MCU timer1 is used as the tick timer for MCU R5 SPL, and the
clock-frequency defined in DT appears to be incorrect at the moment.
Actual clock source for the timer is MCU_SYSCLK0 / 4 which is 250MHz.
Earlier setup of 25MHz went unnoticed, as there was a separate issue
with omap-timer, which caused an error to the clock by a factor of 8
with j7 devices. This problem surfaced once the omap-timer was fixed.
Signed-off-by: Tero Kristo <kristo@kernel.org>
Force the clk-k3 driver to probe early during R5 SPL boot to ensure the
default system clock configuration is completed. Many other drivers
assume a default state of the clock tree and it is currently possible
for them to probe before clk-k3 depending on the exact system
configuration.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Copy the contents of the board config loaded from sysfw.itb into an
EXTBOOT shared memory buffer that gets passed to sciserver. This only
needs to be done if EXTBOOT area has not been populated by ROM code yet.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Only start-up the non-linux remote cores if we are running in legacy
boot mode. HSM rearch is not yet supporting this.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
If the raw PM support is built in, we are operating in the split
firmware approach mode where PM support is not available. In this
case, skip the board config for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add callback routines for parsing the firmware info from FIT image, and
use the data to boot up ATF and the MCU R5 firmware.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add platform clock and powerdomain data for J721e and J7200. This data
is used by the corresponding drivers to register all the required device
clocks and powerdomains.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add DM (device manager) firmware image to the fit image that is loaded by
R5 SPL. This is needed with the HSM rearch where the firmware allocation
has been changed slightly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
board_fit_image_post_process() passes only start and size of the image,
but type of the image is not passed. So pass fit and node_offset, to
derive information about image to be processed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
On J7 family of SoCs (J721E and J7200), sysfw is being split to be run
under two cores, TIFS portion on DMSC core, and DM firmware under MCU
R5. As MCU R5 is also used to run one phase of the bootloader, we must
prevent access from here towards sysfw services. To support this, add
new config option which can be used to detect presence of RM/PM sysfw
services.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].
[1] https://github.com/Xilinx/embeddedsw
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add nodes for SPI NOR partitions to the device tree of Turris MOX, as
are in Linux' device tree.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add nodes for indicator LED and reset button so that board code can
implement board factory reset mechanism.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There have been some changes to the am335x-<board> DTs related to the
rtc node, so let's re-syncs them with Linux.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-7-dariobin@libero.it
For USB DFU boot mode there is a limitation on the load address of boot
images that they have to be less than 0x70001000. Therefore, move the
SPL_TEXT_BASE address to 0x70000000.
Currently ATF is being loaded at 0x70000000, if the SPL is being loaded at
0x70000000 then ATF would overwrite SPL image when loaded. Therefore, move
the location of ATF to a latter location in SRAM, past the SPL image. Also
rearrange the EEPROM and BSS data on top of ATF.
Given below is the placement of various data sections in SRAM
┌──────────────────────────────────────┐0x70000000
│ │
│ │
│ │
│ SPL IMAGE (Max size 1.5 MB) │
│ │
│ │
│ │
├──────────────────────────────────────┤0x7017FFFF
│ │
│ SPL STACK │
│ │
├──────────────────────────────────────┤0x70192727
│ GLOBAL DATA(216 B) │
├──────────────────────────────────────┤0x701927FF
│ │
│ INITIAL HEAP (32 KB) │
│ │
├──────────────────────────────────────┤0x7019A7FF
│ │
│ BSS (20 KB) │
├──────────────────────────────────────┤0x7019F7FF
│ EEPROM DATA (2 KB) │
├──────────────────────────────────────┤0x7019FFFF
│ │
│ │
│ ATF (123 KB) │
│ │
│ │
├──────────────────────────────────────┤0x701BEBFB
│ BOOT PARAMETER INDEX TABLE (5124 B)│
├──────────────────────────────────────┤0x701BFFFF
│ │
│SYSFW FIREWALLED DUE TO A BUG (128 KB)│
│ │
├──────────────────────────────────────┤0x701DFFFF
│ │
│ DMSC CODE AREA (128 KB) │
│ │
└──────────────────────────────────────┘0x701FFFFF
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-9-a-govindraju@ti.com
AM64 EVM board has a micro USB 2.0 AB connector and the USB0_VBUS is
connected with a resistor divider in between. USB0_DRVVBUS pin is muxed
between USB0_DRVVBUS and GPIO1_79 signals.
Add the corresponding properties and set the pinmux mode for USB subsystem
in the evm dts file.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-7-a-govindraju@ti.com
U-Boot either supports USB host or device mode for a node at a time in the
device tree nodes. To support both host and dfu bootmodes, dr_mode is set
to "peripheral" by default and then fixed based on the mode selected by
the boot mode config dip switches on the board.
This needs to happen before the cdns3 generic layer binds the usb device
to a host or a device driver. Therefore, use fdtdec_setup_board()
implementation to fixup the device tree property.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-4-a-govindraju@ti.com
Add support for providing ATF load address with a Kconfig symbol.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-2-a-govindraju@ti.com
Update the ddr settings to use the DDR reg config tool rev 0.5.0.
This enables 2666MTs LPDDR configuration on J7200.
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210603131453.11414-1-praneeth@ti.com
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
macro, which expands the value provided to the Hz range without taking into
account the precise Hz setting. This causes the frequency of 266 MHz not ot
be found in the imx8mm_fracpll_tbl, since it is entered there with a
precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
fracpll frequency cannot be determined.
Correct the value in imx8mm_fracpll_tbl to match the one expanded by
MHZ(266) macro, rounding it down to MHz range only.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.
Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.
Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Clock initialization functionality has ambitious debug messages, which are
printed out when failures are triggered during execution:
- Separate frequency table lookup functions have the the same output that
makes it impossible to understand which function failed and produced the
output
- PLL decoding routine has a generic debug statement printed, which does
not state the actual value failed to be found
Extend the output for both cases with prefixing table lookup functions
output with function name, and report the failed value in PLL decoding
routine.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
A simple prototyping board with one microSD port, one Ethernet port,
2 USB ports, I2C, SPI, GPIO, and UART interfaces.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
We need those macros to instruct drivers on how to behave for SoC specific
quirks, so let's add it as done for other i.MX SoCs.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
At the moment a lot of u-boot,dm-spl properties are present in board .dts
file but this is not correct since u-boot,dm-spl property is u-boot
specific and must be listed into the separate imrt1020-evk-u-boot.dtsi
file. So let's move every u-boot,dm-spl property present in
imxrt1020-evk.dts to imxrt1020-evk-u-boot.dtsi file.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
At the moment a lot of u-boot,dm-spl properties are present in board .dts
file but this is not correct since u-boot,dm-spl property is u-boot
specific and must be listed into the separate imrt1050-evk-u-boot.dtsi
file. So let's move every u-boot,dm-spl property present in
imxrt1050-evk.dts to imxrt1050-evk-u-boot.dtsi file.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Lcdif needs both "pix" and "axi" clocks to be enabled so let's add them to
lcdif node.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Since we assume pll5 is the default lcdif clock source let's move
assigned-clocks(-parents) properties to .dtsi file.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Now device_type = "memory" is mandatory to allow u-boot to read memory
node, so let's add it to memory node.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Now device_type = "memory" is mandatory to allow u-boot to read memory
node, so let's add it to memory node.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
This mpu handling works for every i.MXRT SoC that we have, so let's
generalize imxrt1050_region_config to imxrt_region_config.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
No more map the reserved region with "no-map" property by marking
the corresponding TLB entries with invalid entry (=0) to avoid
speculative access.
The device tree parsing done in lmb_init_and_reserve() takes a
long time when it is executed without data cache, so it is called in
enable_caches() before to disable it.
This patch fixes an issue where predictive read access on secure DDR
OP-TEE reserved area are caught by firewall.
Series-cc: marex
Series-cc: pch
Series-cc: marek.bykowski@gmail.com
Series-cc: Ard Biesheuvel <ardb@kernel.org>
Series-cc: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add 8M for the U-Boot reserved memory (display, fdt, gd, ...)
mapped cacheable before relocation.
Without this patch the device tree, located before the MALLOC area
is not tagged cacheable just after relocation, before mmu reconfiguration.
This patch reduces the duration for device tree parsing in
lmb_init_and_reserve.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This reverts commit 786f888b74.
Looks like the datasheet at
https://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D3-Series-Data-sheet-DS60001609b.pdf
is wrong, and the testing was poorly done, because the PMECC did not raise
any error, but also didn't correct any bitflips. Restoring the offsets
as they were before, makes the PMECC on sama5d3x capable of correcting
bitflips.
Fixes: 786f888b74 ("sama5d3: Fix Galois Field Table offsets")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
os_find_text_base() assumes that first line of /proc/self/maps holds
information about the text. Hence we must call the function before calling
os_malloc() which calls mmap(0x10000000,).
Failure to do so has led to incorrect values for pc_reloc when an
exception was reported
=> exception undefined
Illegal instruction
pc = 0x5628d82e9d3c, pc_reloc = 0x5628c82e9d3c
as well as incorrect output of the bdinfo command
=> bdinfo
relocaddr = 0x0000000007858000
reloc off = 0x0000000010000000
Fixes: b308d9fd18 ("sandbox: Avoid using malloc() for system state")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
For some configurations with more PCIe cards and PCIe bridges, 16 MiB of
PCIe MEM space may not be enough. Since TF-A already allocates a 128 MiB
CPU window for PCIe, and since IO port space is only 64 KiB in total,
use all the remaining space (64 + 32 + 16 + 8 + 4 + 2 + 1 = 127 MiB) for
PCIe MEM.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Current version of this function uses a lot of incorrect assumptions about
the `ranges` DT property:
* parent(#address-cells) == 2
* #size-cells == 2
* number of entries == 2
* address size of first entry == 0x1000000
* second child address entry == base + 0x1000000
Trying to increase PCIe MEM space to more than 16 MiB leads to an overlap
with PCIe IO space, and trying to define additional MEM space (as a third
entry in the `ranges` DT property) causes U-Boot to crash when booting the
kernel.
## Flattened Device Tree blob at 04f00000
Booting using the fdt blob at 0x4f00000
Loading Device Tree to 000000001fb01000, end 000000001fb08f12 ... OK
ERROR: board-specific fdt fixup failed: <unknown error>
- must RESET the board to recover.
Fix a3700_fdt_fix_pcie_regions() to properly parse and update all addresses
in the `ranges` property according to
https://elinux.org/Device_Tree_Usage#PCI_Address_Translation
Now it is possible to increase PCIe MEM space from 16 MiB to maximal value
of 127 MiB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Fixes: cb2ddb291e ("arm64: mvebu: a37xx: add device-tree fixer for PCIe regions")
Reviewed-by: Stefan Roese <sr@denx.de>
Find PCIe DT node by compatible string instead of retrieving it by using
hardcoded DT path.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Change DT compatible string for A3700 PCIe from 'marvell,armada-37xx-pcie'
to 'marvell,armada-3700-pcie' to make U-Boot A3700 PCIe DT node compatible
with Linux' DT node.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add dts support for fu740. The HiFive Unmatched support is based on
fu740 cpu and drivers in following patch set.
Signed-off-by: Green Wan <green.wan@sifive.com>
[greentime.hu: set fu740 speed to 1.2GHz]
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Commit 2243d19e56 ("mmc: mmc-uclass: Use dev_seq() to read aliases
node's index") now actually enforces U-Boot's device enumeration policy,
where explicitly named devices come first, then any other non-named
devices follow, without filling gaps.
