This patch imports the device tree and required bindings to permit
the device tree to build for the R8Z774A1 (RZ/G2M).
Signed-off-by: Adam Ford <aford173@gmail.com>
Add u-boot,spl-boot-order for ROCKPi N10, so-that it can able
to boot from eMMC and SDMMC in order.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support to enable PCIe for RockPI N10.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support to enable HDMI out for
N10 and N8 combinations SBCs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa dalang carrier board has 2x USB 2.0 and 1x USB 3.0
ports.
This patch adds support to enable all these USB ports for
N10 and N8 combinations SBCs.
Note that the USB 3.0 port on RockPI N8 combination works
as USB 2.0 OTG since it is driven from RK3288.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3288 and rk3288w have a usb host0 ohci controller.
Although rk3288 ohci doesn't actually work on hardware, but
rk3288w ohci can work well.
So add usb host0 ohci node in rk3288 dtsi and the quirk in
ohci platform driver will disable ohci on rk3288.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This sync has changes required to use HDMI CEC pin in U-Boot.
Sync dts from linux v5.8-rc5 commit:
"ARM: dts: rockchip: define the two possible rk3288 CEC pins"
(sha1: 838980dd04e994bf81cf104fa01ae60802146b39)
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.
So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.
- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
GPIO pin change compared to 4B, 4C
So move common nodes, properties into dtsi file and include
on respective variant dts files.
Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI support for the RK3328
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(fix checkpatch error for code ident)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Get the devicetree from mainline Linux and include it for U-Boot uses.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3326 is just a trimmed down px30 from a software perspective,
so the mainline rk3326 dtsi also ist just a tiny addition.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXxCxWw8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76bPyACcDZ8gD9jf1P/Zh+7kqrGdIWwURF8AnAiEtNnu
FhE/WQQj4mAEWE4F2bFE
=7ceG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.10
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
OF graph endpoint connections must be bidirectional and dtc warn if they
are not. i.MX7 based DTs have an error and generate
warnings:
arch/arm/dts/imx7d-sdb.dtb: Warning (graph_endpoint):
/replicator/ports/port@0/endpoint: graph connection to node
'/soc/tpiu@30087000/port/endpoint' is not bidirectional
arch/arm/dts/imx7d-sdb.dtb: Warning (graph_endpoint):
/soc/tpiu@30087000/port/endpoint: graph connection to node
'/replicator/ports/port@1/endpoint' is not bidirectional
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Convert pcm058 support to use device trees and the driver model.
Add rudimentary boot scripts to the environment, expand README.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add Phytec Mira device tree files, for use with pcm058.
>From Linux 5.6, commit 7111951b8d49 upstream
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Sync DT bindings from kernel DT and move them to out of -u-boot.dtsi
files.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Several MMC drivers use GPIO for card detection with cd-gpios property in
the MMC node pointing to a GPIO node. However, as U-Boot tries to save
space by keeping only required nodes using u-boot* properties, several
devices tree result in having only in the MMC node but not the GPIO node
associated to cd-gpios.
This patch, fixes several ocurrence of this issue.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
The spi0 alias is needed by the environment code to retrieve the SPI
flash. This patch adds some -u-boot.dtsi files, providing the spi0
aliases, for all the following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Note that this -u-boot.dtsi files will be removed as soon as the spi0
aliases will be available in the upstream Linux dtsi files.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The helios4 is built on the same microsom as the clearfog, by syncing the config
we enable the same featureset that exists in the som on the helios4. The current
config does not boot as some of the clearfog changes needed to be made on the
helios4 also, generally speaking most changes for the clearfog should also be
made on the helios4.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
The PHY needs a reset in order to be functionnal for U-Boot, add the old
PHY reset bindings for dwmac until we support the new bindings in the PHY node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Odroid C4 is an Amlogic SM1 device, the board config and board documentation
are adapted from the Odroid-N2 support from the same vendor.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: fix odroid-c4.rst typos and structure]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
This imports the changes and the new Odroid-C4 board from the Linux
commit b3a9e3b9622a ("Linux 5.8-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
This patch adds node for ethernet controller found on Action Semi OWL
S700 SoC.
Since, there is no upstream Linux binding exist for S700 ethernet
controller, Changes are put in u-boot specific dtsi file.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
- use OPP information in device tree for 800MHz/650MHz support
- ram: inprovments of test command
- solve boot on closed chip when access to DBGMCU_IDC is protected
- stm32prog command: Add "device anme" during USB enumeration
- update configs: activate WATCHDOG and 'env erase' command,
increase teed partition, support SD card after NOR boot by default and
use env info in env_check
- some sboard cleanups: gpio hog in dh board, specific driver for
type-c stusb1600 controller code in a driver move part of code in spl.c
and in common directory
- fix STM32 compatible for dwc_eth_qos driver
- support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx
drivers
- vrefbuf: fix a possible overshoot when re-enabling
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl8EgGEACgkQ4rK92eCq
k3V7mwf+N5Iq6CbUPP11mFiNgAFZ5+hcn6gBTWvbjnd+oaIp15hiQrUNusGNFxXe
oyM4fvm12tjuWFlA0U6VtiLhuVQB1Yte048oX+edDCCLGwxkp6cKBHtCaGT14XvY
ow60XInv/dlrINumf8isy+5QlLgT1Cb7aGZN1qRHsUtnHB/IC836KO+hukGRUvk3
Lqz+FbHqitKnL+CIboC2+YzXqG6ZXdixFZVVPmTVd34C8hQOdkExJ//uR/lH/s6f
vjaecs7HpIuKRpKpt5WcoLzTLd1hstqNNhmTbBHmVo+EqIjMkpISUwDpDJNU5pki
BPbdG9VXqb46JLaTtPT+U4gX4yJ3Bw==
=jQCC
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200707' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- arch and board update for stm32mp15:
- use OPP information in device tree for 800MHz/650MHz support
- ram: inprovments of test command
- solve boot on closed chip when access to DBGMCU_IDC is protected
- stm32prog command: Add "device anme" during USB enumeration
- update configs: activate WATCHDOG and 'env erase' command,
increase teed partition, support SD card after NOR boot by default and
use env info in env_check
- some sboard cleanups: gpio hog in dh board, specific driver for
type-c stusb1600 controller code in a driver move part of code in spl.c
and in common directory
- fix STM32 compatible for dwc_eth_qos driver
- support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx
drivers
- vrefbuf: fix a possible overshoot when re-enabling
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl8DHgAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyAdDCACFX01IPRmdkNEYrJf0
YfhQPAPZ/5EyHBv36ePl93CbIRnJPpnrGbBXe8+/Jdcq7l6EkJh2cuO+t9axXner
m0kH35LzLiR9Olz6q5Su0InPWpnDtXxtIczK5v7ZHBeMZ2so763e7SQ2VIMyJJb/
VT6hilqJK6+W1c2X1wmzxyh/nnv/bDBz97cavJN1EKw1arYr8jh/8/tpABk5msDm
J6Z5WsS/CYk7cj6hX7dSNRfqcKsjl/gCYjnVssfgaP1sH+NX0mtS8C6zchNILmpB
2T/dKnpYBBAWTD5fGNVKxKphAuZgQHw51AJhkOnYDrMKisifFC0ssvxkh+nvwyTm
1w4R
=1YzJ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.10 cycle
This patch allows to switch the CPU frequency to 800MHz on the
ST Microelectronics board (DK1/DK2 and EV1) or dh electronics SOM
using the STM32MP15x SOC and when it is supported by the HW
(for STM32MP15xD and STM32MP15xF).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This commit adds cpufreq support on stm32mp15x SOC. STM32 cpufreq uses
operating points V2 bindings (no legacy). Nvmem cells have to be used to
know the chip version and then which OPPs are available. Note that STM32
cpufreq driver is mainly based on "cpufreq-dt" driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the bsec driver in SPL, as it is needed by SOC part number detection
to found the supported OPP.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Rock Pi N8 is a Rockchip RK3288 based SBC, which has
- VMARC RK3288 SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3288 SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N8 SBC.
So, add initial support for Rock Pi N8 by including rk3288,
rk3288 vamrc-som and raxda dalang carrier board dtsi files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
VMARC RK3288 SOM is a standard SMARC SOM design with
Rockchip RK3288 SoC, which is designed by Vamrs.
Specification:
- Rockchip RK3288
- PMIC: RK808
- SD slot, 16GiB eMMC
- 2xUSB-2.0, 1xUSB3.0
- USB-C for power supply
- Ethernet, PCIe
- HDMI, MIPI-DSI/CSI, eDP
Add initial support for VMARC RK3288 SOM, this would use
with associated carrier board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa dalang carrier boards are used to mount vmarc SoM's
of rk3399pro and rk3288 to make complete SBC.
Among these combinations, card detection gpio, max-frequency
properties are used with rk3399pro SoM but not required for
rk3288 SoM based on the hardware schematics.
So, let's move these sdmmc specific properties on associate
vmarc dtsi to make common use of dalang carrier device tree file.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock Pi N10 is a Rockchip RK3399Pro based SBC, which has
- VMARC RK3399Pro SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3399Pro SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N10 SBC.
So, add initial support for Rock Pi N10 by including rk3399,
rk3399pro vamrc-som and raxda dalang carrier board dtsi files.
rk3399pro-rock-pi-n10.dts was synced from linux-next v5.7-rc1.
Tested
- ROCK PI N10 Model B
- ROCK PI N10 Model C
- Boot from SD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Carrier board often referred as baseboard. For making
complete SBC or any other industrial boards, these
carrier boards will be used with associated SOMs.
Radxa has Dalang carrier board which supports on-board
peripherals, ports like USB-2.0, USB-3.0, HDMI, MIPI DSI/CSI,
eDP, Ethernet, WiFi, PCIe, USB-C, 40-Pin GPIO header and etc.
Right now Dalang carrier board is used with two SBC-variants:
Rock Pi N10 => VMARC RK3399Por SOM + Dalang carrier board
Rock Pi N8 => VMARC RK3288 SOM + Dalang carrier board(+codec)
So add this carrier board dtsi as a separate file in
ARM directory, so-that the same can reuse it in both
rk3288, rk3399pro variants of Rockchip SOMs.
Sync this dtsi from linux-next v5.7-rc1.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
VMARC RK3399Pro SOM is a standard SMARC SOM design with
Rockchip RK3399Pro SoC, which is designed by Vamrs.
Specification:
- Rockchip RK3399Pro
- PMIC: RK809-3
- SD slot, 16GiB eMMC
- 2xUSB-2.0, 1xUSB3.0
- USB-C for power supply
- Ethernet, PCIe
- HDMI, MIPI-DSI/CSI, eDP
Add initial support for VMARC RK3399Pro SOM, this would use
with associated carrier board.
Sync this dtsi from linux-next v5.7-rc1.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some minor fixes for SPI flash on the Pinebook Pro and also
default to saving environment to the SPI flash as it's
guaranteed to be on board.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(applied with make savedefconfig)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable the rng so UEFI can provide entropy for KASLR
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----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=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
Since commit:
commit 6333cbb381
Author: Michael Walle <michael@walle.cc>
Date: Thu May 7 00:11:58 2020 +0200
phy: atheros: ar8035: remove static clock config
We can configure the clock output in the device tree. Disable the
hardcoded one in here. This is highly board-specific and should have
never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably
depends on the clock output of your Atheros AR8035 PHY. Please have a
look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set
"clk-out-frequency = <125000000>" because that value was the hardcoded
value until this commit.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
, the clock output setting for the AR803x driver is removed from being
hardcoded in the PHY driver and should be passed via device tree instead.
Update the device tree with the "qca,clk-out-frequency" property so that
Ethernet can work again.
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Soeren Moch <smoch@web.de>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
XDP - Xilinx Drone Platform is a board for drones or other UAV.
Pinmux the SD card by default, and if the SD card detect line is high
(inactive) then pinmux the SD1 interface to EMIO instead. SD is placed on
extension card and shares connection with on board wife. That means that
when SD card is present in the board wifi can't be used.
There seems to be an issue with DDR access from PL at 2400MT/s, after
updating the PMU and ATF firmware this is causing extremely slow DDR
access. Reducing the DDR speed from 2400 to 2133 appears to solve that
issue, even though the hardware has proven to be 2400 capable.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change mini u-boot qspi spi-max-frequency to 108Mhz, make the
frequency similar to full u-boot qspi flash spi-max-frequency.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current aliases missed gpio0 node, and this node shoud be
aliased to gpio index 0 to align with i.MX8QXP. Otherwise, we
will get below message when running "gpio status" command, and
see the reason by "dm uclass".
=> gpio status
Device 'gpio@5d090000': seq 0 is in use by 'gpio@5d080000'
Device 'gpio@5d0a0000': seq 1 is in use by 'gpio@5d090000'
Device 'gpio@5d0b0000': seq 2 is in use by 'gpio@5d0a0000'
=> dm uclass
uclass 36: gpio
0 * gpio@5d080000 @ fbaefb90, seq 0, (req -1)
1 * gpio@5d090000 @ fbaefc70, seq 1, (req 0)
2 * gpio@5d0a0000 @ fbaefd50, seq 2, (req 1)
3 * gpio@5d0b0000 @ fbaefe30, seq 5, (req 2)
4 * gpio@5d0c0000 @ fbaeff10, seq 3, (req 3)
5 * gpio@5d0d0000 @ fbaefff0, seq 4, (req 4)
6 * gpio@5d0e0000 @ fbaf00d0, seq 6, (req 5)
7 * gpio@5d0f0000 @ fbaf01b0, seq 7, (req 6)
Signed-off-by: Ye Li <ye.li@nxp.com>
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Author: Vladimir Oltean <vladimir.oltean@nxp.com>
Date: Thu May 7 00:11:51 2020 +0200
phy: atheros: Explicitly disable RGMII delays
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Author: Vladimir Oltean <vladimir.oltean@nxp.com>
Date: Thu May 7 00:11:51 2020 +0200
phy: atheros: Explicitly disable RGMII delays
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix the phy-mode accordingly to fix the regression.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Sync the device tree with 5.8-rc1.
It basically contains the following extra kernel commit:
commit 86b08bd5b99480b79a25343f24c1b8c4ddcb5c09
Author: Russell King <rmk+kernel@armlinux.org.uk>
Date: Wed Apr 15 16:44:17 2020 +0100
ARM: dts: imx6-sr-som: add ethernet PHY configuration
Add ethernet PHY configuration ahead of removing the quirk that
configures the clocking mode for the PHY. The RGMII delay is
already set correctly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
, which passes the 'qca,clk-out-frequency' property and it is important
to specify the correct frequency generated by the AR8035.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far
unsupported, reinstate the old cd-gpios behavior until this handling
is fully implemented. This avoid potential issue for SDCard boot:
the card detect fails with floating gpio.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far
unsupported, reinstate the old cd-gpios behavior until this handling
is fully implemented. This permits the DHSOM to boot from SD again,
without this patch the card detect fails.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The PSCI nodes are currently not populated for the Tegra210 and Tegra186
devices. This prevents the PSCI driver from being able to identify the
PSCI method used by these devices and causes the probe of the PSCI
driver to fail.
