Commit graph

14889 commits

Author SHA1 Message Date
Tim Harvey
c9f7ef37f9 board: gateworks: venice: add imx8mm-gw7901 support
The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
 - i.MX8M Mini SoC
 - LPDDR4 DRAM
 - eMMC FLASH
 - SPI FRAM
 - Gateworks System Controller (GSC)
 - Atmel ATECC Crypto Authentication
 - USB 2.0
 - Microchip GbE Switch
 - Multiple multi-protocol RS232/RS485/RS422 Serial ports
 - onboard 802.11ac WiFi / BT
 - microSD socket
 - miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
 - Wide range DC power input
 - 802.3at PoE

To add support for this board:
 - add dts from Linux (accepted for v5.14)
 - add SPL PMIC config

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 18:12:41 +02:00
Teresa Remmet
bbf04b28d2 board: phytec: imx8mp-phycore: Switch to binman
Use now binman for image creation.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Teresa Remmet
fd82763cd2 board: phytec: phycore-imx8mp: Enable DVS1 control
Enable DVS1 control through PMIC_STBY_REQ.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-07-10 16:53:34 +02:00
Teresa Remmet
0f166b85ac board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V
Increase VDD_ARM to prevent timing issues as VDD_SOC is
used in OD mode. Also increase GIC clock.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-07-10 16:53:34 +02:00
Teresa Remmet
60f64bec41 board: phytec: phycore_imx8mp: Add fec support
Enable support for the fec ethernet on phyCORE-i.MX8MP.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Teresa Remmet
1feac813fe board: phytec: phycore_imx8mp: Change debug UART
With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Tim Harvey
c1f6fd2bb7 pci: imx: use reset-gpios if defined by device-tree
If reset-gpio is defined by device-tree use that if
CONFIG_PCIE_IMX_PERST_GPIO is not defined.

Note that after this the following boards which define
CONFIG_PCIE_IMX_PERST_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
 - mx6sabresd
 - mx6sxsabresd
 - novena
 - tbs2910
 - vining_2000

Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_PERST_GPIO and does
not have reset-gpios defined it it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_PERST_GPIO globally can't be done until that board adds
reset-gpios.

Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD)
Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD)
Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD)
Cc: Soeren Moch <smoch@web.de> (maintainer:TBS2910 BOARD)
Cc: Silvio Fricke <open-source@softing.de> (maintainer:VINING_2000 BOARD)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:34 +02:00
Tim Harvey
31273c5af5 imx: ventana: display 'none' for MMC if board does not have it
print 'None' instead of just a blank line if nothing is detected:
MMC:  None

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:34 +02:00
Tim Harvey
b57b14dc70 imx: ventana: add support for DLC0700XDP21LF LCD display
Add LVDS support for DLC0700XDP21LF 7in 1024x600 display
(equivalent to the DLC-700JMGT4 with new touch controller)

Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
e9284c03bc imx: ventana: display neteowrk PHY
Add displaying the detected network PHY on boot.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
9634c748b1 imx: ventana: add DP83867 PHY LED configuration
Add DP83867 PHY LED configuration.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
0545b17b69 imx: ventana: put LTC3676 regulators in continuous mode
In the default pulse-skipping mode regulators that are very lightly
loaded can fail to regulate properly. Switching them to always use
continuous mode causes only around 10mW of overall system power
difference in a lightly loaded system that isn't already operating
them in continuous mode.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
722d22813e imx: ventana: put PFUZ100 regulators in continuous mode
In the default 'auto' mode regulators that are very lightly loaded
can be put in PFM mode and fail to regulator properly. Switching them
to always use continuous PWM mode has a neglibable affect on system
power and garuntees proper regulation under lightly loaded circumstances.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
a32be88da0 imx: ventana: add PMIC fix for GW54xx-G
Substitutions in EOL parts changes the VDD_2P5 voltage rail such that
the previously unused VGEN6 LDO is needed in place of the lower power
VGEN5 for the GW54xx-G.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
729fd990c9 imx: ventana: remove unneeded includes
remove unnecessary includes

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Christoph Niedermaier
ac24244ba4 ARM: imx6: Update dhelectronics/dh_imx6/MAINTAINERS file
Adding new DH electronics mailing list and update list of maintainers.

Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
2021-07-10 15:57:33 +02:00
Tom Rini
490101a5e5 Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
Aside from the usual fixes and updates one visible change is the
MMC update, which fixes some lingering bugs and gives a decent speed
increase on some boards (9->19 MB/s on H6, 21->43 MB/s on A64 eMMC).
I am keeping an watchful eye on bug reports here, to spot any correctness
regressions.
Another change is finally the enablement of the first USB host port on
many boards without micro-USB (data) sockets, like the Pine64 family.
That doubles the number of usable USB ports from 1 to 2 on those boards.

Some smaller fixes, 4GB DRAM support (on the H616) and a new board (ZeroPi)
conclude this first round of changes.

Compile-tested for all 157 sunxi boards, boot-tested on Pine H64,
Pine64-LTS, OrangePi Zero 2 and BananaPi M2 Berry.

Summary:
- DT update for H3/H5/H6
- Enable first USB port on boards without micro-USB
- ZeroPi board support
- 4GB DRAM support for H616 boards
- MMC fixes and speed improvement
- some fixes
2021-07-09 21:08:52 -04:00
Andre Przywara
212224ed68 sunxi: board: Add H616 MMC2 pins
We hardcode the pinctrl setting for the MMC controllers in boards.c,
since we need them also in the SPL, where there is no DT yet.

Add the respective setting for the H616 SoC, to enable eMMC on boards
with this SoC as well.
Also to make diagnosing this problem easier, print a warning if a board
tries to setup MMC2 pins without a respective SoC setting being defined.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan at amarulasolutions.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec at siol.net>
2021-07-10 01:22:09 +01:00
Yu-Tung Chang
2527b24f39 sunxi: h3: Add initial ZeroPi support
ZeroPi is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner H3 SOC.

ZeroPi features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 256MB/512MB DDR3 RAM
- microsd slot
- 10/100/1000Mbps Ethernet
- Debug Serial Port
- DC 5V/2A power-supply

Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-07-10 01:22:09 +01:00
Tim Harvey
800433814a octeontx: do not require cavium BDK node to be present
The cavium,bdk node is a non-standard dt node used by the BDK and
therefore it is removed from the dt before booting Linux. Do not
require this node to exist as it won't for standard dt's.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-07-08 16:40:52 +02:00
Tom Rini
4ee73b00ba Revert "arm: Remove nsa310s board"
While this platform has not yet been converted, there is active efforts
to do so.  Keep the platform for now.

This reverts commit aa697e6904.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 22:55:41 -04:00
Tom Rini
7d0559910f sniper: Add build guards around MUSB support code
If MUSB support is disabled, these parts of the code will fail to build.

Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 22:22:42 -04:00
Tom Rini
570c3dcfc1 arm: Remove spear600 boards and the rest of SPEAr support
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.  As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.

Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 22:22:42 -04:00
Tom Rini
d7221d0d66 arm: Remove spear320 boards
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.  As this is
also the last SPEAR3XX platform, remove that symbol as well.

Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 22:22:42 -04:00
Tom Rini
1dc77c290f arm: Remove spear310 boards
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.

Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 22:22:42 -04:00
Tom Rini
0e377bbabb arm: Remove spear300 boards
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.

Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 22:22:42 -04:00
Tom Rini
aa697e6904 arm: Remove nsa310s board
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove it

Cc: Gerald Kerma <dreagle@doukki.net>
Cc: Tony Dinh <mibodhi@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 22:22:42 -04:00
Tom Rini
dee08b1999 arm: Remove gplugd board
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove it

Cc: Ajay Bhargav <contact@8051projects.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 22:22:42 -04:00
Tom Rini
bc08dc563e arm: Remove edb9315a board
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove it.

This is also the last PL010_SERIAL using board, so remove those
references.

Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 22:22:42 -04:00
Tom Rini
f4a6f75b48 arm: Remove at91rm9200ek boards
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.

Cc: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 22:22:42 -04:00
Tom Rini
ec6b37cef4 ppc: Remove T4160RDB board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.  As this is the last
ARCH_T4160 platform, remove that support as well.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:24 -04:00
Tom Rini
1567e3255d ppc: Remove MPC832XEMDS boards
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove them.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:24 -04:00
Tom Rini
6c332e2b8c ppc: Remove MPC8323ERDB board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:24 -04:00
Tom Rini
139ff3be23 ppc: Remove MPC8315ERDB board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.  As this is the last
ARCH_MPC8315 platform, remove that support as well.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:24 -04:00
Tom Rini
1c58857ad7 ppc: Remove sbc8641d board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.  This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.

Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-07-07 19:52:24 -04:00
Tom Rini
ed7fe2bee1 ppc: Remove xpedite boards
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove them.  As this includes
the last ARCH_MPC8572 platform, remove that as well.

Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
2021-07-07 19:52:24 -04:00
Tom Rini
66e3c64f2c ppc: Remove kmcoge4 board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.

Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:24 -04:00
Tom Rini
806968935c ppc: Remove MPC8568MDS board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.  As this is the last
ARCH_MPC8568 platform, remove that support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:23 -04:00
Tom Rini
6c3d99335c ppc: Remove T1023RBD boards and T1024RDB_SECURE_BOOT
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.  As this is
the only ARCH_T1023 platform left, remove that support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:23 -04:00
Tom Rini
98898601b4 ppc: Remove MPC8555CDS boards
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove them.  As this is the only
ARCH_MPC8555 platform left, remove that support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:23 -04:00
Tom Rini
a8571337d7 ppc: Remove MPC8541CDS board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.  As this is the only
MPC8541 target left, remove that architecture support as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:23 -04:00
Tom Rini
5fe4c0cc6e ppc: Remove TQM834x board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:23 -04:00
Tom Rini
bb656c687b ppc: Remove sbc8548 boards
These boards have not been converted to CONFIG_DM_PCI by the deadline and are
also missing conversion to CONFIG_DM.  Remove them.

Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:23 -04:00
Tom Rini
6843862342 ppc: Remove caddy2 / vme8349 boards
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.

Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:23 -04:00
Tom Rini
7458f18e5c ppc: Remove MPC8313ERDB boards
These boards have not been converted to CONFIG_DM_PCI by the deadline.
Remove them.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:23 -04:00
Tom Rini
af96210ae7 ppc: Remove ve8313 board
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.

Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
2021-07-07 19:52:23 -04:00
Tom Rini
b617d40c50 ppc: Remove mpc8308_p1m board
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.

Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:23 -04:00
Tom Rini
3588e20060 ppc: Remove sbc8349 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:23 -04:00
Tom Rini
9b7993bba9 m68k: Remove M5475x boards
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them.  As this is the last of the mcf547x_8x family of boards,
remove that support as well.

Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:22 -04:00
Tom Rini
eb83d10b42 m68k: Remove M5485 boards
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them.  As this is all of the CONFIG_M548x platforms as well,
remove that code.

Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:08 -04:00
Tom Rini
5b8a83551d Merge branch '2021-07-06-update-to-gcc11-clang11'
- Update CI to use gcc-11.1 and clang-11 to build everything.  This
  requires a few fixes to the code that these newer compilers have
  exposed.
2021-07-07 13:32:22 -04:00
Tom Rini
cb80ff20f2 bootstage: Eliminate when not enabled
When we do not have bootstage enabled, rather than include an empty
dummy function, we just don't reference it.  This saves us space in some
tight builds.  This also shows a few cases where show_boot_progress was
incorrectly guarded before.

Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 10:17:54 -04:00
Tom Rini
265724cb22 eb_cpu5282: Declare diplay_width / display_height as externs
The board code here references the display_width / display_height
variables set in the video driver, declare these as externs as gcc-11
will notice and lead to a multiple definition error.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 10:17:54 -04:00
Tom Rini
8627db79ca freescale: Drop unnecessary cpld_data_t non-typedef
In some board cpld.h files the definition of the cpld_data struct
not-quite makes a typedef for cpld_data_t.  This problem is caught with
gcc-11 as a multiple definition error.  As there are no users of this
non-typedef, fix this by not declaring it one to begin with.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 10:17:54 -04:00
Tianrui Wei
c9135d5a7a riscv: dts: add OpenPiton RISC-V board dts support
Previous device tree for OpenPiton emits a warning during compilation.
This commit fixes the previous warning adds dts to the OpenPiton RISC-V
board and added the device tree to MAINTAINER file.

Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-07 20:34:02 +08:00
Tom Rini
5617efd2c8 Merge branch '2021-07-06-platform-updates'
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
2021-07-06 18:10:10 -04:00
Trevor Woerner
ba621fe3a9 lpc32xx: ea-lpc3250devkitv2: enable i2c (DM)
Enable a DMed i2c driver for the ea-lpc3250devkitv2 board.
Include some sample commands/output for testing.

Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2021-07-06 14:12:15 -04:00
Trevor Woerner
faf78fd464 arm: lpc32xx: add EA LPC3250 DevKitv2 board support
Add basic support for running U-Boot on the Embedded Artists LPC3250
Developer's Kit v2 board by launching U-Boot from the board's s1l loader
(which comes pre-installed on the board).

Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2021-07-06 14:12:14 -04:00
Trevor Woerner
bd4dbf9e43 lpc32xx: Kconfig: switch to CONFIG_CONS_INDEX
There's nothing special or unique to the lpc32xx that requires its own config
parameter for specifying the console uart index. Therefore instead of using
the lpc32xx-specific CONFIG_SYS_LPC32XX_UART include parameter, use the
already-available CONFIG_CONS_INDEX from Kconfig.

Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-07-06 14:11:50 -04:00
Masami Hiramatsu
5cd4a355e0 board: synquacer: Add DeveloperBox 96boards EE support
Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
  https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
2021-07-06 14:11:50 -04:00
Linus Walleij
7dd42be9f9 ARM: integrator: Drop PCI support
We didn't convert the Integrator to use DM for PCI in
time, and we don't use it either so let's just drop
PCI support from the Integrator.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2021-07-06 14:07:36 -04:00
Sinan Akman
c8be85f3ff mpc8379erdb: enable DM_USB DM_PCI DM_ETH
Signed-off-by: Sinan Akman <sinan@writeme.com>
2021-07-06 14:07:36 -04:00
Zong Li
4b4159d0f3 board: sifive: support spl multi-dtb on unmatched board
There are two revisions of unmatched board with different DDR timing,
we'd like to support multi-dtb mechanism in SPL, then it selects the
right DTB at runtime according to PCB revision in I2C EEPROM.

Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-06 20:24:26 +08:00
Zong Li
05e254862f board: sifive: Add an interface to get PCB revision
There are different DDR parameter settings for different board
revisions. Add a new interface to get the PCB revision to determine
which DT should be selected at runtime.

Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-06 20:24:25 +08:00
Zong Li
e2172aa83d riscv: sifive: fu740: kconfig: Enable support for Opencores I2C controller
Enable the Opencores I2C controller on FU740

Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-06 20:24:25 +08:00
Zong Li
946afdf620 board: sifive: unmatched: add initial support for a platform ID EEPROM
Add initial support for the PCB description EEPROM for SiFive HiFive
Unmatched boards.

This implementation is refactored based on Paul Walmsley's porting and
adopt the suggestions from David Abdurachmanov.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-06 20:24:25 +08:00
Tianrui Wei
8a44fe6943 board: riscv: add openpiton-riscv64 SoC support
This patch adds openpiton-riscv64 SOC support. In particular, this
board supports a standard bootflow through zsbl->u-boot SPL->
opensbi->u-boot proper->Linux. There are separate defconfigs for
building u-boot SPL and u-boot proper

Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-06 13:50:56 +08:00
Tom Rini
6b69f15fd6 Xilinx changes for v2021.10
clk:
 - Add driver for Xilinx Clocking Wizard IP
 
 fdt:
 - Also record architecture in /fit-images
 
 net:
 - Fix plat/priv data handling in axi emac
 - Add support for 10G/25G speeds
 
 pca953x:
 - Add missing dependency on i2c
 
 serial:
 - Fix dependencies for DEBUG uart for pl010/pl011
 - Add setconfig option for cadence serial driver
 
 watchdog:
 - Add cadence wdt expire now function
 
 zynq:
 - Update DT bindings to reflect the latest state and descriptions
 
 zynqmp:
 - Update DT bindings to reflect the latest state and descriptions
 - SPL: Add support for ECC DRAM initialization
 - Fix R5 core 1 handling logic
 - Enable firmware driver for mini configurations
 - Enable secure boot, regulators, wdt
 - Add support xck devices and 67dr
 - Add psu init for sm/smk-k26 SOMs
 - Add handling for MMC seq number via mmc_get_env_dev()
 - Handle reserved memory locations
 - Add support for u-boot.itb generation for secure OS
 - Handle BL32 handoffs for secure OS
 - Add support for 64bit addresses for u-boot.its generation
 - Change eeprom handling via nvmem aliases
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYN105QAKCRDKSWXLKUoM
 IZiFAJ9CIiEpHiBbnAhA0VOMGoaXHGULywCdED/5dNgVtc1C7y4avzETbEyWzD4=
 =CdMa
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2021.10

clk:
- Add driver for Xilinx Clocking Wizard IP

fdt:
- Also record architecture in /fit-images

net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds

pca953x:
- Add missing dependency on i2c

serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver

watchdog:
- Add cadence wdt expire now function

zynq:
- Update DT bindings to reflect the latest state and descriptions

zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
2021-07-01 08:57:23 -04:00
T Karthik Reddy
45576273e9 xilinx: zynqmp: Add support for 67dr silicon
Add zynqmp 67dr silicon to zynqmp device id table.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-07-01 09:25:06 +02:00
Tom Rini
8fba49bc8e Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-sh into next
- V3U Falcon board support
2021-06-28 18:32:07 -04:00
Tom Rini
6d0453d889 Prepare v2021.07-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmDaJXgACgkQFHw5/5Y0
 tyySmwwAkW7GVAv+bXSd+8u1IsScl0QrSCoBdfHpdMcAME3gZmXqxClxskfbYJR/
 3IByQFlsn7j8HruR/49+etk0i0Pc4HNfynTLuAy+77/lh+h3Pnru/VPBhQqR7KW0
 NN5STn91QWLl74vRmx5wmEfSMhg7LTE1US8Rh6UXAd2dAiPd+hUawIR9D0Pq5Gzm
 nn7HvamDYspFUgSYYl8h1RtRQ9VqAFpnnPphpLkvX6323uCQwccXu5pnj1fLfGfj
 iO2Q+bDcwpEdUosox/LM1BdMoaSA+opOjk/e72y9V84+Jk6D+Jn5zQEpF5TJnTyI
 Yi2+NuJWS5xFWk1dnJrbGt0HpWM2oO12dZZ7eYy/FdsPJiWAS0ppRuxHVb868vjD
 ulca7acFPUjGyo3vBw1S0iVmPCBFGHBoyg3QLrUHYbpISeBeoa2w2cDxQl90ahw/
 TgRx+yutKfwkBPfILwDylNOgCGRwvLfroRyMEMiQ3gTSOCBmBX/yMv1k8tb9ZvPZ
 /WVsK6dw
 =F7x1
 -----END PGP SIGNATURE-----

Merge tag 'v2021.07-rc5' into next

Prepare v2021.07-rc5

# gpg: Signature made Mon 28 Jun 2021 03:39:36 PM EDT
# gpg:                using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate]

# Conflicts:
#	configs/am64x_evm_r5_defconfig
2021-06-28 16:22:13 -04:00
Koji Matsuoka
cdaa69c46e ARM: renesas: Add GICv3 initialization for V3U Falcon
Init GICv3 for V3U Falcon in early phase

Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-06-24 20:22:18 +02:00
Koji Matsuoka
b3494132f0 ARM: renesas: Add generic timer initialization for V3U Falcon
Init the Generic Timer for V3U Falcon in early phase

Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-06-24 20:22:18 +02:00
Hai Pham
4cfdcf3948 ARM: renesas: Add R8A779A0 V3U Falcon board code
Add board code for the R8A779A0 V3U Falcon board.

Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - various small rebase fixes and clean ups
2021-06-24 20:22:18 +02:00
Michal Simek
ce39ee28ec zynqmp: Do not place u-boot to reserved memory location
TF-A and SecureOS can allocate the part of DDR for self but U-Boot is not
handling this configuration that the part of memory is reserved and
shouldn't be used by U-Boot. That's why read all reserved memory locations
and don't use it.
The code was taken from commit 4a1b975dac ("board: stm32mp1: reserve
memory for OP-TEE in device tree") and commit 1419e5b516 ("stm32mp:
update MMU config before the relocation") which is used by stm32 and does
the job properly.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
476588c9b4 arm64: zynqmp: Handle MMC seq number based on boot device
K26 has EMMC and SD and default 0 is not working when system is booting out
of SD which is controller 1. Add controller autodetection via
mmc_get_env_dev(). The same code is used for distro_boot selection done in
board_late_init(). bootseq variable can't be reused because this is called
so late.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
02ac1553b8 arm64: zynqmp: Add psu_init_gpl for k26 boards
Add psu_init_gpl file for getting SPL to work directly from the tree.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
ddf8deabc3 arm64: zynqmp: Add support for SVD devices
SVDs  are using different name which can't be handled via zynqmp_devices
structure. That's why introduce zynqmp_detect_svd_name() which checks ID
code for these devices and show proper name for them.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Tom Rini
28afb71646 Merge tag 'u-boot-rockchip-20210618' of https://source.denx.de/u-boot/custodians/u-boot-rockchip into next
- New SoC platform support: rk3568;
- rockchip pcie Code compile issue fix;
- Board fix for rk3399 Khadas Edge;
- Add Rockchip NFC driver;
2021-06-19 08:20:12 -04:00
Patrick Delaunay
486808e354 board: stm32mp1: correct the property name for eth
Use the correct name for STMicroelectronics phys config properties,
replace '_' by '-':
  "st,eth_clk_sel" => "st,eth-clk-sel"
  "st,eth-ref-clk-sel" => st,eth-clk-sel"

These property name are aligned with the upstreamed Linux kernel binding:
 linux/Documentation/devicetree/bindings/net/stm32-dwmac.yaml

See Linux kernel commit "dt-bindings: net: stmmac: add phys config
properties" merged in v5.1-rc1.

This patch allow to reuse the kernel device tree directly in U-Boot.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-06-18 10:09:41 +02:00
Joseph Chen
695693b2d0 board: rockchip: Add rk3568 evb support
Add support for rk3568 evaluation board.

Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-06-18 14:36:24 +08:00
Tom Rini
a94b2aad05 First set of u-boot-atmel features for the 2021.10 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDLD78cHGV1Z2VuLmhy
 aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLhSB/0UqOd+Ujf2meiHU9yr
 oOOCLxVTjTUfIZKLad/zwlj2Xqzsjs6XMawC95BgouvkQLmj/gwerRWcZPg9l7/X
 hvb9VJi+iJoLRRpBPbeF3bMb92kCE+YZodFXyutlcY+Z0ZB9755zoVgR6ccKfksd
 Xp2y8AFptfYQNZ1l0yb3lhm1261CldWALrGTjRpY2hQ8nEMbV8z6WUB1hAF9CECa
 PGbKaiqm9OdktwHsLy4cYFFCuzkykn6T3P6ODineP7IxgEgZKTfJClSTFGY9S0GQ
 kwd7K/7j0W3rI5NPknB+Fb4IFAaTs/oozR+5ml7j+2S3G5GXjSGx8zaSOmOZvpP3
 KxwN
 =/I5V
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next

First set of u-boot-atmel features for the 2021.10 cycle:

This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
2021-06-17 11:46:44 -04:00
Tom Rini
a298d4fbcd Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- fsl-qoriq: Bug fixes related pfe, eth, thermal node, vid.c, cpu release,
  mmc, usb, env, etc for Layerscape boards
- powerpc: Update Maintainers for some boards.
2021-06-17 08:44:56 -04:00
Priyanka Jain
b7efcaff8b board: freescale: t1028xrdb: Add MAINTAINER for revD
Add Priyanka Jain as MAINTAINER for
 T2080RDB_revD_defconfig,
 T2080RDB_revD_NAND_defconfig,
 T2080RDB_revD_SDCARD_defconfig and
 T2080RDB_revD_SPIFLASH_defconfig

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 12:52:54 +05:30
Camelia Groza
13ea307f79 board: freescale: t208xrdb: add a config option for rev D dts fixups
Under DM, we rely on u-boot's device tree to provide the correct PHY
addresses. The board_fix_fdt callback is intended to be used for
device tree fixups before relocation. Unfortunately, this isn't an
option when booting from flash since the device tree isn't writable
before relocation.

This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a
board revision D or up is the target. The config option is used to set
the correct Aquantia PHY address in the board's u-boot device tree.

Defconfig files with the option enable explicitly are added for
convenience.

Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Camelia Groza
4e21a555c1 board: freescale: t208xrdb: add Linux fdt fix-ups for rev D
The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs
connected to MAC1 and MAC2. The second Aquantia PHY is located at a
different address on the MDIO bus compared to rev C (0x8 instead of 0x1).

Fix-up the Linux device tree to update the PHY address for the second
Aquantia PHY on boards revisions D and up. Also rename the PHY node to
reflect the changes.

Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Camelia Groza
c91b130554 board: freescale: t208xrdb: detect the board revision version
Detect and print the board revision version based on the CPLD registers.

Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Camelia Groza
a484f7c486 board: freescale: t208xrdb: remove the legacy non-DM_ETH code
Both DM_ETH and DM_PCI are enabled for the T2080RDB board. Remove the
board_eth_init() callback and the non-DM_ETH code paths since they are not
needed anymore.

Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Aleksandar Gerasimovski
02802eb89e pg-wcom-ls102x: initialize front led and app buf
This patch adds the front led initialization and the application
buffer enable to the eraly board inititlaization.

Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Aleksandar Gerasimovski
fbb0e15a42 km/scripts: fix saveenv command syntax
This is most probably a typo, and in older u-uboot versions is same as
'saveenv', in the newer uboot versions there is a separate 'save' command
that is different from 'saveenv'.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Aleksandar Gerasimovski
3aea3ddf21 km/ls102xa: add support for u-boot POST memory test
From production view this is standard test executed during production on
all linux based foxmc cards.
On CENT2 HW defined memory region is zero means that some DDR accesses are
done by memory_post_dataline and memory_post_addrline but pattern tests
are skipped that's why mem_regions is fast there.

On ls102x for the complete DDR region of 1GiB memory_regions_post_test
takes approx. 4min and this is too much for production, so this patch
defines only 1MiB region as compromise.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Aleksandar Gerasimovski
a7fd6fa1c2 board/km: add support for expu1 design based on nxp
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.

The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.

Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Priyanka Jain
0b036d4c1b board: freescale: t102xrdb: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for t102xrdb board.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Priyanka Jain
eccf98f8d8 board: freescale: p2041rdb: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for p2041rdb board.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Priyanka Jain
6d1657b998 board: freescale: p1_p2_rdb_pc: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for p1_p2_rdb_pc board.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Priyanka Jain
0eb946ec28 board: freescale: t4rdb: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for t4rdb board.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Aleksandar Gerasimovski
0753603e25 keymile: common: fix hexadecimal env variable format
Commit df86d32 breaks linux kernel and product application boot.

Linux kernel and our product application scripts are expecting 0x prefix
for hexadecimal values, while env_set_hex writes them without a prefix.

This patch partially revert env_set_hex usage for affected env variables.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Priyanka Singh
c0eeb730f8 board: freescale: vid.c: Add check for return value of adjust_vdd()
Add check for return value of adjust_vdd()

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Sean Anderson
55dac94ab8 k210: Don't imply CCF
Now that the k210 clock driver does not depend on CCF, we should no longer
imply it (and probably should not have in the first place). We can also
reduce the pre-relocation malloc arena back to something sensible.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-06-17 09:40:58 +08:00
Tom Rini
b2c4b7f665 u-boot-imx-20210616
-------------------
 
 - imxrt : fixes, USB, imxrt1020-evk
 - imx8m:
 	fix for verdin-imx8mm
 	Add conga-QMX8 board
 - imx6 :
 	documentation for pico-imx6:
 	Add SeeedStudio NPI-IMX6ULL Support
 	ventana: DM PCI
 - imx7d:
 	added SMEGW01 board
 
 CI : https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7765
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYMoTAg8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76aaXgCfa0IWXD0nOT0xQ50aKZGD3fspahsAn3rfnviv
 HnrT4j7bdBRksuYJ15PR
 =NEGm
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20210616' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20210616
-------------------

- imxrt : fixes, USB, imxrt1020-evk
- imx8m:
	fix for verdin-imx8mm
	Add conga-QMX8 board
- imx6 :
	documentation for pico-imx6:
	Add SeeedStudio NPI-IMX6ULL Support
	ventana: DM PCI
- imx7d:
	added SMEGW01 board

CI : https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7765
2021-06-16 11:18:11 -04:00
Mian Yousaf Kaukab
864c3dbc0a ls1012a: net: pfe: remove pfe stop from bootcmd
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.

Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.

Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-16 18:14:08 +05:30
Pali Rohár
029bb91e80 arm: mvebu: turris_{omnia, mox}: ensure running bootcmd_rescue always works
One of the points of putting the rescue boot command into default
environment is that user can invoke it without physical access to the
board (without having to press the factory reset button), by running
  run bootcmd_rescue
in U-Boot's console.

Therefore we have to ensure that bootcmd_rescue is always set to default
value, regardless of whether the factory reset button was pressed.
Otherwise the variable will be empty for example after upgrade from
previous U-Boot.

Fixes: ec3784d626 ("arm: mvebu: turris_mox: add support for board rescue mode")
Fixes: 176c3e7760 ("arm: mvebu: turris_omnia: support invoking rescue boot from console")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-06-15 07:21:54 +02:00
Michael Opdenacker
ea83ea5afd board: sama5d3_xplained: add Falcon boot support
This supports Falcon boot support for Microchip SAMA5D3 Xplained,
tested on raw MMC, and on raw NAND.

spl_start_uboot() is has the simplest possible implementation.
It doesn't test the environment because enabling environment support
currently causes the SPL to exceed its maximum size (64 KiB).
It doesn't check the serial for incoming characters either because
this functionality currently doesn't seem to work from the SPL
on this board.

Settings for Falcon boot from at FAT partition are also added to
avoid compile failures when CONFIG_SPL_OS_BOOT is enabled, but this
particular case is currently not functional as adding FAT and
partition support cause the SPL to be too big again.

Signed-off-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
2021-06-14 12:28:03 +03:00
Tom Rini
c4737cd594 Xilinx changes for v2021.07-rc5
zynqmp:
 - Fix ANALOG_BUS value after powerup
 - Disable EFI_CAPSULE_ON_DISK_EARLY
 
 zynqmp-gqspi:
 - Fix write issue
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYMNGPAAKCRDKSWXLKUoM
 IUCCAJ4lktDK3MTBAJUMHzKXvzt1jcuW6wCfQKuoQSETBDuy1LMXV6uxQXkrHJA=
 =IXXl
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.07-rc5' of https://source.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx changes for v2021.07-rc5

zynqmp:
- Fix ANALOG_BUS value after powerup
- Disable EFI_CAPSULE_ON_DISK_EARLY

zynqmp-gqspi:
- Fix write issue
2021-06-11 08:29:34 -04:00
Tero Kristo
c3ebc56e2d board: ti: j72xx: README: update build instructions and image formats
Update build instructions and image formats based on HSM rearch. A new
DM image is added into the build, which gets executed right after R5
SPL finishes its job.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
2021-06-11 16:34:52 +05:30
Lokesh Vutla
481d394e77 common: fit: Update board_fit_image_post_process() to pass fit and node_offset
board_fit_image_post_process() passes only start and size of the image,
but type of the image is not passed. So pass fit and node_offset, to
derive information about image to be processed.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
2021-06-11 16:34:52 +05:30
Adrian Fiergolski
3414712ba8 arm64: zynqmp: Writing correct value to ANALOG_BUS
The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].

[1] https://github.com/Xilinx/embeddedsw

Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-11 09:24:58 +02:00
Marek Behún
45853413e2 arm: mvebu: turris_mox: start blinking PHY LEDs when entering rescue
Configure blinking on ethernet PHY LEDs on the MOX A board when entering
rescue mode via reset button.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-06-10 07:18:06 +02:00
Marek Behún
ec3784d626 arm: mvebu: turris_mox: add support for board rescue mode
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.

In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.

Rescue boot from console can be invoked by running
  run bootcmd_rescue

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-06-10 07:18:06 +02:00
Pali Rohár
e61a4ff13f Nokia RX-51: Enable CONFIG_WDT to remove deprecation warning
Also convert CONFIG_HW_WATCHDOG to CONFIG_WATCHDOG.

Signed-off-by: Pali Roh?r <pali@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210309201915.16586-1-pali@kernel.org
2021-06-09 22:23:44 +05:30
Aswath Govindraju
397d7b0fae board: ti: am64x: Set the core voltage of USB PHY to 0.85V
Set the core voltage of USB PHY in AM64x to 0.85V in spl_board_init().

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-5-a-govindraju@ti.com
2021-06-09 22:23:44 +05:30
Fabio Estevam
40496ac3b7 mx7d: Add Storopack's SMEGW01 board
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.

Based on the original U-Boot work done by Phytec.

Signed-off-by: Fabio Estevam <festevam@denx.de>
2021-06-09 13:34:38 +02:00
Navin Sankar Velliangiri
a3a0bc85c0 imx: Add SeeedStudio NPI-IMX6ULL Support
CPU:   Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 49C
Reset cause: POR
Model: Seeed NPi iMX6ULL Dev Board with NAND
Board: Seeed NPi i.MX6ULL Dev Board
DRAM:  512 MiB
NAND:  512 MiB
MMC:   FSL_SDHC: 0
In:    serial@2020000
Out:   serial@2020000
Err:   serial@2020000
Net:   FEC0

Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host

Signed-off-by: Navin Sankar Velliangiri <navin@linumiz.com>

Note:

Changes in v2:

 * removed unnecessary space in imx6ull-seeed-npi-imx6ull-dev-board.dts file.
 * Used SZ_2M for CONFIG_SYS_MALLOC_LEN size allocation.
2021-06-09 13:34:18 +02:00
Oliver Graute
fe133eb192 imx: support for conga-QMX8 board
Add i.MX8QM qmx8 congatec board support

U-Boot 2021.07-rc3-00528-gc9a966d9dd (May 31 2021 - 15:21:25 +0200)

CPU:   NXP i.MX8QM RevB A53 at 1200 MHz

Model: Congatec QMX8 Qseven series
Board: conga-QMX8
Build: SCFW 494c97f3, SECO-FW d63fdb21, ATF 09c5cc9
Boot:  SD2
DRAM:  6 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial@5a060000
Out:   serial@5a060000
Err:   serial@5a060000
switch to partitions #0, OK
mmc2 is current device
Net:
Error: ethernet@5b040000 address not set.
No ethernet found.

Hit any key to stop autoboot:  0

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
2021-06-09 13:34:09 +02:00
Fabio Estevam
b8916306d1 pico-imx6: README: Fix the boot mode settings URL
The original URL that explains the boot mode setting is no longer
valid.

Update to the new one.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-06-09 13:33:45 +02:00
Tim Harvey
cd18f1e6e6 imx: ventana: enable dm support for PCI and FEC ethernet
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.

Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.

Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-06-09 13:33:35 +02:00
Oleh Kravchenko
1180baec98 Add EV-iMX280-NANO-X-MB board
A simple prototyping board with one microSD port, one Ethernet port,
2 USB ports, I2C, SPI, GPIO, and UART interfaces.

Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
2021-06-09 13:32:49 +02:00
Oleh Kravchenko
3675ac081a Add out4.ru O4-iMX-NANO board
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.

Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
2021-06-09 13:32:42 +02:00
Anatolij Gustschin
ac36dc7d19 brxre1: disable video after DM_VIDEO conversion deadline
The board was not converted to DM_VIDEO before deadline, so disable
video support for now.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2021-06-05 10:40:47 +02:00
Marek Behún
176c3e7760 arm: mvebu: turris_omnia: support invoking rescue boot from console
Make it possible to invoke rescue boot from U-Boot console, without
having to press the factory reset button. This is needed when accessing
the device remotely, for example.

Achieve this by putting rescue command into `bootcmd_rescue` default
environment variable and setting some distroboot environment variables
to their default values when the factory button is pressed.

Rescue boot from console can be invoked by running
  run bootcmd_rescue

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-06-04 11:32:41 +02:00
Marek Behún
0b5bb36d13 arm: mvebu: turris_omnia: update rescue mode boot command
Update rescue mode boot command on Turris Omnia. We are compressing the
image with lzma now.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-06-04 11:32:41 +02:00
Green Wan
70415e1e52 board: sifive: add HiFive Unmatched board support
Add defconfig and board support for HiFive Unmatched.

Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-31 16:35:55 +08:00
Marek Vasut
5c54260130 ARM: stm32: Add additional ID register check for KSZ8851 presence
Currently the code sets eth1addr only if /ethernet1 alias exists in DT,
the node pointed to by the alias has "micrel,ks8851-mll" compatible
string, and the KSZ8851 CCR register read indicates programmed EEPROM
is not connected.

This is not sufficient to detect cases where the DT still contains the
KSZ8851 nodes, but the chip itself is not present. Extend the detection
to handle these cases.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-05-28 14:54:16 +02:00
Christoph Niedermaier
5c38c06ec0 ARM: stm32: Update dhelectronics/dh_stm32mp1/MAINTAINERS file
Adding new DH electronics mailing list.

Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-05-28 14:38:47 +02:00
Daniel Schwierzeck
5308a71db8 MIPS: remove deprecated qemu_mips board
Remove qemu_mips boards because DM migration doesn't make sense.
The board support for qemu_mips is already marked as deprecated
in Qemu in favour of the Malta board. Also qemu_mips support
has been removed from Linux a long time ago.

The official replacement is the Malta board. The same Malta U-Boot
image can be used with Qemu and on physical hardware.
All combinations of Big Endian and Little Endian as well as 32 bit
and 64 bit are supported.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2021-05-25 15:35:06 +02:00
Marek Behún
79dec66ca7 ARM: fix LTO for rockchip and samsung
When building with LTO, the compiler complains about type mismatch of
function usb_gadget_handle_interrupts(). This function is defined
without parameters in files
  arch/arm/mach-rockchip/board.c
  board/samsung/common/exynos5-dt.c
but it should have one parameter, int index.

Fix this.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-05-24 14:21:30 -04:00
Marek Behún
236f2ec432 treewide: Convert macro and uses of __section(foo) to __section("foo")
This commit does the same thing as Linux commit 33def8498fdd.

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-05-24 14:21:30 -04:00
Bin Meng
cc269e1c00 riscv: ae350: Switch to use binman to generate u-boot.itb
Use the new BINMAN_STANDALONE_FDT option for AE350 based SPL defconfigs,
so that binman is now used to generate u-boot.itb.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-19 17:01:51 +08:00
Bin Meng
0784510f74 riscv: sifive: unleashed: Switch to use binman to generate u-boot.itb
At present SiFive Unleashed board uses the Makefile to create the FIT,
using USE_SPL_FIT_GENERATOR, which is deprecated as per the Makefile
warning. Update to use binman instead.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-05-19 17:01:50 +08:00
Sughosh Ganu
6a2e26b95f efi_loader: capsule: Remove the check for capsule_authentication_enabled environment variable
The current capsule authentication code checks if the environment
variable capsule_authentication_enabled is set, for authenticating the
capsule. This is in addition to the check for the config symbol
CONFIG_EFI_CAPSULE_AUTHENTICATE. Remove the check for the environment
variable. The capsule will now be authenticated if the config symbol
is set.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviwed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-05-18 12:36:12 +02:00
Konstantin Porotchkin
e1c55dfc7b arm: octeontx2: Add Octeon TX2 CN913x DB support
This patch adds the base support for the Marvell Octeon TX2 CN913x DB.
Only one defconfig is added with this patch. Other board variants are
available (NAND, MMC booting) and images for these boards can be
generated by following the documentation added in the included README.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2021-05-16 06:48:45 +02:00
Tom Rini
8054d80b04 Merge https://source.denx.de/u-boot/custodians/u-boot-sh 2021-05-14 23:00:24 -04:00
Sean Anderson
2d64e3829b riscv: k210: Rename airam to aisram
This is more consistent with the naming of other ram banks, and matches
what Linux is doing.

Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
2021-05-14 16:20:49 +08:00
Sean Anderson
23058052de riscv: Enable AI ram on K210
We just need to initialize all the clocks pre-reloc. The clock driver
creates a bunch of devices, so we need to increase the pre-reloc malloc
arena.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
2021-05-14 16:20:49 +08:00
Kory Maincent
1569847e7c am335x: add support for cape detect functionality
Update the Kconfig and the board file to make the am335x board compatible
with cape detection.

Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
2021-05-13 13:09:09 -04:00
Kory Maincent
d705527a89 arm: am335x: add support for i2c2 bus
The am335x from BeagleBone use i2c EEPROM to detect capes.
The memory is wired to i2c bus 2 therefore it need to be enabled.

Add i2c2 clock, pinmux description and pinmux enable function.

Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
2021-05-13 13:09:09 -04:00
Kory Maincent
6c2c7e9cb9 arm: sunxi: add support for DIP detection to CHIP board
Add the extension_board_scan specific function to scan the information
of the EEPROM on one-wire and fill the extension struct.
Add the Kconfig symbol to enable the needs to detect DIPs.

Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Andre Przywara <andre.przywara@arm.com>
2021-05-13 13:09:09 -04:00
Kory Maincent
0705e25cd0 am57xx: add support for cape detect functionality
This commit enables using the extension board detection mechanism on
AM57xx based platforms.

Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
2021-05-13 13:09:09 -04:00
Kory Maincent
8c1d443206 ti/common: add support for extension_scan_board function
The BeagleBone platforms all use a common mechanism to discover and
identify extension boards (called "capes"): each extension board has an
I2C-connected EEPROM describing itself.

This patch implements a generic extension_scan_board() feature that can
be used by all BeagleBone platforms to read those I2C EEPROMs and fill
in the list of "extension" structures.

Following commits will enable this common logic on two BeagleBone
platforms.

Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
2021-05-13 13:09:09 -04:00
Kory Maincent
95300f203f pytest: add sandbox test for "extension" command
This commit extends the sandbox to implement a dummy
extension_board_scan() function and enables the extension command in
the sandbox configuration. It then adds a test that checks the proper
functionality of the extension command by applying two Device Tree
overlays to the sandbox Device Tree.

Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
[trini: Limit to running on sandbox]
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-05-13 13:09:09 -04:00
Ilko Iliev
4bf3a3fc39 board: pm9263: fix some typos in comments
Fix comment typos

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
2021-05-13 09:55:05 +03:00
Ilko Iliev
8ad3a77a74 board: pm9263: switch to use DM_ETH
Enable CONFIG_DM_ETH in configs/pm9263_defconfig
Drop legacy initialization in board/ronetix/pm9263.c
Remove network related setting from include/configs/pm9263.h

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
2021-05-13 09:55:04 +03:00
Ilko Iliev
f822b62c02 board: pm9261: remove network support
The network support is removed because there is
no DM for Davicom DM9000.

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
2021-05-13 09:55:04 +03:00
Marek Vasut
8f76c9d73a ARM: renesas: Scrub duplicate memory nodes from DT on Gen3
Scrub duplicate /memory@* node entries here. Some R-Car DTs might
contain multiple /memory@* nodes, however fdt_fixup_memory_banks()
either generates single /memory node or updates the first /memory
node. Any remaining memory nodes are thus potential duplicates.

However, it is not possible to delete all the memory nodes right
away, since some of those might not be DRAM memory nodes, but some
sort of other memory. Thus, delete only the memory nodes which are
in the R-Car3 DBSC ranges.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-05-12 21:36:27 +02:00
Marek Vasut
bd83431ea3 ARM: rmobile: Add missing rcar-common/common.c to Beacon RZG2M kit
The rcar-common/common.c contains various common board functions shared
by all R-Car and RZG boards. This board is not compiling the file in, so
add it. This way, part of the board code can be de-duplicated too.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
2021-05-12 21:36:27 +02:00
Tom Rini
ea184cbff9 Merge tag 'ti-v2021.07-rc3' of https://source.denx.de/u-boot/custodians/u-boot-ti
- Initial support for AM64 EVM and SK
- K3 DDR driver unification for J7 and AM64 platforms.
- Minor fixes for TI clock driver
2021-05-12 10:07:21 -04:00
Vignesh Raghavendra
ec658e7ee5 board: ti: am64x: Parse MAC address from board EEPROM
Parse MAC addresses from EEPROM and set them in the env. This is needed
to get MAC address for additional ethernet ports on the EVM.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2021-05-12 16:36:38 +05:30
Lokesh Vutla
7ecca0c43d configs: am64x_evm_a53: Enable support for reading eeprom
Enable relevant configs for reading eeprom data and updating env
variables.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-05-12 16:36:38 +05:30
Lokesh Vutla
63d825e9fc board: ti: am64x: Add support for detecting multiple device trees
Update the board_fit_config_name_match() to choose the right dtb.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-05-12 16:32:44 +05:30
Lokesh Vutla
8817c132a0 board: ti: am64x: Enable support for reading EEPROM in R5 SPL
Include the relevant configs to enable support for reading EEPROM in
R5SPL.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-05-12 16:32:44 +05:30
Lokesh Vutla
2ee76314a7 board: ti: am64x: Add support for reading eeprom data
I2C EEPROM data contains the board name and its revision.
Add support for:
- Reading EEPROM data and store a copy at end of SRAM
- Updating env variable with relevant board info
- Printing board info during boot.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-05-12 16:32:44 +05:30
Dave Gerlach
d411f0973a arm: mach-k3: am642: Add support for triggering ddr init from SPL
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2021-05-12 16:31:16 +05:30
Dave Gerlach
db2438131d ram: k3-ddrss: Introduce top-level CONFIG_K3_DDRSS
Create a new CONFIG_K3_DDRSS option to select the common parts of the
k3-ddrss driver. Also introduce a choice that depends on the top level
option to select CONFIG_K3_J721E_DDRSS for j721e support, and update
corresponding Kconfig as required.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2021-05-12 16:30:52 +05:30
Dave Gerlach
55afd2d8f5 configs: am64x_evm_a53: Add Initial support
Add initial A53 defconfig support for AM64x SoCs.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2021-05-12 16:30:28 +05:30
Dave Gerlach
d480bd5edc configs: am64x_evm_r5: Add Initial support
Add initial R5 defconfig support for AM64x SoCs.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2021-05-12 16:30:28 +05:30
Dave Gerlach
33b7258947 board: ti: am64x: Add board support for am64x evm
Add board specific initialization for am64x based boards.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2021-05-12 16:27:57 +05:30
Tom Rini
59a2b9e605 u-boot-imx-20210502
-------------------
 
 - mx6:   fixes for Ventana
 -        local fixes from maintainer
 - imx7d: Ronetix's iMX7-CM
 - imx8:  Ronetix iMX8MQ-CM
 	 Engicam i.Core MX8M
 	 Compulab iot-gate-imx8
 - Fixes i.MX8 documentation
 - Fixes phy usage with fec
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYJqX/Q8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76aACgCfYnzkeOHsKM6i9J6bdxIwwnU5NycAniDYksOG
 IT8LzFNHf0ECCj26S9mI
 =wVb3
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20210502' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20210502
-------------------

- mx6:   fixes for Ventana
-        local fixes from maintainer
- imx7d: Ronetix's iMX7-CM
- imx8:  Ronetix iMX8MQ-CM
	 Engicam i.Core MX8M
	 Compulab iot-gate-imx8
- Fixes i.MX8 documentation
- Fixes phy usage with fec
2021-05-11 12:23:11 -04:00
Tom Rini
2684e082bc ppc: Remove some SECURE_BOOT defconfigs
These specific configs are missing a number of migrations.  In addition,
they are blocking completion of the now-expired DM_MMC migration as it
requires enabling BLK.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-05-11 09:14:56 -04:00
Ilko Iliev
7666cccf4f ARM:imx:imx8mq-cm: Add support for Ronetix iMX8MQ-CM
Supported peripherals: Ethernet, eMMC, Serial.

