This patch simply converts the board to the hwconfig infrastructure.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
fdt_fixup_esdhc() will either disable or enable eSDHC nodes, and
also will fixup clock-frequency property.
Plus, since DR USB and eSDHC are mutually exclusive, we should
only configure the eSDHC if asked through hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for eSDHC on MPC837XERDB boards. The WP
switch doesn't seem to work on RDB boards though, the WP pin is
always asserted (can see the pin state when it's in GPIO mode).
FSL DR USB and FSL eSDHC are mutually exclusive because of pins
multiplexing, so user should specify 'esdhc' or 'dr_usb' options
in the hwconfig environment variable to choose between the
devices.
p.s.
Now we're very close to a monitor len limit (196 bytes left using
gcc-4.2.0), so also increase the monitor len by one sector (64 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Update serial boot DRAM's Internal RAM, vector table and DRAM in
start.S, serial flash's read status command over SPI and NOR
flash.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Now that we have 3 boards for the MPC512x it turns out that they all
use the very same fixed_sdram() code.
This patch factors out this common code into cpu/mpc512x/fixed_sdram.c
and adds a new header file, include/asm-ppc/mpc512x.h, with some
macros, inline functions and prototype definitions specific to MPC512x
systems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
sys_eeprom.c: In function 'do_mac':
sys_eeprom.c:323: warning: dereferencing type-punned pointer will break strict-aliasing rules
sys_eeprom.c: In function 'mac_read_from_eeprom':
sys_eeprom.c:395: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to
CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures
use
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
All drivers need to be converted to CONFIG_NET_MULTI.
This patch converts the dm9000 driver.
Signed-off-by: Thomas Smits <ts.smits@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
We support up to 8 mac addresses in system eeprom, so we define the macro
MAX_NUM_PORTS to limit the mac_count to 8, and update the number of ethxaddr
according to mac_count.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch supports UCC working at RMII mode on PIB board, fixup fdt blob to
support rmii in kernel. It also changes the name of enable_mpc8569mds_qe_mdio to
enalbe_mpc8569mds_qe_uec which is more accurate.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds NAND support to the MPC5121ADS board. Please
note that the image size increased since NAND support didn't
fit in the current image size (256k).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This commit changes the MPC512x code to use I/O accessor calls (i.e.
out_*() and in_*()) instead of using deprecated pointer accesses.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
We rename the board so we use a consistent name in U-Boot and in
Linux. Also, we use this opportunity to move the board into the
Freecale vendor directory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.
Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.
This patch cleans this up - for example:
Before:
=> help dtt
dtt - Digital Thermometer and Thermostat
Usage:
dtt - Read temperature from digital thermometer and thermostat.
After:
=> help dtt
dtt - Read temperature from Digital Thermometer and Thermostat
Usage:
dtt
Signed-off-by: Wolfgang Denk <wd@denx.de>
all arm boards except a few use the same cpu linker script
so move it to cpu/$(CPU)
that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
MPC8569 UART1 signals are muxed with PortF bit[9-12], we need to define
those pins before using UART1.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The BCSR17[7] = 1 will unlock the write protect of FLASH.
The WP# pin only controls the write protect of top/bottom sector,
That is why we can save env, but we can't write the first sector
before the patch.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Currently the clk_adj is 6 (3/4 cycle), The settings will cause
the DDR controller hang at the data init. Change the clk_adj
from 6 to 4 (1/2 cycle), make the memory system stable.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Rename the pci header for FSL HW so we can move some prototypes
in there and stop doing explicit externs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx
* Introduce determine_mp_bootpg() helper. We'll need this to address a
bug introduced in v2009.03 with 86xx MP booting. We have to make sure
to reserve the region of memory used for the MP bootpg() so other
u-boot code doesn't use it.
* Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to
allow cmd_mp.c to build and work. In the future we should look at
implementing all these functions. This could be common w/85xx if we
use spin tables on 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We're missing the board_lmb_reserve definitions that allow
cpu_mp_lmb_reserve to be called; this means that Linux
is free to reallocate reserved pages. Linux currently boots
because we're getting lucky - the page we've reserved is
high enough in memory that it isn't allocated by Linux
while we still need it to be in existence.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A recent gcc added a new unaligned rodata section called '.rodata.str1.1',
which needs to be added the the linker script. Instead of just adding this
one section, we use a wildcard ".rodata*" to get all rodata linker section
gcc has now and might add in the future.
However, '*(.rodata*)' by itself will result in sub-optimal section
ordering. The sections will be sorted by object file, which causes extra
padding between the unaligned rodata.str.1.1 of one object file and the
aligned rodata of the next object file. This is easy to fix by using the
SORT_BY_ALIGNMENT command.
This patch has not be tested one most of the boards modified. Some boards
have a linker script that looks something like this:
*(.text)
. = ALIGN(16);
*(.rodata)
*(.rodata.str1.4)
*(.eh_frame)
I change this to:
*(.text)
. = ALIGN(16);
*(.eh_frame)
*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
This means the start of rodata will no longer be 16 bytes aligned.
However, the boundary between text and rodata/eh_frame is still aligned to
16 bytes, which is what I think the real purpose of the ALIGN call is.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
The Nand flash was unable to read and write properly
due to Nand Chip Select (nCE) setup was in reverse
order. Also, increase the Nand time out value to 60.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
These were left in accidentally, and are not really useful unless the
code is as broken as it was when it was being developed.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The SerDes initialization should be finished before negating the reset
signal according to the reference manual. This isn't an issue on real
hardware, but we'd better stick to the specifications anyway.
