A system clock of 66MHz was chosen for the pg-wcom-ls102xa.
Compared to the Evalboard, this corresponds to a reduction of 1/3.
The system counter clock should have been reduced accordingly,
but that was not the case, so we had a system time that was
1/3 behind the real time.
This patch corrects the system counter clock to
8.333MHz = 66.667MHz / 8.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to improve power consumption ls102x allows to disable peripherals
that are not in use.
This patch follows SELI8 HW design description and disables peripherals
that are not in use in our designs, the same configuration is applicable
and for EXPU1.
This patch uses available hwconfig option for updating ls102x device
disable configuration.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The default behavior in the latest u-boot revisions is to rotate the
active net device to the next available if the requested link is not
established.
For our ls102x based devices this would mean that if active debug net
device is not available, u-boot will rotate and set the next net device
that is one of the estar adapters.
To return from this situation manual action to set correct ethact
adapter will be needed and this can be annoying when working in
debug mode.
Setting ethrotate=no will disable net adapter rotation and will make sure
that the primary adapter is always used.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In our designs we reserve PRAM area at the end of the RAM, and in order
this area to be visible and taken into account by the u-boot memory mgmt
CONFIG_PRAM has to be defined.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
From production view this is standard test executed during production on
all linux based foxmc cards.
On CENT2 HW defined memory region is zero means that some DDR accesses are
done by memory_post_dataline and memory_post_addrline but pattern tests
are skipped that's why mem_regions is fast there.
On ls102x for the complete DDR region of 1GiB memory_regions_post_test
takes approx. 4min and this is too much for production, so this patch
defines only 1MiB region as compromise.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
is used instead.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Michael Walle <michael@walle.cc> [for kontron-sl28]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards, according to the schematic and per the board I own, use an
M24256-BWDW6TP I2C EEPROM which requires two address bytes.
This fixes the 'mac' command which is used to program, among other
things, the MAC addresses for the ethernet interfaces on the board.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This driver no longer serves a purpose now that we have moved away from
CCF. Drop it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Now that there no separate PLL driver, we can no longer make the PLL
functions static. By moving the PLL driver in with the rest of the clock
code, we can make these functions static again. We still keep the pll
header for unit testing, but it is pretty reduced.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This is effectively a complete rewrite to remove all dependency on CCF.
The code is now smaller, and so is the binary. It also takes up less memory
at runtime (since we don't have to create 40 udevices). In general, I am
much happier with this driver as much of the complexity and late binding
has been removed.
The k210_*_params structs which were previously used to initialize CCF
clocks are now used as the complete configuration. Since we can write our
own division logic, we can now do away with several "half" clocks which
only existed to provide constant factors of two.
The clock IDs have been renumbered to remove unused clocks. This may not be
the last time they are renumbered, since we have diverged with Linux. There
are also still a few clocks left out which may need to be added back in.
In general, I have tried to leave out behavioral changes. However, there is
a small bugfix regarding ACLK. According to the technical reference manual,
its mux comes *after* its divider (which is present only for PLL0). This
would have required yet another intermediate clock to fix with CCF, but
with the new driver it is just 2 lines of code :)
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Since 291da96b8e ("clk: Allow clock defaults to be set during re-reloc
state for SPL only") it has been impossible to set clock defaults before
relocation. This is annoying on boards without SPL, since there is no way
to set clock defaults before U-Boot proper. In particular, the aisram rate
must be changed before relocation on the K210, since U-Boot will hang if we
try and change the rate while we are using aisram.
To get around this, extend the stage parameter to allow force setting
defaults, even if they would be otherwise postponed for later. A device
tree property was decided against because of the concerns in the original
commit thread about the overhead of repeatedly parsing the device tree.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports Falcon boot support for Microchip SAMA5D3 Xplained,
tested on raw MMC, and on raw NAND.
spl_start_uboot() is has the simplest possible implementation.
It doesn't test the environment because enabling environment support
currently causes the SPL to exceed its maximum size (64 KiB).
It doesn't check the serial for incoming characters either because
this functionality currently doesn't seem to work from the SPL
on this board.
Settings for Falcon boot from at FAT partition are also added to
avoid compile failures when CONFIG_SPL_OS_BOOT is enabled, but this
particular case is currently not functional as adding FAT and
partition support cause the SPL to be too big again.
Signed-off-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
Add support command for debugging K3 power domains. This is useful with
the HSM rearch setup, where power domains are directly controlled by SPL
instead of going through the TI SCI layer. The debugging support is only
available in the u-boot codebase though, so the raw register access
power domain layer must be enabled on u-boot side for this to work. By
default, u-boot side uses the TI SCI layer, and R5 SPL only uses the
direct access methods.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Normally, power domains are handled via TI-SCI in K3 SoCs. However,
SPL is not going to have access to sysfw resources, so it must control
them directly. Add driver for supporting this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add driver to support TI K3 generation SoC clocks. This driver registers
the clocks provided via platform data, and adds support for controlling
the clocks via DT handles.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add support for TI K3 SoC PLLs. This clock type supports
enabling/disabling/setting and querying the clock rate for the PLL. The
euclidean library routine is used to calculate divider/multiplier rates
for the PLLs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Current driver only supports registering fixed rate clocks from DT. Add
new API which makes it possible to register fixed rate clocks directly
from e.g. platform specific clock drivers.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
board_fit_image_post_process() passes only start and size of the image,
but type of the image is not passed. So pass fit and node_offset, to
derive information about image to be processed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Copy the best rational approximation calculation routines from Linux.
Typical usecase for these routines is to calculate the M/N divider
values for PLLs to reach a specific clock rate.
This is based on linux kernel commit:
"lib/math/rational.c: fix possible incorrect result from rational
fractions helper"
(sha1: 323dd2c3ed0641f49e89b4e420f9eef5d3d5a881)
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Add default fdtfile environment variable with value
marvell/armada-3720-turris-mox.dtb.
This can be useful for some boot scenarios.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable config options required to add support for USB Mass storage boot,
USB DFU boot, host and device modes in U-Boot.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-11-a-govindraju@ti.com
For USB DFU boot mode there is a limitation on the load address of boot
images that they have to be less than 0x70001000. Therefore, move the
SPL_TEXT_BASE address to 0x70000000.
Currently ATF is being loaded at 0x70000000, if the SPL is being loaded at
0x70000000 then ATF would overwrite SPL image when loaded. Therefore, move
the location of ATF to a latter location in SRAM, past the SPL image. Also
rearrange the EEPROM and BSS data on top of ATF.
Given below is the placement of various data sections in SRAM
┌──────────────────────────────────────┐0x70000000
│ │
│ │
│ │
│ SPL IMAGE (Max size 1.5 MB) │
│ │
│ │
│ │
├──────────────────────────────────────┤0x7017FFFF
│ │
│ SPL STACK │
│ │
├──────────────────────────────────────┤0x70192727
│ GLOBAL DATA(216 B) │
├──────────────────────────────────────┤0x701927FF
│ │
│ INITIAL HEAP (32 KB) │
│ │
├──────────────────────────────────────┤0x7019A7FF
│ │
│ BSS (20 KB) │
├──────────────────────────────────────┤0x7019F7FF
│ EEPROM DATA (2 KB) │
├──────────────────────────────────────┤0x7019FFFF
│ │
│ │
│ ATF (123 KB) │
│ │
│ │
├──────────────────────────────────────┤0x701BEBFB
│ BOOT PARAMETER INDEX TABLE (5124 B)│
├──────────────────────────────────────┤0x701BFFFF
│ │
│SYSFW FIREWALLED DUE TO A BUG (128 KB)│
│ │
├──────────────────────────────────────┤0x701DFFFF
│ │
│ DMSC CODE AREA (128 KB) │
│ │
└──────────────────────────────────────┘0x701FFFFF
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-9-a-govindraju@ti.com
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Supported boot device types in iMX8MN: MMC, DHCP.
Add DISTRO_DEFAULTS config option and include the distro boot command
header file to enable full support of distro boot on i.MX8M Nano EVK (both
DDR and LPDDR derivatives).
Drop previous environment, which was targeting customized boot commands and
boot order.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.
Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.
Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
Uncompressed aarch64 kernel Image are rather large, increase the bootm
size limit to 64 MiB to cater for that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Usb needs IMXRT1050_CLK_USBOH3 clock to be enabled, so let's add it to
clock driver.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Lcd peripheral needs 2 different gates to be enable to work, so let's
introduce the missing one(LCDIF_PIX) and rename the existing one
(LCDIF_APB).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Currently the config options CONFIG_SYS_DFU_DATA_BUF_SIZE and
CONFIG_SYS_DFU_MAX_FILE_SIZE are being set in include/configs/<board>.h
files and also in <board_name>_defconfig files without a Kconfig option. It
is easier for users to set these configs in defconfig files than in config
header files as they are a part of the source code.
Add Kconfig symbols, and update the defconfigs by using tools/moveconfig.py
script.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
TFTP transfer size can be used to re-size the TFTP progress bar on
single line based on the server reported file size. The support for
this has been around from 2019, but it was never converted to proper
Kconfig.
While adding this new Kconfig, enable it by default for OMAP2+ and K3
devices also.
Signed-off-by: Tero Kristo <kristo@kernel.org>
At present if logging not enabled, log_info() becomes a nop. But we want
log output at the 'info' level to be akin to printf(). Update the macro to
pass the output straight to printf() in this case.
This mimics the behaviour for the log_...() macros like log_debug() and
log_info(), so we can drop the special case for these.
Add new tests to cover this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present print_buffer() outputs a hex dump but it is not possible to
place this dump in a string. Refactor it into a top-level function which
does the printing and a utility function that dumps a line into a string.
This makes the code more generally useful.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present print_hex_dump() only supports either 16- or 32-byte lines.
With U-Boot we want to support any line length up to a maximum of 64.
Update the function to support this, with 0 defaulting to 16, as with
print_buffer().
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the comments to the header file so people can find the function info
without digging in the implementation. Fix up the code style and add an
enum for the first arg.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test for this function, to cover the various features. Expand the
expect_str length to take acount of the ~300-bytes lines generated in one
case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This test predates the test framework in U-Boot. It uses #define DEBUG and
assert() to check the result. Update it to use the framework so it can
report failure constitent with other tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
If the console output buffer is exhausted, characters are silently dropped
from the end. Detect this condition and report an error when reading back
the characters.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new function lmb_is_reserved_flags to check if
an address is reserved with a specific flags.
