Resend mailbox command for 3 times with 2ms interval in between if
it receives MBOX_RESP_TIMEOUT and MBOX_RESP_DEVICE_BUSY response code.
Add a wrapper function mbox_send_cmd_common_retry() for retry, change
all the callers to use this wrapper function.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Sync latest mailbox response codes from SDM firmware.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Mailbox command which is too large to fit into the mailbox
FIFO command buffer can be sent to SDM in multiple parts.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Mailbox driver should always check for the length of the response
and read the response data before returning the response status to
caller.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add miliseconds delay when waiting for mailbox event to happen
before timeout. This will ensure the timeout duration is predictive.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Document down the usage of boot_scratch_cold register to avoid
overlapping of usage in the code for S10 & Agilex.
The boot_scratch_cold register is generally used for passing
critical system info between SPL, U-Boot and Linux.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enable FPGA full reconfiguration support with Intel FPGA SDM
Mailbox driver for Agilex.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename Stratix10 FPGA driver to Intel FPGA SDM Mailbox driver
because it is using generic SDM (Secure Device Manager) Mailbox
interface shared by other platform (e.g. Agilex) as well.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
All SoCFPGA platforms (except Cyclone V) are now switching
to CONFIG_WDT (driver model for watchdog timer drivers)
from CONFIG_HW_WATCHDOG.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Print reset state (warm/cold) together with the
source (watchdog/MPU) which has triggered the warm
reset on S10 & Agilex.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Include SDM triggered warm reset bit (BIT1) in Reset Manager's stat
register when checking for HPS warm reset status.
Refactor the warm reset mask macro for clarity purpose.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename the driver from S10 to SoC64 because Intel Agilex platform
also using the this SYSRESET SoCFPGA driver for S10.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Timer only need to be initialized once in SPL.
This patch remove the redundancy of initializing the
timer again in U-Boot proper
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
'dwmac_socfpga' driver will setup the PHY interface during probe.
PHY interface setup in arch_misc_init() is no longer needed.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Now that PIE works when U-Boot is started from ROM, let's enable
CONFIG_POSITION_INDEPENDENT, which allows to load U-Boot also via
ARM Trusted-Firmware's fip.bin to DRAM, without tweaking the
configuration.
To get a writable initial stack, we need to keep the fixed initial
stack pointer, which points to DRAM in our case.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
CONFIG_ARCH_SUPPORT_TFABOOT was used on the qemu-arm64 platform to
guard a tweak to the flash bank configuration. U-Boot now reads the
current flash setup from the devicetree, so there is no need for
this option anymore.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently selecting CONFIG_POSITION_INDEPENDENT also forces us to use an
initial stack pointer relative to the beginning of the BSS section.
This makes some sense, because this should be writable memory anyway.
However the BSS section is not cleared or used until later in the
setup process (after relocation), so memory nearby might not be
available early enough to host the initial stack. This is an issue if
U-Boot is loaded from (Flash-)ROM, for instance.
Allow CONFIG_INIT_SP_RELATIVE to be turned off by a board's config, to
be able to select a fixed stack pointer, for instance in known good
DRAM.
This will help QEMU utilising PIE, when it's loaded to (Flash-)ROM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
When the actual offset between link and runtime address is zero, there
is no need for patching up U-Boot early when running with
CONFIG_POSITION_INDEPENDENT.
Skip the whole routine when the distance is 0.
This helps when U-Boot is loaded into ROM, or in otherwise sensitive
memory locations.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
When we build an arm64 target and enable POSITION_INDEPENDENT, we were
skipping our build-time dynamic relocation fixup routine (STATIC_RELA).
This was probably done because we didn't need it in this case, as the
PIE fixup routine in start.S would take care of that at runtime.
However when we now skip this routine (upon detecting that the fixup
offset is 0), this might lead to uninitialised pointers.
Remove the exception, so that we always do the build-time relocation.
NOTE: GNU binutils starting with v2.27.1 do this build-time relocation
automatically, to be in-line with other architecures. So on newer
toolchains our manual fixup is actually not needed. It doesn't hurt to
have it, though, so that we keep compatibility with the popular Linaro
toolchains, which lack this feature.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
The CONFIG_TFABOOT option is more about what U-Boot DOES NOT need to do
than to support some features.
Explain a bit more in the Kconfig help text to avoid misunderstandings.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a device tree binding for the BOOT button on the Maix board.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This patch adds the necessary device tree bindings.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Rick Chen <rick@andestech.com>
This modifies the existing led test to check for default led naming as
added in the previous patch.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This extends the pinctrl-sandbox driver to support pin muxing, and adds a
test for that behaviour. The test is done in C and not python (like the
existing tests for the pinctrl uclass) because it needs to call
pinctrl_select_state. Another option could be to add a command that
invokes pinctrl_select_state and then test everything in
test/py/tests/test_pinmux.py.
The pinctrl-sandbox driver now mimics the way that many pinmux devices
work. There are two groups of pins which are muxed together, as well as
four pins which are muxed individually. I have tried to test all normal
paths. However, very few error cases are explicitly checked for.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
to improve the maintainability. It is more easier to modify and add
configurations of the driver in the centralized ram driver directory.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAl9+Ie4ACgkQKPlOlyTy
XBg5lw//TEk6avR1/G4/SKe2Mj2hDQGm2OKjx5BLG6LC/m+It8lk5hFGCKeRTS3m
zlQ1z4Rki05Q/HW8fZfUSNZTGwbp1n5WJWMx5PRB2T4zYYeoktxQo6dRLbmR9mxL
2tiZ3QV3qzJafcwy1xdddr2GRGpRyu/sPHnEf5iHtijfT+6MPqSY5E1An+mAGhGb
IOjzh/OtmO+4Hu9zlp4G5AhNoQBBRRZg+2Sm+kVrzLyM345byucNpnnFiCT1T54M
iB3KsijBBvcnZ/bR7WMB+x942uFQi9hWdK0ngQhhOO4W1/Mf2ILst44gcxiJQNaf
dNIEdQxOeL1JDurQL/GSo4cQIr2mXlt3FtTB8RH8sAf9+aMJjlVqYaX3PGUFQJ5B
z5hnzKWk+jnxwD2F8fAtjqawQY6cBAaF/BDkxFdZcvhIIp9veUNDnk98YYwL7ZjU
8zRZQSmwI9zmC0kC9C6mmIN+eAbUhT+XDIlVk/USreujDkq9ESWIvo4SdY0+uXjJ
EJ1Xhqx/H7Qzem+SdbonJjMIWa/5rBnqT/nvCwSGDx64OdvD+F93RHFeyJvp8p1J
DWNNRZ4rAlrz3z8hDSuIt0M5ENoGWlHjD3nb11CBK/XnobBLhT+8W/b/ffjGcRnn
dowofymjvGMnhUUkHIb5heyMZaRCZVquGlEOIjrOdc4GNm6EW5Y=
=v+p3
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-10-07' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- mips: octeon: add support for DDR4 memory controller
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
Octeon needs a platform specific cmd to boot the Linux kernel, as
specific parameters need to be passed and special handling for the
multiple cores (SMP) is needed.
Co-developed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
[use gd->ram_base instead of gd->bd->bi_memstart]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is needed for Linux booting, as the memory infos need to be passed
in this bootmem format to the Linux kernel.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add header to handle bootinfo support, needed for Octeon Linux kernel
booting.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header includes the Octeon feature detection used in many Octeon
drivers.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header includes common register defines and accessor functions.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the necessary lowlevel init code, to enable SMP Linux
booting. This code will be used with the platform specific Octeon Linux
boot command "bootoctlinux", which starts a configurable number of cores
into Linux.
Additionally some erratas and lowlevel register initializations are
copied from the original Cavium / Marvell U-Boot source code, enabling
booting into the Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
As noticed while working on the USB xHCI support, Octeon needs to flush
all pending writes so that the values are present in the memory. Add
this "syncw" instruction (twice) to flush_dcache_range().
Signed-off-by: Stefan Roese <sr@denx.de>
Import platform specific mangle-port.h header, allowing a area specific
swapping, which is needed on Octeon for USB & PCI areas.
Imported from Linux v5.7.
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_should_swizzle_table[] which is needed for the area
specific swapping. It will be used by the platform specific
mangle-port.h header.
Imported from Linux v5.7.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the initialization call for the Octeon RAM driver to
the Octeon platforms code. So if enabled via Kconfig, the DDR driver
will be called and the RAM will be configured and used. If the RAM
driver is not enabled, the L2 cache is still used as RAM.
Signed-off-by: Stefan Roese <sr@denx.de>
This header will be used by the DDR driver (lmc). Its ported from the
2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header will be used by the DDR driver (lmc). Its ported from the
2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header is used by the upcoming DDR driver and potentially by other
drivers ported from the 2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the memory controller (LMC) DT node to the Octeon 3 dtsi
file. It also adds the L2C DT node, as this is referenced by the DDR
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
When using SDL for input the SDL key codes are first converted to Linux key
codes and then to matrix entries of the cross wired keyboard.
We must not map any key code to two different places on the keyboard. So
comment out one backslash position.
Update the rest of the file from Linux 5.7.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some blobs need a larger alignment than the default. For example, ACPI
tables often start at a 4KB boundary. Add support for this.
Update the size of the test blob to allow these larger records.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
-----BEGIN PGP SIGNATURE-----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=rbAX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
This imports the G12A & SM1 SoC and boards DT changes from the Linux
commit 9123e3a74ec7 ("Linux 5.9-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the correcly architectured USB Glue node for Meson AXG and the
S400 board in -u-boot.dtsi until support in upstream Linux then
backported.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the board_usb_init()/cleanup() for USB gadget for AXG based
on the code for the G12A architecture.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).
Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-gxl-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The USB support was initialy done with a set of PHYs and dwc3-of-simple
because the architecture of the USB complex was not understood correctly
at the time (and proper documentation was missing...).
But with the G12A family, the USB complex was correctly understood and
implemented correctly.
This adds a proper driver for the glue, based on the G12A one, but with
enough changes to require a different driver in U-Boot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This imports the AXG, GXL & GXM SoC and boards DT changes from the Linux
commit b3a9e3b9622a ("Linux 5.8-rc1").
This change also removes GXL & GXM u-boot.dtsi hacks for USB gadget.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
DT alignment with Linux kernel v5.9-rc4 for the STM32MP15x soc
device tree files and the STMicroelectronics boards device tree files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The u-boot,dm-spl DT props are missing on AV96, hence the pinmux and
flash0 nodes are not included in the reduced SPL DT. This prevents
SPI NOR boot from working at all. Fix this by filling them in.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add tests for SCMI reset controllers. A test device driver
sandbox-scmi_devices.c is used to get reset resources, allowing further
resets manipulation.
Change sandbox-smci_agent to emulate 1 reset controller exposed through
an agent. Add DM test scmi_resets to test this reset controller.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add tests for SCMI clocks. A test device driver sandbox-scmi_devices.c
is used to get clock resources, allowing further clock manipulation.
Change sandbox-smci_agent to emulate 3 clocks exposed through 2 agents.
Add DM test scmi_clocks to test these 3 clocks.
Update DM test sandbox_scmi_agent with load/remove test sequences
factorized by {load|remove}_sandbox_scmi_test_devices() helper functions.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change introduces SCMI agent uclass to interact with a firmware
using the SCMI protocols [1].
SCMI agent uclass currently supports a single method to request
processing of the SCMI message by an identified server. A SCMI message
is made of a byte payload associated to a protocol ID and a message ID,
all defined by the SCMI specification [1]. On return from process_msg()
method, the caller gets the service response.
SCMI agent uclass defines a post bind generic sequence for all devices.
The sequence binds all the SCMI protocols listed in the FDT for that
SCMI agent device. Currently none, but later change will introduce
protocols.
This change implements a simple sandbox device for the SCMI agent uclass.
The sandbox nicely answers SCMI_NOT_SUPPORTED to SCMI messages.
To prepare for further test support, the sandbox exposes a architecture
function for test application to read the sandbox emulated devices state.
Currently supports 2 SCMI agents, identified by an ID in the FDT device
name. The simplistic DM test does nothing yet.
SCMI agent uclass is designed for platforms that embed a SCMI server in
a firmware hosted somewhere, for example in a companion co-processor or
in the secure world of the executing processor. SCMI protocols allow an
SCMI agent to discover and access external resources as clock, reset
controllers and more. SCMI agent and server communicate following the
SCMI specification [1]. This SCMI agent implementation complies with
the DT bindings defined in the Linux kernel source tree regarding
SCMI agent description since v5.8.
Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The tests rely on a dummy driver to allocate and initialize the regmaps
and the regmap fields using the managed API. The first test checks if
the regmap config fields like width, reg_offset_shift, range specifiers,
etc work. The second test checks if regmap fields behave properly (mask
and shift are ok) by peeking into the regmap.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test to verify that GPIOs can be acquired/released using the managed
API. Also check that the GPIOs are released when the consumer device is
removed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
The tests are basically the same as for the regular API. Except that
the reset are initialized using the managed API, and no freed manually.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
This adds comments regarding the ordering and purpose of certain
instructions as I understand them.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
This ensures constructs like `if (gd & gd->...) { ... }` work when
accessing the global data pointer. Without this change, it was possible for
a very early trap to cause _exit_trap to directly or indirectly (through
printf) to read arbitrary memory. This could cause a second trap,
preventing show_regs from being printed.
printf (and specifically puts) uses gd to determine what function to print
with. These functions in turn use gd to find the serial device, etc.
However, before accessing gd, puts first checks to see if it is non-NULL.
This indicates an existing (perhaps undocumented) assumption that either gd
is NULL or it is completely valid.
Before this patch, gd either points to unexpected data (because it retains
the value it did from the prior-stage) or points to uninitialized data
(because it has not yet been initialized by board_init_f_init_reserve)
until the hart has acquired available_harts_lock. This can cause two
problems, depending on the value of gd->flags. If GD_FLG_SERIAL_READY is
unset, then some garbage data will be printed to stdout, but there will not
be a second trap. However, if GD_FLG_SERIAL_READY is set, then puts will
try to print with serial_puts, which will likely cause a second trap.
After this patch, gd is zero up until either a hart has set it in
wait_for_gd_init, or until it is set by arch_init_gd. This prevents its
usage before its data is initialized because both handle_trap and puts
ensure that gd is nonzero before using it. After gd has been set, it is OK
to access it because its data has been cleared (and so flags is valid).
XIP cannot use locks because flash is not writable. This leaves it
vulnerable to the same class of bugs regarding already-pending IPIs as
before this series. Fixing that would require finding another method of
synchronization, which is outside the scope of this series.
Fixes: 7c6ca03eae ("riscv: additional crash information")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We can reduce the number of instructions needed to use available_harts_lock
by using the aq and rl suffixes for AMOs.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Even though we no longer call smp_function if an IPI was not sent by
U-Boot, we still need to clear any IPIs which were pending from the
execution environment. Otherwise, secondary harts will busy-wait in
secondary_hart_loop, instead of relaxing.
Along with the previous commit ("riscv: Use a valid bit to ignore
already-pending IPIs"), this fixes SMP booting on the Kendryte K210.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Some IPIs may already be pending when U-Boot is started. This could be a
problem if a secondary hart tries to handle an IPI before the boot hart has
initialized the IPI device.
To be specific, the Kendryte K210 ROM-based bootloader does not clear IPIs
before passing control to U-Boot. Without this patch, the secondary hart
jumps to address 0x0 as soon as it enters secondary_hart_loop, and then
hangs in its trap handler.
This commit introduces a valid bit so secondary harts know when and IPI
originates from U-Boot, and it is safe to use the IPI API. The valid bit is
initialized to 0 by board_init_f_init_reserve. Before this, secondary harts
wait in wait_for_gd_init.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Without a matching barrier on the write side, the barrier in handle_ipi
does nothing. It was entirely possible for the boot hart to write to addr,
arg0, and arg1 *after* sending the IPI, because there was no barrier on the
sending side.
Fixes: 90ae281437 ("riscv: add option to wait for ack from secondary harts in smp functions")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Clearing MIP.MSIP is not guaranteed to do anything by the spec. In
addition, most existing RISC-V hardware does nothing when this bit is set.
The following commits "riscv: Use a valid bit to ignore already-pending
IPIs" and "riscv: Clear pending IPIs on initialization" should implement
the original intent of the reverted commit in a more robust manner.
This reverts commit 9472630337.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We currently do this in a u-boot specific dts, but hopefully we can get
these bindings added in Linux in the future.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The interrupt controller property is removed from the clint binding because
the clint is not an interrupt-controller. That is, no other devices have an
interrupt which is controlled by the clint.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This converts the clint driver from the riscv-specific interface to be a
DM-based UCLASS_TIMER driver. In addition, the SiFive DDR driver previously
implicitly depended on the CLINT to select REGMAP.
Unlike Andes's PLMT/PLIC (which AFAIK never have anything pass it a dtb),
the SiFive CLINT is part of the device tree passed in by qemu. This device
tree doesn't have a clocks or clock-frequency property on clint, so we need
to fall back on the timebase-frequency property. Perhaps in the future we
can get a clock-frequency property added to the qemu dtb.
Unlike with the Andes PLMT, the Sifive CLINT is also an IPI controller.
RISCV_SYSCON_CLINT is retained for this purpose.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
This merges the PLIC initialization code from two functions into one.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This converts the PLMT driver from the riscv-specific timer interface to be
a DM-based UCLASS_TIMER driver.
The clock-frequency/clocks properties are preferred over timebase-frequency
for two reasons. First, properties which affect a device should be located
near its binding in the device tree. Using timebase-frequency only really
makes sense when the cpu itself is the timer device. This is the case when
we read the time from a CSR, but not when there is a separate device.
Second, it lets the device use the clock subsystem which adds flexibility.
If the device is configured for a different clock speed, the timer can
adjust itself.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To test this function, sandbox CPU must set cpu_platdata.timebase_freq on
bind. It also needs to expose a method to set the current cpu. I also make
some most members of cpu_sandbox_ops static.
On the timer side, the device tree property
sandbox,timebase-frequency-fallback controls whether sandbox_timer_probe
falls back to time_timebase_fallback or to SANDBOX_TIMER_RATE.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The riscv-timer driver currently serves as a shim for several riscv timer
drivers. This is not too desirable because it bypasses the usual timer
selection via the driver model. There is no easy way to specify an
alternate timing driver, or have the tick rate depend on the cpu's
configured frequency. The timer drivers also do not have device structs,
and so have to rely on storing parameters in gd_t. Lastly, there is no
initialization call, so driver init is done in the same function which
reads the time. This can result in confusing error messages. To a user, it
looks like the driver failed when trying to read the time, whereas it may
have failed while initializing.
This patch removes the shim functionality from the riscv-timer driver, and
has it instead implement the former rdtime.c timer driver. This is because
existing u-boot users who pass in a device tree (e.g. qemu) do not create a
timer device for S-mode u-boot. The existing behavior of creating the
riscv-timer device in the riscv cpu driver must be kept. The actual reading
of the CSRs has been redone in the style of Linux's get_cycles64.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The following UEFI related issues are fixed:
* restore the global data pointer in the RISC-V trap handler
* install EFI_RNG_PROTOCOL only if we have a random number generator
* display human readable string for EFI_RNG_PROTOCOL in efidebug command
-----BEGIN PGP SIGNATURE-----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=W9Wz
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc6' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc6
The following UEFI related issues are fixed:
* restore the global data pointer in the RISC-V trap handler
* install EFI_RNG_PROTOCOL only if we have a random number generator
* display human readable string for EFI_RNG_PROTOCOL in efidebug command
The gp register is used to store U-Boot's global data pointer. We should
not assume that an UEFI application leaves the gp register unchanged as
the UEFI specifications does not define who is the owner of the gp and tp
registers.
So the following sequence should be followed in the trap handler:
* save the caller's gp register
* restore the global data pointer
* serve interrupts or print crash dump and reset
* restore the caller's gp register
Cc: Abner Chang <abner.chang@hpe.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Use "imply" instead of "select" for BOARD_EARLY_INIT_F config option,
and then disable it on boards which don't need it.
Updated grpeach_defconfig to disable CONFIG_BOARD_EARLY_INIT_F option for
RZA1.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Mark the default s_init function as weak, so that SoC's can
override it if needed, and it will still be discarded if unused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Add support to identify R8A7796 r1.3 SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965
Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF
accessible, mainline ATF is mandatory and must be built with
RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for
development and testing convenience only and must be disabled
in deployment for platform security reasons.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- Enhance the 'zboot' command to be more like 'bootm' with sub-commands
- The last series of ACPI core changes for programmatic generation of
ACPI tables
- Add all required ACPI tables for ApolloLake and enable ACPIGEN on
Chromebook Coral
- A feature minor enhancements to the 'hob' command
- Intel edison: Support for writing an xFSTK image via binman
It is useful to be able to flash Edison directly without relying on the
installed U-Boot being functional.
Add a binman image for this. It includes a 'OSIP' header (which happens to
look like an MBR / (Master-Boot Record), U-Boot binary and an environment.
I am not able to find a specification for OSIP.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We already use binman's 'multiple-images' feature with Chrome OS and we
want to use it for Edison. There is no real down-side.
Adjust x86 to always use multiple-images.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
At present the mtrr command only support 8 MTRRs. Some SoCs have more than
that. Update the implementation to support up to 10. Read the number of
MTRRs dynamically instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
GUIDs are one of the seven evils of the computer world. They obfuscate the
meaning and require people to look up long hex strings to decode it.
Luckily only a miniscule fraction of the 10^38 possible GUIDs are in use.
Add a way to decode the GUIDs known to U-Boot. Add a few more to the list
for good measure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable new features and provide require device-tree config so that U-Boot
produces the correct ACPI tables on Coral.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards want to reserve extra regions of memory. Add a 'chosen'
property to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this function only supports FSP-M but it is also used to read
FSP-S, in which case FSP-M may be zero. Add support for showing whichever
address is present in the FSP binary.
Also change the debug() statements to log_debug() while here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If locating the FSP header hangs for whatever reason it is useful to see
where it got stuck. Add a debug print. Also show the address of the FSP-S
entry point as a sanity check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This file doesn't currently have a log category. Add one so that items
are logged correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This provides information about a v1 TPM in the system. Generate this
table if the TPM is present.
Add a required new bloblist type and correct the header order of one
header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file cannot currently be included in ASL files. Add a header guard
to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is currently in the wrong place, so including the file in the device
tree fails. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Send this notification when U-Boot is about to boot into Linux, as
requested by the FSP.
Currently this causes a crash with the APL FSP, so leave it disabled for
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the MTRR registers are programmed with the list the U-Boot
builds up in the same order. In some cases this list may be out of order.
It looks better in Linux to have the registers in order, so sort them,
Signed-off-by: Simon Glass <sjg@chromium.org>
This new method is intended to be called when UEFI shuts down the 'boot
services', i.e. any lingering code in the boot loader that might be used
by the OS.
Add a definition for this new method and update the comments a little.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't have CONFIG_PCI in TPL but it is present in SPL, etc. So this
code is not needed. Drop it, and fix a code-style nit just above.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support generating a DMAR table and add a few helper routines as well.
Also set up NHLT so that audio works.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for generating various ACPI tables for Apollo Lake. Add a few
S3 definitions that are needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Apollo Lake needs to generate a few more table types used on Intel SoCs.
Add support for these into the x86 ACPI code.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are needed for the CPU tables. Add them into an x86-specific file
since we do not support them on sandbox, or include tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an implementation of the DBG2 (Debug Port Table 2) ACPI table.
Adjust one of the header includes to be in the correct order, before
adding more.
Note that the DBG2 table is generic but the PCI UART is x86-specific at
present since it assumes an ns16550 UART. It can be generalised later
if necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an implementation of the HPET (High Precision Event Timer) ACPI
table. Since this is x86-specific, put it in an x86-specific file
Signed-off-by: Simon Glass <sjg@chromium.org>
Add some more definitions to the iomap. These will be used by
ACPI-generation code as well as the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add SCI and power-state definitions required by ACPI tables. Fix the
license to match the original source file.
Als update the guard on acpi_pmc.h to avoid an error when buiding ASL.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot does not support SMM (System Management Mode) at present, but needs
a few definitions to correctly set up the ACPI table. Add these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Intel WiFi chips can use a common routine to write the information needed
by linux. Add an implementation of this.
Enable it for coral.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices can wake the system from sleep, e.g opening the lid on a
clamshell or moving a USB mouse.
Add a wake to specify this for USB devices and add the settings for Apollo
Lake.
Signed-off-by: Simon Glass <sjg@chromium.org>
Expand this to 4KB so that it is possible to add custom information to it.
On Chromebooks this is used to pass verified-boot information.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present U-Boot puts a magic number in the ASL for the GNVS table and
searches for it later.
Add a Kconfig option to use a different approach, where the ASL files
declare the table as an external symbol. U-Boot can then put it wherever
it likes, without any magic numbers or searching.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the definition of this structure common to Intel devices. It includes
some optional Chrome OS pieces which are used when vboot is integrated.
Drop the APL version as it is basically the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add common x86 ASL files, taken from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
When booting Chrome OS images the command line is stored separately
from the kernel. Add a way to specify this address so that images boot
correctly.
Also add comments to the zimage.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: adjust maxargs to 8 for 'zboot start']
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
There is a lot of information in the setup block and it is quite hard to
decode manually. Add a 'zboot dump' command to decode it into a
human-readable format.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the setup block is always obtained from the image
automatically. In some cases it can be useful to use a setup block
obtained elsewhere, e.g. if the image has already been unpacked. Add an
argument to support this and update the logic to use it if provided.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: adjust maxargs to 7 for 'zboot start']
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present it is not possible to tell from a script where the setup block
is, or where the image was loaded to. Add environment variables for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a subcommand that sets up the kernel ready for execution.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a subcommand that loads the kernel into the right places in memory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: adjust ZBOOT_STATE_INFO value to match the command order]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add a little subcommand that prints out where the kernel was loaded and
its setup pointer. Run it by default in the normal boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Split out the code that actually boots linux into a separate sub-command.