U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2

U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)

CPU:   Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM:  1 GiB
WDT:   Started with servicing (60s timeout)
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In:    serial
Out:   serial
Err:   serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot:  0
u-boot=>

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
2021-05-02 12:46:54 +02:00
Ilko Iliev
fdd2f359e4 imx: Add support for Ronetix's iMX7-CM board
Console boot log:

U-Boot SPL 2021.04-00836-ga6232e065d-dirty (Apr 16 2021 - 15:16:35 +0200)
Trying to boot from MMC1

U-Boot 2021.04-00836-ga6232e065d-dirty (Apr 16 2021 - 15:16:35 +0200)

CPU:   Freescale i.MX7D rev1.3 1000 MHz (running at 792 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 44C
Reset cause: POR
Model: Ronetix iMX7-CM Board
Board: iMX7-CM
DRAM:  512 MiB
PMIC:  PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC:   FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial
Out:   serial
Err:   serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address - fe:be:37:01:5a:3f
eth0: ethernet@30be0000
Hit any key to stop autoboot:  0

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
2021-05-02 12:46:54 +02:00
Priit Laes
f94ce9eb05 imx: imx8: Update README with somewhat correct firmware versions
Current setup instructions for i.MX8QM MEK board include somewhat
conflicting instructions, so here's an attempt to fix it.

After trying both sets of firmwares, I can conclude that both of
them fail to work:

- no boot at all with imx-sc-firmware-0.7 / firmware-imx-7.6

- partial success with imx-sc-firmware-1.1 / firmware-imx-8.0:

U-Boot 2021.04-rc3-00135-ge0669a43c8 (Mar 08 2021 - 16:49:08 +0200)

CPU:   NXP i.MX8QM RevB A53 at 1200 MHz

Model: Freescale i.MX8QM MEK
Board: iMX8QM MEK
mu_hal_receivemsg timeout
Build: SCFW 65afe5f6, SECO-FW 65afe5f6, ATF a-20190
mu_hal_receivemsg timeout
sc_misc_get_boot_dev: res:16
Boot:  SD0
DRAM:  mu_hal_sendmsg timeout
sc_rm_is_memreg_owned: mr:0 res:21
...

Signed-off-by: Priit Laes <priit.laes@paf.com>
2021-05-02 12:46:54 +02:00
Ying-Chun Liu (PaulLiu)
53b516c58d arm: imx8m: add support for Compulab iot-gate-imx8 (imx8mm-cl-iot-gate)
Add initial support for Compulab iot-gate-imx8 board (imx8mm-cl-iot-gate).
The initial support includes:
 - MMC
 - eMMC
 - I2C
 - FEC
 - Serial console

Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Peter Robinson <pbrobinson@gmail.com>
2021-05-02 12:46:54 +02:00
Tim Harvey
1afa31a41e imx: ventana: add delay before reading EEPROM
fixes: d863d05439 ("imx: ventana: convert U-Boot to OF_CONTROL using FIT image")

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-05-02 12:46:54 +02:00
Jagan Teki
7e0daa924a board: imx8mm: Add Engicam i.Core MX8M Mini C.TOUCH 2.0
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.

Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector

i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.

i.Core MX8M Mini needs to mount on top of this Carrier board for
creating complete i.Core MX8M Mini C.TOUCH 2.0 board.

Linux dts commit details:

commit <a142252061ff> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
C.TOUCH 2.0")

Add support for it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2021-05-02 12:46:54 +02:00
Jagan Teki
e3409a4cb7 board: imx8mm: Add Engicam i.Core MX8M Mini EDIMM2.2 Starter Kit
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.

Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out

i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.

i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.

Linux dts commit details:

commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")

Add support for it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2021-05-02 12:46:54 +02:00
Sebastian Reichel
512bda95ed board: ge: bx50v3: fix crystal bit
The DA9063 enables the CRYSTAL bit by default, but there is no
crystal populated on the BA16 system on module. Without explicitly
clearing the CRYSTAL bit the system runs unstable and sometimes
reboots unexpectedly.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-05-02 12:46:54 +02:00
Tom Rini
f3a0d2c1af Xilinx changes for v2021.07-rc2
xilinx:
 - Enable saving variables based on bootmode
 - Cleanup usb dfu setup and wire it up with usb bootmode
 - Fix bootscript address logic
 - Remove GD references (spi, Versal)
 - Enable capsule update
 
 clk:
 - Small Kconfig fix
 
 net:
 - Fix gmii2rgmii bridge binding
 
 usb:
 - Propagate error (dfu gadget)
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYIqrgAAKCRDKSWXLKUoM
 IY86AJ9X9G6IwfnhHFWhManDrzPoBGaSBwCfVjMzPQcCddlGAW8UJ1NaPCLPPNc=
 =ACHF
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.07-rc2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx changes for v2021.07-rc2

xilinx:
- Enable saving variables based on bootmode
- Cleanup usb dfu setup and wire it up with usb bootmode
- Fix bootscript address logic
- Remove GD references (spi, Versal)
- Enable capsule update

clk:
- Small Kconfig fix

net:
- Fix gmii2rgmii bridge binding

usb:
- Propagate error (dfu gadget)
2021-04-29 11:31:06 -04:00
Igal Liberman
2dbba24088 phy: marvell: rename comphy related definitions to COMPHY_XX
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.

This patch does the following changes:
 - PHY_TYPE_XX --> COMPHY_TYPE_XX
 - PHY_SPEED_XX --> COMPHY_SPEED_XX

This improves readability, no functional change.

Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
2021-04-29 07:45:24 +02:00
Konstantin Porotchkin
c405226c34 arm: octeontx2: Add Octeon TX2 CN9130 CRB support
This patch adds the base support for the Marvell Octeon TX2 CN9130 CRB.
Not all interfaces are supported fully yet.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2021-04-29 07:45:13 +02:00
Stefan Roese
5d2d5c4f23 mips: octeon: Add Octeon III NIC23 board support
This patch adds the basic support for the PCIe target board equipped
with the Octeon III CN2350 SoC.

Signed-off-by: Stefan Roese <sr@denx.de>
2021-04-28 10:05:12 +02:00
Aaron Williams
6a453e50c3 mips: octeon: octeon_ebb7304: Add board specific QLM init code
This patch adds the board specific QLM/DLM init code to the Octeon 3
EBB7304 board. The configuration of each port is read from the
environment exactly as done in the 2013 U-Boot version to keep the
board and it's configuration compatible.

Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2021-04-28 10:05:12 +02:00
Tom Rini
4dda435131 - MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
 - MIPS: octeon: add support for AHCI and SATA
 - MIPS: octeon: add E1000 ethernet support
 - MIPS: octeon: add Octeon III NIC23 board
 - ata/scsi: add support for Big Endian platforms
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAmCEf04ACgkQKPlOlyTy
 XBj2Aw//SxPX48XynT979cMIOoylO6Rs1saWtQr32YmycWnGC0/wvFNPU/kjNP/a
 jinOxvY2TSBNqToSuCDZxGXyijMIdAnWVCQCUXmah7bZ+GtiYWR0SHNO0TQ+qrBW
 06CC7hgQQqQswGClJe4njwTyVIzTQvyo/UdjS6RWggDZPsnGpyMlR5O56ZCNNH8o
 1XFCG8hSrQBRO38RpXciGS3dFeaqOQy96K9M5pellf9Fh5a+jHyAmK8Z/0R+T6cG
 +PoNh6qZAsXFj0PVuvu0CaXFHpP+fhdA4kEwt64PJCe8D3x7d05COuN0bL+e6D6u
 E4cSnkjmzNgYvoi4YAGaQN9f4PKPSMHuYf7YdIBFCQQ8OtxNXpUHOg0zr4SRnq/C
 ypq285f2O7Aq+3t0BrC7jTjo+Y2PzVIUR8MXpvh698ZSdJnqOlJf0y5tRwdhf/+k
 gh+rT7mWIOoRRWpb6qHMUr5gnparl0gOykspMlQ2NKB+kfmC4RP2pYxQFp82TFIq
 ZMUaXer2/g5dVptEhTU0vBsTrk7s/u239WtwyXpOCdoM6sI/FoMoiCoQoD2isKP6
 mUv/iwTpfNTtQnx5MM2Xsu+8pzcXjaVeoMaNcI55jZ2QTCoMAFA6odYTk+GHS3Vx
 Yt3TLrH6O46PXNSULROkmTR4RgiDHcGCX/HGTKkcA/+X9GDjjNc=
 =JwRN
 -----END PGP SIGNATURE-----

Merge tag 'mips-pull-2021-04-24' of https://source.denx.de/u-boot/custodians/u-boot-mips

- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
2021-04-24 19:39:14 -04:00
Stefan Roese
ec85347102 mips: octeon: Add Octeon III NIC23 board support
This patch adds the basic support for the PCIe target board equipped
with the Octeon III CN2350 SoC.

Signed-off-by: Stefan Roese <sr@denx.de>
2021-04-23 21:22:55 +02:00
Aaron Williams
f9fa8b8948 mips: octeon: octeon_ebb7304: Add board specific QLM init code
This patch adds the board specific QLM/DLM init code to the Octeon 3
EBB7304 board. The configuration of each port is read from the
environment exactly as done in the 2013 U-Boot version to keep the
board and it's configuration compatible.

Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2021-04-23 21:03:25 +02:00
T Karthik Reddy
25484d9070 xilinx: common: Fix boot script address
Currently u-boot supports addresses upto 39-bits only. If anybody
wants to use addresses of more than 39-bits in Linux they will have
a separate memory node in DT. In such cases they will have multiple
memory nodes.
Currently u-boot selects and runs on lower memory bank region.
But bootscript is being loaded on dram bank 0, where dram bank 0 will
point to 1st memory node in DT. If first memory node is mentioned as
higher ddr(>39-bits address) then u-boot cannot load the bootscript.
So fix this issue by setting bootscript address within the lower memory
bank region.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-04-23 08:45:55 +02:00
T Karthik Reddy
82cb49dc00 xilinx: versal: Add usb dfu/thor distro boot support
Change "dfu_usb" to "usb_dfu" for better representation and change
required macros. Add 60s timeout of dfu-utils to start transaction.
Add support for usb thor to distro boot. Remove DFU_ALT_INFO_RAM
as we use bootcmd_usb_dfu instead of dfu_ram.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-04-23 08:45:55 +02:00
T Karthik Reddy
ef1be3e364 xilinx: zynqmp: Add usb dfu/thor distro boot support
In usb boot mode distro boot should select usb device as primary boot
device instead of usb host. So make usb dfu as primary boot device. But do
not list it in boot_targets as fallback option because it is not classic
mode for booting. Using 60s timeout by default should be enough time for
dfu-utils to start transaction. In case none needs this please change
timeout value in the command or disable CONFIG_DFU_TIMEOUT.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-04-23 08:45:55 +02:00
Ashok Reddy Soma
4fb83c9c2b xilinx: versal: Add support for saving env based on bootmode
Enable saving variables to MMC(FAT) and SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).

Enable ENV_FAT_DEVICE_AND_PART="0:auto" for Versal platforms as well.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-04-23 08:43:25 +02:00
Ashok Reddy Soma
cd08513b05 xilinx: zynq: Add support for saving env based on bootmode
Enable saving variables to MMC(FAT), NAND, SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).

Since most of the flashes on zynq evaluation boards are 16MB in size,
set default ENV_OFFSET to 15MB(0xE00000).

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-04-23 08:43:18 +02:00
Peter Robinson
d410dc8802 ARM: imx: udoo_neo: Convert to ethernet DM
Convert the UDOO Neo to ethernet DM support.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2021-04-20 13:31:35 -04:00
Peter Robinson
9db428904f ARM: imx: udoo_neo: convert to DM_MMC
Convert UDOO Neo to use DM MMC.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2021-04-20 13:31:35 -04:00
Denys Drozdov
fd90aca329 toradex: configblock: fix module revision in config block
U-boot might display wrong module revision information
for modules with an assembly version 'K'. "cfgblock create"
does not takes into account all revision digits from PID8.

This fix takes into account all digits of PID8
to store module revision.

Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2021-04-20 07:31:12 -04:00
Andre Przywara
9f4b53436c arm: highbank: Update maintainership
Rob does not have access to any Calxeda systems anymore, also has
expressed a lack of interest in those systems in the past.

I have multiple working Midway nodes under my desk in the office, so
am happy to take over maintainership.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-04-20 07:31:12 -04:00
Andre Przywara
1238d0143a arm: highbank: Do DRAM init from DT
So far U-Boot was hard coding a (surely sufficient) memory size of 512
MB, even though all machines out there have at least 4GB of DRAM.
Since U-Boot uses its memory knowledge to populate the EFI memory map,
we are missing out here, at best losing everything beyond 4GB on Midway
boxes (which typically come with 8GB of DRAM).

Since the management processor populated the DT memory node already with
the detected DRAM size and configuration, we use that to populate
U-Boot's memory bank information, which is the base for the UEFI memory
map.
This finally allows us to get rid of the NR_DRAM_BANKS=0 hack, that we
had in place to avoid U-Boot messing up the DT memory node before
loading the kernel.

Also, to cover the whole of memory, we need to enable PHYS_64BIT.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-04-20 07:31:12 -04:00
Andre Przywara
debb07bf10 net: calxedagmac: Convert to DM_ETH
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.

This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-04-20 07:31:12 -04:00
Andre Przywara
109552d773 arm: highbank: Enable OF_CONTROL
All Calxeda machines are actually a poster book example of device tree
usage: the DT is loaded from flash by the management processor into
DRAM, the memory node is populated with the detected DRAM size and this
DT is then handed over to the kernel.
So it's a shame that U-Boot didn't participate in this chain, but
fortunately this is easy to fix:

Define CONFIG_OF_CONTROL and CONFIG_OF_BOARD, and provide a trivial
function to tell U-Boot about the (fixed) location of the DTB in DRAM.
Then enable DM_SERIAL, to let the PL011 driver pick up the UART platform
data from the DT. Also define AHCI, to bring this driver into the driver
model world as well.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-04-20 07:31:12 -04:00
Camelia Groza
8092e9d0e0 board: freescale: t208xrdb: fdt fixups under DM_ETH
Disable the FMan mEMAC 5 and 6 nodes from the fdt since they are not
available under the supported RCW. Also disable the associated
"fsl,dpa-ethernet" nodes that reference them.

This is a simplified version of the fdt_fixup_fman_ethernet call for
use under DM_ETH.

Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-04-15 14:26:21 +05:30
Michael Walle
9b3843f8f7 board: sl28: add config to enable console output on SER0
Sometimes it is desireable to have the console output on the first
serial line. Introduce a configuration option for it (in the board
scope).

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-04-15 14:22:22 +05:30
Simon Glass
8ff123a685 freescale: ls1021atwr: Drop use of CONFIG_RESET
It is not recommended to use CONFIG_xxx defines for things which are not
Kconfig options. Rename this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-04-15 14:22:17 +05:30
Bin Meng
b3398993ba ppc: qemu: Create a virtual memory mapping of the platform bus
QEMU ppce500 target can dynamically instantiate an eTSEC device on
a platform bus if "-device eTSEC" is given to QEMU. It is presented
as a "simple-bus" in the device tree, with an additional compatible
string "qemu,platform".

Let's create a virtual memory mapping for it in misc_init_r(), in
preparation to adding eTSEC support.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-04-15 14:22:17 +05:30
Aleksandar Gerasimovski
91ee54741e board/km: add support for seli8 design based on nxp ls102x
The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.

It is based on NXP LS1021 SoC and it provides following interfaces:
 - IFC interface for NOR, NAND and external FPGA's
 - 1 x RGMII ETH for debug purposes
 - 2 x SGMII ETH for management communication via back-plane
 - 1 x uQE HDLC for management communication via back-plane
 - 1 x I2C for peripheral devices
 - 1 x SPI for peripheral devices
 - 1 x UART for debug logging

It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.

Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-04-15 14:22:17 +05:30
Asherah Connor
0219279381 qemu: arm: select QFW, MMIO on qemu-arm
Select CMD_QFW and QFW_MMIO in the qemu-arm board (covers arm and
arm64).

Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-04-12 17:45:40 -04:00
Asherah Connor
5b0b43e0e2 x86: qemu: move QFW to its own uclass
We move qfw into its own uclass and split the PIO functions into a
specific driver for that uclass.  The PIO driver is selected in the
qemu-x86 board config (this covers x86 and x86_64).

include/qfw.h is cleaned up and documentation added.

Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2021-04-12 17:44:55 -04:00
Peter Robinson
bedab97a21 Tegra: remove e2220-1170 board
It's an old bringup board with out upstream Linux or L4T support

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2021-04-12 17:17:11 -04:00
Jaehoon Chung
e316aa5858 board: warp: add power_max77696_init() function
Add power_max77696_init() function.
Since warp doesn't support DM, the keeping its code in board file is
better than maintainig the file of driver.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-04-12 14:24:33 -04:00
Tom Rini
d3cfc474b7 ppc: Remove MPC837XEMDS board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 14:33:35 -04:00
Tom Rini
a99dab1d33 ppc: Remove Cyrus_P5020 and P5040 boards
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.  As the P5020 is the last ARCH_P5020 platform, remove that
support as well.

Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-04-10 08:05:07 -04:00
Tom Rini
a84ea228bc ppc: Remove controlcenterd boards
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.

Cc: Mario Six <mario.six@gdsys.cc>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:04:55 -04:00
Tom Rini
7c964c3b93 ppc: Remove gdsys hrcon boards
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline.  Remove them.

Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:04:42 -04:00
Tom Rini
ce4ca2b739 ppc: Remove gdsys strider boards
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline.  Remove them.

Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:04:42 -04:00
Tom Rini
ddfb9aef65 ppc: Remove MPC8308RDB board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:04:42 -04:00
Tom Rini
2322b9568f ppc: Remove T2081QDS board and ARCH_T2081 support
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.  It is also the only ARCH_T2081 board so remove that support
as well.

Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:04:42 -04:00
Tom Rini
4bbcec08eb arm: Remove mx6dlarm2 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:03:55 -04:00
Tom Rini
178d70b5b3 arm: Remove cgtqmx6eval board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:03:55 -04:00
Tom Rini
defd0dcfb9 arm: Remove titanium board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:03:55 -04:00
Tom Rini
80b386abe3 arm: Remove ts4800 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:03:55 -04:00
Tom Rini
4d24862848 arm: Remove mx53evk board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:03:30 -04:00
Tom Rini
397a43dc56 arm: Remove pfla02 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:03:30 -04:00
Tom Rini
a0cacddcaf arm: Remove zc5202 and zc5601 boards
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:03:29 -04:00
Tom Rini
ddfc004009 arm: Remove xpress board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:02:03 -04:00
Tom Rini
b3b0680ec3 arm: Remove kc1 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:24 -04:00
Tom Rini
6d426bb173 arm: Remove am3517_crane board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:24 -04:00
Tom Rini
7db3958f07 arm: Remove omap3_ha board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <linuxfae@technexion.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:24 -04:00
Tom Rini
d137604c20 arm: Remove tricorder board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Thomas Weber <weber@corscience.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:24 -04:00
Tom Rini
96f599009a arm: Remove platinum_picon board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:10 -04:00
Tom Rini
da42646bf4 arm: Remove Broadcom Cygnus boards
These boards have not been converted to CONFIG_DM by the deadline.
Remove them.

Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:09 -04:00
Tom Rini
938c174738 arm: Remove bcm23550_w1d board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:09 -04:00
Tom Rini
0f6807e77b arm: Remove bcm28155_ap board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:09 -04:00
Tom Rini
65a591f639 arm: Remove picosam9g45 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Erik van Luijk <evanluijk@interact.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:09 -04:00
Tom Rini
80c642f16d arm: Remove wb50n board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:09 -04:00
Tom Rini
3cb80c73a8 arm: Remove wb45n board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:09 -04:00
Tom Rini
d59bc09d82 arm: Remove bcm958712k board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:09 -04:00
Tom Rini
9ac8368071 arm: Remove s32v234evb board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:01:00 -04:00
Tom Rini
56124508ce arm: Remove secomx6quq7 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:00:45 -04:00
Tom Rini
c6c26a05b8 arm: Remove vexpress_ca15_tc2 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 08:00:12 -04:00
Tom Rini
4652bef1b6 arm: Remove apf27 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 07:59:35 -04:00
Tom Rini
be3dec48b0 arm: Remove ts4600 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 07:59:35 -04:00
Tom Rini
0fa6bafa89 arm: Remove sc_sps_1 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 07:59:34 -04:00
Tom Rini
b40186fc7e arm: Remove SANSA_FUZE_PLUS board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 07:59:34 -04:00
Tom Rini
539fba2c10 arm: Remove xfi3 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 07:59:30 -04:00
Tom Rini
34af2da9ad ppc: Remove MPC8349ITX board
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI.  The
deadline for this conversion was the v2019.07 release.  The use of CONFIG_AHCI
requires CONFIG_DM.  The deadline for this conversion was v2020.01.  Remove
this board.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 07:58:22 -04:00
Tom Rini
c861d21cba arm: Remove ot1200 board
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI.  The
deadline for this conversion was the v2019.07 release.  In order to
convert to using the DWC SATA driver under DM further migrations are
required.

Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2021-04-10 07:57:42 -04:00
Tom Rini
d8d3b77fc2 arm: Remove dms-ba16 board
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI.  The
deadline for this conversion was the v2019.07 release.  The use of CONFIG_AHCI
requires CONFIG_DM.  The deadline for this conversion was v2020.01.  Remove
this board.

Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10 07:57:29 -04:00
Tom Rini
3f2e3c7845 Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
 Add FIP header support for STM32programmer
 Update uart number when no serial device found for STM32MP1
 Remove board_check_usb_power function when ADC flag is not set
 Update SPL size limitation for STM32MP1
 Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
 -----BEGIN PGP SIGNATURE-----
 
 iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmBwTr0cHHBhdHJpY2Uu
 Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/plSwD/9SAhxTYqAblFZqZmJj
 Lu+F5fwuXXd8S5LwqNeIKULv+UhJngClkE4HdjSl6T0yR10v6YkPNRDVj4+1gzBd
 wZizmCsnqqDW0QGsTO5AVo+oTwhX4RHkvxEF7BjOqtVuoMZGiozE53+29QORHTnZ
 +j8CYAeORf9wvGAi5y+Wr8ICqP6HwPJPNlta4S8iYC867BM38R9evBqynlaZaWPE
 8FhaXwbAj9ZR9ifCiO+7ObgfXGDT63ejCecjE+539m3FWlBrn+/AWLsg4zF037Dw
 DcV324pnVFP4AIOVsuc9hF7luAYctoXQcNHt1QbD3gmWqPQAgpH8Llfq5cMyudza
 /m/112Y7fuLxO3F14DzZSj5l3ims0XG56Yg7zBwN6exDPr3iWA4UwTSH9lRJDnBq
 aJyvLfAFAvz+X15oePjrQrVp7c+6MigeY2nmhVCWV53Yrl+/TnnekQXlHJ3TsHED
 bPW5/LarLge18uACTZvLzYruIvDSU3INPP1W0vUu7YMDwuEp21K1GSspN7yA0yDK
 nrWXxmYJGVWanAEvW//zuuqUhxtNjAb/qIQl0UgjFN9cDT5vJZ7oY3nWOwP+0V2a
 o+qrRxBTWSVliOShYpfjyHRsASRna2QLLUNQaBeoUqZBKNnFvuw4LZzmqNvV+Idj
 +XWRCiSDJnf1zRrMwFLvZZ+UTQ==
 =4VxR
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20210409' of https://source.denx.de/u-boot/custodians/u-boot-stm

Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
2021-04-09 13:10:59 -04:00
Tom Rini
a1e95e3805 u-boot-imx-20210409
-------------------
 
 - Secure Boot :
 	- HAB for MX8M / MX7ULP
 	- CAAM fixes
 - Fixes for imxrt1020
 - Fixes for USDHC driver
 - Fixes for Toradex (Colibri / Apalis)
 - Switch to DM for several boards
 	- mx23 olinuxo
 	- usbarmory
 	- marsboard / riotboard
 	- Gateworks GW Ventana
 - NXP upstream patches (LPDDR / CAAM / HAB)
 
 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7089
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYHA8Xg8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76aVbQCfb0Z+N836ZSAodyLa0t6FSHgKqfYAnRdrWQAv
 MNlGOmmpfHENtE75eSnd
 =g48D
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20210409' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20210409
-------------------

- Secure Boot :
	- HAB for MX8M / MX7ULP
	- CAAM fixes
- Fixes for imxrt1020
- Fixes for USDHC driver
- Fixes for Toradex (Colibri / Apalis)
- Switch to DM for several boards
	- mx23 olinuxo
	- usbarmory
	- marsboard / riotboard
	- Gateworks GW Ventana
- NXP upstream patches (LPDDR / CAAM / HAB)

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7089
2021-04-09 10:08:52 -04:00
Patrick Delaunay
2214d5e54c stm32mp1: remove the board_check_usb_power function when ADC is not activated
Simplify the code of the function board_check_usb_power
based in CONFIG_ADC and adc_measurement; the function is removed by the
linker when the CONFIG_ADC is not activated.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-04-09 11:53:00 +02:00
Jagan Teki
0441b48570 board: stm32: Add Engicam MicroGEA STM32MP1 MicroDev 2.0 7" OF
7" OF is a capacitive touch 7" Open Frame panel solutions with
- 7" AUO B101AW03 LVDS panel
- EDT, FT5526 Touch

MicroGEA STM32MP1 is a STM32MP157A based Micro SoM.

MicroDev 2.0 is a general purpose miniature carrier board with CAN,
LTE and LVDS panel interfaces.

MicroGEA STM32MP1 needs to mount on top of MicroDev 2.0 board with
pluged 7" OF for creating complete MicroGEA STM32MP1 MicroDev 2.0
7" Open Frame Solution board.

Linux dts commit details:

commit <1d278204cbaa> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 7" OF")

Add support for it.

Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2021-04-09 11:53:00 +02:00
Jagan Teki
fd4dc09a4c board: stm32: Add Engicam MicroGEA STM32MP1 MicroDev 2.0 board
MicroDev 2.0 is a general purpose miniature carrier board with CAN,
LTE and LVDS panel interfaces.

Genaral features:
- Ethernet 10/100
- USB Type A
- Audio Out
- microSD
- LVDS panel connector
- Wifi/BT (option)
- UMTS LTE with sim connector (option)

MicroGEA STM32MP1 is a STM32MP157A based Micro SoM.

MicroGEA STM32MP1 needs to mount on top of this MicroDev 2.0 board
for creating complete MicroGEA STM32MP1 MicroDev 2.0 Carrier board.

Linux dts commit details:

commit <f838dae7afd0> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 board")

Add support for it.

Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2021-04-09 11:53:00 +02:00
Jagan Teki
b594ec89fb board: stm32: Add Engicam i.Core STM32MP1 C.TOUCH 2.0
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.

Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector

i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.

i.Core STM32MP1 needs to mount on top of this Carrier board for
creating complete i.Core STM32MP1 C.TOUCH 2.0 board.

Linux dts commit details:

commit <6ca2898df59f> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
C.TOUCH 2.0")

Add support for it.

Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2021-04-09 11:53:00 +02:00
Jagan Teki
30edf40fa8 board: stm32: Add Engicam i.Core STM32MP1 EDIMM2.2 Starter Kit
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.

Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out

i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.

i.Core STM32MP1 needs to mount on top of this Evaluation board for
creating complete i.Core STM32MP1 EDIMM2.2 Starter Kit.

Linux dts commit details:

commit <adc0496104b6> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
EDIMM2.2 Starter Kit")

Add support for it.

Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2021-04-09 11:53:00 +02:00
dillon min
38ac6a1bb3 board: Add rt-thread art-pi board support
All these files are add for support rt-thread art-pi board
- add board/st/stm32h750-art-pi, defconfig, header support for u-boot

for more information about art-pi, please goto:
https://art-pi.gitee.io/website/

Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-04-09 11:53:00 +02:00
Fabio Estevam
c174c0623b pico-imx6ul: Pass the PMIC I2C address in pmic_get()
Pass "pfuze3000@8" in pmic_get() so that the PMIC node can
be found in the devicetree.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-04-08 23:59:50 +02:00
Trevor Woerner
52bbcc340a mx23_olinuxino: convert MMC to driver model
Convert the Olimex Olinuxino board's support for MMC to driver model following
Fabio Estevam's excellent example from:

	commit: 23013aa961:
	mx23evk: Convert to driver model

Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2021-04-08 23:59:50 +02:00
Peter Robinson
dec7755c44 ARM: imx: udoo: convert to DM_ETH
Convert the UDOO board to use DM_ETH.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2021-04-08 20:29:54 +02:00
Peter Robinson
2d0401b118 ARM: imx: udoo: Convert block devices to DM
Enable DM block, DM MMC and DM SATA support on iMX6 Udoo
convert board code to match the DM support.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2021-04-08 20:29:54 +02:00
Peter Robinson
2668e28213 ARM: embestmx6boards: convert mars/riot boards to DM_ETH
Convert the boards to use DM_ETH.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2021-04-08 20:29:54 +02:00
Peter Robinson
c32d240f70 ARM: embestmx6boards: convert the mars/riot boards to DM_MMC
Convert the two Embest boards to use DM MMC.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2021-04-08 20:29:54 +02:00
Giulio Benetti
6bd8845ad4 board: st: stm32f746-disco: fix console is not enabled while init dram
While initializing dram in spl_dram_init(), mdelay() is called that in
order calls get_ticks() that  verifies if timer exists, if doesn't, it
throws a panic(), but since preloader_console_init() has still not been
called those panic()s will fail. This doesn't help debugging, so let's
setup console before calling spl_dram_init() by moving it after
spl_dram_init().

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2021-04-08 20:29:54 +02:00
Giulio Benetti
eeb47ee474 board: freescale: imxrt1050-evk: fix console is not enabled while init dram
While initializing dram in spl_dram_init(), mdelay() is called that in
order calls get_ticks() that  verifies if timer exists, if doesn't, it
throws a panic(), but since preloader_console_init() has still not been
called those panic()s will fail. This doesn't help debugging, so let's
setup console before calling spl_dram_init() by moving it after
spl_dram_init().

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2021-04-08 20:29:53 +02:00
Giulio Benetti
45dae4a3c7 board: freescale: imxrt1020-evk: fix console is not enabled while init dram
While initializing dram in spl_dram_init(), mdelay() is called that in
order calls get_ticks() that  verifies if timer exists, if doesn't, it
throws a panic(), but since preloader_console_init() has still not been
called those panic()s will fail. This doesn't help debugging, so let's
setup console before calling spl_dram_init() by moving it after
spl_dram_init().

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2021-04-08 20:29:53 +02:00
Tim Harvey
bb32c2a617 board: gateworks: venice: fix gsc_get_dev
use dm_i2c_probe instead of i2c_get_chip which appears to be more
reliable.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-04-08 20:29:53 +02:00
Fabio Estevam
aeee33d6e0 MAINTAINERS: Use my personal e-mail address
Use my personal e-mail address for U-Boot related work.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-04-08 20:29:53 +02:00
Tim Harvey
ca3ac1e32a imx: ventana: enable dm for SPI
Enable driver model for SPI which allows us to remove the iomux
and init.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-04-08 20:29:53 +02:00
Tim Harvey
777f333c37 imx: ventana: enable dm for MTD and NAND
Enable driver model for MTD and NAND support allowing us to remove
the iomux, init, and most of the static configuration.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-04-08 20:29:53 +02:00
Tim Harvey
19a387f85d imx: ventana: enable dm support for MMC and SATA
Enable driver model support for MMC and SATA.

Note that DM_MMC requires aliases for your mmc devices so
they are added to the dts. Linux does not support enumerating mmc
devices by alias so these are not present in the Linux dts.

Note that we still need board_mmc_init() and board_mmc_getcd() for
not DM SPL to support MMC.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-04-08 20:29:53 +02:00
Tim Harvey
72c46327f0 imx: ventana: enable dm support for USB
Enable dm support for USB (which also requires dm support for fixed
regulators used for vbus enable) and remove usb iomux which is no
longer needed.

We can remove the handling of otgpwr_en gpio as this is defined in
dt as usbotg vbus-supply but we need to keep the handling of
USB_HUB_RST# for boards that have a USB HUB as that isn't defined in
the dt's currently.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-04-08 20:29:53 +02:00
Tim Harvey
ee025c13b2 imx: ventana: add pinctrl and remove unneeded UART init and config
Once the IMX6 pinctrl driver is added UART is fully using driver mode
so we no longer need to config and initialize it.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-04-08 20:29:53 +02:00
Tim Harvey
d863d05439 imx: ventana: convert U-Boot to OF_CONTROL using FIT image
In preparation for dm conversion convert to OF_CONTROL by adding FIT image
support and multi dtb.

Add a board_fit_config_name_match to match the dtb based off of EEPROM
model.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-04-08 20:29:53 +02:00
Tim Harvey
acb9a13b50 imx: ventana: add Gateworks Ventana dts
Add Gateworks Ventana dts/dtsi files from Linux 5.11 in preparation for
conversion to driver-model.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-04-08 20:29:53 +02:00
Peng Fan
1e4ed2d69d imx8mp-evk: switch to use binman
Use binman to pack images

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 20:29:53 +02:00
Peng Fan
353dfe4b43 imx8mn-ddr4-evk: switch to use binman
Use binman to pack images

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 20:29:53 +02:00
Peng Fan
8996e6b7c6 imx8mm_evk: switch to use binman to pack images
Use binman to pack images

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 20:29:53 +02:00
Tom Rini
f6127db8cc Merge https://source.denx.de/u-boot/custodians/u-boot-riscv
- Watchdog, Unleashed and Icicle improvements
2021-04-08 07:33:14 -04:00
Bin Meng
ae2d9506a3 riscv: sifive: Rename fu540 board to unleashed
In preparation to add SiFive Unmatched board support, let's rename
the existing fu540 board to unleashed.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-04-08 15:37:29 +08:00
Sean Anderson
e3282b1bba riscv: Enable watchdog for the k210
This enables the necessary config options.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-04-08 15:37:28 +08:00
Peng
48ab215741 imx8mn: evk: update MAINTAINERS
Add imx8mn_evk_defconfig to be maintained
Typo fix

Signed-off-by: Peng <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Ye Li
9e05cf0152 imx8mq_evk: Applying default LPDDR4 script for B2
Both i.MX8MQ B1 and B2 should use default LPDDR4 script, while B0
has another dedicated script.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Ye Li
8f9f6ba855 imx8m: ddr: Disable CA VREF Training for LPDDR4
Users reported LPDDR4 MR12 value is set to 0 during PHY training,
not the value from FSP timing structure, which cause compliance test failed.
The root cause is the CATrainOpt[0] is set to 1 in 2D FSP timing
but not set in 1D.  According to PHY training application node,
to enable the feature both 1D and 2D need set this field to 1,
otherwise the training result will be incorrect.
The PHY training doc also recommends to set CATrainOpt[0] to 0 to use
MR12 value from message block (FSP structure). So update the LPDDR4
scripts of all mscale to clear CATrainOpt[0].

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Ye Li
98bcdf1635 imx8mn: Add low drive mode support for DDR4/LPDDR4 EVK
Add dedicated defconfigs for iMX8MN low drive mode which set the VDD_SOC
and VDD_DRAM to 0.8v, DDR at 1600MTS (800Mhz clock) and GPU at 200Mhz.

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Peng Fan
4e805c197b imx8mn: Add LPDDR4 EVK board support
Add support for iMX8MN LPDDR4 EVK board which uses 2GB LPDDR4 and
PCA9450B PMIC.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Peng Fan
e3422b0d59 imx8mn_evk: drop duplicated code
uart clk has been enabled, no need enable again.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Peng Fan
4eeb9fe847 power: pca9450: add a new parameter for power_pca9450_init
Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-04-08 09:18:29 +02:00
Jacky Bai
fd60fe7e61 imx8mn: Update the DDR4 timing script on imx8mn ddr4 evk
On i.MX8MN, we can only support DLL-ON mode only, so update the timing
to support 2400mts & 1066mts setpoint.

Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Peng Fan
41037bc47c imx8mp_evk: Increase VDD_ARM to 0.95v Overdrive voltage
There is a frequency/timing limitation for SOC and ARM, if SOC is OD
voltage/OD freq, then ARM can't run at ND voltage/1.2Ghz, it may have
timing risk from SOC to ARM.

Current VDD_SOC is set to 0.95v OD voltage in SPL, and kernel will
increase bus clocks to OD frequency before it increases ARM voltage.
So to conform to the limitation, we'd better increases VDD_ARM to OD
voltage in SPL.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Peng Fan
2212542f9b imx8mp_evk: spl: clean up including headers
Clean up the including headers

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
haidong.zheng
c994d3d203 imx8mp: refine power on imx8mp board
VDD SOC normal run changed to 0.85V
LPDDR4 freq0 change from 4000MTS to 2400MTS

Signed-off-by: haidong.zheng <haidong.zheng@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Ye Li
d437230954 imx8mp_evk: Update LPDDR4 refresh time
Use more safer refresh time value for 6GB LPDDR4 on this EVK board.
Update the parameters for every frequency point.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Ye Li
c0c78d24bd imx8mp_evk: Update LPDDR4 timing for new FW 202006
After switching to new LPDDR4 firmware 202006 version, have to
update the LPDDR4 timing accordingly from RPA tool.

Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Sherry Sun <sherry.sun@nxp.com>
Tested-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Sherry Sun
31c878f76e imx8mp: ddr: Add inline ECC feature support
Add inline ECC support for lpddr4 on imx8mp-evk. And add a config which
can enable/disable inline ECC feature for lpddr4 on imx8mp-evk board.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Peng Fan
15734d473f imx8mm/p: remove boot.cmd
These files should not be in U-Boot repo

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Ye Li
48ddafd9a4 imx8mm_evk: Switch to new imx8mm evk board
Update PMIC to use PCA9540, the legacy board not supported by NXP

Signed-off-by: Ye Li <ye.li@nxp.com>
2021-04-08 09:18:29 +02:00
Ye Li
cf16dc3329 imx8mm_evk: Update to latest LPDDR4 script
Update LPDDR4 script to sync with v2020.04 u-boot

Signed-off-by: Ye Li <ye.li@nxp.com>
2021-04-08 09:18:29 +02:00
Phil Sutter
a770159f88 arm: mvebu: ds414: Auto-populate env if appropriate
Define a misc_init_r() which calls "syno populate_env" if the
environment seems incomplete (or default), indicated by missing
"ethaddr" variable. With this in place, no random MAC address fallback
is needed anymore.

Signed-off-by: Phil Sutter <phil@nwl.cc>
2021-04-08 08:50:41 +02:00
Phil Sutter
e471ddf0f3 arm: mvebu: board/Synology: Unify legacy kernel support
Move the relevant bits from ds109.{c,h} into common/ and adjust the code
to fit both DS109 and DS414. Moreover:

* Introduce syno_board_id() which translates CONFIG_MACH_TYPE into the
  expected board ID tag value.

* Properly initialize isusbhost, mac and mtu fields from env variables.

* Set the right bootargs/bootcmd to correctly boot legacy kernel out of
  the (DS414) box. Getting the ramdisk location right is a bit tedious.

Cc: Walter Schweizer <swwa@users.sourceforge.net>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-04-08 08:50:17 +02:00
Phil Sutter
08511d129e arm: mvebu: ds414: Add a Kconfig defining some strings
A rather cosmetic change to conform with other board definitions.

Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-04-08 08:50:03 +02:00
Tom Rini
1883652c8e - Add MMIO MDIO mux driver
- Add Amlogic G12A MDIO mux driver
 - Add DM_MDIO support for designware ethernet driver
 - Add Amlogic Meson8b and later designware ethernet glue driver
 - Switch all amlogic boards to Amlogic designware ethernet glue driver
 - Switch all amlogic boards to DM_MDIO when necessary
 - Remove all static ethernet setup code
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmBsLu8ACgkQd9zb2sjI
 SdFj4RAArL8OHCGzyAXrV95fnOnl76koOFnJJ0q6PREwvLWQh3GMpN4CBYtAn95a
 nbakXGN30pHlprrRrYi8nsGHWJX2MW1k8hDWGUJ4f+r2AuvCxMT7h3CHbKY0/pKZ
 h8s7Kwy1ze53ljAbQBUnF3anzYJFPpX3nvjbNo2o5ao0gCUNilEuz1RVn2R72v8R
 kp1iZb0bBhMN3mmNeOs670oXyDoRtX4eWyhbAdrTDhofxTvxfRlQJQrxJ6/I90ex
 IueCsRaT40vl9B5I+JJsanJFDPUTFeZIAc/6DchqPVlXxQjLYP/RjUIxaZbAbnFc
 vyXSWYhoK4GAmgNmXzL00VUVLfKvWvMVMncSgRKRqVY+YBkmoFrP4sYbFrZAPqsB
 yaUoWWnuKurWGRiqbEOlvK+AmQ7So0wWLE/cImmHaadpUDFow3JseeMdZphBdaOp
 4BevvSUNE2k8LazXKyPPlm73Po7uDZmTHYc9ADemBjIj0wvdROvgTdbOdtCAPwnv
 sNVP08l51fskueFYKAkWg1/5hu9YEqzb3C+n9QyZoDNmKaGxQ102HH2gHdXkFqBD
 EciaThsIogUOxYzz7zwU4a44bzzQBuh+yp6C4Ixxe9tOyFyknNppontMUUm41Blk
 HzOvBZjzxqpQOnuVfl1k7xORFXGehCnxwLhZvDIoLYhaqFzgLUc=
 =uQEZ
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20210406' of https://source.denx.de/u-boot/custodians/u-boot-amlogic

- Add MMIO MDIO mux driver
- Add Amlogic G12A MDIO mux driver
- Add DM_MDIO support for designware ethernet driver
- Add Amlogic Meson8b and later designware ethernet glue driver
- Switch all amlogic boards to Amlogic designware ethernet glue driver
- Switch all amlogic boards to DM_MDIO when necessary
- Remove all static ethernet setup code
2021-04-06 08:37:28 -04:00
Neil Armstrong
2fbd37001c arm: meson: remove static ethernet link setup
The static ethernet link type config code is no more needed because now handled by
the meson8b glue driver, delete it.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-04-06 11:10:29 +02:00
Tom Rini
472fd5a35a Merge tag 'rockchip-for-v2021.07' of https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Fix rk3368 lion board support;
- Fix px30 odroid-go2 board support;
- Add rk3399 NanoPi R4s and NanoPi M4B board support;
2021-04-05 22:39:10 -04:00
Tom Rini
db8b46120a Xilinx changes for v2021.07
net:
 - Fix gem PCS support
 
 spi:
 - Small trivial fixes
 
 zynq:
 - Enable time/timer commands
 - Update bitmain platform
 - Several DT changes
 
 zynqmp:
 - Update clock driver
 - mini config alignments
 - Add/update psu_init for zcu208/zcu216/zc1275
 - Several DT changes
 - Enable efi debug command (also for Versal)
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYGRy+AAKCRDKSWXLKUoM
 IUN9AKCQHHdbKIciyhucUj5ThwT3CDaUswCeLQkRB1SrM6E8k6KkErWEA+xOxsU=
 =fIEs
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.07' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2021.07

net:
- Fix gem PCS support

spi:
- Small trivial fixes

zynq:
- Enable time/timer commands
- Update bitmain platform
- Several DT changes

zynqmp:
- Update clock driver
- mini config alignments
- Add/update psu_init for zcu208/zcu216/zc1275
- Several DT changes
- Enable efi debug command (also for Versal)
2021-03-31 09:47:30 -04:00
Michal Simek
cde1aaeae2 arm64: zynqmp: Update psu_init for zcu1275
Update clock/pll setup, ddr, MIOs based on 2020.2 hw design.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Michal Simek
7a50093a44 arm64: zynqmp: Add missing psu inits for zcu208/216
Add missing configurations file for zcu208 and zcu216.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Alexandre Vicenzi
a99d70c180 board: dts: rockchip: Add NanoPi M4B
Add initial support for NanoPi M4B, a minor revision of
the original NanoPi M4.

Commit details of rk3399-nanopi-m4b.dts sync from Linux 5.12-rc4:
"arm64: dts: rockchip: Add NanoPi M4B board"
(sha1: c7b03115003f7f337ab165542cee37148cf30a8a)

Signed-off-by: Alexandre Vicenzi <alexandre.vicenzi@suse.com>
Reviewed-by: Kever Yang <kever.yang@rock-cihps.com>
2021-03-30 16:53:00 +08:00
Xiaobo Tian
b69b9f3f54 arm64: rk3399: Add support NanoPi R4s
NanoPi R4s is SBC base on Rockchip RK3399 hexa-core processor with
dual-Core Cortex-A72 and Mali-T864 GPU with 4GiB(LPDDR4) of RAM, SD card support,
including 2 gigabit ethernet(RTL8211E 1Gbps - RTL8111H 1Gbps) and 2 USB 3.0 port.
port.It also has two GPIO headers which allows further peripherals to be used.

