Add the initial support for the pico-imx6 variants.
DDR initialization is based on the TechNexion's U-Boot code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Import kernel dts for i.MX6ULZ from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Similar SCs but different wiring.
- dc_i2c is connected to X-PRC cards that's why label is required to have
an option to hook up some devices.
- Exactly identify i2c devices on x-prc boards.
In case of missing i2c connection devices won't be accessible.
- USB 0 should be device mode with super speed.
- USB 1 should be host mode.
- Fix i2c mux reset pin entry - commented, not verified.
- Fix i2c1 eeprom compatible string - it is an ST 128Kbit device.
Need to use atmel fallback.
- Fix si570 I2C slave address and add corresponding part numbers.
- Enable AMS for system monitoring.
- phy reset property should be commented because it will throw a
warning dump when called from context that can sleep.
No support for phys property (zynqmp phy driver) with SGMII.
Add is-internal-pcspma property required by uboot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
add device tree files for sam9x60ek board with below changes.
- Add initial device nodes (pmc, pinctrl, sdhc, dbgu & pit)
- Add the reg property for the pinctrl node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[prasanthi.chellakumar@microchip.com: fix style/whitespace issues]
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
[nicolas.ferre@microchip.com:
- fix gclk,
- fix pio/pinctrl controller definition and allow to have more
than only PIOA for this SoC,
- removing pinctrl address]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[claudiu.beznea@microchip.com:
- use SAM9X60's compatible for pinctrl
- add drive strength and slew rate options for SDMMC0 pins.]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
[tudor.ambarus@microchip.com:
- u-boot,dm-pre-reloc property in dedicated file,
- fix pit len, starts from 0xFFFFFE40 and it is of len 0x10]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add support for the SAMA5D27-WLSOM1-EK. It's based on the Microchip
WireLess SoM which contains the SAMa5D27 LPDDR2 2Gbits SiP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[eugen.hristev@microchip.com]: added u-boot specific dtsi and ported to 2019.10
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add device tree from Linux for driver model conversion
and enable OF_CONTROL. This will remove the following compile
warning:
==================================================
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
===================================================
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
TI HS platforms generate *dtb_HS binary blobs and there is no
rule for cleanup. Added entry for cleanup in clean-files target.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This commit adds support for the B&R brsmarc1 SoM.
The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Import Linux 5.2-rc1 sei510 DT from 5f9e832c1370 ("Linus 5.3-rc1") for the
meson-g12a-sei510 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This commit adds devicetree for Hikey960 board. Most of the contents are
copied from Linux kernel with some modifications for u-boot. To be
more precise, SD card's speed related properties are removed due to a
bug in u-boot clock implementation. Hence forcing the SD controller to
work in standard speed.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- Add rk3399 boards Khadas Edge/-V/-Captain
- Add fully souce code support for rk3328 including TPL/DRAM init
- Enable boot from eMMC for rk3399 rock960/ficus boards
- turn on the IO supply for dw_mmc
Add devicetree support for Khadas Edge-Captain.
Khadas Captain is the carrier board for Khadas Edge.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge-V.
Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge.
Khadas Edge is an expandable Rockchip RK3399 board with goldfinger.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP
- USB 3.0, 2.0
- USB Type C power and data
- 16MB SPI Flash
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
-----BEGIN PGP SIGNATURE-----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=Q5fc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190731' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- sync Amlogic G12A DT with linux 5.3-rc1
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
Import HardKernel Odroid-N2 DT from Linux 5.3-rc1, commit 5f9e832c1370
("Linus 5.3-rc1") based on an Amlogic G12B S922X SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Avnet UltraZed-EV Starter Kit is composed by the UltraZed-EV SoM and the
only publicly-available compatible carrier card. The SoM is based on the EV
version of the Xilinx ZynqMP SoC+FPGA.
The psu_init_gpl.c file has been generated from the board definition files
at [0] using Vivado 2018.3 and then minimized by
tools/zynqmp_psu_init_minimize.sh. Manually removed serdes init code since
it is not mentioned in device tree and fixed a checkpatch error.
[0] 3686c9ff7d/ultrazed_7ev_cc/1.1
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Name of this platform has changed and released to customers that's why
name has also changed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: uboot
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, and an expansion header.
Additionally there is a HDMI port, DSI port, and camera port only
on the MT8167 version of the board.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8516
board on the eMMC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Common Processor board is the baseboard that has most of the actual connectors,
power supply etc. A SOM (System on Module) is plugged on to the common
processor board and this contains the SoC, PMIC, DDR and basic highspeed
components necessary for functionality. Add initial dt support for this
common processor board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
Supported boot media: microSD card (via SPL), QSPI flash.
Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).
Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).
To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.
eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:
- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
get overwritten during copying of the u-boot.bin payload from MMC to
DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This device tree adds support for DHCOM iMX6 duallite and solo
deriviates.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.
The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.
Signed-off-by: David Lechner <david@lechnology.com>
After the transition to DM, only the mx6dl/solo wandboard
is supported.
Add FIT image support so that all the wandboard variants
can be supported, like it was prior to the DM conversion.
Successfully booted Linux on mx6q/solo/qp wandboards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Place dtbs under SoC level rather than board level.
imx6q-novena.dtb and imx6dl-wandboard-revb1.dtb were
placed under the board config option, so move them
to SoC level.
This also aligns with the kernel dts Makefile format.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Import iMX53 M53Menlo device tree from Linux next-20190607 3f310e51ceb1 .
Enable DT control in full U-Boot . Add U-Boot extras into separate DTSi,
the GPIO controllers need to be inited early, otherwise m53_set_clock()
won't be able to detect the correct CPU clock frequency by reading the
GPIO.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
rk3328-rock64.dts has been taken from Linux kernel commit
cff6d1d6f88b ("arm64: dts: rockchip: enable HS200 for eMMC on rock64")
with minor modifications (drop nodes not known by rk3328.dtsi).
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Updating the bcm283x device tree sources adds the device trees for
- Raspberry Pi 3 Model A+
- Raspberry Pi 3 Model B+
- Raspberry Pi Compute Module IO board rev1
- Raspberry Pi Compute Module 3 IO board V3.0
- Raspberry Pi Zero
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2C9f
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot
- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
Import iMX6SX VINING|2000 device tree from Linux 5.1.1 b724e9356404 .
Enable DT control in full U-Boot .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT
V1.0B module. Unlike the V1.0A early access samples exclusively booting
from SD card, they are now strapped to boot from eFuses which are
factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Gigabit Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QM as of yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Import iMX6Q Novena device tree from Linux 5.1-rc7 37624b58542f .
Enable DT control in full U-Boot .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Import DHCOM iMX6 PDK2 device tree from Linux 5.1.1 b724e9356404 .
Enable DT control in full U-Boot .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Add device tree to Makefile to avoid newly introduced error:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
make[1]: *** [dts/Makefile:28: arch/arm/dts/imx6-apalis.dtb] Error 1
make: *** [Makefile:1009: dts/dt.dtb] Error 2
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Add support for Avenger96 board from Arrow Electronics based on STM32MP157
MPU. This board is one of the Consumer Edition (CE) boards of the 96Boards
family and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add initial support for Rock PI 4 board.
Specification
- Rockchip RK3399
- LPDDR4
- eMMC
- SD card slot
- RTL8211E 1Gbps
- HDMI In/Out, DP, MIPI DSI/CSI
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type
Commit details of rk3399-rock-pi-4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: add ROCK Pi 4 DTS support"
(sha1: 1b5715c602fda7b812af0e190eddcce2812e5417)
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add initial support for Rockpro64 board.
Specification
- Rockchip RK3399
- 2/4GB Dual-Channel LPDDR3
- SD card slot
- eMMC socket
- 128Mb SPI Flash
- Gigabit ethernet
- PCIe 4X slot
- WiFI/BT module socket
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-rockpro64.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: rockpro64 dts add usb regulator"
(sha1: 6db644c79c8d45d73b56bc389aebd85fc3679beb)
'Akash' has sent an initial patch before, so I keep him as board
maintainer and I'm co-maintainer based on our conversation.
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Re-add support for Aries Embedded MCV SoM, which is CycloneV based
and the associated MCVEVK and MCVEVP baseboard. The board can boot
from eMMC. Ethernet and USB is supported.
The Aries Embedded boards have been removed with commit 03b54997d5
("board/aries: Remove"). I will now take care of them.
