Update the 'boot_net' script to load the fdt with the kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This macro currently supports only one parameter. Based on Linux iopoll,
let's extend read_poll_timeout common API to allow multiple variable
parameters.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
This driver supports NXP C45 TJA11XX PHYs, but there're also other NXP
TJA11XX PHYs. Let's rename functions in this driver to be c45 variant
specific, so further drivers can be introduced adding support for NXP
TJA11XX PHYs.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Since we envision using overlays for display interfaces, the video=
settings within vidargs are obsolete. Remove these settings from the
U-Boot.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
All the other NAND-based boards have tdxargs specified for setting
manual kernel command-line arguments.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The COUNTER_FREQUENCY is missed in 8ulp configs, it will cause SPL
and u-boot not set the cntfrq_el0. For u-boot, this is ok, because
ATF has set it. But for SPL, it will lead delay and get_timer
not working.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because the Beacon imx8mn board uses device tree
for MMC/SD and Ethernet, there is no need to have some of the
config options. It's handled by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Because the Beacon imx8mm board uses device tree
for MMC/SD and Ethernet, there is no need to have some of the
config options. It's handled by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add a driver for the Gateworks System Controller used on Gateworks boards
which provides a boot watchdog, power control, temperature monitor,
and voltage ADCs.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
In cpu_to_be32_array() and be32_to_cpu_array() we should not compare an int
counter to a size_t parameter. Correct the type of the counter. This
exists in upstream as b4c80629c5c9 ("include/linux/byteorder/generic.h:
fix index variables").
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
We need to know where the typedef of 'ofnode' comes from.
Fixes: c86a4de8df ("mtd: Add flash_node in struct mtd_info")
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, add_mtd_partitions_of() can be used only if dev field of
mtd_info struct is populated. It's the case, for example, for a spi nor
flash, which has a DT compatible "jedec,spi-nor" and an associated
device. mtd->dev is populated in spi_nor_scan().
But in case of a raw nand node, mtd_info's dev field can't be populated
as flash node has no compatible, so no associated device.
add_mtd_partitions_of() can't be used to parse "partitions" subnode.
To remove this constraint, add an ofnode field in mtd_info struct
which reference the DT flash node. This new field is populated by
nand_scan_tail(). This new field will be used by add_mtd_partitions_of()
to parse the flash node for "partitions" defined in DT.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Farhan Ali <farhan.ali@broadcom.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Prior to introduction of modifications in rsassa_pss functions
related to padding verification, doing a pass to update
const-correctness in targeted functions to comply with
coding-rules and avoid const-cast
Signed-off-by: SESA644425 <gioja.hermann@non.se.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This annotates malloc and friends so that valgrind can track the heap. To
do this, we need to follow a few rules:
* Call VALGRIND_MALLOCLIKE_BLOCK whenever we malloc something
* Call VALGRIND_FREELIKE_BLOCK whenever we free something (generally after
we have done our bookkeeping)
* Call VALGRIND_RESIZEINPLACE_BLOCK whenever we change the size of an
allocation. We don't record the original request size of a block, and
neither does valgrind. For this reason, we pretend that the old size of
the allocation was for 0 bytes. This marks the whole allocaton as
undefined, so in order to mark all bits correctly, we must make the whole
new allocation defined with VALGRIND_MAKE_MEM_DEFINED. This may cause us
to miss some invalid reads, but there is no way to detect these without
recording the original size of the allocation.
In addition to the above, dlmalloc itself tends to make a lot of accesses
which we know are safe, but which would be unsafe outside of dlmalloc. For
this reason, we provide a suppression file which ignores errors ocurring in
dlmalloc.c
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Valgrind uses magic code sequences to define an ABI that the client may use
to request behavior from the host. In particular, this may be used to
inform valgrind about custom allocators, such as the one used in U-Boot.
This adds headers defining these sequences to U-Boot. It also adds a config
option to disable emission of these sequences entirely, in the (likely)
event that the user does not wish to use valgrind. Note that this option is
called NVALGRIND upstream, but was renamed (and inverted) to
CONFIG_VALGRIND. Aside from this and the conversion of a few instances of
VALGRIND_DO_CLIENT_REQUEST_EXPR to STMT, these headers are unmodified.
These headers were copied from valgrind 3.16.1-4 as distributed in Arch
Linux. They are licensed with the bzip2 1.16 license. This appears to be a
BSD license with some clauses from Zlib.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation:
* Describe how enable DM_SERIAL for a board
UEFI
* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
-----BEGIN PGP SIGNATURE-----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=SxkC
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc1
Documentation:
* Describe how enable DM_SERIAL for a board
UEFI
* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
Currently we require PHY interface mode to be known when
finding/creating the PHY - the functions
* phy_connect_phy_id()
* phy_device_create()
* create_phy_by_mask()
* search_for_existing_phy()
* get_phy_device_by_mask()
* phy_find_by_mask()
all require the interface parameter, but the only thing done with it is
that it is assigned to phydev->interface.
This makes it impossible to find a PHY device without overwriting the
set mode.
Since the interface mode is not used during .probe() and should be used
at first in .config(), drop the interface parameter from these
functions. Make the default value of phydev->interface (in
phy_device_create()) to be PHY_INTERFACE_MODE_NA. Move the interface
parameter to phy_connect_dev(), where it should be.
Change all occurrences treewide. In occurrences where we don't call
phy_connect_dev() for some reason (they only configure the PHY without
connecting it to an ethernet controller), set
phydev->interface = value from phy_find_by_mask call.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Use phydev->is_c45 instead of is_10g_interface(phydev->interface) to
determine whether clause 45 protocol should be used.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Move PHY_INTERFACE_MODE_NA to the beginning of the enum definition to
make it have zero value. This makes it possible (although not
encouraged) to test for invalid/nonexistent interface mode with !val
instead of val == PHY_INTERFACE_MODE_NA.
The comment near the definition says "Must be last", because when the
constant was introduced in commit 5f184715ec ("Create PHY Lib for
U-Boot"), it was used as the maximum value when interating over the
constants. But this is no longer true - we use PHY_INTERFACE_MODE_MAX
for that now, and so we can move it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Rename constant PHY_INTERFACE_MODE_COUNT to PHY_INTERFACE_MODE_MAX to
make it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add wrappers dm_mdio_read(), dm_mdio_write() and dm_mdio_reset() for
DM MDIO's .read(), .write() and .reset() operations.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_get_phy_node() and dev_get_phy_node() and use it in
net/mdio-uclass.c function dm_eth_connect_phy_handle(). Also add
corresponding UT test.
This is useful because other part's of U-Boot may want to get PHY ofnode
without connecting a PHY.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With dm-tag feature, any U-Boot subsystem is allowed to associate
arbitrary number of data with a particular udevice. This can been
see as expanding "struct udevice" without modifying the definition.
As a first user, UEFI subsystem makes use of tags to associate
an efi_disk object with a block device.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for the upstream gpio-line-names property already described
in the common GPIO binding document[1]. The ability to search for a line
name allows boards to lift the implementation of common GPIO behaviours
away from specific line indexes on a GPIO controller.
[1] 3c35bfee83/dtschema/schemas/gpio/gpio.yaml (L17)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Based on current usage, migrate a number of DP-DDR related options to
Kconfig.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform has CONFIG_ETH_DESIGNWARE set already, which is the
correct value for the driver in question. Remove this incorrect line.
Signed-off-by: Tom Rini <trini@konsulko.com>
As no platforms override this value, set it for all mpc83xx platforms.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move these two options to the arch Kconfig file.
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
This symbol is only possibly useful on some mvebu platforms, so move the
symbol there and select it for the only current user.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a little tricky since SoCFPGA has code to determine this as
runtime. Introduce a guard variable for platforms to select if they
have a static value to use. Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONS_SCIF0
CONFIG_CONS_SCIF1
CONFIG_CONS_SCIF2
CONFIG_CONS_SCIF4
CONFIG_CONS_SCIFA0
Signed-off-by: Tom Rini <trini@konsulko.com>
These values are only used in one file, reference them more directly.
Cc: Kamil Lulko <kamil.lulko@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This code is only used on the corvus platform, so migrate the LED on/off
code to this platform and remove it from the CONFIG namespace. In
theory, this should likely be moved to the modern GPIO LED driver as a
further cleanup.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
A number of CONFIG options are used on these platforms as part of the
default environment. Set some of these more directly and in other
cases, just reference them directly.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CM_INIT
CONFIG_CM_REMAP
CONFIG_CM_SPD_DETECT
CONFIG_CM_MULTIPLE_SSRAM
CONFIG_CM_TCRAM
We make the first three of these options be always enabled, as that
matches usage. We select the last two based on how they were defined in
armcoremodule.h. This also allows us to remove some unused code in
board/armltd/integrator/lowlevel_init.S
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is only enabled for CI_UDC and !TEGRA20, so implement it as
such in Kconfig directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
This converts the following to Kconfig:
CONFIG_BOARD_SIZE_LIMIT
To do this, introduce CONFIG_HAS_BOARD_SIZE_LIMIT.
Signed-off-by: Tom Rini <trini@konsulko.com>
For platform which can boot on different device, this allows
to override interface, device and partition from board code
Signed-off-by: He Yong <hyyoxhk@163.com>
This file uses struct driver, so declare it at the top in case the
header-inclusion order is not as expected.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is normally defined in stdint.h but is not used in U-Boot. When
libraries (such as Chromium OS vboot) are built against U-Boot they may
expect this value to be available. Add it to avoid build errors in this
case.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the header file defines this function in SPL but the file may
not actually be built. This causes a build error if the option is enabled.
Fix the condition in the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use Sphinx style comments to describe functions.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Up till now the CONFIG_POWER_TPS65217 has been defined in several header
files for am335x SoC.
This patch renames it to CONFIG_PMIC_TPS65217, which better reflects the
role of this IC circuit.
Moreover, new CONFIG_PMIC_TPS65217 has been introduced in Kconfig
to be used with boards, which both support DM_PMIC and DM_I2C.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Migrate all other platforms as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
=HOoS
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
While creating a phy device using phy_device_create(), we need to
provide a valid phyaddr instead of 0 causing phy address being
registered as 0 with mdio bus and shows mdio phy list as below
ZynqMP> mdio list
eth0:
0 - TI DP83867 <--> ethernet@ff0b0000
eth1:
0 - TI DP83867 <--> ethernet@ff0c0000
Also PHY soft reset is being requested on 0 instead of valid
address causing "PHY reset timed out" error.
So add phyaddr argument to phy_connect_phy_id() and to its prototype
to create phy device with valid phyaddress.
Fixes: a744a284e3 ("net: phy: Add support for ethernet-phy-id with gpio reset")
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Link: https://lore.kernel.org/r/fe35fddb9faa5af577ffdfabaec6879c935a30f8.1648562755.git.michal.simek@xilinx.com
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Introduce ECC Functionality for full memory space as implemented in the
DDRSS. The following is done to accomplish this:
* Introduce a memory region "ss" to allow dt to provide DDRSS region,
which is not the same as "ctl" which is the controller region.
* Introduce a "ti,ecc-enable" flag which allows a memorycontroller
instance to enable ecc.
* Introduce functionality to properly program the DDRSS registers to
enable ECC for the full DDR memory space if enabled with above flag.
* Expose a k3_ddrss_ddr_fdt_fixup call to allow fixup of fdt blob to
account from DDR memory that must be reserved for ECC operation.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- Rearrange defconfig option order
- Add CONFIG_SAVE_PREV_BL_* options
- Doc updates:
- remove wrong SBOOT memory corruption note, because
memory is changed during u-boot bringup process,
not by SBOOT
- put payload on ramdisk place in abl boot image
creation step
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Platforms can overwrite the weak definition of spl_mmc_boot_mode() to
determine where to load U-Boot proper from.
For most of them this is a trivial decision based on Kconfig variables,
but it might be desirable the probe the actual device to answer this
question.
Pass the pointer to the mmc struct to that function, so implementations
can make use of that.
Compile-tested for all users changed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ley Foon Tan <ley.foon.tan@inte.com> (for SoCFPGA)
Acked-by: Lokesh Vutla <lokeshvutla@ti.com> (for OMAP and K3)
Reviewed-by: Simon Glass <sjg@chromium.org>
Most Allwinner sunxi SoCs have separate boot ROMs in non-secure and
secure mode. The "non-secure" or "normal" boot ROM (NBROM) uses the
existing sunxi_egon image type. The secure boot ROM (SBROM) uses a
completely different image type, known as TOC0.
A TOC0 image is composed of a header and two or more items. One item
is the firmware binary. The others form a chain linking the firmware
signature to the root-of-trust public key (ROTPK), which has its hash
burned in the SoC's eFuses. Signatures are made using RSA-2048 + SHA256.
The pseudo-ASN.1 structure is manually assembled; this is done to work
around bugs/quirks in the boot ROM, which vary between SoCs. This TOC0
implementation has been verified to work with the A50, A64, H5, H6,
and H616 SBROMs, and it may work with other SoCs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- strip unneeded config options
- add FIT image support
- add framebuffer node, u-boot logo and video console
- increase LMB_MAX_REGIONS, to store all linux dtb reserved memory regions
- add linux kernel image header
Uart driver causes hang, when u-boot is used in android boot image instead
of linux. Temporary disable console driver, until investigated and fixed.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
When u-boot is used as a chain-loaded bootloader (replacing OS kernel),
previous bootloader leaves data in RAM, that can be reused.
For example, on recent arm linux system, when chainloading u-boot,
there are initramfs and fdt in RAM prepared for OS booting. Initramfs
may be modified to store u-boot's payload, thus providing the ability to
use chainloaded u-boot to boot OS without any storage support.
Two config options added:
- SAVE_PREV_BL_INITRAMFS_START_ADDR
saves initramfs start address to 'prevbl_initrd_start_addr' environment
variable
- SAVE_PREV_BL_FDT_ADDR
saves fdt address to 'prevbl_fdt_addr' environment variable
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
We already support the NVMe commands and PCIe backend in the QEMU target,
so let's make it easy for anyone to consume them and enable NVMe distro
boot along the way!
