- A fix for a long standing bug that has been exposed by commit
50128aeb0f ("cyclic: get rid of cyclic_init()") preventing 8xx boards
from booting since u-boot 2023.01
- A GPIO driver for powerpc 8xx chip
- Fixup for powerpc 8xx SPI driver
- A new powerpc 8xx board
- The two devices having that board.
This adds a new board from CS GROUP. The board is called
MCR3000_2G, and has a CPU board called CMPC885.
That CPU board is shared with another equipment that will
be added in a later patch.
That board stores Ethernet MAC addresses in an EEPROM which
is accessed using SPI bus.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
Ports A, C and D are 16 bits ports.
Ports B and E are 32 bits ports.
The "compatible" is used to determine each port type.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
Copied from e83a7e9453 ("powerpc/mpc83xx: Zero boot_flags arg for
calling board_init_f()")
The argument boot_flags of board_init_f() is not used at all in the
powerpc specific board.c init sequence. Now with the generic init
sequence, this boot_flags arg is used by board_init_f().
This patch sets the r3 register that is used to pass the boot_flags
argument from the start.S board_init_f() call to 0 prior to the function
call to avoid unknown content to end up in gd->flags.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Fixes: 09f3ca3dd5 ("arm, powerpc: select SYS_GENERIC_BOARD")
Linux event code must be used in input devices, using buttons.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Property count may change in /buttons node, if more button tests added,
and this will break ofnode_for_each_prop.
Add separate node for mentioned test.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add clk_rcg_set_rate() which allows to configure clocks without programming
MND values. This is required for configuring I2C clocks on QCS404.
Co-developed-by: Mike Worsfold <mworsfold@impinj.com>
Signed-off-by: Mike Worsfold <mworsfold@impinj.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Use standard pinconf drive-strength values from Linux DT bindings rather
than ones based on custom u-boot header. These changes are in direction
to make u-boot DTs for Qcom SoCs to be compatible with standard Linux
DT bindings.
Also, add support for pinconf bias-pull-up.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Currently u-boot maps whole of 1G RAM but there reserved memory ranges on
QCS404 which are reserved for TrustZone, various firmware components etc.
Any access to these reserved memory ranges causes a bus hang issue. So
disable mapping for reserved memory ranges in u-boot.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_ROCKCHIP_OTP defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_FASTBOOT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_USB_KEYBOARD defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_SYS_FSL_ERRATUM_A010539 defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_STM32MP15X_STM32IMAGE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_SAVE_PREV_BL_INITRAMFS_START_ADDR defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_SAVE_PREV_BL_FDT_ADDR defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_ROCKCHIP_EFUSE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_PMIC_STPMIC1 defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_OCTEON_SERIAL_PCIE_CONSOLE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_OCTEON_SERIAL_BOOTCMD defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_MIPS_CM defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 6 usages of this option to the non-SPL form, since there is
no SPL_IMX_MODULE_FUSE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_EXYNOS7420 defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_DISPLAY_CPUINFO defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_CPU_MICROBLAZE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_NET defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_BOOTZ defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_BOOTSTAGE_REPORT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_BOOTSTAGE_FDT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_ARMADA_8K defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_ARMADA_3700 defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_ALLEYCAT_5 defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This has been renamed to CONFIG_ARCH_RMOBILE but this one was left behind.
It doesn't point to a directory that exists, so just drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is set in the Makefile but has no effect in the assembly
code, i.e. the #ifdef branch is never used. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The KONA and KONA_GPIO options don't exist anymore, since this commit:
0f6807e77b arm: Remove bcm28155_ap board
Drop the dead code.
Signed-off-by: Simon Glass <sjg@chromium.org>
convert socrates board to use MPC85XX_HAVE_RESET_VECTOR and
disable CONFIG_OF_BOARD and use common u-boot.dtsi for
creating u-boot-dtb.bin.
Signed-off-by: Heiko Schocher <hs@denx.de>
U-Boot build process for socrates board produces final U-Boot binary in
file u-boot-socrates.bin (by binman) And as a bonus it produces two
unusable broken binaries u-boot-dtb.bin and u-boot.bin (by Makefile).
Clean this up, so final U-Boot binary is in u-boot-dtb.bin
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
As MDIO driver does not support Driver Model, the
pinctrl settings in the MDIO node will not
be applied resulting in PHY not being detected.
To workaround this we add the MDIO pinctrl in
the CPSW3G node in the -u-boot.dtsi file.
Add the missing MDIO and RGMII pinctrl nodes in
k3-am642-r5-evm.dts
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
To test decode_panel_timing add a panel-timings node
and a DM test for decode panel timingd by matching
the panel timing node parameters.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add MV88E61XX DSA support:
- update dt to provide internal MDIO bus and port handles.
U-Boot requires a more restrictive subset of the dt bindings
required by Linux for the sake of simplifying code
- update defconfig to remove old driver and enable new one
- replace mv88e61xx_hw_reset weak override with board_phy_config support
for register configuration that is outside the scope of the DSA driver
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Enable TIMER and TEGRA_TIMER for TEGRA_ARMV7_COMMON and TEGRA210.
Additionally enable SPL_TIMER if build as SPL part and drop
deprecated configs from common header.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom <twarren@nvidia.com>
Enum clock_osc_freq was designed to use only with T20.
This patch remaps it to use additional frequencies, added in
T30+ SoC while maintaining backwards compatibility with T20.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF600T T30
Tested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de> # Surface RT T30
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Thierry Reding <treding@nvidia.com> # T30, T124, T210
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom <twarren@nvidia.com>
Add trivial reset driver extension to the CPG clock driver. The change
turns current CPG UCLASS_CLK driver instance into an UCLASS_NOP proxy
driver, which in turn binds both generic rcar3_clk UCLASS_CLK clock
driver as well as generic rcar_rst UCLASS_RESET reset driver to the
CPG DT node. This way, any other drivers which use the 'reset' DT
property can now obtain valid reset handle backed by a reset driver.
The clock tables have been updated to represent the CPG driver and only
implement the generic CPG proxy driver bind call, which binds the clock
and reset drivers.
The DM_RESET is now enabled for all R-Car Gen3 platforms.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for the R-Car M3-W+ (R8A77961) SoC.
R-Car M3-W+ is very similar to R-Car M3-W (R8A77960), which allows for
both SoCs to share a driver.
Based on Linux commit 2ba738d56db4 ("clk: renesas: r8a7796: Add R8A77961
CPG/MSSR support")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename CONFIG_CLK_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_CLK_R8A77960, to avoid confusion with R-Car M3-W+ (R8A77961),
which will use CONFIG_CLK_R8A77961.
Based on Linux commit 92d1ebae9abf ("clk: renesas: Rename CLK_R8A7796
to CLK_R8A77960")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
R-Car M3-W+ (R8A77961) is pin compatible with R-Car M3-W (R8A77960),
which allows for both SoCs to share a driver.
Based on Linux commit 708c69e9eacc ("pinctrl: sh-pfc: r8a7796: Add
R8A77961 PFC support") and 74ce7a8044b0 ("pinctrl: renesas: r8a7796:
Optimize pinctrl image size for R8A774A1")
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ PFC tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Note that the Kconfig option name has been updated to match the
Linux kernel Kconfig option name, from PINCTRL_PFC_R8A7796 to
PINCTRL_PFC_R8A77960 .
Also note that a new Kconfig option has been added to enable support
for R8A77961 M3-W+ , the Kconfig option name is PINCTRL_PFC_R8A77961 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7795 H3 PFC tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Note that the Kconfig option name has been updated to match the
Linux kernel Kconfig option name, from PINCTRL_PFC_R8A7795 to
PINCTRL_PFC_R8A77951 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car device trees with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
The following script has been used for the synchronization:
$ for i in $(cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) ; do
if [ -e /linux-2.6/arch/arm64/boot/dts/renesas/$i ] ; then
cp /linux-2.6/arch/arm64/boot/dts/renesas/$i arch/arm/dts/ ;
elif [ -e /linux-2.6/arch/arm/boot/dts/$i ] ; then
cp /linux-2.6/arch/arm/boot/dts/$i arch/arm/dts/
else
echo "NOT FOUND: $i"
fi
done
$ git add $( ( cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) | tr " " "\n" | sed 's@^@arch/arm/dts/@g' )
Move the include/dt-bindings/{clk,clock}/versaclock.h header used by
the renesas boards to match Linux 6.1.y as well.
Keep arch/arm/dts/r8a774c0-u-boot.dtsi sdhi3 node as it is now used
by the arch/arm/dts/r8a774c0-cat874.dts board.
Pick s@spi-flash@flash@ change in arch/arm/dts/r8a779a0-falcon-u-boot.dts
from "ARM: dts: Synchronize R-Car V3U DTs with Linux 5.18.3" .
Adjust R8A77990 Ebisu CONFIG_SYS_MMC_ENV_DEV from 2 to 0 to reflect
the card enumeration in ebisu.dtsi /aliases DT node .
Adjust R8A7795 and R8A7796 ULCB CONFIG_SYS_MMC_ENV_DEV from 1 to 0 to
reflect the card enumeration in ulcb.dtsi /aliases DT node .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> # r8a779a0-falcon-u-boot.dts
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> # r8a779a0-falcon-u-boot.dts
Add src and dst address checking, if they
are the same address, just return and don't
copy data anymore.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
When fit image boots from ram, the payload will
be prepared in the address of SPL_LOAD_FIT_ADDRESS.
In spl fit generic flow, it will malloc another
memory address and copy whole fit image to this
malloc address. But it is un-necessary for booting
from RAM.
This patch improves this flow by declare the
board_spl_fit_buffer_addr() to replace the original one.
The larger image size (eq: Kernel Image 10~20MB), it
can save more booting time.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
CCTL operations are available to Supervisor/User-mode
software under the control of the mcache_ctl.CCTL_SUEN
control bit. Enable it to support Supervisor(and User)
CCTL operations.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Priv ISA states:
"In systems without U-mode, the mcounteren register should
not exist."
Check U-Mode is present in MISA before writing to counteren, otherwise
we endup with Illegal Instruction exception on systems without U-Mode.
Also make checking MISA default for M-Mode.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
To improve startup times when booting from QSPI flash, the QSPI frequency
can be configured very early in the boot process [1] to reduce loading
times of U-Boot itself. This patch adds an option to disable setting the
frequency to a default value during SoC initialization.
[1] https://www.nxp.com/docs/en/application-note/AN12279.pdf
Signed-off-by: Mario Kicherer <dev@kicherer.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
NXP tested imx8mn-ddr4 with firmware version 201810 only. Use this
version for all imx8mn targets with DRAM DDR4.
Fixes: 93c4c0e4dd ("arm: dts: imx8mn-u-boot: Create common imx8mn-u-boot.dtsi")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@denx.de>
When routing UART4 using the ECSPI2 pads, register
IOMUXC_UART4_RXD_SELECT_INPUT (offset 0x050C) should be changed only
when dealing with RX, as its name suggests.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
SCFW has fixed a overflow issue in sc_rm_is_pad_owned API. This
requires u-boot to update API implementation, since it will cause
compatible issue. Otherwise all pad checking will have problem and
cause pad setting not continue.
Due to the compatible issue, the new u-boot only works with new
SCFW (API version: 1.21 and later).
old scfw + old u-boot: API overflow issue
old scfw + new u-boot, or new scfw + old u-boot: API compatible issue
new scfw + new u-boot: Working
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Jason Liu <Jason.hui.liu@nxp.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
In some situations the GSC firmware where the EEPROM containing the
model and DRAM configuration may not be ready by the time the SoC
is ready to talk to it over I2C.
Instead of a hard delay, poll the I2C lines to wait until they are
released to avoid the I2C drivers 'Arbitation lost' error message.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add I2C GPIO bus recovery support by adding scl-gpios and sda-gpios for the
various I2C busses on Gateworks Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Synchronizing the device tree with linux introduced a regression.
The U-Boot specific dtsi mustn't override the alias settings for
the eMMC/SD interfaces.
Without this U-Boot cannot access the eMMC and boot the kernel.