The device-tree files are from mainline Linux commit e93c9c99a629
("Linux v5.1)".
Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de>
CC: Marek Vasut <marex@denx.de>
CC: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Improvements and new features:
- split more rockchip pinctrl_core feature into per SoC
- enable TPL for evb-rk3399 board
- enable TPL/SPL for evb-px5 board
- enable TPL and OP-TEE support for evb-rk3229
- update fix in arm common assembly start code for rockchip header file
- update default SPL_FIT_GENERATOR for rockchip
- rk3399 boards update to use '-u-boot.dtsi'
- add new rk3399 boards: Nanopi M4, Nanopc T4
- enable sound for chromebook_minnie
Add initial support for Nanopc T4 board.
Specification
- Rockchip RK3399
- Dual-Channel 4GB LPDDR3-1866
- SD card slot
- 16GB eMMC
- RTL8211E 1Gbps
- AP6356S WiFI/BT
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-nanopc-t4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: Add NanoPC-T4 IR receiver"
(sha1: 95658e21b1707ad7844f873db2fdaa295109a5a3)
Tested-by: Daniel Gröber <dxld@darkboxed.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and
like some of the other similar boards requires bin_hdr.
bin_hdr (DDR3 init stage) is currently retrieved from the stock
bootloader and compiled into the kwb image.
Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip
support and writing env to SPI flash.
Signed-off-by: Luka Kovacic <me@lukakovacic.xyz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Olimex A64-Teres-I board is a mainboard (the only one so far)
for Olimex Teres-I DIY laptop kit.
Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- MicroSD Slot
- 16GB eMMC Flash
- eDP LCD display
- HDMI
- USB Host
- Battery management
- 5V DC power supply
- Certified Open Source Hardware (OSHW)
Works:
- i2C
- MMC/SD
- PWM backlight
Known broken:
- Internal keyboard (seems to be because the keyboard firmware loads a
bootloader first, and then disconnects bootloader and connect real
keyboard). External ones connected to the USB port work fine.
This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).
Linux commit details about the sun50i-a64-teres-i.dts sync:
"arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins"
(sha1: d91ebb95b96c8840932dc3a10c9f243712555467)
Cosmetic warnings regarding whitespace and placement of SPDX notice for
dts file was ignored.
config and .dtsi file are adapted from pinebook files.
Tested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: move board entry in MAINTAINERS file at proper position]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Sometimes u-boot specific dtsi files are included
automatically which would build for entire rockchip SoC,
even-though the respective dtsi should used it for specific
family of rockchip SoC.
- Sometimes u-boot specific dts nodes or properties can use
config macros from respective rockchip family include/configs
files, example CONFIG_SPL_PAD_TO.
So, it's better to compile the dtbs based on the respective
rockchip family types rather than rockchip itself to avoid
compilation issues.
This patch organize the existing dtb's based on the rockchip
family types.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add board code and DTs for Renesas RZ/A1 SoC-based GR-Peach,
which is a cheap development platform with RZ/A1H SoC. The
DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Currently supported are UART, ethernet and RPC SPI. The board
can be booted from RPC SPI by writing the u-boot.bin binary
to the beginning of the SPI NOR, e.g. using the "sf" command.
The board can also be booted via JTAG by setting text base to
0x20020000, loading u-boot.bin there via JTAG and executing it
from that address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add device-tree files from linux 5.1-rc7 needed to complete support
for PocketBeagle.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
-----BEGIN PGP SIGNATURE-----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=CzWQ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
Add the device trees for
* vexpress_ca5x2_defconfig
* vexpress_ca9x4_defconfig
* vexpress_ca15_tc2_defconfig
as available in Linux 5.1 rc5.
We are using the vexpress_ca15_tc2_defconfig and vexpress_ca9x4_defconfig
for Travis testing via QEMU.
The UEFI base Embedded Base Boot Requirements Specification (EBBR) requires
that an embedded board either provides a device tree or an ACPI table.
All block devices are meant to be moved to the driver model. On ARM this
requires a device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is Marvell's Kirkwood development board. It has the following
features
- 512M DDR2
- 2 PCI connectors
- 1 x1 PCI-e interface
- 1 Gigabit Ethernet Port
- 2 SATA Ports
- USB 2.0 Interface
- SDIO
- 128M NAND Flash
- 16M SPI Flash
It can be strapped to boot from SPI or NAND so there are two defconfigs
(one per boot media).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The following Kirkwood dtb build targets are currently missing:
kirkwood-openrd-base.dtb
kirkwood-openrd-client.dtb
kirkwood-openrd-ultimate.dtb
This patch adds them to the Makefile to fix the build error.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch imports the Linux kernel base board imx7d-pico.dtsi,
pi board imx7d-pico-pi.dts and hobbit board imx7d-pico-hobbit.dts
from Linux v5.1-rc1.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Import Linux 5.1-rc1 DT from 9e98c678c2d6 ("Linux 5.1-rc1") for the
meson-g12a-u200 board, the meson-g12a.dtsi and the corresponding bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvW07AAoJEB6zHgIOrC/Iu4QH/1REDOTrsZPydd2yD/O81vPs
RiLC8wP2J4UmqtMcNTLyvxlYwrzqoR5J6SYdyBNU/+cLEp/gdzEI+rjsfSV2uRX1
Qb4Pk2FiI503JVjegxsbJqzASfiEP7rIg3HM5431xbhYH22MW2FH6le6yrtNxjBh
m1WFjQYX1bpbGb6zue8TgyLIeN1IqWuqnH9kUHixUEan+xrpEhN239LDFjdvGbvC
BvYyMtDddmMt4YDzNjgX36us993kylGZp6JijR3zgUao7I/JGVZAJrxw8MHDTnVy
UKv3VI9F5bGLSvzqTVL2MFU6XtJW26v+niGLhGzlUhb3TTKrdKOicm3VF7tO+JU=
=MamK
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-b' of git://git.denx.de/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2019.07 cycle
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
Linux commit details about the sun50i-h6-beelink-gs1.dts sync:
"arm64: dts: allwinner: h6: Introduce Beelink GS1 board"
(sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193)
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SAMA5D2 ICP Board features the SAMA5D27 SoC,
together with QSPI Flash, Wilc3000 wireless device and
EtherCat support.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Fix broken build:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix broken build:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This commit provides update and renames the bk4r1.dts to vf610-bk4r1.dts
file with more on SoC HW description.
The pcm052.dts has been renamed to vf610-pcm052.dts as well.
Moreover, a new vf610-pcm052.drsi file has been introduced
to reuse the common code between devices based on Phytec's
pcm052 modules.
Ported from Linux kernel - v4.20 (tag)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
- Misc dts files sync'ed with Linux version (Chris)
- Orion watchdog fix (Chris)
- kwbimage changed to also support Marvell bin_hdr binary (Chris)
- Add DM support to enable CONFIG_BLK for sata_mv (Stefan)
- Enable BLK on multiple platforms (Stefan)
- Misc minor fixes to AXP theadorable board (Stefan)
- Correct logic for DM_SCSI + unconverted drivers check (stefan)
- Misc changes to kirkwood to enable DM_USB here (Chris)
- Change ahci_mvebu to enable usage on A38x (Baruch)
- Update the kirkwood entry in git-mailrc (Baruch)
- Misc minor improvements (turris, documentation) (Baruch)
- Enhance sata_mv to support Kirkwood as well (Michael)
- Add wdt command (Michael)
- Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG
board support (Chris)
This patch synchronizes U-boot DT with kernel one
This is based on https://patchwork.kernel.org/cover/10797115/
This patch adds initial support of STM32MP157 discovery boards:
- Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1).
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
and 512MB of DDR3. Several connections are available on this boards:
4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ...
- Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2).
This board is a "super-set" of stm32mp157a-dk1. A display panel (otm8009a)
and Murata wifi/BT combo is added.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This board was added to u-boot first but the Linux maintainers requested
a more descriptive name. Rename the file to match the Linux usage and
update the board defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The DB-XC3-24G4XG is a switch development board from Marvell. It can
either use and external CPU card such as the db-88f6820-amc or the
internal CPU that is integrated into the switch.
Add support for running U-Boot on the internal CPU and enable the USB,
SPI and NAND peripherals. For now this needs the bin_hdr from the
Marvell U-Boot for this board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Import Linux 5.0 DT from 1c163f4c7b3f ("Linux 5.0") for the
meson-gxl-s805x-libretech-ac board and the corresponding changes
in meson-gxl.dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds the device trees for p200 and p201 boards.
