- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
# Conflicts:
# arch/arm/mach-omap2/am33xx/Kconfig
U-Boot now supports parsing SPI NOR partitions from Device Tree. So enable
'mtd' command support for Espressobin board and define partition layout in
U-Boot Espressobin DTS file. Access to SPI NOR via 'sf' command is old
method and 'mtd' command is now preferred variant.
From include file remove '#define CONFIG_MTD_PARTITIONS' as this option is
now defined and enabled in defconfig file. This change is required to fix
compile error:
CC arch/arm/lib/asm-offsets.s
In file included from include/config.h:4,
from include/common.h:16,
from lib/asm-offsets.c:14:
include/configs/mvebu_armada-37xx.h:63: warning: "CONFIG_MTD_PARTITIONS" redefined
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
In file included from ././include/linux/kconfig.h:4,
from <command-line>:
include/generated/autoconf.h:44: note: this is the location of the previous definition
#define CONFIG_MTD_PARTITIONS 1
After enabling support for mtd command, output from 'mtd list' on
Espressobin board is:
=> mtd list
List of MTD devices:
* w25q32dw
- device: spi-flash@0
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/internal-regs/spi@10600/spi-flash@0
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000400000 : "w25q32dw"
- 0x000000000000-0x0000003f0000 : "firmware"
- 0x0000003f0000-0x000000400000 : "u-boot-env"
=>
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
As the logic here is only used when we have a USB host controller, test
on CONFIG_USB_HOST rather than CONFIG_USB in general. This lets us move
towards using CONFIG_USB only as a menu symbol to say that we have some
form of USB, and then USB_HOST or USB_GADGET depending on the role that
USB plays within the build.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reuse the common logic to allow for BOOT_TARGET_DEVICES to list USB as a
possibility if we're building for a platform that will have USB but not
if we don't, so that we don't hit the link-time check for trying to have
USB boot on a non-USB system.
Acked-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These USB defines do not change the build as there is no USB support
enabled currently.
Cc: Ian Ray <ian.ray@ge.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the variable used by PXE command for fdtoverlays support
since the commit 69076dff22 ("cmd: pxe: add support for FDT overlays").
Reused the unused "splashimage" address as CONFIG_SPLASH_SOURCE and
CONFIG_VIDEO_LOGO are not activated and U-Boot display the "BACKGROUND"
image found in extlinux.conf to manage splashscreen on stm32mp1 boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
By default bootmenu is loaded only from eMMC. After this change U-Boot
first tries to load bootmenu from uSD card and if it fails then fallback to
eMMC. People want to boot alternative OS from removable uSD without need to
modify eMMC content. So this backward compatible change allows it.
Part of this change is also optimization of trymmc* macros so they can be
used in preboot macro for loading bootmenu.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210618132704.32066-2-pali@kernel.org
Enable U-Boot bootz command and update env scripts to try loading also
zImage file and to try booting via bootz command.
Update also lowlevel_init.S code for checking validity of zImage magic to
correctly relocate kernel in zImage format.
This change allows U-Boot to directly boot Linux kernel without need for
converting kernel image into U-Boot uImage format.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210618132704.32066-1-pali@kernel.org
Swap out the TI-centric "envboot" logic for the generic distro_bootcmd
logic for the bootcmd we run before trying to do something more complex
involving additional firmware, etc.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210713141139.15183-1-trini@konsulko.com
The usbtty functionality is not currently used on these two platforms,
disable it.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210708014348.4010-1-trini@konsulko.com
Swap out the TI-centric "envboot" logic for the generic distro_bootcmd
logic for the bootcmd we run before trying to do something more complex
involving additional firmware, etc.
Cc: Lokesh Vutla <lokeshvutla@ti.com> (maintainer:J721E BOARD)
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701142743.26190-1-trini@konsulko.com
Remove the environment support for various legacy boot methods. With
this, we will now default to booting any distribution that follows the
generic distro boot framework and no longer attempt to boot various
legacy (to this SoC) scripts/etc. Note that if we do not find anything
here we will continue to try and Android methods and will start by
trying fastboot.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701132612.7559-3-trini@konsulko.com
This include file is only used by ti_omap5_common.h. Further, the move
is towards using the generic distro boot framework and not this set of
macros. Start by moving all of the contents in directly to where they
are used.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701132612.7559-2-trini@konsulko.com
Remove the environment support for various legacy boot methods. With
this, we will now default to booting any distribution that follows the
generic distro boot framework and no longer attempt to boot various
legacy (to this SoC) scripts/etc.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701132612.7559-1-trini@konsulko.com
Remove the environment support for various legacy boot methods. With
this, we will now default to booting any distribution that follows the
generic distro boot framework and no longer attempt to boot various
legacy (to this SoC) scripts/etc.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210610230147.22475-1-trini@konsulko.com
autoload: if set to "no" then rarpb, bootp or dhcp commands will
just perform a configuration lookup from the BOOTP / DHCP server,
but not try to load any image using TFTP
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210611161350.2141-8-Gireesh.Hiremath@in.bosch.com
The U-Boot "stemmy" board is mainly intended to simplify booting
mainline Linux on various smartphones from Samsung based on ST-Ericsson
Ux500. While the mainline kernel is working great, there are still some
features missing there. In particular, it is currently not possible to
charge the battery when using the mainline kernel.
This means that it is still necessary to boot the downstream/vendor
kernel from Samsung sometimes to charge the device. That kernel is
ancient, still uses board files + ATAGS instead of device trees and
relies on a strange very long kernel command line hardcoded in the
Samsung bootloader.
Actually, since mainline is booted with device trees there is a very
simple way to make the old downstream kernel work as well: We can
simply take most of the ATAGS passed to U-Boot from the Samsung
bootloader and copy them as-is when booting a kernel without device
tree. That way the long command line and other needed ATAGS are copied
as-is without having to bother with them.
The only exception is the ATAG_INITRD - since the initrd is loaded
by U-Boot, the atag for that should be generated in U-Boot so it points
to the correct address. All other ATAGS are copied as-is and not
generated in U-Boot.
Also use the chance and provide a serial# for U-Boot by parsing the
ATAG_SERIAL that is also passed by the Samsung bootloader.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
At the moment the "stemmy" board attempts to detect the RAM size with
a simple memory test (get_ram_size()). Unfortunately, this does not work
correctly for devices with 768 MiB RAM (e.g. Samsung Galaxy Ace 2
(GT-I8160), "codina"). Reading/writing memory after the 768 MiB RAM
succeeds but actually overwrites some earlier parts of the memory.
For U-Boot this does not result in any major problems, but on Linux
this will eventually lead to strange crashes because of the memory
corruption.
Since the "stemmy" U-Boot port is designed to be chainloaded from
the original Samsung bootloader, the most reliable way to get the
available amount of RAM is to look at the ATAGS passed by the Samsung
bootloader. Fortunately, the header used to generate ATAGS in U-Boot
(asm/setup.h) can also be easily used to parse them.
Also clarify and simplify stemmy.h a bit to make it more clear where
some of the magic values in there are actually coming from.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Enable support for the fec ethernet on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
On the Yocto image there is a single partition and the kernel
and dtb are present in the 'boot' directory.
Change it accordingly so that the board can boot the Yocto
image by default.
Use the generic 'load' command instead, which is able to
read from an ext4 partition.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Extend CONFIG_SYS_BAUDRATE_TABLE and include all standard baudrates and
also nonstandard up to the 6 MBaud. U-Boot's A3720 UART driver can use
baudrates from 300 Baud to 6 MBaud.
This changes all A3720 boards, since all of them include either
mvebu_armada-37xx.h or turris_mox.h config file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
While this platform has not yet been converted, there is active efforts
to do so. Keep the platform for now.
This reverts commit aa697e6904.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
also the last SPEAR3XX platform, remove that symbol as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Gerald Kerma <dreagle@doukki.net>
Cc: Tony Dinh <mibodhi@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Ajay Bhargav <contact@8051projects.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it.
This is also the last PL010_SERIAL using board, so remove those
references.
Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8315 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8568 platform, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and are
also missing conversion to CONFIG_DM. Remove them.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is all of the CONFIG_M548x platforms as well,
remove that code.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
Convert the CONFIG_SYS_I2C_LPC32XX configuration symbol from an include
directive to a Kconfig value.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic support for running U-Boot on the Embedded Artists LPC3250
Developer's Kit v2 board by launching U-Boot from the board's s1l loader
(which comes pre-installed on the board).
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
There's nothing special or unique to the lpc32xx that requires its own config
parameter for specifying the console uart index. Therefore instead of using
the lpc32xx-specific CONFIG_SYS_LPC32XX_UART include parameter, use the
already-available CONFIG_CONS_INDEX from Kconfig.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable EFI capsule update support. With the EFI capsule update,
you can update U-Boot, TF-A and OP-TEE. TF-A and OP-TEE are
usually combined as a FIP binary, but if the binary is bigger
than 480KB, you have to modify FIP header, split the OP-TEE
and stores the OP-TEE binary in the different place. This
configuration supports both cases.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.
For more information, see this page;
https://www.96boards.org/product/developerbox/
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add initial support for the PCB description EEPROM for SiFive HiFive
Unmatched boards.
This implementation is refactored based on Paul Walmsley's porting and
adopt the suggestions from David Abdurachmanov.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This patch adds openpiton-riscv64 SOC support. In particular, this
board supports a standard bootflow through zsbl->u-boot SPL->
opensbi->u-boot proper->Linux. There are separate defconfigs for
building u-boot SPL and u-boot proper
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Set default fdtfile names for unleashed and unmatched boards, as used
in the upstream Linux kernel. This allows sysboot command to find and
load appropriate dtb for the matching kernel from universal stock
Ubuntu RISC-V rootfs images based on fdtdir setting in extlinux.conf.