With this patch, I can put an NVMe backed disk image into my QEMU VM and
have it automatically load a UEFI target blob.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Some serial drivers can be vastly more efficient when printing multiple
characters at once. Non-DM serial has had a puts option for these sorts
of drivers; implement it for DM serial as well.
Because we have to add carriage returns, we can't just pass the whole
string directly to the serial driver. Instead, we print up to the
newline, then print a carriage return, and then continue on. This is
less efficient, but it is better than printing each character
individually. It also avoids having to allocate memory just to add a few
characters.
Drivers may perform short writes (such as filling a FIFO) and return the
number of characters written in len. We loop over them in the same way
that _serial_putc loops over putc.
This results in around sizeof(void *) growth for all boards with
DM_SERIAL. The full implementation takes around 140 bytes.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If a debugger is not attached to U-Boot, semihosting calls will raise a
synchronous abort exception. Try to catch this and disable semihosting
so we can e.g. use another uart if one is available. In the immediate
case, we return an error, since it is not always possible to check for
semihosting beforehand (debug uart, user-initiated load command, etc.)
We handle all possible semihosting instructions, which is probably
overkill. However, we do need to keep track of what instruction set
we're using so that we don't suppress an actual error.
A future enhancement could try to determine semihosting capability by
inspecting the processor state. There's an example of this at [1] for
RISC-V. The equivalent for ARM would inspect the monitor modei
enable/select bits of the DSCR. However, as the article notes, an
exception handler is still helpful in order to catch disconnected
debuggers.
[1] https://tomverbeure.github.io/2021/12/30/Semihosting-on-RISCV.html#avoiding-hangs-when-a-debugger-is-not-connected
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
These functions are intended to support detecting semihosting and
falling back gracefully to alternative implementations. The test starts
by making semihosting call. SYS_ERRNO is chosen because it should not
mutate any state. If this semihosting call results in an exception
(rather than being caught by the debugger), then the exception handler
should call disable_semihosting() and resume execution after the call.
Ideally, this would just be part of semihosting by default, and not a
separate config. However, to reduce space ARM SPL doesn't include
exception vectors by default. This means we can't detect if a
semihosting call failed unless we enable them. To avoid forcing them to
be enabled, we use a separate config option. It might also be possible
to try and detect whether a debugger has enabled (by reading HDE from
DSCR), but I wasn't able to figure out a way to do this from all ELs.
This patch just introduces the generic code to handle detection. The
next patch will implement it for arm64 (but not arm32).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] 5b70c1f679/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
This adds a serial driver which uses semihosting calls to read and write
to the host's console. For convenience, if CONFIG_DM_SERIAL is enabled,
we will instantiate a serial driver. This allows users to enable this
driver (which has no physical device) without modifying their device
trees or board files. We also implement a non-DM driver for SPL, or for
much faster output in U-Boot proper.
There are three ways to print to the console:
Method Baud
================== =====
smh_putc in a loop 170
smh_puts 1600
smh_write with :tt 20000
================== =====
These speeds were measured using a 175 character message with a J-Link
adapter. For reference, U-Boot typically prints around 2700 characters
during boot on this board. There are two major factors affecting the
speed of these functions. First, each breakpoint incurs a delay. Second,
each debugger memory transaction incurs a delay. smh_putc has a
breakpoint and memory transaction for every character. smh_puts has one
breakpoint, but still has to use a transaction for every character. This
is because we don't know the length up front, so OpenOCD has to check if
each character is nul. smh_write has only one breakpoint and one memory
transfer.
DM serial drivers can only implement a putc interface, so we are stuck
with the slowest API. Non-DM drivers can implement puts, which is vastly
more efficient. When the driver starts up, we try to open :tt. Since
this is an extension, this may fail. If it does, we fall back to
smh_puts. We don't check :semihosting-features, since there are
nonconforming implementations (OpenOCD) which don't implement it (but
*do* implement :tt).
Some semihosting implementations (QEMU) don't handle READC properly. To
work around this, we try to use open/read (much like for stdin) if
possible.
There is no non-blocking I/O available, so we don't implement pending.
This will cause __serial_tstc to always return true. If
CONFIG_SERIAL_RX_BUFFER is enabled, _serial_tstc will try and read
characters forever. To avoid this, we depend on this config being
disabled.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds three wrappers around the semihosting commands for reading and
writing to the host console. We use the more standard getc/putc/puts
names instead of readc/writec/write0 for familiarity.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This command's functionality is now completely implemented by the
standard fs load command. Convert the vexpress64 boot command (which is
the only user) and remove the implementation.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds a filesystem which is backed by the host's filesystem. It is
modeled off of sandboxfs, which has very similar aims. Semihosting
doesn't support listing directories (except with SYS_SYSTEM), so neither
do we. it's possible to optimize a bit for the common case of reading a
whole file by omitting a call to smh_seek, but this is left as a future
optimization.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
In order to add filesystem support, we will need to be able to seek and
write files. Add the appropriate helper functions.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
There's no point in using string constants for smh_open if we are just
going to have to parse them. Instead, use numeric modes. The user needs
to be a bit careful with these, since they are much closer semantically
to string modes used by fopen(3) than the numeric modes used with
open(2).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This exports semihosting functions for use in other files. The header is
in include/ and not arm/include/asm because I anticipate that RISC-V may
want to add their own implementation at some point.
smh_len_fd has been renamed to smh_flen to more closely match the
semihosting spec.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The ARMv8-R64 architecture introduces optional VMSA (paging based MMU)
support in the EL1/0 translation regime, which makes that part mostly
compatible to ARMv8-A.
Add a new board variant to describe the "BASE-R64" FVP model, which
inherits a lot from the existing v8-A FVP support. One major difference
is that the memory map in "inverted": DRAM starts at 0x0, MMIO is at
2GB [1].
* Create new TARGET_VEXPRESS64_BASER_FVP target, sharing most of the
exising configuration.
* Implement inverted memory map in vexpress_aemv8.h
* Create vexpress_aemv8r defconfig
* Provide an MMU memory map for the BASER_FVP
* Update vexpress64 documentation
At the moment the boot-wrapper is the only supported secure firmware. As
there is no official DT for the board yet, we rely on it being supplied
by the boot-wrapper into U-Boot, so use OF_HAS_PRIOR_STAGE, and go with
a dummy DT for now.
[1] https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[Andre: rebase and add Linux kernel header]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add MAINTAINERS entry for Peter]
In preparation for the ARMv8-R64 FVP support, which has DRAM mapped at
0x0, generalise the page table generation, by using symbolic names for
the address ranges instead of fixed numbers.
We already define the base of the DRAM and MMIO regions, so just use
those symbols in the page table description. Rename V2M_BASE to the more
speaking V2M_DRAM_BASE on the way.
On the VExpress memory map, the address space right after 4GB is of no
particular interest to software, as the whole of DRAM is mapped at 32GB
instead. The first 2 GB alias to the lower 2GB of DRAM mapped below 4GB,
so we skip this part and map some more of the high DRAM, should anyone
need it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far the FVP model just supports booting through semihosting, so by
loading files from the host the model is running on. This allows for
quick booting of new kernels (or replacing DTBs), but prevents more
featureful boots like using UEFI.
Enable the distro_boot feature, and provide a list of possible boot
sources that U-Boot should check:
- For backwards compatibility we start with semihosting, which gets its
commands migrated from CONFIG_BOOTCOMMAND into the distro_boot
infrastructure. This is also slightly tweaked to fail graceful in case
the required files could not be found.
- Next we try to use a user provided script, that could be easily
placed into memory using the model command line.
- Since we gained virtio support with the enablement of OF_CONTROL,
let's check virtio block devices next. This is where UEFI boot can
be easily used, for instance by providing a distro installer .iso
file through virtio-blk.
- Networking is now provided by virtio as well, so enable the default
PXE and DHCP boot flows, mostly because we can.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The definition of the standard environment variables (kernel_addr_r and
friends) has been improved lately for the FVP model, but the Juno board
is still using some custom scheme.
Since we need to extend this to a third board soon, let's unify the
definition:
- Define the Juno addresses in the same generic way we do for the FVP
model, and move the actual variable setting out of the board #ifdef's.
- Add the missing addresses for a PXE file and a boot script.
- Cleanup some stale comments on the way.
As the FVP model doesn't have support for distro_boot quite yet, add
a dummy definition for now, to be replaced with the real thing later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE
Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NORFLASH_PS32BIT
Note that we also attempt to correct the behavior of the code here,
which had been testing for "NORFLASH_PS32BIT" which would never be set,
instead check for the now set "CONFIG_NORFLASH_PS32BIT", which results
in some behavior change.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_USE_NANDFLASH and CONFIG_SYS_USE_MMC serve the
same purpose as CONFIG_SD_BOOT / CONFIG_NAND_BOOT so migrate to using
these switches instead as they're already in Kconfig.
Cc: Stelian Pop <stelian@popies.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of M5373EVB we always had NANDFLASH_SIZE=16, so just use it
directly. In the case of M5329EVB we had not removed the rest of NAND
support when saying we didn't have NAND, so instead use that to key off
of rather than NANDFLASH_SIZE.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The value CONFIG_DB_784MP_GP is only used in the DDR code to refer to
CONFIG_TARGET_DB_MV784MP_GP so just use that second value directly.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We only set one of these values ever at this point, so remove dead code.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
There are a handful of variants around CONFIG_SYS_USE_DATAFLASH and none
of them now control anything further within their board config.h files,
so remove these from CONFIG_SYS_EXTRA_OPTIONS and then remove the empty
blocks in the board config.h files. In a few places further clean up
related logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LPUART
CONFIG_LPUART_32B_REG
And note that CONFIG_LPUART_32B_REG is unused in code.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one place, so pick a more direct name and
migrate to Kconfig. Rework the code slightly.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MCFRTC
CONFIG_SYS_MCFRTC_BASE
While at it, remove '#undef RTC_DEBUG' from these config files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Both of these variables are used in a few hard-coded ways to set some
string values or print something to the user. In almost all cases, it's
just as useful to hard-code the value used. The exception here is
printing something closer to correct board name for p1_p2_rdb machines.
This can be done using something from the device tree, but for now
hard-code a non-CONFIG based value instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTM_NETBSD
CONFIG_BOOTM_RTEMS
CONFIG_DESIGNWARE_WATCHDOG
CONFIG_DISPLAY_CPUINFO
CONFIG_DM_ETH
CONFIG_DM_MMC
CONFIG_DM_REGULATOR
CONFIG_DM_SPI
CONFIG_DM_SPI_FLASH
CONFIG_ISO_PARTITION
CONFIG_OF_SEPARATE
CONFIG_SPI_FLASH_WINBOND
CONFIG_SPL_ETH
CONFIG_TIMER
CONFIG_USB_DWC3
CONFIG_USB_DWC3_GADGET
CONFIG_USB_DWC3_OMAP
CONFIG_USB_DWC3_PHY_OMAP
CONFIG_USB_EHCI_TEGRA
CONFIG_USB_GADGET_DOWNLOAD
CONFIG_USB_GADGET_DUALSPEED
CONFIG_USB_GADGET_MANUFACTURER
CONFIG_USB_GADGET_PRODUCT_NUM
CONFIG_USB_GADGET_VBUS_DRAW
CONFIG_USB_GADGET_VENDOR_NUM
This catches a number of cases where board config files were #undef
various CONFIG options when building SPL, and that doesn't work. Clean
up the related comments as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit enhances mkimage to update the node
/image/pre-load/sig with the public key.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Add a stage pre-load to the command bootm.
Right now, this stage may be used to read a
header and check the signature of the full
image.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Add a stage pre-load that could
check or modify an image.
For the moment, only a header with a signature is
supported. This header has the following format:
- magic : 4 bytes
- version : 4 bytes
- header size : 4 bytes
- image size : 4 bytes
- offset image signature : 4 bytes
- flags : 4 bytes
- reserved0 : 4 bytes
- reserved1 : 4 bytes
- sha256 of the image signature : 32 bytes
- signature of the first 64 bytes : n bytes
- image signature : n bytes
- padding : up to header size
The stage uses a node /image/pre-load/sig to
get some informations:
- algo-name (mandatory) : name of the algo used to sign
- padding-name : name of padding used to sign
- signature-size : size of the signature (in the header)
- mandatory : set to yes if this sig is mandatory
- public-key (madatory) : value of the public key
Before running the image, the stage pre-load checks
the signature provided in the header.
This is an initial support, later we could add the
support of:
- ciphering
- uncompressing
- ...
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The SPL does not update the memory node with the dram size from EEPROM
but instead we can use get_ram_size which does a simple memory test
to determine the available RAM. Update PHYS_SDRAM_SIZE to 4GiB as that
is the max used on the Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Most CCF drivers follow a common pattern where their clock ops defer the
actual operation to the backing CCF clock. Add some generic implementations
of these functions to reduce duplication of code.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220320203446.740178-1-seanga2@gmail.com
Most callers of this function do not check the return value, and it is
unclear what action they should take if it fails. If a function is freeing
multiple clocks, it should not stop just because the first one failed.
Since the callbacks can no longer fail, just convert the return type to
void.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220115222504.617013-8-seanga2@gmail.com
When freeing a clock there is not much we can do if there is an error, and
most callers do not actually check the return value. Even e.g. checking to
make sure that clk->id is valid should have been done in request() in the
first place (unless someone is messing with the driver behind our back).
Just return void and don't bother returning an error.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220115222504.617013-2-seanga2@gmail.com
The 2x256 MiB SF variant of this system has 192 MiB rootfs MTD partition
containing UBI on SF0, use the correct size in U-Boot environment, else
U-Boot cannot mount UBI and boot on this variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VIDEO_BCM2835
This is the final ad-hoc CONFIG_VIDEO_... to convert.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Previous u-boot code changed the default bch setting behavior and caused
backward compatible issue. This fix choose the legacy bch geometry back
again as the default option. If the minimum ecc strength that NAND chips
required need to be chosen, it can be enabled by either adding DT flag
"fsl,use-minimum-ecc" or CONFIG_NAND_MXS_USE_MINIMUM_ECC in configs. The
unused flag "fsl,legacy-bch-geometry" get removed.
Fixes: 51cdf83eea (mtd: gpmi: provide the option to use legacy bch geometry)
Fixes: 616f03daba (mtd: gpmi: change the BCH layout setting for large oob NAND)
Tested-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add missing MEMA - MEMD register definitions for PFUZE100.