For quite a while we have had an "mmc1 = &mmc2;" alias in our
sunxi-u-boot.dtsi, which now leads to the problem that the SD card
(which was always mmc device 0) now gets to be number 2.
This breaks quite some boot scripts, including our own distro boot
commands, and some other features looking at $mmc_bootdev, also
fastboot.
Just add an explicit mmc0 alias in the very same file to fix this and
restore the old behaviour.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Samuel Holland <samuel@sholland.org>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Enable the true random number generator. It can be used, for example, to
generate partition UUIDs when partitioning with the gpt command. The
generator is already enabled in the device trees of several other
STM32MP1‐based boards, like DKx or DHCOM.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The AM64x SoC uses a central Device Management and Security Controller
(DMSC) processor that manages all the low-level device controls
including the system-wide SoC reset. The system-wide reset is managed
through the system reset driver.
Add a sysreset controller node as a child of the dmsc node to enable
the "reset" command from U-Boot prompt for the K3 AM642 SK.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM64x SoC uses a central Device Management and Security Controller
(DMSC) processor that manages all the low-level device controls
including the system-wide SoC reset. The system-wide reset is managed
through the system reset driver.
Add a sysreset controller node as a child of the dmsc node to enable
the "reset" command from U-Boot prompt for the K3 AM642 EVM.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The default U-Boot environment variables and design are all set up for
both the MAIN R5FSS clusters to be in Split-mode. This is the setting
in v2021.01 U-Boot and the dt nodes are synched with the kernel binding
property names in commit 468ec2f3ef ("remoteproc: k3_r5: Sync to
upstreamed kernel DT property names") merged in v2021.04-rc2.
The modes for both the clusters got switched back to LockStep mode by
mistake in commit 70e167495a ("arm: dts: k3-j721e: Sync Linux v5.11-rc6
dts into U-Boot") also in v2021.04-rc2. This throws the following warning
messages when early-booting the cores using default env variables,
k3_r5f_rproc r5f at 5d00000: Invalid op: Trying to start secondary core 7 in lockstep mode
Load Remote Processor 3 with data at addr=0x82000000 98484 bytes: Failed!
k3_r5f_rproc r5f at 5f00000: Invalid op: Trying to start secondary core 9 in lockstep mode
Load Remote Processor 5 with data at addr=0x82000000 98484 bytes: Failed!
Fix this by switching back both the clusters to the expected Split-mode.
Make this mode change in the u-boot specific dtsi file to avoid such
sync overrides in the future until the kernel dts is also switched to
Split-mode by default.
Fixes: 70e167495a ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Reported-by: Minas Hambardzumyan <minas@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The assembly output of the arch_initr_trap() function differed by a
single byte after common.h was removed from traps.c:
fff49a18 <arch_initr_trap>:
fff49a18: 94 21 ff f0 stwu r1,-16(r1)
fff49a1c: 7c 08 02 a6 mflr r0
fff49a20: 90 01 00 14 stw r0,20(r1)
-fff49a24: 80 62 00 44 lwz r3,68(r2)
+fff49a24: 80 62 00 38 lwz r3,56(r2)
fff49a28: 4b ff 76 19 bl fff41040 <trap_init>
fff49a2c: 80 01 00 14 lwz r0,20(r1)
fff49a30: 38 60 00 00 li r3,0
fff49a34: 38 21 00 10 addi r1,r1,16
fff49a38: 7c 08 03 a6 mtlr r0
This was causing a consistent hard lockup during the MMC read / loading
of the QoriQ FMan firmware on a P2041RDB board.
Re-adding the header causes identical assembly to be emitted and allows
the firmware loading and subsequent boot to succeed.
Fixes: 401d1c4f5d ("common: Drop asm/global_data.h from common header")
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Remove qemu_mips boards because DM migration doesn't make sense.
The board support for qemu_mips is already marked as deprecated
in Qemu in favour of the Malta board. Also qemu_mips support
has been removed from Linux a long time ago.
The official replacement is the Malta board. The same Malta U-Boot
image can be used with Qemu and on physical hardware.
All combinations of Big Endian and Little Endian as well as 32 bit
and 64 bit are supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When using LTO, we can throw away the --gc-sections flag, but only if
using private libgcc.
When using system's libgcc, --gc-sections is still needed, otherwise
linking will fail due to undefined references to libc's symbols.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building with LTO, using -ffunction-sections/-fdata-sections is not
useful anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
For some reason when building SPL for ARMv8 with LTO, the relocation
information is not discarded.
Discard it explicitly in the linker script.
This fixes LTO build for imx8mm_venice_defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Ford says that DM3730 needs board.c compiled without LTO flags.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Adam Ford <aford173@gmail.com>
When building with LTO, the compiler complains about type mismatch of
function usb_gadget_handle_interrupts(). This function is defined
without parameters in files
arch/arm/mach-rockchip/board.c
board/samsung/common/exynos5-dt.c
but it should have one parameter, int index.
Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When seaboard_defconfig is compiled with LTO, the compiler complains
about some instructions not being supported in ARM mode.
This is caused by arch/arm/mach-tegra/tegra20/warmboot_avp.c having
different CFLAGS declared in Makefile. This file needs to be compiled
without LTO.
Fix this by removing -flto for this file.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building imx8mp_evk_defconfig with LTO, the compiler complains
about type mismatch of function imx_eqos_txclk_set_rate() in file
drivers/net/dwc_eth_qos.c:845:12
which contains a weak definition of this function, vs file
arch/arm/mach-imx/imx8m/clock_imx8mm.c
which contains an implementation.
Change the type of this function in the implementation to fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When building with LTO, the compiler complains about type mismatch of
function clk_bsc_enable() in file:
arch/arm/cpu/armv7/kona-common/clk-stubs.c
vs other files that define or use this function:
warning: type of ‘clk_bsc_enable’ does not match original declaration.
Change the type of this function to that of the other usages.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When building keystone with LTO the compiler complains:
Error: selected processor does not support `smc #0' in Thumb mode
Fix this by removing -flto for the file implementing these SMC calls.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
When imx28_xea_defconfig is built with LTO, the compiler complains about
the two different declarations of _start:
include/asm-generic/sections.h as extern void _start(void);
arch/arm/cpu/arm926ejs/mxs/mxs.c as extern uint32_t _start;
Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix LTO build for some thumb-interwork usecases (such as for
da850evm_defconfig), where inline assmebly such as
mrc p15,0,r2,c1,c0,0
causes the compiler to fail during LTO linking with
Error: selected processor does not support `mrc p15,0,r2,c1,c0,0'
in Thumb mode
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
On ARM, the gd pointer is stored in registers r9 / x18. For this the
-ffixed-r9 / -ffixed-x18 flag is used when compiling, but using global
register variables causes errors when building with LTO, and these
errors are very difficult to overcome.
Richard Biener says [1]:
Note that global register vars shouldn't be used with LTO and if they
are restricted to just a few compilation units the recommended fix is
to build those CUs without -flto.
We cannot do this for U-Boot since all CUs use -ffixed-reg flag.
It seems that with LTO we could in fact store the gd pointer differently
and gain performance or size benefit by allowing the compiler to use
r9 / x18. But this would need more work.
So for now, when building with LTO, go the clang way, and instead of
declaring gd a global register variable, we make it a function call via
macro.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=68384
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Thumb instruction `ldr` is able to move high registers only from
armv7. For armv5 and armv6 we have to use `mov`.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
In style of linked lists, instead of declaring symbols for boundaries
of getopt options array in the linker script, declare corresponding
sections and retrieve the boundaries via static inline functions.
Without this clang's LTO produces binary without any getopt options,
because for some reason it thinks that array is empty (start and end
symbols are at the same address).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently we use incremental linking (ld -r) to link several object
files from one directory into one built-in.o object file containing the
linked code from that directory (and its subdirectories).
Linux has, some time ago, moved to thin archives instead.
Thin archives are archives (.a) that do not really contain the object
files, only references to them.
Using thin archives instead of incremental linking
- saves disk space
- apparently works better with dead code elimination
- makes things easier for LTO
The third point is the important one for us. With incremental linking
there are several options how to do LTO, and that would unnecessarily
complicate things.
We have to use the --whole-archive/--no-whole-archive linking option
instead of --start-group/--end-group, otherwise linking may fail because
of unresolved symbols, or the resulting binary will be unusable.
We also need to use the P flag for ar, otherwise final linking may fail.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With commit 8678776df6 (arm: mvebu: armada-3720-uDPU: fix PHY mode
definition to sgmii-2500) the PHY mode was switch to "sgmii-2500", even
when this is functionally incorrect since "2500base-x" was not supported
in U-Boot at that time. As this mode is now supported (at least present
in the headers), this patch moves back to the orinal version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Now that we have switched to binman to generate u-boot.itb for all
RISC-V boards, USE_SPL_FIT_GENERATOR is no longer needed and can
be dropped.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the new BINMAN_STANDALONE_FDT option for AE350 based SPL defconfigs,
so that binman is now used to generate u-boot.itb.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
By utilizing the newly introduced BINMAN_STANDALONE_FDT option, along
with a new dedicated device tree source file for the QEMU virt target
used for binman only, we can now use binman to generate u-boot.itb.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sort the RISC-V DTS build targets by their Kconfig target names in
alphabetical order.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present SiFive Unleashed board uses the Makefile to create the FIT,
using USE_SPL_FIT_GENERATOR, which is deprecated as per the Makefile
warning. Update to use binman instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch contains several DT files for SOM platform.
Carrier card is sck-kv (KV260) revA/B. SMK-K26 is description for starter
kit which doesn't have EMMC populated. And SM-K26 is full som with EMMC.
Files are divided in this way to make sure that SOM can be plugged to
different carrier card and all peripherals on SOM (or defined by a spec) can
be used by U-Boot. Full DT for SOM+CC can be merged together as overlays.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mainline kernel has psgtr driver that's why it is good to add description
to DT files. Some boards are just missing description for USB3 and sata.
zc1751-dc1 and p-a2197 are also missing clock descriptions for input
clocks.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Probe zynqmp firmware driver by adding zynqmp firmware, power &
ipi mailbox device tree nodes for mini emmc.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Add missing xlnx,mio-bank property to sdhci node. Also add properties with
0 value to have it listed in case that files are copied to different
projects where default case doesn't need to be handled in the same way.
That's why explicitly list them too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
I2C muxes that have the slave devices with same address are
falling into the below problem.
VCK190 system controller (SC) - zynqmp-e-a2197-00-revA.dts
I2C1 (0xff030000) -> Mux1 (@0x74) -> Channel 3 -> 0x50
I2C1 (0xff030000) -> Mux2 (@0x75) -> Channel 0 -> 0x50
1. SC accesses I2C1 - Mux1 (0x74) - Channel 3 and then
2. SC accesses I2C1 - Mux2 (0x75) - Channel 0.
Now it results in 2 slave devices with same address (0x50)
on the I2C bus, making the communication un-reliable.
When ' i2c-mux-idle-disconnect' is in DT, after '1', the Mux
channel output is disconnected, making none of the channels
available to the I2C1. So, there is no question of having the
same addressed slave (0x50) present on the bus when we are doing '2'.
Same pattern is seen in below two boards also.
ZCU208 - zynqmp-zcu208-revA.dts
ZCU216 - zynqmp-zcu216-revA.dts
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Add label to GPIO lines so the user-level applications can find any line
without knowing its physical path on System Controller on VCK190/VMK180.