Synced from kernel 5.0.0
Commit: a667cb7a94d4 ("Merge branch 'akpm' (patches from Andrew)")
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip
AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage.
This patch adds support for this board including SPL support. Therefore
the AT91Boostrap is not needed on this platform any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Migrate the following options to CONFIG_DM:
CONFIG_DM_GPIO
CONFIG_DM_MMC
CONFIG_DM_ETH
CONFIG_DM_SERIAL
CONFIG_DM_USB
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Since commit 27cb7300ff ("Ensure device tree DTS is compiled"),
build succeeds irrespective of the correctness of Makefile.
In fact, you can compile any defconfig without adding any entry in
arch/*/dts/Makefile.
As a result, a lot of wrong code have been merged unnoticed.
I am going to revert that commit, and lots of hidden issues have
come to light:
[1] Typos
armada-3720-uDPU.dts, sun8i-a83t-tbs-a711.dts
use the extension ".dts" instead of ".dtb"
[2] DTB is associated to undefined CONFIG option
For example, mx6sllevk_defconfig defines CONFIG_MX6SLL, but
associates its device tree to CONFIG_MX6SL, which is undefined.
[3] Lots of entries are missing
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
[trini: add imx6ul pico dtbs]
Signed-off-by: Tom Rini <trini@konsulko.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd] to the ones
from kernel v4.20 (commit 8fe28cb58bcb2).
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Import liteSOM and liteboard dts files from Linux v4.20. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch adds new mini target for versal.
This configuration is very minimal in size which runs
from OCM. It contains support for mtest which can be
used for running DDR memory tests.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds mini eMMC configuration which has only
emmc0 and emmc1 functionalities and can run from small
amount of memory. This is required for memory constraint
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds initial support for micro-DPU (uDPU) board which is based on Armada-3720 SoC.
micro-DPU is the single-port FTTdp "distribution point unit" made by Methode Electronics
which offers complete modularity with replaceable SFP modules both for uplink and downlink
(G.hn over twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Luis Torres <luis.torres@methode.com>
Cc: Scott Roberts <scott.roberts@telus.com>
Cc: Paul Arola <paul.arola@telus.com>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcVG0IAAoJECaAFcEOcohNKVAIAJd3DN/qudcVQdkuvAGK6WIk
Umxkm6rxHwur7oU+wxvK1p1l/0YTFBeCfo15quH1DkSc/WIUnmBlLmDvqpGVmPmh
ydZNE9ZChn0OKRIaM6pKJr+3p155cQDe6Mgg2j/5CnNx28KxT+vu7EqZbZvbQPag
wcZEK6Z6E5jMVHVn2lbLgmsBPmY7ksX168IqpvzTxIj0a4J3n0DcJUnO4RBBS0Q2
PGEvFhTvigVWs6r6GL0gLn3VwnQX30xQlIuKKORPcdhjk97cJcS4+bRxdTENTKD9
j3+pgyl1n04O8sPONZS7pH3fvJwtC6SwnoxTYxGrvjedw1LxbyHG3cqcGDg/TJ8=
=ik3X
-----END PGP SIGNATURE-----
Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchip
u-boot-rockchip changes for 2019.04-rc1:
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
This adds support for the ASUS C201, a RK3288-based clamshell
device. The device tree comes from linus's linux tree at
3f16503b7d2274ac8cbab11163047ac0b4c66cfe. The SDRAM parameters
are for 4GB Samsung LPDDR3, decoded from coreboot's
src/mainboard/google/veyron/sdram_inf/sdram-lpddr3-samsung-4GB.inc
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
add DTS from linux tree commit
"47bfa6d9dc8c060bf56554a465c9031e286d2f80"
change for U-Boot:
switch to SPDX-license identifier.
Signed-off-by: Heiko Schocher <hs@denx.de>
In preparation of adding CONFIG_DM_MMC support use separate device
trees for raw NAND and eMMC devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis-devboard target to dtb makefile
- add dtsi file for Neutis N5 needs
- add config file for Neutis N5 Dev board
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: update proper commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This adds device tree for OMAP3 IGEP based boards and the DM_MMC driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:
- UART
- eMMC
- USB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add board support for Ficus EE board from Vamrs. This board utilizes
common Rock960 family support.
Following peripherals are tested and known to work:
* Gigabit Ethernet
* USB 2.0
* MMC
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
[Reworked based on common Rock960 family support]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add board support for Rock960 CE board from Vamrs. This board utilizes
common Rock960 family support.
Following peripherals are tested and known to work:
* USB 2.0
* MMC
This commit also adds DDR configuration for LPDDR3-2GiB-1600MHz which
is being used on the board.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This configuration is useful when you want to run small u-boot and
perform DDR memory test to make sure that DDR is properly configured.
It is use for board bringup because alternative u-boot memory tests is
quite good.
Configuration is running out of OCM.
As is done for others mini configurations 0x80 bytes for variables is
enough and only default variables are stored there.
Alternative memtest is enabled and also 2GB of DDR via DTS files.
Configuration is enabling ZYNQMP_PSU_INIT_ENABLED and include psu_init()
from zcu102 for testing purpose.
In case of size issue this can be moved to SPL configuration as is done
for mini_qspi configuration but it is not a problem now.
Log:
U-Boot 2018.11-00268-gbd58b8ba8915 (Nov 29 2018 - 15:33:35 +0100)
Model: ZynqMP MINI
Board: Xilinx ZynqMP
DRAM: WARNING: Initializing TCM overwrites TCM content
2 GiB
EL Level: EL3
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds device tree for MT7623 development board - Bananapi R2
Detailed hardware information for BPI-R2 which could be found on
http://wiki.banana-pi.org/Banana_Pi_BPI-R2.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds MT7629 device tree and the includes it needs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import chiliSOM and chiliboard dts files from Linux v4.19. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Synchronize the Amlogic AXG Device Tree files and bindings include from
the recent Linux 4.20-rc1, because it includes patches fixing support for
U-boot.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SolidRun Clearfog GT-8K is based on Armada 8040.
https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k
The config file is identical to the Macchiatobin one
(mvebu_mcbin-88f8040_defconfig) with only the default device-tree
changed.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pinebook is a laptop produced by Pine64, with USB-connected keyboard,
USB-connected touchpad and an eDP LCD panel connected via a RGB-eDP
bridge from Analogix.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Banana Pi M2 Zero is a board by Sinovoip with Allwinner H2+ SoC, 16-bit
512MiB DDR3 memory, a MicroSD slot, two MicroUSB ports (one OTG and one
powering-only) and a miniHDMI port.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[jagan: Fixed board MAINTAINERS file]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Build the -u-boot variants of the device trees so they can be included
in Multi-DTB fitImage, which in turn allows us to build single U-Boot
image for multiple boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Xilinx DLC20 has I2C0 with EEPROM(1KB), UART1, GPIO, SD0 (EMMC 4GB),
USB0 device, ENET0, QSPI (16MB) and DDR(two of 256MB each).
Boards have mix of Winbond/ST QSPIs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds Device Tree for the Khadas VIM2 board.
The meson-gxm-khadas-vim2.dts is synchronized from Linux 4.18.10.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
For at91family, makefile was building unwanted DTBs
Moved them under specific target configuration.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add the board DTS files for 14x14 EVK and 9x9 EVK. They are necessary
for converting to use u-boot DM driver.
Two -u-boot.dtsi are added to modify compatible string of SPI flash
device to "spi-flash".
Signed-off-by: Ye Li <ye.li@nxp.com>
On iMX7D SabreSD board, the QSPI has pins conflict with EPDC (default).
To use QSPI, users have to rework the board (de-populate R388-R391, R396-R399
populate R392-R395, R299, R300). So we add new DTS file and new defconfig
dedicated for QSPI.
Other changes to support the DM QSPI:
- Add QSPI node and alias spi0.
- Modify spi4 (spi-gpio) node and add alias spi5 for it to avoid req
conflict
- Add EPDC node in imx7d.dtsi and disable it in imx7d-sdb-qspi.dts to
align with kernel and also present the conflict.