Since commit 81ea00838c ("efi_loader: PSCI reset and shutdown") was
added, which moves the PSCI EFI system reset handler into the PSCI
driver, this has prevented the EFI system reset from working for
Tegra210 and Tegra186. Therefore, populating these nodes is necessary
to fix the EFI system reset for Tegra210 and Tegra186.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Copy all device tree files required for omap4 sdp4430 support from
mainline Linux.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add OP-TEE firmware node in stm32mp15 U-Boot DTSI. This node is
needed since commit [1] that changed U-Boot/stm32mp15 to detect
OP-TEE availability by probing the resource instead of relying on
U-Boot configuration. The software sequence implemented by [1] is
fine but U-Boot DTS/DTSI files were not updated accordingly since,
hence OP-TEE presence is never detected by U-Boot, preventing Linux
kernel from using OP-TEE resources.
For consistency and to synchronize stm32mp15 DTSI files (excluding
U-Boot specific DTSI files) with the Linux kernel ones, this change
also moves the OP-TEE reserved memory nodes from board generic DTSI
files to U-Boot specific board DTSI files.
Link: [1] commit 43df0a159d ("stm32mp1: dynamically detect op-tee presence")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change DT compatibility name to match change in driver's name.
Remove unused io_ds and fifo_mode fields from DT.
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
Commit e71b6f6622 ("i2c: designware_i2c: Rewrite timing calculation")
change the hcnt and lcnt timing calculation. New timing calculation is
based on calculation from Designware i2c databook.
After this new timing calculation, hcnt will have negative value
with i2c-scl-falling-time-ns 5000 that set in socfpga_cyclone5_socdk.dts.
This patch overwrite i2c-scl-falling-time-ns to 300ns (default SCL fall
time used in Designware i2c driver) for Uboot.
Before the fix:
=> i2c dev 0
Setting bus to 0
Failure changing bus number (-22)
After the fix:
=> i2c dev 0
Setting bus to 0
=> i2c probe
Valid chip addresses: 17 51 55 5B 5C 5E 66 68 70
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Convert the board to DM_ETH instead of legacy networking. This requires
a minor addition to the DT to satisfy the requirement for specifying a
PHY node. No functional change from board user perspective.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Accidentally submitted a patch with indentation not correct, let's fix it
by indenting wrong lines.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
So far the puma dts files only just included the main puma dtsi without
handling the actual baseboard and rk3399-puma.dtsi was very much
detached from the variant in the mainline Linux kernel.
Recent changes resulted in a strange situation with nonworking puma boards.
Commit ab800e5a6f ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi")
moved the sdram include from rk3399-puma-ddrX.dts to new files
rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though.
Commit 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
replaced the rk3399-puma.dtsi nearly completely, but in the kernel
it definitly depends on a baseboard dts to actually enable peripherals
like sd-slot, uarts, etc.
So to untagle this and bring the whole thing more in line with mainline
Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate
DDR-option devicetrees and instead replace them with a puma Kconfig option
to select and include the needed DDR variant.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tabs not spaces, so transform it to the common styling.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The regulator enable-gpio uses opposite values for the declaration
vs. the enable_active_low property, breaking the regulator enablement.
Make the usbhost-supply work again by bringing them in sync again.
This mimics the upstream Linux change found on:
http://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The gmac reset has opposite values for the gpio declaration
and the separate reset-active, bring this in line to make
u-boot also find the ethernet-phy.
This mimics the upstream Linux commit found on
https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The 'stdout-path' is missing after dts sync.
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.
Net - Dual ethernet port, 1 X Gbe, 1 X 100M
USB - USB 3.0
DC - USB-Type C, 5V 2A
Storage - TF card, eMMC
Just build idbloader.img and u-boot.itb for Rockpi E board and
follow the blow steps to replace the relevant partition.
dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc
Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl7YxFMcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyJnICACR6Q6OclfIuM0A3ubV
GV48+iVz55eZnrZFKkbALBNjwTsshLpdZ/7Lr4zPD5e/FmrbJ+RONd0B6E38fSJk
Rq1ZwMyuR6yv+LAb9+La36tGqD9bCFewqBpR5LQNOdjE+fG66rrWxksMME1jOIr5
FLpFkk3lmEUloQumHDCQUgzXC/TUWpedgxpT15l1nR/Ovkh/MPvggIdS2zMWw92J
oA9shaNTVLd//W9icduXagNtRMsjscmf/zTZFCYgBRjUZgiPW+HnitWg7jqbYIuY
AqmNBZIrC6OuZ7W447g1rMGwbwQ5T9vbydp6PpHVqPvTt3D8OZ9h1+Hwwie7u9O1
CPaV
=xLcT
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.07-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2020.07 cycle
This set includes just two small commits that fix a build warning and
add a missing serial node.
- Fix mmc of path after syncfrom kernel dts;
- Add dwc3 host support with DM for rk3399;
- Add usb2phy and typec phy for rockchip platform;
- Migrate board list doc to rockchip.rst;
- Add rk3399 Pinebook Pro board support;
- Update dram_init in board_init and add memory node in SPL;
Sync initial support for Pinebook Pro device tree from Linux 5.7-rc1.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Configure 'tcphy1' and 'usbdrd_dwc3_1' nodes to support USB3.0 host
for Rockchip RK3399 Evaluation Board.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add u-boot,spl-boot-order as sdhci and sdmmc for booting
from eMMC and SD card.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Linux v5.7-rc1 dts(i) sync has changed the sdmmc node from
dwmmc@fe320000 to mmc@fe320000 and this ofpath is being
used in rockchip spl bootdevice code.
So, update the ofpath with a new node name and prefix "same-as-spl"
to missing u-boot,spl-boot-order.
Bug log:
U-Boot SPL 2020.07-rc2-00256-g9c5fef5774 (May 24 2020 - 20:20:43 +0530)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux"
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The khadas-vim, khadas-vim2, libretech-ac & libretech-*-pc boards were missing
DT tweak to enable USB gadget.
Add them to their -u-boot.dtsi files and include the right gxl-u-boot.dtsi.
Fixes: a19e8a0f03 ("arm: dts: meson-gxl: Add USB Gadget nodes for U-Boot")
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Include the common g12 u-boot tweaks to permit enabling video output tweaks
on Khadas VIM3 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Disable SDR104 mode until we know it is really stable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The I2C2 uses different pinmux on AV96, use correct pinmux and
also add comments about the I2C being present on the "low-speed"
expansion connector X6.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add another mux option for I2C2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The SPI NOR nWP line is connected to GPIO PF7 on the SoM,
pull the GPIO line high by default to clear SPI NOR WP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier
implementation of new CRS3xx series boards, based on Marvell Prestera
98DX3236.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Commit f49ac7e1c4 switched the default PHY speed to 3.125Gbit to resolve
issues with SFP modules. However, U-Boot does not have a "2500base-x"
phy-mode.
Resolve this by using "sgmii-2500" instead.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Without this U-Boot-specific property, booting on the Synology DS414
(or DS214+) fails in SPL. The spi0 DT node is not scanned, as a result
the SPI flash cannot be found.
Signed-off-by: Ezra Buehler <ezra@easyb.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
- Enable DM_ETH on omap3_logic board
- Enable Caches in SPL for K3 platforms
- Enable backup boot mode support for J721E
- Update the DDR timings for AM654 EVM
- Add automated tests for RX-51
Use the same approach as ROC-RK3328-CC which enables SPL GPIO,
pinctl and regulator support. This allows the gen3 board to
boot through SPL and does not break gen2 in the process.
Signed-off-by: Kurt Miller <kurt@intricatesoftware.com>
Acked-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
adapting commit fa2047c473 ("rockchip: rk3328: enable spl-fifo-mode
for emmc and sdmmc") for rk3399.
Since mmc to sram can't do dma, add patch to prevent aborts transferring
TF-A parts.
Signed-off-by: Deepak Das <deepakdas.linux@gmail.com>
Enable DDR52 modes, since the SD core supports correct switching now.
For completeness, list HS200 modes, however those were already enabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reserve 4 kiB of space in R-Car Gen3 DTs when those DTs are compiled
to permit patching in OpTee-OS /firmware node, /reserved-memory node
and possibly also additional /memory@ nodes.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
With the converstion of SMC911x to DM, this can facilitate the omap3
boards from LogicPD (now called Beacon EmbeddedWorks) to be converted.
There isn't a clean solution to doing this in phases, so the boards are
all being done together to avoid breaking functionality.
Because the GPMC bus hasn't been converted, the -u-boot.dtsi node needs
to show the address of the ethernet controller for each board.
The board file, which is common betwen the OMAP35 and DM37 SOM LV and
Torpedo boards, can remove the manual ethernet initialization, but it
still needs to register the address and GPMC configuration for the Ethernet
controller which is now being moved around to board_late_init().
Lastly, this patch updates the various config files to add the reference
for DM_ETH and remove the SMC address, which is now fetched from the
newly created device tree nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
EMIF tool for AM65x [1] is now updated from rev 1.98 to 2.02
This update includes
* Optimizations in IO configuration.
* Fix for byte enablement in GCR registers.
* Fixes for PG2.0 including ZQ control.
[1]: http://www.ti.com/lit/zip/sprcah7
Acked-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used.
The fsl-ls2080a-qds DTS will be used by default if there isn't a DTS
file specifically made for the current SERDES protocol.
This patch adds the necessary DPMAC nodes (DPMAC 1-8) for
protocol 42 (0x2A) on SD#1.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used. The fsl-ls2088a-qds DTS will be used by default if
there isn't a DTS file specifically made for the current SERDES
protocol.
This patch adds support for the on-board ports (DPMAC 1,2 and 4,5) found
on the SERDES protocols 21(0x15) and 29(0x1d) for SD#1.
On the LS1088AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as 2 input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.
Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 2 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add device trees describing possible uses of mezzanine cards depending
on the SERDES protocol employed.
This patch adds DPAA2 networking support for the following protocols on
each SERDES block:
* SD #1: 3, 7, 19, 20
* SD #2: 11
Each SERDES block has a different device tree file per protocol
supported, where the IO SLOTs used are enabled and PHYs located on the
mezzanine cards are described. Also, dpmac nodes are edited and their
associated phy-connection-type and phy-handle are added.
Top DTS files are also added for each combination of protocol on the 3
SERDES blocks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The LX2160A processor has two external MDIO interfaces, described in the
DTS as emdio1 and emdio2.
On the LX2160AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as eight input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.
Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 8 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.
Also, DPMAC 17 and 18 are updated to reference the on-board PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add nodes for DPMACs 1, 2 and 5-6 which were missing from the
description. These will be later used on the LX2160AQDS specific DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to new qspi driver, some properties like "bus-num, num-cs,
big-endian" are no longer used. Device endiannes can be determined from
device-type data in driver.
Now use board specific compatibles, generic node names and specific
labels to align with linux device-tree properties.
Also consolidate spi-max-frequency to 50Mhz treewide.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds support for uart4 to the
processor level device tree include file.
Signed-off-by: Tiaki Rice <tiakirice@hotmail.com>
Cc: Eugen Hristev <Eugen.Hristev@microchip.com>
A defconfig is added on lx2160ardb which allows UEFI variable management
via OP-TEE. Enable the the node in the relevant DTS file.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl69FWMACgkQ4rK92eCq
k3Vy9wgAmFLZ+u2C87A9Cs8i73QX/hs9TsjTJJPxsQWy3bOILgw8ZqBtzqD0qPvc
Mpqq7UEIZ17OW/lZCi3hqC0nGj7bT3N9rDpUQfu5Voq3GoO80yZqvCQU04AXGGpW
Aj0fjI5a6JRxQfR7XVoNw7UXPDUrDlchvBDR1GMK4cj4Sw/B+pXNDjkoJ1UWbxG6
INDgQQKhOCdMzbIsMLiUe4zkT6E8ADI0eJzgti3kWBzrdkwXZg40iEJu/MbMPRKE
Y22QZ6EkEMFTVYeCPXLU8keo4UbBIKDXWmVDbDeDbNa0QrKZ2IZ0TijajWeMWxZV
Q9J7JgpSchWcVB14vYNx+HXPUHANTA==
=bhlu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200514' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp1: migrate MTD and DFU configuration in Kconfig
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
- sync RPi4's env size with other RPi configs
- add kconfig option to reserver more pages in the EFI mem map
- add support for SDMA which is used by RPi4
- fix corner case boot bug for RPi3 32-bit
-----BEGIN PGP SIGNATURE-----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=66oV
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- fix phy configuration for RPi4's bcmgenet
- sync RPi4's env size with other RPi configs
- add kconfig option to reserver more pages in the EFI mem map
- add support for SDMA which is used by RPi4
- fix corner case boot bug for RPi3 32-bit
DT alignment with Linux 5.7-rc2, including the kernel commits
431c89e6f323 ARM: dts: stm32: use correct vqmmc regu for eMMC on stm32mp1 ED1/EV1 boards
79e965053872 ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
877db62ea516 ARM: dts: stm32: add cd-gpios properties for SD-cards on STM32MP1 boards
7519e95ba5f8 ARM: dts: stm32: Do clean up in stmpic nodes on stm32mp15 boards
f68e2dbc591a ARM: dts: stm32: Rename stmfx joystick pins on stm32mp157c-ev1
d6210da4f8bf ARM: dts: stm32: add cpu clock-frequency property on stm32mp15x
b65b6fc56925 ARM: dts: stm32: add wakeup-source in all I2C nodes of stm32mp157c
1c1cf5996cfb ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp157c-ed1
bef15fc0fad9 ARM: dts: stm32: add i2c2/i2c5 sleep pinctrl on stm32mp157c-ev1
b7fc0a87b9ac ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp15xx-dkx
a5e557655285 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp15 DK boards
8bc631b650a6 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp157c-ed1
fccd6a577bb3 ARM: dts: stm32: Correct stmfx node name on stm32mp157c-ev1 board
cc775a83db65 ARM: dts: stm32: add resets property on all DMA nodes on stm32mp151
c5fae093511b ARM: dts: stm32: enable USB OTG Dual Role on stm32mp157c-ev1
9879e2165758 ARM: dts: stm32: add USB OTG pinctrl to stm32mp15
82ac8a81f985 ARM: dts: stm32: add USB OTG full support on stm32mp151
8714b26e2863 ARM: dts: stm32: remove useless properties in stm32mp157a-avenger96 stmpic node
a7959919709e ARM: dts: stm32: Add UART8 pins A pinmux entry on stm32mp1
4d7c53a684da ARM: dts: stm32: Add USART3 pins A pinmux entry on stm32mp1
80ab128332ee ARM: dts: stm32: Add SAI2A pins B pinmux entry on stm32mp1
ab7f98c0c546 ARM: dts: stm32: Add Ethernet0 RMII pins A pinmux entry on stm32mp1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The SPI NOR nWP line is connected to GPIO PF7 on the SoM,
pull the GPIO line high by default to clear SPI NOR WP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add custom DDR DRAM settings for the DHCOR and DHCOM SoMs and put them
into use by the board file instead of the default ones. These new DRAM
settings are a better fit for the SoMs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The commit 132e5b6898 ("ARM: dts: stm32: Split AV96 into DHCOR SoM
and AV96 board") was not applied correctly and in full, and omitted
an important split of the SoM into 3V3 and 1V8 options. The Avenger96
board is based on the 1V8 IO option of the DHCOR SoM, however this is
an optional modification of the 3V3 IO DHCOR SoM with extra on-SoM
regulator to cater for the 96boards 1V8 IO requirements.
Reinstate the split between the 1V8 and 3V3 IO variants.