These labels are describing EMIO gpio connection which depends on PL which
we normally don't describe but that's only way to go for now. Lately this
should be done out of this source code.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The 'silabs,skip-recall' property prevents interruption in operation of
the clock while the driver is being probed. Without this property, the
DDR DIMM clk can cause a failure during Versal's boot.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
All si570 which are used for ps reference clock generation should contain
silabs,skip-recall property not to cause break on ps clock.
On Versal boards this will cause hang on Versal cpu when it is booted at
the same time with SC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently all assembly optimized implementation of memory routines
show up at the top level of the RISC-V architecture Kconfig menu.
Let's group them together into a submenu.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present U-Boot SPL fails to boot on SiFive Unleashed board, due
to a load address misaligned exception happens when loading the FIT
image in spl_load_simple_fit(). The exception happens in memmove()
which is called by fdt_splice_().
Commit 8f0dc4cfd1 introduces an assembly version of memmove but
it does take misalignment into account (it checks if length is a
multiple of machine word size but pointers need also be aligned).
As a result it will generate misaligned load/store for the majority
of cases and causes significant performance regression on hardware
that traps misaligned load/store and emulate them using firmware.
The current behaviour of memcpy is that it checks if both src and
dest pointers are co-aligned (aka congruent modular SZ_REG). If
aligned, it will copy data word-by-word after first aligning
pointers to word boundary. If src and dst are not co-aligned,
however, byte-wise copy will be performed.
This patch was taken from the Linux kernel patch [1], which has not
been applied at the time being. It fixes the memmove and optimises
memcpy for misaligned cases. It will first align destination pointer
to word-boundary regardless whether src and dest are co-aligned or
not. If they indeed are, then wordwise copy is performed. If they
are not co-aligned, then it will load two adjacent words from src
and use shifts to assemble a full machine word. Some additional
assembly level micro-optimisation is also performed to ensure more
instructions can be compressed (e.g. prefer a0 to t6).
With this patch, U-Boot boots again on SiFive Unleashed board.
[1] https://patchwork.kernel.org/project/linux-riscv/patch/20210216225555.4976-1-gary@garyguo.net/
Fixes: 8f0dc4cfd1 ("riscv: assembler versions of memcpy, memmove, memset")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If /chosen was missing, chosen_offset would never get updated with the new
/chosen node. This would cause fdt_setprop_u32 to fail. This patch fixes
this by setting chosen_offset. In addition, log any errors from setting
boot-hartid as well.
Fixes: 5370478d1c ("riscv: Add boot hartid to device tree")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
At present there is only one Kconfig option CONFIG_SIFIVE_CLINT to
control the enabling of SiFive CLINT support in both SPL (M-mode)
and U-Boot proper (S-mode). So for a typical SPL config that the
SiFive CLINT driver is enabled in both SPL and U-Boot proper, that
means the S-mode U-Boot tries to access the memory-mapped CLINT
registers directly, instead of the normal 'rdtime' instruction.
This was not a problem before, as the hardware does not forbid the
access from S-mode. However this becomes an issue now with OpenSBI
commit 8b569803475e ("lib: utils/sys: Add CLINT memregion in the root domain")
that the SiFive CLINT register space is protected by PMP for M-mode
access only. U-Boot proper does not boot any more with the latest
OpenSBI, that access exceptions are fired forever from U-Boot when
trying to read the timer value via the SiFive CLINT driver in U-Boot.
To solve this, we need to split current SiFive CLINT support between
SPL and U-Boot proper, using 2 separate Kconfig options.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
This patch adds the dtsi/dts files needed to support the Marvell
Octeon TX2 CN913x DB. This is only the base port with not all
interfaces supported fully.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Some of the setups including cn9130 opens mmio window starting from
0xc0000000, reflect it in the u-boot code.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
There is region left by ATF, which needs to remain in memory to provide RT
services. To prevent overwriting it by u-boot, do not provide any mapping
for this memory region, so any attempt to access it will trigger
synchronous exception.
Update sr 2021-04-12:
Don't update armada3700/cpu.c mmu table, as this has specific changes
included in mainline.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This lacks the right u-boot specific DT include to make HDMI work.
Reported-by: B1oHazard <ty3uk@mail.ua>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This reverts commit bc8bbb77f7.
This commit breaks U-Boot booting on SiFive Unleashed board, as
there is no such CSR on U54 core.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Testing showed that disabling AI while leaving PLL1 enabled disabled the
aisram. This suggests that AI is a more appropriate clock for that ram
bank.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This is more consistent with the naming of other ram banks, and matches
what Linux is doing.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
These devices are necessary for the clock driver, which is required by the
sram driver, to run pre-relocation.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Update the Kconfig and the board file to make the am335x board compatible
with cape detection.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
The am335x from BeagleBone use i2c EEPROM to detect capes.
The memory is wired to i2c bus 2 therefore it need to be enabled.
Add i2c2 clock, pinmux description and pinmux enable function.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Add the extension_board_scan specific function to scan the information
of the EEPROM on one-wire and fill the extension struct.
Add the Kconfig symbol to enable the needs to detect DIPs.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Andre Przywara <andre.przywara@arm.com>
This commit extends the sandbox to implement a dummy
extension_board_scan() function and enables the extension command in
the sandbox configuration. It then adds a test that checks the proper
functionality of the extension command by applying two Device Tree
overlays to the sandbox Device Tree.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
[trini: Limit to running on sandbox]
Signed-off-by: Tom Rini <trini@konsulko.com>
Scrub duplicate /memory@* node entries here. Some R-Car DTs might
contain multiple /memory@* nodes, however fdt_fixup_memory_banks()
either generates single /memory node or updates the first /memory
node. Any remaining memory nodes are thus potential duplicates.
However, it is not possible to delete all the memory nodes right
away, since some of those might not be DRAM memory nodes, but some
sort of other memory. Thus, delete only the memory nodes which are
in the R-Car3 DBSC ranges.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add CPSW related nodes for AM642 SK. There are two CPSW ports on the
board but U-Boot supports only the first port.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM64 as CPSW3G IP with 2 external ports. Add DT entries for the same
(based on kernel DT).
Disable second port as its by default set to ICSS usage on EVM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM642 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM642 SoC. It supports the following interfaces:
* 2 GB LPDDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in switch and MAC mode
* x1 USB 3.0 Type-A port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x2 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin Raspberry Pi compatible GPIO header
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 54-pin header for Programmable Realtime Unit (PRU) IO pins
* Interface for remote automation. Includes:
* power measurement and reset control
* boot mode change
Add basic support for AM642 SK.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable support for selecting DTB within SPL based on EEPROM.
This will help to use single defconfig for both EVM and SK
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
I2C EEPROM data contains the board name and its revision.
Add support for:
- Reading EEPROM data and store a copy at end of SRAM
- Updating env variable with relevant board info
- Printing board info during boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Introduce ddr node for am642 needed for all ddr configurations.
Also, introduce the 1600MTs DDR4 configuration that is supported on the
am642-evm.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The AM642 EValuation Module (EVM) is a board that provides access to
various peripherals available on the AM642 SoC, such as PCIe, USB 2.0,
CPSW Ethernet, ADC, and more.
Add basic support.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The AM642 SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable applications such as
Motor Drives, PLC, Remote IO and IoT Gateways.
Some highlights of this SoC are:
* Dual Cortex-A53s in a single cluster, two clusters of dual Cortex-R5F
MCUs, and a single Cortex-M4F.
* Two Gigabit Industrial Communication Subsystems (ICSSG).
* Integrated Ethernet switch supporting up to a total of two external
ports.
* PCIe-GEN2x1L, USB3/USB2, 2xCAN-FD, eMMC and SD, UFS, OSPI memory
controller, QSPI, I2C, eCAP/eQEP, ePWM, ADC, among other
peripherals.
* Centralized System Controller for Security, Power, and Resource
Management (DMSC).
See AM64X Technical Reference Manual (SPRUIM2, Nov 2020)
for further details: https://www.ti.com/lit/pdf/spruim2
Introduce basic support for the AM642 SoC to enable SD/MMC boot.
Introduce a limited set of MAIN domain peripherals under cbass_main and
a set of MCU domain peripherals under cbass_mcu.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Change the memory attributes for the DDR regions used by the remote
processors on AM65x so that the cores can see and execute the proper code.
A separate table based on the previous K3 SoCs is introduced since the
number of remote processors and their DDR usage is different between the
SoC families.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The AM642 SoCs use the Main R5FSS0 as a boot processor, and runs
the R5 SPL that performs the initialization of the System Controller
processor and starting the Arm Trusted Firmware (ATF) on the Arm
Cortex A53 cluster. The Core0 serves as this boot processor and is
parked in WFE after all the initialization. Core1 does not directly
participate in the boot flow, and is simply parked in a WFI.
Power down these R5 cores (and the associated RTI timer resources
that were indirectly powered up) after starting up ATF on A53 by
using the appropriate SYSFW API in release_resources_for_core_shutdown().
This allows these Main R5F cores to be further controlled from the
A53 to run regular applications.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM642 early initialization sequence. Also
make use of existing logic to detect if ROM has already loaded sysfw
and avoided attempting to reload and instead just prepare to use already
running firmware.
While at it also initialize the MAIN_UART1 pinmux as it is used by SYSFW
to print diagnostic messages.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
For AM642, ROM supports loading system firmware directly
from boot image. ROM passes information about the number of
images that are loaded to bootloader at a specific address
that is temporary. Add support for storing this information
somewhere permanent before it gets corrupted.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
To access various control MMR functionality the registers need to
be unlocked. Do that for all control MMR regions in the MAIN domain.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
AM642 allows for booting from primary or backup boot media.
Both media can be chosen individually based on switch settings.
ROM looks for a valid image in primary boot media, if not found
then looks in backup boot media. In order to pass this boot media
information to boot loader, ROM stores a value at a particular
address. Add support for reading this information and determining
the boot media correctly.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The AM642 SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable applications such as
Motor Drives, PLC, Remote IO and IoT Gateways.
Some highlights of this SoC are:
* Dual Cortex-A53s in a single cluster, two clusters of dual Cortex-R5F
MCUs, and a single Cortex-M4F.
* Two Gigabit Industrial Communication Subsystems (ICSSG).
* Integrated Ethernet switch supporting up to a total of two external
ports.
* PCIe-GEN2x1L, USB3/USB2, 2xCAN-FD, eMMC and SD, UFS, OSPI memory
controller, QSPI, I2C, eCAP/eQEP, ePWM, ADC, among other
peripherals.
* Centralized System Controller for Security, Power, and Resource
Management (DMSC).
See AM64X Technical Reference Manual (SPRUIM2, Nov 2020)
for further details: https://www.ti.com/lit/pdf/spruim2
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
There are a number of platforms that depend on a SATA driver that has
been converted to require AHCI but the platforms themselves are behind
on other migrations that would make it trivial to enable AHCI. Disable
SATA in these cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a callback harts_early_init() to start.S to allow different riscv
hart perform setup code for each hart as early as possible. Since all
the harts enter the callback, they must be able to run the same
setup.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Check that a variable defined in /config/environment is found in the
run-time environment, and that clearing fdt_env_path from within that
node works.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Conditionalize the test being linked in]
Signed-off-by: Tom Rini <trini@konsulko.com>
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
instead using ls and awk to determine file size use stat instead.
This fixes an invalid size reporting for user or group names that have
spaces in them.
This adds a dependency on the stat application which is part of
the coreutils package which also includes ls.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Remove the invalid 'regulator-always-on' property to resolve:
starting USB...
Bus usb@2184000: Error enabling VBUS supply (ret=-13)
probe failed, error -13
Bus usb@2184200: USB EHCI 1.00
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.
Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Carrier board for
creating complete i.Core MX8M Mini C.TOUCH 2.0 board.
Linux dts commit details:
commit <a142252061ff> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
C.TOUCH 2.0")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini
from Engicam.
General features:
- NXP i.MX8M Mini
- Up to 2GB LDDR4
- 8/16GB eMMC
- Gigabit Ethernet
- USB 2.0 Host/OTG
- PCIe Gen2 interface
- I2S
- MIPI DSI to LVDS
- rest of i.MX8M Mini features
i.Core MX8M Mini needs to mount on top of Engicam baseboards
for creating complete platform solutions.
Linux dts commit details:
commit <470d6dad5ddd> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
SoM")
Add support for it.
Signed-off-by: Matteo Lisi <matteo.lisi@engicam.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
/soc@0
aips1
aips2
aips3
clk
iomuxc
osc_24m
are common node enablements across imx8mm platform for dm-spi,
dm-pre-reloc stages.
Move them into common dtsi, imx8mm-u-boot.dtsi
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add PHY's reset GPIO, so that U-Boot does a PHY hard reset.
This is needed, since the PHY might become unresponsive if
watchdog reboots the system while a transaction is ongoing.
The reset GPIO is added to the U-Boot specific DT files, since
the kernel does not setup the reserved registers correctly after
resetting the PHY and thus must not reset it.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In CP115, comphy4 can be configured into SFI port1
(in addition to SFI0). This patch adds the option
described above.
In addition, rename all existing SFI/XFI references:
COMPHY_TYPE_SFI --> COMPHY_TYPE_SFI0
No functional change for exsiting configuration.
Change-Id: If9176222e0080424ba67347fe4d320215b1ba0c0
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
According to Design Reference Specification the PHY PLL and Calibration
register from PHY0 are shared for multi-port PHY. PLL control registers
inside other PHY channels are not used.
This commit reworks utmi device tree nodes in a way that common PHY PLL
registers are moved to main utmi node. Accordingly both child nodes
utmi-unit range is reduced and register offsets in utmi_phy.h are updated
to this change.
This fixes issues in scenarios when only utmi port1 was in use, which
resulted with lack of correct pll initialization.
Change-Id: Icc520dfa719f43a09493ab31f671efbe88872097
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Even if comphy types of SATA2/SATA3/SGMII3 and comphy speeds of
1.5G/3G/6.25G were referenced in the driver non configuration (dts)
was using it.
This patch removes unused definitions.
Change-Id: I53ed6f9d3a82b9d18cb4e488bc14d3cf687f9488
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.
This patch does the following changes:
- PHY_TYPE_XX --> COMPHY_TYPE_XX
- PHY_SPEED_XX --> COMPHY_SPEED_XX
This improves readability, no functional change.
Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Because of the incorrectly supported SGMII_2500 mode, this patch
disables eth2 for now until this issue will be fixed in mainline.
Also fix an incorrect comment.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Marek Behun <marek.behun@nic.cz>
This patch adds the base support for the Marvell Octeon TX2 CN9130 CRB.
Not all interfaces are supported fully yet.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the dtsi/dts files needed to support the Marvell
Octeon TX2 CN9130 CRB. This is only the base port with not all
interfaces supported fully.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for SoCs based on AP807 die.
Remove unused include file for Armada-8020 SoC.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Use a single dtsi file for CP110 die instead of master/slave.
Moving to single file will allow miltiple DTSI inclusions with
re-defined CP index and name.
This change will also allow support for SoCs containing more than
two CP110 dies on board.
Move pin control definitions from CP110 DTS to board DTS files
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
With this extended test, we get the following failure :
=> ut dm reset_base
Test: dm_test_reset_base: reset.c
test/dm/reset.c:52, dm_test_reset_base(): reset_method3.id == reset_method3_1.id: Expected 0x14 (20), got 0x2 (2)
Test: dm_test_reset_base: reset.c (flat tree)
test/dm/reset.c:52, dm_test_reset_base(): reset_method3.id == reset_method3_1.id: Expected 0x14 (20), got 0x2 (2)
Failures: 2
A fix is needed in reset_get_by_index_nodev() when introduced in [1].
[1] ea9dc35aab ("reset: Get the RESET by index without device")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When zImage support was added to SPL, the messages were hidden to reduce
code size. However, the wrong config symbol was used. Since this file is
only built when CONFIG_SPL_FRAMEWORK=y, the messages were always hidden.
Use the correct symbol so the messages are printed in U-Boot proper.
Also use IS_ENABLED to drop the #ifdef.
Fixes: 431889d6ad ("spl: zImage support in Falcon mode")
Signed-off-by: Samuel Holland <samuel@sholland.org>
When flush_cache() is called during boot on our ~7M kernel image, the
hundreds of thousands of WATCHDOG_RESET calls end up adding
significantly to boottime. Flushing a single cache line doesn't take
many microseconds, so doing these calls for every cache line is
complete overkill.
The generic watchdog_reset() provided by wdt-uclass.c actually
contains some rate-limiting logic that should in theory mitigate this,
but alas, that rate-limiting must be disabled on powerpc because of
its get_timer() implementation - get_timer() works just fine until
interrupts are disabled, but it just so happens that the "big"
flush_cache() call happens in the part of bootm where interrupts are
indeed disabled. [1] [2] [3]
I have checked with objdump that the generated code doesn't change
when this option is left at its default value of 0: gcc is smart
enough to see that the ">=" comparison is tautologically true, hence
all assignments to "flushed" are eliminated as dead stores.
On our board, setting the option to something like 65536 ends up
reducing total boottime by about 0.8 seconds.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200605111657.28773-1-rasmus.villemoes@prevas.dk/
[2] https://lists.denx.de/pipermail/u-boot/2021-April/446906.html
[3] https://lists.denx.de/pipermail/u-boot/2021-April/447280.html
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
CONFIG_5xx hasn't existed since commit 5025897774 (powerpc, 5xx:
remove support for 5xx). Remove this last mention of it.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Having WATCHDOG_RESET() called automatically from the timer interrupt
runs counter to the idea of a watchdog device - if the board runs into
an infinite loops with interrupts still enabled, the watchdog will
never fire.
When using CONFIG_(SPL_)WDT, the watchdog_reset function is a lot more
complicated than just poking a few SOC-specific registers - it
involves accessing all kinds of global data, and if the interrupt
happens at the wrong time (say, in the middle of an WATCHDOG_RESET()
call from ordinary code), that can end up corrupting said global data.
Allow the board to opt out of calling WATCHDOG_RESET() from the timer
interrupt handler by setting CONFIG_SYS_WATCHDOG_FREQ to 0 - as that
setting is currently nonsensical (it would be compile-time
divide-by-zero), it cannot affect any existing boards.
Add documentation for both the existing and extended meaning of
CONFIG_SYS_WATCHDOG_FREQ.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Import updated devicetree files from the Linux v5.12 release.
Besides some node and audio port renames this changes the PHY modes to
either rgmii-id or rgmii-txid. From the board files the Pinephone sees
a lot of updates.
This also adds the long missing USB PHY property for controller 0, which
allows the U-Boot PHY driver to eventually use port 0 in host mode
(pending another U-Boot patch).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Update R40 .dts{,i} and dt-binding headers to current version from kernel.
Files taken from Linux 5.12-rc1 release
(commit fe07bfda2fb9cdef8a4d4008a409bb02f35f1bd8)
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch adds support for the following I2C devices connected to
I2C bus 0 on the Octeon EBB7304:
- Dallas DS1337 RTC
- TLV EEPROM
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
We already have a clock driver for MIPS Octeon. This patch changes the
Octeon DT nodes to supply the clock property via the clock driver
instead of using an hard-coded value, which is not correct in all cases.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the AHCI compatible SATA DT node to the Octeon CN73xx dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
For easy AHCI/ SATA integration, this patch adds board_ahci_enable()
for the MVEBU AHCI driver, which will be used by this platform. This
platform specific "enable" function will setup the proper endian
swapping in the AHCI controller so that it can be used by the common
AHCI code.
Additionally the endian swizzle entry for AHCI in
octeon_should_swizzle_table[] is removed, as this enabled the original
lowlevel code function, e.g. octeon_configure_qlm(), for the QLM setup
to work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the necessary platform infrastructure code, so that the
MIPS Octeon drivers "serial_octeon_pcie_console" & "serial_bootcmd" can
be used. This is e.g. the bootmem initialization in a compatible way to
the Marvell 2013 U-Boot, so that the exisiting PC remote tools like
"oct-remote-console" & "oct-remote-load" can be used. This is be done in
the newly introduced arch_misc_init(), which calls the necessary init
functions when enabled.
These patches are in preparation for the MIPS Octeon NIC23 board
support, which is a desktop PCIe target board enabling these features.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
As DEBUG is no Kconfig symbol, we can't use the IS_ENABLED() macros.
This patch switches to the unfortunately necessary #ifdef usage again
to make it work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
While porting from the Marvell source, I introduced a bug by misplacing
the parenthesis. This patch fixes this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the newly added C files to the Makefile to enable
compilation. This is done in a separate step, to not introduce build
breakage while adding the single files with potentially missing
externals.
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_qlm.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_fdt.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-qlm.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pcie.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-util.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-jtag.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-fdt.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-cfg.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
To match all other cvmx-* header, this patch moves the already existing
cvmx-lmcx-defs.h header one directory up.
Signed-off-by: Stefan Roese <sr@denx.de>
With the newly added headers and their restructuring (which macro is
defined where), some changes in the already existing Octeon files are
necessary. This patch makes the necessary changes.
Signed-off-by: Stefan Roese <sr@denx.de>
Import misc remaining header files from 2013 U-Boot. These will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Import cvmx-sso-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sriox-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sriomaintx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-smix-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sli-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sata-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-rst-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pow-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pki-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pip-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pepx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pemx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pcsx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pciercx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pcieepx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-npi-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-mio-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-l2c-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-ipd-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-gserx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-gmxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-fpa-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-dtx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-dpi-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-dbg-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-ciu-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-bgxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-asxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-agl-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import misc cvmx-helper header files from 2013 U-Boot. They will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This will be used by the upcoming Serdes and driver code ported from
the original 2013 U-Boot code to mainline.
Signed-off-by: Stefan Roese <sr@denx.de>
Import updated devicetree files from the Linux v5.12 release.
Besides some node and audio port renames this changes the PHY modes to
either rgmii-id or rgmii-txid. From the board files the Pinephone sees
a lot of updates.
This also adds the long missing USB PHY property for controller 0, which
allows the U-Boot PHY driver to eventually use port 0 in host mode
(pending another U-Boot patch).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Update R40 .dts{,i} and dt-binding headers to current version from kernel.
Files taken from Linux 5.12-rc1 release
(commit fe07bfda2fb9cdef8a4d4008a409bb02f35f1bd8)
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
-----BEGIN PGP SIGNATURE-----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=JwRN
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2021-04-24' of https://source.denx.de/u-boot/custodians/u-boot-mips
- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
This patch adds support for the following I2C devices connected to
I2C bus 0 on the Octeon EBB7304:
- Dallas DS1337 RTC
- TLV EEPROM
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
We already have a clock driver for MIPS Octeon. This patch changes the
Octeon DT nodes to supply the clock property via the clock driver
instead of using an hard-coded value, which is not correct in all cases.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the AHCI compatible SATA DT node to the Octeon CN73xx dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
For easy AHCI/ SATA integration, this patch adds board_ahci_enable()
for the MVEBU AHCI driver, which will be used by this platform. This
platform specific "enable" function will setup the proper endian
swapping in the AHCI controller so that it can be used by the common
AHCI code.