- Add -u-boot.dtsi to modify compatible string of mx25l51245g@0 to
"spi-flash"
- Remove iomux settings of qspi in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Avnet Ultra96 is rebranded Xilinx zcu100 revC/D. Add new defconfig files
and point to origin internal board name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.
Add support for it.
The device tree is from Linux next-20180720.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add support of stm32mp157c-ev1, the evaluation board with pmic stpmu1
(ev1 = mother board + daughter ed1) with device tree.
EV1 is the selected board by default in basic defconfig.
PS: CONFIG_PINCTRL_FULL activation avoid to increase
SYS_MALLOC_F_LEN (Early malloc usage: 2034)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of internal memory. This
configuration has only required qspi flash support and it
uses DCC as serial.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint OCM memory. This configuration
only has required parallel nor flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of memory. This configuration
has only required nand flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When the defconfig for the SoPine baseboard was added, there wasn't any
proper DT for the board yet, so we used the Pine64 DT as a placeholder.
Copy the DT file(s) meanwhile added in Linux over to U-Boot, and use
them in our defconfig.
This is as of v4.18-rc3, exactly Linux commit:
commit 7d556bfc49adddf2beb0d16c91945c3b8b783282
Author: Jagan Teki <jagannadh.teki@gmail.com>
Date: Mon Dec 4 10:23:07 2017 +0530
arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The various Aries Embedded boards have been orphaned for a year and no
one has come forward to take care of them. Remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
fdt_file is looking for imx6ul-geam-kit.dtb but Linux
has imx6ul-geam.dtb, since Linux skipped -kit on file name
by below commit.
"ARM: dts: imx6ul-geam: Skip suffix -kit from dts name"
(sha1: 182de5ebce71e469cfa686fcdf08c9cbe11ece97)
So, due to this mismatch U-Boot failed to pick the
proper dtb which eventually break the Linux boot.
This patch fixed this mismatch by
- renaming dts files
- update config option to use new dtb file
- update fdt_file to new dtb file name
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Orange Pi Zero Plus is an open-source single-board computer
using the Allwinner H5 SOC.
H5 Orangepi Zero Plus has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot
- 16MBit SPI Nor flash
- Debug TTL UART
- 1GBit/s Ethernet (RTL8211E)
- Wifi (RTL8189FTV)
- USB 2.0 Host
- USB 2.0 OTG + power supply
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.
H2+ Orange Pi R1 has
- Quad-core Cortex-A7
- 256MB DDR3
- micrSD slot
- 128MBit SPI Nor flash
- Debug TTL UART
- 100MBit/s Ethernet (H2+)
- 100MBit/s Ethernet (RTL8152B)
- Wifi (RTL8189ETV)
- USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch splits the current mini emmc configuration into emmc0
and emmc1 configurations because emmc is probed at boot time and on
systems which have only one interface mini configuration is failing on
unused interface. This patch also adds required clock node in dts and
enables CONFIG_MMC_SDHCI_ZYNQ through defconfig.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The helios4 is built on the SolidRun Armada 38x SOM.
The port os based on the ClearFog board, using information from
https://github.com/helios-4/u-boot-marvell as well as dtb input
from https://github.com/helios-4/linux-marvell
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
Basic support for the Renesas Ebisu board based on R-Car E3:
- Memory,
- Main crystal,
- Serial console,
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[shimoda: rebase and add SPDX-License-Identifier]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Sort the Makefile entries, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
This adds basic support for the Turris Mox board from CZ.NIC, which is
currently being crowdfunded on Indiegogo.
Turris Mox is as modular router based on the Armada 3720 SOC (same as
EspressoBin).
The basic module can be extended by different modules. The device tree
binary for the kernel can be dependent on which modules are connected,
and in what order. Because of this, the board specific code creates
in U-Boot a variable called module_topology, which carries this
information.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs out of DDR with default configuration that's why
DDR needs to be partitioned if there is something else running on arm64.
Console is done via Cadence uart driver and the first Cadence Triple
Timer Counter is used for time.
This configuration with uart1 was tested on zcu100-revC.
U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200)
Model: Xilinx ZynqMP R5
DRAM: 512 MiB
WARNING: Caches not enabled
MMC:
In: serial@ff010000
Out: serial@ff010000
Err: serial@ff010000
Net: Net Initialization Skipped
No ethernet found.
ZynqMP r5>
There are two ways how to run this on ZynqMP.
1. Run from ZynqMP arm64
tftpb 20000000 u-boot-r5.elf
setenv autostart no && bootelf -p 20000000
cpu 4 disable && cpu 4 release 10000000 lockstep
or
cpu 4 disable && cpu 4 release 10000000 split
2. Load via jtag when directly to R5
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables support zc1275 revB board. It has
SD added compared to revA. The same configuration will
work for RevC boards aswell.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Banana Pi BPI-M2 Berry is a quad-core mini single board computer
built with Allwinner V40 SoC. It features
- Quad Core ARM Cortex A7 CPU V40
- 1GB of RAM .
- microSD/SATA port..
- onboard WiFi and BT
- 4 USB A 2.0 ports
- 1 USB OTG port
- 1 HDMI port
- 1 audio jack
- DC power port
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The dts Makefile entries for the H3 are not ordered correctly.
Move the Nano Pi entries before the Orange Pi so they are.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds a device tree file for the H5 version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe2754412 ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H5 SoC, and
has 4Gb DDR3 chips instead of 2Gb ones.
The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds a device tree file for the H2+ version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe2754412 ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H2+ SoC, and
has only two 2Gb DDR3 chips instead of four.
The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for zc12xx boards. All of them are internal boards for
silicon validation and share very similar base platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With U-boot runtime board detect for DTB selection a "default" dtb needs
to be created. This will be used temporarily until the "proper" dtb is
selected.
Also, add -u-boot.dtsi for AM437x SK and IDK to enable I2C for
board detection via DM_I2C.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Sync DTS from Linux and add FDT support for AT91 ma5d4evk board.
usb0, usb1, usb2 and hlcdc_pwm nodes removed, since there is no support it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync DTS from Linux and add FDT support for AT91 vinco board.
usb0, usb1, and usb2 nodes removed, since there is no support it.
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add minimal devicetree for STM32MP157C-ED1 board,
with only the devices to allow boot from SDCARD:
- RCC for clock and reset
- UART4 for console
- I2C and PMIC
- DDR
- SDMMC0 for SDCard
Waiting Kernel upstream for alignment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This board offers:
_ STM32F746NGH6 microcontroller with 1 Mbyte Flash and 320+4 Kbytes RAM
_ Six 5 V power supply options:
Power jack
ST-LINK/V2-1 USB connector
User USB HS connector
User USB FS1 connector
User USB FS2 connector
Daughterboard
_ SAI Audio DAC, stereo audio jack which supports headset with microphone
_ Stereo digital microphone, audio jack connector used to connect
external speakers
_ 2 Gbytes (or more) SDMMC interface microSD card
_ RF-EEPROM on I2C compatible serial interface
_ RS-232 communication
_ IrDA transceiver
_ JTAG/SWD and ETM trace debug support, ST-LINK/V2-1 embedded
_ IEEE-802.3-2002 compliant Ethernet connector
_ Camera module
_ 8Mx32 bit SDRAM, 1Mx16 bit SRAM & 8Mx16 bit Nor Flash
_ 512 Mbits QuadSPI Nor Flash
_ 5.7 inch 640x480 pixel TFT color LCD with capacitive touch panel
_ Joystick with 4-direction control and selector
_ Reset, WakeUp/Tamper or key button
_ 4 color user LEDs
_ Extension connectors & memory connectors for daughterboard or
wrapping board
_ USB OTG HS and FS with Micro-AB connectors
_ RTC with backup battery
_ CAN 2.0A/B compliant connection
_ Potentiometer
_ Motor control connector
More detailed information are available here :
http://www.st.com/en/evaluation-tools/stm32746g-eval.html
To compile stm32f746-eval board, use same defconfig as
stm32f746-disco, the only difference is to pass
"DEVICE_TREE=stm32746g-eval".
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
A20-SOM204 board has option with onboard 16GB eMMC. The chip is wired
to MMC2 slot.
This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This is new System-On-Module platform with universal dimm socket for
easy insertation. The EVB board is designed to be universal with
future modules.
