Commit graph

1930 commits

Author SHA1 Message Date
Dave Gerlach
f84880f0f3 ARM: AM43xx: Write sdram_config to secure_emif_sdram_config
The register secure_emif_sdram_config in control module is copied to
the EMIF sdram_config register when it is coming out of DeepSleep0 in
order to ensure that the EMIF comes up for the correct type of DDR.
Without this, resume can hang from within the kernel.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2014-03-04 09:42:07 -05:00
Dave Gerlach
4800be4a0c ARM: AM43xx: EMIF: configure self-refresh entry delay
Per a suggestion from the hardware team, program the emif_pwr_mgmt_ctrl
and emif_pwr_mgmt_ctrl_shdw registers within the EMIF to hold the
desired delay in cycles that the EMIF waits without an access to enter
self-refresh, in this case 8192 cycles. With this, code desiring to
enter self refresh only has to toggle one bit to enable it.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2014-03-04 09:42:07 -05:00
Mugunthan V N
2cab8ae85d ARM: AM43xx: clocks: Enable CPGMAC clock control
Enable CPGMAC clock control for AM43xx to use ethernet in U-Boot

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:06 -05:00
Tom Rini
eeb72e6761 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	arch/arm/cpu/armv7/config.mk
	board/ti/am43xx/mux.c
	include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 16:49:58 -05:00
Tom Rini
1551df35f2 arm: Switch to -mno-unaligned-access when supported by the compiler
When we tell the compiler to optimize for ARMv7 (and ARMv6 for that
matter) it assumes a default of SCTRL.A being cleared and unaligned
accesses being allowed and fast at the hardware level.  We set this bit
and must pass along -mno-unaligned-access so that the compiler will
still breakdown accesses and not trigger a data abort.

To better help understand the requirements of the project with respect
to unaligned memory access, the
Documentation/unaligned-memory-access.txt file has been added as
doc/README.unaligned-memory-access.txt and is taken from the v3.14-rc1
tag of the kernel.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 21:19:32 +01:00
Albert ARIBAUD
b60eff31f3 arm: remove unneeded symbol offsets and _TEXT_BASE
Remove the last uses of symbol offsets in ARM U-Boot.
Remove some needless uses of _TEXT_BASE.
Remove all _TEXT_BASE definitions.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-02-26 21:18:12 +01:00
Albert ARIBAUD
d0b5d9da5d arm: make _end compiler-generated
This prevents references to _end from generating absolute
relocation records.

This change is binary invariant for ARM targets.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-02-26 21:18:09 +01:00
Masahiro Yamada
4c48cfb58b arm: omap: delete unincluded omap-common/config.mk
arch/arm/cpu/armv7/omap-common/config.mk is never included
because "omap-common" is not SoC name.

If we want to add OMAP-specific compiler flags,
they must be added to omap3/config.mk, omap4/config.mk, omap5/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
2014-02-25 11:01:29 -05:00
Masahiro Yamada
630d23455b kbuild: refactor more IMX image rules
This commit avoids generating ./SPL twice.
  - Fist time descending to spl/
  - Second time as a prerequisite of u-boot-with-spl.imx,
    u-boot-with-nand-spl.imx.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-25 11:01:29 -05:00
Masahiro Yamada
4e0c8abcdd kbuild: use shorten logs for IMX images
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-25 11:01:29 -05:00
Masahiro Yamada
9bf215b035 kbuild: use shorten logs for mkimage rules
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-25 11:01:29 -05:00
Masahiro Yamada
95ddcd68ab kbuild: rename OBJCFLAGS to OBJCOPYFLAGS
Rename OBJCFLAGS to OBJCOPYFLAGS beforehand to use
"cmd_objcopy" in scripts/Makefile.lib in an upcoming commit.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-25 11:01:28 -05:00
Masahiro Yamada
f55e911ff4 arm: delete unused macro CONFIG_ARCH_DEVICE_TREE
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Rajeshwari Birje <rajeshwari.s@samsung.com>
Cc: Inderpal Singh <inderpal.singh@linaro.org>
2014-02-24 10:56:33 -05:00
Albert ARIBAUD
fae56934a0 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-02-24 10:29:59 +01:00
Darwin Rambo
989ce04999 arch: bcm281xx: Initial commit of bcm281xx architecture code
Add bcm281xx architecture support code including a clock framework and
chip reset.  Define register block base addresses for the bcm281xx
architecture and create an empty gpio header file required when
CONFIG_CMD_GPIO is set.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22 19:30:24 +01:00
Darwin Rambo
b3134fce89 arch: kona: Initial commit of kona-common architecture code
The Kona architecture is present on a number of Broadcom mobile SoCs
including the bcm281xx family of chips.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22 19:30:18 +01:00
Måns Rullgård
11f2968706 ti814x: Fix illegal use of FP ops in clock_ti814x.c
The function pll_sigma_delta_val uses "float" data which is not correct.
The exact "why" of this mangling is lost to history, but this changes us
to equivalent non-FP math to get the same results.

Reported-by: Wolfgang Denk <wd@denx.de>
Acked-by: Matt Porter <mporter@linaro.org>
2014-02-21 14:03:44 -05:00
Nishanth Menon
82da4410f8 DRA7: fix ABB efuse offset for OPP_NOM
commit 194dd74ad9
(DRA7: add ABB setup for MPU voltage domain)

Made an offset typo error by using 0x4A003B24 as the efuse offset
for OPP_NOM. As per TI documentation, 0x4A003B24 is for OPP_OD, and
0x4A003B20 is for OPP_NOM. Fix the same.

Reported-by: Praveen Rao <prao@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2014-02-21 13:55:41 -05:00
Janne Grunau
6e2192a3d8 ARM: OMAP4: fix DDR timings for OMAP4430 ES2.0
DDR timings were broken since 47abc3df70
for PandaBoard EA1.

Signed-off-by: Janne Grunau <j@jannau.net>
2014-02-21 13:55:41 -05:00
Dave Gerlach
cd8341b7eb ARM: AM43xx: GP-EVM: Correct GPIO used for VTT regulator control
Schematic indicates GPIO5_7 is to be used for VTT regulator control
rather than GPIO0_21 so modify enable_vtt_regulator to reflect this.
Without this some boards will experience DDR3 corruption and fail to
boot.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[trini: Rework patch against mainline]
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 13:55:40 -05:00
Tom Rini
4c89a369c7 Merge branch 'master' of git://git.denx.de/u-boot-spi 2014-02-21 08:00:22 -05:00
Albert ARIBAUD
3e11350255 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	Makefile
	drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
2014-02-20 13:16:05 +01:00
Masahiro Yamada
2aa43f70cf kbuild,tegra124: add dummy obj- for Kbuild
In Kbuild, every makefile must have non-empty obj- or obj-y.
Otherwise, built-in.o will not be created and the link stage
will fail.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 15:43:46 -05:00
Masahiro Yamada
ca53735a4c Move CONFIG_DISPLAY_CPUINFO to Makefile
If the whole code is surrounded by #ifdef(CONFIG_ ) .. #endif,
it should be moved to Makefile.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:10:05 -05:00
Masahiro Yamada
365475e6d1 Move #ifdef(CONFIG_DISPLAY_CPUINFO) from caller to callee
- When CONFIG_DISPLAY_CPUINFO is not enabled,
   print_cpuinfo() should be defined as an empty function
   in a header, include/common.h

 - Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
   from caller, common/board_f.c and arch/arm/lib/board.c

 - Remove redundant prototypes in arch/arm/lib/board.c,
   arch/arm/include/asm/arch-am33x/sys_proto.h and
   board/nokia/rx51/rx51.h, keeping the one in include/common.h

 - Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
   where it is missing

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:10:05 -05:00
Masahiro Yamada
7c8278a866 kbuild: add dummy obj-y to create built-in.o
We are going to switch over to Kbuild in upcoming commits.

Each makefile must have non-empty obj- or obj-y
to generate built-in.o on Kbuild.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:07:50 -05:00
Masahiro Yamada
9e4140329e kbuild: change out-of-tree build
This commit changes the working directory
where the build process occurs.

Before this commit, build process occurred under the source
tree for both in-tree and out-of-tree build.

That's why we needed to add $(obj) prefix to all generated
files in makefiles like follows:
  $(obj)u-boot.bin:  $(obj)u-boot

Here, $(obj) is empty for in-tree build, whereas it points
to the output directory for out-of-tree build.

And our old build system changes the current working directory
with "make -C <sub-dir>" syntax when descending into the
sub-directories.

On the other hand, Kbuild uses a different idea
to handle out-of-tree build and directory descending.

The build process of Kbuild always occurs under the output tree.
When "O=dir/to/store/output/files" is given, the build system
changes the current working directory to that directory and
restarts the make.

Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>"
syntax for descending into sub-directories.
(We can write it like "make $(obj)=<sub-dir>" with a shorthand.)
This means the current working directory is always the top
of the output directory.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
2014-02-19 11:07:50 -05:00
Dan Murphy
e9024ef27d ARM: O5/dra7xx: Add SATA boot support
Add the SATA boot support for OMAP5 and dra7xx.

Renamed the omap_sata_init to the common init_sata(int dev)
for commonality in with sata stack.

Added the ROM boot device ID for SATA.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-19 10:47:45 -05:00
Albert ARIBAUD
e7538fee99 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-02-19 12:04:45 +01:00
Siva Durga Prasad Paladugu
e158665c1e arm: zynq: correct the argument to lldiv
Typecast the argument with unsigned long long
for proper calculation of lldiv

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:22 +01:00
Michal Simek
d7e269cfbd zynq: Add support for U-BOOT SPL
SPL is using ps7_init.c/h files which are generated
from design tools which have to be copied to
boards/xilinx/zynq folder before compilation.

BSS section is moved to SDRAM because fat support
requires more space than SRAM size.

Added:
- MMC and QSPI support
- Boot OS directly from SPL
- Enable SPL command

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-02-19 09:41:22 +01:00
Michal Simek
96a5d4dc1e zynq: Update CLK in bdinfo
ARM has specific clk entries which should be also setup.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:22 +01:00
Soren Brinkmann
d6c9bbaad1 zynq: Implement dump clock command
Enable and implement dump clock command which shows
soc frequencies.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:22 +01:00
Soren Brinkmann
97598fcf10 net: zynq_gem: Calculate clock dividers dynamically
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Soren Brinkmann
1cd46ed2d3 net: zynq_gem: Move RCLK details out of driver
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Michal Simek
2826fd320c zynq: timer: Fix hangs if network activity attempted after about one hour
Cortex-A9 MPCore TRM' from ARM (ARM DDI 0407G ID072711) describes
in the section 4.1.1 how this value calculation should be done.

This patch fixes the problem if network activity such as ping or
tftp is attempted after u-boot has been idle for an hour,
it hangs, and cannot control-C out of it.

Signed-off-by: Uday Hegde <udayh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Soren Brinkmann
614c272511 zynq: timer: Migrate to zynq clock framework
Remove hardcoded frequencies in favor of Zynq clock framework.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Soren Brinkmann
6c3e61de3c zynq: Provide a framework to read clock frequencies
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Michal Simek
673ba27a85 zynq: Enable dcache support
Enable dcache.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:20 +01:00
Albert ARIBAUD
a87a0ce702 Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2014-02-19 07:15:01 +01:00
Sourav Poddar
b56e71e2d4 am43xx: Add qspi support
Add QSPI definitions and clock configuration support.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-02-18 22:41:08 +05:30
Tom Rini
c4d376fd1c Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-17 14:22:02 -05:00
Michal Simek
38716189d4 zynq: Fix elf header generation
This patch is here because of:
"arm: keep all sections in ELF file"
(sha1: 47ed5dd031)

Our tools expect to have elf with only LOAD header.
Without this fix also PHDR, INTERP and DYNAMIC headers
are available in ELF.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-13 15:33:00 +01:00
Stephen Warren
3cd534e455 ARM: bcm2835: config.mk isn't needed
The entries in config.mk were needed so that U-Boot could be built
with an old version of the Raspberry Pi Foundation's toolchain. Without
them, the build would error out with:

...-ld: error: .../libgcc.a(_bswapsi2.o) uses VFP register arguments,
u-boot does not

However, none of the 3 toolchains in the latest version of their
tools.git, nor the Ubuntu/Linaro ARM compilers in at least Ubuntu Quantal
or Saucy, need these options set in order to compile a working U-Boot.
Hence, remove the options for simplicity.

Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
2014-02-13 15:06:02 +01:00
Albert ARIBAUD
d53ccdb341 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-02-13 13:30:54 +01:00
Stefano Babic
17998eff90 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-11 12:55:32 +01:00
Markus Niebel
adadc915b3 ARM: imx6: fix wrong fec clk
imx_get_fecclk() returns enet_ref instead of ipg.
Since the clock is used to calculate the prescaler
for the MDIO interface wrong values can be calculated.

Tested on a custom MX6S board with 100MBit interface

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
2014-02-11 11:31:52 +01:00
Fabio Estevam
6d73c23410 mx6: Enable L2 cache support
Add L2 cache support and enable it by default.

Configure the L2 cache in the same way as done by FSL kernel:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_4.1.0

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-02-11 11:24:12 +01:00
Fabio Estevam
94db665579 mx6: Distinguish mx6dual from mx6quad
Currently when we boot a mx6dual U-boot reports that it is a mx6quad.

Report it as MX6D instead:

CPU:   Freescale i.MX6D rev1.2 at 792 MHz

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:24:12 +01:00
Anson Huang
16197bb8ba imx6: make sure MMDC_CHx_MASK is clear to avoid warm reset failure
Boot ROM may mask MMDC_CHx_MASK in CCM_CCDR(such as i.MX6SL TO1.2),
it will cause warm reset fail, need to clear this MMDC_CHx_MASK field
to make sure all the i.MX6 series SOCs reset function work. Otherwise,
uboot "reset" command will fail, tested on i.MX6SL EVK board with TO1.2.

Signed-off-by: Anson Huang <b20788@freescale.com>
2014-02-11 11:24:01 +01:00
Anson Huang
5c92edc21c imx6: ensure AHB clock is 132MHz in low freq boot mode
For low freq boot mode(ARM boot up with 396MHz), ROM
will not set AHB clock to 132MHz, and the reset value of
AHB divider is incorrect which will lead to wrong AHB
rate, need to correct it. To enable low freq boot mode,
need to set BOOT_CFG2[2] to high, tested on i.MX6Q/DL
SabreSD board and i.MX6SL EVK board.

Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Anson Huang <b20788@freescale.com>
2014-02-11 11:17:10 +01:00
Inha Song
e25bfecf7b exynos: clock: use the clear and set bits macros.
Use setbits/clrbits macro instead of readl/writel function.
(Suggested by Wolfgang)

Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-10 16:01:44 +09:00
Inha Song
3cb007a9f2 exynos: clock: fixed that cfg is set to wrong value.
This patch fixed that cfg value is set to wrong value.
Because it didn't read the related register.

Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-10 16:00:27 +09:00
Tom Rini
7dbe63bc95 SPL: Add CONFIG_SUPPORT_EMMC_BOOT support to CONFIG_SPL_FRAMEWORK
We use the switch CONFIG_SUPPORT_EMMC_BOOT today to enable some
additional features of the eMMC boot partitions.  Add support for being
told that we have booted from one of these partitions to the spl
framework and implement this on TI OMAP/related.

Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:48 +02:00
Marek Vasut
c8d4b2f826 ARM: IXP: Remove the IXP architecture support
The architecture is unmaintained and dead, remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:52 +01:00
Minkyu Kang
0ab9a03ca4 exynos: pinmux: remove unnecessary routine
Because of the list of peripherals is not sequential,
such a routine does not check for valid correctly.
Error check will be done when call the exynos_pinmux_config function.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
2014-02-05 15:37:56 +09:00
Minkyu Kang
1501cc9416 exynos: pinmux: remove unnecessary define
The value of PERIPH_ID_COUNT was wrong, and unnecessary.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-05 15:37:56 +09:00
Tom Warren
2f5dac9214 ARM: tegra: add common (shared) CPU files
These files are used by both SPL and main U-Boot.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Tom Warren
52ef43b052 ARM: tegra: Add CPU (armv7) files for Tegra124
These files are for code that runs on the CPU (A15) on Tegra124 boards.
At this time, there is no A15-specific code here. The warmboot/LP0 files
aren't included as that code hasn't been ported yet.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Tom Warren
32edd2ede2 ARM: tegra: add SPL/AVP (arm720t) CPU files for Tegra124
This provides SPL support for Tegra124 boards - AVP early init, plus
CPU (A15) init/jump to main U-Boot.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Stephen Warren
a4bcd67c72 ARM: tegra: remove a conditional for CSITE rate
There's already an SoC-specific conditional in cpu.h to determine the
PLLP rate. Define the CSITE clock rate inside the same conditional, so
that we can remove a conditional from clock_enable_coresight(). This
means one less place to update the code for new SoCs.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Stephen Warren
41447fb2cf ARM: tegra: enable PLLX only once it's been fully configured
This programming sequence is correct per Jimmy Zhang, and makes sense
too!

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Stephen Warren
cad38a57d3 ARM: tegra: pass just partition ID to power_partition()
Pass just the partition ID to power_partition(), rather than also passing
the partition's status register mask too. This makes it simpler to get
call-sites correct, since they don't need to pass two different values
that define the same thing and must match.

Consequently, we can remove the mask definitions from pmc.h.

Suggested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Stephen Warren
41cd530d6d ARM: tegra: misc cleanups triggered by Tegra124 review
Use a named constant for the PLL lock bit in enable_cpu_clocks().

Construct the complete value of pmc_pwrgate_toggle, rather than doing a
read-modify-write; the register is simple enough and doesn't need to
maintain state between operations.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Jimmy Zhang
b9dd6215ce ARM: tegra: don't exceed AVP limits when configuring PLLP
Based on the Tegra TRM, the system clock (which is the AVP clock) can
run up to 275MHz. On power on, the default sytem clock source is set to
PLLP_OUT0. In function clock_early_init(), PLLP_OUT0 will be set to
408MHz which is beyond system clock's upper limit.

The fix is to set the system clock to CLK_M before initializing PLLP,
and then switch back to PLLP_OUT4, which has an appropriate divider
configured, after PLLP has been configured

Implement this logic in new function tegra30_set_up_pllp(),
which sets up PLLP and all PLLP_OUT* dividers, and handles the AVP
clock switching. Remove the duplicate PLLP setup from pllx_set_rate()
and adjust_pllp_out_freqs().

Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
[swarren, significantly refactored the change]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Stephen Warren
9399e540ca ARM: tegra: amend pmc.h for Tegra114+
Tegra114 and later's PMC module removes the pwrgate_timer_on register
and replaces it with a clamp_status register. Adjust pmc.h to reflect
this, and update any code affected by the change.

The cpu.c change in this patch was extracted from a much larger patch
by Jimmy Zhang. The pmc.h change was written from scratch, but inspired
by related changes made by Tom Warren.

There could well be other differences in the PMC register set for chips
after Tegra20/30. However, they don't affect the code in U-Boot at
present, so I haven't attempted an exhaustive update of pmc.h.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Tom Warren
c82014daf5 ARM: tegra: implement MASK_BITS_31_29
Some clock sources have 3-bit muxes in bits 31:29. Implement core
support for this mux field.

Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, extracted from a larger patch by Tom]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Stephen Warren
54d2e18292 ARM: tegra: use MASK_BITS_* macros everywhere
Not all code that set or interpreted "mux_bits" was using the named
macros, but rather some was simply using hard-coded integer constants.
This makes it hard to determine which pieces of code are affected by
changes to those constants.

Replace the integer constants with the equivalent macro definitions so
that everything is nicely tied together.

Note that I'm not convinced all the code was using the correct integer
constants, and hence I'm not convinced that all the code is now using
the desired macros. However, this change is a purely mechanical
replacement and should have no functional change. Fixing any bugs will
come later, separately.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Stephen Warren
9cb0c6dc69 ARM: tegra: rename OUT_CLK_SOURCE_*
OUT_CLK_SOURCE_ are currently named after the number of bits the mask
they represent includes. However, bit count is not the only possible
variable; bit position may also vary. Rename OUT_CLK_SOURCE_ to
OUT_CLK_SOURCE_31_30_ and OUT_CLK_SOURCE4_ to OUT_CLK_SOURCE_31_28 to
more completely describe exactly what they represent, without having to
go look up the definitions.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Stephen Warren
5916a36ee9 ARM: tegra: rename MASK_BITS_29_28 to MASK_BITS_31_28
The only place where the MASK_BITS_* values are used is in
adjust_periph_pll(), which interprets the value 4 (old MASK_BITS_29_28,
new MASK_BITS_31_28) as being associated with mask OUT_CLK_SOURCE4_MASK,
i.e. bits 31:28. Rename the MASK_BITS_ macro to reflect how it's actually
implemented.

Note that no Tegra clock register actually uses all of bits 31:28 as
the mux field. Rather, bits 30:28, 29:28, or 28 are used. However, in
those cases, nothing is stored in the bits above the mux field, so it's
safe to pretend that the mux field extends all the way to the end of the
register. As such, the U-Boot clock driver is currently a bit lazy, and
doesn't distinguish between 31:28, 30:28, 29:28 and 28; it just lumps
them all together and pretends they're all 31:28. This patch doesn't
cause this issue; it was pre-existing. Hopefully, future patches will
clean this up.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Tom Warren
0b01b53aa5 ARM: tegra: deduplicate MASK_BITS_xxx clock mux enum
The enum used to define the set of register bits used to represent a
clock's input mux, MUX_BITS_*, is defined separately for each SoC at
present. Move this definition to a common location to ease fixing up
some issues with the definition, and the code that uses it.

Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, extracted from a larger patch by Tom]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:44 -07:00
Stephen Warren
86b657878b ARM: tegra: accept any SKU ID for most chips
For Tegra20, the SKU ID actually impacts how U-Boot programs the chip,
and hence we need to explicitly know about each and every SKU ID in order
to operate correctly.

However, for Tegra30/114, this isn't the case. Rather than forcing each
new user with a different SKU to manually add their SKU ID into the code,
simply accept any SKU ID.

If U-Boot ever starts e.g. programming maximal CPU clocks etc., we'll
need to undo this, or make the default case map to conservative defaults,
but for now it's likely the path to least support cost.

Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:44 -07:00
Albert ARIBAUD
e97f9d817e Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-01-29 14:07:50 +01:00
Marek Vasut
7981449280 ARM: mx6: Add PCI express clock configuration
Split the SATA clock enabling function and add PCI express clock
enabling function. The SATA clock enabling function starts up the
100MHz SATA reference PLL in ENET_PLL register, but the code can
be re-used to enable the 125MHz PCIe reference in ENET_PLL, so pull
this code into separate function. Moreover, add the PCIe clock
enabling code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-01-26 12:41:20 +01:00
Marek Vasut
7cbe638e41 ARM: armv7: Make indirect vector addresses globl
Make indirect vectors addresses global, so they can be replaced by
various code that needs to do so. For example the MX6 PCI express
driver needs to temporarily replace data abort handler when reading
the config space.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2014-01-26 12:41:20 +01:00
Stefano Babic
707acd01de Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-01-26 12:11:54 +01:00
Masahiro Yamada
bf1af3d872 ARM: merge commonly-defined PLATFORM_RELFLAGS
Before this commit, all arch/arm/cpu/${CPU}/config.mk except ARMv8
had the same option:
$(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,))

This commit moves it into arch/arm/config.mk.

If the compiler does not support the option,
it is ignored by $(call cc-option,...).
So this commit gives no harm to ARMv8.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:08 -05:00
Darwin Rambo
de351d6be6 lib: time: add weak timer_init() function
If timer_init() is made a weak stub function, then it allows us to
remove several empty timer_init functions for those boards that
already have a timer initialized when u-boot starts. Architectures
that use the timer framework may also remove the need for timer.c.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
2014-01-24 16:59:06 -05:00
Nishanth Menon
194dd74ad9 DRA7: add ABB setup for MPU voltage domain
Patch adds modification to shared omap5 abb_setup() function, and
proper registers definitions needed for ABB setup sequence. ABB is
initialized for MPU voltage domain at OPP_NOM.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-01-24 11:41:17 -05:00
Nishanth Menon
3ac8c0bf65 DRA7: Add support for ES1.1 silicon ID code
ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support
for ES1.1 IDCODE change.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-01-24 11:41:17 -05:00
Jassi Brar
e81f63f0d2 ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALL
The commit
f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2014-01-24 09:38:39 -05:00
Jassi Brar
02c41535b6 ARM: OMAP4/5: Remove dead code against CONFIG_SYS_CLOCKS_ENABLE_ALL
The commit
 f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2014-01-24 09:34:22 -05:00
Stephen Warren
004c10598b ARM: bcm2835: fix mailbox timeout
My original intention was to have a 100ms timeout. However, the timer
operations used return values in ms not us, so we ended up with a 100s
timeout instead. Fixing this exposes that some operations need longer
to operate than 100ms, so bump the timeout up to a whole second.

Reported-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-01-20 17:11:39 -05:00
Tom Rini
4641c211f6 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-01-20 07:33:42 -05:00
Fabio Estevam
be2a3bb39a mx6: Revert "mx6: soc: Disable VDDPU regulator"
Commit 022298278 (mx6: soc: Disable VDDPU regulator) is causing kernel hang
for people using FSL kernel 3.0.35 and 3.10, so revert it for now.

Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Reported-by: Pierre Aubert <p.aubert@staubli.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-17 10:16:48 +01:00
Albert ARIBAUD
bf46e7d8d1 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-01-15 15:18:04 +01:00
Fabio Estevam
5f98d0b5d3 mx6: clock: Pass the frequency as argument of enable_fec_anatop_clock()
Provide an argument to enable_fec_anatop_clock() to specify the clock frequency
that will be generated.

No changes are made to mx6slevk, which uses the default 50MHz fec clock.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-15 10:33:25 +01:00
Andreas Bießmann
6ba2bc8fa9 arm: use canonical sub mnemonic
Building some arm boards with older binutils may produce errors like this:

---8<---
crt0.S: Assembler messages:
crt0.S:70: Error: register expected, not '#(184)' -- `sub sp,#(184)'
--->8---

Use canonical version of the subtract mnemonic to avoid those issues.

Reported-by: Alexey Smishlayev <alexey@xtech2.lv>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-01-14 12:38:47 +01:00
Albert ARIBAUD
e6fe4bd989 Merge 'u-boot-imx/master' into 'u-boot-arm/master' 2014-01-14 11:50:54 +01:00
Albert ARIBAUD
b02bfc4dfc arm: put .hash, .got.plt and .machine_param back in binaries
Some targets will build fine but not boot if sections .hash and
.got.plt are not present in the binary. Add them back.

Also, Exynos machines require .machine_param section in SPL.
Add it.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
2014-01-14 11:43:10 +01:00
Marek Vasut
67decc71ed ARM: pxa: Fix OneNAND SPL builds
The OneNAND SPL used on PXA is slightly obscure. Due to the OneNAND limitation,
where we have only the first 1KiB of the OneNAND available upon power-up as a
memory-mapped area, from which the CPU starts executing, we place only the most
essential code into this first 1KiB . This code copies the rest of the SPL into
SRAM and jumps to it. This code is stored in section .text.0 .

The rest of the SPL is stored in section .text.1 . When running the OBJCOPY on
the SPL, it will preserve only .text section, but the .text.0 and .text.1 are
stripped away from the result, thus making the SPL binary empty. The patch adds
additional -j parameters to the OBJCOPY for PXA during the SPL build, which will
preserve the .text.0 and .text.1 sections.

Moreover, this patch also adds missing functions into the .text.0 section, since
otherwise the PXA270 with 1KiB-window OneNAND won't be able to boot.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
2014-01-13 12:39:10 +01:00
Christian Gmeiner
5a66016987 imx6: make use of lldiv(..)
Commit 762a88ccf8 introduces
a 64-bit division without using the lldiv() function,
which pulls in previously unused libgcc stuff.

Signed-off-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-13 11:52:28 +01:00
Tom Rini
7f673c99c2 Merge branch 'master' of git://git.denx.de/u-boot-arm
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.

Conflicts:
	include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-01-10 10:56:00 -05:00
Jagannadha Sutradharudu Teki
b3de92495f zynq: Add support to find bootmode
Added support to find the bootmodes by reading
slcr bootmode register. this can be helpful to
autoboot the configurations w.r.t a specified bootmode.

Added this functionality on board_late_init as it's not
needed for normal initializtion part.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
David Feng
0ae7653128 arm64: core support
Relocation code based on a patch by Scott Wood, which is:
Signed-off-by: Scott Wood <scottwood@freescale.com>

Signed-off-by: David Feng <fenghua@phytium.com.cn>
2014-01-09 16:08:44 +01:00
Albert ARIBAUD
4b0561d841 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-01-06 09:32:42 +01:00
Albert ARIBAUD
a891601ce5 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Conflicts:
	include/micrel.h

The conflict above was trivial, caused by four lines being
added in both branches with different whitepace.
2014-01-06 08:49:58 +01:00
Sergey Alyoshin
4611d5bab2 arm: mx5: Add fuse supply enable in fsl_iim
Enable fuse supply before fuse programming and disable after.

