM: dreamplug: fix compilation
ARM: DockStar: fix compilation
ARM: netspace_v2: fix warnings
am335x: Drop board_sysinfo struct
am335x: Temporarily add MACH_TYPE define
misc:pmic:samsung Enable PMIC driver at C210 Universal target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
smdkv310: use macro for mmc data read function address
smdkv310: use spl framework for mmc spl
SMDKV310: use get_ram_size() to validate dram size
SMDKV310: Initialize board id using CONFIG_MACH_TYPE
ORIGEN : use absolute paths and fix tool naming
ORIGEN : enable device tree support
MX25: tx25: Fix building due to missing MACH_TYPE
mx31: Add board support for HALE TT-01
mx31: add ESD control registers
mx31: define pins and init for UART2 and CSPI3
MX35: add support for flea3 board
MX51: vision2: add MACH_TYPE in config file
vision2: Remove unused header file
mx51evk: Remove unused get_board_rev function
mx51evk: Remove unneeded '1' from mx51evk.h
I2C: Fix mxc_i2c.c problem on imx31_phycore
mx35pdk: Add RTC support
mx51evk: Use GPIO API for configuring the IOMUX
mx51evk: Add RTC support
rtc: Make mc13783-rtc driver generic
qong: remove unneeded IOMUX settings
qong: Use mx31_set_gpr to setup USBH2 pins
mx31: Introduce mx31_set_gpr function
mx31pdk: Add MC13783 PMIC support
qong: remove unneeded "1" from qong.h
misc: pmic: fix regression in pmic_fsl.c (SPI)
mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
MX35: Drop unnecessary prototypes from imx-regs.h
I2C: added I2C-2 and I2C-3 to MX35
MX35: factorize common assembly code
MX35: add reset cause as provided by other i.MX
MX35: add pins definition for UART3
MX35: added ESDC structure to imx-regs
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire: The EB+MCF-EV123 boards config update
ColdFire: Fix the compile issue for M52277
ColdFire:Moving the remaining coldfire boards to boards.cfg
Fix:
mpc8266ads.c: In function 'initdram':
mpc8266ads.c:278:9: warning: variable 'spd_size' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
After commit 327474f854, the
M52277EVB_stmicro configuration fail to build. Fix it by moving
the env outside the flash and update the lds file.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
No board information is passed for MX53EVK, so remove get_board_rev function.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
No board information is passed for MX53LOCO, so remove get_board_rev function.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
The new MPC8360EMDS board supports 512MB DDR since 2008.
For 512MB DDR:
BAT0 is used for the first 256MB memory, BAT4 is used for the second
256MB memory and the address space of SDRAM follows the DDR, so if the
size of DDR is 256MB, the BAT4 will be used for SDRAM and if the size of
DDR is 512MB, the BAT4 will be used for the second 256MB memory and
there is no BAT for SDRAM.
Therefore, if the size of DDR is 512MB, this patch will use BAT6 for
SDRAM and BAT5 will be used for PCI MEM to replace the BAT6 after the
codes relocates to the DDR.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Kim Phillips <kim.phillips@freescale.com>
Rename CONFIG_SYS_DDR_CONFIG to include which CS it is configuring
Cleanup the setting of the csnbds to respect the setting of
CONFIG_SYS_DDR_SDRAM_BASE
Use __ilog2 instead of writing the code to compute it
Disable unused CS configs
Ensure ddrlaw.bar is configured
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
GPIO API provides mxc_request_iomux function for setting the IOMUX mode.
Use this function instead of directly writing to the IOMUX register.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add MC13783 PMIC support.
Tested by using the 'date' command, which reads the MC13783 RTC registers:
MX31PDK U-Boot > date
Date: 1970-01-01 (Thursday) Time: 2:22:35
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* 'master' of git://git.denx.de/u-boot-arm:
ARM: Add Calxeda Highbank platform
dkb: make mmc command as default enabled
Marvell: dkb: add mmc support
ARM: pantheon: add mmc definition
davinci: remove config.mk file from the sources
ARM:AM33XX: Add support for TI AM335X EVM
ARM:AM33XX: Added timer support
ARM:AM33XX: Add emif/ddr support
ARM:AM33XX: Add clock definitions
ARM:AM33XX: Added support for AM33xx
omap3/emif4: fix registers definition
davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
davinci: emac: add support for more than 1 PHYs
davinci: emac: add new features to autonegotiate for EMAC
da850evm: Move LPSC configuration to board_early_init_f()
omap4_panda: Build in cmd_gpio support on panda
omap: Don't use gpio_free to change direction to input
mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
OMAP3: overo : Add environment variable optargs to bootargs
OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
OMAP3: overo : Use ttyO2 instead of ttyS2.