Suggested-by: Liu Dave <DaveLiu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe
slots. Let's support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Update the 86xx reset sequence to try executing a board-specific reset
function. If the board-specific reset is not implemented or does not
succeed, then assert #HRESET_REQ. Using #HRESET_REQ is a more standard
reset procedure than the previous method and allows all board
peripherals to be reset if needed.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Added some info that is printed out when we boot to distiquish if we
built MPC8572DS_config vs MPC8572DS_36BIT_config since they have
different address maps.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The device tree's PHY addresses need to be fixed up if we're using the
SGMII Riser Card.
The 8572, 8536, and 8544 DS boards were modified to call this function.
Code idea taken from Liu Yu <yu.liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In the 36-bit physical config for MPC8572DS when need the start address
of memory and it size to be kept in phys_*_t instead of a ulong since
we support >4G of memory in the config and ulong cant represent that.
Otherwise we end up seeing the memory node in the device tree reporting
back we have memory starting @ 0 and of size 0.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we introduced the 36-bit config of the MPC8572DS board we had the
wrong PCI MEM bus address map. Additionally, the change to the address
map exposes a small issue in our dummy read on the ULI bus. We need
to use the new mapping functions to handle that read properly in the
36-bit config.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Clean up PCI mapping concepts in the 8641 config - rename _BASE
to _BUS, as it's actually a PCI bus address, separate virtual
and physical addresses into _VIRT and _PHYS, and use each
appopriately.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Because the inbound pci windows are mapped generously, set up
the more specific outbound windows first. This way, when we
search the pci regions for something, we will hit on the more
specific region. This can actually be a problem on systems
with large amounts of RAM.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
The PCI_REGION_MEMORY and PCI_REGION_MEM are a bit to similar and
can be confusing when reading the code.
Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY to clarify its used
for system memory mapping purposes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The diufb command usage formatting is non-standard. It was
made standard in preparation for larger command usage updates.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Rather than have the board code initialize SATA automatically during boot,
make the user manually run "sata init". This brings the SATA subsystem in
line with common U-Boot policy.
Rather than having a dedicated weak function "is_sata_supported", people
can override sata_initialize() to do their weird board stuff. Then they
can call the actual __sata_initialize().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The wake up ARP feature need use the memory to process
wake up packet, we enable auto self refresh to support it.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
For light loaded system, we use the 1T timing to gain better
memory performance, but for some heavily loaded system,
you have to add the 2T timing options to board files.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Introduce a new define to seperate out the virtual address that PCI
IO space is at from the physical address. In most situations these are
mapped 1:1. However any code accessing the bus should use VIRT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Introduce a new define to seperate out the virtual address that PCI
memory is at from the physical address. In most situations these are
mapped 1:1. However any code accessing the bus should use VIRT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Use the _MEM_PHYS defines instead of _MEM_BUS for LAW and real address fields
of TLBs. This is what we should have always been using from the start.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Use CONFIG_SYS_PCI*_IO_BUS for the bus relative address instead
of _IO_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_SYS_{PCI,RIO}_MEM_BUS for the bus relative address instead
of _MEM_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Added a CONFIG_SYS_FLASH_BASE_PHYS for use as the physical address and
maintain CONFIG_SYS_FLASH_BASE as the virtual address of the flash.
This allows us to deal with 36-bit phys on these boards in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Added a PIXIS_BASE_PHYS for use as the physical address and maintain
PIXIS_BASE as the virtual address of the PIXIS fpga registers.
This allows us to deal with 36-bit phys on these boards in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
MPC837XEMDS boards can support PCI-E via "PCI-E riser card". The card
provides two PCI-E (x2) ports. Though, only one port can be used in x2
mode. Two ports can function simultaneously in x1 mode.
PCI-E x1/x2 modes can be switched via "pex_x2" environment variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC8315ERDB boards features PCI-E x1 and Mini PCI-E x1 ports. Let's
support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When running in PCI agent mode, the PCI_CLK_OUT signals are not used, so do
not enable them. See the MPC8349EA Reference Manual, Section 4.4.2
"Clocking in PCI Agent Mode".
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- Move the TLB entry of PIXIS_BASE from TLB0 to TLB1[8], because in CAMP mode,
all the TLB0 entries will be invalidated after cpu1 brings up kernel, thus cpu0
can not access PIXIS_BASE anymore (any access will cause DataTLBError exception)
- Set CONFIG_SYS_DDR_TLB_START to 9 for MPC8572DS board.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
The IO port selection for MPC8544DS board:
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2 0x4, 0x5, 0x6, 0x7
PCIE3 0x6, 0x7
This patch changes the PCIE12 and PCIE2 logic more readable.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
PCIE2 and PCIE3 should be decided by corresponing bit in devdisr instead of
PCIE1 bit.
On MPC8572DS board, PCIE refers to PCIE1.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The IO port selection is not correct on MPC8572DS and MPC8544DS board.
This patch fixes this issue.
For MPC8572
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x7, 0xb, 0xc, 0xf
PCIE2 0x3, 0x7
PCIE3 0x7
For MPC8544
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2 0x4, 0x5, 0x6, 0x7
PCIE3 0x6, 0x7
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately. This makes the code easier to read
and understand, and facilitates mapping changes going forward.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits
instead of four.
