When fdt_addr_t and phys_addr_t are split it turns out that
the header don't match the functions, so fix the headers.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In IPv6, the default gateway and prefix length are determined by receiving
a router advertisement as defined in -
https://www.rfc-editor.org/rfc/rfc4861.
Add support for sending router solicitation (RS) and processing router
advertisements (RA).
If the RA has prefix info option and following conditions are met, then
gatewayip6 and net_prefix_length of ip6addr env variables are initialized.
These are later consumed by IPv6 code for non-local destination IP.
- "Router Lifetime" != 0
- Prefix is NOT link-local prefix (0xfe80::/10)
- L flag is 1
- "Valid Lifetime" != 0
Timing Parameters:
- MAX_RTR_SOLICITATION_DELAY (0-1s)
- RTR_SOLICITATION_INTERVAL (4s) (min retransmit delay)
- MAX_RTR_SOLICITATIONS (3 RS transmissions)
The functionality is enabled by CONFIG_IPV6_ROUTER_DISCOVERY and invoked
automatically from net_init_loop().
Signed-off-by: Ehsan Mohandesi <emohandesi@linux.microsoft.com>
Tested-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>Reviewed-by:
Tested-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Tested-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Sergei Antonov <saproj@gmail.com>
Recent commit 75d28899e3 ("net: phy: Synchronize PHY interface modes
with Linux") reordered the enum definitions. This exposed a problem
in range checking functions to identify the interface type. Though
this specific api wasn't impacted (all the RGMII definitions remained
within range), this experience should be used to never to have to face
this kind of challenge again.
While it is possible for the phy drivers to use the enums directly,
drivers such as dp83867, dp83869, marvell, micrel_ksz90x1 etc use this
api.
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Recent commit 75d28899e3 ("net: phy: Synchronize PHY interface modes
with Linux") reordered the enum definitions. This caused the range of
enums that this api was checking to go bad.
There aren't anymore users of phy_interface_is_sgmii, so, just drop
it. Also the protocols are so very different that it makes no sense to
provide a helper wrapper in the hope of reuse for phy drivers.
Reported-by: Tom Rini <trini@konsulko.com>
Suggested-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Suggested-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/all/20230414103852.38705065@dellmb/
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Introduce reboot, boot and continue commands support to
TCP fastboot by moving existing UDP logic into the common module.
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Known limitations are
1. fastboot reboot doesn't work (answering OK but not rebooting)
2. flashing isn't supported (TCP transport only limitation)
The command syntax is
fastboot tcp
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make following changes to unblock TCP fastboot support:
1. Implement being a TCP server support
2. Introduce dedicated TCP traffic handler (get rid of UDP signature)
3. Ensure seq_num and ack_num are respected in net_send_tcp_packet
function (make sure existing wget_cmd code is reflected with the fix)
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Adds commands to support DHCP and PXE with IPv6.
New configs added:
- CMD_DHCP6
- DHCP6_PXE_CLIENTARCH
- DHCP6_PXE_DHCP_OPTION
- DHCP6_ENTERPRISE_ID
New commands added (when IPv6 is enabled):
- dhcp6
- pxe get -ipv6
- pxe boot -ipv6
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Adds DHCPv6 protocol to u-boot.
Allows for address assignement with DHCPv6 4-message exchange
(SOLICIT->ADVERTISE->REQUEST->REPLY). Includes DHCPv6 options
required by RFC 8415. Also adds DHCPv6 options required
for PXE boot.
Possible enhancements:
- Duplicate address detection on DHCPv6 assigned address
- IPv6 address assignement through SLAAC
- Sending/parsing other DHCPv6 options (NTP, DNS, etc...)
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Fix "setenv gatewayip6".
Synchronize IPv6 local variables with environment variables
in netboot_update_env()
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Export the ldpaa_eth_get_dpmac_id() function so that it can be used from
other drivers, especially by fsl-mc which will need it the next patch.
Also, create a macro for the Ethernet ldpaa driver name and export it as
well.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
When OE is packaging a dtb file into the FIT image it names the node based
on the dtb filename. Node names can't have "/" so it is turned into "_".
We select our FIT config using the "fdtfile" env var so we don't duplicate
the board_name to fdt logic. Result is fdtfile needs mangled when used to
select a config node from OE made FIT image. Do this here.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Using SMC relocation microcode patch or USB-SOF microcode patch
will disable DPRAM memory from 0x2000 to 0x2400 and from 0x2f00
to 0x3000.
At the time being, init RAM is setup to use 0x2800-0x2e00, but
the stack pointer goes beyond 0x2800 and even beyond 0x2400.
For the time being we are not going to use any microcode patch
that uses memory about 0x3000, so reorganise setup to use:
- 0x2800 - 0x2e00 for init malloc and global data and CPM buffers
- 0x3000 - 0x3c00 for init stack
For more details about CPM dual port ram, see
commit b1d62424cb ("powerpc: mpc8xx: redistribute data in CPM dpram")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Correct the function documentation.
Fixes: ca031c0827 ("dm: core: introduce uclass_get_device_by_of_path()")
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This platform is unsupported by TI and was never widely distributed. As
this is untested for a long while and missing some DM conversions,
remove it and related device tree files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds a simple Northstar "BRCMNS" board to be used with
the BCM4708x and BCM5301x chips.
The main intention is to use this with the D-Link DIR-890L
and DIR-885L routers for loading the kernel into RAM from
NAND memory using the BCH-1 ECC and using the separately
submitted SEAMA load command, so we are currently not adding
support for things such as networking.
The DTS file is a multiplatform NorthStar board, designed to
be usable with several NorthStar designs by avoiding any
particulars not related to the operation of U-Boot.
If other board need other ECC for example, they need to
create a separate DTS file and augment the code, but I don't
know if any other users will turn up.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This brings in the main SoC device tree used by the
Broadcom Northstar chipset, i.e. BCM4709x and BCM5301x.
This is taken from the v6.3 Linux kernel.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a new simple uclass for extcon. Currently all setup is done
in the probe. Uclass struct and ops are empty for now.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, it is recommended to move from CFG_EXTRA_ENV_SETTINGS to
an env file, so do the conversion.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add lockdown U-Boot env support so that only certain U-Boot environment
variables are allowed to be modified.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Instead of loading the zImage kernel and the devicetree separately, switch
to the fitImage format, which is more convenient when working with secure
boot, for example.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
GPT Partition labels are used for determining the right
root filesystem to boot from.
The U-Boot environment is configured to reside in the eMMC hardware
boot partition we are currently booted from.
This should enable a dual copy approach for upgrading the bootloader.
One can overwrite the inactive hardware partition with new bootloader
and environment and afterwards switch the eMMC boot partition for an
atomic bootloader switch.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
When performing rootfs update via swupdate, it is convenient to check the
'ustate' variable to decide whether the update succeeded or not.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Run the altbootcmd script if any step of bootcmd fails.
This ensures that always a valid image can be run.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add an altbootcmd script, which is convenient way to integrate with
swupdate and perform a roll back of the previous working version in the
case of update failure.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Introduce EXTRA_BOOTPARAMS to allow passing additional parameters
to kernel command line. This is useful for debugging purposes.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
The MNT Reform 2 is a modular DIY laptop. In its initial version it
is based on the BoundaryDevices i.MX8MQ SoM. Some parts have been
lifted from BoundaryDevices official U-Boot downstream project.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Please pull the second part of the sunxi pull request for this cycle.
Another bunch of patches that replace old-school U-Boot hacks with
proper DM based code, this time for the raw NAND flash driver, and the
USB PHY VBUS detection code. Plus two smaller patches that were sitting
in my inbox for a while.
Gitlab CI passed. In lack of some supported board with NAND flash I
couldn't really test this part, but apparently this was tested by the
reviewer. I briefly ran the branch on some boards with USB-OTG, and
this still worked.
This pull request adds support for the last CPU board from
CS GROUP France (previously CSSI).
That CPU board called CMPCPRO has a mpc8321E CPU (Family PQII PRO hence
its name) and can be plugged in place of the CMPC885 board.
In order to support that new board, the following changes are included
in this series:
- Make the mpc8xx watchdog driver more generic for reusing it
with mpc83xx
- Fix various small problems on mpc83xx platform
- Add a GPIO Driver for QE GPIOs
- Add support for mpc832x into mpc83xx SPI driver
- Refactor existing board code that will be shared with new board
- Add the new board
There's quite a few instances of board-specific code doing
off = fdt_path_offset(gd->fdt_blob, ...);
...
ret = uclass_get_device_by_of_offset(..., off, &dev);
looking for an eeprom or a pmic via some alias. Such code can be
simplified a little if we have a helper for directly getting a device
via device tree path (including being given as an alias).
Implement it in terms of ofnode rather than raw offsets so that this
will work whether live tree is enabled or not.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Given a file ../img of size 4294967296 with GPT partition table and
partitions:
=> host bind 0 ../img
=> part list host 0
Disk host-0.blk not ready
The cause is os_filesize() returning int. File sizes must use off_t.
Correct all uses of os_filesize() too.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The header binman_sym.h depends on ulong typedef but does not include
types.h. This means the header must be included after including types.h
or a header that includes it.
We could include types.h but instead let's just switch from ulong
to directly using unsigned long. This removes the need for typedef'ing
it in some of the tests, so also remove those.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Function fdt_simplefb_enable_existing_node() should be static as it is not
used outside common/fdt_simplefb.c.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CSSI has another CPU board, similar to the CMPC885 board
that get plugged on the two base boards MCR3000_2G and MIAE.
That CPU board is called CMPCPRO because it has a MPC8321E CPU,
also known as Power QUICC II PRO.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
All the code used to manage the mother boards will be
common to soon to come CPU board.
Move all that code into common.c
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As a first step toward converting this driver to the driver model, use
the ofnode abstraction to replace direct references to the FDT blob.
Using ofnode_read_u32_index removes an extra pair of loops and makes the
allwinner,rb property optional, matching the devicetree binding.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
add block storage emulation for NVM XIP flash devices
Some paltforms such as Corstone-1000 need to see NVM XIP raw flash
as a block storage device with read only capability.
Here NVM flash devices are devices with addressable
memory (e.g: QSPI NOR flash).
The implementation is generic and can be used by different platforms.
Two drivers are provided as follows.
nvmxip-blk :
a generic block driver allowing to read from the XIP flash
nvmxip Uclass driver :
When a device is described in the DT and associated with
UCLASS_NVMXIP, the Uclass creates a block device and binds it with
the nvmxip-blk.
Platforms can use multiple NVM XIP devices at the same time by defining a
DT node for each one of them.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Use IS_ENABLED() instead for all conditions. Add the 'lba48' flag into
struct blk_desc always, since it uses very little space. Use a bool so
the meaning is clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The use of atapi_read() was incorrect dropped. Fix this so that it will
be used when needed. Use a udevice for the first argument of atapi_read()
so it is consistent with ide_read().
This requires much of the ATAPI code to be brought out from behind the
existing #ifdef. It will still be removed by the compiler if it is not
needed.
Add an atapi flag to struct blk_desc so the information can be retained.
Fixes: 145df842b4 ("dm: ide: Add support for driver-model block devices")
Fixes: d0075059e4 ("ide: Drop non-DM code for BLK")
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
These are not used from outside this file anymore. Make them static and
remove them from the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the code does ide_init() as a separate operation, then calls
device_probe() to copy over the information. We can call ide_init() from
probe just as easily.
The only difference is that using 'ide init' twice will do nothing.
However it already fails to copy over the new data in that case, so the
effect is the same. For now, unbind the block devices and remove the IDE
device, which causes the bus to be probed again. Later patches will fix
this up fully, so that all blk_desc data is copied across.
Since ide_reset() is only called from ide_init(), there is no need to init
the ide_dev_desc[] array. This is already done at the end of ide_init() so
drop this code.
The call to uclass_first_device() is now within the probe() function of
the same device, so does nothing. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It doesn't really matter if we mention things which are not present. For
example, if 'nvme' is included but the board does not support it, it just
continues with the next item in the list.
It is simpler to use the same target list for all boards, so drop the
different one for rk3399.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the -l flag to indicate whether to report missing uclasses.
Also try to be more helpful when no devices are found. For example, when
we see something 'scsi0' requested and nothing was found, this indicates
that there are no SCSI devices, so show a suitable message.
Move messages out of the low-level functions so that silent operation
is possible.
This means they are never reported unless BOOTSTD_FULL is enabled, since
the -l flag cannot otherwise be set.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move to using .env file for setting up environment variables for am64x.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
In preparation for bouncing virtio data for devices advertising the
VIRTIO_F_IOMMU_PLATFORM feature, allocate an array of bounce buffer
structures in the vring, one per descriptor.
