Commit graph

2063 commits

Author SHA1 Message Date
Tom Rini
196311dc72 arm:am33xx: Rework s_init and add board_early_init_f
With the changes to the i2c framework (and adopting the omap24xx_i2c
driver to them) we can no longer call i2c functions prior to gd having
been set and cleared.  When SPL booting, this is handled by setting gd
to point to SRAM in s_init.  However in the cases where we are loaded
directly by ROM (memory mapped NOR or QSPI) we need to make use of the
normal hooks to slightly delay these calls.

Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:14 -04:00
Tom Rini
87acf194a2 arm:am33xx: Make dram_init call sdram_init() in some contexts
We have two contexts for booting these platforms.  One is SPL which is
roughly: reset, cpu_init_crit, lowlevel_init, s_init, sdram_init, _main,
board_init_f from SPL, ... then U-Boot loads.  The other is a
memory-mapped XIP case (NOR or QSPI) where we do not run an SPL.  In
this case we go, roughly: reset, cpu_init_crit, lowlevel_init, s_init,
_main, regular board_init_f.

In the first case s_init will set a valid gd and then be able to call
sdram_init which in many cases will need i2c (which needs a valid gd for
gd->cur_i2c_bus).  In this second case we must (and are able to and
should) defer sdram_init() into dram_init() called by board_init_f as gd
will have been set in _main and cleared in board_init_f.

Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:14 -04:00
Sourav Poddar
7a5f71bc40 am43xx_evm: Add qspiboot target
The ePOS EVM and EVM SK have QSPI as an option to boot.  Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices.  As QSPI is booted from directly we need to chang
CONFIG_SYS_TEXT_BASE.

Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices
we need to handle that elsewhere, once NAND support is also added.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:12 -04:00
pekon gupta
68128e0a86 omap3: remove remnant macros GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT
OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros
to configure GPMC controller for x7 or x8 bit device connected to its interface.
Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above
macros can be completely removed.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:07 -04:00
Tim Harvey
fe0f7f7842 mx6: add mmdc configuration for MX6Q/MX6DL
- add function for configuring iomux based on board-specific regs
- add function for configuring mmdc based on board-specific and
  chip-specific data

Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-06-06 10:07:26 +02:00
Masahiro Yamada
9f2ec3f543 spl: consolidate arch/arm/include/asm/arch-*/spl.h
arch/arm/include/asm/spl.h requires all SoCs to have
arch/arm/include/asm/arch-*/spl.h.

But many of them just define BOOT_DEVICE_* macros.

Those macros are used in the "switch (boot_device) { ... }"
statement in common/spl/spl.c.

So they should not be archtecture specific, but be described as
a simpile enumeration.

This commit merges most of arch/arm/include/asm/arch-*/spl.h
into arch/arm/include/asm/spl.h.

With a little more effort, arch-zynq/spl.h and arch-socfpga/spl.h
will be merged, while I am not sure about OMAP and Exynos.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bo Shen <voice.shen@atmel.com> [on sama5d3xek board for at91 part]
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stefano Babic <sbabic@denx.de> [applying Tim's i.MX6 patches]
Acked-by: Tom Rini <trini@ti.com>
2014-06-06 10:05:34 +02:00
Albert ARIBAUD
cc49da249c Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-06-02 08:43:48 +02:00
Doug Anderson
567802bbd6 Exynos: Make sure ps_hold gets set in the SPL
Setting ps_hold ought to be one of the first things we do when we
first boot up. If we wait until the main u-boot runs we won't set it
in time and the PMIC may power us back off.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-31 14:22:20 +09:00
Tom Rini
90b51c33f3 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-05-30 11:34:39 -04:00
Simon Glass
ae4223f444 Remove unnecessary use of hush header file
Some files include hush.h but don't actually use it. Remove this where
possible.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-05-29 17:45:31 -04:00
Simon Glass
eb0dd9986c exynos: Enable PSHOLD in SPL
There is quite a tight deadline in enabling PSHOLD, less than a second.
In some cases (e.g. with USB download), U-Boot takes longer than that
to load, so the board powers off before U-Boot starts.

Add a call in SPL to enable PSHOLD.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-28 10:58:19 +09:00
Wu, Josh
cf874c190e ARM: at91sam9m10g45ek: enable mci0 support
Also we enable the mmc command in configuration file.

As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
so remove the redundant CONFIG_DOS_PARTITION definition.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-05-27 00:10:54 +02:00
Andreas Bießmann
5c390a5b26 arm:at91: enable ROM loadable atmel image
For sama5d3xek we need to modify the SPL image for correct detection by ROM
code.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
2014-05-27 00:10:49 +02:00
Bo Shen
12bbc0ba81 ARM: atmel: switch to main crystal osc for SPL boot
If without switch to main crystal oscillator, the sama5d3 SoC will
use internal on chip RC oscillator.
In order to get better accuracy, switch to main crystal oscillator.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-05-27 00:10:40 +02:00
Ian Campbell
50827a5991 sunxi: non-FEL SPL boot support for sun7i
Add support for booting from an MMC card.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:31:03 +02:00
Ian Campbell
5835823da3 sunxi: add gmac Ethernet support
Add support for the GMAC Ethernet controller on Allwinner A20 (sun7i)
processors. Enable for the Cubietruck.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:25:12 +02:00
Ian Campbell
cba69eeeaa sunxi: add sun7i cpu, board and start of day support
This patch adds generic board, start of day and basic build system support for
the Allwinner A20 (sun7i) processor. This code will not been compiled until the
build is hooked up in a later patch. It has been split out to keep the patches
manageable.

Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Patrick Wood <patrickhwood@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:12:40 +02:00
Ian Campbell
286c3c3a5e sunxi: add sun7i dram setup support
This patch adds DRAM initialisation support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:12:30 +02:00
Ian Campbell
fe1b4db05e sunxi: add sun7i pinmux and gpio support
This patch adds the basic pinmux and gpio support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:12:21 +02:00
Ian Campbell
643cf0ea02 sunxi: add sun7i clocks and timer support.
This patch adds the basic clocks and timer support for the Allwinner A20
(sun7i) processor. This code will not been compiled until the build is hooked
up in a later patch. It has been split out to keep the patches manageable.

Some of the code here is common to multiple sunxi subarchtectures, hence files
are named sun4i which is the earliest similar variant.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:12:12 +02:00
David Feng
1277bac0d2 Arm64 fix a bug of vbar_el3 initialization
Signed-off-by: David Feng <fenghua@phytium.com.cn>
2014-05-25 15:26:00 +02:00
Albert ARIBAUD
33144ea443 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-05-24 09:50:00 +02:00
Sergey Alyoshin
21254713d3 am33xx: report silicon revision instead of code
As revision code 1 is for silicon revision 2.0, it is easily confused with
silicon revision 1.0.

Device type report also reworked in same style.

Signed-off-by: Sergey Alyoshin <alyoshin.s@gmail.com>
2014-05-23 19:40:39 -04:00
Lokesh Vutla
d7630da6f4 ARM: OMAP: Fix omap_sdram_size calculation
Last section of DMM is used for trapping tiler unmapped sections.
Corresponding trap_size should be deducted from total SDRAM size
only if trap section is overlapping with available SDRAM
based on DMM sections. Fixing the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-05-23 19:40:38 -04:00
Tom Rini
939911a64b armv7:TI: Add <asm/ti-common/sys_proto.h> and migrate omap_hw_init_context
The omap_hw_init_context function (and assorted helpers) is the same for
all OMAP-derived parts as when CHSETTINGS are used, that's the same and
our DDR base is also always the same.  In order to make this common we
simply need to update the names of the define for DDR address space
which is also common.