Signed-off-by: Dimitri John Ledkov <dimitri.ledkov@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
cc: Paul Walmsley <paul.walmsley@sifive.com>
cc: Palmer Dabbelt <palmer@dabbelt.com>
cc: Anup Patel <anup.patel@wdc.com>
cc: Atish Patra <atish.patra@wdc.com>
cc: Pragnesh Patel <pragnesh.patel@sifive.com>
cc: Green Wan <green.wan@sifive.com>
Init GICv3 for V3U Falcon in early phase
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add board code for the R8A779A0 V3U Falcon board.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - various small rebase fixes and clean ups
Based on the comment in socfpga_soc64_common.h, the intention is for
CONFIG_SYS_MEM_RESERVE_SECURE to be unused. However, in the code we do:
...
and that will evaluate to true. This leads to unwanted code being
compiled. Further, as CONFIG_SYS_MEM_RESERVE_SECURE has not been
migrated to Kconfig, this leads to a mismatch in the size of gd
depending on if we have or have not also had <configs/BOARD.h> also
included yet.
Remove the define as it's not needed.
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Chee Hong Ang <chee.hong.ang@intel.com>
Cc: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
RK3568 is a high-performance and low power quad-core application
processor designed for personal mobile internet device and AIoT
equipments.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
fdtoverlay (pxe_utils) require define fdtoverlay_addr_r env variable
for example sunxi-common.h meson64.h already have it.
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDLD78cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLhSB/0UqOd+Ujf2meiHU9yr
oOOCLxVTjTUfIZKLad/zwlj2Xqzsjs6XMawC95BgouvkQLmj/gwerRWcZPg9l7/X
hvb9VJi+iJoLRRpBPbeF3bMb92kCE+YZodFXyutlcY+Z0ZB9755zoVgR6ccKfksd
Xp2y8AFptfYQNZ1l0yb3lhm1261CldWALrGTjRpY2hQ8nEMbV8z6WUB1hAF9CECa
PGbKaiqm9OdktwHsLy4cYFFCuzkykn6T3P6ODineP7IxgEgZKTfJClSTFGY9S0GQ
kwd7K/7j0W3rI5NPknB+Fb4IFAaTs/oozR+5ml7j+2S3G5GXjSGx8zaSOmOZvpP3
KxwN
=/I5V
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for the 2021.10 cycle:
This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs
connected to MAC1 and MAC2. The second Aquantia PHY is located at a
different address on the MDIO bus compared to rev C (0x8 instead of 0x1).
Fix-up the Linux device tree to update the PHY address for the second
Aquantia PHY on boards revisions D and up. Also rename the PHY node to
reflect the changes.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
A system clock of 66MHz was chosen for the pg-wcom-ls102xa.
Compared to the Evalboard, this corresponds to a reduction of 1/3.
The system counter clock should have been reduced accordingly,
but that was not the case, so we had a system time that was
1/3 behind the real time.
This patch corrects the system counter clock to
8.333MHz = 66.667MHz / 8.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to improve power consumption ls102x allows to disable peripherals
that are not in use.
This patch follows SELI8 HW design description and disables peripherals
that are not in use in our designs, the same configuration is applicable
and for EXPU1.
This patch uses available hwconfig option for updating ls102x device
disable configuration.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The default behavior in the latest u-boot revisions is to rotate the
active net device to the next available if the requested link is not
established.
For our ls102x based devices this would mean that if active debug net
device is not available, u-boot will rotate and set the next net device
that is one of the estar adapters.
To return from this situation manual action to set correct ethact
adapter will be needed and this can be annoying when working in
debug mode.
Setting ethrotate=no will disable net adapter rotation and will make sure
that the primary adapter is always used.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In our designs we reserve PRAM area at the end of the RAM, and in order
this area to be visible and taken into account by the u-boot memory mgmt
CONFIG_PRAM has to be defined.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
From production view this is standard test executed during production on
all linux based foxmc cards.
On CENT2 HW defined memory region is zero means that some DDR accesses are
done by memory_post_dataline and memory_post_addrline but pattern tests
are skipped that's why mem_regions is fast there.
On ls102x for the complete DDR region of 1GiB memory_regions_post_test
takes approx. 4min and this is too much for production, so this patch
defines only 1MiB region as compromise.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
is used instead.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Michael Walle <michael@walle.cc> [for kontron-sl28]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards, according to the schematic and per the board I own, use an
M24256-BWDW6TP I2C EEPROM which requires two address bytes.
This fixes the 'mac' command which is used to program, among other
things, the MAC addresses for the ethernet interfaces on the board.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports Falcon boot support for Microchip SAMA5D3 Xplained,
tested on raw MMC, and on raw NAND.
spl_start_uboot() is has the simplest possible implementation.
It doesn't test the environment because enabling environment support
currently causes the SPL to exceed its maximum size (64 KiB).
It doesn't check the serial for incoming characters either because
this functionality currently doesn't seem to work from the SPL
on this board.
Settings for Falcon boot from at FAT partition are also added to
avoid compile failures when CONFIG_SPL_OS_BOOT is enabled, but this
particular case is currently not functional as adding FAT and
partition support cause the SPL to be too big again.
Signed-off-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Add default fdtfile environment variable with value
marvell/armada-3720-turris-mox.dtb.
This can be useful for some boot scenarios.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable config options required to add support for USB Mass storage boot,
USB DFU boot, host and device modes in U-Boot.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-11-a-govindraju@ti.com
For USB DFU boot mode there is a limitation on the load address of boot
images that they have to be less than 0x70001000. Therefore, move the
SPL_TEXT_BASE address to 0x70000000.
Currently ATF is being loaded at 0x70000000, if the SPL is being loaded at
0x70000000 then ATF would overwrite SPL image when loaded. Therefore, move
the location of ATF to a latter location in SRAM, past the SPL image. Also
rearrange the EEPROM and BSS data on top of ATF.
Given below is the placement of various data sections in SRAM
┌──────────────────────────────────────┐0x70000000
│ │
│ │
│ │
│ SPL IMAGE (Max size 1.5 MB) │
│ │
│ │
│ │
├──────────────────────────────────────┤0x7017FFFF
│ │
│ SPL STACK │
│ │
├──────────────────────────────────────┤0x70192727
│ GLOBAL DATA(216 B) │
├──────────────────────────────────────┤0x701927FF
│ │
│ INITIAL HEAP (32 KB) │
│ │
├──────────────────────────────────────┤0x7019A7FF
│ │
│ BSS (20 KB) │
├──────────────────────────────────────┤0x7019F7FF
│ EEPROM DATA (2 KB) │
├──────────────────────────────────────┤0x7019FFFF
│ │
│ │
│ ATF (123 KB) │
│ │
│ │
├──────────────────────────────────────┤0x701BEBFB
│ BOOT PARAMETER INDEX TABLE (5124 B)│
├──────────────────────────────────────┤0x701BFFFF
│ │
│SYSFW FIREWALLED DUE TO A BUG (128 KB)│
│ │
├──────────────────────────────────────┤0x701DFFFF
│ │
│ DMSC CODE AREA (128 KB) │
│ │
└──────────────────────────────────────┘0x701FFFFF
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-9-a-govindraju@ti.com
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Supported boot device types in iMX8MN: MMC, DHCP.
Add DISTRO_DEFAULTS config option and include the distro boot command
header file to enable full support of distro boot on i.MX8M Nano EVK (both
DDR and LPDDR derivatives).
Drop previous environment, which was targeting customized boot commands and
boot order.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.
Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.
Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
Uncompressed aarch64 kernel Image are rather large, increase the bootm
size limit to 64 MiB to cater for that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Currently the config options CONFIG_SYS_DFU_DATA_BUF_SIZE and
CONFIG_SYS_DFU_MAX_FILE_SIZE are being set in include/configs/<board>.h
files and also in <board_name>_defconfig files without a Kconfig option. It
is easier for users to set these configs in defconfig files than in config
header files as they are a part of the source code.
Add Kconfig symbols, and update the defconfigs by using tools/moveconfig.py
script.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
TFTP transfer size can be used to re-size the TFTP progress bar on
single line based on the server reported file size. The support for
this has been around from 2019, but it was never converted to proper
Kconfig.
While adding this new Kconfig, enable it by default for OMAP2+ and K3
devices also.
Signed-off-by: Tero Kristo <kristo@kernel.org>
Make it possible to invoke rescue boot from U-Boot console, without
having to press the factory reset button. This is needed when accessing
the device remotely, for example.
Achieve this by putting rescue command into `bootcmd_rescue` default
environment variable and setting some distroboot environment variables
to their default values when the factory button is pressed.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Remove qemu_mips boards because DM migration doesn't make sense.
The board support for qemu_mips is already marked as deprecated
in Qemu in favour of the Malta board. Also qemu_mips support
has been removed from Linux a long time ago.
The official replacement is the Malta board. The same Malta U-Boot
image can be used with Qemu and on physical hardware.
All combinations of Big Endian and Little Endian as well as 32 bit
and 64 bit are supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Increase the BOOTM_LEN to 32M . This would allow a bigger kernel image to be
booted, for example the multi_v7_defconfig.
Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
resetting ...
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We just need to initialize all the clocks pre-reloc. The clock driver
creates a bunch of devices, so we need to increase the pre-reloc malloc
arena.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Enable CONFIG_DM_ETH in configs/pm9263_defconfig
Drop legacy initialization in board/ronetix/pm9263.c
Remove network related setting from include/configs/pm9263.h
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Now that single defconfig can be used for booting AM64 EVM and SK,
default device tree will not work for selecting dtb for kernel.
Update the env to select right dtb based on eeprom.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Current BSS allocation of SPL is as below:
size spl/u-boot-spl
text data bss dec hex filename
144572 5484 1752 151808 25100 spl/u-boot-spl
But 20KB is allocated currently for BSS. Reduce it to 4KB and
save some space for stack.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Prevent shell access on boot failure by entering an infinite
loop.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Minor cosmetic changes to unify `CONFIG_EXTRA_ENV_SETTINGS'
indentation between Bx50v3 and PPD to make comparison and
review easier and simplify the default boot command.