da830: add support for NAND boot mode
dm36x: revert cache disable patch
dm644X: revert cache disable patch
devkit8000: Add malloc space
omap: spl: fix build break due to changes in FAT
OMAP3 SPL: Provide weak omap_rev_string
omap: beagle: Use ubifs instead of jffs2 for nand boot
omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
omap: overo: Configure mux for gpio10
SPL: Add DMA library
omap3: Add interface for omap3 DMA
omap3: Add DMA register accessors
omap3: Add Base register for DMA
arm, davinci: add missing LSPC define for MMC/SD1
U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
DaVinci: correct MDSTAT.STATE mask
omap4: splitting padconfs into common, 4430 and 4460
omap4: adding revision detection for 4460 ES1.1
omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
gplug: fixed build error as a result of code cleanup patch
kirkwood_spi: add dummy spi_init()
gpio: mvmfp: reduce include platform file
ARM: orion5x: reduce dependence of including platform file
serial: reduce include platform file for marvell chip
ARM: kirkwood: reduce dependence of including platform file
ARM: armada100: reduce dependence of including platform file
ARM: pantheon: reduce dependence of including platform file
Armada100: Add env storage support for Marvell gplugD
Armada100: Add SPI flash support for Marvell gplugD
Armada100: Add SPI support for Marvell gplugD
SPI: Add SPI driver support for Marvell Armada100
dreamplug: initial board support.
imx: fix coding style
misc: pmic: drop old Freescale's pmic driver
MX31: mx31pdk: use new pmic driver
MX31: mx31ads: use new pmic driver
MX31: mx31_litekit: use new pmic driver
MX5: mx53evk: use new pmic driver
MX5: mx51evk: use new pmic driver
MX35: mx35pdk: use new pmic driver
misc: pmic: addI2C support to pmic_fsl driver
misc: pmic: use I2C_SET_BUS in pmic I2C
MX5: efikamx/efikasb: use new pmic driver
MX3: qong: use new pmic driver
RTC: Switch mc13783 to generic pmic code
MX5: vision2: use new pmic driver
misc: pmic: Freescale PMIC switches to generic PMIC driver
misc:pmic:samsung Enable PMIC driver at GONI target
misc:pmic:max8998 MAX8998 support at a new PMIC driver.
misc:pmic:core New generic PMIC driver
mx31pdk: Remove unneeded config
mx31: provide readable WEIM CS accessor
MX51: vision2: Set global macros
I2C: Add i2c_get/set_speed() to mxc_i2c.c
ARM: Update mach-types
devkit8000: Add config to enable SPL MMC boot
devkit8000: protect board_mmc_init
arm, post: add missing post_time_ms for arm
cosmetic, post: Codingstyle cleanup
arm, logbuffer: make it compileclean
tegra2: Enable MMC for Seaboard
tegra2: Add more pinmux functions
tegra2: Rename PIN_ to PINGRP_
tegra2: Add more clock functions
tegra2: Clean up board code a little
tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
mpc8610hpcd.c: In function 'misc_init_r':
mpc8610hpcd.c:79: warning: format '%02lx' expects type 'long unsigned int', but
argument 2 has type 'int'
mpc8610hpcd.c:86: warning: format '%02lx' expects type 'long unsigned int', but
argument 2 has type 'int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
diu.c: In function 'diu_set_pixel_clock':
diu.c:77: warning: format '%lu' expects type 'long unsigned int', but argument 2
has type 'u32'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
mpc5121ads.c: In function 'misc_init_r':
mpc5121ads.c:256: warning: format '%02lx' expects type 'long unsigned int', but
argument 2 has type 'int'
mpc5121ads.c:263: warning: format '%02lx' expects type 'long unsigned int', but
argument 2 has type 'int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
This renames BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT.
Along the way it removes some leftover
#define BOARD_LATE_INIT 1
and adds some basic documentation for board specific
callbacks in README.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
Fix checkpatch warning and errors in several i.MX related files.
While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c
regarding the usage of extern in a C file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Switch to new pmic generic driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
setup_weimcs() and some macros are added to support the setup
for i.MX31 WEIM chip selects. As a compromise between verbosity
and readability an ASCII-art'ish bit comment is used instead of
bitfields.