Add base_ptr to the state to support this.
Show an error if the boot fails, since this should not happen.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add subcommands to zboot. At present there is only one called 'start'
which does the whole boot. It is the default command so is optional.
Change the 's' string variable to const while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: reduce maxargs to 6 of 'zboot start' subcommand]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present if an error occurs while setting up the boot, interrupts are
left disabled. Move this call later in the sequence to avoid this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present U-Boot sets a loader type of 8 which means LILO version 8,
according to the spec. Update it to 0x80, which means U-Boot with no
particular version.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To help reduce the size and complexity of load_zimage(), move the code
that reads the kernel version into a separate function. Update
get_boot_protocol() to allow printing the 'Magic signature' message only
once, under control of its callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use IS_ENABLED() instead of #ifdef in this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the 'zboot' command does everything in one go. It would be
better if it supported sub-commands like bootm, so it is possible to
examine what will be booted before actually booting it.
In preparation for this, move the 'state' of the command into a struct.
This will allow it to be shared among multiple functions in this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This header is missing a few of the newer features from the specification.
Add these as well as a link to the spec. Also use the BIT() macros where
appropriate.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make sure that SW_RST_REQ and RST_REQ_MSK are cleared
before triggering hardware reset request.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The workaround of LPI one-way reset issue is broken by the series:
https://patchwork.ozlabs.org/project/uboot/list/?series=192398
This patch is to add DT node for GIC RD tables and create corresponding
reserved-memory node in kernel DT to fix it.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Configure DWC3’s cache type to ‘cacheable’ for better
performance. Actually related register definition and values are SoC
specific, which means this setting is only applicable to Layerscape SoC,
not generic for all platforms which have integrated DWC3 IP.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
The cpu_eth_init() is only used by the legacy ethernet driver framework.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Map all resource for R5 to operate properly.
The patch is done based on the commit 23f7b1a776 ("armv7R: K3: am654:
Enable MPU regions") which also map the whole 4GB at first and then change
mapping for DDR.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It was protected just for SPL_OS_BOOT but this function is only called when
SPL_ATF is enabled that's why change macro name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Value of shunt resistor for INA226s that monitor VCCINT and VCC_SOC power
rails are incorrect. This patch corrects those values.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
There is 2nd pca9548 mux on I2C1 bus that controls SFP0, SFP1, and QSFP1
ports. Channel 0 and 1 are connected to J287 connector for SFP0 & SFP1, and
channel 2 is connected to J288 connector for QSFP1.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add read/write memory utilities for 16 and 32 bits. Add these
api's for both little and big endian systems similar to arm
architecture.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not source xilinx board Kconfig by other boards. These configs should be
available only when Xilinx platforms are selected.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GPIO bank name for banks J and K are not correct when using the
'gpio' command from the console.
The driver derives the bank name from the device tree instance string by
using the instance value and adding 'A': gpio0@xxaddrxx is Bank A,
gpio1@yyaddryy is Bank B and so on.
On the PIC32, there is no Bank I so instances 8 and 9 need to be
incremented as a minimum change.
An alternative (less opaque) implementation would be to use a bank-name
property instead but this would require modifying the driver code too.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
GPIO state cannot be changed via the device tree (e.g. with gpio-hog) or
using the 'gpio' command from the console.
The root cause is a discrepancy between the driver and the device tree:
the driver code expects an absolute I/O address in the <reg> property,
while the device tree defines the address relative to a declaration in
the parent pinctrl node.
Changing the device tree to fix a driver issue would normally be wrong,
however:
- I have run the first version of U-Boot in which this driver appears
(v2016.03) and the same problem exists, so this is not a regression;
- There is no code that references a parent device tree node that might
suggest the intent of the author was to parse the DT as it exists now;
- The equivalent Linux PIC32 GPIO driver also uses absolute addresses
for the GPIO <reg> property. This change brings the U-Boot DT more
into line with Linux.
Additionally, the data sheet (Microchip ref. 60001361H) shows that the
register set to control a GPIO bank spans 0xE0 bytes, but the device
tree specified size is only 0x48 bytes.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
The PIC32MZ DA Starter Kit does not need the card detect workaround
because the SDCD signal line is connected properly. Disable the
workaround in this case.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
Add boolean input argument @no_map to helper function
fdtdec_add_reserved_memory() to add or not "no-map" property
for an added reserved memory node.
Property no-map is used by the Linux kernel to not not map memory
in its static memory mapping. It is needed for example for the|
consistency of system non-cached memory and to prevent speculative
accesses to some firewalled memory.
No functional change. A later change will update to OPTEE library to
add no-map property to OP-TEE reserved memory nodes.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present 64-bit sunxi boards use the Makefile to create a FIT, using
USE_SPL_FIT_GENERATOR. This is deprecated.
Update sunxi to use binman instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Linking a U-Boot larger than 1MB fails with PIE enabled:
u-boot/arch/arm/cpu/armv8/start.S:71:(.text+0x3c): relocation
truncated to fit: R_AARCH64_ADR_PREL_LO21 against symbol `__rel_dyn_end'
defined in .bss_start section in u-boot.
This extends the supported range by using adrp & add to load symbols
early while starting up.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
PIE requires a 4K aligned load address. If this is not met, trap
the startup sequence in a WFI loop rather than running into obscure
failures.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: André Przywara <andre.przywara@arm.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mention the requirement of 4K aligned load addresses in the
help section for the POSITION_INDEPENDENT option.
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Atmel PIT timer is not available for next products that
have another timer hardware block.
To be able to use the common at91 code, guard the code that uses PIT
by ifdefs.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We already have a function to retrieve the mac address from one EEPROM.
For boards with a second Ethernet interface, however, we would
require another EEPROM with a second unique MAC address.
Introduce at91_set_eth1addr which will look for a second EEPROM
and set the 'eth1addr' variable with the obtained MAC address.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add a missing memset to acpi_create_spcr().
The other acpi_create_xxxx() functions perform a memset on their
structures, acpi_create_spcr() does not and as a result the contents of
this table are partly uninitialized (and thus random after every reset).
Fixes: b288cd9600 ("x86: acpi: Generate SPCR table")
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix the tags format in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Currently, the calculation for the length of the DSDT table includes any
bytes that are added for alignment, but those bytes are not initialized.
This is because the DSDT length is calculated after a call to
acpi_inc_align(). Split this up into the following sequence:
* acpi_inc()
* Calculate DSDT length
* acpi_align()
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The term eMMC is used inconsistently within the FSP devicetree
bindings (e-mmc and emmc), especially for "emmc-host-max-speed"
documentation and code disagree.
Change all eMMC instances within the FSP bindings to consistently
use "emmc". The term "emmc" is already used a lot within U-Boot,
while "e-mmc" is only used in the FSP bindings.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct one typo in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
There are drivers to support built in USB controller and PHY-s now, so lets add the USB nodes to DTSI.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Since we have a driver for the reset controller, lets add the necessary node.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
There is already existing driver for SMEM so lets enable it for IPQ40xx as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Its common to use dt-bindings instead of hard-coding clocks or resets.
So lets use the imported Linux GCC bindings on IPQ40xx target.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The Toradex product is called apalis-imx8 consisting of SoM with
i.MX8QM and i.MX8QP SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The Toradex product is called colibri-imx8x consisting of SoM with
i.MX8QXP and i.MX8DX SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch adds support for iMX6UL/ULL/SL/SDL MMDC into the DDR calibration
code. The difference between MX6DQ and MX6UL/ULL/SL is that the later SoCs
have 2 SDQS registers, just like MX6SX, while the MX6DQ/MX6SDL has 8.
Fixes: 4f4c128c65 ("ARM: mx6: ddr: Add support for iMX6SX")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Latest datasheet revE has removed MIMX8ML7D/5D/7C/5C parts, so
update u-boot to remove decoding and support for those parts.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix SSCG_PLL_REFCLK_SEL_x, the offset starts from 0, not 16
Reported-by: Coverity 3448860
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Coverity reported dead code, however it is FRAC_PLL_REFCLK_SEL_MASK
was wrongly set.
Reported-by: Coverity 10045172
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
According to i.MX 7Dual Applications Processor Reference Manual, Rev. 1
The target interface CCM root index ranges [0,124], so the number
should be 125.
Reported-by: Coverity 18045
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
enable DTS support for keymile mpc83xx based boards.
get rid of compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Therefore done:
- add DTS for all mpc83xx based boards from keymile
mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
in board code, but not in linux DTS
- remove not used ethernet nodes
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Series-to: u-boot
Series-version: 3
Series-changes: 3
- rebase patchset to current mainline commit
c0192950df
- update defconfig files
Series-changes: 2
- add patch which fixes Codingstyle errors in drivers/qe
- add patch which converts the mpc83xx based boards from
keymile to DM_ETH
Cover-letter:
powerpc, mpc83xx: add DM_ETH support
This patch series adds DM ethernet support for mpc83xx based
keymile boards.
Travis build:
END
add DM support for parallel I/O ports on QUICC Engine Block
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Series-changes: 2
- remove RFC
- fixed Codingstyle errors, therefore new patch
powerpc, mpc83xx: fix codingstyle issues for qe_io.c
- moved DM part to drivers/pinctrl
Commit-notes:
Open questions / discussion:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This should be removed if all boards are converted to
DM/DTS.
- Unfortunately linux DTS does not use "pinctrl-"
properties, instead "pio-handle" properties.
Even worser old U-Boot code initializes all pins
defined in "const qe_iop_conf_t qe_iop_conf_tab[]"
table in board code. As linux does the same I decided
to also scan through all subnodes containing "pio-map"
property and initialize them too.
The proper solution would be to check for "pio-handle"
when a device is probed.
END
The following bugs are fixed:
* unaligned access in br_i32_decode()
* missing restore of global data pointer in UEFI selftest
* missing restore of global data pointer on RISC-V in UEfI subsystem
* efi_var_mem_notify_exit_boot_services() should not be __efi_runtime
-----BEGIN PGP SIGNATURE-----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=BNos
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc5
The following bugs are fixed:
* unaligned access in br_i32_decode()
* missing restore of global data pointer in UEFI selftest
* missing restore of global data pointer on RISC-V in UEfI subsystem
* efi_var_mem_notify_exit_boot_services() should not be __efi_runtime
The linker sometimes creates PT_LOAD segments with length (p_filesz) zero
as described in https://man7.org/linux/man-pages/man5/elf.5.html. This
leads to build failures. We should ignore empty segments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Hyperflash boot for J7200
- Update Main R5FSS lockstep mode
- R5F remoteproc support for J7200
- Minor env fixes
- Add SPI boot support for am335x-icev2
Add platform data and a device structure for the spi device
present on am335x-icev2. This requires moving all omap3_spi
platform data structures and symbols to an omap3_spi.h so that
the board file can access them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add a generic fs_loader node to the K3 J7200 R5 common board dts
file and use it as the chosen firmware-loader so that it can be
used for loading various firmwares from a boot media/filesystem
in R5 SPL on K3 J7200 EVM.
Signed-off-by: Suman Anna <s-anna@ti.com>
The J7200 SoCs have 2 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster is present within the MCU
domain (MCU_R5FSS0), and the other one is present within the MAIN
domain (MAIN_R5FSS0). Each of these can be configured at boot time
to be either run in a LockStep mode or in an Asymmetric Multi
Processing (AMP) fashion in Split-mode. These subsystems have 64 KB
each Tightly-Coupled Memory (TCM) internal memories for each core
split between two banks - ATCM and BTCM (further interleaved into
two banks). The TCMs of both Cores are combined in LockStep-mode
to provide a larger 128 KB of memory.
Add the DT node for the MAIN domain R5F cluster/subsystem, the two
R5F cores are added as child nodes to the main cluster/subsystem node.
The cluster is configured to run in Split-mode by default, with the
ATCMs enabled to allow the R5 cores to execute code from DDR with
boot-strapping code from ATCM. The inter-processor communication
between the main A72 cores and these processors is achieved through
shared memory and Mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
The J7200 SoCs have 2 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster is present within the MCU
domain (MCU_R5FSS0), and the other one is present within the MAIN
domain (MAIN_R5FSS0). Each of these can be configured at boot time
to be either run in a LockStep mode or in an Asymmetric Multi
Processing (AMP) fashion in Split-mode. These subsystems have 64 KB
each Tightly-Coupled Memory (TCM) internal memories for each core
split between two banks - ATCM and BTCM (further interleaved into
two banks). The TCMs of both Cores are combined in LockStep-mode
to provide a larger 128 KB of memory.