Signed-off-by: Ian Ray Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Enable EFI capsule update features to be enabled by default also with all
dfu valid options for ZynqMP.
This feature was tested on Xilinx ZynqMP zcu104 board with defining
dfu_alt_info="mmc 0:1=boot.bin fat 0 1;u-boot.itb fat 0 1"
and
dfu_alt_info="sf 0:0=boot.bin raw 0 0x50000;u-boot.itb raw 0x80000
0x500000".
There is a need to increase malloc size for getting dfu mmc to work.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
-----BEGIN PGP SIGNATURE-----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=JwRN
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2021-04-24' of https://source.denx.de/u-boot/custodians/u-boot-mips
- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
Add support for usb dfu & thor to distro boot on zynq platform.
Add 60s timeout of dfu-utils to start transaction. Remove
DFU_ALT_INFO_RAM as we use bootcmd_usb_dfu instead of dfu_ram.
Remove DFU_ALT_INFO_MMC as part of distro boot cleanup.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change "dfu_usb" to "usb_dfu" for better representation and change
required macros. Add 60s timeout of dfu-utils to start transaction.
Add support for usb thor to distro boot. Remove DFU_ALT_INFO_RAM
as we use bootcmd_usb_dfu instead of dfu_ram.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dfu ram info is wired in connection to Linux kernel and certain setup.
We should change this to be more generic as others command. That's why
using boot via script is the way to go.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In usb boot mode distro boot should select usb device as primary boot
device instead of usb host. So make usb dfu as primary boot device. But do
not list it in boot_targets as fallback option because it is not classic
mode for booting. Using 60s timeout by default should be enough time for
dfu-utils to start transaction. In case none needs this please change
timeout value in the command or disable CONFIG_DFU_TIMEOUT.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
So far we were defining a somewhat confusing PHYS_SDRAM_1_SIZE variable,
which originally was only used for setting the memtest boundaries. This
definition in highbank.h has been removed about a year ago (moved to
Kconfig), so we also don't need the hard-coded size definition any longer.
Get rid of the misleading memory size definition, which was actually wrong
anyway (it's 4088 MB for those machines with just 4GB of DRAM).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
All Calxeda machines are actually a poster book example of device tree
usage: the DT is loaded from flash by the management processor into
DRAM, the memory node is populated with the detected DRAM size and this
DT is then handed over to the kernel.
So it's a shame that U-Boot didn't participate in this chain, but
fortunately this is easy to fix:
Define CONFIG_OF_CONTROL and CONFIG_OF_BOARD, and provide a trivial
function to tell U-Boot about the (fixed) location of the DTB in DRAM.
Then enable DM_SERIAL, to let the PL011 driver pick up the UART platform
data from the DT. Also define AHCI, to bring this driver into the driver
model world as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far on Highbank/Midway machines U-Boot only ever uses 512MB of DRAM,
even though the machines have typically 4GB and 8GB, respectively.
That means that so far we didn't need an extra limit for placing the DTB
and initrd, as the 512MB are lower than the kernel's limit ("lowmem",
typically 768MB).
With U-Boot now needing to learn about the actual memory size (to
correctly populate the EFI memory map), it might relocate fdt and initrd
to the end of DRAM, which is out of reach of the kernel.
So add limiting values to the fdt_high and initrd_high environment
variables, to prevent U-Boot from using too high addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_SUPPORT_RAW_INITRD out of the octeontx_common header
and into the defconfig files.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a patchset which makes away with the .bind() controller indexing
workaround which was broken since before v2021.04, and then adds PHY
support and MX8M support on top of that. Better add it into the release
early to get as much testing as possible done, because this really does
a lot of changes to the ehci-mx6 driver.
Enable USB host support on MX8MM Verdin.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The "booti" command to load arm64 Linux kernels supports automatic
decompression of zipped kernel images, but relies on some environment
variables to point to usable buffer RAM.
Add those variables and let them point to some default values, that
should cover most use-cases.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit 69076dff22 ("cmd: pxe: add support for FDT overlays") added
support for loading DT overlay files to PXE boot. However, it needs
additional environment variable which points to memory location which
can be used to temporary store overlay data.
Add it and in the process unify alignment using spaces and fix comment.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However, this call is missing for ls1012a boards. As a result EFI
boot doesn’t work. Fix this issue by removing custom definition of
scan_dev_for_boot and use the default definition instead.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With all preparations in place, switch over to DM_SERIAL.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The DSA sandbox driver is used for unit testing the DSA class code.
It implements a simple 2 port switch plus 1 CPU port, and uses a
very simple tag to identify the ports.
The DSA sandbox device is connected via CPU port to a regular Ethernet
sandbox device, called 'dsa-test-eth, managed by the existing eth
sandbox driver. The 'dsa-test-eth' is not intended for testing the
eth class code however, but it is used to emulate traffic through the
'lan0' and 'lan1' front pannel switch ports. To achieve this the dsa
sandbox driver registers a tx handler for the 'dsa-test-eth' device.
The switch ports, labeled as 'lan0' and 'lan1', are also registered
as eth devices by the dsa class code this time. So pinging through
these switch ports is as easy as:
=> setenv ethact lan0
=> ping 1.2.3.5
Unit tests for the dsa class code were also added. The 'dsa_probe'
test exercises most API functions from dsa.h. The 'dsa' unit test
simply exercises ARP/ICMP traffic through the two switch ports,
including tag injection and extraction, with the help of the dsa
sandbox driver.
I took care to minimize the impact on the existing eth unit tests,
though some adjustments needed to be made with the addition of
extra eth interfaces used by the dsa unit tests. The additional eth
interfaces also require MAC addresses, these have been added to the
sandbox default environment.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20210216224804.3355044-5-olteanv@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.
It is based on NXP LS1021 SoC and it provides following interfaces:
- IFC interface for NOR, NAND and external FPGA's
- 1 x RGMII ETH for debug purposes
- 2 x SGMII ETH for management communication via back-plane
- 1 x uQE HDLC for management communication via back-plane
- 1 x I2C for peripheral devices
- 1 x SPI for peripheral devices
- 1 x UART for debug logging
It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It's an old bringup board with out upstream Linux or L4T support
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Add power_max77696_init() function.
Since warp doesn't support DM, the keeping its code in board file is
better than maintainig the file of driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. It is also the only ARCH_T2081 board so remove that support
as well.
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <linuxfae@technexion.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Thomas Weber <weber@corscience.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM by the deadline.
Remove them.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Erik van Luijk <evanluijk@interact.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The mvsata_ide driver was due for DM conversion by v2019.07. As that
has long passed, remove the driver and disable it in the boards which
had enabled it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. In order to
convert to using the DWC SATA driver under DM further migrations are
required.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
-----BEGIN PGP SIGNATURE-----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=4VxR
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210409' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
A now removed comment promises to "limit SYSRAM usage to first 128 KB".
This would imply that only SYSRAM from 0x2ffc0000 - 0x2ffe0000 would be
used. This is not what happens at all.
First, SPL_MAX_SIZE is referenced from SPL_TEXT_BASE, which on all
existing configs is set to 0x2ffc2500, not SYSRAM_BASE (0x2ffc0000).
Some of it is in the first 128 KiB and some of it is in the second
128 KiB chunk of SYSRAM.
Second, SPL_MAX_SIZE, does not restrict the BSS size. While a valiant
attempt is made via SPL_BSS_MAX_SIZE, the value of 0x00100000 is much
larger than SYSRAM, and doesn't account for the non-BSS sections.
Because we're putting the .text and .bss in the same boat, the correct
way to limit them together is via SPL_MAX_FOOTPRINT. With the current
SPL_TEXT_BASE, we couldn't limit even a very basic SPL to the first
128 KiB, and there is no technical reason to do so. Because of this,
simply allow the SPL to use all SYSRAM.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
CONFIG_SPL_BSS_START_ADDR is only used on a few mach- linker scripts.
stm32mp1 uses the generic script under arch/arm/cpu/u-boot-spl.lds,
which does not make use of this definition.
The SPL BSS starts in SRAM, right after .text, .rodata, .data, and
.u_boot_list. A very short version of the STM32MP1 memory map is:
* SYSRAM: 2ffc0000 - 30000000 <- all of SPL is here
* DRAM: c0000000+
0xC0200000 is a DRAM address, and has nothing to do with SPL. It is
just very misleading to have it next to CONFIG_SPL_BSS_MAX_SIZE, or to
have it at all.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for
loading images"), FIT images must be malloc()'d before being loaded.
The old size of 1 MiB is suitable for FIT images with u-boot and an
FDT, but something containing a linux kernel is almost sure to fail.
It's safe to extend malloc all the way to 0xc2000000, but no further.
Linux likes to be loaded at 0xc2000000, so we use that as our cutoff
point. This gives us 29 MiB of malloc() space, which suited for more
complex FIT images including several DTBs, kernel, and OP-TEE images.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
All these files are add for support rt-thread art-pi board
- add board/st/stm32h750-art-pi, defconfig, header support for u-boot
for more information about art-pi, please goto:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enabled "fsl,legacy-bch-geometry" in U-Boot device tree overlay
to match the legacy BCH geometry layout, which mainline Linux
applies when "fsl,use-minimum-ecc" is not specified in the device
tree.
Reinstated SYS_NAND_ONFI_DETECTION, which when disabled, masked
the mismatch on SOMs with Winbond NAND flash chips.
Signed-off-by: Niel Fourie <lusus@denx.de>
Convert the UDOO board to use DM_ETH.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block, DM MMC and DM SATA support on iMX6 Udoo
convert board code to match the DM support.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since Toradex provides the full set of overlays for Linux kernel
for display interfaces for both Apalis iMX6Q and Colibri iMX6DL
modules, the video= settings are obsolete. Remove them.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
All the other boards have tdxargs specified for setting manual kernel
command-line arguments. Add them also to NAND-based boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for loading images")'
changed the way buffer allocation worked for SPL to a more flexible
method.