This function can be used to check if an address was
reserved with no-map flags with:
lmb_is_reserved_flags(lmb, addr, LMB_NOMAP);
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add "flags" in lmb_property to save the "no-map" property of
reserved region and a new function lmb_reserve_flags() to check
this flag.
The default allocation use flags = LMB_NONE.
The adjacent reserved memory region are merged only when they have
the same flags value.
This patch is partially based on flags support done in Linux kernel
mm/memblock .c (previously lmb.c); it is why LMB_NOMAP = 0x4, it is
aligned with MEMBLOCK_NOMAP value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make it possible to invoke rescue boot from U-Boot console, without
having to press the factory reset button. This is needed when accessing
the device remotely, for example.
Achieve this by putting rescue command into `bootcmd_rescue` default
environment variable and setting some distroboot environment variables
to their default values when the factory button is pressed.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add dts support for fu740. The HiFive Unmatched support is based on
fu740 cpu and drivers in following patch set.
Signed-off-by: Green Wan <green.wan@sifive.com>
[greentime.hu: set fu740 speed to 1.2GHz]
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
"TCG PC Client Platform Firmware Profile Specification"
requires to measure every attempt to load and execute
a OS Loader(a UEFI application) into PCR[4].
This commit adds the PE/COFF image measurement, extends PCR,
and appends measurement into Event Log.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Replace CONFIG_HASH_CALCULATE by CONFIG_HASH
Fix conversions between pointers and u64.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
MLO has increased to a size greater than the allocated
128 kB in dfu_alt_info_emmc and _mmc.
Therefore, double the allocated size for MLO.raw in
the default environment.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210419065027.5834-1-a-govindraju@ti.com
ut_asserteq_strn is defined twice. Remove one definition.
Fixes: 33d7edfd5f ("test: Add a way to check part of a console line or skip it")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Remove qemu_mips boards because DM migration doesn't make sense.
The board support for qemu_mips is already marked as deprecated
in Qemu in favour of the Malta board. Also qemu_mips support
has been removed from Linux a long time ago.
The official replacement is the Malta board. The same Malta U-Boot
image can be used with Qemu and on physical hardware.
All combinations of Big Endian and Little Endian as well as 32 bit
and 64 bit are supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When building with LTO, the system libc's `errno` variable used in
arch/sandbox/cpu/os.c conflicts with U-Boot's `errno` (defined in
lib/errno.c) with the following error:
.../ld: errno@@GLIBC_PRIVATE: TLS definition in /lib64/libc.so.6
section .tbss mismatches non-TLS reference in
/tmp/u-boot.EQlEXz.ltrans0.ltrans.o
To avoid this conflict use different asm label for this variable when
CONFIG_SANDBOX is enabled.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add macro __efi_runtime_rodata, for const variables with similar purpose
as those using __efi_runtime_data.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Document the macros __efi_runtime and __efi_runtime_data in Sphinx
style.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When linking with LTO, the compiler complains about type mismatch of
variables `__efi_runtime_start`, `__efi_runtime_stop`,
`__efi_runtime_rel_start` and `__efi_runtime_rel_stop`:
include/efi_loader.h:218:21: warning: type of ‘__efi_runtime_start’
does not match original
declaration [-Wlto-type-mismatch]
218 | extern unsigned int __efi_runtime_start, __efi_runtime_stop;
| ^
arch/sandbox/lib/sections.c:7:6: note: ‘__efi_runtime_start’ was
previously declared here
7 | char __efi_runtime_start[0] __attribute__((section(".__efi_run
| ^
Change the type to char[] in include/efi_loader.h.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Increase the BOOTM_LEN to 32M . This would allow a bigger kernel image to be
booted, for example the multi_v7_defconfig.
Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
resetting ...
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We just need to initialize all the clocks pre-reloc. The clock driver
creates a bunch of devices, so we need to increase the pre-reloc malloc
arena.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This simplifies the PLL creation process, since we don't have to pass all
the parameters individually.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This patch changes the functioning of the detection of w1 devices.
The old way was a comparison between detected w1 and the ones described in
the device tree. Now it will just look for the driver matching the family
id of the w1 detected.
The patch is inspired from Maxime Ripard code.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
This patch adds a new "extension" command, which aims at detecting
extension boards connected to the hardware platform, and apply the
Device Tree overlays that describe the hardware present on those
extension boards.
In order to enable this mechanism, board-specific code must implement
the extension_board_scan() function that fills in a linked list of
"struct extension", each describing one extension board. In addition,
the board-specific code must select the SUPPORT_EXTENSION_SCAN Kconfig
boolean.
Based on this:
- "extension scan" makes the generic code call the board-specific
extension_board_scan() function to retrieve the list of detected
extension boards.
- "extension list" allows to list the detected extension boards.
- "extension apply <number>|all" allows to apply the Device Tree
overlay(s) corresponding to one, or all, extension boards
The latter requires two environment variables to exist and set one variable
to run:
- extension_overlay_addr: the RAM address where to load the Device
Tree overlays
- extension_overlay_cmd: the U-Boot command to load one overlay.
Indeed, the location and mechanism to load DT overlays is very setup
specific.
- extension_overlay_name: set by the command: the name of the DT which
will be load during the execution.
When calling the command described in the extension_overlay_cmd
variable, the variable extension_overlay_name will be defined. So a
typical extension_overlay_cmd will look like this:
extension_overlay_cmd=load mmc 0:1 $extension_overlay_addr /boot/$extension_overlay_name
Here is an example on how to use it:
=> run loadfdt
=> fdt addr $fdtaddr
=> setenv extension_overlay_addr 0x1000
=> setenv extension_overlay_cmd 'load mmc 0:1 ${extension_overlay_addr} /boot/${extension_overlay_name}'
=> extension scan
Found 1 extension board(s).
=> extension apply 0
519 bytes read in 3 ms (168.9 KiB/s)
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Move the fdt_valid function to fdt_support.
This changes allow to be able to test the validity of a devicetree in
other c files.
Update code syntax.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Enable CONFIG_DM_ETH in configs/pm9263_defconfig
Drop legacy initialization in board/ronetix/pm9263.c
Remove network related setting from include/configs/pm9263.h
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
With AM64x supporting only K3_NAV_RINGACC_RING_MODE_RING or the exposed
ring mode, all other K3 SoCs have also been moved to this common
baseline. Therefore drop other modes such as
K3_NAV_RINGACC_RING_MODE_MESSAGE (and proxy) to save on SPL footprint.
There is a saving of ~800 bytes with this change for am65x_evm_r5_defconfig.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
AM64 dual mode rings are modeled as pair of Rings objects which has common
configuration and memory buffer, but separate real-time control register
sets for each direction mem2dev (forward) and dev2mem (reverse).
AM64 rings must be requested only using k3_ringacc_request_rings_pair(),
and forward ring must always be initialized/configured. After this any
other Ringacc APIs can be used without any callers changes.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Update struct ti_sci_msg_rm_udmap_tx_ch_cfg_req to latest ABI to support
AM64x BCDMA Block copy channels.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Now that single defconfig can be used for booting AM64 EVM and SK,
default device tree will not work for selecting dtb for kernel.
Update the env to select right dtb based on eeprom.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Current BSS allocation of SPL is as below:
size spl/u-boot-spl
text data bss dec hex filename
144572 5484 1752 151808 25100 spl/u-boot-spl
But 20KB is allocated currently for BSS. Reduce it to 4KB and
save some space for stack.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add pinctrl macros for AM64 SoC. These macro definitions are similar to
that of previous platforms, but adding new definitions to avoid any
naming confusions in the soc dts files.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
By declaring board-specific board_fdt_chosen_bootargs() the kernel
command line arguments can be adjusted before injecting to flat dt
chosen node.
Signed-off-by: Niko Mauno <niko.mauno@vaisala.com>
It can be useful to use the same U-Boot binary for multiple purposes,
say the normal one, one for developers that allow breaking into the
U-Boot shell, and one for use during bootstrapping which runs a
special-purpose bootcmd. Or one can have several board variants that
can share almost all boot logic, but just needs a few tweaks in the
variables used by the boot script.
To that end, allow the control dtb to contain a /config/enviroment
node (or whatever one puts in fdt_env_path variable), whose
property/value pairs are used to update the run-time environment after
it has been loaded from its persistent location.
The indirection via fdt_env_path is for maximum flexibility - for
example, should the user wish (or board logic dictate) that the values
in the DTB should no longer be applied, one simply needs to delete the
fdt_env_path variable; that can even be done automatically by
including a
fdt_env_path = "";
property in the DTB node.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This has the uclass enforce calling detect() before other methods. This
allows drivers to cache information in detect() and perform (cheaper)
retrieval in the other accessors. This also modifies the only instance
where this sequencing was not followed.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Prevent shell access on boot failure by entering an infinite
loop.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Minor cosmetic changes to unify `CONFIG_EXTRA_ENV_SETTINGS'
indentation between Bx50v3 and PPD to make comparison and
review easier and simplify the default boot command.
Signed-off-by: Ian Ray Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
binman FMAP improvements
minor test improvements and fixes
minor dm improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmCKoLERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYCpgf/ROfOg76k18PdWcQTZr10CnU0iqTaOyYx
129hvb4n4bx4Q7Zr/HrWT6y7vvD01NOiNCwSX8qdF7S1bqs2/2AM+Yk/vLimXVOg
UDGXGRABkbHQFVMzBUSmlmQvKoG5G6AhS6/5/F7q4jj+QCVMGarves7G7ImhFOFw
6WKeNGv6FWX4UPSxm0TDJETiIqURNZOsu2vU9DmkR/b1eY13/qf/9J4zzEP1DaJt
7PrKmyblRhPlMsi59EjNyEQOnY/A17en8Ik3Zt336tLPELlczRc4Xp8HslQsy2i3
o457il6x8kl828oVwm3Sx4R/UvM8+qE1jWRcPA7vWrxCy3+AqDcTfQ==
=tiPD
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-29apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm
buildman environment fix
binman FMAP improvements
minor test improvements and fixes
minor dm improvements
Add a reference for the TPM event types and provide missing constants.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add functions to add size of addresses in the device tree using ofnode
references.