Add the DT node for the MCU domain R5F cluster/subsystem, the two
R5F cores are added as child nodes to the main cluster/subsystem node.
The cluster is configured to run in LockStep mode by default, with
the ATCMs enabled to allow the R5 cores to execute code from DDR with
boot-strapping code from ATCM. The inter-processor communication
between the main A72 cores and these processors is achieved through
shared memory and Mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
The A72 U-Boot code can load and boot a number of the available
R5FSS Cores on the J7200 SoC. Change the memory attributes for the
DDR regions used by the remote processors so that the cores can see
and execute the proper code.
The J7200 SoC has less number of remote processors compared to J721E,
so use less memory for the remote processors. So, a separate table
based on the current J721E table is added for J7200 SoCs, and selected
using the appropriate Kconfig CONFIG_TARGET_J7200_A72_EVM symbol.
Signed-off-by: Suman Anna <s-anna@ti.com>
Switch the MAIN R5FSS1 cluster to be configured for Split-mode as the
default so that two different applications can be run on each of the
R5F cores in performance mode. LockStep-mode would be available only
on SoCs efused with the appropriate bit, and Split-mode is the mode
that is available on all J721E SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
HBMC controller on TI K3 SoC provides MMIO access to HyperFlash similar
to legacy Parallel CFI NOR flashes. Therefore alias HyperFlash bootmode
to NOR boot to enable SPL to load next stage using NOR boot flow.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Function set_gd() is needed in the UEFI sub-system if the global data
pointer is stored in a register.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Include ast2500-evb.dtb for CONFIG_ASPEED_AST2500 instead of
for all aspeed targets.
ast2400 is based on ARM926EJ-S processor (ARMv5-architecture).
ast2500 is based on ARM1176JZS processor (ARMv6-architecture).
ast2600 is based on Cortex A7 processor (ARMv7-A architecture).
Each of the above SOC is using a different ARM CPU(s) with different ARM
architecture revision. It is not possible to support all 3 of these
families in a single binary. So there is no need to build ast2500-evb.dtb
for other SOC families.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Modify SPDX-License for furture patch warning
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
v2: modify title description aspeed:clock -> clock:aspeed
Use kernel include/dt-bindings/clock/aspeed-clock.h define
for clock driver.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Rename the ast2500-scu.h to aspeed-clock.h.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
PLL4Q is supplying both FDCAN and LTDC. In case HDMI is in use, the
50 MHz generated from PLL4Q cannot be divided well enough to produce
accurate clock for HDMI pixel clock. Adjust it to generate 74.25 MHz
instead. The PLL4P/PLL4R are generating 99 MHz instead of 100 MHz,
which is in tolerance for the SDMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Gerald Baeza <gerald.baeza@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
There is no dedicated pull resistor on the AV96 UART4 (console UART)
pin. In case there is no UART adapter installed on the AV96, the line
is floating and can trigger reception of garbage characters, which in
turn can abort U-Boot autoboot. Add default pull up to mitigate this
problem.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove the unnecessary inversion on the eth_env_set_enetaddr() result which
only make complex the code of setup_mac_address() and display an invalid
value in the associated pr_err.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Instead of querying SDM for FPGA configuration status through mailbox
messages, U-Boot now checks System Manager's FPGA Config status register
for FPGA configuration status before resetting bridge.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add g_dnl_get_board_bcd_device_number, the new BCD value is used by uuu to distinguish
if the SPL supports the SDPV.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Extend fastboot_set_reboot_flag arguments with reboot reason so that
it could handle different reboot cases in future.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
This function is not actually used in U-Boot. Drop it.
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Introduce USE_EARLY_BOARD_INIT option and select it by the actual users.
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enabled SDIO slot 0 (south bridge) for SD card on
Espressobin board.
Change-Id: I51a2debf9fba276b9c4a2bc6da91328d47f443e3
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/60945
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
[pali: Define cd-gpios and enable CONFIG_DM_REGULATOR_GPIO]
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
Change active-high to active-low and change DT property name from
reset-gpio to reset-gpios. This format of gpio reset is used by
pci-aardvark driver in Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
This commit fixes initialization of COMPHY on EspressoBin.
Commit 22f418935b ("phy: marvell: a3700: Use comphy_mux on Armada
37xx.") introduced usage of comphy_mux on Armada 37xx comphy driver.
The lanes are defined in comphy_a3700.c as described in functional
specification, that is:
lane 0 is SGMII1 or USB3
lane 1 is PCIe or SGMII0
lane 2 is SATA or USB3
But the DTS for EspressoBin configures PCIe on lane 0 and USB3 on
lane 1, which is wrong in the sense of the specification and doesn't
work with the comphy_mux code, which is 2 years now (the aardvark driver
causes synchronous abort in U-Boot).
It worked till the above mentioned commit, because the code for powering
up PCIe PHY doesn't work with lane number at all, and the code for
powering up USB3 PHY works differently only if USB3 is on lane 2, ie.
the check goes like:
if (lane == 2)
something
else
something else
so it does not differentiate between lanes 0 and 1.
In the future I shall post patches that remove the comphy_a3700 driver
and add comphy driver which uses calls to ATF, like Linux' driver does.
This will have the advantage of same DTS bindings as Linux', but till
this is done, we need this patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Pali Rohár <pali@kernel.org>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
Update the ringacc and udma dt nodes to use the latest RM resource types
similar to the ones used in k3-j721e dt nodes.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
ARC is selecting TIMER which depends on DM but DM is not selected and
doesn't need to be enabled. Fix it by selecting DM for ARC architecture.
Kconfig is showing this missing dependency by:
WARNING: unmet direct dependencies detected for TIMER
Depends on [n]: DM [=n]
Selected by [y]:
- ARC [=y] && <choice>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
arch_setup_bdinfo() only configures the deprecated bi_memstart &
bi_memsize values, which should not be needed any more. Lets remove
this file completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ovidiu Panait <ovidiu.panait@windriver.com>
With the planned removal of bi_memstart & bi_memsize, this patch now
moves the references to the better suiting gd->ram_base/ram_size
variables.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 86cf1c8285 ("configs: Migrate CONFIG_NR_DRAM_BANKS") &
commit 999a772d9f ("Kconfig: Migrate CONFIG_NR_DRAM_BANKS"),
CONFIG_NR_DRAM_BANKS is always defined with a value (4 is default).
It makes no sense to still carry code that is guarded with
"#ifndef CONFIG_NR_DRAM_BANKS" (and similar). This patch removes
all these unreferenced code paths.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel)
- Infrastructure changes to PCI uclass to support these SoC's (Suneel)
- Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel)
- Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
- Sipeed Maix support S-mode.
- Provide command sbi.
- Use fdtdec_get_addr_size_auto_parent to get fu540 cache base address.
- Fix a compiler error with CONFIG_SPL_SMP=n.
- Fix sifive ram driver 32 compiler warnings.
- Fix kendryte/pll.h redefine nop() warning.
We have a number of platforms that are a combination of a carrier board
and System-on-Module (SoM) that in turn allows for the board to have
different SoCs on it. In some cases, this is handled via board-specific
Kconfig options. In other cases we make use of
CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid
configurations as we will not in turn get options that in Kconfig are
selected by or depend on that setting.
To resolve this, make the SoC option a choice in Kconfig and make boards
depend on what they can support. This change opens us up for further
clean-ups in the cases where a single CONFIG_TARGET_xxx can support
different SoCs and today they do not, or do not cleanly do so.
Reported-by: Matt Porter <mporter@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Soeren Moch <smoch@web.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ian Ray <ian.ray@ge.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Cc: Simone CIANNI <simone.cianni@bticino.it>
Cc: Adam Ford <aford173@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Parthiban Nallathambi <parthiban@linumiz.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Niel Fourie <lusus@denx.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Silvio Fricke <open-source@softing.de>
Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch adds support for all OcteonTX2 96xx/95xx
boards from Marvell.
For 96xx boards, use octeontx_96xx_defconfig and
for 95xx boards, use octeontx_95xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
This patch adds support for all OcteonTX 81xx/83xx
boards from Marvell.
For 81xx boards, use octeontx_81xx_defconfig and
for 83xx boards, use octeontx_83xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Enable PCI memory regions in ranges property to be of multiple entry.
This helps to add support for SoC's like OcteonTX/TX2 where every
peripheral is on PCI bus.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Provide a command to display information about the SBI implementation.
The output might look like:
=> sbi
SBI 0.2
OpenSBI
Extensions:
sbi_set_timer
sbi_console_putchar
sbi_console_getchar
sbi_clear_ipi
sbi_send_ipi
sbi_remote_fence_i
sbi_remote_sfence_vma
sbi_remote_sfence_vma_asid
sbi_shutdown
SBI Base Functionality
Timer Extension
IPI Extension
RFENCE Extension
Hart State Management Extension
The command can be used to construct a unit test checking that the
communication with the SEE is working.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@openfive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
Building with CONFIG_SPL_SMP=n results in:
arch/riscv/lib/spl.c: In function ‘jump_to_image_no_args’:
arch/riscv/lib/spl.c:33:6:
error: unused variable ‘ret’ [-Werror=unused-variable]
33 | int ret;
| ^~~
Define the variable ret as __maybe_unused.
Fixes: 191636e448 ("riscv: Introduce SPL_SMP Kconfig option for U-Boot SPL")
Fixes: 8c59f2023c ("riscv: add SPL support")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
At present fdtdec_get_addr() is used to get L2 cache controller base
address. This only works for a fixed #address-cells and #size-cells.
Change to use fdtdec_get_addr_size_auto_parent() instead.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
Total Compute is based on ARM architecture and has
the following features enabled in u-boot:
- PL011 UART
- PL180 MMC
- NOR Flash
- FIT image with Signature
- AVB
Signed-off-by: Usama Arif <usama.arif@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
binman fixes for portage
various minor fixes
'bind' command improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl9BbZcRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZZiQf/UVsriftmxdDz3Lvbz7Jw6UCBXbeM3UN8
KgRxVll3kurZeu8bIcjAPY4YRrbWRqSXmZTXpZWgbyZzHLM4RnkamY3KF3DoxPjc
cbskd/fr4nPjSZVFrkzrvD+D5bhm+VrMtf861AkbAqqpG+Q1FmWHgApqOL1fXn3s
2VoMxRz8Cn9KkSDmxaCtJnLX77GVYYdfgii7RuNWGDqr3eBWrzflV38VbPHLplEg
VLqaLBe3G4zVwElA9Nc2hXpZB84KZEETHcBnmCzNkrSYTN2ofvSeZrWbtRztQFhz
yKur1y7jFsryRkMfxBzgldsKFRNnPT9vr+0qGtrztHjCmvhDkx1YMg==
=iDRJ
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-22aug20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
replace devfdt_get_addr_ptr() with dev_read_addr_ptr()
binman fixes for portage
various minor fixes
'bind' command improvements
The sections described in the sandbox linker script are inserted before
data section via "INSERT BEFORE .data;". Running readelf -S on sandbox
u-boot binary shows that the bss section is located after the data
section:
Section Headers:
[Nr] Name Type Address Offset
Size EntSize Flags Link Info Align
...
[25] .u_boot_list PROGBITS 000000000041d1c8 0021d1c8
000000000000dd90 0000000000000000 WA 0 0 8
[26] _u_boot_sandbox_g PROGBITS 000000000042af58 0022af58
00000000000000a0 0000000000000000 WA 0 0 8
[27] .data PROGBITS 000000000042b000 0022b000
000000000000f708 0000000000000000 WA 0 0 32
[28] .bss NOBITS 000000000043a720 0023a708
0000000000018930 0000000000000000 WA 0 0 32
This means that the __bss_start assignment in the linker script is bogus,
as the actual bss section start is located elsewhere. Remove this
assignment, as the __bss_start symbol is not used on sandbox anyway.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Usage of lists_bind_fdt() in bind command imposes to add
a compatible string for bind-test node.
Others impacts are:
- bind-test node is binded at sandbox start, so no need to bind it
in test_bind_unbind_with_node() test.
- As explained just above, after sandbox start, now a phy exist.
In test/dm/phy.c, it was verified that a third phy didn't exist,
now we must verified that a fourth phy doesn't exist.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sdmmc node is missing after the dts sync patch:
167efc2c7a arm64: dts: rk3399: Sync v5.7-rc1 from Linux
But we still need it for boot from SD card, so add it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Start to use ENV_VARS_UBOOT_RUNTIME_CONFIG to enable/disable updating
variables with run time information.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove chip_id function and integrate the firmware call in the
zynqmp_get_silicon_idcode_name function. The change avoids querying the
firmware twice and makes the code bit more clear.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removes duplicated definition of PAYLOAD_ARG_CNT and define it in the
firmware driver. Additionally fixes payload buffer declarations without
macro usage
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
s/xlnx,mio_bank/xlnx,mio-bank/g
DT binding is describing mio-bank not mio_bank that's why fix all DTSes and
also driver itself.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Remove adhoc dt binding for fixed-partition definition for i2c eeprom.
fixed-partition are using reg property instead of offset/size pair.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PM return payload size is defined as 4 bytes for Versal arquitecture
while the PM calls implemented both in the Versal clock driver and
ZynqMP firmware driver expects 5 bytes length.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Versal loadpdi command is used for loading secure & non-secure
pdi images.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
asm_sel is for switching between sata and pcie mode
on r64 there is GPIO90 connected to ASM1480 which
switches RX/TX pairs to PCIe/SATA connector
output-low means sata-controller is active
with 2020-10 now reg is also needed for the phy itself
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This patch adds PCIe node in dts for Mediatek MT7622 Soc.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
This patch adds pciesys support in dts for MediaTek MT7622 SoC.