Base features of A20-SOM204 board includes:
* 1GB DDR3 RAM
* AXP209 PMU
* KSZ9031 Gigabit PHY
* AT24C16 EEPROM
* Status LED
* LCD connector
* GPIO connector
There will be variants with the following options:
* Second LAN8710A Megabit PHY
* 16MB SPI Flash memory
* eMMC card
* ATECC508 crypto device
The EVB board has:
* Debug UART
* MicroSD card connector
* USB-OTG connector
* Two USB host
* RTL8723BS WiFi/BT combo
* IrDA transceiver/receiver
* HDMI connector
* VGA connector
* Megabit ethernet transceiver
* Gigabit ethernet transceiver
* SATA connector
* CAN driver
* CSI camera
* MIC and HP connectors
* PCIe x4 connector
* USB3 connector
* Two UEXT connectors
* Two user LEDs
Some of the features are multiplexed and cannot be used the same time:
CAN and Megabit PHY. Others are not usable with A20 SoC: PCIe and USB3.
This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel, except some nodes are removed to make file
compatible with existing dtsi file.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add R8A77965 M3N Salvator-XS development kit support. This kit is
similar to the other Salvator-X(S) ones, except is has M3N SoC on
it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for a new boards from devboards.de , the DBM-SoC1 .
This board has one ethernet port, one USB OTG port and USB UART.
Signed-off-by: Marek Vasut <marex@denx.de>
Engicam Is.IoT has eMMC and NAND cpu modules where MMC
is common for both, so remove explicit mmc defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
This patch adds support for Quad/Dual and DualLite/Solo SOM's on
MIPI starter kit with boot from SD and eMMC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
This patch adds new target which is called as mini configuration
with only emmc functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
emmc support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new target which is called as mini configuration
with only nand functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
nand support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This DT file comes from kernel v4.15, this board offers :
_ STM32F429NIH6 microcontroller
_ 4.3” color TFT LCD with resistive touchscreen (480 x 272 pixels)
_ Six 5 V power supply options:
Power jack
ST-LINK/V2 USB connector
User USB HS connector
User USB FS1 connector
User USB FS2 connector
Daughterboard
_ SAI Audio DAC, stereo audio jack which supports headset with
microphone
_ Stereo digital microphone, audio terminal connector used to connect
external speakers
_ 2 GBytes (or more) SDIO interface MicroSD card
_ RF EEPROM on I2 C compatible serial interface
_ RS-232 communication
_ IrDA transceiver
_ JTAG/SWD and ETM trace debug support, ST-LINK/V2 embedded
_ IEEE-802.3-2002 compliant Ethernet connector
_ Camera module
_ 8M x 32-bit SDRAM, 1M x 16-bit SRAM and 8M x 16-bit NOR Flash
_ Joystick with 4-directional control and selector
_ Reset, Wakeup and Tamper buttons
_ 4 color user LEDs
_ Extension connectors & memory connectors for daughterboard or
wrapping board
_ USB OTG HS and FS with Micro-AB connectors
_ RTC with backup battery
_ CAN2.0A/B compliant connection
_ Potentiometer
_ Motor control connector
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This commit adds OMAP3 BeagleBoard devicetree files from
Linux v4.15-rc5. This includes standard OMAP34XX board revisions as
well as the 'xM' which is OMAP36XX.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
This commit adds support for 96Boards Dragonboard820C.
The board is based on APQ8086 Qualcomm Soc, complying with the
96Boards specification.
Features
- 4x Kyro CPU (64 bit) up to 2.15GHz
- USB2.0
- USB3.0
- ISP
- Qualcomm Hexagon DSP
- SD 3.0 (UHS-I)
- UFS 2.0
- Qualcomm Adreno 530 GPU
- GPS
- BT 4.2
- Wi-Fi 2.4GHz, 5GHz (802.11ac)
- PCIe 2.0
- MIPI-CSI, MIPI-DSI
- I2S
U-Boot boots chained from LK (LK implements the fastboot protocol) in
64-bit mode.
For detailed build instructions see readme.txt in the board directory.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This DT file comes from kernel v4.15-rc1
stm32f469-pinctrl.dtsi header has been updated with correct
STMicroelectronics Copyright.
Remove the paragraph about writing to the Free Software
Foundation's mailing address as requested by checkpatch.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
All these files comes from kernel v4.15-rc1.
Update some header with correct STMicroelectronics Copyright.
Remove the paragraph about writing to the Free Software
Foundation's mailing address as requested by checkpatch.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H3 SoC.
The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.
Raspberry Pi B+ like peripherals supported on this board include:
- Power input through micro-USB connector (without USB OTG)
- Native 100 Mbps ethernet using the internal PHY, as opposed to
USB-based on the RPi
- 4x USB 2.0 host ports, directly connected to the SoC, as opposed to
being connected through a USB 2.0 hub on the RPi
- TV and audio output on a 3.5mm TRRS jack
- HDMI output
- Micro-SD card slot
- Standard RPi B+ GPIO header, with the standard peripherals routed to
the same pins.
* 5V, 3.3V power, and ground
* I2C0 on the H3 is routed to I2C1 pins on the RPi header
* I2C1 on the H3 is routed to I2C0 pins on the RPi header
* UART1 on the H3 is routed to UART0 pins on the RPi header
* SPI0 on the H3 is routed to SPI0 pins on the RPi header,
with GPIO pin PA17 replacing the missing Chip Select 1
* I2S1 on the H3 is routed to PCM pins on the RPi header
- Additional peripherals from the H3 are available on different pins.
These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3
In addition, there are a number of new features:
- Console UART header
- Consumer IR receiver
- Camera interface (not compatible with RPi)
- Onboard microphone
- eMMC expansion module port
- Heatsink mounting holes
This patch adds defconfig and dts files for this board. The dts file is
the same as the one submitted for inclusion in Linux, with some minor
revisions to match the dtsi file and old EMAC bindings in U-boot.
Since the OTG controller is wired to a USB host port, and the H3 has
proper USB hosts to handle host mode, the MUSB driver is not enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This commit adds OMAP3 EVM devicetree files from Linux v4.15-rc3. Note
that this is the first addition of OMAP34XX devicetree files.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Add bits to support yet another board, the R8A77995 D3 Draak.
The DT file is from Linux 4.15-rc1 , commit
b35334447513c14a4dd55a67c269a743d4a4824b .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another board, the R8A77970 V3M Eagle.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The TBS Tablet sports an LVDS display, an eMMC, an external SD, USB devices
and USB OTG.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds platform code for the Khadas VIM board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-khadas-vim.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds platform code for the Libre Computer CC "Le Potato" board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-libretech-cc.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add dts binding header for rk3128, files origin from kernel.
Series-Changes: 2
- fix i2c address
- add saradc and usb phy node
- emmc using fifo mode for there is no dma support in rk3128 emmc
- add some clock id in cru.h
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add the SAMA5D2 PTC EK board and remove the SAMA5D2 PTC ENGI board
which was a prototype.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Add configuration files/dtses for mini u-boot configurations which runs
out of OCM.
ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE
0xfffc0000
+#define CONFIG_SYS_SDRAM_SIZE 0x40000
was hardcoded.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cc108 board is wiring uart via PL which is good platform for SPL fpga
support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board
contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports
booting from SD.
Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Michal Simek <monstr@monstr.eu>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5
In the preparation of the support of the Amlogic P212 board,
import the corresponding meson-gxl-s905x-p212.dts file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
The Banana Pi M2-Magic is a small board with an Allwinner A33, an eMMC, a
wifi chip and some pin headers. Enable support for it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The upstream (Linux) device tree file for the Bananapi M3 follows the
convention of using the well known brand name, instead of the vendor
name, for naming. The file was recently added to upstream in commit
359b5a1e1c2d ("ARM: sun8i: a83t: Add device tree for Sinovoip Bananapi
BPI-M3")
Rename the device tree file in U-boot to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This file is imported from linux kernel v4.13
Add device tree support for STM32H743 evaluation board.
