The nor->ready() and spansion_sr_ready() introduced earlier in this
series are used for multi-die package parts.
The nor->quad_enable() sets the volatile QE bit on each die.
The nor->erase() is hooked if the device is not configured to uniform
sectors, assuming it has 32 x 4KB sectors overlaid on bottom address.
Other configurations, top and split, are not supported at this point.
Will submit additional patches to support it as needed.
The post_bfpt/sfdp() fixes the params wrongly advertised in SFDP.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cypress chips support SPINOR_OP_EN4B(B7h) to enable 4-byte addressing mode.
Cypress chips support B8h to disable 4-byte addressing mode instead of
SPINOR_OP_EX4B(E9h).
This patch defines new opcode and updates set_4byte() to support
enable/disable 4-byte addressing mode for Cypress chips.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The spansion_sr_ready() reads status register 1 by Read Any Register
commnad. This function is called from Flash specific hook with die address
and dummy cycles to support multi-die package parts from Spansion/Cypress.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
For dual/quad die package devices from Spansion/Cypress, the device's
status needs to be checked by reading status registers in all dies, by
using Read Any Register command. To support this, a Flash specific hook
that can overwrite the legacy status check is needed.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some of Spansion/Cypress chips support volatile version of configuration
registers and it is recommended to update volatile registers in the field
application due to a risk of the non-volatile registers corruption by
power interrupt. This patch adds a function to set Quad Enable bit in CFR1
volatile.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some of Spansion/Cypress chips support Read/Write Any Register commands.
These commands are mainly used to write volatile registers and access to
the registers in second and subsequent die for multi-die package parts.
The Read Any Register instruction (65h) is followed by register address
and dummy cycles, then the selected register byte is returned.
The Write Any Register instruction (71h) is followed by register address
and register byte to write.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
We currently define the EFI support of an SMBIOS table as the third bit of
"BIOS Characteristics Extension Byte 1". The latest DMTF spec defines it
on "BIOS Characteristics Extension Byte 2".
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Remove superfluous assignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Since this flash doesn't have a Profile 1.0 table, the Octal DTR
capabilities are enabled in the post SFDP fixup, along with the 8D-8D-8D
fast read settings.
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency of 200Mhz.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.
The flash by default boots in a hybrid sector mode. Switch to uniform
sector mode on boot. Use the default 20 dummy cycles for a read fast
command.
The SFDP programming on some older versions of the flash was incorrect.
Fixes for that are included in the fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
On probe, the SPI NOR core will put a flash in 8D-8D-8D mode if it
supports it. But Linux as of now expects to get the flash in 1S-1S-1S
mode. Handing the flash to Linux in Octal DTR mode means the kernel will
fail to detect the flash.
So, we need to reset to Power-on-Reset (POR) state before handing off
the flash. A Software Reset command can be used to do this.
One limitation of the soft reset is that it will restore state from
non-volatile registers in some flashes. This means that if the flash was
set to 8D mode in a non-volatile configuration, a soft reset won't help.
This commit assumes that we don't set any non-volatile bits anywhere,
and the flash doesn't have any non-volatile Octal DTR mode
configuration.
Since spi-nor-tiny doesn't (and likely shouldn't) have
spi_nor_soft_reset(), add a dummy spi_nor_remove() for it that does
nothing.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
A Soft Reset sequence will return the flash to Power-on-Reset (POR)
state. It consists of two commands: Soft Reset Enable and Soft Reset.
Find out if the sequence is supported from BFPT DWORD 16.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This table is indication that the flash is xSPI compliant and hence
supports octal DTR mode. Extract information like the fast read opcode,
the number of dummy cycles needed for a Read Status Register command,
and the number of address bytes needed for a Read Status Register
command.
The default dummy cycles for a fast octal DTR read are set to 20. Since
there is no simple way of determining the dummy cycles needed for the
fast read command, flashes that use a different value should update it
in their flash-specific hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.
Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The spi-mem layer provides a spi_mem_supports_op() function to check
whether a specific operation is supported by the controller or not.
This is much more accurate than the hwcaps selection logic based on
SPI_{RX,TX}_ flags.
Rework the hwcaps selection logic to use spi_mem_supports_op().
To make sure the build doesn't break for boards not using CONFIG_DM_SPI,
add a simple SPI_{RX,TX}_ based hwcaps selection logic in spi-mem-nodm
similar to spi_mem_default_supports_op(). This change is only
compile-tested.
To avoid SPL size problems on the x530 board, the old hwcaps selection
is still kept around. Leaving the code in-place was getting difficult to
read and understand, so the code is restructured to have it all in one
isolated function. As a result of this, the parameter hwcaps to
spi_nor_setup() is no longer needed. Remove it.
Based on the Linux commit c76f5089796a (mtd: spi-nor: Rework hwcaps
selection for the spi-mem case, 2019-08-06)
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sometimes the information in a flash's SFDP tables is wrong. Sometimes
some information just can't be expressed in the SFDP table. So,
introduce the fixup hooks to allow tailoring settings for a specific
flash.
Three hooks are added: default_init, post_sfdp, and post_bfpt. These
allow tweaking the flash settings at different point in the probe
sequence. Since the hooks reside in nor->info, set that value just
before the call to spi_nor_init_params().
The hooks and at what points they are executed mimics Linux's spi-nor
framework. One major difference is that Linux puts the struct
spi_nor_fixups in nor->info. This is not possible in U-Boot because the
spi-nor-ids list is shared between spi-nor-core.c and spi-nor-tiny.c.
Since spi-nor-tiny shouldn't have those fixup hooks populated, add a
separate function that lets flashes populate their fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
nor->setup() can be used by flashes to configure settings in case they
have any peculiarities that can't be easily expressed by the generic
spi-nor framework. This includes things like different opcodes, dummy
cycles, page size, uniform/non-uniform sector sizes, etc.
Move related declarations to avoid forward declarations.
Inspired by the Linux kernel's setup() hook.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
spi_mem_default_supports_op() rejects DTR ops by default to ensure that
the controller drivers that haven't been updated with DTR support
continue to reject them. It also makes sure that controllers that don't
support DTR mode at all (which is most of them at the moment) also
reject them.
This means that controller drivers that want to support DTR mode can't
use spi_mem_default_supports_op(). Driver authors have to roll their own
supports_op() function and mimic the buswidth checks. Or even worse,
driver authors might skip it completely or get it wrong.
Add spi_mem_dtr_supports_op(). It provides a basic sanity check for DTR
ops and performs the buswidth requirement check. Move the logic for
checking buswidth in spi_mem_default_supports_op() to a separate
function so the logic is not repeated twice.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Controllers can use this function to perform basic sanity checking on
the spi-mem op.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
In xSPI mode, flashes expect 2-byte opcodes. The second byte is called
the "command extension". There can be 3 types of extensions in xSPI:
repeat, invert, and hex. When the extension type is "repeat", the same
opcode is sent twice. When it is "invert", the second byte is the
inverse of the opcode. When it is "hex" an additional opcode byte based
is sent with the command whose value can be anything.
So, make opcode a 16-bit value and add a 'nbytes', similar to how
multiple address widths are handled.
All usages of sizeof(op->cmd.opcode) also need to be changed to be
op->cmd.nbytes because that is the actual indicator of opcode size.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Each phase is given a separate 'dtr' field so mixed protocols like
4S-4D-4D can be supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Init GICv3 for V3U Falcon in early phase
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add board code for the R8A779A0 V3U Falcon board.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - various small rebase fixes and clean ups
The device_probe() function does the same thing as mtd_probe() and
mtd_probe() is only used in mtd_probe_uclass_mtd_devs(), where the
probing can be made simpler by using uclass_foreach_dev_probe macro.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Add support for parsing partitions defined in device-trees via the
`partitions` node with `fixed-partitions` compatible.
The `mtdparts`/`mtdids` mechanism takes precedence. If some partitions
are defined for a MTD device via this mechanism, the code won't register
partitions for that MTD device from OF, even if they are defined.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Add function for retrieving full node path of a given ofnode.
This uses np->full_name if OF is live, otherwise a call to
fdt_get_path() is made.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add functions ofnode_get_addr_size_index_notrans(), which is a
non-translating version of ofnode_get_addr_size_index().
Some addresses are not meant to be translated, for example those of MTD
fixed-partitions.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Based on the comment in socfpga_soc64_common.h, the intention is for
CONFIG_SYS_MEM_RESERVE_SECURE to be unused. However, in the code we do:
...
and that will evaluate to true. This leads to unwanted code being
compiled. Further, as CONFIG_SYS_MEM_RESERVE_SECURE has not been
migrated to Kconfig, this leads to a mismatch in the size of gd
depending on if we have or have not also had <configs/BOARD.h> also
included yet.