If the size is not set, return FDT_SIZE_T_NONE.
Signed-off-by: Chen Guanqiao <chenguanqiao@kuaishou.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In CP115, comphy4 can be configured into SFI port1
(in addition to SFI0). This patch adds the option
described above.
In addition, rename all existing SFI/XFI references:
COMPHY_TYPE_SFI --> COMPHY_TYPE_SFI0
No functional change for exsiting configuration.
Change-Id: If9176222e0080424ba67347fe4d320215b1ba0c0
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Even if comphy types of SATA2/SATA3/SGMII3 and comphy speeds of
1.5G/3G/6.25G were referenced in the driver non configuration (dts)
was using it.
This patch removes unused definitions.
Change-Id: I53ed6f9d3a82b9d18cb4e488bc14d3cf687f9488
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
This patch adds support for running RX training using new command called
"rx_training"
Usage:
rx_training - rx_training <cp id> <comphy id>
RX training allows to improve link quality (for SFI mode)
by running training sequence between us and the link partner,
this allows to reach better link quality then using static configuration.
Change-Id: I818fe67ccaf19a87af50d4c34a9db7d6802049a5
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.
This patch does the following changes:
- PHY_TYPE_XX --> COMPHY_TYPE_XX
- PHY_SPEED_XX --> COMPHY_SPEED_XX
This improves readability, no functional change.
Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
- For some Marvell SoCs, like armada-3700, there are both
USB host and device controller, but on PHY level the
configuration is the same.
- The new type supports both USB device and USB host
- This patch is cherry-picked from u-boot-2015 as-is.
Change-Id: I01262027edd8ec23391cff6fb409b3009aedfbb9
Signed-off-by: jinghua <jinghua@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Add support for regulator-force-boot-off DT property.
This property can be used by the board/device drivers for
turning off regulators on early init stages as pre-requisite
for the other components initialization.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Update R40 .dts{,i} and dt-binding headers to current version from kernel.
Files taken from Linux 5.12-rc1 release
(commit fe07bfda2fb9cdef8a4d4008a409bb02f35f1bd8)
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Enable EFI capsule update features to be enabled by default also with all
dfu valid options for ZynqMP.
This feature was tested on Xilinx ZynqMP zcu104 board with defining
dfu_alt_info="mmc 0:1=boot.bin fat 0 1;u-boot.itb fat 0 1"
and
dfu_alt_info="sf 0:0=boot.bin raw 0 0x50000;u-boot.itb raw 0x80000
0x500000".
There is a need to increase malloc size for getting dfu mmc to work.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
Update R40 .dts{,i} and dt-binding headers to current version from kernel.
Files taken from Linux 5.12-rc1 release
(commit fe07bfda2fb9cdef8a4d4008a409bb02f35f1bd8)
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
-----BEGIN PGP SIGNATURE-----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=JwRN
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2021-04-24' of https://source.denx.de/u-boot/custodians/u-boot-mips
- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
Add support for usb dfu & thor to distro boot on zynq platform.
Add 60s timeout of dfu-utils to start transaction. Remove
DFU_ALT_INFO_RAM as we use bootcmd_usb_dfu instead of dfu_ram.
Remove DFU_ALT_INFO_MMC as part of distro boot cleanup.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change "dfu_usb" to "usb_dfu" for better representation and change
required macros. Add 60s timeout of dfu-utils to start transaction.
Add support for usb thor to distro boot. Remove DFU_ALT_INFO_RAM
as we use bootcmd_usb_dfu instead of dfu_ram.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dfu ram info is wired in connection to Linux kernel and certain setup.
We should change this to be more generic as others command. That's why
using boot via script is the way to go.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In usb boot mode distro boot should select usb device as primary boot
device instead of usb host. So make usb dfu as primary boot device. But do
not list it in boot_targets as fallback option because it is not classic
mode for booting. Using 60s timeout by default should be enough time for
dfu-utils to start transaction. In case none needs this please change
timeout value in the command or disable CONFIG_DFU_TIMEOUT.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add 2 configs CONFIG_LMB_MEMORY_REGIONS and CONFIG_LMB_RESERVED_REGIONS
to change independently the max number of the regions in lmb
library.
When CONFIG_LMB_USE_MAX_REGIONS=y, move the lmb property arrays to
struct lmb and manage the array size with the element 'max' of struct
lmb_region; their are still allocated in stack.
When CONFIG_LMB_USE_MAX_REGIONS=n, keep the current location in
struct lmb_region to allow compiler optimization.
Increase CONFIG_LMB_RESERVED_REGIONS is useful to avoid lmb errors in
bootm when the number of reserved regions (not adjacent) is reached:
+ 1 region for relocated U-Boot
+ 1 region for initrd
+ 1 region for relocated linux device tree
+ reserved memory regions present in Linux device tree.
The current limit of 8 regions is reached with only 5 reserved regions
in DT.
see Linux kernel commit bf23c51f1f49 ("memblock: Move memblock arrays
to static storage in memblock.c and make their size a variable")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As in lmb_region, cnt < max and in the lmb library
use region[i] only with i in 0...cnt, this region array size
can be reduced by 1 element without overflow.
This patch allows to reduce the struct lmb size.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add a max parameter in lmb_region struct to handle test
in lmb_add_region without using the MAX_LMB_REGIONS
define.
This patch allows to modify these size independently for
memory of reserved regions in the next patches.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove the unused field size of struct lmb_region as it is initialized to 0
and never used after in lmb library.
See Linux kernel commit 4734b594c6ca ("memblock: Remove memblock_type.size
and add memblock.memory_size instead")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Adds support for:
* PSCI_FEATURES, which was introduced in PSCI 1.0. This provides API
that allows discovering whether a specific PSCI function is implemented
and its features.
* SYSTEM_RESET2, which was introduced in PSCI 1.1, which extends existing
SYSTEM_RESET. It provides support for vendor-specific resets, providing
reset_type as an additional param.
For additional details visit [1].
Implementations of some functions were borrowed from Linux PSCI driver
code [2].
[1] https://developer.arm.com/documentation/den0022/latest/
[2] drivers/firmware/psci/psci.c
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
So far we were defining a somewhat confusing PHYS_SDRAM_1_SIZE variable,
which originally was only used for setting the memtest boundaries. This
definition in highbank.h has been removed about a year ago (moved to
Kconfig), so we also don't need the hard-coded size definition any longer.
Get rid of the misleading memory size definition, which was actually wrong
anyway (it's 4088 MB for those machines with just 4GB of DRAM).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
All Calxeda machines are actually a poster book example of device tree
usage: the DT is loaded from flash by the management processor into
DRAM, the memory node is populated with the detected DRAM size and this
DT is then handed over to the kernel.
So it's a shame that U-Boot didn't participate in this chain, but
fortunately this is easy to fix:
Define CONFIG_OF_CONTROL and CONFIG_OF_BOARD, and provide a trivial
function to tell U-Boot about the (fixed) location of the DTB in DRAM.
Then enable DM_SERIAL, to let the PL011 driver pick up the UART platform
data from the DT. Also define AHCI, to bring this driver into the driver
model world as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far on Highbank/Midway machines U-Boot only ever uses 512MB of DRAM,
even though the machines have typically 4GB and 8GB, respectively.
That means that so far we didn't need an extra limit for placing the DTB
and initrd, as the 512MB are lower than the kernel's limit ("lowmem",
typically 768MB).
With U-Boot now needing to learn about the actual memory size (to
correctly populate the EFI memory map), it might relocate fdt and initrd
to the end of DRAM, which is out of reach of the kernel.
So add limiting values to the fdt_high and initrd_high environment
variables, to prevent U-Boot from using too high addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_SUPPORT_RAW_INITRD out of the octeontx_common header
and into the defconfig files.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Fixes IDE issues found on the Malta board under Qemu:
1) DMA implied commands were sent to the controller in stead of the PIO
variants. The rest of the code is DMA free and written for PIO operation.
2) direct pointer access was used to read and write the registers instead
of the inb/inw/outb/outw functions/macros. Registers don't have to be
memory mapped and ATA_CURR_BASE() does not have to return an offset from
address zero.
3) Endian isues in ide_ident() and reading/writing data in general. Names
were corrupted and sizes misreported.
Tested malta_defconfig and maltael_defconfig to work again in Qemu.
Signed-off-by: Reinoud Zandijk <reinoud@NetBSD.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This reverts commit 38d6b7ebda.
struct global_data contains a pointer to the bd_info structure. This
pointer was populated spl_set_bd() to a pre-allocated bd_info in the
".data" section. The referenced commit replaced this mechanism to one
that uses malloc(). That new mechanism is only used if SPL_ALLOC_BD=y.
which very few boards do.
The result is that (struct global_data)->bd is NULL in SPL on most
platforms. This breaks falcon mode, since arch_fixup_fdt() tries to
access (struct global_data)->bd and set the "/memory" node in the
devicetree. The result is that the "/memory" node contains garbage
values, causing linux to panic() as it sets up the page table.
Instead of trying to fix the mess, potentially causing other issues,
revert to the code that worked, while this change is reworked.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is a patchset which makes away with the .bind() controller indexing
workaround which was broken since before v2021.04, and then adds PHY
support and MX8M support on top of that. Better add it into the release
early to get as much testing as possible done, because this really does
a lot of changes to the ehci-mx6 driver.
Enable USB host support on MX8MM Verdin.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add ENV_ERASE_PTR macro to handle erase opts and remove the associated
ifdef.
This patch is a extension of previous commit 82b2f41357 ("env_internal.h:
add alternative ENV_SAVE_PTR macro").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
If one of the reads fails when importing redundant environments (a
single read failure), the env_flags wouldn't get initialized in
env_import_redund(). If a user then calls saveenv, the new environment
will have the wrong flags value. So on the next load the new environment
will be ignored.
While debugging this, I also noticed that env/sf.c was not correctly
handling a single read failure, as it would not check the crc before
assigning it to gd->env_addr.
Having a special error path for when there is a single read failure
seems unnecessary and may lead to future bugs. Instead collapse the
'single read failure' error to be the same as a 'single crc failure'.
That way env_check_redund() either passes or fails, and if it passes we
are guaranteed to have checked the CRC.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for devices with R40 dual rank DRAM, and asymmetric
A64 DRAM devices like the Pinephone/3GB.