Additionally the endian swizzle entry for AHCI in
octeon_should_swizzle_table[] is removed, as this enabled the original
lowlevel code function, e.g. octeon_configure_qlm(), for the QLM setup
to work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the necessary platform infrastructure code, so that the
MIPS Octeon drivers "serial_octeon_pcie_console" & "serial_bootcmd" can
be used. This is e.g. the bootmem initialization in a compatible way to
the Marvell 2013 U-Boot, so that the exisiting PC remote tools like
"oct-remote-console" & "oct-remote-load" can be used. This is be done in
the newly introduced arch_misc_init(), which calls the necessary init
functions when enabled.
These patches are in preparation for the MIPS Octeon NIC23 board
support, which is a desktop PCIe target board enabling these features.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
As DEBUG is no Kconfig symbol, we can't use the IS_ENABLED() macros.
This patch switches to the unfortunately necessary #ifdef usage again
to make it work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
While porting from the Marvell source, I introduced a bug by misplacing
the parenthesis. This patch fixes this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the newly added C files to the Makefile to enable
compilation. This is done in a separate step, to not introduce build
breakage while adding the single files with potentially missing
externals.
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_qlm.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_fdt.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-qlm.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pcie.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-util.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-jtag.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-fdt.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-cfg.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
To match all other cvmx-* header, this patch moves the already existing
cvmx-lmcx-defs.h header one directory up.
Signed-off-by: Stefan Roese <sr@denx.de>
With the newly added headers and their restructuring (which macro is
defined where), some changes in the already existing Octeon files are
necessary. This patch makes the necessary changes.
Signed-off-by: Stefan Roese <sr@denx.de>
Import misc remaining header files from 2013 U-Boot. These will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Import cvmx-sso-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sriox-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sriomaintx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-smix-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sli-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sata-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-rst-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pow-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pki-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pip-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pepx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pemx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pcsx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pciercx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pcieepx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-npi-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-mio-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-l2c-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-ipd-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-gserx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-gmxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-fpa-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-dtx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-dpi-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-dbg-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-ciu-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-bgxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-asxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-agl-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import misc cvmx-helper header files from 2013 U-Boot. They will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This will be used by the upcoming Serdes and driver code ported from
the original 2013 U-Boot code to mainline.
Signed-off-by: Stefan Roese <sr@denx.de>
Add the MMC DT node to the Octeon EBB7304 DT file including the
regulator node for the MMC power supply.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the MMC DT node to the Octeon CN73xx dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Until now, the Octeontx MMC driver did only support the ARM Octeon
TX/Tx2 platforms. This patch adds support for the MIPS Octeon platform
to this driver. Here a short summary of the changes:
- Enable driver compilation for MIPS Octeon, including the MMC related
header file
- Reorder header inclusion
- Switch to using the clk framework to get the input clock
- Remove some functions for MIPS Octeon, as some registers don't
exist here
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The MT7688KN is a multi-chip package with 8MiB DDR1 KGD. So the DDR type
from bootstrap register must be ignored, and always be assumed as DDR1.
This patch fixes the displayed DDR type of mt7628.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The MT7688KN is a multi-chip package with 8MiB DDR1 KGD. So the DDR type
from bootstrap register must be ignored, and always be assumed as DDR1.
This patch fixes an issue that mt7628_ddr_pad_ldo_config() may be passed
with a wrong ddr_type in MT7688KN.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Make sure to reset the switch core at probe time.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Import the i.MX6SX based UDOO Neo dts files from Linux 5.12-rc1
and sync the i.MX6SX pinfunc.h
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for stack protector for UBOOT, SPL, and TPL
as well as new pytest for stackprotector
Signed-off-by: Joel Peshkin <joel.peshkin@broadcom.com>
Adjust UEFI build flags.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The current usage of the variable CFLAGS_NON_EFI on the x86 architecture
deviates from other architectures.
Variable CFLAGS_NON_EFI is the list of compiler flags to be removed when
building UEFI applications. It is not a list of flags to be added anywhere.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
So far U-Boot was hard coding a (surely sufficient) memory size of 512
MB, even though all machines out there have at least 4GB of DRAM.
Since U-Boot uses its memory knowledge to populate the EFI memory map,
we are missing out here, at best losing everything beyond 4GB on Midway
boxes (which typically come with 8GB of DRAM).
Since the management processor populated the DT memory node already with
the detected DRAM size and configuration, we use that to populate
U-Boot's memory bank information, which is the base for the UEFI memory
map.
This finally allows us to get rid of the NR_DRAM_BANKS=0 hack, that we
had in place to avoid U-Boot messing up the DT memory node before
loading the kernel.
Also, to cover the whole of memory, we need to enable PHYS_64BIT.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
All Calxeda machines are actually a poster book example of device tree
usage: the DT is loaded from flash by the management processor into
DRAM, the memory node is populated with the detected DRAM size and this
DT is then handed over to the kernel.
So it's a shame that U-Boot didn't participate in this chain, but
fortunately this is easy to fix:
Define CONFIG_OF_CONTROL and CONFIG_OF_BOARD, and provide a trivial
function to tell U-Boot about the (fixed) location of the DTB in DRAM.
Then enable DM_SERIAL, to let the PL011 driver pick up the UART platform
data from the DT. Also define AHCI, to bring this driver into the driver
model world as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
use 'select' to enable IRQ as it does not have architecture
specific dependency.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The GICv3 RM requires "The first 1KB of memory for the LPI Pending tables
must contain only zeros on initial allocation, and this must be visible
to the Redistributors, or else the effect is UNPREDICTABLE".
And as the following statement, we here clear the whole Pending tables
instead of the first 1KB.
"An LPI Pending table that contains only zeros, including in the first 1KB,
indicates that there are no pending LPIs.
The first 1KB of the LPI Pending table is IMPLEMENTATION DEFINED. However,
if the first 1KB of the LPI Pending table and the rest of the table contain
only zeros, this must indicate that there are no pending LPIs."
And there isn't any pending LPI under U-Boot, so it's unnecessary to
load the contents of the Pending table during the enablement, then set
the GICR_PENDBASER.PTZ flag.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # NXP LS1028A
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable PCIe by default in u-boot, this should eventually be made dynamic
in the runtime board config depending on the MCU configuration.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The sync of the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2") causes Ethernet to break on some
ODROID-C2. The PHY seems to need proper reset timing to be functional
in U-Boot and Linux afterwards. Readd the old PHY reset bindings for
dwmac until we support the new bindings in the PHY node.
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmB9NEccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBp1CACFd9d7fokb59aFGeta
RaVD4Ni/5WUMT2ulUWYVn2KPmDLouXKZfvQZxakTJJkLCKfIKpQJ6pw82SUPqNc1
xhFS+YOxuDwhbB6ksApq7eUOga9T/K3S/8T4gPWkAOsAwlJGeF5AE1uxWFLbiNzt
eC2kMtRnwHmRq+fOuLsz1EHHKGcp+mtOnXEy2tv23xcGMqeCPzGsK7DWp1dw66gc
sqj7RdkfP/Ies557Ai/NjfdiOx1ThuVmNz/CgJgVf2/vHiQNgi4jHHDYQG55nGzJ
ExLtlom0L3ttko/hlznANFfPD6PBeF03T1cOT8jgx9/RFIF6dqDoA1YOa2dajhuW
xq5k
=MPfk
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.07-b' of https://source.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.07 cycle:
This small feature set include support for 5th PIO bank on pio4 pinctrl
driver and a fix for the SPL on sama5d3.
This reverts commit 38d6b7ebda.
struct global_data contains a pointer to the bd_info structure. This
pointer was populated spl_set_bd() to a pre-allocated bd_info in the
".data" section. The referenced commit replaced this mechanism to one
that uses malloc(). That new mechanism is only used if SPL_ALLOC_BD=y.
which very few boards do.
The result is that (struct global_data)->bd is NULL in SPL on most
platforms. This breaks falcon mode, since arch_fixup_fdt() tries to
access (struct global_data)->bd and set the "/memory" node in the
devicetree. The result is that the "/memory" node contains garbage
values, causing linux to panic() as it sets up the page table.
Instead of trying to fix the mess, potentially causing other issues,
revert to the code that worked, while this change is reworked.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
in the early SPL boot stage whenever there is a call to udelay,
dm_timer_init fails to find the pit timer whenever it traverses
the device tree, if this property is not present
Signed-off-by: Manuel Reis <mluis.reis@gmail.com>
CC: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
This is a patchset which makes away with the .bind() controller indexing
workaround which was broken since before v2021.04, and then adds PHY
support and MX8M support on top of that. Better add it into the release
early to get as much testing as possible done, because this really does
a lot of changes to the ehci-mx6 driver.
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The standard compatible string is "usb-nop-xceiv", use it.
Note that keystone-k2g.dtsi already uses the aforementioned
compat string, so this patch can only remove the override.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
According to latest errata of J721e [1], HS400 mode is not supported
in MMCSD0 subsystem (i2024) and SDR104 mode is not supported in MMCSD1/2
subsystems (i2090). Therefore, replace mmc-hs400-1_8v with mmc-hs200-1_8v
in MMCSD0 subsystem and add a sdhci mask to disable SDR104 speed mode.
Also, update the itap delay values for all the MMCSD subsystems according
the latest J721e data sheet[2]
[1] - https://www.ti.com/lit/er/sprz455/sprz455.pdf
[2] - https://www.ti.com/lit/ds/symlink/tda4vm.pdf
Fixes: 70e167495a ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This adds support for devices with R40 dual rank DRAM, and asymmetric
A64 DRAM devices like the Pinephone/3GB.
Also we enable automatic gzipped kernel support, and allow scripted
DT overlay support. The rest of the patches are cleanups, but also
some sunxi-specific preparatory patches for USB3.0 and improved HDMI
support. The bulk of those changes will go through other trees, though.
Build-tested for all 156 sunxi boards, and boot tested on a A64, A20, R40,
H5, H6 and H616 board. USB, SD card, eMMC, HDMI and Ethernet all work
there (where applicable), with the exception of Ethernet on the H5. Since
this is already broken in v2021.04, I will send a separate fix.
Currently sunxi Makefile manually specifies full path to dw-hdmi common
code. However, that is not needed because it can be selected in Kconfig
instead.
Select proper symbol in Kconfig and drop path from Makefile.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The FIT description has access to the configuration variables. Use the
appropriate variable instead of hardcoding the address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
binman can fill in the default FIT configuration index as selected by
the "default-dt" argument, which is set to CONFIG_DEFAULT_DEVICE_TREE.
Let's respect the user's configuration by taking advantage of this
feature, instead of always defaulting to the first device tree in
CONFIG_OF_LIST.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Previously we do not have proper dual rank memory detection on R40
(because we omitted PIR_QSGATE, which does not work on R40 with our
configuration), and dual rank memory is just simply disabled as early
R40 boards available (Banana Pi M2 Ultra and Berry) have single rank
memory.
As a board with dual rank memory (Forlinx OKA40i-C) is now known to us,
we need to have a way to do memory rank detection to support that board.
Add some routine to detect memory rank by trying to access the memory
in rank 1 and check for error status of the memory controller, and then
enable dual rank memory on R40.
Similar routine can be used to detect half DQ width (which is also
detected by PIR_QSGATE on other SoCs), but it's left unimplemented
because there's no known R40 board with half DQ width now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: Move R40 detect code call into sunxi_dram_init()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Previously we have known that R40 has a configuration register for its
rank 1, which allows different configuration than rank 0. Reverse
engineering of newest libdram of A64 from Allwinner shows that A64 has
this register too. It's bit 0 (which enables dual rank in rank 0
configuration register) means a dedicated rank size setup is used for
rank 1.