Signed-off-by: Sergey Alyoshin <alyoshin.s@gmail.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2014-01-03 15:44:06 +01:00
Otavio Salvador
c655b816e5 ARM: mx6: Allow enablement of FEC Anatop based clock for all MX6
The enable_fec_anatop_clock method should be available for all MX6
variant as it is not MX6 SoloLite specific. This moves the code out of
the #ifdef/#endif and we make it conditional to CONFIG_FEC_MXC
instead.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-03 15:44:05 +01:00
Fabio Estevam
0222982780 mx6: soc: Disable VDDPU regulator
As U-boot does not use GPU/VPU peripherals, shutdown the VDDPU regulator
in order to save power.

Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:51 +01:00
Fabio Estevam
39f0ac9347 mx6: soc: Add the required LDO ramp up delay
When changing LDO voltages we need to wait for the required amount of time
for the voltage to settle.

Also, as the timer is still not available when arch_cpu_init() is called, we
need to call it later at board_postclk_init() phase.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:51 +01:00
Fabio Estevam
3d622b78bd mx6: soc: Introduce set_ldo_voltage()
Introduce set_ldo_voltage() so that all three LDO regulators can be configured.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:51 +01:00
Fabio Estevam
7e5e8c94a9 mx6: soc: Set the VDDSOC at 1.175 V
mx6 datasheet specifies that the minimum VDDSOC at 792 MHz is 1.15 V.
Add a 25 mV margin and set it to 1.175V.

This also matches the VDDSOC voltages for 792MHz operation that the kernel configures:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/cpu_op-mx6.c?h=imx_3.0.35_4.1.0

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:50 +01:00
Fabio Estevam
e113fd1972 mx6: soc: Clear the LDO ramp values up prior to setting the LDO voltages
Since ROM may modify the LDO ramp up time according to fuse setting,
it is safer to reset the ramp up field to its default value of 00:

00: 64 cycles of 24MHz clock;
01: 128 cycles of 24MHz clock;
02: 256 cycles of 24MHz clock;
03: 512 cycles of 24MHz clock;

Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:50 +01:00
Fabio Estevam
fc740648bd mx6: soc: Staticize set_vddsoc()
set_vddsoc() is not used anywhere else, so make it static.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:50 +01:00
Rajeshwari Birje
5af4a4f74a Exynos5420: Add support for 5420 in pinmux and gpio
Adds code in pinmux and gpio framework to support Exynos5420.

Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30 16:50:34 +09:00
Rajeshwari Birje
f3d7c2fe9d Exynos5420: Add DDR3 initialization for 5420
This patch intends to add DDR3 initialization code for Exynos5420.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30 16:50:34 +09:00
Rajeshwari Birje
060c227a28 Exynos5420: Add clock initialization for 5420
This patch adds code for clock initialization and clock settings
of various IP's and controllers, required for Exynos5420

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30 16:50:34 +09:00
Lokesh Vutla
b5e01eecc8 ARM: AM43xx: GP_EVM: Add support for DDR3
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:45 -05:00
Lokesh Vutla
d3daba10f1 ARM: AM43xx: EPOS_EVM: Add support for LPDDR2
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:44 -05:00
Lokesh Vutla
965de8b91b ARM: AM33xx+: Update ioregs to pass different values
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-18 21:14:18 -05:00
Lokesh Vutla
cf04d0326b ARM: AM43xx: clocks: Update DPLL details
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50	300MHz
OPP100	600MHz
OPP120	720MHz
OPPTB	800MHz
OPPNT	1000MHz
According to the latest DM following is the OPP table dependencies:
	VDD_CORE 	VDD_MPU
	OPP50		OPP50
	OPP50 		OPP100
	OPP100		OPP50
	OPP100		OPP100
	OPP100		OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz

Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:01 -05:00
Lokesh Vutla
0d54cb924e ARM: AM43xx: Select clk source for Timer2
Selecting the Master osc clk as Timer2 clock source.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:01 -05:00
Albert ARIBAUD
d627eefcd5 Merge remote-tracking branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2013-12-18 22:19:02 +01:00
Alban Bedel
3346cbb8e8 ARM: tegra: support SKU b1 of Tegra30
Add the Tegra30 SKU b1 and treat it like other Tegra30 chips.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Julian Scheel <julian.scheel@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-18 10:19:48 -07:00
Thierry Reding
4475c7752d Tegra114: Do not program CPCON field for PLLX
PLLX no longer has the CPCON field on Tegra114, so do not attempt to
program it.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-18 10:19:48 -07:00
Jimmy Zhang
44de8e22ec Tegra114: Fix PLLX M, N, P init settings
The M, N and P width have been changed from Tegra30. The maximum value
for N is limited to 255. So, the tegra_pll_x_table for Tegra114 should
be set accordingly.

Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Reviewed-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-18 10:19:48 -07:00
Sergei Ianovich
23f00caf6e ARM: pxa: prevent PXA270 occasional reboot freezes
Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.

If SDRAM is not reset, it causes memory bus congestion and
the device hangs.

We put SDRAM in selfresh mode before watchdog reset, removing
potential freezes.

Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
2013-12-18 16:00:37 +01:00
Frank Li
ebaf6b26bc imx6: fix random hang when download by usb
ROM did not invalidate L1 cache when download by usb
Need invalidate L1 cache before enable cache

Signed-off-by: Huang yongcai <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
2013-12-17 18:48:45 +01:00
Fabio Estevam
89cfd0f575 mx6: clock: Fix the calculation of PLL_ENET frequency
According to the mx6 quad reference manual, the DIV_SELECT field of register
CCM_ANALOG_PLL_ENETn has the following meaning:

"Controls the frequency of the ethernet reference clock.
- 00 - 25MHz
- 01 - 50MHz
- 10 - 100MHz
- 11 - 125MHz"

Current logic does not handle the 25MHz case correctly, so fix it.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-12-17 18:38:42 +01:00
Tom Rini
49a90e2975 ARM:PXA: Correct tick_to_time / us_to_tick to use lldiv
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
2013-12-13 09:16:20 -05:00
Tom Rini
e83bab8403 ARM:zynq: Correct __udelay to use lldiv
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-13 09:16:20 -05:00
Lokesh Vutla
d2c7074b95 ARM: OMAP5: clocks: Update MPU settings for OPP_NOM
As per the latest 0.6 version of DM for OMAP5430 ES2.0,
MPU_GCLK is given as 1000MHz. In order to achieve this DPLL_MPU
should be locked at 2000MHz. Fixing the same and cleaning the
previously used dpll values.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-12 17:43:39 -05:00
Lokesh Vutla
5298f21ab3 ARM: DRA7xx: Change clk divider setting
Commit "armv7: hw_data: change clock divider setting"
updates the setting for m6 divider for 20MHz sys_clk frequency.
But missed to update for other sys_clk frequencies. Doing the same.

Reported-by: Rajendran, Vinothkumar <vinothr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-12 17:43:39 -05:00
Nikita Kiryanov
47b4bcf785 arm: omap: abb: add missing include
ABB code uses LDELAY but does not include the header that provides its
definition.

Include the header.

Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Nishanth Menon <nm@ti.com>
2013-12-12 14:54:22 -05:00
Tom Rini
12115c6ad3 am33xx: Enable D-CACHE on !CONFIG_SYS_DCACHE_OFF
Test on Beaglebone white over cpsw, usb ether and SD card (read and
write), performance increased, crc32 of data matches.

Signed-off-by: Tom Rini <trini@ti.com>
2013-12-12 14:54:12 -05:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00
Andreas Bießmann
bcf9fe37f5 at91: switch coloured LED to gpio API
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-09 13:21:47 +01:00
Albert ARIBAUD
47ed5dd031 arm: keep all sections in ELF file
Current LDS files /DISCARD/ a lot of sections when linking ELF
files, causing diagnostic tools such as readelf or objdump to
produce partial output. Keep all section at link stage, filter
only at objcopy time so that .bin remains minimal.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-12-07 06:53:58 +01:00
Masahiro Yamada
3064d599af ARM: align MVBAR on 32 byte boundary
The lower 5 bit of MVBAR is UNK/SBZP.
So, Monitor Vector Base Address must be 32-byte aligned.
On the other hand, the secure monitor handler does not need
32-byte alignment.

This commit moves ".algin 5" directive to the correct place.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andre Przywara <andre.przywara@linaro.org>
Acked-by: Andre Przywara <andre.przywara@linaro.org>
2013-12-06 21:03:35 +01:00
Albert ARIBAUD
375a4496ff Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2013-12-06 16:54:42 +01:00
Albert ARIBAUD
c35cf8dc9f Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-12-06 14:26:51 +01:00
Michael Trimarchi
f33b9bd398 arm: omap3: Enable clocks for peripherals only if they are used
This patch change the per_clocks_enable() function used in OMAP3
code to enable peripherals clocks. Only required clock should be
activated. So if the board use the uart(x) as a console we need
to activate it. The Board's config should include define to enable
every subsystem that the board use. For a complete list
of affected peripherals, registers CM_FCLKEN_PER and CM_ICLKEN_PER
should be checked.
Right now the bootloader can enable and disable clocks for:
uart(x) using CONFIG_SYS_NS16550
gpio bank (x) using CONFIG_OMAP3_GPIO_X with X = { 2, 3, 4, 5, 6 }
i2c bus using CONFIG_DRIVER_OMAP34XX_I2C.

Not required gptimer(x) and mcbsp(x) for booting are disabled by default and
are not supported by any define.
Their activation need to included in the per_clocks_enable if the
peripheral is included. Not booting board should enable the peripheral
clock connected to their driver

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-12-06 07:02:32 -05:00
Minkyu Kang
d8fa31a71f arm: exynos: adds ifdef for spi boot
This patch fix following errors and warnings

spl_boot.c: In function 'exynos_spi_copy':
spl_boot.c:111:49: error: 'CONFIG_ENV_SPI_BASE' undeclared (first use in this function)
spl_boot.c:111:49: note: each undeclared identifier is reported only once for each function it appears in
spl_boot.c:142:2: error: 'SPI_FLASH_UBOOT_POS' undeclared (first use in this function)
spl_boot.c: In function 'copy_uboot_to_ram':
spl_boot.c:189:28: warning: unused variable 'param' [-Wunused-variable]
spl_boot.c: At top level:
spl_boot.c:107:13: warning: 'exynos_spi_copy' defined but not used [-Wunused-function]

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-12-06 19:07:47 +09:00
Albert ARIBAUD
7988bd4ed6 Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master' 2013-12-06 10:41:49 +01:00
Hardik Patel
675cc77a3a pandaboard: 1/1] ARM:OMAP4+: panda-es: Support Rev B3 Elpida DDR2 RAM
Signed-off-by: Hardik Patel <hardik.patel@volansystech.com>
2013-12-04 11:41:13 -05:00
Lokesh Vutla
642cdc13f6 ARM: OMAP5+: Remove unnecessary EFUSE settings
Certain EFUSE settings were recommended for the first
four lots of OMAP5 ES1.0 silicon. These are not applicable
for OMAP5 ES2.0 and DRA7 silicon. So removing these EFUSE settings.

Reported-by: Griffis, Brad <bgriffis@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-04 08:12:38 -05:00
Roger Quadros
5afded6a4c ARM: DRA7xx: Add PRCM and Control information for SATA
Adds the necessary PRCM and Control register information for
SATA on DRA7xx.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
Roger Quadros
a087a7fb92 ARM: OMAP5: Add SATA platform glue
Add platform glue logic for the SATA controller.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
Roger Quadros
8ffcf74bb0 ARM: OMAP5: Add PRCM and Control information for SATA
Adds the necessary PRCM and Control register information for
SATA on OMAP5.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
Roger Quadros
9c4b64fb61 ARM: OMAP5: Add Pipe3 PHY driver
Pipe3 PHY is used by SATA, USB3 and PCIe modules. This is
a driver for the Pipe3 PHY.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:08 -05:00
SRICHARAN R
54d022e76c ARM: DRA7/OMAP5: EMIF: Add workaround for bug 0039
When core power domain hits oswr, then DDR3 memories does not come back
while resuming. This is because when EMIF registers are lost, then the
controller takes care of copying the values from the shadow registers.
If the shadow registers are not updated with the right values, then this
results in incorrect settings while resuming. So updating the shadow registers
with the corresponding status registers here during the boot.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-12-04 08:12:08 -05:00
SRICHARAN R
6c70935d75 ARM: DRA: EMIF: Change DDR3 settings to use hw leveling
Currently the DDR3 memory on DRA7 ES1.0 evm board is enabled using
software leveling. This was done since hardware leveling was not
working. Now that the right sequence to do hw leveling is identified,
use it. This is required for EMIF clockdomain to idle and come back
during lowpower usecases.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-12-04 08:12:08 -05:00
Tom Rini
39245c8699 am33xx: Stop modifying certain EMIF4D registers
Based on the definitive guide to EMIF configuration[1] certain registers
that we have been modifying (and are documented registers) should be
left in their reset values rather than modified.  This has been tested
on AM335x GP EVM and Beaglebone White.

[1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
2013-12-04 08:11:45 -05:00
Lubomir Popov
87b94a43d6 ARM: OMAP4: Fix bug in omap4470_volts struct
The struct incorrectly referenced SMPS1 for all three power
domains. Fixed this by using SMPS2 and SMPS5 as appropriate.

Add some comments and choose voltage values that correspond
to voltage selection codes.

Signed-off-by: Lubomir Popov <l-popov@ti.com>
2013-12-04 08:11:28 -05:00
Chin Liang See
4c54419737 socfpga: Adding Freeze Controller driver
Adding Freeze Controller driver. All HPS IOs need to be
in freeze state during pin mux or IO buffer configuration.
It is to avoid any glitch which might happen
during the configuration from propagating to external devices.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-03 14:38:56 +01:00
Rajeshwari Shinde
347e45d745 exynos: spl: Add a custom spi copy function
This patch implements a custom spi_copy funtion to copy u-boot from SF
to RAM. This is faster then iROM spi_copy funtion as this runs spi at
50Mhz and also in WORD mode of operation.