Remove the define as it's not needed.
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Chee Hong Ang <chee.hong.ang@intel.com>
Cc: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The original code is in the public domain. Licenses/README states that the
general license for U-Boot is GPL 2.0+. So we can mark the malloc code as
GPL 2.0+ too.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
On ARM64 secure OS can run as 64bit or 32bit that's why it is necessary to
record information about architecture that other code can read it and
properly pass it to TF-A and start in 64bit or 32bit mode.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit 63756575b4.
Since this commit a imx6qdl-pico board boots extremely slowly
in both SPL as well as U-Boot proper.
Fix this regression by reverting the offending commit for now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Add error callback in dfu stack to manage some board specific
behavior on DFU targets.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
RK3568 is a high-performance and low power quad-core application
processor designed for personal mobile internet device and AIoT
equipments.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
fdtoverlay (pxe_utils) require define fdtoverlay_addr_r env variable
for example sunxi-common.h meson64.h already have it.
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDLD78cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLhSB/0UqOd+Ujf2meiHU9yr
oOOCLxVTjTUfIZKLad/zwlj2Xqzsjs6XMawC95BgouvkQLmj/gwerRWcZPg9l7/X
hvb9VJi+iJoLRRpBPbeF3bMb92kCE+YZodFXyutlcY+Z0ZB9755zoVgR6ccKfksd
Xp2y8AFptfYQNZ1l0yb3lhm1261CldWALrGTjRpY2hQ8nEMbV8z6WUB1hAF9CECa
PGbKaiqm9OdktwHsLy4cYFFCuzkykn6T3P6ODineP7IxgEgZKTfJClSTFGY9S0GQ
kwd7K/7j0W3rI5NPknB+Fb4IFAaTs/oozR+5ml7j+2S3G5GXjSGx8zaSOmOZvpP3
KxwN
=/I5V
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for the 2021.10 cycle:
This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs
connected to MAC1 and MAC2. The second Aquantia PHY is located at a
different address on the MDIO bus compared to rev C (0x8 instead of 0x1).
Fix-up the Linux device tree to update the PHY address for the second
Aquantia PHY on boards revisions D and up. Also rename the PHY node to
reflect the changes.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
A system clock of 66MHz was chosen for the pg-wcom-ls102xa.
Compared to the Evalboard, this corresponds to a reduction of 1/3.
The system counter clock should have been reduced accordingly,
but that was not the case, so we had a system time that was
1/3 behind the real time.
This patch corrects the system counter clock to
8.333MHz = 66.667MHz / 8.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to improve power consumption ls102x allows to disable peripherals
that are not in use.
This patch follows SELI8 HW design description and disables peripherals
that are not in use in our designs, the same configuration is applicable
and for EXPU1.
This patch uses available hwconfig option for updating ls102x device
disable configuration.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The default behavior in the latest u-boot revisions is to rotate the
active net device to the next available if the requested link is not
established.
For our ls102x based devices this would mean that if active debug net
device is not available, u-boot will rotate and set the next net device
that is one of the estar adapters.
To return from this situation manual action to set correct ethact
adapter will be needed and this can be annoying when working in
debug mode.
Setting ethrotate=no will disable net adapter rotation and will make sure
that the primary adapter is always used.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In our designs we reserve PRAM area at the end of the RAM, and in order
this area to be visible and taken into account by the u-boot memory mgmt
CONFIG_PRAM has to be defined.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
From production view this is standard test executed during production on
all linux based foxmc cards.
On CENT2 HW defined memory region is zero means that some DDR accesses are
done by memory_post_dataline and memory_post_addrline but pattern tests
are skipped that's why mem_regions is fast there.
On ls102x for the complete DDR region of 1GiB memory_regions_post_test
takes approx. 4min and this is too much for production, so this patch
defines only 1MiB region as compromise.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
is used instead.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Michael Walle <michael@walle.cc> [for kontron-sl28]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards, according to the schematic and per the board I own, use an
M24256-BWDW6TP I2C EEPROM which requires two address bytes.
This fixes the 'mac' command which is used to program, among other
things, the MAC addresses for the ethernet interfaces on the board.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This driver no longer serves a purpose now that we have moved away from
CCF. Drop it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Now that there no separate PLL driver, we can no longer make the PLL
functions static. By moving the PLL driver in with the rest of the clock
code, we can make these functions static again. We still keep the pll
header for unit testing, but it is pretty reduced.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This is effectively a complete rewrite to remove all dependency on CCF.
The code is now smaller, and so is the binary. It also takes up less memory
at runtime (since we don't have to create 40 udevices). In general, I am
much happier with this driver as much of the complexity and late binding
has been removed.
The k210_*_params structs which were previously used to initialize CCF
clocks are now used as the complete configuration. Since we can write our
own division logic, we can now do away with several "half" clocks which
only existed to provide constant factors of two.
The clock IDs have been renumbered to remove unused clocks. This may not be
the last time they are renumbered, since we have diverged with Linux. There
are also still a few clocks left out which may need to be added back in.
In general, I have tried to leave out behavioral changes. However, there is
a small bugfix regarding ACLK. According to the technical reference manual,
its mux comes *after* its divider (which is present only for PLL0). This
would have required yet another intermediate clock to fix with CCF, but
with the new driver it is just 2 lines of code :)
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Since 291da96b8e ("clk: Allow clock defaults to be set during re-reloc
state for SPL only") it has been impossible to set clock defaults before
relocation. This is annoying on boards without SPL, since there is no way
to set clock defaults before U-Boot proper. In particular, the aisram rate
must be changed before relocation on the K210, since U-Boot will hang if we
try and change the rate while we are using aisram.
To get around this, extend the stage parameter to allow force setting
defaults, even if they would be otherwise postponed for later. A device
tree property was decided against because of the concerns in the original
commit thread about the overhead of repeatedly parsing the device tree.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports Falcon boot support for Microchip SAMA5D3 Xplained,
tested on raw MMC, and on raw NAND.
spl_start_uboot() is has the simplest possible implementation.
It doesn't test the environment because enabling environment support
currently causes the SPL to exceed its maximum size (64 KiB).
It doesn't check the serial for incoming characters either because
this functionality currently doesn't seem to work from the SPL
on this board.
Settings for Falcon boot from at FAT partition are also added to
avoid compile failures when CONFIG_SPL_OS_BOOT is enabled, but this
particular case is currently not functional as adding FAT and
partition support cause the SPL to be too big again.
Signed-off-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
Add support command for debugging K3 power domains. This is useful with
the HSM rearch setup, where power domains are directly controlled by SPL
instead of going through the TI SCI layer. The debugging support is only
available in the u-boot codebase though, so the raw register access
power domain layer must be enabled on u-boot side for this to work. By
default, u-boot side uses the TI SCI layer, and R5 SPL only uses the
direct access methods.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Normally, power domains are handled via TI-SCI in K3 SoCs. However,
SPL is not going to have access to sysfw resources, so it must control
them directly. Add driver for supporting this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add driver to support TI K3 generation SoC clocks. This driver registers
the clocks provided via platform data, and adds support for controlling
the clocks via DT handles.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add support for TI K3 SoC PLLs. This clock type supports
enabling/disabling/setting and querying the clock rate for the PLL. The
euclidean library routine is used to calculate divider/multiplier rates
for the PLLs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Current driver only supports registering fixed rate clocks from DT. Add
new API which makes it possible to register fixed rate clocks directly
from e.g. platform specific clock drivers.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
board_fit_image_post_process() passes only start and size of the image,
but type of the image is not passed. So pass fit and node_offset, to
derive information about image to be processed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Copy the best rational approximation calculation routines from Linux.
Typical usecase for these routines is to calculate the M/N divider
values for PLLs to reach a specific clock rate.
This is based on linux kernel commit:
"lib/math/rational.c: fix possible incorrect result from rational
fractions helper"
(sha1: 323dd2c3ed0641f49e89b4e420f9eef5d3d5a881)
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Add default fdtfile environment variable with value
marvell/armada-3720-turris-mox.dtb.
This can be useful for some boot scenarios.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable config options required to add support for USB Mass storage boot,
USB DFU boot, host and device modes in U-Boot.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-11-a-govindraju@ti.com
For USB DFU boot mode there is a limitation on the load address of boot
images that they have to be less than 0x70001000. Therefore, move the
SPL_TEXT_BASE address to 0x70000000.
Currently ATF is being loaded at 0x70000000, if the SPL is being loaded at
0x70000000 then ATF would overwrite SPL image when loaded. Therefore, move
the location of ATF to a latter location in SRAM, past the SPL image. Also
rearrange the EEPROM and BSS data on top of ATF.