Cc: Sricharan R. <r.sricharan@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-05-23 19:40:05 -04:00
Lokesh Vutla
02847fcc92 ARM: DRA7xx: ctrl: Fix efuse register addresses
Efuse register addresses are wrongly programmed.
Fixing the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-05-23 19:40:04 -04:00
Lokesh Vutla
9fcf3d3a1d ARM: DRA72x: Update EMIF data
DRA72 has 1GB connected to EMIF1 only. Updating the details.
And also enable WA for BUG0039 only if corresponding EMIF is present.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-05-23 19:40:04 -04:00
Lokesh Vutla
4d6bf5542e ARM: DRA72x: clocks: Update the hwdata
Adding the prcm, dplls, control module hooks for DRA72x.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-05-23 19:40:04 -04:00
Keerthy
8b0d1bbc7e ARM: DRA72x: volt: Update the pmic offsets
TPS65917 is used in DRA722 evm. Update the address offsets accordingly.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-05-23 19:40:04 -04:00
Lokesh Vutla
ee77a2389b ARM: DRA72x: Add Silicon ID support
Add silicon ID code for DRA722 silicon.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-05-23 19:40:04 -04:00
pekon gupta
a0a37183bd ARM: omap: merge GPMC initialization code for all platform
GPMC controller on TI's OMAP SoC is general purpose controller to interface
with different types of external devices like;
 - parallel NOR flash
 - parallel NAND flash
 - OneNand flash
 - SDR RAM
 - Ethernet Devices like LAN9220

Though GPMC configurations may be different for each platform depending on
clock-frequency and external device interfacing with controller. But
initialization sequence remains common across all platfoms.

Thus this patch merges gpmc_init() scattered in different arch-xx/mem.c
files into single omap-common/mem-common.c

However, actual platforms specific register config values are still sourced
from corresponding platform specific headers like;
 AM33xx: arch/arm/include/asm/arch-am33xx/mem.h
 OMAP3:  arch/arm/include/asm/arch-omap3/mem.h
 OMAP4:  arch/arm/include/asm/arch-omap4/mem.h
 OMAP4:  arch/arm/include/asm/arch-omap5/mem.h

Also, CONFIG_xx passed by board-profile decide config for which set of macros
need to be used for initialization
 CONFIG_NAND:    initialize GPMC for NAND device
 CONFIG_NOR:     initialize GPMC for NOR device
 CONFIG_ONENAND: initialize GPMC for ONENAND device

Signed-off-by: Pekon Gupta <pekon@ti.com>
[trini: define GPMC_SIZE_256M for omap3]
Signed-off-by: Tom Rini <trini@ti.com>
2014-05-23 19:39:36 -04:00
Albert ARIBAUD
3eb5e19863 Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master' 2014-05-23 22:50:43 +02:00
Albert ARIBAUD
c534d2fdcf Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master' 2014-05-23 22:50:23 +02:00
Nobuhiro Iwamatsu
dd73018b16 arm: rmobile: r8a7791: Fix MOD_SEL3 function table about FN_SEL_IEB
FN_SEL_IEB is assigned 2bit, and 2bit can represent 4 patterns.
However FN_SEL_IEB but we only use 3. It adds empty patterns as 0.

Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Albert ARIBAUD
a26acb7dc9 Merge remote-tracking branch 'u-boot-sh/rmobile'
Conflicts:
	boards.cfg

Trivial conflict, maintainer change plus board addition
2014-05-16 20:43:04 +02:00
Jaehoon Chung
39c4975622 ARM: exynos: clock: modify the set_mmc_clk for exynos4
Modified the mmc_set_clock for eynos4.
The goal of this patch is that fsys-div register should be reset.
And retore the div-value, not using the value of lowlevel_init.
(For using SDMMC4, this patch is needs)

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Beomho Seo
00ee81300f arm: exynos: clock: Remove exynos4x12_set_mmc_clk function
exynos4x12_set_mmc_clk function have been removed.
Because, exynos4x12_clock and exynos4_clock return same div_fsys* value.

Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Beomho Seo
77ee62d882 arm: exynos: pinmux: add sdmmc4 gpio configratuion
For use dwmmc controller at exynos4, add SDMMC4 gpio configuration.

Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Albert ARIBAUD
44cfc3a83f Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master' 2014-05-15 17:19:45 +02:00
Albert ARIBAUD
9f5f51540d Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-05-15 16:36:02 +02:00
Albert ARIBAUD
41623c91b0 arm: move exception handling out of start.S files
Exception handling is basically identical for all ARM targets.
Factorize it out of the various start.S files and into a
single vectors.S file, and adjust linker scripts accordingly.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-05-15 16:24:53 +02:00
Albert ARIBAUD
60a4f39fcd arm: remove unused _end_vect and _vectors_end symbols
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-05-15 16:24:47 +02:00
Albert ARIBAUD
23ff29bc17 arm: pxa: move SP check from start.S to cpuinfo.c
PXA start.S has a PXA (variant) specific check in
start.S. Move it to cpuinfo.c.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marex@denx.de>
2014-05-15 16:24:41 +02:00
Albert ARIBAUD
cd6cc3440f arm: move reset_cpu from start.S into cpu.c
CPUs arm946es and sa1100 both define the reset_cpu()
function in their start.S file. Move this cpu-specific code
into cpu.c so that start.S only contains ARM generic code.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-05-15 16:24:37 +02:00
Albert ARIBAUD
b4ee1491b9 arm1136: move cache code from start.S to cache.c
arch/arm/cpu/arm1136/start.S contain a cache flushing function.
Remove the function and move its code into arch/arm/lib/cache.c.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-05-15 16:24:26 +02:00
Masahiro Yamada
66e6715c5f zynq: treat ps7_init.c/h as external files to ignore them
ps7_init.c and ps7_init.h are supposed to be exported by hw project
and copied to board/xilinx/zynq/ directory.

We want them to be ignored by git.
So what we should do is to always treat them as external files
rather than replacing ps7_init.c

This commit does:

 - Move a weak function ps7_init() to arch/arm/cpu/armv7/zynq/spl.c
   and delete board/xilinx/zynq/ps7_init.c

 - Compile board/xilinx/zynq/ps7_init.c only when it exists

 - Add .gitignore to ignore ps7_init.c/h

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:52:46 +02:00
Michal Simek
eb8c54bfaa ARM: zynq: ehci: Added USB host driver support
Added USB host driver for zynq.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:35 +02:00
Michal Simek
3cc3fa8672 ARM: zynq: Add MIO detection code
Add run-time MIO pin detection to get actual
pin configuration for specific periphery.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:35 +02:00
Michal Simek
2da7a745b6 ARM: zynq: Setup correct slcr_lock value
The driver should setup slcr state according
to slcr operations.

Reported-by: Andrey Filippov <andrey@elphel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:34 +02:00
Michal Simek
6e04769caf ARM: zynq: slcr: Fix incorrect commentary
Fix c&p error in zynq_slcr_devcfg_enable() commentary
and extending it with description according
to Zynq TRM also in zynq_slcr_devcfg_disable().