For venice this caused breakage that is resolved by increasing the size
of CONFIG_SYS_SPL_MALLOC_SIZE as the current FIT slighly exceeds 512KiB.
Additionally remove the unnecessary comment on CONFIG_SPL_BSS_MAX_SIZE
and CONFIG_SYS_SPL_MALLOC_SIZE as the size is obvious from the define.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model for MTD and NAND support allowing us to remove
the iomux, init, and most of the static configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable dm support for USB (which also requires dm support for fixed
regulators used for vbus enable) and remove usb iomux which is no
longer needed.
We can remove the handling of otgpwr_en gpio as this is defined in
dt as usbotg vbus-supply but we need to keep the handling of
USB_HUB_RST# for boards that have a USB HUB as that isn't defined in
the dt's currently.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
In preparation to add SiFive Unmatched board support, let's rename
the existing fu540 board to unleashed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This define was left over from a previous revision, and was never used.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This will be replaced with the driver model version
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Stefan Roese <sr@denx.de>
CC: Tom Rini <trini@konsulko.com>
Unfortunately this board has no DM support at all. We are also way past
the deadline for driver model support for various devices on this board.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Stefan Roese <sr@denx.de>
These boards use an MMC driver that does not use this definition
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Stefan Roese <sr@denx.de>
CC: Mario Six <mario.six@gdsys.cc>
CC: Dennis Gilmore <dgilmore@redhat.com>
Call 'run update_uboot' to fetch u-boot-spl.kwb via TFTP and write it
into the correct SPI flash location. The latter's size is defined in
DS414's DTB file, so hard-coding it should be acceptable here.
Take care to not append garbage from RAM to the written image and to
stay within assigned flash boundaries even if an oversized image was
fetched.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Move the relevant bits from ds109.{c,h} into common/ and adjust the code
to fit both DS109 and DS414. Moreover:
* Introduce syno_board_id() which translates CONFIG_MACH_TYPE into the
expected board ID tag value.
* Properly initialize isusbhost, mac and mtu fields from env variables.
* Set the right bootargs/bootcmd to correctly boot legacy kernel out of
the (DS414) box. Getting the ramdisk location right is a bit tedious.
Cc: Walter Schweizer <swwa@users.sourceforge.net>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBr+AgRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebnqQf/dZUk4cpj4q29icFJhAhG3wUkzKdKywWu
wOwHPIaUIetytpjwKTbkv0cUdel5Jhp9mvnJ2O5cRUZlVdgCH+lEQmFiq1O74Jf5
IwYBN74xZuP7+rno3ZxuKhjj2ixbpeg2A5R/o7gaevIgtu4vCK71qrj3y+unjnnt
Rd5BGaVzouMya0lS9cdkrzE1vmuLXs7ZJBvKdppaNda0VScJj+JP3NqooFKRKPU+
OeyblmtfL5lGOXFdY7Wfjg0pzv5L8fJxDaYDxf6iRWWG/X6RO6zV26MWAo28Ga+J
E3fuvl0mBqr1eAg3Cf17j4s9gRZv1tMtS6Mol1scIcBrldalVFA44g==
=x75X
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm
ENOSYS clean-up
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
Currently it is not possible to boot Linux from the SD card
by default.
Make the necessary adjustments to allow it.
Reported-by: Peter Bergin <peter@berginkonsult.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrey Zhizhikin <andrey.z@gmail.com> # imx8mn_ddr4_evk
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Drop a irrelevent comment now the related configs have moved
to the various config files.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mimicing for example the rk3399, set the SYS_BOOTM_LEN to 64MB so
that regular kernel images can get loaded without problems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SYS_LOAD_ADDR currently is at 0x00280000 which is only 512KB
behind the area where we load u-boot to, which depending on u-boot size
may overlap at some point.
So for safety just pick the same value rk3399 has and set
CONFIG_SYS_LOAD_ADDR to 0x00800800 on rk3368 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
At present the eMMC device does not have an alias so it appears after
the SD card which is device 1. There is no device 0 which is odd.
Make the eMMC device be the first one. Update the boot script to use the
new device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
LS1028A-QDS has CONFIG_SPI_FLASH_SST and CONFIG_SPI_FLASH_EON defines
present in header. Move these entries from header to defconfigs.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is now safe to remove Flexspi configs NXP_FSPI_FLASH_SIZE and
NXP_FSPI_FLASH_NUM options from headers as they are no longer used by
driver anymore.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
More than one pumpkin board has been made with different MediaTek SoCs.
Rename the pumpkin board to follow the naming convention of all
other MediaTek boards and also to not be confusing when other pumpkin
boards will be added in follow-up commits.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).
This patch adds the required board support to boot Si-Linux EK874 board
based on R8A774C0 SoC.
DTS files apart from r8a774c0-ek874-u-boot.dts and r8a774c0-u-boot.dtsi
have been imported from Linux kernel 5.11 commit f40ddce88593
("Linux 5.11").
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
The HiHope RZ/G2M board from HopeRun consists of main board
(HopeRun HiHope RZ/G2M main board) and sub board(HopeRun
HiHope RZ/G2M sub board). The HiHope RZ/G2M sub board sits
below the HiHope RZ/G2M main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2M board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
-----BEGIN PGP SIGNATURE-----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=nIJc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210312' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Add WATCHDOG_RESET() in MTD framework and STM32 QSPI driver
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
Current BSS allocation of SPL is as below:
$ size spl/u-boot-spl
text data bss dec hex filename
132369 7852 1496 141717 22995 spl/u-boot-spl
But 20KB is allocated currently for BSS. Reduce it to 3KB and save some
space for stack.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In a previous attempt to unify config options and remove items
from the whitelist file, SPL items were moved into a section
enabled with CONFIG_SPL_BUILD. Unfortunately, SPL_PAD_TO
is referenced at the head Makefile and uses this define
to create padding of the output file. When it was moved
to CONFIG_SPL_BUILD, it caused boot errors with devices
that are not booting from NOR. Fix the boot issues by moving
SPL_PAD_TO out so it's always.
Fixes: 7bb33e4684 ("ARM: da850-evm: Unify config options with Kconfig")
Signed-off-by: Adam Ford <aford173@gmail.com>
The STM32MP15 boards have no reason to configure bootdelay in stm32mp1.h
as it is already done with CONFIG_BOOTDELAY (default = 2) and in
include/env_default.h.
This patch allows configuration for customers which reuse stm32mp1.h
and reduce the size of the default environment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add target to Makefile to generate "u-boot-spl-dtb.hex" for Intel
SOCFPGA SOC64 devices (Stratix 10 and Agilex). "u-boot-spl-dtb.hex"
is hex formatted spl with and offset of CONFIG_SPL_TEXT_BASE. It
combines the spl image and dtb. "u-boot-spl-dtb.hex" is needed to
generate the final configuration bitstream for Intel SOCFPGA SOC64
devices.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
CONFIG_BOOTCOMMAND have been moved to Kconfig.boot. This patch
move the CONFIG_BOOTCOMMAND macro from socfpga_soc64_common.h to
*_defconfig file for both Stratix 10 and Agilex.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Now that we have switched to CONFIG_OF_CONTROL, and we can use the
env variable 'fdtcontroladdr' directly instead of creating one that
is duplicated.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The QEMU ppce500 target integrates a Freescale I2C controller and
has a Pericom pt7c4338 RTC connected to it. Enable corresponding
DM drivers so that 'date' command is actually useful.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present the board supports non-DM version PCI and E1000 drivers.
Switch over to use DM ETH and PCI by:
- Rewrite the PCI address map functions using DM APIs
- Enable CONFIG_MISC_INIT_R to do the PCI initialization and
address map
- Drop unnecessary ad-hoc config macros
- Remove board_eth_init() in the board codes
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The QEMU ppce500 target integrates 2 NS16550 serial ports. Switch
over to use the DM version of the driver by:
- drop unnecessary ad-hoc config macros
- add get_serial_clock() in the board codes
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_SYS_PCI_MAP_END currently points to 0xe8000000, which means
the upper end of the virtual address mapped to PCI bus address ends
at 0xe8000000. But this is wrong as the CCSBAR was already mapped
at 0xe0000000 with a 1 MiB size.
Fixes: fa08d39517 ("PPC 85xx: Add qemu-ppce500 machine")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds support for more PMBus compatible devices to the NXP
drivers for its QorIQ family devices. At runtime, the voltage regulator is
queried over I2C, and the required voltage multiplier determined. This
change supports the DIRECT and LINEAR PMBus voltage reporting modes.
Previously, the driver only supported a few specific devices such as the
IR36021 and LTC3882, so this change allows the QorIQ series to be used
with a much larger variety of core voltage regulator devices.
checkpatch warning "Use if (IS_DEFINED (...))" was ignored to maintain
consistency with the existing code.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_VIDEO migration deadline is already expired, but around
80 Allwinner boards are still using video in a legacy way:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Convert the legacy video driver over to the DM_VIDEO framework. This is
a minimal conversion: it doesn't use the DT for finding its resources,
nor does it use DM clocks or DM devices for the outputs (LCD, HDMI, CVBS).
Tested in Bananapi M1+ Plus 1920x1200 HDMI out. (Jagan)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: rebase and smaller fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now when usbtty serial console is fixed in U-Boot enable CONFIG_USB_TTY for
Nokia RX-51 board by default.
Fix also USB product id as U-Boot ignores CONFIG_USBD_PRODUCTID macro and
include U-Boot string into USB product name to indicate usage of U-Boot.
CONFIG_CONSOLE_MUX is already used and U-Boot console is available for
all in/out devices. Therefore there is no need to have separate commands
'run sercon', 'run usbcon' and 'run vgacon', so remove them.