Also we enable automatic gzipped kernel support, and allow scripted
DT overlay support. The rest of the patches are cleanups, but also
some sunxi-specific preparatory patches for USB3.0 and improved HDMI
support. The bulk of those changes will go through other trees, though.
Build-tested for all 156 sunxi boards, and boot tested on a A64, A20, R40,
H5, H6 and H616 board. USB, SD card, eMMC, HDMI and Ethernet all work
there (where applicable), with the exception of Ethernet on the H5. Since
this is already broken in v2021.04, I will send a separate fix.
The "booti" command to load arm64 Linux kernels supports automatic
decompression of zipped kernel images, but relies on some environment
variables to point to usable buffer RAM.
Add those variables and let them point to some default values, that
should cover most use-cases.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit 69076dff22 ("cmd: pxe: add support for FDT overlays") added
support for loading DT overlay files to PXE boot. However, it needs
additional environment variable which points to memory location which
can be used to temporary store overlay data.
Add it and in the process unify alignment using spaces and fix comment.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However, this call is missing for ls1012a boards. As a result EFI
boot doesn’t work. Fix this issue by removing custom definition of
scan_dev_for_boot and use the default definition instead.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With all preparations in place, switch over to DM_SERIAL.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present we decode simple bus <ranges> using the following assumption:
- parent #address-cells 1
- child #address-cells 1
- child #size-cells 1
However this might not always be the case.
Update to use fdt_addr_t and fdt_size_t in 'struct simple_bus_plat', and
use fdt_read_ranges() to correctly decode it according to the actual
parent and child #address-cells / #size-cells under a Kconfig option
CONFIG_SIMPLE_BUS_CORRECT_RANGE which can be turned on for any board
that needs it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The DSA sandbox driver is used for unit testing the DSA class code.
It implements a simple 2 port switch plus 1 CPU port, and uses a
very simple tag to identify the ports.
The DSA sandbox device is connected via CPU port to a regular Ethernet
sandbox device, called 'dsa-test-eth, managed by the existing eth
sandbox driver. The 'dsa-test-eth' is not intended for testing the
eth class code however, but it is used to emulate traffic through the
'lan0' and 'lan1' front pannel switch ports. To achieve this the dsa
sandbox driver registers a tx handler for the 'dsa-test-eth' device.
The switch ports, labeled as 'lan0' and 'lan1', are also registered
as eth devices by the dsa class code this time. So pinging through
these switch ports is as easy as:
=> setenv ethact lan0
=> ping 1.2.3.5
Unit tests for the dsa class code were also added. The 'dsa_probe'
test exercises most API functions from dsa.h. The 'dsa' unit test
simply exercises ARP/ICMP traffic through the two switch ports,
including tag injection and extraction, with the help of the dsa
sandbox driver.
I took care to minimize the impact on the existing eth unit tests,
though some adjustments needed to be made with the addition of
extra eth interfaces used by the dsa unit tests. The additional eth
interfaces also require MAC addresses, these have been added to the
sandbox default environment.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20210216224804.3355044-5-olteanv@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce a helper API ofnode_phy_is_fixed_link() to detect whether
the ethernet controller connects to a fixed-link pseudo-PHY device.
Note there are two ways to describe a fixed PHY attached to an
Ethernet device:
- the new DT binding, where 'fixed-link' is a sub-node of the
Ethernet device
- the old DT binding, where 'fixed-link' is a property with 5
cells encoding various information about the fixed PHY
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.
It is based on NXP LS1021 SoC and it provides following interfaces:
- IFC interface for NOR, NAND and external FPGA's
- 1 x RGMII ETH for debug purposes
- 2 x SGMII ETH for management communication via back-plane
- 1 x uQE HDLC for management communication via back-plane
- 1 x I2C for peripheral devices
- 1 x SPI for peripheral devices
- 1 x UART for debug logging
It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It's not always desirable to use 'keydir' and some ad-hoc heuristics
to get the filename of the signing key. More often, just passing the
filename is the simpler, easier, and logical thing to do.
Since mkimage doesn't use long options, we're slowly running out of
letters. I've chosen '-G' because it was available.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mkimage supports rsa2048, and rsa4096 signatures. With newer silicon
now supporting hardware-accelerated ECDSA, it makes sense to expand
signing support to elliptic curves.
Implement host-side ECDSA signing and verification with libcrypto.
Device-side implementation of signature verification is beyond the
scope of this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
fdt_add_bignum() is useful for algorithms other than just RSA. To
allow its use for ECDSA, move it to a common file under lib/.
The new file is suffixed with '-libcrypto' because it has a direct
dependency on openssl. This is due to the use of the "BIGNUM *" type.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
rsa-checksum.c sontains the hash_calculate() implementations. Despite
the "rsa-" file prefix, this function is useful for other algorithms.
To prevent confusion, move this file to lib/, and rename it to
hash-checksum.c, to give it a more "generic" feel.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We move qfw into its own uclass and split the PIO functions into a
specific driver for that uclass. The PIO driver is selected in the
qemu-x86 board config (this covers x86 and x86_64).
include/qfw.h is cleaned up and documentation added.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This introduces strlcat, which provides a safer interface than strncat. It
never copies more than its size bytes, including the terminating nul. In
addition, it never reads past dest[size - 1], even if dest is not
nul-terminated.
This also removes the stub for dwc3 now that we have a proper
implementation.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement voltage regulators interfaced by the SCMI voltage domain
protocol. The DT bindings are defined in the Linux kernel since
SCMI voltage domain and regulators patches [1] and [2] integration
in v5.11-rc7.
Link: [1] 0f80fcec08
Link: [2] 2add5cacff
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
It's an old bringup board with out upstream Linux or L4T support
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Similar to support for SHA1 and SHA256, allow the use of hardware hashing
engine by enabling the algorithm and setting CONFIG_SHA_HW_ACCEL /
CONFIG_SHA_PROG_HW_ACCEL.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Checkpatch complains about:
ERROR: "foo * bar" should be "foo *bar"
and
CHECK: Alignment should match open parenthesis
Signed-off-by: Joel Stanley <joel@jms.id.au>
The optee_copy_fdt_nodes is only used to copy op-tee nodes
of U-Boot device tree (from gd->fdt_blob when OF_LIVE is not activated)
to external device tree but it is not compatible with OF_LIVE.
This patch migrates all used function fdt_ functions to read node on
old_blob to ofnode functions, compatible with OF_LIVE and remove this
parameter "old_blob".
The generated "device tree" is checked on stm32mp platform with OF_LIVE
activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add power_max77696_init() function.
Since warp doesn't support DM, the keeping its code in board file is
better than maintainig the file of driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This PWM is used in rk3399-gru-bob and rk3399-gru-kevin to control
the display brightness. We can only change the duty cycle, so on
set_config() we just try to match the duty cycle that dividing duty_ns
by period_ns gives us. To disable, we set the duty cycle to zero while
keeping the old value for when we want to re-enable it.
The cros_ec_set_pwm_duty() function is taken from Depthcharge's
cros_ec_set_bl_pwm_duty() but modified to use the generic pwm type.
The driver itself is very loosely based on rk_pwm.c for the general pwm
driver structure.
The devicetree binding file is from Linux, before it was converted to
YAML at 5df5a577a6b4 ("dt-bindings: pwm: Convert google,cros-ec-pwm.txt
to YAML format") in their repo.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PWM device provided by Chrome OS EC doesn't really support anything
other than setting a relative duty cycle. To support it as a backlight,
this patch makes the PWM period optional in the device tree and pretends
the valid brightness range is its period_ns.
Also adds a sandbox test for a PWM channel that has a fixed period,
checking that the resulting duty_cycle matches on a set_config() even if
the requested period_ns can't be set.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. It is also the only ARCH_T2081 board so remove that support
as well.
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <linuxfae@technexion.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Thomas Weber <weber@corscience.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM by the deadline.
Remove them.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Erik van Luijk <evanluijk@interact.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The mvsata_ide driver was due for DM conversion by v2019.07. As that
has long passed, remove the driver and disable it in the boards which
had enabled it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. In order to
convert to using the DWC SATA driver under DM further migrations are
required.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Signed-off-by: Tom Rini <trini@konsulko.com>
* UEFI spec 2.9 introduced a new memory type EFI_UNACCEPTED_MEMORY_TYPE.
Add it to enum EFI_MEMORY_TYPE.
* Add missing EFI_MEMORY_CPU_CRYPTO constant
* Improve description of EFI_PERSISTENT_MEMORY_TYPE
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Avoid 'make htmldocs' build warnings:
./include/linker_lists.h:224: warning:
Function parameter or member '_type' not described in 'll_entry_ref'
./include/linker_lists.h:224: warning:
Function parameter or member '_name' not described in 'll_entry_ref'
./include/linker_lists.h:224: warning:
Function parameter or member '_list' not described in 'll_entry_ref'
Fixes: 851144350b ("linker_lists: Allow use in data structures")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
* Avoid a warning: "Incorrect use of kernel-doc format".
* Remove duplicate text.
* Clarify usage of EFI_SETTING_VIRTUAL_ADDRESS_MAP.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
-----BEGIN PGP SIGNATURE-----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=4VxR
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210409' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
A now removed comment promises to "limit SYSRAM usage to first 128 KB".
This would imply that only SYSRAM from 0x2ffc0000 - 0x2ffe0000 would be
used. This is not what happens at all.
First, SPL_MAX_SIZE is referenced from SPL_TEXT_BASE, which on all
existing configs is set to 0x2ffc2500, not SYSRAM_BASE (0x2ffc0000).
Some of it is in the first 128 KiB and some of it is in the second
128 KiB chunk of SYSRAM.
Second, SPL_MAX_SIZE, does not restrict the BSS size. While a valiant
attempt is made via SPL_BSS_MAX_SIZE, the value of 0x00100000 is much
larger than SYSRAM, and doesn't account for the non-BSS sections.
Because we're putting the .text and .bss in the same boat, the correct
way to limit them together is via SPL_MAX_FOOTPRINT. With the current
SPL_TEXT_BASE, we couldn't limit even a very basic SPL to the first
128 KiB, and there is no technical reason to do so. Because of this,
simply allow the SPL to use all SYSRAM.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
CONFIG_SPL_BSS_START_ADDR is only used on a few mach- linker scripts.
stm32mp1 uses the generic script under arch/arm/cpu/u-boot-spl.lds,
which does not make use of this definition.