In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It
should be safe as the fifth bit was defined as reserved and set to 0.
Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Add define used to determine if PCI1 interface is in PCI or PCIX mode.
Convert users of the old PORDEVSR_PCI constant to use MPC85xx_PORDEVSR_PCI1
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
All mpc8548-based boards should implement the suggested workaround
to CPU 2 errata. Without the workaround, its possible for the
8548's core to hang while executing a msync or mbar 0 instruction
and a snoopable transaction from an I/O master tagged to make
quick forward progress is present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
The DDR controller of 8548/8544/8568/8572/8536 processors
have the ECC data init feature, and the new DDR code is
using the feature, and we don't need the way with DMA to
init memory any more.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
address-cells defaults to 2, not 1; so in the unlikely
event that it isn't specified, this patch is required
for correct operation.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Since we've changed the memory map of the board, be nice and
add some checking to try to catch out-of-date .dts files. We do
this by checking the CCSRBAR location in the .dts and comparing
it to the CCSRBAR location in u-boot. If they don't match, a
warning msg is printed. This isn't foolproof, but it's simple and
will catch most of the cases where an out-of-date .dts is present,
including all of the cases where a new u-boot is used with an old
standard MPC8641 .dts file as supplied with Linux.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
This patch creates a memory map with all the devices
in 36-bit physical space, in addition to the 32-bit map.
The CCSR relocation is moved (again, sorry) to
allow for the physical address to be 36 bits - this
requires translation to be enabled. With 36-bit physical
addressing enabled, we are no longer running with VA=PA
translations. This means we have to distinguish between
the two in the config file. The existing region name is
used to indicate the virtual address, and a _PHYS variety
is created to represent the physical address.
Large physical addressing is not enabled by default.
Set CONFIG_PHYS_64BIT in the config file to turn this on.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
The memory map on the 8641hpcn is modified to look more like
the 85xx boards; this is a step towards a more standardized
layout going forward. As part of this change, we now relocate
the flash.
The regions for some of the mappings were far larger than they
needed to be. I have reduced the mappings to match the
actual sizes supported by the hardware.
In addition I have removed the comments at the head
of the BAT blocks in the config file, rather than updating
them. These get horribly out of date, and it's a simple
matter to look at the defines to see what they are set to
since everything is right here in the same file.
Documentation has been changed to reflect the new map, as this
change is user visible, and affects the OS which runs post-uboot.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
There's a lot of setup and foo for the second flash
bank. The problem is, this board doesn't actually have one.
Clean this up. Also, the flash is 8M in size. Get rid
of the confusing aliased overmapping, and just map 8M.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
You can't actually have both, and with some coming changes to
change the memory map for the board and support 36-bit physical,
we need the extra BAT that is being consumed by having both.
I also make non-PCI configs build cleanly, for the sake of sanity.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Fix compilation issue caused by a few mismatches.
Provide proper nand chip select enable/disable in
nand_hwcontrol() rather than in board_nand_init()
just enable once. Remove redundant local nand driver
functions - nand_read_byte(), nand_write_byte() and
nand_dev_ready() to use common nand driver.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Will use mcfmii.c driver in drivers/net rather than
keep creating new mii.c for each future platform.
Remove EB+MCF-EV123, cobra5272, idmr, M5235EVB,
M5271EVB, M5272C3, M5275EVB, M5282EVB, M5329EVB,
M5373EVB, M54451EVB, M54455EVB, M547xEVB, and M548xEVB's
mii.c
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Each different build for M54455EVB and M5235EVB will
create a u-boot.lds linker file. It is redundant to
keep the u-boot.lds
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
This patch defines 1M TLB&LAW size for NAND on MPC8536DS, assigns 0xffa00000
for CONFIG_SYS_NAND_BASE and adds other NAND supports in config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image.
Singed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The DDR1 LAW will precedence the DDR2 LAW, so remove
the second DDR LAW.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
The DDR controller of 86xx processors have the ECC data init
feature, and the new DDR code is using the feature, we don't
need the way with DMA to init memory again.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
This patch defines 1M TLB&LAW size for NAND on MPC8572DS, assigns
0xffa00000 for CONFIG_SYS_NAND_BASE and adds other NAND supports in
config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image, to
make room for the increased code size with NAND enabled.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it
can be shared by both 83xx and 85xx
- Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards
files which use lbus83xx_t.
- Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that
85xx can share them.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Converted MPC8610HCPD, MPC8641HPCN, and SBC8641D to use
fsl_pci_setup_inbound_windows() and ft_fsl_pci_setup().
With these changes the board code is a bit smaller and we get dma-ranges
set in the device tree for these boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Converted ATUM8548, MPC8536DS, MPC8544DS, MPC8548CDS, MPC8568MDS,
MPC8572DS, TQM85xx, and SBC8548 to use fsl_pci_setup_inbound_windows()
and ft_fsl_pci_setup().
With these changes the board code is a bit smaller and we get dma-ranges
set in the device tree for these boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
With this patch u-boot can fixup the dr_mode and phy_type properties
for the Dual-Role USB controller.
While at it, also remove #ifdefs around includes, they are not needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MPC837xE-MDS board's CPLD can auto-detect if the board is on the PIB,
standalone or acting as a PCI agent. User's Guide says:
- When the CPLD recognizes its location on the PIB it automatically
configures RCW to the PCI Host.
- If the CPLD fails to recognize its location then it is automatically
configured as an Agent and the PCI is configured to an external arbiter.