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:34 +02:00
Michal Simek
1540fb725b ARM: zynq: Call zynq board_init() in SPL
Call board_init() if SPL is configured with CONFIG_SPL_BOARD_INIT.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2014-05-14 07:43:34 +02:00
Michal Simek
10fa49f428 ARM: zynq: Do not use half memory size for ECC case
Memory size should be specified without ECC place.
If you need to have half memory size, please change
u-boot configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:34 +02:00
Siva Durga Prasad Paladugu
96a2859e54 ARM: zynq: Added efuse status register base address
Added efuse status register base address. This register
is used for determining whether efuse was blown or not.
Also, added the zynq_get_silicon_version() to get the
silicon version of the zynq board.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:34 +02:00
Michal Simek
ec9638659f ARM: zynq: Fix sparse warning in ddrc.c
Warning:
arch/arm/cpu/armv7/zynq/ddrc.c:43:24: warning: Using plain integer as NULL pointer

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:34 +02:00
Michal Simek
3b5b599f17 ARM: zynq: Fix sparse warnings in slcr.c
Warnings:
arch/arm/cpu/armv7/zynq/slcr.c:21:6: warning: symbol 'zynq_slcr_lock' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:27:6: warning: symbol 'zynq_slcr_unlock' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:34:6: warning: symbol 'zynq_slcr_cpu_reset' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:54:6: warning: symbol 'zynq_slcr_gem_clk_setup' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:81:6: warning: symbol 'zynq_slcr_devcfg_disable' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:94:6: warning: symbol 'zynq_slcr_devcfg_enable' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:107:5: warning: symbol 'zynq_slcr_get_boot_mode' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:113:5: warning: symbol 'zynq_slcr_get_idcode' was not declared. Should it be static?

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:33 +02:00
Stephen Warren
2364e151e4 ARM: tegra: use a CPU freq that all SKUs can support
U-Boot on Tegra30 currently selects a main CPU frequency that cannot be
supported at all on some SKUs, and needs higher VDD_CPU/VDD_CORE values
on some others. This can result in unreliable operation of the main CPUs.

Resolve this by switching to a CPU frequency that can be supported by any
SKU. According to the following link, the maximum supported CPU frequency
of the slowest Tegra30 SKU is 600MHz:

repo http://nv-tegra.nvidia.com/gitweb/?p=linux-2.6.git;a=summary
branch l4t/l4t-r16-r2
path arch/arm/mach-tegra/tegra3_dvfs.c
table cpu_dvfs_table[]

According to that same table, the minimum VDD_CPU required to operate at
that frequency across all SKUs is 1.007V. Given the adjustment resolution
of the TPS65911 PMIC that's used on all Tegra30-based boards we support,
we'll end up using 1.0125V instead.

At that VDD_CPU, tegra3_get_core_floor_mv() in that same file dictates
that VDD_CORE must be at least 1.2V on all SKUs. According to
tegra_core_speedo_mv() (in tegra3_speedo.c in the same source tree),
that voltage is safe for all SKUs.

An alternative would be to port much of the code from tegra3_dvfs.c and
tegra3_speedo.c in the kernel tree mentioned above. That's more work
than I want to take on right now.

While all the currently supported boards use the same regulator chip for
VDD_CPU, different types of regulators are used for VDD_CORE. Hence, we
add some small conditional code to select how VDD_CORE is programmed. If
this becomes more complex in the future as new boards are added, or we
end up adding code to detect the SoC SKU and dynamically determine the
allowed frequency and required voltages, we should probably make this a
runtime call into a function provided by the board file and/or relevant
PMIC driver.

Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Bard Liao <bardliao@realtek.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:32 -07:00
Stephen Warren
bb14469ae0 ARM: tegra: add function to enable input clamping on tristate
The HW-defined procedure for booting Tegra requires that
CLAMP_INPUTS_WHEN_TRISTATED be enabled before programming the pinmux.
Add a function to the pinmux driver to allow boards to do this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:31 -07:00
Stephen Warren
4a68d3431a ARM: tegra: allow pinmux mux option not to be set by init tables
Define enum PMUX_FUNC_DEFAULT, which indicates that a table entry passed
to pinmux_config_pingrp()/pinmux_config_pingrp_table() shouldn't change
the mux option in HW.

For pins that will be used as GPIOs, the mux option is irrelevant, so we
simply don't want to define any mux option in the pinmux initialization
table.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:31 -07:00
Stephen Warren
48ec7a9468 ARM: tegra: fix CPU VDD comment in Tegra30 CPU init code
The register writes performed by arch/arm/cpu/arm720t/tegra30/cpu.c
enable_cpu_power_rail() set the voltage to 1.0V not 1.4V as the comment
implies. Fix the comment.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:31 -07:00
Akshay Saraswat
f6ae1ca058 S5P: Exynos: Add GPIO pin numbering and rename definitions
This patch includes following changes :
* Adds gpio pin numbering support for EXYNOS SOCs.
  To have consistent 0..n-1 GPIO numbering the banks are divided
  into different parts where ever they have holes in them.

* Rename GPIO definitions from GPIO_... to S5P_GPIO_...
  These changes were done to enable cmd_gpio for EXYNOS and
  cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence
  getting a error during compilation.

* Adds support for name to gpio conversion in s5p_gpio to enable
  gpio command EXYNOS SoCs. Function has been added to asm/gpio.h
  to decode the input gpio name to gpio number.
  Example: SMDK5420 # gpio set gpa00

Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-13 15:20:38 +09:00
Albert ARIBAUD
d2a3e91139 Merge branch 'u-boot/master'
Conflicts:
	drivers/net/Makefile

(trivial merge)
2014-05-09 11:50:14 +02:00
Nobuhiro Iwamatsu
73ff6801e6 arm: rmobile: Update print_cpuinfo function
The print_cpuinfo fucntion has same code.
It has a code of many common.  This adds a table of CPU information, duplicate
using for-loop.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-28 04:35:12 +09:00
Nobuhiro Iwamatsu
a028abea6c arm: rmobile: Add rmobile_get_cpu_rev_fraction() for R-Car SoCs
This adds rmobile_get_cpu_rev_fraction to get fraction revision for R-Car SoCs.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-28 04:35:12 +09:00
Nobuhiro Iwamatsu
210f7b2d26 arm: rmobile: Add 1 to value of the CPU revision in rmobile_get_cpu_rev_integer()
Value that can be obtained in the rmobile_get_cpu_rev_integer() starts at 0.
However, revisions to start from 1, which adds 1.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-28 04:35:12 +09:00
Nobuhiro Iwamatsu
9b7fa2fed6 arm: rmobile: Merge functions to get the CPU information of R8A7790 and R8A7791
Functions to get the CPU information of R8A7790 and R8A7791 are common.
This merges these as cpu_info-rcar.c.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-28 04:35:12 +09:00
Nobuhiro Iwamatsu
42c53ab0a7 arm: rmobile: r8a779x: Fix L2 cache init and latency setting
L2CTLR only need to update for cluster 0.
This changes L2CTLR to initialize only when cluster is 0.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-28 04:35:11 +09:00
Albert ARIBAUD
c9aab0f9dd Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-04-21 21:01:35 +02:00
Tom Rini
b149c4c399 ARM:tegra20: Remove aes debug prints
In 6e7b9f4 some of the debug prints for AES code moved into the generic
code, so we remove these additional calls.

Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Tom Warren <twarren@nvidia.com>
2014-04-18 16:14:17 -04:00
Stephen Warren
53eb768dfb aes: make apply_cbc_chain_data non-static
Tegra's crypto.c uses apply_cbc_chain_data() to sign the warm restart
code. This function was recently moved into the core aes.c and made
static, which prevents the Tegra code from compiling. Make it public
again to avoid the compile errors:

arch/arm/cpu/tegra20-common/crypto.c: In function ‘sign_object’:
arch/arm/cpu/tegra20-common/crypto.c:74:3: warning: implicit declaration of function ‘apply_cbc_chain_data’ [-Wimplicit-function-declaration]
arch/arm/cpu/built-in.o: In function `sign_object':
.../arch/arm/cpu/tegra20-common/crypto.c:74: undefined reference to `apply_cbc_chain_data'
.../arch/arm/cpu/tegra20-common/crypto.c:78: undefined reference to `apply_cbc_chain_data'

Fixes: 6e7b9f4fa0 ("aes: Move the AES-128-CBC encryption function to common code")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
2014-04-18 16:14:17 -04:00
Masahiro Yamada
d8d7cbd96a kbuild: use boolean macros to select tegra*-common directory
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-17 17:44:35 -04:00
Manish Badarkhe
893b92f86f arm, da850: staticize funtions
Make funtions static which are locally used in file
and remove the declaration from header file.

Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
2014-04-17 17:24:40 -04:00
Tom Rini
d0e6d34d7c am335x: Switch to CONFIG_SKIP_LOWLEVEL_INIT from guarding SPL or NOR_BOOT
In the case of SPL or NOR_BOOT (no SPL involved) we need to include
certain code in the build.  Use !CONFIG_SKIP_LOWLEVEL_INIT rather than
CONFIG_SPL_BUILD || CONFIG_NOR_BOOT to make the code clearer, and to
make supporting XIP QSPI boot clearer in the code.

Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
2014-04-17 17:24:40 -04:00
Vitaly Andrianov
30fe8c150f keystone2: add keystone multicore navigator driver
Multicore navigator consists of Network Coprocessor (NetCP) and
Queue Manager sub system. More details on the hardware can
be obtained from the following links:-

Network Coprocessor: http://www.ti.com/lit/pdf/sprugz6
Multicore Navigator: http://www.ti.com/lit/pdf/sprugr9

Multicore navigator driver implements APIs to configure
the Queue Manager and NetCP Pkt DMA.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:39 -04:00
Vitaly Andrianov
ef509b9063 k2hk: add support for k2hk SOC and EVM
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.

This patch add support for keystone architecture and k2hk evm.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
2014-04-17 17:24:38 -04:00
Vitaly Andrianov
e8459dcc33 i2c, davinci: convert driver to new mutlibus/mutliadapter framework
- add davinci driver to new multibus/multiadpater support
    - adapted all config files, which uses this driver

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-04-17 17:24:38 -04:00
Vitaly Andrianov
11bc755722 arm: add support for arch timer
This patch add basic support for the architecture timer found on recent
ARMv7 based SoCs.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
2014-04-17 17:24:38 -04:00
Tom Rini
79b079f35c dra7xx_evm: Add QSPI_4 support, qspiboot build target
We previously only supported QSPI_1 (single) support.  Add QSPI_4 (quad)
read support as well.  This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value.  We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment.  When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:37 -04:00
Nishanth Menon
79e7e87f91 omap3/sys_info: provide interface to read die id
introduce get_die_id() function which allows generation of
information such as fake MAC address from the processor ID code.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 14:39:54 -04:00
Nishanth Menon
8a0c6d6fa9 OMAP: common: consolidate fake USB ethernet MAC address creation
TI platforms such as OMAP5uevm, PandaBoard, use equivalent
logic to generate fake USB MAC address from device unique DIE ID.

Consolidate this to a generic location such that other TI platforms such
as BeagleBoard-XM can also use the same.

NOTE: at this point in time, I dont yet see a need for a generic dummy
ethernet MAC address creation function, but if there is a need in the
future, this can be further abstracted out.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 14:39:54 -04:00
Wolfgang Denk
a88e55c4c6 ARM: OMAP: replace custom sr32() by standard I/O accessors
Replace the custom bit manipulation function sr32() by standard I/O
accessors.  A major motivation for this cleanup was the fact, that a
number of calls of that function resulted in 32 bit wide shift
operations on u32 data, which according to the C-ISO/IEC-9899-Standard
provokes undefined behaviour:

	6.5.7 Bitwise shift operators
	...
        If the value of the right operand is negative or is greater
        than or equal to the width of the promoted left operand, the
        behavior is undefined.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-04-17 14:39:54 -04:00
Wolfgang Denk
4e4685027c ARM: OMAP: hide custom bit manipulation function sr32()
The only remaining user of the custom bit manipulation function sr32()
is arch/arm/cpu/armv7/omap3/clock.c, so  make it a static function in
that file to prepare complete removal.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-04-17 14:39:54 -04:00
Wolfgang Denk
e7300f463d ARM: OMAP: remove sr32() from OMAP board code
Replace the custom sr32() bit manipulation function in
arch/arm/cpu/armv7/omap3/board.c and board/ti/panda/panda.c
by standard I/O accessors.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-04-17 14:39:54 -04:00
Tom Rini
0f507779ca Merge branch 'next' 2014-04-17 14:33:25 -04:00
Stephen Warren
d381294aef ARM: tegra: pack pinmux data tables tighter
Use smaller fields in the Tegra pinmux structures in order to pack the
data tables into a smaller space. This saves around 1-3KB for the SPL
and around 3-8KB for the main build of U-Boot, depending on the board,
which SoC it uses, and how many pinmux table entries there are.

In order to pack PMUX_FUNC_* into a smaller space, don't hard-code the
values of PMUX_FUNC_RSVD* to values which require 16 bits to store them,
but instead let their values be assigned automatically, so they end up
fitting into 8 bits.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00
Stephen Warren
d68c942927 ARM: tegra: Tegra124 pinmux cleanup
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.

The entries in tegra124_pingroups[] are all updated to remove the columns
which are no longer used.

All affected code is updated to match.

There are differences in the set of drive groups. I have validated this
against the TRM. There are differences order of pin definitions in
pinmux.c; these previously had significant mismatches with the correct
order:-( I adjusted a few entries in pinmux-config-venice2.h since the
set of legal functions for some pins was updated to match the TRM.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00
Stephen Warren
1fa3a63413 ARM: tegra: Tegra114 pinmux cleanup
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.

The entries in tegra114_pingroups[] are all updated to remove the columns
which are no longer used.

All affected code is updated to match.

This introduces a few changes to pin/group/function naming and the set of
available functions for each pin. The new values now exactly match the
TRM; the chip documentation. I adjusted a few entries in
pinmux-config-dalmore.h due to this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00
Stephen Warren
803d01edc2 ARM: tegra: Tegra30 pinmux cleanup
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.

The entries in tegra30_pingroups[] are all updated to remove the columns
which are no longer used.

All affected code is updated to match.

This introduces a few changes to pin/group/function naming and the set of
available functions for each pin. The new values now exactly match the
TRM; the chip documentation. I adjusted one entry in
pinmux-config-cardhu.h due to this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
70ad375ee4 ARM: tegra: Tegra20 pinmux cleanup
This renames all the Tegra20 pinmux pins and functions so they have a
prefix which matches the type name.

The entries in tegra20_pingroups[] are all updated to remove the columns
which are no longer used.