Signed-off-by: Will Deacon <willdeacon@google.com>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Link: 3e052749e7
Reviewed-by: Simon Glass <sjg@chromium.org>
In preparation for explicit bouncing of virtqueue pages for devices
advertising the VIRTIO_F_IOMMU_PLATFORM feature, introduce a couple
of wrappers around virtqueue allocation and freeing operations,
ensuring that buffers are handled in terms of page-size units.
Signed-off-by: Will Deacon <willdeacon@google.com>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Link: b4bb5227d4
Reviewed-by: Simon Glass <sjg@chromium.org>
Avoid using preprocessor compilation directives and instead use simple
logical expressions for better readability since compiler will anyway
optimize out the respective code block if condition is not satisfied.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
To include video related global data variables and splash functions at
SPL and u-boot proper, use CONFIG_IS_ENABLED.
Replace CONFIG_CMD_BMP with CONFIG_BMP to enable splash_display function
at u-boot proper and SPL.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To enable splash screen at SPL, need to compile cmd/bmp.c which also
includes bmp commands, since SPL doesn't use commands split bmp.c into
common/bmp.c which includes all bmp functions and cmd/bmp.c which only
contains bmp commands.
Add function delclaration for bmp_info in video.h.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The J7200 EVM will not include this file, this J7200 checks look
to be a copy/paste errora from j721e_evm.h, which J7200 *can* include.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
- Add rk3588 evb support;
- Update pinctrl for rk3568 and rk3588;
- Update rk3288 dts;
- Update mmc support for rk3568 and rk3588;
- Add rng support for rk3588;
- Add DSI support for rk3568;
- Some other misc fixes in dts, config, driver;
- watchdog: arm_smc_wdt: add watchdog support (Lionel)
- watchdog: ftwdt010: return a previously deleted driver now ported to
DM (Sergei)
- watchdog: Add a watchdog driver for Raspberry Pi boards (Etienne)
Add fdtoverlay_addr_r, kernel_comp_addr_r and imply use of
OF_LIBFDT_OVERLAY on RK3568 and RK3588 to support fdtoverlay
and kernel compression.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
rk3588 evb1 v10 is a evalution board from Rockchip, it is a dev board for
rockchip and also a reference board for board vendors.
Hardware:
SoC: RK3588
DRAM: LPDDR4X 8GB
Debug: UART2 via USB
PCIe: 3x4 *1
SATA *2
HDMI out *2
HDMI IN *1
USB2.0 Host *2
USB3.0 Host *1
Type C *1
MIPI DSI panel
dts Sync from Linux v6.2.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
When a structure contains a flexible array member, it is not supposed to be
included in arrays or other structs.
Quoting the C spec [0]
"Such a structure (and any union containing, possibly recursively, a
member that is such a structure) shall not be a member of a structure
or an element of an array."
IOW efi_hii_keyboard_layout should not include
struct efi_key_descriptor descriptors[]; since we use it at the
declaration of struct efi_hii_keyboard_package.
[0] https://www.dii.uchile.cl/~daespino/files/Iso_C_1999_definition.pdf
chapter 6.7.2.1
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add board support for StarFive VisionFive v2.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add all clock outputs for the StarFive JH7110 clock generator.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add resets for the StarFive JH7110 system(SYS),system-top-group(STG) and
always-on(AON) reset controller.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
With some USB device, the current usb_pgood_delay value is not long
enough to ensure a correct detection.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add usb_pgood_delay to ensure a correct detection of USB devices.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The ftwdt010 watchdog driver was deleted by
commit 11232139e3 ("nds32: Remove the architecture")
Return it to the codebase in a DM compatible form. Enable it in
sandbox_defconfig to test compilability.
Another platform using ftwdt010 will be submitted later.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
-----BEGIN PGP SIGNATURE-----
iQJYBAABCgBCFiEE6GOTDNYiFygVXvMmQBtB6IWRjvEFAmQ9ALMkHGRhcmlvLmJp
bmFjY2hpQGFtYXJ1bGFzb2x1dGlvbnMuY29tAAoJEEAbQeiFkY7x6YMP/3vW6t7v
R0y3pGS0CcZhOtxLKH2Z5KbC6qoFmkK40vqvrKyUX1m4haJ+4A6BJR/rvdTCNftP
2ezpSF5SV7ZnG6+DIuY3Zvh7Jr9+ApuMmsm2vPeg8bv8gevzq3dHMk8msZb3P9+c
YX0FOpukZcJiYI9p2d+AFBLS2ETvfOYNhcfGu9PP1LdlChu1VL5BTwxmiKPuNf7D
6Rte3he0JubiLGp3CnLnj+o2l2OVrj+Kokv+jBCVVDtaVujD8tUCT+FJ/8FrXgFS
S/IOxV1DwhaxGHEjzM6ozq94b2lKB1v9PvapmveQSRmY+O01Q108uFUxMw5G6RyS
tEzoqdTk6u5Gzv/arsbXNSPe6i41QY454NqA5tOdUYprMQKM8k/P+ow9c5r4VRMH
YybBqYMAYs/9qmhBBfHhMnwEpzpHxBVTBTWtdqEIP85FcDgDV6HOs3imx05VnMe4
jfUBja5I0rzo9i7tvOhOOr4KTA1Qdg4xGTEm2nvKXHoIrGm3pC4wY54Q1F2UNm1b
osyqUh9pHqlgy+/8VPsUmu8zoewH/j4tGl1JRhYPd2QmYPlI7lDkhRtOBGOzBDAF
xvUQd5F2sYw6bDe7kiUfoX37Uy8cDupAETEYLpnGqG2/sLDo5p/VPNEiETAbfCmV
yVTDYvljxy/l3sqTUqbmkYS7V64UUc8tn0ql
=1lGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230417' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
Pull request for u-boot-nand-20230417
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
There is an existing CONFIG_MCFTMR Kconfig symbol,
use it and drop all other instances of CFG_MCFTMR.
This duality is likely a result of bogus conversion
to Kconfig.
Fixes: 7ff7b46e6c ("m68k: rename CONFIG_MCFTMR to CFG_MCFTMR")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
When secure/insecure TRIM operations are supported.
When used as erase command argument it applies the
erase operation to write blocks instead of erase
groups.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Documentation:
* man-page for coninfo command
* documentation style
* switch settings for boot modes on AM62 SK
UEFI:
* avoid using deprecated HandleProtocol()
* set static attribute for non-exported functions and variables
-----BEGIN PGP SIGNATURE-----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=bYxY
-----END PGP SIGNATURE-----
Merge tag 'efi-2023-07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2023-07-rc1
Documentation:
* man-page for coninfo command
* documentation style
* switch settings for boot modes on AM62 SK
UEFI:
* avoid using deprecated HandleProtocol()
* set static attribute for non-exported functions and variables
Add board code for R8A779G0 V4H White Hawk board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add all Clock Pulse Generator Core Clock Outputs for the
Renesas R-Car V4H (R8A779G0) SoC from Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tho Vu <tho.vu.wh@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update to linux next 20230228 state]
Add power domain indices for R-Car V4H (R8A779G0) from Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tho Vu <tho.vu.wh@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update to linux next 20230228 state]
Add board code for R8A779F0 S4 Spider board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add definitions for R8A779F0 S4 CPG Core Clock headers from Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tho Vu <tho.vu.wh@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update to linux next 20230228 state]
Add power domain indices for R-Car S4 (R8A779F0) from Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tho Vu <tho.vu.wh@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update to linux next 20230228 state]
Provide the basic HSCIF support for R-Car SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Fill in HSSRR offset for Gen2 and SCBRR calculation for Gen2 and Gen3]
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds R-Car Generation 4 (Gen4) support as Renesas ARM64 SoC.
In this version, reusing R-Car Gen3 lowlevel initialize routine [1]
and R-Car Gen3 memory map tables [2] .
[1] arch/arm/mach-rmobile/lowlevel_init_gen3.S
[2] arch/arm/mach-rmobile/memmap-gen3.c
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: - Enable DTO support by default
- Sort the Kconfig lists
- Select RCAR_64 Kconfig option to pull in all the shared
Kconfig options with Gen3, and use where applicable to
deduplicate entries.
- Fix reference [2] typo in commit message
- Drop config options moved to Kconfig, rename rest to CFG_
accordingly to synchronize with upstream changes. Drop
removed CONFIG_VERY_BIG_RAM.
- Move board size limit to arch/Kconfig
- Move GICR_BASE to headers instead of common config]
Add two new callbacks matching the Linux ones. The .set_mode is used to set
PHY mode and submode, where mode is either USB, Ethernet, and so on, while
submode is e.g. for Ethernet case RGMII, RMII, and so on. The .set_speed is
used to configure link speed into the PHY. Unlike the existing configure
callback, which is used to pass arbitrary custom information to the PHY,
these two callbacks are used to pass standardized set of information to
the PHY.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Insert missing space in front of asterisk to avoid checkpatch warning.
Replace 'beeing' with 'being' as well, to fix another checkpatch warning.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case PHY is not enabled, the generic_phy_configure() implementation is
missing. Add an empty one so that the list of empty functions is complete.
Fixes: f8da8a82c5 ("generic-phy: add configure op")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add MDIO PCS 2.5G and 5G speed macros from Linux 5.1.y as of commit
7fd8afa8933a0 ("net: phy: Add generic support for 2.5GBaseT and 5GBaseT")
This is used by the upcoming Marvell 10G PHY driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add phy_read_mmd_poll_timeout() from Linux 5.7.y as of commit
bd971ff0b7392 ("net: phy: introduce phy_read_mmd_poll_timeout macro")
This is used by the upcoming Marvell 10G PHY driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add phy_modify_mmd()/phy_modify_mmd_changed() from Linux 5.1.y as of commit
b8554d4f7288f ("net: phy: add register modifying helpers returning 1 on change")
This is used by the upcoming Marvell 10G PHY driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Import marvell_phy.h from Linux 5.14.y as of commit
a5de4be0aaaa6 ("net: phy: marvell10g: fix differentiation of 88X3310 from 88X3340")
and use it in marvell PHY driver instead of current ad-hoc macros.
Two of the PHY IDs are unknown to Linux, 88E1149S and 88E1680, for
those two, only sync the length of the hexadecimal number to 8 digits.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Synchronize PHY interface modes with Linux next 6.2.y commit:
0194b64578e90 ("net: phy: improve phy_read_poll_timeout")
Retain LX2160A/LX2162A PHY modes as those are not yet supported
by the Linux kernel, but isolate those with ifdeffery.
Isolate NCSI which are also not supported by Linux kernel. Note
that the ifdeffery cannot be avoided with IS_ENABLED() here due
to compilation of the entire conditional, which would fail in
case NCSI symbols are not available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Replace PHY_INTERFACE_MODE_SFI with PHY_INTERFACE_MODE_5GBASER,
PHY_INTERFACE_MODE_10GBASER and PHY_INTERFACE_MODE_XAUI to match
Linux PHY interface modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This function is no longer used, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
The static phy_drivers list is superseded by linker list of struct phy_drivers
now that all drivers have been converted to the later. Drop the phy_drivers
list as well as list_head from struct phy_driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
This particular PHY driver is slightly more spread out across additional
source files. Since the phy_register() calls are no longer necessary, all
the registration calls across those source files is dropped. Furthermore,
the Makefile can now be updated to only compile generic TI PHY support if
matching Kconfig symbol is enabled and the ifdeffery in the generic TI PHY
driver can be dropped.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Introduce U_BOOT_PHY_DRIVER() macro which is used to add struct phy_driver
into a new linker list section containing all compiled in struct phy_driver
drivers. This is so far empty until PHY drivers are converted over to this
macro.
Iterate over both drivers registered using soon to be legacy phy_register()
as well as drivers in the new linker list when looking up a suitable PHY
driver. This way, PHY drivers can be converted over to the new macro one
driver at a time.
The relocation of callbacks for linker list based drivers now happens in
phy_init() call as the drivers are available at that point in time, and
phy_register() is not called for those drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Remove test on CONFIG_LMB_MEMORY_REGIONS introduced by commit
7c1860fce4 ("lmb: Fix lmb property's defination under struct lmb").
This code in lmb_init() is strange, because if CONFIG_LMB_USE_MAX_REGIONS
and CONFIG_LMB_MEMORY_REGIONS are not defined, the implicit #else is empty
and the required initialization is not done:
lmb->memory.max = ?
lmb->reserved.max = ?
But this setting is not possible:
- CONFIG_LMB_USE_MAX_REGIONS not defined
- CONFIG_LMB_MEMORY_REGIONS not defined
because CONFIG_LMB_MEMORY_REGIONS and CONFIG_LMB_RESERVED_REGIONS are
defined as soon as the CONFIG_LMB_USE_MAX_REGIONS is not defined.
This patch removes this impossible case #elif and I add some
explanation in lmb.h to explain why in the struct lmb {} the lmb
property is defined if CONFIG_LMB_MEMORY_REGIONS is NOT defined.
This patch also removes CONFIG_LMB_XXX dependency on CONFIG_LMB as these
defines are used in API file lmb.h and not only in library file.