Fixes: 132e5b6898 ("ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the DDR3 dtsi files generated by STM32CubeMX 5.6.0
Speed Bin Grade = using DDR3-1066G / 8-8-8 and all others
parameters at default value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Force boot-led ON and no more rely on default-state.
This patch avoid device-tree modification for U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add reserve memory for OP-TEE in U-Boot and in kernel device tree:
- no more reduce the DDR size in "memory" node:
CONFIG_SYS_MEM_TOP_HIDE is no more used
- U-Boot device-tree defines the needed "reserved-memory" for OP-TEE
and U-Boot should not use this reserved memory: board_get_usable_ram_top
use lmb lib to found the first free region, the not reserved
memory, enough to relocate U-Boot: the needed size of U-Boot
is estimated with gd->mon_len + CONFIG_SYS_MALLOC_LEN.
- the optee node ("optee@...": firmware with compatible "linaro,optee-tz")
and the associated "reserved-memory" are deactivated in kernel device
tree when OP-TEE is not detected by U-Boot to prevent kernel issue
(memory is reserved but not used, optee driver probe failed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The DHCOR board does exist in multiple variants with different DDR3
DRAM sizes. To cater for all of them, implement DDR3 code handling.
There are two GPIOs which code the DRAM size populated on the SoM,
read them out and use the value to pick the correct DDR3 config.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Adjust the DDR configuration dtsi such that they only generate the
DRAM configuration node, the DDR controller node is moved into the
stm32mp157-u-boot.dtsi itself. This permits including multiple DDR
configuration dtsi files in board DT.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
At present the pinctrl nodes are not enabled in pre-relocation U-Boot so
the UARTs do not correctly select the pinconfig to enable the UART pins.
Fix this so that the U-Boot banner is printed.
This fixes serial output on rpi_3b_32b with the following config.txt
options:
enable_uart=1
gpu_freq=250
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 9821636b64 (bcm2835_pinctrl: Probe pre-reloc)
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Enable the second USB controller, which is connected to a hub with 4
ports. The first controller is for the OTG port and is currently not
supported.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
[narmstrong: removed useless DWC2_UTMI_WIDTH in meson64.h]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We are currently using SC_R_LAST as a marker for imx8 power domain tree
nodes without a resource attached. This value is compiled into dtb as
part of the linux build and used by uboot.
The SC_R_LAST constant changes frequently as SCFW resources are added
(by design) and every time we need to update linux and uboot headers
together or boot can fail.
Fix this by replacing SC_R_LAST usage with a new constant SC_R_NONE
defined to be 0xFFF0.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.
It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
This resolves issues with certain SFP modules.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Add initial support for Google's Coral Dev Board based on i.MX8MQ.
https://coral.ai/products/dev-board
The Phanbell naming has been used here to match the naming convention
used in Google's U-Boot source tree:
https://coral.googlesource.com/uboot-imx/
Co-developed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Marco Franchi <marcofrk@gmail.com>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch synchronizes the device tree with that from 5.6.7.
This also adds nodes for crypto and ddrc, which makes keeping
the device tree files from individual boards in sync with the
Linux kernel. This is helpful when boads reference those nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
commit b2f5da9dd0 ("rockchip: rk3399: Add Nanopi M4 board support") added
support for Nanopi M4 board with Dual-Channel 4GB LPDDR3-1866 RAM.
This patch adds another variant of NanoPi M4 board with Dual-Channel
2GB DDR3-1866 RAM.
Signed-off-by: Deepak Das <deepakdas.linux@gmail.com>
Add Firefly ROC-RK3399-PC Mezzanine board which is an
extension board on top of roc-rk3399-pc.
Will drop the separate defconfig file, once we support
the board detection at runtime.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399 dts(i) files from v5.7-rc1 linux-next.
Reason:
To get updated PCIe nodes and properties on respective
dts(i) files.
Summary:
- sync won't include new board dts(i)
- sync will add required files used on respective dts(i)
- rk3399-puma-u-boot.dtsi spiflash label changed to norflash
- move puma.dtsi bios_enable into rk3399-puma-u-boot.dtsi
- move legacy max-frequency of sdhci into rk3399-u-boot.dtsi
- update cross-ec-[keyboard|sbs].dtsi path as per U-Boot
- keep roc-rk3399-pc dc_12v changes to -u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move U-Boot specific properties into rk3399-evb u-boot
specific dtsi file.
This would help to sync the devicetrees from Linux whenever
required instead of adding specific nodes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move U-Boot specific properties into rk3399-puma u-boot
specific dtsi file.
This would help to sync the devicetrees from Linux whenever
required instead of adding specific nodes.
Cc: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
If the VBUS regulator is always-on, XHCI will fail to detect USB 3.0
devices; USB 2.0 devices will work however.
Make the VBUS regulator controllable and tie it to only the XHCI. This
makes all three USB ports usable.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROC-RK3328-CC from Firefly and Libre Computer Project is a credit
card size development board based on the Rockchip RK3328 SoC, with:
- 1/2/4 GB DDR4 DRAM
- eMMC connector for optional module
- micro SD card slot
- 1 x USB 3.0 host port
- 2 x USB 2.0 host port
- 1 x USB 2.0 OTG port
- HDMI video output
- TRRS connector with audio and composite video output
- gigabit Ethernet
- consumer IR receiver
- debug UART pins
The ROC-RK3328-CC has the enable pin of the SD card power switch tied
to GPIO_0_D6. This pin also has the function SDMMC0_PWREN, which is
muxed by default. SDMMC0_PWREN is an active high signal controlled by
the MMC controller, however the switch enable is active low, and
pulled low (enabled) by default to make things work on boot.
As such, we need to mux away from SDMMC0_PWREN and use GPIO to enable
power to the card. The default GPIO state for the pin is pull-down and
input, which doesn't require extra configuration when paired with the
external pull-down and active low switch.
Deal with this by enabling regulator support in SPL, and setting
"u-boot,dm-spl" for the regulator and other device nodes needed for
muxing the pin.
The device tree file is synced from the Linux kernel next-20200324.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This syncs rk3328 device tree files from the Linux kernel next-20200324.
The last commit to touch these files is:
b2411befed60 ("arm64: dts: add bus to rockchip amba nodenames")
Additional changes not yet in the Linux kernel include:
arm64: dts: rockchip: rk3328: drop #address-cells, #size-cells from grf node
arm64: dts: rockchip: rk3328: drop non-existent gmac2phy pinmux options
arm64: dts: rockchip: rk3328: Replace RK805 PMIC node name with "pmic"
Changes include:
- conversion of raw pin numbers to macros
- removal of deprecated RK_FUNC_* macros
- update of device tree binding headers
- new devices
- device tree cleanups
- gmac2phy disabled in -u-boot.dtsi as it is not supported in U-boot
This includes a re-ordering of the USB device nodes compared to upstream
Linux, moving the dwc2 OTG controller after the EHCI/OHCI nodes. This is
currently required as otherwise the dwc2 controller would not be able to
detect devices in some cases. This may be due to lack of USB PHY support
in U-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The "hnp-srp-disable" property for dwc2 is specific to U-boot, not part
of upstream Linux's device tree bindings.
Move it to rk3328-u-boot.dtsi to avoid losing it when syncing device
tree files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree file for rk3328-evb in the Linux kernel does not have
gmac2io enabled. Instead, gmac2phy is enabled, but that is not supported
in U-boot.
Move the gmac2io related nodes to rk3328-evb-u-boot.dtsi to preserve the
current functionality. When the device tree files are synced, gmac2phy
should be marked as "broken" in -u-boot.dtsi files.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
USB 3.0 is only supported in U-boot, not in the Linux kernel where the
device tree files are ultimately synced from. While the xhci node was
moved, the external vbus regulator was not.
Move it as well.
Fixes: 2e91e2025c ("rockchip: rk3328: migrate u-boot node to -u-boot.dtsi")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
Introduce the QorIQ DPAA 1 Frame Manager nodes in the LS1046ARDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
LS1046A SoC. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the LS1043ARDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
LS1043A SoC. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA Frame Manager v3 device tree nodes description.
The device tree fragments are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Rename fsl-ls1028a-qds.dts to fsl-ls1028a-qds.dtsi so that
it can be used as common device tree for lpuart and duart.
Add lpuart device tree and duart device tree respectively
for qds which are used with duart and lpuart console.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the external MDIO nodes and describe the PHYs (8 x
VSC8514, AQR105). Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the external MDIO nodes and describe the PHYs (4 x AQR405
and 4 x CS4340). Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the EMDIO1 node and describe the 2 AR8035 RGMII PHYs and
the 2 AQR107 PHYs. Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the External MDIO1 device node found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the External MDIO1 device node found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the External MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add rng node in rk3399-u-boot.dtsi and enable it in
rk3399-evb-u-boot.dtsi.
Signed-off-by: Lin Jinhan <troy.lin@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove DT nodes which are not used by U-Boot, like audio and video in/out
nodes. This saves about 35 kiB on the resulting U-Boot binary without any
impact on functionality.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen3 device trees with Linux 5.6.2,
commit 9fbe5c87eaa9b72db08425c52c373eb5f6537a0a .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen2 device trees with Linux 5.6.2,
commit 9fbe5c87eaa9b72db08425c52c373eb5f6537a0a .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The file <board name>-u-boot.dtsi inculde automatically by the build
system, no need to add this to dts file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
roc-rk3399-pc has an FE1.1 USB 2.0 HUB which connects two USB ports
(HOST1 and HOST2). For end devices to work we need to enable USB hub
so that HOST detects there presence and enumerates them accordingly.
This requires explicit pinctrl within gpio enablement.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the SPI flash controller and reduce the usable eMMC data pins to 4
to permit using the on-board SPI NOR Flash.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Activate the on-board SPI NOR Flash by enabling the SPI controller and
disabling the DS eMMC pin in the VIM2 u-boot.dtsi file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add memory-controller@e000e000 node in zynq-ces-nand.dts as
zynq_nand driver utilizes flash@e1000000 node. Without this
dt node mini nand u-boot does not probe.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Do not use irps54012 as device node which is not correct.
- Fix addresses of irps5401/u180 on zcu104 revisions.
- Remove clock-cells property. It is PMIC without any clock output.
- Define irps5401 nodes in zynqmp-e-a2197
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add label to GPIO lines controlling boot mode and POR EMIO pins so System
Controller can assert those lines on Versal.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Cubieboard is a single board computer containing a
Actions S700 SoC(with 4 ARMv8 Cortex-A53 cores).
This patch adds respective defconfig alongwith .dts(copied
from Linux v5.5-rc6 with hash "b3a987b0264d").
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Devices like uart and clk are needed to be enabled before relocation.
this patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds .dtsi file(sync with Linux 5.5-rc6 with hash "b3a987b0264d")
and required binding for S700 SoC that is a 64-bit Quad-core ARM
Cortex-A53 cores.
It also provisions dts file to be built based on selected
platform(CONFIG_MACH_S900/S700).
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Devices like uart and clk are needed to be enabled before relocation.
This patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Synchronize device tree bindings with v5.5-rc6 tag with commit id
"b3a987b0264d".
Also, it removes older clock binding defined for S900 along with undocumented
compatible string "actions,s900-serial" from serial driver and adapts clock
driver to cater to new bindings.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
The AV96 is in fact an assembly of DH Electronics DHCOR SoM on top
of an AV96 reference board. Split the DTs to reflect that and make
sure to DHCOR SoM can be reused on other boards easily.
It is also highly recommended to configure the board for the DHCOM
make stm32mp15_dhcom_basic_defconfig
make DEVICE_TREE=stm32mp15xx-dhcor-avenger96
as that permits reusing the board code for the DH components, like
accessing and reading out the ethernet MAC from EEPROM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: I7db47280d4eb0d668eb4e006355240271154f97f
The PLL4 is supplying SDMMC12, SDMMC3 and SPDIF with 120 MHz and
FDCAN with 96 MHz. This isn't good for the SDMMC interfaces, which
can not easily divide the clock down to e.g. 50 MHz for high speed
SD and eMMC devices, so those devices end up running at 30 MHz as
that is 120 MHz / 4. Adjust the PLL4 settings such that both PLL4P
and PLL4R run at 100 MHz instead, which is easy to divide to 50MHz
for optimal operation of both SD and eMMC, SPDIF clock are not that
much slower and FDCAN is also unaffected.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove the unnecessary file stm32mp157-pinctrl.dtsi and
solve all issues introduced by the commit 8914831860 ("Merge branch
'next'") after a conflict on the patch applied in the next branch in
commit 1a4f57c895 ("ARM: dts: stm32mp1: DT alignment with Linux 5.6-rc1")
Need to reapplied on stm32mp15-pinctrl.dtsi the the 3 patches
applied previously on file "stm32mp157-pinctrl.dtsi" in v2020.04
- commit 4fdbe6487d ("ARM: dts: stm32: Add alternate pinmux for SDMMC1
direction pins")'
- commit 5fdcba6402 ("ARM: dts: stm32: Add alternate pinmux for SDMMC2
pins 4-7")'
- commit 955de51111 ("ARM: dts: stm32: Add alternate pinmux for ethernet
RGMII")'
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Further cleanups for 'make refcheckdocs'
- Another BTRFS fix.
- Support for automatic decompression of images with booti as well as
unlz4 command for manual decompression.
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
-----BEGIN PGP SIGNATURE-----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=1Ffl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200420' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- enable DM_RNG on meson boards
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
- Fix boot on am335x guardian board
- Increase OPSI speed on AM65x and J721E devices
- Use JTAD register for identifying K3 devices.
- Update TI entry in MAINTAINERS file.
Add the USB DWC2 node to u-boot specific dtsi files since Gadget
support is not (yet) available in upstream Linux yet.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Those two boards are supposed to be run with a single u-boot binary.
There are notable differences though - HSC uses DSA switch (which
phy_id == 0x0) and DCC (DP83848C).
After the commit 3bf135b6c3
("drivers: net: phy: Ignore PHY ID 0 during PHY probing") the PHY devices
with phy_id == 0 are not created in U-Boot anymore. This caused regression
on HSC.
To fix this problem - the fec's 'fixed-link' node has been introduced and
the phy_id is not assessed anymore. This approach works on both boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
During the conversion of this board to DM_REGULATOR, usb-mass-storage
was broken and started failing with the following error:
=> ums 0 mmc 2
UMS: LUN 0, dev 2, hwpart 0, sector 0x0, count 0xe90000
Error enabling VBUS supply
g_dnl_register: failed!, error: -38
g_dnl_register failed
Fix this by adding the relevant GPIO to the regulator node.
Fixes: 4ca99fe81a ("ARM: imx: dh-imx6: Enable DM regulator")
Signed-off-by: Harald Seiler <hws@denx.de>
Use DM_ETH instead of legacy networking. Add VIO as a fixed regulator
to the relevant device-trees and augment the FEC node with properties
for the reset GPIO.
It should be noted that the relevant properties for the reset GPIO
already exist in the PHY node (reset-gpios, reset-delay-us,
reset-post-delay-us) but U-Boot currently ignores those and only
supports the bus-level reset properties in the FEC node
(phy-reset-gpios, phy-reset-duration, phy-reset-post-delay).
Signed-off-by: Harald Seiler <hws@denx.de>
The detection of the revD1 version is based on the presence of the PMIC.