Based on work from Heiko Schocher <hs@denx.de>.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Macros PCI_CLASS_CODE_* and PCI_CLASS_SUB_CODE_* are unused and are
duplication of PCI_CLASS_* macros defined in pci_ids.h header file.
So remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add following two new PCI class codes defines into pci_ids.h include file:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
And use these defines in all U-Boot code for describing PCI class codes for
normal and subtractive PCI bridges.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FAULT_ECHO_LINK_DOWN
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91_WANTS_COMMON_PHY
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The block IO protocol may be installed on any handle. We should make
no assumption about the structure the handle points to.
efi_disk_is_system_part() makes an illegal widening cast from a handle
to a struct efi_disk_obj. Remove the function.
Fixes: Fixes: 41fd506842 ("efi_loader: disk: add efi_disk_is_system_part()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Let function efi_dp_find_obj() additionally check if a given protocol is
installed on the handle relating to the device-path.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
efi_dp_find_obj() should not return any handle with a partially matching
device path but the handle with the maximum matching device path.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LEGACY
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91_GPIO_PULLUP
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This variable is used once and is noted as board-specific. Use the
value directly with a comment.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is used only once, and in comparison with an unset symbol,
so drop it.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G10EK
CONFIG_AT91SAM9261EK
CONFIG_AT91SAM9G10
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G20EK
CONFIG_AT91SAM9260EK
CONFIG_AT91SAM9G20EK_2MMC
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AM335X_USB0
CONFIG_AM335X_USB0_MODE
CONFIG_AM335X_USB1
CONFIG_AM335X_USB1_MODE
We do this by introducing specific options for static configuration of
USB0/USB1 in SPL rather than defining CONFIG_AM335X_USBx_MODE to the
enum value being used. Furthermore, with how the code is used now we do
not need to have OTG mode exposed as an option here, so remove that.
Signed-off-by: Tom Rini <trini@konsulko.com>
With all boards now using DM_ETH we determine the value for
CONFIG_FEC_XCV_TYPE at run time, except in the case of the default
fall-back. Set the fallback directly now.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ETHPRIME
This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME
similar to other options that are not always set and control environment
variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts removes the following symbols:
CONFIG_HAS_ETH0
CONFIG_HAS_ETH1
CONFIG_HAS_ETH2
CONFIG_HAS_ETH3
This is because at this point, only the ids8313 platform was using the
code which was controlled by these symbols. In turn, this code already
performs error checking on being able to perform the device tree fixup.
Rather than convert these to Kconfig for a single platform, update the
code to not need these checks and remove them from all the platforms
they were unused on.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOT_RETRY_TIME
CONFIG_BOOT_RETRY_MIN
CONFIG_RESET_TO_RETRY
We also introduce CONFIG_BOOT_RETRY to gate these options, and clean up
the associated Makefile entry and C code for picking default values of
CONFIG_BOOT_RETRY_MIN.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ARMV8_SWITCH_TO_EL1
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
This converts the following to Kconfig:
CONFIG_ARMV7_SECURE_BASE
CONFIG_ARMV7_SECURE_MAX_SIZE
CONFIG_ARMV7_SECURE_RESERVE_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
As the CI test for stopping platforms from being merged that were
defining symbols that had Kconfig entries, a small number of symbols
needed to be migrated again. Do so, and catch two cases the README
should also have been updated but was not.
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit re-introduced a migrated CONFIG symbol to the board header
file. These changes should likely be handled via documentation instead,
as well.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We cannot define a CONFIG value here to ensure that the Kconfig value
isn't set wrong.
Fixes: 2c699fe0d3 ("configs: sunxi: Add common SUNIV header")
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Kevin, an RK3399-based convertible chromebook that is
very similar to Bob. This patch is mostly based on existing support for
Bob, with only minor changes for Kevin-specific things.
Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV,
so adjust it here in the dts as well. The rk3399-gru-kevin devicetree
has an unknown event code reference which has to be defined, set it
to the Linux counterpart. The new defconfig is copied from Bob with the
diffconfig:
DEFAULT_DEVICE_TREE "rk3399-gru-bob" -> "rk3399-gru-kevin"
DEFAULT_FDT_FILE "rockchip/rk3399-gru-bob.dtb" -> "rockchip/rk3399-gru-kevin.dtb"
VIDEO_ROCKCHIP_MAX_XRES 1280 -> 2400
VIDEO_ROCKCHIP_MAX_YRES 800 -> 1600
+TARGET_CHROMEBOOK_KEVIN y
With this Kevin can boot from SPI flash to a usable U-Boot prompt on the
display with the keyboard working, but cannot boot into Linux for
unknown reasons.
eMMC starts in a working state but fails to re-init, microSD card works
but at a lower-than-expected speed, USB works but causes a hang on
de-init. There are known workarounds to solve eMMC and USB issues.
Cc: Marty E. Plummer <hanetzer@startmail.com>
Cc: Simon Glass <sjg@chromium.org>
[Alper: commit message, resync config with Bob, update MAINTAINERS,
add to Rockchip doc, add Kconfig help message, set regulator]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This patch enables some configs that should be working on the Bob board,
based on what is observed to work on the Kevin board.
The Bob board uses an Embedded DisplayPort panel compatible with the
simple panel and Rockchip eDP drivers. Its backlight is controlled by
the Chromium OS Embedded Controller Pulse Width Modulator. Enable these
for the board.
Also set VIDEO_ROCKCHIP_MAX_{XRES,YRES} to 1280x800, the resolution of
its panel. This had to be done for the Kevin board, but it's untested if
this is actually necessary for Bob.
The Rockchip video driver needs to assert/deassert some resets, so also
enable the reset controller. RESET_ROCKCHIP defaults to y for this board
when DM_RESET=y, so it's enough to set that.
The Bob board has two USB 3.0 Type-C ports and one USB 2.0 Type-A port
on its right side. Enable the configs relevant to USB devices so these
can be used. This is despite a known issue with RK3399 boards where USB
de-init causes a hang, as there is a known workaround.
Some other rk3399-based devices enable support for the SoC's random
number generator in commit a475bef534 ("configs: rk3399: enable rng on
firefly/rock960/rockpro64"), as it can provide a KASLR seed when booting
using UEFI. Enable it for Bob as well.
The default misc_init_r() for Rockchip boards sets cpuid and ethernet
MAC address based on e-fuse block. A previous patch extends this on Gru
boards to set registers related to SoC IO domains as is necessary on
these boards. Enable this function and configs for it on Bob.
The microSD card slot on this board (and others based on Gru) is
connected to a GPIO controlled regulator (ppvar-sd-card-io), which must
be operable by U-Boot. Enable the relevant config option to allow this.
Bob boards also use the Winbond W25Q64DW SPI flash chip, enable support
for Winbond SPI flash chips in the board config so U-Boot can boot with
this chip.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYjIBkgAKCRDKSWXLKUoM
IYUwAKCYRBxb59BFq4MRvTbNcRZ7H4oGIQCfVUl3x9KZ7nFZaYAaBXFBxwna+PE=
=irCR
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.07-rc1
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
Delegate setting the Enhanced Strobe configuration to individual drivers
if they set a function for it. Return -ENOTSUPP if they do not, like
what the MMC uclass does.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
After commit f132aab403 ("Revert "mmc: fsl_esdhc_imx: use
VENDORSPEC_FRC_SDCLK_ON to control card clock output""), it
involve issue in mmc_switch_voltage(), because of the special
design of usdhc.
For FSL_USDHC, it do not implement VENDORSPEC_CKEN/PEREN/HCKEN/IPGEN,
these are reserved bits(Though RM contain the definition of these bits,
but actually internal IC logic do not implement, already confirm with
IC team). Instead, use VENDORSPEC_FRC_SDCLK_ON to gate on/off the card
clock output. Here is the definition of this bit in RM:
[8] FRC_SDCLK_ON
Force CLK output active
Do not set this bit to 1 unless it is necessary. Also, make sure that
this bit is cleared when uSDHC’s clock is about to be changed (frequency
change, clock source change, or delay chain tuning).
0b - CLK active or inactive is fully controlled by the hardware.
1b - Force CLK active
In default, the FRC_SDCLK_ON is 0. This means, when there is no command
or data transfer on bus, hardware will gate off the card clock. But in
some case, we need the card clock keep on. Take IO voltage 1.8v switch
as example, after IO voltage change to 1.8v, spec require gate off the
card clock for 5ms, and gate on the clock back, once detect the card
clock on, then the card will draw the dat0 to high immediately. If there
is not clock gate off/on behavior, some card will keep the dat0 to low
level. This is the reason we fail in mmc_switch_voltage().
To fix this issue, and concern that this is only the fsl usdhc hardware
design limitation, set the bit FRC_SDCLK_ON in the beginning of the
wait_dat0() and clear it in the end. To make sure the 1.8v IO voltage
switch process align with SD specification.
For standard tuning process, usdhc specification also require the card
clock keep on, so also add these behavior in fsl_esdhc_execute_tuning().
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Update the LZ4 compression module based on LZ4 v1.8.3 in order to
use the newest LZ4_decompress_safe_partial() which can now decode
exactly the nb of bytes requested.
Signed-off-by: Huang Jianan <jnhuang95@gmail.com>
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
- convert Nokia RX-51 to CONFIG_DM_VIDEO
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYi+zvw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXIReAJ9JS06uOjNFmOBdfpsOI2jnVdWABQCbB8nvUh19
jbftZtj+18fhFuNb1r4=
=3vpL
-----END PGP SIGNATURE-----
Merge tag 'video-20220314' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix display of the u-boot logo on Apple devices
- convert Nokia RX-51 to CONFIG_DM_VIDEO
Xilinx ZynqMP SOC can set 6 parameters for its pins. pinmux status
command will print the status of these parameters for each pin. But
current print buffer length is only 40 characters long, increase it
to 80 to print all the parameters.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/3a6be84c8354f38754a9838670cc0319e84f29e8.1645626183.git.michal.simek@xilinx.com
InstallProtocolInterface() is called with a pointer to the protocol GUID.
There is not guarantee that the memory used by the caller for the protocol
GUID stays allocated. To play it safe the GUID should be copied to U-Boot's
internal structures.
Reported-by: Joerie de Gram <j.de.gram@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
QSGMII PHY initialization should only be done for J721E EVMs and not for
J721E-SK boards. Therefore, fix the environment variables accordingly.
Also, by default remote processors should not be booted in U-Boot but
rather be left to the users to enable this by setting dorprocboot.
Therefore, remove dorprocboot that is being set by default.
Fixes: 5980925e2a ("include: configs: j721e_evm: Add support to boot ethfw core in j721e")
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Generate events when devices are probed or removed, allowing hooks
to be added for these situations.
This is controlled by the DM_EVENT config option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to create and dispatch events without needing to allocate
memory. Also add a way to 'spy' on events, thus allowing 'hooks' to be
created.
Use a linker list for static events, which we can use to replace functions
like arch_cpu_init_f(). Allow an EVENT_DEBUG option which makes it
easier to see what is going on at runtime, but uses more code space.
Dynamic events allow the creation of a spy at runtime. This is not always
necessary, but can be enabled with EVENT_DYNAMIC if needed.
A 'test' event is the only option for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Mechanically convert video_hw_init() function to UCLASS_VIDEO probe
callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.
As framebuffer base address is setup by the bootloader which loads U-Boot,
set plat->base to that fixed framebuffer address.
This change was tested in qemu n900 machine and is working fine.
What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.
Signed-off-by: Pali Rohár <pali@kernel.org>
Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.
DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml
The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com
Most of the frequencies are not rounded up to a proper number.
When we need to devide these frequencies to get a number for example
frequency in Mhz, we see it as one less than the actual intended value.
Ex: If we want to get Mhz from frequency 199999994hz, we will calculate
it using div64_u64(199999994, 1000000) and we will get 199Mhz in place
of 200Mhz.
Add a macro DIV64_U64_ROUND_UP for rounding up div64_u64. This is taken
from linux 'commit 68600f623d69("mm: don't miss the last page because of
round-off error")'.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f9fdcba76cd692ae436b1d7883b490e3dc207231.1645626962.git.michal.simek@xilinx.com
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Currently, any u-boot bootloader for ti armv7 platforms using
DEFAULT_FIT_TI_ARGS to boot with a fitimage (boot_fit = 1)
doesn't boot when built with Yocto Poky (openembedded-core).
## Loading kernel from FIT Image at 90000000 ...
Could not find configuration node
ERROR: can't get kernel image!
Arago forked the kernel-fitimage class [1] and altered the
configuration nodes naming while adding the OPTEE support by
using FITIMAGE_CONF_BY_NAME by default [2].
The "upstream" kernel-fitimage class from openembedded-core still
add the "conf-" prefix for each configuration nodes [3].
The ITS file format (from doc/uImage.FIT/source_file_format.txt)
is not really accurate with the expected naming of these nodes.
But in practice the "conf-" prefix is widely used.
When the FIT image support has been added for ti armv7 platforms
the naming from Arago has been used [3]. Fix this issue by adding
the prefix expected by the ITS file generated by kernel-fitimage
class from openembedded-core.
[1] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=719ab1b2098bcdc59c249e3529fa82cb1b9130e6
[2] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=f23f2876a0cda89241d031bb7ba0b4256ed90035
[3] https://git.openembedded.org/openembedded-core/tree/meta/classes/kernel-fitimage.bbclass?h=yocto-3.1.13#n290
[3] 1e93cc8473
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Denys Dmytriyenko <denys@konsulko.com>
This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These particular values are not configurable and today we always set
CONFIG_SECURE_BL1_ONLY. Move these to where they're used in the code,
and drop from the CONFIG namespace.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Remove some code, primarily CPM2 related, that is now unused since the
removal of MPC8540/60ADS.
Fixes 3913191c8a ("powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implements SCMI APIs to retrieve the number exposed SCMI clocks using
SCMI_PROTOCOL_ATTRIBUTES messages and the names of the clocks using
SCMI_CLOCK_ATTRIBUTES messages.
This change updates sandbox SCMI clock test driver to manage these
2 new message IDs.