Fixes: c21b61bff1 ("colibri-imx6ull/-emmc: synchronise device tree with linux")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Implement basic PSCI provider to let OS turn CPU cores off and on,
power off and restart the system and determine PSCI version. This
is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following Kconfig options:
# CONFIG_PSCI_RESET is not set
CONFIG_ARMV8_MULTIENTRY=y
CONFIG_ARMV8_SET_SMPEN=y
CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y
CONFIG_ARMV8_EA_EL3_FIRST=y
CONFIG_ARMV8_PSCI=y
CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4
CONFIG_ARMV8_SECURE_BASE=0x970000
CONFIG_ARM_SMCCC=y
CONFIG_SYS_HAS_ARMV8_SECURE_BASE=y
Signed-off-by: Marek Vasut <marex@denx.de>
In case U-Boot is the PSCI provider, it is necessary to correctly
program CSU and TZASC registers. Those are poorly documented, so
push in the correct values.
Signed-off-by: Marek Vasut <marex@denx.de>
The common code used to bring up secondary cores requires a final
jump location to be stored in some sort of memory location, define
this memory location to be the start of OCRAM, since it is available.
Signed-off-by: Marek Vasut <marex@denx.de>
In case U-Boot is a PSCI provider, map RAM explicitly as NS,
otherwise secondary cores crash with SError when attempting
to access RAM mapped as secure in EL2.
Signed-off-by: Marek Vasut <marex@denx.de>
The ROM pointers are in fact populated by the ATF BL31 blob, in case
U-Boot itself if the PSCI provider, there is no ATF BL31 blob, hence
ignore the ROM pointers.
Signed-off-by: Marek Vasut <marex@denx.de>
In case U-Boot itself if the PSCI provider on i.MX8M, do not
require the ATF BL31 blob, as at that point the blob is useless
and would interfere with U-Boot operation.
Signed-off-by: Marek Vasut <marex@denx.de>
The custom lowlevel_init implementation is no longer necessary, since
it is responsible for routing and trapping SErrors in U-Boot in EL2,
which is implemented in common code since commit:
6c7691edd5 ("armv8: Always unmask SErrors")
Signed-off-by: Marek Vasut <marex@denx.de>
The RESET2 hook is a PSCI v1.1 functionality, rename the macro accordinly.
Add missing handler for the RESET2 hook, so it can be implemented by U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
In commit d0399a46e7, the device tree was
synchronized from linux and the aliases were dropped.
They need to be kept so that the mmc cards are in the right order.
Without the aliases, u-boot reports:
MMC: FSL_SDHC: 2, FSL_SDHC: 3
With the aliases, u-boot reports:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
The upstream linux device tree does not contain the same aliases than
u-boot (It keeps the devices order with /dev/mmcblk2 and /dev/mmcblk3).
Because this board has been using different aliases in u-boot
and linux, a imx6q-sabrelite-u-boot.dtsi file is added to be
automatically included in imx6q-sabrelite.dts.
This way, linux and u-boot each keep their own aliases and there
is no breakage on current installations.
This should never be done for new boards as we want to keep linux and
u-boot with the same aliases as much as possible.
This patch is only necessary to avoid breaking existing setups.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The property fsl,mux_mask is deleted by commit ed7bda5 (imx8ulp:
synchronise device tree with linux). This causes the pinctrl
driver not work on 8ULP, so fail to print any log.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The changes of commit 6a21c69521 ("arm: dts: imx8mp: add of-list
support to common imx8mp-u-boot.dtsi") breaks the loading of the fip.
This commit fixes the break by modify the configuration properly.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
assign a label for config-SEQ so that the board dts can modify
the configuration more easily.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken
directly from Linux 6.2-rc3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add aliases for the RTCs on the board and on the SoC. This ensures that
the primary RTC is always the one on the board that has a buffered supply
and maximum accuracy.
This is a direct port of the pending commit from linux-next.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
When an I2C clock is enabled inside enable_i2c_clk() the clock rate is
configured as PLL_SYS_MAIN_120M_CLK / 2 = 60MHz.
Currently, the I2C clock is retrieved from I2C1_CLK_ROOT, which
may not be the one that was enabled.
As there is no clock driver for the imx7d, it is better to return 60MHz
for the I2C clock.
This provides a workaround for the imx7d-pico board, where I2C4 is
connected to the PMIC.
With this change, it is possible to convert the imx7d-pico board
to DM_I2C and DM_PMIC.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 56c2dbdaba ("imx: bootaux: cleanup code") introduces the
following LTO related warning:
"
arch/arm/mach-imx/imx_bootaux.c:24:31: warning: type of ‘hostmap’ does not match original declaration [-Wlto-type-mismatch]
24 | const __weak struct rproc_att hostmap[] = { };
| ^
arch/arm/mach-imx/imx8m/soc.c:1590:24: note: array types have different bounds
1590 | const struct rproc_att hostmap[] = {
| ^
arch/arm/mach-imx/imx8m/soc.c:1590:24: note: ‘hostmap’ was previously declared here
../aarch64-linux-gnu/bin/ld: warning: u-boot has a LOAD segment with RWX permissions
"
This is because the weak empty array of structures "hostmap" is eventually
replaced by non-empty array of structures with different number of elements.
Fix this by avoiding weak variable size array, instead use a weak function
which returns single pointer to the array.
Fixes: 56c2dbdaba ("imx: bootaux: cleanup code")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There are no CONFIG_{TOOLS_,SPL_,TPL_,}IMX8M macros, nor is there one for
ARM64. Use plain IS_ENABLED(CONFIG_IMX8M) and IS_ENABLED(CONFIG_ARM64) to
avoid expanding the {TOOLS_,SPL_,TPL_,} part.
Fixes: 56c2dbdaba ("imx: bootaux: cleanup code")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Originally, the mmc aliases node was present in imx6qdl-sabresd.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a regression in which the SD card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the SD card (esdhc3) was
mapped to mmc1.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Reported-by: Carlos Rafael Giani <dv@pseudoterminal.org>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.
This reinstates change from commit:
e26d0152d6 ("ARM: imx: Decode ECSPI env location from i.MX8M ROMAPI tables")
which has been dropped in commit:
b0a284a7c9 ("imx: move get_boot_device to common file")
Fixes: b0a284a7c9 ("imx: move get_boot_device to common file")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This reverts commit f5315dd629.
[why]
TPL is not mandatory for not all Rockchip SoCs, some SoCs like
RK356x, and RK3588 still use mainline u-boot without TPL as
their ddr init programs are accessed via binaries provided by
Rockchip instead of ddr source code.
Marking TPL build makes it not able to build u-boot.itb on
RK356x targets so revert this so that it can build an SPL build
that would support all across Rockchip platforms.
Suggested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Tested-by: Anand Moon <linux.amoon@gmail.com> # CM3
Add pinctrl's for high speed eMMC and MMC cards.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
In case the CONFIG_IMX8M_LPDDR4 and CONFIG_IMX8M_DDR4 options are both
disabled (i. e. BSH boards), binmain fails because DDR4 bin files are
missing.
Fixes: 93c4c0e4dd ("arm: dts: imx8mn-u-boot: Create common imx8mn-u-boot.dtsi")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added
It doesn't use the odroid-n2 board support since ADC revision
collides with Odroid-N2+ and since it doesn't have on-board ethernet
no need to load the MAC address from eFuses.
Link: https://lore.kernel.org/r/20230126-u-boot-odroid-n2l-v1-2-c60f695e0f6c@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This driver supports the PCIe controller on the Apple M1 and
M2 SoCs. The code is adapted from the Linux driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Test that we correctly probe an IOMMU that is mapped by an
"iommu-map" device tree property of a PCIe controller node.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SK architecture comprises of baseboard and a SOM board. The
AM68 Starter Kit's baseboard contains most of the actual connectors,
power supply etc. The System on Module (SoM) is plugged on to the base
board. Therefore, add support for peripherals brought out in the base
board.
Schematics: https://www.ti.com/lit/zip/SPRR463
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
AM68 Starter Kit (SK) is a low cost, small form factor board designed
for TI’s AM68 SoC. TI’s AM68 SoC comprises of dual core A72, high
performance vision accelerators, hardware accelerators, latest C71x
DSP, high bandwidth real-time IPs for capture and display. The SoC is
power optimized to provide best in class performance for industrial
applications.
AM68 SK supports the following interfaces:
* 16 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.1 Type-C port
* x2 USB 3.1 Type-A ports
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi GPIO header
SK's System on Module (SoM) contains the SoC, PMIC, DDR and OSPI flash.
Therefore, add support for the components present on the SoM.
Schematics: https://www.ti.com/lit/zip/SPRR463
TRM: http://www.ti.com/lit/pdf/spruj28
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Although the board_init_f API initialises the SoC, the API name is
incorrectly specified and misleads the functionality. This file should
only include k3-specific functionality. Change the API's name to something
more K3-specific and separate the function to make it more modular.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY9PmzwAKCRDKSWXLKUoM
IYWxAJwNgiXtFT17pBy+1M0JvSWgyvWF3QCfTQG2Krnw0+d65PF5A7UFTDL7SZM=
=cMrc
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx chnages for v2023.04-rc1
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
Drop boot_linux variable as it is not assigned anywhere. Now that there is
no variable controlling linux boot in spl_start_uboot(), make this
function always return false when falcon mode is enabled.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20230125164157.1638680-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Make spl_start_uboot() available only if CONFIG_SPL_OS_BOOT is enabled,
since it is only used for falcon mode.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20230125164157.1638680-1-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The FIT generated after the switch to using binman is using different
values for firmware and loadables properties compared to the old script.
With the old script:
firmware = "atf-1";
loadables = "u-boot", "atf-2", ...;
After switch to binman:
firmware = "u-boot";
loadables = "atf-1", "atf-2", ...;
This change result in SPL jumping directly into U-Boot proper instead of
initializing TF-A.
With this patch the properties change back to:
firmware = "atf-1";
loatables = "u-boot", "atf-2", ...;
Fixes: e0c0efff2a ("rockchip: Support building the all output files in binman")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add sha256 hash to FIT images when CONFIG_SPL_FIT_SIGNATURE=y.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL load FIT images by reading the data aligned to block length.
Block length aligned image data is read directly to the load address.
Unaligned image data is written to an offset of the load address and
then the data is memcpy to the load address.
This adds a small overhead of having to memcpy unaligned data, something
that normally is not an issue.
However, TF-A may have a segment that should be loaded into SRAM, e.g.
vendor TF-A for RK3568 has a 8KiB segment that should be loaded into the
8KiB PMU SRAM. Having the image data for such segment unaligned result
in segment being written to and memcpy from beyond the SRAM boundary, in
the end this results in invalid data in SRAM.
Aligning the FIT and its external data to MMC block length to work
around such issue.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
This contains some fixes, and the first bunch of some clean up patches
to get rid of legacy GPIO and PMIC code.
Highlight is the DM AXP PMIC driver, which is required to convert some
drivers over to use DM regulators, and also is required to get rid
of some less optimal PMIC setup code in Trusted Firmware. This isn't
enabled by any defconfig yet, but can be enabled manually and works. For
the full glory some patches are still missing, and this requires more
testing, which would be simpler if the core code is upstream.
SOM itself from PS point of view is using the same configuration as K26
that's why reuse that files and only change compatible strings.
The reason for creating own set of files is just in case when versions
start to diverge because of HW change, supply chain issue, etc.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/61f877ec0b480c5bd368a1211fc73ff7465016bd.1674043915.git.michal.simek@amd.com
Most tests don't want these and they can create a lot of noise. Add a way
to disable them. Use that in tests, with a flag provided to enable them
for tests that need this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
The test code for virtio is fairly simplistic and does not actually create
a block device. Add a way to specify the device type in the device tree.
Add a block device so that we can do more testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
For bootstd tests it is seldom useful to have ethernet enabled. Add a way
to disable it, so that ethernet operations like tftpboot do nothing.
Signed-off-by: Simon Glass <sjg@chromium.org>
To determine whether we have been booted from an eMMC boot partition, we
replay some of the checks that the BROM must have done to successfully
load the SPL. This involves a checksum check, which currently relies on
the SPL being wrapped in an "eGON" header.
If a board has secure boot enabled, the BROM will only accept the "TOC0"
format, which is internally very different, but uses the same
checksumming algorithm. Actually the only difference for calculating the
checksum is that the size of the SPL is stored at a different offset.
Do a header check to determine whether we deal with an eGON or TOC0
format, then set the SPL size accordingly. The rest of the code is
unchanged.