All i.MX31 boards have been patched to use this approach using a
helper program to verify the changes.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
Seems people fixed their files to use libfoo.o, but didn't actually
update the creation targets to use $(cmd_link_o_target). Update the
rest of the Makefile's found with grep.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
mpc85xx: Add inline GPIO acessor functions
powerpc/85xx: wait for alignment before resetting SERDES RX lanes (SERDES9)
powerpc/85xx: Fix P2020DS booting
powerpc/85xx: Update USB device tree status based on pin settings
fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpers
powerpc/85xx: Add support for RMan LIODN initialization
powerpc/85xx: Update device tree handling for SRIO
powerpc/85xx: Update setting of SRIO LIODNs
fm: Don't allow disabling of FM1-DTSEC1
fm-eth: Don't mark the MAC we use for MDIO as disabled in device tree
The work-around for P4080 erratum SERDES9 says that the SERDES receiver
lanes should be reset after the XAUI starts tranmitting alignment signals.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A temp variable was used but not declared, with CONFIG_SYS_DRAMSZ1
defined. This variable is now declared in the functione when needed.
Signed-off-by: Stany MARCEL <stany.marcel@novasys-ingenierie.com>
The spa, stm, int, 32 and 16 linking files are identical so there is
no need to differentiate them. A single lds file is now used, and
_config rule are simplified.
Signed-off-by: Stany MARCEL <stany.marcel@novasys-ingenierie.com>
Lds files cleened to remove multiple defined section and modified to
be compliant with --gc-sections added for ColdFire platform in a
previous patch.
Signed-off-by: Stany MARCEL <stany.marcel@novasys-ingenierie.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The following commit removed the code that set odt_rd_cfg and
odt_wr_cfg. With out this code P2020DS board will not boot:
commit 712cf7ab0b
Author: York Sun <yorksun@freescale.com>
Date: Mon Oct 3 09:19:53 2011 -0700
powerpc/mpc8xxx: Merge entries in DDR speed table
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add common function fdt_set_node_status() to assist in various locations
that we set a nodes status. This function utilizes the status values
that are part of the EPAPR spec (on power.org).
fdt_set_status_by_alias() is based on fdt_set_node_status() but uses an
alias string to identify the node to update.
We also add some shortcut functions to help the common cases of setting
"okay" and "disabled":
fdt_status_okay()
fdt_status_disabled()
fdt_status_okay_by_alias()
fdt_status_disabled_by_alias()
Finally, we fixup the corenet_ds ethernet code which previously had
a function by the same name that can be replaced with the new helpers.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
- Rework tlb and law tables.
- PCI2 is not available on MPC8548CDS, so remove it.
- Move the memory map to the board config file.
- Rewrite the board info according to the manual.
- Remove unnecessary macros and redefine some macros to align with other boards.
- Fix some typos.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8536 Rev 1.0 silicon have NMG_eSDHC118 erratum, so that the SDHC write
protected pin polarity does not follow the SD card standard in MPC8536
Rev 1.0 silicon.
The MPC8536DS board invert the SDHC_WP pin as a workaround. However, this
silicon erratum has been fixed in Rev 1.1, So need invert the SDHC_WP
polarity again when use the MPC8536 Rev1.1 and greater on MPC8536DS board.
Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. The SD_DATA[4:7] signals are shared with the SPI chip selects on 8536DS,
so don't set MPC85xx_PMUXCR_SD_DATA that config eSDHC data bus-width
to 4-bit and enable SPI signals.
2. Add eSPI controller and SPI-FLASH definition.
Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is not necessary to keep multiple entries for the same setting in DDR
speed tables. Merge them for smaller tables. Also restructure the tables
for smaller size. Cleanup some typedefs.
Enforce strict checking for speed table. If DIMM is running at higher than
known speed, try to use the highest speed setting. If rank is unknown, it
has to panic.
Removed ODT overriding for P2020DS as it is not necessary.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
The CDS uses PCICLK as SYSCLK. The PCICLK should be 33333333Hz or 66666666Hz.
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CPLD 2.2 removed board watch dog support due to the limitation of CPLD
capacity after adding all the requested features, such as switch overriding.
There is no pin-compatible upgrade part available for current PCB design.
So remove codes related to it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to CPLD 2.2, the default configuration is changed, so updated the
description of CPLD command, otherwise it will confusing.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This table covers DDR frequencies from 666 to 1666. Frequencies 666, 833,
1000, 1066 and 1333 were verified on this board with SO-DIMM
(UG51U6400N8SU-ACF).