Given below is the placement of various data sections in SRAM
┌──────────────────────────────────────┐0x70000000
│ │
│ │
│ │
│ SPL IMAGE (Max size 1.5 MB) │
│ │
│ │
│ │
├──────────────────────────────────────┤0x7017FFFF
│ │
│ SPL STACK │
│ │
├──────────────────────────────────────┤0x70192727
│ GLOBAL DATA(216 B) │
├──────────────────────────────────────┤0x701927FF
│ │
│ INITIAL HEAP (32 KB) │
│ │
├──────────────────────────────────────┤0x7019A7FF
│ │
│ BSS (20 KB) │
├──────────────────────────────────────┤0x7019F7FF
│ EEPROM DATA (2 KB) │
├──────────────────────────────────────┤0x7019FFFF
│ │
│ │
│ ATF (123 KB) │
│ │
│ │
├──────────────────────────────────────┤0x701BEBFB
│ BOOT PARAMETER INDEX TABLE (5124 B)│
├──────────────────────────────────────┤0x701BFFFF
│ │
│SYSFW FIREWALLED DUE TO A BUG (128 KB)│
│ │
├──────────────────────────────────────┤0x701DFFFF
│ │
│ DMSC CODE AREA (128 KB) │
│ │
└──────────────────────────────────────┘0x701FFFFF
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210604163043.12811-9-a-govindraju@ti.com
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Supported boot device types in iMX8MN: MMC, DHCP.
Add DISTRO_DEFAULTS config option and include the distro boot command
header file to enable full support of distro boot on i.MX8M Nano EVK (both
DDR and LPDDR derivatives).
Drop previous environment, which was targeting customized boot commands and
boot order.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.
Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.
Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
Uncompressed aarch64 kernel Image are rather large, increase the bootm
size limit to 64 MiB to cater for that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Usb needs IMXRT1050_CLK_USBOH3 clock to be enabled, so let's add it to
clock driver.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Lcd peripheral needs 2 different gates to be enable to work, so let's
introduce the missing one(LCDIF_PIX) and rename the existing one
(LCDIF_APB).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Currently the config options CONFIG_SYS_DFU_DATA_BUF_SIZE and
CONFIG_SYS_DFU_MAX_FILE_SIZE are being set in include/configs/<board>.h
files and also in <board_name>_defconfig files without a Kconfig option. It
is easier for users to set these configs in defconfig files than in config
header files as they are a part of the source code.
Add Kconfig symbols, and update the defconfigs by using tools/moveconfig.py
script.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
TFTP transfer size can be used to re-size the TFTP progress bar on
single line based on the server reported file size. The support for
this has been around from 2019, but it was never converted to proper
Kconfig.
While adding this new Kconfig, enable it by default for OMAP2+ and K3
devices also.
Signed-off-by: Tero Kristo <kristo@kernel.org>
At present if logging not enabled, log_info() becomes a nop. But we want
log output at the 'info' level to be akin to printf(). Update the macro to
pass the output straight to printf() in this case.
This mimics the behaviour for the log_...() macros like log_debug() and
log_info(), so we can drop the special case for these.
Add new tests to cover this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present print_buffer() outputs a hex dump but it is not possible to
place this dump in a string. Refactor it into a top-level function which
does the printing and a utility function that dumps a line into a string.
This makes the code more generally useful.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present print_hex_dump() only supports either 16- or 32-byte lines.
With U-Boot we want to support any line length up to a maximum of 64.
Update the function to support this, with 0 defaulting to 16, as with
print_buffer().
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the comments to the header file so people can find the function info
without digging in the implementation. Fix up the code style and add an
enum for the first arg.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test for this function, to cover the various features. Expand the
expect_str length to take acount of the ~300-bytes lines generated in one
case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This test predates the test framework in U-Boot. It uses #define DEBUG and
assert() to check the result. Update it to use the framework so it can
report failure constitent with other tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
If the console output buffer is exhausted, characters are silently dropped
from the end. Detect this condition and report an error when reading back
the characters.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new function lmb_is_reserved_flags to check if
an address is reserved with a specific flags.
This function can be used to check if an address was
reserved with no-map flags with:
lmb_is_reserved_flags(lmb, addr, LMB_NOMAP);
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add "flags" in lmb_property to save the "no-map" property of
reserved region and a new function lmb_reserve_flags() to check
this flag.
The default allocation use flags = LMB_NONE.
The adjacent reserved memory region are merged only when they have
the same flags value.
This patch is partially based on flags support done in Linux kernel
mm/memblock .c (previously lmb.c); it is why LMB_NOMAP = 0x4, it is
aligned with MEMBLOCK_NOMAP value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make it possible to invoke rescue boot from U-Boot console, without
having to press the factory reset button. This is needed when accessing
the device remotely, for example.
Achieve this by putting rescue command into `bootcmd_rescue` default
environment variable and setting some distroboot environment variables
to their default values when the factory button is pressed.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add dts support for fu740. The HiFive Unmatched support is based on
fu740 cpu and drivers in following patch set.
Signed-off-by: Green Wan <green.wan@sifive.com>
[greentime.hu: set fu740 speed to 1.2GHz]
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
"TCG PC Client Platform Firmware Profile Specification"
requires to measure every attempt to load and execute
a OS Loader(a UEFI application) into PCR[4].
This commit adds the PE/COFF image measurement, extends PCR,
and appends measurement into Event Log.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Replace CONFIG_HASH_CALCULATE by CONFIG_HASH
Fix conversions between pointers and u64.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
MLO has increased to a size greater than the allocated
128 kB in dfu_alt_info_emmc and _mmc.
Therefore, double the allocated size for MLO.raw in
the default environment.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210419065027.5834-1-a-govindraju@ti.com
ut_asserteq_strn is defined twice. Remove one definition.
Fixes: 33d7edfd5f ("test: Add a way to check part of a console line or skip it")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Remove qemu_mips boards because DM migration doesn't make sense.
The board support for qemu_mips is already marked as deprecated
in Qemu in favour of the Malta board. Also qemu_mips support
has been removed from Linux a long time ago.
The official replacement is the Malta board. The same Malta U-Boot
image can be used with Qemu and on physical hardware.
All combinations of Big Endian and Little Endian as well as 32 bit
and 64 bit are supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When building with LTO, the system libc's `errno` variable used in
arch/sandbox/cpu/os.c conflicts with U-Boot's `errno` (defined in
lib/errno.c) with the following error:
.../ld: errno@@GLIBC_PRIVATE: TLS definition in /lib64/libc.so.6
section .tbss mismatches non-TLS reference in
/tmp/u-boot.EQlEXz.ltrans0.ltrans.o
To avoid this conflict use different asm label for this variable when
CONFIG_SANDBOX is enabled.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add macro __efi_runtime_rodata, for const variables with similar purpose
as those using __efi_runtime_data.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Document the macros __efi_runtime and __efi_runtime_data in Sphinx
style.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When linking with LTO, the compiler complains about type mismatch of
variables `__efi_runtime_start`, `__efi_runtime_stop`,
`__efi_runtime_rel_start` and `__efi_runtime_rel_stop`:
include/efi_loader.h:218:21: warning: type of ‘__efi_runtime_start’
does not match original
declaration [-Wlto-type-mismatch]
218 | extern unsigned int __efi_runtime_start, __efi_runtime_stop;
| ^
arch/sandbox/lib/sections.c:7:6: note: ‘__efi_runtime_start’ was
previously declared here
7 | char __efi_runtime_start[0] __attribute__((section(".__efi_run
| ^
Change the type to char[] in include/efi_loader.h.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Increase the BOOTM_LEN to 32M . This would allow a bigger kernel image to be
booted, for example the multi_v7_defconfig.
Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
resetting ...
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We just need to initialize all the clocks pre-reloc. The clock driver
creates a bunch of devices, so we need to increase the pre-reloc malloc
arena.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This simplifies the PLL creation process, since we don't have to pass all
the parameters individually.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This patch changes the functioning of the detection of w1 devices.
The old way was a comparison between detected w1 and the ones described in
the device tree. Now it will just look for the driver matching the family
id of the w1 detected.
The patch is inspired from Maxime Ripard code.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
This patch adds a new "extension" command, which aims at detecting
extension boards connected to the hardware platform, and apply the
Device Tree overlays that describe the hardware present on those
extension boards.
In order to enable this mechanism, board-specific code must implement
the extension_board_scan() function that fills in a linked list of
"struct extension", each describing one extension board. In addition,
the board-specific code must select the SUPPORT_EXTENSION_SCAN Kconfig
boolean.
Based on this:
- "extension scan" makes the generic code call the board-specific
extension_board_scan() function to retrieve the list of detected
extension boards.
- "extension list" allows to list the detected extension boards.