The SPL BSS starts in SRAM, right after .text, .rodata, .data, and
.u_boot_list. A very short version of the STM32MP1 memory map is:
* SYSRAM: 2ffc0000 - 30000000 <- all of SPL is here
* DRAM: c0000000+
0xC0200000 is a DRAM address, and has nothing to do with SPL. It is
just very misleading to have it next to CONFIG_SPL_BSS_MAX_SIZE, or to
have it at all.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for
loading images"), FIT images must be malloc()'d before being loaded.
The old size of 1 MiB is suitable for FIT images with u-boot and an
FDT, but something containing a linux kernel is almost sure to fail.
It's safe to extend malloc all the way to 0xc2000000, but no further.
Linux likes to be loaded at 0xc2000000, so we use that as our cutoff
point. This gives us 29 MiB of malloc() space, which suited for more
complex FIT images including several DTBs, kernel, and OP-TEE images.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
All these files are add for support rt-thread art-pi board
- add board/st/stm32h750-art-pi, defconfig, header support for u-boot
for more information about art-pi, please goto:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patchset has following changes:
- introduce stm32h750.dtsi to support stm32h750 value line
- add pin groups for usart3/uart4/spi1/sdmmc2
- add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
- add stm32h750i-art-pi.dts to support art-pi board
- add stm32h750i-art-pi-u-boot.dtsi to support art-pi board (u-boot)
art-pi board component:
- 8MiB qspi flash
- 16MiB spi flash
- 32MiB sdram
- ap6212 wifi&bt&fm
the detail board information can be found at:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enabled "fsl,legacy-bch-geometry" in U-Boot device tree overlay
to match the legacy BCH geometry layout, which mainline Linux
applies when "fsl,use-minimum-ecc" is not specified in the device
tree.
Reinstated SYS_NAND_ONFI_DETECTION, which when disabled, masked
the mismatch on SOMs with Winbond NAND flash chips.
Signed-off-by: Niel Fourie <lusus@denx.de>
For FSL_USDHC, it do not implement VENDORSPEC_CKEN/PEREN/HCKEN/IPGEN, these
are reserved bits. Instead, use VENDORSPEC_FRC_SDCLK_ON to gate on/off the
card clock output.
After commit b5874b552f ("mmc: fsl_esdhc_imx: add wait_dat0() support"),
we meet SD3.0 card can't work at UHS mode, mmc_switch_voltage() fail because
the second mmc_wait_dat0 return -ETIMEDOUT. According to SD spec, during
voltage switch, need to gate off/on the card clock. If not set the FRC_SDCLK_ON,
after CMD11, hardware will gate off the card clock automatically, so card do
not detect the clock off/on behavior, so will draw the data0 line low until
next command.
Fixes: b5874b552f ("mmc: fsl_esdhc_imx: add wait_dat0() support")
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Convert the UDOO board to use DM_ETH.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block, DM MMC and DM SATA support on iMX6 Udoo
convert board code to match the DM support.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since Toradex provides the full set of overlays for Linux kernel
for display interfaces for both Apalis iMX6Q and Colibri iMX6DL
modules, the video= settings are obsolete. Remove them.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
All the other boards have tdxargs specified for setting manual kernel
command-line arguments. Add them also to NAND-based boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for loading images")'
changed the way buffer allocation worked for SPL to a more flexible
method.
For venice this caused breakage that is resolved by increasing the size
of CONFIG_SYS_SPL_MALLOC_SIZE as the current FIT slighly exceeds 512KiB.
Additionally remove the unnecessary comment on CONFIG_SPL_BSS_MAX_SIZE
and CONFIG_SYS_SPL_MALLOC_SIZE as the size is obvious from the define.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model for MTD and NAND support allowing us to remove
the iomux, init, and most of the static configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable dm support for USB (which also requires dm support for fixed
regulators used for vbus enable) and remove usb iomux which is no
longer needed.
We can remove the handling of otgpwr_en gpio as this is defined in
dt as usbotg vbus-supply but we need to keep the handling of
USB_HUB_RST# for boards that have a USB HUB as that isn't defined in
the dt's currently.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add DEK blob encapsulation support for IMX8M through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application call.
U-boot sends and receives the DEK and the DEK blob binaries through OP-TEE
dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add function to send mailbox command via SMC to get usercode from SDM.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Remove unused SMC function ID 61 and 62.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
In preparation to add SiFive Unmatched board support, let's rename
the existing fu540 board to unleashed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This define was left over from a previous revision, and was never used.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
In i.MX8M platforms the secure memory block has a newer version
than those used in i.MX6/7 platforms, this patch update the driver
to use the correct registers offsets.
Signed-off-by: Aymen Sghaier <aymen.sghaier@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enabling CAAM driver for i.MX8M platforms, a 64 bits architecture,
lead to casting warnings: from/to pointer to/from integer with
different size. This patch fix these warnings
Signed-off-by: Aymen Sghaier <aymen.sghaier@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
U-Boot can instantiate CAAM RNG if needed by crypto operations.
Call sec_init() prior running a blob operation to ensure
RNG is correctly instantiated.
Make sure CAAM clock is enabled and check if a job ring is
available for that operation.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This code was originally developed by Raul Cardenas <raul.casas@nxp.com>
and modified to be applied in U-Boot imx_v2017.03.
More information about the initial submission can be seen
in the link below:
https://lists.denx.de/pipermail/u-boot/2016-February/245273.html
i.MX7D has an a protection feature for Manufacturing process.
This feature uses asymmetric encryption to sign and verify
authenticated software handled between parties. This command
enables the use of such feature.
The private key is unique and generated once per device.
And it is stored in secure memory and only accessible by CAAM.
Therefore, the public key generation and signature functions
are the only functions available for the user.
The manufacturing-protection authentication process can be used to
authenticate the chip to the OEM's server.
Command usage:
Print the public key for the device.
- mfgprot pubk
Generates Signature over given data.
- mfgprot sign <data_address> <data_size>
Signed-off-by: Raul Ulises Cardenas <raul.casas@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This is a straightforward conversion of the old, non-dm driver. It was
done in-place as the deadline for non-dm MMC has passed. Previous
commits ensured that no board depends on the old, non-dm variant. Tested
on a Kirkwood based board with eMMC.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Tested-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Stefan Roese <sr@denx.de>
CC: Gerald Kerma <drEagle@doukki.net>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This will be replaced with the driver model version
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Stefan Roese <sr@denx.de>
CC: Tom Rini <trini@konsulko.com>
Unfortunately this board has no DM support at all. We are also way past
the deadline for driver model support for various devices on this board.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Stefan Roese <sr@denx.de>
These boards use an MMC driver that does not use this definition
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Stefan Roese <sr@denx.de>
CC: Mario Six <mario.six@gdsys.cc>
CC: Dennis Gilmore <dgilmore@redhat.com>
Call 'run update_uboot' to fetch u-boot-spl.kwb via TFTP and write it
into the correct SPI flash location. The latter's size is defined in
DS414's DTB file, so hard-coding it should be acceptable here.
Take care to not append garbage from RAM to the written image and to
stay within assigned flash boundaries even if an oversized image was
fetched.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Move the relevant bits from ds109.{c,h} into common/ and adjust the code
to fit both DS109 and DS414. Moreover:
* Introduce syno_board_id() which translates CONFIG_MACH_TYPE into the
expected board ID tag value.
* Properly initialize isusbhost, mac and mtu fields from env variables.
* Set the right bootargs/bootcmd to correctly boot legacy kernel out of
the (DS414) box. Getting the ramdisk location right is a bit tedious.
Cc: Walter Schweizer <swwa@users.sourceforge.net>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Update hwpartition usage
Check bootbus's arguments
workaround for erratum A-011334 for fsl_esdhc driver
add pulse width detection workaround for fsl_esdhc driver
Use alias num before checking mmc index when creating device
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBr+AgRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebnqQf/dZUk4cpj4q29icFJhAhG3wUkzKdKywWu
wOwHPIaUIetytpjwKTbkv0cUdel5Jhp9mvnJ2O5cRUZlVdgCH+lEQmFiq1O74Jf5
IwYBN74xZuP7+rno3ZxuKhjj2ixbpeg2A5R/o7gaevIgtu4vCK71qrj3y+unjnnt
Rd5BGaVzouMya0lS9cdkrzE1vmuLXs7ZJBvKdppaNda0VScJj+JP3NqooFKRKPU+
OeyblmtfL5lGOXFdY7Wfjg0pzv5L8fJxDaYDxf6iRWWG/X6RO6zV26MWAo28Ga+J
E3fuvl0mBqr1eAg3Cf17j4s9gRZv1tMtS6Mol1scIcBrldalVFA44g==
=x75X
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm
ENOSYS clean-up
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
HS400 mode on the LS1028A SoC isn't reliable. The linux driver has a
workaroung for the pulse width detection. Apply this workaround in
u-boot, too.
This will make HS400 mode work reliably on the LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
We had a problem detecting 8/16bit flash devices connected only via
8bits to the SoC for quite a while. Commit 239cb9d9
[mtd: cfi_flash: Fix CFI flash driver for 8-bit bus support] finally
fixed this 8-bit bus support. But also broke some other boards using
this cfi driver. So this patch had to be reverted.
I spotted a different, simpler approach for this 8-bit bus support
on the barebox mailing list posted by
Oleksij Rempel <bug-track@fisher-privat.net>:
http://www.spinics.net/lists/u-boot-v2/msg14687.html
Here the commit text:
"
Many cfi chips support 16 and 8 bit modes. Most important
difference is use of so called "Q15/A-1" pin. In 16bit mode this
pin is used for data IO. In 8bit mode, it is an address input
which add one more least significant bit (LSB). In this case
we should shift all adresses by one:
For example 0xaa << 1 = 0x154
"
This patch now is a port of this barebox patch to U-Boot.
Along with the change w.r.t from barebox,
Some flash chips can support multiple bus widths, override the
interface width and limit it to the port width.
Tested on 16-bit Spansion flash on sequoia.
Tested 8-bit flashes like 256M29EW, 512M29EW.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Due to a recent change, tests are limited to running on sandbox only.