Fixes: 5e2548c1d6 ("lmb: Fix LMB_MEMORY_REGIONS flag usage")
Reported-by: Mark Millard <marklmi@yahoo.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Create a distinct EFI device path for each blkmap device.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow a slice of an existing block device to be mapped to a
blkmap. This means that filesystems that are not stored at exact
partition boundaries can be accessed by remapping a slice of the
existing device to a blkmap device.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow a slice of RAM to be mapped to a blkmap. This means that RAM can
now be accessed as if it was a block device, meaning that existing
filesystem drivers can now be used to access ramdisks.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
blkmaps are loosely modeled on Linux's device mapper subsystem. The
basic idea is that you can create virtual block devices whose blocks
can be backed by a plethora of sources that are user configurable.
This change just adds the basic infrastructure for creating and
removing blkmap devices. Subsequent changes will extend this to add
support for actual mappings.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable the support for boot image header version 3 and 4
using abootimg command.
In order to use version 3 or 4:
1- Vendor boot image address should be given to abootimg cmd.
abootimg addr $1 $vendor_boot_load_addr
2- "ramdisk_addr_r" env variable (ramdisk address) should be set to host
the ramdisk : generic ramdisk + vendor ramdisk
Replace "struct andr_boot_img_hdr_v0*" by "void *" in
some functions since v3 and v4 are now supported as well.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Version 3 and 4 of boot image header introduced
vendor boot ramdisk: Please check include/android_image.h
for details.
The ramdisk is now split into a generic ramdisk in boot image
and a vendor ramdisk in vendor boot image.
Support the new vendor ramdisk.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Since boot image header version 3 and 4 introduced vendor boot image,
use the following functions to fill the generic android
structure : andr_image_data:
- android_boot_image_v3_v4_parse_hdr()
- android_vendor_boot_image_v3_v4_parse_hdr()
Update android_image_get_data() to support v3 and v4
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Introduce vendor boot image for version 3 and 4 of boot image header.
The vendor boot image will hold extra information about kernel, dtb
and ramdisk.
This is done to prepare for boot image version 3 and 4 support.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
andr_image_data structure is used as a global representation of
boot image header structure. Introduce this new structure to
support all boot header versions : v0,v1.v2.v3.v4 and to support
v3 and v4 while maitaining support for v0,v1,v2.
The need of using andr_image_data comes from the change of header
structure in both version 3 and 4.
Rework android_image_get_kcomp() to support this new struct.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
With the new vendor boot image introduced in versions 3 and 4
of boot image header, the header check must be done for both boot
image and vendor boot image. Thus, replace android_image_check_header()
by is_android_boot_image_header() to only refer to boot image header check.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Android introduced boot header version 3 or 4.
The header structure change with version 3 and 4 to support
the new updates such as:
- Introducing Vendor boot image: with a vendor ramdisk
- Bootconfig feature (v4)
Change andr_img_hdr struct name to maintain support for version v0,
v1 and v2 while introducing version 3 and 4.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Per the GCC bug listed below, the way we do linker lists is relying on
undefined behavior that seems to work in gcc, but doesn't always work in
clang. Andrew suggests rewriting our start/end macros in a different way
(as implemented here, from what he said in comment 1) to avoid these
problems.
Reported-by: AdityaK <appujee@google.com>
Suggested-by: Andrew Pinski <apinski@marvell.com>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=108915
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andrew Pinski <apinski@marvell.com>
Beacon Embedded has an i.MX8M Plus development kit which consists
of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC,
and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual
Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet
PHY. The device trees are already queued for inclusion in Linux 6.3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Data Modul i.MX8M Plus eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR, USB.
Signed-off-by: Marek Vasut <marex@denx.de>
Enable SDP protocol support in SPL for DH i.MX6 DHSOM, now that those
components fit into the SPL due to LTO.
To start U-Boot via SDP upload on i.MX6 DHSOM based board, proceed as follows:
- Compile imx_usb [1] .
- Power off the i.MX6 DHSOM based board.
- Connect both USB-serial console and USB-OTG miniB ports to host PC.
- Switch board to USB boot mode.
- Power on the board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=15a2, idProduct=0054, bcdDevice= 0.01
New USB device strings: Mfr=1, Product=2, SerialNumber=0
Product: SE Blank ARIK
Manufacturer: Freescale SemiConductor Inc
- Upload U-Boot SPL:
$ imx_usb u-boot-with-spl.imx
- Wait for SPL to come up, the following print ought to be the last on
UART console:
SDP: handle requests...
- Upload U-Boot proper:
$ imx_usb u-boot.img
[1] https://github.com/boundarydevices/imx_usb_loader.git
Signed-off-by: Marek Vasut <marex@denx.de>
We use short device-paths in boot options so that a file on a block device
can be found independent of the port into which the device is plugged.
Usb() device-path nodes only contain port and interface information and
therefore cannot identify a block device.
UsbWwi() device-path nodes contain the serial number of USB devices.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCZCaU0Q8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76YCKgCgk4OueoIggmes+Ccj8bu1BcQbrfYAoJAgMeKE
It0hrVAifD62TPb2rmHt
=hFVG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-next-20230331' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
u-boot-imx-next-20230331 for next
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
The Linux kernel device tree already specifies the device to be used for
boot console output with a stdout-path property under /chosen.
Commit 36b661dc91 ("Merge branch 'next'") re-added the console
setting that commit bede82f750 ("configs: imx8mn_bsh_smm_s2: remove
console from bootargs") had previously removed.
Fixes: 36b661dc91 ("Merge branch 'next'")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
* vsnprintf() can truncate cmd, hence it makes no sense to launch such
command (it's broken). Moreover, it's better to signalize to the caller
about such case (for facilitating debugging or bug hunting).
* Fix kernel-doc warnings:
include/command.h:264: info: Scanning doc for run_commandf
include/command.h:268: warning: contents before sections
include/command.h:271: warning: No description found for return value
of 'run_commandf'
* Add printf-like format attribute to validate at compile-time the format
string against parameters's type.
* Fix compilation error in case of -Wall, -Werror, -Wextra:
error: variable ‘i’ set but not used [-Werror=unused-but-set-variable]
* Drop extra ret variable.
Signed-off-by: Evgeny Bachinin <EABachinin@sberdevices.ru>
Reviewed-by: Simon Glass <sjg@chromium.org>
The find_closest() macro can be used to find an element in a sorted
array that is closest to an input value. Bring in this macro from
Linux v6.3-rc1-2-g8ca09d5fa354.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The API is more convenient to use if one doesn't have to know upfront
which gpio controller has a line with the name one is searching for,
and arrange to look that device up somehow. Or implement this loop
oneself.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds a test for the new pci_mps command to ensure that it can set the
Maximum Payload Size (MPS) of all devices to 256 bytes in the sandbox
environment. Enables the pci_mps command in the sandbox environment so
that this test can be run.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Enable tuning of the PCI Express MPS (Maximum Payload Size) of
each device. The Maximum Read Request Size is not altered.
The SAFE method uses the largest MPS value supported by all devices in the
system for each device. This method is the same algorithm as used by Linux
pci=pcie_bus_safe.
The PEER2PEER method sets all devices to the minimal (128 byte) MPS, which
allows hot plug of devices later that might only support the minimum size,
and ensures compatibility of DMA between two devices on the bus.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Move i.MX auxiliary core memory base and size configuration
to defconfig where it should belong.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Update the distro config env memory layout for the Colibri iMX8X:
- kernel_comp_addr_r=0xb0000000 temporary area for uncompressing (ie FIT
images or Image.gz booted using booti)
- kernel_comp_size=0x08000000
- loadaddr=0x95400000 avoiding any reserved areas located before that
- fdt_addr_r = loadaddr + 128MB - allows for 128MB kernel
- scriptaddr = fdt_addr_r + 512KB - allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB - allows for 512KB script
Idea of memory layout taken from commit a9f1e35bed
("apalis-imx8: update env memory layout").
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
The following expression is used to construct the device tree name:
fdtfile=${soc}-colibri-${fdt_board}.dtb
- soc is set dynamically (either imx8qxp or imx8dx)
- fdt_board can be modified by the user (eval-v3, aster, iris/iris-v2)
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Remove obsolete SDHC related config defines. Nowadays, all SDHC related
hardware configuration comes from the device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Remove obsolete net USB start.
While at it also add a comment about enabling distro-boot.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
This commit does remove the options argument from the console
kernel-argument as it prevents the serial driver from outputting
anything.
Do this by switchting to use the variable "setup" as it is done on other
Toradex modules.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Add mmc1, which is mapped to optional on-SoM microSD socket,
to the list of distro boot command boot devices.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
PCA9451A uses similar BUCKs and LDO regulators as PCA9450B/C but
has LDO2 and LDO3 removed. So reuse pca9450 PMIC and regulator driver
and add new type for PCA9451A.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The usage of DM_PMIC is preferred, so convert to it.
This also brings the benefit of causing a significant amount
of code removal.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The usage of DM_PMIC is preferred, so convert to it.
This also brings the benefit of causing a significant amount
of code removal.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Move to using .env file for setting up environment variables for am65x.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move to using .env file for setting up environment variables for J721E
and J7200.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move to using .env file for setting up environment variables for J721S2.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add K3 common environment variables to .env. We retain the old-style C
environment .h files to maintain compatibility with other K3 boards that
have not moved to using .env yet.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The M.2 slots of the related IOT2050 variant need to be configured
according to the plugged cards. This tries to detect the card using the
M.2 configuration pins of the B-key slot. If that fails, a U-Boot
environment variable can be set to configure manually. This variable is
write-permitted also in secure boot mode as it is not able to undermine
the integrity of the booted system.
The configuration is then applied to mux the serdes and to fix up the
device tree passed to or loaded by the bootloader. The fix-ups are
coming from device tree overlays that are embedded into the firmware
image and there also integrity protected. The OS remains free to load
a device tree to which they do not apply: U-Boot will not fail to boot
in that case.
Based on original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Will be needed when CONFIG_ENV_WRITEABLE_LIST is enabled. The listed
variables shall remain writable, for informational purposes - they have
to be considered untrusted because the persistent U-Boot env is not
protected.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Anything that is not boot-env related is better kept there by now.
At this chance, also drop a stale comment from iot2050.h
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The second call to cli_ch_process() is in the wrong place, meaning that
the one of the characters of an invalid escape sequence is swallowed
instead of being returned.
Fix the bug and add a test to cover this.
This behaviour matches that of the code before cli_getch() was
introduced. This was verified on the commit before b08e9d4b66 i.e.:
7d850f85aa ("sandbox: Enable mmc command and legacy images")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The defined altbootcmd was specific to distro_bootcmd which is not
longer in use on these platforms, so drop it.
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
This code is used with EFI_LOADER but is also useful (with some
modifications) for the EFI app and payload. Move it into a shared
file.
Show the address of the table so it can be examined if needed. Also show
the table name as unknown if necessary. Our list of GUIDs is fairly
small.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide information about the GUIDs supplied by QEMU, so far as it is
known.
These values are used in the 'efi table' command as well as the printf
format string %sU
Signed-off-by: Simon Glass <sjg@chromium.org>
The incumbent function efi_alloc() is unused.
Replace dp_alloc() by a new function efi_alloc() that we can use more
widely.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
* Add the definitions for Ctrl() device path nodes.
* Implement Ctrl() nodes in the device path to text protocol.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
* Add the definitions for Ctrl() device path nodes.