- "extension apply <number>|all" allows to apply the Device Tree
overlay(s) corresponding to one, or all, extension boards
The latter requires two environment variables to exist and set one variable
to run:
- extension_overlay_addr: the RAM address where to load the Device
Tree overlays
- extension_overlay_cmd: the U-Boot command to load one overlay.
Indeed, the location and mechanism to load DT overlays is very setup
specific.
- extension_overlay_name: set by the command: the name of the DT which
will be load during the execution.
When calling the command described in the extension_overlay_cmd
variable, the variable extension_overlay_name will be defined. So a
typical extension_overlay_cmd will look like this:
extension_overlay_cmd=load mmc 0:1 $extension_overlay_addr /boot/$extension_overlay_name
Here is an example on how to use it:
=> run loadfdt
=> fdt addr $fdtaddr
=> setenv extension_overlay_addr 0x1000
=> setenv extension_overlay_cmd 'load mmc 0:1 ${extension_overlay_addr} /boot/${extension_overlay_name}'
=> extension scan
Found 1 extension board(s).
=> extension apply 0
519 bytes read in 3 ms (168.9 KiB/s)
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Move the fdt_valid function to fdt_support.
This changes allow to be able to test the validity of a devicetree in
other c files.
Update code syntax.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Enable CONFIG_DM_ETH in configs/pm9263_defconfig
Drop legacy initialization in board/ronetix/pm9263.c
Remove network related setting from include/configs/pm9263.h
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
With AM64x supporting only K3_NAV_RINGACC_RING_MODE_RING or the exposed
ring mode, all other K3 SoCs have also been moved to this common
baseline. Therefore drop other modes such as
K3_NAV_RINGACC_RING_MODE_MESSAGE (and proxy) to save on SPL footprint.
There is a saving of ~800 bytes with this change for am65x_evm_r5_defconfig.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
AM64 dual mode rings are modeled as pair of Rings objects which has common
configuration and memory buffer, but separate real-time control register
sets for each direction mem2dev (forward) and dev2mem (reverse).
AM64 rings must be requested only using k3_ringacc_request_rings_pair(),
and forward ring must always be initialized/configured. After this any
other Ringacc APIs can be used without any callers changes.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Update struct ti_sci_msg_rm_udmap_tx_ch_cfg_req to latest ABI to support
AM64x BCDMA Block copy channels.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Now that single defconfig can be used for booting AM64 EVM and SK,
default device tree will not work for selecting dtb for kernel.
Update the env to select right dtb based on eeprom.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Current BSS allocation of SPL is as below:
size spl/u-boot-spl
text data bss dec hex filename
144572 5484 1752 151808 25100 spl/u-boot-spl
But 20KB is allocated currently for BSS. Reduce it to 4KB and
save some space for stack.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add pinctrl macros for AM64 SoC. These macro definitions are similar to
that of previous platforms, but adding new definitions to avoid any
naming confusions in the soc dts files.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
By declaring board-specific board_fdt_chosen_bootargs() the kernel
command line arguments can be adjusted before injecting to flat dt
chosen node.
Signed-off-by: Niko Mauno <niko.mauno@vaisala.com>
It can be useful to use the same U-Boot binary for multiple purposes,
say the normal one, one for developers that allow breaking into the
U-Boot shell, and one for use during bootstrapping which runs a
special-purpose bootcmd. Or one can have several board variants that
can share almost all boot logic, but just needs a few tweaks in the
variables used by the boot script.
To that end, allow the control dtb to contain a /config/enviroment
node (or whatever one puts in fdt_env_path variable), whose
property/value pairs are used to update the run-time environment after
it has been loaded from its persistent location.
The indirection via fdt_env_path is for maximum flexibility - for
example, should the user wish (or board logic dictate) that the values
in the DTB should no longer be applied, one simply needs to delete the
fdt_env_path variable; that can even be done automatically by
including a
fdt_env_path = "";
property in the DTB node.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This has the uclass enforce calling detect() before other methods. This
allows drivers to cache information in detect() and perform (cheaper)
retrieval in the other accessors. This also modifies the only instance
where this sequencing was not followed.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Prevent shell access on boot failure by entering an infinite
loop.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Minor cosmetic changes to unify `CONFIG_EXTRA_ENV_SETTINGS'
indentation between Bx50v3 and PPD to make comparison and
review easier and simplify the default boot command.
Signed-off-by: Ian Ray Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
binman FMAP improvements
minor test improvements and fixes
minor dm improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmCKoLERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYCpgf/ROfOg76k18PdWcQTZr10CnU0iqTaOyYx
129hvb4n4bx4Q7Zr/HrWT6y7vvD01NOiNCwSX8qdF7S1bqs2/2AM+Yk/vLimXVOg
UDGXGRABkbHQFVMzBUSmlmQvKoG5G6AhS6/5/F7q4jj+QCVMGarves7G7ImhFOFw
6WKeNGv6FWX4UPSxm0TDJETiIqURNZOsu2vU9DmkR/b1eY13/qf/9J4zzEP1DaJt
7PrKmyblRhPlMsi59EjNyEQOnY/A17en8Ik3Zt336tLPELlczRc4Xp8HslQsy2i3
o457il6x8kl828oVwm3Sx4R/UvM8+qE1jWRcPA7vWrxCy3+AqDcTfQ==
=tiPD
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-29apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm
buildman environment fix
binman FMAP improvements
minor test improvements and fixes
minor dm improvements
Add a reference for the TPM event types and provide missing constants.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add functions to add size of addresses in the device tree using ofnode
references.
If the size is not set, return FDT_SIZE_T_NONE.
Signed-off-by: Chen Guanqiao <chenguanqiao@kuaishou.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In CP115, comphy4 can be configured into SFI port1
(in addition to SFI0). This patch adds the option
described above.
In addition, rename all existing SFI/XFI references:
COMPHY_TYPE_SFI --> COMPHY_TYPE_SFI0
No functional change for exsiting configuration.
Change-Id: If9176222e0080424ba67347fe4d320215b1ba0c0
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Even if comphy types of SATA2/SATA3/SGMII3 and comphy speeds of
1.5G/3G/6.25G were referenced in the driver non configuration (dts)
was using it.
This patch removes unused definitions.
Change-Id: I53ed6f9d3a82b9d18cb4e488bc14d3cf687f9488
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
This patch adds support for running RX training using new command called
"rx_training"
Usage:
rx_training - rx_training <cp id> <comphy id>
RX training allows to improve link quality (for SFI mode)
by running training sequence between us and the link partner,
this allows to reach better link quality then using static configuration.
Change-Id: I818fe67ccaf19a87af50d4c34a9db7d6802049a5
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.
This patch does the following changes:
- PHY_TYPE_XX --> COMPHY_TYPE_XX
- PHY_SPEED_XX --> COMPHY_SPEED_XX
This improves readability, no functional change.
Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
- For some Marvell SoCs, like armada-3700, there are both
USB host and device controller, but on PHY level the
configuration is the same.
- The new type supports both USB device and USB host
- This patch is cherry-picked from u-boot-2015 as-is.
Change-Id: I01262027edd8ec23391cff6fb409b3009aedfbb9
Signed-off-by: jinghua <jinghua@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Add support for regulator-force-boot-off DT property.
This property can be used by the board/device drivers for
turning off regulators on early init stages as pre-requisite
for the other components initialization.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Update R40 .dts{,i} and dt-binding headers to current version from kernel.
Files taken from Linux 5.12-rc1 release
(commit fe07bfda2fb9cdef8a4d4008a409bb02f35f1bd8)
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Enable EFI capsule update features to be enabled by default also with all
dfu valid options for ZynqMP.
This feature was tested on Xilinx ZynqMP zcu104 board with defining
dfu_alt_info="mmc 0:1=boot.bin fat 0 1;u-boot.itb fat 0 1"
and
dfu_alt_info="sf 0:0=boot.bin raw 0 0x50000;u-boot.itb raw 0x80000
0x500000".
There is a need to increase malloc size for getting dfu mmc to work.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
Update R40 .dts{,i} and dt-binding headers to current version from kernel.
Files taken from Linux 5.12-rc1 release
(commit fe07bfda2fb9cdef8a4d4008a409bb02f35f1bd8)
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
-----BEGIN PGP SIGNATURE-----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=JwRN
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2021-04-24' of https://source.denx.de/u-boot/custodians/u-boot-mips
- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
Add support for usb dfu & thor to distro boot on zynq platform.
Add 60s timeout of dfu-utils to start transaction. Remove
DFU_ALT_INFO_RAM as we use bootcmd_usb_dfu instead of dfu_ram.
Remove DFU_ALT_INFO_MMC as part of distro boot cleanup.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change "dfu_usb" to "usb_dfu" for better representation and change
required macros. Add 60s timeout of dfu-utils to start transaction.