Changed a printf in pinmux.c to debug just to avoid the compilation
error in SPL.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-03 15:26:33 +09:00
Nobuhiro Iwamatsu
cae83ce515 arm: rmobile: Remove config.mk
Renesas ARM SoCs (R-Mobile, R-Car) are armv7 only.
This drops armv5 supprt from PLATFORM_CPPFLAGS and remove config.mk of
rmobile.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-12-03 09:47:15 +09:00
Nobuhiro Iwamatsu
7579751c14 arm: kzm9g: Fix undefined reference to `__aeabi_uldivmod' error
The kzm9g board fails in building with -march=armv7-a.
This fixs this problem by converting to do_div().

-----
USE_PRIVATE_LIBGCC=yes ./MAKEALL kzm9g
...
arch/arm/cpu/armv7/rmobile/librmobile.o: In function `get_time_us':
arch/arm/cpu/armv7/rmobile/timer.c:41: undefined reference to `__aeabi_uldivmod'
arch/arm/cpu/armv7/rmobile/librmobile.o: In function `get_time_ms':
arch/arm/cpu/armv7/rmobile/timer.c:47: undefined reference to `__aeabi_uldivmod'
-----

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
2013-12-03 09:47:08 +09:00
Nobuhiro Iwamatsu
bd0550fc5f arm: rmobile: Add support R8A7791
Renesas R8A7791 is CPU with Cortex-A15.
This supports the basic register definition and GPIO and
framework of PFC.

Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-03 09:46:45 +09:00
Nobuhiro Iwamatsu
1d0e92782f arm: rmobile: Add support R8A7790
Renesas R8A7790 is CPU with Cortex-A7 and A15.
This supports the basic register definition and GPIO and
framework of PFC.

Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-03 09:45:20 +09:00
Nobuhiro Iwamatsu
941b5a40a5 arm: rmobile: Move lowlevel_init.o to taget of each CPU
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2013-12-03 09:42:28 +09:00
Jaehoon Chung
a85ca22f62 arm: exynos: fix set_mmc_clk for exynos4x12
Fix the set_mmc_clk() for exnos4x12.
If board is exynos4x12, mmc clock should be set to wrong value.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-03 09:39:46 +09:00
Albert ARIBAUD
77524d2c9d Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master' 2013-12-02 16:00:10 +01:00
Heiko Schocher
4535a24c0c arm926ejs, at91: add common phy_reset function
add common phy reset code into a common function.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Jens Scharsig <esw@bus-elektronik.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Markus Hubig <mhubig@imko.de>
Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01 22:38:52 +01:00
Bo Shen
c5e8885aab arm: atmel: sama5d3: spl boot from fat fs SD card
Enable Atmel sama5d3xek boart spl boot support, which can load u-boot
from SD card with FAT file system.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01 22:38:51 +01:00
Bo Shen
9d9289cb31 arm: atmel: add ddr2 initialization function
The MPDDRC supports different type of SDRAM
This patch add ddr2 initialization function

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01 22:38:47 +01:00
Bo Shen
184c551b85 arm: atmel: sama5d3: correct the ID for DBGU and PIT
As the DBGU and PIT has its own ID on sama5d3 SoC, while not share
with SYS ID. So, correct them.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01 22:38:39 +01:00
Tom Rini
faca8ff55f Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2013-11-25 10:42:13 -05:00
Albert ARIBAUD
d44a5f5128 Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master' 2013-11-22 10:19:35 +01:00
pekon gupta
2c17e6d1d9 am335x: fix GPMC config for NAND and NOR SPL boot
GPMC controller is common IP to interface with both NAND and NOR flash devices.
Also, it supports max 8 chip-selects, which can be independently connected to
any of the devices.
But ROM code expects the boot-device to be connected to only chip-select[0].
Thus to resolve conflict between NOR and NAND boot. This patch:
- combines NOR and NAND configs spread in board files to common gpmc_init()
- configures GPMC based on boot-mode selected for SPL boot.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
pekon gupta
beba5f04f2 mtd: nand: omap: make am33xx/elm.c as common driver for all OMAPx and AMxxxx platforms
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
	and include in all board configs using AM33xx SoC platform.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
Masahiro Yamada
a52f90f074 arm: rmobile: Do not create a symbolic link to sh timer
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-11-17 14:11:33 -05:00
Tom Rini
5e995c00f6 TI:omap: Update u-boot-spl.lds for i2c multibus/multiadapter update
In 6789e84 we update u-boot-spl.lds for OMAP to ensure we include
adapter information, as we use i2c during SPL.  However, the regex used
also means we included commands that may have been built.  On omap5_uevm
this leads to a failure as we include the command from the do_tca642x
command, and fail to link.  The fix is to restrict our regex to only the
i2c list parts.

Signed-off-by: Tom Rini <trini@ti.com>
2013-11-15 12:20:33 -05:00
Wu, Josh
618bbbb2e9 ARM: at91: sama5d3: add support for sama5d36 chip
The SAMA5D36 chip is the superset product of SAMA5D3x family.

For detail information please refer to:
  http://www.atmel.com/Microsite/sama5d3/default.aspx

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-13 22:18:18 +01:00
Heiko Schocher
6789e84eca i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13 06:18:17 +01:00
Heiko Schocher
16678eb40f arm, am33x: make RTC32K OSC enable configurable
As
http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast
states:
"Initialize devices only when they are needed within U-Boot"

enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is
enabled. Enable this in ti_am335x_common.h, so all boards in mainline
should work as before.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-11-11 12:16:30 -05:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
Albert ARIBAUD
3285d4ca19 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-11-07 09:32:16 +01:00
Radhey Shyam Pandey
b5f05b0634 arm: zynq : Revert TZ_DDR_RAM to secure.
TZ_DDR_RAM on reset is in secure mode.
Since uboot and linux runs in full
TZ privilege secure mode, no need
to set DDR trustzone to non-secure.

Signed-off-by: Radhey Shyam Pandey <radheys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-11-06 09:24:06 +01:00
Michal Simek
c1824ea268 arm: zynq: Do not remap OCM to high address
In case where ps-ddr is not used, do not remap
OCM to high address and keep it from 0x0.
Linux SMP requires to have memory at 0x0.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-11-06 09:23:58 +01:00
Rob Herring
5b6da28352 ARM: versatile: convert to common timer code
Convert versatile to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:24:22 -05:00
Rob Herring
31df9893b9 ARM: tegra: convert to common timer code
Convert tegra to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:24:22 -05:00
Rob Herring
23ab7ee0ff ARM: socfpga: convert to common timer code
Convert socfpga to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:23:45 -05:00
Rob Herring
3dae5b510e ARM: mx25: convert to common timer code
Convert mx25 to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:09:34 -05:00
Rob Herring
9df1bd416d ARM: highbank: convert to common timer code
Convert highbank to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:08:10 -05:00
Tom Rini
6843918e00 am335x: Enable CONFIG_OMAP_WATCHDOG support
There is a board-specific portion for calling watchdog enable itself, in
main U-Boot.

Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01 15:55:59 -04:00
Tom Rini
155d424a9a am33xx, davinci: Create and use <asm/davinci_rtc.h>
Create a common header file for the RTC IP block that is shared between
davinci and am33xx.

Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01 15:30:22 -04:00
Masahiro Yamada
09ab61c660 ARM: s5pc, exynos: move Samsung ARM SoC specific code under arch/arm/
This patch moves S5PC, EXYNOS specific directory entries
from the toplevel Makefile to arch/arm/cpu/armv7/Makefile
using Kbuild descending feature.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
2013-10-31 13:26:44 -04:00
Masahiro Yamada
3c5edd8ca5 ARM: omap: move OMAP specific code under arch/arm/
This patch moves OMAP specific directory entries
from the toplevel Makefile and spl/Makefile
to arch/arm/cpu/armv7/Makefile using Kbuild descending feature.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
2013-10-31 13:26:44 -04:00
Masahiro Yamada
37d82beb57 ARM: tegra: move Tegra specific code under arch/arm/
This patch moves Tegra specific directory entries
from the toplevel Makefile and spl/Makefile
to arch/arm/cpu/*/Makefile using Kbuild descending feature.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <TWarren@nvidia.com>
2013-10-31 13:26:44 -04:00
Marek Vasut
a0f9761075 ARM: mxs: Enable DCDC converter for battery boot
In case the board detected sufficient voltage for battery boot,
make sure the DCDC converter is ON and the board is not running
only from linregs, otherwise an instability will be observed.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2013-10-31 17:54:23 +01:00
Fabio Estevam
357efe69e9 mx5: lowlevel_init: Remove unused macro
setup_wdog macro is not used anywhere, so just remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-10-31 17:54:03 +01:00
Fabio Estevam
4867b634b7 ARM: mx5: Enable L2 cache
Enable L2 cache for improving the system performance.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-10-31 17:54:03 +01:00
Masahiro Yamada
fa8f95084d ARM: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Masahiro Yamada
3d9c84737b arm720t: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Masahiro Yamada
833db7405a arm920t: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Masahiro Yamada
d8769c62c1 arm926ejs: convert makefiles to Kbuild style
Note1:
In arch/arm/cpu/arm926ejs/spear/Makefile
START := start.o
was changed
extra-$(CONFIG_SPL_BUILD) := start.o
because spear/start.o is only used for SPL.

Note2:
START := start.o
was missing from arch/arm/cpu/arm926ejs/mxs/Makefile.
This commit simply adds
extra-$(CONFIG_SPL_BUILD) := start.o

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Masahiro Yamada
4e1aa8437a armv7: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Tom Rini
748bde608a Merge branch 'master' of git://git.denx.de/u-boot-usb 2013-10-21 08:10:36 -04:00
Dan Murphy
834e91af43 usb: dra7xx: Add support for dra7xx xhci USB host
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Dan Murphy
d861a333da ARM: OMAP5: Add registers and defines for USBOTG SS
Add the prcm registers and the bit definitions to enable the
USB SS port of the OMAP5 device.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:39 +02:00
Vivek Gautam
80c4c5964f arm: exynos: Add methods to control power to USB 3.0 PHY
Adding methods to turn on/off power to USB3.0 type PHY
as and when required by the controller.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
2013-10-20 23:42:38 +02:00
Marek Vasut
77b0e2239a ARM: mxs: Setup stack in JTAG mode
In case the MX23/MX28 is switched into JTAG mode via the BootMode select
switches, the BootROM bypasses the CPU core registers initialization.
This in turn means that the Stack Pointer (SP) register is not set as
it is in every other mode of operation, but instead is only zeroed out.

To prevent U-Boot SPL from crashing in this obscure JTAG mode, configure
the SP to point at the CONFIG_SYS_INIT_SP_ADDR if the SP is zeroed out.

Note that in case the SP is already configured, we must preserve that exact
SP value and must not modify it. This is important since in every other mode
but the JTAG mode, the SPL returns into the BootROM and BootROM in turn loads
U-Boot itself. If the SP were to be corrupted, the BootROM won't be able to
continue it's operation after returned from SPL and the system would crash.

Finally, add the JTAG mode switch identifier, so it's not recognised as
Unknown mode.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
2013-10-17 09:44:20 +02:00
Marek Vasut
6654f33c9b ARM: mxs: tools: Use mkimage for BootStream generation
Now that mkimage can generate an BootStream for i.MX23 and i.MX28,
use the mkimage as a default tool to generate the BootStreams instead
of the elftosb tool. This cuts out another obscure dependency.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-10-17 09:44:20 +02:00
Pierre Aubert
762a88ccf8 mx6: compute PLL PFD frequencies rather than using defines
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
2013-10-17 09:44:20 +02:00
Michal Simek
262f08d6ea zynq: Use arch_cpu_init() instead of lowlevel_init()
Zynq lowlevel_init() was implemented in C but stack
pointer is setup after function call in _main().
Move architecture setup to arch_cpu_init() which is call
as the first function in board_init_f() which
already have correct stack pointer.

Reported-by: Sven Schwermer <sven.schwermer@tuhh.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-10-17 08:34:45 +02:00
trem
fac9640895 i2c: mxc: move to new subsystem
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
2013-10-17 07:20:24 +02:00
Wolfgang Denk
16641d52fc Coding Style cleanup: drop some excessive empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:54 -04:00
Wolfgang Denk
d4c8aa9cb4 Coding Style cleanup: remove trailing empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:54 -04:00
Wolfgang Denk
93e1459641 Coding Style cleanup: replace leading SPACEs by TABs
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Drop changes for PEP 4 following python tools]
Signed-off-by: Tom Rini <trini@ti.com>
2013-10-14 16:06:54 -04:00
Wolfgang Denk
3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00
Dan Murphy
47a4bea6af ARM: omap4: Update sdram setting for panda rev A6
OMAP4 panda rev A6 is a 4430 es2.3 IC with an updated memory
part.

The panda rev A6 uses Elpida 2x4Gb memory and no longer uses Micron
so the timings needs to be updated

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-14 16:06:52 -04:00
Tom Rini
9f3fe6da27 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-10-08 09:51:48 -04:00
Tom Rini
968294bd7b Merge branch 'master' of git://git.denx.de/u-boot-spi 2013-10-08 09:03:15 -04:00
Chin Liang See
5d649d2b08 socfpga: Adding System Manager driver
Adding System Manager driver which will configure the
pin mux for real hardware Cyclone V development kit
(not Virtual Platform)

Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2013-10-07 19:32:21 +02:00
Albert ARIBAUD
0610a16cf2 omap1510inn: arm925t: remove support
omap1510inn is orphan and has been for years now.
Reove it and, as it was the only arm925t target,
also remove arm925t support.
Update doc/README.scrapyard accordingly.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-10-07 19:25:19 +02:00
Poddar, Sourav
62d206dc31 armv7: hw_data: change clock divider setting.
Clock requirement for qspi clk is 192 Mhz.
According to the below formulae,

f dpll = f ref * 2 * m /(n + 1)
clockoutx2_Hmn = f dpll / (hmn+ 1)

fref = 20 Mhz, m = 96, n = 4 gives f dpll = 768 Mhz
For clockoutx2_Hmn to be 768, hmn + 1 should be 4.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-07 17:55:51 +05:30
Matt Porter
c97a9b3275 omap5: add qspi support
Add QSPI definitions and clock configuration support.

Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-07 17:55:50 +05:30
Andre Przywara
f833e790b4 ARM: virtualization: replace verbose license with SPDX identifier
The original creation of arch/arm/cpu/armv7/{virt-v7.c,nonsec_virt.S}
predates the SPDX conversion, so the original elaborate license
statements sneaked in.
Fix this by replacing them with the proper abbreviation.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-07 08:21:13 -04:00
Tom Rini
f835c77fb7 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-10-04 13:17:48 -04:00
Andre Przywara
d429688754 ARM: extend non-secure switch to also go into HYP mode
For the KVM and XEN hypervisors to be usable, we need to enter the
kernel in HYP mode. Now that we already are in non-secure state,
HYP mode switching is within short reach.

