Add support for reading bootscript and bootscript header from SD. Also
renamed macros *_FLASH to *_DEVICE to represent SD alongwith NAND and
NOR flash.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Without this, GCC uses the toolchain default, which may be incompatible
with -maltivec.
Signed-off-by: Scott Wood <oss@buserror.net>
Reviewed-by: York Sun <york.sun@nxp.com>
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In non-secure boot scenario from NAND, this address will map to CPC
configured as SRAM. But in case of secure boot, this default address
always maps to IBR (Internal Boot ROM).
The IBR code requires that the bootloader(U-boot) must lie in 0 to 3.5G
address space i.e. 0x0 - 0xDFFFFFFF.
For secure boot target from NAND, the text base for SPL is kept same as
non-secure boot target i.e. 0xFFFx_xxxx but the SPL U-boot binary will
be copied to CPC configured as SRAM with address in 0-3.5G(0xBFFC_0000)
As a the virtual and physical address of CPC would be different. The
virtual address 0xFFFx_xxxx needs to be mapped to physical address
0xBFFx_xxxx.
Create a new PBI file to configure CPC as SRAM with address 0xBFFC0000
and update DCFG SCRTACH1 register with location of Header required for
secure boot.
The changes are similar to
commit 467a40dfe3
powerpc/mpc85xx: SECURE BOOT- NAND secure boot target for P3041
While P3041 has a 1MB CPC and does not require SPL. On T104x, CPC
is only 256K and thus SPL framework is used.
The changes are only applicable for SPL U-Boot running out of CPC SRAM
and not the next level U-Boot loaded on DDR.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of Chain of Trust for Secure boot, the SPL U-Boot will validate
the next level U-boot image. Add a new function spl_validate_uboot to
perform the validation.
Enable hardware crypto operations in SPL using SEC block.
In case of Secure Boot, PAMU is not bypassed. For allowing SEC block
access to CPC configured as SRAM, configure PAMU.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Define a platform data structure for the MPC85XX GPIO driver to allow
use of the driver without device tree. Users should define the GPIO
blocks for their platform like this:
struct mpc85xx_gpio_plat gpio_blocks[] = {
{
.addr = 0x130000,
.ngpios = 32,
},
{
.addr = 0x131000,
.ngpios = 32,
},
};
U_BOOT_DEVICES(my_platform_gpios) = {
{ "gpio_mpc85xx", &gpio_blocks[0] },
{ "gpio_mpc85xx", &gpio_blocks[1] },
};
This is intended to build upon the recent submission of the base
MPC85XX driver from Mario Six. We need to use that new driver
without dts support and this patch gives us that flexibility.
This has been tested on a Freescale T2080 CPU, although only the first
GPIO block.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Mario Six <mario.six@gdsys.cc>
Tested-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Simon Glass <sjg@chromium.org>
The errata command is useless in SPL, so don't build it. This fixes
multiple build failures on PowerPC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: York Sun <york.sun@nxp.com>
Fixes: 92623672f9 ("fsl: usb: make errata function common for PPC and ARM")
This patch adds a driver for the built-in GPIO controller of the MPC85XX
SoC (probably supporting other PowerQUICC III SoCs as well).
Each GPIO bank is identified by its own entry in the device tree, i.e.
gpio-controller@fc00 {
#gpio-cells = <2>;
compatible = "fsl,pq3-gpio";
reg = <0xfc00 0x100>
}
By default, each bank is assumed to have 32 GPIOs, but the ngpios
setting is honored, so the number of GPIOs for each bank in configurable
to match the actual GPIO count of the SoC (e.g. the 32/32/23 banks of
the P1022 SoC).
The usual functions of GPIO drivers (setting input/output mode and output
value setting) are supported.
The driver has been tested on MPC85XX, but it is likely that other
PowerQUICC III devices will work as well.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Replace a number of array length calculations with the ARRAY_SIZE()
macro, for clarity.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: York Sun <york.sun@nxp.com>
Since CONFIG_OF_BOARD_SETUP depends on CONFIG_OF_LIBFDT:
config OF_BOARD_SETUP
bool "Set up board-specific details in device tree before boot"
depends on OF_LIBFDT
...
remove superfluous tests of CONFIG_OF_LIBFDT when testing for
CONFIG_OF_BOARD_SETUP.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[trini: Typo fix: s/ifdefi/ifdef/]
Signed-off-by: Tom Rini <trini@konsulko.com>
While enabling L2 cache, the value of L2PE (L2 cache parity/ECC
error checking enable) must not be changed while the L2 cache is
enabled.
So, L2PE must be set before enabling L2 cache.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Commit ac337168a unified functions to flush and invalidate dcache by
range. These two functions were no-op for SoCs other than 4xx and
MPC86xx. Adding these functions seemed to be correct but introduced
issues when the dcache is flushed. While the root cause is under
investigation, disable these functions for affected SoCs so various
drivers can work.
Signed-off-by: York Sun <york.sun@nxp.com>
For SoCs that contain multiple SEC engines, each of them needs
to be initialized (by means of initializing among others the
random number generator).
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some SOCs, specifically the ones in the C29x familiy can have
multiple security engines. This patch adds a system configuration
define which indicates the maximum number of SEC engines that
can be found on a SoC.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To enable DM on MPC85xx, we need pre-relocation malloc, which is
implemented in this patch.
We also make sure that the IVORs are always 4-aligned on e500 to prevent
alignment exceptions caused by code changes in start.S.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Cc: York Sun <york.sun@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.
This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
Kconfig options must defined in the defconfig files. Since RSA_SOFTWARE_EXP
relies on CONFIG_DM, unless it is set in kconfig we cannot enable RSA.
Remove the hacks which enable CONFIG_DM in header files and update the
defconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Not only powerpc/mpc85xx but also Freescale Layerscape platforms will
use fdt_fixup_fman_firmware() to insert Fman ucode blob into the device
tree. So move the function to Fman driver code.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the QE firmware struct is shared with Fman, move the header file
out of drivers/qe/.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PAMU driver basic support for usage in Secure Boot.
In secure boot PAMU is not in bypass mode. Hence to use
any peripheral (SEC Job ring in our case), PAMU has to be
configured.
The patch reverts commit 7cad2e38d6.
The Header file pamu.h and few functions in driver have been derived
from Freescale Libos.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Chain of Trust is enabled for PowerPC platforms for Secure Boot.
CONFIG_BOARD_LATE_INIT is defined.
In board_late_init(), fsl_setenv_chain_of_trust() is called which
will perform the following:
- If boot mode is non-secure, return (No Change)
- If boot mode is secure, set the following environmet variables:
bootdelay = 0 (To disable Boot Prompt)
bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script)
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
A function is created to detrmine if the boot mode is secure
or non-secure for differnt SoC's.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There are two phases in Secure Boot
1. ISBC: In BootROM, validate the BootLoader (U-Boot).
2. ESBC: In U-Boot, continuing the Chain of Trust by
validating and booting LINUX.
For ESBC phase, there is no difference in SoC's based on ARM or
PowerPC cores.
But the exit conditions after ISBC phase i.e. entry conditions for
U-Boot are different for ARM and PowerPC.
PowerPC:
If Secure Boot is executed, a separate U-Boot target is required
which must be compiled with a diffrent Text Base as compared to
Non-Secure Boot. There are some LAW and TLB settings which are
required specifically for Secure Boot scenario.
ARM:
ARM based SoC's have a fixed memory map and exit conditions from
BootROM are same irrespective of boot mode (Secure or Non-Secure).
Thus the current Secure Boot functionlity has been split into
two parts:
CONFIG_CHAIN_OF_TRUST
This will have the following functionality as part of U-Boot:
1. Enable commands like esbc_validate, esbc_halt
2. Change the environment settings based on bootmode, determined
at run time:
- If bootmode is non-secure, no change
- If bootmode is secure, set the following:
- bootdelay = 0 (Don't give boot prompt)
- bootcmd = Validate and execute the bootscript.
CONFIG_SECURE_BOOT
This is defined only for creating a different compile time target
for secure boot.
Traditionally, both these functionalities were defined under
CONFIG_SECURE_BOOT. This patch is aimed at removing the requirement
for a separate Secure Boot target for ARM based SoC's.
CONFIG_CHAIN_OF_TRUST will be defined and boot mode will be
determine at run time.
Another Security Requirement for running CHAIN_OF_TRUST is that
U-Boot environemnt must not be picked from flash/external memory.
This cannot be done based on bootmode at run time in current U-Boot
architecture. Once this dependency is resolved, no separate
SECURE_BOOT target will be required for ARM based SoC's.
Currently, the only code under CONFIG_SECURE_BOOT for ARM SoC's is
defining CONFIG_ENV_IS_NOWHERE
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_CMD_BLOB must be defined in case of Secure Boot. It was
earlier defined in all config files. The definition has been
moved to a common file which is included by all configs.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Add device tree example file for xilinx-ppc440-generic and
xilinx-ppc405-generic
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
The old mail address will stop working soon.
Update it all the files
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of xilinx-ppc440
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of the xilinx-ppc405
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
ml507 is just a specialized version of the xilinx-ppc440-generic
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Incorrect DDR law was created in case of B4860qds after commit
2d2f490d. Return value of ffs64() differs from __ffs64(), eg.
ffs64(0x80000000) = 0x20
__ffs64(0x80000000) = 0x1f
As a result of this change, callers need to adjust the expected
return value by removing -1.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Users migrating Freescale's PowerPC SoC U-Boot code to their custom
board, often overlook the need to execute set_liodns() and
setup_portals() being called by platform files.
So Move set_liodns() and setup_portals() to common u-boot boot
sequence
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
clang-3.8 reports that serial_putc_raw_dev in serial_ns16550.c is
unused. Further investigation shows that we have 3 places that
implement this function and no callers, remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For compatibility clang will report some gcc version. However since we
are checking gcc versions in order to then fail to build, we should
limit these tests only to when we are using gcc and not clang.
Signed-off-by: Tom Rini <trini@konsulko.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
board_init_f_mem() alters the C runtime environment's
stack it is actually already using. This is not a valid
behaviour within a C runtime environment.
Split board_init_f_mem into C functions which do not alter
their own stack and always behave properly with respect to
their C runtime environment.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
since:
commit: f05ad9ba "Add a way to skip relocation"
tqm5200s board fails to boot. Reason is that
board_init_f has a function parameter bootflag,
which is not setup in
in arch/powerpc/cpu/mpc5xxx/start.S _start
So board_init_f gets a undefined bootflag,
currently the gd pointer address. Unfortunately
this address sets the GD_FLG_SKIP_RELOC bit,
so u-boot code gets not relocated and u-boot
does not boot ...
Init bootflag with 0, and tqm5200 boots fine again.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <yorksun@freescale.com>
GCC 5.x does not like sizeof(array_variable) and errors out. Change these
calls to be instead sizeof(u8) (as that's what serdes_prtcl_map is) *
SERDES_PRCTL_COUNT (the number of array elements).
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0,
T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on
LS102x Rev2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
move arch/powerpc/include/asm/fsl_errata.h to include/fsl_errata.h
to make it public for both ARM and POWER SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix soc.h path in fsl_errata.h]
Reviewed-by: York Sun <yorksun@freescale.com>
In preparation of some new Liebherr boards to be added soon, a new
"liebherr" vendor directory gets created, and the "lwmon5" board
directory is moved into this new vendor directory.
cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The removal of some PPC4xx boards did not catch all references to
these boards. This patch now removes all remnants still left.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Unify serial_ppc, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add TODO comment]
Signed-off-by: Tom Rini <trini@konsulko.com>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
The gdsys strider board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x 10/100 Mbit/s Ethernet (optional)
- Lattice ECP3 FPGA connected via eLBC
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
[trini: Drop setting CONFIG_SYS_GENERIC_BOARD, this is always true now]
Signed-off-by: Tom Rini <trini@konsulko.com>
In 522b021 we dropped 'PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4)' lines in
the mpc85xx linker scripts as this is not required and breaks newer
binutils. This commit cleans up the rest of the powerpc linker scripts.
Signed-off-by: Tom Rini <trini@konsulko.com>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In binutils-2.25, the _GLOBAL_OFFSET_TABLE_ symbols defined by PROVIDE in
u-boot.lds overrides the linker built-in symbols
(https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commitdiff;
h=b893397a4b1316610f49819344817715e4305de9),
so the linker is treating _GLOBAL_OFFSET_TABLE_ as a definition into the
.reloc section.
To align with the change of binutils-2.25, the _GLOBAL_OFFSET_TABLE_ symbol
should not be defined in sections, and the symbols in linker generated .got
section should be used(https://sourceware.org/ml/binutils/2008-09/
msg00122.html)
Fixed the following build errors with binutils-2.25:
| powerpc-poky-linux-gnuspe-ld.bfd: _GLOBAL_OFFSET_TABLE_ not defined in
linker created .got
Signed-off-by: Zhenhua Luo <zhenhua.luo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
A number of headers define functions as "extern inline" which is
causing problems with gcc5. The reason is that starting with
version 5.1, gcc defaults to the standard C99 semantics for the
inline keyword.
Under the traditional GNU inline semantics, an "extern inline"
function would never create an external definition, the same
as inline *without* extern in C99. In C99, and "extern inline"
definition is simply an external definition with an inline hint.
In short, the meanings of inline with and without extern are
swapped between GNU and C99.
The upshot is that all these definitions in header files create
an external definition wherever those headers are included,
resulting in multiple definition errors at link time.
Changing all these functions to "static inline" fixes the problem
since this works as desired in all gcc versions. Although the
semantics are slightly different (a static inline definition may
result in an actual function being emitted), it works as intended
in practice.
This patch also removes extern prototype declarations for the
changed functions where they existed.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Remove __ilog2_u64 and ffs4 from powerpc bitops to align with the
kernel implementation.
Use the generic __ffs64 instead of a custom powerpc implementation.
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This board runs a P5020 or P5040 chip, and utilizes
an EEPROM with similar formatting to the Freescale P5020DS.
Large amounts of this code were developed by
Adrian Cox <adrian at humboldt dot co dot uk>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2081 rev 1.1 changes MEM_PLL_RAT in RCW which requires new parsing
for PLL ratio.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
qe-tdm is muxed with diu, if hwconfig setted as qe-tdm,
assign muxed pins to qe-tdm, then delete diu node from
device tree.
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fsl_dtsec.h & fsl_tgec.h & fsl_fman.h can be shared on both ARM
and PPC, move it out of ppc to include/, and change the path in
drivers accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There are various toolchain issues that cause us to produce invalid
binaries with certain gcc 4.8.x and 4.9.x versions when we don't pass
this flag in.
Tested-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform has not gone into production. So lets remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 8fe11b8901.
I'll add support to lwmon5 in the next patch and will remove
support for the broken lcd4_lwmon5 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Dan Malek <dan@embeddedalley.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Remove CONFIG_LWMON5 references.
(Also, remove undefined CONFIG_WD_MAX_RATE while I am here.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tolunay Orkun <torkun@nextio.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
ISBC Key Extension feature is not applicable for RAMBOOT
as there is no way to retrieve the CSF Header and validated
IE Key table from SRAM once CPC has been disabled.
The feature is only applicable in case of NOR SECURE BOOT.
Code Cleanup:
The SECURE_BOOT specific defines have been moved from
arch-ls102xa/config.h to
arm/include/asm/fsl_secure_boot.h
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Recently the FMan Port and MAC compatibles were changed.
This patch aligns the FMan Port and MAC compatibles
to the new FMan device tree binding document.
The FMan device tree binding document can be found in the Linux kernel:
./Documentation/devicetree/bindings/powerpc/fsl/fman.txt
This patch doesn't affect legacy compatibles support.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Tested-by: Xing Lei <xing.lei@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MPC85xx has been using locked L1 cache as init_ram. L1 cache is a write
through cache on E6500. L2 cache is enabled to to hold the data. This
patch locks/unlocks L2 cache to ensure no data cast out from L2 cache.
Signed-off-by: York Sun <yorksun@freescale.com>
Reported-by: Jeffery Zhu <Jefferry.Zhu@freescale.com>
gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Serdes Lanes availability on T4160 and T4080 are same, which serdes 2 & 3
support 8 Lanes, but serdes 1 & 4 support only 4 Lanes E/F/G/H, Lanes
A/B/C/D are not available, updated the serdes table accordingly with
some minor fix.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For running Chain of Trust when doing Secure Boot from NAND,
the Bootscript header and bootscript must be copied from NAND
to RAM(DDR).
The addresses and commands for the same have been defined.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for NAND for P3041.
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In case of secure boot, this default address maps to Boot ROM.
The Boot ROM code requires that the bootloader(U-boot) must lie
in 0 to 3.5G address space i.e. 0x0 - 0xDFFFFFFF.
In case of NAND Secure Boot, CONFIG_SYS_RAMBOOT is enabled and CPC is
configured as SRAM. U-Boot binary will be located on SRAM configured
at address 0xBFF00000.
In the U-Boot code, TLB entries are created to map the virtual address
0xFFF00000 to physical address 0xBFF00000 of CPC configured as SRAM.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Correct the value CONFIG_USB_MAX_CONTROLLER_COUNT macro to 1
for p1025 as it has one USB controller
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MAC1 acts as 1G/10G dual-role MAC on T1024. We introduce
macro SET_FMAN_RX_10G_TYPE2_LIODN for 10G MACs which have
same Port ID and same offset of address with 1G MAC.
Update it to match with the setting of fman in t1024 device
tree, otherwise there is no 'fsl,liodn' in
/proc/device-tree/soc@ffe000000/fman@400000/port@88000/
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
defconfig files are added and SFP version for these platforms
is updated.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The symbolic link to SoC/CPU specific header directory is created
during the build, while it is only necessary for ARM, AVR32, SPARC,
x86, and some CPUs of PowerPC. For the other architectures, it just
results in a broken symbolic link.
Introduce CONFIG_CREATE_ARCH_SYMLINK to not create unneeded symbolic
links.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By making the board selections optional, every defconfig will include
the board selection when running savedefconfig so if a new board is
added to the top of the list of choices the former top's defconfig will
still be correct.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Rini <trini@konsulko.com>
As this board seems to be unmaintained for quite some time, and its
not moved to the generic board ingrastructure, lets remove it.
This will also enable us to remove the CONFIG_AUTOBOOT_DELAY_STR2
and CONFIG_AUTOBOOT_STOP_STR2 macros, as this sc3 board is the
only one using one of this macros. A removal patch will follow
soon.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Juergen Beisert <jbeisert@eurodsn.de>
Acked-by: Heiko Schocher <hs@denx.de>
New QorIQ p1020 based board support from Arcturus Networks Inc.
http://www.arcturusnetworks.com/products/ucp1020/
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
[York Sun: remove patman tags from commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
To replicate:
1. add to include/configs/p1_p2_rdb_pc.h "#define CONFIG_CMD_GPIO"
2. run `make P1020RDB-PC_defconfig`
3. run CROSS_COMPILE=powerpc-linux- make
and you will get:
common/built-in.o: In function `do_gpio':
u-boot/common/cmd_gpio.c:186: undefined reference to `gpio_request'
u-boot/common/cmd_gpio.c:194: undefined reference to `gpio_direction_input'
u-boot/common/cmd_gpio.c:195: undefined reference to `gpio_get_value'
u-boot/common/cmd_gpio.c:200: undefined reference to `gpio_get_value'
u-boot/common/cmd_gpio.c:203: undefined reference to `gpio_direction_output'
u-boot/common/cmd_gpio.c:209: undefined reference to `gpio_free
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The SD clock could be generated by platform clock or peripheral
clock for some platforms. This patch adds peripheral clock
support for T1024/T1040/T2080. To enable it, define
CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Madalin-Cristian Bucur <madalin.bucur@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch defines the 2 flush_dcache_range and invalidate_dcache_range
functions for all the powerpc architecture. Their implementation is
borrowed from the kernel's misc_32.S file and replace the ones from
mpc86xx and ppc4xx since they were equivalent.
This is a fix for the problem introduced by this patch:
http://patchwork.ozlabs.org/patch/448849/
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale PCIe controllers v3.0 and later need to set bit
CFG_READY to allow all inbound configuration transactions
to be processed normally when in EP mode. However, bit
CFG_READY has been moved from PCIe configuration space to
CCSR PCIe configuration register comparing previous version.
The patch is to set this bit according to PCIe version.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for T4240RDB board. SPL
framework is used. PBL initializes the internal RAM and
copies SPL to it. Then SPL initializes DDR using SPD and
copies u-boot from SD card to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: Fix T4240RDB_SDCARD_defcofig]
Reviewed-by: York Sun <yorksun@freescale.com>
Add a delay of 1 microsecond before issuing soft reset to the
controller to let ongoing ULPI transaction complete.
This prevents corruption of ULPI Function Control Register which
eventually prevents phy clock from entering to low power mode
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Commit 96d2bb952b ("powerpc/mpc85xx: Don't relocate exception vectors")
simplified IVOR initialization a bit too much, failing to use the
post-relocation offset. This doesn't cause a problem with normal NOR
boot, in which both the pre-relocation and post-relocation addresses
are 64 KiB aligned. However, if TEXT_BASE is only 4 KiB aligned, such
as for NAND/SD/etc. boot on some targets, as well as the QEMU target,
the post-relocation address will not be the same in the lower 16 bits,
as reserve_uboot() ensures that the relocation address is always 64
KiB aligned even if the pre-relocation address was not.
Use the GOT to get the proper post-relocation offsets.
Fixes: 96d2bb952b ("powerpc/mpc85xx: Don't relocate exception vectors")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Tested-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.
FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The memac for PHY management on little endian SoCs is similar on big
endian SoCs, so we modify the driver by using I/O accessor function to
handle the endianness, so the driver can be reused on little endian
SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian
SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access
is little endian, if not, the I/O access is big endian. Move fsl_memac.h
out of powerpc include.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
1. Default environment will be used for secure boot flow
which can't be edited or saved.
2. Command for secure boot is predefined in the default
environment which will run on autoboot (and autoboot is
the only option allowed in case of secure boot) and it
looks like this:
#define CONFIG_SECBOOT \
"setenv bs_hdraddr 0xe8e00000;" \
"esbc_validate $bs_hdraddr;" \
"source $img_addr;" \
"esbc_halt;"
#endif
3. Boot Script can contain esbc_validate commands and bootm command.
Uboot source command used in default secure boot command will
run the bootscript.
4. Command esbc_halt added to ensure either bootm executes
after validation of images or core should just spin.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-Boot does not have system calls (the services it exposes to
standalone commands use a different mechanism), so the syscall handler
is dead code. It's also broken code, as it assumes it is located at
0xc00 -- while even before the patch to stop relocating exception
vectors to 0, U-Boot had the syscall at 0x900.