Add support for usb thor to distro boot. Remove DFU_ALT_INFO_RAM
as we use bootcmd_usb_dfu instead of dfu_ram.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dfu ram info is wired in connection to Linux kernel and certain setup.
We should change this to be more generic as others command. That's why
using boot via script is the way to go.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In usb boot mode distro boot should select usb device as primary boot
device instead of usb host. So make usb dfu as primary boot device. But do
not list it in boot_targets as fallback option because it is not classic
mode for booting. Using 60s timeout by default should be enough time for
dfu-utils to start transaction. In case none needs this please change
timeout value in the command or disable CONFIG_DFU_TIMEOUT.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add 2 configs CONFIG_LMB_MEMORY_REGIONS and CONFIG_LMB_RESERVED_REGIONS
to change independently the max number of the regions in lmb
library.
When CONFIG_LMB_USE_MAX_REGIONS=y, move the lmb property arrays to
struct lmb and manage the array size with the element 'max' of struct
lmb_region; their are still allocated in stack.
When CONFIG_LMB_USE_MAX_REGIONS=n, keep the current location in
struct lmb_region to allow compiler optimization.
Increase CONFIG_LMB_RESERVED_REGIONS is useful to avoid lmb errors in
bootm when the number of reserved regions (not adjacent) is reached:
+ 1 region for relocated U-Boot
+ 1 region for initrd
+ 1 region for relocated linux device tree
+ reserved memory regions present in Linux device tree.
The current limit of 8 regions is reached with only 5 reserved regions
in DT.
see Linux kernel commit bf23c51f1f49 ("memblock: Move memblock arrays
to static storage in memblock.c and make their size a variable")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As in lmb_region, cnt < max and in the lmb library
use region[i] only with i in 0...cnt, this region array size
can be reduced by 1 element without overflow.
This patch allows to reduce the struct lmb size.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add a max parameter in lmb_region struct to handle test
in lmb_add_region without using the MAX_LMB_REGIONS
define.
This patch allows to modify these size independently for
memory of reserved regions in the next patches.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove the unused field size of struct lmb_region as it is initialized to 0
and never used after in lmb library.
See Linux kernel commit 4734b594c6ca ("memblock: Remove memblock_type.size
and add memblock.memory_size instead")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Adds support for:
* PSCI_FEATURES, which was introduced in PSCI 1.0. This provides API
that allows discovering whether a specific PSCI function is implemented
and its features.
* SYSTEM_RESET2, which was introduced in PSCI 1.1, which extends existing
SYSTEM_RESET. It provides support for vendor-specific resets, providing
reset_type as an additional param.
For additional details visit [1].
Implementations of some functions were borrowed from Linux PSCI driver
code [2].
[1] https://developer.arm.com/documentation/den0022/latest/
[2] drivers/firmware/psci/psci.c
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
So far we were defining a somewhat confusing PHYS_SDRAM_1_SIZE variable,
which originally was only used for setting the memtest boundaries. This
definition in highbank.h has been removed about a year ago (moved to
Kconfig), so we also don't need the hard-coded size definition any longer.
Get rid of the misleading memory size definition, which was actually wrong
anyway (it's 4088 MB for those machines with just 4GB of DRAM).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
All Calxeda machines are actually a poster book example of device tree
usage: the DT is loaded from flash by the management processor into
DRAM, the memory node is populated with the detected DRAM size and this
DT is then handed over to the kernel.
So it's a shame that U-Boot didn't participate in this chain, but
fortunately this is easy to fix:
Define CONFIG_OF_CONTROL and CONFIG_OF_BOARD, and provide a trivial
function to tell U-Boot about the (fixed) location of the DTB in DRAM.
Then enable DM_SERIAL, to let the PL011 driver pick up the UART platform
data from the DT. Also define AHCI, to bring this driver into the driver
model world as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far on Highbank/Midway machines U-Boot only ever uses 512MB of DRAM,
even though the machines have typically 4GB and 8GB, respectively.
That means that so far we didn't need an extra limit for placing the DTB
and initrd, as the 512MB are lower than the kernel's limit ("lowmem",
typically 768MB).
With U-Boot now needing to learn about the actual memory size (to
correctly populate the EFI memory map), it might relocate fdt and initrd
to the end of DRAM, which is out of reach of the kernel.
So add limiting values to the fdt_high and initrd_high environment
variables, to prevent U-Boot from using too high addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_SUPPORT_RAW_INITRD out of the octeontx_common header
and into the defconfig files.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Fixes IDE issues found on the Malta board under Qemu:
1) DMA implied commands were sent to the controller in stead of the PIO
variants. The rest of the code is DMA free and written for PIO operation.
2) direct pointer access was used to read and write the registers instead
of the inb/inw/outb/outw functions/macros. Registers don't have to be
memory mapped and ATA_CURR_BASE() does not have to return an offset from
address zero.
3) Endian isues in ide_ident() and reading/writing data in general. Names
were corrupted and sizes misreported.
Tested malta_defconfig and maltael_defconfig to work again in Qemu.
Signed-off-by: Reinoud Zandijk <reinoud@NetBSD.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This reverts commit 38d6b7ebda.
struct global_data contains a pointer to the bd_info structure. This
pointer was populated spl_set_bd() to a pre-allocated bd_info in the
".data" section. The referenced commit replaced this mechanism to one
that uses malloc(). That new mechanism is only used if SPL_ALLOC_BD=y.
which very few boards do.
The result is that (struct global_data)->bd is NULL in SPL on most
platforms. This breaks falcon mode, since arch_fixup_fdt() tries to
access (struct global_data)->bd and set the "/memory" node in the
devicetree. The result is that the "/memory" node contains garbage
values, causing linux to panic() as it sets up the page table.
Instead of trying to fix the mess, potentially causing other issues,
revert to the code that worked, while this change is reworked.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is a patchset which makes away with the .bind() controller indexing
workaround which was broken since before v2021.04, and then adds PHY
support and MX8M support on top of that. Better add it into the release
early to get as much testing as possible done, because this really does
a lot of changes to the ehci-mx6 driver.
Enable USB host support on MX8MM Verdin.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add ENV_ERASE_PTR macro to handle erase opts and remove the associated
ifdef.
This patch is a extension of previous commit 82b2f41357 ("env_internal.h:
add alternative ENV_SAVE_PTR macro").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
If one of the reads fails when importing redundant environments (a
single read failure), the env_flags wouldn't get initialized in
env_import_redund(). If a user then calls saveenv, the new environment
will have the wrong flags value. So on the next load the new environment
will be ignored.
While debugging this, I also noticed that env/sf.c was not correctly
handling a single read failure, as it would not check the crc before
assigning it to gd->env_addr.
Having a special error path for when there is a single read failure
seems unnecessary and may lead to future bugs. Instead collapse the
'single read failure' error to be the same as a 'single crc failure'.
That way env_check_redund() either passes or fails, and if it passes we
are guaranteed to have checked the CRC.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for devices with R40 dual rank DRAM, and asymmetric
A64 DRAM devices like the Pinephone/3GB.
Also we enable automatic gzipped kernel support, and allow scripted
DT overlay support. The rest of the patches are cleanups, but also
some sunxi-specific preparatory patches for USB3.0 and improved HDMI
support. The bulk of those changes will go through other trees, though.
Build-tested for all 156 sunxi boards, and boot tested on a A64, A20, R40,
H5, H6 and H616 board. USB, SD card, eMMC, HDMI and Ethernet all work
there (where applicable), with the exception of Ethernet on the H5. Since
this is already broken in v2021.04, I will send a separate fix.
The "booti" command to load arm64 Linux kernels supports automatic
decompression of zipped kernel images, but relies on some environment
variables to point to usable buffer RAM.
Add those variables and let them point to some default values, that
should cover most use-cases.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit 69076dff22 ("cmd: pxe: add support for FDT overlays") added
support for loading DT overlay files to PXE boot. However, it needs
additional environment variable which points to memory location which
can be used to temporary store overlay data.
Add it and in the process unify alignment using spaces and fix comment.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However, this call is missing for ls1012a boards. As a result EFI
boot doesn’t work. Fix this issue by removing custom definition of
scan_dev_for_boot and use the default definition instead.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With all preparations in place, switch over to DM_SERIAL.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present we decode simple bus <ranges> using the following assumption:
- parent #address-cells 1
- child #address-cells 1
- child #size-cells 1
However this might not always be the case.
Update to use fdt_addr_t and fdt_size_t in 'struct simple_bus_plat', and
use fdt_read_ranges() to correctly decode it according to the actual
parent and child #address-cells / #size-cells under a Kconfig option
CONFIG_SIMPLE_BUS_CORRECT_RANGE which can be turned on for any board
that needs it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The DSA sandbox driver is used for unit testing the DSA class code.