The devicetree file is taken of the rk3399 nanopi4 Linux kernel [1].

[1] e7a0959082

Signed-off-by: xiaobo <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Christoph Muellner
8a5a88308d rockchip: rk3399-puma: Increase environment size to 16 kiB.
On Puma we have the environment at an offset of 16 kiB.
On the eMMC this gives us 16 kiB for the environment before the SPL starts.
On the SPI NOR we also have 16 kiB until end of flash.
So let's increase the environment size from 8 kiB to its maximum
of 16 kiB for both MMC and SPI NOR.

Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Tom Rini
1057b1be75 Prepare v2021.04-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmBiRbMACgkQFHw5/5Y0
 tyz0KAv/T8glQGL6L2CYeLuwbs9tndQoaH2YNb3teNUJrqehBleJAQ6ubHP30d87
 rHrokJ4Zu3TC15sACrK4GOMvsAVkeCuU/jIqFJA4ieDZr8g7yfUMOZMsDiIFdd36
 Rdmi71Jtek/csyS5BfcUUYoXVbUCGQ8yAx7z0VrK0sqsqZYYJNwPmqgkR8U2ulNb
 FiLxwamFwH7+bsvcvHajO1dOyko0zR7GTisf/fOgmlHuF3BldqG4SDcNd528uEWb
 r3fXs2Ut6IaC/beCnmKUPVG3ZjdPtb+T230rRRhUOfjTwqR7SzXp5bTyzdgyw3gU
 rOgfi/mAGQPPG2E2fzPz0JCI1irbnkSE2fVJ4epaVUCoHIEsQQdy034aD3qLcHFY
 65ihEpRvCM7s9jfKX8XeIG4rKFB4i60TX5orzdMvx7wV3rxmPE9qQmF9lkD+fEA+
 TPuFtkjGmluSe+xWBVK7+6xuF6rcLEbNXuFWRi3qMSMgH8rtGfeJRonusOGPolwC
 jQ1T7szW
 =UJ/O
 -----END PGP SIGNATURE-----

Merge tag 'v2021.04-rc5' into next

Prepare v2021.04-rc5
2021-03-29 18:00:21 -04:00
Simon Glass
80a4570c99 x86: coral: Show memory config and SKU ID on startup
Provide the model information through sysinfo so that it shows up on
boot. For memconfig 4 pins are provided, for 16 combinations. For SKU
ID there are two options:

   - two pins provided in a ternary arrangement, for 9 combinations.
   - reading from the EC

Add a binding doc and drop the unused #defines as well.

Example:

   U-Boot 2021.01-rc5

   CPU:   Intel(R) Celeron(R) CPU N3450 @ 1.10GHz
   DRAM:  3.9 GiB
   MMC:   sdmmc@1b,0: 1, emmc@1c,0: 2
   Video: 1024x768x32 @ b0000000
   Model: Google Coral (memconfig 5, SKU 3)

This depends on the GPIO series:

   http://patchwork.ozlabs.org/project/uboot/list/?series=228126

Signed-off-by: Simon Glass <sjg@chromium.org>

Acked-by: Bin Meng <bmeng.cn@gmail.com>
2021-03-27 16:26:48 +13:00
Simon Glass
e35b6497f4 x86: Make coreboot sysinfo available to any x86 board
It is possible to boot U-Boot for chromebook_coral either 'bare metal' or
from coreboot. In the latter case we want to provide access to the coreboot
sysinfo tables. Move the definitions into a file available to any x86
board.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-27 13:59:37 +13:00
Simon Glass
80814f4d0e x86: coral: Free the ACPI GPIOs after using them
These GPIOs are needed later if Chromium OS verified boot is running,
so free them after use.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-27 13:59:36 +13:00
Simon Glass
424994c48f sandbox: Create a new sandbox_noinst build
Move sandbox_spl over to use OF_PLATDATA_INST. Create a new board to
test the case when this is not enabled, since we will be keeping that
code around for several months and want to avoid regressions.

Skip the dm_test_of_plat_dev() test since driver info is not available
for OF_PLATDATA_INST.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-26 17:03:09 +13:00
Chris Packham
b4f8ffb6e8 board: freescale: t208xrdb: Add link to User Guide
The User Guide contains handy things like block diagrams and DIP switch
settings and it's even available on the public web. Add a link to it in
the README.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-23 18:06:07 +05:30
Heinrich Schuchardt
2a38e71265 sandbox: add FAT to the list of usable env drivers
Add the FAT environment driver to the priority list.

When testing the UEFI sub-system the EFI system partition is formatted with
FAT so it is reasonable to store the environment there.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-03-22 19:23:26 +13:00
Fabien Parent
e96bedf146 board: Add MT8183 pumpkin board support
Add the MT8183 pumpkin board support.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
2021-03-20 16:24:27 -04:00
Fabien Parent
4e828d9c75 board: mediatek: mt8516: init USB Ether for pumpkin board
Init USB Ether if CONFIG_USB_ETHER is enabled.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
2021-03-20 16:24:27 -04:00
Fabien Parent
86e07d59ee board: mediatek: rename pumpkin board into mt8516
More than one pumpkin board has been made with different MediaTek SoCs.
Rename the pumpkin board to follow the naming convention of all
other MediaTek boards and also to not be confusing when other pumpkin
boards will be added in follow-up commits.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
2021-03-20 16:24:26 -04:00
Lad Prabhakar
9e346340d7 board: silinux: Enable recovery SPL for EK874 board
Enable building SPL for EK874 board which is based on R8A774C0 SoC.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
2021-03-16 20:09:30 +01:00
Lad Prabhakar
07148c1899 arm: rmobile: Add Silicon Linux EK874 board support
The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).

This patch adds the required board support to boot Si-Linux EK874 board
based on R8A774C0 SoC.

DTS files apart from r8a774c0-ek874-u-boot.dts and r8a774c0-u-boot.dtsi
have been imported from Linux kernel 5.11 commit f40ddce88593
("Linux 5.11").

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
2021-03-16 20:09:29 +01:00
Biju Das
5be85de6a8 arm: rmobile: Add HopeRun HiHope RZ/G2H board support
The HiHope RZ/G2H board from HopeRun consists of main board
(HopeRun HiHope RZ/G2H main board) and sub board(HopeRun
HiHope RZ/G2H sub board). The HiHope RZ/G2H sub board sits
below the HiHope RZ/G2H main board.

This patch adds the required board support to boot HopeRun HiHope
RZ/G2H board.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
2021-03-16 20:09:29 +01:00
Biju Das
dca070c382 arm: rmobile: Add HopeRun HiHope RZ/G2N board support
The HiHope RZ/G2N board from HopeRun consists of main board
(HopeRun HiHope RZ/G2N main board) and sub board(HopeRun
HiHope RZ/G2N sub board). The HiHope RZ/G2N sub board sits
below the HiHope RZ/G2N main board.

This patch adds the required board support to boot HopeRun HiHope
RZ/G2N board.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
2021-03-16 20:09:29 +01:00
Biju Das
b650c83825 arm: rmobile: Add HopeRun HiHope RZ/G2M board support
The HiHope RZ/G2M board from HopeRun consists of main board
(HopeRun HiHope RZ/G2M main board) and sub board(HopeRun
HiHope RZ/G2M sub board). The HiHope RZ/G2M sub board sits
below the HiHope RZ/G2M main board.

This patch adds the required board support to boot HopeRun HiHope
RZ/G2M board.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
2021-03-16 20:09:29 +01:00
Tom Rini
22fc991daf Prepare v2021.04-rc4
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmBPhiUACgkQFHw5/5Y0
 tywChgv/RYpdSKrD5s4kCJnImfOwDznESj/CqAQK3Au5zviq7qXRrgxyTKv2e1wM
 W51vUBd0cE1YTACXqbr92wSSyqoTthLqd57KQgVele5uC2dvkqVTSvjPOUwtyIbQ
 BTPkoQnHPn30AILRdPjpEdBGfZhJDDtJFdQopn6h4GjEjPKVH8Wx1Dd+V6SD5f20
 WiksUjgdjMr1AmORY+LdwwJO8FZrGGPYgs8CDtiqxmCSwh3d7kUFFTT+G23BZdo7
 M+81+1uIUaW2Bolds7ZTPrrjr8bPwkWoTqNYhUB4bNPLp72gwnjM1rtU1X3hyiJM
 MdxSBimLHUOYPihfeSYCHSUrJaQFAAEFkuzWfZN1fgoswKEZQIVVVTzT/TomTyqf
 1DIXD+0HpXGKgVLW/Nkpl4D+UFjR865XI4kiuDxddjKI7bGbvDlbZ/k3PNelD7op
 umUswHnC3OTSw/g+A9VH/zf1rMFNLfu++vD7XJtdoWlcsl6x6/6Fh75tuC6K/X0K
 caPmehD3
 =ENym
 -----END PGP SIGNATURE-----

Merge tag 'v2021.04-rc4' into next

Prepare v2021.04-rc4
2021-03-15 12:15:38 -04:00
Tom Rini
e8a10a02bd - Add WATCHDOG_RESET() in MTD framework and STM32 QSPI driver
- stm32mp1_trusted_defconfig rely on SCMI support
 - Remove the nand MTD configuration for NOR boot in stm32mp1 board
 - STM32programmer update
 - Bsec: manage clock when present in device tree
 - stm32mp15: move bootdelay configuration in defconfig
 - Update for stm32 dsi and dw_mipi_dsi
 - STM32 MCU's cleanup
 - Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
 - Update stm32mp1 doc
 -----BEGIN PGP SIGNATURE-----
 
 iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmBLfA8cHHBhdHJpY2Uu
 Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/pkNnD/4hQrwBdaJMz9YXL4Tp
 0W7kpCcTkG+gINY06BONNnKzBHq62SkWMo/lw9iF0nlcNKSOHzrz6ttm+e54ngs0
 qe/dn0yjgImDfr5p5JRMTG1m7/XwQpucZ8wowSZAwt5f/DDh9eta9AyST0ev+iXI
 Eqgbk5HsF2OCOK6h74FJidZUdLMLw+uQkIwPhglx3ZaxxFfXHAdWtXtJ9Fky2adU
 BC0PltvJ6KYl1LTUGCQvrCST1sNe1PXPHrcsUpsQnqUSZ65tGKgeH2On9Exsw6cE
 eA5v0aiQSMmAH2pYXrJwxhSW9b03yt3NdBQd09Du2YUuFe7yZeoWIFy8mM9jRaov
 QDe88aJ9ZjxB+TvYQPToEL0EIyBGkN3HnX05BtKzKLf+E2+wP6gEf/6Sob7fBf6n
 3n2Eud0COfe06hNiocYOHm8n/8bZxdmuEgMA8LU0PZETbH33NlvJtrjyBxY4OHOV
 G+RG6J8idpVWWQ69g2TqfsVhXSjF893nvLOu0+KjuNrZWG4BVxGjylVUSvayk7bG
 TI++ZKlbdvJGweZ3uUPcNLH4VaX47P/nZS/6vX1uL7NtRNvv3jLHN5z4t6zKI9rh
 3iTJxxVv3zilWcY1WsoSdUvK56RTubnNwUlpjriabdRwMDjMN0isL9N06PvOELoi
 jU1IkKBLtMvPbb2XfLRIjvQjTQ==
 =nIJc
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20210312' of https://source.denx.de/u-boot/custodians/u-boot-stm

- Add WATCHDOG_RESET() in MTD framework and STM32 QSPI driver
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
2021-03-15 08:43:19 -04:00
Patrice Chotard
729fa17f06 board: st: Remove board_early_init_f and board_late_init callbacks for stm32 boards
Remove board_early_init_f() and board_late_init() callbacks for stm32
boards as the corresponding flags (CONFIG_BOARD_LATE_INIT and
CONFIG_BOARD_EARLY_INIT_R) are now disabled.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-03-12 10:57:10 +01:00
Patrick Delaunay
9f97193616 board: stm32mp1: use CONFIG_SYS_MMC_ENV_DEV when available
Check whether user has explicitly defined the mmc device to use
in mmc_get_env_dev() with CONFIG_SYS_MMC_ENV_DEV.

On STMicroelectronics boards the used mmc device for environment is
the instance of boot device provided by the ROM code; the mmc instance
is configured by alias in device tree. The used partition is defined in
device tree with u-boot,mmc-env-partition = "ssbl".

This patch allows to override this selection for the support of customer
boards without alias; for example when SDMMC1 is not used and ENV in
mmc0=SDMMC2, user can force the value: CONFIG_SYS_MMC_ENV_DEV = 0.

On STMicroelectronics boards, the current behavior is kept with
CONFIG_SYS_MMC_ENV_DEV = -1.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-03-11 18:02:51 +01:00
Patrick Delaunay
5a05af87ef stm32mp: stm32prog: Add CONFIG_CMD_STM32PROG_SERIAL and _USB
Add CONFIG_CMD_STM32PROG_SERIAL and CONFIG_CMD_STM32PROG_USB to
independently select the support of UART or USB communication for
STM32CubeProgrammer.

For serial boot over UART, user can deactivate CONFIG_CMD_STM32PROG_SERIAL
to use U-Boot console of binary loaded by UART (for board bring-up for
example).

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-03-11 17:41:17 +01:00
Patrick Delaunay
299ad5d6ba board: st: remove the nand MTD configuration for NOR boot in stm32mp1 board
Since commit d5d726d3cc ("configs: stm32mp1: only support SD card after
NOR in bootcmd_stm32mp"), the stm32mp1 boards only support SD card after
NOR boot device, so the MTD partitions for nand0 or spi-nand0 are useless
(no need of "UBI" partition in nand0 or spi-nand0).

This patch removes these nand MTD update for nor boot and simplify nand0
and spi-nand0 support (remove the mtd_boot variable).

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-03-11 17:40:28 +01:00
Tom Rini
b0a75dda7e Merge branch 'v2021.04-rc4' of https://github.com/lftan/u-boot
- Add VAB support
2021-03-08 07:41:40 -05:00
Bin Meng
1d636a0cd5 ppc: qemu: Move board directory from board/freescale to board/emulation
board/emulation is the place for other QEMU targets like x86, arm,
riscv. Let's move the qemu-ppce500 board codes there.

List me as a co-maintainer for this board.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:44 +05:30
Bin Meng
37c6ceb1b2 ppc: qemu: Drop fixed_sdram()
This function is not called anywhere. Only fsl_ddr_sdram_size() is
necessary [1] for QEMU. Drop it.

[1] arch/powerpc/cpu/mpc85xx/cpu.c::dram_init()

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:44 +05:30
Bin Meng
b516dd5af7 ppc: qemu: Drop a custom env variable 'fdt_addr_r'
Now that we have switched to CONFIG_OF_CONTROL, and we can use the
env variable 'fdtcontroladdr' directly instead of creating one that
is duplicated.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:44 +05:30
Bin Meng
c8f911cb08 ppc: qemu: Delete the temporary FDT virtual-physical mapping after U-Boot is relocated
After U-Boot is relocated to RAM already, the previous temporary FDT
virtual-physical mapping that was used in the pre-relocation phase
is no longer needed. Let's delete the mapping.

get_fdt_virt() might be used before and after relocation, update it
to return different virtual address of FDT.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:44 +05:30
Bin Meng
46c9b59536 ppc: qemu: Enable VirtIO NET support
By default the QEMU ppce500 machine connects a VirtIO NET to the
PCI controller, although it can be replaced to an e1000 NIC via
additional command line options.

Now that we have switched over to DM PCI, VirtIO support becomes
possible. This commit enables the support.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:43 +05:30
Bin Meng
3fc735d4a5 ppc: qemu: Drop CONFIG_OF_BOARD_SETUP
ft_board_setup() is now empty. Drop it.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:43 +05:30
Bin Meng
8ee401670a ppc: qemu: Switch over to use DM ETH and PCI
At present the board supports non-DM version PCI and E1000 drivers.
Switch over to use DM ETH and PCI by:

- Rewrite the PCI address map functions using DM APIs
- Enable CONFIG_MISC_INIT_R to do the PCI initialization and
  address map
- Drop unnecessary ad-hoc config macros
- Remove board_eth_init() in the board codes

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:43 +05:30
Bin Meng
2e91e8b332 ppc: qemu: Switch over to use DM serial
The QEMU ppce500 target integrates 2 NS16550 serial ports. Switch
over to use the DM version of the driver by:

- drop unnecessary ad-hoc config macros
- add get_serial_clock() in the board codes

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:43 +05:30
Bin Meng
c1979d74bc ppc: qemu: Enable OF_CONTROL
The QEMU ppce500 machine generates a device tree blob and passes
it to U-Boot during boot. Let's enable OF_CONTROL with OF_BOARD
and provide board_fdt_blob_setup() in the board codes.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Bin Meng
91617d2865 ppc: qemu: Drop board_early_init_f()
This function does nothing. Drop it.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Bin Meng
49b5cd16eb ppc: qemu: Drop init_laws() and print_laws()
These are no longer needed. Drop them.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Bin Meng
84912a7864 ppc: qemu: Support non-identity PCI bus address
When QEMU originally supported the ppce500 machine back in Jan 2014,
it was created with a 1:1 mapping of PCI bus address. Things seemed
to change rapidly that in Nov 2014 with the following QEMU commits:

commit e6b4e5f4795b ("PPC: e500: Move CCSR and MMIO space to upper end of address space")

and

commit cb3778a0455a ("PPC: e500 pci host: Add support for ATMUs")

the PCI memory and IO physical address were moved to beyond 4 GiB,
but PCI bus address remained below 4 GiB, hence a non-identity
mapping was created. Unfortunately corresponding U-Boot updates
were missed along with the QEMU changes and the U-Boot QEMU ppce500
PCI support has been broken since then.

This commit makes the PCI (non-DM version) work again.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Bin Meng
5cd1ecb994 ppc: qemu: Update MAINTAINERS for correct email address
Alex's previous email address is no longer reachable.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
6ce33e2288 board: ls1012aqds: Update MAINTAINERS
Update LS1012AQDS Board MAINTAINERS entries to
current MAINTAINERS.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
044732a903 board: lx2160a: Update MAINTAINERS
Update LX2160AQDS BOARD MAINTAINER entry to
current MAINTAINER.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
088fad9941 board: ls1046ardb: Update MAINTAINERS
Update LS1046ARDB BOARD MAINTAINERS entries to
current MAINTAINERS.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
b0289d9951 board: ls1046aqds: Update MAINTAINERS
Update LS1046AQDS BOARD MAINTAINERS entries to
current MAINTAINERS.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
f94911ed8f board: ls2080ardb: Update MAINTAINERS
Update LS2080ARDB BOARD MAINTAINERS entries to
current MAINTAINERS.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
033743d7ed board: ls2080aqds: Update MAINTAINERS
Update LS2080AQDS BOARD MAINTAINERS entries to
current MAINTAINERS.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
8f75c959e9 board: ls1088a: Update MAINTAINERS
Update LS1088ARDB, LS1088AQDS BOARD MAINTAINERS
entries to current MAINTAINERS.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
b4d5d84484 board: ls1043ardb: Update MAINTAINERS
Update LS1043ARDB BOARD MAINTAINERS entries
to current MAINTAINERS.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
9a558e3c28 board: ls1028a: Update MAINTAINERS
Update LS1028AQDS, LS10128ARDB board MAINTAINERS
entries to current MAINTAINERS.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
1729147c5a board: ls1021atwr: Update MAINTAINERS
Update LS1021ATWR BOARD MAINTAINERS entries to
current MAINTAINERS.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
2e4dbeffab board: ls1021aiot: Update MAINTAINERS
Update LS1021AIOT BOARD MAINTAINERS entries to
current MAINTAINERS.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:42 +05:30
Priyanka Jain
caa18f046f board: ls1012ardb: Update MAINTAINERS
Update LS1012ARDB BOARD MAINTAINERS entries
to current MAINTAINERS.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:41 +05:30
Priyanka Jain
c245727d31 board: ls1012afrdm: Update MAINTAINERS
Update LS1012AFRWY BOARD MAINTAINER entry
to current MAINTAINER.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:41 +05:30
Priyanka Jain
ebc0730bc7 board: corenet_ds: MAINTAINERS: Remove redundant entries
Remove MAINTAINERS entries for
P3041DS_NAND_SECURE_BOOT_defconfig
and P5040DS_NAND_SECURE_BOOT_defconfig
as these configs support have been removed.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:41 +05:30
Stephen Carlson
b5ee48c099 arm: fsl: common: Improve NXP VID driver PMBus support
This patch adds support for more PMBus compatible devices to the NXP
drivers for its QorIQ family devices. At runtime, the voltage regulator is
queried over I2C, and the required voltage multiplier determined. This
change supports the DIRECT and LINEAR PMBus voltage reporting modes.

Previously, the driver only supported a few specific devices such as the
IR36021 and LTC3882, so this change allows the QorIQ series to be used
with a much larger variety of core voltage regulator devices.

checkpatch warning "Use if (IS_DEFINED (...))" was ignored to maintain
consistency with the existing code.

Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-03-05 10:25:41 +05:30
Tom Rini
52ba373b78 i.MX for 2021.04
----------------
 
 - new boards:
 	- i.MX8MN Beacon EmbeddedWorks (2GB)
 	- Gateworks Venice imx8mm
 - convert to DM:
 	- imx53-qsb, mx53loco, mx51evk, mx23-evk
 - Fixes :
 	- Network : FEC ethernet quirks
 	- DH dh-imx6
 
 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/6597
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYD+asg8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76YI0QCeLhbpWfZM7sixvsEsLNt6DLvEiEQAnRqSjFsQ
 BEcRslPhjQc+mALAHDYD
 =7fLb
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20210303' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

i.MX for 2021.04
----------------

- new boards:
	- i.MX8MN Beacon EmbeddedWorks (2GB)
	- Gateworks Venice imx8mm
- convert to DM:
	- imx53-qsb, mx53loco, mx51evk, mx23-evk
- Fixes :
	- Network : FEC ethernet quirks
	- DH dh-imx6

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/6597
2021-03-03 10:10:34 -05:00
Tim Harvey
03bf8436a3 board: gateworks: imx8mm: Add Gateworks Venice board support
Add initial support for Gateworks Venice product family based on the
i.MX 8M Mini SoC

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-03-03 14:15:02 +01:00
Pali Rohár
69b78cbf5e Nokia RX-51: Move content of rx51.h to rx51.c
After removal of MUX configuration there is no need to have extra rx51.h.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
2021-03-03 04:12:46 +01:00
Pali Rohár
b99e03d90b Nokia RX-51: Remove function set_muxconf_regs()
This function is not used and was never called.

This board contains '#define CONFIG_SKIP_LOWLEVEL_INIT' because X-Loader
set everything up, including MUX configuration.

Also this MUX configuration is incorrect and does not match hardware.

So remove this dead, unused and broken code.

This change will decrease size of U-Boot binary.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
2021-03-03 04:12:46 +01:00
Simon Glass
d6a885f087 tpm: Switch TPMv1 over to use the new API
Take over the plain 'tpm_...' functions for use by the new TPM API. Rename
all the TPMv1 functions so they are called from the API.

Update the TPMv1 functions so that they are called from the API. Change
existing users to use the tpm1_ prefix so they don't need to go through
the API, which might introduce uncertainty.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
2021-03-02 15:53:37 -05:00
Harald Seiler
35b65dd8ef reset: Remove addr parameter from reset_cpu()
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to.  This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value.  Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.

Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g.  COLD vs WARM resets).  As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).

To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely.  Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.

This transformation was done with the following coccinelle patch:

    @@
    expression argvalue;
    @@
    - reset_cpu(argvalue)
    + reset_cpu()

    @@
    identifier argname;
    type argtype;
    @@
    - reset_cpu(argtype argname)
    + reset_cpu(void)
    { ... }

Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-03-02 14:03:02 -05:00
Harald Seiler
10b86ef9b3 board: ns3: Remove superfluous reset logic
The current implementation of reset_cpu() in the ns3 board code does not
archieve what it is supposed to (according to the comments), due to
a number of reasons:

 1. The argument to reset_cpu() is _not_ actually passed from the
    `reset` command, but is set to 0 in all call-sites (in this
    specific case, see arch/arm/lib/reset.c).  Thus, performing
    different kinds of resets based on its value will not work as
    expected.

 2. Contrary to its documentation, the passed argument is not
    interpreted, but a static `L3_RESET` define is used.  The other
    comment properly notes that this will always perform a L3 reset,
    though.

 3. The "parsing" of the static `L3_RESET` value is not even using the
    upper and lower nibble as stated in the comment, but uses the last
    two decimal digits of the value.

This is currently one of the only implementations left in U-Boot, which
make "use" of the value passed to reset_cpu().  As this is done under
false assumption (the value does not have any meaning anymore), it makes
sense to bring it into line with the rest and start ignoring the
parameter.

This is a preparation for removal of the reset_cpu() parameter across
the entire tree in a later patch.

Fixes: b5a152e7ca ("board: ns3: default reset type to L3")
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-03-02 11:24:29 -05:00
Adam Ford
5d9b166401 imx: Add 2GB lpddr support for i.MX8MN Beacon EmbeddedWorks devkit.
There is a second lpddr configuration with 2GB of RAM, but this requires
different RAM timings, so in addition to adding the timing file, a
separate defconfig is necessary.

Signed-off-by: Adam Ford <aford173@gmail.com>
2021-03-01 10:21:36 +01:00
Fabio Estevam
b03df2d1c6 mx23evk: Add myself as maintainer
I would like to help supporting this board, so add myself
as a maintainer.

Now that the board has been converted to DM, also add
its devicetree in the MAINTAINERS files entry.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01 10:21:36 +01:00
Fabio Estevam
23013aa961 mx23evk: Convert to driver model
Make the conversion to driver model as it is mandatory.

Successfully tested booting Linux from the SD card.

Dropped splash screen support as this needs to be properly
converted to DM and tested.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01 10:21:36 +01:00
Fabio Estevam
a2eb1be1a5 mx51evk: Add myself as maintainer
I would like to help supporting this board, so add myself
as a maintainer.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01 10:21:36 +01:00
Fabio Estevam
07fc671d7e mx51evk: Convert to driver model
Make the conversion to driver model as it is mandatory.

Tested booting the Linux kernel from the SD card.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01 10:21:36 +01:00
Fabio Estevam
9a68a2be8e mx53loco: Add myself as maintainer
I would like to help supporting this board, so add myself
as a maintainer.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01 10:21:36 +01:00
Fabio Estevam
5c8db4922d mx53loco: Convert to driver model
Make the conversion to driver model as it is mandatory.

Remove the SATA support for now as the i.MX53 support has not
been added yet.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01 10:21:36 +01:00
Heinrich Schuchardt
a3bbd0b912 Correct U-Boot upstream repository
The U-Boot source moves to https://source.denx.de/u-boot/u-boot.git
effective 2021-02-28.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-02-28 13:57:30 -05:00
Tom Rini
99bebbd5b2 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- turris_mox: Enhancements, mostlly defconfig changes (Pali)
- pci-aardvark: Set Max Payload Size and Max Read Request Size
                to 512 bytes (Pali)
- pci_mvebu: Minor cleanup and refactoring (Marek)
- Upgrade A38x DDR3 training to version 14.0.0 (Marek)
2021-02-26 07:55:16 -05:00
Tom Rini
d9bc92f554 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-samsung 2021-02-26 07:54:27 -05:00
Moti Buskila
32e7a6baef ddr: marvell: a38x: add support for twin-die combined memory device
commit 6285efb8a118940877522c4c07bd7c64569b4f5f upstream.

the twin-die combined memory device should be treatened as X8
device and not as X16 one

Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
[ - the default value for twin_die_combined is set to NOT_COMBINED for
    all boards, as this was default behaviour prior this change ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
2021-02-26 10:22:29 +01:00
Tom Rini
2cc6071ed4 ppc: Remove MPC8569MDS board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.  As this is the last ARCH_MPC8569 board, remove that support
as well.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-25 11:59:54 -05:00
Tom Rini
93ef93b60b arm: Remove sksimx6 board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2021-02-25 11:59:53 -05:00
Tom Rini
53ad2db946 arm: Remove mx53smd board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-02-25 11:59:06 -05:00
Tom Rini
1c4bd238b5 arm: Remove mx53ard board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-02-25 11:59:05 -05:00
Tom Rini
2610bf14b5 arm: Remove mx25pdk board
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-02-25 11:59:05 -05:00
Tom Rini
cbe607b920 Xilinx changes for v2021.04-rc3
qspi:
 - Support for dual/quad mode
 - Fix speed handling
 
 clk:
 - Add clock enable function for zynq/zynqmp/versal
 
 gem:
 - Enable clock for Versal
 - Fix error path
 - Fix mdio deregistration path
 
 fpga:
 - Fix buffer alignment for ZynqMP
 
 xilinx:
 - Fix reset reason clearing in ZynqMP
 - Show silicon version in SPL for Zynq/ZynqMP
 - Fix DTB selection for ZynqMP
 - Rename zc1275 to zcu1275 to match DT name
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYDUezQAKCRDKSWXLKUoM
 IbtgAJ9jZ+BOtwFaHR19TENC2DsHTINnnwCfSDn3fU0OFJRI0HD7pRxXr4xrb3M=
 =Kr8x
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx changes for v2021.04-rc3

qspi:
- Support for dual/quad mode
- Fix speed handling

clk:
- Add clock enable function for zynq/zynqmp/versal

gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path

fpga:
- Fix buffer alignment for ZynqMP

xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
2021-02-23 10:45:55 -05:00
Michal Simek
3600d47b73 arm64: zynqmp: Rename zc1275/zcu1275 to be aligned with DT name
Folder names corresponds to DT name. These boards have been renamed from
zc1275 to zcu1275 by commit shown below and this should be the part of that
commit.

Fixes: 420d446781 ("arm64: zynqmp: Rename zc1275 to zcu1275")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-02-23 14:56:59 +01:00
Michal Simek
3aba25bc38 arm64: zynqmp: Do not clear reset reason
There is no need to clear reset reason register because it is protected by
PMUFW already which is reported when verbose log is enabled as:
pm_core.c@733 APU> No write permission to 0xFF5E0220

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-02-23 14:56:59 +01:00
Minkyu Kang
0b547b40b1 samsung: origen: change maintainer
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2021-02-23 15:43:27 +09:00
Minkyu Kang
2881d748ea samsung: espresso7420: change maintainer
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2021-02-23 15:43:27 +09:00
Minkyu Kang
8bed6cc89a samsung: smdkv310: change maintainer
change maintainer to Jaehoon

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-23 15:43:27 +09:00
Minkyu Kang
fec41dc8e9 samsung: smdk5420: change maintainer
change maintainer to Jaehoon

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-23 15:43:27 +09:00
Minkyu Kang
509b62725e samsung: smdk5250: change maintainer
change maintainer to Jaehoon

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-23 15:43:27 +09:00
Minkyu Kang
d42ad5e355 samsung: goni: change maintainer
change maintainer to Jaehoon

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-23 15:43:27 +09:00
Jaehoon Chung
579d819971 board: samsung: covert to driver model about power_key_pressed
Convert to driver model about power_key_pressed.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2021-02-23 15:43:13 +09:00
Tom Rini
a3ddc776fa - splash_source warning fix when building with 64-bit toolchains
- lq123p1jx31 and nv101wxmn51 compatible in simple panel driver
  - remove not used mb862xx driver
  - add Himax HX8238D panel driver
  - s/video_uc_platdata/video_uc_plat/
 -----BEGIN PGP SIGNATURE-----
 
 iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYDOevA4cYWd1c3RAZGVu
 eC5kZQAKCRBM6ATMmsalXNaAAJ0RUysoiZFAddxyrW7otwe+xxmdTACbBcVXCPuX
 W41gJtQyftU4rMGbMoo=
 =iAX1
 -----END PGP SIGNATURE-----

Merge tag 'video-for-v2021.04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-video

 - splash_source warning fix when building with 64-bit toolchains
 - lq123p1jx31 and nv101wxmn51 compatible in simple panel driver
 - remove not used mb862xx driver
 - add Himax HX8238D panel driver
 - s/video_uc_platdata/video_uc_plat/
2021-02-22 09:11:27 -05:00
Sinan Akman
a2c48cb757 mpc8379erdb: Convert to DM_MMC
Signed-off-by: Sinan Akman <sinan@writeme.com>
2021-02-21 18:46:41 -05:00
Igor Opaniuk
2147a16983 dm: i2c: use CONFIG_IS_ENABLED macro for DM_I2C/DM_I2C_GPIO
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.

CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.

All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
     's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
    's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
    's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +

Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-21 06:08:00 +01:00
Heinrich Schuchardt
3e831bfed4 video: remove unused include/mb862xx.h
CONFIG_VIDEO_MB862xx cannot be selected by any configuration.
So we can eliminate include/mb862xx.h.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-19 22:36:56 +01:00
Nicolas Saenz Julienne
561bce3522 rpi: Add identifier for the new CM4
The Raspberry Pi Foundation released the new Compute Module 4 which we
want to detect, so we can enable Ethernet on it and know the correct
device tree file name.

Note that this sets the Ethernet option to true since the official CM4
IO board has an Ethernet port. But that might not be the case when using
custom ones.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2021-02-18 11:56:25 +01:00
Nicolas Saenz Julienne
f10f536281 rpi: Add identifier for the new RPi400
The Raspberry Pi Foundation released the new RPi400 which we want to
detect, so we can enable Ethernet on it and know the correct device tree
file name.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2021-02-18 11:56:25 +01:00
Marek Szyprowski
6b3d18c2cb rpi: limit size of the RAM to the multiple of the MMU_SECTION_SIZE
When RPi4 is booted from USB Mass Storage, the firmware reports 947MiB of
the ARM memory (948 in case of the standard SD-card boot). This value is
not MMU_SECTION_SIZE aligned, so the dram_bank_mmu_setup() skips mapping
of the last 1MiB. This later causes u-boot in ARM 32bit mode to freeze,
because it relocated itself into that unmapped memory and fails to
execute.

Fix this by limiting the size of the first bank to the multiple of
MMU_SECTION_SIZE.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2021-02-18 11:56:25 +01:00
Tom Rini
2ae80437fb Merge branch '2021-02-02-drop-asm_global_data-when-unused'
- Merge the patch to take <asm/global_data.h> out of <common.h>
2021-02-15 10:16:45 -05:00
Tom Rini
73effc2dca sh: Remove sh7763rdp board
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well.  Remove it.

Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-15 10:16:24 -05:00
Tom Rini
f0debb2136 sh: Remove sh7757lcr board
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well.  Remove it.

As this is the last SH4A board, remove that support as well.

Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-15 10:16:24 -05:00
Tom Rini
0c3cd2443b sh: Remove sh7753evb board
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well.  Remove it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-15 10:16:24 -05:00
Tom Rini
da43d96f03 sh: Remove sh7752evb board
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well.  Remove it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-15 10:16:23 -05:00
Tom Rini
215386e48c sh: Remove r7780mp board
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well.  Remove it.

Patch-cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Patch-cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-15 10:16:23 -05:00
Tom Rini
5617351532 sh: Remove MigoR board
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well.  Remove it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-15 10:16:23 -05:00
Tom Rini
865acad78f ppc: Remove MPC8641HPCN board
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI.  The
deadline for this conversion was the v2019.07 release.  The use of CONFIG_AHCI
requires CONFIG_DM.  The deadline for this conversion was v2020.01.  Remove
this board.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-15 10:16:21 -05:00
Tom Rini
41bacbe142 ppc: Remove MPC8610HPCD board
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI.  The
deadline for this conversion was the v2019.07 release.  The use of CONFIG_AHCI
requires CONFIG_DM.  The deadline for this conversion was v2020.01.  Remove
this board.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-15 10:15:48 -05:00
Tom Rini
2dce449801 ppc: Remove MPC8572DS board
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI.  The
deadline for this conversion was the v2019.07 release.  The use of CONFIG_AHCI
requires CONFIG_DM.  The deadline for this conversion was v2020.01.  Remove
this board.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-15 10:15:13 -05:00
Tom Rini
23397775bc ppc: Remove MPC8544DS board
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI.  The
deadline for this conversion was the v2019.07 release.  The use of CONFIG_AHCI
requires CONFIG_DM.  The deadline for this conversion was v2020.01.  Remove
this board.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-15 10:14:03 -05:00
Tom Rini
22924317be arm: Remove db-88f6281-bp board
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago.  In addition there are other DM
migrations it is also missing.  Remove it.

Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Chris Packham <judge.packham@gmail.com>
2021-02-15 10:11:38 -05:00
Tom Rini
2ce7b65d6d arm: Remove ls2080a_simu board
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago.  In addition there are other DM
migrations it is also missing.  Remove it.

Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-15 10:11:38 -05:00
Tom Rini
a1361f4581 arm: Remove mx35pdk board
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago.  In addition there are other DM
migrations it is also missing.  Remove it.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2021-02-15 10:11:38 -05:00
Tom Rini
8444860ca0 arm: Remove apx4devkit board
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago.  In addition there are other DM
migrations it is also missing.  Remove it.

Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lauri Hintsala <lauri.hintsala@silabs.com<mailto:lauri.hintsala@silabs.com>>
Signed-off-by: Tom Rini <trini@konsulko.com<mailto:trini@konsulko.com>>
2021-02-15 10:11:37 -05:00
Michal Simek
98757d87ee xilinx: Show silicon version in SPL
Both Zynq and ZynqMP can show silicon versions in SPL boot flow. It is
useful to be aware.
The patch is also fixing possition of these bits on ZynqMP.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-02-10 13:21:12 +01:00
Michal Simek
fc3c6fd752 xilinx: common: Fix CONFIG_XILINX_OF_BOARD_DTB_ADDR handling for ZynqMP
Fix bug introduced by commit listed below. It is for cases where Versal or
ZynqMP don't have DDR mapped. Later SPL was also excluded by
commit a672b9871b ("xilinx: common: Do not touch
CONFIG_XILINX_OF_BOARD_DTB_ADDR in SPL").

Fixes: 506009fc10 ("xilinx: common: Change macro handling in board_fdt_blob_setup()")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-02-10 13:20:27 +01:00
Marek Szyprowski
8bc780106c board: amlogic: odroid: add runtime detection of the N2/N2+/C4/HC4 variants
Use the ADC channel 1 to check the hardware revision of the board and
detect the N2 vs. N2+ and the C4 vs. HC4 variants. Each of them use
different dtb file, so adjust fdtfile environment variable to the
detected variant.

The ADC min/max values for each variant are taken from the vendor code,
adjusted to the 12-bit ADC driver operation mode (vendor code use 10-bit
mode).

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-02-10 10:00:51 +01:00
Tom Rini
e14d5762de Merge git://git.denx.de/u-boot-marvell
- Espressobin: Set default env values at runtime (Pali)
- Espressobin: Set the maximum slave SPI speed to 40MHz (Pali)
- theadorable: PCIe test code enhancement and early deemphasis
  enabling (Stefan)
- pci_mvebu: Disable config access to PCI host bridge ports (Stefan)
- mv_sdhci: parse device-tree entry (Baruch)
2021-02-08 10:55:51 -05:00
Tom Rini
a10d06add7 Merge git://git.denx.de/u-boot-fsl-qoriq
Layerscape: Enable gpio
Bug fixes & updates related to dspi, qspi, pciep, SVR mask,
stream-id, env variables, mdio for LAyerscape Platforms
Add SATA, network variant 1, 2 support on sl28
powerpc: T1042: drop CONFIG_VIDEO, Add kmcent2 board supporrt, keymile
Bug fixes and updates for keymile, Kontron
2021-02-08 10:55:28 -05:00
Aleksandar Gerasimovski
a1f57c3933 board/km: move km i2c deblock declarations to a km/common.h
Cleanup, move the declarations to keymile/common.h instead declaring them
per-board config.h

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:18 +05:30
Niel Fourie
37bfd9cb50 PowerPC: keymile: Add support for kmcent2 board
Add basic support for the Hitachi Power Grids kmcent2 board, based
on the NXP QorIQ T1040 SoC.

Signed-off-by: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[Fixed blank line at EOF errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:18 +05:30
Niel Fourie
df86d324c7 keymile: common: update to set_env_hex(), fix "pram" radix
Replace instances of sprintf()/set_env() for setting hexadecimal
values with set_env_hex().

In set_km_env() the "pram" variable was set to an hexadecimal
value, while initr_mem() expects an unsigned decimal, so use
set_env_ulong() instead.

Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:17 +05:30
Aleksandar Gerasimovski
e081d9441e board/km/common: fix pnvramaddr and varaddr
Take into account SDRAM_BASE address when calculating pnvramaddr and
varaddr offsets.
Up to now Keymile designs had SDRAM_BASE equal to zero and the offsets
where calculated correctly, this fix is for the upcoming designs that
have SDRAM_BASE different then zero.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:17 +05:30
Aleksandar Gerasimovski
d141f4b298 keymile: common: qrio: print QRIO id and revision number
Add show_qrio function to print chip id and revision information.
There are already multiple QRIO chip versions available and the upcoming
designs may want to show used version.

Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:17 +05:30
Aleksandar Gerasimovski
b99cc27111 board: keymile: common: fix qrio compilation for arm
This patch is fixing qrio driver compilation for ARM architecture:
- It includes asm/io.h for in_/out_ access
- It use correct names for set/clear_bits as defined in linux/bitops.h

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:16 +05:30
Michael Walle
805b2423b4 board: sl28: add SATA support
Enable SATA support. Although not supported by the usual SATA pins on
the SMARC baseboard connector, SATA mode is supported on a PCIe lane.
This way one can use a mSATA card in a Mini PCI slot.

We need to invert the received data because in this mode the polarity of
the SerDes lane is swapped. Provide a fixup in board_early_init_f() for
the SPL. board_early_init_f() is then not common between SPL and u-boot
proper anymore, thus common.c is removed, as it just contained said
function.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:16 +05:30
Michael Walle
b463010be0 board: sl28: add network variant 2 support
Although this variant has two external network ports, they are not (yet)
supported by the bootloader because they are connected via an internal
network switch. Otherwise its the same as the other variants.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:16 +05:30
Michael Walle
4029d356e6 board: sl28: add network variant 1 support
This variant has one network port connected via RGMII and doesn't have
any TSN capabilities out-of-the-box. Instead it has all four SerDes
lanes available for customer use.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:15 +05:30
Stefan Roese
61b70422c3 arm: mvebu: theadorable: Set deephasis bit in PCIe configs very early
Testing has shown, that the quality of the PCIe signals and also the
stability of correct link establishment on the 2 PCIe ports is better,
when the deemphasis bit is set in the PCIe config register.

This needs to be done very early, even before the SERDES setup code is
run. This way, the first link will already be established with this
setup.

Signed-off-by: Stefan Roese <sr@denx.de>
2021-02-08 08:53:14 +01:00
Stefan Roese
54504de24d arm: mvebu: theadorable: Enhance "pcie" test cmd to check link width/speed
This patch changes the board specific "pcie" U-Boot command to not only
check for PCIe device existance but also for the correct link speed
and width that has been established. This cmd can be used by U-Boot
scripts for automated testing, if the PCIe setup is correct. Meaning,
that all PCIe devices are correctly detected and the link speed and
width is corrent.

Signed-off-by: Stefan Roese <sr@denx.de>
2021-02-08 08:53:14 +01:00
Pali Rohár
44be835d25 arm: mvebu: Espressobin: Set default value for $ethNaddr env variable
On Espressobin board are MAC addresses stored in U-Boot env area. Therefore
they are not present in default_environment[] array constructed at compile
time.

This change puts permanent MAC addresses into default_environment[] array
at board runtime. Espressobin board has enabled DEFAULT_ENV_IS_RW option
and therefore can modify this array.

This change ensure that 'env default -a' does not delete permanent MAC
addresses from Espressobin env storage area.

Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
2021-02-08 08:53:08 +01:00
Pali Rohár
c4df0f6f31 arm: mvebu: Espressobin: Set default value for $fdtfile env variable
On Espressobin board value for $fdtfile cannot be determined at compile
time and is calculated at board runtime code. This change uses a new option
DEFAULT_ENV_IS_RW to allow modifying default_environment[] array at runtime
and set into it correct value.

This change also ensure that 'env default -a' set correct value to $fdtfile.

Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
2021-02-08 08:53:08 +01:00
Adam Ford
0099dfd5e5 ARM: rmobile: Add Beacon EmbeddedWorks RZG2H Dev Kit
The Beacon EmbeddedWorks kit is based on the R8A774E1 SoC also
known as the RZ/G2H.

The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.  It shares much of the same design as
the RZ/G2M and RZ/G2N dev kits.

Signed-off-by: Adam Ford <aford173@gmail.com>
2021-02-07 21:12:57 +01:00
Adam Ford
6001b49920 ARM: rmobile: Add Beacon EmbeddedWorks RZG2N Dev Kit
The Beacon EmbeddedWorks kit is based on the R8A774B1 SoC also
known as the RZ/G2N.

The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.  It shares much of the same design as
the RZ/G2M dev kit.

Signed-off-by: Adam Ford <aford173@gmail.com>
2021-02-07 21:12:57 +01:00
Simon Glass
2764cf5e97 x86: coral: Add sysinfo ops
These ops are missing at present which is not permitted. Add an empty
operation struct.

Note: If the uclass requires operations then the drivers should provide
them. Otherwise, checking for missing operations must be done in every
uclass operation, so it adds to code size.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-02-06 19:20:34 +08:00
Tom Rini
8308a28af8 Merge tag 'ti-v2021.04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
2021-02-05 09:39:31 -05:00
David Lechner
f4e2c10a71 ARM: legoev3: drop bi_arch_number
This drops assigning bi_arch_number on LEGO MINDSTORMS EV3. This board
never had its own unique number and since we are using device tree,
we no longer need to pass an arch number to Linux.

Signed-off-by: David Lechner <david@lechnology.com>
2021-02-04 20:37:56 +05:30
David Lechner
68432b5d12 ARM: legoev3: set serial# env var
This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.

Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).

Signed-off-by: David Lechner <david@lechnology.com>
2021-02-04 20:37:56 +05:30
Pali Rohár
64fd2d2614 Nokia RX-51: Convert to CONFIG_DM_MMC
Move twl4030_power_mmc_init() from board_mmc_power_init() to misc_init_r()
and disable CONFIG_SYS_MALLOC_F. Otherwise U-Boot cannot initialize MMC.
Also disable CONFIG_CMD_SLEEP CONFIG_DM_DEVICE_REMOVE CONFIG_MMC_VERBOSE to
free some space.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2021-02-04 20:37:56 +05:30
Bin Meng
b7324b5d53 riscv: ax25-ae350: Cast addr with uintptr_t
addr was delcared as fdt_addr_t which is now a 64-bit address.
In a 32-bit build, this causes the following warning seen when
building ax25-ae350.c:

  warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]

Cast addr with uintptr_t.