Now, Pine64 scheduled to use a 3GiB LPDDR3 DRAM chip (which has 2GiB
rank 0 and 1GiB rank 1) on PinePhone, that makes asymmetric dual rank
DRAM support necessary.
Add this support. The code could support both A64 and R40, but because
dual rank detection is broken on R40 now, we cannot really use it on R40
currently.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
update ls1028aqds networking protocol, config in ls1021atwr, env in ls1012a
Add seli3 board support, booke watchdog, update eTSEC support in ppc-qemu
Add DM_SERIAL and lpuart in sl28, add DM_ETH support for some of powerpc platforms
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Minor fix to Apollo Lake devicetree bindings for FSP
- Refactor Designware PCIe drivers to core and SoC parts
- Add Amlogic Meson Designware PCIe controller driver
Add the FMan v3 nodes for the T1042D4RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T1042 SoC.
The device tree nodes are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When two FMan's are present on a board, the MDIO nodes are found at the
same offsets inside each FMan. This causes "non unique device name"
errors when registering the MDIO nodes under the second FMan. Fix this
by updating the offsets of the MDIO nodes to include the parent FMan's
offset.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the FMan v3 nodes for the T4240RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T4240 SoC.
The device tree nodes are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the FMan v3 nodes for the T2080RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T2080 SoC.
The device tree nodes are copied over with little modification from
the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Sometimes it is desireable to have the console output on the first
serial line. Introduce a configuration option for it (in the board
scope).
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With all preparations in place, switch over to DM_SERIAL.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move the CONFIG_DM_* from the defconfig to the TARGET_SL28 config.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SERIAL needs both the device tree as well as an early heap. Thus, we
have to call spl_early_init() to initialize the memory allocator and the
setup the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
To use the debug UART we have to call debug_uart_init() in the SPL. Do
so as soon as possible.
As an example, here is how you can use it on a LS1028A SoC:
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_BASE=0x21c0500
CONFIG_DEBUG_UART_CLOCK=200000000
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds a test case to test the new ofnode_phy_is_fixed_link() API.
Both the new and old DT bindings are covered.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The DSA sandbox driver is used for unit testing the DSA class code.
It implements a simple 2 port switch plus 1 CPU port, and uses a
very simple tag to identify the ports.
The DSA sandbox device is connected via CPU port to a regular Ethernet
sandbox device, called 'dsa-test-eth, managed by the existing eth
sandbox driver. The 'dsa-test-eth' is not intended for testing the
eth class code however, but it is used to emulate traffic through the
'lan0' and 'lan1' front pannel switch ports. To achieve this the dsa
sandbox driver registers a tx handler for the 'dsa-test-eth' device.
The switch ports, labeled as 'lan0' and 'lan1', are also registered
as eth devices by the dsa class code this time. So pinging through
these switch ports is as easy as:
=> setenv ethact lan0
=> ping 1.2.3.5
Unit tests for the dsa class code were also added. The 'dsa_probe'
test exercises most API functions from dsa.h. The 'dsa' unit test
simply exercises ARP/ICMP traffic through the two switch ports,
including tag injection and extraction, with the help of the dsa
sandbox driver.
I took care to minimize the impact on the existing eth unit tests,
though some adjustments needed to be made with the addition of
extra eth interfaces used by the dsa unit tests. The additional eth
interfaces also require MAC addresses, these have been added to the
sandbox default environment.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20210216224804.3355044-5-olteanv@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.
It is based on NXP LS1021 SoC and it provides following interfaces:
- IFC interface for NOR, NAND and external FPGA's
- 1 x RGMII ETH for debug purposes
- 2 x SGMII ETH for management communication via back-plane
- 1 x uQE HDLC for management communication via back-plane
- 1 x I2C for peripheral devices
- 1 x SPI for peripheral devices
- 1 x UART for debug logging
It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Includes DT definition for the following serdes protocols using various
PHY cards: 85xx, 13xx, 65xx, 9999, 7777.
Note that the default device tree for QDS now uses 85xx.
Enabling any of the others requires patching the fsl-ls1028a-qds.dtsi
file (the includes at the bottom of the file).
The phy-handle is specified as a path rather than a label because it is
possible to use the #include multiple times (meaning that more than one
PHY riser card of one type is inserted), and therefore, there would be
duplicate labels with the same name.
LBRW means that the board needs lane B rework before using this dtsi.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix copy/paste errors in the descriptions of mtrr_close () and mtrr_set().
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Several architectures had a default board_fit_config_name_match already;
this provides a generic weak version. We default to rejecting all configs.
This will use the FIT's default config, instead of the first config. This
may result in boot failures if there are multiple configurations and the
first config is *not* the default.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
We move qfw into its own uclass and split the PIO functions into a
specific driver for that uclass. The PIO driver is selected in the
qemu-x86 board config (this covers x86 and x86_64).
include/qfw.h is cleaned up and documentation added.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Fix inline comments and empty line in scmi driver and test files.
Remove test on IS_ENABLED(CONFIG_*_SCMI) in test/dm/scmi.c since these
configuration are expected enabled when CONFIG_FIRMWARE_SCMI is enabled
in sandbox configuration.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Implement sandbox regulator devices for SCMI voltage domains
and test them in DM scmi tests.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
It's an old bringup board with out upstream Linux or L4T support
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
On ARMv8 systems
load mmc 0:1 $loadaddr vmlinuz-5.10.0-3-arm64
booti
leads to a hanging system requiring to physically reset the system:
FDT and ATAGS support not compiled in - hanging
### ERROR ### Please RESET the board ###
For systems where physical access is difficult hanging is a poor choice.
It is preferable to reset the system when U-Boot reaches a state that is
not recoverable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The test adds two pinmux nodes to the device tree, one to test when a
register changes only one pin's mux (pinctrl-single,pins), and the other
to test when more than one pin's mux is changed (pinctrl-single,bits).
This required replacing the controller's register access functions when
the driver is used on sandbox.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With the last of the ARCH_P1022 platforms removed, finish removing the
rest of the platform support.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. It is also the only ARCH_T2081 board so remove that support
as well.
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <linuxfae@technexion.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Thomas Weber <weber@corscience.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM by the deadline.
Remove them.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Erik van Luijk <evanluijk@interact.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The mvsata_ide driver was due for DM conversion by v2019.07. As that
has long passed, remove the driver and disable it in the boards which
had enabled it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. In order to
convert to using the DWC SATA driver under DM further migrations are
required.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Signed-off-by: Tom Rini <trini@konsulko.com>
- uboot rockchip edp code is looking for a rockchip,panel property
for the edp dts node, so add it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
The linux code is setting polarity configuration to 3 but
uboot code is setting it to 1. Change the configuration to match the
linux configuration
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
According to linux commit "drm/rockchip: analogix_dp: add rk3399 eDP
support" (82872e42bb1501dd9e60ca430f4bae45a469aa64), rk3288 and rk3399
eDP IPs are nearly the same, the difference is in the grf register
(SOC_CON6 versus SOC_CON20). So, change the code to use the right
register on each IP.
The clocks don't seem to be the same, the eDP clock is not at index 1
on rk3399, so don't try changing the clock at index 1 to rate 0 on
rk3399.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
The current code is using an hard coded enum and the of node reg value of
endpoint to find out if the endpoint is mipi/hdmi/lvds/edp/dp. The order
is different between rk3288, rk3399 vop little, rk3399 vop big.
A possible solution would be to make sure that the rk3288.dtsi and
rk3399.dtsi files have "expected" reg value or an other solution is
to find the kind of endpoint by comparing the endpoint compatible value.
This patch is implementing the more flexible second solution.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmBwTr0cHHBhdHJpY2Uu
Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/plSwD/9SAhxTYqAblFZqZmJj
Lu+F5fwuXXd8S5LwqNeIKULv+UhJngClkE4HdjSl6T0yR10v6YkPNRDVj4+1gzBd
wZizmCsnqqDW0QGsTO5AVo+oTwhX4RHkvxEF7BjOqtVuoMZGiozE53+29QORHTnZ
+j8CYAeORf9wvGAi5y+Wr8ICqP6HwPJPNlta4S8iYC867BM38R9evBqynlaZaWPE
8FhaXwbAj9ZR9ifCiO+7ObgfXGDT63ejCecjE+539m3FWlBrn+/AWLsg4zF037Dw
DcV324pnVFP4AIOVsuc9hF7luAYctoXQcNHt1QbD3gmWqPQAgpH8Llfq5cMyudza
/m/112Y7fuLxO3F14DzZSj5l3ims0XG56Yg7zBwN6exDPr3iWA4UwTSH9lRJDnBq
aJyvLfAFAvz+X15oePjrQrVp7c+6MigeY2nmhVCWV53Yrl+/TnnekQXlHJ3TsHED
bPW5/LarLge18uACTZvLzYruIvDSU3INPP1W0vUu7YMDwuEp21K1GSspN7yA0yDK
nrWXxmYJGVWanAEvW//zuuqUhxtNjAb/qIQl0UgjFN9cDT5vJZ7oY3nWOwP+0V2a
o+qrRxBTWSVliOShYpfjyHRsASRna2QLLUNQaBeoUqZBKNnFvuw4LZzmqNvV+Idj
+XWRCiSDJnf1zRrMwFLvZZ+UTQ==
=4VxR
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210409' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
Split up get_soc_name(), clean the decoding up a bit, and set up
environment variables which contain the SoC type, package, revision.
This is useful on SoMs, where multiple SoC options are populated.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Replace the remaining printf in setup_boot_mode() by log macro
to handle filtering for log features.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Align the uart number in the trace of setup_boot_mode() with the name of
the uart/usart device (start at 1) and not with the instance value
(start at 0), i.e. the serial device sequence number and the index in
serial_addr[].
Fixes: f49eb16c17 ("stm32mp: stm32prog: replace alias by serial
device sequence number")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of TF-A FIP header in command stm32prog for all the boot
partition and not only the STM32IMAGE.
This patch is a preliminary patch to support FIP as second boot stage
after TF-A BL2 when CONFIG_TFABOOT is activated for trusted boot chain.
The FIP is archive binary loaded by TF-A BL2, which contains the secure OS
= OP-TEE and the non secure firmware and device tree = U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
7" OF is a capacitive touch 7" Open Frame panel solutions with
- 7" AUO B101AW03 LVDS panel
- EDT, FT5526 Touch
MicroGEA STM32MP1 is a STM32MP157A based Micro SoM.
MicroDev 2.0 is a general purpose miniature carrier board with CAN,
LTE and LVDS panel interfaces.
MicroGEA STM32MP1 needs to mount on top of MicroDev 2.0 board with
pluged 7" OF for creating complete MicroGEA STM32MP1 MicroDev 2.0
7" Open Frame Solution board.
Linux dts commit details:
commit <1d278204cbaa> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 7" OF")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
MicroDev 2.0 is a general purpose miniature carrier board with CAN,
LTE and LVDS panel interfaces.
Genaral features:
- Ethernet 10/100
- USB Type A
- Audio Out
- microSD
- LVDS panel connector
- Wifi/BT (option)
- UMTS LTE with sim connector (option)
MicroGEA STM32MP1 is a STM32MP157A based Micro SoM.
MicroGEA STM32MP1 needs to mount on top of this MicroDev 2.0 board
for creating complete MicroGEA STM32MP1 MicroDev 2.0 Carrier board.