The critical and machine check return paths are never called -- the
regular exception return path is used instead, which works because
xSRR0/1 have already been saved and can be restored via the regular
SRR0/1 (we don't care too much in U-Boot about taking a critical/mcheck
inside another exception prolog/epilog).
Also remove a few other small unused functions.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Booke does not require exception vectors to be located at address zero.
U-Boot was doing so anyway, simply because that's how it had been done
on other PPC. The downside of this is that once the OS is loaded to
address zero, the exception vectors have been overwritten -- which
makes it difficult to diagnose a crash that happens after that point.
The IVOR setup and trap entry code is simplified somewhat as a result.
Also, there is no longer a need to align individual exceptions on 0x100
byte boundaries.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch cleans up the names of internal packet buffer names that are
used within the network stack and the functions that use them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
As mentioned in the previous commit, adding default values in each
Kconfig causes problems because it does not co-exist with the
"depends on" syntax. (Please note this is not a bug of Kconfig.)
We should not do so unless we have a special reason. Actually,
for CONFIG_DM*, we have no good reason to do so.
Generally, CONFIG_DM is not a user-configurable option. Once we
convert a driver into Driver Model, the board only works with Driver
Model, i.e. CONFIG_DM must be always enabled for that board.
So, using "select DM" is more suitable rather than allowing users to
modify it. Another good thing is, Kconfig warns unmet dependencies
for "select" syntax, so we easily notice bugs.
Actually, CONFIG_DM and other related options have been added
without consistency: some into arch/*/Kconfig, some into
board/*/Kconfig, and some into configs/*_defconfig.
This commit prefers "select" and cleans up the following issues.
[1] Never use "CONFIG_DM=n" in defconfig files
It is really rare to add "CONFIG_FOO=n" to disable CONFIG options.
It is more common to use "# CONFIG_FOO is not set". But here, we
do not even have to do it.
Less than half of OMAP3 boards have been converted to Driver Model.
Adding the default values to arch/arm/cpu/armv7/omap3/Kconfig is
weird. Instead, add "select DM" only to appropriate boards, which
eventually eliminates "CONFIG_DM=n", etc.
[2] Delete redundant CONFIGs
Sandbox sets CONFIG_DM in arch/sandbox/Kconfig and defines it again
in configs/sandbox_defconfig.
Likewise, OMAP3 sets CONFIG_DM arch/arm/cpu/armv7/omap3/Kconfig and
defines it also in omap3_beagle_defconfig and devkit8000_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This value is not used by the network stack and is available in the
global data, so stop passing it around. For the one legacy function
that still expects it (init op on old Ethernet drivers) pass in the
global pointer version directly to avoid changing that interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Trival fix to remove an unneeded variable declaration in 4xx_enet.c)
The current implementation exposes the eth_device struct to code that
needs to access the MAC address. Add a wrapper function for this to
abstract away the pointer for this operation.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the option to Kconfig renaming it to CONFIG_HAVE_GENERIC_BOARD.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Larry Johnson <lrj@acm.org>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Eric Millbrandt <emillbrandt@dekaresearch.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Erik Theisen <etheisen@mindspring.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stephen Williams <steve@icarus.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
esbc_validate command uses various IP Blocks: Security Monitor, CAAM block
and SFP registers. Hence the respective CONFIG's are enabled.
Apart from these CONFIG_SHA_PROG_HW_ACCEL and CONFIG_RSA are also enabled.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale sfp has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the CCSR defintion of
sfp_regs to common include. This patch also defines ccsr_sfp_regs
definition for newer versions of SFP.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Modify CONFIG_USB_MAX_CONTROLLER_COUNT value to 1 on P1022DS.
As ETSEC2 and USB2 are muxed; thus if ETSEC2 is enabled, the
system bus hangs on USB2 if ETSEC2 is enabled but "usb start"
command is issued. Hence making default controller count to 1
to avoid system hang.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: Yusong Sun <yorksun@freescale.com>
The code provides framework for heterogeneous multicore chips based on StarCore
and Power Architecture which are chasis-2 compliant, like B4860 and B4420
It will make u-boot recognize all non-ppc cores and peripherals like
SC3900/DSP CPUs, MAPLE, CPRI and print their configuration in u-boot logs.
Example boot logs of B4860QDS:
U-Boot 2015.01-00232-geef6e36-dirty (Jan 19 2015 - 11:58:45)
CPU0: B4860E, Version: 2.2, (0x86880022)
Core: e6500, Version: 2.0, (0x80400120)
Clock Configuration:
CPU0:1600 MHz, CPU1:1600 MHz, CPU2:1600 MHz, CPU3:1600 MHz,
DSP CPU0:1200 MHz, DSP CPU1:1200 MHz, DSP CPU2:1200 MHz, DSP CPU3:1200 MHz,
DSP CPU4:1200 MHz, DSP CPU5:1200 MHz,
CCB:666.667 MHz,
DDR:933.333 MHz (1866.667 MT/s data rate) (Asynchronous), IFC:166.667 MHz
CPRI:600 MHz
MAPLE:600 MHz, MAPLE-ULB:800 MHz, MAPLE-eTVPE:1000 MHz
FMAN1: 666.667 MHz
QMAN: 333.333 MHz
Top level changes include:
(1) Top level CONFIG to identify HETEROGENUOUS clusters
(2) CONFIGS for SC3900/DSP components
(3) Global structures like "cpu_type" and "MPC85xx_SYS_INFO"
updated for dsp cores and other components
(3) APIs to get DSP num cores and their Mask like:
cpu_dsp_mask, cpu_num_dspcores etc same as that of PowerPC
(5) Code to fetch and print SC cores and other heterogenous
device's frequencies
(6) README added for the same
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Introduce arch_reserve_stacks() to tailor gd->start_addr_sp and gd->irq_sp to
the architecture needs.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These additional nodes need to be provided to get U-Boot to boot correctly
on the Canyonlands / Glacier board:
- chosen path to the console-uart
- reg-shift set to 0 in the uart device nodes
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Define an _end symbol indicating the end of u-boot.bin. Also add some dummy
words into the link script to ensure that u-boot.bin will always extend
that far. There may be a better way of doing this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is required at present for device tree control. The ppc4xx does support
GPIOs but does not seem to have a proper driver. So this file is empty.
Signed-off-by: Simon Glass <sjg@chromium.org>
The canyonlands.h config file works with canyonlands, glacier and arches
boards. Bring in the device tree files for these from Linux 3.17.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new ramboot config for glacier so that it is possible to test U-Boot
loaded over Ethernet instead of using JTAG.
Signed-off-by: Simon Glass <sjg@chromium.org>
Many CONFIG options have an unnecessary value of 1. CONFIG_440 is set in
the various board config files. Also simplify the CONFIG_440 check in
config.mk
Signed-off-by: Simon Glass <sjg@chromium.org>
Era property is added in the crypto node in device tree.
Move the code to do so from arch/powerpc/mpc8xxx/fdt.c to
drivers/sec/sec.c so that it can be used across arm and
powerpc platforms having crypto node.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
[York Sun: Fix commit message indentation]
Reviewed-by: York Sun <yorksun@freescale.com>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
These boards are still non-generic boards.
It is a good thing that we can drop board-specific hack code
from drivers/mtd/nand/nand_base.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Andrea "llandre" Marson <andrea.marson@dave-tech.it>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
This patch initializes VSC9953 L2 Switch for boards that have
CONFIG_VSC9953 defined in their config file.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Some Freescale SoCs like T1020 and T1040 have an integrated
L2 Switch. The L2 Switch ports may be connected to Ethernet PHYs
over SGMII and QSGMII.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The number of supported serdes protocols on Freescale SoCs
has increased over time. Until now, an u64 variable have been
initialized on boot with the configured protocols. However,
since this number has increased (enum srds_prtcl has more
than 64 values), 64 bits are no longer sufficient to hold track
of all the configured protocols.
This patch replaces the u64 map values with static arrays.
To keep track of the number of serdes protocols, the
SERDES_PRCTL_COUNT vale has been added at the end of
enum srds_prtcl. This value must always be the last one.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
All the boards that support deep sleep feature are converted
to deep sleep generic board interface. The old interface which
support non-generic board is not used anymore. So clean it up.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_SYS_PBI_FLASH_BASE is defined for Secure Boot on C29X
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For B4 the LIODN register for PCIe is in PCIe address space and not in
GUTs
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. As a result, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h>.
The right fix would be to split the lib/fdtdec.c to remove
dependency on GPIO.
This commit adds a dummy <asm/arch/gpio.h> to support OF_CONTROL
for mpc85xx platform. A file mpc85xx_gpio.h exists in
arch/powerpc/include/asm. The defintions in that file conflict
with the ones in asm-generic/gpio.h. Hence a dummy header file
has been added. This will be removed after FDT-GPIO stuff is
fixed correctly.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Now TQM8xx is the only remaining board family of mpc8xx.
It uses its own linker script, board/tqc/tqm8xx/u-boot.lds.
arch/powerpc/cpu/mpc8xx/u-boot.lds is not used by any boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Since commit 843125daeb (ppc4xx: remove HH405 board), CONFIG_HH405
is not defined.
Since commit d526330479 (ppc4xx: remove PMC405), CONFIG_PMC405
is not defined.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
All the MPC824X boards are still non-generic boards:
A3000, CPC45, CU824, eXalion, MVBLUE, MUSENKI, Sandpoint824x, utx8245
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Torsten Demke <torsten.demke@fci.com>
Cc: Jim Thompson <jim@musenki.com>
Cc: Greg Allen <gallen@arlut.utexas.edu>
These boards are still non-generic boards.
drivers/rtc/ds12887.c should also be removed because it can not
be built without CONFIG_ATC.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
This board is still a non-generic board.
Unused code in arch/powerpc/cpu/mpc8xx/video.c should be also deleted
because CONFIG_VIDEO_ENCODER_AD7176, CONFIG_VIDEO_ENCODER_AD7177,
CONFIG_VIDEO_ENCODER_AD7179 are not defined any more.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Not all portals might be managed and therefore visible.
Set the isdr register so that the corresponding isr register
won't be set. This is required when supporting power management.
Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Commit f29f804a93 generalized the TLB
mapping function, but made the DDR mapping leftover size to zero,
causing the message not printed.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alexander Graf <agraf@suse.de>
CC: Scott Wood <scottwood@freescale.com>
move usb device tree fixup code from "arch/powerpc/" to "drivers/usb/"
so that it works independent of architecture it is running on
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Introduce a Makefile under arch/$ARCH/ and include it in the
top Makefile (similar to Linux kernel). This allows further
refactoringi like moving architecture-specific code out of global
makefiles, deprecating config variables (CPU, CPUDIR, SOC) or
deprecating arch/$ARCH/config.mk.
In contrary to Linux kernel, U-Boot defines the ARCH variable by
Kconfig, thus the arch Makefile can only included conditionally
after the top config.mk.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This board sprinkles #ifdef(CONFIG_HERMES) over various global files
such as include/common.h, common/board_r.c, common/cmd_bdinfo.c.
Let's zap such an ill-behaved board.
It has not been converted to generic board yet and mpc8xx is old
enough.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Newer qoriq socs have an updated dma ip block with a
different compatible. Let's make sure we use the proper
string so that the dmas get their liodn.
In order to have the means to specify the compatible
string, the liodn setting macros were updated to receive
a new parameter for it.
The following SoCs were changed to use the new compatible:
T1023/4, T1040, T2080/1, T4240, B4860.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increase IO drive strength to fix FCS error on RGMII ports
on T1024QDS.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER.
but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs.
on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
10GEC1->MAC1, 10GEC2->MAC2
so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on
which 10GEC enumeration is consistent with MAC enumeration.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Freescale T1024/T1023 SoC.
The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
- Three PCI Express 2.0 controllers
- Additional peripheral interfaces
- One SATA 2.0 controller
- Two USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/eSDHC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T1024 and T1023:
Feature T1024 T1023
QUICC Engine: yes no
DIU: yes no
Deep Sleep: yes no
I2C controller: 4 3
DDR: 64-bit 32-bit
IFC: 32-bit 28-bit
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.
A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 v1.0 has this errata while v1.1 has fixed
this errata by hardware, add a new function has_errata_a007186
to check the SVR_SOC_VER, SVR_MAJ and SVR_MIN first,
if the sil has errata a007186, then run the errata code,
if not, doesn't run the code.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Workaround of Errata A-008044 was implemented without errata number and it is
enabled by default. Errata A-008044 is only valid for T1040 Rev 1.0.
So put errata number and make it conditional.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.
Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 rev 1.1 changes MEM_RAT in RCW, which requires new parsing for ratio,
the same way as T4240 rev 2.0.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
Move USB Errata checking code from "arch/powerpc" to architecture independent
file "fsl_usb.h" so that errata(s) become independent of the architecture.
For each erratum checking function for PPC arch, define a nop function for
non PPC arch for successful compilation in either case
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.
Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.
Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
U-Boot has imported various utility macros from Linux
scattering them to various places without consistency.
In include/common.h are min, max, min3, max3, ARRAY_SIZE, ALIGN,
container_of, DIV_ROUND_UP, etc.
In include/linux/compat.h are min_t, max_t, round_up, round_down,
etc.
We also have duplicated defines of min_t in some *.c files.
Moreover, we are suffering from too cluttered include/common.h.
This commit moves various macros that originate in
include/linux/kernel.h of Linux to their original position.
Note:
This commit simply moves the macros; the macros roundup,
min, max, min2, max3, ARRAY_SIZE are different
from those of Linux at this point.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
As auto-negotiation is not supported for 2.5G SGMII, we need
to add a new type PHY_INTERFACE_MODE_SGMII_2500 to differentiate
SGMII-1G and SGMII-2.5G with different setting for auto-negotiation.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When an MPC5200 based board is used with SPL support, the main
U-Boot needs to clear the GD (global data) struct again.
Otherwise the generic board init code in board_init_f (when
CONFIG_SYS_GENERIC_BOARD is defined) will not initialize all
GD variables correctly. Resulting in a hangup on the a4m2k
board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The gdsys hrcon board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x GbE (optional)
- Lattice ECP3 FPGA connected via eLBC and PCIe
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The argument boot_flags of board_init_f() is not used at all in the
powerpc specific board.c init sequence. Now with the generic init
sequence, this boot_flags arg is used by board_init_f().
This patch sets the r3 register that is used to pass the boot_flags
argument from the start.S board_init_f() call to 0 prior to the function
call to avoid unknown content to end up in gd->flags.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
IFC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of IFC IP.
So use IFC acessor functions instead of in_be32().
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LIODN entry for B4860/B4420 mentions USB controller as "mph"
insread of "dr". This results in PAMU not permitting bus
transactions for USB DR controller on B4860 resulting in
USB function failure. Replacing "fsl-usb2-mph" with
"fsl-usb2-dr" allows USB DR controller bus transactions
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: Sethi Varun-B16395 <Varun.Sethi@freescale.com>
Reviewed-by: Sun Yusong-R58495 <yorksun@freescale.com>
NEG bit default is '1' for external MDIOs as per FMAN-v3 RM, but on some
platforms, e.g. T2080QDS, this bit is '0', which leads to MDIO failure
on XAUI PHY, so set this bit definitely to align with the RM.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. use Payload length check disable when enable MAC;
2. add XGMII support for setting MAC interface mode;
3. only enable auto negotiation for Non-XGMII mode;
4. return 0xffff if clause 22 is used to read 10G phy_id;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-By: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
mcc200 and prs200 are old and have no maintainer. Remove the boards.
This also removes the mcc200 specific 1bpp BMP support from
common/lcd.c
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
ppc4xx i2c master gets stuck on errors while repeated start is
active. Can be easily reproduced by "i2c md" on an unpopulated
i2c address. There is not stop condition given, scl remains
pulled low.
The only way out seems to be doing a stop manually and then a
soft reset.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
There are a number of places where U-Boot intentionally and legally
accesses physical address 0x0000, for example when installing
exception vectors on systems where these are located in low memory.
Add "cppcheck-suppress nullPointer" comments to silence cppcheck
where this is intentional and legal.
Signed-off-by: Wolfgang Denk <wd@denx.de>
I realized that with v2014.10 u-boot is not starting up on
ppc4xx boards with CONFIG_SYS_GENERIC_BOARD set.
I bisected it down to this:
d54d7eb support blackfin board initialization in generic board_f
With
d29437a ppc: Make ppc4xx ready for CONFIG_SYS_GENERIC_BOARD
I set gd to a defined value for ppc4xx in cpu_init_f().
I did not realize that the gd struct has also to be memset()
to zero at this point.
But at least commit d54d7eb assumes it is:
@@ -516,11 +528,13 @@ static int reserve_malloc(void)
/* (permanently) allocate a Board Info struct */
static int reserve_board(void)
{
- gd->start_addr_sp -= sizeof(bd_t);
- gd->bd = (bd_t *)map_sysmem(gd->start_addr_sp, sizeof(bd_t));
- memset(gd->bd, '\0', sizeof(bd_t));
- debug("Reserving %zu Bytes for Board Info at: %08lx\n",
- sizeof(bd_t), gd->start_addr_sp);
+ if (!gd->bd) {
+ gd->start_addr_sp -= sizeof(bd_t);
+ gd->bd = (bd_t *)map_sysmem(gd->start_addr_sp, sizeof(bd_t));
+ memset(gd->bd, '\0', sizeof(bd_t));
+ debug("Reserving %zu Bytes for Board Info at: %08lx\n",
+ sizeof(bd_t), gd->start_addr_sp);
+ }
return 0;
}
#endif
This might also be an issue on other architectures, so maintainers should
check.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit d58a9451e7 (ppc/arm: zap EMK boards) removed
TOP* boards support but missed to remove entries in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
The following bard configurations have been without active maintenance
for a long time, and the board maintainer agrees to have them removed:
MPC5200: TOP5200, MINI5200, EVAL5200
MPC860: TOP860
at91sam9xeXXX: top9000eval_xe, top9000su_xe
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
[trini: Add missing Kconfig removals]
Signed-off-by: Tom Rini <trini@ti.com>
CONFIG_TPL should not be enabled for boards that do not have TPL.
CONFIG_SUPPORT_TPL introduced by this commit should be "select"ed
by boards with TPL support and CONFIG_TPL should depend on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_SPL should not be enabled for boards that do not have SPL.
CONFIG_SUPPORT_SPL introduced by this commit should be "select"ed
by boards with SPL support and CONFIG_SPL should depend on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This is the only used of CONFIG_SPI_X macro, just zap this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Remove this board as this is the only one last user of eeprom_probe(),
which is pretty non-standard stuff.
This patch also removes all the PHP, SQL and CSS stuff from U-Boot,
which probably makes U-Boot a bit less IoT ;-)
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board uses eeprom accessors in an incorrect way. The board
is old and unsupported, just zap it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is the only user of CONFIG_SYS_EEPROM_X40430 , remove
it so the EEPROM command code can be cleansed of the related code
as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
The file board/Marvell/include/mv_gen_reg.h is incompatible with
the GPL (see for example the "MARVELL RESERVES THE RIGHT AT ITS SOLE
DISCRETION TO REQUEST THAT THIS CODE BE IMMEDIATELY RETURNED TO
MARVELL" clause). As this cannot be fixed, we remove the file and all
code that depends on it. Fortunately this only affects some very old
boards that have long reached EOL:
CPCI750
DB64360
DB64460
p3m750
p3m7448
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Commit d6b11fd1 (powerpc: remove MBX and MBX860T boards support)
removed mbxbar field in "struct sysconf512x" by mistake and broke
booting on mpc5121 boards. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
By default, PAMU's (IOMMU) are enabled in case of secure boot.
Disable/bypass them once the control reaches the bootloader.
For non-secure boot, PAMU's are already bypassed in the default
SoC configuration.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SHA-256 and SHA-1 accelerated using SEC hardware in Freescale SoC's
The driver for SEC (CAAM) IP is based on linux drivers/crypto/caam.
The platforms needto add the MACRO CONFIG_FSL_CAAM inorder to
enable initialization of this hardware IP.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SEC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of SEC IP.
So update acessor functions with common SEC acessor functions to take care
both type of endianness.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale SEC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the CCSR defintion of
SEC to common include
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board has been orphaned for more than 6 months.
It is the last board defining CONFIG_APM821XX.
The code inside #ifdef CONFIG_APM821XX should be removed too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
With some versions of gcc (that we know of 4.6.3 and 4.8.2 are affected)
it is necessary to specify --bss-plt to get the final blrl in the
_GOT2_TABLE_. Without this the last symbol does not get it's address
relocated. For the P2041RDB board this ended up being
NetArpWaitTimerStart which caused the ARP packets to timeout
immediately.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-boot has been initializing DDR for the main memory. The presumption
is the memory stays as a big continuous block, either linear or
interleaved. This change is to support putting some DDR controllers
to separated space without counting into main memory. The standalone
memory controller could use different number of DIMM slots.
Signed-off-by: York Sun <yorksun@freescale.com>
Each CPU of PowerPC has its default linker script under the CPU
directory, except mpc8xx.
Every mpc8xx board has its own linker script under the board
directory, resulting in lots of duplication of linker scripts.
I notice eight mpc8xx boards have the same linker script.
We can decrease the number of linker scripts by putting a single
default linker script, arch/powerpc/cpu/mpc8xx/u-boot.lds.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
"0x00" is a valid serdes protocol for QorIQ parts, and can not be
used to test whether the serdes is enabled or disabled.
Signed-off-by: Ebony Zhu <b45385@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Fix following issues in USB device-tree fixup:
- returns when either dr_mode or phy_type not defined.
This was terminating fix-up when only either property
was defined in hwconfig string
- updates dr_mode_type or dr_phy_type with junk value when
their index is -1. Now these are updated only when their
respective index is pointing to relevant types
in modes[] and phys[] array
- dr_mode_type and dr_phy_type were not NULL for
each controller
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
fsl_enet.h defines the mapping of the usual MII management
registers, which are included in the MDIO register block
common to Freescale ethernet controllers. So it shouldn't
depend on the CPU architecture but it should be actually
part of the arch independent fsl_mdio.h.
To remove the arch dependency, merge the content of
asm/fsl_enet.h into fsl_mdio.h.
Some files (like fm_eth.h) were simply including fsl_enet.h
only for phy.h. These were updated to include phy.h instead.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Some drivers (e.g. net/e1000) reference these functions. So, this
fixes the build of MVBC_P board.