Signed-off-by: Bin Meng <bin.meng@windriver.com>
2021-02-03 03:38:41 -07:00
Simon Glass
401d1c4f5d common: Drop asm/global_data.h from common header
Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-02 15:33:42 -05:00
Pali Rohár
9d716339fb arm: mvebu: Espressobin: Disable slot when emmc is not present
This change extends previous commit 061c6d1b23 ("arm: mvebu: Espressobin:
Detect presence of emmc at runtime") and when emmc is not present then emmc
is removed from U-Boot DM and corresponding slot is disabled. Therefore on
Espressobin board without soldered emmc, state of emmc hw should be same as
if emmc was disabled in DTS.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-01-27 07:29:43 +01:00
Dennis Gilmore
9c690314db ARM: mvebu: ClearFog make sure that SATA and UART images are buildable
SATA and UART ClearFog imaages are not buildable as ENV_SECT_SIZE is not defined
set values for both possible targets

Signed-off-by: Dennis Gilmore <dennis@ausil.us>
2021-01-27 07:25:39 +01:00
Dennis Gilmore
5a3db5d1af ARM: mvebu: helios4 adjust env sizes to enable SPI to work
mirror the clearfog setup to enable SPI to work

Signed-off-by: Dennis Gilmore <dennis@ausil.us>
2021-01-27 07:25:39 +01:00
Tom Rini
e262b2973e Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxi
- New Allwinner H616 SoC support (sans Ethernet & USB)
- H6 DT update
- Tanix TX6 TV box support
- OrangePi 3 support
- OrangePi Zero2 (H616) support
2021-01-25 19:46:02 -05:00
Jernej Skrabec
38be6b8387 sunxi: Add support for OrangePi Zero2
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.

The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.

[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:01 +00:00
Jernej Skrabec
d0b07c15c2 sunxi: add support for R_I2C on H616
This port is needed for communication with PMIC. SPL uses it to set DRAM
voltage on H616 boards.

Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:01 +00:00
Jernej Skrabec
fbd37d8d28 sunxi: Add support for AXP305 PMIC
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:00 +00:00
Andre Przywara
e9ad1b8dc5 sunxi: Properly check for SATAPWR and MACPWR
The #ifdef CONFIG_xxxPWR conditionals were not working as expected, as
string Kconfig symbols are always "defined" from the preprocessor's
perspective. This lead to unnecessary calls to the GPIO routines, but
also always added a half a second delay to wait for a SATA disk to power
up. Many thanks to Peter for pointing this out!

Fix this by properly comparing the Kconfig symbols against the empty
string. strcmp() would be nicer for this, but GCC does not optimise this
away, probably due to our standalone compiler switches.

Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi WinPlus
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
2021-01-25 21:52:00 +00:00
Andre Heider
c81877a919 sunxi: Add support for Orange Pi 3
dts file is taken from Linux 5.11-rc1 tag.

The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:00 +00:00
Jernej Skrabec
a54b2925a6 sunxi: Add support for Tanix TX6
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.

DT file is taken from Linux 5.11-rc1 release.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:00 +00:00
Tom Rini
c99be953e7 - MIPS: add support for Mediatek MT7620 SoCs
-----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAmAN21EACgkQKPlOlyTy
 XBgzBw/+LUzGufIop4CimnEhqrfKRuoSKinRWhx8Lo4PyjF5SAwLgIyCWY95PoQf
 eDka+Ufyj1TbvqbPR+bhJbdL7wFrku3iKE7b0Ni8AamkmsyybxAVeyByen0Q1mSF
 q4KoPhKJmpdZOfrUVrXZBBwG7/T1WTHMrCc2ZSacR0G/IeimgLplT4sRk/uG1eFo
 uiKYf0/AjD28WNvlE9Dq0EZQA+KsTe/q7GQ79nOTuxYTOjbPA59WXTOtZMo1cPgc
 GhT1EJr4N7OcGvxgkiZ8Gs4mYMbFFVvMAUNW1Bsx4v1aYJyfgP0ua58gTnWSMn69
 OJNdxTs+JYBSIZd0B8gNf0P1ZQgrGACA1Vq4O3xJUImtkzp0tMID97ZwvAdhJQbo
 MhNrWcIxijrzWDHEGhnyZ0wyqWmSwznsrvIlS9hMuIxxmnYKveTwfkCeVcvkwvn7
 Nc1Pls1Lt2ViP8/Nygc+fAMg30vtp+NvSrbA53foka62sJMqmWAjPEprPPlJV0Z2
 qGJWCxIJ/1YAUjkNrEnSo/2A3SSAM8wA1ku6aT/Ju7NZCx/3m7sYXE+wQuxYlU2I
 zxQDO+2H0v0nlVVWebQZGZx8sn6Z4O+aGCLAkpJ9tqrViJYhy0Ti2QZi0Udcl1Ny
 lADQXQM2iPoQ2zJlO4AmzXCZ7DLrKVeS3hFFiVxRWK16apckz+o=
 =fKDK
 -----END PGP SIGNATURE-----

Merge tag 'mips-pull-2021-01-24' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips

- MIPS: add support for Mediatek MT7620 SoCs
2021-01-25 14:38:40 -05:00
Tom Rini
4057b98ff2 Changes for 2020.04
-------------------
 
 - new board:
 	Phytec phyCORE-i.MX8MP
 	i.MX8MN Beacon EmbeddedWorks devkit
 
 - Fixes:
 	several nanbcb fixes
 	fix for imx8mm_beacon
 - further switch to distro boot commands
 - DM:
 	DM Ether for MX6UL
 
 CI:
 
 https://gitlab.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/6013
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYA7Oxw8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76bFkACePFxGqlRiC88QcA42wgCbCEmsdtEAnR4TgXQ4
 aMH4tzrcK9Qvs7ULooDL
 =IZtF
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20210125' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

Changes for 2020.04
-------------------

- new board:
	Phytec phyCORE-i.MX8MP
	i.MX8MN Beacon EmbeddedWorks devkit

- Fixes:
	several nanbcb fixes
	fix for imx8mm_beacon
- further switch to distro boot commands
- DM:
	DM Ether for MX6UL

CI:

https://gitlab.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/6013
2021-01-25 09:02:35 -05:00
Tom Rini
aee5bcce35 Second set of u-boot-atmel features for 2021.04 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
 aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
 vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
 mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
 gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
 NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
 8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
 p1e3
 =xS6A
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel

Second set of u-boot-atmel features for 2021.04 cycle

This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
2021-01-25 09:01:28 -05:00
Weijie Gao
76880b08c4 mips: mtmips: add two reference boards for mt7620
The mt7620_rfb board supports integrated 10/100M PHYs plus two external
giga PHYs. It also has 8MB SPI-NOR, mini PCI-e x1 slot, SDHC and USB.

The mt7620_mt7530_rfb boards supports an external MT7530 giga switch and a
16MB SPI-NOR flash.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24 21:39:26 +01:00
Adam Ford
8e95883e46 imx: Add support for i.MX8MN Beacon EmbeddedWorks devkit.
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.

The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2021-01-23 14:01:49 +01:00
Marc Ferland
5df34feb24 arm: dart6ul: fix ddr size macro
The previous macro was off by one bit and so we were getting a ddr
size which was twice the real size. This commit refactors the macro so
it returns the right size in _bytes_ and modifies the printf call so the
size is still printed in MiB.

Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
2021-01-23 13:47:50 +01:00
Teresa Remmet
c661c511e9 board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support
Add initial support PHYTEC phyCORE-i.MX8MP SOM.

    Supported features:
     - 2GB LPDDR4 RAM
     - eMMC
     - external SD
     - debug UART2
     - watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-01-23 11:30:32 +01:00
Marc Ferland
9452d58e10 arm: dart6ul: enable DM_ETH for the dart6ul
This patch converts the dart6ul ethernet support to DM_ETH and cleans
up the legacy ethernet code. The clean up, more specifically:

* moves the fec2 node and pin definition to the carrier board DTS
  since the phy associated with it is on the carrier board and not on
  the SoM;
* add the reset pin associated to each phy;
* separate the ethernet, mdio and reset pins of each fec so that they
  are easier to reference;
* add clock properties to the phy nodes since they are connected to the
  50Mhz ENET[12]_TX_CLK clock of the SoC;
* remove CONFIG_BOARD_EARLY_INIT_F since the function is now empty.

Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
2021-01-23 11:30:31 +01:00
Alice Guo
10a394ba68 board: imx8mp: add boot.cmd for distro boot on iMX8MP
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg

The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value
"/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.

Signed-off-by: Alice Guo <alice.guo@nxp.com>
2021-01-23 11:30:31 +01:00
Alice Guo
9b8656bd2b board: imx8mm: add boot.cmd for distro boot on iMX8MM
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg

The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value "
/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
2021-01-23 11:30:31 +01:00
Peng Fan
846b77e7df imx: imx8mn_ddr4_evk: Use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board
use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use
CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-23 11:30:30 +01:00
Peng Fan
48b90f86c5 imx: imx8mp_evk: enable eth support
Add board code to configure the network interface
Add net defconfig

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-23 11:30:30 +01:00
Tom Rini
abd95385e7 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-samsung.git 2021-01-22 16:01:27 -05:00
Greg Gallagher
9119800591 board: atmel: Add SAMA5D27 giant board
Giant board is a tiny SBC based on the Adafruit Feather form factor,
created by groboards it contains a SAMA5D2 processor (SAMA5D27),
128 MB of RAM and a microSD card for storage.

Signed-off-by: Greg Gallagher <greg@embeddedgreg.com>
2021-01-22 15:09:59 +02:00
David Bauer
b821e0db46 rockchip: rk3328: Add support for FriendlyARM NanoPi R2S
This adds support for the NanoPi R2S from FriendlyArm.

Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED

Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2021-01-21 11:58:35 +08:00
Michal Simek
a672b9871b xilinx: common: Do not touch CONFIG_XILINX_OF_BOARD_DTB_ADDR in SPL
This hook is used in full U-Boot that's why there is no reason to touch
this location from SPL. The hook was introduced for QEMU usage but none is
really running SPL on QEMU that's why it shouldn't break any usecase.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-20 08:34:53 +01:00
Michal Simek
506009fc10 xilinx: common: Change macro handling in board_fdt_blob_setup()
Remove ifdef logic which is handled by preprocessor and move it link time
optimization to get full compile code coverage.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-20 08:34:53 +01:00
Michal Simek
2784befbd7 xilinx: zynqmp: Save bootseq number for SD/EMMC boot modes
For systems which has both sdhci controllers enable it is worth to export
bootseq number for variables. Then the variable can be used in custom
scripts to tune logic for OS.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-20 08:34:53 +01:00
Chia-Wei, Wang
ccdb58dc0a configs: aspeed: Add defconfig for AST2600 EVB
Add the default configuration for the AST2600 EVB.

Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
2021-01-18 15:23:06 -05:00
Chia-Wei, Wang
4a84cf06aa aspeed: Add AST2600 platform support
Add low level platform initialization for the AST2600 SoC.
The 2-stage booting with U-Boot SPL are leveraged to support
different booting mode.

However, currently the patch supports only the booting from
memory-mapped SPI flash.

Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
2021-01-18 15:23:06 -05:00
Holger Brunck
cbfc3b76b0 km/kirkwood: enable USB support and the host controller driver
Our kirkwood device embeds a USB host controller that is now used
on some boards. This enables the support of USB and the corresponding
driver.

Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-01-18 15:14:15 -05:00
Fabien Parent
c2984eb38e board: mediatek: pumpkin: initialize usb device
Initialize USB device on pumpkin if it is enabled in the config.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
2021-01-18 14:59:19 -05:00
Padmarao Begari
64413e1b7c riscv: Add Microchip MPFS Icicle Kit support
This patch adds Microchip MPFS Icicle Kit support. For now, only
NS16550 Serial, Microchip clock, Cadence eMMC and MACB drivers are
enabled. The Microchip MPFS Icicle defconfig by default builds
U-Boot for S-Mode because U-Boot on Microchip PolarFire SoC will run
in S-Mode as payload of HSS + OpenSBI.

Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
2021-01-18 11:06:38 +08:00
Sean Anderson
8f78e52794 riscv: Add support for SPI on Kendryte K210
This enables configs necessary for using SPI. The environment is saved to
the very end of SPI flash. This is unlikely to be overwritten unless the
entire flash is reprogrammed.

This also supplies a default bootcommand. It loads an image and device tree
from the first partition of the MMC. This is a minimal/least effort
bootcmd, so suggestions (especially in the form of patches) are welcome. I
didn't set up distro boot because I think it is unlikely that any
general-purpose linux distros will ever be ported to this board.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Chrstopher Obbard <obbardc@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2021-01-18 11:06:26 +08:00
Tom Rini
83e13c3469 Merge branch '2021.04-rc' of https://github.com/lftan/u-boot
- Add ATF flow for SoC64 devices
- Update socfpgaimage to support print header and update padding flow
2021-01-15 07:55:11 -05:00
Tom Rini
ab1a425524 - Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
 - Activate OF_LIVE for ST stm32mp15 boards
 - Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
 - Correction in stm32prog command on uart: always flush DFU on start command
 - Update USB-C power detection algorithm on DK boards
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/+yLkACgkQ4rK92eCq
 k3X/Fgf/d/11WyQrVzvpr+nN+4Wl7J+ASmoUz0yKa6ri+lbvhLgh+JXbCRKgRPWu
 vNnI07pSoX/QeaMpGBU8Ztg/Onb9/pvffz4WMk1411GoyCpDFuuK3cVSIoqkPfu+
 XmgSX0u4BXtve1+ZdWfVBWXawUSEDMmGR3tmz1708c/s/oYpnVeRDcqiqzJ94cWE
 yt+SpMPVqMUVQ/rAGkE8ToSMxX7FusEa7SvCg4U2ikoRWs3kPpr/73+tRWlmgGxL
 sW8SXSKiOmFyheSBx3d2B9n00kDYTTrQmbW9hlMilZmji7CwZYxgTCMdX0x4DeFP
 RDajT2Yju1JmeM+Z8+Ke2tupzvy6QA==
 =oK8C
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20210113' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
2021-01-13 15:00:53 -05:00
Tom Rini
795f8fd0b5 - sync amlogic GX & AXG DT to Linux 5.10
- Add new MESON_EE driver support for GXBB & AXG
 - Add support for Libretech-CC v2, Wetek Core2, Beelink GT-King/Pro boards
 - add driver for TDO tl070wsh30 panel driver
 - meson: isolate loading of socinfo
 - Add soc_rev to environment
 - Enable G12A support for saradc
 - Add correct mmcdev on VIM3(L) & Odroid-N2(C4)
 - Read MAC from fuses for VIM3 & VIM3L boards
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAl/9rV0ACgkQd9zb2sjI
 SdFE0xAAtXzW98pKmC4C3a1FWcGSuBZK2gzUgKc8oTqBWodMTVLSmDGNbIpaES/+
 UySXSR0KJ5Qmu3jEZN2NYUKuABzylmIyT+5/sj1yN0zgxU2NB2//18uELNVKC4b+
 wtLna+SSebl8ofGuVzfYYCfbBS0S2Y+n9g2+WVu3s+D03WG5wrqEZy5RqKRf4OMZ
 MoQiDoLFms1GS6iLoidg/RMNme6efODAOTOVklHre2zeN3rjGei2URHdVtIeXcdG
 G3Wz9GVwR96UWTGY6JuXEGVpI459vHc4AcswnVcKNnILS/50tpSA9Gc0e0lXaDwT
 29DPehnoBkdbtIQ4szrAthGBITWhhgp2ksHaY5jyg38mVGF1/uu76kPUlCLxY5fL
 //3j/t+qaA3iwJq36tvZSKbprjA8sINN8Hsmi9+2Bzyv90sLfxY/x/DpeTVfWUQf
 UireG3iCYBkP5Mxr1kO+eJUoPAEe8BDJ+3AyVCjlMvKdomGFGCY0C/2LY54G8WS+
 el2Sj8XkTgtZQA/HXuXg1y2Cw54FWN6SXMVFXqZW5bu/w2GmeSOMEkFs3aFieCB7
 5UP+PiA3aM9Z6oXJReNnwc7iy+de8peZ/gpNCqWxr/jxg/C5d+Lg3kgbr961MyhU
 e97xab9p3f9raVOrYCAP7jVqAfTS39ZtAzSZlSJcK3Pls9wVxJI=
 =iIWq
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20210112' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic

- sync amlogic GX & AXG DT to Linux 5.10
- Add new MESON_EE driver support for GXBB & AXG
- Add support for Libretech-CC v2, Wetek Core2, Beelink GT-King/Pro boards
- add driver for TDO tl070wsh30 panel driver
- meson: isolate loading of socinfo
- Add soc_rev to environment
- Enable G12A support for saradc
- Add correct mmcdev on VIM3(L) & Odroid-N2(C4)
- Read MAC from fuses for VIM3 & VIM3L boards
2021-01-13 07:32:02 -05:00
Patrice Chotard
7ccaa31380 MAINTAINERS: Update STi and STM32 maintainers emails in remaining files
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-01-13 09:52:58 +01:00
Michal Simek
635e233b22 ARM: stm32: Use firmware property instead of loadables
There shouldn't be a need to use loadables propertyn because u-boot can be
pointed by firmware property. This change should also speedup boot process
because loadables property is list of strings which code is going through.
On the other hand firmware can just point to one image.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13 09:52:58 +01:00
Patrice Chotard
42082bc61b board: stm32pm1: update USB-C power detection algorithm on DK boards
USB-C power supply which are Power Delivery compliant (USB-PD) are able
to provide different voltage/current (for example 5V/3A 9V/3A 12V/2.25A...)

In this case, the power supply need to negotiate the voltage/current to
use with the device using CC1/CC2 USB-C signals.

If this negotiation occurs during ADC measurement (done also on CC1/CC2
USB-C signals) some ADC acquisition can be corrupted which cause wrong
power supply current detection.

To avoid this, the power supply current detection algorithm is updated
as following:
  - perform an ADC measurement, if a 3A current is detected, continue the
    boot process.
  - else, wait 20ms (max tPDDebounce duration) to ensure that USB-PD
    negotiation is done and perform another ADC measurement.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2021-01-13 09:52:58 +01:00
Patrick Delaunay
705b5bf9bb board: st: common: migrate trace to dev and log macro
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13 09:52:58 +01:00
Patrick Delaunay
873bf44888 board: st: stm32mp1: migrate trace to dev and log macro
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13 09:52:58 +01:00
Jaehoon Chung
a654b6a5ae samsung: arndale: remove board_mmc_init function
Remove board_mmc_init function.
It will be probed with driver-model.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2021-01-13 13:49:38 +09:00
Tom Rini
ee6726be4f Merge tag 'ti-v2021.04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- DM support for OMAP PWM backlight
- USB host mode support for AM654
- Minor SPI fixes
- Add support k2g ice board with 1GHz silicon
- Fix GTC programming for K3 devices
2021-01-12 09:32:48 -05:00
Tom Rini
996f217ea3 First set of u-boot-atmel features for 2021.04 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/8S/0cHGV1Z2VuLmhy
 aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKFkB/9NBJq/+sgHZXRaMlAu
 ULNwOPoNsQxHQGwF88B1lC+H8LJjM+2gJ8MfJdWvHNlcSdtJjbWk0aQL+5LKSlyz
 G7l3BZ+AIYMOeTXay5mNUKnekXIr7c8tLoX8FH/Ih+bHFPt57qL0bbfznV66UCOp
 /o/yM8daPa9Kx1vPEpT2dC9bYXLXeQv6R+RMxwoc4Bk+R3OK7zoZ3Wdx0q9HvBwj
 iWHM49X2fBqqi5RS+ZI37AUzi8iysD3fOq0kWTJcCNaci8i8RZdzSyoaDuXhA63I
 EZJ7v9fUkW/bwTONVE9n2BX4xF9X/6R7P46l9dQISXAxsOBwsNRQPt8Ro7mCoc4K
 392o
 =LIK7
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-atmel-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel

First set of u-boot-atmel features for 2021.04 cycle

This feature set includes the new board SAMA7G5 EK, the new evaluation
kit for Microchip AT91 SAMA7G5 SoC . The current board support includes
two configurations for booting from eMMC (SDMMC0), SD-Card (SDMMC1), and
support for two Ethernet interfaces.
2021-01-12 09:32:20 -05:00
Artem Lapkin
6bfa331a6e board: amlogic: vim3: fix setup ethernet mac from efuse
Fix reading built-in ethernet MAC address from efuse

NOTE: MAC is stored in ASCII format, 1bytes = 2characters by 0 offset

if mac from efuse not valid we use meson_generate_serial_ethaddr

NOTE: remake odroid-n2.c from Neil Armstrong <narmstrong@baylibre.com>

Signed-off-by: Artem Lapkin <art@khadas.com>
[narmstrong: remove MAC print & spurious new endline]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-12 14:25:55 +01:00
Dario Binacchi
ba149a5b7b board: ti: am335x-ice: get CDCE913 clock device
With support for other clock drivers, the potentially supported CDCE913
device can no longer be probed without specifying its DT node name.

Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-01-12 10:59:04 +05:30
Dario Binacchi
260cbc9af2 video: omap: move drivers to 'ti' directory
Add drivers/video/ti/ folder and move all TI's code in this folder for
better maintenance.

Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-01-12 10:59:04 +05:30
Lokesh Vutla
d2aa5727a5 board: ti: k2g: Add support for K2G ICE with 1GHz Silicon
Add board detection support for K2G ICE with FlagChip 1GHz silicon.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-01-12 10:21:41 +05:30
Aswath Govindraju
6f9d41403a board: ti: am65x: Set SERDES0 mux to PCIe to use USB 2.0 interface
It has been observed that setting SERDES0 lane mux to USB prevents USB 2.0
operation on USB0. Setting SERDES0 lane mux to non-USB when USB0 is used in
USB 2.0 only mode solves this issue. However, for USB3.0+2.0 operation this
issue is not present.

Implement this workaround by writing 1 to LANE_FUNC_SEL field in
CTRLMMR_SERDES0_CTRL register.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-01-12 10:21:40 +05:30
Andre Heider
9267ff89ee sunxi: board: add a config option to fixup a Bluetooth address
Some Bluetooth controllers, like the BCM4345C5 of the Orange Pi 3,
ship with the controller default address.

Add a config option to fix it up so it can function properly.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:34 +00:00
Andre Heider
928f4f4868 sunxi: board: extract creating a unique sid into a helper function
Refactor setup_environment() so we can use the created sid for a
Bluetooth address too.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:34 +00:00
Andy Shevchenko
92600edb43 sunxi: board: Move USB ethernet initialization to board_late_init()
For the sake of consistency (*) and order of initialization, i.e.
after we have got the ethernet address, interrupt and timer initialized,
try to initialize USB ethernet gadget.

*) for example, zynqmp uses same order.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:34 +00:00
Icenowy Zheng
ab3b53f30f sunxi: add PineCube board
PineCube is an IP camera development kit released by Pine64.