This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS and FS
_ I2 C compatible serial interface
_ RTC with rechargeable backup battery
_ SAI Audio DAC
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM, 1Mx16bit SRAM and 8Mx16bit NOR Flash
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Potentiometer
_ 4 colored user LEDs
_ Reset, wakeup, tamper or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
Power jack
3 USB with Micro-AB
RS-232 communications
Ethernet RJ45
FD-CAN compliant connection
Stereo headset jack including analog microphone input
2 audio jacks for external speakers
microSD™ card
JTAG/SWD and ETM trace
_ Expansion connectors:
Extension connectors and memory connectors for daughterboard
or wire-wrap board
_ Flexible power-supply options: ST-LINK USB VBUS or external
sources
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All these files are imported from linux kernel v4.13
Add device tree support for STM32H743 SoC and discovery
board. This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS
_ I2 C compatible serial interface
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Reset, wakeup, or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
1 USB with Micro-AB
Ethernet RJ45
Stereo headset jack including analog microphone input
microSD™ card
RCA connector
JTAG/SWD and ETM trace
_ Expansion connectors:
Arduino Uno compatible Connectors
2 x PIO connectors (PMOD and PMOD+)
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for Vyasa RK3288 initial board
from Amarula Solutions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The SAMA5D27-SiP (System in Package) integrates the SAMA5D2
with 1Gbit DDR2-SDRAM in a single package.
The SAMA5D27 SOM1 embeds a 64Mbit QSPI flash, KSZ8081 Phy and
Mac-address EEPROM.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for selecting proper dtb for
dra76x u-boot from FIT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.
OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or 2GB RAM DDR3L @ 672Mhz
- microSD slot and 4/8/16GB eMMC
- Debug TTL UART
- HDMI
- LCD
- IR receiver
- 5V DC power supply
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.
Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The RK3368-uQ7 (codenamed 'Lion') is a micro-Qseven (40mm x 70mm,
MXM-230 edge connector compatible with the Qseven specification)
form-factor system-on-module based on the octo-core Rockchip RK3368.
It is designed, supported and manufactured by Theobroma Systems.
It provides the following features:
- 8x Cortex-A53 (in 2 clusters of 4 cores each)
- (on-module) up to 4GB of DDR3 memory
- (on-module) SPI-NOR flash
- (on-module) eMMC
- Gigabit Ethernet (with an on-module KSZ9031 PHY)
- USB
- HDMI
- MIPI-DSI/single-channel LVDS (muxed on the 'LVDS-A' pin-group)
- various 'slow' interfaces (e.g. UART, SPI, I2C, I2S, ...)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the configuration files to support the device tree and driver
model. The peripheral clock and pins configuration are handled by
the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.12-rc6,
commit 6f7da290413ba713f0cdd9ff1a2a9bb129ef4f6c . This includes both M3
and H3 ULCB and Salvator-X boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not using board revision is causing confusion about which board is
supported and tested. Mark dts files exactly with board revision which
was tested. When new board revision arives it can be symlink if SW view
is the same. Also add -revX suffix to compatible string because user space
tools are parsing this string and can change behavior depends of board
revision.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Z-Turn board is a low cost development board based on the
Xilinx Zynq SoC. While it's powerful and quite versatile, it
so far lacked upstream support.
This patch adds basic support for the Z-Turn. It does however
for now miss enablement for MIO51 reset which means that USB
and ethernet don't work. For that either FSBL or SPL need to
be adjusted. The SPL part will follow later.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add basic DT support for K2G ICE evm. Only minimal peripherals are
supported to allow console output and MMC boot.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With U-boot runtime board detect for DTB selection a "default" dtb needs
to be created. This will be used temporarily until the "proper" dtb is
selected.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add initial device tree support for LD20 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add initial device tree support for LD11 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The topic-miamilite SoM contains a Zynq xc7z010 SoC, 1GB DDR3L RAM,
64MB dual-parallel QSPI NOR flash and clock sources.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
NanoPi NEO2 is designed and developed by FriendlyElec
using the Allwinner 64-bit H5 SOC.
NanoPi Neo2 key features
- Allwinner H5, Quad-core 64-bit Cortex-A53
- 512MB DDR3 RAM
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC MicroUSB power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.
A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Whistler is an ancient Tegra 2 reference board. I may have been the only
person who ever used it with upstream software, and I've just recycled
the board hardware. Hence, it makes sense to remove support from software.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.
NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
This adds the DDR3-1866 timing via its own DTS and wires it up. This
(currently) is not the default timing for the RK3399-Q7 and should be
selected explicitly via the config (CONFIG_DEFAULT_DEVICE_TREE).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds the DDR3-1333 timing via its own DTS and wires it up. This
is not the default timing for the RK3399-Q7 and should be selected
explicitly via the config (CONFIG_DEFAULT_DEVICE_TREE).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
To better support different RAM timings (DDR3-1333 and DDR3-1866 are
assembly options for the RK3399-Q7), this refactors the DTS support
and renames the default DTS variant from rk3399-puma to
rk3399-puma-ddr1600:
- changes the rk3399-puma DTS into a board-specific DTSI by removing
the inclusion of the DRAM timings
- adds a new rk3399-puma-ddr1600.dts, which includes the (new) common
board DTSI and the DDR3-1600 timing DTSI
- wires this up from arch/arm/dts/Makefile and configs/puma-rk3399_defconfig
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add basic support for rv1108 evb, whith this patch we
can boot into u-boot console.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI / BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GeekBox is a TV box from GeekBuying, based on an MXM3 module.
The module can be used with base boards such as the GeekBox Landingship.
This adds basic support to chain-load U-Boot from Rockchip's miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sheep board is designed by Rockchip as a EVB for rk3368.
Currently it is able to boot a linux kernel and system
to console with the miniloader run as fist level loader.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT
Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology
CPU: Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.
BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 SDRAM with 733MHz
- MicroSD/eMMC(8GB)
- 10/100/1000Mbps ethernet (Realtek RTL8211E/D)
- Wifi + BT
- IR receiver
- Audio In/Out
- Video In/Out
- 5V 2A DC power-supply
For dts file,
Sync with Linux commit 4879b7ae("Merge tag 'dmaengine-4.12-rc1'").
Boot from MMC:
-------------
U-Boot SPL 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
NOTICE: Configuring AXP PMIC
NOTICE: PMIC: setup successful
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31 +0000) Allwinner Technology
CPU: Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
NanoPi M1 is a board based on Allwinner H3 CPU.
This commit adds the support for this platform with:
- an include device tree which enables UART, LEDs, GPIO key switch,
1 USB host ports and the SD-card as a dtsi file.
- a device tree specific to this board that enables the
2 additional USB ports
- a defconfig file for minimal support
- a section in MAINTAINERS (add myself)
Synchronized with the kernel device tree, from commits:
sun8i-nanopi.dtsi: 85d2913614d9ab899d23b7ab7d22d23cf45bd1de
sun8i-h3-nanopi-m1.dts: 10efbf5f16336b7540ad6a16aa1cb0b26bab033b
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Firefly-rk3399 is a bord from T-Firefly, you can find detail about
it here:
http://en.t-firefly.com/en/firenow/Firefly_RK3399/
This patch add basic node for the board and make it able to bring
up.
Peripheral/interfaces on board:
- usb hub which connect to ehci controller;
- UART2 debug
- eMMC
- PCIe
- USB 3.0 HOST, type-C port
- sdio, sd-card
- HDMI
- Ethernet
- OPTICAL
- WiFi/BT
- MIPI CSI/DSI
- IR
- EDP/DP
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch also removes all the excessive code for NS16550 intiailization
as the device tree can do that now. This also adds DM_I2C and DM_MMC
since the overlying drivers have the built-in support already. The
corresponding include/config/omap3_logic.h also reduced in size
due to the new device tree support.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Retain Auto-detect ability between SOM-LV and Torpedo
Split this off from the device sub submissions
The device tree source files of at91sam9263ek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9rlek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9g20ek and at91sam9260ek
boards are copied from the Linux v4.10, do the changes below.
- Fix the build error for the usb0 node.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Add the clk pinctrl of the mmc0 node.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9m10g45ek boards are copied
from the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9n12ek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the pinctrl-names of mmc0 node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9x5ek board are copied from
the Linux v4.10, do the changes below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add NAND to CP master device tree. Add armada-7040-db-nand
device tree for the board configured with NAND boot device.
Add comment about boot device ID to armada-7040-db DTS.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This board support stm32f7 family device stm32f769-I with 2MB internal Flash &
512KB RAM.
STM32F769 lines offer the performance of the Cortex-M7 core (with double
precision floating point unit) running up to 216 MHz.
To compile for stm32f769 board, use same defconfig as stm32f746-disco,
the only difference is to pass "DEVICE_TREE=stm32f769-disco".
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Add support for the Terasic DE10-Nano board. The board
is based on the DE0-Nano-Soc board but adds a larger FPGA
and an HDMI output.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.