As space for U-Boot is limited to 256kB, enable CONFIG_OPTIMIZE_INLINING
and disable some other unused options so CONFIG_USB_TTY can be enabled.
Nokia RX-51 does not have easily accessible UART serial console so the only
option for easy debugging is to use device's keyboard+screen or this usbtty
serial console over USB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
There is a second lpddr configuration with 2GB of RAM, but this requires
different RAM timings, so in addition to adding the timing file, a
separate defconfig is necessary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Make the conversion to driver model as it is mandatory.
Tested booting the Linux kernel from the SD card.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Remove the SATA support for now as the i.MX53 support has not
been added yet.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The RGMII link delays can be set on either MAC or PHY side. Set the
rgmii-id PHY mode for FEC and remove FEC_ENET_ENABLE_.XC_DELAY
setting, so that these definitions aren't used anymore throughout
the U-Boot.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Both NXP SoCs i.MX8 and i.MX8X have ENET gigabit MAC.
Define FEC_QUIRK_ENET_MAC for the imx8 platform and remove this
definition from configs of boards, based on MX8/MX8X.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Some root filesystem configurations do not have separate /boot partition,
but rather place kernel, DT, scripts into /boot directory. Search the /boot
directory for these boot components in case they are not found in /, which
is the old behavior.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Replace filesystem specific fatload command with a filesystem agnostic
load command, so the board can boot from e.g. ext4 too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There is now CONFIG_SPL_DM_SPI{,_FLASH}, however keeping
CONFIG_DM_SPI{,_FLASH} enabled in SPL seems to grow the SPL
by a couple of bytes:
text data bss dec hex filename
- 34069 1568 96 35733 8b95 spl/u-boot-spl
+ 34075 1568 96 35739 8b9b spl/u-boot-spl
In either case, the binary is bootable, so remove the part
in board config.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
This reverts commit 03a673cf49 ("dh_imx6: Switch to full DM-aware").
According to discussion [1], the patch is known to break the dh_imx6
board, however it made it upstream just before 2021.01-rc4, likely by
mistake. Revert this patch to put the board back into working order.
Also note that this board has no DM SPL support due to OCRAM size
limitations, but that is fine, as SPL DM support is optional.
[1] https://lists.denx.de/pipermail/u-boot/2020-June/417986.html
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Add support for booting from USB pen drive, since USB host port is
available on the STM32MP1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is the last ARCH_MPC8569 board, remove that support
as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Convert the hikey to use DM_USB and DM_ETH.
Conversion based on rpi as it has a similar DWC config.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Drop CONFIG_DM_I2C undefs from board header files, and make them
disabled on these boards in defconfigs instead.
Disabling on Kconfig symbol was done automatically with this script:
cd configs
files=(*ls1046a*)
files2=(*T104*RDB*)
files3=(ls1021atwr_*)
files4=("imx8mp_evk_defconfig phycore-imx8mp_defconfig")
combine=("${files[@]}" "${files2[@]}" "${files3[@]}" "${files4[@]}")
cd ..
for item in ${combine[*]}
do
echo "Adjusting $item"
echo "# CONFIG_SPL_DM_I2C is not set" >> configs/$item
make $item && make savedefconfig && cp defconfig configs/$item
done
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
OF_STDOUT_PATH was meant to hold the devicetree path to the serial
console, to be put into the linux,stdout-path property of the chosen node.
The only user of that was sunxi, and it was actually wrong for years
there: the paths hardcoded in sunxi_common.h were not matching the DTs,
evident by the leading 0's in nodenames, which have been removed years
ago.
On top of that, "linux,stdout-path" is now deprecated for a while (Linux
commit 2a9d832cc9aae from November 2014), and also all modern DTs
(including those included in U-Boot) carry a "stdout-path" property
already.
So remove the stanza from sunxi_common.h, and, since this was the last
user, also remove the associated bits from the rest of U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As variables were moved to Kconfig, some of the surrounding ifdefs were
left around, even though they were empty. Clean them up.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
As this is the last SH4A board, remove that support as well.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Patch-cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Patch-cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Chris Packham <judge.packham@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lauri Hintsala <lauri.hintsala@silabs.com<mailto:lauri.hintsala@silabs.com>>
Signed-off-by: Tom Rini <trini@konsulko.com<mailto:trini@konsulko.com>>
Enable the fastboot oem command format and set the variable
"partitions" with default eMMC partitions list.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Jean-Philippe ROMAIN <jean-philippe.romain@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Espressobin: Set default env values at runtime (Pali)
- Espressobin: Set the maximum slave SPI speed to 40MHz (Pali)
- theadorable: PCIe test code enhancement and early deemphasis
enabling (Stefan)
- pci_mvebu: Disable config access to PCI host bridge ports (Stefan)
- mv_sdhci: parse device-tree entry (Baruch)
Cleanup, move the declarations to keymile/common.h instead declaring them
per-board config.h
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable SATA support. Although not supported by the usual SATA pins on
the SMARC baseboard connector, SATA mode is supported on a PCIe lane.
This way one can use a mSATA card in a Mini PCI slot.
We need to invert the received data because in this mode the polarity of
the SerDes lane is swapped. Provide a fixup in board_early_init_f() for
the SPL. board_early_init_f() is then not common between SPL and u-boot
proper anymore, thus common.c is removed, as it just contained said
function.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add COMMON_ENV(kernelheader_addr_r, fdtheader_addr_r,
kernel_addr_r, fdt_addr_r, load_addr)
to fix a bug that failed to boot to ubuntu
Failed log as follows,
## Executing script at 80000000
load - load binary file from a filesystemUsage:
load <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- Load binary file filename from partition part on device
type interface instance dev to address addr in memory.
bytes gives the size to load in bytes.
If bytes is 0 or omitted, the file is read until the end.
pos gives the file byte position to start reading from.
If pos is 0 or omitted, the file is read from the start.
...
Bad Linux ARM64 Image magic!
SCRIPT FAILED: continuing...
Signed-off-by: Biwen Li <biwen.li@nxp.com>
[Updated description]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
On Espressobin board are MAC addresses stored in U-Boot env area. Therefore
they are not present in default_environment[] array constructed at compile
time.
This change puts permanent MAC addresses into default_environment[] array
at board runtime. Espressobin board has enabled DEFAULT_ENV_IS_RW option
and therefore can modify this array.
This change ensure that 'env default -a' does not delete permanent MAC
addresses from Espressobin env storage area.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
On Espressobin board value for $fdtfile cannot be determined at compile
time and is calculated at board runtime code. This change uses a new option
DEFAULT_ENV_IS_RW to allow modifying default_environment[] array at runtime
and set into it correct value.
This change also ensure that 'env default -a' set correct value to $fdtfile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.
Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).
Signed-off-by: David Lechner <david@lechnology.com>
With the recent addition of ACPI generation, the image size has got beyond
its current limit.
Samus does not actually use this, nor x86 emulation for PCI ROMs, so
disable both features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Re-send because of line-wraps.
This patch fixes the behaviour of the menuconfig's BOOTCOMMAND
setting. Which is just ignored without that patch on
vexpress_aemv8a platform.
Signed-off-by: Stanislav.Pinchuk@kaspersky.com
- Espressobin: Disable slot when emmc is not present (Pali)
- DS414; config header cleanup (Phil)
- PCI: auto-config enhancement (Phil)
- pci_mvebu: Also map IO region (Phil)
- serial: a3720: Implement pending method for output direction (Pali)
- turris_mox: Enable a few commands (Marek)
- helios4 & ClearFog changes (Dennis)
- Plus some minor misc changes
Add CAxxxx Ethernet support for the Cortina Access
Presidio Engineering Board
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
A few minor changes:
* Get rid of leftover comments, other commits removed the defines they
referred to.
* CONFIG_SYS_NETA_INTERFACE_TYPE is not used anymore since commit
e3b9c98a23 ("net: mvneta: Convert to driver model").
* Drop CONFIG_USB_MAX_CONTROLLER_COUNT: it is per-HCI type, so XHCI and
EHCI could still both work be used.
* Unconditionally define CONFIG_EHCI_IS_TDI: it has no effect on XHCI so
that conditional doesn't make any sense.
* Define a larger PHY_ANEG_TIMEOUT: In my test bed, the NIC is directly
connected to some RTL8111 and the default 8s timeout was often too
short.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
This patch adds support for MediaTek MT7620 SoC.
All files are dedicated for u-boot.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Supported boot device types in iMX8MQ: MMC, DHCP.
CONFIG_DISTRO_DEFAULTS is added for enabling the DISTRO_DEFAULTS option.
CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mq_evk.h is
deleted because "run distro_bootcmd" is required to be the default boot
mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution.
kernel_addr_r is the location in RAM where the kernel will be loaded to.
Delete unnecessary environment variables because "run distro_bootcmd" is
set to be the default boot mode.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
This patch converts the dart6ul ethernet support to DM_ETH and cleans
up the legacy ethernet code. The clean up, more specifically:
* moves the fec2 node and pin definition to the carrier board DTS
since the phy associated with it is on the carrier board and not on
the SoM;
* add the reset pin associated to each phy;
* separate the ethernet, mdio and reset pins of each fec so that they
are easier to reference;
* add clock properties to the phy nodes since they are connected to the
50Mhz ENET[12]_TX_CLK clock of the SoC;
* remove CONFIG_BOARD_EARLY_INIT_F since the function is now empty.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Supported boot device types in iMX8MP: MMC.
CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is
for command fstype.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution. kernel_addr_r is the location in RAM where
the kernel will be loaded to. Delete unnecessary environment variables
because "run distro_bootcmd" is set to be the default boot mode.
On the iMX8MP platform I used, "mmc1" represents SD card and "mmc2"
represents eMMC.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Supported boot device types in iMX8MM: MMC, DHCP.
CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is
for command fstype.
CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mm_evk.h is
deleted because "run distro_bootcmd" is required to be the default boot
mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution.
kernel_addr_r is the location in RAM where the kernel will be loaded to.