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
This function is unused since commit 862274913f ("bus:
uniphier-system-bus: move hardware init from board files").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fill is code for programming the DDR_PHY_CMD_DESKEW_CONx registers,
which are optional, but can be used to fill in the byte lane delays.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement the 'getprisec' subcommand of 'bmode' command for i.MX7 by
reading out the SRC GPR10 bit 30. This bit is either set by the BootROM
if it switched to the secondary copy due to primary copy being corrupted
OR it can be overridden by the user.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add new 'getprisec' subcommand to 'bmode' command, which sets the return
value of the 'bmode' command to either 0 if the system booted from primary
copy or to 1 if the system booted from secondary copy. This can be used
e.g. in 'test' command to determine which copy of the system is running.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The i.MX6/i.MX7 is capable of booting a secondary "redundant" system
image in case the primary one is corrupted. The user can force this
boot mode as well by explicitly setting SRC GPR10 bit 30. This can be
potentially useful when upgrading the bootloader itself. Expose this
functionality to the user.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add the basic differentiation between i.MX6 and i.MX7 into the bmode
command, the mechanism really works almost the same on both platforms.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Make required updates to run on u-boot and strip test code.
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Add support for Xen para-virtualized serial driver. This
driver fully supports serial console for the virtual machine.
Please note that as the driver is initialized late, so no banner
nor memory size is visible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Port hypervisor related code from Mini-OS. This is referencing the code
of Mini-OS from [1] by Huang Shijie and Volodymyr Babchuk which is for
ARM64.
Update essential arch code to support required bit operations, memory
barriers etc.
Copyright for the bits ported belong to at least the following authors,
please see related files for details:
Copyright (c) 2002-2003, K A Fraser
Copyright (c) 2005, Grzegorz Milos, gm281@cam.ac.uk,Intel Research Cambridge
Copyright (c) 2014, Karim Allah Ahmed <karim.allah.ahmed@gmail.com>
[1] - https://github.com/zyzii/mini-os.git
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
[trini: Drop wmb() from musb-net/linux-compat.h now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce a minimal Xen guest board running as a virtual
machine under Xen Project's hypervisor [1], [2].
Part of the code is ported from Xen mini-os and also uses
work initially done by different authors from NXP: please see
relevant files for their copyrights.
[1] https://xenbits.xen.org
[2] https://wiki.xenproject.org/
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
The hardcoded platform variables such as DRAM base address are not
common to Aspeed SoCs AST24xx/AST25xx/AST26xx. This patch replaces
those hardcoded with macros defined in a newly added header, where
the basic SoC HW information are assigned accordingly.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Rename the ast2500-board.c to board_common.c and
place the renamed file under the ast2500 folder.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
The original lowlevel_init function of AST2500 is written
in C. However, the C runtime environment is not ready until
_main execution.
This patch adds the assembly version of the lowlevel_init
function. Additional initialization to DRAM configuration
and LPC reset source are also added.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
If an exception occurs, the relocated program counter and return address
are required for an analysis.
With this patch you get:
=> exception undefined
Unhandled exception: Illegal instruction
EPC: 0000000080595908 RA: 000000008059c0c6 TVAL: 000000008030c01e
EPC: 0000000080007908 RA: 000000008000e0c6 reloc adjusted
We can use the relocated addresses to find the involved functions in
u.boot.map:
.text.do_undefined
0x0000000080007908 0x8 cmd/built-in.o
.text.cmd_process
0x000000008000dfcc 0x11a common/built-in.o
0x000000008000dfcc cmd_process
If an exception occurs in an UEFI binary additionally the load addresses of
the UEFI binaries are needed. With this patch:
=> setenv efi_selftest exception
=> bootefi selftest
Unhandled exception: Illegal instruction
EPC: 000000008042e18a RA: 000000008042e18a TVAL: 000000008030c01e
EPC: 000000007fea018a RA: 000000007fea018a reloc adjusted
UEFI image [0x0000000000000000:0xffffffffffffffff] '/\selftest'
UEFI image [0x000000008042e000:0x000000008042e43f] pc=0x18a '/bug.efi'
The value pc=0x18a matches the position of the illegal instruction in
efi_selftest_miniapp_exception.efi (loaded as /bug.efi);
asm volatile (".word 0xffffffff\n");
00000180 93 85 C5 11 1C 64 22 85 82 97 FF FF FF FF 1C 64
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We should not initialize a variable if the value is overwritten before
being read.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
After
if (ret) return ret;
we know that ret is zero. Don't check it again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
All FU540 driver related options should be in the SoC level Kconfig.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
spl_soc_init() seems to be a better name, as all SPL functions
names start from the spl_ prefix.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
The generic SPL version of board_init_f() should give a call to
board specific codes to initialize board in the SPL phase.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
-----BEGIN PGP SIGNATURE-----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=J4aq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200813' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Use IS_ENABLED to prevent ifdef in board_key_check for STM32MP
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
Fix these dtc warnings:
Warning (reg_format)
Warning (avoid_default_addr_size)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
The STM32MP1 DHCOM has two ethernet interfaces, the on-SoM DWMAC and KS8851.
Set eth1addr for the KS8851 to a MAC address of the DWMAC incremented by 1.
The MAC of the DWMAC is set from on-SoM EEPROM already, but the MAC address
of KS8851 was left uninitialized, so fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch adds FMC2 External Bus Interface support on stm32mp157c.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in stm32prog command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in bsec driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the basic a72 basic dts for j7200. Following nodes were supported:
- UART
- MMC SD
- I2C
- TISCI communication
- LPDDR with 1600MTs configuration.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Detect if sysfw is already loaded by ROM and pass this information to
sysfw loader. Based on this information sysfw loader either loads the
sysfw image from boot media or just receives the boot notification
message form sysfw.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Starting J7200 SoC, ROM supports for loading sysfw directly from boot
image. ROM passes this information on number of images that are loaded
to bootloader at certain location. Add support for storing this
information before it gets corrupted.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
The J7200 SoC is a part of the K3 Multicore SoC architecture platform.
It is targeted for automotive gateway, vehicle compute systems,
Vehicle-to-Vehicle (V2V) and Vehicle-to-Everything (V2X) applications.
The SoC aims to meet the complex processing needs of modern embedded
products.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, two clusters of lockstep
capable dual Cortex-R5F MCUs and a Centralized Device Management and
Security Controller (DMSC).
* Configurable L3 Cache and IO-coherent architecture with high data
throughput capable distributed DMA architecture under NAVSS.
* Integrated Ethernet switch supporting up to a total of 4 external ports
in addition to legacy Ethernet switch of up to 2 ports.
* Upto 1 PCIe-GEN3 controller, 1 USB3.0 Dual-role device subsystems,
20 MCANs, 3 McASP, eMMC and SD, OSPI/HyperBus memory controller, I3C and
I2C, eCAP/eQEP, eHRPWM among other peripherals.
* One hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
management.
See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1
Add support for detection J7200 SoC
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
In main control mmr there is no partition 4 and partition 6 is available
only on J721e. Fix the same in ctrl_mmr_unlock function
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Add an api soc_is_j721e(), and use it to enable certain functionality
that is available only on j721e. This detection is needed when DT is not
available.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Starting J7200 SoC, ROM supports for loading sysfw directly from boot
image. In such cases, SPL need not load sysfw from boot media, but need
to receive boot notification message from sysfw. So separate out
remoteproc calls for system controller from sysfw loader and just
receive the boot notification if sysfw is already loaded.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
mmr_unlock api is common for all k3 devices. Move it to a common
location.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
If SPL_MULTI_DTB_FIT is not enabled, then CONFIG_SPL_OF_LIST is not defined
And in turn tispl.bin ends up not embedding any DTB.
Fixing it by using CONFIG_DEFAULT_DEVICE_TREE if SPL_OF_LIST is empty.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Guard all eeprom probe with TI_I2C_BOARD_DETECT to avoid reading eeprom
when eeprom is not available
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
U-boot only supports either USB host or device mode for a node at a
time in dts. To support both host and dfu bootmodes, set "peripheral"
as the default dr_mode but fixup property to "host" if host bootmode
is detected.
This needs to happen before the dwc3 generic layer binds the usb device
to a host or device driver. Therefore, add an fdtdec_setup_board()
implementation to fixup the dt based on the boot mode.
Also use the same fixup function to set the USB-PCIe Serdes mux to PCIe
in both the host and device cases. This is required for accessing the
interface at USB 2.0 speeds.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
In order to be able to use things like file system drivers early on in
SPL (before relocation) in a memory-constrained environment when DDR is
not yet available we cannot use the simple malloc scheme which does not
implement the freeing of previously allocated memory blocks. To address
this issue go ahead and enable the use of the full malloc by manually
initializing the required functionality inside board_init_f by creating
a full malloc pool inside the pre-relocation malloc pool.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The various CBASS interconnect nodes on K3 J721E SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
The various CBASS interconnect nodes on K3 AM65x SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
This commit completes the migrations for DM_ETH and DM_USB. The board
is now consistent with omap3_beagle and other remaining OMAP3 boards.
Cc: Tom Rini <trini@konsulko.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
When switching on or off the ARM caches some care must be taken to ensure
existing cache line allocations are not left in an inconsistent state.
An example of this is when cache lines are considered non-shared by
and L3 controller even though the lines are shared. To prevent these
and other issues all cache lines should be cleared before enabling
or disabling a coherent master's cache. ARM cores and many L3 controllers
provide a way to efficiently clean out all cache lines to allow for
this, unfortunately there is no such easy way to do this on current K3
MSMC based systems.
We could explicitly clean out every valid external address tracked by
MSMC (all of DRAM), or we could attempt to identify only the set of
addresses accessed by a given boot stage and flush only those
specifically. This patch attempts the latter. We start with cleaning the
SPL load address. More addresses can be added here later as they are
identified.
Note that we perform a flush operation for both the flush and invalidate
operations, this is not a typo. We do this to avoid the situation that
some ARM cores will promote an invalidate to a clean+invalidate, but only
emit the invalidation operation externally, leading to a loss of data.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Add DT entries for main domain watchdog0 and 1 instances on the J721e
well as RTI1-based watchdog on the AM65x. RTI0 does not work for this
purpose on the AM65x, so leave it out.
On AM65x, we mark the power-domain as shared because RTI firmware such
as https://github.com/siemens/k3-rti-wdt may request it as well in order
to prevent accidental shutdown of the watchdog.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add LED support for Cortina Access Presidio Engineering Board
Signed-off-by: Jway Lin <jway.lin@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CC: Simon Glass <sjg@chromium.org>
Factor out ppc-specific bdinfo setup from generic init sequence to
arch_setup_bdinfo in arch/powerpc/lib/bdinfo.c.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Factor out m68k-specific bdinfo setup to arch_setup_bdinfo in
arch/m68k/lib/bdinfo.c. Also, use if(IS_ENABLED()) instead of #ifdef where
possible.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Move all assignments to gd->bd->bi_mem{start,size} to generic code in
setup_bdinfo.
Xtensa architecture is special in this regard as it defines its own
handling of gd->bd->bi_mem{start,size} fields. In order to avoid defining
a weak SDRAM function, let arch_setup_bdinfo overwrite the generic flags.
For ARC architecture, remove ARCH_EARLY_INIT_R from Kconfig since it is
not needed anymore.
Also, use gd->ram_base to populate bi_memstart to avoid an ifdef.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Acked-by: Alexey Brodkin <abrokdin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
bi_sramstart and bi_sramsize are generic members of the bd_info structure,
so move the m68k/powerpc-specific prints to generic code. Also, print them
only if SRAM support is enabled via CONFIG_SYS_HAS_SRAM.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Update the MikroTik CRS305-1G-4S flash layout to support redundant UBI
partitions.
Additionally enable the UBI commands in crs305-1g-4s_defconfig.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS305-1G-4S Bit board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
The Bit board variant is added, which has a bigger Macronix flash.
Add basic U-Boot, UART and Winbond SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
We still have some platforms that only implements functionalities in
PSCI 0.1 (e.g. Allwinner ARMv7 SoCs).
Add a Kconfig option for exporting only PSCI 0.1. The code to export
PSCI 0.1 is still available and gets activated by this patch.