This fixes booting from an eMMC boot partition on devices with secure
boot enabled, like the Remix Mini PC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
For legacy reasons we were defining the card detect GPIO for all sunxi
boards in each board's defconfig.
There is actually no need for a card-detect check in the SPL code (which
consequently has been removed already), and also in U-Boot proper we
have DM code to query the CD GPIO name from the device tree.
That means we don't have any user of that information left, so can
remove the definitions from the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
For some reasons shrouded in mystery, the code saving the FEL state was
saving the SCTLR register twice, with the second copy trying to justify
itself by using its ancient "control register" alias name.
Drop the redundant second copy, both from the fel_stash data structure,
and also the code saving and restoring it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Both the values and the MMIO addresses that we need during the 64-bit FEL
restore are smaller than 2^32, so we don't need to do any 64-bit loads.
Change the loads to only load 32 bits worth of data, that saves us some
bytes for storing the values.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
When support for the Allwinner F1C100s SoC was originally introduced,
its DT lacked any MMC nodes, which upset our sunxi-u-boot.dtsi overlay,
when it tried to add an alias to the SD card. To quickly fix this back
then, we guarded that alias with a preprocessor macro.
Now the F1C100s family has gained MMC nodes, so we don't need the
special treatment anymore. Just remove this guard.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As this is used on both ARM and PowerPC platforms, this needs to be
listed in arch/Kconfig.nxp and match how they're currently used by
select'ing them under the required PowerPC ARCH_xxx options.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this is used on both ARM and PowerPC platforms, this needs to be
asked in arch/Kconfig.nxp. Set the PowerPC defaults based on
arch/powerpc/include/asm/config_mpc85xx.h and remove the default set in
drivers/mtd/nand/raw/fsl_ifc_nand.c
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point, the Linux code for "lib1funcs" has changed rather
dramatically. While a resync would be beneficial, it's outside the scope
of what we need here. Simply remove the define for CONFIG_AEABI and
tests for it.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to avoid defining CONFIG_ARMV[78_]SECURE_BASE as empty in the
linker scripts, if not already defined, add and use
__ARMV[78_]SECURE_BASE for when the base is not defined and we want the
linker scripts to continue.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove some CONFIG symbols and related comments, etc, that are unused
within the code itself at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- 5inch 854×480 MIPI-DSI TFT LCD
Link: https://lore.kernel.org/r/20230119-u-boot-odroid-go-ultra-v1-2-f96bab9db396@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
With CONFIG_DM_USB_GADGET=y, we no longer need any board_usb_*() logic
because:
* the dwc2 driver is DM compatible, and handles its own clock enabling
* the dwc3-meson-gxl glue drivers handles "force mode switching"
Remove all mach-meson gx & axg usb code and enable CONFIG_DM_USB_GADGET.
Note: Only configs having both CONFIG_USB_DWC3_MESON_GXL=y *and*
USB_GADGET_DWC2_OTG=y have been updated.
Thanks for the original work from Mattijs at [1]
[1] https://lore.kernel.org/all/20221024-meson-dm-usb-v1-2-2ab077a503b9@baylibre.com/
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20230117-u-boot-usb-gxl-otg-dm-v1-2-2853f6d75b06@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmPIpV4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZuqwgA0UpYQEX6/MegzHSCIx3AMT4rCF1Ytitr
LS4Cbvj1Q09Rt9jriW7wAV5AobVPwGf2L5SVcnWv2I9+MmypDIXEe8HIrt2fRFu9
bzn/2GOzXczuXqPFa/CWOUwjvCzTb8Sl9NtRszrP5NvOzuN15x00ZUYaXFO7fgsB
zZMzOKxemwjdtLaox+x+VIJ95HMDEkYrWTAqTPg74CNVSjRbbLNqNq0zqkHB8SnH
ubgphtIKYItTeIXcfIa9V4LeQp0ZitkzSfAibX+nIPCMPg9jbG9MrQQ+VvSZDjnM
y8wa8gFj47Ek+gGNFXMHIpO6tBd83uHRgtf2x+zhcovLELYnZ6fDGw==
=1K6m
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18jan23' of https://source.denx.de/u-boot/custodians/u-boot-dm
convert rockchip to use binman
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
Add the required binman images to replace the Makefile rules which are
currently used. This includes subsuming:
- tpl/u-boot-tpl-rockchip.bin if TPL is enabled
- idbloader.img if either or both of SPL and TPL are enabled
- u-boot.itb if SPL_FIT is enabled
- u-boot-rockchip.bin if SPL is used, either using u-boot.itb when
SPL_FIT is enabled or u-boot.img when it isn't
Note that the intermediate files are dropped with binman, since it
producing everything in one pass. This means that
tpl/u-boot-tpl-rockchip.bin is not created, for example.
Note that for some 32-bit rk3288 boards, rockchip-optee.dtsi is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable multiple-images so we can generate more than one image. Also
add a comment for the end of the #if block.
Signed-off-by: Simon Glass <sjg@chromium.org>
This board is useful for benchmarking overall U-Boot performance. Enable
the bootstage feature so we get a report.
Since this returns to the boot rom before finishing executing
board_init_r() in SPL, add a few bootstage calls so that we can collect
timing from TPL.
For the stash region, use a portion of SRAM, 64KB below the stack top.
This allows the TPL image to be up to nearly 120KB (it is typically about
64KB). SPL normally runs from SDRAM at 0, so can use the same stash
region.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the notrace attribute so that timer functions can be used when
tracing. This is required to avoid infinite loops when recording a trace.
Signed-off-by: Simon Glass <sjg@chromium.org>
The event framework is just that, a framework. Enabling it by itself
does nothing, so we shouldn't ask the user about it. Reword (and correct
typos) around this the option and help text. This also applies to
DM_EVENT and EVENT_DYNAMIC. Only EVENT_DEBUG and CMD_EVENT should be
visible to the user to select, when EVENT is selected.
With this, it's time to address the larger problems. When functionality
uses events, typically via EVENT_SPY, the appropriate framework then
must be select'd and NOT imply'd. As the functionality will cease to
work (and so, platforms will fail to boot) this is non-optional and
where select is appropriate. Audit the current users of EVENT_SPY to
have a more fine-grained approach to select'ing the framework where
used. Also ensure the current users of event_register and also select
EVENT_DYNAMIC.
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reported-by: Oliver Graute <Oliver.Graute@kococonnector.com>
Reported-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Fixes: 42fdcebf85 ("event: Convert misc_init_f() to use events")
Fixes: c5ef202557 ("dm: fix DM_EVENT dependencies")
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The function arch_cpu_init_dm was renamed to fsp_setup_pinctrl in these
cases, so rename debug / docs to match.
Cc: Simon Glass <sjg@chromium.org>
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To quote the author:
So far standard boot lacks a boot menu, although it is possible to create
a rudimentary one using the existing 'bootmenu' command.
Even then, this text-based menu offer only basic functionality and does
not take full advantage of the displays which are common on many devices.
This series provides a 'bootflow menu' command which allows the user to
select from the available bootflows. An attempt is made to show the name
of the available operating systems, by reading more information into the
bootflow. A logo can be read also, where supported, so that this can be
presented to the user when an option is highlighted.
Full use is made of TrueType fonts, if enabled. For cases where only a
serial console is available, it falls back to a simple text-based menu.
All of this is implementing using a new 'expo' construct, a collection of
scenes (like menu screens) which can be navigated by the user to view
information and select options. This is fairly general and should be able
to cope with a wider array of use cases, with less hacking of the menu
code, such as is currently needed for CMD_BOOTEFI_BOOTMGR.
Of course it would be possible to enhance the existing menu rather than
creating a new setup. Instead it seems better to make the existing menu
use expo, if code space permits. It avoids the event-loop problem and
should be more extensible, given its loosely coupled components and use of
IDs instead of pointers. Further motivation is provided in the
documentation.
For now the CLI keypress-decoding code is split out to be used by the new
menu. The key codes defined by menu.h are reused also.
This is of course just a starting point. Some ideas for future work are
included in the documentation.
With CONFIG_DM_USB_GADGET=y, we no longer need any board_usb_*() logic
because:
* the dwc2 driver is DM compatible, and handles its own clock enabling
* the dwc3-meson-g12a glue drivers handles "force mode switching"
Remove all mach-meson/g12a usb code and enable CONFIG_DM_USB_GADGET.
Note: Only configs having both CONFIG_USB_DWC3_MESON_G12A=y *and*
USB_GADGET_DWC2_OTG=y have been updated.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20221024-meson-dm-usb-v1-2-2ab077a503b9@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
For Kirkwood boards, it is necessary to have early malloc in DRAM area
when Driver Model for Serial is enabled. Please see Michael's patch here:
https://lore.kernel.org/u-boot/20220817193809.1059688-20-michael@walle.cc/
This patch enables the early malloc in DRAM for all Kirkwood boards.
Note that this will work for boards that have either non-DM serial
and DM_SERIAL. Also, add the CONFIG_KIRKWOOD_COMMON option to enable
DM_SERIAL as a common option for boards that have been tested.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Add a test which checks that two operating systems can be displayed in a
menu, allowing one to be selected.
Enable a few things on snow so that the unit tests build.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should use the cmd/ directory for commands rather than for common code
used elsewhere in U-Boot. Move the common 'source' code into
image-board.c to achieve this.
The image_source_script() function needs to call run_command_list() so
seems to belong better in the command library. Move and rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for starting timer by setting up time stamp generator
registers. This is done only for EL3 i.e. mini U-Boot case.
For other cases, it will be done TF-A.
Add COUNTER_FREQUENCY and IOU_SWITCH_DIVISOR0 to Kconfig so that they
can be tuned as required.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/fcd8b0dc4b45a11f5e753afff42f84738ac813da.1673336645.git.michal.simek@amd.com
Sync the px30 dtsi from Linux kernel v6.1.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
It is possible to boot U-Boot proper from a different storage medium
than the one used by the BOOTROM to load the SPL. This information is
stored in the u-boot,spl-boot-device Device Tree property and is
accessible from U-Boot proper so that it has knowledge at runtime where
it was loaded from.
Let's add support for this feature for px30.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
BOOTROM sets a bit in a CPU register so that the software can know from
where the first stage bootloader was booted. One use case for this is to
specify the default loading medium for U-Boot proper to match the one
used by the BOOTROM to load the SPL (same-as-spl in
u-boot,spl-boot-order).
Let's create the mapping between BOOTROM value and Device Tree node
names for MMC devices.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
The grf and cru are only used when no UART base is provided by the user
(defaults to UART2) or for UART1, UART3 and UART5 to be used for the
debug UART. Therefore, let's surround those variable definitions with
the proper checks.
This wasn't an issue before support for UART0 was added, because all
cases were using cru and grf. UART0 only uses pmucru so there's a need
to not define those variables anymore.
Fixes: d0af506625 ("rockchip: px30: support debug uart on UART0")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pinephone Pro is another device by PINE64. It's closely related
to the Pinebook Pro of which this initial support is derived from.
Specification:
- A variant of the Rockchip RK3399
- A 6 inch 720*1440 DSI display
- Front and rear cameras
- Type-C interface with alt mode display (DP 1.2) and PD charging
- 4GB LPDDR4 RAM
- 128GB eMMC
- mSD card slot
- An AP6255 module for 802.11ac WiFi and Bluetooth 5
- Quectel EG25-G 4G/LTE modem
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Initial support for the PinePhone Pro has now landed upstream in
Linux 6.1 RC1 so sync the dts from 6.2-rc1 for initial support.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
IO board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add u-boot,dm-spl and u-boot,dm-pre-reloc related properties
for Rockchip RV1126 SoC.
Both eMMC and SD boot are tested in Edgeble Neu2 SoM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
evaluation board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Neural Compute Module 2(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RV1126 from Edgeble AI.
General features:
- Rockchip RV1126
- 2/4GB LPDDR4
- 8/16/32GB eMMC
- 2x MIPI CSI2 FPC connector
- Fn-link 8223A-SR WiFi/BT
Industrial grade (-40 °C to +85 °C) version of the same class of module
called Neu2k powered with Rockchip RV1126K.
Neu2 needs to mount on top of Edgeble IO boards for creating complete
platform solutions.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Unsecure the dram area so that MMC, USB, and SFC controllers
can able to read data from dram.
Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip RV1126 is a high-performance vision processor SoC
for IPC/CVR, especially for AI related application.
Add arch core support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change-Id: I22fde40ec375e3c6aba39808abf252edc45d4b04
RV1126 is a high-performance vision processor SoC for IPC/CVR,
especially for AI related application.
It is based on quad-core ARM Cortex-A7 32-bit core which integrates
NEON and FPU. There is a 32KB I-cache and 32KB D-cache for each core
and 512KB unified L2 cache. It has build-in NPU supports INT8/INT16
hybrid operation and computing power is up to 2.0TOPs.
This patch add basic core dtsi support.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add full ddr pctl registers and bit masks for px30.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DDR chip capacity is computed based on GRF split in some
Rockchip SoC's like PX30 and RV1126.
Add split argument in ddr print info so-that the respective
ddr driver will pass the grf split.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This synchronizes the Device Trees related to Puma RK3399 SoM with Linux
kernel next-20221114 to include two important changes pertaining to
eMMC and SD card instability.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
By default, the PX30 is configured for watchdog and tsadc to trigger a
second global reset which is a more permissive reset than first global
reset.
From TRM part 1 "2.3 System Reset Solution":
glb_srstn_1 will reset the all logic, and
glb_srstn_2 will reset the all logic except GRF, SGRF and all GPIOs.
This enforces that the watchdog and tsadc trigger glb_srstn_1 as
similarly done for RK3399 in U-Boot (in SDRAM driver for some reason?),
TF-A and Coreboot.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND
array and the VCCQ supplies the bus. On Condor, the VCC is connected to
3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust the pinmux
to match the bus, which is always operating in 1.8V mode.
Based on Linux commit 69efe4bbeda50745 ("arm64: dts: renesas: condor:
Switch eMMC bus to 1V8") from Wolfram Sang
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
This board requires SPI NOR fast-read, otherwise the SPI NOR
access returns corrupted data. Enable the fast-read explicitly
in DT as it has been disabled in the MTD subsystem by commit
d008190920 ("mtd: spi-nor: Mask out fast read if not requested in DT")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
-----BEGIN PGP SIGNATURE-----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=SNID
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230113' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add driver to manage onboard hub supplies
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
With U-Boot having access to ROM API call table, it is possible to use
the ROM API call it authenticate e.g. signed kernel fitImages using the
BootROM ECDSA support. Make this available by pulling the ECDSA BootROM
call support from SPL-only guard.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The ROM API table pointer is no longer accessible from U-Boot, fix
this by passing the ROM API pointer through. This makes it possible
for U-Boot to call ROM API functions to authenticate payload like
signed fitImages.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The STM32MP15xx platform currently comes with two incompatible
implementations of save_boot_params() weak function override.
Factor the save_boot_params() implementation into common cpu.c
code and provide accessors to read out both ROM API table address
and DT address from any place in the code instead.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
In case Dcache is enabled while the ECDSA authentication function is
called via BootROM ROM API, the MMU tables are set up and the BootROM
region is not marked as executable, so an attempt to run code from it
results in a hang. Mark the BootROM region as executable as suggested
by Patrick to prevent the hang.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
_relocate() needs the information in .rela* for self relocation
of the EFI binary.
Fixes: d7ddeb66a6 ("efi_loader: fix building aarch64 EFI binaries")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The fs_loader device is used to pull in settings via the chosen node.
However, there was no library function for this, so arria10 was doing it
explicitly. This function subsumes that, and uses ofnode_get_chosen_node
instead of navigating the device tree directly. Because fs_loader pulls
its config from the environment by default, it's fine to create a device
with nothing backing it at all. Doing this allows enabling
CONFIG_FS_LOADER without needing to modify the device tree.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for "st,stm32mp13-bsec" for STM32MP13x in the
bsec driver based on OP-TEE pseudo TA STM32MP BSEC.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When OP-TEE is used, the SMC for BSEC management are not available and
the STM32MP BSEC pseudo TA must be used (it is mandatory for STM32MP13
and it is a new feature for STM32MP15x).
The BSEC driver try to open a session to this PTA BSEC at probe
and use it for OTP read or write access to fuse or to shadow.
This patch also adapts the commands stm32key and stboard to handle
the BSEC_LOCK_PERM lock value instead of 1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove unnecessary return in stm32mp_bsec_write_lock and replace tab
by space for plat_auto opts.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The timer units in the stm32mp15x CPUs have interrupts, depending on the
timer flavour either one "global" or four dedicated ones. Add the irqs
to the timer units on stm32mp15x.
Sync the DT Files with linux kernel v6.1 and with commit a9b70102253ce
("ARM: dts: stm32: Add timer interrupts on stm32mp15")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove unnecessary space in device tree stm32mp15xx-dkx.dtsi.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The include file stm32mp1-clksrc.h is not necessary for the SCMI STM32MP15
dtsi files as the clock tree is not defined in the U-Boot SCMI device tree;
these SCMI device tree only support TFABOOT with stm32mp15_defconfig,
SPL with the basic boot defconfig is not supported.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for USB2514B onboard hub on stm32mp157c EV1 board. The HUB
is supplied by a 3v3 PMIC regulator.
[backport from linux ad9591b01d24]
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
phy-stm32-usbphyc bindings uses a connector node with vbus-supply
property.
[backport from linux 43e55d778a6b]
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Having NXP specific items in the main menu is confusing. Especially
the comment line
*** Other functionality shared between NXP SoCs ***
is simply misleading.
Move all NXP stuff into a separate sub-menu.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Put all entries for skipping low-level initialization into a sub-menu.
Use different titles for main U-Boot, SPL, TPL.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Before this was named just evm, which doesn't match the naming
of the other TI board file directory and makes it look like a
common directory for evms. Name this omap3evm.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Derald Woods <woods.technical@gmail.com>
KASLR address is needed to boot fully functional Android.
KASLR is set by primary bootloader, and since u-boot is used
as a secondary bootloader(replacing kernel) on sdm845 platform,
KASLR may be found by comparing memory chunks at relocaddr over
supposed KASLR range.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Texas Instruments has begun enabling security settings on the SoCs it
produces to instruct ROM and TIFS to begin protecting the Security
Management Subsystem (SMS) from other binaries we load into the chip by
default.
One way ROM and TIFS do this is by enabling firewalls to protect the
OCSRAM and HSM RAM regions they're using during bootup.
The HSM RAM the wakeup SPL is in is firewalled by TIFS to protect
itself from the main domain applications. This means the 'bootindex'
value in HSM RAM, left by ROM to indicate if we're using the primary
or secondary boot-method, must be moved to OCSRAM (that TIFS has open
for us) before we make the jump to the main domain so the main domain's
bootloaders can keep access to this information.
Signed-off-by: Bryan Brattlof <bb@ti.com>
The boot mode detection assumes that BOOT_DEVICE_MMC2 should always
result in MMCSD_MODE_FS, but MMCSD_MODE_RAW is also a valid option for
this port.
The current logic also avoids looking at the bootmode pin strapping,
which should be the primary means of determining whether a device is
being booted in MMCSD_MODE_EMMCBOOT mode.
Switch around the logic to check the boot mode to determine whether the
eMMC boot mode is expected or MMC/SD boot mode. From there we can look
at the boot mode config if in MMC/SD boot mode to determine whether to
attempt RAW or FS based booting.
This change allows U-Boot to also be successfully booted from RAW
offsets in addition to from a filesystem.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
It is incorrect to keep commands in the arch/ folder.
Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230110105650.54580-3-avromanov@sberdevices.ru
[narmstrong: moved after cmd/sound in index.rst]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This function can be used by other modules. Also add comments.
Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20230110105650.54580-2-avromanov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
TI phy requires a reset before PHY address detection to make sure
correct strapping via MIO is detected. Facilitate the same using
ethernet-phy-id compatible string. GPIO reset entry will be added in
a separate commit.
This support is present in RevA but needs to be extended to RevB/1.0/1.1
versions which are built on top.
Fixes: 13622c7a9d ("arm64: zynqmp: Describe TI phy as ethernet-phy-id")
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6d500a83a787316353d4b26c75d1b51d29e3730e.1670854455.git.michal.simek@amd.com
The Cadence GEM/MACB driver now utilizes the platform-level reset on the
ZynqMP platform. Add reset definitions to the ZynqMP platform device
tree to allow this to be used.
Linux upstream commit (e461bd6f43f4e568f7436a8b6bc21c4ce6914c36).
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/14e3637735dbc626659e96d142f04a63398362f8.1670590595.git.michal.simek@amd.com
When building with binutils 2.39 warnings
*_efi.so has a LOAD segment with RWX permissions
occur.
Use SHF_WRITE | SHF_ALLOC as section flags for the .data section.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmO2mnEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBAOB/4y7e9y0jdKSWDwMdZj
enXK/U/GREFyuiSdadil0aJl9WfayjwZkh7uHSTj4pi9ApNivfoqsL7WZYpJxhRD
WlpNhs3TZ70i8CgKUosdzcpquAQZUZhg6iV5DCObrK6yNJRGOXLIwMOd+vw/Xz6/
YTGqzivEDMBuH/9HLuC0m+26PEpff8nenNEjC2k8ssG26ojLz7oCQh2HoHcSgNRc
HkEYlFJ/Le8kM8Ak2F3ebmsfgMTnFrRVwV1BsZa5vO0BrMYgJCORsl7Cnfcw6/2N
LEHG7kwlSorJeETn/gkLiZ+NyqzU+oFH0jGRZ5Ciqg1qcCO3k9yBMgWQzd7nTL6C
5oZA
=Ocdd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.04 cycle:
This feature set includes the new DM-based NAND flash driver (old non-DM
driver is still kept for backwards compatibility), and the move to DM
NAND flash driver for sam9x60ek board. Feature set also includes
devicetree alignment for sama7g5 with Linux, devicetree alignment on USB
with Linux for all boards (sama5, sam9x60), chip id for sama7g5, minor
configs and tweaks.
commit 777aaaa706 ("common/memsize.c: Fix get_effective_memsize() to check
for overflow") because the effective DDR effective size is reduce by 4KiB
and sometime the board hang on boot
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmO3+ZUACgkQ4rK92eCq
k3VHfQf9Fd9zjv8ljJoTW4IHjh0hW4M7KJJ44OplpxgLBKy9lO1LCGxF3V5EAdGM
yBQsRfAjBKiTx8bM7d30dZ2SbQOMjVgbI+VDYI1Pyzzo6wkmrc5uKj16/1Zt9FbR
M26ftJ07uT4hOinD2WXhD4LKH9oMM4p7d03P1q4PPbFPR5+37UEU01fLlCH+SW0R
ajUVPdG+2Pn8g6+rjfVo27dZPi02PBVe8ODvEt63hwMkXqcfHFGMlP4d9vIrArcH
Q9vt1YeyaK+lQdpvctTaH2iw13JtJKpJZxsw63sMOU3+PWFneIKD0gSUKGWrKRnI
kfIKfSU4mJB2+Xeq+2M7O5nLYXT9kA==
=OFHo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230106' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp: Fix board_get_usable_ram_top(): workaround to avoid issue after the
commit 777aaaa706 ("common/memsize.c: Fix get_effective_memsize() to check
for overflow") because the effective DDR effective size is reduce by 4KiB
and sometime the board hang on boot
The QSPI is accessed via the RPC-IF, but the compatible flags
previously used a different name. This compatibel name was changed
which broke the ability to access the QSPI. Fix this by removing
the custom naming reference.
Fixes: 68083b897b ("renesas: Fix RPC-IF compatible values")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Since commit 2f96d4dd95 ("imx7s/d: synchronise device trees with linux")
the imx7d-pico board no longer boots.
The reason is that prior to the above commit there was an explicit
inclusion of arch/arm/dts/imx7d-pico-u-boot.dtsi inside imx7d-pico.dtsi.
After the syncing with the Linux upstream dtsi, this u-boot.dtsi inclusion
is gone and the board fails to boot.
U-Boot uses the imx7d-pico-pi.dtb file, so rename the u-boot.dtsi to
imx7d-pico-pi-u-boot.dtsi which gets included automatically by U-Boot
standard make logic and makes the board boot again.