* Implement Ctrl() nodes in the device path to text protocol.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We did not add a prototype for spl_mmc_get_uboot_raw_sector to
include/spl.h before, so add and document one now. Correct the incorrect
prototype in board/advantech/imx8mp_rsb3720a1/imx8mp_rsb3720a1.c and
ensure that we have spl.h where we define a non-weak
spl_mmc_get_uboot_raw_sector as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This removes dangling comments that no longer serve a purpose and has
been left after conversion of defines to Kconfig option.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Building U-Boot for Tinker Board with USB or NET Kconfig option disabled
result in the following build error:
In file included from include/configs/rk3288_common.h:29,
from include/configs/tinker_rk3288.h:14,
from include/config.h:3,
from include/common.h:16,
from env/common.c:10:
include/config_distro_bootcmd.h:302:9: error: expected '}' before 'BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB'
302 | BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:302:9: note: in definition of macro 'BOOTENV_DEV_NAME_USB'
302 | BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/configs/tinker_rk3288.h:21:9: note: in expansion of macro 'BOOTENV_DEV_NAME'
21 | func(USB, usb, 0) \
| ^~~~
include/config_distro_bootcmd.h:454:25: note: in expansion of macro 'BOOT_TARGET_DEVICES'
454 | "boot_targets=" BOOT_TARGET_DEVICES(BOOTENV_DEV_NAME) "\0"
| ^~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:474:9: note: in expansion of macro 'BOOTENV_BOOT_TARGETS'
474 | BOOTENV_BOOT_TARGETS \
| ^~~~~~~~~~~~~~~~~~~~
include/configs/rk3288_common.h:40:9: note: in expansion of macro 'BOOTENV'
40 | BOOTENV
| ^~~~~~~
include/env_default.h:122:9: note: in expansion of macro 'CFG_EXTRA_ENV_SETTINGS'
122 | CFG_EXTRA_ENV_SETTINGS
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from env/common.c:32:
include/env_default.h:29:36: note: to match this '{'
29 | const char default_environment[] = {
| ^
make[2]: *** [scripts/Makefile.build:256: env/common.o] Error 1
The BOOT_TARGET_DEVICES defined in rockchip-common.h include the same
devices as defined in tinker_rk3288.h, remove the board specific one to
fix building with USB or NET option disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
binman signing feature
fix buildman -A bug introduced recently
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmQQ8KIRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYRmwgA1XAHafEOfhaya54nalUgW9qYZe5Ntfqd
4Tg7zj3gadZuv82LuyskEyBKptwRCzgX0Tyx62V3Oop9vJ/cCwjIB4AGhCsMKERf
NqcMd8fbGbJ9jJzOp7gNTHzV4vSmwKM0lRkxbClMFcvMsfVdKcBRPswLLghk5/xL
Uu4Ww4yfe7UCqgBm9uouVaIbcNNcl8p0QnSJT9HvwjGKawPT6uSHOHK9Wpkud0q1
ZyrPpCMA29mifhIU8aH5CJH5G61UbGcVSDhm9lIKwqZg+KJGuYf64JbZoY9JI2/z
pOUHLZx7fVHoFyWKWfVkA9l6HRjZTRc0nJhYFx5HyNUOU50hMENeTQ==
=ko2P
-----END PGP SIGNATURE-----
Merge tag 'dm-next-12mar23a' of git://git.denx.de/u-boot-dm into next
More tests and fixes for fdt command
binman signing feature
fix buildman -A bug introduced recently
Signed-off-by: Tom Rini <trini@konsulko.com>
Per Andre:
[T]hese two patches containing just devicetree updates for
Allwinner boards.
I was still hoping for a review, since we cannot import the files from
the Linux tree verbatim, but managed to write some filter script that
convinced me that the changes are fine.
The files are from Linux v6.2-rc2, but are identical to the v6.2
release.
Remove CONFIG_ namespace options from .h, moving them to
defconfig, while changing non-defconfig options to CFG_ namespace.
Signed-off-by: Angelo Durgehello <angelo@kernel-space.org>
Wrap the assert macros in ({ ... }) so they can be safely used both as
right side argument as well as in conditionals without curly brackets
around them. In the process, find a bunch of missing semicolons, fix
them.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
It is better to clear the console device rather than the video device,
since the console has the text display. We also need to reset the cursor
position with the console, but not with the video device.
Add a new function to handle this and update the 'cls' command to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is not possible for the video driver to use a pre-allocated
frame buffer (such as is done with EFI) with the copy framebuffer. This
can be useful to speed up the display.
Adjust the implementation so that copy_size can be set to the required
size, with this being allocated if the normal framebuffer size is 0.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current vesa structure only provides a 32-bit value for the frame
buffer. Many modern machines use an address outside the range.
It is still useful to have this common struct, but add a separate
frame-buffer address as well.
Add a comment for vesa_setup_video_priv() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add helper macro to test for empty lines, which is an inobvious
wrapper around ut_assert_nextline("%s", "") .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add helper macro to test for empty lines, which is an inobvious
wrapper around ut_assert_nextline("%s", "") .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
For EFI, the distro boot scripts search in three different directories
for the .dtb file. The SOC-based filename fallback is supported only for
32-bit ARM.
Adjust the code to mirror this behaviour.
Also some boards can use a prior-stage FDT if one is not found in the
normal way. Support this and show a message in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Mark Kettenis <kettenis@openbsd.org>
- support for fonts wider than 1 byte
- use named header for 8x16 font data
- support multiple fonts configuration
- move get_font_size() to truetype driver ops
- support font size configuration at runtime
- add 16x32 Terminus font from linux
- add 12x22 Sun font from linux
- add 12x22 console simple font test
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZAdiLw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXDtGAJ9ZjsnfneJpUjwYJWOw2ibnm9Dh2QCfVCAy+Bxa
YfqV8y7TbOuCQKTEY1s=
=FJhw
-----END PGP SIGNATURE-----
Merge tag 'next-20230307' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- video console refactoring and optimization
- support for fonts wider than 1 byte
- use named header for 8x16 font data
- support multiple fonts configuration
- move get_font_size() to truetype driver ops
- support font size configuration at runtime
- add 16x32 Terminus font from linux
- add 12x22 Sun font from linux
- add 12x22 console simple font test
Modern mobile phones typically have high pixel density.
Bootmenu is hardly readable on those with 8x16 font.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Modern mobile phones typically have high pixel density.
Bootmenu is hardly readable on those with 8x16 font.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since multiple vidconsole drivers exists, vidconsole_get_font_size()
implementation cannot longer live in vidconsole_uclass.c file.
Move current vidconsole_get_font_size logic to truetype driver ops.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This needed for unit testing different fonts.
Configured fonts are placed in an array of fonts.
First font is selected by default upon console probe.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[agust: fixed build error when bmp logo disabled]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Consistent font data header names needed to add new
fonts.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- move common code to vidconsole_internal.h and console_core.c
- unite probe functions
- get rid of code duplications in switch across bpp values
- extract common pixel fill logic in two functions one per
horizontal and vertical filling
- rearrange statements in put_xy* methods in unified way
- replace types - uint*_t to u*
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fttmr010 timer driver was deleted by
commit 29fc6f2492 ("ARM: remove a320evb board support")
The original source file was: arch/arm/cpu/arm920t/a320/timer.c
Return the driver to the codebase in a DM compatible form.
A platform using fttmr010 will be submitted later.
This hardware is described in the datasheet [1], starting from page 348.
According to the datasheet, there is a Revision Register at offset 0x3C,
which is not present in 'struct fttmr010'. Add it and debug() print
revision in probe function.
[1]
https://bitbucket.org/Kasreyn/mkrom-uc7112lx/src/master/documents/FIC8120_DS_v1.2.pdf
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Sync the devicetree files from the Linux kernel repo, v6.2-rc2.
This is covering the 32-bit SoCs, from arch/arm/boot/dts.
This enables some new devices for the F1C100s family, though this is of
little relevance to U-Boot itself.
The H3 gains the "phys" property for the first USB controller, which
prevents an error message when U-Boot's USB stack comes up, and allows
using this port in host mode.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At present we compile commands into U-Boot SPL even though they cannot
be used. This wastes space. Adjust the condition to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_MULTIPLEXER defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
ROCK 5B is a Rockchip RK3588 based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x HDMI output, 1x HDMI input
Ethernet port
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 54mm
Kernel commits:
a1d3281450ab ("arm64: dts: rockchip: Add rock-5b board")
6fb13f888f2a ("arm64: dts: rockchip: Update sdhci alias for rock-5b")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The cpuid on RK3568 is located at 0xa instead of 0x7 as all other SoCs.
Add and use a CFG_CPUID_OFFSET to define this offset.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
Boot log for the record,
DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0x6
CH0 RX Vref:31.7%, TX Vref:21.8%,21.8%
CH1 RX Vref:30.7%, TX Vref:22.8%,23.8%
CH2 RX Vref:30.7%, TX Vref:22.8%,22.8%
CH3 RX Vref:30.7%, TX Vref:21.8%,21.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Trying to boot from MMC1
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-391-g856309329:derrick.huang
NOTICE: BL31: Built : 14:15:50, Jul 18 2022
INFO: ext 32k is not valid
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Model: Edgeble Neu6A IO Board
DRAM: 7.5 GiB (effective 3.7 GiB)
Core: 71 devices, 15 uclasses, devicetree: separate
MMC: mmc@fe2c0000: 0
Loading Environment from nowhere... OK
In: serial@feb50000
Out: serial@feb50000
Err: serial@feb50000
Model: Edgeble Neu6A IO Board
Net: No ethernet found.
Hit any key to stop autoboot: 0
=>
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip RK3588 is a ARM-based SoC with quad-core Cortex-A76
and quad-core Cortex-A55 including NEON and GPU, 6TOPS NPU,
Mali-G610 MP4, HDMI Out, HDMI In, DP, eDP, MIPI DSI, MIPI CSI2,
LPDDR4/4X/5, eMMC5.1, SD3.0/MMC4.5, USB OTG 3.0, Type-C, USB 2.0,
PCIe 3.0, SATA 3, Ethernet, SDIO3.0 I2C, UART, SPI, GPIO and PWM.
Add arch core support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add the dt-bindings header for the Rockchip RK3588, that gets
shared between the clock controller and the clock references
in the dts.
commit <f204a60e545c> ("dt-bindings: clock: add rk3588 clock
definitions")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rockchip,vop2.h from linux-next, and the last commit is
commit <604be85547ce> ("drm/rockchip: Add VOP2 driver")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add default memory addresses for kernel_comp_addr_r and kernel_comp_size
to enable booting from a compressed kernel image. This area is temporarily
used to decompress the kernel image on-the-fly.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add an implementation of this, moving the common call to tpm_init() up
into the common API implementation.
Add a test.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
As described in [0] if a command requires use of an untested algorithm
or functional module, the TPM performs the test and then completes the
command actions.
Since we don't check for TPM_RC_NEEDS_TEST (which is the return code of
the TPM in that case) and even if we would, it would complicate our TPM
code for no apparent reason, add a wrapper function that performs both
the selftest and the startup sequence of the TPM.
It's worth noting that this is implemented on TPMv2.0. The code for
1.2 would look similar, but I don't have a device available to test.
[0]
https://trustedcomputinggroup.org/wp-content/uploads/TPM-Rev-2.0-Part-1-Architecture-01.07-2014-03-13.pdf
§12.3 Self-test modes
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Move the environment to an easily editable text file in the boot
partition
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Measures the DTB passed to the EFI application upon new boolean config
switch CONFIG_EFI_TCG2_PROTOCOL_MEASURE_DTB. For platforms where the
content of the DTB passed to the OS can change across reboots, there is
not point measuring it hence the config switch to allow platform to not
embed this feature.
Co-developed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The current ae350-related defconfigs could also
support newer Andes CPU IP, so modify the names of CPU
from ax25 to andesv5, and board name from ax25-ae350 to ae350.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add a CONFIG option to deal with this automatically, printing a warning
when U-Boot starts up. This can be useful if the device tree comes from
another project.
We will maintain this through the 2023.07 release, providing 6 months
for people to notice.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 4:
Acked-by: Michal Simek <michal.simek@amd.com>
Synology DS116 is a NAS based on Marvell Armada 385 SoC.
Board Specification:
- Marvel MV88F6820 Dual Core at 1.8GHz
- 1 GiB DDR3 RAM
- 8MB Macronix mx25l6405d SPI flash
- I2C
- 2x USB 3.0
- 1x GBE LAN port (PHY: Marvell 88E1510)
- 1x SATA (6 Gbps)
- 3x LED
- PIC16F1829 (connected to uart1)
- GPIO fan
- serial console
Note that this patch depends on the add-support for Thecus N2350 patch:
https://patchwork.ozlabs.org/project/uboot/patch/20230201231306.7010-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
This contains various fixes and small features. I've included a reset patch as
well since it was in the same series as a clock patch.
-----BEGIN PGP SIGNATURE-----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=+n5i
-----END PGP SIGNATURE-----
Merge tag 'clk-2023.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-clk
Clock changes for 2023.04-rc1
This contains various fixes and small features. I've included a reset patch as
well since it was in the same series as a clock patch.
- A fix for a long standing bug that has been exposed by commit
50128aeb0f ("cyclic: get rid of cyclic_init()") preventing 8xx boards
from booting since u-boot 2023.01
- A GPIO driver for powerpc 8xx chip
- Fixup for powerpc 8xx SPI driver
- A new powerpc 8xx board
- The two devices having that board.
This allows devm_reset_control_get(dev, NULL) to work and get the first
reset control, which is common in code ported from Linux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230122000252.53642-2-samuel@sholland.org
This allows devm_clock_get(dev, NULL) to work and get the first clock,
which is common in code ported from Linux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230122000252.53642-1-samuel@sholland.org
Given that the compiler adds two function calls into each function, the
current spacing is overkill. Drop it down to 16 bytes per function, which
is still plenty. This saves some space in the trace buffer.
Also move the calculation into a function, so it is common code. Add a
check for gd->mon_len being unset, which breaks tracing.
Signed-off-by: Simon Glass <sjg@chromium.org>
It seems better to put the TEXT_BASE value in the file header rather than
in an entry record. While it is true that there is a separate base for
pre-relocation, this can be handled by using offsets in the file.