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2041RDB supports 3 sysclk frequencies, it's selected by SW1[6~8],
software need to read the SW1 status to decide what the sysclk needs.
SW1[8~6] : frequency
0 0 1 : 83.3MHz
0 1 0 : 100MHz
others: 66.667MHz
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CPLD 2.0 provides a new register which bit[0] is set to '1' will reset
board with initializing the CPLD registers to default values. And add
bit[6] of register at offset 0x5 to use to enable flash bank selection.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Let common code set the machine ID.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Update MPC8349EMDS to use unified DDR driver instead of spd_sdram.c.
The unified driver can initialize data using DDR controller. No need to
use DMA if just to initialze for ECC.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2041RDB has almost identical setup for TLB, LAWS, and PCI with
other P-Series CoreNet platforms.
The only difference between P2041RDB & P3041DS/P4080DS/P5020DS is the
CPLD vs PIXIS FPGA which we can handle via some simple #ifdefs in the
TLB and LAW setup tables.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We currently support 4 SoC/Boards from the P-Series of QorIQ SoCs that
are based on the 'CoreNet' Architecture: P2041RDB, P3041DS, P4080DS, and
P5020DS. There is a significant amount of commonality shared between
these boards that we can refactor into common code:
* Initial LAW setup
* Initial TLB setup
* PCI setup
We start by moving the shared code between P3041DS, P4080DS, and P5020DS
into a common directory to be shared with other P-Series CoreNet boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We shouldn't be setting execute permissions on TLB entries that will not
actually have any code run from them.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
RDIMM has different timing parameters from UDIMM. Create new tables for
RDIMMs. Single-, dual- and quad-rank RDIMMs have been verified with speeds
from 800 to 1333MT/s. Speed table expands to include 1600MT/s for future
use. Single- and quad-rank RDIMM entries are copied into UDIMM tables for
future use.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DDR RCW varies at different speeds. It is common for all platform. Move it
out from corenet_ds.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for RGMII, SGMII and XAUI Ethernet on P2041RDB board.
The five dTSEC can be routed to two on-board RGMII phy, three on-board
SGMII phy or four SGMII phy on SGMII riser card according to different
serdes protocol configuration and board lane configuration. Also updated
the device tree to direct the Fmac MAC to the correct PHY.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 has two 1G ethernet controllers the first can run in
SGMII, RGMII, or RMII. The second can only do SGMII & RGMII.
We need to setup a for SoC & board registers based on our various
configuration for ethernet to function properly on the board.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P3041DS &
P5020DS ("Hydra").
The lane_to_slot[] array is initialized dynamically, since board switches
can be used to control the muxing of SERDES lanes to slots.
The BRDCFG1 PIXIS register is used to route the MII bus to the appropriate
slot. The SERDES configuration is queried to help determine the routing
between MACs and slot/phy combination.
If a XAUI card is inserted, muxing for that card is enabled and never
turned off. The PHY address for the 10G XAUI card depends on the slot in
which it's inserted. If it's in slot 1, the address is 4. If it's in
slot 2, the address is 0.
Update the MDIO routing in the P3041DS and P5020DS device trees based on
the board-level muxing. The SERDES configuration determines which
SGMII/XGMII boards are located in which slots, and so the MDIO bus needs
to be muxed correctly whenever talking to a PHY connected to any Fman MAC.
The Fman Ethernet nodes in the device tree also need to be routed to the
correct PHYs.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P4080DS.
The board supports add-on cards for SGMII and XAUI functionality. Which
slots on the board these cards are in is a function of the SERDES option
selected and muxes on the board.
Additionally because of the high-configurablity which MDIO bus one is
connected to is "selected" via an FPGA register. We create dummy MDIO
bus for the phy layer and hide the mux manipulation in this dummy layer.
Add fman fdt helper function in board common code it'll be used by several
freescale boards that do various muxing of the MDIO signals based on which
controller/interface one is trying to talk to.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove unnecessary or dead code/includes.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We shouldn't be setting execute permissions on TLB entries that will not
actually have any code run from them.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Boot methods supported: NOR Flash, SPI Flash and SDCARD
This patch adds the following basic interfaces:
DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash.