Correct this so that any architecture can run them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Sean Anderson <seanga2@gmail.com>
Fixes: c79705ea93 ("test: Move dm_test_init() into test-main.c")
Tested-by: Sean Anderson <seanga2@gmail.com>
Avoid 'make htmldocs' build warnings:
./include/os.h:139: warning:
Function parameter or member 'ptr' not described in 'os_realloc'
./include/os.h:139: warning:
Function parameter or member 'length' not described in 'os_realloc'
Fixes: 14e46dfb17 ("sandbox: Add os_realloc()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present debug() statements can cause debuf output to appear when LOG is
enabled but DEBUG is not. This is not intended and it seems that the
condition is wrong.
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently it is not possible to boot Linux from the SD card
by default.
Make the necessary adjustments to allow it.
Reported-by: Peter Bergin <peter@berginkonsult.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrey Zhizhikin <andrey.z@gmail.com> # imx8mn_ddr4_evk
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:
- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Drop a irrelevent comment now the related configs have moved
to the various config files.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is the state as of v5.10 in Linux.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mimicing for example the rk3399, set the SYS_BOOTM_LEN to 64MB so
that regular kernel images can get loaded without problems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SYS_LOAD_ADDR currently is at 0x00280000 which is only 512KB
behind the area where we load u-boot to, which depending on u-boot size
may overlap at some point.
So for safety just pick the same value rk3399 has and set
CONFIG_SYS_LOAD_ADDR to 0x00800800 on rk3368 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When including this file on a board other than sandbox (e.g by enabling
UNIT_TEST and CMD_SETEXPR) an results. Fix it by declaring struct udevice
first.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Some boards may want to show the SKU ID or other information obtained at
runtime. Allow this to come from sysinfo. The board can then provide a
sysinfo driver to provide it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The U_BOOT_CMDREP_COMPLETE() macro produces a build error if CONFIG_CMDLINE
is not enabled. Fix this by updating the macro to provide the 'repeatable'
arugment in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature was dropped from U-Boot some time ago:
f12f96cfaf (sf: Drop spl_flash_get_sw_write_prot")
However, we do need a way to see if a flash device is write-protected,
since if it is, it may not be possible to write to do (i.e. failing to
write is expected).
I am not sure of the correct layer to implement this, so this patch is a
stab at it. If spi-flash makes sense then I will add to the 'sf' also.
Re the points mentioned in the removal commit:
1) This kind of requirement can be achieved using existing
flash operations and flash locking API calls instead of
making a separate flash API.
Which uclass is this?
2) Technically there is no real hardware user for this API to
use in the source tree.
I do want coral (at least) to support this.
3) Having a flash operations API for simple register read bits
also make difficult to extend the flash operations.
This new patch only mentions write-protect being on or off, rather than
the actual mechanism.
4) Instead of touching generic code, it is possible to have
this functionality inside spinor operations in the form of
flash hooks or fixups for associated flash chips.
That sounds to me like what drivers are for. But we still need some sort
of API for it to be accessible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox is special in that it is used for testing and it does not match
any particular target architecture. Allow it to load an image from any
architecture, so that 'bootm' can be used as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when a file is bound to a host device it is always marked as
removeable. Arguably the device is removeable, since it can be unbound at
will. However while it is bound, it is not considered removable by the
user. Also it is useful to be able to model both fixed and removeable
devices for code that distinguishes them.
Add a -r flag to the 'host bind' command and plumb it through to provide
this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow referencing a CBFS file in the flashmap, so that it is possible to
boot from coreboot, where files are not available from binman.
Signed-off-by: Simon Glass <sjg@chromium.org>
CBFS now supports compressed filed. Add support for reading this
information so that the correct decompression can be applied. The
decompression itself is not implemented in CBFS.
Signed-off-by: Simon Glass <sjg@chromium.org>
The file traversal functions currently use a single global CBFS. In some
cases we need to access multiple CBFSs to obtain different files. Add new
functions to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases CBFS does not start with a header but is just a collection
of files. It is possible to support this so long as the size of the CBFS
is provided.
Update the cbfs_init_mem() function to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When U-Boot is booted from coreboot the SMBIOS tables are written by
coreboot, not U-Boot. The existing method of updating the BIOS version
string does not work in that case, since gd->smbios_version is only set
when U-Boot writes the tables.
Add a new function which allows the version to be updated by parsing the
tables and writing the string in the correct place. Since coreboot
provides a pointer to the SMBIOS tables in its sysinfo structure, this
makes it easy to do the update.
Signed-off-by: Simon Glass <sjg@chromium.org>
CBFS now supports attributes for things that cannot fit in the header as
originally conceived. Add the structures for these.
Also rename attributes_offset to something shorter, to ease code
readability.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the eMMC device does not have an alias so it appears after
the SD card which is device 1. There is no device 0 which is odd.
Make the eMMC device be the first one. Update the boot script to use the
new device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
dfu_free_entities() invoking dfu_free_entity_sf() has let to segementation
faults due to double freeing the same device.
spi_flash_free() is not relevant for the driver model but exists only for
compatibility with old drivers.
We must not remove any device here:
* The device may still be referenced.
* We don't want to have to probe again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
driver model support for of-platdata-inst
support of-platdata-inst on x86 / coral
binman support for exapanded entries
binman convert docs to reST
ti-sysc fix for duplicate uclass driver
patman minor improvements
pylibfdt build only if needed
correct obscure CI error with OF_PLATDATA_INST
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBdZYURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreb2rQgAyr1rufrt1UGjZlVjk0HtqX0sdmcOoE4e
6NIuatWXPcP2QR93O9zeGgf/yqNIf3lVIa6Cy3baJBfP6fceZ8B24/xgKKEauPFf
g99sec+q7LPL/oigajXIaWorFXK/NDRtQcSIQFu/EmvCmi0m8Iu0HKFa7YBqa7dc
YdhGnJZZOdYuQmlKewq9q4cIr6qNtTZczsozt4PNZVgB2lKusBNyKRPZErNEFiN6
7A56bb8tcfWgGXenKVTUUcyjWRXM2tt4QtrPFedZsF6cLa8D5v4MfWMs0QBRFl/u
fMzxyeb46x0wsYBNqIBOC7DQWaU/ZeFlr5mQObIH0ypdcsUnEX98sw==
=Ld3P
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26mar21-take2' of git://git.denx.de/u-boot-dm into next
dtoc support for of-platdata-inst
driver model support for of-platdata-inst
support of-platdata-inst on x86 / coral
binman support for exapanded entries
binman convert docs to reST
ti-sysc fix for duplicate uclass driver
patman minor improvements
pylibfdt build only if needed
correct obscure CI error with OF_PLATDATA_INST
Add a warning to each of these functions so that people do not attempt to
use them outside driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Make use of the new priv/plat data region if enabled. This is implemented
as a simple offset from the position set up by dtoc to the new position.
So long as all access goes through dm_priv_to_rw() this is safe.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the device priv/data data allocated by dtoc is stored in the
data section along with other variables. On some platforms it is better
to allocate space for it separately, e.g. if SPL is running from read-only
memory.
Create a new space with the same size as that allocated by dtoc, ready for
use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
When of-platdata-inst is active, use the flags in the new udevice_rt
table, dropping them from the main struct udevice. This ensures that the
latter is not updated at runtime.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when driver model needs to change a device it simply updates
the struct udevice structure. But with of-platdata-inst most of the fields
are not modified at runtime. In fact, typically only the flags need to
change.
For systems running SPL from read-only memory it is convenient to separate
out the runtime information, so that the devices don't need to be copied
before being used.
Create a new udevice_rt table, similar to the existing driver_rt. For now
it just holds the flags, although they are not used in this patch.
Add a new Kconfig for the driver_rt data, since this is not needed when
of-platdata-inst is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the i2c emulators require access to the devicetree, which is
not possible (by design) with of-platdata.
Add a way for drivers to record the of-platdata index of their emulator,
so that we can still find the emulator.
This allows i2c emulation to work with of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function finds a device by its driver_info index. With
of-platdata-inst we do not use driver_info, but instead instantiate
udevice records at build-time.
However the semantics of using the function are the same in each case:
the caller provides an index and gets back a device.
So rename the function to device_get_by_ofplat_idx(), so that it can be
used for both situations. The caller does not really need to worry about
the details.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is now only used in a test. Drop it. Also drop
DM_DRVINFO_GET() which was the only purpose for having the function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to allow SoCs to create their own drivers for this so that they
can use their own of-platdata structs. To minimise code duplication,
export the driver operations and the ofdata_to_plat() setup function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
When dt-structs.h is used, include the dt-decl.h header as well, so that
these declarations are available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Setup will always occur before ExitBootServices(). So eliminate
EFI_SETUP_AFTER_BOOTTIME_EXIT. Put the SetVirtualAddressMap() test into a
separate class so that we can execute it last.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The ESRT is initialised during efi_init_objlist after
efi_initialize_system_table().
The ESRT is recreated from scratch at the following events:
- successful UpdateCapsule;
- FMP instance install.
The code ensures that every ESRT entry has a unique fw_class value.
Limitations:
- The ESRT is not updated if an FMP instance is uninstalled;
- the fields image_type and flags are in the current implementation left
undefined. Setting these values will require a per-platform function
that returns the image_type/flags as a function of the image fw_class.
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: AKASHI Takahiro <takahiro.akashi@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Andre Przywara <andre.przywara@arm.com>
CC: Alexander Graf <agraf@csgraf.de>
CC: nd@arm.com
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Remove two EFI_CALL() indirections.
Move ESRT GUID in efidebug's list of GUIDs.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now we install EFI_LOAD_FILE2_PROTOCOL to load an initrd
unconditionally. Although we correctly return various EFI exit codes
depending on the file status (i.e EFI_NO_MEDIA, EFI_NOT_FOUND etc), the
kernel loader, only falls back to the cmdline interpreted initrd if the
protocol is not installed.
This creates a problem for EFI installers, since they won't be able to
load their own initrd and continue the installation. It also makes the
feature hard to use, since we can either have a single initrd or we have
to recompile u-boot if the filename changes.
So let's introduce a different logic that will decouple the initrd
path from the config option we currently have.