This patch add barebone dtsi/dts files for the R40 and Bananapi M2 Ultra,
as well as a defconfig for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Somehow 43b5c78d8d ("rockchip: cosmetic: Sort RK3288 boards") moved
the rock board in between some rk3288 board, probably as a result of
rebasing.
So move it back to its original position above all rk3288 boards.
Fixes: 43b5c78d8d ("rockchip: cosmetic: Sort RK3288 boards")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Add the device tree file for sama5d4ek board.
The dts file is copied from Linux-4.4, do the following changes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree files for sama5d4 Xplained board.
The dts files are copied from Linux-4.4, do the following changes.
- add reg property for pinctrl node.
- move the gpio nodes(pioA, pioB, pioC ...) from the pinctrl child's
nodes to its slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree file for sama5d3 Xplained board.
The dts files are copied from the Linux-4.9, do changes as below.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree files for sama5d3xek board.
The dts files are copied from Linux-4.9, do the changes as below.
- add reg property for the pinctrl node.
- move the gpio nodes (pioA, pioB, pioC ...) as the pinctrl's
slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
- add spi0 node aliases.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash. The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM. Items in the dtsi file
are specific to the SOM itself. Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
The Sunchip CX-A99 is a board used in some media players. It features:
An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores)
2 GiB or 4 GiB DDR3 DRAM
AXP808 PMIC
16 GB or 32 GB eMMC
SDIO Wifi/Bluetooth/FM module
SD card slot
1 USB 3.0 connector
2 USB 2.0 connectors
SATA connector
UART connector (internally) for serial console
Ethernet connector (10/100/1000 Mbit/s)
HDMI connector
Composite video and analog audio connector
S/PDIF connector
IR remote control receiver
This patch adds a defconfig for the board. The DRAM settings are as found
in the vendor sys_config.fex file.
It has a preliminary device tree for use until a device tree is accepted
upstream, after which it can be replaced by the upstream version.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
[squash commits, and edited new meanful commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Those DT will be part of 4.10, sync them so we can have our own config.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Add support for the NanoPi NEO Air H3 board from friendlyarm.com . This
board contains WiFi, Bluetooth, 8GB eMMC storage and 512 MB DDR3 ram.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rebase on master]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The OrangePi PC 2 is a typical SBC with the 64-bit Allwinner H5 SoC.
Add a (64-bit only) defconfig defining the required options to build
the U-Boot proper.
Create a new .dts file for it by including the (32-bit) H3 SoC .dtsi
and changing the differing components accordingly.
This is a preliminary device tree mostly for U-Boot's own sake, it
is expected to be updated once the official DT gets accepted upstream.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[squash the commits, update the commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
expansion ports.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Sort rk3288 boards in alphabetical order.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399-Q7 is a system-on-module featuring the Rockchip RK3399
in a Qseven-compatible form-factor.
These changes add a device-tree describing the board and its
interfaces for basic functionality (e.g. GbE, SPI, eMMC, SD-card).
This includes the following changes from the original development:
* dts: rk3399-puma: include DTS for RK3399-Q7 SoM in the Makefile
* dts: rk3399-puma: add gmac for the RK3399-Q7
This change enables the Gigabit Ethernet support on the RK3399-Q7.
* dts: rk3399-puma: use serial0 for stdout
* dts: rk3399-puma: prepare the sdmmc node for SPL booting
* dts: rk3399-puma: enable spi1 and spi5, add /spi1/spiflash
The RK3399-Q7 (Puma) unsually (this is a build-time option for
customised boards) has an on-module SPI-flash connected to SPI1.
As of today, this is a Winbond W25Q32DW (32MBit) device.
The SPI5 controller is routed to the Q7 edge connector and provides
general-purpose SPI connectivity for customer base-boards.
With some minor improvements on integration into our outbound tree
- explicitly modelled the SPI flash as 'spiflash' under spi0
[dts: rk3399-puma: explicitly model spi-flash under spi1]
- renamed the aliases to spi0 and spi1 to allow easier use of
commands and legacy (SPL) infrastructure... i.e. the controllers
will be 0 and 1 for 'sf probe', 'sspi', etc.
[dts: rk3399-puma: rename aliases to number spi as 0 and 1 for commands]
* dts: rk3399-puma: include SPI in the spl-boot-order property
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Rock is a RK3188 based single board computer by Radxa.
Currently it still relies on the proprietary DDR init and
cannot use the generic SPL, but at least is able to boot
a linux kernel and system up to a regular login prompt.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix sort order in defconfig, enable CONFIG_SPL_TINY_MEMSET:
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds board support for the Toradex Apalis TK1 a computer on
module which can be used on different carrier boards.
The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot, environment storage and Toradex factory config block
- Gigabit Ethernet
- MMC/SD cards (both MMC1 as well as SD1 slot)
- USB client/host (dual role OTG port as client e.g. for DFU/UMS or host,
other two ports as host)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added A8040 dts file for community board MACCHIATIBin.
The patch includes the following features:
AP - Serial console (connected to onboard FTDI usb to serial)
CP0 - PCIe x4, SATA, I2C and 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy)
CP1 - Boot SPI, USB3 host, 2xSATA, 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy),
SGMII connected to onboard 1512 1Gbps copper phy,
and additional SGMII connected to SFP
(default 1Gbps can be configured to 2.5Gbps).
Network interface naming -
egiga0 - CP0 KR
egiga1 - CP1 KR
egiga2 - CP1 RJ45 1Gbps connector (recommended for TFTP boot)
egiga3 - CP1 SFP default 1Gbps and can be modified to 2.5Gbps
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Introduce device tree support.
dts from kernel commit c4f3f22edd Merge tag 'linux-kselftest-4.11-rc1'
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.
U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1
U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)
CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Boot from MMC:
-------------
U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33)
Trying to boot from MMC1
U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100)
CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 33C
Reset cause: POR
Model: Engicam Is.IoT MX6UL Starterkit
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
isiotmx6ul>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add dts binding header for rk3328, files origin from kernel.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
This device tree has been extracted from v4.9 kernel
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Miniarm is the internal project code. Now it is officially named Tinker board.
So rename it.
Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As reported in [1], rename the k2* dts files to keystone-* files
this will force consistency throughout.
Script for the same (and hand modified for Makefile and config
files):
for i in arch/arm/dts/k2*
do
b=`basename $i`;
git mv $i arch/arm/dts/keystone-$b;
sed -i -e "s/$b/keystone-$b/g" arch/arm/dts/*[si]
done
This is similar to linux kernel commit 5edafc29829bc ("ARM: dts: k2*: Rename
the k2* files to keystone-k2* files")
[1] http://marc.info/?l=linux-arm-kernel&m=145637407804754&w=2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds the DTS source files needed for stm32f746-disco board
The files are based on the stm32f429/469 files from current linux
kernel.
Source for "arch/arm/dts/armv7-m.dtsi": Linux: "arch/arm/boot/dts/armv7-m.dtsi"
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
All the UniPhier DT files are compiled if CONFIG_ARCH_UNIPHIER
is enabled, but not all of them actually work. For example, when
U-Boot is compiled for ARM 32 bit, 64 bit DT files are also built,
and vice versa. Compile only the combination that makes sense.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a proper device tree file for Orange Pi Zero boards from Xunlong,
which come with a Allwinner H2+ SoC (similar to H3).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Add CycloneV based Terasic DE1-SoC board. The board boots
from SD/MMC. Ethernet and USB host is supported.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marex@denx.de>
This patch adds the necessary files to support the Marvell Armada 8k
devel board. Most board specfic files are shared with the Armada 7k
boards under the name "armada-8k*". So only minimal changes are
necessary to add this basic board support (except the DT files of
course).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Add DT support for dra71-evm and built it as part of FIT image.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds device trees for the bcm283x platform to be used with
OF_CONTROL. The version 4.8-rc7 of the linux kernel was used as source.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add board support for sun8i_r16 Nintendo NES Classic edition.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
[jagan: Add commit message body]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This adds support for the Asus Chromebook Flip, an RK3288-based clamshell
device which can flip into 'tablet' mode. The device tree file comes from
Linux v4.8. The SDRAM parameters are for 4GB Samsung LPDDR3.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds support for the Asus Chromebit, and RK3288-based device designed
to plug directly into an HDMI monitor. The device tree file comes from
Linux v4.8.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have a single rk3288-based Chromebook: chromebook_jerry. But
all such Chromebooks can use the same binary with only device-tree
differences. The family name is 'veyron', so rename the files accordingly.