Currently revb1 device trees are used for mx6q/mx6dl variants, which
do not have the PMIC nodes.
This causes revD1 boards to be incorrectly be detected as revB1.
Fix this issue by using the revd1 device trees, so that the PMIC node can be
found and then the PMIC can be detected by reading its register ID.
Imported the revd1 device trees from mainline kernel version 5.7-rc1.
Reported-by: Heiko Schocher <hs@denx.de>
Reported-by: Derek Atkins <derek@ihtfp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Derek Atkins <derek@ihtfp.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Linux doesn't provide skeleton.dtsi file so let's remove its include and
provide #address-cells/size-cells = <1> that were defined in
skeleton.dtsi before.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The device trees for TQMa6x SOM support variations in
- CPU type: imx6dl- or imx6q-
- MBa6 I2C bus access: -mba6a (i2c1) or -mba6b (i2c3)
(plus the respective common/module include trees)
- USBH1 is directly connected to a hub
- USBOTG is connected to a separate connector
and can act as host/device or full OTG port.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
The Linux VPU bindings have changed and dropped the dmc register range.
Add it back in the meson-gx-u-boot.dtsi file until a proper canvas driver
is available.
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The libretech-ac u-boot.dtsi file is missing to enabled DT nodes changes
to enable Video output on U-Boot.
Fixes: 671b1db8f8 ("arm64: dts: meson-gx: vpu should be probed before relocation")
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
The LED labels do not match the silkscreen on the board, fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add DT entries, Kconfig entries and board-specific entries to configure
FMC2 bus and make KS8851-16MLL on that bus accessible to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- Misc enhancements to Clearfog, including board variant detection
(Joel)
- Misc enhancements to Turris Mox, including generalization of the
ARMADA37xx DDR size detection (Marek)
Commit e8e9715df2 requires the USB3 regulator node to have the
enable-active-high property for the regulator to work properly. The
GPIO_ACTIVE_HIGH constant is not enough anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: e8e9715df2 ("regulator: fixed: Modify enable-active-high...")
Reviewed-by: Stefan Roese <sr@denx.de>
With recent changes to the mmc subsystem (chip detect code etc) update
the sdhci node of the Turris Mox device tree.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Using a consistent hardcoded MAC address from the DTS file causes
issues when using multiple devices on the same network segment.
Instead rely on environment configuration or random generation.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Sort the Armada series dts in the Makefile alphabetically
prior to adding new board support.
Signed-off-by: Josip Kelečić <josip.kelecic@sartura.hr>
Reviewed-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
In 1 bit mode OSPI can work at upto 50MHz, this provides better write
performance. Therefore increase frequency from 40MHz to 50MHz
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
In 1 bit mode OSPI can work at upto 50MHz, this provides better write
performance. Therefore increase frequency from 40MHz to 50MHz
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
- As there is a requirement to store certain data, we need a persistent
storage in u-boot. Hence, we need to save env in NAND
- Add default Guardian environment variables
- Update partition table:
- Reserve some space for experimentation, this ensures proper
backwards compatibility
- Update defconfig accordingly
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
This patch enables the guardian board to provide feedback
about the boot stage in headless mode. The on-board led
would behave in the following pattern
* U-boot -> GLOW LED
* Linux -> BLINK LED [HEART-BEAT PATTERN]
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Pull in changes that have been pending in our 'next' branch. This
includes:
- A large number of CI improvements including moving to gcc-9.2 for all
platforms.
- amlogic, xilinx, stm32, TI SoC updates
- USB and i2c subsystem updtaes
- Re-sync Kbuild/etc logic with v4.19 of the Linux kernel.
- RSA key handling improvements
Adding "u-boot,dm-pre-reloc" and enable CONFIG_SPL_CACHE
to enable cache driver in SPL.
This fixed error below in SPL:
cache controller driver NOT found!
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Update these 3 files from Linux:.
- socfpga_arria10.dtsi (Commit ID c1459a9d7e92)
- socfpga_arria10_socdk.dtsi (Commit ID d9b9f805ee2b)
- socfpga_arria10_socdk_sdmmc.dts (Commit ID 17808d445b6f)
Change in socfpga_arria10.dtsi:
- Add clkmgr label, so that can reference to it in u-boot.dtsi.
Change in socfpga_arria10-u-boot.dtsi:
- Add compatible and altr,sysmgr-syscon for uboot.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Move Uboot specific properties to *u-boot.dtsi files.
Preparation to sync Arria 10 device tree from Linux.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add and enable RTC-backed boot counter on ABB SECU1 platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
-----BEGIN PGP SIGNATURE-----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=PiOt
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200406' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic into next
- clk: meson-g12a: missing break
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
pd_dma_* nodes should be accessible during pre-relocation stage of
U-Boot proper for properly handling power domains.
This fixes the issue with permanent failing of invocation of
power_domain_get_by_index() in the common code of DM power domain
uclass (drivers/power/domain/power-domain-uclass.c).
Fixes: f0cc4eae9a ("core: device: use dev_power_domain_on")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
pd_dma_* nodes should be accessible during pre-relocation stage of
U-Boot proper for properly handling power domains.
This fixes the issue with permanent failing of invocation of
power_domain_get_by_index() in the common code of DM power domain
uclass (drivers/power/domain/power-domain-uclass.c).
Fixes: f0cc4eae9a ("core: device: use dev_power_domain_on")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
For non-SPL/TPL setups dm-spl, dm-tpl, dm-pre-proper, dm-pre-reloc are
handled equally, forcing the nodes with these properties
to be accessible and device being probed
before pre-relocation of U-Boot proper (drivers/core/util.c):
bool ofnode_pre_reloc(ofnode node)
{
/* for SPL and TPL the remaining nodes after the fdtgrep 1st pass
* had property dm-pre-reloc or u-boot,dm-spl/tpl.
* They are removed in final dtb (fdtgrep 2nd pass)
*/
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-reloc"))
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-proper"))
return true;
/*
* In regular builds individual spl and tpl handling both
* count as handled pre-relocation for later second init.
*/
if (ofnode_read_bool(node, "u-boot,dm-spl") ||
ofnode_read_bool(node, "u-boot,dm-tpl"))
return true;
return false;
}
Howewer, to avoid confusion in future, replace dm-spl
`%s/dm-spl/dm-pre-proper/g` properties to dm-pre-proper
to explicitly state that they are handled during pre-relocation
stage of U-Boot proper.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
For non-SPL/TPL setups dm-spl, dm-tpl, dm-pre-proper, dm-pre-reloc are
handled equally, forcing the nodes with these properties
to be accessible and device being probed
before pre-relocation of U-Boot proper (drivers/core/util.c):
bool ofnode_pre_reloc(ofnode node)
{
/* for SPL and TPL the remaining nodes after the fdtgrep 1st pass
* had property dm-pre-reloc or u-boot,dm-spl/tpl.
* They are removed in final dtb (fdtgrep 2nd pass)
*/
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-reloc"))
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-proper"))
return true;
/*
* In regular builds individual spl and tpl handling both
* count as handled pre-relocation for later second init.
*/
if (ofnode_read_bool(node, "u-boot,dm-spl") ||
ofnode_read_bool(node, "u-boot,dm-tpl"))
return true;
return false;
}
Howewer, to avoid confusion in future, replace dm-spl
`%s/dm-spl/dm-pre-proper/g` properties to dm-pre-proper
to explicitly state that they are handled during pre-relocation
stage of U-Boot proper.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
With multi defconfig NOR flash information about NOR should be taken from
DT that's why there is no reason to specify address and sizes via fixed
config.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no real need to include full DT when only some nodes are enough to
use. It will save some space.
Retested with FSBL for initial SoC setup. SPL didn't work.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Instead of symlink include origin file and just change model description.
Difference is not in DT but in ps7_init configurations which is taken based
on device tree name that's why the same DT can't be used.
Also update model and update comments to match configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pinctrl is handled via firmare interface that's why move it there without
reg property and new compatible string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtbs_check is showing warning around GIC compatible property as
interrupt-controller@f9010000: compatible: ['arm,gic-400', 'arm,cortex-a15-gic']
is not valid under any of the given schemas
Similar change has been done also by Linux kernel commit 5400cdc1410b
("ARM: dts: sunxi: Fix GIC compatible")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Node name should be <name>@<address> which is not how partitions are
described.
Issue was found by running dtbs_check as:
flash@0: 'partition@qspi-device-tree', 'partition@qspi-fsbl-uboot',
'partition@qspi-linux', 'partition@qspi-rootfs'
do not match any of the regexes: ...
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sync DP subsystem with the latest state in Xilinx U-Boot repository.
This binding hasn't been approved in mainline Linux but it is much better
than ancient version which this patch removes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In kernel 5.4, support has been added for reading MTD devices via
the nvmem API.
For this the mtd devices are registered as read-only NVMEM providers
under sysfs with the same name as the flash partition label property.
So if flash partition label property of multiple flash devices are identical
then the second mtd device fails to get registered as a NVMEM provider.
This patch fixes the issue by having different label property for different
flashes.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add clock-cells and clock-output-names for sdhci0 and sdhci1.
These are needed for linux sdhci driver from 5.4 version onwards.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reset controller is handled via firmware that's why it should be the part
of firmware node. Origin solution hasn't been removed when above change was
applied by commit b07e97b4ba ("arm64: zynqmp: Use reset header in
zynqmp.dtsi").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify dts files to add 'no-1-8-v' property for all the ZynqMP boards.
User can remove this property to enable the UHS mode. This is to keep
the same speed (HS) modes across all the stages of the Linux Boot. Due
to power cycling limitation of some of the ZynqMP boards, some SD cards
don't get power cycled and are failing in Linux.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Sync zynqmp fpga manager with mainline.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
None name address should be aligned with address. DTC 1.5.1 is reporting
issues related to that.
arch/arm/boot/dts/zynq-zc770-xm010.dts:106.10-119.4: Warning
(spi_bus_reg): /amba/spi@e0007000/flash@0: SPI bus unit address format
error, expected "1"
arch/arm/boot/dts/zynq-zc770-xm013.dts:101.19-109.4: Warning
(spi_bus_reg): /amba/spi@e0006000/eeprom@0: SPI bus unit address format
error, expected "2"
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The same change has been done for Zynq by commit 1241c72b6db1
("ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property")
in mainline Linux kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.
Replace the legacy properties with the unified "wakeup-source"
property introduced in the Linux kernel commit 700a38b27eef
("Input: gpio_keys - switch to using generic device properties")
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dtc has new checks for I2C and SPI buses.
Fix the warnings in node names and unit-addresses.
Warning from Linux kernel:
arch/arm/boot/dts/zynq-zc702.dts:187.13-190.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@52: I2C bus unit address format error, expected "34"
arch/arm/boot/dts/zynq-zc702.dts:191.13-194.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@53: I2C bus unit address format error, expected "35"
arch/arm/boot/dts/zynq-zc702.dts:195.13-198.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@54: I2C bus unit address format error, expected "36"
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the Amlogic based libretech-pc platform.
This platform comes with 2 variant, based on the s905d or s912 SoC.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: update board/amlogic/q200/MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the libretech-pc device tree from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2")
The only exception to this is the mmc pinctrl pin bias of gxl SoC family.
This is a fix which found its way to u-boot but not Linux yet.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The card-detect GPIO and any other GPIO access currently doesn't work in
U-Boot SPL on any STM32 platform and crashes the SPL. To work around this
problem on AV96 right before release, remove the cd-gpios from DT. This
patch must be reverted right after release, once the proper fix for the
GPIO driver, "gpio: stm32: support gpio ops in SPL", is applied.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
This adds to the DT the I2C controllers that connect to the board ID EEPROM,
etc. With this change, you can now probe all I2C devices on a TX1 board.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
compatibility with stm32mp15_dhcom_basic_defconfig
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl6EiK0ACgkQ4rK92eCq
k3V6DggAhU7jE5MGs9A7En+YpANXbJ4tl56IZIjdzPzEjA2G3yuBv/DLci/w27aF
eaP83ayI/ZrVtevEBFomP0JRrzQc9r/ot+USVugGsoAigLbzJc5uba42FGn09Olh
uKkst0Fb7uPRzZQNwRc7hTKVSLvT11c0oPQyhhJM2djPDTETDry+RPnEFQ41SEUt
bNILmj0VRzikzbe5RXFWWYMUWBrt22pG2LLhog+WSRSpqrWM2zES64NnwAXxD/mR
YIQFZIZ6eWW2Otp+qzenkg5ZWIMVWRyUBAP5e0auKRE8TGWAXgBcoFRTRLf7oA/P
yr3TTBMWiPdqdXNe3MYzAiTpm7jrtg==
=RALH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200401' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Fix device tree of Avenger96 board from Arrow Electronics and add
compatibility with stm32mp15_dhcom_basic_defconfig
The core and vdd PMIC buck regulators were misconfigured, which caused
instability of the board and malfunction of high-speed interfaces, like
the RGMII. Configure the PMIC correctly to repair these problems. Also,
model the missing Enpirion EP53A8LQI on the DHCOR SoM as a fixed regulator.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The AV96 RGMII uses different pinmux for ETH_RGMII_TXD0, ETH_RGMII_RXD2
and ETH_RGMII_TX_CTL. Use the correct pinmux to make ethernet operational.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for DWMAC RGMII, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The board has an EEPROM on the same I2C bus as PMIC, at address 0x53.
The EEPROM contains the board MAC address.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: I340a0675c11e4599968b2e3ef0515fb8da8d7b42
Use DT /aliases node to establish a stable phandle to the configuration
EEPROM. This permits the configuration EEPROM to be moved e.g. to a
different address or a different bus. Adjust the board code to handle
new phandle lookup.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The DH Electronics DHCOR SOM has QSPI NOR on the SoM itself, add it
into the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Ia7c454c496f50e3fc4851ec1154f3641c416e98e
The eMMC uses different pinmux for the top four data lines, use such
a pinmux, otherwise it takes a very long time until the test for 8bit
operation times out. And this is the correct pinmux per schematic too.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for SDMMC2 pins 4..7, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The SD uses different pinmux for the D123DIRline, use such a pinmux,
otherwise there is a pinmux collision on the AV96. Add missing SD
voltage regulator switch and enable SDR104 operation.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for SDMMC1 direction pins, in particular
SDMMC1_D123DIR, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The sdmmc1_dir_pins_a: sdmmc1-dir-0 layout changed in commit 35a54d41d9
("ARM: dts: stm32mp1: sync device tree with v5.2-rc4") such that pins{};
became pins1{};pins2{};, however the SPL extras were not updated to reflect
that change. Fix this.
This fixes booting from SD1 X9 slot on the AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Fixes: 35a54d41d9 ("ARM: dts: stm32mp1: sync device tree with v5.2-rc4")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Configure RX and TX bus-width values to use flexspi in octal I/O mode.
If bus-widths are not specified, then single I/O mode is set by default.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Configure RX and TX bus-width values to use flexspi in octal I/O mode.
If bus-widths are not specified, then single I/O mode is set by default.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a-qds has 2 micron "mt35xu512aba" flashes of size 64M each
connected on A0 and B1 i.e on CS0 and CS3. Since flashes are connected
on different buses, only one flash can be probed at a time.