Delete unnecessary environment variables.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
The DWMAC4 IP has the possibility to skip up to 7 AXI bus width size words
after the descriptor. Use this to pad the descriptors to cacheline size and
remove the need for noncached memory altogether. Moreover, this lets Tegra
use the generic cache flush / invalidate operations.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add low level platform initialization for the AST2600 SoC.
The 2-stage booting with U-Boot SPL are leveraged to support
different booting mode.
However, currently the patch supports only the booting from
memory-mapped SPI flash.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Set environment for Nand flash (U-boot 2020.04):
- add nand flash in the device tree
- add new default configuration file for G3 using parallel Nand
- set nand parameters in presidio_asic.h
Signed-off-by: Kate Liu <kate.liu@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds Microchip MPFS Icicle Kit support. For now, only
NS16550 Serial, Microchip clock, Cadence eMMC and MACB drivers are
enabled. The Microchip MPFS Icicle defconfig by default builds
U-Boot for S-Mode because U-Boot on Microchip PolarFire SoC will run
in S-Mode as payload of HSS + OpenSBI.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Added support for timer_early_get_count() and timer_early_get_rate()
This is mostly useful in tracing.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This enables configs necessary for using SPI. The environment is saved to
the very end of SPI flash. This is unlikely to be overwritten unless the
entire flash is reprogrammed.
This also supplies a default bootcommand. It loads an image and device tree
from the first partition of the MMC. This is a minimal/least effort
bootcmd, so suggestions (especially in the form of patches) are welcome. I
didn't set up distro boot because I think it is unlikely that any
general-purpose linux distros will ever be ported to this board.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Chrstopher Obbard <obbardc@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add CONFIG_SPL_PAD_TO for Gen5 and Arria 10. CONFIG_SPL_PAD_TO is set to
size of OCRAM.
This is preparation for image padding change in socfpgaimage.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Since SSBL is running in DRAM, it shall setup the stack in DRAM
instead of OCRAM which is occupied by SPL and handoff data.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Instead of loading u-boot proper image (u-boot.img), SPL
now loads FIT image (u-boot.itb) which includes u-boot
proper, ATF and u-boot proper's DTB.
For OS, u-boot now loads FIT images (kernel.itb) which
includes Linux Image and Linux's DTB.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
- DM support for OMAP PWM backlight
- USB host mode support for AM654
- Minor SPI fixes
- Add support k2g ice board with 1GHz silicon
- Fix GTC programming for K3 devices
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/8S/0cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKFkB/9NBJq/+sgHZXRaMlAu
ULNwOPoNsQxHQGwF88B1lC+H8LJjM+2gJ8MfJdWvHNlcSdtJjbWk0aQL+5LKSlyz
G7l3BZ+AIYMOeTXay5mNUKnekXIr7c8tLoX8FH/Ih+bHFPt57qL0bbfznV66UCOp
/o/yM8daPa9Kx1vPEpT2dC9bYXLXeQv6R+RMxwoc4Bk+R3OK7zoZ3Wdx0q9HvBwj
iWHM49X2fBqqi5RS+ZI37AUzi8iysD3fOq0kWTJcCNaci8i8RZdzSyoaDuXhA63I
EZJ7v9fUkW/bwTONVE9n2BX4xF9X/6R7P46l9dQISXAxsOBwsNRQPt8Ro7mCoc4K
392o
=LIK7
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2021.04 cycle
This feature set includes the new board SAMA7G5 EK, the new evaluation
kit for Microchip AT91 SAMA7G5 SoC . The current board support includes
two configurations for booting from eMMC (SDMMC0), SD-Card (SDMMC1), and
support for two Ethernet interfaces.
Those two commands now doing same thing, reading from ext2/3/4 filesystem.
So remove useless duplicated call.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
As more and more LINUX drivers are modified to use asynchronous probing
instead of synchronous probing, relying on device names being equal in
U-Boot and LINUX is not possible anymore. This is also true for block
device names like mmc0, mmc1 ect.
With LINUX kernel commit a1a4891 the probing type for the sdhci-omap
driver has been set to asynchronous mode too (probe_type is now
PROBE_PREFER_ASYNCHRONOUS).
In the case of the PDU001 board this results in the devices mmc0 and
mmc1 being swapped between U-Boot and LINUX. Device mmc0 in U-Boot
becomes mmc1 in LINUX an vice versa. Hence using device name identifiers
with LINUX kernel parameter root does not work anymore.
This patch changes the LINUX kernel boot parameter root to use the
pseudo (since we use MBR not GPT) partition UUID to locate the partition
hosting the root file system.
Signed-off-by: Felix Brack <fb@ltec.ch>
In include/dfu.h, if CONFIG_SYS_DFU_MAX_FILE_SIZE is not defined then it is
defined as CONFIG_SYS_DFU_DATA_BUF_SIZE. This is 128 KiB for a53 core and
20 KiB for r5 core. If a larger file is transferred using dfu then it
fails.
CONFIG_SYS_DFU_DATA_BUF_SIZE can not be increased as there is not enough
heap memory to be allocated for the buffer in case of R5 spl.
Fix this by defining CONFIG_SYS_DFU_MAX_FILE_SIZE as the default
CONFIG_SYS_DFU_DATA_BUF_SIZE value.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
So far we did not support the BootROM based FEL USB debug mode on the
64-bit builds for Allwinner SoCs: The BootROM is using AArch32, but the
SPL runs in AArch64.
Returning back to AArch32 was not working as expected, since the RMR
reset into 32-bit mode always starts execution in the BootROM, but not
in the FEL routine.
After some debug and research and with help via IRC, the CPU hotplug
mechanism emerged as a solution: If a certain R_CPUCFG register contains
some magic, the BootROM will immediately branch to an address stored in
some other register. This works well for our purposes.
Enable the FEL feature by providing early AArch32 code to first save the
FEL state, *before* initially entering AArch64.
If we eventually determine that we should return to FEL, we reset back
into AArch32, and use the CPU hotplug mechanism to run some small
AArch32 code snippet that restores the initially saved FEL state.
That allows the normal AArch64 SPL build to be loaded via the sunxi-fel
tool, with it returning into FEL mode, so that other payloads can be
transferred via FEL as well.
Tested on A64, H5 and H6.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Priit Laes <plaes@plaes.org> (on Olimex A64-Olinuxino)
The usage of the preboot feature is now controlled via a separate Kconfig
option - namely CONFIG_USE_PREBOOT.
It must be enabled for preboot code executing commands now defined in
CONFIG_PREBOOT (also moved to the Kconfig).
After defining both CONFIG_USE_PREBOOT and CONFIG_PREBOOT in
imx28_xea_defconfig the define of CONFIG_PREBOOT shall be removed from
xea.h as it is redundant.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Clean-up boot command to use the predefined device and part for FAT
environment.
According to this device and partition, select the proper boot media.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Heap base address is computed based on SYS_INIT_SP_ADDR by
subtracting the SYS_MALLOC_F_LEN value in
board_init_f_init_reserve().
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
Add parallel nor device to distroboot for microblaze.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Instead of hardcoding index magic numbers in the board code,
also rely on board_fit_config_name_match choosing the right
config for the fitImage containing the kernel.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since linux commit 2e6cde96873253fd9eb0f20afd8ffd18278cff75 ("arm64:
dts: ls1028a: make the eMMC and SD card controllers use fixed indices")
mmc0 is the eMMC and mmc1 is the SD card. Also swap it in u-boot to
avoid any confusion by the user and to be aligned with linux.
Signed-off-by: Michael Walle <michael@walle.cc>
Enable DM_SPI/DM_SPI_FLASH with a related config option.
Build fine, but not tested.
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI/DM_SPI_FLASH with a related config option.
Build fine, but not tested.
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Make use of the new bootargs substitution mechanism and zboot command
syntax.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
=cgbE
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Set `bootcause' from b850v3 power management watchdog status.
Boot cause "REVERT" is no longer used, remove it.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix typo in NFS command configuration check.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
Activate ARCH_SUPPORT_PSCI as other TEGRA124 target and remove
CONFIG_ARMV7_PSCI and CONFIG_ARMV7_PSCI_NR_CPUS in configs file as they
are migrated in Kconfig.
Select CONFIG_ARMV7_PSCI_0_1 (the first PSCI version),
because CONFIG_ARMV7_PSCI_0_2 and CONFIG_ARMV7_PSCI_1_0
are not activated in this product.
Hi,
This patch depend on the previous serie [1].
I don't test this patch on real hardware but
after this patch the size of the binary don't change.
In .config we have:
CONFIG_ARCH_SUPPORT_PSCI=y
CONFIG_ARMV7_PSCI=y
# CONFIG_ARMV7_PSCI_1_0 is not set
# CONFIG_ARMV7_PSCI_0_2 is not set
CONFIG_ARMV7_PSCI_0_1=y
CONFIG_ARMV7_PSCI_NR_CPUS=4
In u-boot.cfg, this patch only add the 2 lines
#define CONFIG_ARCH_SUPPORT_PSCI 1
#define CONFIG_ARMV7_PSCI_0_1 1
[1] "Convert CONFIG_ARMV7_PSCI_1_0 and CONFIG_ARMV7_PSCI_0_2 to Kconfig"
http://patchwork.ozlabs.org/project/uboot/list/?series=184029
Regards
Patrick
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Upstream linux DT naming doesn't align with the U-Boot DT, which may
not always be the case so this allows using BOOTENV_EFI_SET_FDTFILE_FALLBACK
where it might be appropriate for some boards.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For booting via UEFI we need to define the fdtfile option so
bootefi has the option to load a fdtfile from disk. For arm64
the kernel dtb is located in a vendor directory so we define
that as nvidia for that architecture.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was used for a board which is not supproted anymore and can
therefore be dropped.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This option is obsolete since 2009 and can be removed globally.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Address most of the checkpatch issues we found in km_arm and common km
code.