All affected code is updated to match.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
dfb42fc95d ARM: tegra: pinmux naming consistency fixes
Clean up the naming of pinmux-related objects:
* Refer to drive groups rather than pad groups to match the Linux kernel.
* Ensure all pinmux API types are prefixed with pmux_, values (defines)
  are prefixed with PMUX_, and functions prefixed with pinmux_.
* Modify a few type names to make their content clearer.
* Minimal changes to SoC-specific .h/.c files are made so the code still
  compiles. A separate per-SoC change will be made immediately following,
  in order to keep individual patch size down.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
a45fa43685 ARM: tegra: reduce public pinmux API
Remove a few unused functions from the pinmux header. They aren't
currently used, and removing them prevents any new usage from appearing.
This will ease moving to just pinmux_config_table() and
padgrp_config_table() in the future.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
e296995767 ARM: tegra: pinctrl: remove duplication
Much of arch/arm/cpu/tegra*-common/pinmux.c is identical. Remove the
duplication by creating pinmux-common.c for all the identical code.

This leaves:
* arch/arm/include/asm/arch-tegra*/pinmux.h defining only the names of
  the various pins/pin groups, drive groups, and mux functions.
* arch/arm/cpu/tegra*-common/pinmux.c containing only the lookup table
  stating which pin groups support which mux functions.

The code in pinmux-common.c is semantically identical to that in the
various original pinmux.c, but had some consistency and cleanup fixes
applied during migration.

I removed the definition of struct pmux_tri_ctlr, since this is different
between SoCs (especially Tegra20 vs all others), and it's much simpler to
deal with this via the new REG/MUX_REG/... defines. spl.c, warmboot.c,
and warmboot_avp.c needed updates due to this, since they previously
hijacked this struct to encode the location of some non-pinmux registers.
Now, that code simply calculates these register addresses directly using
simple and obvious math. I like this method better irrespective of the
pinmux code cleanup anyway.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
19ed7b4ecf ARM: tegra: use apb_misc.h in more places
Tegra's "APB misc" register region contains various miscellaneous
registers and the Tegra pinmux registers. Some code that touches the
misc registers currently uses struct pmux_tri_ctlr, which is intended to
be a definition of pinmux registers, rather than struct apb_misc_pp_ctrl,
which is intended to be a definition of the miscellaneous registers.
Convert all such code to use struct apb_misc_pp_ctrl, since struct
pmux_tri_ctlr goes away in the next patch.

This requires adding a missing field definition to struct
apb_misc_pp_ctrl, and moving the header into a more common location.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
6ac1e542c6 ARM: tegra: pinctrl: make pmux_func values consistent on Tegra20
For consistency with other SoCs, modify Tegra20's enum pmux_func to:

* Remove PMUX_FUNC values that aren't real
* Use the same PMUX_FUNC_RSVD[1-4] values, and ensure (RSVD1 & 3)==0;
  this will be assumed by pinmux_set_func() in a future patch.

Unfortunately, PMUX_FUNC_RSVD is still used in the pin macros. Use a
private define inside the driver to prevent this from causing compilaton
errors. This will be cleaned up when the pin tables are re-written in a
later patch in this series.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
dd45948dd7 ARM: tegra: pinctrl: remove vddio
This field isn't used anywhere, so remove it. Note that PIN() macros are
left unchanged for now, to avoid many diffs to them; later commits will
completely rewrite them just one time.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:05 -07:00
Stephen Warren
0d2c0d5788 ARM: tegra: pinctrl: remove func_safe
This field isn't used anywhere, so remove it. Note that PIN() macros are
left unchanged for now, to avoid many diffs to them; later commits will
completely rewrite them just one time.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:04 -07:00
Albert ARIBAUD
519fdde9e6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	include/configs/trats.h
	include/configs/trats2.h
	include/mmc.h
2014-04-08 09:25:08 +02:00
David Feng
c71645ad2b arm64 patch: gicv3 support
This patch add gicv3 support to uboot armv8 platform.

Changes for v2:
  - rename arm/cpu/armv8/gic.S with arm/lib/gic_64.S
  - move smp_kick_all_cpus() from gic.S to start.S, it would be
    implementation dependent.
  - Each core initialize it's own ReDistributor instead of master
    initializeing all ReDistributors. This is advised by arnab.basu
    <arnab.basu@freescale.com>.

Signed-off-by: David Feng <fenghua@phytium.com.cn>
2014-04-08 00:15:12 +02:00
Leo Yan
42ddfad6ab ARMv8: fix bug for flush data cache by set/way
When flush the d$ with set/way instruction, it need calculate the way's
offset = log2(Associativity); but in current uboot's code, it use below
formula to calculate the offset: log2(Associativity * 2 - 1), so finally
it cannot flush data cache properly.

Signed-off-by: Leo Yan <leoy@marvell.com>
2014-04-07 22:27:22 +02:00
Albert ARIBAUD
284bb60ed6 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-04-07 19:13:42 +02:00
Nitin Garg
b7588e3bdc ARM: Add workaround for Cortex-A9 errata 761320
Full cache line writes to the same memory region from at least two
processors might deadlock the processor. Exists on r1, r2, r3
revisions.

Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-04-07 18:11:01 +02:00
Nitin Garg
f71cbfe3ca ARM: Add workaround for Cortex-A9 errata 794072
A short loop including a DMB instruction might cause a denial of
service on another processor which executes a CP15 broadcast operation.
Exists on r1, r2, r3, r4 revisions.

Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2014-04-07 18:11:00 +02:00
York Sun
1e6ad55c05 armv8/cache: Change cache invalidate and flush function
When SoC first boots up, we should invalidate the cache but not flush it.
We can use the same function for invalid and flush mostly, with a wrapper.

Invalidating large cache can ben slow on emulator, so we postpone doing
so until I-cache is enabled, and before enabling D-cache.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
2014-04-07 17:43:41 +02:00
York Sun
83571bcab1 armv8/cache: Flush D-cache, invalidate I-cache for relocation
If D-cache is enabled, we need to flush it, and invalidate i-cache before
jumping to the new location. This should be done right after relocation.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
2014-04-07 17:43:36 +02:00
York Sun
f5222cfd49 armv8/cache: Consolidate setting for MAIR and TCR
Move setting for MAIR and TCR to cache_v8.c, to avoid conflict with
sub-architecture.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
2014-04-07 17:43:32 +02:00
Andreas Färber
2c67e0e7cf arm: Handle .gnu.hash section in ldscripts
Avoids "could not find output section .gnu.hash" ld.bfd errors on openSUSE.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2014-04-07 11:12:18 +02:00
Chin Liang See
ddfeb0aaf4 socfpga: Adding Clock Manager driver
Clock Manager driver will be called to reconfigure all the
clocks setting based on user input. The input are passed to
Preloader through handoff files

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
2014-04-07 10:41:50 +02:00
Marek Vasut
1a9df13d5b arm: mxs: Add support for generating signed BootStream
This patch adds the groundwork for generating signed BootStream, which
can be used by the HAB library in i.MX28. We are adding a new target,
u-boot-signed.sb , since the process for generating regular non-signed
BootStream is much easier. Moreover, the signed bootstream depends on
external _proprietary_ _binary-only_ tool from Freescale called 'cst',
which is available only under NDA.