Add fspi node properties aligned with LX2160A-RDB fspi properties.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add IIC3 node from mainline Linux DT. This will be further updated in
subsequent DT sync, however adding this node for now is sufficient and
minimal change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since commit 79030a4861 ("rockchip: Add Single boot image
(with binman, pad_cat)") the following boot regression is seen:
U-Boot 2020.04-rc3-00050-gd16e18ca6c-dirty (Mar 09 2020 - 11:40:07 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
initcall sequence 67fd12a0 failed at call 6000b927 (err=-22)
This happens because the above commit missed to include the
"rockchip-u-boot.dtsi" for rv1108, so include this file
like it done for other Rockchip SoC dtsi's.
Fixes: 79030a4861 ("rockchip: Add Single boot image (with binman, pad_cat)")
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to make the console pins more robust to noise, activate
the pullups and increase its drive strength.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This parameter "st,phy-cal" becomes optional and when it is
absent the built-in PHY calibration is done.
It is the case in the helper dtsi file "stm32mp15-ddr.dtsi"
except if DDR_PHY_CAL_SKIP is defined.
This patch also impact the ddr interactive mode
- the registers of the param 'phy.cal' are initialized to 0 when
"st,phy-cal" is not present in device tree (default behavior when
DDR_PHY_CAL_SKIP is not activated)
- the info 'cal' field can be use to change the calibration behavior
- cal=1 => use param phy.cal to initialize the PHY, built-in training
is skipped
- cal=0 => param phy.cal is absent, built-in training is used (default)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
This commit manages diversity for STM32M15x SOCs with:
- dedicated files to support all STM32MP15 SOCs family.
The differences between those SOCs are:
-STM32MP151 [1]: common file.
-STM32MP153 [2]: STM32MP151 + CANs + a second CortexA7-CPU.
-STM32MP157 [3]: STM32MP153 + DSI + GPU.
- new files to manage security diversity on STM32MP15x SOCs.
On STM32MP15xY, "Y" gives information:
-Y = A means no cryp IP and no secure boot.
-Y = C means cryp IP + secure boot.
- stm32mp157 pinctrl files to better manage package diversity.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the
driver reset the phy via dts description adding a reset duration of 10 ms
following atheros 8031's datasheet recommendation.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
The FEC in the i.MX8MM doesn't support this feature. So don't pretend one
can use it.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Let pinctrl configuration for eMMC node (usdhc1) also be
accessible in SPL.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Before DM_VIDEO conversion this board used 24bpp
display configuration, so use it again.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update the dummy clock names to use unique identifiers. Otherwise the
previous node just gets overwitten by the next one with the same name.
This fixes eMMC boot not working on J721e-evm.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
With the latest RIOT, there is a different otap delay value for each
speed mode. Add a new binding with every supported speed mode. Also
disable a given speed mode in the host caps if its corresponding
otap-del-sel is not present.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add the "u-boot,dm-pre-reloc" property to the "ti,tilcdc,panel"
compatible node. In this way the video-uclass module can allocate the
amount of memory needed to be assigned to the frame buffer.
For boards that support Linux the property is added to the *-u-boot.dtsi
file since it is a u-boot specific dt flag.
Ran building tests with CONFIG_AM335X_LCD enabled and disabled for the
following configurations:
- brxre1_defconfig --> success
- am335x_guardian_defconfig --> success
- am335x_evm_defconfig --> success
- da850evm_defconfig --> failure with CONFIG_AM335X_LCD enabled
Enabling CONFIG_AM335X_LCD in da850evm_defconfig causes building errors
even without applying the patch. The driver has never been enabled on the
da850 and must be adapted for this platform.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Felix Brack <fb@ltec.ch>
The ESM handling on J7 processor board requires routing the
MCU_SAFETY_ERROR signal to the PMIC on the board for critical safety
error handling. The PMIC itself should then reset the board based on
receiving it. Enable the support for the board by adding the esm
node in place.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Main domain ESM support is needed to configure main domain watchdogs
to generate ESM pin events by default. On J7 processor board these
propagate to the PMIC to generate a reset when watchdog expires.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add fs_loader node which will be needed for loading firmwares
from the boot media/filesystem.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The compatible string "i2c-eeprom" is U-Boot own compatible, which
has never been approved by the DT community. "u-boot,i2c-offset-len"
is also a U-Boot own hack.
Linux adds "atmel,*" as generic compatibles, and U-Boot also followed
it by commit d7e28918aa ("i2c_eeprom: Add reading support").
The U-Boot own hack is no longer needed. Just sync with Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Import the nodename changes I made in Linux for avoiding dt-schama
warnings. This follows the $nodename patterns in the dt-schema.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Sync rk3288-vyasa dts file from Linux.
This sync has changes required to work HDMI output on
Vyasa RK3288 board.
This sync excludes the io_domains node since it is not
available in rk3288.dtsi.
Changes like vcc50_hdmi, vdd10_lcd and ddc-i2c-bus are
not merged to Linux yet but wil resync later if any
further updates on this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There have been multiple peripherals added to the main px30 dtsi
in the Linux kernel since its addition to u-boot. So to make it easier
to sync board devicetrees, update the core dtsi from Linux.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move the U-Boot specific bits to a -u-boot.dtsi include so all the
u-boot.dtsi hierarchy is included.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's some bits in the U-Boot rk3399.dtsi that aren't yet in the
upstream Linux dtsi but are needed for early boot. This moves them
to the u-boot.dtsi to make it easier to sync the rest of rk3399.dtsi
with upstream.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The upstream linux kernel for the Rockchip 3399 SoC use usbdrd3 naming so move
the two remaining devices over to that for their device trees to make it
easier to sync with upstream DTs.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl5GcB0ACgkQ4rK92eCq
k3Wr9gf/dDPJi6UBhLDio/IVKDBddOEUN0Lwdr9W0upL+DrdvEOyNyMSEKuLccIE
UTd1NmNNwcvgDRaPvB5o3R7twWItTW0cYlmVkFSZ228aq6xdf/SElN2OUD6B9Gh+
8bi6oVLu41TNMYn4VYxsEftcT2megfH8s+SH/FlvR5ua1yCC1vyrytEQjPIbJAB2
sa90ewDyp5EYqGLdAk6AVjPLeNZsaleGwuyLf04PoC2xhn+3HTEKJCJN4O46aJUr
0GUI7YN7pTjIfZdYfFqjcwoQV1xV2HtbjCTcOb8Td8TEYjIoILF8tSyfIwDXWGB5
zMQIQxUdQyNiqdBPFcnkAufjk+zLIQ==
=0dG+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200214' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
Fix the following DT dtc warnings for stm32mp1 boards:
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@0:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@1:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@2:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@3:
node has a unit name, but no reg property
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch fix the warning:
dt.dts: Warning (simple_bus_reg): Node /soc/ddr@5A003000
simple-bus unit address format error, expected "5a003000"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
LTDC modifies the clock frequency to adapt it to the display. Such
frequency change is not detected by the FDCAN driver that instead
cache the value at probe and pretend to use it later.
Keep the LTDC alone on PLL4_Q by moving the FDCAN to PLL4_R.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Device tree and binding alignment with kernel v5.5-rc7
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update the driver to use the latest binding from kernel v5.5-rc1:
no more use syscon or regmap to access to pwr register and
only one pwr_regulators node with the compatibility "st,stm32mp1,pwr-reg"
is available.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Device tree and binding alignment with kernel v5.4
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
mcu uart will be used during uart boot for loading sysfw.itb. Since
sysfw is not yet available during uart load, power-domain cannot be
enabled. We need to rely on ROM for doing that, so disable power-domains
and clocks for mcu uart. Also fix the mcu uart frequency.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add scm_conf syscon node and its parents as well as the ethernet phy
node to u-boot.dtsi. This enables ethernet boot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Override the panel compatible string for LCD in U-Boot.
Include U-Boot device tree overrides in device-specific device trees so
that the panel compatible string is used.
Fixes: 8c26739859 ("board: ge: bx50v3: sync devicetrees from Linux")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Enable DM_VIDEO for mx53ppd.
Enable DM_REGULATOR_FIXED and DM_PWM for the backlight.
Remove unused MX53PPD_LCD_POWER.
Remove old (incorrect) setup_iomux_lcd.
Enable backlight via display enable handler.
Use cls command to initiate display in HW agnostic manner.
Modify `failbootcmd' to use lcdputs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Remove old (pre-DM) i2c setup code.
Enable DM i2c.
Convert common code to use DM rtc.
Convert common code to read VPD from eeprom partition.
Convert the generic i2c PMIC init code to use the new da9063 driver.
mx53ppd only:
Correct RTC compatible in device tree.
Enable MXC DM i2c driver.
Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc.
Make GPIO banks available during preloc, since initialisation is done
in board_early_init_f().
Add gpio_request() calls to satisfy the DM_GPIO compatibility API.
Remove unused power configuration.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
These nodes are not in upstream kernel, so move these in u-boot.dtsi
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The 'enable-active-high' DTS property configures GPIO so it is active with
HIGH state (by default it is low).
The 'regulator-boot-on' property indicates that the regulator was enabled
in the 'earlier' stage - i.e. bootloader/firmware.
In the XEA case the 'fec-3v3' was configured (as a "wrapper" on GPIO0_0) in
very early SPL code, so it shouldn't be modified at latter stages.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad
2GB WB IT V1.0A module. They are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports booting from the on-module eMMC only, SDP support is disabled
for now due to missing i.MX 8M Mini USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
Normal Boot
Trying to boot from MMC1
NOTICE: Configuring TZASC380
NOTICE: RDC off
NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty
NOTICE: BL31: Built : 01:11:41, Jan 25 2020
NOTICE: sip svc init
U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Reset cause: POR
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial#
06535149
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Verdin iMX8MM #
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Convert the designware watchdog timer driver to DM and add DT probing
support. Perform minor coding style clean up, like drop superfluous
braces. These ought to be no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
Sync the interrupt properties with the ones from Linux. Also use the
constants provided by the dt-bindings header. Please note, that there
are actual changes/fixes in the irq flags. U-Boot won't use the
interrupt properties anyway. It's just to be consistent with the Linux
device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Also align the fspi node with the kernel one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
IO expanders are required to power cycle SD card. So enable the same
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
J721e SoC has 2 I2C instances in MCU domain and 7 I2C instances in main
domain. Add DT nodes for the same
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable USB0 in peripheral mode so that it be used for DFU
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add alias for mmc/sdmmc so that we can have a fix mmc number for emmc.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add rk3328-sdram-ddr4-666.dtsi for support ddr4 init.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
All rockchip platforms support TPL or SPL-based bootloader
in mainline with U-Boot proper as final stage. For each
stage we need to burn the image on to flash with respective
offsets.
This patch creates a single boot image component using
- binman, for arm32 rockchip platforms
- pad_cat, for arm64 rockchip platforms.
This would help users to get rid of burning different
boot stage images.
The new image called 'u-boot-rockchip.bin'
which can burn into flash like:
₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64
This would support all rockchip platforms, except rk3128
since it doesn't support for SPL yet.
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot specific dtsi file for rk3188 SoC. This
would help to add U-Boot specific dts nodes, properties
which are common across rk3188.
Right now, the file is empty, will add required changes
in future patches.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot specific dtsi file for rk3036 SoC. This
would help to add U-Boot specific dts nodes, properties
which are common across rk3036.
Right now, the file is empty, will add required changes
in future patches.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable winbond SPI flash for ROC-PC-RK3399 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable winbond SPI flash for ROC-PC-RK3399 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the ROC-RK3399-PC device tree changes from Linux
with below commit details:
commit <c36308abe4110e4db362d5e2ae3797834a7b1192> ("arm64: dts:
rockchip: Enable MTD Flash on rk3399-roc-pc")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update the .dts file from the kernel, which carries much more nodes,
some of them we need to enable USB and Ethernet support for the board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sync the device tree files and device tree header files from upstream
Linux kernel, as of 2020-01-08. The commit synced to in the sunxi repo
98d25b0b266d Merge branch 'sunxi/dt-for-5.6' into sunxi/for-next
which is also part of next-20200108.
Changes brought in include:
- cleanup of pinmux node names
- addition of Security ID, MBUS, CSI, crypto engine, video codec,
pmu, and thermal sensor device nodes for both SoCs
- addition of deinterlacing engine device node on H3
- cleanup of RTC device node and addition of its clocks
- various board cleanups and improvements
- removal of pinmux node for GPIO lines
- cpufreq / DVFS
- HDMI output
- UART-based Bluetooth
- audio codec
- USB ports
- new boards
Most of the changes don't concern U-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This add the initial support of the broadcom reference
board bcm968360bg with a bcm68360 SoC.
This board has 512 MB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Use MMC0 for eMMC and MMC2 for SD-card as other Exynos-based boards do.
This allows to use common code to get MMC device id based on the XOM[7:5]
pins.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Card detect line for SD-card on Odroid U3/X2 boards are active low, so
add cd-inverted property to indicate this, as u-boot's GPIO driver doesn't
support specifying line polarity. This restores S5P_SDHCI driver operation
on Odroid U3/X2 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
u-boot uses the same DTS for the all Odroid XU3-based boards, so list
them in the model description to let user know that those boards are
supported.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The ST-Ericsson U8500 SoC has been used in mass-production for
some Android smartphones released around 2012.
In particular, Samsung has released more than 5 different
smartphones based on U8500, e.g.
- Samsung Galaxy S III mini (GT-I8190) "golden"
- Samsung Galaxy S Advance (GT-I9070) "janice"
- Samsung Galaxy Xcover 2 (GT-S7710) "skomer"
and a few others.
Mainline Linux has great support for the Ux500 SoC, so these
smartphones can also run Linux mainline quite well.
Unfortunately, the original Samsung bootloader used on these devices
has limitations that prevent booting Linux mainline directly.
It keeps the L2 cache enabled, which causes Linux to crash very early,
shortly after decompressing the kernel.
Using U-Boot allows to circumvent these limitations. We can let the
Samsung bootloader chain-load U-Boot and U-Boot locks the L2 cache
before booting into Linux. U-Boot has several other advantages
- it supports device-trees directly and we are no longer limited to
flashing Android boot images through Samsung's proprietary download
mode.
The Samsung "stemmy" board covers all Samsung devices based on U8500.
Add minimal support for "stemmy". For now only UART is supported but
this will be extended later.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The NovaThor U8500 SoC was released by ST-Ericsson in 2011.
It was used for some development boards like the CALAO Systems
Snowball SBC, but mass production was primarily for Android
smartphones like the Samsung Galaxy S III mini.
Previous support for U8500 was removed in
commit 68282f55b8 ("arm: Remove unused ST-Ericsson u8500 arch")
since none of the boards were converted to generic boards
before the deadline.
The new code does not have much in common with the previous code.
I have completely rewritten everything, embracing the Driver Model
and device trees wherever possible.
The U8500 support is a bit more minimal for now - my primary
use case is to use U-Boot as alternative bootloader for some of the
U8500 Samsung smartphones. At the moment U-Boot is chain-loaded from
the original Samsung bootloader. A side effect of this is that we
can (temporarily) get away without implementing some functionality
- e.g. all clocks are already enabled by the original bootloader.
More functionality will be added in future patches.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
from https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git/
tag "ux500-armsoc-v5.6-2"
commit 224bf0fe7292 ("ARM: dts: ux500: samsung-golden: Add Bluetooth")
(queued for merge in Linux 5.6)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add device-tree description for the EEPROM devices on Armada 388 SOM rev
2.1.