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no reason to define default option for this macro which is
already done in common/cli_hush.c.
87 #ifndef CONFIG_SYS_PROMPT_HUSH_PS2
88 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
89 #endif
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Remove fixed configuration and detect flash based on DT.
Also increase amount of flash sectors to 2048 because on kc705 flash has
1027 sectors.
Bank # 1: CFI conformant flash (16 x 16) Size: 128 MB in 1027 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8962
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
XIP is not enabled in SPL. SPL_NOR is enabled but any macro setting with
using SYS_FLASH_BASE are wrong because it is not aligned with DM.
That's why change these macro and align them with TEXT_BASE macro.
Information should be find at run time based on DT but implementation is
not done yet.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to use this file anymore. Include it in main config file
and simplify logic based on it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable caches by default. For now just simplify config file but it should
be read from DT or PVRs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A lot of configs has been moved to Kconfig and it ends up in ifdef mess
with no bodies. That's why remove all of them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Also change back SYS_MEMTEST_END to 0x00f00000. 0xe00000 was wrong and
introduced due to the global Kconfig migration of this option in u-boot.
CC: Heiko Schocher <hs@denx.de>
CC: Tom Rini <trini@konsulko.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Instead of using an hard coded address, make use of an
already defined address for importing the environment
for ramfs and nfs boot. This allows boards having different
mapping to use the same code.
CC: Heiko Schocher <hs@denx.de>
CC: Tom Rini <trini@konsulko.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
- meson64_android: don't show logo on ROM USB boot
- doc: update support matrix and fix vim3/l build instructions
- meson64: relocate config_distro_bootcmmd header
- Add a new SMBIOS parser and enable it when booting from coreboot
- Fix up various driver names to avoid dtoc warnings
- Fully enable ACPI support on Google Chromebook Coral
- Add a way to set SMBIOS properties using the devicetree
- Update existing boards to use devicetree for SMBIOS using a new
default sysinfo driver
Add a script to boot Chrome OS from the internal MMC. This involved adding
a few commands and options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Relocate a config_distro_bootcmd header before defined
CONFIG_EXTRA_ENV_SETTINGS. Otherwise it can't change to specific
environment.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
GE B1x5v2 patient monitor series is similar to the CARESCAPE Monitor
series (GE Bx50). It consists of a carrier PCB used in combination
with a Congatec QMX6 SoM. This adds U-Boot support using device model
everywhere and SPL for memory initialization.
Proper configuration is provided as 'ge_b1x5v2_defconfig' and the
combined image u-boot-with-spi.imx can be flashed directly to 1024
byte offset to /dev/mtdblock0. Alternatively SPL and u-boot.imx can
be loaded separately via USB-OTG using e.g. imx_usb.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board from Engicam.
PX30.Core needs to mount on top of this Evaluation board for
creating complete PX30.Core EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
When booting from rom usb, skip the boot logo logic as it's possible
that the partition containing the logo does not exist yet.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Fix up USB config options so keyboards and other USB devices work.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Change-Id: I34b0696e0ac7303186f20c83278dde340399b690
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
Add distro boot support for microblaze and enable jtag, qspi,
dhcp, pxe boot targets for distro boot.
Enable DISTRO_DEFAULTS config in microblaze defconfig and also
enable support for spi xilinx driver & spi vendors to access
spi flash by distro boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set proper indentation for env variables in microblaze header file.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Implement early init by calling generic board_init_f_alloc_reserve and
board_init_f_init_reserve functions:
* drop SYS_MALLOC_F_LEN related code, as allocation and gd->malloc_base
assignment are taken care of by the generic functions
* drop _gd logic
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Add basic support for the Kontron SMARC-sAL28 board. This includes just
the bare minimum to be able to bring up the board and boot linux.
For now, the Single and Dual PHY variant is supported. Other variants
will fall back to the basic variant.
In particular, there is no watchdog support for now. This means that you
have to disable the default watchdog, otherwise you'll end up in the
recovery bootloader. See the board README for details.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Instead having a hard coded value for "cramfsaddr" after compile time,
we change it to take the variable "cramfsaddr" for the ubicopy variable.
This makes sure that ubicopy uses the right address, even when
the value for "cramfsaddr" has changed.
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
CC: Heiko Schocher <hs@denx.de>
CC: Tom Rini <trini@konsulko.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Due to increasing kernel image sizes we get problems when decompressing
the kernel image. To fix this we need to change the addresses where we
load and where we extract the kernel. Also we need to adapt the address
where to load the CRAMFS image and where to load the DTB file.
While at it also harmonize all boards for PPC and ARM to have the
same values. Also we add a new variable "env_version", so that the
userspace is able to detect if this is a u-boot binary with updated
values or not.
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
CC: Heiko Schocher <hs@denx.de>
CC: Tom Rini <trini@konsulko.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Remove old values from kmp204x.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
As the ownership is now Hitachi Power Grids, change the license string
and adapt the compatible string in DTS files. For kmeter1.dts we
change it to "keymile,KMETER1" for now, as this is then compliant with
what is submitted to the linux kernel. All other boards don't have
a upstreamed version in linux mainline.
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
CC: Heiko Schocher <hs@denx.de>
CC: Marek Vasut <marex@denx.de>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl+NMmQcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLnEB/0cWFfjDfCMY1o7R4QX
DeDRlD6k6acQWlwa5EiRKwpbPMJKrSI/m5alMCYZG6YHvGtzihqnqohz3gl1sepi
W7eyyyFsM4hqe4P3lSETJRGWe/O8bNkoa0hBzqZ9btqw2OJLBu4JYB+zKgz8kaDY
jzkGLgaaK6wtG3rEu+q4fjzp1y9kuz31WnN+9qS8jd/9UH13XKCkJl9TfY5pLfgc
mmbn2NWtAhi91uShcnIsOpLaNm23IV0ITa22etB9F1docZuUrbhOtiIF45AADjpG
/xtkV3dEVGml3N/17RizgOwxX3xughG0ak9xifsK6tfgqfVhaGMgkToNNBM+1ddm
rZZM
=hF12
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.01 cycle:
This feature set brings the rework of the clock tree for sam9x60 SoC.
This makes the clock tree fully compatible with Common Clock Framework
and allows full clock configuration in U-Boot. This means that the
sam9x60 boards can boot now using U-Boot.
This also includes the definitions for sam9x60 SiPs and a divisor fix
for the clock on sama7g5 SoC.
Heap base address is computed based on SYS_INIT_SP_ADDR by
subtracting the SYS_MALLOC_F_LEN value in
board_init_f_init_reserve().
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Done with:
./tools/moveconfig.py VIDEO_BMP_GZIP
The 3 suspicious migration because CMD_BMP and SPLASH_SCREEN
are not activated in these defconfigs:
- trats_defconfig
- s5pc210_universal_defconfig
- trats2_defconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Unused.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In prepartion to remove CONFIG_DEFAULT_CONSOLE, fold the current users.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These are all unused.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These comments are relict for old, now removed config options.
So remove these obsoleted comments too.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Minor cleanup on K3 env variables
- Fix OSPI compatible for J721e
- Drop unused property in omap-usb2-phy
- Update Maintainer for am335x-guardian board.
Use DEFAULT_LINUX_BOOT_ENV to define the standard addresses used in rest
of TI platforms as defined in ti_armv7_common.h
This avoids the standard pitfalls we've had with kernel images and fdt
addresses stomping on each other.
As part of this process, redefine overlayaddr to be dtboaddr (defined
in ti_armv7_common.h for this very purpose) and get rid of the
definition of overlayaddr..
Signed-off-by: Nishanth Menon <nm@ti.com>
Use DEFAULT_LINUX_BOOT_ENV to define the standard addresses used in rest
of TI platforms as defined in ti_armv7_common.h
This avoids the standard pitfalls we've had with kernel images and fdt
addresses stomping on each other.
As part of this process, redefine overlayaddr to be dtboaddr (defined
in ti_armv7_common.h for this very purpose).. we will get rid of
overlayaddr later in the series.
Signed-off-by: Nishanth Menon <nm@ti.com>
Currently we hard-code the number and initial addresses of QEMU's flash
banks, even though our code is perfectly able to gather the same
information from the DTB provided by QEMU.
This is especially annoying, since we have two slightly different
U-Boot configurations ("bare-metal" vs. loaded via Arm Trusted
Firmware), which need to be selected at build time.
Drop the two hard coded alternatives, and use
CONFIG_SYS_MAX_FLASH_BANKS_DETECT instead, which relies on the DTB to
figure out the actual flash configuration at runtime.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch adds the board specific configuration (struct) for the
Octeon 3 EBB7304 EVK. This struct is ported from the 2013er Cavium /
Marvell U-Boot repository. Also, the Octeon RAM driver is enabled in
the board defconfig for its usage.
Tested with one and two DIMMs on the EBB7304 EVK (8 & 16 GiB).
Signed-off-by: Stefan Roese <sr@denx.de>
According to doc/README.distro fdt_addr must not be set when DTB is not
available from hardware. So remove this entry.
Use address 32MB above the start of DRAM for kernel_addr_r. This way
we likely can avoid the self-relocation of the compressed kernel image
before it decompresses to offset 0x8000 from start of DRAM.
Use address 128MB above the start of DRAM for fdt_addr_r, since this is
the maximum location for the end of the kernel. So we avoid overwriting
the DTB.
Use 512k above that for ramdisk_addr_r. This should be enough for the
DTB, rest of DRAM can be used for initrd.
Place boot script / extlinux.conf at offset 0 / 1MB from start of DRAM.