Linux dts commit details:
commit <f838dae7afd0> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 board")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
MicroGEA STM32MP1 is a STM32MP157A based Micro SoM.
General features:
- STM32MP157AAC
- Up to 1GB DDR3L-800
- 512MB Nand flash
- I2S
MicroGEA STM32MP1 needs to mount on top of Engicam MicroDev carrier
boards for creating complete platform solutions.
Linux dts commit details:
commit <0be81dfaeaf8> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
SoM")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.
Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.
i.Core STM32MP1 needs to mount on top of this Carrier board for
creating complete i.Core STM32MP1 C.TOUCH 2.0 board.
Linux dts commit details:
commit <6ca2898df59f> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
C.TOUCH 2.0")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.
i.Core STM32MP1 needs to mount on top of this Evaluation board for
creating complete i.Core STM32MP1 EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <adc0496104b6> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
EDIMM2.2 Starter Kit")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPI Load isn't mandatory for STM32 builds.
Let's imply instead of select it to get rid of build
issues for non-SPI defconfigs.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam i.Core STM32MP1 SODIMM SoM has mounted 1x4Gb DDR3
which has 32bits width 528000Khz frequency.
Add DDR configuration via dtsi.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.
General features:
- STM32MP157A
- Up to 1GB DDR3L
- 4GB eMMC
- 10/100 Ethernet
- USB 2.0 Host/OTG
- I2S
- MIPI DSI to LVDS
- rest of STM32MP157A features
i.Core STM32MP1 needs to mount on top of Engicam baseboards
for creating complete platform solutions.
Linux commit details:
commit <30f9a9da4ee1> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
SoM")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
All these files are add for support rt-thread art-pi board
- add board/st/stm32h750-art-pi, defconfig, header support for u-boot
for more information about art-pi, please goto:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patchset has following changes:
- introduce stm32h750.dtsi to support stm32h750 value line
- add pin groups for usart3/uart4/spi1/sdmmc2
- add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
- add stm32h750i-art-pi.dts to support art-pi board
- add stm32h750i-art-pi-u-boot.dtsi to support art-pi board (u-boot)
art-pi board component:
- 8MiB qspi flash
- 16MiB spi flash
- 32MiB sdram
- ap6212 wifi&bt&fm
the detail board information can be found at:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Replace upper case by lower case in i2c nodes name.
update dmamux1 register range.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Some instances are missing in current support of stm32h743 MCU. This commit
adds usart3/uart4 and sdmmc2 support.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch is intend to add support stm32h750 value line,
just add stm32h7-pinctrl.dtsi for extending, with following changes:
- rename stm32h743-pinctrl.dtsi to stm32h7-pinctrl.dtsi
- move 'pin-controller' from stm32h7-pinctrl.dtsi to stm32h743.dtsi
- update stm32h743i-{disco, eval}.dts to include stm32h7-pinctrl.dtsi
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
As different boards has their own sdram hw connection, mount different
sdram modules, so move sdram timing parameter and pin configuration
to their board device tree.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This reverts the arch/arm/mach-imx/imx_bootaux.c changes of commit
805b3cac1e. The loader function name was changed so that it does
not clash with the generically available function in lib/elf.c.
imx-bootaux loads an elf file linked for an auxilary core. Thus the
loader function requires address translation from the auxilary core's
address space to where those are mapped into U-Boot's address space.
So the elf loader is specific and must not be replaced with a generic
loader which doesn't provide the address translation functionality.
Fixes commit 805b3cac1e ("lib: elf: Move the generic elf
loading/validating functions to lib")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Some board like imx8mm-evkb, IO voltage switch from 3.3v to 1.8v need
around 18ms, common code only delay 10ms, so need to delay extra 8ms.
Otherwise voltage switch will timeout when wait for data0 line.
This IO voltage switch time depends on board design, depend on the
PMIC and capacitance. imx8mm-evkb board use PCA9450(PMIC) and 10uF
capacitance.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
sel_input value for the following uart5 pins is
different between i.MX6UL and i.MX6ULL:
MX6_PAD_UART5_TX_DATA__UART5_DTE_RX
MX6_PAD_UART5_RX_DATA__UART5_DCE_RX
MX6_PAD_ENET1_RX_EN__UART5_DCE_RTS
MX6_PAD_ENET1_TX_DATA0__UART5_DTE_RTS
MX6_PAD_CSI_DATA02__UART5_DCE_RTS
As sel_input value for the second one is fixed by
the previous commit, fix the rest.
Signed-off-by: Yuichiro Goto <goto@k-tech.co.jp>
Enabled "fsl,legacy-bch-geometry" in U-Boot device tree overlay
to match the legacy BCH geometry layout, which mainline Linux
applies when "fsl,use-minimum-ecc" is not specified in the device
tree.
Reinstated SYS_NAND_ONFI_DETECTION, which when disabled, masked
the mismatch on SOMs with Winbond NAND flash chips.
Signed-off-by: Niel Fourie <lusus@denx.de>
Convert the Olimex Olinuxino board's support for MMC to driver model following
Fabio Estevam's excellent example from:
commit: 23013aa961:
mx23evk: Convert to driver model
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Add the dts file for the Olimex Olinuxino from the linux kernel, and enable
its use in this machine's defconfig.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Enable DM block, DM MMC and DM SATA support on iMX6 Udoo
convert board code to match the DM support.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Convert the two Embest boards to use DM MMC.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Import the iMX6 based marsboard and riotboard. dts files from Linux 5.12-rc1
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Import the iMX53 based usbarmory dts files from Linux 5.12-rc1
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Andrej Rosano <andrej@inversepath.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model support for MMC and SATA.
Note that DM_MMC requires aliases for your mmc devices so
they are added to the dts. Linux does not support enumerating mmc
devices by alias so these are not present in the Linux dts.
Note that we still need board_mmc_init() and board_mmc_getcd() for
not DM SPL to support MMC.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The fsl-usb dt bindings in Linux default dr_mode to 'host' for
backward compatibility however U-Boot prints an error if
this property does not exist. Declare it in the Gateworks
Ventana device-trees to avoid the error.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The OCRAM_S is regular memory, just like the OCRAM, add it to the MMU
tables so it can be used and cached.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add DEK encapsulation support for imx8. The DEK blob is generated by the
SECO through the SCFW API.
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add DEK blob encapsulation support for IMX8M through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application call.
U-boot sends and receives the DEK and the DEK blob binaries through OP-TEE
dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
It is highly recommended to set the PRIBLOB bitfield to 0x3 once your
encrypted boot image has booted up, this prevents the generation of new
blobs that can be used to decrypt an encrypted boot image. The PRIBLOB is
a sticky type bit and cannot be changed until the next power on reset.
Add the set_priblob_bitfield U-Boot command to prevent the generation of
new blobs.
Signed-off-by: Clement Le Marquis <clement.lemarquis@nxp.com>
Acked-by: Ye Li <Ye.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add function to send mailbox command via SMC to get usercode from SDM.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add signature with crc32 value for all images in binman node for FIT
image in device tree. And, enable FIT signature checking for Stratix10
and Agilex ATF and VAB sdmmc boot.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Changed to store QSPI reference clock in kHz instead of Hz in
boot scratch cold0 register for Stratix10 and Agilex.
This patch is in preparation for Intel N5X SDRAM driver
support. Reserved 4 bits for Intel N5X SDRAM driver,
and there will be 28 bits to store QSPI reference clock.
Due to limited bits, QSPI reference clock frequency is
converted to kHz from Hz.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Restructure Stratix10 and Agilex handoff code to used by
all SOC64 devices, in preparation to support handoff for
Diamond Mesa.
Remove wrap_pinmux_config_s10.c. Add wrap_handoff_soc64.c
which contains the generic function to parse the handoff
data.
Update system_manager_soc64.c to use generic handoff
function in wrap_handoff_soc64.c.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rearrange sequence of macros in handoff_soc64.h without any functionality
change. In preparation for Stratix10 and Agilex handoff function
restructuring.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Move Stratix10 and Agilex SPL common code to spl_soc64.c.
We are in preparation for new n5x device support.
No functional change in this patch.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
The uart nodes already provide <clocks> property for the driver to
dynamically calculate the correct clock frequency. There is no need
to keep the hard-coded <clock-frequency> property.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Tested-by: Padmarao Begari <padmarao.begari@microchip.com>
Provide optimized versions of memcpy(), memmove(), memset() copied from
the Linux kernel.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The value returned by setjmp must be nonzero. If zero is passed as
parameter it must be replaced by 1.
This patch reduces the code size a bit.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
In preparation to add SiFive Unmatched board support, let's rename
the existing fu540 board to unleashed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This adds the necessary bindings. Most of them are already there.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Rick Chen <rick@andestech.com>
Since commit 8891410c729b ("MLK-19848 mx6dq: Fix chip version issue for
rev1.3") it's not possible to call the HAB API functions on i.MX6DQ
SoC Rev 1.3:
Authenticate image from DDR location 0x12000000...
undefined instruction
pc : [<412c00dc>] lr : [<8ff560bc>]
reloc pc : [<c8b6d0dc>] lr : [<178030bc>]
sp : 8ef444a8 ip : 126e8068 fp : 8ff59aa8
r10: 8ffd51e4 r9 : 8ef50eb0 r8 : 006e8000
r7 : 00000000 r6 : 126ea01f r5 : 0000002b r4 : 126e8000
r3 : 412c00dd r2 : 00000001 r1 : 00000001 r0 : 00000063
Flags: nzCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
resetting ...
The hab.h code is defining the HAB API base address according to the
old SoC revision number, thus failing when calling the HAB API
authenticate_image() function.
Fix this issue by using mx6dq rev 1.3 instead of mx6dq rev 1.5.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since cmd_dek is using CAAM JR, so enable the CMD_DEK only when
HAS_CAAM is set
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add some SOC level codes and build configurations to use HAB lib for
CONFIG_IMX_HAB (secure boot), like adding the SEC_CONFIG fuse, enable
fuse driver, CAAM clock function, and add CAAM secure RAM to MMU table.
The FSL_CAAM is temporally not enabled for iMX8M when CONFIG_IMX_HAB is set,
because we don't need the CAAM driver for SPL.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The imx8mm has changed the address of rvt_hab, use new address for imx8mm.
The authentication procedure is same as imx8mq. In u-boot, the authentication
uses SIP call to trap ATF to run HAB authenticate.
Users need to add CONFIG_SECURE_BOOT=y to defconfig to enable the feature.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When building 32-bit targets with CONFIG_SECURE_BOOT and DEBUG enabled
the following warnings are displayed:
arch/arm/mach-imx/hab.c:840:41: warning: format '%lx' expects argument \
of type 'long unsigned int', but argument 3 has type 'uint32_t \
{aka unsigned int}' [-Wformat=]
printf("HAB check target 0x%08x-0x%08lx fail\n",
~~~~^
%08x
ddr_start, ddr_start + bytes);
arch/arm/mach-imx/hab.c:845:45: warning: format '%x' expects argument \
of type 'unsigned int', but argument 3 has type 'ulong \
{aka long unsigned int}' [-Wformat=]
printf("\nivt_offset = 0x%x, ivt addr = 0x%x\n", ivt_offset, ivt_addr);
~^
%lx
Fix warnings by providing the correct data type.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When booting in low power or dual boot modes the M4 binary is
authenticated by the M4 ROM code.
Add an option in hab_status command so users can retrieve M4 HAB
failure and warning events.
=> hab_status m4
Secure boot disabled
HAB Configuration: 0xf0, HAB State: 0x66
No HAB Events Found!