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
Local Bus (IFC):
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
64KB CPLD device(GPCM interface)
SPI Flash:
128 Mbit SPI Flash memory
SD/MMC:
connector to interface with the SD memory card
SATA:
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0:
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC:
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221
eCAN:
Two DB-9 female connectors for Field bus interface
UART:
supports two UARTs up to 115200 bps for console
TDM:
2 FXS ports connected via an external SLIC to the TDM interface.
SLIC:
SPI SLIC
I2C:
Serial EEprom
Real time clock
256 Kbit M24256 I2C EEPROM
PCIe:
PCIe and mPCIe connectors.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following boards share a common design but with minor variations
between them:
P1020MSBG-PC
P1020RDB-PC
P1020UTM-PC
P1021RDB-PC
P1024RDB
P1025RDB
P2020RDB-PC
The P1020RDB-PC shares its roots in the existing P1020RDB board design,
however uses DDR3 instead of DDR2.
P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK.
Key features on these boards include:
* DDR3
* NOR flash
* NAND flash (on RDB's only)
* SPI flash (on RDB's only)
* SDHC/MMC card slot
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
* PCIE slot and mini-PCIE slots
As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported
with this approach. ODT option is forced to fit this set of boards, again
because they don't have regular DIMMs.
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet
specification for writing timing.
VSC firmware Address is defined by default in config file for eTSEC1.
SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.
Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC
have pins multiplexing. QE function needs to be disabled to access Nor Flash
and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below
'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <b26998@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
The function fsl_setup_hose clears the variable pci1_hose.
Set pci1_hose.config_table after it.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The function fsl_setup_hose clears the variable pci1_hose.
Set pci1_hose.config_table after it.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The function fsl_setup_hose clears the variable pci1_hose.
Set pci1_hose.config_table after it.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit 0edf8b5b2f breaks
building on a different directory with the O= parameter.
The patch wil fix this issue, generating always asm-offsets.h before
the other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire:Clean up the CONFIG_STANDALONE_LOAD_ADDR usage
ColdFire:Add mb for 5253 dram initialization
ColdFire:Define the DM9000 byteswap for M5253 board.
ColdFire:Update the env settings for several boards.
ColdFire:disable the NFS define for 52277 board.
ColdFire:Update the timer_init since it was unified.
ColdFire: Cleanup for partial linking and --gc-sections
ColdFire: Update compile flags for each CPUs
ColdFire:Fix the configuration broken for some boards.
The dram initialization sequence should be in order.
This patch add mb for the dram intialization code to make
sure the compiler do not disorder the code.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Introduce the --gc-sections for ColdFire platform and clean up the
corresponding lds file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Updated mx53 ddr3 script in order to align with the latest Freescale version from July 8, 2011:
-change ESDREF[REF_SEL]=01 (for 32KHz), from incorrect setting of 00 (64KHz)
-change DDR3 MR0 write to "setmem /32 0x63fd901c = 0x052080b0" from
"0x092080b0". This changes write recovery from 8 clocks to 6 clocks
(in line with ESDCFG1[tWR])
Signed-off-by: Lily Zhang <r58066@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board.
This device only supports 800x600 resolution, so if that resolution is selected,
assume that this is the device. The device is attached to the LVDS port
on the P1022DS board.
The existing 800x600 entry (for the PDM360NG board) is actually 800x480,
so we fix that. To support two different 800x resolutions, the Y-resolution
is now passed to fsl_diu_init() and both values are used to pick the proper
fb_videomode structure.
The data for the 800x600 video mode is originally from Jiang Yutang.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to
'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break
out if it cannot find 'usb1', so drop the 'else' clause to make driver scan
all the 'usbx'.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current code would print RAM size information like this:
DRAM: DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Turn a number of printf()s into debug() to get rid of the redundant
"DDR: " string like this:
DRAM: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Configuring DCSRCR to define the DCSR space to be 1G instead
of the default 4M. DCSRCR only allows selection of either 4M
or 1G.
Most DCSR registers are within 4M but the Nexus trace buffer
is located at offset 16M within the DCSR.
Configuring the LAW to be 32M to allow access to the Nexus
trace buffer. No TLB modification is required since accessing
the Nexus trace buffer from within u-boot is not required.
Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
* 'master' of git://git.denx.de/u-boot-arm:
ARM: MX5: Fix broken leftover TO-2 errata workaround
MX31: Cleanup clock function
scb9328: Add ARM relocation support
am3517evm: change console device from ttyS2 to ttyO2
Remove volatile qualifier in get_ram_size() calls
TI: TNETV107X Fix Build Error
ARM: add missing CONFIG_SKIP_LOWLEVEL_INIT for armv7
arm: add CONFIG_MACH_TYPE setting and documentation
arm: add __ilog2 function
Timer: Fix misuse of ARM *timer_masked() functions outside arch/arm
EfikaMX: Enable EXT2 booting
EfikaMX: Add missing CONFIG_SYS_TEXT_BASE
EfikaMX: Use correct imximage.cfg
MX27: Update to autogenerated asm-offsets.h
MX5: Update to autogenerated asm-offsets.h
imx: Add support for zmx25 board
imx: Make imx25 compatible to mxc_gpio driver and fix in tx25
imx: Add auto generation of asm-offsets.h for imx25
imx: Add support for USB EHCI on imx25
imx: Use correct imx25 reset.c
imx: Add get_tbclk() function for imx25
ARM: Update maintainer of board scb9328
mx27: Make the UART port number explicit
build: Add targets for auto gen of asm-offsets.h and use it in imx35
mx31pdk: cosmetic: Fix line over 80 characters
P2041RDB Specification:
-----------------------
Memory subsystem:
* 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 256 Kbit M24256 I2C EEPROM
* 16 Mbyte SPI memory
* SD connector to interface with the SD memory card
Ethernet:
* dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
* dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
PCIe:
* Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
* Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
I2C:
* I2C1: Real time clock, Temperature sensor, Memory module
* I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Resolve P1020 second USB controller multiplexing with eLBC
- mandatory to mention USB2 in hwconfig string to select it
over eLBC, otherwise USB2 node is removed
- works only for SPI and SD boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023RDS board is the reference board for the P1023 SoC.
Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe,
UART, I2C, etc.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If DDR initialziation uses a speed table and the speed is not matched,
print a warning message instead of silently ignoring.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Allow overriding RCW for all RDIMM, not only quad-rank ones.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection for qp_info and liodn associated with Q/BMan. Also
rearrange setting of _tbl_sz variables to utilize existing ifdef
protection for things like FMAN.
Also add protection around setup_portals() call in corenet_ds board
code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection in LAW & TLB code to handle the case in which
CONFIG_SYS_BMAN_MEM_PHYS or CONFIG_SYS_QMAN_MEM_PHYS arent defined for a
build.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove an empty board_early_init_f() from the MPC8323ERD and MPC360ERDK boards.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The clock-frequency property in an audio codec's device tree node is set to
the input clock frequency for that codec. On the Freescale P1022DS board,
the input clock is enabled only if the hwconfig 'audclk' option is set.
Therefore, the property should only be set in the device tree if the clock
is actually enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes the MX31ADS build by using the new relocation scheme.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Felix Radensky <felix@embedded-sol.com>
The boot cause code has been factor out to soc common
code,we need drop the part from the board support code
This patch also remove the redundant cpu version print
Signed-off-by: Jason Liu <jason.hui@linaro.org>
This patch add initial support for freescale MX53LOCO board.
Network(FEC),SD/MMC,UART have been supported by this patch
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Currently, some linker scripts are found by common code in config.mk.
Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is
sometimes in arch config.mk and sometimes in board config.mk. Some
are found using an arch-specific rule for looking in CPUDIR, etc.
Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL
when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact
that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds.
Replace all of this -- except for a handful of boards that are actually
selecting a linker script in a unique way -- with centralized ldscript
finding.
If board code specifies LDSCRIPT, that will be used.
Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used.
If neither of these are specified, then the central config.mk will
check for the existence of the following, in order:
$(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
$(TOPDIR)/$(CPUDIR)/u-boot.lds
Some boards (sc3, cm5200, munices) provided their own u-boot.lds that
were dead code, because they were overridden by a CPUDIR u-boot.lds under
the old powerpc rules. These boards' own u-boot.lds have bitrotted and
no longer work -- these lds files have been removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
Add the 'pixis_reset dump' command, which displays the contents of the PIXIS
registers. This command is only available if DEBUG is defined.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove an empty board_early_init_f() from the MPC8641HPCN board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration. Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.
The old definition of the "monitor" environment variable only determines
which video port to use for output. This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The
resolution was hard-coded into board-specific code. The Linux command-line
arguments needed to be hard-coded to the proper video definition string.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The P3041DS & P5020DS boards are almost identical (except for the
processor in them). Additionally they are based on the P4080DS board
design so we use the some board code for all 3 boards.
Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have
meaning on P3041DS/P5020DS. We utilize some of these for SERDES clock
configuration.
Additionally, the P3041DS/P5020DS support NAND.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: Jason Liu <r64343@freescale.com>
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: Stefano Babic <sbabic@denx.de>