I'm not familiar with the MPC5xxx platform, maybe a full
implementation shall be implemented instead of this stub in the
future.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>, Marek Vasut <marex@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
If hwconfig does not contains "en_cpc" then by default all cpcs are enabled
If this config is defined then only those individual cpcs which are defined
in the subargument of "en_cpc" will be enabled e.g en_cpc:cpc1,cpc2; (this
will enable cpc1 and cpc2) or en_cpc:cpc2; (this enables just cpc2)
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add deep sleep support in SPI/SD boot. The destination address
second stage uboot image is loaded to is changed because
currently this address will be used by kernel which means
we can't reserve it for resume.
Entry point to kernel is still placed in second stage uboot.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
bootflag as a parameter is passed to board_init_f().
But it is not actually used in this function.
Make it effective by assigned it to gd->flags.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When CONFIG_WATCHDOG is defined the board initialization just performs
a WATCHDOG_RESET, an initialization of the watchdog is not done.
This has been modified fot the MPC85xx, the board initialization calls
its watchdog initialitzation allowing for full watchdog configuration
very early in the boot phase.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Function to inititialize the cpu watchdog added.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
[York Sun: Add prototype in watchdog.h]
Reviewed-by: York Sun <yorksun@freescale.com>
For e500mc cores the watchdog timer period has to be set by means of a
6bit value, that defines the bit of the timebase counter used to signal
a watchdog timer exception on its 0 to 1 transition.
The macro used to set the watchdog period TCR_WP, was redefined for e500mc
to support 6 WP setting.
The parameter (x) given to the macro specifies the prescaling factor of
the time base clock (fTB):
watchdog_period = 1/fTB * 2^x
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
TCR watchdog bit are overwritten when dec interrupt is enabled.
This has been fixed with this patch.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_${CPU} is defined by Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
This commit enables Kconfig.
Going forward, we use Kconfig for the board configuration.
mkconfig will never be used. Nor will include/config.mk be generated.
Kconfig must be adjusted for U-Boot because our situation is
a little more complicated than Linux Kernel.
We have to generate multiple boot images (Normal, SPL, TPL)
from one source tree.
Each image needs its own configuration input.
Usage:
Run "make <board>_defconfig" to do the board configuration.
It will create the .config file and additionally spl/.config, tpl/.config
if SPL, TPL is enabled, respectively.
You can use "make config", "make menuconfig" etc. to create
a new .config or modify the existing one.
Use "make spl/config", "make spl/menuconfig" etc. for spl/.config
and do likewise for tpl/.config file.
The generic syntax of configuration targets for SPL, TPL is:
<target_image>/<config_command>
Here, <target_image> is either 'spl' or 'tpl'
<config_command> is 'config', 'menuconfig', 'xconfig', etc.
When the configuration is done, run "make".
(Or "make <board>_defconfig all" will do the configuration and build
in one time.)
For futher information of how Kconfig works in U-Boot,
please read the comment block of scripts/multiconfig.py.
By the way, there is another item worth remarking here:
coexistence of Kconfig and board herder files.
Prior to Kconfig, we used C headers to define a set of configs.
We expect a very long term to migrate from C headers to Kconfig.
Two different infractructure must coexist in the interim.
In our former configuration scheme, include/autoconf.mk was generated
for use in makefiles.
It is still generated under include/, spl/include/, tpl/include/ directory
for the Normal, SPL, TPL image, respectively.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The generic board infrastructure assumes that gd is set by
arch code.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
When resume from deep sleep, uboot needs to enable L2 and CPC
cache, or they would be keeping unusable in kernel because
kernel didn't enble or initialized them.
This patch didn't change the existing L2 cache enabling code,
just put them in a function.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T4240 has 4 serdes, each serdes has 4k memory space, two PLLs.
We use PLL1CR0 to check the serdes reference clock.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
ls1021 is arm-core and supports qe too.
Move immap_qe.h into common directory for both arm and powerpc.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On some SoC(e.g. T2080/T4240) the 3rd DMA is not functional if SRIO2 is
chosen. we add fdt_fixup_dma3() to disable the 3rd DMA if SRIO2 is chosen.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since ARRAY_SIZE macro is defined in include/common.h,
re-defining it in arch-specific files is redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Remove the common infrastructure of nand_spl and
clean-up the code inside ifdef(CONFIG_NAND_U_BOOT)..endif.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This is a workaround for 32 bit hardware limitation of TDM.
T1040 has 36 bit physical addressing, TDM DMAC register
are 32 bit wide but need to store address of CCSR space
which lies beyond 32 bit address range. This workaround
creats a LAW to enable access of TDM DMA to CCSR by
mapping CCSR to overlap with DDR.
A hole of 16M is created in memory using device tree. This
workaround law is set only if "tdm" is defined in hwconfig.
Also disable POST tests and add LIODN for TDM
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes PLL is calibrated at reset. When the junction temperature
delta from the time the PLL is calibrated exceeds +56C/-66C,
jitter may increase and can cause PLL to unlock.
This workaround overwrite the SerDes registers with new values,
to calibrate SerDes registers.
These values are known to work fine for all temperature ranges.
This workaround is valid for B4, T4 and T2 platforms, so
added in their config.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
[York Sun: replaced typedef ccsr_sfp_regs_t with struct ccsr_sfp_regs]
Reviewed-by: York Sun <yorksun@freescale.com>
When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.
Signed-off-by: York Sun <yorksun@freescale.com>
A-007186: SerDes PLL is calibrated at reset. It is possible for jitter to
increase and cause the PLL to unlock when the temperature delta from the
time the PLL is calibrated exceeds +56C/-66C when using X VDD of 1.35 V
(or +70C/-80C when using XnVDD of 1.5 V). No issues are seen with LC
VCO. Only the protocols using Ring VCOs are impacted.
Workaround:
For all 1.25/2.5/5 GHz protocols, use LC VCO instead of Ring VCO, this need
to use alternate serdes protocols. The alternate option has the same
functionality as the original option; the only difference being LC VCO
rather than Ring VCO.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As errata A-007186, we need to use the alternate serdes
protocol instead of those impacted protocols.
- add support for serdes protocols: 0x1b, 0x50, 0x5e,
0x64, 0x6a, 0xd2, 0x67, 0x70.
- update t2080_rcw.cfg to adapt to new rcw_66_15 for
t2080qds and t2080rdb.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This code seems unnecessarily complex. We really just need to check the
global_data. Now that is it all in one place, and not arch-specific, this
is pretty easy.
Signed-off-by: Simon Glass <sjg@chromium.org>
P1020 SoC which has two USB controllers, but only first one is used
on this platform.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4460 differs from B4860 only in number of CPU cores,
hence used existing support for B4860.
B4460 has 2 PPC cores whereas B4860 has 4 PPC cores.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
By default, all PEX inbound windows PEX_PEXIWARn[TRGT] are
mapped to 0xF, which is local memory. But for BSC9132, 0xF
is CCSR, 0x0 is local memory.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The argument boot_flag of board_inti_f() hasn't been used for powerpc until
recent changing to use generic board. Set it to 0 as a proper value.
Signed-off-by: York Sun <yorksun@freescale.com>
baord_init_f takes one argument, boot_flag. It has not been used for
powerpc, until recently changing to use generic board architecture.
The boot flag is added as a return value from cpu_init_f().
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alexander Graf <agraf@suse.de>
The pointer of device tree comes from r3 for QEMU. This is not the case
for normal SoCs out of reset. Having gd->fdt_blob as 0 is important for
other functions to detect the non-existence of device tree.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alexander Graf <agraf@suse.de>
We want to use the TLB mapping helpers in relocated mode as well. These helpers
need to have awareness of already occupied TLB entries. We already had them in
sync in non-relocated mode, but need to resync them when we move into relocated.
Signed-off-by: Alexander Graf <agraf@suse.de>
For the QEMU machine type, we can plug in either e500v2, e500mc, e5500
or e6500 style cores into the system. U-boot has to work with all of them.
So avoid using HID1 which is not available on e500mc systems to make sure
we don't trap on it.
Signed-off-by: Alexander Graf <agraf@suse.de>
We only need u-boot to bother about a single core in the QEMU machine.
Everything that would require additional knowledge of more cores gets
handled by QEMU and passed straight into the payload we execute.
Because of this setup, it would be counterproductive to enable SMP support
in u-boot. We would have to rip CPUs out of already existing spin tables
and respin them from u-boot. It would be a pretty big mess.
So only assume we have a single core. This fixes errors about CONFIG_MP
being disabled.
Signed-off-by: Alexander Graf <agraf@suse.de>
The T4080 SoC is a low-power version of the T4160.
T4080 combines 4 dual-threaded Power Architecture e6500
cores with single cluster and two memory complexes.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Secure Boot Target is added for T2080RDB
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T2080RDB.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
T1040RDB.h file is removed and a unified file T104xRDB.h is created.
Hence macro CONFIG_T1040 is renamed to CONFIG_T104x.
Signed-off-by: Gaurav Kumar Rana <gaurav.rana@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
CONFIG_BOARDDIR is not referenced in these linker scripts.
The comment /* CONFIG_BOARDDIR */ is misleading.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
mpc831x has no muram, so muram cannot be used for bootcounter
function.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
B4420 is a personality of B4860.
It should have same FM1_CLK_SEK and FM1_CLK_SHIFT as B4860
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Adds support for clock sourcing from sysclk(100MHz) for usb
on T104xRDB and T1040QDS. This requires changing reference divisor
and multiplication factor to derive usb clock from sysclk.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040 and it's variants provide "Single Oscillator Source" Reference Clock Mode.
In this mode, single onboard oscillator(DIFF_SYSCLK) can provide the reference clock
(100MHz) to the following PLLs:
• Platform PLL
• Core PLLs
• USB PLL
• DDR PLL, etc
The cfg_eng_use0 of porsr1 register identifies whether the SYSCLK (single-ended) or
DIFF_SYSCLK (differential) is selected as the clock input to the chip.
get_sys_info has been enhanced to add the diff_sysclk so that the
various drivers can be made aware of ths diff sysclk configuration and
act accordingly.
Other changes:
-single_src to ddr_refclk_sel, as it is use for checking ddr reference clock
-Removed the print of single_src from get_sys_info as this will be
-printed whenever somebody calls get_sys_info which is not appropriate.
-Add print of single_src in checkcpu as it is called only once during initialization
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
It is not necessary for bootpg to be present at text + 512KB.
With increase of u-boot size (768KB), bootpg section's address
cannot be fixed.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Before parsing LAW table i.e. init_law, boot loader should disable all
previous LAWs except DDR LAWs which has been created by previous
pre boot loader during DDR initialization.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Current SPL code base has BSS section placed after reset_vector. This means
they have to relocate to use the global variables. This put an implicit
requirement of having SPL size = Memory/2.
To avoid relocation:
- Move bss_section within SPL range
- Modify relocate_code()
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SPL linker has fix location of bootpg and reset vector with respect to text base.
It is not necessary to have fixed locations.
Avoid such hardcoding.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LAW_EN is only defined if CONFIG_SYS_CCSRBAR_DEFAULT is not equal to
CONFIG_SYS_CCSRBAR_PHYS. in SPL framework CCSRBAR is not relocated hence
both are same. This cause compilation error.
So LAW_EN define outside of configs
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
qe_init() does not use data copied from NAND. Thise code is not tested or
complied causing compilation error during NAND boot
So, remove QE firmware copy from NAND to ddr.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When T104x soc wakes up from deep sleep, control is passed to the
primary core that starts executing uboot. After re-initialized some
IP blocks, like DDRC, kernel will take responsibility to continue
to restore environment it leaves before.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The supplement configuration unit (SCFG) provides chip-specific
configuration and status registers for the device. It is the chip
defined module for extending the device configuration unit (DCFG)
module. It provides a set of CCSR registers in addition to those
available in the device configuration unit.
The base address for this unit is 0x0F_C000.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040RDB and T1040QDS boards have an integrated l2 switch.
The switch needs a MAC address for Layer 2 protocols
(MSTP, LLDP, LACP, etc). Setting a MAC address on l2switchaddr will add
a MAC in device-tree, under node l2switch.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Erratum A007212 for DDR is about a runaway condition for DDR PLL
oscilliator. Please refer to erratum document for detail.
For this workaround to work, DDR PLL needs to be disabled in RCW.
However, u-boot needs to know the expected PLL ratio. We put the
ratio in a reserved field RCW[18:23]. U-boot will skip this workaround
if DDR PLL ratio is set, or the reserved field is not set.
Workaround for erratum A007212 applies to selected versions of
B4/T4 SoCs. It is safe to apply the workaround to all versions. It
is helpful for upgrading SoC without changing u-boot. In case DDR
PLL is disabled by RCW (part of the erratum workaround), we need this
u-boot workround to bring up DDR clock.
Signed-off-by: York Sun <yorksun@freescale.com>
Put a delay of 5 millisecond after reset so that ULPI phy
gets enough time to come out of reset. Erratum A007075 applies
to following SOCs and their variants, if any
P1010 rev 1.0
B4860 rev 1.0, 2.0
P4080 rev 2.0, 3.0
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The value written to L2CSR1 didn't match the value written to the
device tree.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Modify code to adapt to both u-qe and qe.
U_QE is a kind of cutted QE.
the differences between U_QE and QE
1. UCC: U_QE supports 2 UCCs while QE supports up to 8 UCCs.
2. IMMR: have different immr base addr.
3. iopin: U_QE doesn't need to config iopin.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for T1040QDS and T1040RDB
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T1040QDS and
CONFIG_T1040RDB
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for T2080QDS
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T2080QDS.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for T4240QDS and T4160QDS
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T4240QDS.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Changes:
1. L2 cache is being invalidated by Boot ROM code for e6500 core.
So removing the invalidation from start.S
2. Clear the LAW and corresponding configuration for CPC. Boot ROM
code uses it as hosekeeping area.
3. For Secure boot, CPC is configured as SRAM and used as house
keeping area. This configuration is to be disabled once in uboot.
Earlier this disabling of CPC as SRAM was happening in cpu_init_r.
As a result cache invalidation function was getting skipped in
case CPC is configured as SRAM.This was causing random crashes.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add NOR, SPI and SD secure boot targets for BSC9132QDS.
Changes:
- Debug TLB entry is not required for Secure Boot Target.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ISBC creates a LAW 0 entry for non PBL platforms, which is not
disabled before transferring the control to uboot.
The LAW 0 entry has to be disabled.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For KVM we have a special PV machine type called "ppce500". This machine
is inspired by the MPC8544DS board, but implements a lot less features
than that one.
It also provides more PCI slots and is supposed to be enumerated by
device tree only.
This patch adds support for the generic ppce500 machine and tries to
rely solely on device tree for device enumeration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We want to be able to directly execute the ELF binary without going
through the u-boot.bin one.
To know where we have to start executing this ELF binary we have to
tell the linker where our entry point is.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The DDR mapping function really is just a generic virtual -> physical
mapping function. Generalize it so it can support any virtual starting
offset and IO maps just the same.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There is no need to set IVORs to anything but their default values,
so let's leave them where they are.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
[York Sun: Add back $(obj)start.S section in mpc8572ds/Makefile]
Reviewed-by: York Sun <yorksun@freescale.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/mousse/*
- Remove include/configs/MOUSSE.h
- Clean-up defined(CONFIG_MOUSSE)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/RPXlite/*
- Remove board/RPXClassic/*
- Remove include/configs/RPXlite.h
- Remove include/configs/RPXClassic.h
- Clean-up defined(CONFIG_RPXCLASSIC)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove include/configs/{ADS860.h,FADS823.h,FADS850SAR.h,FADS860T.h}
- Cleanup defined(CONFIG_ADS), defined(CONFIG_MPC823FADS),
defined(CONFIG_MPC850SAR), defined(CONFIG_SYS_DAUGHTERBOARD)
- Remove the entries from boards.cfg
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/mbx8xx/*
- Remove include/configs/{MBX.h,MBX860T.h}
- Clean-up if defined(CONFIG_MBX)
- Move the entries from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/nx823/*
- Remove include/configs/NX823.h
- Clean-up ifdef(CONFIG_NX823)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
References to the wireless keyboard should also be removed
from README.console.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
1. The Data timeout counter value in eSDHC_SYSCTL register is
not working as it should be, so add quirks to enable this
workaround to fix it to the max value 0xE.
2. Add CONFIG_SYS_FSL_ERRATUM_ESDHC111 to enable its workaround.
* Update of patch for change mmc interface by
Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Prior to Kbuild, $(OBJTREE) was used for pointing to the
top of build directory with absolute path.
In Kbuild style, $(objtree) is used instead.
This commit renames OBJTREE to objtree and delete the
defition of OBJTREE.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Prior to Kbuild, $(TOPDIR) or $(SRCTREE) was used for
pointing to the top of source directory.
(No difference between the two.)
In Kbuild style, $(srctree) is used instead.
This commit renames TOPDIR to srctree and delete the
defition of TOPDIR.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Many USB host controller drivers contain almost identical copies of the
same virtual root hub descriptors. Put these into a common file to avoid
duplication.
Note that there were some very minor differences between the descriptors
in the various files, such as:
- USB 1.0 vs. USB 1.1
- Manufacturer/Device ID
- Max packet size
- String content
I assume these aren't relevant.
Cc: Thomas Lange <thomas@corelatus.se>
Cc: Shinya Kuribayashi <skuribay@pobox.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Eric Millbrandt <emillbrandt@coldhaus.com>
Cc: Pierre Aubert <p.aubert@staubli.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Zhang Wei <wei.zhang@freescale.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Markus Klotzbuecher <mk@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: C Nauman <cnauman@diagraph.com>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Thomas Abraham <t-abraham@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Cc: Matej Frančeškin <matej.franceskin@comtrade.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
T1040 SoC has SCFG (Supplement Configuration) Block which provides
chip specific configuration and status support. The base address of
SCFG block in T1040 is 0xfc000.
SCFG contains SCFG_PIXCLKCR (DIU pixel clock control register)
at offset 0x28.
Add definition of
-SCFG block
-SCFG_PIXCLKCR register
-Bits definition of SCFG_PIXCLK register
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This implements stashing of bootstage timing data to FDT and automatic
timing reporting. To enable define CONFIG_BOOTSTAGE_FDT and
CONFIG_BOOTSTAGE_REPORT respectively.
Signed-off-by: Rommel G Custodio <sessyargc+u-boot@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
USB spec says that the minimum disconnect threshold should be
over 525 mV. However, internal USB PHY threshold value is below
this specified value. Due to this some devices disconnect at
run-time. Hence, phy settings are tweaked to increased disconnect
threshold to be above 525mV by using this workaround.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384)
and at cold temperatures(A006475), workaround recalibrate the
PLLs with some SerDes configuration
Both these errata are only applicable for b4 rev1.
So, make workaround for these errata conditional,
depending upon soc version.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4860 has two PLL per SerDes whereas B4420 has one PLL per SerDes,
add their defines in arch/powerpc/include/asm/config_mpc85xx.h
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On B4860 and B4420, some serdes protocols can be used with LC VCO as
well as Ring VCO options.
Addded Alternate options with LC VCO for such protocols.
For example protocol 0x2a on srds 1 becomes 0x29 if it is LC VCO.
The alternate option has the same functionality as the original option;
the only difference being LC VCO rather than Ring VCO.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1) SerDes2 Refclks have been set properly to make
PCIe SATA to work as it work on SerDes refclk of 100MHz
2) Mask the SerDes's device reset request before changing
the Refclks for SerDes1 and SerDes2 for PLL locks to
happen properly, device reset request bit unmasked
after SerDes refclks configuration
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1) Add new SerDes1 protocols having Aurora in them
2) Add VSC cross point connections for Aurora to work with
CPRI and SGMIIs
3) Configure VSC crossbar switch to connect SerDes1
lanes to aurora on board, by checking SerDes1 protocols
4) SerDes1 Refclks have been set properly to make
Aurora, CPRI and SGMIIs to work together properly
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
"checkgcc4" is used only for PowerPC.
Move it to arch/powerpc/config.mk.
To make sure gcc is new enough before beginning build,
run "checkgcc4" during "archprepare".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.
All boards with mpc8260 cpu defined both of them:
- CONFIG_MPC8260 was defined in board config headers
and include/common.h
- CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk
We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.
This commit does:
- Delete CONFIG_8260 and CONFIG_MPC8260 definition
in config headers and include/common.h
- Rename CONFIG_8260 to CONFIG_MPC8260
in arch/powerpc/cpu/mpc8260/config.mk.
- Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Before this commit, USE_PRIVATE_LIBGCC was defined in
arch-specific config.mk and referenced in
arch/$(ARCH)/lib/Makefile.
We are not happy about parsing config.mk again and again.
We have to keep the same behavior with a different way.
By adding "CONFIG_" prefix, this macro appears
in include/autoconf.mk, include/spl-autoconf.mk.
(And treating USE_PRIVATE_LIBGCC as CONFIG macro
is reasonable enough.)
Tegra SoC family defined USE_PRIVATE_LIBGCC as "yes"
in arch/arm/cpu/arm720t/tegra*/config.mk,
whereas did not define it in arch/arm/cpu/armv7/tegra*/config.mk.
It means Tegra enables PRIVATE_LIBGCC only for SPL.
We can describe the same behavior by adding
#ifdef CONFIG_SPL_BUILD
# define CONFIG_USE_PRIVATE_LIBGCC
#endif
to include/configs/tegra-common.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
As ppc4xx currently only supports the deprecated nand_spl infrastructure
and nobody seems to have time / resources to port this over to the newer
SPL infrastructure, lets remove NAND booting completely.
This should not affect the "normal", non NAND-booting ppc4xx platforms
that are currently supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Tested-by: Matthias Fuchs <matthias.fuchs@esd.eu>
The syntax
CROSS_COMIPLE ?= <cross_compiler_prefix>
does not work because config.mk is parsed after
exporting CROSS_COMPILE.
Like Linux Kernel's arch/$(ARCH)/Makefile,
we must write as follows:
ifeq ($(CROSS_COMPILE),)
CROSS_COMPILE := <cross_compiler_prefix>
endif
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
- fix serdes definition for t2081.
- fix clock speed for t2081.
- update ids, as CONFIG_FSL_SATA_V2 is needed only for t2080,
T2081 has no SATA.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This function has been around for powerpc. It is used for systems with
memory more than CONFIG_MAX_MEM_MAPPED. In case of non-contiguous memory,
this feature can limit U-boot to one block without going over the limit.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Now we are ready to switch over to real Kbuild.
This commit disables temporary scripts:
scripts/{Makefile.build.tmp, Makefile.host.tmp}
and enables real Kbuild scripts:
scripts/{Makefile.build,Makefile.host,Makefile.lib}.
This switch is triggered by the line in scripts/Kbuild.include
-build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build.tmp obj
+build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build obj
We need to adjust some build scripts for U-Boot.