Another EEPROM is now on Clearfog Pro carrier rev 2.2, and Clearfog Base
rev 1.3.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
The mux mode is embedded in the PAD definition and therefore there is
no need to repeat it in the PAD configuration value (more over since
this information will be masked out when the configuration value is
applied).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add pinmux for USB1 and enable it as a peripheral port in U-Boot
specific dtsi since U-Boot does not support OTG.
Disable USB0 as its not available on the baseboard.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for USB0 and USB1 instances on the AM6 SoC.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
None of these boards boot, but the solution appears to be the same.
All the boards have SPL that is too large. With a few defconfig
options removed, these corresponding options can be removed from
their respective SPL dtb files.
This patch unifies the DM37/OMAP35 boards' -u-boot.dtsi files
to remove gpio's, i2c, bandgap, thermal zones, unneeded uarts, and
unneeded MMC nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
wkup_vtm populates only 1 power-domain cell in it's node. But the
power-domain cell are defined as 2. Due to this the following warning
comes during build:
arch/arm/dts/k3-am654-r5-base-board.dtb: Warning (power_domains_property):
/interconnect@100000/interconnect@28380000/interconnect@42040000/
wkup_vtm@42050000:power-domains: property size (8) too small for cell size 2
Fix this by updating the power-domain cells.
Fixes: cfa6bd549c ("arm: dts: k3-am654-r5-base-board: Add VTM node")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Make the wkup_i2c0 module usable across all stages of U-Boot by adding
the needed definitions including the associated pinmux definitions.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
BeagleBoard.org BeagleBone AI is an open source hardware single board
computer based on the Texas Instruments AM5729 SoC featuring dual-core
1.5GHz Arm Cortex-A15 processor, dual-core C66 digital signal
processor (DSP), quad-core embedded vision engine (EVE), Arm Cortex-M4
processors, dual programmable realtime unit industrial control
subsystems and more. The board features 1GB DDR3L, USB3.0 Type-C, USB
HS Type-A, microHDMI, 16GB eMMC flash, 1G Ethernet, 802.11ac 2/5GHz,
Bluetooth, and BeagleBone expansion headers.
For more information, refer to:
https://beaglebone.ai
The corresponding patch against the mainline linux kernel can be found
at: https://patchwork.kernel.org/patch/11254903/
This patch introduces the BeagleBone AI device tree.
Note that the device use the "ti,tpd12s016" component which is software
compatible with "ti,tpd12s015". Thus we only use the latter driver.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Get clk_xin by name instead of by index to avoid having to put clocks in
the same order in all devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently, the da850-lcdk uses SPL_OF_PLATDATA and manually loads
the necessary source code instead of using the auto-generated,
because the drivers don't properly autogenerate the code.
This patch simply enables the various device tree options to
mimic the da850-evm which doesn't need or use OF_PLATDATA for
device tree support. It does not disable OF_PLATDATA.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
J721e has two instances of Cadence USB3 controller. Add DT nodes for the
same. USB0 is configured to device mode and USB1 is configured to host
mode. For now only high speed mode is supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add missing 'eth-ck' clock to the ethernet node. These clock are used to
generate external clock signal for the PHY in case 'st,eth_ref_clk_sel'
is specified.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch move u-boot properties to -u-boot.dtsi file.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This adds a general board file based on MT7622 SoCs from MediaTek.
This commit is adding the basic boot support for the MT7622 rfb.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Add support for MediaTek MT7622 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This adds a general board file based on MT8512 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8512 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
Add support for MediaTek MT8512 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
IPG clock description is missing for I2C0 and I2C2 busses,
add it. Otherwise we see -ENODATA error when trying to get
I2C clock for these busses.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
imx6ul-14x14-evk does not have a GPIO dedicated for reading the card
detect pin on the eSDHC2 port. In such cases the "broken-cd" property
must be passed, otherwise the card cannot be detected.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
All Tegra chips except Tegra186 have a tegraNNN-u-boot.dtsi. Duplicate
Tegra210's copy of this file for Tegra186. This ensures that a /binman node
exists in U-Boot's control DT. Subsequent to 3c10dc95bd ("binman: Add a
library to access binman entries") this appears to be required. I haven't
really investigated why all this is necessary or how it works, but simply
observed the boot failure listed below, bisected it, noticed the
inconsistency in DT files, and found that fixing it resolved the boot
issue.
U-Boot 2020.01-rc4-00256-g3c10dc95bdd0 (Jan 07 2020 - 10:25:00 -0700)
SoC: tegra186
Model: NVIDIA P2771-0000-500
Board: NVIDIA P2771-0000
DRAM: 7.8 GiB
initcall sequence 00000000fffb7858 failed at call 00000000800955a8 (err=-22)
### ERROR ### Please RESET the board ###
Fixes: 3c10dc95bd ("binman: Add a library to access binman entries")
Fixes: f2faffecb0 ("binman: tegra: Convert to use binman")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch is to build the coresight topology structure of zynq-7000
series according to the docs of coresight and userguide of zynq-7000.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.
This patch replaces the legacy properties with the unified
"wakeup-source" property introduced by:
"Input: gpio_keys - switch to using generic device properties"
(sha1: 700a38b27eefc582099fdf69effacfad0ad738a4)
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Somewhere along recent changes to power control of the wl1831, power-on
became very unreliable on the Ultra96, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16
wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of
this chip, it turned out we need some power-on delay to make things
stable again. In contrast to those other users which define 200 ms,
Ultra96 is already happy with 10 ms.
Fixes: 5869ba0653b9 ("arm64: zynqmp: Add support for Xilinx zcu100-revC")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
s/_/-/ for node names.
It fixes warnings like this:
... Warning (node_name_chars_strict): /cpu_opp_table:
Character '_' not recommended in node name ...
Issues reported by make dtbs W=12
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
zcu102-revB/up are not removing phy from revA properly because of incorrect
name.
Fixes: 2975a42b42 ("arm64: zynqmp: Use ethernet-phy as node name for ethernet phys")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zcu1285 is the same as zcu1275 but it is using Avnet FMC
http://www.ultrazed.org/product/network-fmc-module
Unfortunately not everything is connected now that's why this is only
describing system which Xilinx is using.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removed no-1-8-v property from zynqmp sdhci devicetree nodes to
allow UHS-I capable SD cards to work in SD3.0 UHS modes.
Boards that does not have level shifter for SD, does not support 1.8v.
so no-1-8-v property to sdhci dt nodes should be present in zcu102 Rev-A,B,
zcu104 Rev-A,C, zcu100, zcu1275 Rev-B boards.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Corrected the type of eeprom in device tree for zcu216 boards according
to schematic.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix shunt resistor value for ina226 vccint_ams and vccint_io_bram_ps.
2mOhm shunt was only in early board revision schematics but never got to
real revA board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There shouldn't be a need to use any partition description because it
can be used for writing data anywhere.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
-----BEGIN PGP SIGNATURE-----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=rkHZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200108' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Khadas VIM3L based on Amlogic S905D3 support
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
The i.MX8M Plus Media Applications Processor is part of the growing
mScale family targeting the consumer and industrial market. It brings
an effective Machine Learning and AI accelerator that enables a new
class of applications. It is built in Samsung 14LPP to achieve both
high performance and low power consumption and relies on a powerful
fully coherent core complex based on a quad core ARM Cortex-A53 cluster
and Cortex-M7 low-power coprocessor, audio digital signal processor,
machine learning and graphics accelerators.
Add the basic dtsi support for i.MX8MP.
Patch from Anson Huang for Kernel
https://patchwork.kernel.org/patch/11310915/
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add device tree files for Agilex SoC platform.
socfpga_agilex-u-boot.dtsi and socfpga_agilex_socdk-u-boot.dts contains
Uboot specific DT properties.
socfpga_agilex.dtsi and socfpga_agilex_socdk.dts are from Linux
(kernel/git/dinguyen/linux.git, commit 6f0bf971bacacc)
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add u-boot,dm-pre-reloc for sysmgr and clkmgr nodes to use it in SPL.
In preparation to get base address from DT.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Import the Khadas VIM3L device-tree from [1]
[1] e42617b825f8 ("Linux 5.5-rc1")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Engicam i.CoreM6 1.5 Quad/Dual MIPI dtsi is reusing fec node
from Engicam i.CoreM6 dtsi but have sampe copy of phy-reset-gpio
and phy-mode properties.
So, drop this phy reset methods from imx6qdl-icore-1.5 dsti file.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Similar fix has merged for i.Core MX6Q but missed to update for DL.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync Engicam device tree file from v5.4 linux-next.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync DTS with the mainline Linux and introduce fec node and
regulator configuration for rn5t567 PMU.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Sync DTS with the mainline Linux and introduce fec node.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Sync DTS with the mainline Linux and introduce fec node.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The Embedded Artists COM board is based on NXP i.MX7ULP.
It has a BD70528 PMIC from Rohm with discrete DCDC powering option and
improved current observability (compared to the existing NXP i.MX7ULP EVK).
Add the initial support for the board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Note: gpio7_8 was never used for usb power regulator so we remove it here
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Sync the Linux Kernel 5.4-rc6 device tree for Phytec Phycore
SoM and Segin board based on imx6UL and imx6ULL.
Changes includes Phytec naming convention for the devicetree files.
Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The wdt-reboot node is needed for the sysreset_watchdog driver to
register a watchdog as a reset handler in case 'CONFIG_SYSRESET' is
enabled.
Signed-off-by: Claudius Heine <ch@denx.de>
These DT files are copied from kernel v5.3 with no changes.
This is part 2 of 2 commits. Included are DT files for SOM rev 1.5, and
Hummingboard2 Gate/Edge.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
These DT files are copied from kernel v5.3 with no changes.
This is part 1 of 2 commits. Included are DT files for the original
Cubox-i and Hummingboard Base/Pro.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Copy device trees from linux, keeping them as separate files for
each board to ease future sync.
Update board code to use generic bx50v3 dt initially, then select
the specific dt based on board detection.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
This patch introduces support for i.MX28 based XEA board.
This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb) by using OF_PLATDATA.
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.
U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error
U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM: 128 MiB
MMC: MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet@800f0000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
as we switch to support DM and DTS, rework the existing
DTS trees. Change also Linux specific Device trees, goal
is to push this changes to linux.
Collect U-Boot specific changes in separate "*u-boot*" dts
files.
Signed-off-by: Heiko Schocher <hs@denx.de>
Add device trees from Linux in preparation for driver model
conversions.
device tree files taken from Linux:
71ae5fc87c34: "Merge tag 'linux-kselftest-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest"
and added SPDX license identifier.
Signed-off-by: Heiko Schocher <hs@denx.de>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Update the ddr settings to use the DDR reg config tool rev 0.2.0.
This reduces the aging count(in DDRSS_CTL_274_DATA reg) to 15 in-order
to avoid DSS underflow errors.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
- Fix latest mainline kernel for rk3308
- Update rk3288-evb config to suport OP-TEE
- Fix for firefly-px30 DEBUG_UART channel and make it standalone
- Script make_fit_atf add python3 support
- Fix rk3328 timer with correct COUNTER_FREQUENCY
- Fix rk3328 ATF support with enable spl-fifo-mode
Firefly Core-PX30-JD4 use UART2M1 while PX30 evb using UART2M0, the U-Boot
proper will use the dts setting to do the IOMUX init, and a separate dts
is needed for px30-firefly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
LX2160A PL011 UART driver fetch IP block values using
platform data from board file instead of device tree.
Modified UART nodes in device tree to disable state.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Orangepi Zero Plus 2 is an open-source single-board computer, available
in two Allwinner SOC variants, H3 and H5. We add support for H3 variant
here, as the H5 is already supported.
H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply
Sync dts from linux v5.2 commit:
"ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry"
(sha1: 75f9a058838be9880afd75c4cb14e1bf4fe34a0b)
Commit:
"ARM: dts: sun8i: h3: Refactor the pinctrl node names"
(sha1: a4dc791974e568a15f7f37131729b1a6912f4811)
has been avoided as it breaks U-Boot build.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
commit 3b3e8a37d3
("arm: dts: am335x: sync cpsw/mdio/phy with latest linux - drop phy_id")
did sync with recent linux kernel and replaced therefore the 'phy_id'
property with a phy-handle pointing to the mdio.
This is OK for linux, but introduces trouble with the already running
vxWorks on this target.
So this commit here re-inerts the phy_id property beside the phy-handle
property to be compatible with both.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Add DT nodes related to DMA and CPSW to -u-boot.dtsi to get networking
up on J721e EVM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Based on upstream-linux
See https://github.com/torvalds/linux/commit/f66b2aff.
However made the XSMI register window 0x16 (22) bytes per my reading
of the functional spec. Similar commits in Marvels own repo bump it
to 0x200 (512) bytes but I did not see the reasoning for that.
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/4d932b4.
Also added device-name attributes to prevent ambiguity in the `mdio`
command.
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The AM654 SoC doesn't allow to disabling RGMII TX internal delay in CPSW2G
MAC. Hence, change CPSW2G interface mode to "rgmii-rxid" - RGMII with
internal RX delay provided by the PHY, the MAC will add an TX delay in this
case.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
-----BEGIN PGP SIGNATURE-----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=L2zo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191209' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.01
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
Ever since the conversion to DM PCI, the board was missing the PCIe DT
nodes, hence the PCI did not really work. Fill in the DT nodes and add
missing PCIe device reset.
Moreover, bring the PCIe power domain up before booting Linux. This is
mandatory to keep old broken vendor kernels working, as they do not do
so and depend on the bootloader to bring the power domain up.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Sync the mx7ulp device tree related files with the one from
NXP U-Boot vendor tree (imx_v2019.04_4.19.35_1.0.0).
The mainline support for i.MX7ULP is very premature at this stage.
We should probably re-sync with mainline Linux dts when it gets
in better shape, but for now sync with the U-Boot vendor code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The Firefly ROC_RK3308_CC use ref_clock of input mode,
and rmii pins of m1 group.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3308 only support RMII mode, and if it is output clock
mode, better to use ref_clk pin with drive strength 12ma.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.
And show my best respect to Heiko's work for this solution.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds a general board file based on MT8518 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8518 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
[trini: Migrate env location to defconfig, set ENV_IS_IN_MMC]
Signeed-off-by: Tom Rini <trini@konsulko.com>
Add support for MediaTek MT8518 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
Update the sdmmc2 node for eMMC support on eval board stm32mp157c-ev1.
- update slew-rate for pin configuration
- update "vqmmc-supply"
- remove "st,sig-dir"
- add mandatory "pinctrl-names"
- add "mmc-ddr-3_3v"
This patch solve the eMMC detection issue for command "mmc dev 1".
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Device tree and binding alignment with kernel v5.4-rc4
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Device tree and binding alignment with kernel v5.3
and converted to SPDX.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
-----BEGIN PGP SIGNATURE-----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=4Z+A
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.01' of https://github.com/mbgg/u-boot
- add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
Rename the file bcm283x-uboot.dtsi so that it get
automatically include through the scripts/Makefile.lib
using $(CONFIG_SYS_SOC))-u-boot.dtsi
Without this uarts and pincontroller miss the property dm-pre-reloc
and the first call to bcm283x_mu_serial_ofdata_to_platdata() fails
as the pins are not set correctly.
As a result the U-Boot banner isn't shown on boot.