In addition, default ARCH_SUNXI U-Boot PSCI implementation to export
PSCI 0.1, to fix poweroff/reboot regression on Allwinner multi-core
ARMv7 SoCs.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
SPL_CLEAR_BSS is called regardless of build type if
CONFIG_SPL_EARLY_BSS is defined. Add a guard for CONFIG_SPL_BUILD
to fix.
Signed-off-by: Brian Moyer <bdm310@gmail.com>
This patch adds a feature for block device cloning similar to dd
command, this should be useful for boot-strapping a device where
usb gadget or networking is not available. For instance one can
clone a factory image into a blank emmc from an external sd card.
Signed-off-by: John Chau <john@harmon.hk>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
This header file should not be included in other header files. Remove it
from each one and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
PRCI module within SiFive SoC's has register with which we can
reset the sub-systems within the SoC. The resets to DDR and ethernet
sub systems within FU540-C000 SoC are active low, and are hold low
by default on power-up. Currently these are directly asserted within
prci driver via register read/write.
With the DM based reset driver support here, we bind the reset
driver with clock (prci) driver and assert the reset signals of
both sub-system's appropriately.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
The resets to DDR and ethernet sub-system are connected to
PRCI device reset control register, these reset signals
are active low and are held low at power-up. Add these reset
producer and consumer details needed by the reset driver.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This patch selects DM_SPI & DM_I2C for MIPS Octeon. DM_GPIO, DM_SERIAL
and DM_ETH are already selected.
Additionally the selections are now alphabetically sorted.
Signed-off-by: Stefan Roese <sr@denx.de>
Instead of hang()ing the system and thus disallowing any automated
recovery possibility from a HAB authentication failure, panic() .
The panic() function can be configured to hang() the system after
printing an error message, however the default is to reset the
system instead.
This allows redundant boot to work correctly. In case the primary
or secondary image cannot be authenticated, the system reboots and
bootrom can try to start the other one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based
on imx6ULL SoC from NXP and provision for expansion board. This
commit adds support only for SBC with NAND.
CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 45C
Reset cause: WDOG
Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND
Board: MYiR MYS-6ULX 6ULL Single Board Computer
DRAM: 256 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: FEC0
Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
- ApolloLake: add u64 parameters support for FSP2 bindings
- ApolloLake: add missing parameters to support full configuration of
the latest FSP MR6 release
- Append appropriate suffixes in various assembly codes
Assembler is not happy:
arch/x86/cpu/call32.S: Assembler messages:
arch/x86/cpu/call32.S:36: Warning: no instruction mnemonic suffix given and no register operands; using default for `retf'
Fix this by adding appropriate suffixes to the assembler commands.
Fixes: 6f92ed8f1a ("x86: Add a way to call 32-bit code from 64-bit mode")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Assembler is not happy:
arch/x86/cpu/sipi_vector.S: Assembler messages:
arch/x86/cpu/sipi_vector.S:134: Warning: no instruction mnemonic suffix given and no register operands; using default for `cmp'
arch/x86/cpu/sipi_vector.S:139: Warning: no instruction mnemonic suffix given and no register operands; using default for `bts'
arch/x86/cpu/sipi_vector.S:157: Warning: no instruction mnemonic suffix given and no register operands; using default for `cmp'
Fix this by adding appropriate suffixes to the assembler commands.
Fixes: 45b5a37836 ("x86: Add multi-processor init")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add missing parameters to support full configuration of the latest FSP
MR6 release.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add FSP_UINT64 read support as preparation for FSP-M and FSP-S parameter
update.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix some typos in arch/x86/include/asm/irq.h.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add simple DT and clock bindings to r2dplus DT to permit U-Boot
to bind the SCIF driver via DT probing instead of hard-coded
config options.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The gd->malloc_base must be set before the C runtime if the MALLOC_F_LEN
is non-zero, otherwise we hit assertion in dlmalloc.c initf_malloc(). So
set it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Kconfig symbol CONFIG_STACK_SIZE is used both by ARM and Microblaze
with the same meaning. Move it to menu 'General setup' so that we can use
it for all architectures.
Use the value of CONFIG_STACK_SIZE instead of a hard coded 16 MiB value for
reserving memory in the UEFI sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Configuration variables should have the same meaning independent of the
architecture. x86 and ARM both use CONFIG_STACK_SIZE:
* x86: U-Boot's runtime stack size during reboot
* ARM: max stack size that can be used by U-Boot
Rename the x86 configuration variable to CONFIG_STACK_SIZE_REBOOT
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Refactor to allow any arch to create SPI-flash images
New button uclass
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8g33sRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaeEgf/QhmJjd6lEE3ABncRa3texyqq7j9eu+9P
2JMCahrIzps83LLOkzNSGs1+m1hRuTcdnYNV8FxdmkAjDTYwV5RHOfwtpAr2nkH2
HBbJRA2qMPleqT8wcymouhaCIRTTCGfUkFgZ+OowwSlHnQ4d2oGU/59Z+AkbpfX0
3svA1Mlr5rUTZ3qTvdsepuZckuYOTGYZ5jgjbgr+G8F4iW4Ov+OkBxqDz9zFCveF
md5CHKP1SV+bq67Q9uqUEwatLzYpy1p24j1Qe4G08U1+XCi6r+95VEc7TWxggboj
eV/5d/sZbGESAtJiJ4TmqpGVcOLzBLI0FOunky0JNFwdcyRS/6KcCg==
=Xjil
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28jul20' of git://git.denx.de/u-boot-dm
Use binman instead of one of the Rockchip build scripts
Refactor to allow any arch to create SPI-flash images
New button uclass
- fix SPL boot issue due to early dbgmcu_init() call
- fix SPL boot issue due to dcache memory region configuration
- add support of CONFIG_ENV_IS_IN_MMC
- add specific SD/eMMC partition for U-Boot enviromnent
- enable env in SPL
- use "env info -q" to remove log during boot
- remove env location override for dh_stm32mp1
- update management of misc_read
- check result of find_mmc_device in stm32prog
- use regulator_set_enable_if_allowed for disabling vdd supply in usbphyc
- enable CMD_ADTIMG flag to handle Android images
- device tree alignment with Linux Kernel v5.8-rc1
- remove hnp-srp-disable for usbotg on dk1
- add reset support to uart nodes on stm32mp15x
- use correct weak function name spl_board_prepare_for_linux
- use cd-gpios for ST and DHSOM boards
- add seeed studio odyssey-stm32mp157c board support
- move ethernet PHY into SoM DT
- add DHSOM based DRC02 board support
Use device tree and UCLASS_SYSCON driver to get
Generic Interrupt Controller (GIC) lpi address and
maximum GIC redistributors count.
Also update Kconfig to select REGMAP and SYSCON when
GIC_V3_ITS is enabled.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use device tree and UCLASS_IRQ driver to get following
Generic Interrupt Controller (GIC) details,
-GIC Distributor interface (GICD) base address and
-GIC Redistributors (GICR) base address.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch bcmns3.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add both DRAM banks memory information and
the corresponding MMU page table mappings.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add API to save boot parameters passed from BL31
Use assembly implementation of save_boot_params instead of c function.
Because generally ATF does not set up SP_EL2 on exiting.
Thus, usage of a C function immediately after exiting with no stack
setup done by ATF explicitly, may cause SP_EL2 to be not sane,
which in turn causes a crash if this boot was not lucky to get
an SP_EL2 in valid range. Replace C implementation with assembly one
which does not use stack this early, and let u-boot to set up its stack
later.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Broadcom Northstar 3 SoC.
NS3 is a octo-core 64-bit ARMv8 Cortex-A72 processors
targeting a broad range of networking applications.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- SPL not supported yet --> no spl-dir in arch/arm/cpu/armv7/s5p4418/.
Appropriate line in Makefile removed.
- cpu.c: '#include <cpu_func.h>' added.
- arch/arm/cpu/armv7/s5p4418/u-boot.lds removed, is not required
anylonger.
- "obj-$(CONFIG_ARCH_NEXELL) += s5p-common/" added to
arch/arm/cpu/armv7/Makefile since s5p-common/pwm.c is used instead
of drivers/pwm/pwm-nexell.c.
- s5p4418.dtsi: '#include "../../../include/generated/autoconf.h"'
removed, is not necessary, error at out-of-tree building.
'#ifdef CONFIG_CPU_NXP4330'-blocks (2x) removed. Some minor changes
regarding mmc. 'u-boot,dm-pre-reloc' added to dp0 because of added
DM_VIDEO support.
- board/s5p4418/ renamed to board/friendlyarm/
- All s5p4418-boards except nanopi2 removed because there is no
possibility to test the other boards.
- Kconfig: Changes to have a structure like mach-bcm283x (RaspberryPi),
e.g. "config ..." entries moved from/to other Kconfig.
- "CONFIG_" removed from several s5p4418/nanopi2 specific defines
because the appropriate values do not need to be configurable.
- nanopi2/board.c: All getenv(), getenv_ulong(), setenv() and saveenv()
renamed to env_get(), env_get_ulong(), env_set() and env_save(),
respectively. MACH_TYPE_S5P4418 is not defined anymore, therefore
appropriate code removed (not necessary for DT-kernels).
- nanopi2/onewire.c: All crc8() renamed to crc8_ow() because crc8() is
already defined in lib/crc8.c (with different parameters).
- dts: "nexell,s5pxx18-i2c" used instead of "i2c-gpio", i2c0 and
i2c1 added. gmac-, ehci- and dwc2otg-entries removed because the
appropriate functionality is not supported yet. New mmc-property
"mmcboost" added.
s5p4418-pinctrl.dtsi: gmac-entries removed, mmc- and i2c-entries
added.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- Since drivers/pwm/pwm-nexell.c is an adapted version of
s5p-common/pwm.c an appropriately changed version of s5p-common/pwm.c
is used instead. Therefore arch/arm/mach-s5pc1xx/include/mach/pwm.h
copied to arch/arm/mach-nexell/include/mach and s5p-common/Makefile
changed appropriately.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- SPL not supported yet --> no spl-directory in arch/arm/mach-nexell.
Appropriate line in Makefile removed.
- clock.c: 'section(".data")' added to declaration of clk_periphs[] and
core_hz.
- Kconfig: Changes to have a structure like in mach-bcm283x/Kconfig,
e.g. "config ..." entries moved from other Kconfig.
- timer.c: 'section(".data")' added to declaration of timestamp and
lastdec.
- arch/arm/mach-nexell/serial.c removed because this is for the UARTs
of the S5P6818 SoC which is not supported yet. S5P4418 UARTs are
different, here the (existing) PL011-code is used.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
The LPAE versions of DCACHE_WRITEBACK and DCACHE_WRITETHROUGH are currently
defined as no-allocate for both reads and writes, which deviates from the
non-LPAE definition, and mostly defeats the purpose of enabling the caches
in the first place.
So align LPAE with !LPAE, and enable allocate-on-read for both. And while
at it, add some clarification about the meaning of the chosen values.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
This introduces initial support for the popular Qualcomm
IPQ40x8 and IPQ40x9 WiSoC series.
IPQ40xx series have 4x Cortex A7 ARM-v7A cores.
Supported are: IPQ4018, IPQ4019, IPQ4028 and IPQ4029.
IPQ40x8 and IPQ40x9 use the same cores, but differ in
addressable RAM size (1GB for IPQ40x9 and 256MB for IPQ40x8)
and supported peripherals (IPQ40x8 lacks RGMII, LCD controller
and EMMC/SDHCI controllers).
IQP4028/IPQ4029 models differ from IPQ4018/IPQ4019 only
by their rated temperatures rates with IPQ402X models being
rated for wider temperature ranges.
Initially this supports:
* Simple clock driver (Only for UART1 now, will be extended)
* Pinctrl driver (Supports UARTX and GPIO now, will be extended)
* GPIOs already supported by msm_gpio driver with updates
* UARTs already supported by serial_msm driver with updates
Further peripherals will come in later patches.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Adds two buttons on sandbox so button framework may be tested.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Since commit 9ba84329dc ("sandbox, test: add test for GPIO_HOG
function"), the gpio_a 0,1,2 and 3 are used by hog in test.dts.
But 2 leds 'sandbox:red' and 'sandbox:green' are using gpio_a 0
and 1. As hog always request his gpios, the led command on both
led is broken:
=> led sandbox:red
LED 'sandbox:red' not found (err=-16)
The gpio is already requested by hog, so it can't be enabled
for led 'sandbox:red'.
This commit change the gpio used by hog to 10, 11, 12 and 13,
so the led command could be used again with 'sandbox:red' and
'sandbox:green'.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This board does not have microcode but at present that is not supported
by Kconfig nor the binman image layout. Fix both of these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This causes conflicts on chromebook_link64. Move it to after U-Boot where
there should be plenty of space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that all board use binman instead of this script, drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this board uses a custom script to produce the .its file.
Update it to use binman instead. Binman can create all the images that
are needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
On mediatek various files that need to be created by binman. It does not
make sense to enumerate these in the Makefile. They are described in the
configuration (devicetree) for each board and we can simply run binman
(always) to generate them.