It is useful to have a version number in case we need to change the trace
format again.
Update the header to make these changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tracing is typically enabled by the time driver model starts up, so there
is no point in adding a 'notrace' to the timer-init function. However,
once the driver model timer is enabled, we do need to be able to access
the timer's private data when reading the timer, so add it to the core
function needed for that.
Update the function's documentation while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds a new board from CS GROUP. The board is called
MCR3000_2G, and has a CPU board called CMPC885.
That CPU board is shared with another equipment that will
be added in a later patch.
That board stores Ethernet MAC addresses in an EEPROM which
is accessed using SPI bus.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
Both U-boot and Linux kernel have grown over the last releases
and don't fit anymore in the 2M EPROM of the board.
So, rework the setup to allow storing the Linux kernel image
on the UBIFS NAND Flash.
Also add support to FIT images as this is what the Linux kernel
look like nowadays.
Also increase CFG_SYS_BOOTMAPSZ to 32Mbytes and define
CONFIG_SYS_BOOTM_LEN with the same value, otherwise it defaults
to 8M which is not sufficient anymore with nowadays Linux kernels.
And set the netmask to 255.255.255.0 as a class C address is used.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
We can move all of the environment changes to come
from CONFIG_EXTRA_ENV_TEXT.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Documentation:
* Provide page with links to talks on U-Boot
UEFI:
* Enable CTRL+S to save the boot order in eficonfig command
* Run attribute check for QueryVariableInfo() only for the file store
* Bug fixes
Others:
* Improve output formatting of the coninfo command
-----BEGIN PGP SIGNATURE-----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=HVHT
-----END PGP SIGNATURE-----
Merge tag 'efi-2023-04-rc2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2023-04-rc2
Documentation:
* Provide page with links to talks on U-Boot
UEFI:
* Enable CTRL+S to save the boot order in eficonfig command
* Run attribute check for QueryVariableInfo() only for the file store
* Bug fixes
Others:
* Improve output formatting of the coninfo command
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 10 Feb 2023 12:15:45 PM EST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <xypron.glpk@gmx.de>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
Linux event code must be used in input devices, using buttons.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use standard pinconf drive-strength values from Linux DT bindings rather
than ones based on custom u-boot header. These changes are in direction
to make u-boot DTs for Qcom SoCs to be compatible with standard Linux
DT bindings.
Also, add support for pinconf bias-pull-up.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Boards may set networking variables programmatically, thus may have
CONFIG_NET on but CONFIG_CMD_NET off. The IOT2050 is an example.
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_TARGET_MX6UL_9X9_EVK defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 12 usages of this option to the non-SPL form, since there is
no SPL_SANDBOX_CLK_CCF defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_IMX8MN_BEACON_2GB_LPDDR defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
U-Boot provides multiple EFI applications. The entry point is called
efi_main(). Provide a definition for this function. This avoids
build warnings like
lib/efi_loader/initrddump.c:468:21: warning:
no previous prototype for ‘efi_main’ [-Wmissing-prototypes]
468 | efi_status_t EFIAPI efi_main(efi_handle_t image_handle,
| ^~~~~~~~
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The UEFI specification defines filed UnicodeChar as CHAR16. We use
u16 for CHAR16 throughout our code. The change fixes the following errors:
lib/efi_loader/initrddump.c: In function ‘efi_input’:
lib/efi_loader/initrddump.c:218:38: warning:
comparison is always false due to limited range of data type
[-Wtype-limits]
218 | if (key.unicode_char >= 0xD800 && key.unicode_char <= 0xDBFF)
| ^~
lib/efi_loader/initrddump.c:218:68: warning:
comparison is always true due to limited range of data type
[-Wtype-limits]
218 | if (key.unicode_char >= 0xD800 && key.unicode_char <= 0xDBFF)
| ^~
Fixes: 867a6ac86d ("efi: Add start-up library code")
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
eficonfig_append_menu_entryi() accepts the number of entries
less than or equal to EFICONFIG_ENTRY_NUM_MAX.
EFICONFIG_ENTRY_NUM_MAX is currently set as INT_MAX, so
the invalid menu count check(efi_menu->count > EFICONFIG_ENTRY_NUM_MAX)
in eficonfig_process_common() is always false.
This commit sets EFICONFIG_ENTRY_NUM_MAX to (INT_MAX - 1).
Reported-by: Coverity (CID 435659)
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The change boot order menu in eficonfig can have at most INT_MAX lines
and it is troublesome to scroll down to the "Save" entry.
This commit assigns CTRL+S to save the boot order.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Current U-Boot implements 64-bit boundary for efi_guid_t structure.
It follows the UEFI specification, page 21 of the UEFI Specification v2.10
says about EFI_GUID:
128-bit buffer containing a unique identifier value. Unless
otherwise specified, aligned on a 64-bit boundary.
On the other hand, page 163 of the UEFI specification v2.10 and
EDK2 reference implementation both define EFI_GUID as
struct { u32 a; u16; b; u16 c; u8 d[8]; }; and so the implied
alignment is 32-bit not 64-bit like U-Boot efi_guid_t.
Due to this alignment difference, EDK2 application "CapsuleApp.efi -P"
does not work as expected.
This calls EFI_FIRMWARE_MANAGEMENT_PROTOCOL.GetImageInfo()
and dump the EFI_FIRMWARE_IMAGE_DESCRIPTOR structure,
offsetof(EFI_FIRMWARE_IMAGE_DESCRIPTOR, ImageTypeId) is different,
8 in U-Boot and 4 in EDK2(CapsuleApp.efi).
Here is the wrong EFI_GUID dump.
wrong dump : ImageTypeId - 00000000-7D83-058B-D550-474CA19560D8
expected : ImageTypeId - 058B7D83-50D5-4C47-A195-60D86AD341C4
EFI_FIRMWARE_IMAGE_DESCRIPTOR structure is defined in UEFI specification:
typedef struct {
UINT8 ImageIndex;
EFI_GUID ImageTypeId;
UINT64 ImageId
<snip>
} EFI_FIRMWARE_IMAGE_DESCRIPTOR;
There was the relevant patch for linux kernel to use 32-bit alignment
for efi_guid_t [1].
U-Boot should get aligned to EDK2 reference implementation and
linux kernel.
Due to this alignment change, efi_hii_ref structure in include/efi_api.h
is affected, but it is not used in the current U-Boot code.
[1] https://lore.kernel.org/all/20190202094119.13230-5-ard.biesheuvel@linaro.org/
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This converts 8 usages of this option to the non-SPL form, since there is
no SPL_CMD_USB defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_CMD_SF defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_CMD_SCSI defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_CMD_NVME defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 6 usages of this option to the non-SPL form, since there is
no SPL_CMD_MMC defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_ERASEENV defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_BCB defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
as Tom suggested get rid of CFG_EXTRA_ENV_SETTINGS and
enable CONFIG_ENV_SOURCE_FILE and use text file
board/socrates/socrates.env
which contains the default environment. While at it,
cleanup the default Environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is not used and appears to be associated with the faraday board which
has been removed. Drop the driver and Kconfig options.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are not used. Drop the drivers and Kconfig option. Also drop an
old declaration in the netdev.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used since this commit:
76386d6195 arm: Remove cm_t35 board
Drop the driver and Kconfig option.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used since this commit:
570c3dcfc1 arm: Remove spear600 boards and the rest of SPEAr support
Drop the driver and Kconfig option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
This is not used since this commit:
8d1e3cb140 powerpc: mpc83xx: remove MPC8360ERDK, EMPC8360EMDS support
Drop the driver and Kconfig option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-By: Michael Trimarchi <michael@amarulasolutions.com>
Add a command to load SEAMA (Seattle Image), a NAND flash
on-flash storage format.
This type of flash image is found in some D-Link routers such
as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, DIR890L and
DCH-M225, as well as in WD and NEC routers on the ath79
(MIPS), Broadcom BCM53xx, and RAMIPS platforms.
This U-Boot command will read and decode a SEAMA image from
raw NAND flash on any platform. As it is always using big endian
format for the data decoding is always necessary on platforms
such as ARM.
The command is needed to read a SEAMA-encoded boot image on the
D-Link DIR-890L router for boot from NAND flash in an upcoming
port of U-Boot to the Broadcom Northstar (BCM4709, BCM53xx)
architecture.
A basic test and documentation is added as well. The test must
be run on a target with NAND flash support and at least one
resident SEAMA image in flash.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop use of the distro scripts and use standard boot instead.
Enable BOOTDEV_FULL just for convenience, although this does add quite a
bit to the size.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is currently in the cmd/ file but we want to call it from a driver.
Move it into a common place. Tidy up the header-file order while we are
here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to log things related to filesystems. Add a new
category and place it at the top of one of the FAT files.
Signed-off-by: Simon Glass <sjg@chromium.org>
This family of platforms typically has a USB port, and so attempting to
boot from it, and making it first, will provide a better overall user
experience.
Signed-off-by: Tom Rini <trini@konsulko.com>
we need to set initrd_high to get fitimage booting.
Without, U-Boot drops when booting fitimage:
ERROR: Failed to allocate 0x59a0b6 bytes below 0x800000.
ramdisk - allocation error
bootm - boot application image from memory
Signed-off-by: Heiko Schocher <hs@denx.de>
setup MTD partitioning through mtdparts variable
and set it to:
mtdparts=fe0000000.nor:13312k(system1),13312k(system2),5120k(data),128k(env),128k(env-red),768k(u-boot)
and pass this to linux per kernel commandline.
Signed-off-by: Heiko Schocher <hs@denx.de>
There are no differences for the different 832x targets we have in
the header defined with SYS_CONFIG_NAME. So we can join the five
headers to a single file.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Next step to get rid of the header files in icnlude/configs. Move
most of the defines to km83xx.c directly. Some remaining defines
which should go to Kconfig are moved to km-mpc83xx.h for now.
Also remove some unused defines and move one define to powerpc.env
as we only need it there.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Use .env file for setting board related environment variables,
in place of am62x_evm.h file. Except for BOOTENV settings, as
config_distro_boot.env file doesn't exist.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Required as Elf_Sym in tools/prelink-riscv.inc. I assume people have
been using an OS-supplied elf.h, but macOS doesn't have that.
Taken from
https://github.com/torvalds/linux/blob/v6.1/include/uapi/linux/elf.h
Signed-off-by: KaDiWa <kalle.wachsmuth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ofnode_decode_display_timing supports reading timing parameters from
subnode of display-timings node, for displays supporting multiple
resolution, in case if a display supports single resolution, it fails
reading directly from display-timings node, to support it
ofnode_decode_panel_timing is added.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This moves over the PMIC power init to DM and the associated i2c and
regulator bits.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Commands "ping6" and "tftpboot ... -ipv6" did not work on ARM because
machine code expects 4-byte alignment and some structures from net6.h
are not aligned in memory.
Fix by adding __packed, since it is already used in this file.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Enable TIMER and TEGRA_TIMER for TEGRA_ARMV7_COMMON and TEGRA210.
Additionally enable SPL_TIMER if build as SPL part and drop
deprecated configs from common header.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom <twarren@nvidia.com>
Pick R-Car Gen3 R8A77961 M3W+ power domain header from Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Update commit message
Synchronize R-Car device trees with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
The following script has been used for the synchronization:
$ for i in $(cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) ; do
if [ -e /linux-2.6/arch/arm64/boot/dts/renesas/$i ] ; then
cp /linux-2.6/arch/arm64/boot/dts/renesas/$i arch/arm/dts/ ;
elif [ -e /linux-2.6/arch/arm/boot/dts/$i ] ; then
cp /linux-2.6/arch/arm/boot/dts/$i arch/arm/dts/
else
echo "NOT FOUND: $i"
fi
done
$ git add $( ( cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) | tr " " "\n" | sed 's@^@arch/arm/dts/@g' )
Move the include/dt-bindings/{clk,clock}/versaclock.h header used by
the renesas boards to match Linux 6.1.y as well.
Keep arch/arm/dts/r8a774c0-u-boot.dtsi sdhi3 node as it is now used
by the arch/arm/dts/r8a774c0-cat874.dts board.
Pick s@spi-flash@flash@ change in arch/arm/dts/r8a779a0-falcon-u-boot.dts
from "ARM: dts: Synchronize R-Car V3U DTs with Linux 5.18.3" .
Adjust R8A77990 Ebisu CONFIG_SYS_MMC_ENV_DEV from 2 to 0 to reflect
the card enumeration in ebisu.dtsi /aliases DT node .
Adjust R8A7795 and R8A7796 ULCB CONFIG_SYS_MMC_ENV_DEV from 1 to 0 to
reflect the card enumeration in ulcb.dtsi /aliases DT node .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> # r8a779a0-falcon-u-boot.dts
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> # r8a779a0-falcon-u-boot.dts
Synchronize R-Car device tree headers with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
This is only a copyright and SPDX identifier update, no
functional change.