To make things even uglier, the CST or HAB mandates a kind-of circular
dependency. The problem is, unlike the regular IVT, which is generated
by mxsimage, the IVT for signed boot must be generated by hand here due
to special demands of the CST. The U-Boot binary (or SPL binary) and IVT
are then signed by the CST as a one block. But here is the problem. The
size of the entire image (U-Boot, IVT, CST blocks) must be appended at
the end of IVT. But the size of the entire image is not known until the
CST has finished signing the U-Boot and IVT. We solve this by expecting
the CST block to be always 3904B (which it is in case two files, U-Boot
and the hand-made IVT, are signed in the CST block).

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-04-04 11:44:59 +02:00
Stefano Babic
1cad23c5f4 Merge branch 'master' of git://git.denx.de/u-boot-arm into master
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/mxsimage.mx23.cfg
	arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-04-04 11:35:30 +02:00
Stefano Babic
5dd73bc0a4 Revert "arm: mxs: Add support for generating signed BootStream"
This reverts commit 53e6b14e03.

Patch does not merge anymore with u-boot-arm and must be rebased.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-04-04 11:29:29 +02:00
Stefano Babic
bb2637be09 mxs: fix warning in SPL with console support
Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-04-02 10:42:06 +02:00
Marek Vasut
9926eb31b7 arm: mxs: Add serial console support into SPL
Add support for serial console into the i.MX23/i.MX28 SPL. A full,
uncrippled serial console support comes very helpful when debugging
various spectacular hardware bringup issues early in the process.
Because we do not use SPL framework, but have our own minimalistic
SPL, which is compatible with the i.MX23/i.MX28 BootROM, we do not
use preloader_console_init(), but instead use a similar function to
start the console. Nonetheless, to avoid blowing up the size of the
SPL binary, this support is enabled only if CONFIG_SPL_SERIAL_SUPPORT
is defined, which is disabled by default.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-04-01 10:25:11 +02:00
Marek Vasut
65ed5e8572 arm: mxs: Properly set GD pointer in SPL
Set the GD pointer in the SPL to a defined symbol so various
functions from U-Boot can be used without adverse side effects.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-04-01 10:23:01 +02:00
Marek Vasut
53e6b14e03 arm: mxs: Add support for generating signed BootStream
This patch adds the groundwork for generating signed BootStream, which
can be used by the HAB library in i.MX28. We are adding a new target,
u-boot-signed.sb , since the process for generating regular non-signed
BootStream is much easier. Moreover, the signed bootstream depends on
external _proprietary_ _binary-only_ tool from Freescale called 'cst',
which is available only under NDA.

To make things even uglier, the CST or HAB mandates a kind-of circular
dependency. The problem is, unlike the regular IVT, which is generated
by mxsimage, the IVT for signed boot must be generated by hand here due
to special demands of the CST. The U-Boot binary (or SPL binary) and IVT
are then signed by the CST as a one block. But here is the problem. The
size of the entire image (U-Boot, IVT, CST blocks) must be appended at
the end of IVT. But the size of the entire image is not known until the
CST has finished signing the U-Boot and IVT. We solve this by expecting
the CST block to be always 3904B (which it is in case two files, U-Boot
and the hand-made IVT, are signed in the CST block).

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-03-31 18:28:50 +02:00
Marek Vasut
9c2c8a3129 arm: mxs: Adjust the load address of U-Boot and SPL for HAB
When using HAB, there are additional special requirements on the placement of
U-Boot and the U-Boot SPL in memory. To fullfill these, this patch moves the
U-Boot binary a little further from the begining of the DRAM, so the HAB CST
and IVT can be placed in front of the U-Boot binary. This is necessary, since
both the U-Boot and the IVT must be contained in single CST signature. To
make things worse, the IVT must be concatenated with one more entry at it's
end, that is the length of the entire CST signature, IVT and U-Boot binary
in memory. By placing the blocks in this order -- CST, IVT, U-Boot, we can
easily align them all and then produce the length field as needed.

As for the SPL, on i.MX23/i.MX28, the SPL size is limited to 32 KiB, thus
we place the IVT at 0x8000 offset, CST right past IVT and claim the size
is correct. The HAB library accepts this setup.

Finally, to make sure the vectoring in SPL still works even after moving
the SPL from 0x0 to 0x1000, we add a small function which copies the
vectoring code and tables to 0x0. This is fine, since the vectoring code
is position independent.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-03-31 18:28:50 +02:00
Masahiro Yamada
b4722fefd0 tegra: fix Makefile to pass per-file CFLAGS
Since Kbuild was introduced, warmboot_avp.o has been compiled
without -march=armv4t.

Makefile should be adjusted to pass a per-file option.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
2014-03-31 11:33:28 -04:00
Masahiro Yamada
254d68b601 kbuild: move asm-offsets.c from SoC directory to arch/$(ARCH)/lib
U-Boot has supported two kinds of asm-offsets.h.

One is generic for all architectures and its source is located at
./lib/asm-offsets.c.

The other is SoC specific and its source is under SoC directory.
The problem here is that only boards with SoC directory can use
the asm-offsets infrastructure.
Putting asm-offsets.c right under CPU directory does not work.

Now a new demand is coming. PowerPC folks want to use asm-offsets.
But no PowerPC boards have SoC directory.

It seems inconsistent that some boards add asm-offsets.c to SoC
directoreis and some to CPU directories.
It looks more reasonable to put asm-offsets.c under arch/$(ARCH)/lib.

This commit merges asm-offsets.c under SoC directories into
arch/$(ARCH)/lib/asm-offsets.c.

By the way, I doubt the necessity of some entries in asm-offsets.c.
I am leaving refactoring to the board maintainers.
Please check "TODO" in the comment blocks in
arch/{arm,nds32}/lib/asm-offsets.c.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Yuantian Tang <Yuantian.Tang@freescale.com>
2014-03-28 15:06:29 -04:00
Marek Vasut
b97241b312 kbuild: Rename UIMAGE to MKIMAGE
U-Boot uses the 'mkimage' tool to produce various image types,
not only uImage image type. Rename the invocation name from
UIMAGE to MKIMAGE.

The following command was used to do the replacement:
git grep 'quiet_cmd_mkimage.* = UIMAGE' | cut -d : -f 1 | \
 xargs -i sed -i "s@\(quiet_cmd_mkimage\)\(.*\) = UIMAGE @\1\2 = MKIMAGE@" {}

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-03-28 15:06:29 -04:00
Albert ARIBAUD
ab6423cae0 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Trivial merge conflict, needed to manually remove
local_info as per commit 41364f0f.

Conflicts:
	board/samsung/common/board.c
2014-03-25 10:53:15 +01:00
Marek Vasut
6e7b9f4fa0 aes: Move the AES-128-CBC encryption function to common code
Move the AES-128-CBC encryption function implemented in
tegra20-common/crypto.c into lib/aes.c . This is well re-usable common
code. Moreover, clean the code up a bit and fix the kerneldoc-style
annotations.