This sounds good. Though in the standalone setup the CPLD sets PCI_HOST
flag (it's ok, we can't act as PCI agents since we receive CLKIN, not
PCICLK), but the CPLD doesn't set the ARBITER_ENABLE flag, and without
any arbiter bad things will happen (here the board hangs during any config
space reads).
In this situation we must disable the PCI. And in case of anybody really
want to use an external arbiter, we provide "pci_external_aribter"
environment variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This involves configuring the SerDes and fixing up the flags and
PHY addresses for the TSECs.
For Linux we also fix up the device tree.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC837xE specs says that SerDes1 has:
— Two lanes running x1 SGMII at 1.25 Gbps;
— Two lanes running x1 SATA at 1.5 or 3.0 Gbps.
And for SerDes2:
— Two lanes running x1 PCI Express at 2.5 Gbps;
— One lane running x2 PCI Express at 2.5 Gbps;
— Two lanes running x1 SATA at 1.5 or 3.0 Gbps.
The spec also explicitly states that PEX options are not valid for
the SD1.
Nevertheless MPC8378 RDB and MDS boards configure the SD1 for PEX,
which is wrong to do.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Currently 64M of LBC SDRAM are mapped at 0xF0000000 which makes
it difficult to use (b/c then the memory is discontinuous and
there is quite big memory hole between the DDR/SDRAM regions).
This patch reworks LBC SDRAM setup so that now we dynamically
place the LBC SDRAM near the DDR (or at 0x0 if there isn't any
DDR memory).
With this patch we're able to:
- Boot without external DDR memory;
- Use most "DDR + SDRAM" setups without need to support for
sparse/discontinuous memory model in the software.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
mpc8536ds.c: In function 'is_sata_supported':
mpc8536ds.c:615: warning: unused variable 'devdisr'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The pixis sgmii command depend on the FPGA support on the board, some 85xx
boards support SGMII riser card but did not support this command, define
CONFIG_PIXIS_SGMII_CMD for those boards which support the sgmii command.
Not like 8544, 8572 has 4 eTsec so that the other two's pixis bits
are not supported by 8544. Therefor, define PIXIS_VSPEED2_MASK and
PIXIS_VCFGEN1_MASK in header file for both boards.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
mpc8572 supports all pcie controllers as end-points with cfg_host_agent=0.
Include host_agent == 0 decode for end-point determination.
This is not needed for the ds reference board since pcie3 will be a host
in order to connect to the uli chip. Include it here as a reference for
other mpc8572 boards.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay based on board ddr frequency and n_ranks.
* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay, 2T based on board ddr frequency and n_ranks.
* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.
* Set memory controller interleaving mode to bank interleaving, and disable
bank(chip select) interleaving mode by default, because the default on-board
DDR DIMMs are 2x512MB single-rank.
* Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Because some dimm parameters like n_ranks needs to be used with the board
frequency to choose the board parameters like clk_adjust etc. in the
board_specific_paramesters table of the board ddr file, we need to pass
the dimm parameters to the board file.
* move ddr dimm parameters header file from /cpu to /include directory.
* add ddr dimm parameters to populate board specific options.
* Fix fsl_ddr_board_options() for all the 8xxx boards which call this function.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Changing the flash from cacheable to cache-inhibited was taking a significant
amount of time due to the fact that we were iterating over the full 256M of
flash. Instead we can just flush the L1 d-cache and invalidate the i-cache.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SGMII and SATA share the serdes on MPC8536 CPU, When SATA disabled and the
driver still try to access the SATA registers, the cpu will hangup.
This patch try to fix this by reading the serdes status before the SATA
initialize.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
When aligning malloc()ed screen_base, invalid offset was added.
This not only caused misaligned result (which did not cause hardware
misbehaviour), but - worse - caused screen_base + smem_len to
be out of malloc()ed space, which in turn caused breakage of
futher malloc()/free() operation.
This patch fixes screen_base alignment.
Also this patch makes memset() that cleans framebuffer to be executed
on first initialization of diu, not only on re-initialization. It looks
correct to clean the framebuffer instead of displaying random garbage;
I believe that was disabled only because that memset caused breakage
of malloc/free described above - which no longer happens with the fix
described above.
Signed-off-by: Nikita V. Youshchenko <yoush@debian.org>
get_cpu_board_revision() returned board revision based on information stored
in global static struct eeprom. It should instead use one from local struct
board_eeprom, to which the data is actually read from EEPROM. The bug led to
system hang after printing L1 cache information on U-Boot startup. The problem
was observed on MPC8555CDS system and possibly affects other Freescale MPC85xx
boards using CFG_I2C_EEPROM_CCID.
The change has been successfully tested on MPC8555CDS system.
Signed-off-by: Rafal Czubak <rcz@semihalf.com>
The spd_dram code shifts the base address, then masks 20 bits, but
forgets to shift the base address back. Fix this by just masking the
base address correctly.
Found this bug while trying to relocate a DDR memory at the base != 0.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The new sys_eeprom.c supports both the old CCID EEPROM format and the new NXID
format, and so it obsoletes board/freescale/common/cds_eeprom.c. Freescale
86xx boards already use sys_eeprom.c, so this patch migrates the remaining
Freescale 85xx boards to use it as well. cds_eeprom.c is deleted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Affected boards:
hidden_dragon
MPC8544DS
MPC8610HPCN
R2DPLUS
TB0229
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544DS and 8572DS platforms support an optional SGMII riser card to
expose ethernet over an SGMII interface. Once the card is in, it is also
necessary to configure the board such that it uses the card, rather than
the on-board ethernet ports. This can either be done by flipping dip switches
on the motherboard, or by modifying registers in the pixis. Either way
requires a reboot.