But smaller amount of modification is preferable.
Additionally, we need to fix compiler flags which are
locally added or removed.
In Kbuild, it is not allowed to change CFLAGS locally.
Instead, ccflags-y, asflags-y, cppflags-y,
CFLAGS_$(basetarget).o, CFLAGS_REMOVE_$(basetarget).o
are prepared for that purpose.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
This commit changes the working directory
where the build process occurs.
Before this commit, build process occurred under the source
tree for both in-tree and out-of-tree build.
That's why we needed to add $(obj) prefix to all generated
files in makefiles like follows:
$(obj)u-boot.bin: $(obj)u-boot
Here, $(obj) is empty for in-tree build, whereas it points
to the output directory for out-of-tree build.
And our old build system changes the current working directory
with "make -C <sub-dir>" syntax when descending into the
sub-directories.
On the other hand, Kbuild uses a different idea
to handle out-of-tree build and directory descending.
The build process of Kbuild always occurs under the output tree.
When "O=dir/to/store/output/files" is given, the build system
changes the current working directory to that directory and
restarts the make.
Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>"
syntax for descending into sub-directories.
(We can write it like "make $(obj)=<sub-dir>" with a shorthand.)
This means the current working directory is always the top
of the output directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
IFC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of IFC IP.
So update acessor functions with common IFC acessor functions to take care
both type of endianness.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Define CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE macro for enabling dual
phy in t1040
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040 has only one SerDes block. so update the code accordingly.
Also, add support of SerDes Protocol 0x00, 0x06, 0x40, 0x69 0x85,
0xA7 and 0xAA
Signed-off-by: Arpit Goel <B44344@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Removed LIODNs for RMAN, RIO, 10G. T1040 has 10 QMAN portals so assigned
LIODNs accordingly.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We do not have to define CONFIG_MPC5xxx in board config headers
(and start.S) because it is defined in arch/powerpc/cpu/mpc5xxx/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Define CONFIG_MPC86xx in arch/powerpc/cpu/mpc86xx/config.mk
because all target boards with mpc86xx cpu define it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk
because all target boards with mpc85xx cpu define it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
We do not have to define CONFIG_5xx in a source file
because it is defined in arch/powerpc/cpu/mpc5xx/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
We do not have to define CONFIG_8xx in source files
because it is defined in arch/powerpc/cpu/mpc8xx/config.mk
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Commit 643aae1406
deleted include/linux/config.h but missed to
delete _LINUX_CONFIG_H macro.
It is no longer used at all.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
On BSC9131, BSC9132, P1010 : For High Capacity SD Cards (> 2 GBytes), the
32-bit source address specifies the memory address in block address
format. Block length is fixed to 512 bytes as per the SD High Capacity
specification. So we need to convert the block address format
to byte address format to calculate the envaddr.
If there is no enough space for environment variables or envaddr
is larger than 4GiB, we relocate the envaddr to 0x400. The address
relocated is in the front of the first partition that is assigned
for sdboot only.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Using the TPL method for nand boot by sram was already
supported. Here add some code for mpc85xx ifc nand boot.
- For ifc, elbc, esdhc, espi, all need the SPL without
section .resetvec.
- Use a clear function name for nand spl boot.
- Add CONFIG_SPL_DRIVERS_MISC_SUPPORT to compile the fsl_ifc.c
in spl/Makefile;
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable Erratum A006379 for T2080, T2081, T4160, B4420.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_SYS_FSL_NUM_USB_CTRLS is no longer used,
update it to new CONFIG_USB_MAX_CONTROLLER_COUNT.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Single-source clocking is new feature introduced in T1040.
In this mode, a single differential clock is supplied to the
DIFF_SYSCLK_P/N inputs to the processor, which in turn is
used to supply clocks to the sysclock, ddrclock and usbclock.
So, both ddrclock and syclock are driven by same differential
sysclock in single-source clocking mode whereas in normal clocking
mode, generally separate DDRCLK and SYSCLK pins provides
reference clock for sysclock and ddrclock
DDR_REFCLK_SEL rcw bit is used to determine DDR clock source
-If DDR_REFCLK_SEL rcw bit is 0, then DDR PLLs are driven in
normal clocking mode by DDR_Reference clock
-If DDR_REFCLK_SEL rcw bit is 1, then DDR PLLs are driven in
single source clocking mode by DIFF_SYSCLK
Add code to determine ddrclock based on DDR_REFCLK_SEL rcw bit.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Convert like follows:
CPU mpc83xx -> CONFIG_MPC83xx
CPU mpc85xx -> CONFIG_MPC85xx
CPU mpc86xx -> CONFIG_MPC86xx
CPU mpc5xxx -> CONFIG_MPC5xxx
CPU mpc8xx -> CONFIG_8xx
CPU mpc8260 -> CONFIG_8260
CPU ppc4xx -> CONFIG_4xx
CPU x86 -> CONFIG_X86
ARCH x86 -> CONFIG_X86
ARCH powerpc -> CONFIG_PPC
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The next version VxWorks adopts device tree (for PowerPC and ARM) as its hardware
description mechanism. For PowerPC, the boot interface conforms to
the ePAPR standard, which is:
void (*kernel_entry)(ulong fdt_addr,
ulong r4 /* 0 */,
ulong r5 /* 0 */,
ulong r6 /* EPAPR_MAGIC */, ulong r7 /* IMA size */,
ulong r8 /* 0 */, ulong r9 /* 0 */)
For ARM, the boot interface is:
void (*kernel_entry)(void *fdt_addr)
Signed-off-by: Miao Yan <miao.yan@windriver.com>
[trini: Fix build error when !CONFIG_OF_FDT is set, typo on PowerPC,
missing extern ft_fixup_num_cores]
Signed-off-by: Tom Rini <trini@ti.com>
PLATFORM_RELFLAGS += -meabi
PLATFORM_CPPFLAGS += -ffixed-r2
were defined in all arch/powerpc/${CPU}/config.mk.
This commit moves them to arch/powerpc/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The default value of CONFIG_SYS_FSL_TBCLK_DIV is 16.
So, update its value as default.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
A new valid setting case added for fman1, it uses platform frequency.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
MPC8349 has been using mpc85xx DDR driver through a symbolic link to
mpc85xx_ddr_gen2.c. After consolidating the drivers to a single set
under driver/ddr/fsl/, the link is replaced by referring driver
directly. We now can simply enable the macro and use the driver.
Other mpc83xx SoCs still use their own driver.
Signed-off-by: York Sun <yorksun@freescale.com>
MEM_PLL_RAT on T4240/T4160 Rev2.0 uses a value which is half of Rev1.0.
It's 12 in Rev1.0, for Rev2.0 it uses 6.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
In PBL RAMBOOT(SPI/SD/NAND boot) mode, CPC1 used as SRAM, should disable
CPC1 speculation and keep it till relocation. Otherwise, speculation
transactions will go to DDR controller, it will cause problem.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Add support for Freescale T2080/T2081 SoC.
T2080 includes the following functions and features:
- Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 mEMACs for network interfaces (four 1Gbps MACs and four 10Gbps/1Gbps MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T2080 and T2081:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
There are more than two 10GEC in single FMAN in some SoCs(e.g. T2080).
This patch adds support for 10GEC3 and 10GEC4.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/misc
and fix the header file includes.
Signed-off-by: York Sun <yorksun@freescale.com>
Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
The offset of register address within GPIO module is just
CONFIG_SYS_MPC85xx_GPIO_ADDR. So, fix it. The following platforms
are confirmed: MPC8572, P1023, P1020, P1022, P2020, P4080,
P5020, P5040, T4240, B4860.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
When indexing freqProcessor[] we use the first
value in the cpu's "reg" property, which on
new e6500 cores IDs the threads.
But freqProcessor[] should be indexed with a
core index so, when fixing "the clock-frequency"
cpu node property, access the freqProcessor[]
with the core index derived from the "reg' property.
If we don't do this, last half of the "cpu" nodes
will have broken "clock-frequency" values.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Update the code that builds the pci endpoint liodn
offset list so that it doesn't overlap with other
liodns and doesn't generate negative offsets like:
fsl,liodn-offset-list = <0 0xffffffcd 0xffffffcf
0xffffffd1 0xffffffd3
0xffffffd5 0xffffffd7
0xffffffd9 0xffffffdb>;
The update consists in adding a parameter to the
function that builds the list to specify the base
liodn.
On PCI v2.4 use the old base = 256 and, on PCI 3.0
where some of the PCIE liodns are larger than 256,
use a base = 1024. The version check is based on
the PCI controller's version register.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: York Sun <yorksun@freescale.com>
The liodn for the T4240's PCIE controller is no longer set
through a register in the guts register block but with one
in the PCIE register block itself.
Use the already existing SET_PCI_LIODN_BASE macro that puts
the liodn in the correct register.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: York Sun <yorksun@freescale.com>
T1040 Soc has four personalities:
-T1040 (4 cores with L2 switch)
-T1042:Reduced personality of T1040 without L2 switch
-T1020:Reduced personality of T1040 with less cores(2 cores)
-T1022:Reduced personality of T1040 with 2 cores and without L2 switch
Update defines in arch/powerpc header files, Makefiles and in
driver/net/fm/Makefile to support all T1040 personalities
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: fixed Makefiles]
Acked-by: York Sun <yorksun@freescale.com>
The MPC824x processors have long reached EOL, and the PN62 board has
not seen any board-specific updates for more than a decade. It is now
causing build issues. Instead of wasting time on things nobody is
interested in any more, we rather drop this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
cc: Tom Rini <trini@ti.com>
Linux Kernel abolished include/linux/config.h long time ago.
(around version v2.6.18..v2.6.19)
We don't need to provide Linux copatibility any more.
This commit deletes include/linux/config.h
and fixes source files not to include this.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Note:
arch/powerpc/cpu/mpc8260/Makefile is originally like follows:
---<snip>---
START = start.o kgdb.o
COBJS = traps.o serial_smc.o serial_scc.o cpu.o cpu_init.o speed.o \
---<snip>---
COBJS-$(CONFIG_ETHER_ON_SCC) = ether_scc.o
---<snip>---
$(LIB): $(OBJS)
$(call cmd_link_o_target, $(OBJS) $(obj)kgdb.o)
The link rule `$(call cmd_link_o_target, $(OBJS) $(obj)kgdb.o)'
is weird.
kbdg.o is not included in $(OBJS) but linked into $(LIB)
and $(LIB) is not dependent on kgdb.o.
(Broken dependency tracking)
So,
START = start.o kgdb.o
shoud have been
START = start.o
SOBJS = kgdb.o
That is why this commit adds kgdb.o to obj-y, not to extra-y.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
This allows to share some common code for the boards that use a corenet
base SoC.
Two different versions of the function are available in
fsl_corenet_serdes.c and fsl_corenet2_serdes.c files.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix t1040qds.c]
Acked-by: York Sun <yorksun@freescale.com>
If the DDR3 module supports industrial temperature range and requires
the x2 refresh rate for that temp range, the refresh period must be
3.9us instead of 7.8 us.
This was successfuly tested on kmp204x board with some MT41K128M16 DDR3
RAM chips (no module used, chips directly soldered on board with an SPD
EEPROM).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix minor conflicts in fsl_ddr_dimm_params.h,
lc_common_dimm_params.c, common_timing_params.h]
Acked-by: York Sun <yorksun@freescale.com>
When exporting the new memsize without reserved PRAM area, the -Wformat
option produces a warning since %ld is used for snprintf and bi_memsize
is phys_size_t.
This patch removes this warning for all PRAM PowerPC boards.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Introduce different macros for storing addresses of multiple
USB controllers. This is required for successful initialization
and usage of multiple USB controllers inside u-boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
CONFIG_USB_MAX_CONTROLLER_COUNT macro recently defined for
initializing all USB controllers on a given platform. This
macro is defined for all 85xx socs
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Previously, the address of a requested capability is define like that
"#define PCI_DCR 0x78"
But, the addresses of capabilities is different with regard to PCIe revs.
So this method is not flexible.
Now a function to get the address of a requested capability is added and used.
It can get the address dynamically by capability ID.
The step of this function:
1. Read Status register in PCIe configuration space to confirm that
Capabilities List is valid.
2. Find the address of Capabilities Pointer Register.
3. Find the address of requested capability from the first capability.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Erratum A006379 says CPCHDBCR0 bit field [10:14] has incorrect default
value after POR. The workaround is to set this field before enabling
CPC to 0x1e.
Erratum A006379 applies to
T4240 rev 1.0
B4860 rev 1.0, 2.0
Signed-off-by: York Sun <yorksun@freescale.com>
Some DDR related structures present in fsl_ddr_dimm_params.h, fsl_ddr_sdram.h, ddr_spd.h
has various parameters with embedded acronyms capitalized that trigger the CamelCase
warning in checkpatch.pl
Convert those variable names to smallcase naming convention and modify all files
which are using these structures with modified structures.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
CHASSIS2 architecture never fix clock groups for Cluster and hardware
accelerator like PME, FMA. These are SoC defined. SoC defines :-
- NUM of PLLs present in the system
- Clusters and their Clock group
- hardware accelerator and their clock group
if no clock group, then platform clock divider for FMAN, PME
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
T1040 SoC has
- DDR controller ver 5.0
- 2 PLLs
- 8 IFC Chip select
- FMAN Muram 192K
- No Srio
- Sec controller ver 5.0
- Max CPU update for its personalities
So, update the defines accordingly.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CHASSIS2 architecture never defines type of L2 cache present in SoC.
it is dependent upon the core present in the SoC.
for example,
- e6500 core has L2 cluster (Kibo)
- e5500 core has Backside L2 Cache
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
This patch is for board config file not to add CONFIG_SECURE_BOOT
condition for include the asm/fsl_secure_boot.h.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license. However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word. I'd prefer
to be consistent to this end".
Change the license IDs to use the official name.
Signed-off-by: Wolfgang Denk <wd@denx.de>
In a very rare condition, a system hang is possible when the e500 core
initiates a guarded load to PCI / PCIe /SRIO performs a coherent write
to memory. Please refer to errata document for more details. This erratum
applies to the following SoCs and their variants, if any.
BSC9132
BSC9131
MPC8536
MPC8544
MPC8548
MPC8569
MPC8572
P1010
P1020
P1021
P1022
P1023
P2020
C29x
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
The source clock frequency of I2C bus on p1022 is the platform(CCB)
clock, not CCB/2. The wrong source clock frequency leads to wrong
I2C bus speed setting. so, fixed it.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
- Added section "u_boot_list" in arch/powerpc/cpu/mpc85xx/u-boot-spl.lds
- Use the function i2c_init_all instead of i2c_init
Signed-off-by: Ying Zhang <b40530@freescale.com>
Multiple read/write transactions initiated by security
engine may cause system to hang.
Workaround: set MCFGR[AXIPIPE] to 0 to avoid hang.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Makes the startup output more consistent
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Makes the startup output more consistent
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions.
because of this code checkpatch script generates "WARNING: Avoid CamelCase".
Convert variables name to normal naming convention and modify board, driver
files with updated the new structure.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it.
2. Some functions were unused in the minimal SPL, but it is useful
in the common SPL. So, enabled some functionality for common SPL.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.
At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.
The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
Remove getting values of usb mode and phy_type from "usb_dr_mode"
and "usb_phy_type" uboot env variables. Now, these are determined
only from hwconfig string
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
fsl_usb.h file created to share data bewteen usb platform code
and usb ip driver. Internal phy structure definitions moved to
this file
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
It is not necessary for all processor to have serdes block 1 & 2.
They may have only one serdes block.
So, put serdes block 1 & 2 related code under defines
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Fix the license header introduced by the following patches
Add TWR-P10xx board support
Add T4240EMU target
IDT8T49N222A configuration code
Add C29x SoC support
Add support for C29XPCIE board
Signed-off-by: York Sun <yorksun@freescale.com>
This patch moves all the font configuration values into video_font_data.h
so they are all in the right place with the font. The video_font.h now only
includes video_font_data.h and will allow us to select and include different
font once more fonts are added.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[agust: fixed build warning for mcc200]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix the following build error caused by patch "powerpc/pcie: add PCIe
version 3.x support":
pcie.c:302:34: error: 'PCI_LTSSM' undeclared (first use in this function)
pcie.c:303:15: error: 'PCI_LTSSM_L0' undeclared (first use in this function)
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The TIMING_CFG_3[EXT_ACTTOPRE] register field is 2 bits wide, but
the mask omitted the LSB. This patch provides a 2-bit wide mask.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The Freescale C29x family is a high performance crypto co-processor.
It combines a single e500v2 core with necessary SEC engine. There're
three SoC types(C291, C292, C293) with the following features:
- 512K L2 Cache/SRAM and 512 KB platform SRAM
- DDR3/DDR3L 32bit DDR controller
- One PCI express (x1, x2, x4) Gen 2.0 Controller
- Trust Architecture 2.0
- SEC6.0 engine
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Po Liu <Po.Liu@freescale.com>
T4240 PCIe IP is version 3.0 and has some update comparing previous
QorIQ products.
1. Move Freescale specific register define
to
arch/powerpc/include/asm/fsl_pci.h
and update the register offset define for T4240.
2. add the status/control register define
use status/control register to judge the link status
3. The original code uses 'Programming Interface' field to judge if PCIE is
EP or RC mode, however, T4240 does not support this functionality.
According to PCIE specification, 'Header Type' offset 0x0e is used to
indicate header type, so for PCIE controller, the patch changes code to
use 'Header Type' field to identify if the PCIE is RC or EP mode.
This patch fixes the PCIe card link up issue on T4240QDS.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
1. Add CONFIG_SYS_DPAA_RMAN macro to t4240 and b4860.
2. Decrease RMan liodn offset number.
SET_RMAN_LIODN() is used to set liodn offset of RMan blocks 0-3.
For t4240 and b4860, RMan liodn base is assigned to 922, the original
offset number is too large that the liodn (base+offset 922+678 = 1600)
is greater than 0x500 the maximum liodn number.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Also change the define name SRDS_RSTCTL_SDPD to
SRDS_RSTCTL_SDEN, which stands for SerDes enable
as mentioned in SerDes module guide
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
BSC9132 SoC has two separate DDR controllers for PowerPC side and DSP side
DDR. They are mapped to PowerPC and DSP CCSR space respectively.
BSC9132QDS has two on-board MC34716EP DDR3 memory one connected to PowerPC
and other to DSP side controller.
Configure DSP DDR controller similar to PowerPC side DDR controller as
memories are exactly similar.
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a
integrated device that contains two powerpc e500v2 cores and two DSP
starcores.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 and M3 memory
-Creating LAW for 1GB DDR which is connected exclusively to DSP-cores
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
When a board (slave) boots from SRIO/PCIE, it would get the instructions
from a remote board (master) by SRIO/PCIE interface, and the slave's
u-boot image should be built with the
SYS_TEXT_BASE=0xFFF80000;
So the u-boot of the slave should avoid the NOR_BOOT branch at the
booting stage.
For example, when a P2041RDB boots from SRIO/PCIE, it will set TLB
entry 15 from base address "CONFIG_SYS_MONITOR_BASE & 0xffc00000",
and with the 4M size as the boot window in NOR_BOOT branch. Because
the CONFIG_SYS_MONITOR_BASE = CONFIG_SYS_TEXT_BASE = 0xFFF80000, so
the TLB entry will be from base address 0xffc00000 and with 4M size.
Then the u-boot will set TLB entry 14 from base address
"CONFIG_SYS_INIT_RAM_ADDR", and with the 16K size as the initial
stack window. For the P2041RDB platform, the CONFIG_SYS_INIT_RAM_ADDR
= 0xffd00000. So the TLB entry 14 and 15 will be in confliction.
There will be right TLB entries configurations when avoid the
NOR_BOOT branch and set the boot window from 0xfff00000 with 1M
size space.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Erratum A-005812 Incorrect reservation clearing in Write Shadow mode can
result in invalid atomic operations. For u-boot, this erratum only impacts
SoCs running in write shadow mode.
Signed-off-by: York Sun <yorksun@freescale.com>
JEDEC spec requires the clocks to be stable before deasserting reset
signal for RDIMMs. Clocks start when any chip select is enabled and
clock control register is set. This patch also adds the interface to
toggle memory reset signal if needed by the boards.
Signed-off-by: York Sun <yorksun@freescale.com>
On selected platforms, x4 DDR devices can be supported. Using x4 devices may
lower the performance, but generally they are available for higher density.
Tested on MT36JSF2G72PZ-1G9E1 RDIMM.
Signed-off-by: York Sun <yorksun@freescale.com>
When chip select interleaving is enabled, cs0_bnds is used for address
binding. Other csn_bnds are not used. When two controllers interleaving is
enabled, cs0_bnds of both controllers are used, other csn_bnds are not.
However, the unused csn_bnds may be used internally for calculating
addresses for calibration. Setting those registers to 0 may confuse
controllers in some cases. Instead, setting them to 0xffffffff together
with normal LAWs will guarantee the address is not mapped to DDR.
Signed-off-by: York Sun <yorksun@freescale.com>
Prepare for emulator support for mpc85xx parts.
Disable DDR training and skip wrlvl_cntl_2 and wrlvl_cntl_3 registers.
These two registers improve stability but not supported by emulator.
Add CONFIG_FSL_TBCLK_EXTRA_DIV for possible adjustment to time base.
Signed-off-by: York Sun <yorksun@freescale.com>
Move CONFIG_FSL_CORENET define to config_mpc85xx.h. It is not board
specific feature and belongs to SoC header.
Signed-off-by: York Sun <yorksun@freescale.com>
For some PowerPC platforms, LIODN registers for SRIO ports are
in SRIO register address space. So the ccsr_rio structure should
be updated for those LIODN registers.
In addition, add a new macro "SET_SRIO_LIODN_BASE" to create
the SRIO LIODN ID table based on the SRIO LIODN register address.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
CONFIG_I2C_MUX is replaced through the new i2c multibus/multiadapter
framework, configured through CONFIG_SYS_I2C. As CONFIG_I2C_MUX
is only used on the keymile boards, and they are now completely
moved to the new framework, remove CONFIG_I2C_MUX.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-By: Holger Brunck <holger.brunck@keymile.com>
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
CONFIG_SPL_BUILD creates debug TLB entry, so disable it before init_tlbs.
CONFIG_SPL_INIT_MINIMAL never creates any debug TLB entry, so no need
of disable_tlb().
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
MAKEALL is fine for ppc4xx and mpc85xx.