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Clement Leger <clement.leger@bootlin.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Changes devm_scmi_process_msg() first argument from target parent device
to current SCMI device and lookup the SCMI agent device among SCMI device
parents for find the SCMI agent operator needed for communication with
the firmware.
This change is needed in order to support CCF in clk_scmi driver unless
what CCF will fail to find the right udevice related to exposed SCMI
clocks.
This patch allows to simplify the caller sequence, using SCMI device
reference as parameter instead of knowing SCMI uclass topology. This
change also adds some protection in case devm_scmi_process_msg() API
function is called for an invalid device type.
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().
Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The BOOT_TARGET_DEVICES list for distro_bootcmd was hard-coded to assume
that all boot devices are available/enabled in the configuration,
thus ignoring the actual config settings. The config_distro_bootcmd.h
header file specifically has compile-time checks to detect such problems.
To allow disabling USB, SCSI, etc. in custom lx2160a board configs,
make it depend on the config settings and use only the enabled features.
Signed-off-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Most of the time it is very useful to have the version of the board
management controller. Now that we have a driver, print it during
startup.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a multi-function device driver which will probe its children and
provides methods to access the device.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds a helper function for clk_get_by_name in cases where the clock is
optional. Hopefully this helps point driver writers in the right direction.
Also convert some existing users.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220115205247.566210-2-seanga2@gmail.com
This converts the existing driver API docs (clk-uclass.h) to kernel doc
format and adds them to the HTML documentation. Because the kernel doc
sphinx converter does not handle functions in structs very well, the
individual methods are documented separately. This is primarily inspired by
the phylink documentation [1], which uses this trick extensively.
[1] https://www.kernel.org/doc/html/latest/networking/kapi.html#c.phylink_mac_ops
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20211222171114.3091780-5-seanga2@gmail.com
This converts the existing client (aka clk.h) documentation to kernel doc
format, and adds it to the HTML docs. I have tried to preserve existing
comments as much as possible, refraining from semantic changes.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20211222171114.3091780-4-seanga2@gmail.com
[rebased onto u-boot/master and resolved conflicts]
Signed-off-by: Sean Anderson <seanga2@gmail.com>
The optional varients of clk_get_* functions are just simple wrappers.
Reduce code size a bit by inlining them. On platforms where it is not used
(most of them), it will not be compiled in any more. On platforms where
they are used, the inlined branch should not cause any significant growth.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20211222171114.3091780-3-seanga2@gmail.com
These symbols are incorrect, meaning that binman cannot find the
associated entry. This leads to errors like:
binman: Section '/binman/simple-bin': Symbol '_binman_spl_prop_size'
in entry '/binman/simple-bin/u-boot-spl/u-boot-spl-nodtb':
Entry 'spl' not found in list (mkimage,u-boot-spl-nodtb,
u-boot-spl-bss-pad,u-boot-spl-dtb,u-boot-spl,u-boot-img,main-section)
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Use the complete 512kb (4 blocks) nand partition reserved for u-boot
environment instead of just the first block, this allows the module to
have a working environment even if 3 blocks are bad.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- a37xx: pci: Cleanup and minor fix for root port check (Pali)
- pci: mvebu: Ensure that root port is always on root zero bus (Pali)
- kwbimage: Fix dumping DATA registers for v0 images (Pali)
- kwbimage: Support for parsing extended v0 format (Pali)
- a37xx: Fix code and update DTS files to upstream version (Pali)
- a37xx: Fix and extend building memory map (Pali)
- ddr: marvell: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision (Marek)
- mvebu: Optionally reset board on DDR training failure (Marek)
This change updates all Armada 37xx DTS files to version which is used by
Linux kernel v5.18.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI config space of the aardvark PCIe Root Port is available only in
internal aardvark memory space starting at offset 0x0. PCI Express
registers (PCI_EXP_*) start at offset 0xc0. And Advanced Error Reporting
registers (PCI_ERR_*) start at offset 0x100.
Replace custom aardvark register macros by standard PCI macros from
include/pci.h file with fixed offset.
Some DEVCTL and AER macros are not defined in include/pci.h file, so define
them in the same way as in linux uapi header file pci_regs.h.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that single defconfig can be used for booting J721E EVM and
SK, default device tree will not work for selecting dtb for
kernel. Update the findfdt env to select right dtb based on
board_name env variable.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
This function has not been conditionally compiled for some time, so
remove the incorrect guards around the declaration.
Signed-off-by: Tom Rini <trini@konsulko.com>
Driver should be enabled by CONFIG_POWER_DOMAIN=y and
CONFIG_ZYNQMP_POWER_DOMAIN=y. Power domain driver doesn't have own DT node
but it uses zynqmp firmware DT node that's why there is a need to bind
driver when firmware node is found.
Driver itself is simple. It is sending pmufw config object overlay for
enabling access to device which is done in ...domain_request().
In ...domain_on() capabilities are passed and node is requested.
This should be bare minimum of required to get power domain driver working.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/f4b9433b91c0b18c375b061c7a4e29d428f70547.1644226055.git.michal.simek@xilinx.com
When parsing the dfu_alt_info, check the number of arguments
and argument string strictly. If there is any garbage data
(which is not able to be parsed correctly) in dfu_alt_info,
that means something wrong and user may make a typo or mis-
understanding about the syntax. Since the dfu_alt_info is
used for updating the firmware, this mistake may lead to
brick the hardware.
Thus it should be checked strictly for making sure there
is no mistake.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
this will add kaslrseed keyword to sysboot lable,
when it set, it will request to genarate random number
from hwrng as kaslr-seed.
with this patch exlinux.conf label looks like
label l0
menu testing
linux /boot/vmlinuz-5.15.16-arm
initrd /boot/initramfs-5.15.16-arm.img
fdtdir /boot/dtbs/5.15.16-arm/
kaslrseed
append root=UUID=92ae1e50-eeeb-4c5b-8939-7e1cd6cfb059 ro
Tested on Khadas VIM with kernel 5.16.0-rc5-arm64, Debian 11.
Signed-off-by: Zhang Ning <zhangn1985@qq.com>
The imx8mm and imx8mn appear compatible with imx7d-usb
flags in the OTG driver. If the dr_mode is defined as
host or peripheral, the device appears to operate correctly,
however the auto host/peripheral detection results in an error.
The solution isn't just adding checks for imx8mm and imx8mn to
the check for imx7, because the USB clock needs to be running
to read from the USBNC_PHY_STATUS_OFFSET register or it will hang.
Marek requested that I not enable the clocks in ehci_usb_of_to_plat,
so I modified that function to return an unknown state if the
device tree does not explicitly state whether it is a host
or a peripheral.
When the driver probes, it looks to see if it's in the unknown
state, and only then will it read the register to auto-detect.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
There are no boards that define CONFIG_SYS_RESET_ADDR, so drop the
remaining comments referencing it and also the config_whitelist.txt entry.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: thomas@wytron.com.tw
This driver adds support for the keyboard on Apple Silicon laptops.
The controller for this keyboard sits on an SPI bus and uses an
Apple-specific HID over SPI protocol. The packets sent by this
controller for key presses and key releases are fairly simple and
are decoded directly by the code in this driver and converted into
standard Linux keycodes. The same controller handles the touchpad
found on these laptops. Packets for touchpad events are simply
ignored.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
This mailbox driver provides a communication channel with the
Apple IOP controllers found on Apple SoCs. These IOP controllers
are used to implement various functions such as the System
Manegement Controller (SMC) and NVMe storage. It allows sending
and receiving a 96-bit message over a single channel.
The header file with the struct used for mailbox messages is taken
straight from Linux.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
binman fit improvements
ACPI fixes and making MCFG available to ARM
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmIEGscRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZVkwf/RO9qLM/qtpcvtzFTciVFa/GQwd922abw
Anc4DYDBFTWfVymBTZT4Te0luTkZpqBV9cLEGw4XGYKGt+daVYB4cNKknKDOWqLI
adF7xHK2utT3OBlR7pL4d0Rvq0DAAFmyizkbi/CKHhrrpPkW8rPEiZlMwi+WQlTb
9Qv3deoVnRn3ivgw3AnTny+S52IFuI9pH4a34ASWfpOi3gGzICtIAnhVpRXdD+3A
TIhgK6XaGxBc0lVThsqc20FWfZ6rb4WyBRTRgbYivHn/fQxkynxBdSD6WU1ZdGH8
UZGjk5wBIkf+OyHjNQo/VEwoRHXR1k435+gsehUV8LvzytUykzP/FA==
=7Gel
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-8feb22-take3' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
patman snake-case conversion
binman fit improvements
ACPI fixes and making MCFG available to ARM
[trini: Update scripts/pylint.base]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert
to Driver Model and use uclass mvgbe and the compatible driver M88E1118R
to bring up Ethernet.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- As the result of the migration to Driver Model, this u-boot image has
grown substantially (about 100K, give or take). The old envs location
at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K).
- Miscellaneous changes: Move constants to .c file and remove header file
board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to
keep u-boot image under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Dockstar board has the network chip Marvell 88E1116R. Convert to
Ethernet driver model, and use uclass mvgbe and the compatible driver
M88E1118R to bring up Ethernet.
- Add CONFIG_DM_ETH and associated configs.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Add CONFIG_PHY_MARVELL to properly configure the network.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Miscellaneous changes: Move constants to .c file and remove
header file board/Seagate/dockstar/dockstar.h, use
CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, add CONFIG_HUSH_PARSER, use BIT macro, and cleanup comments.
- Note: This patch is a RESEND for a previous patch:
https://patchwork.ozlabs.org/project/uboot/patch/20210812051854.1340-2-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Miscellaneous changes: Move constants to .c file and remove header file
board/iomega/iconnect/iconnect.h. Add CONFIG_HUSH_PARSER, use BIT macro,
and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Globalscale Technologies Dreamplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network
port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned,
could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/dreamplug/dreamplug.h, cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Use parenthesis for the device_get_ops macro argument. This prevents
errors when using an expression for the parameter.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE
Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is defined based on two other CONFIGs for all boards except sandbox
and durian.
For sandbox the value does not matter. For durian the value seems
excessive.
Drop the option completely, to simplify configuration and reduce the
number of things we need to convert to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_IDE_MAXBUS
CONFIG_SYS_IDE_MAXDEVICE
CONFIG_SYS_ATA_BASE_ADDR
CONFIG_SYS_ATA_STRIDE
CONFIG_SYS_ATA_DATA_OFFSET
CONFIG_SYS_ATA_REG_OFFSET
CONFIG_SYS_ATA_ALT_OFFSET
CONFIG_SYS_ATA_IDE0_OFFSET
CONFIG_SYS_ATA_IDE1_OFFSET
CONFIG_ATAPI
CONFIG_IDE_RESET
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the new IF_ENABLED_INT() feature to avoid needing our own inline
function to handle this case. Tidy up the logic to ensure that the value
is only used when present. Update the 'expected' comment also.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if an optional Kconfig value needs to be used it must be
bracketed by #ifdef. For example, with this Kconfig setup:
config WIBBLE
bool "Support wibbles, the world needs more wibbles"
config WIBBLE_ADDR
hex "Address of the wibble"
depends on WIBBLE
then the following code must be used:
#ifdef CONFIG_WIBBLE
static void handle_wibble(void)
{
int val = CONFIG_WIBBLE_ADDR;
...
}
#endif
static void init_machine()
{
...
#ifdef CONFIG_WIBBLE
handle_wibble();
#endif
}
Add a new IF_ENABLED_INT() to help with this. So now it is possible to
write, without #ifdefs:
static void handle_wibble(void)
{
int val = IF_ENABLED_INT(CONFIG_WIBBLE, CONFIG_WIBBLE_ADDR);
...
}
static void init_machine()
{
...
if (IS_ENABLED(CONFIG_WIBBLE))
handle_wibble();
}
The value will be CONFIG_WIBBLE_ADDR if CONFIG_WIBBLE is defined and will
produce a build error if not.. This allows us to reduce the use of #ifdef
in the code, ensuring that the compiler still checks the code even if it
is not ultimately used for a particular build.
Add a CONFIG_IF_ENABLED_INT() version as well.
If an attempt is made to use a value that does not exist (i.e. when the
conditional is not enabled), an error about a non-existing function is
generated, e.g.:
common/bloblist.c:447: undefined reference to `invalid_use_of_IF_ENABLED_INT'
Signed-off-by: Simon Glass <sjg@chromium.org>
The config_enabled() macro currently uses 0 as the default value. Update
it to allow any value, so we can pass it something else, such as a
non-existent function, to produce a build error if it is not defined.
Also tidy up the code style for IS_ENABLED() and drop the unnecessary
brackets (the value is a simple 0 or 1).
Signed-off-by: Simon Glass <sjg@chromium.org>
Add remoteproc resource handling helpers. These functions
are primarily to parse the resource table and to handle
different types of resources. Carveout, devmem, trace &
vring resources are handled.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[Amjad: fix redefinition of "struct resource_table" and compile warnings ]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Add find_next_zero_area to fetch the next zero area in the map.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Add pinctrl macros for J721S2 SoC. These macro definitions are
similar to that of J721E, but adding new definitions to avoid
any naming confusions in the soc dts files.
checkpatch insists the following error exists:
ERROR: Macros with complex values should be enclosed in parentheses
However, we do not need parentheses enclosing the values for this
macro as we do intend it to generate two separate values as has been
done for other similar platforms.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
There are 4 lanes in the single instance of J721S2 SERDES. Each SERDES
lane mux can select upto 4 different IPs. Define all the possible
functions.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Move setting the default boot command to the
apalis/colibri_imx6_defconfig. It allows replacing the command
without code modification.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
When loading an EFI binary via the UART we assign a UART device path to it.
But we lack a handle with that device path.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update to the 5.16 imx8mq dts files and dt bindings
Changes since v1:
Dropped rfkill.h that is not in linux mainline yet.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add binding for reference clock PAD modes of the i.MX8 PCIe PHY.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1638432158-4119-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de> # Pick from Linux f6f787874aa5 ("dt-bindings: phy: phy-imx8-pcie: Add binding for the pad modes of imx8 pcie phy")
The Linux Kernel Image size for arm64 is still growing.