Before commmit
143256b353 ("fdt: update bcm283x device tree sources to Linux 5.1-rc6 state")
we included bcm283x-uboot.dtsi directly in the device-tree file.
Which got deleted by the metioned commit.
This is a much robuster solution.
Reported-by: Tom Rini <trini@konsulko.com>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Tom Rini <trini@konsulko.com> [RPi 3, 32b and 64b modes]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
In commmit
143256b353 ("fdt: update bcm283x device tree sources to Linux 5.1-rc6 state")
we deleted the label for the node soc from bcm283x.dtsi
As we don't need to add the property dm-pre-reloc to the soc node,
we can delete it from bcm283x-uboot.dtsi
Tested-by: Tom Rini <trini@konsulko.com> [RPi 3, 32b and 64b modes]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
As part of loading trustedfirmware, the SPL is required to place portions
of code into the socs sram but the mmc controllers can only do dma
transfers into the regular memory, not sram.
The results of this are not directly visible in u-boot itself, but
manifest as security-relate cpu aborts during boot of for example Linux.
There were a number of attempts to solve this elegantly but so far
discussion is still ongoing, so to make the board at least boot correctly
put both mmc controllers into fifo-mode, which also circumvents the
issue for now.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add 'ethernet0' as alias for 'gmac0' in S10 device tree.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
The HPS EMAC0 drive strength is changed to 4mA because the initial 8mA
drive strength has caused CE test to fail. This requires changes on the
pad skew for EMAC0 PHY driver. Based on several measurements done, Tx
clock does not require the extra 0.96ns delay which was needed in
Arria10.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add #address-cells and #size-cells to memory node to fix incorrect memory
size decoding in recent Uboot version.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
- remove "synopsys,dw-mipi-dsi" compatible to reduce the device tree
differences between Linux and U-Boot for stm32mp1 platform
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXdJyOg4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXOmuAJ9lF7GyPpv0vZNX1V4UV2EyyOOdbwCfQzHu3Xo+
3VWLV9ZHkVMlfnGbbx0=
=+YuG
-----END PGP SIGNATURE-----
Merge tag 'video-for-v2020.01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix i.MX6ULL evk black screen observed while reboot stress tests
- remove "synopsys,dw-mipi-dsi" compatible to reduce the device tree
differences between Linux and U-Boot for stm32mp1 platform
- Add support for rockchip SoC: PX30, RK3308
- Add and migrate to use common dram driver: PX30, RK3328, RK3399
- Add rk3399 board Tinker-s support
- Board config update for Rock960, Rockpro64
Support tinker-s board. The board is equivalent of tinker board
except of emmc.
TODO:
- support of usb current burst when the board is powered from pc
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
dmc is used to initialize the memory controller. It's needed by
u-boot. Move it in the specific section
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dts file for ROC-RK3308-CC from firefly.
Sync form linux rockchip for v5.5-armsoc/dts64:
"arm64: dts: rockchip: Add devicetree for board roc-rk3308-cc"
(sha1: 4403e1237be3af0977aa23ef399e3496316317a0)
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dts for rk3308 evb, sync from the linux kernel
upstream list [0].
[0]https://patchwork.kernel.org/patch/11201555/
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We should set the init value when vdd_log is enabled, or else the
vdd_log output voltage may not in soc required range.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We should set the init value when vdd_log is enabled, or else the
vdd_log output voltage may not in soc required range.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We should set the init value when vdd_log is enabled, or else the
vdd_log output voltage may not in soc required range.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add vdd_log node according to rock960 schematic V13.
This patch affect two boards:
- Rock960 Model A
- Ficus
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The u-boot specific device tree directives should be in u-boot.dtsi
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The u-boot specific device tree directives should be in u-boot.dtsi
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The u-boot specific pieces in the dts files should be in u-boot.dtsi
not the main files, this allows easier sync with upstream. The
rk3399.dtsi has a mix of both so move them all for consistency.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Fix with missing pmugrf)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The rk3399 VD_CENTER voltage domain is not subject to dynamic voltage
scaling. So the regulator reset voltage of 0.9V is used on this board.
Let u-boot initialize the center voltage to 0.95V as it is done for the
VD_LOGIC domain. This avoids instability and occasional linux kernel
Opses on this board.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The most important change for u-boot is the fix for the vdd-log pwm
voltage regulator to avoid overvoltage for the VD_LOGIC power domain.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Few important regulator power rails fixes are available in
linux-next, so sync them same.
Here is the last commit details:
commit <9f7f9b610e1b7d2dc86c543ab0dfcf781bd42326> ("arm64: dts:
rockchip: Fix roc-rk3399-pc regulator input rails")
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add px30 related devicetrees synced from the Linux kernel.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For there are some structures and functions are common for all rockchip SoCs,
migrate to use the common code so that we can clean up reduandent codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
RK3328 has a similar controller and phy with PX30, so we can use the
common driver for it and remove the duplicate codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable gpio0 in SPL to allow the sdhci driver read the SD card-detect
signal.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Remove the compatible "synopsys,dw-mipi-dsi" added in U-Boot
(it don't exist in Linux kernel binding); it is only used
to bind the generic synopsys UCLASS_DSI_HOST "dw_mipi_dsi" to
the driver "stm32-display-dsi" UCLASS_VIDEO_BRIDGE
This binding is done in Linux kernel drivers without compatible
(dw_mipi_dsi_bind() is called in bind of driver, for example in
drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c).
This patch does the same in U-Boot driver, the STM32 driver
calls during its bind the function device_bind_driver_to_node
to bind the generic driver "dw_mipi_dsi" at the same address.
This patch reduces the device tree differences
between Linux kernel and U-Boot for stm32mp1 platform.
Tested with v2020.01-rc1 on STM32MP157C-EV1 and STM32MP157C-DK2.
The dependency of driver is clearer and the probe order is guaranteed.
STM32MP> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
sysreset 0 [ ] syscon_reboot |-- reboot
simple_bus 0 [ + ] generic_simple_bus |-- soc
serial 0 [ + ] serial_stm32 | |-- serial@40010000
...
video_brid 0 [ + ] stm32-display-dsi | |-- dsi@5a000000
dsi_host 0 [ + ] dw_mipi_dsi | | |-- dsihost
panel 0 [ + ] rm68200_panel | | `-- panel-dsi@0
...
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
-----BEGIN PGP SIGNATURE-----
iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl3BmLkPHHNiYWJpY0Bk
ZW54LmRlAAoJECjE2NMq1et3oVwL/2Z7kCMCjudXNjXqJFSVsCizuzaxkYvUDQCK
g8+P7pdci/xZz8pVvVD5zmpZGRM2hu+7hFQwIlSu7anlRqdW+9cZCAJoeq/4A29c
TkI3w99R0xTDGFlip0zM4vKlQXmC0I0LYbJPVDLjN+zNkhL6QNS3QptONw/3xPzr
Vj5+eztasl5JOnkTFE8yZkfbkekgPbO4h43oje5XwRdRQcwzo4qEFZcxZzvucz39
0RXyvu5qtXvSeVYApXeYcnBD3Mn4rjq26rfn2EEntkO0FbhYBHBjwx3/ozmUaOFR
7AtNyZZSAZFe03egfX6+ODx7tuOTA0PK1LLdogMjLDrOd70px+P7wxY9QZV6hKw9
TC4YlboZK2bjsPyOwIraTWVUvU9YjQzlPT0SYjyIono33Av1Um7RDvp+XeyG7VPC
AYE6luZwhauYNUaGegFPexDxOSRqeAiTLx3kOOeHb4Vb4KkJu4Np7Pma2uiqI00V
4TpWJwhqQPn7lo/N1X9ymBx6iNvt2Q==
=sgCz
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191105
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
rk3328 can use same-as-spl option so next loaders are loaded from the same
medium.
Add the boot order in the rock64 dts otherwise booting from sdcard
will result in u-boot looking into the eMMC.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Specification
- Rockchip RK3399
- LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply
Commit details of rk3399-leez-p710.dts sync from linus tree for Linux 5.4-rc1:
"arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC"
(sha1: fc702ed49a8668a17343811ee28214d845bfc5e6)
Signed-off-by: Andy Yan <andyshrk@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This allows the use of PSCI calls to trusted firmware to
initiate reset and poweroff events with CONFIG_PSCI_RESET and
CONFIG_ARM_PSCI_FW. This is desirable, for example, if the target
board has implemented a custom reset or poweroff procedure in EL3.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The only GPIO bank needed in SPL is GPIO4 and the SPL space is tight.
This patch removes the all but GPIO4 from the spl device tree to
reduce the SPL footprint.
Signed-off-by: Adam Ford <aford173@gmail.com>
The only GPIO bank needed in SPL is GPIO4 and the SPL space is tight.
This patch removes the all but GPIO4 from the spl device tree to
reduce the SPL footprint.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add VTM node for voltage and thermal management. For u-boot, this is needed
for supporting AVS class 0, as the efuse values for the OPPs are stored
under the VTM.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Link the vdd-supplies for the voltage domains under the VTM node. Also,
enable the node under SPL. This will enable the AVS class 0 support on
am65x-evm board.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
MPU voltage on AM65x-evm is controlled via the TPS62363 chip attached
to i2c0 bus. Add device node for this so that it can be controlled via
a regulator driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Add VTM node for voltage and thermal management. For u-boot, this is needed
for supporting AVS class 0, as the efuse values for the OPPs are stored
under the VTM.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
with u-boot,dm-spl added for imx8qm-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This commit adds support for the brppt2 board. The board is based on the
i.mx6 dual-lite SoC.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for
DRAM and linux suspend voltage requirement.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Migrate to DM_VIDEO, update the device tree and remove code that is no
longer necessary.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
This updates the i.MX8MQ device trees and, necessarily, also the
i.MX8MQ clock bindings. These are taken verbatim from from the
Linux kernel version v5.4-rc2, which three small changes which
were already part of the previous device tree:
* Keep the PSCI reserved memory range
* Keep the alias for ethernet, so that the MAC address can be set
* Keep the modified #include for the IOMUXC pins
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Acked-by: Peng Fan <peng.fan@nxp.com>
This commit converts mccmon6's u-boot proper (in a single commit to avoid
build breaks) to use solely DM/DTS.
The DTS description of the mccmon6 has been ported from Linux kernel
(v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add u-boot,dm-pre-reloc properties for uart pinmux configuration
nodes, which enables UART as early as possible (before relocation).
Without this we miss almost the half of output (U-boot version,
CPU defails, Reset cause, DRAM details etc.).
Fixes: cd69e8ef9b ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm")
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to
keep original imx6ull-colibri.dts in sync with Linux.
Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi +
additionally fix checkpatch warnings.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Add the address spaces for the R5F cores in MCU domain to the ranges
property of the cbass_mcu interconnect node so that the addresses
within the R5F nodes can be translated properly by the relevant OF
address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use the 3733MTs DDR configuration that is auto generated from
DDR_Regconfig tool.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
Added the following registers to the DDR configuration:
- ACIOCR0,
- ACIOCR3,
- V2H_CTL_REG,
- DX8SLxDQSCTL.
Modified enable_dqs_pd and disable_dqs_pd to only touch the associated
bit fields for pullup and pulldown registers (to preserve slew rate and
other bits in that same register). Also update the dts files in the same
patch to maintain git bisectability.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The current configuration of DDR on AM654 base board is for 1600MTs but
the file name is specified as k3-am654-base-board-ddr4-1600MHz.dtsi.
Since 1600MHz is misleading, rename it to
k3-am654-base-board-ddr4-1600MTs.dtsi
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add usb peripheral and usb phy nodes in spl to enable SPL_DFU bootmode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdspnqAAoJEB6zHgIOrC/Ixi4IAJEEiCZPu6Z3fbkFX/Um7vCX
eMTltJN8nz4oiSi3xdx3ejueqWdW3F8VuCkHb0j0bVAhMlUlVgwCzfd0cD+D2iwS
jkrgzASNAr+JeYKYEdWqqfaUxOCd2qfuBu9EXlpvKQLWLt+KRfsOsHWcgR4bf095
aGCihvd/fKhKYUvbf5cEQnsWa3UwtsKk4Web5MKjxXx3p0iVNlu4KLd/vDWfTios
X1NqiO5ZjXNrDxyG6Aj8lgDXlE5kfeKaN/aCJU1/0U2cXm8JRu2w2dv1P/e/kU+j
NHIGzICAG4Lk/4gQTeuohJxLyvj7K3i1H12ik9Qeh4H1/5fsyybyltGUo7H443s=
=JYe3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2020.01 cycle
This feature set includes Eugen's work on a new tiny flexcom driver and
eeprom mac retrieval for the sam9x60-ek board.
Sync Kernel DTS for Allwinner H6 boards.
Drop /omit-if-no-ref/ keyword as it's not supported by U-boot.
commit <d45331b00ddb> Linux 5.3-rc4
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
The Linux kernel upstream has chosen to create and use a separate device tree
for the eMMC variants instead of adding eMMC support existing device tree. These
changes to Linux kernel are queued for Linux 5.4.
commit <02bb66b347ff8115f53948f86b884e008ba385b9> ("arm64: dts:
allwinner: a64: Add A64 OlinuXino board (with eMMC)")
This patch has been tested on A64-OLinuXino-1Ge16GW and is based on Linux
device-tree and a64-olinuxino_defconfig.
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
[jagan: updated linux-next commit details]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
SoPine has winbond SPI-FLASH, so enable the same in defconfig
and add aliases for spi0 in -u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for System Controller available on e-a2197-00 base board.
System is very similar to p-a2197-00 board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are use cases where lpd watchdog can be configured for APU use. By
design this IP should be listed in zynqmp.dtsi to make sure that node is
properly enabled by DTG.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch updates the nand device tree node properties as per
updated driver.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add gpio phy reset via I2C expander TCA6416 on board ZCU102.
A warning call trace is observer in probe when this reset is called
from context that can sleep. Keep this commented until that is
resolved in phylib.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The DP83867 strap control workaround is already present in Linux kernel
mainline binding. All these Xilinx boards require this quirk.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The si570 clock frequency should be 156.25MHz as per datasheet.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently zcu102 Rev1.0 board includes RevA sdhci dt node which has
no-1-8-v property. Since Rev1.0 has level shifters delete this
property to enable support for 1.8v.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mainline has done this switch and there is no reason not to switch it too.
Mainline U-Boot patch which has done that switch:
"dts: switch spi-flash to jedec, spi-nor compatible"
(sha1: ffd4c7c2ec)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added tps53679 compatible string to tps53681. They are both compatible to
each other and tps53679 has Linux driver already.
Signed-off-by: Nishant Mittal <nishant.mittal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ethernet phys based on devicetree specification should be using
ethernet-phy@ node name instead of pure phy@.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP based System controller is present on Versal boards. This patch is
aligning names with Versal to follow the spec.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DT binding was reviewed in Linux by commit b0b41af12a1b
("dt-bindings: memory: Add pl353 smc controller devicetree binding
information") that's why this fragment can be also added to U-Boot
repository.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As the PHY driver now handles the transitions of USB power domain, we
must add this information in the node of each PHY.
Also, the phy are expected in the "phys" property, not "usb-phys".
Also add the aliases for the USB ports on boards with more than a single
port.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
J721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node for the
same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add DT node for HyperBus Memory Controller in the FSS. On J721e, its not
possible to use OSPI0 and HBMC simultaneously as they are muxed within
the Flash Subsystem hence disable HBMC by default as keep OSPI enabled.