Run checks were done on our controlcenterd hardware.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Patch 35fc84fa1 [Refactor the bootm command to reduce code duplication]
breaks booting Linux (compressed uImage with fdt) on powerpc.
boot_jump_linux() mustn't be called before boot_prep_linux() and
boot_body_linux() have been called. So remove the superfluous call
to boot_jump_linux() in arch/powerpc/lib/bootm.c as its called later on
in this function.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
init_tlbs() initialize all the TLB entries required for the system.
So disable DEBUG TLB entry before TLB entries initialization.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If a variable is used as array subscript, it's valid value range is
0 ... ARRAY_SIZE -1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There will clear the BSS in the function clear_bss(), the reset address of
the BSS started from the __bss_start, and increased by four-byte increments,
finally stoped depending on the address is equal to the _bss_end. If the end
address __bss_end is not alignment to 4byte, it will be an infinite loop.
1. The reset action stoped depending on the reset address is greater
than or equal the end address of the BSS.
2. The end address of the BSS should be 4byte aligned. Because the reset unit
is 4 Bytes.
This patch is on top of the patch "powerpc/mpc85xx: support application
without resetvec segment in the linker script".
Signed-off-by: Ying Zhang <b40530@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For SD/SPI 2-stage bootloader, the On-Chip Rom code loads the SPL into L2 SRAM,
then jump to it to begin execution. After that, the SPL loads the final uboot
image into DDR, then jump to it to begin execution. The segment .resetvec in
the SPL and in final U-boot is useless.
So, add new symbols CONFIG_SYS_MPC85XX_NO_RESETVEC for this application.
If CONFIG_SYS_MPC85XX_NO_RESETVEC is set, the segment .resetvec is excluded
and the segment .bootpg is placed in the previous 4K of the segment .text.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum A-006593 is "Atomic store may report failure but still allow
the store data to be visible".
The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit
21 to 1'b1. This may have a small impact on synthetic write bandwidth
benchmarks but should have a negligible impact on real code."
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Calculate reserved fields according to IFC bank count
1. Move csor_ext register behind csor register and fix res offset
2. Move ifc bank count to config_mpc85xx.h to support 8 bank count
3. Guard fsl_ifc.h with CONFIG_FSL_IFC macro to eliminate the compile
error on some devices that does not have IFC controller.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a T4 board boots from SRIO or PCIE, it needs to finish these processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable
the master module of Boot from SRIO and PCIE on a platform. But this
is not a silicon feature, it's just a specific booting mode based on
the SRIO and PCIE interfaces. So it's inappropriate to put the macro
into the file arch/powerpc/include/asm/config_mpc85xx.h.
Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to
"CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from
arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros
in configuration header file of each board which can support the
master module of Boot from SRIO and PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Freescale documentation presents the PowerPC core names in lower case, such as
"e300", "e500", "e600", etc.
Change the upper case occurrences into lower case so that the core names
reported in U-boot can match the ones from the documentation.
While at it also fix a checkpatch error:
ERROR: space prohibited before that close parenthesis ')'
#53: FILE: arch/powerpc/cpu/mpc86xx/cpu.c:81:
+ printf("e600 Core %d", (msscr0 & 0x20) ? 1 : 0 );
Reported-by: Heinz Wrobel <heinz.wrobel@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB is a Freescale Reference Design Board for
BSC9131 SoC which is a integrated device that contains
one powerpc e500v2 core and one DSP starcore.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 memory
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Linker script is not able find start.o binary. So add its absolute path in
u-boot-spl.lds. This change is similar to u-boot-nand.lds
common/Makefile: Avoid compiling unnecssary files
fsl_ifc_spl.c : It is is responsible for reading u-boot binary from
NAND flash and copying into DDR. It also transfer control from NAND SPL
to u-boot image present in DDR.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
IFC errata A003399 is valid for IFC NOR boot i.e.if no on-board NOR flash or
no NOR boot, do not compile its workaround.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
To avoid sign extension problem, use explicit casting to cast
the SDRAM size to type phys_size_t, or else, if the SDRAM size
is 2G(0x80000000), it will be extended to 0xffffffff80000000
when phys_size_t is type 'unsigned long long'.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Accidentally applied an earlier version of the patch, which set
the compatible to "fsl,qoriq-clockgen-2", lacking the final
".0".
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
C99's strict aliasing rules are insane to use in low-level code such as a
bootloader, but as Wolfgang has rejected -fno-strict-aliasing in the
past, add a union so that 16-bit accesses can be performed.
Compile-tested only.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
dcbi instruction has been used to clear D-cache lock. However, the cache
lock is persistent for e6500 core. Use dcblc to clear the lock explicitly.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Boot ROM code creates TLB entries for 3.5G space before entering
the u-boot. Earlier we were deleting these entries after early
initialization of CPU. In recent past, code has been added
to invalidate all these entries before relocation of u-boot code.
So this code to delete TLB entries after CPU initialization
is no longer required.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Acked-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4420 is a subset of B4860. Merge them in config_mpc85xx.h to simplify
the defines.
- Removed #define CONFIG_SYS_FSL_NUM_CLUSTERS as this is used nowhere.
- defined CONFIG_SYS_NUM_FM1_10GEC to 0 for B4420 as it does not have 10G.
Also move CONFIG_E6500 out of B4860QDSds.h into config_mpc85xx.h.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Allow DDR clock runs faster than SPD specifes. This may cause memory
failure, but the user should know what is going to happen when using
higher than expected DDR clock.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
To align with chassis generation 2 spec, all cores are numbered in sequence.
The cores may reside across multiple clusters. Each cluster has zero to four
cores. The first available core is numbered as core 0. The second available
core is numbered as core 1 and so on.
Core clocks are generated by each clusters. To identify the cluster of each
core, topology registers are examined.
Cluster clock registers are reorganized to be easily indexed.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T1040 and variants have e5500 cores and are compliant to QorIQ Chassis
Generation 2. The major difference between T1040 and its variants is the
number of cores and the number of L2 switch ports.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4160 is a subset of T4240. Merge them in config_mpc85xx.h to simplify
the defines. Also move CONFIG_E6500 out of t4qds.h into config_mpc85xx.h.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
"cpu <num> status" should check if core is disabled before printing
the spin table location.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The Freescale MPC8220 Power Architecture processors have long reached
EOL; Freescale does not even list these any more on their web site.
Remove the code to avoid wasting maitaining efforts on dead stuff.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
This gives boards flexibility to assign other than default addresses to each
DDR controller. For example, DDR controler 2 can have 0 as the base and DDR
controller 1 has higher memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The workaround has been updated to use a slightly different magic number.
Change from 0x00003000 to 0x30003000.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This is what we have done for the UTMI PHY on P3041/P5020. Then the PHY
initialization can be reused in kernel without “usb start” command.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Removed unused declare serdes_get_prtcl() which was no longer needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1, Implemented board_ft_fman_fixup_port() to fix port for kernel.
2, Implemented fdt_fixup_board_enet() to fix node status of different
slots and interfaces.
3, Adding detection of slot present for XGMII interface.
4, There is no PHY for XFI, so removed related phy address settings.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When CONFIG_SYS_FSL_QORIQ_CHASSIS2 is not defined, QMAN frequency will not
be initialized, and QMAN will have a wrong frequency display.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4160 SoC is low power version of T4240. The T4160 combines eight dual
threaded Power Architecture e6500 cores and two memory complexes (CoreNet
platform cache and DDR3 memory controller) with the same high-performance
datapath acceleration, networking, and peripheral bus interfaces.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Protocols are constants. Fix arrays with const prefix.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The PIR parsing algorithm we used is not only for E6500. It applies to all
SoCs with chassis 2.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Use decimal and hexadecimal for protocol numbers. It helps to match with
SoC user manual.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4240 internal UTMI phy is different comparing to previous UTMI PHY
in P3041.
This patch adds USB 2.0 UTMI Dual PHY new memory map and enable it for
T4240.
The phy timing is very sensitive and moving the phy enable code to
cpu_init.c will not work.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Missing nodes of crypto, pme, etc in device tree is not a fatal error.
Setting up the qman portal should skip the missing node and continue
to finish the rest.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Should check if interleaving is enabled before using interleaving mode.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Lane H on SerDes4 should be SATA2 instead of SATA1
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The L1 D-cache on e6500 is write-through. This means that it's not
considered a good idea to have the L1 up and running if the L2 is
disabled. We don't actually *use* the L1 until after the L2 is
brought up on e6500, so go ahead and move the L1 enablement after
that code is done.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix ccsr_gur for corenet platform. Remove non-exist registers. Add fuse
status register.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Makes it a bit easier to see if we've properly set them. While
we're in there, modify the accesses to HDBCR0 and HDBCR1 to actually
use those definitions.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The bit positions for FMAN1 freq in RCW is different for B4860.
Also addded a case when FMAN1 frewuency is equal to systembus.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Rather than having similar code in powerpc, use image_setup_linux() which
should be common across all architectures that use the FDT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Extending LIODN offset range from 1-5 to 1-10
While using a qman portal with a higher index the LIODN offset
is incorrectly set, thus extending the range of offsets covers
all 10 qman portals
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Acked-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum DDR_A003 applies to P5020, P3041, P4080, P3060, P2041, P5040.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Only some chips have four SerDes banks, so don't define lanes for a bank
that doesn't exist.
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
As per Errata list of BSC9131 and BSC9132, IFC Errata A003399 is no more
valid. So donot compile its workaround.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal
multi-bit ECC errors, which has impact on performance, so software should
disable all ECC reporting from USB1 and USB2.
In formal release document, the errata number should be USB14 instead of USB138.
Signed-off-by: xulei <Lei.Xu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: xulei <B33228@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some legacy RGMII phys don't have in band signaling for the
speed information. so set the RGMII MAC mode according to
the speed got from PHY.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reported-by: John Traill <john.traill@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For T4/B4, the clockgen node compatible string is updated to version 2.
Add clock-frequency setting for this new version.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Per the latest errata updated, B4860/B4420 Rev 1.0 has also
errata A-005871, so adding define A-005871 for B4 SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4420/B4860 PCIE can not work because of the wrong definition of
the PCIE register offset in the file:
arch/powerpc/include/asm/immap_85xx.h
Add the judgement of B4420/B4860 to make the register offset to:
#define CONFIG_SYS_MPC85xx_PCIE1_OFFSET 0x200000
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Set the device tree property associated with the mpic source
frequency. The frequency is used for mpic timer.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The 'fsl,pme-rev1' and 'fsl-pme-rev2' properties have been added to the
pme portal node. This is required for software to determine which version
of PME hardware is present and take appropriate actions.
These properties are a direct reflection of the corresponding ccsr pme
register value.
Also removed unnecessary static global variables.
Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Delete all occurrences of hang() and provide a generic function.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
Make all mpc512x code point to the new common fsl_iim driver, and remove the
former mpc512x-specific iim driver.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This patch adds SPL booting support (NOR flash) for the
PPC4xx platforms.
This SPL booting (Falcon mode) will be used by the upcoming
lcd4_lwmon5 board port (lwmon5 variant).
Signed-off-by: Stefan Roese <sr@denx.de>
If watchdog is enabled, the arch/powerpc/lib/ticks.S::wait_ticks() function
calls the function specified by the WATCHDOG_RESET macro.
The wait_ticks function depends on the registers r0, r6 and r7 being
preserved however that is not guaranteed, e.g. if the reset function is a
C function this will probably overwrite r0 and cause an endless loop.
The following patch changes to using r14+r15 instead of r6+r7 (to resemble
what would have been generated by a C compiler) and saves all necessary
registers on the stack.
The patch has been tested on a custom MPC5125 based machine using the 512x
powerpc architecture.
Signed-off-by: Mats Karrman <mats.karrman@tritech.se>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Tested-by: Stefan Roese <sr@denx.de>
Fix USB device-tree fixup to properly handle device-tree fixup and
print appropriate message when wrong/junk "dr_mode" or "phy_type"
are mentioned in hwconfig string
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
Since the lcd code was compiled unconditionally in arch also
add CONFIG_MPC8XX_LCD to the boards using this driver.
cc: Anatolij Gustschin <agust@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
lcd_color_fg and lcd_color_bg had to be declared in board specific
code, but were not actually used there; in addition, we have getter /
setter functions for these, which were not used either.
Get rid of the global variables, and use the getter function where
needed (so far no setter calls are needed).
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[agust: also fixed cm_t35 board while rebasing]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
These functions are only available for powerpc and are not declared in a
header file. We want to use the rest function in two places (board_f and
board_r), so declare the functions in watchdog.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
We create a separate header file for link symbols defined by the link
scripts. It is helpful to have these all in one place and try to
make them common across architectures. Since Linux already has a similar
file, we bring this in even though many of the symbols there are not
relevant to us.
Each architecture has its own asm/sections.h where symbols specifc to
that architecture can be added. For now everything except AVR32 just
includes the generic header.
One change is needed in arch/avr32/lib/board.c to make this conversion
work.
Reviewed-by: Tom Rini <trini@ti.com> (version 5)
Signed-off-by: Simon Glass <sjg@chromium.org>
Note this is a tree-wide change affecting multiple architectures.
At present we use __bss_start, but mostly __bss_end__. This seems
inconsistent and in a number of places __bss_end is used instead.
Change to use __bss_end for the BSS end symbol throughout U-Boot. This
makes it possible to use the asm-generic/sections.h file on all
archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Refactor linker-generated array code so that symbols
which were previously linker-generated are now compiler-
generated. This causes relocation records of type
R_ARM_ABS32 to become R_ARM_RELATIVE, which makes
code which uses LGA able to run before relocation as
well as after.
Note: this affects more than ARM targets, as linker-
lists span possibly all target architectures, notably
PowerPC.
Conflicts:
arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
board/ait/cam_enc_4xx/u-boot-spl.lds
board/davinci/da8xxevm/u-boot-spl-da850evm.lds
board/davinci/da8xxevm/u-boot-spl-hawk.lds
board/vpac270/u-boot-spl.lds
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
These boards seem to be unmaintained for quite some time. So lets
remove support for them completely. This also cleans up some
common drivers/files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Guillaume Alexandre <guillaume.alexandre@gespac.ch>
Acked-by: Wolfgang Denk <wd@denx.de>
Do maintain a 200 usecs period of stable power and clock before
asserting the CKE signal and sending commands, have at least 200
DRAM clock cycles pass after initialization before data access.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add new mpc5121e based ac14xx board and a new pinmux config
function for setting individual pinmux bit groups. This
function is used in ac14xx board code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Boards may define own IPS divider in the config file if
the default IPS divider doesn't fit their needs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Only define enabled clocks in the config file and enable
the clocks in common code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Wolfgang Denk <wd@denx.de>
Currently each mpc512x board has its own LAW and CS config code,
we should avoid this code duplication. Allow all boards to use
common code by only defining LAW and CS config macros like
CONFIG_SYS_CSx_START, CONFIG_SYS_CSx_SIZE and CONFIG_SYS_CSx_CFG.
Also allow common configuration of additional CS parameters by
CONFIG_SYS_CS_ALETIMING, CONFIG_SYS_CS_BURST, CONFIG_SYS_CS_DEADCYCLE
and CONFIG_SYS_CS_HOLDCYCLE options.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
On MPC5200, the initial RAM (and gd) is located in the internal
SRAM. So we can actually call the preloader console init code
before calling initdram(). This makes serial output (printf)
available very early, even before SDRAM init, which has been
an U-Boot priciple from day 1.
Signed-off-by: Stefan Roese <sr@denx.de>
The libfdt.h file is the definition file for libfdt. It is unnecessary
to include other fdt header files (the necessary ones are pulled in
by libfdt.h).
Signed-off-by: Gerald Van Baren <gvb@unssw.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
trivial:
fdt_support.c:89:64: warning: Using plain integer as NULL pointer
fdt_support.c:325:65: warning: Using plain integer as NULL pointer
fdt_support.c:352:65: warning: Using plain integer as NULL pointer
For the following bad constant expression, We hardcode the max. number of
memory banks to four for the foreseeable future, and add an error with
instructions on what to do once it's exceeded:
fdt_support.c:397:22: error: bad constant expression
For the rest below, sparse found a couple of wrong endian conversions
in of_bus_default_translate() and fdt_get_base_address(), but
otherwise the rest is mostly annotation fixes:
fdt_support.c:64:24: warning: cast to restricted __be32
fdt_support.c:192:21: warning: incorrect type in assignment (different base types)
fdt_support.c:192:21: expected unsigned int [unsigned] [usertype] tmp
fdt_support.c:192:21: got restricted __be32 [usertype] <noident>
fdt_support.c:201:21: warning: incorrect type in assignment (different base types)
fdt_support.c:201:21: expected unsigned int [unsigned] [addressable] [usertype] tmp
fdt_support.c:201:21: got restricted __be32 [usertype] <noident>
fdt_support.c:304:13: warning: incorrect type in assignment (different base types)
fdt_support.c:304:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:304:13: got restricted __be32 [usertype] <noident>
fdt_support.c:333:13: warning: incorrect type in assignment (different base types)
fdt_support.c:333:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:333:13: got restricted __be32 [usertype] <noident>
fdt_support.c:359:13: warning: incorrect type in assignment (different base types)
fdt_support.c:359:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:359:13: got restricted __be32 [usertype] <noident>
fdt_support.c:373:21: warning: cast to restricted __be32
fdt_support.c:963:48: warning: incorrect type in argument 1 (different base types)
fdt_support.c:963:48: expected restricted __be32 const [usertype] *p
fdt_support.c:963:48: got unsigned int [usertype] *<noident>
fdt_support.c:971:48: warning: incorrect type in argument 1 (different base types)
fdt_support.c:971:48: expected restricted __be32 const [usertype] *p
fdt_support.c:971:48: got unsigned int [usertype] *<noident>
fdt_support.c:984:29: warning: incorrect type in argument 1 (different base types)
fdt_support.c:984:29: expected restricted __be32 const [usertype] *cell
fdt_support.c:984:29: got unsigned int [usertype] *addr
fdt_support.c:996:32: warning: incorrect type in argument 1 (different base types)
fdt_support.c:996:32: expected restricted __be32 const [usertype] *cell
fdt_support.c:996:32: got unsigned int [usertype] *addr
fdt_support.c:1041:41: warning: incorrect type in argument 1 (different base types)
fdt_support.c:1041:41: expected restricted __be32 const [usertype] *cell
fdt_support.c:1041:41: got unsigned int [usertype] *addr
fdt_support.c:1053:41: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1053:41: expected restricted __be32 const [usertype] *range
fdt_support.c:1053:41: got unsigned int const [usertype] *[assigned] ranges
fdt_support.c:1064:53: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1064:53: expected restricted __be32 const [usertype] *addr
fdt_support.c:1064:53: got unsigned int [usertype] *addr
fdt_support.c:1110:50: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1110:50: expected restricted __be32 const [usertype] *addr
fdt_support.c:1110:50: got unsigned int *<noident>
fdt_support.c:1121:49: warning: incorrect type in argument 1 (different base types)
fdt_support.c:1121:49: expected restricted __be32 const [usertype] *cell
fdt_support.c:1121:49: got unsigned int *<noident>
fdt_support.c:1147:60: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1147:60: expected restricted __be32 const [usertype] *addr
fdt_support.c:1147:60: got unsigned int *<noident>
fdt_support.c:1081:5: warning: symbol '__of_translate_address' was not declared. Should it be static?
fdt_support.c:1154:5: error: symbol 'fdt_translate_address' redeclared with different type (originally declared at include/fdt_support.h:95) - incompatible argument 3 (different base types)
fdt_support.c: In function 'fdt_node_offset_by_compat_reg':
fdt_support.c:1173:17: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
See also linux kernel commit 0131d897 "of/address: use proper
endianess in get_flags".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
and, if including libfdt.h which includes libfdt_env.h in
the correct order, don't include fdt.h before libfdt.h.
this is needed to get the fdt type definitions set from
the project environment before fdt.h uses them.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
Move these fields into arch_global_data and tidy up. The bExtUart field
does not appear to be used, so punt it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these fields into arch_global_data and tidy up. This is needed for
both ppc and m68k since they share the i2c driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these fields into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update for bsc9132qds.c, b4860qds.c]
Signed-off-by: Tom Rini <trini@ti.com>
Move vco_out, cpm_clk, scc_clk, brg_clk into arch_global_data and tidy
up. Leave pci_clk on its own since this should really depend only on
CONFIG_PCI and not any particular chip type.
Signed-off-by: Simon Glass <sjg@chromium.org>
PPC has several of these fields, selected by chip type, although only one
is ever compiled in.
Instead, use a single field. It would be nice if this could be selected
by CONFIG_PCI, but some chips (e.g. mpc5xxx) use pci_clk even when
CONFIG_PCI is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
We plan to move architecture-specific data into a separate structure so
that we can make the rest of it common.
As a first step, create struct arch_global_data to hold these fields.
Initially it is empty.
This patch applies to all archs at once. I can split it if this is really
a pain.
Signed-off-by: Simon Glass <sjg@chromium.org>
When CoreNet Fabric (CCF) internal resources are consumed by the cores,
inbound SRIO messaging traffic through RMan can put the device into a
deadlock condition.
This errata workaround forces internal resources to be reserved for
upstream transactions. This ensures resources exist on the device for
upstream transactions and removes the deadlock condition.
The Workaround is for the T4240 silicon rev 1.0.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If property 'fsl,sec-era' is already present, it is updated.
This property is required so that applications can ascertain which
descriptor commands are supported on a particular CAAM version.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Configuring custom memory init value using CONFIG_MEM_INIT_VALUE in
the board config file doesn't work and memory is always initialized
to the value 0xdeadbeef. Only use this default value if a board doesn't
define CONFIG_MEM_INIT_VALUE.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
e6500 implements MMUv2 and supports power-of-2 page sizes rather than
power-of-4. Add support for such pages.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The BSC9132 is a highly integrated device that targets the evolving
Microcell, Picocell, and Enterprise-Femto base station market subsegments.
The BSC9132 device combines Power Architecture e500 and DSP StarCore SC3850
core technologies with MAPLE-B2P baseband acceleration processing elements
to address the need for a high performance, low cost, integrated solution
that handles all required processing layers without the need for an
external device except for an RF transceiver or, in a Micro base station
configuration, a host device that handles the L3/L4 and handover between
sectors.