While doing the non-secure switch, we have to enable the HVC
instruction and setup the HYP mode HVBAR (while still secure).

The actual switch is done by dropping back from a HYP mode handler
without actually leaving HYP mode, so we introduce a new handler
routine in our new secure exception vector table.

In the assembly switching routine we save and restore the banked LR
and SP registers around the hypercall to do the actual HYP mode
switch.

The C routine first checks whether we are in HYP mode already and
also whether the virtualization extensions are available. It also
checks whether the HYP mode switch was finally successful.
The bootm command part only calls the new function after the
non-secure switch.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-03 21:28:55 +02:00
Andre Przywara
ba6a169811 ARM: add SMP support for non-secure switch
Currently the non-secure switch is only done for the boot processor.
To enable full SMP support, we have to switch all secondary cores
into non-secure state also.

So we add an entry point for secondary CPUs coming out of low-power
state and make sure we put them into WFI again after having switched
to non-secure state.
For this we acknowledge and EOI the wake-up IPI, then go into WFI.
Once being kicked out of it later, we sanity check that the start
address has actually been changed (since another attempt to switch
to non-secure would block the core) and jump to the new address.

The actual CPU kick is done by sending an inter-processor interrupt
via the GIC to all CPU interfaces except the requesting processor.
The secondary cores will then setup their respective GIC CPU
interface.
While this approach is pretty universal across several ARMv7 boards,
we make this function weak in case someone needs to tweak this for
a specific board.

The way of setting the secondary's start address is board specific,
but mostly different only in the actual SMP pen address, so we also
provide a weak default implementation and just depend on the proper
address to be set in the config file.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-03 21:28:51 +02:00
Andre Przywara
1ef923851a ARM: add C function to switch to non-secure state
The core specific part of the work is done in the assembly routine
in nonsec_virt.S, introduced with the previous patch, but for the full
glory we need to setup the GIC distributor interface once for the
whole system, which is done in C here.
The routine is placed in arch/arm/cpu/armv7 to allow easy access from
other ARMv7 boards.

We check the availability of the security extensions first.

Since we need a safe way to access the GIC, we use the PERIPHBASE
registers on Cortex-A15 and A7 CPUs and do some sanity checks.
Boards not implementing the CBAR can override this value via a
configuration file variable.

Then we actually do the GIC enablement:
a) enable the GIC distributor, both for non-secure and secure state
   (GICD_CTLR[1:0] = 11b)
b) allow all interrupts to be handled from non-secure state
   (GICD_IGROUPRn = 0xFFFFFFFF)

The core specific GIC setup is then done in the assembly routine.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-03 21:28:43 +02:00
Andre Przywara
16212b594f ARM: add assembly routine to switch to non-secure state
While actually switching to non-secure state is one thing, another
part of this process is to make sure that we still have full access
to the interrupt controller (GIC).
The GIC is fully aware of secure vs. non-secure state, some
registers are banked, others may be configured to be accessible from
secure state only.
To be as generic as possible, we get the GIC memory mapped address
based on the PERIPHBASE value in the CBAR register. Since this
register is not architecturally defined, we check the MIDR before to
be from an A15 or A7.
For CPUs not having the CBAR or boards with wrong information herein
we allow providing the base address as a configuration variable.

Now that we know the GIC address, we:
a) allow private interrupts to be delivered to the core
   (GICD_IGROUPR0 = 0xFFFFFFFF)
b) enable the CPU interface (GICC_CTLR[0] = 1)
c) set the priority filter to allow non-secure interrupts
   (GICC_PMR = 0xFF)

Also we allow access to all coprocessor interfaces from non-secure
state by writing the appropriate bits in the NSACR register.

The generic timer base frequency register is only accessible from
secure state, so we have to program it now. Actually this should be
done from primary firmware before, but some boards seems to omit
this, so if needed we do this here with a board specific value.
The Versatile Express board does not need this, so we remove the
frequency from the configuration file here.

After having switched to non-secure state, we also enable the
non-secure GIC CPU interface, since this register is banked.

Since we need to call this routine also directly from the smp_pen
later (where we don't have any stack), we can only use caller saved
registers r0-r3 and r12 to not mess with the compiler.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-03 21:28:25 +02:00
Andre Przywara
45b940d6f9 ARM: add secure monitor handler to switch to non-secure state
A prerequisite for using virtualization is to be in HYP mode, which
requires the CPU to be in non-secure state first.
Add a new file in arch/arm/cpu/armv7 to hold a monitor handler routine
which switches the CPU to non-secure state by setting the NS and
associated bits.
According to the ARM architecture reference manual this should not be
done in SVC mode, so we have to setup a SMC handler for this.
We create a new vector table to avoid interference with other boards.
The MVBAR register will be programmed later just before the smc call.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-03 21:27:11 +02:00
Tom Rini
6297872cd5 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-10-02 11:45:22 -04:00
Albert ARIBAUD
f04c537629 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-10-02 14:53:27 +02:00
Albert ARIBAUD
5c8d5b6fc1 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-10-02 08:10:36 +02:00
Pierre Aubert
a0a0dacfe8 mx6: Fix use of improper value in enable_ipu_clock
The value MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET that was used to initialize
the CCGR3 register caused an undefined value for CG0.

Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-09-27 13:53:35 +02:00
Bo Shen
3668ce3c80 ARM: atmel: add RNDIS gadget support
Add RNDIS gadget support to test atmel usba udc driver

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-09-24 17:51:35 +02:00
Dani Krishna Mohan
3dd22a37aa ARM: Added I2S0 clocks for audio
This patch makes the necessary changes for making use of
I2S0 channel instead of I2S1 channel on smdk board. This
changes are done to maintain the uniformity to use I2S0 channel.

Signed-off-by: Dani Krishna Mohan <krishna.md@samsung.com>
2013-09-24 09:10:33 -04:00
Jeroen Hofstee
fe1378a961 ARM: use r9 for gd
To be more EABI compliant and as a preparation for building
with clang, use the platform-specific r9 register for gd
instead of r8.

note: The FIQ is not updated since it is not used in u-boot,
and under discussion for the time being.

The following checkpatch warning is ignored:
WARNING: Use of volatile is usually wrong: see
Documentation/volatile-considered-harmful.txt

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-09-23 18:00:02 +02:00
Masahiro Yamada
3102274d8b ARM: refactor compiler options in config.mk
Every ARM cpu config.mk (arch/arm/cpu/{CPUDIR}/config.mk) defines:

PLATFORM_RELFLAGS += -fno-common -ffixed-r8 -msoft-float

So, this patch moves the common compiler options to arch/arm/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-09-23 17:03:05 +02:00
Michal Simek
7ba69b7dcc arm: zynq: Fix timer loadaddress
Reload address was written to the counter register
instead of load register.
The problem happens when timer expires but never
reload to ~0UL (it is downcount timer).

Reported-by: Stephen MacMahon <stephenm@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-09-23 16:26:32 +02:00
Lokesh Vutla
e22cc0cf13 ARM: OMAP5: Avoid writing into LDO SRAM bits
Writing magic bits into LDO SRAM was suggested only for OMAP5432
ES1.0. Now these are no longer applicable. Moreover these bits should
not be overwritten as they are loaded from EFUSE. So avoid
writing into these registers.

Boot tested on OMAP5432 ES2.0

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-09-20 16:57:40 -04:00
Steve Kipisz
52f7d8442e am335x:Handle worst case scenario for Errata 1.0.24
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset,
the boot ROM sets the frequencies for OPP100. This patch attempts to
drop the frequencies back to OPP50 as soon as possible in the SPL. Then
later the voltages and frequencies up set higher.

Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Adapt to current framework]
Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 16:57:40 -04:00
Tom Rini
9721027aae am335x_evm: am33xx_spl_board_init function and scale core frequency
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on.  In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed.  In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz.  In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1.  As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe.  In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.

Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 16:57:35 -04:00
Fabio Estevam
31f07964c8 mx6slevk: Add Ethernet support
mx6slevk has a SMSC8720 connected in RMII mode.

Add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20 17:55:37 +02:00
Tom Rini
6a0d803c7c am33xx: Add am33xx_spl_board_init function, call
We need to allow for a further call-out in spl_board_init.  Call this
am33xx_spl_board_init and add a __weak version.  This function may be
used to scale the MPU frequency up, depending on board needs.

Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 11:01:26 -04:00
Robert P. J. Day
1bce2aeb6f Cosmetic: Fix a number of typos, no functional changes.
Fix various misspellings of things like "environment", "kernel",
"default" and "volatile", and throw in a couple grammar fixes.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-09-20 10:30:54 -04:00
Masahiro Yamada
aeef2b090d ARM: s3c44b0: remove remainders of dead board
Because commit 5dc5f36 removed B2 board support,
arch/arm/cpu/s3c44b0/* and arch/arm/include/asm/arch-s3c44b0/*
are not necessary anymore.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
2013-09-19 08:59:49 +02:00
trem
e24278aff2 mx27: add missing constant for mx27
Add some missing constant (chip select, ...)

Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-09-10 19:12:55 +02:00
Marek Vasut
7b8657e2bd ARM: mxs: Receive r0 and r1 passed from BootROM
Make sure value in register r0 and r1 is preserved and passed to
the board_init_ll() and mxs_common_spl_init() where it can be
processed further. The value in r0 can be configured during the
BootStream generation to arbitary value, r1 contains pointer to
return value from CALL'd function.

This patch also clears the value in r0 before returning to BootROM
to make sure the BootROM is not confused by this value.

Finally, this patch cleans up some comments in the start.S file.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-09-10 19:12:54 +02:00
Marek Vasut
d4c9135c96 ARM: mxs: Document the power block initialization
This patch adds documentation for the functions used during the
initialization of MXS power block.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-09-10 19:12:54 +02:00
Andrew Gabbasov
d55e0dabd7 mx6: Fix calculation of emi_slow clock rate
This is porting of Freescale's patch from version imx_v2009.08_3.0.35_4.0.0,
that fixes the obvious mistype of bits offset macro name (ACLK_EMI_PODF_OFFSET
was used instead of ACLK_EMI_SLOW_PODF_OFFSET).

Using the occasion, change the variable name 'emi_slow_pof' to more consistent
'emi_slow_podf'.

Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2013-09-10 18:22:27 +02:00
Chin Liang See
68e1747f9c socfpga: Creating driver for Reset Manager
Consolidating reset code into reset_manager.c. Also
separating reset configuration for virtual target and
real hardware Cyclone V development kit

Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2013-09-06 12:09:06 +02:00
Michal Simek
fba1ed422e arm: lds: Remove libgcc eabi exception handling tables
Remove ARM eabi exception handling tables (for frame unwinding).
AFAICT, u-boot stubs away the frame unwiding routines, so the tables will
more or less just consume space. It should be OK to remove them.

Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-09-05 13:41:42 +02:00
Albert ARIBAUD
19d829fa60 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Conflicts:
	drivers/serial/serial.c

The conflict above was a trivial case of adding one init
function in each branch, and manually resolved in merge.
2013-09-05 11:15:26 +02:00
Albert ARIBAUD
e62d5fb0da Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-09-04 14:06:56 +02:00
Albert ARIBAUD
4eef93da26 Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master' 2013-09-04 11:50:25 +02:00
Albert ARIBAUD
6d4511b2c6 Merge 'u-boot-microblaze/zynq' into (u-boot-arm/master'
Conflicts:
	arch/arm/include/asm/arch-zynq/hardware.h

The conflict above was trivial and solved during merge.
2013-09-03 14:01:02 +02:00
Eric Nelson
8467faef7f i.MX6: Set and clear the gating bits for Phase Fractional Dividers
This addresses silicon errata ERR006282 as described in this
document:
	https://community.freescale.com/docs/DOC-94581

Also implemented in Freescale's 2009.08-based release:

	http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/
	Commit id: b7c5badf94ffbe6cd0845efbb75e16e05e3af404

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-08-31 18:09:37 +02:00
Hector Palacios
6f6059e0f1 ARM: mxs: rename function that sets AUTO_RESTART flag
The AUTO_RESTART flag of HW_RTC_PERSISTENT0 register will
power up the chip automatically 180ms after power down.
This bit must be enabled by the boot loader to ensure the
target can start upon hardware reset or watchdog reset
even when powered from a battery.

Currently the function named 'mxs_power_clear_auto_restart()'
is setting this flag although the 'clear' in its name suggest
the opposite.

This patch renames the function to 'mxs_power_set_auto_restart()'
and removes the comment about EVK revision A which was confusing
because the function indeed was setting the flag.

Signed-off-by: Hector Palacios <hector.palacios@digi.com>
2013-08-31 17:50:38 +02:00
Marek Vasut
bce8837071 ARM: mxs: tools: Add mkimage support for MXS bootstream
Add mkimage support for generating and verifying MXS bootstream.
The implementation here is mostly a glue code between MXSSB v0.4
and mkimage, but the long-term goal is to rectify this and merge
MXSSB with mkimage more tightly. Once this code is properly in
U-Boot, MXSSB shall be deprecated in favor of mkimage-mxsimage
support.

Note that the mxsimage generator needs libcrypto from OpenSSL, I
therefore enabled the libcrypto/libssl unconditionally.

MXSSB: http://git.denx.de/?p=mxssb.git;a=summary

The code is based on research presented at:
http://www.rockbox.org/wiki/SbFileFormat

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
2013-08-31 15:26:52 +02:00
Stefano Babic
b83c709e8d imx: add status reporting for HAB status
Add functions to report the HAB (High Assurance Boot) status
of e.g. i.MX6 CPUs.

This is taken from

git://git.freescale.com/imx/uboot-imx.git branch imx_v2009.08_3.0.35_4.0.0
cpu/arm_cortexa8/mx6/generic.c
include/asm-arm/arch-mx6/mx6_secure.h

Signed-off-by: Stefano Babic <sbabic@denx.de>
2013-08-31 15:06:29 +02:00
Albert ARIBAUD
8d20836615 arm: omap3: fix SRAM copy and execution sequence
Fix size calculation in copy of go_to_speed into SRAM.
Use SRAM_CLK_CODE in call to SRAM-based go_to_speed.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-08-28 11:44:58 -04:00
Lubomir Popov
81aee9723d ARM: OMAP4470: Add Elpida EDB8164B3PF memory configuration
OMAP4470 SDP SoM has EDB8164B3PF PoP memory on board.
This memory has 4Gb x 2CS = 8Gb configuration.
Add configuration for runtime calculation and precalculated cases.