Add command documentation in mx6_mx7_secure_boot.txt guide.
As HAB M4 API cannot be called from A7 core the code is parsing
the M4 HAB persistent memory region. The HAB persistent memory
stores HAB events, public keys and others HAB related information.
The HAB persistent memory region addresses and sizes can be found
in AN12263 "HABv4 RVT Guidelines and Recommendations".
Reviewed-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The HABv4 implementation in ROM checks if HAB major version
in IVT header is 4.x.
The current implementation in hab.c code is only validating
HAB v4.0 and HAB v4.1 and may be incompatible with newer
HABv4 versions.
Modify verify_ivt_header() function to align with HABv4
implementation in ROM code.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add ability for hab_status command to show All HAB events and not just
HAB failure events
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently it's not possible to authenticate additional boot images in HAB
open configuration.
The hab.c code is checking if the SEC_CONFIG[1] fuse is programmed prior
to calling the hab_authenticate_image() API function. Users cannot check
if their additional boot images has been correctly signed prior to closing
their device.
Enable hab.c to authenticate additional boot images in open mode so HAB
events can be retrieved through get_hab_status() function.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Modify to use hab_rvt_failsafe function for failsafe ROM API, not
directly call its ROM address. This function will wrap the sip call for iMX8M
platforms.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Calling csf_is_valid() with an un-signed image may lead to data abort
as the CSF pointer could be pointing to a garbage address when accessed
in HAB_HDR_LEN(*(const struct hab_hdr *)(ulong)ivt_initial->csf).
Authenticate image from DDR location 0x80800000...
Check CSF for Write Data command before authenticating image
data abort
pc : [<fff5494c>] lr : [<fff54910>]
reloc pc : [<8780294c>] lr : [<87802910>]
sp : fdf45dc8 ip : 00000214 fp : 00000000
r10: fffb6170 r9 : fdf4fec0 r8 : 00722020
r7 : 80f20000 r6 : 80800000 r5 : 80800000 r4 : 00720000
r3 : 17a5aca3 r2 : 00000000 r1 : 80f2201f r0 : 00000019
Flags: NzcV IRQs off FIQs off Mode SVC_32
Resetting CPU ...
resetting ...
To avoid such errors during authentication process, validate IVT structure
by calling validate_ivt function which checks the following values in an IVT:
IVT_HEADER = 0x4X2000D1
ENTRY != 0x0
RES1 = 0x0
DCD = 0x0 /* Recommended */
SELF != 0x0 /* Absoulute address of IVT */
CSF != 0x0
RES2 = 0x0
This commit also checks if Image's start address is 4 byte aligned.
commit "0088d127 MLK-14945 HAB: Check if IVT valid before authenticating image"
removed as this patch addresses the issue.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are some changes to support ARM64 i.MX8M platform in this patches:
1. The hab_rvt base and function vectors are different as i.MX6/7
2. Need to bypass an workaround for i.MX6 to fix problem in MMU.
3. The x18 register needed save & restore before calling any HAB API. According
to ARM procedure call spec, the x18 is caller saved when it is used as
temporary register. So calling HAB API may scratch this register, and
cause crash once accessing the gd pointer.
On ARMv7, the r9 is callee saved when it is used as variable register. So
no need to save & restore it.
4. Add SEC_CONFIG fuse for iMX8M
When current EL is not EL3, the direct calling to HAB will fail because
CAAM/SNVS can't initialize at non-secure mode. In this case, we use
SIP call to run the HAB in ATF.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When loading kernel image, the image size is parsed from header, so it
does not include the CSF and IVT.
Add back the authenticate_image function to wrap the imx_hab_authenticate_image
with calculating IVT offset and full image size.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Prior instantiating RNG we have to ensure if the CAAM job rings are
available. Avoid hardcoded job ring max size and use the definition at
fsl_sec.h
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Prior calling sec_in32() we have to ensure CAAM clock is enabled, the
function sec_in32() is reading CAAM registers and if CAAM clock is disabled
the system will hang.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The CAAM output ring size register offset is currently defined in fsl_sec.h
as FSL_CAAM_ORSR_JRa_OFFSET, use this definition to avoid hardcoded value in
i.MX common code.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This code was originally developed by Raul Cardenas <raul.casas@nxp.com>
and modified to be applied in U-Boot imx_v2017.03.
More information about the initial submission can be seen
in the link below:
https://lists.denx.de/pipermail/u-boot/2016-February/245273.html
i.MX7D has an a protection feature for Manufacturing process.
This feature uses asymmetric encryption to sign and verify
authenticated software handled between parties. This command
enables the use of such feature.
The private key is unique and generated once per device.
And it is stored in secure memory and only accessible by CAAM.
Therefore, the public key generation and signature functions
are the only functions available for the user.
The manufacturing-protection authentication process can be used to
authenticate the chip to the OEM's server.
Command usage:
Print the public key for the device.
- mfgprot pubk
Generates Signature over given data.
- mfgprot sign <data_address> <data_size>
Signed-off-by: Raul Ulises Cardenas <raul.casas@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MQ B2 is using same value in OCOTP_READ_FUSE_DATA like B1, so
we have to check the ROM verision to distinguish the revision.
As we have checked the B1 rev for sticky bits work around in
secure boot. So it won't apply on B2.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The value of Unique ID in uboot and kernel is different for iMX8MP:
serial#=02e1444a0002aaff
root@imx8mpevk:/sys/devices/soc0# cat soc_uid
D699300002E1444A
The reason is that Fuse Addresses of Unique ID of iMX8MP are 0x420 and
0x430.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For dual core and single core iMX8M parts, the thermal node and PMU node
in kernel DTB also needs update to remove the refers to deleted core nodes.
Otherwise both driver will fail to work.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are 3 part numbers for 11x11 i.MX8MNano with different core number
configuration: UltraLite Quad/Dual/Solo
Comparing with i.MX8MN Lite parts, they have MIPI DSI disabled. So
checking the MIPI DSI disable fuse to recognize these parts.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add dedicated defconfigs for iMX8MN low drive mode which set the VDD_SOC
and VDD_DRAM to 0.8v, DDR at 1600MTS (800Mhz clock) and GPU at 200Mhz.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for iMX8MN LPDDR4 EVK board which uses 2GB LPDDR4 and
PCA9450B PMIC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
No board uses this driver any more: remove it.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Gerald Kerma <drEagle@doukki.net>
CC: Stefan Roese <sr@denx.de>
CC: Pantelis Antoniou <panto@antoniou-consulting.com>
Update hwpartition usage
Check bootbus's arguments
workaround for erratum A-011334 for fsl_esdhc driver
add pulse width detection workaround for fsl_esdhc driver
Use alias num before checking mmc index when creating device
HS400 mode on the LS1028A SoC isn't reliable. The linux driver has a
workaroung for the pulse width detection. Apply this workaround in
u-boot, too.
This will make HS400 mode work reliably on the LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
LS1028A SoCs are restricted in what divider values are allowed for HS400
mode. This is basically a port from the corresponding linux driver.
Signed-off-by: Michael Walle <michael@walle.cc>
The static ethernet link type config code is no more needed because now handled by
the meson8b glue driver, delete it.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The ethernet memory power domain is handled by the meson-ee-pwrc driver,
delete the static code.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Trusted Firmware now adds the /reserved-memory subnode to the DT at
runtime[1], putting in the right values.
Drop our hard-coded version, as this might clash with the actual values
(which have also changed), and rely on TF-A to add the node.
[1] https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/7770
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Loading Trusted-Firmware's BL31 at 16KB into DRAM was originally a hack
to allow sharing more code with the other SoCs (which use this offset
in SRAM). However there is no longer a reason for that, as the
problematic macros have been properly separated there.
The latest (and hopefully final) TF-A code drop now changes the load
address to the beginning of DRAM, which is also more easily protected
by the Trustzone memory controller (code to be done).
Adjust the load address of BL31 now, to avoid any issues with
incompatible versions later on (the TF-A patches are about to be merged).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmBi3oscHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKr+CACDQJT4hGCDwc7XFjOw
RN0aGRC6eGF4q3kL4VjBazCM1SBNs3vdVZV+bnYl3ioSNzy43K7CyFqqUlJH7CJV
dakvNn71xVoQD3Xw3+I4ALibbD/tlli4vwMOeN4KlWCIdNrRrtUOQpli0M0BVDkL
0IWMDf6OLAfw1uytubsQBVitFBQoiuE3ihSphoyTOFwQdI+xsMue5uVq+O0kDqU4
gotBzmoSq5LONyNSdpHxXqujU4oXkuOr/TsVTOoRtEkQ63zVbfNWOg951is+UaHa
F7f6W+cWdlb+HBs6TFb+Gva0TMmyWIH05jyIS52k6uFVM0tyFCOJFeZp81cjPP4L
O3KI
=ywRG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.07-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.07 cycle:
This small feature set includes the implementation of the slew rate for
the PIO4 pin controller device, and a fix for arm926ejs-based
microprocessors that avoids a crash.
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:
- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In zynqmp.dtsi file renamed "clk_sys" clock to "controller" and
"clk_flash" clock to "bus" as per upstreamed Arasan NAND driver.
This fixes NAND driver probe failure.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update the following device tree properties for nand flash
- Set software ecc mode.
- Set bch as ecc algo.
- Set read block to 0.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
EMMC will have bus-width 8 and it is non-removable in general. These
are missing from dt node. Add bus-width and non-removable parameters
to emmc node.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add initial support for NanoPi M4B, a minor revision of
the original NanoPi M4.
Commit details of rk3399-nanopi-m4b.dts sync from Linux 5.12-rc4:
"arm64: dts: rockchip: Add NanoPi M4B board"
(sha1: c7b03115003f7f337ab165542cee37148cf30a8a)
Signed-off-by: Alexandre Vicenzi <alexandre.vicenzi@suse.com>
Reviewed-by: Kever Yang <kever.yang@rock-cihps.com>
NanoPi R4s is SBC base on Rockchip RK3399 hexa-core processor with
dual-Core Cortex-A72 and Mali-T864 GPU with 4GiB(LPDDR4) of RAM, SD card support,
including 2 gigabit ethernet(RTL8211E 1Gbps - RTL8111H 1Gbps) and 2 USB 3.0 port.
port.It also has two GPIO headers which allows further peripherals to be used.
The devicetree file is taken of the rk3399 nanopi4 Linux kernel [1].
[1] e7a0959082
Signed-off-by: xiaobo <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A commit from last year re-imported the DTS files form the upstream kernel.
By doing so the VDD_LOG regulator in the board's DTS was dropped.
Let's restore this, but move it into the u-boot overlay to prevent this
issue in the future.
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This brings the actual rk3368-lion devicetree files from Linux 5.10
instead of using something separate.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is the state as of v5.10 + the recently added timer0 phandle
targetted at the 5.12 merge window.
With this the non-mainline nodes like the dmc move to a separate
rk3368-u-boot.dtsi that is included from the board-specific
-u-boot.dtsi files, similar to how rk3399 does this.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the STACK_R_ADDR at 0x600000 (6MB) we're competing with
with the loading address of either u-boot or atf parts, so move
that away to 0x4000000 (64MB) similar to rk3399.
Only lion currently sets that at all but not sheep the second
rk3368 board, so just move that to the Kconfig for rk3368 similar
to rk3399 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To prevent running out of memory, increase SYS_MALLOC_F_LEN to 0x4000
similar to what rk3399 uses.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On RISC-V the symbols __dyn_sym_start, dyn_sym_end are referenced in
efi_runtime_relocate().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