It implements a simple 2 port switch plus 1 CPU port, and uses a
very simple tag to identify the ports.
The DSA sandbox device is connected via CPU port to a regular Ethernet
sandbox device, called 'dsa-test-eth, managed by the existing eth
sandbox driver. The 'dsa-test-eth' is not intended for testing the
eth class code however, but it is used to emulate traffic through the
'lan0' and 'lan1' front pannel switch ports. To achieve this the dsa
sandbox driver registers a tx handler for the 'dsa-test-eth' device.
The switch ports, labeled as 'lan0' and 'lan1', are also registered
as eth devices by the dsa class code this time. So pinging through
these switch ports is as easy as:
=> setenv ethact lan0
=> ping 1.2.3.5
Unit tests for the dsa class code were also added. The 'dsa_probe'
test exercises most API functions from dsa.h. The 'dsa' unit test
simply exercises ARP/ICMP traffic through the two switch ports,
including tag injection and extraction, with the help of the dsa
sandbox driver.
I took care to minimize the impact on the existing eth unit tests,
though some adjustments needed to be made with the addition of
extra eth interfaces used by the dsa unit tests. The additional eth
interfaces also require MAC addresses, these have been added to the
sandbox default environment.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20210216224804.3355044-5-olteanv@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce a helper API ofnode_phy_is_fixed_link() to detect whether
the ethernet controller connects to a fixed-link pseudo-PHY device.
Note there are two ways to describe a fixed PHY attached to an
Ethernet device:
- the new DT binding, where 'fixed-link' is a sub-node of the
Ethernet device
- the old DT binding, where 'fixed-link' is a property with 5
cells encoding various information about the fixed PHY
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.
It is based on NXP LS1021 SoC and it provides following interfaces:
- IFC interface for NOR, NAND and external FPGA's
- 1 x RGMII ETH for debug purposes
- 2 x SGMII ETH for management communication via back-plane
- 1 x uQE HDLC for management communication via back-plane
- 1 x I2C for peripheral devices
- 1 x SPI for peripheral devices
- 1 x UART for debug logging
It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It's not always desirable to use 'keydir' and some ad-hoc heuristics
to get the filename of the signing key. More often, just passing the
filename is the simpler, easier, and logical thing to do.
Since mkimage doesn't use long options, we're slowly running out of
letters. I've chosen '-G' because it was available.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mkimage supports rsa2048, and rsa4096 signatures. With newer silicon
now supporting hardware-accelerated ECDSA, it makes sense to expand
signing support to elliptic curves.
Implement host-side ECDSA signing and verification with libcrypto.
Device-side implementation of signature verification is beyond the
scope of this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
fdt_add_bignum() is useful for algorithms other than just RSA. To
allow its use for ECDSA, move it to a common file under lib/.
The new file is suffixed with '-libcrypto' because it has a direct
dependency on openssl. This is due to the use of the "BIGNUM *" type.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
rsa-checksum.c sontains the hash_calculate() implementations. Despite
the "rsa-" file prefix, this function is useful for other algorithms.
To prevent confusion, move this file to lib/, and rename it to
hash-checksum.c, to give it a more "generic" feel.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We move qfw into its own uclass and split the PIO functions into a
specific driver for that uclass. The PIO driver is selected in the
qemu-x86 board config (this covers x86 and x86_64).
include/qfw.h is cleaned up and documentation added.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This introduces strlcat, which provides a safer interface than strncat. It
never copies more than its size bytes, including the terminating nul. In
addition, it never reads past dest[size - 1], even if dest is not
nul-terminated.
This also removes the stub for dwc3 now that we have a proper
implementation.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement voltage regulators interfaced by the SCMI voltage domain
protocol. The DT bindings are defined in the Linux kernel since
SCMI voltage domain and regulators patches [1] and [2] integration
in v5.11-rc7.
Link: [1] 0f80fcec08
Link: [2] 2add5cacff
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
It's an old bringup board with out upstream Linux or L4T support
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Similar to support for SHA1 and SHA256, allow the use of hardware hashing
engine by enabling the algorithm and setting CONFIG_SHA_HW_ACCEL /
CONFIG_SHA_PROG_HW_ACCEL.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Checkpatch complains about:
ERROR: "foo * bar" should be "foo *bar"
and
CHECK: Alignment should match open parenthesis
Signed-off-by: Joel Stanley <joel@jms.id.au>
The optee_copy_fdt_nodes is only used to copy op-tee nodes
of U-Boot device tree (from gd->fdt_blob when OF_LIVE is not activated)
to external device tree but it is not compatible with OF_LIVE.
This patch migrates all used function fdt_ functions to read node on
old_blob to ofnode functions, compatible with OF_LIVE and remove this
parameter "old_blob".
The generated "device tree" is checked on stm32mp platform with OF_LIVE
activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add power_max77696_init() function.
Since warp doesn't support DM, the keeping its code in board file is
better than maintainig the file of driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This PWM is used in rk3399-gru-bob and rk3399-gru-kevin to control
the display brightness. We can only change the duty cycle, so on
set_config() we just try to match the duty cycle that dividing duty_ns
by period_ns gives us. To disable, we set the duty cycle to zero while
keeping the old value for when we want to re-enable it.
The cros_ec_set_pwm_duty() function is taken from Depthcharge's
cros_ec_set_bl_pwm_duty() but modified to use the generic pwm type.
The driver itself is very loosely based on rk_pwm.c for the general pwm
driver structure.
The devicetree binding file is from Linux, before it was converted to
YAML at 5df5a577a6b4 ("dt-bindings: pwm: Convert google,cros-ec-pwm.txt
to YAML format") in their repo.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PWM device provided by Chrome OS EC doesn't really support anything
other than setting a relative duty cycle. To support it as a backlight,
this patch makes the PWM period optional in the device tree and pretends
the valid brightness range is its period_ns.
Also adds a sandbox test for a PWM channel that has a fixed period,
checking that the resulting duty_cycle matches on a set_config() even if
the requested period_ns can't be set.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. It is also the only ARCH_T2081 board so remove that support
as well.
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <linuxfae@technexion.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Thomas Weber <weber@corscience.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM by the deadline.
Remove them.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Erik van Luijk <evanluijk@interact.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The mvsata_ide driver was due for DM conversion by v2019.07. As that
has long passed, remove the driver and disable it in the boards which
had enabled it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. In order to
convert to using the DWC SATA driver under DM further migrations are
required.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Signed-off-by: Tom Rini <trini@konsulko.com>
* UEFI spec 2.9 introduced a new memory type EFI_UNACCEPTED_MEMORY_TYPE.
Add it to enum EFI_MEMORY_TYPE.
* Add missing EFI_MEMORY_CPU_CRYPTO constant
* Improve description of EFI_PERSISTENT_MEMORY_TYPE
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Avoid 'make htmldocs' build warnings:
./include/linker_lists.h:224: warning:
Function parameter or member '_type' not described in 'll_entry_ref'
./include/linker_lists.h:224: warning:
Function parameter or member '_name' not described in 'll_entry_ref'
./include/linker_lists.h:224: warning:
Function parameter or member '_list' not described in 'll_entry_ref'
Fixes: 851144350b ("linker_lists: Allow use in data structures")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
* Avoid a warning: "Incorrect use of kernel-doc format".
* Remove duplicate text.
* Clarify usage of EFI_SETTING_VIRTUAL_ADDRESS_MAP.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
-----BEGIN PGP SIGNATURE-----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=4VxR
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210409' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
A now removed comment promises to "limit SYSRAM usage to first 128 KB".
This would imply that only SYSRAM from 0x2ffc0000 - 0x2ffe0000 would be
used. This is not what happens at all.
First, SPL_MAX_SIZE is referenced from SPL_TEXT_BASE, which on all
existing configs is set to 0x2ffc2500, not SYSRAM_BASE (0x2ffc0000).
Some of it is in the first 128 KiB and some of it is in the second
128 KiB chunk of SYSRAM.
Second, SPL_MAX_SIZE, does not restrict the BSS size. While a valiant
attempt is made via SPL_BSS_MAX_SIZE, the value of 0x00100000 is much
larger than SYSRAM, and doesn't account for the non-BSS sections.
Because we're putting the .text and .bss in the same boat, the correct
way to limit them together is via SPL_MAX_FOOTPRINT. With the current
SPL_TEXT_BASE, we couldn't limit even a very basic SPL to the first
128 KiB, and there is no technical reason to do so. Because of this,
simply allow the SPL to use all SYSRAM.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
CONFIG_SPL_BSS_START_ADDR is only used on a few mach- linker scripts.
stm32mp1 uses the generic script under arch/arm/cpu/u-boot-spl.lds,
which does not make use of this definition.