Signed-off-by: Marek Vasut <marex@denx.de>
2014-03-21 16:43:53 -04:00
Albert ARIBAUD
63f347ec4c Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-03-13 18:32:26 +01:00
Marek Vasut
47c9c76b8a arm: exynos: Squash bogus warnings in pinmux
Squash these warnings in pinmux.c found with GCC 4.8:

/arch/arm/cpu/armv7/exynos/pinmux.c: In function 'exynos_pinmux_config':
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'count' may be used uninitialized in this function [-Wmaybe-uninitialized]
  for (i = start; i < start + count; i++) {
                            ^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:16: note: 'count' was declared here
  int i, start, count;
                ^
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
  for (i = start; i < start + count; i++) {
                            ^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:9: note: 'start' was declared here
  int i, start, count;
         ^
/arch/arm/cpu/armv7/exynos/pinmux.c:689:19: warning: 'bank' may be used uninitialized in this function [-Wmaybe-uninitialized]
   s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
                   ^
/arch/arm/cpu/armv7/exynos/pinmux.c:662:24: note: 'bank' was declared here
  struct s5p_gpio_bank *bank;
                        ^
/arch/arm/cpu/armv7/exynos/pinmux.c: In function 'exynos_pinmux_config':
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'count' may be used uninitialized in this function [-Wmaybe-uninitialized]
  for (i = start; i < start + count; i++) {
                            ^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:16: note: 'count' was declared here
  int i, start, count;
                ^
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
  for (i = start; i < start + count; i++) {
                            ^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:9: note: 'start' was declared here
  int i, start, count;
         ^
/arch/arm/cpu/armv7/exynos/pinmux.c:689:19: warning: 'bank' may be used uninitialized in this function [-Wmaybe-uninitialized]
   s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
                   ^
/arch/arm/cpu/armv7/exynos/pinmux.c:662:24: note: 'bank' was declared here
  struct s5p_gpio_bank *bank;
                        ^

Note that the warning is bogus, the function can never be called with invalid
'peripheral' argument. GCC just cannot analyze this.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-03-13 09:46:57 +09:00
Masahiro Yamada
07e27ce013 kbuild,mxs: use short logs for MXS images
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-03-12 17:04:37 -04:00
Tom Rini
d73f38f7ba am33xx: Rework #ifdef's around s_init for clarity
The s_init function is only called on SPL or XIP cases, so lets only
build it for them.  This makes the #if logic within the function a bit
clearer as to when we are or are not calling things, and makes it easier
to see that for example preloader_console_init isn't ever called in the
non-XIP full U-Boot case.

Signed-off-by: Tom Rini <trini@ti.com>
2014-03-12 14:51:45 -04:00
Piotr Wilczek
b8dfcdb7d3 exynos4:pinmux:fdt: decode peripheral id
This patch adds api to decode peripheral id based on interrupt number.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-03-12 19:54:59 +09:00
Tom Rini
5495dae7aa Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-03-10 14:22:54 -04:00
Bo Shen
27019e4a94 arm: atmel: sama5d3: add nand spl boot support
Add NAND SPL boot support with hardware PMECC.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 19:19:13 +01:00
Bo Shen
8a45b0ba87 arm: atmel: sama5d3: add spi spl boot support
Add SPI SPL boot support for sama5d3xek board.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 19:18:33 +01:00
Andreas Henriksson
81724e09a0 at91sam9263ek: add mmc support
Add support for using the Atmel MCI driver on at91sam9263ek.
This change is modeled after the existing at91sam9260ek support.

Please note that this hooks up slot1 (MCI1) for SD. Not both.

Tested with at91bootstrap and u-boot on dataflash in slot 0
and fat-formatted 8GB SDHC in slot 1 on first revision
at91sam9263ek (which must use dataflash in slot0 to boot).

CONFIG_ATMEL_MCI_PORTB not tested.

Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se>
[remove empty line]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 18:24:52 +01:00
Masahiro Yamada
cd2e46cb38 kbuild: add CONFIG_ prefix to USE_PRIVATE_LIBGCC
Before this commit, USE_PRIVATE_LIBGCC was defined in
arch-specific config.mk and referenced in
arch/$(ARCH)/lib/Makefile.

We are not happy about parsing config.mk again and again.
We have to keep the same behavior with a different way.

By adding "CONFIG_" prefix, this macro appears
in include/autoconf.mk, include/spl-autoconf.mk.
(And treating USE_PRIVATE_LIBGCC as CONFIG macro
is reasonable enough.)

Tegra SoC family defined USE_PRIVATE_LIBGCC as "yes"
in arch/arm/cpu/arm720t/tegra*/config.mk,
whereas did not define it in arch/arm/cpu/armv7/tegra*/config.mk.

It means Tegra enables PRIVATE_LIBGCC only for SPL.
We can describe the same behavior by adding

  #ifdef CONFIG_SPL_BUILD
  # define CONFIG_USE_PRIVATE_LIBGCC
  #endif

to include/configs/tegra-common.h.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
2014-03-07 10:59:06 -05:00
Stephen Warren
716ff5ce1d ARM: tegra: simplify halt_avp()
In order to completely halt the AVP processor, we should simply write
FLOW_MODE_STOP without any extra options that allow wakeup. Amend the
code to do this.

I believe that enabling FIQ_1 and IRQ_1 allow the CPU to be awoken by
interrupts. We don't want this; if later SW wishes to use the AVP, it
should be reset and booted from scratch.

Related, the bits that were previously IRQ_1 and FIQ_1 have a slightly
different definition starting with Tegra114, so the values we're
writing don't entirely make sense there anyway.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-05 16:59:08 -07:00
Stephen Warren
f3026c1683 ARM: tegra: fix pmc_pwrgate_timer_mult register definition
Register pmc_pwrgate_timer_mult has a different layout on Tegra114 and
Tegra124. Reflect this in pmc.h.

Also, simply write the whole of the register in start_cpu() rather than
doing a read-modify-write; the register is simple enough that the code
can easily construct the entire desired value.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-05 16:59:08 -07:00
Alexey Brodkin
1ace402239 sizes.h - consolidate for all architectures
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 12:15:01 -05:00
Dave Gerlach
b56b9a0884 ARM: AM43xx: Change DDR3 Reset Value
The bit DDR3_RST_DEF_VAL inside CTRL_DDR_IO represents the default value
of the ddr reset value for DDR3 before the EMIF takes over. We must have
this bit set high so that on exit from DeepSleep0 within the kernel the
reset line has the proper value.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2014-03-04 09:42:07 -05:00
Dave Gerlach
f84880f0f3 ARM: AM43xx: Write sdram_config to secure_emif_sdram_config
The register secure_emif_sdram_config in control module is copied to
the EMIF sdram_config register when it is coming out of DeepSleep0 in
order to ensure that the EMIF comes up for the correct type of DDR.
Without this, resume can hang from within the kernel.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2014-03-04 09:42:07 -05:00
Dave Gerlach
4800be4a0c ARM: AM43xx: EMIF: configure self-refresh entry delay
Per a suggestion from the hardware team, program the emif_pwr_mgmt_ctrl
and emif_pwr_mgmt_ctrl_shdw registers within the EMIF to hold the
desired delay in cycles that the EMIF waits without an access to enter
self-refresh, in this case 8192 cycles. With this, code desiring to
enter self refresh only has to toggle one bit to enable it.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2014-03-04 09:42:07 -05:00
Mugunthan V N
2cab8ae85d ARM: AM43xx: clocks: Enable CPGMAC clock control
Enable CPGMAC clock control for AM43xx to use ethernet in U-Boot

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:06 -05:00
Tom Rini
eeb72e6761 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	arch/arm/cpu/armv7/config.mk
	board/ti/am43xx/mux.c
	include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 16:49:58 -05:00
Tom Rini
1551df35f2 arm: Switch to -mno-unaligned-access when supported by the compiler
When we tell the compiler to optimize for ARMv7 (and ARMv6 for that
matter) it assumes a default of SCTRL.A being cleared and unaligned
accesses being allowed and fast at the hardware level.  We set this bit
and must pass along -mno-unaligned-access so that the compiler will
still breakdown accesses and not trigger a data abort.