This adds a command to allow users to choose which ports are routed through
the SGMII card, and which through the onboard ports. It also allows users
to revert to the current switch settings.
This code does not work on the 8572, as the PIXIS is different.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544 DS has an optional SGMII Riser card, which uses different PHY
addresses. Check if we are in SGMII mode, and invoke the SGMII Riser
setup code if so.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544DS and 8572DS systems have an optional SGMII riser card which
exposes new ethernet ports which are connected to the eTSECs via an
SGMII interface. The SGMII PHYs for this board are offset from the standard
PHY addresses, so this code modifies the passed in tsec_info structure to
use the SGMII PHYs on the card, instead.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Add FEC pin set and mii reset in __mii_init(). Change
legacy flash vendor from 2 to AMD LEGACY (0xFFF0),
change cfi_offset to 0, and change CFG_FLASH_CFI to
CONFIG_FLASH_CFI_LEGACY. Correct M54451EVB and
M54455EVB env settings in configuration file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The only board using this driver is the Freescale MPC8610HPCD board.
Removed initialization for the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
PCI I/O space is currently mapped 1:1 at 0xFA000000. Linux requires
PCI I/O space to start at 0 on the PCI bus. This patch maps PCI I/O
space such that 0xFA000000 in the processor's address space maps to 0
on the PCI I/O bus.
Signed-off-by Randy Vinson <rvinson@mvista.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Add the ability for the MPC8349EMDS to run in PCI Agent mode, acting as a
PCI card rather than a host computer.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Change the MPC8349EMDS board to use the generic PCI initialization code
for the mpc83xx cpu.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
There is no point in disabling the icache on 7xx/74xx/86xx parts and not
also flushing the icache. All callers of invalidate_l1_instruction_cache()
call icache_disable() right after. Make it so icache_disable() calls
invalidate_l1_instruction_cache() for us.
Also, dcache_disable() already calls dcache_flush() so there is no point
in the explicit calls of dcache_flush().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Incorrect CFG_HZ value, change 1000000 to 1000.
Rename #waring to #warning. RAMBAR1 uses twice
in start.S, rename the later to FLASHBAR. Insert
nop for DRAM setup. And, env_offset in linker file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Remove non-common flash driver in
board/freescale/m54455evb/flash.c. The non-cfi flash will
use CONFIG_FLASH_CFI_LEGACY to configure the flash
attribute.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset. I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: Scott Wood <scottwood@freescale.com>
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The recent change to move the .bss outside of the image gives older
binutils (ld from eldk4.1/binutils-2.16) some headache:
ppc_85xx-ld: u-boot: Not enough room for program headers (allocated 3, need 4)
ppc_85xx-ld: final link failed: Bad value
We workaround it by being explicit about the program headers and not
assigning the .bss to a program header.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Move to using absolute addressing always. Makes the scripts a bit more
portable and common
* Moved .bss after the end of the image. These allows us to have more
room in the resulting binary image for code and data.
* Removed .text object files that aren't really needed
* Make sure _end is 4-byte aligned as the .bss init code expects this.
(Its possible that the end of .bss isn't 4-byte aligned)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The thinko was quite silly indeed, I messed with !ptr. Normally this
would trigger some fault, but in U-Boot NULL pointer is equal to phys
0, so the code was working still, just didn't actually test mpc8315erdb
environment variable value. Heh.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Freescale ships MPC8315E-RDB boards either with TSEC1 and USB UTMI
support, or without TSEC1 but with USB ULPI PHY support in addition.
With this patch user can specify desired USB PHY.
Also, it seems that we can't distinguish the two boards in software, so
user have to set `mpc8315erdb' environment variable to either 'tsec1'
(TSEC1 enabled) or `ulpi' (board with ULPI PHY, TSEC1 disabled), so that
Linux will not probe for TSEC1.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Update the sys_eeprom.c file to handle both NXID and CCID EEPROM formats. The
NXID format replaces the older CCID format, but it's important to support both
since most boards out there still use the CCID format. This change is in
preparation for using one file to handle both formats. This will also unify
EEPROM support for all Freescale 85xx and 86xx boards.
Also update the 86xx board header files to use the standard CFG_I2C_EEPROM_ADDR
instead of ID_EEPROM_ADDR.
Signed-off-by: Timur Tabi <timur@freescale.com>
The 8544 DS doesn't have any cacheable Local Bus memories set up. By mapping
space for some anyway, we were allowing speculative loads into unmapped space,
which would cause an exception (annoying, even if ultimately harmless).
Removing LBC_CACHE_BASE, and using LBC_NONCACHE_BASE for the LBC LAW solves the
problem.
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch is based on the following patch sent a few minutes ago:
"NAND FSL UPM: driver re-write using the hwcontrol callback"
It is untested, of course. Anton, could you please give it a try.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
With the new LAW interface (set_next_law) we can move to letting the
system allocate which LAWs are used for what purpose. This makes life
a bit easier going forward with the new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
A number of board ports have empty version of board_early_init_f
for no reason since we control its via CONFIG_BOARD_EARLY_INIT_F.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove unused and unconfigured DDR test code from FSL 85xx boards.