Signed-off-by: Fabio Estevam <festevam@denx.de>
U-Boot build system builds final U-Boot binary for socrates board in custom
file u-boot-socrates.bin (instead of standard u-boot.bin). Output target
file u-boot-socrates.bin is generated by binman as defined in board binman
config file arch/powerpc/dts/socrates-u-boot.dtsi.
But binman was disabled in commit 5af42eafd7 ("Makefile: Reduce usage of
custom mpc85xx u-boot.bin target") for all mpc85xx boards which do not use
standard powerpc binman config file arch/powerpc/dts/u-boot.dtsi and boards
which do not require binman at all.
The only such mpc85xx board is socrates. So since that commit, U-Boot does
not final binary for socrates board anymore.
Fix this issue by re-enabling binman for socrates board. And build process
starts again producing u-boot-socrates.bin binary.
Note that build process for this socrates board always produce u-boot.bin
binary which is broken and not usable for socrates board. Long term
solution should be to disable building broken binary u-boot.bin and then
renaming u-boot-socrates.bin to u-boot.bin, or switching to use common
powerpc binman config file arch/powerpc/dts/socrates-u-boot.dtsi (if it is
possible).
Fixes: 5af42eafd7 ("Makefile: Reduce usage of custom mpc85xx u-boot.bin target")
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Heiko Schocher <hs@denx.de>
Do not access gd->ram_size and assume this is actual valid RAM size. Since commit
777aaaa706 ("common/memsize.c: Fix get_effective_memsize() to check for overflow")
the RAM size may be less than gd->ram_size , call get_effective_memsize() to get
the limited value instead.
The aforementioned commit makes STM32MP15xx boards with 1 GiB of DRAM
at 0xc0000000 hang on boot, which is a grave defect.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add the required pinctrl, gpio and phy properties required by the
USB DT nodes of the sama7g5ek boards. Since these have not yet been
defined in upstream Linux, place them in the U-Boot specific DT file.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Define the USB and UTMI DT nodes for the sama7g5 SoC's. Since these have
not yet been defined in upstream Linux, place them in the U-Boot specific
DT file.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add the required pinctrl and gpio properties required by the USB DT
nodes of the sam9x60ek boards.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Add the required pinctrl and gpio properties needed by the USB DT nodes
of the sam9x60_curiosity boards.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
While our EFI binaries execute without problems on EDK II they crash on
a Lenovo X13s. Let our binaries look more like what EDK II produces:
* move all writable data to a .data section
* align sections to 4 KiB boundaries (matching EFI page size)
* remove IMAGE_SCN_LNK_NRELOC_OVFL from .reloc section flags
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Remove init of UART-clock and UART-reset in arch_cpu_init(). Add DEBUG_UART
to s5p4418_nanopi2_defconfig.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
All uniphier v7 SoCs have cortex-a9 and use cortex-a9 global timer
in a simple implementation. Now DM_TIMER of it is available
on 35751c7f3f ("timer: sti: convert sti-timer to arm a9 global timer"),
so let's switch to it.
The old driver reads the lower 32bits of counter field
and sets the prescaler as 50 with PERIPHCLK(=50MHz),
so the global timer works as a 32-bit 1MHz timer.
The DM_TIMER uses the whole 64bits with no prescaler,
so the global timer works as a 64-bit PERIPHCLK timer.
CONFIG_SYS_HZ_CLOCK is set as the default PERIPHCLK frequency,
if there is no 'clocks' property in devicetree.
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
The 'base' GPIO controller property is unused in u-boot and Linux. It is
also not documented in the binding. So drop it.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
'active_clk_edges' and 'chipselect_num' SPI controller properties are
unused in u-boot and Linux. They are also not documented in the binding.
So drop them.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
kmcent2-u-boot.dtsi file contains copy of powerpc u-boot.dtsi binman file.
So remove code duplication and replace it by including u-boot.dtsi file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The correct value for 'entry-method' in the idle-states binding is 'psci',
not 'arm,psci'. It hasn't mattered because it isn't used by the OS.
Signed-off-by: Rob Herring <robh@kernel.org>
The "arm,armv7-timer-mem" schema defines the address sizes for child
nodes to be 32-bit as there's no need for 64-bit offsets and sizes of
the child 'frame' nodes.
Signed-off-by: Rob Herring <robh@kernel.org>
DT node names should follow generic names defined in the DT spec. These
are also now checked by dtschema tools.
Signed-off-by: Rob Herring <robh@kernel.org>
Add the definition of the pinctrl for the MCU domain.
Same as kernel commit 500e6dfbb465531150ac6e2ff0856dd357ddc8a4
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
As discussed previously [1,2], the source command is not safe to use with
verified boot unless there is a key with required = "images" (which has its
own problems). This is because if such a key is absent, signatures are
verified but not required. It is assumed that configuration nodes will
provide the signature. Because the source command does not use
configurations to determine the image to source, effectively no
verification takes place.
To address this, allow specifying configuration nodes. We use the same
syntax as the bootm command (helpfully provided for us by fit_parse_conf).
By default, we first try the default config and then the default image. To
force using a config, # must be present in the command (e.g. `source
$loadaddr#my-conf`). For convenience, the config may be omitted, just like
the address may be (e.g. `source \#`). This also works for images
(`source :` behaves exactly like `source` currently does).
[1] https://lore.kernel.org/u-boot/7d711133-d513-5bcb-52f2-a9dbaa9eeded@prevas.dk/
[2] https://lore.kernel.org/u-boot/042dcb34-f85f-351e-1b0e-513f89005fdd@gmail.com/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Two callers of image_source_script specify an image name. However, both
use the deprecated @ syntax, indicating that they have not been updated
in a while. If CONFIG_FIT_SIGNATURE is enabled, we will reject such
names outright. Back in commit 152576a598 ("stm32mp: stm32prog: handle
U-Boot script in flashlayout alternate"), we even renamed one of the
nodes. Instead of hard-coding a script image name, just use the default
image.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Documentation:
* Reorganize existing TI docs and add K3 generation page
* Add texinfodocs and infodocs targets
* Update qemu-ppce500 documentation
* Use "changesets" not "csets" in statistics pages
UEFI
* Fix merging of preseeded non-volatile variables
* Fix a return value in the EFI_HII_DATABASE_PROTOCOL
* Set UEFI specification version to 2.10
-----BEGIN PGP SIGNATURE-----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=z7b8
-----END PGP SIGNATURE-----
Merge tag 'efi-2023-01-rc5-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2023-01-rc5-2
Documentation:
* Reorganize existing TI docs and add K3 generation page
* Add texinfodocs and infodocs targets
* Update qemu-ppce500 documentation
* Use "changesets" not "csets" in statistics pages
UEFI
* Fix merging of preseeded non-volatile variables
* Fix a return value in the EFI_HII_DATABASE_PROTOCOL
* Set UEFI specification version to 2.10
In 96699f097a ("powerpc: mpc85xx: Use binman to embed dtb inside
U-Boot") we introduce CONFIG_MPC85XX_HAVE_RESET_VECTOR and do so via
Kconfig. However, much later in de47ff5363 ("Convert
CONFIG_SYS_MPC85XX_NO_RESETVEC to Kconfig") I converted the symbol that
is the inverse of this to Kconfig. This should have included a
dependency on the first symbol as they are logically opposite.
The dependency being missing lead to some platforms being broken at
runtime due to discarding the require reset vector.
Fixes: de47ff5363 ("Convert CONFIG_SYS_MPC85XX_NO_RESETVEC to Kconfig")
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Pali Rohár <pali@kernel.org>
For the 64bit EFI binaries that we create set the
IMAGE_FILE_LARGE_ADDRESS_AWARE characteristic in the PE-COFF header
to indicate that they can handle addresses above 2 GiB.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
A number of CONFIG symbols have crept in that are never referenced in
code, so drop them here. Further, we have two symbols being enabled
in headers while already enabled correctly in Kconfig, so these lines
can also be removed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Perform simple renames of:
CONFIG_WATCHDOG_PRESC to CFG_WATCHDOG_PRESC
CONFIG_WATCHDOG_RC to CFG_WATCHDOG_RC
Signed-off-by: Tom Rini <trini@konsulko.com>
As of 2f41ade79e ("linker: Modify linker scripts to be more generic")
we can use the same linker script for SPL and TPL and not have to make
use of #undef tricks. Remove these last remnants.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The way that the timer support is currently done for exynos/nexell
platforms relies on the legacy PWM infrastructure, and that needs to be
updated. However, we really cannot safely undef CONFIG_DM_PWM to build
the timer.c file without warnings. For now, rename the relevant legacy
functions to be prefixed with s5p_ and add prototypes to the arch pwm.h
files.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All vector instructions on powerpc mpc85xx must not be used because U-Boot
does not enable them. Usage cause random crashes. SPE vector instructions
are already disabled by compiler flags, so disable also AltiVec and VSX
vector instructions.
Linux kernel disables AltiVec and VSX instructions too.
Signed-off-by: Pali Rohár <pali@kernel.org>
Specifying -mspe=no also disables usage of SPE instructions. It is
documented in "[PATCH,rs6000] make -mno-spe work as expected" email:
http://gcc.gnu.org/ml/gcc-patches/2008-04/msg00311.html
So replace -mspe=yes by -mspe=no, so make it clear that u-boot has to be
compiled without SPE instructions.
Linux kernel contains following Makefile code to achieve it:
# No SPE instruction when building kernel
# (We use all available options to help semi-broken compilers)
KBUILD_CFLAGS += $(call cc-option,-mno-spe)
KBUILD_CFLAGS += $(call cc-option,-mspe=no)
Do same for U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
When gcc's default cpu (selected by --with-cpu= during gcc's configure
phase) does not match target U-Boot board cpu then U-Boot binary does not
have to be compiled correctly. Lot of distributions sets gcc's default cpu
to generic powerpc variant which works fine.
U-Boot already pass -Wa,-me500 flag to gcc which instructs GNU AS to accept
e500 specific instructions when processing assembler source files (.S).
This affects also assembly files generated by gcc from C source files. And
because gcc for generic powerpc cpu puts '.machine ppc' at the beginning of
the generated assembly file, it basically overwrites -me500 flag by which
was GNU AS invoked (from U-boot build system).
It started to be an issue since binutils 2.38 which does not keep enabled
extra functional units selected by previous cpu. Hence issuing directive
'.machine ppc' (generated by gcc for generic powerpc) after '.machine e500'
(specifying at command line) disables usage of e500 specific instructions.
And compiling arch/powerpc/cpu/mpc85xx/tlb.c code throws following
assembler errors:
{standard input}: Assembler messages:
{standard input}:127: Error: unrecognized opcode: `tlbre'
{standard input}:418: Error: unrecognized opcode: `tlbre'
{standard input}:821: Error: unrecognized opcode: `msync'
{standard input}:821: Error: unrecognized opcode: `tlbwe'
{standard input}:884: Error: unrecognized opcode: `tlbsx'
This issue was already hit by Debian people and is reported in bug tracker:
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1003490
Calling gcc with -mcpu=8540 flag fixes this issue because -mcpu=8540 tells
gcc to compile code for e500 core/cpu (overwriting gcc's default cpu) and
does not put '.machine ppc' directive into assembly anymore.
Also if gcc is invoked with -mcpu=8540 then it pass -me500 flag to GNU AS.
So it is unnecessary to manually specify -Wa,-me500 flag because it is
implicitly added.
Fix this issue properly by specifying correct -mcpu compiler flag for all
supported powerpc cores in U-Boot mpc85xx platform, which are: e500v1,
e500v2, e500mc, e5500 and e6500. For specifying e500v1 and e500v2 cores,
gcc has unintuitive -mcpu=8540 and -mcpu=8548 flag names, for other cores
-mcpu matches core name.
The only difference between gcc's -mcpu=8540 and -mcpu=8548 flags is
support for double precision floating point SPE instructions. As U-Boot
does not use floating point, it is fine to use -mcpu=8540 for both e500v1
and e500v2 cores. Moreover gcc 9 completely removed e500 floating point
support, so since gcc 9 -mcpu=8548 is just alias to -mcpu=8540.
Note that U-Boot's CONFIG_E500 option is set also for other cpus, not only
for e500v1 and e500v2. So do not check for CONFIG_E500 and rather set e500
as last fallback value when no other mpc85xx cpu matches.