The BSC9132 SoC includes the following function and features:
- Power Architecture subsystem including two e500 processors with
512-Kbyte shared L2 cache
- Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte private L2
cache
- 32 Kbyte of shared M3 memory
- The Multi Accelerator Platform Engine for Pico BaseStation Baseband
Processing (MAPLE-B2P)
- Two DDR3/3L memory interfaces with 32-bit data width (40 bits including
ECC), up to 1333 MHz data rate
- Dedicated security engine featuring trusted boot
- Two DMA controllers
- OCNDMA with four bidirectional channels
- SysDMA with sixteen bidirectional channels
- Interfaces
- Four-lane SerDes PHY
- PCI Express controller complies with the PEX Specification-Rev 2.0
- Two Common Public Radio Interface (CPRI) controller lanes
- High-speed USB 2.0 host and device controller with ULPI interface
- Enhanced secure digital (SD/MMC) host controller (eSDHC)
- Antenna interface controller (AIC), supporting four industry
standard JESD207/four custom ADI RF interfaces
- ADI lanes support both full duplex FDD support & half duplex TDD
- Universal Subscriber Identity Module (USIM) interface that
facilitates communication to SIM cards or Eurochip pre-paid phone
cards
- Two DUART, two eSPI, and two I2C controllers
- Integrated Flash memory controller (IFC)
- GPIO
- Sixteen 32-bit timers
Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds the ability for the FSL DDR interactive debugger to
automatically run the sequence of commands stored in the ddr_interactive
environment variable. Commands are separated using ';'.
ddr_interactive=compute; edit c0 d0 dimmparms caslat_X 0x3FC0; go
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add copy command which allows copying of DIMM/controller settings.
This saves tedious retyping of parameters for each identical DIMM
or controller.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This fix allows the name of the stage to be specifed after the
controler and DIMM is specified. Prior to this fix, if the
data stage name is not the first entry on the command line,
the operation is applied to all controller and DIMMs.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Move the FSL DDR prompt command parsing to a separate function
so that it can be reused.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Using environmental variable "ddr_interactive" to activate interactive DDR
debugging seomtiems is not enough. For example, after updating SPD with a
valid but wrong image, u-boot won't come up due to wrong DDR configuration.
By enabling key press method, we can enter debug mode to have a chance to
boot without using other tools to recover the board.
CONFIG_FSL_DDR_INTERACTIVE needs to be defined in header file. To enter the
debug mode by key press, press key 'd' shortly after reset, like one would
do to abort auto booting. It is fixed to lower case 'd' at this moment.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Different personalities/derivatives of SoC may have reduced cluster. But it is
not necessary for last valid DCFG_CCSR_TP_CLUSTER register to have
DCFG_CCSR_TP_CLUSTER[EOC] bit set to represent "End of Clusters".
EOC bit can still be set in last DCFG_CCSR_TP_CLUSTER register of orignal SoC
which may not be valid for the personality.
So add initiator type check to find valid cluster.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The boot page in memory is already reserved so OS won't overwrite.
As long as the boot page translation is active, the default boot page
also needs to be reserved in case the memory is 4GB or more.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This adds arch support for PPC mpc83xx to boot "minimal" (4K) SPLs
using the new infrastructure.
Existing nand_spl targets are updated to deal with the name change
from nand_init.c to spl_minimal.c (as in theory this isn't limited
to NAND anymore).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Move the getenv_yesno() to env_common.c and change most checks for
'y' or 'n' to use this helper.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
strncasecmp() is present as strnicmp() but disabled. Make it available
and define strcasecmp() also. There is a only a small performance penalty
to having strcasecmp() call strncasecmp(), so do this instead of a
standalone function, to save code space.
Update the prototype in arch-specific headers as needed to avoid warnings.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch enables the SPL framework to be used on powerpc platforms
and not only ARM.
timer_init() does not exist on PPC systems. The timer (decrementer) is
initialized and enabled in interrupt_init() here. And currently
interrupt_init() is called after relocation to SDRAM. Since the only
powerpc SPL implementation (a3m071) doesn't need a timer, let's remove
this timer_init() call for PPC systems.
Signed-off-by: Stefan Roese <sr@denx.de>
By extracting these defines into a header, they can be re-used by other
C sources as well. This will be done by the SPL framework OS boot
support.
Signed-off-by: Stefan Roese <sr@denx.de>
Fix a bug introduced by this patch
powerpc/mpc85xx: Temporary fix for spin table backward compatibility
Should have checked both CONFIG_PPC_SPINTABLE_COMPATIBLE and CONFIG_MP in
cpu_init.c.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The documented work-around for P4080 erratum SERDES-9 has been updated.
It is now compatible with the work-around for erratum A-4580.
This requires adding a few bitfield macros for the BnTTLCRy0 register.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Due to SerDes configuration error, if we set the PCI-e controller link width
as x8 in RCW and add a narrower width(such as x4, x2 or x1) PCI-e device to
PCI-e slot, it fails to train down to the PCI-e device's link width. According
to p4080ds errata PCIe-A003, we reset the PCI-e controller link width to x4 in
u-boot. Then it can train down to x2 or x1 width to make the PCI-e link between
RC and EP.
Signed-off-by: Yuanquan Chen <B41889@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
board configuration file is included before asm/config_mpc85xx.h.
however, CONFIG_FSL_SATA_V2 is defined in asm/config_mpc85xx.h.
it will never take effective in the board configuration file for
this kind of code :
#ifdef CONFIG_FSL_SATA_V2
...
#endif
To solve this problem, move CONFIG_FSL_SATA_V2 to board
configuration header file.
This patch reverts Timur's
commit:3e0529f742e893653848494ffb9f7cd0d91304bf
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The work-around for erratum A-004580 ("Internal tracking loop can falsely
lock causing unrecoverable bit errors") is implemented via the PBI
(pre-boot initialization code, typically attached to the RCW binary).
This is because the work-around is easier to implement in PBI than in
U-Boot itself.
It is still useful, however, for the 'errata' command to tell us whether
the work-around has been applied. For A-004580, we can do this by verifying
that the values in the specific registers that the work-around says to
update.
This change requires access to the SerDes lane sub-structure in
serdes_corenet_t, so we make it a named struct.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
by moving compat_strlist into the .bss section.
0xfe004d80 fdt_fixup_crypto_node [u-boot]: 264
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Once u-boot sets the spin table to cache-enabled memory, old kernel which
uses cache-inhibit mapping without coherence will not work properly. We
use this temporary fix until kernel has updated its spin table code.
For now this fix is activated by default. To disable this fix for new
kernel, set environmental variable "spin_table_compat=no". After kernel
has updated spin table code, this default shall be changed.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The work-around for erratum A-004849 ("CoreNet fabric (CCF) can exhibit a
deadlock under certain traffic patterns causing the system to hang") is
implemented via the PBI (pre-boot initialization code, typically attached
to the RCW binary). This is because the work-around is easier to implement
in PBI than in U-Boot itself.
It is still useful, however, for the 'errata' command to tell us whether
the work-around has been applied. For A-004849, we can do this by verifying
that the values in the specific registers that the work-around says to
update.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P5040 has an e5500 core, so CONFIG_SYS_PPC64 should be defined in
config_mpc85xx.h. This macro was absent in the initial P5040 patch because
it crossed paths with the patch that introduced the macro.
Also delete CONFIG_SYS_FSL_ELBC_MULTIBIT_ECC, since it's not used in the
upstream U-Boot. It's a holdover from the SDK.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There were a number of shared files that were using
CONFIG_SYS_MPC85xx_DDR_ADDR, or CONFIG_SYS_MPC86xx_DDR_ADDR, and
several variants (DDR2, DDR3). A recent patchset added
85xx-specific ones to code which was used by 86xx systems.
After reviewing places where these constants were used, and
noting that the type definitions of the pointers assigned to
point to those addresses were the same, the cleanest approach
to fixing this problem was to unify the namespace for the
85xx, 83xx, and 86xx DDR address definitions.
This patch does:
s/CONFIG_SYS_MPC8.xx_DDR/CONFIG_SYS_MPC8xxx_DDR/g
All 85xx, 86xx, and 83xx have been built with this change.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Andy Fleming <afleming@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Update CONFIG_RAMBOOT and CONFIG_NAND_SPL references to accept CONFIG_SPL
and CONFIG_SPL_BUILD, respectively. CONFIG_NAND_SPL can be removed once
the last mpc85xx nand_spl target is gone.
CONFIG_RAMBOOT will need to remain for other use cases, but it doesn't
seem right to overload it for meaning SPL as well as nand_spl does. Even
if it's somewhat appropriate for the main u-boot, the SPL itself isn't
(necessarily) ramboot, and we don't have separate configs for SPL and
main u-boot. It was also inconsistent, as other platforms such as
mpc83xx didn't use CONFIG_RAMBOOT in this way.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
cpu_init_nand.c is renamed to spl_minimal.c as it is not really NAND-specific.
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: factor out START, and change cpu_init_nand.c to spl_minimal.c
Cc: Andy Fleming <afleming@freescale.com>
A subsequent patch will conditionalize some of the files that are
currently unconditional.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
It applies to non-Freescale 85xx boards as well as Freescale boards,
so it doesn't belong in board/freescale. Plus, it needs to come out
of nand_spl if it's to be used by the new SPL.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
It's arch code and not a driver, so move it where it belongs. When it
originally went into drivers/misc there was no 8xxx CPU directory.
This will make new-SPL support a little easier since we can keep the CPU
stuff together and not need to pull stuff in from drivers/misc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
In the RAMBOOT/SPL case we were creating a TLB entry starting at
CONFIG_SYS_MONITOR_BASE, and just hoping that the base was properly
aligned for the TLB entry size. This turned out to not be the case
with NAND SPL because the main U-Boot starts at an offset into the image
in order to skip the SPL itself.
Fix the TLB entry to always start at a proper alignment. We still assume that
CONFIG_SYS_MONITOR_BASE doesn't start immediately before a large-page boundary
thus requiring multiple TLB entries.
Signed-off-by: Scott Wood <scottwood@frescale.com>
Cc: Andy Fleming <afleming@freescale.com>
This was introduced by commit 2446151974, but it
fails in a minimal SPL build where the only thing in arch/powerpc/lib is
cache.c, which apparently doesn't generate any fixup records.
The problem is reported to occur with GCC 3.x, so insist on GCC 4.0 or newer.
Patterned after checkthumb as suggested by Tom Rini.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Tom Rini <trini@ti.com>
--
v2: test gcc version instead of testing nothing
Now outputs like this:
L2: 512 KB already enabled, moving to 0xf8f80000
rather than this:
L2: 512 KB already enabledmoving to 0xf8f80000
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Previously, in many if not all configs we were creating overlapping TLB entries
which is illegal. This caused a crash during boot when moving p2020rdb NAND SPL
into L2 SRAM.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
--
Prabhakar, please test that debug still works.
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.
As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is no point to put speed into
pipe anymore so it's removed and a bunch of host drivers fixed to
look at usb_device->speed instead.
Old usbdescriptors.h included is not removed as it seems to be
used by old USB device code.
This makes usb.h and usbdevice.h incompatible. Fortunately the
only place that tries to include both are the old MUSB code and
it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute
on musb_regs structure but this attribute seems to be unneeded
(old MUSB code doesn't support any DMA at all).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
fdt.c:91:78: warning: Using plain integer as NULL pointer
fdt.c:103:78: warning: Using plain integer as NULL pointer
speed.c:55:11: warning: symbol 'corecnf_tab' was not declared. Should it be static?
speed.c:519:5: warning: symbol 'do_clocks' was not declared. Should it be static?
mpc8313erdb.c:73:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:74:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:75:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:76:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:79:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:80:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:81:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:82:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:85:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:86:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:87:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:88:17: warning: obsolete struct initializer, use C99 syntax
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
fsl_corenet_serdes.c:485:6: warning: symbol '__soc_serdes_init' was not declared. Should it be static?
cpu_init.c:185:6: warning: symbol 'invalidate_cpc' was not declared. Should it be static?
bcsr.c:28:27: warning: non-ANSI function declaration of function 'enable_8568mds_duart'
bcsr.c:39:33: warning: non-ANSI function declaration of function 'enable_8568mds_flash_write'
bcsr.c:46:34: warning: non-ANSI function declaration of function 'disable_8568mds_flash_write'
bcsr.c:53:29: warning: non-ANSI function declaration of function 'enable_8568mds_qe_mdio'
bcsr.c:28:33: warning: non-ANSI function declaration of function 'enable_8569mds_flash_write'
bcsr.c:33:34: warning: non-ANSI function declaration of function 'disable_8569mds_flash_write'
bcsr.c:38:28: warning: non-ANSI function declaration of function 'enable_8569mds_qe_uec'
bcsr.c:63:47: warning: non-ANSI function declaration of function 'disable_8569mds_brd_eeprom_write_protect'
ngpixis.c:245:1: error: directive in argument list
ngpixis.c:247:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
ctrl_regs.c:31:5: warning: symbol 'fsl_ddr_get_version' was not declared. Should it be static?
cpu.c:135:14: warning: non-ANSI function declaration of function 'cpu_mask'
cpu.c:154:18: warning: non-ANSI function declaration of function 'cpu_numcores'
cpu.c:37:17: warning: symbol 'cpu_type_list' was not declared. Should it be static?
cpu.c:117:17: warning: symbol 'cpu_type_unknown' was not declared. Should it be static?
fsl_lbc.c:14:6: warning: symbol '__lbc_sdram_init' was not declared. Should it be static?
and:
lc_common_dimm_params.c:15:1: warning: symbol 'compute_cas_latency_ddr3' was not declared. Should it be static?
making it static produces the following compiler warning:
lc_common_dimm_params.c:15:1: warning: 'compute_cas_latency_ddr3' defined but not used [-Wunused-function]
so we protect it with the preprocessor.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
traps.c:*:1: warning: symbol 'print_backtrace' was not declared. Should it be static?
traps.c:93:1: warning: symbol '_exception' was not declared. Should it be static?
board.c:166:6: warning: symbol '__board_add_ram_info' was not declared. Should it be static?
board.c:174:5: warning: symbol '__board_flash_wp_on' was not declared. Should it be static?
board.c:187:6: warning: symbol '__cpu_secondary_init_r' was not declared. Should it be static?
board.c:265:12: warning: symbol 'init_sequence' was not declared. Should it be static?
board.c:348:5: warning: symbol '__fixup_cpu' was not declared. Should it be static?
board.c:405:53: warning: Using plain integer as NULL pointer
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
extable.c:66:9: warning: symbol 'ex_tab_message' was not declared. Should it be static?
making it static can produce a new build warning on some boards:
extable.c:66:12: warning: 'ex_tab_message' defined but not used [-Wunused-variable]
but ex_tab_message doesn't do much even when used, so just remove it.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
a fixup __iomem definition in arch code appears to be placed there as a cover
up from a code import from linux when u-boot didn't yet have a compiler.h,
introduced by commit 812711ce6b "Implement
__raw_{read,write}[bwl] on all architectures".
git show 812711ce6b3a386125dcf0d6a59588e461abbb87:include/linux/compiler.h
fatal: Path 'include/linux/compiler.h' exists on disk, but not in '812711ce6b3a386125dcf0d6a59588e461abbb87'.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
u-boot's byteorder headers did not contain endianness attributions
for use with sparse, causing a lot of false positives. Import the
kernel's latest definitions, and enable them by including compiler.h
and types.h. They come with 'const' added for some swab functions, so
fix those up, too:
include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default]
Also, note: u-boot's historic __BYTE_ORDER definition has been
preserved (for the time being at least).
We also remove ad-hoc barrier() definitions, since we're including
compiler.h in files that hadn't in the past:
macb.c:54:0: warning: "barrier" redefined [enabled by default]
In addition, including compiler.h in byteorder changes the 'noinline'
definition to expand to __attribute__((noinline)). This fixes
arch/powerpc/lib/bootm.c:
bootm.c:329:16: error: attribute '__attribute__': unknown attribute
bootm.c:329:16: error: expected ')' before '__attribute__'
bootm.c:329:25: error: expected identifier or '(' before ')' token
powerpc sparse builds yield:
include/common.h:356:22: error: marked inline, but without a definition
the unknown-reason inlining without a definition is considered obsolete
given it was part of the 2002 initial commit, and no arm version was
'fixed.'
also fixed:
ydirectenv.h:60:0: warning: "inline" redefined [enabled by default]
and:
Configuring for devconcenter - Board: intip, Options: DEVCONCENTER
make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1
make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2
powerpc-fsl-linux-size: './u-boot': No such file
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available
4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here
and:
In file included from crc32.c:50:0:
crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration]
crc32table.h:4:1: error: initializer element is not constant
crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]')
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[trini: Remove '#endif' in include/common.h around setenv portion]
Signed-off-by: Tom Rini <trini@ti.com>
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years. Get rid of the dead
weight.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
This processor, though very similar to other members of the
PowerQUICC II Pro family (namely 8308, 8360 and 832x), provides
yet another feature set than any supported sibling.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Introduce a new configuration token CONFIG_MPC830x to be shared among
mpc8308 and mpc8309. Define it for existing 8308 boards, and refactor
existing common code so to make future introduction of 8309 simpler.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
simplify #if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832x)
for qe variables
with #if defined(CONFIG_QE)
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The timeout_save variable was only used by the DDR111_134
erratum code. It was being set, but never used. Newer compilers
will actually complain about this.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, the SRIO and PCIE boot master module will be compiled into the
u-boot image if the macro "CONFIG_FSL_CORENET" has been defined. And this
macro has been included by all the corenet architecture platform boards.
But in fact, it's uncertain whether all corenet platform boards support
this feature.
So it may be better to get rid of the macro "CONFIG_FSL_CORENET", and add
a special macro for every board which can support the feature. This
special macro will be defined in the header file
"arch/powerpc/include/asm/config_mpc85xx.h". It will decide if the SRIO
and PCIE boot master module should be compiled into the board u-boot image.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Starting from QMan3.0, the QMan clock cycle needs be exposed so that the kernel
driver can use it to calculate the shaper prescaler and rate.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Because QMan3.0 and BMan2.1 used ip_cfg in ip_rev_2 register to differ the
total portal number, buffer pool number etc, we can use this info to limit
those resources in kernel driver.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
New corenet platforms with chassis2 have separated DDR clock inputs. Use
CONFIG_DDR_CLK_FREQ for DDR clock. This patch also cleans up the logic of
detecting and displaying synchronous vs asynchronous mode.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Move spin table to cached memory to comply with ePAPR v1.1.
Load R3 with 64-bit value if CONFIG_SYS_PPC64 is defined.
'M' bit is set for DDR TLB to maintain cache coherence.
See details in doc/README.mpc85xx-spin-table.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
R6 was in ePAPR draft version but was dropped in official spec.
Removing it to comply.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since empty DIMM slot is allowed on other than the first slot, remove the
error message if SPD is not found in this case.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Based on populated DIMMs, automatically select from cs0_cs1_cs2_cs3 or
cs0_cs1 interleaving, or non-interleaving if not available.
Fix the message of interleaving disabled if controller interleaving
is enabled but DIMMs don't support it.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After DDR controller is enabled, it performs a calibration for the
transmit data vs DQS paths. During this calibration, the DDR controller
may make an inaccurate calculation, resulting in a non-optimal tap point.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Boot space translation utilizes the pre-translation address to select
the DDR controller target. However, the post-translation address will be
presented to the selected DDR controller. It is possible that the pre-
translation address selects one DDR controller but the post-translation
address exists in a different DDR controller when using certain DDR
controller interleaving modes. The device may fail to boot under these
circumstances. Note that a DDR MSE error will not be detected since DDR
controller bounds registers are programmed to be the same when configured
for DDR controller interleaving.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When ECC is enabled, DDR controller needs to initialize the data and ecc.
The wait time can be calcuated with total memory size, bus width, bus speed
and interleaving mode. If it went wrong, it is bettert to timeout than
waiting for D_INIT to clear, where it probably hangs.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix handling quad-rank DIMMs in a system with two DIMM slots and first
slot supports both dual-rank DIMM and quad-rank DIMM.
For systems with quad-rank DIMM and double dual-rank DIMMs, cs_config
registers need to be enabled to maintain proper ODT operation. The
inactive CS should have bnds registers cleared.
Fix the turnaround timing for systems with all chip-selects enabled. This
wasn't an issue before because DDR was running lower than 1600MT/s with
this interleaving mode.
Fix DDR address calculation. It wasn't an issue until we have multiple
controllers with each more than 4GB and interleaving is disabled.
It also fixes the message of DDR: 2 GiB (DDR3, 64-bit, CL=0.5, ECC off)
when debugging DDR and first DDR controller is disabled. With the fix,
the first enabled controller information will be displayed.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
DDRC ver 4.7 adds DDR_SLOW bit in sdram_cfg_2 register. This bit needs to be
set for speed lower than 1250MT/s.
CDR1 and CDR2 are control driver registers. ODT termination valueis for
IOs are defined. Starting from DDRC 4.7, the decoding of ODT for IOs is
000 -> Termsel off
001 -> 120 Ohm
010 -> 180 Ohm
011 -> 75 Ohm
100 -> 110 Ohm
101 -> 60 Ohm
110 -> 70 Ohm
111 -> 47 Ohm
Add two write leveling registers. Each QDS now has its own write leveling
start value. In case of zero value, the value of QDS0 will be used. These
values are board-specific and are set in board files.
Extend DDR register timing_cfg_1 to have 4 bits for each field.
DDR control driver registers and write leveling registers are added to
interactive debugging for easy access.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The multirate ethernet media access controller (mEMAC) interfaces to
10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII
interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Freescale B4860 and variant SoCs. Features of B4860 are
(incomplete list):
Six fully-programmable StarCore SC3900 FVP subsystems, divided into three
clusters-each core runs up to 1.2 GHz, with an architecture highly
optimized for wireless base station applications
Four dual-thread e6500 Power Architecture processors organized in one
cluster-each core runs up to 1.8 GHz
Two DDR3/3L controllers for high-speed, industry-standard memory interface
each runs at up to 1866.67 MHz
MAPLE-B3 hardware acceleration-for forward error correction schemes
including Turbo or Viterbi decoding, Turbo encoding and rate matching,
MIMO MMSE equalization scheme, matrix operations, CRC insertion and
check, DFT/iDFT and FFT/iFFT calculations, PUSCH/PDSCH acceleration,
and UMTS chip rate acceleration
CoreNet fabric that fully supports coherency using MESI protocol between
the e6500 cores, SC3900 FVP cores, memories and external interfaces.
CoreNet fabric interconnect runs at 667 MHz and supports coherent and
non-coherent out of order transactions with prioritization and
bandwidth allocation amongst CoreNet endpoints.