Patch is based on a draft Lubomir's patch [1].

[1] http://lists.denx.de/pipermail/u-boot/2013-April/150851.html

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
[taras@ti.com: cleaned up patch and fixed precalculated values]
Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28 11:44:58 -04:00
Taras Kondratiuk
40aadf9201 ARM: OMAP4470: Add voltage and dpll data
OMAP4470 reference design uses TWL6032 PMIC
with a following connection scheme:
  VDD_CORE = TWL6032 SMPS2
  VDD_MPU  = TWL6032 SMPS1
  VDD_IVA  = TWL6032 SMPS5

Set voltage and frequency values according to
OMAP4470 Data Manual Operating Condition Addendum v0.7

Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28 11:44:58 -04:00
Taras Kondratiuk
696f81f9a9 ARM: OMAP4470: Add OMAP4470 identification
Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28 11:44:58 -04:00
Fabio Estevam
76b6b19614 usb: ehci-mx5: Use 'bool' instead of 'unsigned char'
The 'enable' argument can be better expressed as boolean.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2013-08-26 21:56:34 +02:00
Bo Shen
e08d6f3aaf arm: atmel: add gmac support for sama5d3xek board
add gmac support for sama5d3xek board, the gmac embedded in:
  - sama5d33, sama5d34, sama5d35

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22 16:49:54 +02:00
Tom Rini
e20cc2ca15 Merge branch 'master' of git://88.191.163.10/u-boot-arm
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.

Conflicts:
	arch/arm/include/asm/arch-am33xx/hardware.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-18 14:14:34 -04:00
Albert ARIBAUD
9ed887caec Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-08-17 18:24:13 +02:00
TENART Antoine
dcf846d5da Add TI816X support
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Fix warnings about vtp things in emif4.c, adapt AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:37 -04:00
TENART Antoine
9ed6e41239 Prepare for TI816X : reuse existing code from TI814X
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX

Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:37 -04:00
Heiko Schocher
9c8deaeeb7 arm, da850: enable the correct uart in arch_cpu_init()
in arch_cpu_init() uart2 is fix enabled, without reference the
setting from CONFIG_SYS_NS16550_COM1. Use the setting from
CONFIG_SYS_NS16550_COM1 for enabling the console.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
2013-08-15 18:38:36 -04:00
Heiko Schocher
78056717e3 arm/davinci/da850: add uart0_pins_rtscts and RMII_MHz_50_CLK in emac_pins_rmii pinmux
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-08-15 18:38:36 -04:00
Taras Kondratiuk
0474fb0e2b omap: emif: Set initial DDR PHY config first
Commit "OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon"
(f40107345c)
changed sequence to set final DDR PHY config register value at the beginning.
Looks like it was made by mistake and should be reverted.

Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-15 18:38:35 -04:00
Masahiro Yamada
2f6af82719 ARM: omap24xx: remove remainders of dead board
Since Commit 7f5eef9 removed OMAP2420H4 support,
arm1136/omap24xx has not been used at all.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-15 18:38:33 -04:00
Naumann Andreas
a704a6d615 ARM: omap3: Implement dpll5 (HSUSB clk) workaround for OMAP36xx/AM/DM37xx according to errata sprz318e.
In chapter 'Advisory 2.1 USB Host Clock Drift Causes USB Spec Non-compliance in Certain Configurations' of the TI Errata it is recommended to use certain div/mult values for the DPLL5 clock setup.
So far u-boot used the old 34xx values, so I added the errata recommended values specificly for 36xx init only.
Also, the FSEL registers exist no longer, so removed them from init.

Tested this on a AM3703 board with 19.2MHz oscillator, which previously couldnt lock the dpll5 (kernel complained). As a consequence the EHCI USB port wasnt usable in U-Boot and kernel. With this patch, kernel panics disappear and USB working fine in u-boot and kernel.

Signed-off-by: Andreas Naumann <anaumann@ultratronik.de>
[trini: Add extern to <asm/arch-omap3/clock.h>
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 09:09:29 -04:00
Lokesh Vutla
571804086f ARM: AM43xx: Add build support
Add AM43xx support in the required places

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
806d279247 ARM: OMAP: Add CONFIG_OMAP_COMMON
Adding a new CONFIG_OMAP_COMMON which is included by all boards
that needs to build cpu/armv7/omap-common folder.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
3b34ac13fe ARM: AM43xx: clocks: Add dpll and clock data
Add dpll and clock data for AM43xx

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Heiko Schocher
0660481a59 ARM: AM33xx: Move s_init to a common place
s_init has the same outline for all the AM33xx based
board. So making it generic.
This also helps in addition of new Soc with minimal changes.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
95cb69faeb ARM: AM33xx: Cleanup clocks layer
Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
94d77fb656 ARM: AM33xx: Cleanup dplls data
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.

This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Michal Simek
39523bef29 zynq: slcr: Wait 100ms till clk is properly setup
If you don't wait you will loose the first sent packet
even all bits in emacps are correctly setup.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2013-08-12 08:59:55 +02:00
Michal Simek
148ba55cc6 zynq: Add new ddrc driver for ECC support
The first 1MB is not initialized by first stage bootloader.
Check if memory is setup to 16bit mode and ECC is enabled.
If it is, clear the first 1MB.
Also u-boot should report only the half size of memory.

Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-08-12 08:59:55 +02:00
Stephen Warren
065202803d config: don't define CONFIG_ARCH_DEVICE_TREE
Now that nothing uses CONFIG_ARCH_DEVICE_TREE, stop defining it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2013-08-02 18:30:11 -04:00
Stefano Babic
326ea986ac Merge git://git.denx.de/u-boot-arm
Conflicts:
	board/freescale/mx6qsabrelite/Makefile
	board/freescale/mx6qsabrelite/mx6qsabrelite.c
	include/configs/mx6qsabrelite.h

Signed-off-by: Stefano Babic <sbabic@denx.de>
2013-07-31 11:30:38 +02:00
Steve Kipisz
c5c7a7c32d am335x_evm: Add support to boot from NOR.
NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on.  When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB.  We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.

We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Steve Kipisz
cd8845d7a4 am335x_evm: Add support for the NOR module on the memory cape
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Tom Rini
392bba4ad0 am33xx: Correct gpmc_cfg->irqstatus/enable
Based on our usage of the GPMC, either with NOR or NAND we do not need
to be setting the irqstatus or irqenable bits and should clear them like
we have historically.

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Pardeep Kumar Singla
5ea7f0e328 mx6: Factor out common HDMI setup code
Instead of duplicating HDMI setup code for every mx6 board, factor out the common code

Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
Acked-By: Eric Nelson <eric.nelson@boundarydevices.com>
2013-07-27 10:49:36 +02:00
Mugunthan V N
b1e26e3bfb ARM: DRA7xx: Add CPSW support to DRA7xx EVM
Adding support for CPSW Ethernet support found in DRA7xx EVM

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Mugunthan V N
f986d97208 ARM: DRA7xx: Enable GMAC clock control
Enabling CPSW module by enabling GMAC clock control

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Lokesh Vutla
65e9d56fb9 ARM: DRA7xx: Lock DPLL_GMAC
Locking DPLL_GMAC

[mugunthanvnm@ti.com:Configure only if CPSW is selected]

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Andreas Bießmann
c4ec281822 omap3/sys_info: fix printout of OMAP36XX L3 freqency
The OMAP36xx/OMAP37xx family uses L3 frequency of 200MHz instead of 165MHz
used by OMAP34xx/OMAP35xx.

Also fix checkpatch warning about alignment.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-07-26 16:39:10 -04:00
Stefan Roese
bf0e86606d arm: omap3: spl: Fix problem with 8bit NAND devices
Currently in OMAP3 SPL, the GPMC for NAND is configured for 16bit
access. This patch adds support for 8bit NAND devices as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-07-26 16:39:10 -04:00
Albert ARIBAUD
8b485ba12b Merge branch 'u-boot/master' into u-boot-arm/master 2013-07-25 17:57:46 +02:00
Rob Herring
0f7cf3803f ARM: highbank: avoid bss write in timer_init
The timer_init function is called before relocation and writes to bss data
were corrupting relocation data. Fix this by removing the call to
reset_timer_masked. The initial timer count should be 0 or near 0 anyway,
so initializing the variables are not needed.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25 08:15:44 +02:00
Rob Herring
714d1f5da5 ARM: highbank: set timer prescaler to 256
The 150MHz clock rate gives u-boot time functions problems and there's no
benefit to a fast clock, so lower the rate.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25 08:15:33 +02:00
Rob Herring
ec0e413f93 ARM: highbank: fix get_tbclk value to timer rate
get_tbclk should return the timer's frequency, not CONFIG_SYS_HZ.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25 08:15:25 +02:00
Tom Rini
c2120fbfbc Merge branch 'master' of git://git.denx.de/u-boot-i2c
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
	board/sandburst/common/ppc440gx_i2c.c
	board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:50:24 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Alison Wang
1221b3d74a vf610: Add I2C support for Vybrid VF610 platform
This patch adds I2C support for Vybrid VF610 platform and adds
I2C0 support to VF610TWR board.

Signed-off-by: Alison Wang <b18965@freescale.com>
2013-07-23 08:34:57 +02:00
Łukasz Majewski
f4eaf88e6d arm:exynos:fix: Fix clock calculation for Exynos4210 based targets.
Provide proper setting for the APLL fout frequency calculation for
Exynos4 based targets (especially Exynos4210 - Trats board).

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2013-07-16 09:20:16 -04:00
Tom Rini
fbbbc86e8e Merge branch 'master' of git://git.denx.de/u-boot-arm
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.

Conflicts:
	arch/arm/dts/exynos5250.dtsi

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-12 10:36:48 -04:00
Albert ARIBAUD
630aacb085 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2013-07-10 20:40:47 +02:00
Minkyu Kang
e161f60f4d arm: exynos: fix clock calculation
There are differnce with clock calcuation by cpu variations.
This patch will fix it according to user manual.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
2013-07-09 16:15:30 +09:00
Rajeshwari Shinde
643be9c07e EXYNOS: Move files from board/samsung to arch/arm
This patch performs the following:

1) Convert the assembly code for memory and clock initialization to C code.
2) Move the memory and clock init codes from board/samsung to arch/arm
3) Creat a common lowlevel_init file across Exynos4 and Exynos5. Converted
   the common lowlevel_init from assembly to C-code
4) Made spl_boot.c and tzpc_init.c common for both exynos4 and exynos5.
5) Enable CONFIG_SKIP_LOWLEVEL_INIT as stack pointer initialisation is already
   done in _main.
6) exynos-uboot-spl.lds made common across SMDKV310, Origen and SMDK5250.

TEST: Tested SD-MMC boot on SMDK5250 and Origen.
      Tested USB and SPI boot on SMDK5250
      Compile tested for SMDKV310.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-07-05 17:06:55 +09:00
Rajeshwari Shinde
198a40b9f6 EXYNOS4210: Configure GPIO for uart
This patch configures the gpio values for UART
on Origen and SMDKV310 using pinmux

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-07-05 17:06:55 +09:00
Rajeshwari Shinde
dc20fdd76a EXYNOS: Add API for power reset and exit wakeup
This patch adds APIs to get power reset status and exit the wakeup condition for
both exynos5 and exynos4

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-07-05 17:06:54 +09:00
Axel Lin
87bd05d78f ARM: OMAP: GPIO: Fix valid range and enable usage of all GPIOs on OMAP5
The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs.
These SoCs have different gpio count but currently omap_gpio driver uses hard
coded 192 which is wrong.

This patch fixes this issue by:
1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h.
2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5.

Thanks for Lubomir Popov to provide valuable comments to fix this issue.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Heiko Schocher <hs@denx.de>
2013-07-02 09:21:16 -04:00
Lokesh Vutla
e3f53104e2 ARM: OMAP4+: Fix MA detection during SDRAM_AUTO_DETECTION
During SDRAM_AUTO_DETECTION MA is not configured.
For Soc's > OMAP4460 MA is present. So populating
MA for the same.

Tested on OMAP4430 PANDA, OMAP4460 PANDA.

Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-07-02 09:21:16 -04:00
Albert ARIBAUD
e6c7f86f03 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-06-28 17:51:13 +02:00
trem
79713f0ad8 mx27: add i2c clock
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
2013-06-26 17:34:21 +02:00
trem
6247c4653b mx27: add function enable_caches
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
2013-06-26 17:34:21 +02:00
Simon Glass
ca35a0cdf2 exynos: Avoid function instrumentation for microsecond timer
For tracing to work it has to be able to access the microsecond timer
without causing a recursive call to the function entry/exit handlers.
Add attributes to the relevant functions to support this.

Signed-off-by: Simon Glass <sjg@chromium.org>

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-06-26 10:18:56 -04:00
Mike Dunn
84c617beb2 pxa: use -mcpu=xscale compiler option
Pass '-mcpu=xscale' to the compiler instead of march and mtune.  This will cause
gcc to define the __XSCALE__ macro.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-06-22 15:25:28 +02:00
Mike Dunn
097d86d098 pxa: turn icache off in cpu_init_crit()
The comment in the low-level initialization function cpu_init_crit() says that
the caches are being disabled, but (oddly) the icache is actually turned on.
This is probably not a good idea prior to relocating code, so this patch turns
it off.  Tested on the pxa270.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-06-22 15:25:28 +02:00
Albert ARIBAUD
47bd65ef05 arm: make __rel_dyn_{start, end} compiler-generated
This change is only done where needed: some linker
scripts may contain relocation symbols yet remain
unchanged.

__rel_dyn_start and __rel_dyn_end each requires
its own output section; putting them in relocation
sections changes their flags and breaks relocation.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 23:05:29 +02:00
Albert ARIBAUD
d026dec875 arm: make __image_copy_{start, end} compiler-generated
This change is only done where needed: some linker
scripts may contain __image_copy_{start,end} yet
remain unchanged.