Signed-off-by: Pali Rohár <pali@kernel.org>
At this point only the TARGET_T1042D4RDB variant of this is supported in
tree, so remove the remaining parts of the other platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_TEGRA_ENABLE_UARTA
CONFIG_TEGRA_ENABLE_UARTB
CONFIG_TEGRA_ENABLE_UARTC
CONFIG_TEGRA_ENABLE_UARTD
CONFIG_TEGRA_SPI
CONFIG_TEGRA_UARTA_GPU
CONFIG_TEGRA_UARTA_SDIO1
CONFIG_TEGRA_VDD_CORE_TPS62361B_SET3
CONFIG_TEGRA_VDD_CORE_TPS62366A_SET1
Signed-off-by: Tom Rini <trini@konsulko.com>
Stop using CONFIG_SANDBOX_ARCH and use CONFIG_SANDBOX instead. For the
SPI related defines, set them directly in Kconfig. This now empties
arch/sandbox/include/asm/config.h.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this symbol to Kconfig, and preserve the current behavior. The
help text here comes from where the relevant code is implemented and it
is quite likely at this point in time we could either disable this
option or at least make it configurable.
Signed-off-by: Tom Rini <trini@konsulko.com>
When the ti814x_evm config was removed most, but not all, of the
relevant support code was remove. Get rid of what was missed.
Fixes: 50b5326868 ("ti814x: Remove platform")
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MONITOR_IS_IN_RAM
As part of this, reword some of the documentation slightly to reflect
that this is in Kconfig and not a define now.
Signed-off-by: Tom Rini <trini@konsulko.com>
The way all of the memory init code here works is that we pass
0xDEADBEEF around for the initial value (as it's a well known 'poison'
value and so easily recognized in debuggers, etc). The only point of
this CONFIG symbol was to pass in a different value for that purpose.
Drop this symbol and cleanup the code slightly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_GATEWAYIP
CONFIG_HOSTNAME
CONFIG_IPADDR
CONFIG_NETMASK
CONFIG_ROOTPATH
CONFIG_SERVERIP
CONFIG_UBOOTPATH
To do this, we introduce a CONFIG_USE_ form of each of the above and
change include/env_default.h to test for that to be set before setting a
value. Further, we don't want to stringify the IP address related values
as they are now properly strings via Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FLASH_SPANSION_S29WS_N
CONFIG_FLASH_VERIFY
CONFIG_FSL_FM_10GEC_REGULAR_NOTATION
CONFIG_FSL_ISBC_KEY_EXT
CONFIG_FSL_TRUST_ARCH_v1
CONFIG_FSL_SDHC_V2_3
CONFIG_MAX_DSP_CPUS
CONFIG_MIU_2BIT_INTERLEAVED
CONFIG_SERIAL_BOOT
CONFIG_SPI_BOOTING
CONFIG_X86EMU_RAW_IO
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_DM9000_BYTE_SWAPPED
CONFIG_DM9000_NO_SROM
CONFIG_DM9000_USE_16BIT
CONFIG_DM9000_DEBUG
CONFIG_MXC_GPT_HCLK
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is enabled for all exynos5 platforms, move to Kconfig and
select it.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The PMC node is not an interrupt provider, so it must not have
interrupt-cells.
This fixes the warning (on newer DTC):
arch/arm/dts/sama5d2.dtsi:82.22-602.6: Warning (interrupt_provider): /ahb/apb/pmc@f0014000: '#interrupt-cells' found, but node is not an interrupt provider
Fixes: 2c4b2dd289 ("ARM: at91/dt: Add device tree for SAMA5D2 Xplained")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add SAMA7G5 series chip id definitions to align with linux SoC driver.
Add support for SAMA7G5 System-In-Package (SIP):
SAMA7G54D1G, SAMA7G54D2G, SAMA7G54D4G.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Align the DT with current Linux 6.1 tree, wherever possible.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add information that will be needed for enabling the UEFI capsule
update feature on the RockPi4 boards. With the feature enabled, it
would be possible to update the idbloader and u-boot.itb images on the
RockPi4B and RockPi4C variants.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add functions needed to support the UEFI capsule update feature on
rockchip boards. Currently, the feature is being enabled on the
RockPi4 boards with firmware images residing on GPT partitioned
storage media.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The i2c locks up when initialized before relocation, and it stays broken
in Linux as well breaking the ability to boot Linux.
The i2c bus and pmic was not actually used in pre-reloc before
commit ad607512f5 ("power: pmic: rk8xx: Support sysreset shutdown method")
The cause is not known.
This is board-specific, other boards that do not add the option to
include the i2c bus in pre-reloc DT are not affected.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The GPT table is taking the first 34 sectors, which amounts to 0x4400
bytes. Saving the environment below this address in storage will corrupt
the GPT table.
While technically the table ends at 0x4400, some tools (e.g. bmaptool)
are rounding everything to the logical block size (0x1000), so it is
safer to make it point to 0x5000 so that the environment could still
persist when flashing a sparse image with bmaptool or similar tools.
Obviously, the default 0x4000 environment size does not work anymore, so
let's set it to 0x3000 so it does fill the gap between the GPT table
(rounded to 0x1000) and the start of the idbloader.img.
Fixes: 56f580d3eb ("rockchip: dts: rk3399-puma: put environment (in MMC/SD configurations) before SPL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move all rk3128 u-boot specific properties in separate dtsi files.
Sort emmc node.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3128
sync the clock dt-binding header.
This is the state as of v6.0 in Linux.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip platform use TPL to do the DRAM initialize for all the SoCs,
if TPL is not available, means no available DRAM init program, and the
u-boot-rockchip.bin is not functionable.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Change-Id: I2299f1eddce5aa7d5fb1a3fb4d8aeaa995b397fa
This cleans up each board's defconfig, and fixes the serial console on
some Olimex board. Also we lose another legacy config variable.
The rest are minor cleanups, that actually shouldn't change anything
in the build.
Passed the gitlab CI, plus briefly tested on Pine64-LTS, LicheePi Nano,
and BananaPi M1.
The legacy Allwinner code is cluttered with #ifdef's, some of them even
nested, which makes the code hard to read and error prone.
Eventually we will get rid of most of them, but for now let's at least
annotate the #endif lines with the corresponding symbol the bracket
started with.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When building U-Boot with clang, it notices that the i8259.h include
guard does not work correctly due to a typo. Fix it.
Signed-off-by: Alistair Delva <adelva@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The functions board_fit_image_post_process() and board_tee_image_process()
are not actually board specific (despite their names). Any board using the
OMAP2 family can use these functions. Move them to boot-common.c.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add OSPI Support such that this device can boot up using OSPI Flash.
Also can use the flash for other purposes if required from uboot.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Introduce the auto-generated clock tree and power domain data needed to
attach the am62a into the power-domain and clock frameworks of uboot
Signed-off-by: Bryan Brattlof <bb@ti.com>
Introduce the base dts files needed for u-boot or to augment the
linux dtbs for use in the u-boot-spl and u-boot binaries
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Introduce the basic am62a7 SoC dtbs from the v6.1-rc3 tag of the linux
kernel along with the new am62a specific pinmux definition that we will
use to generate the dtbs for the u-boot-spl and u-boot binaries
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
This function calls rtc_write32, which has a different signature
depending on if (SPL_)DM_RTC is enabled or not. This could result in a
mismatch in SPL if DM_RTC was enabled but SPL_DM_RTC, as the non-DM
declaration would still be used in SPL even though the implementation
would be for non-DM_RTC. We are switching to the correct definitions in
the next commit, so this will become a compilation error. Since
fsp_save_s3_stack is not called from SPL, avoid compiling it if
(SPL_)DM_RTC is disabled.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Enable the EBI and NAND flash controller. Define the pinctrl and
partition table
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
- Kautuk's semihosting patch:
move semihosting library from arm directory to common place and add
RISC-V support
- Zong's Kconfig patch:
use "imply" instead of "select" to allow user to decide if
SPL_SEPARATE_BSS should be selected
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmORqHQcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyF4qCACQZLl0WPPGOABtlJdB
7a5bZUwjeQdwES78Mx7N4pYAldafv+yBbzDHg/8fp3zS70xuMgqHmmDHgQ7GinvX
lOpFaWpxDTOkEOCn6+2x90mNpCh0siuCptUyaHfQ+B5L3leXqb3DTJuBLQyMbjAE
bhGjImPfZY+KdPY3VTkIK0fIZJD+/woysTSA5RCC8JmIUEHgPnOxes47gRCyKoug
sznMzYO5gGP7jpA9p1QXOLLiiAENQ+DxiCUdQDrDHm0PxTk8YQbhEiF0Svm476FL
hLuuuccCOzY1obCm9z70dDOhvmkH7tKHs02Es00nGEk2X+ZrI0oG0FtH4Z7CcZKF
WcWV
=PJWw
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.01-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 fixes for the 2023.01 cycle:
This is a single tiny fix that allows the correct name for one pin on
sama7g5 device. People with DT coming from Linux will have build errors
without this if they add NAND device.
Use imply instead of select, then it can still be disabled by
board-specific defconfig, or be set to n manually.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
We add RISC-V semihosting based serial console for JTAG based early
debugging.
The RISC-V semihosting specification is available at:
https://github.com/riscv/riscv-semihosting-spec/blob/main/riscv-semihosting-spec.adoc
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Kautuk Consul <kconsul@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
We factor out the arch-independent parts of the ARM semihosting
implementation as a common library so that it can be shared
with RISC-V.
Signed-off-by: Kautuk Consul <kconsul@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As DM_ETH is required for all network drivers, it's now safe to remove
the non-DM_ETH support code. Doing this removes some board support code
which was also unused. Finally, this removes some CONFIG symbols that
otherwise needed to be migrated to Kconfig, but were unused in code now.
Signed-off-by: Tom Rini <trini@konsulko.com>
We only need to enable DM_ETH if we have a networking driver. All
networking drivers depend on DM_ETH being enabled, and their selection
ensures DM_ETH will be enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
The pl18x MMCI driver does not use the interrupt-names property,
the binding document has been updated to recommend this property
be unused, remove it.
Backport of Marek's Linux patch:
https://lore.kernel.org/linux-arm-kernel/20221013221242.218808-3-marex@denx.de/
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Yann Gautier <yann.gautier@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
On STM32MP135F-DK, the SD card detect GPIO is GPIOH4.
Backport of the Linux patch:
https://lore.kernel.org/linux-arm-kernel/20220921160334.3227138-1-yann.gautier@foss.st.com/
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Adds support of Clock and Reset drivers for STM32MP13 platform.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
It is a bad idea, and more modern toolchains will fail, if you declare
an assembly function to be global and then weak, instead of declaring it
weak to start with. Update assorted assembly files to use the WEAK macro
directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Builiding with GCC 12.2 fails:
arch/powerpc/cpu/mpc85xx/liodn.c: In function 'fdt_fixup_liodn_tbl_fman':
arch/powerpc/cpu/mpc85xx/liodn.c:340:35: error: the comparison will
always evaluate as 'false' for the address of 'compat'
will never be NULL [-Werror=address]
340 | if (tbl[i].compat == NULL)
|
Remove the superfluous check.
Fixes: 97a8d010e0 ("net/fman: Support both new and legacy FMan Compatibles")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In practice, it is clear that the usage in m68k of
CONFIG_WATCHDOG_TIMEOUT is setting a value in milliseconds. Rename this
to the existing symbol and move to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
We move the existing CONFIG_POST_* functionality over to CFG_POST and
then introduce CONFIG_POST to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Given that we can use Kconfig logic directly to see if we have a program
available on the host or not, change from passing NO_SDL to instead
controlling CONFIG_SANDBOX_SDL in Kconfig directly. Introduce
CONFIG_HOST_HAS_SDL as the way to test for sdl2-config and default
CONFIG_SANDBOX_SDL on if we have that, or not.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This option controls using board/samsung/common/misc.c, so add a Kconfig
file there as well and select it from the boards which use this
functionality.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This is only used on sandbox, so select it there.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the SRIO namespace do not
easily transition to Kconfig. In many cases they likely should come from
the device tree instead. Move these out of CONFIG namespace and in to
CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SRIO1
CONFIG_SRIO2
CONFIG_SRIO_PCIE_BOOT_MASTER
CONFIG_SYS_SRIO
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_TIMER_COUNTS_DOWN
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_NOBQFMAN
CONFIG_SYS_DPAA_DCE
CONFIG_SYS_DPAA_FMAN
CONFIG_SYS_DPAA_PME
CONFIG_SYS_DPAA_RMAN
CONFIG_SYS_PMAN
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_PCI and
CONFIG_SYS_PCIE namespace do not easily transition to Kconfig. In many
cases they likely should come from the device tree instead. Move these
out of CONFIG namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_OMAP_ABE_SYSCK
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NUM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SPL_NS16550_MIN_FUNCTIONS
CONFIG_SYS_NS16550_MEM32
CONFIG_SYS_NS16550_PORT_MAPPED
CONFIG_SYS_NS16550_REG_SIZE
CONFIG_SYS_NS16550_SERIAL
To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that
platforms can enable the legacy driver here for SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the callback function we have to use memcpy(). Otherwise we add
the new samples on top of what is stored in the stream buffer.