This space is available for processing in U-Boot.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965
Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF
accessible, mainline ATF is mandatory and must be built with
RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for
development and testing convenience only and must be disabled
in deployment for platform security reasons.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
Increase max gunzip size, required for booting itb recovery images on
uDPU.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
[a.heider: adapt to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However this call is missing for ls1028ardb and ls1028aqds boards. As
a result EFI boot doesn’t work. Fix this issue by removing custom
definition of scan_dev_for_boot and use the default definition
instead.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: andy.tang@nxp.com
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
PXE and DHCP shouldn't be listed when commands are not enabled that's why
handle it in the same way as is done for Zynq and ZynqMP.
Fixes: ec48b6c991 ("arm64: versal: Add support for new Xilinx Versal ACAPs")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch moves the the config SYS_MALLOC_LEN to Kconfig
as it is already done for zynq arch in commit 01aa5b8f05
("Kconfig: Move config SYS_MALLOC_LEN to Kconfig for zynq").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Provide fdtfile value in default env instead of setting
it dynamically in runtime.
Fixes: 85cb2bc686("apalis/colibri imx6: provide proper fdtfile value")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Provide fdtfile value in default env instead of setting
it dynamically in runtime.
Fixes: 85cb2bc686("apalis/colibri imx6: provide proper fdtfile value")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: a62c60610f("colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: 304042c1f3("colibri_vf: set fdtfile for distroboot")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: board: 31b1e17f44("toradex: add Colibri iMX6ULL support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 195011b24d("colibri-imx7: fix splash logo drawing")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 391c712dde("colibri-imx6ull: show boot logo")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
enable DTS support for keymile mpc83xx based boards.
get rid of compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Therefore done:
- add DTS for all mpc83xx based boards from keymile
mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
in board code, but not in linux DTS
- remove not used ethernet nodes
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Series-to: u-boot
Series-version: 3
Series-changes: 3
- rebase patchset to current mainline commit
c0192950df
- update defconfig files
Series-changes: 2
- add patch which fixes Codingstyle errors in drivers/qe
- add patch which converts the mpc83xx based boards from
keymile to DM_ETH
Cover-letter:
powerpc, mpc83xx: add DM_ETH support
This patch series adds DM ethernet support for mpc83xx based
keymile boards.
Travis build:
END
Add platform data and a device structure for the spi device
present on am335x-icev2. This requires moving all omap3_spi
platform data structures and symbols to an omap3_spi.h so that
the board file can access them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The R5 SPL on J7200 SoCs will be limited to booting just the
MCU R5FSS0 R5F core in LockStep-mode at present, so add the
two required environment variables 'addr_mcur5f0_0load' and
'name_mcur5f0_0fw' that are needed by the R5 SPL early-boot
logic. The firmware name used is also different from that on
J721E SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
The J7200 SoCs have different number of remote processors, but reuse
the same environment settings as the J721E SoCs. The current env
variable rproc_fw_binaries is geared towards J721E SoCs and is
incorrect for J7200 SoCs. Please see the logic originally added in
commit 0b4ab9c9a7 ("env: ti: j721e-evm: Add support to boot rprocs
including R5Fs and DSPs").
Fix this by defining the DEFAULT_RPROCS macro appropriately using
the corresponding TARGET_EVM Kconfig symbol. This macro is used by
the 'rproc_fw_binaries' env variable in the common remoteproc env
header file k3_rproc.h.
The list of R5F cores to be started before loading and booting the
Linux kernel are as follows, and mainly comprises of the Main R5FSS0
cores in this order:
Main R5FSS0 (Split) Core0 : 2 /lib/firmware/j7200-main-r5f0_0-fw
Main R5FSS0 (Split) Core1 : 3 /lib/firmware/j7200-main-r5f0_1-fw
The MCU R5FSS0 is in LockStep mode and is expected to be booted by
R5 SPL, so it is not included in the list. The order of rprocs to
boot cannot be really modified as only the Main R5FSS0 cores are
involved and Core0 has to be booted first always before the
corresponding Core1.
Signed-off-by: Suman Anna <s-anna@ti.com>
The commit 316c927135 ("include: configs: j721e_evm: Add env variables
for mcu_r5fss0_core0 & main_r5fss0_core0") added four different new env
variables 'addr_mainr5f0_0load', 'name_mainr5f0_0fw', 'addr_mcur5f0_0load'
and 'name_mcur5f0_0fw' to the generic environment, but these are only
needed and used in R5 SPL for early-booting the MCU R5FSS0 and Main
R5FSS0 Core0 on J721E SoCs.
These are not really needed for A72 U-Boot, so limit the scope of
these variables only to R5 SPL. While at this, also fix the loadaddr
variable values to include the hex prefix like with other such env
variables.
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
The default rproc list currently used by A72 U-Boot to boot various
remote processors include the Main R5FSS0 (Split-mode) Core1, Main
R5FSS1 (LockStep mode) Core0 and the three DSPs. The Main R5FSS1 cluster
is configured for Split mode by default in the dts now, so add the
Main R5FSS1 Core1 (rproc #5) to the default rproc boot list. This
core is now booted after the Main R5FSS1 Core0 and before the DSPs.
The order of the rprocs to boot can always be changed at runtime if
desired by overwriting the 'rproc_fw_binaries' environment variable
at U-boot prompt. Note that the R5FSS Core1 cannot be booted before
its associated Core0.
Signed-off-by: Suman Anna <s-anna@ti.com>
Boot scripts for existing Espressobin Linux distributions, like OpenWRT,
expect that U-Boot set fdt_addr and kernel_addr envs. So add env aliases
from fdt_addr_r and kernel_addr_r values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
Current loadaddr is not writable on Espressobin and 'loadb' command cause
rebooting board. Marvell's U-Boot already set default loadaddr to value
0x06000000 [1] and after this change 'loadb' is working fine.
[1] - 0a5b159806
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
According to Marvell's U-Boot description [1] current env load addresses
overlaps with ATF RT services region and TEE. Because the ATF RT service
and TEE region is going to be marked as secure and can't be overwritten,
use different different addresses for envs.
[1] - 0a5b159806
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel)
- Infrastructure changes to PCI uclass to support these SoC's (Suneel)
- Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel)
- Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
Restrict the memory range available for image processing in the
"bootm" to 256 MiB so the kernel can access it and FDT or initrd are
not overwritten on ARM64.
Signed-off-by: Grygorii Tertychnyi <grygorii.tertychnyi@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The loading address is too close to the kernel address, so newer kernels
may overlap memory space, so loading the device tree may corrupt zImage.
This patch moves the fdt_addr_r to 0x14000000 which is also consistent
with guidance that the kernel be allocated 32MB. This places it
in the same place as the ramdisk, so this patch moves the ramdisk address
512KB after the fdt.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
We have a number of platforms that are a combination of a carrier board
and System-on-Module (SoM) that in turn allows for the board to have
different SoCs on it. In some cases, this is handled via board-specific
Kconfig options. In other cases we make use of
CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid
configurations as we will not in turn get options that in Kconfig are
selected by or depend on that setting.
To resolve this, make the SoC option a choice in Kconfig and make boards
depend on what they can support. This change opens us up for further
clean-ups in the cases where a single CONFIG_TARGET_xxx can support
different SoCs and today they do not, or do not cleanly do so.
Reported-by: Matt Porter <mporter@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Soeren Moch <smoch@web.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ian Ray <ian.ray@ge.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Cc: Simone CIANNI <simone.cianni@bticino.it>
Cc: Adam Ford <aford173@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Parthiban Nallathambi <parthiban@linumiz.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Niel Fourie <lusus@denx.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Silvio Fricke <open-source@softing.de>
Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch adds support for all OcteonTX2 96xx/95xx
boards from Marvell.
For 96xx boards, use octeontx_96xx_defconfig and
for 95xx boards, use octeontx_95xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
This patch adds support for all OcteonTX 81xx/83xx
boards from Marvell.
For 81xx boards, use octeontx_81xx_defconfig and
for 83xx boards, use octeontx_83xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
CONFIG_CMD_RUN is set on by default in Kconfig.
Create xenguest_arm64_defconfig by using savedefconfig to avoid unnecessary
options.
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Total Compute is based on ARM architecture and has
the following features enabled in u-boot:
- PL011 UART
- PL180 MMC
- NOR Flash
- FIT image with Signature
- AVB
Signed-off-by: Usama Arif <usama.arif@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPLASH_SCREEN
CONFIG_SPLASH_SCREEN_ALIGN
CONFIG_SPLASHIMAGE_GUARD
CONFIG_SPLASH_SOURCE
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no need to setup this variable if bootm_low and bootm_size
variable are properly setup. If fdt_high variable is missing U-Boot is
asking LMB to return free memory which is not used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable DFU tftp support for firmware update. Fill dfu_ram_tftp variable to
have command present for showing how to use it.
boot FIT image has been created from below fragment. Key part is that type
of image has to be firmware. Also based on experiment load property is
completely ignored and base addresses are taken from dfu_alt_info variable.
$ cat update_uboot.its
/dts-v1/;
/ {
description = "Automatic U-Boot update";
#address-cells = <1>;
images {
Image {
description = "Kernel";
data = /incbin/("/tftpboot/Image");
compression = "none";
arch = "arm64";
type = "firmware";
os = "linux";
load = <0x80000>;
entry = <0x80000>;
hash-1 {
algo = "sha1";
};
};
system.dtb {
description = "DTB";
data = /incbin/("/tftpboot/system.dtb");
compression = "none";
arch = "arm64";
type = "firmware";
load = <0>;
hash-1 {
algo = "sha1";
};
};
};
};
$ mkimage -f update_uboot.its /tftpboot/boot
When U-Boot starts get IP address and server IP.
dhcp
setenv serverip 192.168.0.105
And then run prepared command.
run dfu_ram_tftp
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Image should be loaded to 0x80000 address and not to $kernel_addr_r.
Also kernel_addr, fdt_addr and fdt_size in zynqmp case are not defined
that's why define it to be aligned with Versal.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mini U-boot runs on lower foot print of 256KB OCM. Hence 8K memory
for malloc may not be required. Reduce it by 1.5K.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