Data Path Acceleration Architecture, which includes the following:
Frame Manager (FMan), which supports in-line packet parsing and general
classification to enable policing and QoS-based packet distribution
Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading
of queue management, task management, load distribution, flow ordering,
buffer management, and allocation tasks from the cores
Security engine (SEC 5.3)-crypto-acceleration for protocols such as
IPsec, SSL, and 802.16
RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and
outbound). Supports types 5, 6 (outbound only)
Large internal cache memory with snooping and stashing capabilities for
bandwidth saving and high utilization of processor elements. The
9856-Kbyte internal memory space includes the following:
32 Kbyte L1 ICache per e6500/SC3900 core
32 Kbyte L1 DCache per e6500/SC3900 core
2048 Kbyte unified L2 cache for each SC3900 FVP cluster
2048 Kbyte unified L2 cache for the e6500 cluster
Two 512 Kbyte shared L3 CoreNet platform caches (CPC)
Sixteen 10-GHz SerDes lanes serving:
Two Serial RapidIO interfaces. Each supports up to 4 lanes and a total
of up to 8 lanes
Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue-
less antenna connection
Two 10-Gbit Ethernet controllers (10GEC)
Six 1G/2.5-Gbit Ethernet controllers for network communications
PCI Express controller
Debug (Aurora)
Two OCeaN DMAs
Various system peripherals
182 32-bit timers
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Freescale T4240 SoC. Feature of T4240 are
(incomplete list):
12 dual-threaded e6500 cores built on Power Architecture® technology
Arranged as clusters of four cores sharing a 2 MB L2 cache.
Up to 1.8 GHz at 1.0 V with 64-bit ISA support (Power Architecture
v2.06-compliant)
Three levels of instruction: user, supervisor, and hypervisor
1.5 MB CoreNet Platform Cache (CPC)
Hierarchical interconnect fabric
CoreNet fabric supporting coherent and non-coherent transactions with
prioritization and bandwidth allocation amongst CoreNet end-points
1.6 Tbps coherent read bandwidth
Queue Manager (QMan) fabric supporting packet-level queue management and
quality of service scheduling
Three 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support
Memory prefetch engine (PMan)
Data Path Acceleration Architecture (DPAA) incorporating acceleration for
the following functions:
Packet parsing, classification, and distribution (Frame Manager 1.1)
Queue management for scheduling, packet sequencing, and congestion
management (Queue Manager 1.1)
Hardware buffer management for buffer allocation and de-allocation
(BMan 1.1)
Cryptography acceleration (SEC 5.0) at up to 40 Gbps
RegEx Pattern Matching Acceleration (PME 2.1) at up to 10 Gbps
Decompression/Compression Acceleration (DCE 1.0) at up to 20 Gbps
DPAA chip-to-chip interconnect via RapidIO Message Manager (RMAN 1.0)
32 SerDes lanes at up to 10.3125 GHz
Ethernet interfaces
Up to four 10 Gbps Ethernet MACs
Up to sixteen 1 Gbps Ethernet MACs
Maximum configuration of 4 x 10 GE + 8 x 1 GE
High-speed peripheral interfaces
Four PCI Express 2.0/3.0 controllers
Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz with
Type 11 messaging and Type 9 data streaming support
Interlaken look-aside interface for serial TCAM connection
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Four I2C controllers
Four 2-pin or two 4-pin UARTs
Integrated Flash controller supporting NAND and NOR flash
Two eight-channel DMA engines
Support for hardware virtualization and partitioning enforcement
QorIQ Platform's Trust Architecture 1.1
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The T4 has added devices to previous corenet implementations:
* SEC has 3 more DECO units
* New PMAN device
* New DCE device
This doesn't add full support for the new devices. Just some
preliminary support.
Move PMAN LIODN to upper half of register
Despite having only one LIODN, the PMAN LIODN is stored in the
upper half of the register. Re-use the 2-LIODN code and just
set the LIODN as if the second one is 0. This results in the
actual LIODN being written to the upper half of the register.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Corenet 2nd generation Chassis doesn't have ddr_sync bit in RCW. Only
async mode is supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Create new files to handle 2nd generation Chassis as the registers are
organized differently.
- Add SerDes protocol parsing and detection
- Add support of 4 SerDes
- Add CPRI protocol in fsl_serdes.h
The Common Public Radio Interface (CPRI) is publicly available
specification that standardizes the protocol interface between the
radio equipment control (REC) and the radio equipment (RE) in wireless
basestations. This allows interoperability of equipment from different
vendors,and preserves the software investment made by wireless service
providers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Corenet 2nd generation Chassis has different RCW and registers for SerDes.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The QCSP registers are expanded and moved from offset 0 to offset 0x1000
for SoCs with QMan v3.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Expand the reference clock select to three bits
000: 100 MHz
001: 125 MHz
010: 156.25MHz
011: 150 MHz
100: 161.1328125 MHz
All others reserved
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Corenet based SoCs have different core clocks starting from Chassis
generation 2. Cores are organized into clusters. Each cluster has up to
4 cores sharing same clock, which can be chosen from one of three PLLs in
the cluster group with one of the devisors /1, /2 or /4. Two clusters are
put together as a cluster group. These two clusters share the PLLs but may
have different divisor. For example, core 0~3 are in cluster 1. Core 4~7
are in cluster 2. Core 8~11 are in cluster 3 and so on. Cluster 1 and 2
are cluster group A. Cluster 3 and 4 are in cluster group B. Cluster group
A has PLL1, PLL2, PLL3. Cluster group B has PLL4, PLL5. Core 0~3 may have
PLL1/2, core 4~7 may have PLL2/2. Core 8~11 may have PLL4/1.
PME and FMan blocks can take different PLLs, configured by RCW.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Panic if the number of cores is more than CONFIG_MAX_CPUS because it will
surely overflow gd structure.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Chassis generation 2 has different mask and shift. Use macro instead of
magic numbers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Using E6500 L1 cache as initram requires L2 cache enabled.
Add l2-cache cluster enabling.
Setup stash id for L1 cache as (coreID) * 2 + 32 + 0
Setup stash id for L2 cache as (cluster) * 2 + 32 + 1
Stash id for L2 is only set for Chassis 2.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
These assembly macros simplify codes to add and delete temporary TLB entries.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
FSL_HW_PORTAL_PME is used even when CONFIG_SYS_DPAA_PME is not defined.
Remove the #ifdef.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for the Freescale P5040 SOC, which is similar to the P5020.
Features of the P5040 are:
Four P5040 single-threaded e5500 cores built
Up to 2.4 GHz with 64-bit ISA support
Three levels of instruction: user, supervisor, hypervisor
CoreNet platform cache (CPC)
2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric
Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support Up to 1600MT/s
Memory pre-fetch engine
DPAA incorporating acceleration for the following functions
Packet parsing, classification, and distribution (FMAN)
Queue management for scheduling, packet sequencing and
congestion management (QMAN)
Hardware buffer management for buffer allocation and
de-allocation (BMAN)
Cryptography acceleration (SEC 5.2) at up to 40 Gbps SerDes
20 lanes at up to 5 Gbps
Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces
Two 10 Gbps Ethernet MACs
Ten 1 Gbps Ethernet MACs
High-speed peripheral interfaces
Two PCI Express 2.0/3.0 controllers
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Two I2C controllers
Four UARTs
Integrated flash controller supporting NAND and NOR flash
DMA
Dual four channel
Support for hardware virtualization and partitioning enforcement
Extra privileged level for hypervisor support
QorIQ Trust Architecture 1.1
Secure boot, secure debug, tamper detection, volatile key storage
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add a new device tree property named "fsl,liodn-offset-list"
holding a list of per pci endpoint permitted liodn offsets.
This property is useful in virtualization scenarios
that implement per pci endpoint partitioning.
The final liodn of a partitioned pci endpoint is
calculated by the hardware, by adding these offsets
to pci controller's base liodn, stored in the
"fsl,liodn" property of its node.
The liodn offsets are interleaved to get better cache
utilization. As an example, given 3 pci controllers,
the following liodns are generated for the pci endpoints:
pci0: 193 256 259 262 265 268 271 274 277
pci1: 194 257 260 263 266 269 272 275 278
pci2: 195 258 261 264 267 270 273 276 279
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P5040 does not have SRIO support, so there are no SRIO LIODNs.
Therefore, the functions that set the SRIO LIODNs should not be compiled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The liodn for the new PCIE controller included in P5040DS is no longer set
through a register in the guts register block but with one in the PCIE
register block itself. Update the PCIE CCSR structure to add the new liodn
register and add a new dedicated SET_PCI_LIODN_BASE macro that puts
the liodn in the correct register.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Commit 709389b6 unintentionally used the Unicode version of the
apostrophy. Replace it with the normal ASCII version.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum: A-004034
Affects: SRIO
Description: During port initialization, the SRIO port performs
lane synchronization (detecting valid symbols on a lane) and
lane alignment (coordinating multiple lanes to receive valid data
across lanes). Internal errors in lane synchronization and lane
alignment may cause failure to achieve link initialization at
the configured port width.
An SRIO port configured as a 4x port may see one of these scenarios:
1. One or more lanes fails to achieve lane synchronization.
Depending on which lanes fail, this may result in downtraining
from 4x to 1x on lane 0, 4x to 1x on lane R (redundant lane).
2. The link may fail to achieve lane alignment as a 4x, even
though all 4 lanes achieve lane synchronization, and downtrain
to a 1x. An SRIO port configured as a 1x port may fail to complete
port initialization (PnESCSR[PU] never deasserts) because of
scenario 1.
Impact: SRIO port may downtrain to 1x, or may fail to complete
link initialization. Once a port completes link initialization
successfully, it will operate normally.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix usb device-tree fixup:
- wrong modification of dr_mode and phy_type when
"usb1" is not mentioned inside hwconfig string;
now allows hwconfig strings like:
"usb2:dr_mode=host,phy_type=ulpi"
- add warning message for using usb_dr_mode
and usb_phy_type env variables (if either is used)
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the
workaround conditional.
In formal release document, the errata number should be ESDHC13 instead
of ESDHC136.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We should only write TSR_WIS to the SPRN_TSR register in
reset_85xx_watchdog.
The old code would cause the timer interrupt to be acknowledged when the
watchdog was reset, and we would then get no more timer interrupts.
This bug would affect all mpc85xx boards that have the watchdog enabled.
Signed-off-by: Mark Marshall <Mark.Marshall@omicron.at>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Users of familiar with the Linux gpiolib API expect that value parameter
to gpio_direction_output reflects the initial state of the output pin.
gpio_direction_output was always driving the output low, now it drives
it high or low according to the value provided.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
move most of mpc8xx hooks from cmd_ide.c into ide_preinit() and newly created
ide_init_postreset() (invoked after calling ide_reset after ide_preinit),
some cleanup to make checkpatch happy, enable IDE init hooks in configs of
affected boards.
confusingly, these hooks are used by more than just mpc8xx-based boards, and
therefore are placed in arch/ppc/lib/
note: checkpatch still emits warnings about using volatile
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Replace the in-place ad-hoc implementation of serial_puts() within
the drivers with default_serial_puts() call. This cuts down on the
code duplication quite a bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: James F. Dougherty <jfd@broadcom.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.
Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Marek Vasut <marex@denx.de>
Since the IOP480 (PPC401/3 variant from PLX) is only used on 2
boards that are not actively maintained, lets remove support
for it completely. This way the ppc4xx code will get a bit cleaner.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Marek Vasut <marex@denx.de>
Remove the parts depending either on disabled CONFIG_SERIAL_MULTI
or ifdefs around CONFIG_SERIAL_MULTI parts since CONFIG_SERIAL_MULTI
is now enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Remove the support for not-CONFIG_SERIAL_MULTI part from serial
port drivers and some board files. Since CONFIG_SERIAL_MULTI is
now enabled by default, that part is a dead code. Remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into iop480 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the iop480 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc85xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc85xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into both SCC and SMC mpc8260
serial drivers. These drivers were so far only usable directly, but this
patch also adds support for the multi method. This allows using more than
one serial driver alongside the mpc8260 drivers. Also, add a weak
implementation of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc8220 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc8220 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc5xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc5xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Move the registration of serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented mpc512x_serial_initialize() function, which is
implemented inside of the mpc512x serial driver allows encapsulation
of serialN_device within the mpc512x serial driver itself.
Also, remove the exports of serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the mpx512x serial driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Move the registration of serial_smc and serial_scc ports from
default serial_initialize() into CPU specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The exports of both serial_scc_device and serial_smc_device can
not yet be removed as they are still used in default_serial_console()
calls.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Properly spell out the whole structure member names when an initialized
varible is instantiated from the struct serial_driver. In case the
structure definition for struct serial_driver undergoes reordering,
there will be no impact on variables defined based on this structure.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: C Nauman <cnauman@diagraph.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Michal Simek <monstr@monstr.eu>
Since commit 50a47d0523
(net: punt bd->bi_ip_addr) booting old 2.4.x ppc kernels
is broken due to changed offsets of the fields in struct bd_t.
Offsets of the fields after removed bi_ip_addr are wrong,
causing wrong bus clocks and console baudrate configurations
and various other issues. Re-add the bi_ip_addr field to preserve
backward compatibility with older ppc kernels. Setting bi_ip_addr
in board.c is not really needed, grepping in the 2.4 linux tree
shows that bi_ip_addr is not accessed there. Adding bi_ip_addr
to struct bd_t for other arches isn't needed it seems. bd_t is
not used by other arches in the 2.4 linux tree.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
wait_ticks() calls get_ticks() without building a back chain which
makes gdb unhappy when doing back trace. This can also cause
improper memory accesses.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Instead of just shooting down the entry that covers CCSR, clear out
every TLB entry that isn't the one that we're executing out of.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Before proper environment is setup, we extract hwconfig and put it into a
buffer with size HWCONFIG_BUFFER_SIZE. We need to enlarge the buffer to
accommodate longer string. Since this macro is used in multiple files, we
move it into arch/powerpc/include/asm/config.h.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add one more argument to call function readline_into_buffer().
Fix print SPD format for negative values.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Only the first DIMM of first controller should fall back to raw timing
parameters if SPD is missing or corrupted.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Empty slot should be skipped when calculating CAS latency.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Faster DDR3 timing requires parameters exceeding previously defined
range. Extended parameters are fixed. Added some debug messages.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Restructure DDR interleaving option to support 3 and 4 DDR controllers
for 2-, 3- and 4-way interleaving.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Required by JEDEC 79-3E for high speed DDR3.
Also change "CSn disabled" message to debug.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When the DDR3 speed goes higher, we need to utilize fine offset
from SPD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some debug registers have non-zero default out of reset. If software is
not setting debug registers, skip writing to them to avoid unnecessary
overriding.
Also add debug messages for workarounds and debug registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For the cores with multiple threads, we need to figure out which physical
core a thread belongs. To match the core ids, update PIR registers and
spin tables.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In case more than 32 bit address is used, the EXT bit should be set.
Need to fix up address map for IFC #CS for 4, also need to move # of IFC
banks into config_mpc85xx.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We have actual topology infomation to find out exactly which core is present.
Calculate the number of cores if not specified.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Freescale's High-End SoC are going to have Integrated Flash controller
(IFC)'s support.
So add IFC LAW target ID support for High-End SoC or corenet SoC.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG). Need to define define
CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.
Enable missed e500v2 SoC i.e. MPC8536, MPC8544, MPC8548 and MPC8572 for
debug support.
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum A004510 says that under certain load conditions, modified
cache lines can be discarded, causing data corruption.
To work around this, several CCSR and DCSR register updates need to be
made in a careful manner, so that there is no other transaction in
corenet when the update is made.
The update is made from a locked cacheline, with a delay before to flush
any previous activity, and a delay after to flush the CCSR/DCSR update.
We can't use a readback because that would be another corenet
transaction, which is not allowed.
We lock the subsequent cacheline to prevent it from being fetched while
we're executing the previous cacheline. It is filled with nops so that a
branch doesn't cause us to fetch another cacheline.
Ordinarily we are running in a cache-inhibited mapping at this point, so
we temporarily change that. We make it guarded so that we should never
see a speculative load, and we never do an explicit load. Thus, only the
I-cache should ever fill from this mapping, and we flush/unlock it
afterward. Thus we should avoid problems from any potential cache
aliasing between inhibited and non-inhibited mappings.
NOTE that if PAMU is used with this patch, it will need to use a
dedicated LAW as described in the erratum. This is the responsibility
of the OS that sets up PAMU.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
These are not supported as individual build targets, but instead
are supported by another target.
The dead p4040 defines in particular had bitrotted significantly.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Unlike previous SOCs, the Freescale P5040 has a fifth DTSEC on the second
Fman, so add the Fman and SerDes macros for that DTSEC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, for NAND boot for the P1010/4RDB we hard code the DDR
configuration. We can still dynamically set the DDR bus width in
the nand spl so the P1010/4RDB boards can boot from the same
u-boot image
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
P1015 is the same as P1011 and P1016 is the same as P1012 from software
point of view. They have different packages but share SVRs.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For the powerpc processors with PCIE interface, boot location can be
configured from one PCIE interface by RCW. The processor booting from PCIE
can do without flash for u-boot image. The image can be fetched from another
processor's memory space by PCIE link connected between them.
The processor booting from PCIE is slave, the processor booting from normal
flash memory space is master, and it can help slave to boot from master's
memory space.
When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.
Environment and requirement:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image is in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure PCIE system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to one PCIE interface by RCW.
3. RCW should configure the SerDes, PCIE interfaces correctly.
4. Must set all the cores in holdoff by RCW.
5. Must be powered on before master's boot.
For the master module, need to finish these processes:
1. Initialize the PCIE port and address space.
2. Set inbound PCIE windows covered slave's u-boot image stored in
master's NOR flash.
3. Set outbound windows in order to configure slave's registers
for the core's releasing.
4. Should set the environment variable "bootmaster" to "PCIE1", "PCIE2"
or "PCIE3" using the following command:
setenv bootmaster PCIE1
saveenv
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When compile the slave image for boot from SRIO, no longer need to
specify which SRIO port it will boot from. The code will get this
information from RCW and then finishes corresponding configurations.
This has the following advantages:
1. No longer need to rebuild an image when change the SRIO port for
boot from SRIO, just rewrite the new RCW with selected port,
then the code will get the port information by reading new RCW.
2. It will be easier to support other boot location options, for
example, boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Get rid of the SRIOBOOT_MASTER build target, and to support for serving as
a SRIO boot master via environment variable. Set the environment variable
"bootmaster" to "SRIO1" or "SRIO2" using the following command:
setenv bootmaster SRIO1
saveenv
The "bootmaster" will enable the function of the SRIO boot master, and
this has the following advantages compared with SRIOBOOT_MASTER build
configuration:
1. Reduce a build configuration item in boards.cfg file.
No longer need to build a special image for master, just use a
normal target image and set the "bootmaster" variable.
2. No longer need to rebuild an image when change the SRIO port for
boot from SRIO, just set the corresponding value to "bootmaster"
based on the using SRIO port.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This erratum applies to the following SoCs:
P4080 rev 1.0, 2.0, fixed in rev 3.0
P2041 rev 1.0, 1.1, fixed in rev 2.0
P3041 rev 1.0, 1.1, fixed in rev 2.0.
Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround
may degrade performance. P4080 erratum CPU22 shares the same workaround.
So it is always enabled for P4080. For other SoCs, it can be disabled by
hwconfig with syntax:
fsl_cpu_a011:disable
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The code first aligns the SP to 16 then subtract 8, making it
8 bytes aligned. Furthermore the initial stack frame not
quite correct either.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Andy Fleming <afleming@freescale.com>
PowerPC mandates SP to be 16 bytes aligned.
Furthermore, a stack frame is added, pointing to the reset vector
which may in the way when gdb is walking the stack because
the reset vector may not accessible depending on emulator settings.
Also use a temp register so gdb doesn't pick up intermediate values.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prototype declaration of I/O operation functions are not correct. as both
'extern' and function definition are at same place.
Chage protoype declaration as static.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Return type of in_8, in_be16 and in_le16 should not be'int'. Update it to type
u8/u16/u32.
Although 'unsigned' for in_be32 and in_le32 is correct. But to make return type
uniform across the file changed to u32
Similarly, parameter passed to out_8, out_be16, out_le16 ,out_be32 & out_le32
should not be 'int'.Change it to type u8/u16/u32.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
All the global flag defines are the same across all arches. So unify them
in one place, and add a simple way for arches to extend for their needs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SET_PCI_LIODN() macro takes a compatible property string as a parameter, so that it knows
which PCI device tree node to look for. The calls to these macros are using a hard-coded string,
but we already have the CONFIG_SYS_FSL_PCIE_COMPAT macro which contains the same string, so we
should use that.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Commit 48f6a5c34 removed E bit. BSC9130/1 were left out due to patch apply
timing. Remove them now.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The BR_PHYS_ADDR(x) macro was missing parentheses around "x" in the macro
definition, so callers had to supply their own parenthesis.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
fsl_ddr_get_dimm_params() should be wrapped by
CONFIG_SYS_DDR_RAW_TIMING, otherwise, when using fixed_sdram() instead of
using SPD, it will cause compile error.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The fix for errata workaround is to avoid covering physical address
0xff000000 to 0xffffffff during the implementation. Early commit eb672e92
works until DDR size exceeds 4GB. This fix works for DDR size up to 64GB.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
* 'next' of git://git.denx.de/u-boot:
MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
doc: cleanup - move board READMEs into respective board directories
net: sh_eth: add support for SH7757's GETHER
net: sh_eth: modify the definitions of regsiter
net: sh_eth: add SH_ETH_TYPE_ condition
net: sh_eth: clean up for the SH7757's code
net: fec_mxc: Fix MDC for xMII
net: fec_mxc: Fix setting of RCR for xMII
net: nfs: make NFS_TIMEOUT configurable
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
cpu.c: In function ‘check_CPU’:
cpu.c:256:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Subject slightly changed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested on TQM855MDCBAB7-T66.102 (MPC855T at 66 MHz) and
TQM860LDB0A3-T50.202 (MPC860T at 50MHz).
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
An empty flush_dcache_range() was added into MPC83xx and MPC85xx to
work with drivers shared with other architecture. However, it is
compiled only if USB is set, but it is required for other drivers
(FSL_ESDHC), too.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Andy Fleming <afleming@gmail.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Marek Vasut <marex@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Added MPC83xx version.
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/mpc85xx: Fix Handling the lack of L2 cache on P2040/P2040E
powerpc/mpc85xx: Workaround for erratum CPU_A011
powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
powerpc/P4080: Check SVR for CPU22 workaround
lib/powerpc: addrmap_phys_to_virt() should return a pointer
powerpc/85xx: clean up P1022DS board configuration header file
powerpc/85xx: fdt_set_phy_handle() should return an error code
powerpc/85xx: minor clean-ups to the P2020DS board header file
powerpc/p1010rdb: add readme document for p1010rdb
powerpc/mpc85xx:NAND_SPL:Avoid IFC/eLBC Base address setting
powerpc/mpc85xx:Add debugger support for e500v2 SoC
powerpc/85xx:Fix NAND code base to support debugger
powerpc/85xx:Make debug exception vector accessible
powerpc/85xx:Fix MSR[DE] bit in MSR to support debugger
PATCH 1/4][v4] doc:Add documentation for e500 external debugger support
powerpc/p1010rdb: update mux config of p1010rdb board
powerpc/mpc85xx:Add BSC9131 RDB Support
powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
powerpc/85xx: Add USB device-tree fixup for various platforms
Signed-off-by: Wolfgang Denk <wd@denx.de>
Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.