The following script has been used for the synchronization:
$ for i in $(cd include/dt-bindings/clock/ ; ls -1 r8a*) ; do cp /linux-2.6/include/dt-bindings/clock/$i include/dt-bindings/clock/ ; done
$ for i in $(cd include/dt-bindings/power/ ; ls -1 r8a*) ; do cp /linux-2.6/include/dt-bindings/power/$i include/dt-bindings/power/ ; done
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The HiFive Unmatched board has a M2 slot for NVME and a PCIe slot that
can also be used for NVME. Enable support for a second NVME device, so
that software RAID-1 configurations can be supported at the u-boot
level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The 'commit 864ac2cf38 ("board: imx8mp: Add Engicam
i.Core MX8M Plus EDIMM2.2 Starter Kit")' has changed the imx8mp evk ram
settings from 6GB ram to 2GB.
This changeset reverts the above change.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reported-by : Peter Bergin <peter@berginkonsult.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Cleanup some dangling comments left by automated migration
processes that are no longer value.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The highest register on ACT8846 is 0xf5, so set the number of registers
to 0xf6, ensuring that the pmic read/write commands are able to access
all of the supported registers (and many that are not valid, since the
register space is quite sparse).
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
HS400 is indicated in bit63 of capability register in few IP's.
Add a quirk to check this and add HS400 to host capabilities.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Check if the low level driver supports config_dll callback function and
call it if it does. Call with dll disable before calling set_clock and
with dll enable after it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Add more capable "bkops" command which allows enabling and disabling both
manual and automatic bkops. The existing 'mmc bkops-enable' subcommand is
poorly named to cover all the possibilities, hence the new-ish subcommand.
Note that both commands are wrappers around the same common code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken
directly from Linux 6.2-rc3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
The implementation is taken almost verbatim from Linux commit
2364a64d0673f ("regulator: pca9450: Make warm reset on WDOG_B assertion")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add M4 boot environment functions for reference.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Update the distro config env memory layout for the Apalis iMX8 aka
QuadMax:
- kernel_comp_addr_r=0xf0000000 temporary area for uncompressing (ie FIT
images or Image.gz booted using booti)
- kernel_comp_size=0x08000000
- loadaddr=0x95400000 avoiding any reserved areas located before that
- fdt_addr_r = loadaddr + 128MB - allows for 128MB kernel
- scriptaddr = fdt_addr_r + 512KB - allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB - allows for 512KB script
Basic idea of memory layout taken from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout"). However, moved past
any reserved areas to avoid any kind of conflicts.
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Remove obsolete net USB start.
While at it also add a comment about enabling distro-boot.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Remove obsolete SDHC related config defines. Nowadays, all SDHC related
hardware configuration comes from the device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The distroboot script system scans boot_scripts variable and
try to find and use to boot each script name mentioned there.
Setting global variable "script" breaks this general mechanism
of searching and running a distro boot script.
Remove global variables "script" to fix working the general
distro boot script mechanism.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Implement PCB version and SoC variant handling which automatically loads
the correct device tree for the Linux kernel.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
First, to quote the author:
This series adds support for the PCIe controller found on Apple M1 and
M2 machines and enables support for PCIe XHCI controllers. This makes
the type-A USB ports on the M1 Mac mini work. Since the use of Apples
DART IOMMU is mandatory (these PCIe DARTs don't support bypass mode),
this adds DMA mapping operations to the IOMMU uclass and implements
them for the Apple DART. It modifies the XHCI driver code to go map
DMA buffers through the IOMMU if there is one. Since the M1 Mac mini
now has two types of XHCI controllers with different number of ports
(2 for the DWC3 controllers, 8 for the Fresco Logic PCIe controller)
this uncovered an issue in with the way the hub descriptor is
implemented in the XHCI driver.
Second, Mark also fixes some Apple-specific instances of
CONFIG_IS_ENABLED that should be IS_ENABLED.
Documentation:
* Improve the sl-mx8mm documenation
* Clean up README, move some section to HTML
* Man-pages for the mtime and sleep command
* Description of reducible builds
* Document dynamic event handlers
UEFI:
* Support scrolling in eficonfig command
Other:
* fix mtest on 64 bit systems
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmPUIOwACgkQxIHbvCwF
GsR+txAAhrFDZcQrXpdtaP0ywx6T7zdrbEjYItywDTY2Luun9EAcLI/UUbBwQjxL
Mumou2umY1ff+HqV8eCYA9UyVm5ztg8vpJo4oDMiUlS5o4dHLSJ1CUvsl4r25I8J
NfGyE/iyRyHhDanjGo1gGnRbeXnz4pigtEXa9XOcaSlFezV2UeXWw8LWSo0iTQK+
94+yJsCe+ZIOfpRX20trPb2VtbDPWHIjo+cb+HG3xdgUvL5kUZR/9NvG3npshJBy
lcclRHc2jL405GGuZGtzKDNigkLBQn1NhA8NluD+SATXQnWdg2zMyc15D6UV2V3u
82N33eNr/vobRtvt5cSVm7IP91PFAxNkA/rPRTShOluSa5MCZSDBF8esKOv1OngK
HQLHEvV80H6qU6cWsG1L7INc2kSTRO71vDcsASnfh4gGTHwczOUUEo3oeiaEy5HA
m6U02ymVdtXWuzA0XbrhbjGXHUp9TthdZT2UKDxGFrfPFO+gEtyVeINTBYgNkopc
inqHdV0eDyTVl24TcimVoEEt/16W9MYa9K+hu0FLHshRR0mpRDlhC058SwRseZCL
6qfuqmF5W0y5vFTWXPAiN1HmyusklTl3XIMrV/LX1bKJBZdOB71V+9OMbRirqiWS
a7H05IPYili4l/1iSEoPRsxTP+rWcXKP21AAjIk1CtXW9OeOu8w=
=FY9O
-----END PGP SIGNATURE-----
Merge tag 'efi-2023-04-rc1-3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2023-04-rc1-3
Documentation:
* Improve the sl-mx8mm documenation
* Clean up README, move some section to HTML
* Man-pages for the mtime and sleep command
* Description of reducible builds
* Document dynamic event handlers
UEFI:
* Support scrolling in eficonfig command
Other:
* fix mtest on 64 bit systems
When a system has multiple XHCI controllers, some of the
properties described in the descriptor of the root hub (such as
the number of ports) might differ between controllers. Fix this
by switching from a single global hub descriptor to a hub
descriptor per controller.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
An XHCI controller that sits behind an IOMMU needs to map and unmap
its memory buffers to do DMA. Implement this by inroducing new
xhci_dma_map() and xhci_dma_unmap() helper functions. The
xhci_dma_map() function replaces the existing xhci_virt_to_bus()
function in the sense that it returns the bus address in the case
of simple address translation in the absence of an IOMMU. The
xhci_bus_to_virt() function is eliminated by storing the CPU
address of the allocated scratchpad memory in struct xhci_ctrl.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
In order to support IOMMUs in non-bypass mode we need device ops
to map and unmap DMA memory. The map operation enters a mapping
for a region specified by CPU address and size into the translation
table of the IOMMU and returns a DMA address suitable for
programming the device to do DMA. The unmap operation removes
this mapping from the translation table of the IOMMU.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Now that single defconfig shall be used for booting J721S2 EVM and
AM68 SK, the default device tree will not work for selecting dtb for
kernel. Update the findfdt env to select right dtb based on
board_name env variable.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Current eficonfig has the maximum number of menu entries and
it is 99. If there are more EFI load options and files in the
system, eficonfig can not handle it.
This commit increases this maximum number of menu entries
to INT_MAX.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The current eficonfig menu does not support vertical scroll,
so it can not display the menu entries greater than
the console row size.
This commit add the vertial scroll support.
The console size is retrieved by
SIMPLE_TEXT_OUTPUT_PROTOCOL.QueryMode() service, then
calculates the row size for menu entry by subtracting
menu header and description row size from the console row size.
"start" and "end" are added in the efimenu structure.
"start" keeps the menu entry index at the top, "end" keeps
the bottom menu entry index. item_data_print() menu function
only draws the menu entry between "start" and "end".
This commit also fixes the issue that "Save" and "Quit"
entries can be moved by BKEY_PLUS in change boot order menu.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Current change boot order implementation does not call
eficonfig_process_common() and call own menu functions
for display_statusline, item_data_print and item_choice.
Change boot order functionality should call
eficonfig_process_common() to improve maintenanceability.
This commit is a preparation to remove the change boot
order specific implementation. The menu functions
(display_statusline, item_data_print and item_choice) are
added as argument of eficonfig_process_common().
The menu description string displayed at the bottom of
the menu is also added as argument.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The actual function being documented is jump_to_image_optee(), not
jump_to_image_linux().
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY9PmzwAKCRDKSWXLKUoM
IYWxAJwNgiXtFT17pBy+1M0JvSWgyvWF3QCfTQG2Krnw0+d65PF5A7UFTDL7SZM=
=cMrc
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx chnages for v2023.04-rc1
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
Infineon S25FS256T is 256Mbit Quad SPI NOR flash. The key features and
differences comparing to other Spansion/Cypress flash familes are:
- 4-byte address mode by factory default
- Quad mode is enabled by factory default
- Supports mixture of 128KB and 64KB sectors by OTP configuration
(this patch supports uniform 128KB only)
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cypress defines two flavors of configuration registers, volatile and
non volatile, and both use the same bit fields. Rename the bitfields in
the configuration registers so that they can be used for both flavors.
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
CFR5[6] is reserved bit and must be always 1. Set it to comply with flash
requirements. While fixing SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN definition,
stop using magic numbers and describe the missing bit fields in CFR5
register. This is useful for both readability and future possible addition
of Octal STR mode support.
Fixes: ea9a22f7e7 ("mtd: spi-nor-core: Add support for Cypress Semper flash")
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This contains some fixes, and the first bunch of some clean up patches
to get rid of legacy GPIO and PMIC code.
Highlight is the DM AXP PMIC driver, which is required to convert some
drivers over to use DM regulators, and also is required to get rid
of some less optimal PMIC setup code in Trusted Firmware. This isn't
enabled by any defconfig yet, but can be enabled manually and works. For
the full glory some patches are still missing, and this requires more
testing, which would be simpler if the core code is upstream.
The commit eaf6ea6a1d ("Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using
system-constants.h") moved custom init stack pointer address to Kconfig
which ends up in situation that xilinx_versal_mini_qspi.h is not
needed anymore. That's why remove the file and move defconfigs directly to
xilinx_versal_mini.h configuration.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/2d7276ab8d4cb1d245b64287fb59c79325513f22.1674041200.git.michal.simek@amd.com
The commit eaf6ea6a1d ("Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using
system-constants.h") moved custom init stack pointer address to Kconfig
which ends up in situation that xilinx_zynqmp_mini_emmc/qspi.h are not
needed anymore. That's why remove files and move defconfigs directly to
xilinx_zynqmp_mini.h configuration.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/61ae40cf63aabd08adb386c870d3392b0b606fc9.1674040373.git.michal.simek@amd.com
Drop the use of scripts and rely on standard boot for all operation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a way to record the bootdevs used when scanning for bootflows. This is
useful for testing.
Enable this only with BOOTSTD_FULL and do the same for the progress
reporting.
Re-enable and update the affected tests now that we have this feature.
For bootdev_test_order_default() there is no-longer any support for using
the bootdev aliases to specify an ordering, so drop that part of the test.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not used outside tests. Drop it and rename
bootflow_scan_dev() since it is how we start a scan now.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to support scanning a single label, like 'mmc' or 'usb0'. Add
this feature by plumbing the label through to the iterator, setting a
flag to indicate that only siblings of the initial device should be used.
This means that scanning a bootdev by its name is not supported anymore.
That feature doesn't seem very useful in practice, so it is no great loss.
Add a test for bootdev_find_by_any() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we set up the bootdev order at the start, then scan the
bootdevs one by one.
However this approach cannot be used with hunters, since the bootdevs may
not exist until the hunter is used. Nor can we just run all the hunters at
the start, since that violate's U-Boot's 'lazy init' requirement. It also
increases boot time.
So we need to adjust the algorithm to scan by labels instead. As a first
step, drop the dev_order[] array in favour of a list of labels. Update the
name of bootdev_setup_iter_order() to better reflect what it does.
Update some related comments and log messages. Also disable a few tests
until a later commit where we can use them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function which moves to the next priority to be processed.
This works by storing the current priority in the bootflow iterator. The
logic to set this up is included in a subsequent commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function which moves to the next label in a list of labels. This
allows processing the boot_targets environment variable.
This works using a new label list in the bootflow iterator. The logic to
set this up is included in a subsequent commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to hunt for a bootdev label and find the bootdev produced
by the hunter (or already present).
Add a few extra flags so that we can distinguish between "mmc1", "mmc" and
"1" which all need to be handled differently.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need extensions to be set up before we start trying to boot any of the
bootdevs. Add a new priority before all the others for tht sort of thing.