The SPL BSS starts in SRAM, right after .text, .rodata, .data, and
.u_boot_list. A very short version of the STM32MP1 memory map is:
* SYSRAM: 2ffc0000 - 30000000 <- all of SPL is here
* DRAM: c0000000+
0xC0200000 is a DRAM address, and has nothing to do with SPL. It is
just very misleading to have it next to CONFIG_SPL_BSS_MAX_SIZE, or to
have it at all.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for
loading images"), FIT images must be malloc()'d before being loaded.
The old size of 1 MiB is suitable for FIT images with u-boot and an
FDT, but something containing a linux kernel is almost sure to fail.
It's safe to extend malloc all the way to 0xc2000000, but no further.
Linux likes to be loaded at 0xc2000000, so we use that as our cutoff
point. This gives us 29 MiB of malloc() space, which suited for more
complex FIT images including several DTBs, kernel, and OP-TEE images.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
All these files are add for support rt-thread art-pi board
- add board/st/stm32h750-art-pi, defconfig, header support for u-boot
for more information about art-pi, please goto:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patchset has following changes:
- introduce stm32h750.dtsi to support stm32h750 value line
- add pin groups for usart3/uart4/spi1/sdmmc2
- add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
- add stm32h750i-art-pi.dts to support art-pi board
- add stm32h750i-art-pi-u-boot.dtsi to support art-pi board (u-boot)
art-pi board component:
- 8MiB qspi flash
- 16MiB spi flash
- 32MiB sdram
- ap6212 wifi&bt&fm
the detail board information can be found at:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enabled "fsl,legacy-bch-geometry" in U-Boot device tree overlay
to match the legacy BCH geometry layout, which mainline Linux
applies when "fsl,use-minimum-ecc" is not specified in the device
tree.
Reinstated SYS_NAND_ONFI_DETECTION, which when disabled, masked
the mismatch on SOMs with Winbond NAND flash chips.
Signed-off-by: Niel Fourie <lusus@denx.de>
For FSL_USDHC, it do not implement VENDORSPEC_CKEN/PEREN/HCKEN/IPGEN, these
are reserved bits. Instead, use VENDORSPEC_FRC_SDCLK_ON to gate on/off the
card clock output.
After commit b5874b552f ("mmc: fsl_esdhc_imx: add wait_dat0() support"),
we meet SD3.0 card can't work at UHS mode, mmc_switch_voltage() fail because
the second mmc_wait_dat0 return -ETIMEDOUT. According to SD spec, during
voltage switch, need to gate off/on the card clock. If not set the FRC_SDCLK_ON,
after CMD11, hardware will gate off the card clock automatically, so card do
not detect the clock off/on behavior, so will draw the data0 line low until
next command.
Fixes: b5874b552f ("mmc: fsl_esdhc_imx: add wait_dat0() support")
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Convert the UDOO board to use DM_ETH.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block, DM MMC and DM SATA support on iMX6 Udoo
convert board code to match the DM support.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since Toradex provides the full set of overlays for Linux kernel
for display interfaces for both Apalis iMX6Q and Colibri iMX6DL
modules, the video= settings are obsolete. Remove them.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
All the other boards have tdxargs specified for setting manual kernel
command-line arguments. Add them also to NAND-based boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for loading images")'
changed the way buffer allocation worked for SPL to a more flexible
method.
For venice this caused breakage that is resolved by increasing the size
of CONFIG_SYS_SPL_MALLOC_SIZE as the current FIT slighly exceeds 512KiB.
Additionally remove the unnecessary comment on CONFIG_SPL_BSS_MAX_SIZE
and CONFIG_SYS_SPL_MALLOC_SIZE as the size is obvious from the define.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model for MTD and NAND support allowing us to remove
the iomux, init, and most of the static configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable dm support for USB (which also requires dm support for fixed
regulators used for vbus enable) and remove usb iomux which is no
longer needed.
We can remove the handling of otgpwr_en gpio as this is defined in
dt as usbotg vbus-supply but we need to keep the handling of
USB_HUB_RST# for boards that have a USB HUB as that isn't defined in
the dt's currently.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add DEK blob encapsulation support for IMX8M through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application call.
U-boot sends and receives the DEK and the DEK blob binaries through OP-TEE
dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add function to send mailbox command via SMC to get usercode from SDM.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Remove unused SMC function ID 61 and 62.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
In preparation to add SiFive Unmatched board support, let's rename
the existing fu540 board to unleashed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This define was left over from a previous revision, and was never used.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
In i.MX8M platforms the secure memory block has a newer version
than those used in i.MX6/7 platforms, this patch update the driver
to use the correct registers offsets.
Signed-off-by: Aymen Sghaier <aymen.sghaier@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enabling CAAM driver for i.MX8M platforms, a 64 bits architecture,
lead to casting warnings: from/to pointer to/from integer with
different size. This patch fix these warnings
Signed-off-by: Aymen Sghaier <aymen.sghaier@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
U-Boot can instantiate CAAM RNG if needed by crypto operations.
Call sec_init() prior running a blob operation to ensure
RNG is correctly instantiated.
Make sure CAAM clock is enabled and check if a job ring is
available for that operation.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This code was originally developed by Raul Cardenas <raul.casas@nxp.com>
and modified to be applied in U-Boot imx_v2017.03.
More information about the initial submission can be seen
in the link below:
https://lists.denx.de/pipermail/u-boot/2016-February/245273.html
i.MX7D has an a protection feature for Manufacturing process.
This feature uses asymmetric encryption to sign and verify
authenticated software handled between parties. This command
enables the use of such feature.
The private key is unique and generated once per device.
And it is stored in secure memory and only accessible by CAAM.
Therefore, the public key generation and signature functions
are the only functions available for the user.
The manufacturing-protection authentication process can be used to
authenticate the chip to the OEM's server.
Command usage:
Print the public key for the device.
- mfgprot pubk
Generates Signature over given data.
- mfgprot sign <data_address> <data_size>
Signed-off-by: Raul Ulises Cardenas <raul.casas@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This is a straightforward conversion of the old, non-dm driver. It was
done in-place as the deadline for non-dm MMC has passed. Previous
commits ensured that no board depends on the old, non-dm variant. Tested
on a Kirkwood based board with eMMC.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Tested-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Stefan Roese <sr@denx.de>
CC: Gerald Kerma <drEagle@doukki.net>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This will be replaced with the driver model version
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Stefan Roese <sr@denx.de>
CC: Tom Rini <trini@konsulko.com>
Unfortunately this board has no DM support at all. We are also way past
the deadline for driver model support for various devices on this board.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Stefan Roese <sr@denx.de>
These boards use an MMC driver that does not use this definition
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Stefan Roese <sr@denx.de>
CC: Mario Six <mario.six@gdsys.cc>
CC: Dennis Gilmore <dgilmore@redhat.com>
Call 'run update_uboot' to fetch u-boot-spl.kwb via TFTP and write it
into the correct SPI flash location. The latter's size is defined in
DS414's DTB file, so hard-coding it should be acceptable here.
Take care to not append garbage from RAM to the written image and to
stay within assigned flash boundaries even if an oversized image was
fetched.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Move the relevant bits from ds109.{c,h} into common/ and adjust the code
to fit both DS109 and DS414. Moreover:
* Introduce syno_board_id() which translates CONFIG_MACH_TYPE into the
expected board ID tag value.
* Properly initialize isusbhost, mac and mtu fields from env variables.
* Set the right bootargs/bootcmd to correctly boot legacy kernel out of
the (DS414) box. Getting the ramdisk location right is a bit tedious.
Cc: Walter Schweizer <swwa@users.sourceforge.net>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Update hwpartition usage
Check bootbus's arguments
workaround for erratum A-011334 for fsl_esdhc driver
add pulse width detection workaround for fsl_esdhc driver
Use alias num before checking mmc index when creating device
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBr+AgRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebnqQf/dZUk4cpj4q29icFJhAhG3wUkzKdKywWu
wOwHPIaUIetytpjwKTbkv0cUdel5Jhp9mvnJ2O5cRUZlVdgCH+lEQmFiq1O74Jf5
IwYBN74xZuP7+rno3ZxuKhjj2ixbpeg2A5R/o7gaevIgtu4vCK71qrj3y+unjnnt
Rd5BGaVzouMya0lS9cdkrzE1vmuLXs7ZJBvKdppaNda0VScJj+JP3NqooFKRKPU+
OeyblmtfL5lGOXFdY7Wfjg0pzv5L8fJxDaYDxf6iRWWG/X6RO6zV26MWAo28Ga+J
E3fuvl0mBqr1eAg3Cf17j4s9gRZv1tMtS6Mol1scIcBrldalVFA44g==
=x75X
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm
ENOSYS clean-up
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
HS400 mode on the LS1028A SoC isn't reliable. The linux driver has a
workaroung for the pulse width detection. Apply this workaround in
u-boot, too.