Signed-off-by: York Sun <yorksun@freescale.com>
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.
Signed-off-by: York Sun <yorksun@freescale.com>
addrmap_phys_to_virt() converts a physical address (phys_addr_t) to a
virtual address, so it should return a pointer instead of an unsigned long.
Its counterpart, addrmap_virt_to_phys(), takes a pointer, so now they're
orthogonal.
The only caller of addrmap_phys_to_virt() converts the return value to
a pointer anyway.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
During NAND_SPL boot, base address and different register are programmed
default by corresponding NAND controllers(eLBC/IFC). These settings are
sufficient enough for NAND SPL.
Avoid updating these register.They will be programmed during NAND RAMBOOT.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG).
So define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.
Please refer doc/README.mpc85xx for more information
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Update NAND code base to ovecome e500 and e500v2's second limitation i.e. IVPR
+ IVOR15 should be valid fetchable OP code address.
As NAND SPL does not compile vector table so making sure IVOR + IVOR15 points to
any fetchable valid data
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Debugging of e500 and e500v1 processer requires debug exception vecter (IVPR +
IVOR15) to have valid and fetchable OP code.
1) While executing in translated space (AS=1), whenever a debug exception is
generated, the MSR[DS/IS] gets cleared i.e. AS=0 and the processor tries to
fetch an instruction from the debug exception vector (IVPR + IVOR15); since now
we are in AS=0, the application needs to ensure the proper TLB configuration to
have (IVOR + IVOR15) accessible from AS=0 also.
Create a temporary TLB in AS0 to make sure debug exception verctor is
accessible on debug exception.
2) Just after relocation in DDR, Make sure IVPR + IVOR15 points to valid opcode
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Debugging of e500 and e500v1 processer requires MSR[DE] bit to be set always.
Where MSR = Machine State register
Make sure of MSR[DE] bit is set uniformaly across the different execution
address space i.e. AS0 and AS1.
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Catalin Udma <catalin.udma@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
- BSC9131 is integrated device that targets Femto base station market.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
- BSC9130 is exactly same as BSC9131 except that the max e500v2
core and DSP core frequencies are 800M(these are 1G in case of 9131).
- BSC9231 is similar to BSC9131 except no MAPLE
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte shared
L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network acceleration
including IEEE 1588. v2 hardware support and virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single port)
and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
This patch takes care of code pertaining to power side functionality only.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
The misspelling of "semiconductor" causes some internal copyright analysis
tools to complain.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch conditionally defines flush_dcache_range() and
invalidate_dcache_range() on MPC8xxx, to avoid EHCI complaining,
resulting in the following output:
$ ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- ./MAKEALL MPC8572DS
Configuring for MPC8572DS board...
make: *** [u-boot] Error 1
powerpc-linux-gnu-size: './u-boot': No such file
e1000.c: In function ‘e1000_initialize’:
e1000.c:5264:13: warning: assignment from incompatible pointer type [enabled by default]
tsec.c: In function ‘tsec_initialize’:
tsec.c:638:12: warning: assignment from incompatible pointer type [enabled by default]
drivers/usb/host/libusb_host.o: In function `ehci_td_buffer':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:186: undefined reference to `flush_dcache_range'
drivers/usb/host/libusb_host.o: In function `ehci_submit_async':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:346: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:348: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:349: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:372: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:374: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:376: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:386: undefined reference to `invalidate_dcache_range'
make: *** [u-boot] Error 1
--------------------- SUMMARY ----------------------------
Boards compiled: 1
Boards with errors: 1 ( MPC8572DS )
----------------------------------------------------------
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Fix this:
ether_scc.c: In function 'mpc82xx_scc_enet_initialize':
ether_scc.c:377:14: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ether_fcc.c: In function 'fec_initialize':
ether_fcc.c:453:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ether_fcc.c: In function 'fec_initialize':
ether_fcc.c:390:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
fec.c: In function 'mpc8220_fec_recv':
fec.c:791:9: warning: passing argument 1 of 'NetReceive' discards qualifiers from pointer target type
include/net.h:438:13: note: expected 'uchar *' but argument is of type 'volatile uchar *'
fec.c: In function 'mpc8220_fec_initialize':
fec.c:839:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Commit db288a9 "net: Remove volatile from net API" caused a number of
build warnings:
fec.c: In function 'fec_initialize':
fec.c:183:13: warning: assignment from incompatible pointer type [enabled by default]
fec.c: In function 'fec_recv':
fec.c:284:5: warning: passing argument 1 of 'NetReceive' discards 'volatile' qualifier from pointer target type [enabled by default]
/home/wd/git/u-boot/work/include/net.h:433:13: note: expected 'uchar *' but argument is of type 'volatile uchar *'
scc.c: In function 'scc_initialize':
scc.c:85:14: warning: assignment from incompatible pointer type [enabled by default]
Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
* 'master' of git://git.denx.de/u-boot-nand-flash:
NAND: Remove ONFI detection message to from bootup log
driver/mtd:IFC: Fix possible memory leak
driver/mtd: IFC NAND: Add support of ONFI NAND flash
mtd, nand: move some printfs to debug output.
nand_util: correct YAFFS image write function
powerpc/85xx: fix NAND boot linker scripts for -fpic
nand: extend .raw accesses to work on multiple pages
GOT is now handled the way the main u-boot.lds does it. Without this,
the boot hangs when built with newer GCC (since 4.6). Older toolchains
hid the issue by converting -fpic to -fPIC.
Signed-off-by: Scott Wood <scottwood@freescale.com>
All arches init this the same way, so move the logic into the core
net code to avoid duplicating it everywhere else.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This field gets read in one place (by "bdinfo"), and we can replace
that with getenv("ipaddr"). After all, the bi_ip_addr field is kept
up-to-date implicitly with the value of the ipaddr env var.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The CCSR relocation code in start.S writes to MAS7 on all e500 parts, but
that register does not exist on e500v1.
Signed-off-by: Timur Tabi <timur@freescale.com>
When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.
Master needs to:
1. Set outbound SRIO windows in order to configure slave's registers
for the core's releasing.
2. Check the SRIO port status when release slave core, if no errors,
will implement the process of the slave core's releasing.
Slave needs to:
1. Set all the cores in holdoff by RCW.
2. Be powered on before master's boot.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ENV can be stored in master's memory space,
then slave can fetch the ENV through SRIO interface.
NOTE: Because the slave can not erase, write master's NOR flash by SRIO
interface, so it can not modify the ENV parameters stored in
master's NOR flash using "saveenv" or other commands.
Master needs to:
1. Put the slave's ENV into it's own memory space.
2. Set an inbound SRIO window covered slave's ENV stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode and ENV from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ucode can be stored in master's memory space,
then slave can fetch the ucode image through SRIO interface. For the
corenet platform, ucode is for Fman.
Master needs to:
1. Put the slave's ucode image into it's own memory space.
2. Set an inbound SRIO window covered slave's ucode stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.
The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure SRIO switch system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to SRIO1 or SRIO2 by RCW.
3. RCW should configure the SerDes, SRIO interfaces correctly.
4. Slave must be powered on after master's boot.
For the master module, need to finish these processes:
1. Initialize the SRIO port and address space.
2. Set inbound SRIO windows covered slave's u-boot image stored in
master's NOR flash.
3. Master's u-boot image should be generated specifically by
make xxxx_SRIOBOOT_MASTER_config
4. Master must boot first, and then slave can be powered on.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Currently "u-boot", the elf file generated via u-boot-nand.lds does not
contain required debug information i.e. .debug_{line, info, abbrev, aranges,
ranges} into their respective _global_ sections.
The original ld script line arch/powerpc/cpu/mpc85xx/start.o
KEEP(*(.bootpg)) is not entirely correct because the start.o file is already
processed by the linker,therefore the file wildcard in "KEEP(*(.bootpg))" will
not process start.o again for bootpg.
So Fix u-boot-nand.lds to generate these debug information.
Signed-off-by: Anmol Paralkar <b07584@freescale.com>
Signed-off-by: John Russo <John.Russo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
NAND SPL code never compile the vector table.
So no need to setup interrupt vector table for NAND SPL.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After relocation of vector table in SDRAM's lower address, IVORs value should
be updated with new handler addresses.
As vector tables are relocated to 0x100,0x200... 0xf00 address in DDR.IVORs
are updated with 0x100, 0x200,....f00 hard-coded values.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For e500 and e500v2 architecturees processor IVPR address should be alinged on
64K boundary.
in start.S, CONFIG_SYS_MONITOR_BASE is stored blindly in IVPR assuming it to be
64K aligned. It may not be true always. If it is not aligned, IVPR + IVORs may
not point to an exception handler.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func. This also fixes the build errors:
ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marex@denx.de>
These calls should not be made directly any more, since bootstage
will call the show_boot_...() functions as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than the caller negating our progress numbers to indicate an
error has occurred, which seems hacky, add a function to indicate this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This seems to be unsigned char for no good reason. Tidy this up and
remove the casts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Add support for fixing usb mode and phy type for
MPH(Multi Port Host) USB controllers in device-tree nodes.
Required for socs like P3060, P5020, etc having MPH USB controller
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Some code cleanup done for USB device-tree fixup:
- handling error value returned from fdt_fixup_usb_mode_phy_type()
- using ARRAY_SIZE macro
- using snprintf instead of sprintf
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
fsl_lbc: add printout of LCRR and LBCR to local bus regs
sbc8548: Fix up local bus init to be frequency aware
sbc8548: enable support for hardware SPD errata workaround
sbc8548: relocate fixed ddr init code to ddr.c file
sbc8548: Make enabling SPD RAM configuration work
sbc8548: Fix LBC SDRAM initialization settings
sbc8548: enable ability to boot from alternate flash
sbc8548: relocate 64MB user flash to sane boundary
Revert "SBC8548: fix address mask to allow 64M flash"
MPC85xxCDS: Fix missing LCRR_DBYP bits for 66-133MHz LBC
eXMeritus HWW-1U-1A: Add support for the AT24C128N I2C EEPROM
eXMeritus HWW-1U-1A: Minor environment variable tweaks
It can be handy to have these in the output when trying to
debug odd behaviour.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
In the current u-boot code, the value of these fields are the reserved
value (0b100), through the signal integrity measurement on freescale's
board with these reserved setting, the signal eye is out of the recommended
spec for non-transition amplitude at 500mV nominal.
According to the errata for MPC8379E, we should make a change to the
recommended setting from essentially nothing at this time to 0b001 for SATA.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We already flush the kernel image after we've loaded it to ensure
visiblity to the other cores. We need to do the same thing for the
ramdisk and device tree images. In AMP boot scenarios we might not be
HW cache coherent with the secondary core that we are loading and
setting the ramdisk and device tree up for. Thus we need to ensure
we've flushed the regions of memory utilized by ramdisk and device tree
so the loadding and any modifications (from decompression or fdt updates)
are made visible to the secondary cores.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Standard Debian powerpc and powerpcspe systems only include hard-float
libgcc in their native compilers, which causes scary build warnings when
building U-Boot.
Debian and other PowerPC-supporting distributions used to provide libgcc
and other libraries in a "nof" (soft-float) form in the "multilib"
packages. As they were completely unused by the distribution and
therefore tended to be very buggy it was decided to save some time on
the part of the maintainers and build-servers by removing them.
Admittedly, right now the linker warnings do not indicate any problems,
as the included routines do not use any floating point at all.
The concern is that if floating-point code were ever added it might
cause hard-float code to be unexpectedly included in U-Boot without
generating a hard error. This would cause unexplained crashes or
indeterminate results at runtime.
The easiest way to resolve this is to borrow the routines that U-Boot
needs from the Linux kernel, which has the same issue.
Specifically, the routines are: _ashldi3(), _ashrdi3(), and _lshrdi3().
They were borrowed from arch/powerpc/kernel/misc_32.S as of v2.6.38-rc5,
commit 85e2efbb1db9a18d218006706d6e4fbeb0216213, and are GPLv2+.
The Makefile framework was copied from the U-Boot ARM port.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Fix:
cpu.c: In function 'checkcpu':
cpu.c:51:7: warning: variable 'ver' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This adds support for the Freescale COM Express P2020 board. This board
is similar to the P1_P2_RDB, but has some extra (as well as missing)
peripherals.
Unlike all other mpc85xx boards, it uses a watchdog timeout to reset.
Using the HRESET_REQ register does not work.
This board has no NOR flash, and can only be booted via SD or SPI. This
procedure is documented in Freescale Document Number AN3659 "Booting
from On-Chip ROM (eSDHC or eSPI)." Some alternative documentation is
provided in Freescale Document Number P2020RM "P2020 QorIQ Integrated
Processor Reference Manual" (section 4.5).
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
interactive.c: In function 'fsl_ddr_interactive':
interactive.c:1357:15: warning: variable 'len' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is useful for boards which cannot be reset in the usual way for the
85xx CPU. An example is a board which can only be reset by a hardware
watchdog.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The localbus controller node in the device tree is typically a root node,
even though the controller is part of CCSR. If we were to put the lbc
node under the SOC node, then the 'ranges' property in the lbc node would
translate through the 'ranges' property of the parent SOC node, and we
don't want that.
Since the lbc is a separate node, it's possible for the 'reg' property to
be wrong. This happened with the original version of p1022ds.dts, which
used a 32-bit value in the 'reg' address, instead of a 36-bit address.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Newer JEDEC DDR3 SPD Specifications define several additional values for
the DDR3 module_type field which were undefined when this code was
written. Update the code to handle the newer module types.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Several macros are used to identify and locate the microcode binary image
that U-boot needs to upload to the QE or Fman. Both the QE and the Fman
use the QE Firmware binary format to package their respective microcode data,
which is why the same macros are used for both. A given SOC will only have
a QE or an Fman, so this is safe.
Unfortunately, the current macro definition and usage has inconsistencies.
For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman
firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address
of NAND. There's no way to know by looking at a variable how it's supposed
to be used.
In the future, the code which uploads QE firmware and Fman firmware will
be merged.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the P1022/P1013, the work-around for erratum SATA_A001 was implemented
only if U-Boot initializes SATA, but SATA is not initialized by default. So
move the work-around to the CPU initialization function, so that it's always
executed on the SOCs that need it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA
controller, so it should be defined in config_mpc85xx.h instead of the various
board header files. So now CONFIG_FSL_SATA_V2 is always defined on the P1013,
P1022, P2041, P3041, P5010, and P5020. It was already defined for the
P1010 and P1014.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum A-003474: Internal DDR calibration circuit is not supported
Impact:
Experience shows no significant benefit to device operation with
auto-calibration enabled versus it disabled. To ensure consistent timing
results, Freescale recommends this feature be disabled in future customer
products. There should be no impact to parts that are already operating
in the field.
Workaround:
Prior to setting DDR_SDRAM_CFG[MEM_EN]=1, do the following:
1. Write a value of 0x0000_0015 to the register at offset
CCSRBAR + DDR OFFSET + 0xf30
2. Write a value of 0x2400_0000 to the register at offset
CCSRBAR + DDR OFFSET + 0xf54
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the fixup matchable with dts and kernel. Update the compatible from
"fsl,flexcan-v1.0" to "fsl,p1010-flexcan" and Change the "clock-freq"
property to "clock-frequency". We also change flexcan frequency from
CCB-clock to CCB-clock/2 according to P1010 spec.
We now keep the old interfaces to make previous kernel work. They should
be removed in the future.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum A-003999: Running Floating Point instructions requires special
initialization.
Impact:
Floating point arithmetic operations may result in an incorrect value.
Workaround:
Perform a read modify write to set bit 7 to a 1 in SPR 977 before
executing any floating point arithmetic operation. This bit can be set
when setting MSR[FP], and can be cleared when clearing MSR[FP].
Alternatively, the bit can be set once at boot time, and never cleared.
There will be no performance degradation due to setting this bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Configuring for sbc8349 board...
spd_sdram.c: In function 'spd_sdram':
spd_sdram.c:152:41: warning: variable 'trfc_high' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fix:
iop480_uart.c: In function 'serial_init':
iop480_uart.c:137:16: warning: variable 'val' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
40x_spd_sdram.c: In function 'spd_sdram':
40x_spd_sdram.c:137:6: warning: variable 'sdram0_b3cr' set but not used [-Wunused-but-set-variable]
40x_spd_sdram.c:136:6: warning: variable 'sdram0_b2cr' set but not used [-Wunused-but-set-variable]
40x_spd_sdram.c:129:6: warning: variable 'sdram0_ecccfg' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
44x_spd_ddr2.c: In function 'initdram':
44x_spd_ddr2.c:450:17: warning: variable 'dimm_spd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c: In function 'program_copt1':
44x_spd_ddr2.c:1003:16: warning: variable 'ddrtype' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c: In function 'DQS_calibration_process':
44x_spd_ddr2.c:2498:7: warning: variable 'window_found' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2497:16: warning: variable 'end_rffd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2496:16: warning: variable 'end_rqfd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2495:16: warning: variable 'begin_rffd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2494:16: warning: variable 'begin_rqfd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2493:7: warning: variable 'min_end' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
44x_spd_ddr.c: In function 'program_cfg0':
44x_spd_ddr.c:384:16: warning: variable 'dimm_64bit' set but not used [-Wunused-but-set-variable]
44x_spd_ddr.c:383:16: warning: variable 'dimm_32bit' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
cmd_ecctest.c: In function 'inject_ecc_error':
cmd_ecctest.c:116:6: warning: variable 'val' set but not used [-Wunused-but-set-variable]
cmd_ecctest.c: In function 'rewrite_ecc_parity':
cmd_ecctest.c:154:6: warning: variable 'val' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
4xx_ibm_ddr2_autocalib.c: In function 'get_membase':
4xx_ibm_ddr2_autocalib.c:157:8: warning: variable 'bxcf' set but not used [-Wunused-but-set-variable]
4xx_ibm_ddr2_autocalib.c: In function 'DQS_calibration_methodB':
4xx_ibm_ddr2_autocalib.c:722:8: warning: variable 'rffd' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
4xx_pcie.c: In function 'pcie_read_config':
4xx_pcie.c:230:6: warning: variable 'address' set but not used [-Wunused-but-set-variable]
4xx_pcie.c: In function 'pcie_write_config':
4xx_pcie.c:290:6: warning: variable 'address' set but not used [-Wunused-but-set-variable]
4xx_pcie.c: In function 'ppc4xx_setup_pcie_rootpoint':
4xx_pcie.c:1066:17: warning: variable 'rmbase' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
usb_ohci.c: In function 'dl_transfer_length':
usb_ohci.c:756:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
i2c.c: In function 'wait_for_bb':
i2c.c:81:16: warning: variable 'temp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
pci.c: In function 'pci_init_board':
pci.c:55:26: warning: variable 'pci_conf' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
* 'master' of git://git.denx.de/u-boot-video:
api: export LCD device to external apps
font: split font data from video_font.h
tools: logo: split bmp arrays from bmp_logo.h
lcd: add clear and draw bitmap declaration
VIDEO: mx3fb: GCC4.6 fix build warnings
Powerpc/DIU: Fixed the 800x600 and 1024x768 resolution bug
While video_font.h is useful even without referencing the font data, it
is not possible to be included multiple times because it defines font
data array right in the header.
This patch splits the font data array into video_font_data.h and so now
video_font.h can be included multiple times. This at least solves the
code duplication in board/mcc200/lcd.c.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Remove symbolic link generated by compiling. Fix makefile for out-of-tree
compiling error.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fix:
ctrl_regs.c: In function 'set_ddr_sdram_cfg_2':
ctrl_regs.c:641:15: warning: variable 'rcw_en' set but not used [-Wunused-but-set-variable]
ctrl_regs.c: In function 'compute_fsl_memctl_config_regs':
ctrl_regs.c:951:31: warning: array subscript is above array bounds [-Warray-bounds]
ctrl_regs.c:752:34: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
fsl_corenet_serdes.c: In function 'fsl_serdes_init':
fsl_corenet_serdes.c:511:8: warning: variable 'buf' set but not used [-Wunused-but-set-variable]
fsl_corenet_serdes.c:498:18: warning: variable 'lane_prtcl' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
options.c: In function 'populate_memctl_options':
options.c:486:28: warning: variable 'pdodt' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
fsl_lbc.c: In function 'upmconfig':
fsl_lbc.c:110:9: warning: variable 'mdr' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
tlb.c: In function 'disable_tlb':
tlb.c:175:34: warning: variable '_mas7' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
cpu_init.c: In function 'cpu_init_r':
cpu_init.c:320:7: warning: variable 'l2srbar' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wrong pointer was being used to copy code into L2SRAM.
Also removed the unreferenced variable l2srbar.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A few of the config registers changed definition between MMU v1.0 and
MMUv2.0. The new e6500 core from Freescale implements v2.0 of the
architecture.
Specifically, how we determine the size of TLB entries we support in the
variable size (or TLBCAM/TLB1) array is specified in a new register
(TLBnPS - TLB n Page size) instead of via TLBnCFG.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix USB device-fixup warning "node not found". This was occuring
because of static nature of start_offset variable
Static start_offset was storing offset of last node modified, and
was becoming issue if node fixup is carried multiple times,
resulting in "node not found" warning
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On some Freescale systems (e.g. those booted from the on-chip ROM), the
TLB that covers the boot page can also cover CCSR, which breaks the CCSR
relocation code. To fix this, we resize the boot page TLB so that it only
covers the 4KB boot page.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Verify that CCSR is actually located where it is supposed to be before
we relocate it. This is useful in detecting U-Boot configurations that
are broken (e.g. an incorrect value for CONFIG_SYS_CCSRBAR_DEFAULT).
If the current value is wrong, we enter an infinite loop, which is handy
for debuggers.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Calls to tlbwe and tlbsx should be preceded with an isync/msync pair.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some of the MAS register macros do not protect the parameter with
parentheses, which could cause wrong values if the parameter includes
operators.
Also fix the definition of TSIZE_TO_BYTES() so that it actually uses
the parameter. This hasn't caused any problems to date because the
parameter was always been 'tsize'.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.
Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
spi.c: In function 'spi_init_r':
spi.c:279:22: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
spi.c: In function 'spi_xfer':
spi.c:361:22: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