Also add a 'none' option, so that the first one is not 0.
While we are here, comment enum bootdev_prio_t fully and expand the test
for the 'bootdev hunt' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a flag to control whether hunters are used when scanning for
bootflows. Enable it by default and tidy up the flag comments a little.
Fow now this has no effect, until a future patch enables this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are associated with the ethernet boot device but do not match its
uclass name, so handle them as special cases.
Provide a way to pass flags through with the bootdev so that we know
how to process it. The flags are checked by the bootmeths, to ensure that
only the selected bootmeth is used.
While these both use the network device, they work quite differently. It
is common to run only one of these, or to run PXE before DHCP. Provide
bootflow flags to control which methods are used. Check these in the two
bootmeths so that only the chosen one is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a bootdev for SPI flash so that these devices can be used with
standard boot. It only supports loading a script.
Add a special case for the label, since we want to use "spi", not
"spi_flash".
Enable the new bootdev on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most tests don't want these and they can create a lot of noise. Add a way
to disable them. Use that in tests, with a flag provided to enable them
for tests that need this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Normally the bootmeth driver reads the bootflow from the bootdev, since
it knows the correct way to do it.
However it is easier for some bootdevs to handle this themselves. For
example, reading from SPI flash is quite different from other devices.
Add a way for the bootdev to pass a bootflow to the bootmeth, so that
this can be supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Mention that this function is also used with a NULL block devices to
access files on the host, when using sandbox.
Update the comment on struct bootflow also.
Signed-off-by: Simon Glass <sjg@chromium.org>
This environment variable is supposed to be set so that the script knows
which partition holds the script. Set it before invoking the script.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootmeths provide a way to load a device tree as well as the base
OS image. Add a way to store this in the bootflow. Update the
'bootflow info' command to show this information.
Note that the device tree is not allocated, but instead is stored at
an address provided by an environment variable. This may need to be
adjusted at some point, but for now it works well and fits in with the
existing distro-boot scripts.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present all partitions are scanned, whether marked bootable or not.
Use only bootable partitions, defaulting to partition 1 if none is
found.
Signed-off-by: Simon Glass <sjg@chromium.org>
If a disk has a bootable partition we are expected to use it to locate the
boot files. Add a function to find it.
To test this, update mmc1 to have two paritions, fixing up other tests
accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this must be done by executing the command. Also it involves
fiddling with the environment to determine the correct autoload behaviour.
Ideally it should be possible to run network operations without even
having the command line present (CONFIG_CMDLINE).
For now, add a function to handle DHCP, so it can be called from a bootdev
more easily.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
At present this feature is sandbox-specific. For running tests on boards,
we need a nop version. Add one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to run a bootdev hunter to find bootdevs of a certain type. Add
this to the 'bootdev hunt' command. Test for this are added in a later
patch, since a useful test needs some hunters to work with.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootdevs must be enumerated before they appear. For example, USB
bootdevs are not visible until USB is enumerated.
With standard boot this needs to happen automatically, since we only
want to enumerate a bus if it is needed.
Add a way to define bootdev 'hunters' which can be used to hunt for
bootdevs of a given type. Track which ones have been used and add a
command to list them.
Include a clang work-around which seems to be needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most tests don't want these and can create a lot of noise. Add a way to
disable them. Use that in tests, with a flag provided to enable them for
tests that need this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
For bootstd tests it is seldom useful to have ethernet enabled. Add a way
to disable it, so that ethernet operations like tftpboot do nothing.
Signed-off-by: Simon Glass <sjg@chromium.org>
The code in these functions turns out to often be the same. Add a default
get_bootflow() function and allow the drivers to select it by setting
the method to NULL.
This saves a little code space.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present MMC uses the bootdev_setup_for_dev() function to set up the
bootdev. This is because MMC only has one block-device child, so does not
need to worry about naming of the bootdev.
However this inconsistency with other bootdevs that use block devices is a
bit annoying. The only real reason for it is to have a name like
'mmc0.bootdev' instead of 'mmc0.blk.bootdev'.
Update bootdev_setup_sibling_blk() to drop '.blk' from the name where it
appears, thus removing the only reason to use the bootdev_setup_for_dev().
Switch MMC over to the subling function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than implement this as its own case in build_order(), process the
boot_targets environment variable in the bootstd_get_bootdev_order()
function. This allows build_order() to be simplified.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some environment variables provide a space-separated list of strings. It
is easier to process these when they are broken out into an array of
strings.
Add a utility function to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Subordinate regulator drivers can use this enumerated ID instead of
matching the compatible string again.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When using the USB OTG FEL mode on the Allwinner H616, the BootROM
stores some data at the end of SRAM C. This is also the location where
we place the initial SPL stack, so it will overwrite this data.
We still need the BROM code after running the SPL, so should leave that
area alone.
Interestingly this does not seem to have an adverse effect, I guess on
the "way out" (when we return to FEL after the SPL has run), this data
is not needed by the BROM, for just the trailing end of the USB operation.
However this is still wrong, and we should not clobber BROM data.
Lower the SPL stack address to be situated right below the swap buffers
we use in sunxi-fel: that should be out of the way of everyone else.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is always defined to 5, so use that as the default.
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Prior to commit 9591b63531 ("Convert CONFIG_SYS_NS16550_MEM32 et al to
Kconfig") we had defined CONFIG_SYS_NS16550_REG_SIZE to -1 with
DM_SERIAL such that we would then have a size 0 character array. This
resulted in functionally no padding. The confusion on my part came from
dealing with the constraints around platforms that do not use DM_SERIAL
in SPL/TPL. After Andre Przywara reported that sunxi was broken, I've
re-read the code and comments again and thought on this harder. What we
want I believe is what this patch does now.
If DM_SERIAL is defined for this stage, regardless of
CONFIG_SYS_NS16550_REG_SIZE then we will dynamically handle reg shifts
and 'struct ns16550' needs no padding (which is functionally what
unsigned char foo[0] provides). This is the same case as NS16550_DYNAMIC
and DEBUG_UART. Expand the existing comment here slightly.
Otherwise, we will have CONFIG_SYS_NS16550_REG_SIZE set to a non-zero
value, and handle padding within the struct.
Cc: Simon Glass <sjg@chromium.org>
Cc: Sergei Antonov <saproj@gmail.com>
Cc: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Fixes: 9591b63531 ("Convert CONFIG_SYS_NS16550_MEM32 et al to Kconfig")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Remove some CONFIG symbols and related comments, etc, that are unused
within the code itself at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
UEFI applications call file system functions to determine if a file exists.
The return codes are evaluated to show appropriate messages.
U-Boot's file system layer should not interfere with the output.
Rename file_fat_read_at() to fat_read_file() adjusting the parameter
sequence and names and eliminate the old wrapper function.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmPIpV4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZuqwgA0UpYQEX6/MegzHSCIx3AMT4rCF1Ytitr
LS4Cbvj1Q09Rt9jriW7wAV5AobVPwGf2L5SVcnWv2I9+MmypDIXEe8HIrt2fRFu9
bzn/2GOzXczuXqPFa/CWOUwjvCzTb8Sl9NtRszrP5NvOzuN15x00ZUYaXFO7fgsB
zZMzOKxemwjdtLaox+x+VIJ95HMDEkYrWTAqTPg74CNVSjRbbLNqNq0zqkHB8SnH
ubgphtIKYItTeIXcfIa9V4LeQp0ZitkzSfAibX+nIPCMPg9jbG9MrQQ+VvSZDjnM
y8wa8gFj47Ek+gGNFXMHIpO6tBd83uHRgtf2x+zhcovLELYnZ6fDGw==
=1K6m
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18jan23' of https://source.denx.de/u-boot/custodians/u-boot-dm
convert rockchip to use binman
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
In commit 4963f63fe6 ("image: Use gd->ram_base/_size in
env_get_bootm_size()") the size of the available memory for U-Boot to
use when relocating images, and not otherwise constrained, was changed
to include all known memory banks. In the case of this platform however,
all of the memory known to U-Boot is not also part of the Linux kernel
"lowmem" and so we must use CFG_SYS_BOOTMAPSZ to limit where we relocate
images to. We set a conservative limit of 256MB here to mirror the
previous behavior.
Signed-off-by: Joost van Zwieten <joost@diskos.nl>
[trini: Reword the commit messsage]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the zstd implementation to match Linux zstd 1.5.2 from commit
2aa14b1ab2.
This was motivated by running into decompression corruption issues when
trying to uncompress files compressed with newer versions of zstd. zstd
users also claim significantly improved decompression times with newer
zstd versions which is a side benefit.
Original zstd code was copied from Linux commit 2aa14b1ab2 which is a
custom-built implementation based on zstd 1.3.1. Linux switched to an
implementation that is a copy of the upstream zstd code in Linux commit
e0c1b49f5b, this results in a large code diff. However this should make
future updates easier along with other benefits[1].
This commit is a straight mirror of the Linux zstd code, except to:
- update a few #include that do not translate cleanly
- linux/swab.h -> asm/byteorder.h
- linux/limits.h -> linux/kernel.h
- linux/module.h -> linux/compat.h
- remove assert() from debug.h so it doesn't conflict with u-boot's
assert()
- strip out the compressor code as was done in the previous u-boot zstd
- update existing zstd users to the new Linux zstd API
- change the #define for MEM_STATIC to use INLINE_KEYWORD for codesize
- add a new KConfig option that sets zstd build options to minify code
based on zstd's ZSTD_LIB_MINIFY[2].
These changes were tested by booting a zstd 1.5.2 compressed kernel inside a
FIT. And the squashfs changes by loading a file from zstd compressed squashfs
with sqfsload. buildman was used to compile test other boards and check for
binary bloat, as follows:
> $ buildman -b zstd2 --boards dh_imx6,m53menlo,mvebu_espressobin-88f3720,sandbox,sandbox64,stm32mp15_dhcom_basic,stm32mp15_dhcor_basic,turris_mox,turris_omnia -sS
> Summary of 6 commits for 9 boards (8 threads, 1 job per thread)
> 01: Merge branch '2023-01-10-platform-updates'
> arm: w+ m53menlo dh_imx6
> 02: lib: zstd: update to latest Linux zstd 1.5.2
> aarch64: (for 2/2 boards) all -3186.0 rodata +920.0 text -4106.0
> arm: (for 5/5 boards) all +1254.4 rodata +940.0 text +314.4
> sandbox: (for 2/2 boards) all -4452.0 data -16.0 rodata +640.0 text -5076.0
[1] e0c1b49f5b
[2] f302ad8811/lib/libzstd.mk (L31)
Signed-off-by: Brandon Maier <brandon.maier@collins.com>
[trini: Set ret to -EINVAL for the error of "failed to detect
compressed" to fix warning, drop ZSTD_SRCSIZEHINT_MAX for non-Linux host
tool builds]
Signed-off-by: Tom Rini <trini@konsulko.com>
To quote the author:
So far standard boot lacks a boot menu, although it is possible to create
a rudimentary one using the existing 'bootmenu' command.
Even then, this text-based menu offer only basic functionality and does
not take full advantage of the displays which are common on many devices.
This series provides a 'bootflow menu' command which allows the user to
select from the available bootflows. An attempt is made to show the name
of the available operating systems, by reading more information into the
bootflow. A logo can be read also, where supported, so that this can be
presented to the user when an option is highlighted.
Full use is made of TrueType fonts, if enabled. For cases where only a
serial console is available, it falls back to a simple text-based menu.
All of this is implementing using a new 'expo' construct, a collection of
scenes (like menu screens) which can be navigated by the user to view
information and select options. This is fairly general and should be able
to cope with a wider array of use cases, with less hacking of the menu
code, such as is currently needed for CMD_BOOTEFI_BOOTMGR.
Of course it would be possible to enhance the existing menu rather than
creating a new setup. Instead it seems better to make the existing menu
use expo, if code space permits. It avoids the event-loop problem and
should be more extensible, given its loosely coupled components and use of
IDs instead of pointers. Further motivation is provided in the
documentation.
For now the CLI keypress-decoding code is split out to be used by the new
menu. The key codes defined by menu.h are reused also.
This is of course just a starting point. Some ideas for future work are
included in the documentation.
Create an expo to handle the boot menu. For now this is quite simple, with
just a header, some menu items and a pointer to show the current one.
Signed-off-by: Simon Glass <sjg@chromium.org>
An expo is a way of presenting and collecting information from the
user. It consists of a collection of 'scenes' of which only one is
presented at a time. An expo is typically used to show a boot menu
and allow settings to be changed.
One created, the same expo can be automatically presented in graphical
form using a vidconsole, or in text form on a serial console.
Add an initial implementation of the expo itself. Supports for scenes
and objects is provided later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some operating systems provide a logo in bmp format. Read this in if
present so it can be displayed in the menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the concept of an OS name to the bootflow. This typically includes the
OS name, version and kernel version.