It comes with the following compoents:

- A mainboard with Sochip S3 SoC, a 16MByte SPI Flash, AXP209 PMIC,
a power-only microUSB connector, a USB Type-A connector, a 10/100Mbps
Ethernet port and FPC connectors for camera and daughter board.
- An OV5640-based camera module which is connected to the parallel CSI
bus of the mainboard.
- A daughterboard with several buttons, a SD slot, some IR LEDs, a
microphone and a speaker connector.

As the device tree is synchronized in a previous commit, just add it to
Makefile, create a new MAINTAINER item and provide a defconfig.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:33 +00:00
Tom Rini
d71be19902 Merge branch 'next'
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-11 13:55:03 -05:00
Marek Szyprowski
aa3c7912cb board: amlogic: add MMC boot device detection for environment load
Detect eMMC or SD card boot on Odroid-C4/N2 and Khadas VIM3(l) boards and
report proper MMC device for the environment loading code. This allows to
automatically load and store environment variables on the FAT partition
or RAW offset of the MMC device without the need to use different
configurations on eMMC and SD card.

To use this feature with environment stored on FAT partition, one has to
specify an empty device part (i.e. ":1" for the first partition) in
CONFIG_ENV_FAT_DEVICE_AND_PART to let the code to set the device to the
value returned by mmc_get_env_dev() function.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:55 +01:00
Christian Hewitt
b3be2ee656 boards: amlogic: add Beelink S922X board family support
Copied from Odroid N2. Add myself as maintainer.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Marek Szyprowski
d10037e976 board: amlogic: vim3: read ethernet MAC address from efuse
Add the board specific code for reading built-in ethernet MAC address
from efuse.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Christian Hewitt
d412a6015e boards: amlogic: update documentation for WeTek Core2
Update the device matrix and add build instructions.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: added wetek-core2.rst to q200 MAINTAINERS and added blank lines to fix build]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Christian Hewitt
ed430519cf boards: amlogic: add WeTek Core2 support
Add a config for the WeTek Core2, largely based on the VIM2 config.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: added wetek-core2_defconfig to q200 MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Pascal Vizeli
d42e7964d9 meson: Add soc_rev to environment
Add SoC revision to environment. This can be useful to select the
correct device tree at runtime (N2/N2+).

Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Jerome Brunet
ade0100a91 arm64: meson: add support for libretech-cc v2
Add support for the Amlogic based libretech cc version 2.
As version 1, it is based on the s905x SoC.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: Fixed libretech-cc.rst bullet points]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Lukasz Majewski
a062d8e610 xea: spl: Disable pull UP for GPIO0_2{35}
On the imx287 pin GPMI_WRN (GPIO0_25) no PullUP is available that can be
enabled.

To get the same behavior for both boot select pins (i.e. GPIO0_2{35})
disable pull UPs on both.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2021-01-08 08:41:50 -05:00
Eugen Hristev
a07d2a1121 board: atmel: sama7g5ek: add support for MAC address retreival
Obtain two MAC addresses from the two EEPROMs and configure the two
available Ethernet interfaces accordingly.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-01-07 09:44:16 +02:00
Eugen Hristev
0f8904b82d configs: sama7g5: add mmc config for sdmmc0
Add new config for storing environment from sdmmc0.
Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-01-07 09:44:16 +02:00
Eugen Hristev
1d463d6735 board: atmel: sama7g5ek: add initial support for sama7g5ek
Add initial support for sama7g5 evaluation kit board.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-01-07 09:44:15 +02:00
Tom Rini
bc0b99bd8b Xilinx changes for v2021.04
arm64:
 - DT updates
 
 microblaze:
 - Add support for NOR device support
 
 spi:
 - Fix unaligned data write issue
 
 nand:
 - Minor code change
 
 xilinx:
 - Fru fix in limit calculation
 - Fill git repo link for all Xilinx boards
 
 video:
 - Add support for seps525 spi display
 
 tools:
 - Minor Vitis file support
 
 cmd/common
 - Minor code indentation fixes
 
 serial:
 - Uartlite debug uart initialization fix
 -----BEGIN PGP SIGNATURE-----
 
 iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
 IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
 =4FnY
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2021.04

arm64:
- DT updates

microblaze:
- Add support for NOR device support

spi:
- Fix unaligned data write issue

nand:
- Minor code change

xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards

video:
- Add support for seps525 spi display

tools:
- Minor Vitis file support

cmd/common
- Minor code indentation fixes

serial:
- Uartlite debug uart initialization fix
2021-01-06 07:57:33 -05:00
Tom Rini
b11f634b1c Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
 dtoc: Tidy up and add more tests
 ns16550 code clean-up
 x86 and sandbox minor fixes for of-platdata
 dtoc prepration for adding build-time instantiation
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
 KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
 HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
 59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
 2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
 LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
 =9kN3
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next

Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
2021-01-05 22:34:43 -05:00
Tom Rini
720620e691 Prepare v2021.01-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAl/0YVIACgkQFHw5/5Y0
 tywtEwv/cJWlKgcSnYjuJrxwuJdauUTfXdbUgtCxOtBw/BP4dsKkbGTJPw5q5M+4
 LJJSKyksmJVTX26h1dpkzQjOpWtTDnWqm5CTIxD52oQD7pxK+zCQ9T6S+QbQD0Se
 ogHmZluzFoluxbNgo8tiO52xvMhDO3TVAzxsNDdGfkd5/tAXOHClPc34RmAkdRHU
 VsR89AKdT2q543fiUfrRZYDzdctaNWhRGXMDcJ4+QU/8hQhrpcr8EtHbF+3mWX4K
 pA01pDz150Rn4UI6S2xKEWrjSTHe55fxVj/Qj0rq9z2E/+NqGXemf5s13AR0G/z3
 PqHdVLHzDe64pbOvmyU1pVQ0aMb8vMJUnqx68SQZY3On2c+MjRWQ+7aVVaKOcPGp
 uatk6QMrggHp3Li+3yZrLBE0qPr/sNMVb7mUesdZb6lFd2VIs8siwhfeGXMS+nDI
 xePzsR43Fnn5Q5KIqqvcWUb+TTTqUDUff0wyAU8NBgCaIBIZK8h2ppS1jjnbms0I
 mr8Er2vb
 =Dfum
 -----END PGP SIGNATURE-----

Merge tag 'v2021.01-rc5' into next

Prepare v2021.01-rc5

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-05 16:20:26 -05:00
Tom Rini
c2d80bbde8 Merge tag 'ti-v2021.01-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Fix I2C speed for Nokia RX51
2021-01-05 16:10:33 -05:00
Simon Glass
65e25bea59 dm: Rename DM_GET_DRIVER() to DM_DRIVER_GET()
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:26:35 -07:00
Simon Glass
20e442ab2d dm: Rename U_BOOT_DEVICE() to U_BOOT_DRVINFO()
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.

The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)

It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.

Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:26:35 -07:00
Simon Glass
f10643cf8a dm: core: Access device ofnode through functions
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:24:41 -07:00
Simon Glass
8b842be10c x86: apl: Reduce size for TPL
Update various drivers to use of_match_ptr() and to avoid including debug
strings in TPL. Omit the WiFi driver entirely, since it is not used in
TPL.

This reduces the TPL binary size by about 608 bytes.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:24:41 -07:00
Simon Glass
2d6bf754ce serial: Rename ns16550 functions to lower case
Lower case should be used for function names. Update this driver and its
callers accordingly.

Signed-off-by: Simon Glass <sjg@chromium.org>

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2021-01-05 12:24:40 -07:00
Simon Glass
d30c7209df serial: Update NS16550_t and struct NS16550
Typedefs should not be used in U-Boot and structs should be lower case.
Update the code to use struct ns16550 consistently.

Put a header guard on the file while we are here.

Signed-off-by: Simon Glass <sjg@chromium.org>

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2021-01-05 12:24:40 -07:00
Pali Rohár
a8ef64e4ef Nokia RX-51: Decrease i2c speed to 100000
It looks like that i2c bus lot of times timeout on some units. Prior
migration to CONFIG_DM_I2C i2c speed was set to CONFIG_SYS_OMAP24_I2C_SPEED
value which was 100000. Lower speed fixes timeout problems, so change speed
back to its previous value.

Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 8d8c181703 ("Nokia RX-51: Convert to CONFIG_DM_I2C")
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-01-05 20:49:52 +05:30
Michal Simek
0109db1cd1 xilinx: Fill git repository for Xilinx boards
All Xilinx SoCs have repository location filled already but boards are
covered by different fragment which is missing this link.
The patch is extending description with adding proper link to the same
repository.

Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-05 11:54:53 +01:00
Heinrich Schuchardt
b6d14c52f9 fru: ops: avoid out of bounds access
Building xilinx_zynq_virt_defconfig fails on origin/next as reported by
GCC 10.2 (as provided by Debian Bullseye):

  CC      board/xilinx/common/fru_ops.o
board/xilinx/common/fru_ops.c: In function ‘fru_capture’:
board/xilinx/common/fru_ops.c:173:8:
error: array subscript 284 is outside array bounds of
‘struct fru_table[1]’ [-Werror=array-bounds]
  173 |  limit = data + sizeof(struct fru_board_data);
      |  ~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
board/xilinx/common/fru_ops.c:17:18: note: while referencing ‘fru_data’
   17 | struct fru_table fru_data __section(.data);
      |                  ^~~~~~~~

When using sizeof(struct fru_board_data) to find the end of the structure
you should add it to the start of the structure.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-05 11:54:53 +01:00
T Karthik Reddy
5766429b7c microblaze: Set script_offset_nor env variable
Set script_offset_nor env variable using CONFIG_BOOT_SCRIPT_OFFSET
and nor flash start address to keep bootscript offset configurable.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-04 10:51:27 +01:00
Sughosh Ganu
04be98bd6b efi: capsule: Add support for uefi capsule authentication
Add support for authenticating uefi capsules. Most of the signature
verification functionality is shared with the uefi secure boot
feature.

The root certificate containing the public key used for the signature
verification is stored as part of the device tree blob. The root
certificate is stored as an efi signature list(esl) file -- this file
contains the x509 certificate which is the root certificate.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
2020-12-31 14:41:31 +01:00
Sughosh Ganu
cc02f15faa qemu: common: Set dfu_alt_info variable for the platform
The dfu framework uses the dfu_alt_info environment variable to get
information that is needed for performing the firmware update. Add
logic to set the dfu_alt_info for the qemu arm64 platform to reflect
the two mtd partitions created for the u-boot env and the firmware
image. This can be subsequently extended for other qemu architectures
which need this variable set.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
2020-12-31 14:41:31 +01:00
Sughosh Ganu
c89a9873fd qemu: common: Add support for dynamic mtdparts for the platform
Add support for setting the default values for mtd partitions on the
platform. This would be used for updating the firmware image using
uefi capsule update with the dfu mtd backend driver.

Currently, values have been defined for the qemu arm64 platform, with
default values defined for the mtd partitions based on the NOR
flash. This can be subsequently extended for other qemu architectures
which need mtdparts set.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
2020-12-31 14:41:31 +01:00
Sughosh Ganu
e1ee06dde7 qemu: arm: Initialise virtio devices in board_late_init
On the qemu arm platform, the virtio devices are initialised in the
board_init function, which gets called before the initr_pci. With
this sequence, the virtio block devices on the pci bus are not
initialised. Move the initialisation of the virtio devices to
board_late_init which gets called after the call to initr_pci.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
2020-12-31 14:41:31 +01:00
Marc Ferland
37648b600c arm: dart6ul: read and print SoM info from eeprom on startup
The dart6ul has an i2c eeprom at 0x50 which contains, among other
things, the manufacturing/revision/options info of the SoM. This patch
replaces the current checkboard() implementation with a more
exhaustive one based on the content of the eeprom.

Since this code uses the new driver model, some changes were also
required in the DTS to make the nodes related to i2c available before
relocation.

This code was inspired from the supported u-boot code from Variscite
which can be found here:

https://github.com/varigit/uboot-imx/tree/imx_v2018.03_4.14.78_1.0.0_ga_var02

New output example:

Board: PN: VSM-6UL-705B, Assy: AS1812142257, Date: 2019 Feb 17
       Storage: eMMC, Wifi: yes, DDR: 1024 MiB, Rev: 2.4G

Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-12-26 14:56:09 +01:00
Igor Opaniuk
f23c706863 toradex: hand over maintainership
Hand over maintainership of Toradex SoMs (that I was responsible of) to
Oleksandr because of my resignation from Toradex, as such I will
have no immediate involvement with these modules and as a result not
able to continue maintaining these boards.

CC: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-26 14:56:09 +01:00
Sebastian Reichel
717bf50f4b board: ge: bx50v3: cleanup phy config
The current PHY rework does the following things:

1. Configure 125MHz clock
2. Setup the TX clock delay (RX is enabled by default),
3. Setup reserved bits to avoid voltage peak

The clock delays are nowadays already configured by the
PHY driver (in ar803x_delay_config). The code for that
can simply be dropped. The clock speed can also be
configured by the PHY driver by adding the device tree
property "qca,clk-out-frequency".

What is left is setting up the undocumented reserved bits
to avoid the voltage peak problem. I slightly improved its
documentation while updating the board's PHY rework code.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2020-12-26 14:56:09 +01:00
Sebastian Reichel
c44d374bef board: ge: bx50v3: remove confidx magic numbers
Instead of hardcoding index magic numbers in the board code,
also rely on board_fit_config_name_match choosing the right
config for the fitImage containing the kernel.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2020-12-26 14:56:09 +01:00
Fabio Estevam
72397c9621 mx6sabresd: Remove unneeded checkboard()
After the conversion to device tree the board information becomes
redundant:

Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board
Board: MX6-SabreSD

Remove the printing of the board information.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-12-26 12:37:07 +01:00
Heinrich Schuchardt
3286d223fd sandbox: implement invalidate_icache_all()
Before executing code that we have loaded from a file we need to flush the
data cache and invalidate the instruction flash.

Implement functions flush_cache() and invalidate_icache_all().

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-12-22 20:39:25 -07:00
Simon Glass
8b85dfc675 dm: Avoid accessing seq directly
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.

The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-18 20:32:21 -07:00
Andy Shevchenko
f89e8acbc8 x86: edison: Switch to DM_USB_GADGET
DM is the modern default approach for the drivers in U-Boot.
It also allows to configure code via Device Tree.

Move Intel Edison to use DM_USB_GADGET and drop hard coded values.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-12-16 13:51:24 +08:00
Andy Shevchenko
d067fb7636 x86: edison: BINMAN selection is specific to the board
The platforms based on Intel Tangier may have different requirements
how to create bootloader bundle to supply to a device. Currently
the BINMAN approach is for Intel Edison only.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-12-16 13:50:42 +08:00
Simon Glass
8a8d24bdf1 dm: treewide: Rename ..._platdata variables to just ..._plat
Try to maintain some consistency between these variables by using _plat as
a suffix for them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 16:51:09 -07:00
Simon Glass
d1998a9fde dm: treewide: Rename ofdata_to_platdata() to of_to_plat()
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 16:51:09 -07:00
Simon Glass
c69cda25c9 dm: treewide: Rename dev_get_platdata() to dev_get_plat()
Rename this to be consistent with the change from 'platdata'.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 16:51:09 -07:00
Simon Glass
caa4daa2ae dm: treewide: Rename 'platdata' variables to just 'plat'
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).

Rename some of the latter variables to end with 'plat' for consistency.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 16:51:08 -07:00
Simon Glass
41575d8e4c dm: treewide: Rename auto_alloc_size members to be shorter
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.

Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 08:00:25 -07:00
Biwen Li
164941c2c4 net: pfe_eth: read PFE ESBC header flash with spi_flash_read API
Read PFE ESBC header flash with spi_flash_read API
- logs as follows,
  Net:   SF: Detected s25fs512s with page size 256 Bytes, erase size 256
  KiB, total 64 MiB
  "Synchronous Abort" handler, esr 0x96000210
  elr: 000000008206db44 lr : 0000000082004ea0 (reloc)
  elr: 00000000b7ba6b44 lr : 00000000b7b3dea0
  x0 : 00000000b79407e8 x1 : 0000000040640000
  x2 : 0000000000000050 x3 : 0000000000000000
  x4 : 000000000000000a x5 : 0000000000000050
  x6 : 0000000000000366 x7 : 00000000b7942308
  x8 : 00000000b76407c0 x9 : 0000000000000008
  x10: 0000000000000044 x11: 00000000b7634d1c
  x12: 000000000000004f x13: 0000000000000044
  x14: 00000000b7634d98 x15: 00000000b76407c0
  x16: 0000000000000000 x17: 0000000000000000
  x18: 00000000b7636dd8 x19: 0000000000000000
  x20: 00000000b79407d0 x21: 00000000b79407e8
  x22: 0000000040640000 x23: 00000000b7634e58
  x24: 0000000000000000 x25: 0000000003800000
  x26: 00000000b7bdd000 x27: 0000000000000000
  x28: 0000000000000000 x29: 00000000b7634d10

  Code: d2800003 eb03005f 54000101 d65f03c0 (f8636826)
  Resetting CPU ...

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-12-10 13:56:39 +05:30
Madalin Bucur
848a2efd14 board: freescale: powerpc: add support for all RGMII modes
Make sure all RGMII internal delay modes are covered.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-12-10 13:56:39 +05:30
Madalin Bucur
ccedd4ff8e armv8: ls1043/ls1046aqds: add support for all RGMII modes
Make sure all RGMII internal delay modes are covered.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-12-10 13:56:39 +05:30
Priyanka Singh
f6cb837721 board: freescale: vid.c: Initialize variable 'i2caddress'
Initialize variable 'i2caddress' in adjust_vdd() to zero

Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-12-10 13:56:39 +05:30
Biwen Li
e343ae7c96 board/freescale/common: fix a bug that failed to read/write eeprom on ls1021atsn
Fix a bug that failed to read/write eeprom on ls1021atsn

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-12-10 13:56:39 +05:30
Meenakshi Aggarwal
9ed303dfa9 armv8: lx2162aqds: Add support for LX2162AQDS platform
This patch add base support for LX2162AQDS board.
LX2162AQDS board supports LX2162A family SoCs.
This patch add basic support of platform.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: hui.song <hui.song_1@nxp.com>
Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Signed-off-by: Vikas Singh <vikas.singh@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-12-10 13:56:39 +05:30
Meenakshi Aggarwal
3a187cff7a armv8: lx2162a: Add Soc changes to support LX2162A
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.

LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-12-10 13:56:39 +05:30
Tom Rini
2a42de6df1 - Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
 - Enable internal pull-ups for SDMMC1 on DHCOM SoM
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
 k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
 Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
 7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
 8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
 zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
 LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
 =cgbE
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
2020-12-09 11:36:41 -05:00
Patrice Chotard
0f8106f8e0 treewide: Update email address Patrick Delaunay and Patrice Chotard
Update Patrick and my email address with the one dedicated to
upstream activities.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-12-09 10:57:50 +01:00
Manuel Reis
81d4c4e45c add check for ignored CONFIG_ENV_EXT4_DEVICE_AND_PART definition
Check whether user has explicitly defined device and partition where
environment file will be located before using 'auto' i.e. bootable
partition

Voids the need to set such partition as bootable to work with the
'dev:auto' tuple

Signed-off-by: Manuel Reis <mluis.reis@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2020-12-09 10:57:50 +01:00
Tom Rini
19ea606109 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-imx 2020-12-08 09:53:03 -05:00
Tom Rini
ec79f5ce22 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
  threshold configuration (Joshua)
2020-12-07 11:46:12 -05:00
Oliver Graute
eb38171034 doc: board: imx8qm-rom7720-a1.rst: convert readme to reST
Convert README to reStructuredText format.

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
2020-12-07 08:54:20 +01:00
Pali Rohár
061c6d1b23 arm: mvebu: Espressobin: Detect presence of emmc at runtime
Try to initialize emmc in board_late_init() and if it fails then we know
that emmc device is not connected.

This allows to use in U-Boot just one DTS file for all Espressobin variants
and also to correctly set fdtfile env variable for Linux kernel.

Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Reviewed-by: Andre Heider <a.heider@gmail.com>
2020-12-07 07:11:37 +01:00
Luka Kovacic
5115de8d64 arm: mvebu: puzzle-m801: Add a maintainer
Add Luka Perkov to Puzzle-M801 BOARD MAINTAINERS.

Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
2020-12-07 07:11:37 +01:00
Igor Opaniuk
89f7d08b2a colibri-imx8x: add implementation for board_mem_get_layout
Add implementation of board_mem_get_layout for overriding the memory
layout.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-12-06 15:31:37 +01:00
Igor Opaniuk
5d39967dcf apalis-imx8x: add implementation for board_mem_get_layout
Add implementation of board_mem_get_layout for overriding the memory
layout.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-12-06 15:31:37 +01:00
Igor Opaniuk
90311be09f apalis-imx8: add implementation for board_mem_get_layout
Add implementation of board_mem_get_layout for overriding the memory
layout.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06 15:31:37 +01:00
Igor Opaniuk
a51fdba3fa board: toradex: add apalis-imx8x 2gb wb it v1.1a module support
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].

Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU:   NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM:  2 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In:    serial@5a070000
Out:   serial@5a070000
Err:   serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net:   eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot:  0

Functionality wise the following is known to be working:
  - eMMC and MMC/SD card
  - Ethernet (*)
  - GPIOs
  - I2C

Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.

* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.

[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06 15:31:37 +01:00
Marcel Ziswiler
72a1b9a977 verdin-imx8mm: automatic ram size detection
Implement board_phys_sdram_size() to automatically detect Verdin iMX8M
Mini DualLite 1GB vs. Verdin iMX8M Mini Quad 2GB.

Note: This only works if we keep using similar RAM chips!

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06 15:31:37 +01:00
Marcel Ziswiler
2a1a2559fb toradex: tdx-cfg-clock: fix i.mx 8m mini interactive
Now with them first Verdin iMX8M Mini DualLite modules in for bring-up
we got clarity how is_cpu_type() actually behaves.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06 15:31:37 +01:00
Max Krummenacher
b8eecbac6a verdin-imx8mm: spl: enable pca9450 i2c level translator
Enable PCA9450 i2c level translator, as this is used for the
on module ADC.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06 15:31:37 +01:00
Max Krummenacher
423ca964c3 verdin-imx8mm: implement hardware version detection
And select the correct devicetree accordingly by setting the variant
environment variable.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2020-12-06 15:31:37 +01:00
Max Krummenacher
7d43807d6c verdin-imx8mm: spl: switch to pca9450 pmic
V1.1A HW switched the PMIC from BD71837 to PCA9450.

- Disable combined DVS in PCA9450_BUCK123_DVS.
- Increase DDR Voltage to 0.95V as we use a 1.5GHz RAM.
- Configure WDOG_B behaviour.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06 15:31:37 +01:00
Marcel Ziswiler
a5b5ad4d85 toradex: tdx-cfg-clock: add new i.mx 8m mini/plus skus
Add new i.MX 8M Mini/Plus SKUs to ConfigBlock handling:

0058: Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT

0059: Verdin iMX8M Mini Quad 2GB IT

0060: Verdin iMX8M Mini DualLite 1GB WB IT

0061: Verdin iMX8M Plus Quad 2GB

Rename existing SKU (use correct one):
Verdin iMX8M Nano SoloLite 1GB -> Verdin iMX8M Nano Quad 1GB Wi-Fi

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2020-12-06 15:31:37 +01:00
Oliver Graute
ea51af2fdd imx: imx8qm_rom7720_a1: add missing DTS to the MAINTAINERS
add the dts file to the MAINTAINERS entry

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
2020-12-06 15:31:37 +01:00