A Kernel with 54 MB at load address 0x80280000 overlaps
with fdt_addr at 0x83000000. So let's increase it to 0x84000000
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Commit 72d81360aa ("global: Convert CONFIG_LOADADDR to
CONFIG_SYS_LOADADDR") dropped the usage of LOADADDR and replaced it with
SYS_LOADADDR.
Use the correct macro in environment by replacing CONFIG_LOADADDR with
CONFIG_SYS_LOADADDR.
Fixes: d75ebf3482 ("imx: ventana: fix splash logo drawing")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Add fdt_addr_r fdtfile which used by distro boot, and cleanup legacy
environment variables.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
We changed to single flash.bin now. So dfu_alt_info should be modified
to reflect this change.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The PDK2 board is capable of running both 100M and 1G ethernet. However,
the i.MX6 has only one ethernet MAC, so it is possible to configure
either 100M or 1G Ethernet. In case of 100M option, the PHY is on the
SoM and the signals are routed to a RJ45 port. For 1G the PHY is on
the PDK2 board with another RJ45 port. 100M and 1G ethernet use
different signal pins from the i.MX6, but share the MDIO bus.
This SoM board combination is used to demonstrate how to enable 1G
ethernet configuration.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Use the complete 512kb (4 blocks) nand partition reserved for u-boot
environment instead of just the first block, this allows the module
to have a working environment even if 3 blocks are bad.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
This is the promised second part of the sunxi PR for 2022.04, albeit
technially outside of the merge window. We were working on this full
steam since the beginning of the year, and it deserves to be merged,
I think.
The main attraction is support for the F1C100s SoC, which sports a
venerable ARM926 core. Support for this SoC and the LicheePi Nano board
has been in Linux for years, and U-Boot patches were posted mid last
year already.
The new SoC using ARMv5 also means that the bulk of the new code should
not touch any existing boards, although we did some refactorings first,
of course, which actually cleans up some existing sunxi code.
Compile tested for all 160 sunxi boards, and briefly tested on BananaPi M1,
OrangePi Zero, Pine64 and Pine-H64. Tested by others on their boards,
including F1C100s and F1C200s devices.
Add device tree files for suniv and
Lichee Pi Nano it is a board based on F1C100s.
dt-bindings/dts are synced with 5.16.0
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Adds support for SUNIV and the F1C100s.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Remove some pointless #ifdefs from this file, as there are quite too
many of them already.
Some definitions don't really hurt to have in any case, so remove the
pointless CONFIG_MMC guard around CONFIG_MMC_SUNXI_SLOT.
The BOARD_SIZE_LIMIT applies regardless of ARM64 or not (now), so remove
that guard as well. The maximum number of MMC devices does not depend on
CONFIG_ENV_IS_IN_MMC, so move that out to simplify the file.
Last but not least CONFIG_SPL_BOARD_LOAD_IMAGE serves no real purpose
anymore: it's unconditionally defined for all sunxi boards, and protects
nothing applicable outside of sunxi code anymore. Just remove it.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At present we use wide characters for unicode but this is not necessary.
Change the code to use the 'u' literal instead. This helps to fix build
warnings for sandbox on rpi.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Field fail-safe u-boot update procedure for pg-wcom boards is defined and
implemented by patch: 59b3403.
This patch invokes the update procedure for pg-wcom-ls102x designs during
early misc_init_f execution.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The GoFlex Home board has the network chip Marvell 88E1116R.
Use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: use CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
a bit delayed, the first batch of the sunxi pull request for this cycle.
This is mostly collecting some patches that were lying around for a
while, plus some recent fixes. Nothing too exciting at this point, but
of course they should be merged nevertheless.
There is the much bigger F1C100s SoC support coming up, which I hope to
be able to send in the next few days, along with the removal of sunxi's
lowlevel_init usage.
Compile tested for all 159 sunxi boards, plus briefly tested on BananaPi
M1, OrangePi Zero, Pine64 and Pine-H64.
Most AXP PMICs feature a "startup source" register, which keeps
information about how the PMIC started operation. Bit 0 in there means
it has been started by "plugging in the power cable".
Define a symbol in each PMIC's header file to be able to use that
register and bit later on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Documentation:
* update Nokia RX-51 documentation and move it to rst
* describe boot switch settings for HiFive Unmatched board
UEFI:
* fix the checking of images hashes and signatures
* provide the RISCV_EFI_BOOT_PROTOCOL
-----BEGIN PGP SIGNATURE-----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=+edp
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc1-3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1-3
Documentation:
* update Nokia RX-51 documentation and move it to rst
* describe boot switch settings for HiFive Unmatched board
UEFI:
* fix the checking of images hashes and signatures
* provide the RISCV_EFI_BOOT_PROTOCOL
A mix of signatures and hashes in db doesn't always work as intended.
Currently if the digest algorithm is not explicitly set to sha256 we
stop walking the security database and reject the image.
That's problematic in case we find and try to check a signature before
inspecting the sha256 hash. If the image is unsigned we will reject it
even if the digest matches.
Since we no longer reject the image on unknown algorithms add an explicit
check and reject the image if any other hash algorithm apart from sha256
is detected on dbx.
Suggested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This adds support for new RISCV_EFI_BOOT_PROTOCOL to
communicate the boot hart ID to bootloader/kernel on RISC-V
UEFI platforms.
The specification of the protocol is hosted at:
https://github.com/riscv-non-isa/riscv-uefi
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
With Ethboot support in SPL, network stack requires more BSS area, so
increase BSS max size to 16K
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add to support rsa 3072 bits algorithm in tools
for image sign at host side and adds rsa 3072 bits
verification in the image binary.
Add test case in vboot for sha384 with rsa3072 algorithm testing.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently the names MMC1, MMC2 and MMC2_2 are output in the SPL. To
achieve more userbility here the name of the boot source can be returned.
E.g. for "MMC1" -> "eMMC" or "MMC2" -> "SD card".
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmHyEeYRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYYlgf8C7tQVklXz9ZHhxVrFaPHWwgmBzEZJSrc
7SWhDX9yBrAYBUk8Q4OMnJz6nXW8Rz5Td9GfBNWcJag1HjJqno4BxkqwGk2tshgj
GIY0D1cGfKJzB4E6/rK/ETwmX4KVUyEf7S2IdJ0oydkn9t7OwDkUX5WtGXo70E7q
ZJGYlX5NQCVBRAF9NYDuyVFljrPzAiyT58VCtXY3q63C7PmRYvag8r56ug+8lkk3
9EbOTcwETqq9SbT1vucyBxwbUmoKhb2BF32jEcIhozowIM3GNsSpkdzQCUnylqfa
LYI/p0oVTKLfFRBRvQjLgdB/OQP8MLkby8A++Db2OW49mBXhn/5JWA==
=PdpE
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jan22' of https://source.denx.de/u-boot/custodians/u-boot-dm
acpi refactoring to allow non-x86 use
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
Add support for CDC ACM using the new UDC and gadget API. This protocol
can be used for serial over USB data transfer and is widely supported
by various OS (GNU/Linux, MS-Windows, OSX...). The usual purpose of
such link is to access device debug console and can be useful for
products not exposing regular UART to the user.
A default stdio device named 'usbacm' is created, and can be used
to redirect console to USB link over CDC ACM:
> setenv stdin usbacm; setenv stdout usbacm
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
At present mkimage displays the node information but it is not clear what
signing action was taken. Add a message that shows it. For now it only
supports showing a single signing action, since that is the common case.
Sample:
Signature written to 'sha1-basic/test.fit',
node '/configurations/conf-1/signature'
Public key written to 'sha1-basic/sandbox-u-boot.dtb',
node '/signature/key-dev'
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we rely on the key blob being in the global_data fdt_blob
pointer. This is true in U-Boot but not with tools. For clarity, pass the
parameter around.
Signed-off-by: Simon Glass <sjg@chromium.org>
When OF_LIVE flag is enabled on a 64 bits platform, there is an
issue when dev_read_addr() is called and need to perform an address
translation using __of_translate_address().
In case of error, __of_translate_address() return's value is OF_BAD_ADDR
(wich is defined in include/dm/of.h to ((u64)-1) = 0xffffffffffffffff).
The return value of dev_read_addr() is often compared to FDT_ADDR_T_NONE
which is defined as (-1U) = 0xffffffff.
In this case the comparison is always false.
To fix this issue, define FDT_ADDR_T_NONE to (ulong)(-1) in case of
AARCH64. Update accordingly related tests.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add some tables needed for ARM devices, including more MADT subtables,
a CSRT descriptor, GTDT and PPTT.
WIP: This needs comments added.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this list is used to collect items within the DSDT and SSDT
tables. It is useful for it to collect the whole tables as well, so there
is a list of what was created and which write created each one.
Refactor the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update this function to the newer style, so we can avoid passing and
returning an address through this function.
Also move this function out of the x86 code so it can be used by other
archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Move this table over to use a writer function, moving the code from the
x86 implementation.
Add a pointer to the DSDT in struct acpi_ctx so we can reference it later.
Disable this table for sandbox since we don't actually compile real ASL
code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this table over to use a writer function, moving the code from the
x86 implementation.
Add a pointer to the DSDT in struct acpi_ctx so we can reference it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new ACPI writer to write the base tables at the start of the area,
moving this code from the x86 implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present acpi_setup_base_tables() both sets up the ACPI context and
writes out the base tables.
We want to use an ACPI writer to write the base tables, so split this
function into two, with acpi_setup_ctx() doing the context set, and
acpi_setup_base_tables() just doing the base tables.
Disable the writer's write_acpi_tables() function for now, to avoid
build errors. It is enabled in a following patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we call lots of functions to generate the required ACPI tables.
It would be better to standardise these functions and allow them to be
automatically collected and used when needed.
Add a linker list to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to record the start of an ACPI table so that offsets from
that point can be easily calculated.
Add this to the context and set it before calling the writer method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow this to be used on any arch. Also convert to using macros so that
we can check the CONFIG option in C code.
Signed-off-by: Simon Glass <sjg@chromium.org>
This permits to prepare FIT image description that do not hard-code the
final choice of the signature algorithm, possibly requiring the user to
patch the sources.
When -o <algo> is specified, this information is used in favor of the
'algo' property in the signature node. Furthermore, that property is set
accordingly when writing the image.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The write operation in misc_ops already takes a "const void *" buffer,
but misc_write() takes a mutable "void *". There's no reason for this,
so make misc_write() consistent with the standard write() prototype.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today the bootcount is not managed by the Linux kernel for STM32MP15 as
we don't have driver to update the used backup register in TAMP and the
recovery command still executes the normal bootcmd with
'altbootcmd=run bootcmd'.
So the bootcount feature is never used, the config CONFIG_BOOTCOUNT_LIMIT
and the associated environment variable 'altbootcmd' can be removed to
reduce the U-Boot size.
Each boards can re-enable this feature later in their defconfig, if it is
needed, with the expected backend, for example CONFIG_BOOTCOUNT_GENERIC
or CONFIG_BOOTCOUNT_ENV.
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Documentation:
* describe printf() format codes
UEFI
* enable more algorithms for UEFI image verification, e.g. SHA256-RSA2048
General
* simplify printing short texts for GUIDs
* provide a unit test for printing GUIDs
-----BEGIN PGP SIGNATURE-----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=GoR6
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc1-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1-2
Documentation:
* describe printf() format codes
UEFI
* enable more algorithms for UEFI image verification, e.g. SHA256-RSA2048
General
* simplify printing short texts for GUIDs
* provide a unit test for printing GUIDs
This converts the following to Kconfig:
CONFIG_AT91_EFLASH
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Prepare migration to Kconfig.
CONFIG_SYS_MAX_FLASH_BANKS_DETECT becomes boolean and
CONFIG_SYS_MAX_FLASH_BANKS define the MAX size, also used
for detection when CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
(CFI_MAX_FLASH_BANKS = CONFIG_SYS_MAX_FLASH_BANKS).
CONFIG_SYS_MAX_FLASH_BANKS become mandatory when
CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Replace CONFIG_SYS_MAX_FLASH_BANKS by CFI_FLASH_BANKS to prepare
Kconfig migration and avoid to redefine CONFIG_SYS_MAX_FLASH_BANKS
in cfi_flash.h.
After this patch CONFIG_SYS_MAX_FLASH_BANKS should be never used in
the cfi code: use CFI_MAX_FLASH_BANKS for struct size or CFI_FLASH_BANKS
for number of CFI banks which can be dynamic.
This patch modify all the files which include mtd/cfi_flash.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
- meson64_android: define raw parts for bootloader to permit flashing with fastboot
- vim3: configure serial# from ethaddr to permit using fastboot like sei510/610
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmHpItEACgkQd9zb2sjI
SdFSzRAAzDm/1khR4MXSTLjzBOs3N1ydxeqj7NtYU4tkf+vBjr62iOHUBeHx+DUv
Z1WwOaBrQyinhPunrjCrTGfit/OgRqoDFgEiWUmctm/ZlxcG2fAklq2o7rL2jX1t
uDvqeOgqW6N4ZXDlP1EXXZeUDzyYey0CGQzilXPlKqFOLXpOLYn40xznyhV2Rxkt
l+R1LSGzMsPo4JVIMpfHRPseIBL0Ae7d23LT+M6FF/my0SZUjzuVzadhvNaBeIGb
l+dP8enEPo1SCNP9BY+MO5zX4zyjc9T6EdYD4wqaMp23m+gAr3qW8tSbAv2H1aMr
lsvalvHIGJWXyYGcWOIEfQwBYjFOdCpkIIDTg4GFwgmRKPAlBZrckatAl/TXbBJH
nbAu+aHV/0dlCRgrFtIi//pnz3Ge1JGXSG1M71zbaXEXOJlFriWfq9KZdZ0TmcsE
npHA9f4wlrWK9a8eRmNP7pbeXcDelFnIkVgxQfB2oyfEHSp/3EpKUkbF2EUVbK7G
FyN4VaY3X/zgs9D5NdIeOMsqurF4h/s/yEMhzdQzoe76vXhxwzFHfdJaiZ/Nw7U8
eL+SBvu9NqL1uMv/IrLVzSbKc0q01p1MlQvVYNumu1Wdt25brvcq4YNl8phS6weh
quCOwUwp5s/r42V6TcDlipqIcntL5H8XaLvVPTarTH7C30aj0Hk=
=tP9Y
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220120' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Disable CONFIG_NET_RANDOM_ETHADDR for android configs
- meson64_android: define raw parts for bootloader to permit flashing with fastboot
- vim3: configure serial# from ethaddr to permit using fastboot like sei510/610
This weak function is not used anymore, so completely remove it.