Implement this for the distro and script bootmeths so that it works with
Armbian and older version of Fedora.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support for fonts currently depends on the type of vidconsole in use. Add
two new methods to enumerate fonts and to set the font.
Fix a few other method comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should use the cmd/ directory for commands rather than for common code
used elsewhere in U-Boot. Move the common 'source' code into
image-board.c to achieve this.
The image_source_script() function needs to call run_command_list() so
seems to belong better in the command library. Move and rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Split this functionality out of the 'source' command so it can be used
from another place. For now leave it where it is, but a future patch will
move it out of cmd/
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the return value to save having to pass around a pointer. This also
resolves any ambiguity about what *key contains when the function is
called.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the return value to save having to pass around a pointer. This also
resolves any ambiguity about what *key contains when the function is
called.
Signed-off-by: Simon Glass <sjg@chromium.org>
The behaviour of these two functions is completely undocumented. Add some
notes so the poor, suffering dev can figure out what is going on.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current cread_line() function is very long. It handles the escape
processing inline. The menu command does similar processing but at the
character level, so there is some duplication.
Split the character processing into a new function cli_ch_process() which
processes individual characters and returns the resulting input character,
taking account of escape sequences. It requires the caller to set up and
maintain its state.
Update cread_line() to use this new function.
The only intended functional change is that an invalid escape sequence
does not add invalid/control characters into the input buffer, but instead
discards these.
Signed-off-by: Simon Glass <sjg@chromium.org>
The IRAM on PX30 (or Int_MEM in datasheet) starts at 0xff0e0000 and not
0xff020000 as rightfully stated in the FIXME comment.
Let's fix it so that BROM_BOOTSOURCE_ID_ADDR points to the correct
address for PX30.
Fixes: 46281a76be ("rockchip: add core px30 headers")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
The Pinephone Pro is another device by PINE64. It's closely related
to the Pinebook Pro of which this initial support is derived from.
Specification:
- A variant of the Rockchip RK3399
- A 6 inch 720*1440 DSI display
- Front and rear cameras
- Type-C interface with alt mode display (DP 1.2) and PD charging
- 4GB LPDDR4 RAM
- 128GB eMMC
- mSD card slot
- An AP6255 module for 802.11ac WiFi and Bluetooth 5
- Quectel EG25-G 4G/LTE modem
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
IO board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Rockchip RV1126 is a high-performance vision processor SoC
for IPC/CVR, especially for AI related application.
Add arch core support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change-Id: I22fde40ec375e3c6aba39808abf252edc45d4b04
Add power-domain header for RV1126 SoC from description in TRM.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the dt-bindings header for the Rockchip RV1126, that gets shared
between the clock controller and the clock references in the dts.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Key data is never written so the parameter can be const, which allows
putting fixed keys in .rodata.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove non-existent parameter 'n' from function description.
Fixes: 7a9b366cd9 ("lib: add function u16_strcasecmp()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The gpio_hog_probe_all() functionality can be perfectly well replaced by
DM_FLAG_PROBE_AFTER_BIND DM flag, which would trigger .probe() callback
of each GPIO hog driver instance after .bind() and thus configure the
hogged GPIO accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The assignment of block device nodes in Linux is not deterministic by
default, i.e. a newly added eMMC controller or other block device can
change the assignment of /dev/mmcblkN (or other block device node like
e.g. /dev/sdXy) and prevent the system from picking the correct block
device for root filesystem in case the root filesystem is specified on
kernel command line using 'root=/dev/mmcblkNpM' (or 'root=/dev/sdXy'
etc.).
One way out is to derive PARTUUID in U-Boot, which is unique identifier
of a partition, and pass that as root=PARTUUID=<partuuid> to Linux via
kernel command line. Linux would then find the partition using PARTUUID,
no matter on which block device the partition resides and which node was
assigned to that block device.
Derive the PARTUUID before scanning for extlinux presence and assign it
into distro_bootpart_uuid environment variable, which can then be used
in extlinux.conf kernel command line specifier.
Note that it is not possible to do this in scan_dev_for_extlinux script
because this script is called from scan_dev_for_boot script, which is
called for both block devices as well as UBI volumes, and we can not
derive PARTUUID for UBI volumes.
Signed-off-by: Marek Vasut <marex@denx.de>
The fs_loader device is used to pull in settings via the chosen node.
However, there was no library function for this, so arria10 was doing it
explicitly. This function subsumes that, and uses ofnode_get_chosen_node
instead of navigating the device tree directly. Because fs_loader pulls
its config from the environment by default, it's fine to create a device
with nothing backing it at all. Doing this allows enabling
CONFIG_FS_LOADER without needing to modify the device tree.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a test which validates that exit from environment script works as
expected, including return value propagation and clipping to positive
integers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
This adds the UUU UCmd functionality as an OEM command. While the
fastboot tool allows sending arbitrary commands as long as they are
prefixed with "oem". This allows running generic U-Boot commands over
fastboot without UUU, which is especially useful when not using USB.
This is really the route we should have gone in the first place when
adding these commands.
While we're here, clean up the UUU Kconfig a bit.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Much of the fastboot code predates the introduction of Kconfig and
has quite a few #ifdefs in it which is unnecessary now that we can use
IS_ENABLED() et al.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3l
It was temporary disabled due to problem with boot.
Issue was fixed in
commit f5ed6c9ccf ("uart: sdm845: Fix debug UART pinmux")
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
In order to maintain the chain of trust, each stage of the boot process
will first authenticate each binary it loads before continuing. To
extend this to the kernal and its dtbs we can package the kernal and
its dtbs into another fitImage for Uboot to authenticate and extend the
chain of trust all the way to the kernel.
When 'boot_fit' is set, indicating we're using the secure bootflow, look
for and authenticate the kernel's fitImage.
Signed-off-by: Judith Mendez <jm@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
We're currently using CONFIG_BOOTCOMMAND to run custom boot scripts to
jump into linux. While this works, let's begin the transition to more
distribution friendly jumps to linux by enabling distro_bootcmd.
Convert the custom bootcmd to a distro_bootcmd
Signed-off-by: Judith Mendez <jm@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
TI boards use a custom (though faily common to TI boards) mechanism for
booting Linux. We would like to use the "distroboot" approach.
Enable distroboot as a further option to use for booting on am625 should
the existing options fail.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
The new JetHub D1+ has a microSD slot. Add rescue boot from microSD
Signed-off-by: Viacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221222093358.204520-1-adeep@lexina.in
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
There are currently no platform that are both CONFIG_SYS_NS16550_MEM32
and not (per how the logic was prior to being broken in 0478dac62a
("kbuild: Remove uncmd_spl logic")) enabled in CONFIG_DM_SERIAL. We drop
this line out now so that platforms which do use
CONFIG_SYS_NS16550_MEM32 and depending on stage may or may not have
DM_SERIAL set.
Fixes: 0478dac62a ("kbuild: Remove uncmd_spl logic")
Reported-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> #on Ringneck PX30, Puma RK3399
- rawnand: omap_gpmc: driver model support
-----BEGIN PGP SIGNATURE-----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=Agfn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230108' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash into next
Pull request for u-boot-nand-20230108
- rawnand: omap_gpmc: driver model support
The "SCRIPT FAILED" string is copied from scan_dev_for_scripts script,
update it so it prints "EXTLINUX FAILED" instead in scan_dev_for_extlinux
script.
Signed-off-by: Marek Vasut <marex@denx.de>
Support u-boot driver model. We still retain
support legacy way of doing things if ELM_BASE
is defined in <asm/arch/hardware.h>
We could completely get rid of that if all
platforms defining ELM_BASE get rid of that definition
and enable CONFIG_SYS_NAND_SELF_INIT and are verified
to work.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/all/20221220102203.52398-9-rogerq@kernel.org
Link: https://lore.kernel.org/all/CABGWkvrvKiVA_yaDnHJcHEKwc+pEuLdz=i6HQEY0oJQvohCUsw@mail.gmail.com
On the vexpress_ca9x4 $loadaddr points to a memory area used by the EFI
sub-system. Use the same value as $kernel_addr_r which is safe.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmO2mnEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBAOB/4y7e9y0jdKSWDwMdZj
enXK/U/GREFyuiSdadil0aJl9WfayjwZkh7uHSTj4pi9ApNivfoqsL7WZYpJxhRD
WlpNhs3TZ70i8CgKUosdzcpquAQZUZhg6iV5DCObrK6yNJRGOXLIwMOd+vw/Xz6/
YTGqzivEDMBuH/9HLuC0m+26PEpff8nenNEjC2k8ssG26ojLz7oCQh2HoHcSgNRc
HkEYlFJ/Le8kM8Ak2F3ebmsfgMTnFrRVwV1BsZa5vO0BrMYgJCORsl7Cnfcw6/2N
LEHG7kwlSorJeETn/gkLiZ+NyqzU+oFH0jGRZ5Ciqg1qcCO3k9yBMgWQzd7nTL6C
5oZA
=Ocdd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.04 cycle:
This feature set includes the new DM-based NAND flash driver (old non-DM
driver is still kept for backwards compatibility), and the move to DM
NAND flash driver for sam9x60ek board. Feature set also includes
devicetree alignment for sama7g5 with Linux, devicetree alignment on USB
with Linux for all boards (sama5, sam9x60), chip id for sama7g5, minor
configs and tweaks.
Upstream linux commit 5994f58977e0.
Add reset bindings for SAMA7G5. At the moment only USB PHYs are
included.
The three reset USB phy's have their ID's mapped from 4 to 6. There are
no USB phy's with ID's numbered from 0 to 3.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Provide constants for the section flags used by binaries.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Per env/common.c, eth_env_get_enetaddr() returns the same return
values as is_valid_ethaddr(), i.e. true if valid, false otherwise.
Per env/common.c, eth_env_set_enetaddr() may return -EEXIST is the
ethaddr is already set. Fix both.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Remove init of UART-clock and UART-reset in arch_cpu_init(). Add DEBUG_UART
to s5p4418_nanopi2_defconfig.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
All uniphier v7 SoCs have cortex-a9 and use cortex-a9 global timer
in a simple implementation. Now DM_TIMER of it is available
on 35751c7f3f ("timer: sti: convert sti-timer to arm a9 global timer"),
so let's switch to it.
The old driver reads the lower 32bits of counter field
and sets the prescaler as 50 with PERIPHCLK(=50MHz),
so the global timer works as a 32-bit 1MHz timer.
The DM_TIMER uses the whole 64bits with no prescaler,
so the global timer works as a 64-bit PERIPHCLK timer.
CONFIG_SYS_HZ_CLOCK is set as the default PERIPHCLK frequency,
if there is no 'clocks' property in devicetree.
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
As discussed previously [1,2], the source command is not safe to use with
verified boot unless there is a key with required = "images" (which has its
own problems). This is because if such a key is absent, signatures are
verified but not required. It is assumed that configuration nodes will
provide the signature. Because the source command does not use
configurations to determine the image to source, effectively no
verification takes place.
To address this, allow specifying configuration nodes. We use the same
syntax as the bootm command (helpfully provided for us by fit_parse_conf).
By default, we first try the default config and then the default image. To
force using a config, # must be present in the command (e.g. `source
$loadaddr#my-conf`). For convenience, the config may be omitted, just like
the address may be (e.g. `source \#`). This also works for images
(`source :` behaves exactly like `source` currently does).
[1] https://lore.kernel.org/u-boot/7d711133-d513-5bcb-52f2-a9dbaa9eeded@prevas.dk/
[2] https://lore.kernel.org/u-boot/042dcb34-f85f-351e-1b0e-513f89005fdd@gmail.com/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fallback for this function so it can be used without regard to
whether FIT_SIGNATURE is enabled or not.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At this point in the conversion there should be no need to have logic to
disable some symbol during the SPL build as all symbols should have an
SPL counterpart.
The main real changes done here are that we now must make proper use of
CONFIG_IS_ENABLED(DM_SERIAL) rather than many of the odd tricks we
developed prior to CONFIG_IS_ENABLED() being available.
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of CONFIG symbols have crept in that are never referenced in
code, so drop them here. Further, we have two symbols being enabled
in headers while already enabled correctly in Kconfig, so these lines
can also be removed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename the CONFIG_POWER_BD71837_I2C_* symbols to not have the CONFIG
prefix and be local to the file they are used in.
Signed-off-by: Tom Rini <trini@konsulko.com>
Perform simple renames of:
CONFIG_WATCHDOG_PRESC to CFG_WATCHDOG_PRESC
CONFIG_WATCHDOG_RC to CFG_WATCHDOG_RC
Signed-off-by: Tom Rini <trini@konsulko.com>
Perform simple renames of:
CONFIG_VSC7385_IMAGE to CFG_VSC7385_IMAGE
CONFIG_VSC7385_IMAGE_SIZE to CFG_VSC7385_IMAGE_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