This avoid sprinkling the Makefile with arch-specific code.
Also update the binman definition so that idbloader.img is only needed
when SPL is actually being used.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Quite a few boards using this SoC family don't use binman, yet
CONFIG_BINMAN is enabled for all of them. But the option should only be
enabled if we expect binman to produce an image. Calling binman when the
device tree is missing, etc. will cause failer.
Add a condition so that CONFIG_BINMAN is only enabled as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When binman is in use, most of the targets built by the Makefile are
inputs to binman. We then need a final rule to run binman to produce the
final outputs.
Rename the variable to indicate this, and add a new 'inputs' target.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present only the ARMv7 tegra SoCs actually use binman to create an
image. Change the config to reflect this, since otherwise running binman
will produce an error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple binman config and enable CONFIG_HAS_ROM so that U-Boot
produces a ROM for jerry.
Change the binman image definition to support multiple images, since it
may be used to build both u-boot-rockchip.bin and u-boot.rom
Signed-off-by: Simon Glass <sjg@chromium.org>
Most x86 boards build a u-boot.rom which is programmed into SPI flash. But
this is not unique to x86. For example some rockchip boards can also boot
from SPI flash.
Also, at least on x86, binary blobs are sadly quite common. It is not
possible to build a functional image without them, and U-Boot needs to
know this at build time.
Introduce a new CONFIG_HAS_ROM option which selects whether u-boot.rom is
built and a new CONFIG_ROM_NEEDS_BLOBS option to indicate whether binary
blobs are also needed. If they are not needed, it is safe to build the ROM
always. Otherwise we still require the BUILD_ROM environment variable.
For now this affects only x86, but future patches will enable this for
rockchip too.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add DT for DH DRC02 unit, which is a universal controller device.
The system has two ethernet ports, two CANs, RS485 and RS232, USB,
capacitive buttons and an OLED display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The PHY and the VIO regulator is populated on the SoM, move it
into the SoM DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This commit adds device tree files supporting
SBC from Seeed Studio based on STM32MP157C.
This works with generic stm32mp1 config.
Right now only booting from SD card is supported.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Since commit f13ff88b61 ("gpio: stm32: add ops set_dir_flags")
the gpio flags are supported by stm32 pinctrl driver.
The cd-gpios is correctly handle in U-Boot and the patch on the
device tree can be removed.
This reverts commit 792919241b.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Since commit f13ff88b61 ("gpio: stm32: add ops set_dir_flags")
the gpio flags are supported by stm32 pinctrl driver.
The cd-gpios is correctly handle in U-Boot and the patch on the
device tree can be removed.
This reverts commit 3c2e2a1a79.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Replace the function spl_board_prepare_for_boot_linux by the correct
name of the weak function spl_board_prepare_for_linux defined in spl.h.
This patch avoids warning with W=1 option:
u-boot/arch/arm/mach-stm32mp/spl.c:150:6:
warning: no previous prototype for ‘spl_board_prepare_for_boot_linux’
[-Wmissing-prototypes]
Fixes: dc7e5f190d ("arm: stm32mp: activate data cache on DDR in SPL")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
STM32 serial IP can be reset via reset controller.
Add the support of reset to uart nodes on stm32mp15-u-boot.dtsi,
the ad-dons file for U-Boot.
This patch fix issues when previous UART configuration, for example
done in TF-A or ROM code, is not handled in U-Boot stm32 serial driver
init.
This reset property won't be not added in Linux kernel device tree
as this reset is not used in Linux STM32 serial driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove hnp-srp-disable for usbotg node because this feature is only needed
for usbotg in HOST mode (in drivers/usb/host/dwc2.c)
and this feature is not activated in stm32mp15 U-Boot
(stm32mp15_basic_defconfig and stm32mp15_trusted_defconfig);
only the device mode is activated and OTG is not supported in DWC2 driver.
This patch reduces the difference between U-Boot and Linux kernel
device-tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
DT alignment with Linux kernel v5.8-rc1 for the STM32MP15x soc
device tree files and the STMicroelectronics boards device tree files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Alignment with pins name used in Linux kernel v5.8.
It is a preleminary step for device tree alignment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Check result of find_mmc_device() before calling mmc_init().
This patch avoid a data abort when the command try to acces
to sd/mmc device deactivated in device tree.
Fixes: aff4c5dd82 ("stm32mp: stm32prog: add MMC device")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Save the environment at the end of the U-Boot partition, the GPT
partition named "ssbl" in SD card or eMMC and avoid requirements
on the "bootfs" file system generated via specific raw tools
(like wic and genimage).
With the previous configuration of the U-Boot environment saved in ext4
file, U-Boot need to create/modify the file uenv.txt in the ext4 file
system; so this EXT4 file system need to be generated without some
functionality, like metadata_csum and dir_index, because they are not
supported by U-Boot.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Since commit d877f8fd0f ("arm: provide a function for boards init
code to modify MMU virtual-physical map") the parameter of
mmu_set_region_dcache_behaviour need to be MMU_SECTION_SIZE
aligned.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As the dbgmcu_init use the function bsec_dbgswenable which is based
on the DM and DT, its call can't be done before the spl is initialized
(driver model, DT and malloc) in board_init_f::spl_early_init().
This function call is moved later in spl_board_init().
Fixes: bd3f60d29c ("arm: stm32mp: protect DBGMCU_IDC access with BSEC")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
Checkpatch reports the following issue:
ERROR: space prohibited before that ',' (ctx:WxW)
#936: FILE: arch/arm/mach-imx/imx8m/soc.c:936:
+ 0, 0 , 0, 0, 0, 0, &res);
Remove the unneeded space.
^
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
According to i.MX 7Solo Applications Processor Reference Manual,
2.1.3 Cortex-M4 Memory Map, M4 can address only 1536MB of DDRC
(Start Address: 0x8000_0000; End Address: 0xDFFF_FFFF).
Correct DDRC size to 0x60000000.
Fixes: c0f037f6("mach-imx: bootaux: elf firmware support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Add the PCIe EP node for ls1046a.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a rev2 requires 4KB space for type0 and 4KB
space for type1 iATU window. Increase configuration
size to 8KB to have sufficient space for type0
and type1 window.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The workaround has been implemented in PBI phase, so remove
the duplicated implementation from U-Boot.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The sdhc_adapter of global data has not been used, and we
do not have to use it as global data even we may need it
in the future.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This enables SYS_I2C_MXC to fix a bug that
failed to boot from sd card with
image u-boot-with-spl-pbl.bin
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There are two issues:
(1) The spin table doesn't convert the endianness of the jump address.
Although there is code for it, the result isn't used at all (x0).
(2) If something goes wrong, the function returns. But that doesn't
make sense at all.
Use the actual converted jump address as destination to fix. If
there is an error, jump to a trap loop. And rearrange the code exception
level switching code to make it smaller and clearer.
This reduces the size of the spin table code section from 696 bytes to
424 bytes. If CONFIG_ARMV8_SWITCH_TO_EL1 the code size reduced from 696
bytes to 632 bytes.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
On ARM64, a 64kb region is reserved for the runtime services code.
Unfortunately, this code overlaps with the spin table code, which also
needs to be reserved. Thus now that the code is relocatable, allocate a
new page from EFI, copy the spin table code into it, update any pointers
to the old region and the start the secondary CPUs.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a new variable secondary_boot_code_start, which holds a pointer to
the start of the spin table code. This will help to relocate the code
section. While at it, move the size variable from the end to the
beginning so there is a common section for the variables. Remove any
other symbols.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that the spin table is in a separate module, this is no longer
necessary. Drop it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This function is not used outside the module. Make it static.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no need to cast around. Assign the address to the local
variable and use it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Only the PowerPC architecture needs this function. Remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix the alignment so it will match the comments. The spin table has to
be 8 byte aligned, so ".align 3" is enough.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Don't use LDR to load a pointer to a function. This will generate a
literal which cannot be relocated. Use ADR which is PC-relative and
therefore can easily be relocated.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move it out of lowlevel.S into spintable.S. On layerscape, the secondary
CPUs are brought up in main u-boot. This will make it possible to only
compile the spin table code for the main u-boot and omit it in SPL.
This saves about 720 bytes in the SPL.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The generic armv8 code already has support to bring up the secondary
cores. Thus, don't hardcode the jump in the layerscape lowlevel_init to
the spin table code; instead just return early and let the common armv8
code handle the jump. This way we can actually use the CPU_RELEASE_ADDR
feature.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased, Removed kontron_sl28.h change as file does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Make the print of the starting address a debug output and pretty print
the info about online cores.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Spin tables are broken with bootefi. This is because - in contrast to
the booti call chain - there is no call to smp_kick_all_cpus(). Due to
this missing call the secondary CPUs are never released from their "wait
for interrupt state", see secondary_boot_func() in lowlevel.S.
Originally, this "wait for interrupt" is there to make sure, the spin
table is cleared before the secondary cores read it for the first time.
But the boot flow for the layerscape architecture is different from
that. The CPUs are release from their BootROM _after_ U-Boot's
spin-table is cleared, see fsl_layerscape_wake_seconday_cores() in mp.c.
Thus, there is no need to wait for this interrupt and no need for
kicking all cores on cpu_release. An atomic 64bit write to the
spin-table and a "sev" is sufficient.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_FSL_LAYERSCAPE is available in kconfig. There is no need to
define it per board; the ls1028a_common.h is really board dependent and
only fits to the NXP eval boards. Instead select CONFIG_FSL_LAYERSCAPE
when ARCH_LS1028A is selected.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a sandbox SOC driver, and some tests for the SOC uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
These functions should not modify the device. Convert them to const so
that callers don't need to cast if they have a const udevice *.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also
known as the RZ/G2M.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch imports the device tree and required bindings to permit
the device tree to build for the R8Z774A1 (RZ/G2M).
Signed-off-by: Adam Ford <aford173@gmail.com>
In order to build boards based on the R8A774A1, there needs to
be a config option from which to enable other drivers and/or flags
for this SoC.
Signed-off-by: Adam Ford <aford173@gmail.com>
- Fix SiFive HiFive Unleashed board booting failure problem.
- Enable SiFive fu540 PWM driver.
- Support SiFive fu540: SPI boot.
- Update OpenSBI used for RISC-V CI testing.
- Revert "riscv: Allow use of reset drivers".
- Revert "Revert "riscv: sifive: fu540: Add gpio-restart support"".
- sysreset: syscon:
- Don't assume default value for offset and mask property.
- Support value property.
- qemu: Add syscon reboot and poweroff support.
- Fix SIFIVE debug serial dependency.
- Fix linking error when building u-boot-spl with no SMP support.
- AE350 use fdtdec_get_addr_size_auto_noparent to parse smc reg.
- Make memory node available to SPL in hifive-unleashed-a00-u-boot.dtsi
- SiFive fu540 avoid using hardcoded ram base and size.
Make memory node available to SPL in prepration to updates to SiFive
DDR RAM driver to read memory information from DT.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Switch off SMP support when building u-boot-spl would cause linking error as follow:
undefined reference to 'secondary hart relocate' and 'smp_call_function'.
Add macro to wrap up proper code region that needs SMP configuration on.
Signed-off by: Leo Liang <ycliang@andestech.com>
Cc: rick@andestech.com
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This reverts commit 958a3f464c.
A more appropriate change below is already in mainline.
Commit fd31e4fd18 ("riscv: Do not build reset.c if SYSRESET is on")
Revert this patch, so that U-Boot can be built successfully for
SiFive Fu540 board.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Add booting from SPI for SiFive Unleashed board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Commit 40686c394e ("riscv: Clean up IPI initialization code")
caused U-Boot failed to boot on SiFive HiFive Unleashed board.
The codes inside arch_cpu_init_dm() may call U-Boot timer APIs
before the call to riscv_init_ipi(). At that time the timer register
base (e.g.: the SiFive CLINT device in this case) is unknown yet.
It might be the name riscv_init_ipi() that misleads people to only
consider it is related to IPI, but in fact the timer capability is
provided by the same SiFive CLINT device that provides the IPI.
Timer capability is needed for both UP and SMP.
Considering that the original refactor does have benefits, that it
makes the IPI code more similar to U-Boot initialization idioms.
It also removes some quite ugly macros. Let's do the minimal revert
instead of a complete revert, plus a fixes to arch_cpu_init_dm() to
consider the SPL case.
Fixes: 40686c394e ("riscv: Clean up IPI initialization code")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Leo Liang <ycliang@andestech.com>
- New rk3326 board: Hardkernel Odroid Go2;
- Update board config and dts for RockPI 4/N8/N10;
- Update led boot on support for roc-rk3399-pc;
- Enable SPI Flash suppor for rk3328 rock64 board;
- Update rockchip pcie phy to use generic framework;
Add u-boot,spl-boot-order for ROCKPi N10, so-that it can able
to boot from eMMC and SDMMC in order.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support to enable PCIe for RockPI N10.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support to enable HDMI out for
N10 and N8 combinations SBCs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa dalang carrier board has 2x USB 2.0 and 1x USB 3.0
ports.