Private struct comphy_map is not used by any board code anymore, so move it
into private driver header file comphy_core.h.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
Function prototypes must not be guarded with ifdef tests. Doing so
prevents us from doing:
if (CONFIG_IS_ENABLED(FOO))
func();
as that results in a warning when CONFIG_FOO is not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This Synchronizes the Actions Semi S700 SoC DT changes from
commit "g58e1100fdc59" ("Linux v5.16-rc3").
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
The code is cross-ported from BLAKE2 reference implementation
(https://github.com/BLAKE2/BLAKE2).
With minimal change to remove unused macros/features.
Currently there is only one user inside U-boot (btrfs), and since it
only utilize BLAKE2B, all other favors are all removed.
Signed-off-by: Qu Wenruo <wqu@suse.com>
[trini: Rename ROUND to R to avoid clash with <linux/bitops.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Add a return value to kgdb_init and use it directly in the post-relocation
init sequence, rather than using a wrapper stub. Also, move the "KGDB"
print message inside kgdb_init().
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Commit 98f705c9ce ("powerpc: remove 4xx support") removed (in 2017) the
last code that made use of bedbug debugger support. Since there aren't
any boards left that define either CONFIG_CMD_BEDBUG or a real
bedbug_init(), drop this feature from u-boot.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
The am335x-ice-v2 board's Ethernet ports can be configured
in 'MII' or 'RMII' mode to be connected to 'PRUSS' or 'CPSW'
Ethernet subsystems.
This patch sets the environment variable 'ice_mii' to
'mii' or 'rmii' accordingly. Based on that we choose the
appropriate board devicetree i.e. 'am335x-ice-v2.dtb' or
'am335x-ice-v2-prueth.dtb'.
Since there are 2 Ethernet ports with 2 modes, there can be 4
configurations but for now we consider both ports in different modes
to be an invalid configuration and prevent boot in that case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Amjad: use overlay instead of using new am335x-ice-v2-prueth.dtb]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make prueth_is_mii be marked __maybe_unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
NXP's mEMAC reference manual, Chapter 6.5.5 "MDIO Ethernet Management
Interface usage", specifies to poll the BSY (0) bit in the CFG/STAT
register to wait until a transaction has finished, not bit 31 in the
data register.
In the Linux kernel, this has already been fixed in commit 26eee0210ad7
("net/fsl: fix a bug in xgmac_mdio").
This patch changes the register in the fman_mdio and fsl_ls_mdio
drivers.
As the MDIO_DATA_BSY define is no longer in use, this patch also removes
its definition from the fsl_memac header.
Signed-off-by: Markus Koch <markus@notsyncing.net>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
This driver is based on an older downstream TI kernel, with
changes and cleanups to work with mainline device-tree bindings.
Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Documentation:
* Fix building HTML documentation of readthedocs.io
* Add ARM Juno board documentation
* Build requirements for Alpine Linux
* Include DM headers in API documentation
UEFI:
* Fix section alignment of EFI binaries
* Fix header length of RISC-V EFI binaries allowing to run them on EDK II
* Remove kaslr-seed from device tree if the EFI_RNG_PROTOCOL is provided
Other:
* Let 'part list' show all 128 GPT partitions
-----BEGIN PGP SIGNATURE-----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=NZ+6
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1
Documentation:
* Fix building HTML documentation of readthedocs.io
* Add ARM Juno board documentation
* Build requirements for Alpine Linux
* Include DM headers in API documentation
UEFI:
* Fix section alignment of EFI binaries
* Fix header length of RISC-V EFI binaries allowing to run them on EDK II
* Remove kaslr-seed from device tree if the EFI_RNG_PROTOCOL is provided
Other:
* Let 'part list' show all 128 GPT partitions
Document the return value in efi_init(). Fix up @sizep in efi_info_get().
Use Return: instead of @return
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present the 'efi' command only works in the EFI payload. Update it to
work in the app too, so the memory map can be examined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present this function requires a pointer to struct efi_entry_memmap
but the only field used in there is the desc_size. We want to be able
to use it from the app, so update it to use desc_size directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this code is inline in the app and stub. But they do the same
thing. The difference is that the stub does it immediately and the app
doesn't want to do it until the end (when it boots a kernel) or not at
all, if returning to UEFI.
Move it into a function so it can be called as needed.
Add a comment showing how to store the memory map so that it can be
accessed within the app if needed, for debugging purposes only. The map
can change without notice.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot, in some occasions, injects a 'kaslr-seed' property on the /chosen
node. That would be problematic in case we want to measure the DTB we
install in the configuration table, since it would change across reboots.
The Linux kernel EFI-stub completely ignores it and only relies on
EFI_RNG_PROTOCOL for it's own randomness needs (i.e the randomization
of the physical placement of the kernel). In fact it (blindly) overwrites
the existing seed if the protocol is installed. However it still uses it
for randomizing it's virtual placement.
So let's get rid of it in the presence of the RNG protocol.
It's worth noting that TPMs also provide an RNG. So if we tweak our
EFI_RNG_PROTOCOL slightly and install the protocol when a TPM device
is present the 'kaslr-seed' property will always be removed, allowing
us to reliably measure our DTB.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
A GPT partition table typically has 128 entries. If a partition table
contains a partition 128 'part list' should be able to list it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/fdtaddr.h
and add the devfdt API to the HTML documentation;
these functions are NOT compatible with live tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/ofnode.h
and add the device tree node API to the HTML documentation;
the ofnode functions are compatible with Live tree or with flat
device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/read.h
and add the device read from device tree API to the HTML
documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/devres.h
and add the driver model device resource API, devres_*(),
to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/device.h
and add the driver model device API to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/platdata.h
and add the associated API to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/lists.h
and add the list API to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/devres.h
and add the associated driver model API to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct Sphinx style comments in include/dm/uclass.h
and add the driver model UCLASS API to the HTML documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
BOOT_TARGET_DEVICES should only be added if the corresponding u-boot
command is enabled otherwise the build will fail.
Signed-off-by: Piotr Kubik <piotr_kubik@vp.pl>
The function was missing from exports, even though it loooks like the
intent of the implementation in sscanf.c was to have it exported.
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Attempt to handle cases with a downstream port of a PCIe switch where
link training never completes and the link continues switching between
speeds indefinitely with the data link layer never reaching the active
state.
It has been observed with a downstream port of the ASMedia ASM2824 Gen 3
switch wired to the upstream port of the Pericom PI7C9X2G304 Gen 2
switch, using a Delock Riser Card PCI Express x1 > 2 x PCIe x1 device,
P/N 41433, wired to a SiFive HiFive Unmatched board. In this setup the
switches are supposed to negotiate the link speed of preferably 5.0GT/s,
falling back to 2.5GT/s.
However the link continues oscillating between the two speeds, at the
rate of 34-35 times per second, with link training reported repeatedly
active ~84% of the time, e.g.:
02:03.0 PCI bridge [0604]: ASMedia Technology Inc. ASM2824 PCIe Gen3 Packet Switch [1b21:2824] (rev 01) (prog-if 00 [Normal decode])
[...]
Bus: primary=02, secondary=05, subordinate=05, sec-latency=0
[...]
Capabilities: [80] Express (v2) Downstream Port (Slot+), MSI 00
[...]
LnkSta: Speed 5GT/s (downgraded), Width x1 (ok)
TrErr- Train+ SlotClk+ DLActive- BWMgmt+ ABWMgmt-
[...]
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis+, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
[...]
Forcibly limiting the target link speed to 2.5GT/s with the upstream
ASM2824 device makes the two switches communicate correctly however:
02:03.0 PCI bridge [0604]: ASMedia Technology Inc. ASM2824 PCIe Gen3 Packet Switch [1b21:2824] (rev 01) (prog-if 00 [Normal decode])
[...]
Bus: primary=02, secondary=05, subordinate=09, sec-latency=0
[...]
Capabilities: [80] Express (v2) Downstream Port (Slot+), MSI 00
[...]
LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
[...]
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis+, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
[...]
and then:
05:00.0 PCI bridge [0604]: Pericom Semiconductor PI7C9X2G304 EL/SL PCIe2 3-Port/4-Lane Packet Switch [12d8:2304] (rev 05) (prog-if 00 [Normal decode])
[...]
Bus: primary=05, secondary=06, subordinate=09, sec-latency=0
[...]
Capabilities: [c0] Express (v2) Upstream Port, MSI 00
[...]
LnkSta: Speed 2.5GT/s (downgraded), Width x1 (downgraded)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
[...]
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
[...]
Make use of this observation then and attempt to detect the inability to
negotiate the link speed automatically, and then handle it by hand. Use
the Data Link Layer Link Active status flag as the primary indicator of
successful link speed negotiation, but given that the flag is optional
by hardware to implement (the ASM2824 does have it though), resort to
checking for the mandatory Link Bandwidth Management Status flag showing
that the link speed or width has been changed in an attempt to correct
unreliable link operation (the ASM2824 does set it too).
If these checks indicate that link may not operate correctly, then poll
the Data Link Layer Link Active status flag along with the Link Training
flag for the duration of 200ms to see if the link has stabilised, that
is either that the Data Link Layer Link Active status flag has been set
or that Link Training has been inactive during at least the second half
of the interval.
If that has indicated failure, restrict the target speed to 2.5GT/s,
request a link retrain and check again if the link has stabilised. If
that does not work either, then restore the original speed setting and
claim defeat, otherwise we are done.
NB interestingly enough with the ASM2824 vs PI7C9X2G304 configuration
referred above asking the ASM2824 to retrain with a higher target link
speed once the 2.5GT/s speed has been negotiated makes the two devices
successfully negotiate 5.0GT/s. Lifting the 2.5GT/s speed restriction
would however prevent our workaround from working with an OS that issues
a reset and that is unaware of the problem. This is because the devices
would then try to negotiate a higher link speed from scratch and fail,
while the sticky property of the Target Link Speed setting will keep the
2.5GT/s speed restriction across a reset.
Keep the 2.5GT/s speed restriction then, conservatively, if functional
once applied.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
These hardcoded values were calculated from CONFIG_SPL_TEXT_BASE macro. Now
this macro is configurable via Kconfig, so calculate values 0x0030/0x4030
at compile time via CONFIG_SPL_TEXT_BASE option. Values 0x0030/0x4030
represents offset of CONFIG_SPL_TEXT_BASE from address 0x40000000.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Memory layout in the comment is from Armada XP platform which uses load
address 0x40004030. DB-88f6720 is Armada 375 platform which uses same load
address as Armada 38x which is 0x40000030.
Currently SPL support for Armada 375 is unfinished and does not work. There
is missing Serdes initialization and DDR3 training code. So nobody noticed
that CONFIG_SPL_* options are not correct.
Fix at least CONFIG_SPL_TEXT_BASE constant and remove incorrect comments
about memory layout. So it is not misleading.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This implementation is intended to be copied to other projects and
modified, to as to foster a standard means of communcating runtime
information between firmware projects.
The GPL-2 license is too restrictive for some projects, e.g. those
intended as reference implementations rather than designed for
collaborative open-source development.
Update the license to make this easier to share.
Signed-off-by: Simon Glass <sjg@chromium.org>
FIx up various minor errors and add the API documentation to the bloblist
docs, since it is quite useful to see it in the same place.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we do support allocating the bloblist but the Kconfig is a bit
strange, since we still have to specify an address in that case. Partly
this is because it is a pain to have CONFIG options that disappears when
its dependency is enabled. It means that we must have #ifdefs in the code,
either in the C code or header file.
Make use of IF_ENABLED_INT() and its friend to solve that problem, so we
can separate out the location of bloblist into a choice. Put the address
and size into variables so we can log the result.
Add the options for SPL as well, so we can use CONFIG_IS_ENABLED().
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if someone adds a tag in the middle of the list it works well
enough within a U-Boot build. But if these tags are used in another
project, or with an older version of SPL, the numbers make become
inconsistent.
Use explicit tag numbers that never change, to resolve this problem.
Allocate areas for existing U-Boot tags and set up an area for use by
projects and vendors, as well as for private use. Keep tags above
0x10000 unallocated for now.
Update bloblist_tag_name() and the tests to work with this new setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
The EC event log tag is no-longer used. The vboot handoff is now handled
by the vboot context instead.
Drop these unused tags.
Signed-off-by: Simon Glass <sjg@chromium.org>
It seems best to put the magic number right at the start of the bloblist
header, so it is easier to check. This is how devicetree works.
Make this change now, before other projects make use of bloblist. Other
changes may be needed / discussed, but that is TBD.
Add a checker function as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bright sparks have decided that a cast on a constant cannot be a
constant, so offsetof() produces this warning on clang-10:
include/intel_gnvs.h:113:1: error: static_assert expression is not an
integral constant expression
check_member(acpi_global_nvs, unused2, GNVS_CHROMEOS_ACPI_OFFSET);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/kernel.h:284:2: note: expanded from macro 'check_member'
offsetof(struct structure, member) == (offset), \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/stddef.h:20:32: note: expanded from macro 'offsetof'
^
include/intel_gnvs.h:113:1: note: cast that performs the conversions of
a reinterpret_cast is ot allowed in a constant expression
include/linux/stddef.h:20:33: note: expanded from macro 'offsetof'
Fix it by using the compiler built-in version, if available. This syncs
the function to the same implementation as Linux v5.16 in this header
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot define loff_t as long long. But the header
/usr/include/linux/types.h may not define it.
This has lead to a build error on Alpine Linux.
So let's use long long instead of loff_t for
the size parameter of function os_get_filesize().
Reported-by: Milan P. Stanić <mps@arvanta.net>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
PCI msc01 driver uses standard format of Config Address for PCI
Configuration Mechanism #1 but with cleared Enable bit.
So use new U-Boot macro PCI_CONF1_ADDRESS() with clearing PCI_CONF1_ENABLE
bit and remove old custom driver address macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
PCI gt64120 driver uses standard format of Config Address for PCI
Configuration Mechanism #1.