Also, __image_copy_end needs its own section; putting
it in relocation sections changes their flags and makes
relocation break.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 23:05:05 +02:00
Albert ARIBAUD
09d81184e1 remove all references to .dynsym
Discard all .dynsym sections from linker scripts
Remove all __dynsym_start definitions from linker scripts
Remove all __dynsym_start references from the codebase

Note: this touches include/asm-generic/sections.h, which
is not ARM-specific, but actual uses of __dynsym_start
are only in ARM, so this patch can safely go through
the ARM repository.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 23:04:05 +02:00
Albert ARIBAUD
c2543a21df Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-06-19 23:58:01 +02:00
Albert ARIBAUD
69f14dc2fd Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'
Conflicts:
	spl/Makefile
2013-06-19 12:53:59 +02:00
Heiko Schocher
7ea7f689ca arm, am33xx: move uart soft reset code to common place
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-18 10:40:06 -04:00
Heiko Schocher
7b9c5d0bfd arm, am335x: make mpu pll config configurable
upcoming support for siemens boards switches mpu pll clk in board
code. So make this configurable.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-06-18 09:18:46 -04:00
Heiko Schocher
49f7836500 arm, am33xx: move rtc32k_enable() to common place
move rtc32k_enable() to common place so all am33xx boards can use it.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-06-18 09:12:38 -04:00
Amar
2b81c26b7c EXYNOS5: DWMMC: Initialise the local variable to avoid unwanted results.
This patch initialises the local variable 'shift' to zero.
The uninitialised local variable 'shift' had garbage value and was
resulting in unwnated results in the functions exynos5_get_mmc_clk()
and exynos4_get_mmc_clk().

Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13 17:35:14 +09:00
Sergey Yanovich
847e6693cc arm: pxa: config option for PXA270 turbo mode
PXA270 CPU has turbo mode. The mode is 2.5 times faster than the
default run mode. Activating the mode early significantly speeds
up boot process.

Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
2013-06-12 22:24:12 +02:00
Vishwanathrao Badarkhe, Manish
68cd4a4c9f arm: da830: moved pinmux configurations to the arch tree
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.

Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
2013-06-10 08:54:46 -04:00
Lubomir Popov
ee28edac43 OMAP5: Enable access to auxclk registers
auxclk0 and auxclk1 are utilized on some OMAP5 boards.
Define the infrastructure needed for accessing them
without using magic numbers.

Also remove unrelated TPS62361 defines from clocks.h

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
2013-06-10 08:54:46 -04:00
Tom Rini
7f5eef93af arm: Remove OMAP2420H4 and all omap24xx support
The omap2420H4 was the only mainline omap24xx board.  Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time.  Remove this board as there's not been interest in
it in U-Boot for quite a long time.

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-10 08:43:19 -04:00
Sricharan R
92b0482c17 ARM: DRA7xx: EMIF: Change settings required for EVM board
DRA7 EVM board has the below configuration. Adding the
settings for the same here.

   2Gb_1_35V_DDR3L part * 2 on EMIF1
   2Gb_1_35V_DDR3L part * 4 on EMIF2

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
97405d843e ARM: DRA7xx: clocks: Update PLL values
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-06-10 08:43:10 -04:00
Sricharan R
f9b814a8e9 ARM: DRA7xx: Correct the SYS_CLK to 20MHZ
The sys_clk on the dra evm board is 20MHZ.
Changing the configuration for the same.
And also moving V_SCLK, V_OSCK defines to
arch/clock.h for OMAP4+ boards.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
e9d6cd042d ARM: DRA7xx: Do not enable srcomp for DRA7xx Soc's
Slew rate compensation cells are not present for DRA7xx
Soc's. So return from function srcomp_enable() if soc is not
OMAP54xx.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Nishanth Menon
18c9d55ac6 ARM: OMAP5: DRA7xx: support class 0 optimized voltages
DRA752 now uses AVS Class 0 voltages which are voltages in efuse.

This means that we can now use the optimized voltages which are
stored as mV values in efuse and program PMIC accordingly.

This allows us to go with higher OPP as needed in the system without
the need for implementing complex AVS logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
3332b24421 ARM: DRA7xx: clocks: Fixing i2c_init for PMIC
In DRA7xx Soc's voltage scaling is done using GPI2C.
So i2c_init should happen before scaling. I2C driver
uses __udelay which needs timer to be initialized.
So moving timer_init just before voltage scaling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
63fc0c775c ARM: DRA7xx: power Add support for tps659038 PMIC
TPS659038 is the power IC used in DRA7XX boards.
Adding support for this and also adding pmic data
for DRA7XX boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
4ca94d8186 ARM: OMAP4+: pmic: Make generic bus init and write functions
Voltage scaling can be done in two ways:
-> Using SR I2C
-> Using GP I2C
In order to support both, have a function pointer in pmic_data
so that we can call as per our requirement.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
af1d002f89 ARM: OMAP2+: Rename asm/arch/clocks.h asm/arch/clock.h
To be consistent with other ARM platforms,
renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Sricharan R
bcdd8f72f3 ARM: OMAP5: clocks: Do not enable sgx clocks
SGX clocks should be enabled only for OMAP5 ES1.0.
So this can be removed.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
9239f5b625 ARM: OMAP4+: Cleanup header files
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lubomir Popov
e0a8c99e61 OMAP5: Fix bug in omap5_es1_prcm struct
The newly introduced function setup_warmreset_time(), called
from within prcm_init(), tries to write to the prm_rsttime
OMAP5 register. The struct member holding this register's
address is however initialized for OMAP5 ES2.0 only. On ES1.0
devices this uninitialized value causes a second (warm) reset
at startup.

Add .prm_rsttime address init to the ES1.0 struct.

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Tom Rini <trini@ti.com>
2013-06-10 08:43:09 -04:00
Andrii Tseglytskyi
e69c585d76 OMAP5: add ABB setup for MPU voltage domain
Patch adds a call of abb_setup() function, and proper registers
definitions needed for ABB setup sequence. ABB is initialized
for MPU voltage domain.

Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
2013-06-10 08:43:09 -04:00
Andrii Tseglytskyi
4d0df9c1e9 OMAP3+: introduce generic ABB support
Adaptive Body Biasing (ABB) modulates transistor bias voltages
dynamically in order to optimize switching speed versus leakage.
Adaptive Body-Bias ldos are present for some voltage domains
starting with OMAP3630. There are three modes of operation:

* Bypass - the default, it just follows the vdd voltage
* Foward Body-Bias - applies voltage bias to increase transistor
  performance at the cost of power.  Used to operate safely at high
  OPPs.
* Reverse Body-Bias - applies voltage bias to decrease leakage and
  save power.  Used to save power at lower OPPs.

Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
2013-06-10 08:43:09 -04:00
Albert ARIBAUD
10e167329b Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Conflicts:
	drivers/serial/Makefile
2013-06-08 14:35:10 +02:00
Tom Warren
dbc000bfb5 ARM: tegra: only enable SCU on Tegra20
The non-SPL build of U-Boot on Tegra only runs on a single CPU, and
hence there is no need to enable the SCU when running U-Boot. If an
SMP OS is booted, and it needs the SCU enabled, it will enable the SCU
itself. U-Boot doing so is redundant.

The one exception is Tegra20, where an enabled SCU is required for some
aspects of PCIe to work correctly.

Some Tegra SoCs contain CPUs without a software-controlled SCU. In this
case, attempting to turn it on actively causes problems. This is the case
for Tegra114. For example, when running Linux, the first (or at least
some very early) user-space process will trigger the following kernel
message:

Unhandled fault: imprecise external abort (0x406) at 0x00000000

This is typically accompanied by that process receving a fatal signal,
and exiting. Since this process is usually pid 1, this causes total
system boot failure.

Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, fleshed out description, ported to upstream chipid APIs]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-06-06 09:12:32 -07:00
Tom Rini
4596dcc1d4 am33xx/omap: Move save_omap_boot_params to omap-common/boot-common.c
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common.  Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx.  Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.

Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-05 08:46:49 -04:00
Tom Rini
0ac6db2631 omap-common/hwinit-common.c: Mark omap_rev_string as static
Only called in this file, mark as static.

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-04 16:32:31 -04:00
Inderpal Singh
b5f9756f7f exynos: update tzpc to make it common for exynos4 and exynos5
This requires that cpu_is_exynos4/5 should be made available before tzpc_init.
Hence this patch also makes necessary changes to have cpu_info in spl and
invokes arch_cpu_init before tzpc_init in low_level_init.S for smdk5250.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-04 15:23:17 +09:00
Inderpal Singh
72af2fc850 exynos: move tzpc_init to armv7/exynos
tzpc_init is common for all exynos5 boards, hence move it to
armv7/exynos so that all other boards can use it.

Also update the smdk5250 Makefile and config file.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-04 15:22:10 +09:00
Marek Vasut
86fb7b3d5b arm: mxs: Fix vectoring table crafting
The vectoring table has to be placed at 0x0, but U-Boot on MX23/MX28
starts from RAM, so the vectoring table at 0x0 is not present. Craft
code that will be placed at 0x0 and will redirect interrupt vectoring
to proper location of the U-Boot in RAM.

Signed-off-by: Marek Vasut <marex@denx.de>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-03 12:49:50 +02:00
Alison Wang
24e8bee508 arm: vf610: Add Vybrid VF610 CPU support
This patch adds generic codes to support Freescale's Vybrid VF610 CPU.

It aligns Vybrid VF610 platform with i.MX platform. As there are
some differences between VF610 and i.MX platforms, the specific
codes are in the arch/arm/cpu/armv7/vf610 directory.

Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-03 10:56:53 +02:00
Albert ARIBAUD
3da0e5750b arm: factorize relocate_code routine
Replace all relocate_code routines from ARM start.S files
with a single instance in file arch/arm/lib/relocate.S.
For PXA, this requires moving the dcache unlocking code
from within relocate_code into c_runtime_cpu_setup.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Simon Glass <sjg@chromium.org>
2013-05-30 20:24:38 +02:00
Albert ARIBAUD
fa6c7413d1 arm: do not compile relocate_code() for SPL builds
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Simon Glass <sjg@chromium.org>
2013-05-30 20:24:07 +02:00
Axel Lin
60985bba58 tegra: Define CONFIG_SKIP_LOWLEVEL_INIT for SPL build
Then we can get rid of the #ifdef CONFIG_TEGRA guard in cpu_init_crit.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-05-28 12:58:44 -07:00
Axel Lin
578e63782b ARM: arm720t: Add missing CONFIG_SKIP_LOWLEVEL_INIT guard for cpu_init_crit
cpu_init_crit() can be skipped, but the code is still enabled requiring a
platform to supply lowlevel_init().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-05-28 12:58:43 -07:00
Stephen Warren
20583d04fb ARM: tegra: support SKU 7 of Tegra20
Make U-Boot aware of the Tegra20 SKU 7, and treat it identically
to any other Tegra20.

My Whistler board has a SoC with this SKU.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-05-28 12:58:43 -07:00
Stephen Warren
840167c2c2 ARM: tegra: support SKU 1 of Tegra114
Make U-Boot aware of the Tegra114 SKU 1, and treat it identically
to any other Tegra114.

This value is used on (at least some) Dalmore boards with a production
rather than engineering chip. Such boards are in the hands of some
partners who want to use upstream U-Boot.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-05-28 12:58:43 -07:00
Allen Martin
a51f7de161 Tegra: clk: always use find_best_divider() for periph clocks
When adjusting peripheral clocks always use find_best_divider()
instead of clk_get_divider() even when a secondary divider is not
available.  In the case where is requested clock is too slow to be
derived from the parent clock this allows a best effort to get close
to the requested clock.

This comes up for commands like "sf" where the user can pass a clock
speed on the command line or "sspi" where the clock is hardcoded to
1MHz, but the Tegra114 SPI controller can't go that low.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-05-28 12:58:42 -07:00
Tom Rini
fd72569179 arm: Enable -ffunction-sections / -fdata-sections / --gc-sections
While other architectures have enabled these gcc / ld options for some
time on U-Boot itself, ARM has only been doing this on SPL.  Enable this
on full U-Boot as well now.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-23 12:09:56 +02:00
Akshay Saraswat
234370cab4 Exynos5: clock: Update the equation to calculate PLL output frequency
According to the latest exynos5 user manual, the equation for
calculating PLL output was changed to
FOUT= MDIV x FIN/(PDIV x 2^SDIV)
earlier it was
FOUT= MDIV x FIN/(PDIV x 2^(SDIV -1))
So updating the clock code accordingly.

Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-05-21 20:17:30 +09:00
Bo Shen
3225f34e5c ARM: atmel: add sama5d3xek support
Add sama5d3xek support with following feature
  - boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector
  - boot from SPI flash support
  - boot from SD card support
  - LCD support
  - EMAC support
  - USB OHCI support

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-21 11:54:16 +02:00
Wu, Josh
a73267a7ce arm: at91: enable mci support for at91sam9g20ek.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-12 16:42:24 +02:00
Wu, Josh
9e33690389 arm: at91: add at91sam9n12ek board support
Add support for following features:
  - nand boot, with PMECC 2bit ECC for 512 bytes sector
  - SPI flash boot
  - SD card boot
  - LCD support

Signed-off-by: Josh Wu <josh.wu@atmel.com>
[fix -Wimplicit-function-declaration for at91_lcd_hw_init()]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-12 16:40:42 +02:00
Albert ARIBAUD
cac423a730 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-05-11 22:24:28 +02:00
Albert ARIBAUD
ec7023db8d Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Conflicts:
	drivers/mtd/nand/mxc_nand_spl.c
	include/configs/m28evk.h
2013-05-11 09:25:36 +02:00
Albert ARIBAUD
e825b100d2 Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2013-05-11 00:06:03 +02:00
SRICHARAN R
47c6ea076e ARM: OMAP: Add arch_cpu_init function
The boot parameters passed from SPL to UBOOT
must be saved as a part of uboot's gd data
as early as possible, before we will inadvertently
overwrite it. So adding a arch_cpu_init for the required
Socs to save it.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:56 -04:00
SRICHARAN R
4a0eb75752 ARM: OMAP: Cleanup boot parameters usage
The boot parameters are read from individual variables
assigned for each of them. This been corrected and now
they are stored as a part of the global data 'gd'
structure. So read them from 'gd' instead.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:56 -04:00
SRICHARAN R
fda06812a0 ARM: OMAP: Correct save_boot_params and replace with 'C' function
Currently save_boot_params saves the boot parameters passed
from romcode. But this is not stored in a writable location
consistently. So the current code would not work for a
'XIP' boot. Change this by saving the boot parameters in
'gd' which is always writable. Also add a 'C' function
instead of an assembly code that is more readable.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-05-10 08:25:56 -04:00
SRICHARAN R
f92f2277a6 ARM: OMAP4/5: Make OMAPx_SRAM_SCRATCH_ defines common
These defines are same across OMAP4/5. So move them to
omap_common.h. This is required for the patches that
follow.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-05-10 08:25:56 -04:00
Tom Rini
30bba01751 am33xx: Fix warning with CONFIG_DISPLAY_CPUINFO
The arm_freq and ddr_freq variables are unused, so remove.  Fixup
whitespace slightly while in here.

Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:56 -04:00
Eric Benard
81ac7e51cc da850: provide davinci_enable_uart0
this is needed to bring UART0 out of reset but this function
currently only exists for dm644x/355/365/646x when da850 (at
least am1808 also need it).

Signed-off-by: Eric Bénard <eric@eukrea.com>
2013-05-10 08:25:56 -04:00
Lokesh Vutla
0b1b60c779 ARM: OMAP5: Fix warm reset with USB cable connected
Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.

There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.

In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'

In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
2013-05-10 08:25:55 -04:00
Lubomir Popov
2bcc785a1e OMAP5: USB: hsusbtll_clkctrl has to be in hw_auto for USB to work
USB TLL clocks do not support 'explicit_en', only 'hw_auto'
control (R. Sricharan). cm_l3init_hsusbtll_clkctrl has to be
moved to the clk_modules_hw_auto_essential[] array in order
to make the clock work.

This fix is needed (but not sufficient) for USB EHCI operation
in U-Boot.

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
2013-05-10 08:25:55 -04:00
Lokesh Vutla
166e5cc627 arm: omap: emif: Fix DDR3 init after warm reset
EMIF supports a global warm reset mode, during which the
EMIF keeps the SDRAM content. But if leveling is enabled
at the time of warm reset for DDR3, the following steps
needs to be done after warm reset:
1) Keep EMIF in self refresh mode.
2) Reset PHY to bring back the PHY to a known state.
3) Start Levelling procedure.
Doing the same.
And also enabling DLL lock and code output after warm reset.

Tested on OMAP5432 ES2.0

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-05-10 08:25:55 -04:00
Lubomir Popov
3935277dbf OMAP5: I2C: Enable i2c5 clocks
I2C4 and I2C5 are utilized on all known OMAP5 hardware platforms.
The i2c5 clock was however not enabled; do this here.

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
2013-05-10 08:25:55 -04:00
Matt Porter
035d563937 am33xx: add pll and clock support for TI814x CPSW
Enables required PLLs and clocks for CPSW on TI814x.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:54 -04:00
Marek Vasut
7411cdf0e2 arm: mxs: Add LCDIF clock configuration function
This function turns on the LCDIF clock and configures it's frequency. The
dividers settings are calculated within the function and the current
implementation should be fast and accurate.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-05-06 17:40:22 +02:00
Michal Simek
d5dae85f23 fpga: zynq: Add support for loading bitstream
Devcfg device requires to load bitstream in binary format.
But u-boot also has an option for loading bitstream in bit
format. Let's handle both cases by zynqpl driver.
Also add suport for loading partial bitstreams.

The first driver version was done by:
Joe Hershberger <joe.hershberger@ni.com>

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-05-06 10:41:24 +02:00
Marek Vasut
714dc001fc arm: mxs: Preprocess u-boot.bd so they contain full path
The u-boot-imx23.bd and u-boot-imx28.bd need to be preprocessed, otherwise
they have issues with out-of-tree build where elftosb tool couldn't sometimes
find the u-boot.bin and spl/u-boot-spl.bin .

Preprocess these .bd files with sed and insert full path to u-boot.bin and
spl/u-boot-spl.bin to prevent this issue. Moreover, to avoid adding more
churn into main Makefile, move all this preprocessing and u-boot.sb generation
into CPU directory instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2013-05-06 10:37:36 +02:00
Marek Vasut
dd3ecf020e arm: mx23: Fix VDDMEM misconfiguration
The VDDMEM ramped up in very weird way as it was horribly misconfigured.
Instead of setting up VDDMEM in one swipe, let it rise slowly the same
way as VDDD and VDDA in spl_power_init.c and then only clear ILIMIT before
memory gets inited. This makes sure the VDDMEM rises sanely, not jumps up
and down as it did till now.

The VDDMEM prior to this change did this:
     2V0____   .--------2V5
       |    `--'
 0V____|

The VDDMEM now does this:
    2V0_____,-----------2V5
      /
 0V__|

Moreover, VDDIO on MX23 uses 25mV steps while MX28 uses 50mV steps,
fix this difference too.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-05-06 10:20:33 +02:00
Fabio Estevam
286a88cf34 mxs: Explain why some mx23 DDR registers are not configured
Put an explanation in the source code as to why some DDR registers do not
need to be configured.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-06 09:55:52 +02:00
Fabio Estevam
26be20fac0 mx23: Operate DDR voltage supply at 2.5V
After the recent fixes in the mx23 DDR setup, it is safe to operate DDR voltage
at the recommended 2.5V voltage level again.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-06 09:55:51 +02:00
Łukasz Dałek
2ac2bb7ad2 pxa: Add weak attribute to reset_cpu() function
This commit allows pxa2xx based boards to reimplement reset_cpu()
function with board specific reset sequence.

Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
2013-05-05 23:47:05 +02:00
Benoît Thébaudeau
ba5dfc11ba imx: mx5: Remove legacy iomux support
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2013-05-05 17:55:05 +02:00
Benoît Thébaudeau
e2003c16c0 imx: mx35: Remove legacy iomux support
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05 17:55:04 +02:00
Benoît Thébaudeau
9e933b43f3 imx: mx25: Remove legacy iomux support
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05 17:55:03 +02:00
Marek Vasut
f399f63647 arm: mx5: Add NAND clock handling
Augment the MX5 clock code with function to enable and configure
NFC clock. This is necessary to get NFC working on MX5.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-05-05 17:45:05 +02:00
Fabio Estevam
fb7383a7a2 mxs: spl_mem_init: Change EMI port priority
FSL bootlets code set the PORT_PRIORITY_ORDER field of register HW_EMI_CTRL
as 0x2, which means:

PORT0231 = 0x02 Priority Order: AXI0, AHB2, AHB3, AHB1

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05 17:08:47 +02:00
Fabio Estevam
39a538d992 mxs: spl_mem_init: Skip the initialization of some DRAM_CTL registers
HW_DRAM_CTL27, HW_DRAM_CTL28 and HW_DRAM_CTL35 are not initialized as per
FSL bootlets code.

mx23 Reference Manual mark HW_DRAM_CTL27 and HW_DRAM_CTL28 as "reserved".

HW_DRAM_CTL8 is setup as the last element.

So skip the initialization of these DRAM_CTL registers.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05 17:08:46 +02:00
Fabio Estevam
b0d4bf9f0c mxs: spl_mem_init: Remove erroneous DDR setting
On mx23 there is no 'DRAM init complete' in register HW_DRAM_CTL18.

Remove this erroneous setting.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05 17:08:46 +02:00
Fabio Estevam
8a47c997c5 mxs: spl_mem_init: Fix comment about start bit
Start bit is part of HW_DRAM_CTL8 register, so  fix the comment.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05 17:08:46 +02:00
Andreas Bießmann
d2eae43ba8 lib: consolidate hang()
Delete all occurrences of hang() and provide a generic function.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-01 16:41:08 -04:00
Michal Simek
80243528ef net: gem: Fix gem driver on 1Gbps LAN
The whole driver used 100Mbps because of zc702 rev B.
Fix problem with not setup proper clock for gem1.
This is generic approach for clk setup.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:19 +02:00
Michal Simek
4b21284b8c zynq: Move scutimer baseaddr to hardware.h
Move baseaddr to hardware.h to be shared between
configurations.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:12 +02:00
David Andrey
d54cc00787 arm: zynq: U-Boot udelay < 1000 FIX
Rework the __udelay function of U-Boot Zynq Arch to handle
delay < 1000 usec

Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:10 +02:00
Benoît Thébaudeau
112fd2ec6c Add mxc_ocotp driver
Add an mxc_ocotp driver for i.MX6.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-28 11:07:43 +02:00
Benoît Thébaudeau
8f3ff11c1f imx: Homogenize and fix fuse register definitions
IIM:
 - Homogenize prg_p naming (the reference manuals are not always self-consistent
   for that).
 - Add missing SCSx and bank registers.
 - Fix the number of banks on i.MX53.

OCOTP:
 - Rename iim to ocotp in order to avoid confusion.
 - Rename fuse_data to read_fuse_data, and sticky to sw_sticky, according to the
   reference manual.
 - Merge the existing spinoff gp1 fuse definition on i.MX6.
 - Fix the number of banks on i.MX6.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-04-28 11:07:40 +02:00
Fabio Estevam
cdc203682f mx23: Put back RAM voltage level to its original value
commit 5c2f444c9 (mxs: Reset the EMI block on mx23) changed the DDR voltage
level, which causes mx23evk to fail to load a kernel.

Put back the original values, so that mx23evk can boot a kernel again.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
2013-04-28 11:06:27 +02:00
Fabio Estevam
11c08d4ec5 mx5: Define a common get_board_rev()
When booting a FSL kernel based on 2.6.35 it is necessary to pass the revision
tag to the kernel.

Place a common weak function into soc.c for such purpose.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2013-04-25 21:48:21 +02:00
Stefan Roese
ae695b18df mtd: mxs_nand: Add support for i.MX6
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-22 10:26:36 +02:00
Stefan Roese
8870e45996 imx: Move some i.MX common functions into the imx-common directory
This patch moves the following functions into the imx-common
directory:

- mxs_wait_mask_set()
- mxs_wait_mask_clr()
- mxs_reset_block()

These are currently used by i.MX28. But the upcoming GPMI NAND port
for i.MX6 will also use these functions. So lets move them to a
common location to re-use them.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-22 10:23:42 +02:00
Stefan Roese
0499218dbc imx: Move some header files from arch-mxs to imx-common
The following headers are moved to a i.MX common location:

- regs-common.h
- regs-apbh.h
- regs-bch.h
- regs-gpmi.h
- dma.h

This way this header can be re-used also by other i.MX platforms.
For example the i.MX6 which will need it for the upcoming NAND
support.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-22 10:22:22 +02:00
Fabio Estevam
25b4aa146a mx6: Add solo-lite variant support
mx6 solo-lite is another member of the mx6 series.

For more information about mx6 solo-lite, please visit:
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=i.MX6SL&nodeId=018rH3ZrDRB24A

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-22 09:57:44 +02:00
Stefano Babic
cd53034613 Merge branch 'next' 2013-04-21 11:32:19 +02:00
Simon Glass
dc47e2bc7d exynos: Correct use of 64-bit division
The current code is causing errors like this on my toolchains:

/usr/x86_64-pc-linux-gnu/armv7a-cros-linux-gnueabi/binutils-bin/2.22/
ld.bfd.real: failed to merge target specific data of file /usr/lib/gcc/
armv7a-cros-linux-gnueabi/4.7.x-google/libgcc.a(_divdi3.o)

Use do_div() to avoid this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-04-17 10:00:40 +09:00
Philip Paeps
04f79536c3 mx35 iomux: correct offsets of IOMUX registers
This makes mxc_iomux_set_input() work correctly.  Previously, the
incorrect offset of IOMUXSW_INPUT_CTL caused mxc_iomux_set_input()
to write to the wrong register, possibly resulting in unexpected
behaviour.

Signed-off-by: Philip Paeps <philip@paeps.cx>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-04-16 18:58:47 +02:00
Tom Warren
49493cb714 Tegra: Split tegra_get_chip_type() into soc & sku funcs
As suggested by Stephen Warren, use tegra_get_chip() to return
the pure CHIPID for a Tegra SoC (i.e. 0x20 for Tegra20, 0x30 for
Tegra30, etc.) and rename tegra_get_chip_type() to reflect its true
function, i.e. tegra_get_chip_sku(), which returns an ID like
TEGRA_SOC_T25, TEGRA_SOC_T33, etc.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-04-15 11:01:38 -07:00
Tom Warren
d94c2dbd0a Tegra: Fix MSELECT clock divisors for T30/T114.
A comparison of registers between our internal NV U-Boot and
u-boot-tegra/next showed some discrepancies in the MSELECT
clock divisor programming. T20 doesn't have a MSELECT clk src reg.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-04-15 11:01:38 -07:00
Tom Warren
b40f734af9 Tegra114: Initialize System Counter (TSC) with osc frequency
T114 needs the SYSCTR0 counter initialized so the TSC can be
read by the kernel. Do it in the bootloader since it's a write-once
deal (secure/non-secure mode dependent).

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-04-15 11:01:38 -07:00
Tom Warren
d0edce4fa3 Tegra: Configure L2 cache control reg properly.
Without this change, kernel fails at calling function cache_clean_flush
during kernel early boot.

Aprocryphally, intended for T114 only, so I check for a T114 SoC.
Works (i.e. dalmore 3.8 kernel now starts printing to console).

Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-04-15 11:01:38 -07:00
Tom Warren
3ebbbfe4c7 Tegra: Restore cp15 VBAR _start vector write for ARMv7
A start vector fix was added by AneeshV for OMAP4 (commit 0d479b53),
and caused the old monilithic Tegra builds to hang due to an undefined
instruction trap. Previously, the code needed to run on both the
AVP (ARM7TDI) and A9, and the AVP doesn't have a CP15 register.
I corrected this in commit 6d6c0bae w/#ifndef CONFIG_TEGRA, but
now that we use SPL, and boot the AVP w/o any ARMv7 code, I can
revert my change, and make Aneesh's change apply to Tegra.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-04-15 11:01:37 -07:00
Stephen Warren
eb222d1d7d ARM: tegra: support T33 SKU of Tegra30
Make U-Boot aware of the T33 SKU of Tegra30, and treat it identically
to any other Tegra30.

An alternative would be to simply remove the SKU checking from
tegra_get_chip_type(); most use of the value most likely simply wants
to know the current chip, not the specific SKU. Or, the function could
be split into separate tegra_get_chip() and tegra_get_sku() for the
cases where differentiation really is required.

I wonder whether tegra_get_chip_type() should printf() whenever any
unkown chip/SKU is found, although perhaps the function is called so
early that the printf() wouldn't actually make it to the UART anyway.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2013-04-15 11:01:37 -07:00
Andre Przywara
c4a4e2e20c ARMv7: start.S: stay in HYP mode if u-boot is entered in it
The KVM and Xen hypervisors for the Cortex-A15 virtualization
implementation need to be entered in HYP mode. Should the primary
board firmware already enter HYP mode (Calxeda firmware does that),
we should not deliberately drop back to SVC mode.
Since U-boot does not use the MMU, running in HYP mode is just fine.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-04-15 18:30:59 +02:00