This patch adds support to enable all these USB ports for
N10 and N8 combinations SBCs.
Note that the USB 3.0 port on RockPI N8 combination works
as USB 2.0 OTG since it is driven from RK3288.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3288 and rk3288w have a usb host0 ohci controller.
Although rk3288 ohci doesn't actually work on hardware, but
rk3288w ohci can work well.
So add usb host0 ohci node in rk3288 dtsi and the quirk in
ohci platform driver will disable ohci on rk3288.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This sync has changes required to use HDMI CEC pin in U-Boot.
Sync dts from linux v5.8-rc5 commit:
"ARM: dts: rockchip: define the two possible rk3288 CEC pins"
(sha1: 838980dd04e994bf81cf104fa01ae60802146b39)
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
reset cause is a generic functionality based on the soc
cru registers in rockchip. This can be used for printing
the cause of reset in cpuinfo or some other place where
reset cause is needed.
Other than cpuinfo, reset cause can also be using during
bootcount for checking the specific reset cause and glow
the led based on the reset cause.
So, let's separate the reset cause code from cpuinfo, and
add a check to build it for rk3399, rk3288 since these two
soc are supporting reset cause as of now.
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
reset reason can be used several stages of U-Boot bootloader
like SPL, U-Boot proper based on the requirements.
Clearing the status register end of get_reset_cause will end
up showing the wrong reset cause when it read the second time.
For example, if board resets, SPL reads the reset status as
RST whereas U-Boot proper reads the status as POR.
However, based on the latest testing clearing reset status
won't be required for determine the last reset cause or
following resets.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add weak led_setup() so that board which has an uncommon
led setup code that can make use of custom implementation.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The new rk3288 revision rk3288w has some changes with respect
to legacy rk3288 like hclk_vio in cru and usb host0 ohci.
Linux clock driver already handle this via rockchip,rk3288w-cru
compatible.
USB ohci host can enable via dts for rk3288w based boards.
So, add fdt board setup code to update cru compatible with
rk3288w-cru compatible if the SOC revision is RK3288W.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoC's has a new revision chip for rk3288 SoCs.
RK3288 has a new revision chip called RK3288W which is similar
but different hclk_vio clock and fixed OHCI host.
Add common Rockchip SoC detection helper to support this rk3288w
detection.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.
So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.
- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
GPIO pin change compared to 4B, 4C
So move common nodes, properties into dtsi file and include
on respective variant dts files.
Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently 2.5 GB is calculated as DRAM size for a 1 GB RK322x board
if CONFIG_SPL_OPTEE is set. This is troublesome when booting a
linux kernel since this size will be injected in FDT of the kernel.
gd->bd->bi_dram[0].start (which is basically CONFIG_SYS_SDRAM_BASE)
must not be taken into consideration for calculation of second bank
size, since this offset is already included in calculation of "top".
After applying this patch 992 MB (1024 MB - 32 MB reserved for
optee-os) is correctly calculated and has also been verified on
2 GB boards.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The empty function define should not be in the header file, or else the
build will error with function multi definition after CONFIG_RAM_ROCKCHIP_DEBUG
is disabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI support for the RK3328
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(fix checkpatch error for code ident)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Get the devicetree from mainline Linux and include it for U-Boot uses.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3326 is just a trimmed down px30 from a software perspective,
so the mainline rk3326 dtsi also ist just a tiny addition.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a sandbox SOC driver, and some tests for the SOC uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
These functions should not modify the device. Convert them to const so
that callers don't need to cast if they have a const udevice *.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a description of how this module works and also some missing function
comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To enable support for the 'mtrr' command, add a way to perform MTRR
operations on selected CPUs.
This works by setting up a little 'operation' structure and sending it
around the CPUs for action.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
When the boot CPU MTRRs are updated, perform the same update on all other
CPUs so they are kept in sync.
This avoids kernel warnings about mismatched MTRRs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
SMP should be set up in U-Boot where possible, not SPL. Disable it in SPL.
For 64-bit U-Boot we should find a way to allow SMP operations in U-Boot,
but this is somewhat more complicated. For now that is disabled too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Update the mtrr command to use mp_run_on_cpus() to obtain its information.
Since the selected CPU is the boot CPU this does not change the result,
but it sets the stage for supporting other CPUs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is convenient to iterate through the CPUs performing work on each one
and processing the result. Add a few iterator functions which handle this.
These can be used by any client code. It can call mp_run_on_cpus() on
each CPU that is returned, handling them one at a time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With the new MP features the CPUs are no-longer parked when the OS is run.
Fix this by calling a special function to park them, just before the OS is
started.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a way to run a function on a selection of CPUs. This supports either
a single CPU, all CPUs, just the main CPU or just the 'APs', in Intel
terminology.
It works by writing into a mailbox and then waiting for the CPUs to notice
it, take action and indicate they are done.
When SMP is not yet enabled, this just calls the function on the main CPU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Set this flag so we can track when it is safe to use CPUs other than the
main one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the APs (non-boot CPUs) are inited once and then parked ready
for the OS to use them. However in some cases we want to send new requests
through, such as to change MTRRs and keep them consistent across CPUs.
Change the last state of the flight plan to go into a wait loop, accepting
instructions from the main CPU.
Drop cpu_map since it is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Drop some #ifdefs that are not needed or can be converted to compile-time
checks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is misnamed since it does not actually init the BSP. Also
it is convenient to adjust it to return a little more information.
Rename and update the function, to allow it to return the BSP CPU device
and number, as well as the total number of CPUs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present each CPU is given a number when it starts itself up. While this
saves a tiny amount of time by doing the device-tree read in parallel, it
is confusing that the numbering happens on the fly.
Move this code into mp_init() and do it at the start.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This does not need to be global across all functions in this file. Pass a
parameter instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These parameters are named differently from elsewhere in this file. Switch
them to avoid confusion.
Also add comments to this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The functions used by the flight plan are declared in the header file but
are not used in any other file.
Move the flight plan steps down to just above where it is used so that we
can make these function static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the 'flight plan' for CPUs is passed into mp_init. But it is
always the same. Move it into the mp_init file so everything is in one
place. Also drop the SMI function since it does nothing. If we implement
SMIs, more refactoring will be needed anyway.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update this code to use livetree calls instead of flat-tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.
Supported devices:
- UART
- reset
- CFI parallel NOR flash
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the code to copy itself from bootrom location to a
different location (TEXT_BASE) to the Octeon platform. Its used in
this case to copy the complete U-Boot image into L2 cache, which
greatly improves the bootup time - especially in regard to the
very long and complex DDR4 init code.
The Kconfig symbol CONFIG_MIPS_MACH_EARLY_INIT is enabled with this
patch for Octeon.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds very basic support for the Octeon III SoCs. Only
CFI parallel NOR flash and UART is supported for now.
Please note that the basic Octeon port does not include the DDR3/4
initialization yet. This will be added in some follow-up patches
later. To still use U-Boot on with this port, the L2 cache (4MiB on
Octeon III CN73xx) is used as RAM. This way, U-Boot can boot to the
prompt on such boards.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the optional call to mips_mach_early_init() to start.S
at a very early stage. Its disabled per default. It can be used for
very early machine / platform specific init code. Its called very
early and at this stage the PC is allowed to differ from the linking
address (CONFIG_TEXT_BASE) as no absolute jump has been performed until
this call.
It will be used by thje Octeon platform.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Sync asm/mipsregs.h with Linux 5.7. Also replace the custom
symbols EBASE_CPUNUM and EBASE_WG with the according symbols
from Linux.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Sync asm/addrspace.h with Linux 5.7
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Sync asm/asm.h with Linux 5.7.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
This macro only served as a wrapper for CKSEG1ADDR() with an
exception for CONFIG_TB0229. CONFIG_TB0229 doesn't exist, thus
use CKSEG1ADDR() directly.
This also prepares for an upcoming asm header sync with Linux.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Add an own Kconfig symbol for the initial disabling of caches
invoked from generic start code.
Also add an own Kconfig symbols for the initialization of caches
invoked from generic start code.
Until now both code paths could only be disabled with
CONFIG_SKIP_LOWLEVEL_INIT. But this is not flexible enough for
RAM boot scenarios like EJTAG or SPL payload or for machines
which don't require cache initialization or which want to
provide their own cache implementation.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Logically this code belongs to cache_init.S.
If a complex SoC needs to replace the generic cache init,
mips_cache_disable() can now be called from custom start.S files.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
change_k0_cca() is called multiple times. Move the code for
changing to KSEG1 to a macro to avoid code duplication.
Also fix missing change to KSEG1 when changing to CONF_CM_CACHABLE_COW.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Since commit 703ec9ddf9 ("MIPS: Stop building position independent code")
the relocation code was completely reworked and removed from start.S.
Remove some left-overs of the old code.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
This patch adds __weak to invalidate_dcache_range() in lib/cache.c. This
makes it possible to overwrite this function by a platforms specific
version, which will be done for Octeon.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds __weak to flush_cache() in lib/cache.c. This makes it
possible to overwrite this function by a platforms specific version,
like done with the Octeon base port.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the usage of CONFIG_MIPS_L2_CACHE without
CONFIG_MIPS_CM, which is what is needed for the newly added Octeon
platform.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the R_MIPS_NONE define from 0 to a magic value. This
makes it possible to better detect any forbidden pre-relocation usage
of BSS variables, as they are often zero'ed and then relocation is
stopped too early.
Additionally the error message is improved to also print the faulting
address. This helps finding the root-cause for this breakage by
comparing this address with the values in System.map.
This patch helps a lot when working on pre-relocation code, like the
Octeon DDR init code, where such variables have hit me multiple times
now.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
This patch opts-out the compilation of get_tbclk() if
CONFIG_SYS_MIPS_TIMER_FREQ is not defined. This is used on the Octeon
platform, where the weak get_tbclk() function is overwritten by its
platform specific one.
Signed-off-by: Stefan Roese <sr@denx.de>
Some code was not converted by coccinelle, somehow.
I manually fixed up the remaining, and comments, README docs.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[trini: Add arch/arm/mach-davinci/include/mach/sdmmc_defs.h and
include/fdt_support.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
- New timer API to allow delays with a 32-bit microsecond timer
- Add dynamic ACPI structs (DSDT/SSDT) generations to the DM core
- x86: Enable ACPI table generation by default
- x86: Enable the copy framebuffer on Coral
- x86: A few fixes to FSP2 with ApolloLake
- x86: Drop setup_pcat_compatibility()
- x86: Primary-to-Sideband Bus minor fixes
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXxCxWw8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76bPyACcDZ8gD9jf1P/Zh+7kqrGdIWwURF8AnAiEtNnu
FhE/WQQj4mAEWE4F2bFE
=7ceG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.10
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
This should ideally be used by all x86 boards in U-Boot. Enable it by
default. If some boards don't use it, the cost is small.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function sounds like something that is called when U-Boot is about to
jump to Linux. In fact it is an init function.
Rename it to reduce confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Currently U-Boot implements version 2 but reports version 4. Correct it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
This function does not exist anymore. Drop it from the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The comment here applies only to FSP1, so update it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
At present this information is used to locate and parse the tables but is
not stored. Store it so that we can display it to the user, e.g. with the
'bdinfo' command.
Note that now the GD_FLG_SKIP_LL_INIT flag is set in get_coreboot_info(),
so it is always set when booting from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Update this code to calculate the address to use, rather than hard-coding
it. Obtain the requested stack size from the FSP.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If there is MRC information we should run FSP-M with a different
boot_mode flag since it is supposed to do a 'fast path' through the
memory init. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Writing tables is currently pretty opaque. Add a bit of debugging to the
process so we can see what tables are written and where they start/end in
memory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The FSP-S changes the ITSS priorities. The code that tries to save it
before running FSP-S and restore it afterwards does not work as U-Boot
relocates in between the save and restore. This means that the driver
data saved before relocation is lost and the new driver just sees zeroes.
Fix this by allocating space in the relocated memory for the ITSS data.
Save it there and access it from the driver after relocation.
This fixes interrupt handling on coral.
Also drop the log_msg_ret() in irq_first_device_type() since this function
can be called speculatively in places where we are not sure if there is
an interrupt controller of that type. The resulting log errors are
confusing when there is no error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
This binding currently has a flags cell but it is not used. Make use of it
to create ACPI tables for interrupts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
This confuses Linux's PCI probing so needs to be hidden when booting
Linux. Add a remove() method to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Tested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Add support for this new method in the driver and in the fsp-s setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Tested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Use the new binman memory-mapping function to access the VBT, to simplify
the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Generation of this table can fail, so update the function to return an
error code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
This is in the device tree now, so drop the unnecessary field here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we can query the offset of a pinctrl register within the p2sb.
For ACPI we need to get the actual address of the register. Add a function
to handle this and rename the old one to more accurately reflect its
purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