So use new U-Boot macro PCI_CONF1_ADDRESS() and remove old custom driver
address macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Lot of PCI and PCIe controllers are using standard Config Address for PCI
Configuration Mechanism #1 or its extended version.
So add PCI_CONF1_ADDRESS() and PCI_CONF1_EXT_ADDRESS() macros into U-Boot's
pci.h header file which can be suitable for most PCI and PCIe controller
drivers. Drivers do not have to invent their own macros and can use these
new U-Boot macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
We want to replace '#ifdef' by 'if (IS_ENABLED(CONFIG_...))' in our code.
Therefore functions should be defined unconditionally even if they are not
implemented.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[ fsl_esdhc commit 52faec3182 ]
Make the code cleaner and drop the old-style #ifdef constructs where it is
possible.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[ fsl_esdhc commit 5b05fc0310 ]
Voltage validation should be done by CMD8. Current comparison between
mmc_cfg voltages and host voltage capabilities is meaningless.
So drop current comparison and let voltage validation is through CMD8.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmHYV8MACgkQd9zb2sjI
SdELkA/+LjyjJB1KI6/KLLg43zyFeeZX/SjQd5BUIx6EfaCgyTkuq2lzQnErGmbi
HoyMoNLpBxLIL27/5TXPzmKYAeOfKPxA/sXTTtx/l7PG8ncSZIoU0+utqjycdUsK
tSi7EdFzk7/kDDRkqqA7q9nxsPn/7GQNh/ZC9zstMXKaTO/TEb/sZWCMcvQ0MNoB
ynZKOCg5t60UkIYIRwZwC/OS/ssn86dovv/Aa/8D6qpL2AbS5DoCXHuAr8Dnz7fJ
q4rV7oLh7a+WHe/qC7R6ylYFIVVqY5JaIgbLDwuvk1z9o7txchMMQnGgllZ35sN9
LECD2iSDGjhPaHuGCvQwl3TWtIpvtdcP4sQTyJhsXNPxCG6HHvRz7xY4erUohR1I
LIddwCCHeCrBiaamXNbCzph2+JhfPSQ5ETCL9M6iBMxNUPunlCxjfjDzlT/pg11p
EO9PIPjRMR9QhxKtd3gZpyAqPuMBEmIwhDtHI6dL3DNOOsF44ObE4swnzS6qXIDn
jRZzFCC2f/Vyg11YnzFtV3A5eWwJahGDWAGAnnlg6Y8GCLlLmDJitcgA/rWSALko
T5fC8L8IFUx2RnHczyitJ/wqJl9FqOAnIaoB3Trpwp8gFQ15dQjbvoXldQnAjSS2
9bns3zOrx79EF4lbHhwNE9UDLm6OjK5vR3h4bGJvyZBmasVsA90=
=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
After the conversion to DM the SD card shows up as 'mmc 2'
device.
Adjust the 'mmcdev' and the distro command 'func' accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Enable support for USB and USB storage on the UDOO Neo.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In AOSP, both VIM3 and VIM3L have 2 bootloader flavors,
depending on A/B enablement.
For example, for vim3l, the naming is:
- u-boot_kvim3l_noab.bin : legacy support
- u-boot_kvim3l_ab.bin : A/B support
Prepare a defconfig to support u-boot_kvim3_ab.bin and
u-boot_kvim3l_ab.bin.
This is identical to khadas-vim3{l}_ab_android but will be updated in
the next commit.
Also update partitioning tables for A/B support.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-4-mkorpershoek@baylibre.com
This allows us to define extra board variables, such as "board" and
"board_name".
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-2-mkorpershoek@baylibre.com
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-7-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze is one the last two users of the CONFIG_SYS_RESET_ADDRESS
macro (the other is arch/powerpc/cpu/mpc8xx/cpu.c, but the macro is not
defined anywhere in powerpc code, so it should be removed there too).
Replace CONFIG_SYS_RESET_ADDRESS usage in start.S with
CONFIG_SYS_TEXT_BASE. If the reset address should really be
user-configurable, a new Kconfig option could be added.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-6-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The memory layout is taken from the device tree passed to us by
m1n1, so there is no need to define this.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The SMSC driver is using the old driver model.
Init the virtio system in vexpress64.c so that the network device is
discovered.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Move env var address values to #defines so they can be reused elsewhere.
Rename env var names to those recommended in the README and modify
addresses to allow more space for the kernel.
Fix issue where fdt is called with invalid arguments when booting
without a ramdisk.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Rename from vexpress_aemv8a.h -> vepxress_aemv8.h as new FVPs may not be
v8-A. No change in behavior.
This is towards future work to enable support for the FVP_BaseR.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
When using a recent kernel with a bunch of compiled-in
stuff the kernel image easily becomes bigger than 8 MB
yielding this error:
Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Fix this by bumping to SZ_64MB.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
-----BEGIN PGP SIGNATURE-----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=YdSB
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request of efi-next
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
This provides access to EFI tables after U-Boot has exited boot services.
It is not needed in the app since boot services remain alive and we can
just call them whenever needed.
Add a comment to explain this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present each of these has its own static variable and helper functions.
Move them into a shared file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This should return false when the EFI app is running, since UEFI has done
the required low-level init. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When starting the app, locate all block devices and make them available
to U-Boot. This allows listing partitions and accessing files in
filesystems.
EFI also has the concept of 'disks', meaning boot media. For now, this
is not obviously useful in U-Boot, but add code to at least locate these.
This can be expanded later as needed.
We cannot use printf() in the early stub or app since it is not compiled
in
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently we allow and explicitly check a single shared page with
StandAloneMM. This is dictated by OP-TEE which runs the application.
However there's no way for us dynamically discover the number of pages we
are allowed to use. Since writing big EFI signature list variable
requires more than a page, OP-TEE has bumped the number of shared pages to
four.
Let's remove our explicit check and allow the request to reach OP-TEE even
if it's bigger than what it supports. There's no need to sanitize the
number of pages internally. OP-TEE will fail if we try to write more
than it's allowed. The error will just trigger later on, during the
StMM access.
While at it add an error message to help users figure out what failed.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Ilias Apalodimas <apalos@gmail.com>
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
UEFI:
* allow for more than 16 KiB UEFI variable size when using StMM
Others:
* make watchdog sysreset compatible with separate poweroff driver
* avoid OpenSSL deprecation warnings
-----BEGIN PGP SIGNATURE-----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=VFOg
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-01-rc4-4' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-01-rc4-4
UEFI:
* allow for more than 16 KiB UEFI variable size when using StMM
Others:
* make watchdog sysreset compatible with separate poweroff driver
* avoid OpenSSL deprecation warnings
This converts the following to Kconfig:
CONFIG_JFFS2_DEV
CONFIG_JFFS2_LZO
CONFIG_JFFS2_NAND
CONFIG_JFFS2_PART_OFFSET
CONFIG_JFFS2_PART_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_88F5182
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_IS_OPENRD_CLIENT
CONFIG_BOARD_IS_OPENRD_ULTIMATE
CONFIG_D2NET_V2
CONFIG_FEROCEON
CONFIG_FEROCEON_88FR131
CONFIG_INETSPACE_V2
CONFIG_KW88F6192
CONFIG_KW88F6281
CONFIG_KW88F6702
CONFIG_NET2BIG_V2
CONFIG_NETSPACE_LITE_V2
CONFIG_NETSPACE_MAX_V2
CONFIG_NETSPACE_MINI_V2
CONFIG_NETSPACE_V2
CONFIG_SHEEVA_88SV131
At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.
Signed-off-by: Tom Rini <trini@konsulko.com>
The only place we use CONFIG_CPU_ARMV8 was in the arm_dcc serial driver.
Switch this to CONFIG_ARM64 today, and if in the future we need finer
granularity tuning here, a new CONFIG_SERIAL option needs to be
introduced.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one of two ways. The first way is that it
is defined to a static value, of an unsigned long size. The second way
is that it is defined to something, typically a function, to determine
this value at run time.
However, in a few cases that function returns a static value. Change
that to using the static value directly.
In the case of using something at run time, convert everything to using
a function of the same name and prototype. This will allow for further
cleanups.
Finally, we have a few cases where the function is just not used, so
drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_CLK_FREQ_C100 and CONFIG_SYS_CLK_FREQ_C110 are
only used in one place and not changed by the board config file. Move
these out of the CONFIG namespace and in to the CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish this conversion we need to add a symbols for
SPL_SYS_NAND_SELF_INIT and TPL_SYS_NAND_SELF_INIT as there are cases
there where we need to, or need to not, use that framework as things
stand.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of CONFIG_SYS_FDT_ADDR this was being used to modify the
default value of fdt_addr / fdt_addr_r, which is not something to expose
in this manner and is not otherwise done. The case of SYS_ENV_ADDR is
similar but only done on the pic32mzdask platform, for scriptaddr.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
This is removing unused defines and correcting the default value to be
0x0 as we are a hex symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.
For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.
For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
In order to do this conversion, expose this option to the user and
use "save" not "safe" in the text.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_RPMB
This fixes a few platforms where the option was not taking effect as
intended.
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used as part of configuring the default environment for a
number of platforms. However, it is always set to 1 and the only time
it is part of Kconfig, it is used in a hard-coded manner. Hard-code the
value in the environment instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
Show the U-Boot logo by default. This is only 7KB in size so seems like
a useful default for boards that enable a display.
If SPLASH_SCREEN is enabled, it is not enabled by default, so as not to
conflict with that feature.
Also disable it for tests, since we don't want to complicate the output.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_VIDEO_LOGO
Note that this option depends on CONFIG_DM_VIDEO now, since cfb_console is
deprecated. The only relevant code is now in splash.c
Drop the check for DM_VIDEO in that file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently we allow and explicitly check a single shared page with
StandAloneMM. This is dictated by OP-TEE which runs the application.
However there's no way for us dynamically discover the number of pages we
are allowed to use. Since writing big EFI signature list variable
requires more than a page, OP-TEE has bumped the number of shared pages to
four.
Let's remove our explicit check and allow the request to reach OP-TEE even
if it's bigger than what it supports. There's no need to sanitize the
number of pages internally. OP-TEE will fail if we try to write more
than it's allowed. The error will just trigger later on, during the
StMM access.
While at it add an error message to help users figure out what failed.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Ilias Apalodimas <apalos@gmail.com>
Enable SPL support in Kconfig and add some related option in
rk3568_common.h
Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com>
Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
At present this override function is called even when OF_BOARD is not
enabled. This makes it impossible to disable this feature and in fact
makes the OF_BOARD option useless.
Reinstate its intended purpose, so that it is possible to switch between
the appended devicetree and one provided by the board's custom function.
A follower patch adds warnings for this scenario, but for now we don't
have a Kconfig that definitively tells us that OF_BOARD should be used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sync these files, obtained from Linux v5.15.
This adds a devicetree file for rpi_4 which was not there before.
Testing shows no change so far as I can see:
- boots to U-Boot prompt on rpi0, rpi2
- boots to distro on rpi3
- boots to distro on rpi4
I am assuming that syncing with Linux is safe, but the maintainer should
know for sure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move Turris MOX specific remove_disabled_nodes() to fdt_support with
name fdt_delete_disabled_nodes(), so that others can potentially use it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add functions
fdt_node_offset_by_pathf(),
fdt_create_phandle_by_pathf(),
fdt_set_status_by_pathf()
to get node offset, get/create node phandle and set status for node
given by path/alias formatted with sprintf.
Add functions
fdt_create_phandle_by_compatible(),
fdt_set_status_by_compatible()
to get/create node phandle and set status for first node given by
compatible.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit f0921f5098 ("fdt: Sync up to the latest libfdt") introduced
fdt_generate_phandle() in libfdt, making fdt_alloc_phandle() obsolete in
fdt_support.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: "hui.song" <hui.song_1@nxp.com>
Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The macro __constant_cpu_to_be32() uses ___constant_swab32(), which for
some reason is not defined and causes the following error during
compilation:
include/linux/byteorder/little_endian.h:28:52: warning:
implicit declaration of function ‘___constant_swab32’;
did you mean ‘__builtin_bswap32’? [-Wimplicit-function-declaration]
#define __constant_cpu_to_be32(x) ((__force __be32)___constant_swab32((x)))
Declare all ___constant_swabXX() macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Due to a non-existing parameter name in macro's, use of those macro's will
cause a compiler error of "undefined reference".
Unfortunately, dm test doesn't fail because a wrong name ("&dev", hence it
is accidentally a valid name in the context of a caller site) is passed on.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Fixes: f262d4ca4b ("dm: core: Add a way to read platdata for all
child devices")
Fixes: 903e83ee84 ("dm: core: Add a way to iterate through children,
probing each")
Reviewed-by: Simon Glass <sjg@chromium.org>
This function will be commonly used in block device drivers
in the succeeding patches.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In strange cases it is possible for fdtgrep to find nothing to output.
Typically this means that the resulting SPL device tree is not going to
allow anything to boot, but at present the tree is actually invalid,
since it only has an END tag in the struct region.
The FDT spec requires at least a root node. So add a special case to
include at least this, if the FDT_REG_SUPERNODES flag is set.
This ensures that grepping an empty tree still produces a valid tree.
Also add comments to the enum since it is not completely obvious from
the names now.
The typical symptom of this problem is a message from binman:
pylibfdt error -11: FDT_ERR_BADSTRUCTURE
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds better logging support for many CCF drivers, and clarifies some
documentation regarding clk_get_rate.
-----BEGIN PGP SIGNATURE-----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=1L3q
-----END PGP SIGNATURE-----
Merge tag 'clk-2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-clk
Clock patches for v2022.01-rc3
This adds better logging support for many CCF drivers, and clarifies some
documentation regarding clk_get_rate.
Improve clk_get_rate() @return documentation that otherwise is a bit
ambiguous. At the moment I expect to return 0 as error since the return
type is 'ulong', instead the function really returns negative value in
case the corresponding function pointer is null and returns 0 if the clock
is invalid.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The resync of the device trees from Linux 5.16-rc3 caused aliases
to appear on the MMC devices which changed the numbering.
This changed the default boot device and caused boot failure.