If we don't have enough data, zero out the rest of the stream buffer.
Our sampling frequency is 48000. Let the batch size for the callback
function be 960. If we play a multiple of 20 ms, this will always be
a full batch.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Consider unexpected values for frequency:
* negative frequency
* zero frequency
* frequency exceeding sampling frequency
As in these cases the sum of the samples is zero also check the count of
the samples.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ZynqMP mini configurations are not using IPI driver and enabling this is
adding additional ~1200 Bytes (depends on configuration).
This ends up in situation that there is no enough space in OCM for
relocation that's why disable this driver for all mini configurations.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c71bab3927cb71ae517d9c21f59f3d5cf0caf712.1669734580.git.michal.simek@amd.com
The commit ed35de6170 ("Convert CONFIG_ZYNQMP_PSU_INIT_ENABLED to
Kconfig") converted CONFIG_ZYNQMP_PSU_INIT_ENABLED symbol and enabled it by
default which is not correct configuration.
Intention of this config was to have it enabled by default for SPL and
provide an option to users to also do low level initialization directly
from U-Boot.
That's why it is necessary to define second symbol with SPL marking in it
and properly use symbols depends on usage in Makefile.
Also disable ZYNQMP_PSU_INIT_ENABLED from boards which enables it by
default. CONFIG_SPL_ZYNQMP_PSU_INIT_ENABLED is enabled by default when SPL
is enabled.
Reported-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d5fcbd66b05bf0d7ef594e66464ee23b48c5e4cc.1669969083.git.michal.simek@amd.com
When Linux boot takes over control of the pmu
(by signaling PM_INIT_FINALIZE via ipi), pmu will switch off 'unused'
rpu cores. The Xilinx zynqmp fsbl prevents switching off those cores by
marking rpu cores as 'used' when loading code partitions to those cores.
The current u-boot SPL is missing this behaviour, which results in
halting rpu cores during Linux boot.
This commit mimics the xilinx zynqmp fsbl behavior by marking r5 cores as
used when they are released during boot.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Signed-off-by: Lukas Funke <lukas.funke-oss@weidmueller.com>
Link: https://lore.kernel.org/r/20221028121547.26464-2-lukas.funke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The SanCloud BBE requires the same dtb nodes to be present in the SPL as
the AM335x EVM.
The SanCloud BBE Lite also requires the SPI flash node and all
dependencies to be present in the SPL to support SPI boot.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
For successful boot when CONFIG_SPL_OF_CONTROL=y, we need to ensure that
the board EEPROM on i2c0, the uart0 serial port and the relevant boot
device (mmc1 or mmc2) can be accessed in the SPL. We also need to
preserve the parent nodes for each required dtb node.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The signal name of pin PD8 with function D is A22_NANDCLE
as it is defined in the datasheet.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Use macro to represent the RL and WL setting to ensure the PHY and
controller setting are aligned.
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
- Re-add the old PHY reset binding for nanopi-k2
-----BEGIN PGP SIGNATURE-----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=yEaP
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20221122' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Implement setbrg op to meson serial device
- Re-add the old PHY reset binding for nanopi-k2
The sync of device-tree/bindings in 11a48a5a18c6 ("Linux 5.6-rc2") causes
Ethernet to break on some GXBB boards; the PHY seems to need proper reset
timing to function in u-boot and Linux. Re-add the old PHY reset binding
for dwmac until we support new bindings in the PHY node. This borrows the
same fix applied to the Odroid C2 board [0].
[0] https://lists.denx.de/pipermail/u-boot/2021-April/446658.html
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20221025143205.14470-1-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support octal spi flash and uses DCC terminal
for console output. Add required dts for octal spi flash mini u-boot
configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support qspi flash and uses DCC terminal
for console output. Add required dts files for qspi mini configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add soc_xilinx_versal_net driver to identify the family & revision of
versal-net SoC. Add Kconfig option CONFIG_SOC_XILINX_VERSAL_NET to
enable/disable this driver. To enable this driver by default, add this
config to xilinx_versal_net_virt_defconfig file. This driver will be
probed using platdata U_BOOT_DEVICE structure which is specified in
mach-versal-net/cpu.c.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/613d6bcffd9070f62cf348079ed16c120f8fc56f.1668612993.git.michal.simek@amd.com
The fclk-enable property is set to 0 which disables all FCLKs.
Enable all FCLKs so they can be used as clock sources in the
programmable logic.
Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b1308dc1f14f8eb24662019f7376c959e5e763b8.1665567031.git.michal.simek@amd.com
Removing the zynq_board_read_rom_ethaddr() function as
xlnx,eeprom is not used anymore. As all board dts to use
nvmem alias instead of xlnx,eeprom.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221017094818.17996-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Apply commit 534f0fbd65 ("arm64: Fix relocation of env_addr if
POSITION_INDEPENDENT=y") also for 32-bit ARM.
This change fixes crashing of U-Boot on ARMv7 (Omap3 / Cortex-A8) Nokia N900
phone (real HW). Note that qemu emulator of this board with same u-boot.bin
binary has not triggered this crash.
Crash happened after U-Boot printed following debug lines to serial console:
initcall: 0001ea8c (relocated to 8fe0aa8c)
Loading Environment from <NULL>... Using default environment
Destroy Hash Table: 8fe25a98 table = 00000000
Create Hash Table: N=387
Signed-off-by: Pali Rohár <pali@kernel.org>
Describe that CONFIG_SBI_V02=y does not mean SBI specification v0.2
but v0.2 or later.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We should check the string until it hits underscore, in case it
searches multi-letter extensions. For example, "rv64imac_xandes"
will be treated as D extension support since there is a "d" in
"andes", resulting illegal instruction caused by initializing FCSR.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The initial devicetree for PolarFire SoC incorrectly created a fixed
frequency clock in the devicetree to represent the msspll, but the
msspll is not a fixed frequency clock. The actual reference clock on a
board is either 125 or 100 MHz, 125 MHz in the case of the icicle kit.
Swap the incorrect representation of the msspll out for the actual
reference clock.
Fixes: dd4ee416a6 ("riscv: dts: Add device tree for Microchip Icicle Kit")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
We should guard the SPL nodes against CONFIG_SPL_BUILD to fix
the following build error when the blobs are absent:
binman: Fail open first container file mx8qm-ahab-container.img
Signed-off-by: Fabio Estevam <festevam@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_NONCACHED_MEMORY
To do this we introduce CONFIG_SYS_HAS_NONCACHED_MEMORY as a bool to
gate if we are going to have noncached_... functions available and then
continue to use CONFIG_SYS_NONCACHED_MEMORY to store the size of said
cache. We make this new option depend on both the architectures which
implement support and the drivers which make use of it.
Cc: Tom Warren <twarren@nvidia.com>
Cc: Mingming lee <mingming.lee@mediatek.com>
Cc: "Ying-Chun Liu (PaulLiu)" <paul.liu@linaro.org>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These files reference SZ_ macros without including <linux/sizes.h>,
correct this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce three options, one for each observed L3 cache size, and have
the size select'd as needed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce two options, one for each observed L2 cache size, and have the
size select'd as needed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_INIT_RAM_LOCK
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Switch to use binman to pack images
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Originally, the mmc aliases node was present in imx6qdl-wandboard.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a regression in which the SD card cannot be found anymore:
Since commit the aliases node has been removed
U-Boot 2022.10-00999-gcca41ed3d63f-dirty (Nov 03 2022 - 22:07:38 -0300)
CPU: Freescale i.MX6QP rev1.0 at 792 MHz
Reset cause: POR
DRAM: 2 GiB
Core: 62 devices, 17 uclasses, devicetree: separate
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the SD card (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Note: Nowadays, the intent is for them regular device trees to just be
synchronised from them Linux kernel device trees and any and all U-Boot
specific changes need to go into the -u-boot.dtsi device tree include
files which BTW get included automatically by the U-Boot build system.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Migrate to using automatic build system included -u-boot.dtsi device
tree include files.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Add support for the MSC SM2S-IMX8PLUS SMARC Module. Tested in conjunction
with the MSC SM2-MB-EP1 Mini-ITX Carrier Board.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Update the sandbox implementation to use UCLASS_HOST and adjust all
the pieces to continue to work:
- Update the 'host' command to use the new API
- Replace various uses of UCLASS_ROOT with UCLASS_HOST
- Disable test_eficonfig since it doesn't work (this should have a unit
test to allow this to be debugged)
- Update the blk test to use the new API
- Drop the old header file
Unfortunately it does not seem to be possible to split this change up
further.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running unit tests, some may have side effects which cause a
subsequent test to break. This can sometimes be seen when using 'ut dm'
or similar.
Add a new argument which allows a particular (failing) test to be run
immediately after a certain number of tests have run. This allows the
test causing the failure to be determined.
Update the documentation also.
Signed-off-by: Simon Glass <sjg@chromium.org>
In order to boot over USB, the device tree needs to enable
a few extra nodes in SPL. Since the USB driver has the
ability to detect host/device, the dr_mode can be removed
from the device tree since it needs to act as a device when
booting and OTG is the default mode. Add USB boot support
to spl_board_boot_device and enable the corresponding config
options.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The e10133 workaround was broken in two places:
- The code intended to temporarily mask all interrupts in GPC_IMRx_CORE0.
While the old register values were saved, the actual masking was
missing.
- imx_udelay() expects the system counter to run at its base frequency,
but the system counter is switched to a lower frequency earlier in
psci_system_suspend(), leading to a much longer delay than intended.
Replace the call with an equivalent loop (linux-imx 5.15 does the same)
This fixes the SoC hanging forever when there was already a wakeup IRQ
pending while suspending.
Fixes: 57b620255e ("imx: mx7: add system suspend/resume support")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
This enables armv8 crypto extension usage for SHA1/SHA256.
Which speed up sha1/sha256 operations, about 10x faster with
a imx8mm evk for a 20MiB kernel hash verification (12ms vs 165ms).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The RD-AC5X-32G16HVG6HLG-A0 development board main components and
features include:
* Main 12V/54V power supply
* 270 Gbps throughput packet processor on the main board
* DDR4:
* SR1: 2GB DDR4 2400MT/S(1GB x 2 pcs ) with ECC(1GB x 1 pcs)
* SR2: 4GB DDR4 2400MT/S(2GB x 2 pcs ) with ECC(2GB x 1 pcs)
* PCB co-layout with 4GB device to support 8GB (Dual CS) requirement
* 16GB eMMC (Samsung KLMAG1JETD-B041006)
* 16MB SPI NOR(GD25Q127C)
* 32 x 1000 Base-T interfaces
* 16 x 2500 Base-T interfaces
* SR1: 88E2540*4
* SR2: 88E2580*1+88E2540*2
* Six (6) x 25G Base-R SFP28 interfaces
* One (1) x RJ-45 console connector, interfacing to the on board UART
* One (1) x USB Type-A connector, interfacing to the USB 2.0 port (0)
* One (1) x USB Type-mini B connector, interfacing to the USB 2.0 port (1)
* One (1) x RJ-45 1G Base-T Management port, interfacing to the host
port (shared with PCIe) Connected to 88E1512 Gigabit Ethernet Phy
* One (1) x Oculink port, interfacing to the PCIe port for external CPU
connection
* POE 802.3AT support on Port 1 ~ Port 32, 802.3BT support on Port 33 ~
Port 48 (Microsemi PD69208T4, PD69208M or TI TPS2388,TPS23881
solution)
* POE total power budget 780W
* LED interfaces per network port/POE
* LED interfaces (common) showing system status
* PTP TC mode Supported (Reserved M.2 connector to support BC mode)
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
an integrated CPU (referred to as the CnM block in Marvell's
documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
has been ported from Marvell's SDK which is based on a much older
version of U-Boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The 64-bit mvebu SoCs don't have a suitable timer driver so add a !ARM64
condition to the select.