Also update the device-tree filename since this currently differs from
Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
The patch adds support for Freescale ls1021a-iot board.
Signed-off-by: Feng Li <feng.li_2@nxp.com>
[YS: rewrite commit message, fix whitespace in Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
The topic-miami SoMs contain a Zynq xc7z015 or xc7z030 SoC, 1GB DDR3L RAM,
32MB QSPI NOR flash and 256MB NAND flash.
The topic-miamiplus SoMs contain a Zynq xc7z035, xc7z045 or xc7z100 SoC,
2x 1GB DDR3L RAM, 64MB dual-parallel QSPI flash, clock sources
and a fan controller.
The "Florida" carrier boards add SD, USB, ethernet and other interfaces.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
i.CoreM6 Quad/Dual modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DQ, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DL, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add base device for NXP i.MX 7Solo/7Dual. The two SoC are very
similar and hence can share the same device tree for boot loaders
purpose.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.
Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)
CPU: Freescale i.MX6ULL rev1.0 at 396MHz
CPU: Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM: 512 MiB
MMC: initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch integrates the Armada 7K/8K dts files from the latest
submission on the linux-arm-kernel mailing list.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch integrates the Armada 3700 dts files from the latest
submission on the linux-arm-kernel mailing list.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This board is a plug in card for Marvell's switch system development
kits. Form-factor aside it is similar to the DB-88F6820-GP with the
following differences.
- TCLK is 200MHz
- SPI1 is used
- No SATA
- No MMC
- NAND flash
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The NanoPi NEO is a simple h3 board with 512MB RAM, ethernet, one usb
and one usb OTG connector.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
LS1046AQDS Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
SATA:
* SerDes2 Lane3 to SATA port
USB 3.0: one super speed USB 3.0 type A port
one Micro-AB port
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.
The dts file is identical to the one submitted to the upstream kernel,
except that it has the pending patch to enable the ethernet controller
squashed in, as u-boot already has sun8i-emac support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A33-OLinuXino is A33 development board designed by Olimex LTD.
It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.
It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a proper dts for the iNet D978 rev2 based A33 tablets.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Colorado TK1 SOM is a small form factor board similar to the
Jetson TK1. The main differences lie in the pinmux, and in that the
PCIe controller is set to use in 4lanes+1lane, rather than 2+2.
The pinmux header here was generated from a spreadsheet provided by
Colorado Engineering using the tegra-pinmux scripts. The spreadsheet
was converted from v09 to v11 by me.
Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The board ID EEPROM and board ID stickers on p2771-0000 will use a numeric
versioning scheme, with version numbers such as 000/100/200/300/400/500.
Within NVIDIA, these versions are also known as A00/A01/A02/A03/A04/B00.
However, that numbering scheme is not easily visible outside of NVIDIA,
and so does not make much sense to use. Convert U-Boot to use the readily
visible numeric scheme.
Also, it turns out that the current A02 DT actually applies to board
versions 000/100/200 (A00..A02). Consequently rename this to 000 not 200
so that all U-Boot builds are named after the first version of the HW they
support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a defconfig and dts file for the Empire Electronix M712 tablet, this
is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on
the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Sync dts files with the current (Aug 18th 2016) state of Maxime's
linux/sunxi/for-next repo.
Note this commit also updates configs/MSI_Primo81_defconfig,
adding: "# CONFIG_REQUIRE_SERIAL_CONSOLE is not set", this is necessary
because the tablet does not have a reachable uart so the dts sync
drops its serial0 alias.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a defconfig and dts file for tablets using the generic inet-q972 PCB.
Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.
This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fennec is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes
on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access
to display pins, I2C, SPI, UART and GPIOs.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.
The upstream kernel devs have decided that they want a separate
dts for the PC Plus rather then sharing a single dts between the
regular PC and the PC Plus. So add a new orangepi_pc_plus_defconfig
to match.
The added dts file matches the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These files are from kernel upstream:
"649a371 Add linux-next specific files for 20160616"
with some modification need by U-Boot:
- chosen with stdout-path to uart2.
- add clock-frequency for uart2
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).
evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are multiple versions of p2771-0000 board. There are SW visible
incompatible differences between the versions, and they are relevant to
U-Boot. Create separate "A02" and "B00" defconfigs (named after the first
and/or only board rev the defconfig supports) so that users can select
which build they want.
With the minimal set of HW currently enabled in U-Boot, the differences
are irrelevant, hence the DT files aren't different. However, that will
change in a future patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
The DTS file is identical to the one submitted to the upstream kernel.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
add DM and DTS support for the at91 based siemens
boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
The dts file this commit adds is identical to the one submitted to
the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.
Fixes: 74cc8b097d ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This adds support for IS1 board. Pretty usual socfpga board,
256MB of RAM, does not have MMC, two SPI chips, one ethernet port, two
additional ethernet ports connected to the FPGA.
Signed-off-by: Pavel Machek <pavel@denx.de>
QorIQ LS1012A FREEDOM (LS1012AFRDM) is a high-performance
development platform, with a complete debugging environment.
The LS1012AFRDM board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Development System (LS1012AQDS) is a high-performance
development platform, with a complete debugging environment.
The LS1012AQDS board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for board based on the popular Altera Cyclone V SoC.
This board has the following properties:
- 1 GiB of DRAM
- 1 Gigabit ethernet
- 1 USB gadget port
- 1 USB host port with an on-board hub
- 2 QSPI NORs connected to the Cadence QSPI core
- Multiple I2C EEPROMs and one I2C temperature sensor
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
---
V2: Update the defconfig as per Tom's request
P2771-0000 is a P3310 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB micro-B
port, Ethernet, USB3 host port, SATA, PCIe, and two GPIO expansion
headers.
Currently, due to U-Boot's level of support for Tegra186, the only
features supported by U-Boot are the console UART and the on-board eMMC.
Additional features will be added over time.
U-Boot has so far been tested by replacing the kernel image on the device
with a U-Boot binary. It is anticipated that U-Boot will eventually
replace the CCPLEX bootloader binary, as on previous chips. This hasn't
yet been tested.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add minimal dts support for AM335x-ICEv2 board
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Allow am335x-bone.dts to be built and enable uart and timer
for all beaglebones.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].
[1] https://patchwork.ozlabs.org/patch/603583/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The originally committed .dts files for the Pine64 were from an early
proof-of-concept version and should have never been committed upstream.
Replace them with much more mature versions, which also use a different
naming scheme.
Please note that at this point there is at least one binding which has
not been agreed upon, so this is subject to change.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Espresso7420 is a development/evaluation board for Exynos7420 SoC. It
includes multiple onboard compoments (EMMC/Codec) and various
interconnects (USB/HDMI).
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently only the serial pl01x driver is using DT,
and the other drivers still use platform data but
as more DT lands in the upstream kernel the aim is
to migrate the other drivers over to DT as well to
have a fully DT configured hikey u-boot.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.
The dts is identical to the dts submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch adds basic support for the Marvell A375 eval board. Tested
are the following interfaces:
- I2C
- SPI
- SPI NOR
- Ethernet (mvpp2), port 0 & 1
Currently the A375 SerDes and DDR3 init code is not intergrated. So
the SPL U-Boot is not fully functional.
Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:
=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This commit add support for 96Boards Dragonboard410C.
It is board based on APQ8016 Qualcomm SoC, complying with
96boards specification.
Features (present out of the box):
- 4x Cortex A53 (ARMv8)
- 2x USB Host port
- 1x USB Device port
- 4x LEDs
- 1x HDMI connector
- 1x uSD connector
- 3x buttons (Power, Vol+, Vol-/Reset)
- WIFI, Bluetooth with integrated antenna
- 8GiB eMMC
U-Boot boots chained with fastboot in 64-bit mode.
For detailed build instructions see readme.txt in board directory.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
The Pine64+ is a system based on the Allwinner A64 SoC. It is capable of
running AArch64 code and thus is the first of its kind for the sunxi target.
This patch adds a defconfig and device tree chunks for it.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: Change patch description]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
a TRRS headphone jack for stereo out and composite out, a microphone,
an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
and a 40-pin GPIO header.
The added dts file is identical to the one submitted to the upstream
kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