Update the mmcdev variable to reflect the new aliases.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add a block driver which handles read/write for EFI block devices. This
driver actually already exists ('efi_block') but is not really suitable
for use as a real U-Boot driver:
- The operations do not provide a udevice
- The code is designed for running as part of EFI loader, so uses
EFI_PRINT() and EFI_CALL().
- The bind method probes the device, which is not permitted
- It uses 'EFI' as its parent device
The new driver is more 'normal', just requiring its platform data be set
up in advance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
UCLASS_EFI_LOADER is used for devices created by applications and
drivers loaded by U-Boots UEFI implementation.
This patch provides a new uclass (UCLASS_EFI_MEDIA) to be used for devices
that provided by a UEFI firmware calling U-Boot as an EFI application.
If the two uclasses can be unified, is left to future redesign.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
These names are better used for access to devices provided by an EFI
layer. Use EFI_LOADER instead here, since these are only available in
U-Boot's EFI_LOADER layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This commit modify efi_tcg2_register() to return the
appropriate error.
With this fix, sandbox will not boot because efi_tcg2_register()
fails due to some missing feature in GetCapabilities.
So disable sandbox if EFI_TCG2_PROTOCOL is enabled.
UEFI secure boot variable measurement is not directly related
to TCG2 protocol installation, tcg2_measure_secure_boot_variable()
is moved to the separate function.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CONFIG_SYS_ATA_PORT_ADDR is not used in the code anymore. Drop it and use
ATA_PORT_ADDR() locally instead.
Drop CONFIG_IDE_RESET_ROUTINE and CONFIG_IDE_SWAP_IO which are also
unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used by sandbox since it uses driver model for the timer.
Drop it.
Also update the tools_only build to avoid build errors, since it does
actually build U-Boot too. Enable DM so we can use CONFIG_TIMER,
disable EFI_LOADER to avoid an error about board_quiesce_devices() and
disable NET to avoid having to define CONFIG_AVB_BUF_ADDR
Signed-off-by: Simon Glass <sjg@chromium.org>
This can go in the related header file. Drop the CONFIG option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The device tree split into .dtsi and .dts files, common
device node for eMMC/SD, enable I2C1, UART1 for console
instead of UART0, enable the DDR 2GB memory and in
that 288MB memory is reserved for fabric buffer.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add boot command "bootcmd_ram" to support autoboot from RAM.
This feature could be useful at the very initial state of chip design
when there is only a minimal set of peripheral. (e.g. without mmc and mac ..etc)
The kernel image is default to be loaded at 0x2000000 via debug port,
and the following script serves as an example:
spl()
{
cmd="riscv64-linux-gdb -q \
-ex \"target remote $host:$port\" \
-ex \"load\" \
-ex \"thread apply all set \\\$pc=&_start\" \
-ex \"thread apply all set \\\$a0=\\\$mhartid\" \
-ex \"thread apply all set \\\$a1=<dtb address>\" \
-ex \"restore u-boot.itb binary 0x200000\" \
-ex \"restore Image binary 0x2000000\" \
-ex \"c\" \
spl/u-boot-spl
"
echo $cmd
eval $cmd
}
The address where the kernel is loaded can be altered by
changing the value of KERNEL_IMAGE_ADDR.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Broadcom bnxt L2 driver support. Used by the Broadcom
iproc platforms.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Use the return value ENOSYS for unsupported API
- pinctrl_generic_set_state
- pinctrl_select_state
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM
This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a new function to activate an existing simple frame buffer node
and add the associated reserved memory, with no-map properties.
This device tree update is only done when the video device is active
and the video buffer is used.
This patch uses '#if CONFIG_IS_ENABLED(DM_VIDEO)' because
gd->video_bottom and gd->video_top are only defined when CONFIG_DM_VIDEO
is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the helper function video_is_active() to test if one video device
is active.
This function can be used in board code to execute operation
only when the display is probed / really used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the function named lcd_dt_simplefb* to fdt_simplefb* to be aligned
with the associated file name fdt_simplefb.h/fdt_simplefb.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
This converts the following to Kconfig:
CONFIG_LCD_DT_SIMPLEFB
This patch also renames this config to CONFIG_FDT_SIMPLEFB as the code in
common/lcd_simplefb.c support CONFIG_LCD and CONFIG_VIDEO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Using mmc.dtbo from rpi-firmware to switch the controller for the SD
card slot from sdhci to sdhost causes the numbering to change; the
SD card is then not recognized at boot. Add to the range checked.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The current tpm2_pcr_read is hardcoded using SHA256. Make the
actual command to TPM configurable to use wider range of algorithms.
The current command line is kept as is i.e limited to SHA-256 only.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Platforms may have support to measure their initial firmware components
and pass the event log to u-boot. The event log address can be passed
in property tpm_event_log_addr and tpm_event_log_size of the tpm node.
Platforms may choose their own specific mechanism to do so. A weak
function is added to check if even log has been passed to u-boot
from earlier firmware components. If available, the eventlog is parsed
to check for its correctness and further event logs are appended to the
passed log.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a function that returns the number of devices in a uclass. This can be
helpful in sizing an array that needs to hold a list of them.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it is useful to search just by a partial name, such as
when looking for a sibling device that has a common name substring. Add
helper functions to handle these requirements.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support reading a string list a string at a time. Apart
from being inefficient, this makes it impossible to separate reading of
the devicetree into the of_to_plat() method where it belongs, since any
code which needs access to the string must read it from the devicetree.
Add a function which returns the string property as an array of pointers
to the strings, which is easily used by clients.
Signed-off-by: Simon Glass <sjg@chromium.org>
The details for of_property_read_string_helper() and
ofnode_read_string_index() are a little inaccurate. Fix up the comments to
avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
This method is currently called after the platform data has been freed.
But the pre_unbind() method may wish to access this, e.g. to free some
data structures stored there.
Split the unbinding of devices into two pieces, as is done with removal.
This corrects the problem.
Also tidy a code-style issue in device_remove() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This text should never change during execution, so it makes sense to
use a const char * so that it can be declared as const in the code.
Update struct cmd_tbl with a const char * pointer for 'help'.
We cannot make usage const because of the bmode command, used on mx53ppd
for example.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Adds TEE_ERROR_SHORT_BUFFER as TEE error code. This error code is
commonly used by TEEs to inform caller that the buffer(s) it provided
is too small for the desired operation.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Define identifiers for clnt_login field in struct tee_open_session_arg
based in GlobalPlatform Device TEE IDs and on the REE_KERNEL identifier
extension from OP-TEE OS.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Correct inline comment describing API function devm_scmi_process_msg().
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Certain serial SERDES protocols like 1000base-x, 2500base-x, SGMII,
USXGMII can operate either in a mode where the PHY (be it on-board or
inside an SFP module) passes the link parameters (speed, duplex, pause)
to the MAC through in-band through control words standardized by IEEE
802.3 clause 37, or in a mode where the MAC must configure (force) its
link parameters based on information obtained out-of-band (MDIO reads,
guesswork etc).
In Linux, the OF node property named "managed" is parsed by the phylink
framework, and the convention is that if a driver uses phylink, then the
presence of this property means that in-band autoneg should be enabled,
otherwise it shouldn't.
To be compatible with the OF node bindings of drivers that use phylink
in Linux, introduce parsing support for this property in U-Boot too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In the current DSA switch driver API, only the udevice of the switch
(belonging to UCLASS_DSA) is exposed, as well as an "int port" argument.
So drivers do not have access to the udevice of individual ports
(belonging to UCLASS_ETH), one of the reasons being that not all ports
have an associated UCLASS_ETH udevice.
However, all DSA ports have an OF node, and in some cases the driver
needs a handle to it, for all ports including the CPU port. Example: the
following Linux per-port device tree property:
managed = "in-band-status";
states whether a port should operate with clause 37 in-band autoneg
enabled or not.
This patch exposes a function which can be called by individual drivers
as needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This is needed for the VLAN header structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Freescale TSEC can be a DSA master, and the ports of the attached
DSA switch can have different MAC addresses compared to the TSEC.
Nonetheless, the TSEC must receive the packets on behalf of those switch
ports. Therefore, implement the promiscuous mode method to allow DSA to
set this.
Note that the init_registers() function called from eth_ops :: start
overwrites this setting. There is no reason why the RCTRL register
should be zero-initialized, so just stop clearing it so that the setting
we applied in eth_ops :: set_promisc sticks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We have implemented all what is new in UEFI specification 2.9 and relevant
for U-Boot.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Implement the EFI_EVENT_GROUP_BEFORE_EXIT_BOOT_SERVICES event group
handling.
Add the definition of EFI_EVENT_GROUP_AFTER_READY_TO_BOOT.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This commit adds the comment for efi_system_table and
efi_configuration_table structure.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The extern keyword is not needed in include/lmb.h to declare functions.
Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Correct Sphinx style comments in include/lmb.h
Add the logical memory block API to the HTML documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Defining static functions in includes should be avoided.
Function lmb_is_nomap() is only used in the unit test.
So move it to the unit test.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If bootloader was updated without running oem format, reboot will cause
boot loop because the SYSTEM stage fails.
Add a final PANIC stage running fastboot to permit recovery.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This can lead to GPT and BCB errors even if fastboot was selected early
by usb rom boot and the eMMC is blank/invalid.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
AST2600 leverages the FIT hash/signature verification to fulfill
secure boot trust chain. To improve the performance and save SW
code size for those crypto operations, the two HW crypto engine,
HACE and ACRY, are enabled.
However, both of the engines can only access to data stored in
DRAM space. Therefore, we need to move the FIT image into DRAM
before the booting.
This patch update the CONFIG_BOOTCOMMAND to execute the pre-defined
ENV variable which consists of FIT image copy to memory and booting.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Lot of PCIe controllers are using ECAM addressing. So add common ECAM
macros into U-Boot's pci.h header file which can be suitable for most
PCI controller drivers.
Replace custom ECAM address macros in every PCI controller driver by new
ECAM macros from U-Boot's pci.h header file.
Similar macros are defined also in Linux kernel. There is a small
difference between Linux and these new U-Boot macros.
U-Boot's PCIE_ECAM_OFFSET() takes device and function numbers in separate
arguments. Linux's PCIE_ECAM_OFFSET() takes device and function numbers
encoded in one argument. The reason is that U-Boot's PCI_DEVFN() macro is
different than Linux's PCI_SLOT() macro. So having device and function
numbers in separate arguments makes code more straightforward.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This has different semantics in different places. Go with the bootm method
and put it in a common function so that the behaviour is consistent in
U-Boot. Update the docs.
To be clear, this changes the way that 'bootelf' and standalone boot
work. Before, if autostart was set to "fred" or "YES", for example, they
would consider that a "yes". This may change behaviour for some boards,
but the only in-tree boards which mention autostart use "no" to disable
it, which will still work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Wolfgang Denk <wd@denx.de>
Use a text file for the environment instead of the #define settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
At present U-Boot environment variables, and thus scripts, are defined
by CONFIG_EXTRA_ENV_SETTINGS. It is painful to add large amounts of text
to this file and dealing with quoting and newlines is harder than it
should be. It would be better if we could just type the script into a
text file and have it included by U-Boot.
Add a feature that brings in a .env file associated with the board
config, if present. To use it, create a file in a board/<vendor>
directory, typically called <board>.env and controlled by the
CONFIG_ENV_SOURCE_FILE option.
The environment variables should be of the form "var=value". Values can
extend to multiple lines. See the README under 'Environment Variables:'
for more information and an example.
In many cases environment variables need access to the U-Boot CONFIG
variables to select different options. Enable this so that the environment
scripts can be as useful as the ones currently in the board config files.
This uses the C preprocessor, means that comments can be included in the
environment using /* ... */
Also support += to allow variables to be appended to. This is needed when
using the preprocessor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Marek Behún <marek.behun@nic.cz>
This is a complicated set of #defines and it is painful to convert to a
text file. We can (once pending patches are applied) provide the same
functionality with bootmethod. Drop this for sandbox to allow conversion
to a text-file environment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Compiler is not happy:
common/image-board.c: In function ‘boot_get_kbd’:
common/image-board.c:902:17: warning: implicit declaration of function ‘do_bdinfo’ [-Wimplicit-function-declaration]
902 | do_bdinfo(NULL, 0, 0, NULL);
| ^~~~~~~~~
Move the forward declaration to a header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix dfu_alt_info to use nor1 instead of the device name.
This reverts a part of commit 59bd18d4c4 ("configs: synquacer:
Remove mtdparts settings and update DFU setting") because the
commit a4f2d83414 ("mtd: spi: nor: force mtd name to "nor%d"")
changed the mtd device naming scheme to nor%d.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This symbol has been functionally dead for a long time. Remove the last
and recent re-introductions of setting it, and update the whitelist so
it will not be re-introduced again.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_TRACE
CONFIG_TRACE_BUFFER_SIZE
CONFIG_TRACE_EARLY
CONFIG_TRACE_EARLY_ADDR
CONFIG_TRACE_EARLY_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH
CONFIG_ENV_IS_NOWHERE
CONFIG_ENV_OFFSET
CONFIG_ENV_OVERWRITE
CONFIG_ENV_SECT_SIZE
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Signed-off-by: Tom Rini <trini@konsulko.com>
The last board that used to set CONFIG_LYNXKDI has been removed in
commit 242836a893 ("powerpc: ppc4xx: remove pcs440ep support"),
doc/README.lynxkdi only talks about a MPC8260 board being supported,
and the mpc8260 support has been removed four years ago in commit
2eb48ff7a2 ("powerpc, 8260: remove support for mpc8260") already,
and common/lynxkdi.c only consists of an "#error" statement these
days, so it seems like the LYNX KDI code is dead code nowadays.
Let's remove it now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Refactor this code so that we can call the 'pxe get' command without going
through the command-line interpreter. This makes it easier to get the
information we need, without going through environment variables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
It is pretty strange that the pxe code uses the 'filesize' environment
variable find the size of a file it has just read.
Partly this is because it uses the command-line interpreter to parse its
request to load the file.
As a first step towards unwinding this, return it directly from the
getfile() function. This makes the code a bit longer, for now, but will be
cleaned up in future patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add an xtoa() function, similar to itoa() but for hex instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