Bootloader will fixup DT when it detects HyperFlash instead of OSPI.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Rename meson-g12a-u-boot.dtsi into meson-g12-common-u-boot.dtsi to
match the new DT architecture and add meson-sm1-sei610-u-boot.dtsi
to handle the U-Boot specific DT for graphics.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In Linux meson-g12-common.dtsi was introduced as well as new g12b nodes
and headers, as dependencies of new meson-g12b-a311d-khadas-vim3.dts.
Copied from da0c9ea146cb ("Linux 5.4-rc2")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Like the meson-gx support, add the U-Boot specific bits in DT
to support graphics on G12A SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
-----BEGIN PGP SIGNATURE-----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=J8jd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191014' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191014
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
This commit adds new file - imx6q-kp-u-boot.dtsi with a set of u-boot
specific properties for imx6q KP device.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
With the 256KB of OCRAM available to SPL now, there should be
enough room to enable the pinmuxing in SPL from the device tree.
This patch enables SPL_PINCTRL et al and adds the serial and
usdhc pin mux references to the -u-boot.dtsi file so the pins can be
configured from the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Main uart0 is used as debug console by both R5SPL and A72 bootloader and
Linux. So mark it as shared device so that power-domain request is
successful by both cores.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This follows the linux header rules to avoid conflict bitfields.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This adds PCIe and its PHY nodes for MT7623.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This commit add a spi-nor device in the bcm96850xref device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Kursad Oney <kursad.oney@broadcom.com>
This commit add a hsspi controller in the bcm6858 device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Kursad Oney <kursad.oney@broadcom.com>
This change adds a spi nor flash device to the bcm963158 board.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
This change adds the hsspi controller to the 63158 dtsi.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
The AM65x SoCs has a single dual-core Arm Cortex-R5F processor
subsystem/cluster (MCU_R5FSS0) within the MCU domain. This cluster
can be configured at boot time to be either run in a LockStep mode
or in an Asymmetric Multi Processing (AMP) fashion in Split-mode.
This subsystem has 64 KB each Tightly-Coupled Memory (TCM) internal
memories for each core split between two banks - ATCM and BTCM
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5 clusters such as the absence of
an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT node for the MCU domain R5F cluster/subsystem, the two
R5 cores are added as child nodes to the main cluster/subsystem node.
The cluster is configured to run in Split-mode by default, with the
ATCMs enabled to allow the R5 cores to execute code from DDR with
boot-strapping code from ATCM. The inter-processor communication
between the main A72 cores and these processors is achieved through
shared memory and Mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have a single TMS320C71x DSP Subsystem in the MAIN
voltage domain containing the next-generation C711 CPU core. The
subsystem has 32 KB of L1D configurable SRAM/Cache and 512 KB of
L2 configurable SRAM/Cache. This subsystem has a CMMU but is not
used currently. The inter-processor communication between the main
A72 cores and the C711 processor is achieved through shared memory
and a Mailbox. Add the DT node for this DSP processor sub-system
in the common k3-j721e-main.dtsi file.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have two TMS320C66x DSP Core Subsystems (C66x CorePacs)
in the MAIN voltage domain, each with a C66x Fixed/Floating-Point DSP
Core, and 32 KB of L1P & L1D configurable SRAMs/Cache and an additional
288 KB of L2 configurable SRAM/Cache. These subsystems do not have
an MMU but contain a Region Address Translator (RAT) sub-module for
translating 32-bit processor addresses into larger bus addresses.
The inter-processor communication between the main A72 cores and
these processors is achieved through shared memory and Mailboxes.
Add the DT nodes for these DSP processor sub-systems in the common
k3-j721e-main.dtsi file.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have 3 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster (MCU_R5FSS0) is present within
the MCU domain, and the remaining two clusters are present in the
MAIN domain (MAIN_R5FSS0 & MAIN_R5FSS1). Each of these can be
configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. These
subsystems have 64 KB each Tightly-Coupled Memory (TCM) internal
memories for each core split between two banks - ATCM and BTCM
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5 clusters such as the absence of
an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT nodes for these two MAIN domain R5F cluster/subsystems,
the two R5 cores are each added as child nodes to the corresponding
main cluster node. Configure SS0 in split mode an SS1 in lockstep mode,
with the ATCMs enabled to allow the R5 cores to execute code from DDR
with boot-strapping code from ATCM.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have 3 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster (MCU_R5FSS0) is present within
the MCU domain, and the remaining two clusters are present in the
MAIN domain (MAIN_R5FSS0 & MAIN_R5FSS1). Each of these can be
configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. These
subsystems have 64 KB each Tightly-Coupled Memory (TCM) internal
memories for each core split between two banks - ATCM and BTCM
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5 clusters such as the absence of
an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT node for the MCU domain R5F cluster/subsystem, the two
R5 cores are added as child nodes to the main cluster/subsystem node.
The cluster is configured to run in LockStep mode by default, with the
ATCMs enabled to allow the R5 cores to execute code from DDR with
boot-strapping code from ATCM. The inter-processor communication
between the main A72 cores and these processors is achieved through
shared memory and Mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Although we currently use the MAIN_UART0 for R5 SPL console output there
are cases where we require access to the MCU_UART0 as well for example in
case of UART-based Y-Modem boot. To support these scenarios add related
DTS definitions to be able to use that UART early on.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Pick minor changes from the downstream DT, disable MMC, add GMAC0 node
and adjust PHY skew settings for GMAC1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Since convert dm_video, unused code introduced, so remove this
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Import i.MX8MM pin func from Linux Kernel,
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Import i.MX8MM dtsi from Linux Kernel,
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for the power domain controller that's used on the
i.MX8MQ. This will be needed to be able to power on the PCIe
controller. Bindings taken from Linux, driver implementation
taken from the i.MX8 power domain controller and adjusted for
the i.MX8M SoC.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
After this change it is possible to use imx28-<board>-u-boot.dtsi with
the imx28-u-boot.dtsi explicitly included without breaking setup from
imx28-<board>.dts file.
The problem is that the imx28.dtsi included in a wrong place overrides the
changes made in imx28-<board>.dts. As a result some devices are "disabled"
in the final DTB.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit enables support for CONFIG_WDT in the U-Boot proper. Moreover,
the SYSRESET_WATCHDOG driver is used to support 'reset' command.
As SPL is not yet ready for DM conversion, the CONFIG_HW_WATCHDOG is
enabled for it. This allows the legacy SPL code to work properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add the initial support for the pico-imx6 variants.
DDR initialization is based on the TechNexion's U-Boot code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The changes were added by following patch:
commit <9002e735e717> ("imx: mx6sabresd: fix boot hang with video")
commit <f45ec8fcfb86> ("imx6: dts: add 'u-boot, dm-pre-reloc' to soc and ipu nodes")
Let's move the U-Boot specific change to imx6qdl-u-boot.dtsi
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
To support DM_VIDEO,
Add display node for lcdif
Drop board iomuxc settings.
Enable DM_VIDEO
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible
with i.MX6ULL. so most code of i.MX6ULL can be reused
by i.MX6ULZ.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Import kernel dts for i.MX6ULZ from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6ULL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6UL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The following patch adds a mailbox node and firmware node to following the
mainline DT.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar SCs but different wiring.
- dc_i2c is connected to X-PRC cards that's why label is required to have
an option to hook up some devices.
- Exactly identify i2c devices on x-prc boards.
In case of missing i2c connection devices won't be accessible.
- USB 0 should be device mode with super speed.
- USB 1 should be host mode.
- Fix i2c mux reset pin entry - commented, not verified.
- Fix i2c1 eeprom compatible string - it is an ST 128Kbit device.
Need to use atmel fallback.
- Fix si570 I2C slave address and add corresponding part numbers.
- Enable AMS for system monitoring.
- phy reset property should be commented because it will throw a
warning dump when called from context that can sleep.
No support for phys property (zynqmp phy driver) with SGMII.
Add is-internal-pcspma property required by uboot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Change has been done across the whole tree only zynqmp-mini-qspi hasn't
been fixed.
Origin changed done by commit ffd4c7c2ec
("dts: switch spi-flash to jedec, spi-nor compatible")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added alias for usb node in dts file.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This node is used by qspi driver for supporting qspi boot mode in SPL.
Similar changes have beeen done by commit a9022b017a
("ARM64: zynqmp: Add u-boot,dm-pre-reloc to clk nodes")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The sam9x60 qspi controller uses 2 clocks, one for the peripheral register
access, the other for the qspi core and phy. Both are mandatory.
Enable the qspi node together with the SST26VF064B qspi nor flash
memory. Booting from the QSPI NOR flash is now possible.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add Ethernet controller to dtsi file and enable it on sam9x60ek
platform connected with rmii.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
add device tree files for sam9x60ek board with below changes.
- Add initial device nodes (pmc, pinctrl, sdhc, dbgu & pit)
- Add the reg property for the pinctrl node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[prasanthi.chellakumar@microchip.com: fix style/whitespace issues]
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
[nicolas.ferre@microchip.com:
- fix gclk,
- fix pio/pinctrl controller definition and allow to have more
than only PIOA for this SoC,
- removing pinctrl address]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[claudiu.beznea@microchip.com:
- use SAM9X60's compatible for pinctrl
- add drive strength and slew rate options for SDMMC0 pins.]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
[tudor.ambarus@microchip.com:
- u-boot,dm-pre-reloc property in dedicated file,
- fix pit len, starts from 0xFFFFFE40 and it is of len 0x10]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add node for hlcld for u-boot logo display at boot.
This is compatible with the Precision Design Associates (PDA) TM5000 screen.
Timings are compatible with simple panel from Linux, panel name is
pda_91_00156_a0
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
qspi1 does not have an alias/seq number. This is required for
SPL default SF bus booting for the boards that have this SoC
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add support for the SAMA5D27-WLSOM1-EK. It's based on the Microchip
WireLess SoM which contains the SAMa5D27 LPDDR2 2Gbits SiP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[eugen.hristev@microchip.com]: added u-boot specific dtsi and ported to 2019.10
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The SPL device tree is missing the entires for gpio1, uart1, usdhc1 and
usdhc2. This creates the missing imx6q-logicpd-u-boot.dtsi file
which will enable these functions so SPL can properly setup UART, detect
microSD card, and startup.
Fixes: 8f4691e31a ("ARM: imx6q_logic: With SPL_OF_CONTROL enabled,
remove MMC init")
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch restores commit c49d0ac38a ("ARM: dts: rmobile: Increase off-on
delay on the SD Vcc regulator"), which was accidentally dropped during DT
resync in commit 317d13ac63 ("ARM: dts: rmobile: Synchronize Gen3 DTs with
Linux 5.0").
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fixes: 317d13ac63 ("ARM: dts: rmobile: Synchronize Gen3 DTs with Linux 5.0")
Tinker board needs to mux all the sdmmc gpio and
activate the regulator connected to bank 7. Remove
all the bank that are not in use and mark them as dm,spl
so-that it would initialize at SPL.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
According to the latest am572x[1] and dra74x[2] data manuals, mmc3
default, hs, sdr12 and sdr25 modes use iodelay values given in
MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
selected and correct iodelay values are configured.
[1] http://www.ti.com/lit/ds/symlink/am5728.pdf
[2] http://www.ti.com/lit/ds/symlink/dra746.pdf
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add device tree from Linux for driver model conversion
and enable OF_CONTROL. This will remove the following compile
warning:
==================================================
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
===================================================
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Add the device-tree structure describing the MUX in board dts.
QDS board has an on-board RGMII PHY and 4 slots for extension cards.
All these can be accessed over MDIO through a MDIO MUX controlled
over I2C.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add nodes for the Aspeed SD controllers with their necessary properties.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Implicitly Marvell MDIO driver uses DT node names for devices, but in this
case that is not unique. Set MDIO device names for master/slave to
cpm/cps.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alignment with kernel patch proposal for binding:
[PATCH v4 0/8] stm32 m4 remoteproc on STM32MP157c
https://lkml.org/lkml/2019/5/14/159
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Due to kernel DT alignment, pwr-supply is renamed to vdd-supply
and is a subnode of pwr-regulators.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As for Audio codec IC, HDMI IC is not "IO safe".
HDMI regulators (v3v3 and v1v2) must be enabled to allow
I2C1 bus usage. HDMI IC must be under reset during power up
and keep HDMI and AUDIO devices in reset while they are not
used in U-Boot to keep them in low power mode
(each device can be kept in reset independently keeping their
power supplies ON until kernel).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Avoid U-Boot auto-boot interruption for line break detection
on console when the RX line connected to STLINK is floating
(-IO error in getc cause by framing error and testc return 1)
Same workaround is applied on all the STMicroelectonics board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The pre-relocation probe is needed to reserve video frame buffer
in video_reserve() for all the board;
LDTC must be tagged prereloc in SOC U-Boot dtsi file.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add node in DT and avoid error to search UCLASS_SYSRESET in
board_f.c::print_resetinfo() and lost 1.6s in U-Boot
for the trusted boot chain.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch adds independent watchdog support for stm32mp157c
in SPL.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update DDR configuration with the latest update:
- Change DQSGE to 1 for DDR3, to cure missing DQS preamble.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When the pinmux configuration was added, it was accidentally placed into
the omap3_pmx_wkup node when it should have been placed into the
omap3_pmx_core. This error was accidentally propagated to U-Boot by
me when I blindly copied the device tree from Linux.
This patch moves the i2c2_pins and i2c3_pins to the correct node
which should eliminate i2c bus errors and timeouts due to the fact
the bootloader uses the save device tree that no longer properly
assigns these pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
According to rock64 schemetic, both VCC_HOST1_5V and VCC_HOST_5V are
controlled by USB20_HOST_DRV(GPIO0A2), fix it so that we can get correct
power supply for USB HOST ports.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB host support on GR Peach board.
To use USB host on GR Peach, it might be necessary to solder JP3 header
onto the board first and then short it. Shorting JP3 is mandatory to let
the U5 regulator to supply VBUS to the CN3 USB port.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 for ls1088aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch adds some slave nodes to support the i2c dm on the device
side under the i2c0 controller.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
One ls1088a, there are four I2C controllers. So add all I2C node
for ls1088a in device tree.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the ds3232-rtc node under the i2c0->i2c-mux@77->i2c@0 for ls2088aqds
boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add some slave nodes to support the i2c dm on the device side under the i2c0.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
One ls2088a, there are four I2C controllers. So add I2C nodes in dts
for ls2088a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the pcf2127-rtc node under the i2c1 in dts for ls1028aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add pca9547 node to support i2c multiplexer under the i2c0 controller
in dts for ls1028aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add some slave nodes to support the i2c dm on the device side under the i2c0.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 in dts for
lx2160aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Lx2160ardb need to use i2c0 before relocation, so we also need to set
u-boot, dm-pre-reloc to initialize node before relocation.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Adds the pcf2127-rtc node under the i2c4 node dts of lx2160ardb boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
In lx2160a soc, there are eight i2c controllers, this patch adds i2c
nodes for lx2160a, and the gpio2 nodes on which the i2c4 controller
depends.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
TI HS platforms generate *dtb_HS binary blobs and there is no
rule for cleanup. Added entry for cleanup in clean-files target.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