Besides, other common code exists.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_OF_LIBFDT instead to support flattened device trees. It is
cleaner, has better functionality, and is better supported.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This was configured to use the deprecated CONFIG_OF_FLAT_TREE, change
to CONFIG_OF_LIBFDT.
WARNING: This conversion is untested because I do not have a board to
test it on.
NOTE: The FDT blob (DTS) must have an /aliases/ethernet0 and (optionally)
/aliases/ethernet1 property for the ethernet to work.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This patch gets rid of the spi_chipsel table and adds a handful of new
functions that makes the SPI layer cleaner and more flexible.
Instead of the spi_chipsel table, each board that wants to use SPI
gets to implement three hooks:
* spi_cs_activate(): Activates the chipselect for a given slave
* spi_cs_deactivate(): Deactivates the chipselect for a given slave
* spi_cs_is_valid(): Determines if the given bus/chipselect
combination can be activated.
Not all drivers may need those extra functions however. If that's the
case, the board code may just leave them out (assuming they know what
the driver needs) or rely on the linker to strip them out (assuming
--gc-sections is being used.)
To set up communication parameters for a given slave, the driver needs
to call spi_setup_slave(). This returns a pointer to an opaque
spi_slave struct which must be passed as a parameter to subsequent SPI
calls. This struct can be freed by calling spi_free_slave(), but most
driver probably don't want to do this.
Before starting one or more SPI transfers, the driver must call
spi_claim_bus() to gain exclusive access to the SPI bus and initialize
the hardware. When all transfers are done, the driver must call
spi_release_bus() to make the bus available to others, and possibly
shut down the SPI controller hardware.
spi_xfer() behaves mostly the same as before, but it now takes a
spi_slave parameter instead of a spi_chipsel function pointer. It also
got a new parameter, flags, which is used to specify chip select
behaviour. This may be extended with other flags in the future.
This patch has been build-tested on all powerpc and arm boards
involved. I have not tested NIOS since I don't have a toolchain for it
installed, so I expect some breakage there even though I've tried
fixing up everything I could find by visual inspection.
I have run-time tested this on AVR32 ATNGW100 using the atmel_spi and
DataFlash drivers posted as a follow-up. I'd like some help testing
other boards that use the existing SPI API.
But most of all, I'd like some comments on the new API. Is this stuff
usable for everyone? If not, why?
Changed in v4:
- Build fixes for various boards, drivers and commands
- Provide common struct spi_slave definition that can be extended by
drivers
- Pass a struct spi_slave * to spi_cs_activate and spi_cs_deactivate
- Make default bus and mode build-time configurable
- Override default SPI bus ID and mode on mx32ads and imx31_litekit.
Changed in v3:
- Add opaque struct spi_slave for controller-specific data associated
with a slave.
- Add spi_claim_bus() and spi_release_bus()
- Add spi_free_slave()
- spi_setup() is now called spi_setup_slave() and returns a
struct spi_slave
- soft_spi now supports four SPI modes (CPOL|CPHA)
- Add bus parameter to spi_setup_slave()
- Convert the new i.MX32 SPI driver
- Convert the new MC13783 RTC driver
Changed in v2:
- Convert the mpc8xxx_spi driver and the mpc8349emds board to the
new API.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Tested-by: Guennadi Liakhovetski <lg@denx.de>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The cross compiler is responsible for providing the correct libraries
and the logic to find the linking libraries.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Currently the serdes will not be initializated due to the
partid's error.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixes eeprom page size so that you can now write more than
64 bytes at a time.
It also makes the board take MAC addresses, if found, from EEPROM.
User should place up to 4 addresses at offset 0x7f00, for
eth{,1,2,3}addr. Any unused addresses should be zero. This group of
four six-byte values should have it's CRC at the end. crc32 and
eeprom commands can be used to accomplish this.
If CRC fails, MAC addresses come from the environment. If CRC
succeeds, the environment is overwritten at startup.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
in the spirit of commit 1ced121600,
85xx's "Update SVR numbers to expand support", simplify SPRIDR processing
and processor ID display. Add REVID_{MAJ,MIN}OR macros to make
REVID dependent code simpler. Also added PARTID_NO_E and IS_E_PROCESSOR
convenience macros.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch is stolen from Anton Vorontsov's patch
for mpc837xerdb boards.
The reference clk and xcorevdd voltage of serdes1/2
is same between mpc837xemds and mpc837xerdb.
8377E: LYNX1- 2 SATA LYNX2- 2 PCIE
8378E: LYNX1- 2 SGMII LYNX2- 2 PCIE
8379E: LYNX1- 2 SATA LYNX2- 2 SATA
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Each file that can be built here now follows some
CONFIG_ option so that they are appropriately built
or not, as needed. And CONFIG_ defines were added
to various board config files to make sure that happens.
The other board/freescale/*/Makefiles no longer need
to reach up and over into ../common to build their
individually needed files any more.
Boards that are CDS specific were renamed with cds_ prefix.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
When we go to 36-bit physical addresses we need to keep the concept of
the physical CCSRBAR address seperate from the virtual one.
For the majority of boards CFG_CCSBAR_PHYS == CFG_CCSRBAR
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linux understands "host" (default), "peripheral" and "otg" (broken).
Though, U-Boot doesn't restrict dr_mode variable to these values (think
of renames in future).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds qe pario pins configuration for AD7843 ADC/Touchscreen
controller and FHCI (QE USB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
On the MPC8377ERDB: 2 SATA and 2 PCI-E.