This will make HS400 mode work reliably on the LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
We had a problem detecting 8/16bit flash devices connected only via
8bits to the SoC for quite a while. Commit 239cb9d9
[mtd: cfi_flash: Fix CFI flash driver for 8-bit bus support] finally
fixed this 8-bit bus support. But also broke some other boards using
this cfi driver. So this patch had to be reverted.
I spotted a different, simpler approach for this 8-bit bus support
on the barebox mailing list posted by
Oleksij Rempel <bug-track@fisher-privat.net>:
http://www.spinics.net/lists/u-boot-v2/msg14687.html
Here the commit text:
"
Many cfi chips support 16 and 8 bit modes. Most important
difference is use of so called "Q15/A-1" pin. In 16bit mode this
pin is used for data IO. In 8bit mode, it is an address input
which add one more least significant bit (LSB). In this case
we should shift all adresses by one:
For example 0xaa << 1 = 0x154
"
This patch now is a port of this barebox patch to U-Boot.
Along with the change w.r.t from barebox,
Some flash chips can support multiple bus widths, override the
interface width and limit it to the port width.
Tested on 16-bit Spansion flash on sequoia.
Tested 8-bit flashes like 256M29EW, 512M29EW.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Due to a recent change, tests are limited to running on sandbox only.
Correct this so that any architecture can run them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Sean Anderson <seanga2@gmail.com>
Fixes: c79705ea93 ("test: Move dm_test_init() into test-main.c")
Tested-by: Sean Anderson <seanga2@gmail.com>
Avoid 'make htmldocs' build warnings:
./include/os.h:139: warning:
Function parameter or member 'ptr' not described in 'os_realloc'
./include/os.h:139: warning:
Function parameter or member 'length' not described in 'os_realloc'
Fixes: 14e46dfb17 ("sandbox: Add os_realloc()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present debug() statements can cause debuf output to appear when LOG is
enabled but DEBUG is not. This is not intended and it seems that the
condition is wrong.
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently it is not possible to boot Linux from the SD card
by default.
Make the necessary adjustments to allow it.
Reported-by: Peter Bergin <peter@berginkonsult.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrey Zhizhikin <andrey.z@gmail.com> # imx8mn_ddr4_evk
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:
- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Drop a irrelevent comment now the related configs have moved
to the various config files.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is the state as of v5.10 in Linux.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mimicing for example the rk3399, set the SYS_BOOTM_LEN to 64MB so
that regular kernel images can get loaded without problems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SYS_LOAD_ADDR currently is at 0x00280000 which is only 512KB
behind the area where we load u-boot to, which depending on u-boot size
may overlap at some point.
So for safety just pick the same value rk3399 has and set
CONFIG_SYS_LOAD_ADDR to 0x00800800 on rk3368 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When including this file on a board other than sandbox (e.g by enabling
UNIT_TEST and CMD_SETEXPR) an results. Fix it by declaring struct udevice
first.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Some boards may want to show the SKU ID or other information obtained at
runtime. Allow this to come from sysinfo. The board can then provide a
sysinfo driver to provide it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The U_BOOT_CMDREP_COMPLETE() macro produces a build error if CONFIG_CMDLINE
is not enabled. Fix this by updating the macro to provide the 'repeatable'
arugment in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature was dropped from U-Boot some time ago:
f12f96cfaf (sf: Drop spl_flash_get_sw_write_prot")
However, we do need a way to see if a flash device is write-protected,
since if it is, it may not be possible to write to do (i.e. failing to
write is expected).
I am not sure of the correct layer to implement this, so this patch is a
stab at it. If spi-flash makes sense then I will add to the 'sf' also.
Re the points mentioned in the removal commit:
1) This kind of requirement can be achieved using existing
flash operations and flash locking API calls instead of
making a separate flash API.
Which uclass is this?
2) Technically there is no real hardware user for this API to
use in the source tree.
I do want coral (at least) to support this.
3) Having a flash operations API for simple register read bits
also make difficult to extend the flash operations.
This new patch only mentions write-protect being on or off, rather than
the actual mechanism.
4) Instead of touching generic code, it is possible to have
this functionality inside spinor operations in the form of
flash hooks or fixups for associated flash chips.
That sounds to me like what drivers are for. But we still need some sort
of API for it to be accessible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox is special in that it is used for testing and it does not match
any particular target architecture. Allow it to load an image from any
architecture, so that 'bootm' can be used as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when a file is bound to a host device it is always marked as
removeable. Arguably the device is removeable, since it can be unbound at
will. However while it is bound, it is not considered removable by the
user. Also it is useful to be able to model both fixed and removeable
devices for code that distinguishes them.
Add a -r flag to the 'host bind' command and plumb it through to provide
this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow referencing a CBFS file in the flashmap, so that it is possible to
boot from coreboot, where files are not available from binman.
Signed-off-by: Simon Glass <sjg@chromium.org>
CBFS now supports compressed filed. Add support for reading this
information so that the correct decompression can be applied. The
decompression itself is not implemented in CBFS.
Signed-off-by: Simon Glass <sjg@chromium.org>
The file traversal functions currently use a single global CBFS. In some
cases we need to access multiple CBFSs to obtain different files. Add new
functions to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases CBFS does not start with a header but is just a collection
of files. It is possible to support this so long as the size of the CBFS
is provided.
Update the cbfs_init_mem() function to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When U-Boot is booted from coreboot the SMBIOS tables are written by
coreboot, not U-Boot. The existing method of updating the BIOS version
string does not work in that case, since gd->smbios_version is only set
when U-Boot writes the tables.
Add a new function which allows the version to be updated by parsing the
tables and writing the string in the correct place. Since coreboot
provides a pointer to the SMBIOS tables in its sysinfo structure, this
makes it easy to do the update.
Signed-off-by: Simon Glass <sjg@chromium.org>
CBFS now supports attributes for things that cannot fit in the header as
originally conceived. Add the structures for these.
Also rename attributes_offset to something shorter, to ease code
readability.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the eMMC device does not have an alias so it appears after
the SD card which is device 1. There is no device 0 which is odd.
Make the eMMC device be the first one. Update the boot script to use the
new device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
dfu_free_entities() invoking dfu_free_entity_sf() has let to segementation
faults due to double freeing the same device.
spi_flash_free() is not relevant for the driver model but exists only for
compatibility with old drivers.
We must not remove any device here:
* The device may still be referenced.
* We don't want to have to probe again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
driver model support for of-platdata-inst
support of-platdata-inst on x86 / coral
binman support for exapanded entries
binman convert docs to reST
ti-sysc fix for duplicate uclass driver
patman minor improvements
pylibfdt build only if needed
correct obscure CI error with OF_PLATDATA_INST
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBdZYURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreb2rQgAyr1rufrt1UGjZlVjk0HtqX0sdmcOoE4e
6NIuatWXPcP2QR93O9zeGgf/yqNIf3lVIa6Cy3baJBfP6fceZ8B24/xgKKEauPFf
g99sec+q7LPL/oigajXIaWorFXK/NDRtQcSIQFu/EmvCmi0m8Iu0HKFa7YBqa7dc
YdhGnJZZOdYuQmlKewq9q4cIr6qNtTZczsozt4PNZVgB2lKusBNyKRPZErNEFiN6
7A56bb8tcfWgGXenKVTUUcyjWRXM2tt4QtrPFedZsF6cLa8D5v4MfWMs0QBRFl/u
fMzxyeb46x0wsYBNqIBOC7DQWaU/ZeFlr5mQObIH0ypdcsUnEX98sw==
=Ld3P
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26mar21-take2' of git://git.denx.de/u-boot-dm into next
dtoc support for of-platdata-inst
driver model support for of-platdata-inst
support of-platdata-inst on x86 / coral
binman support for exapanded entries
binman convert docs to reST
ti-sysc fix for duplicate uclass driver
patman minor improvements
pylibfdt build only if needed
correct obscure CI error with OF_PLATDATA_INST
Add a warning to each of these functions so that people do not attempt to
use them outside driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Make use of the new priv/plat data region if enabled. This is implemented
as a simple offset from the position set up by dtoc to the new position.
So long as all access goes through dm_priv_to_rw() this is safe.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the device priv/data data allocated by dtoc is stored in the
data section along with other variables. On some platforms it is better
to allocate space for it separately, e.g. if SPL is running from read-only
memory.
Create a new space with the same size as that allocated by dtoc, ready for
use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