Fixes: 7b530bb19e ("arm: mvebu: Use CONFIG_TIMER on all MVEBU & KIRKWOOD platforms")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The uart1 node was missing the 'clock-frequency' property. This meant
the driver for this device would fail at probe.
The clock for uart1 is fed from the same source as uart0 and is a fixed
200MHz clock. This is confirmed via documentation for the CN9130 SoC
and from the equivalent code in Linux at:
<linux>/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
where uart0 and uart1 share a common 'clocks' definition.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add QSPI NAND device node to the Microchip PolarFire SoC
Icicle kit device tree.
The Winbond NAND flash memory can be connected to the
Icicle Kit by using the Mikroe Flash 5 click board and
the Pi 3 Click shield.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
In the v2022.10 Icicle reference design, the seg registers have been
changed, resulting in a required change to the memory map.
A small 4MB reservation is made at the end of 32-bit DDR to provide some
memory for the HSS to use, so that it can cache its payload between
reboots of a specific context.
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
As PLICSW is used to trigger the software interrupt, we should rename
Andes PLIC configuration and file name to reflect the usage. This patch
also updates PLMT and PLICSW compatible strings to be consistent with
OpenSBI fdt driver.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_SYS_MIPS_TIMER_REQ
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Resolve all uses of CONFIG_SYS_MHZ with the currently defined value.
Remove code which depends on CONFIG_SYS_MHZ but where no board configs
actually use that code.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add the needed bus mappings for the two main RTI memory ranges and
the required device tree nodes in the main domain.
Same as kernel commit 6dd8457dc20693e2ba9054c171499b22664fd4e7
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
So far the Calxeda machines were using the CONFIG_SYS_TIMER_* macros to
simply hardcode the address of the counter register of the SP804 timer.
This method is deprecated and scheduled for removal.
Use the newly introduced SP804 DM_TIMER driver to provide timer
functionality on Highbank and Midway machines. The base address and base
frequency are taken from the devicetree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently our semihosting trap function is somewhat fragile: we rely
on the current compiler behaviour to assign the second inline assembly
argument to the next free register (r1/x1), which happens to be the
"addr" argument to the smh_trap() function (per the calling convention).
I guess this is also the reason for the noinline attribute.
Make it explicit what we want: the "addr" argument needs to go into r1,
so we add another register variable. This allows to drop the "noinline"
attribute, so now the compiler beautifully inlines just the trap
instruction directly into the calling function.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit f4b540e25c5c("arm: smh: Fix uninitialized parameters with newer
GCCs") added a memory clobber to the semihosting inline assembly trap
calls, to avoid too eager GCC optimisation: when passing a pointer, newer
compilers couldn't be bothered to actually fill in the structure that it
pointed to, as this data would seemingly never be used (at least from the
compiler's point of view).
But instead of the memory clobber we need to tell the compiler that we are
passing an *array* instead of some generic pointer, this forces the
compiler to actually populate the data structure.
This involves some rather hideous cast, which is best hidden in a macro.
But regardless of that, we actually need the memory clobber, but for two
different reasons: explain them in comments.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARM semihosting interface uses different trap instructions for
different architectures and instruction sets. So far we were using
AArch64 and ARMv7-M, and had an untested v7-A entry. The latter does
not work when building for Thumb, as can be verified by using
qemu_arm_defconfig, then enabling SEMIHOSTING and SYS_THUMB_BUILD:
==========
{standard input}:35: Error: invalid swi expression
{standard input}:35: Error: value of 1193046 too large for field of 2 bytes at 0
==========
Fix this by providing the recommended instruction[1] for Thumb, and
using the ARM instruction only when not building for Thumb. This also
removes some comment, as QEMU for ARM allows to now test this case.
Also use the opportunity to clean up the inline assembly, and just define
the actual trap instruction inside #ifdef's, to improve readability.
[1] https://developer.arm.com/documentation/dui0471/g/Semihosting/The-semihosting-interface?lang=en
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add test cases for accessing the FWU Metadata on the sandbox
platform. The sandbox platform also uses the metadata access driver
for GPT partitioned block devices.
The FWU feature will be tested on the sandbox64 variant with a raw
capsule. Remove the FIT capsule testing from sandbox64 defconfig --
the FIT capsule test will be run on the sandbox_flattree variant.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The FWU Multi Bank Update feature allows the platform to boot the
firmware images from one of the partitions(banks). The first stage
bootloader(fsbl) passes the value of the boot index, i.e. the bank
from which the firmware images were booted from to U-Boot. On the
STM32MP157C-DK2 board, this value is passed through one of the SoC's
backup register. Add a function to read the boot index value from the
backup register.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
The FWU metadata structure is accessed through the driver model
interface. On the stm32mp157c dk2 and ev1 boards, the FWU metadata is
stored on the uSD card. Add the fwu-mdata node on the u-boot specifc
dtsi file for accessing the metadata structure.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Use binman to build an image which includes all the U-Boot phases so that
a full VBE boot can take place with just that image.bin file. Attach the
image file to mmc2 so it can be loaded.
VBE is used to load images in two phases:
- In VPL, VBE decides which SPL image to load
- In SPL, VBE decides which U-Boot image to load
The latter should really be determined by VPL, since it does the full
signature verification on the selected configuration. However, we have
separate configurations for SPL and U-Boot proper, so for now we keep it
simple and have SPL do its own verification. This will need to be
tidied up later.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we put the driver in the /chosen node in U-Boot. This is a bit
strange, since U-Boot doesn't normally use that node itself. It is better
to put it under the bootstd node.
To make this work we need to copy create the node under /chosen when
fixing up the device tree. Copy over all the properties so that fwupd
knows what to do.
Update the sandbox device tree accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox runs the next phase from discrete executables, so for
example u-boot-tpl runs u-boot-vpl to get to the next phase.
In some cases the phases are all built into a single firmware image, as is
done for real boards. Add support for this to sandbox.
Make it higher priority so that it takes precedence over the existing
method.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the sandbox executable is assumed to be arg[0] but this only
works for a single jump (e.g. from SPL to U-Boot). Add a new arg to solve
this issue, along with a detailed comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox only supports jumping to a file, to get to the next
U-Boot phase. We want to support other methods, so update the code to
use an enum for the method. Also use the
Use board_boot_order() to set the order, so we can add more options.
Also add the MMC methods into the BOOT_DEVICE enum so that booting
from MMC can be supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
This happens every time sandbox moves to the next phase so is not very
interesting. Display the message only when debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present we normally write tests either in Python or in C. But most
Python tests end up doing a lot of checks which would be better done in C.
Checks done in C are orders of magnitude faster and it is possible to get
full access to U-Boot's internal workings, rather than just relying on
the command line.
The model is to have a Python test set up some things and then use C code
(in a unit test) to check that they were done correctly. But we don't want
those checks to happen as part of normal test running, since each C unit
tests is dependent on the associate Python tests, so cannot run without
it.
To acheive this, add a new UT_TESTF_MANUAL flag to use with the C 'check'
tests, so that they can be skipped by default when the 'ut' command is
used. Require that tests have a name ending with '_norun', so that pytest
knows to skip them.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
As STI timer is renamed to ARM A9 global timer, change BCM63138 to use
the new global timer config symbol name.
This patch applies on top of the my previous patch [1].
[1]: https://lists.denx.de/pipermail/u-boot/2022-August/491060.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6753 is essentially same as the main chip BCM6855 but with different
SKU number. Now that BCM6855 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6855, remove the original ARCH_BCM6753 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm96753ref board folder. It is replaced by the
generic bcmbca board folder.
- Merge the 6753.dtsi setting to the new 6855.dtsi file. Update
96753ref board dts with the new compatible string.
- Delete broadcom_bcm96763ref.h and merge its setting to the new
bcm96855.h file.
- Delete bcm96753ref_ram_defconfig and use a basic config version of
bcm96855_defconfig
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6855 is a Broadcom ARM A7 based PON Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
broadband SoC, this patch adds it under CONFIG_BCM6855 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL101 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM6858 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6858, remove the original ARCH_BCM6858 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm968580xref board folder. It is replaced by the generic
bcmbca board folder.
- Update bcm968580xref board dts with the new compatible string.
- Delete broadcom_bcm968580xref.h and merge its setting to the new
bcm96858.h file.
- Remove bcm968580xref_ram_defconfig as a basic config version of
bcm96858_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6858 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other broadband
SoC, this patch adds it under CONFIG_BCM6858 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and the
original dts is updated with the one from linux next git repository.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM68360 is a variant within the BCM6856 chip family. Now that BCM6856
is supported under CONFIG_ARCH_BCMBCA and CONFIG_BCM6856, remove the
original ARCH_BCM68360 support and migrate its configuration and dts
settings. This includes:
- Remove the bcm968360bg board folder. It is replaced by the generic
bcmbca board folder.
- Merge the 68360.dtsi setting to the new 6856.dtsi file. Update board
dts with the new compatible string.
- Merge broadcom_bcm968360bg.h setting to the new bcm96856.h file.
- Remove bcm968360bg_ram_defconfig as a basic config version of
bcm96856_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6856 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other Broadband
SoC, this patch adds it under CONFIG_BCM6856 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and Broadcom uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM63158 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM63158, remove the original ARCH_BCM63158 support and migrate
configuration settings.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63158 is a Broadcom B53 based DSL Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
Broadband SoC, this patch adds it under CONFIG_BCM63158 chip
config and CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL011 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM4908 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added
under ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux git repository so the dts and dtsi
files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM6813 is a Broadcom B53 based PON and WLAN AP router SoC. It is part
of the BCA (Broadband Carrier Access origin) chipset family so it's
added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4912 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts
and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63146 is a Broadcom B53 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63138 is an ARM A9 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory, ARM A9 global timer
and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
This patch applies on top of the my previous patch [1].
[1] https://lists.denx.de/pipermail/u-boot/2022-August/490570.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63148 is an Broadcom B15 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6756 is an ARM A7 based WLAN Gateway and Access Point Broadband SoC.
It is part of the BCA(Broadband Carrier Access origin) chipset family so
it's added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6878 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011
uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6846 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM63178 is an ARM A7 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCY17nfA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPPoAJ0UYyt3kwslUlAJhOC+KU9UlYnVuwCbBXIQyBua
K5clq+GyxXfaDl2Hnvc=
=XXVp
-----END PGP SIGNATURE-----
Merge tag 'video-20221030' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix [hv]sync active vs back porch in dw_mipi_dsi
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
This is actually a panel, not a video device. Rename the option, move it
into the right place and make it depend on PANEL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently sandbox configuration defautls to 64bit and there is no
automation for building 32bit sandbox on 32bit hosts.
Use _LP64 macro as heuristic for detecting 64bit targets.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The jmp_buf type is required by the C99 specification.
Defining it for x86 fixes building the longjmp unit test.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If longjmp(jmp_buf env, int val) is called with val = 0, the setjmp()
macro must return 1.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- nuvoton: add expire function for generic reset (Jim)
- handle watchdogs during keyed autoboot (Rasmus)
- cyclic: Don't disable cylic function upon exceeding CPU time (Stefan)
- ulp wdog: Updates to support iMX93 and DM (Alice)
Layerscape update
- support sysreset,
- de-select FSL_IFC when booting from SD
- disable unused parts of ICID tables
- reduce ns_dev size for csu
- enable dma snooping for ls104x
- nand driver fixups for ls1043ardb rev 7.0 boards.
Avoid the following build errors after the device tree sync:
drivers/spi/mxs_spi.c: In function ‘mxs_spi_probe’:
drivers/spi/mxs_spi.c:327:25: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘spi_max_frequency’
327 | priv->max_freq = dtplat->spi_max_frequency;
| ^~
drivers/spi/mxs_spi.c:328:23: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘num_cs’
328 | plat->num_cs = dtplat->num_cs;
| ^~
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