On the MPC8378ERDB: 2 PCI-E
On the MPC8379ERDB: 4 SATA
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware. Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Back in commit 975a083a5e where
I tried to "8610HPCD: Fix typos in two PCI setup registers", I
botched it due to not realizing that 8610 and 8641 had different
Global Utility Register defintions, one of which was like 85xx,
and the other wasn't. Correct this problem by introducing two
symbols, one for each 86xx SoC, but neither of which is named
anything like 85xx.
My bad. Lovely Wednesday with git bisect. You know.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The two symbols MPC86xx_PORDEVSR_IO_SEL and MPC86xx_PORBMSR_HA
were erroneously present as 85xx names and values, leftover from
the clone wars. Fix this by removing the 85xx cruft from the
86xx codebase.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This is the proper fix for a missing closing brace in the function
ft_cpu_setup() noticed by joe.hamman <at> embeddedspecialties.com.
The ft_cpu_setup() function in mpc8641hpcn.c should have been
removed earlier as it was under the obsolete CONFIG_OF_FLAT_TREE,
but was missed. Only, the sbc8641d was nominally still using it.
It all got ripped out, and the funcality that was in ft_board_setup()
was refactored to remove the CPU portions into the new file
cpu/mpc86xx/fdt.c instead. Make sbc8641d use this now.
Based loosely on an original patch from joe.hamman@embeddedspecialties.com
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Adds the support code in cpu/mpc86xx for the new law setup code
recently created fsl_law.c, and changes the MPC8641HPCN config
to use this code.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Definition update and change from 16bit to 32bit
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>
- Fix EEPROM_data structure definition according to System EEPROM Data Format.
- Read MAC addresses from EEPROM to ethXaddr before saving ethXaddr to
bd->bi_ethaddr.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
This patch implements the fsl_spi driver on the MPC8349EMDS evaluation board.
This board has an ST M25P40 4Mbit EEPROM on its SPI bus
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We should be using the _MEM_PHYS for LAW and TLB setup and not _MEM_BASE.
While _MEM_BASE & _MEM_PHYS are normally the same, _MEM_BASE should only
be used for configuring the PCI ATMU.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
* TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
* load)
Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Before, the order of arguments to the pixis_reset
command needed to be supplied in a hard-coded order.
Generalize the command parsing to allow any order.
Signed-off-by: James Yang <james.yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Convert the board/freescale/common/Makefile to use
CONFIG_* options to select which files to conditionally
compile into the board/freescale/common library rather
than conditionally compiling entire files.
Now handles::
CONFIG_FSL_PIXIS
CONFIG_FSL_DIU_FB
CONFIG_PQ_MDS_PIB
CONFIG_ID_EEPROM is introduced until CFG_ID_EEPROM is gone.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
mpc8360emds.c: In function 'ft_board_setup':
mpc8360emds.c:327: warning: assignment makes pointer from integer without a cast
mpc8360emds.c:329: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast
mpc8360emds.c:334: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast
mpc8360emds.c:341: warning: assignment makes pointer from integer without a cast
mpc8360emds.c:343: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast
mpc8360emds.c:348: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
use tree passed to us in local blob, not global fdt.
Also use fdt_path_offset to convert to relative offset, since absolute
reference is needed to check for rgmii-id mode string value.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]
For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.
The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
connected to SPI.
Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
In order to use GETH1 and GETH2 on the MPC8568E-MDS, we should reset
UCCs.
p.s Similar code exists in the Linux kernel board file (for capability
reasons with older U-Boots), but should be removed some day.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
The old macros made it difficult to know what WIMGE and perm bits
were set for a TLB entry. Actually use the bit masks for these items
since they are only a single bit.
Also moved the macros into mmu.h out of e500.h since they aren't specific
to e500.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Assumes the presence of the aliases node in the DTS to
locate the pci and serial nodes for fixups.
Use consistent fdtaddr and fdtfile in environment variables.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
convert to using simpler mpc85xx style fdt update code; streamline by
eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm
the old school FLAT_TREE code from 83xx (since the sbc8349 was just
converted over to using libfdt).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
mpc8360emds.c: In function ‘ft_board_setup’:
mpc8360emds.c:335: warning: assignment discards qualifiers from pointer target type
mpc8360emds.c:345: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
u-boot itself uses GMII mode on the 8360. Fix up UCC phy-connection-type
properties in the device tree so the PHY gets configured for internal delay on
RX only by the OS, as prescribed by mpc8360 rev. 2.1 pb mds erratum #2.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MPC837xEMDS board support:
* DDR2 400MHz hardcoded and SPD init
* Local bus NOR Flash
* I2C, UART, MII and RTC
* eTSEC RGMII
* PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
Despite user manual, BCSR9.7 is negated (high) on HRST, so
UART2 is disabled. Fix that and configure QE pins properly.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Include config.h earlier in the set of #includes
so as to avoid a incidental and duplicate definition
of CFG_CACHELINE_SIZE.
Signed-off-by: Jon Loeliger
Assumes the presence of the aliases node in the DTS to
locate the ethernet, pci and serial nodes for fixups.