When defining a UEFI BootXXXX we can use the filepathlist and store
a file path pointing to our initrd. Specifically the EFI spec describes:
"The first element of the array is a device path that describes the device
and location of the Image for this load option. Other device paths may
optionally exist in the FilePathList, but their usage is OSV specific"
When the EFI application is launched through the bootmgr, we'll try to
interpret the extra device path. If that points to a file that exists on
our disk, we'll now install the load_file2 and the efi-stub will be able
to use it.
This opens up another path using U-Boot and defines a new boot flow.
A user will be able to control the kernel/initrd pairs without explicit
cmdline args or GRUB.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
A following patch introduces a different logic for loading initrd's
based on the EFI_LOAD_FILE2_PROTOCOL.
Since similar logic can be applied in the future for other system files
(i.e DTBs), let's add some helper functions which will retrieve and
parse file paths stored in EFI variables.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
On the following patches we allow for an initrd path to be stored in
Boot#### variables. Specifically we encode in the FIlePathList[] of
the EFI_LOAD_OPTIONS for each Boot#### variable.
The FilePathList[] array looks like this:
kernel - 0xff - VenMedia(initrd GUID) - initrd1 - 0x01 initrd2 - 0xff
So let's add the relevant functions to concatenate and retrieve a device
path based on a Vendor GUID.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reformat function descriptions.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When uploading an EFI binary via the UART we need to assign a device path.
* Provide devicepath node to text conversion for Uart() node.
* Provide function to create Uart() device path.
* Add UART support to efi_dp_from_name().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
LS1028A-QDS has CONFIG_SPI_FLASH_SST and CONFIG_SPI_FLASH_EON defines
present in header. Move these entries from header to defconfigs.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is now safe to remove Flexspi configs NXP_FSPI_FLASH_SIZE and
NXP_FSPI_FLASH_NUM options from headers as they are no longer used by
driver anymore.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The name of the define must indicate 'Asynchronous', so 'ASYNC' is more
appropriate. AYSNC is probably a typo, and checkpatch script is throwing
a warning if this is set in the board include files.
It is save to change this now as none of the existing designs is using it
so far, but we will use it in our design it help to make IFC settings
more transparent.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When OF_PLATDATA_INST is enabled we don't need to create the uclass list.
Instead we just need to point to the existing list. Update the code
accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add macros which work with instantiated devices and uclasses, as created
at build time by dtoc. Include variants that can be used in data
structures.
These are mostly used by dtoc but it is worth documenting them fully for
the occasional case where they might come up in user code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present linker lists are designed for use in code. They make use of
statements within expressions ({...}), for example.
It is possible to generate a reference to a linker_list entry that can
be used in data structures, where such features are not permitted. It
requires that the reference first be declared as extern. In other
words the existing macro needs to be split into two parts.
Add new macros to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for generating a file containing uclass instances. This avoids
the need to create these at run time.
Update a test uclass to include a 'priv_auto' member, to increase test
coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Typically dtoc can detect the header file needed for a driver by looking
for the structs that it uses. For example, if a driver as a .priv_auto
that uses 'struct serial_priv', then dtoc can search header files for the
definition of that struct and use the file.
In some cases, enums are used in drivers, typically with the .data field
of struct udevice_id. Since dtoc does not support searching for these,
add a way to tell dtoc which header to use. This works as a macro included
in the driver definition.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot operates in several phases, typically TPL, SPL and U-Boot proper.
The latter does not use dtoc.
In some rare cases different drivers are used for two phases. For example,
in TPL it may not be necessary to use the full PCI subsystem, so a simple
driver can be used instead.
This works in the build system simply by compiling in one driver or the
other (e.g. PCI driver + uclass for SPL; simple_bus for TPL). But dtoc has
no way of knowing which code is compiled in for which phase, since it does
not inspect Makefiles or dependency graphs.
So to make this work for dtoc, we need to be able to explicitly mark
drivers with their phase. This is done by adding an empty macro to the
driver. Add support for this in dtoc.
Signed-off-by: Simon Glass <sjg@chromium.org>
More than one pumpkin board has been made with different MediaTek SoCs.
Rename the pumpkin board to follow the naming convention of all
other MediaTek boards and also to not be confusing when other pumpkin
boards will be added in follow-up commits.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
When uploading an EFI binary via the UART we need to assign a device path.
* Provide devicepath node to text conversion for Uart() node.
* Provide function to create Uart() device path.
* Add UART support to efi_dp_from_name().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The api_public.h header file undefined macro CONFIG_SYS_64BIT_LBA.
But api/api_storage.c includes this header before including part.h,
causing the type of lbaint_t and subsequently the type signature of
blk_dread() and blk_dwrite() functions to change from the rest of U-Boot
(if CONFIG_SYS_64BIT_LBA is defined for the board).
This is of course wrong, because the call to blk_dread() / blk_dwrite()
will receive mangled arguments.
Fix this by removing the undef of macro CONFIG_SYS_64BIT_LBA and instead
make the immediate code do what it would do as if the macro was not
defined.
Add a FIXME to whoever is maintaining this code.
CI managed to trigger this bug when compiling for lsxhl_defconfig, which
has CONFIG_API selected. The compiler complained about blk_dwrite() and
blk_dread() not matching original declarations:
include/blk.h:280:15: warning: type of ‘blk_dwrite’ does not match
original declaration
[-Wlto-type-mismatch]
280 | unsigned long blk_dwrite(struct blk_desc *block_dev, lbaint_t st
| ^
drivers/block/blk-uclass.c:456:15: note: type mismatch in parameter 2
456 | unsigned long blk_dwrite(struct blk_desc *block_dev, lbaint_t st
| ^
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYFRW+Q4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXHc0AJ9fMaRhTXa1AmnUgO87HFgHH1ZcRwCfYO7EHZTi
0bZtL6HrniwUmXyb2U4=
=J6PL
-----END PGP SIGNATURE-----
Merge tag 'video-for-v2021.04' of https://source.denx.de/u-boot/custodians/u-boot-video
- drop unprintable characters from video font header
Unfortunately -ENODATA is not available in OpenBSD. Use -EBADMSG
instead, to indicate a missing timestamp.
Fixes: c5819701a3 image: Adjust the workings of fit_check_format()
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).
This patch adds the required board support to boot Si-Linux EK874 board
based on R8A774C0 SoC.
DTS files apart from r8a774c0-ek874-u-boot.dts and r8a774c0-u-boot.dtsi
have been imported from Linux kernel 5.11 commit f40ddce88593
("Linux 5.11").
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
The HiHope RZ/G2M board from HopeRun consists of main board
(HopeRun HiHope RZ/G2M main board) and sub board(HopeRun
HiHope RZ/G2M sub board). The HiHope RZ/G2M sub board sits
below the HiHope RZ/G2M main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2M board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
-----BEGIN PGP SIGNATURE-----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=nIJc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210312' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Add WATCHDOG_RESET() in MTD framework and STM32 QSPI driver
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
Current BSS allocation of SPL is as below:
$ size spl/u-boot-spl
text data bss dec hex filename
132369 7852 1496 141717 22995 spl/u-boot-spl
But 20KB is allocated currently for BSS. Reduce it to 3KB and save some
space for stack.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In a previous attempt to unify config options and remove items
from the whitelist file, SPL items were moved into a section
enabled with CONFIG_SPL_BUILD. Unfortunately, SPL_PAD_TO
is referenced at the head Makefile and uses this define
to create padding of the output file. When it was moved
to CONFIG_SPL_BUILD, it caused boot errors with devices
that are not booting from NOR. Fix the boot issues by moving
SPL_PAD_TO out so it's always.
Fixes: 7bb33e4684 ("ARM: da850-evm: Unify config options with Kconfig")
Signed-off-by: Adam Ford <aford173@gmail.com>
This Trusted Application allows enabling SCP03 as well as provisioning
the keys on TEE controlled secure element (ie, NXP SE050).
All the information flowing on buses (ie I2C) between the processor
and the secure element must be encrypted. Secure elements are
pre-provisioned with a set of keys known to the user so that the
secure channel protocol (encryption) can be enforced on the first
boot. This situation is however unsafe since the keys are publically
available.
For example, in the case of the NXP SE050, these keys would be
available in the OP-TEE source tree [2] and of course in the
documentation corresponding to the part.
To address that, users are required to rotate/provision those keys
(ie, generate new keys and write them in the secure element's
persistent memory).
For information on SCP03, check the Global Platform HomePage and
google for that term [1]
[1] globalplatform.org
[2] https://github.com/OP-TEE/optee_os/
check:
core/drivers/crypto/se050/adaptors/utils/scp_config.c
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
The existing log_ret() and log_msg_ret() macros consider an error to be
less than zero. But some function may return a positive number to indicate
a different kind of failure. Add macros to check for that also.
Signed-off-by: Simon Glass <sjg@chromium.org>
When multiple log() calls are used which don't end in newline, the
log prefix is prepended multiple times in the same line. This makes the
output look strange.
Fix this by detecting when the previous log record did not end in newline.
In that case, setting a flag.
Drop the unused BUFFSIZE in the test while we are here.
As an example implementation, update log_console to check the flag and
produce the expected output.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only a single flag (force_debug) is used in log records. Before
adding more, convert this into a bitfield, so more can be added without
using more space.
To avoid expanding the log_record struct itself (which some drivers may
wish to store in memory) reduce the line-number field to 16 bits. This
provides for up to 64K lines which should be enough for anyone.
Signed-off-by: Simon Glass <sjg@chromium.org>
As an example of an SPL test, add a new test for loading a FIT within
SPL. This runs on sandbox_spl. For this to work, the text base is adjusted
so that there is plenty of space available.
While we are here, document struct spl_load_info properly, since this is
currently ambiguous.
This test only verifies the logic path. It does not actually check that
the image is loaded correctly. It is not possible for sandbox's SPL to
actually run u-boot.img since it currently includes u-boot.bin rather than
u-boot. Further work could expand the test in that direction.
The need for this was noted at:
http://patchwork.ozlabs.org/project/uboot/patch/20201216000944.2832585-3-mr.nuke.me@gmail.com/
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function can only locate the u-boot ELF file. For SPL it
is handy to be able to locate u-boot.img since this is what would normally
be loaded by SPL.
Add another argument to allow this to be selected.