Use consistent fdtaddr and fdtfile in environment variables.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
We already had defines for LAWAR_TRGT_IF_* that we should use
rather than creating new ones. Also, added some missing defines for
PCIE targets.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_*_ADDR as the base of the registers
instead of getting it via &immap.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers
instead of getting it via &immap->im_gur.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the MPC8544DS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update libfdt to commit 8eaf5e358366017aa2e846c5038d1aa19958314e from
the device tree compiler (dtc) project.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These two structures are still needed during the
initialization and setup of the DIU hardware.
So move them to the fsl_diu_fb.h file for now.
Official "blah".
Noticed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Basically, refactor the CFG_PIXIS_VBOOT_MASK values
into the separate board config files.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Add cfb console support to FSL 8610 DIU driver.
Inspect board version from PIXIS to obtain correct pixel format.
Use #define CONFIG_VIDEO in config file to enable fb console.
To switch monitor, set monitor variable to
0 - DVI, 1 - Single link LVDS, 2 - Double link LVDS
followed by "diufb init".
Preserve logo bitmap at the top of the fb console.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
1280x1024 and 1024x768 @ 32 bpp are supported now.
DVI, Single-link LVDS, Double-link LVDS are all supported.
Environmental variable "monitor" is used to specify monitor port.
A new command "diufb" is introduced to reinitialize monitor
and display a BMP file in the memory. So far, 1-bit, 4-bit,
8-bit and 24-bit BMP formats are supported.
diufb init
- initialize the diu driver
Enable the port specified in the environmental variable "monitor"
diufb addr
- display bmp file in memory.
The bmp image should be no bigger than the resolution, 1280x1024
for DVI and double-link LVDS, 1024x768 for single-link LVDS.
Note, this driver allocate memory but doesn't free it after use
It is written on purpose -- to avoid a failure of reallocation
due to memory fragement.
ECC of DDR is disabled for DIU performance. L2 data cache is also disabled.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon loeliger <jdl@freescale.com>
This Freescale logo is a 340 x 128 x 4bpp BMP file
that can be displayed by the DIU Framebuffer driver.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Basically, refactor the CFG_PIXIS_VBOOT_MASK values
into the separate board config files.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The RTC on the M1575 ULI chipset requires a dummy read before
we are able to talk to the RTC. We accomplish this by adding a
second memory region to the PHB the ULI is on and read from it.
The second region is added to maintain compatiabilty with Linux's
view of the PCI memory map.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
if a board/$(VENDOR)/common/Makefile exists, build it.
also add the first such case, board/freescale/common/Makefile, to
handle building board-shared EEPROM, PIXIS, and MDS-PIB code, as
dictated by board configuration.
thusly get rid of alternate build dir errors such as:
FATAL: can't create /work/wd/tmp/u-boot-ppc/board/freescale/mpc8360emds/../common/pq-mds-pib.o: No such file or directory
by putting the common/ mkdir command in its proper place (the common
Makefile). Common bits from existing individual board Makefiles have
been removed.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
add board_add_ram_info, to make memory diagnostic output more
consistent. u-boot banner output now looks like:
DRAM: 256 MB (DDR1, 64-bit, ECC on)
and for boards with SDRAM on the local bus, a line such as this is
added:
SDRAM: 64 MB (local bus)
also replaced some magic numbers with their equivalent define names.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The patch split the PIB init code from pci.c to a single file board/freescale/common/pq-mds-pib.c
And add Qoc3 ATM card support for MPC8360EMDS and MPC832XEMDS board.
Signed-off-by Tony Li <tony.li@freescale.com>
The PCIe bus that the ULI M1575 is connected to has no possible way of
needing more than the fixed amount of IO & Memory space needed by the ULI.
So make it use far less IO & memory space and have it use the shared LAW. This
free's up a LAW for PCIe1 IO space. Also reduce the amount of IO space needed
by each bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It looks like we had a merge issue that duplicated a bit of code
in ft_board_setup. Also, we need to set CONFIG_HAS_ETH0 to get
the MAC address properly set in the device tree on boot for TSEC1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
this adds libfdt support code for the freescale
mpc8313erdb, mpc832xemds, mpc8349emds, mpc8349itx,
and gp boards.
Boards remain compatible with OF_FLAT_TREE.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
PCI1 LAW mapping should use CFG_PCI1_MEM_PHY and not _BASE address.
Enable LBC and ECM errors and clear error registers.
Add tftpflash env var to get uboot from tftp server and flash it.
Add pci/pcie convenience env vars to display register space:
"run pcie3regs" to see all pcie3 ccsr registers
"run pcie3cfg" to see all cfg registers
Whitespace cleanup and MPC8544DS.h
Enable CONFIG_INTERRUPTS.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
MPC8323E based board with 64MB fixed SDRAM, 16MB flash,
five 10/100 ethernet ports connected via an ICPlus IP175C
switch, one PCI slot, and serial. Features not supported
in this patch are SD card interface, 2 USB ports, and the
two phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The OBJTREE != SRCTREE build scenario was broken.
This fixes it.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
There is a Common Flash Interface Driver existed. To use the CFI driver, define CFG_FLASH_CFI in configuration file.
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Add board port under new board/freescale directory
structure and reuse existing PIXIS FPGA support there.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Move the 8641HPCN's PIXIS code to the new directory
board/freescale/common/ as it will be shared by
future boards not in the same processor family.
Write a "pixis_reset" command that utilizes the FPGA
reset sequencer to support alternate soft-reset options
such as using the "alternate" flash bank, enabling
the watch dog, or choosing different CPU frequencies.
Add documentation for the pixis_reset to README.mpc8641hpcn.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