While we are here, update the function to load SPL when running in TPL,
since that is the next stage.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present SPL only runs driver model tests. Update it to run all
available tests, i.e. in any test suite.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present each test suite has its own portion of the linker_list section
of the image, but other lists are interspersed. This makes it hard to
enumerate all the available tests without knowing the suites that each one
is in.
Place all tests together in a single contiguous list by giving them
common prefix not used elsewhere in U-Boot. This makes it possible to find
the start and end of all tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use the linker list directly. This is not very friendly, so
add a helpful macro instead. This will also allow us to change the naming
later without updating this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use this function instead of implementing it separately for driver model.
Make ut_run_tests() private since it is only used in test-main.c
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use a global test state for all driver-model tests. Make use
of a local struct like we do with the other tests.
To make this work, add functions to get and set this state. When a test
starts, the state is set (so it can be used in the test). When a test
finishes, the state is unset, so it cannot be used by mistake.
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver model tests are generally run twice, once with livetree enable and
again with it disabled. Add a function to handle this and call it from the
driver model test runner.
Make ut_run_test() private since it is not used outside test-main.c now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of having a separate function for running driver model tests, use
the common one. Make the pre/post-run functions private since we don't
need these outside of test-main.c
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this function into test-main so that all the init is in one place.
Rename it so that its purpose is clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver model is a core part of U-Boot. We don't really need to have a
separate test structure for the driver model tests and it makes it harder
to write a test if you have to think about which type of test it is.
Subsume the fields from struct dm_test_state into struct unit_test_state
and delete the former.
Signed-off-by: Simon Glass <sjg@chromium.org>
For driver model tests we want to reinit the data structures so that
everything is in a known state before the test runs. This avoids one test
changing something that breaks a subsequent tests.
Move the call for this into test_pre_run().
Signed-off-by: Simon Glass <sjg@chromium.org>
Ultimately we want to get rid of the special driver model test init and
use test_pre_run() and test_post_run() for all tests. As a first step,
use those function to handle console recording.
For now we need a special case for setting uts->start, but that wil go
away once all init is in one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Split out the test preparation into a separation function before
expanding it. Add a post-run function as well, currently empty.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new test runner that will eventually be able to run any test. For
now, have it run the 'command' unit tests, so that the functionality in
cmd_ut_category() moves into it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is the main test function for driver model but not for other tests.
Rename the file and the function so this is clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
The STM32MP15 boards have no reason to configure bootdelay in stm32mp1.h
as it is already done with CONFIG_BOOTDELAY (default = 2) and in
include/env_default.h.
This patch allows configuration for customers which reuse stm32mp1.h
and reduce the size of the default environment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add target to Makefile to generate "u-boot-spl-dtb.hex" for Intel
SOCFPGA SOC64 devices (Stratix 10 and Agilex). "u-boot-spl-dtb.hex"
is hex formatted spl with and offset of CONFIG_SPL_TEXT_BASE. It
combines the spl image and dtb. "u-boot-spl-dtb.hex" is needed to
generate the final configuration bitstream for Intel SOCFPGA SOC64
devices.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
CONFIG_BOOTCOMMAND have been moved to Kconfig.boot. This patch
move the CONFIG_BOOTCOMMAND macro from socfpga_soc64_common.h to
*_defconfig file for both Stratix 10 and Agilex.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Carve out a function to translate a Unicode code point to an 8bit codepage.
Provide a unit test for the new function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Now that we have switched to CONFIG_OF_CONTROL, and we can use the
env variable 'fdtcontroladdr' directly instead of creating one that
is duplicated.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The QEMU ppce500 target integrates a Freescale I2C controller and
has a Pericom pt7c4338 RTC connected to it. Enable corresponding
DM drivers so that 'date' command is actually useful.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present the board supports non-DM version PCI and E1000 drivers.
Switch over to use DM ETH and PCI by:
- Rewrite the PCI address map functions using DM APIs
- Enable CONFIG_MISC_INIT_R to do the PCI initialization and
address map
- Drop unnecessary ad-hoc config macros
- Remove board_eth_init() in the board codes
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The QEMU ppce500 target integrates 2 NS16550 serial ports. Switch
over to use the DM version of the driver by:
- drop unnecessary ad-hoc config macros
- add get_serial_clock() in the board codes
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds a basic test for the newly introduced 'addrmap' command.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[Rebase]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
At present address_map[] is static and its type is unknown to external
modules. In preparation to create a command to list its contents, this
patch moves its type definition and declaration to the header file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Remove the extern of the header because they are useless.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_SYS_PCI_MAP_END currently points to 0xe8000000, which means
the upper end of the virtual address mapped to PCI bus address ends
at 0xe8000000. But this is wrong as the CCSBAR was already mapped
at 0xe0000000 with a 1 MiB size.
Fixes: fa08d39517 ("PPC 85xx: Add qemu-ppce500 machine")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds support for more PMBus compatible devices to the NXP
drivers for its QorIQ family devices. At runtime, the voltage regulator is
queried over I2C, and the required voltage multiplier determined. This
change supports the DIRECT and LINEAR PMBus voltage reporting modes.
Previously, the driver only supported a few specific devices such as the
IR36021 and LTC3882, so this change allows the QorIQ series to be used
with a much larger variety of core voltage regulator devices.
checkpatch warning "Use if (IS_DEFINED (...))" was ignored to maintain
consistency with the existing code.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYEE0zg4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXMQWAJ4pwG2oykEwa+BEC5JUrJ9B/QWa+wCeP1HwJS5N
siPaX+vgDLOqTg1Y/T4=
=0Dow
-----END PGP SIGNATURE-----
Merge tag 'next-2021-03-04' of https://gitlab.denx.de/u-boot/custodians/u-boot-video into next
- convert sunxi_display to DM_VIDEO
Using the internal vs. external pull resistors it is possible to get
27 different combinations from 3 strapping pins. Add an implementation
of this.
This involves updating the sandbox GPIO driver to model external and
(weaker) internal pull resistors. The get_value() method now takes account
of what is driving a pin:
sandbox: GPIOD_EXT_DRIVEN - in which case GPIO_EXT_HIGH provides the
value
outside source - in which case GPIO_EXT_PULL_UP/DOWN indicates the
external state and we work the final state using those flags and
the internal GPIOD_PULL_UP/DOWN flags
Of course the outside source does not really exist in sandbox. We are just
modelling it for test purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
The new update_flags() method is more flexible since it allows the
driver to see the full flags all at once. Use that in preference to these
two functions. Add comments to that effect.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
It is convenient to be able to adjust some of the flags for a GPIO while
leaving others alone. Add a function for this.
Update dm_gpio_set_dir_flags() to make use of this.
Also update dm_gpio_set_value() to use this also, since this allows the
open-drain / open-source features to be implemented directly in the
driver, rather than using the uclass workaround.
Update the sandbox tests accordingly. This involves a lot of changes to
dm_test_gpio_opendrain_opensource() since we no-longer have the direciion
being reported differently depending on the open drain/open source flags.
Also update the STM32 drivers to let the uclass handle the active low/high
logic.
Drop the GPIOD_FLAGS_OUTPUT() macro which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This function can be used to get any flags, not just direction flags.
Rename it to avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
It is more useful to be able to read all the flags, not just the direction
ones. In fact this is what the STM32 driver does. Update the method name
to reflect this.
Tweak the docs a little and use 'flagsp' as the return argument, as is
common in driver model, to indicate it returns a value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The current method is a misnomer since it is also used (e.g. by stm32) to
update pull settings and open source/open drain.
Rename it and expand the documentation to cover a few more details.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
DM_VIDEO migration deadline is already expired, but around
80 Allwinner boards are still using video in a legacy way:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Convert the legacy video driver over to the DM_VIDEO framework. This is
a minimal conversion: it doesn't use the DT for finding its resources,
nor does it use DM clocks or DM devices for the outputs (LCD, HDMI, CVBS).
Tested in Bananapi M1+ Plus 1920x1200 HDMI out. (Jagan)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: rebase and smaller fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now when usbtty serial console is fixed in U-Boot enable CONFIG_USB_TTY for
Nokia RX-51 board by default.
Fix also USB product id as U-Boot ignores CONFIG_USBD_PRODUCTID macro and
include U-Boot string into USB product name to indicate usage of U-Boot.
CONFIG_CONSOLE_MUX is already used and U-Boot console is available for
all in/out devices. Therefore there is no need to have separate commands
'run sercon', 'run usbcon' and 'run vgacon', so remove them.
As space for U-Boot is limited to 256kB, enable CONFIG_OPTIMIZE_INLINING
and disable some other unused options so CONFIG_USB_TTY can be enabled.
Nokia RX-51 does not have easily accessible UART serial console so the only
option for easy debugging is to use device's keyboard+screen or this usbtty
serial console over USB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
With TPM2 we don't actually lock the TPM once verified boot is finished.
Instead we disable the platform hierarchy which serves the same purpose.
Add an implementation of this so we can safely boot into the kernel.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add support for this so that the TPM can be set up for use with
Chromium OS verified boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Take over the plain 'tpm_...' functions for use by the new TPM API. Rename
all the TPMv1 functions so they are called from the API.
Update the TPMv1 functions so that they are called from the API. Change
existing users to use the tpm1_ prefix so they don't need to go through
the API, which might introduce uncertainty.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
There are two different TPM standards. U-Boot supports both but each has
its own set of functions. We really need a single TPM API that can call
one or the other. This is not always possible as there are some
differences between the two standards, but it is mostly possible.
Add an API to handle this. So far it is not plumbed into the build and
only supports TPMv1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This state is not accessible to the running U-Boot but at present it is
allocated in the emulated SDRAM. This doesn't seem very useful. Adjust
it to allocate from the OS instead.
The RAM buffer is currently not freed, but should be, so add that into
state_uninit(). Update the comment for os_free() to indicate that NULL is
a valid parameter value.
Note that the strdup() in spl_board_load_image() is changed as well, since
strdup() allocates memory in the RAM buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
We provide os_malloc() and os_free() but not os_realloc(). Add this,
following the usual semantics. Also update os_malloc() to behave correctly
when passed a zero size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In drivers we use a family of printing functions including pr_err() and
pr_cont(). CONFIG_LOGLEVEL is used to control which of these lead to output
via printf().
Our logging functions allow finer grained control of output. So replace
printf() by the matching logging functions. The usage of CONFIG_LOGLEVEL
remains unchanged.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