To better help understand the requirements of the project with respect
to unaligned memory access, the
Documentation/unaligned-memory-access.txt file has been added as
doc/README.unaligned-memory-access.txt and is taken from the v3.14-rc1
tag of the kernel.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 21:19:32 +01:00
Albert ARIBAUD
b60eff31f3 arm: remove unneeded symbol offsets and _TEXT_BASE
Remove the last uses of symbol offsets in ARM U-Boot.
Remove some needless uses of _TEXT_BASE.
Remove all _TEXT_BASE definitions.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-02-26 21:18:12 +01:00
Albert ARIBAUD
d0b5d9da5d arm: make _end compiler-generated
This prevents references to _end from generating absolute
relocation records.

This change is binary invariant for ARM targets.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-02-26 21:18:09 +01:00
Masahiro Yamada
4c48cfb58b arm: omap: delete unincluded omap-common/config.mk
arch/arm/cpu/armv7/omap-common/config.mk is never included
because "omap-common" is not SoC name.

If we want to add OMAP-specific compiler flags,
they must be added to omap3/config.mk, omap4/config.mk, omap5/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
2014-02-25 11:01:29 -05:00
Masahiro Yamada
630d23455b kbuild: refactor more IMX image rules
This commit avoids generating ./SPL twice.
  - Fist time descending to spl/
  - Second time as a prerequisite of u-boot-with-spl.imx,
    u-boot-with-nand-spl.imx.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-25 11:01:29 -05:00
Masahiro Yamada
4e0c8abcdd kbuild: use shorten logs for IMX images
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-25 11:01:29 -05:00
Masahiro Yamada
9bf215b035 kbuild: use shorten logs for mkimage rules
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-25 11:01:29 -05:00
Masahiro Yamada
95ddcd68ab kbuild: rename OBJCFLAGS to OBJCOPYFLAGS
Rename OBJCFLAGS to OBJCOPYFLAGS beforehand to use
"cmd_objcopy" in scripts/Makefile.lib in an upcoming commit.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-25 11:01:28 -05:00
Masahiro Yamada
f55e911ff4 arm: delete unused macro CONFIG_ARCH_DEVICE_TREE
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Rajeshwari Birje <rajeshwari.s@samsung.com>
Cc: Inderpal Singh <inderpal.singh@linaro.org>
2014-02-24 10:56:33 -05:00
Albert ARIBAUD
fae56934a0 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-02-24 10:29:59 +01:00
Darwin Rambo
989ce04999 arch: bcm281xx: Initial commit of bcm281xx architecture code
Add bcm281xx architecture support code including a clock framework and
chip reset.  Define register block base addresses for the bcm281xx
architecture and create an empty gpio header file required when
CONFIG_CMD_GPIO is set.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22 19:30:24 +01:00
Darwin Rambo
b3134fce89 arch: kona: Initial commit of kona-common architecture code
The Kona architecture is present on a number of Broadcom mobile SoCs
including the bcm281xx family of chips.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22 19:30:18 +01:00
Måns Rullgård
11f2968706 ti814x: Fix illegal use of FP ops in clock_ti814x.c
The function pll_sigma_delta_val uses "float" data which is not correct.
The exact "why" of this mangling is lost to history, but this changes us
to equivalent non-FP math to get the same results.

Reported-by: Wolfgang Denk <wd@denx.de>
Acked-by: Matt Porter <mporter@linaro.org>
2014-02-21 14:03:44 -05:00
Nishanth Menon
82da4410f8 DRA7: fix ABB efuse offset for OPP_NOM
commit 194dd74ad9
(DRA7: add ABB setup for MPU voltage domain)

Made an offset typo error by using 0x4A003B24 as the efuse offset
for OPP_NOM. As per TI documentation, 0x4A003B24 is for OPP_OD, and
0x4A003B20 is for OPP_NOM. Fix the same.

Reported-by: Praveen Rao <prao@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2014-02-21 13:55:41 -05:00
Janne Grunau
6e2192a3d8 ARM: OMAP4: fix DDR timings for OMAP4430 ES2.0
DDR timings were broken since 47abc3df70
for PandaBoard EA1.

Signed-off-by: Janne Grunau <j@jannau.net>
2014-02-21 13:55:41 -05:00
Dave Gerlach
cd8341b7eb ARM: AM43xx: GP-EVM: Correct GPIO used for VTT regulator control
Schematic indicates GPIO5_7 is to be used for VTT regulator control
rather than GPIO0_21 so modify enable_vtt_regulator to reflect this.
Without this some boards will experience DDR3 corruption and fail to
boot.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[trini: Rework patch against mainline]
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 13:55:40 -05:00
Tom Rini
4c89a369c7 Merge branch 'master' of git://git.denx.de/u-boot-spi 2014-02-21 08:00:22 -05:00
Albert ARIBAUD
3e11350255 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	Makefile
	drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
2014-02-20 13:16:05 +01:00
Masahiro Yamada
2aa43f70cf kbuild,tegra124: add dummy obj- for Kbuild
In Kbuild, every makefile must have non-empty obj- or obj-y.
Otherwise, built-in.o will not be created and the link stage
will fail.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 15:43:46 -05:00
Masahiro Yamada
ca53735a4c Move CONFIG_DISPLAY_CPUINFO to Makefile
If the whole code is surrounded by #ifdef(CONFIG_ ) .. #endif,
it should be moved to Makefile.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:10:05 -05:00
Masahiro Yamada
365475e6d1 Move #ifdef(CONFIG_DISPLAY_CPUINFO) from caller to callee
- When CONFIG_DISPLAY_CPUINFO is not enabled,
   print_cpuinfo() should be defined as an empty function
   in a header, include/common.h

 - Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
   from caller, common/board_f.c and arch/arm/lib/board.c

 - Remove redundant prototypes in arch/arm/lib/board.c,
   arch/arm/include/asm/arch-am33x/sys_proto.h and
   board/nokia/rx51/rx51.h, keeping the one in include/common.h

 - Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
   where it is missing

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:10:05 -05:00
Masahiro Yamada
7c8278a866 kbuild: add dummy obj-y to create built-in.o
We are going to switch over to Kbuild in upcoming commits.

Each makefile must have non-empty obj- or obj-y
to generate built-in.o on Kbuild.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:07:50 -05:00
Masahiro Yamada
9e4140329e kbuild: change out-of-tree build
This commit changes the working directory
where the build process occurs.

Before this commit, build process occurred under the source
tree for both in-tree and out-of-tree build.

That's why we needed to add $(obj) prefix to all generated
files in makefiles like follows:
  $(obj)u-boot.bin:  $(obj)u-boot

Here, $(obj) is empty for in-tree build, whereas it points
to the output directory for out-of-tree build.

And our old build system changes the current working directory
with "make -C <sub-dir>" syntax when descending into the
sub-directories.

On the other hand, Kbuild uses a different idea
to handle out-of-tree build and directory descending.

The build process of Kbuild always occurs under the output tree.
When "O=dir/to/store/output/files" is given, the build system
changes the current working directory to that directory and
restarts the make.

Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>"
syntax for descending into sub-directories.
(We can write it like "make $(obj)=<sub-dir>" with a shorthand.)
This means the current working directory is always the top
of the output directory.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
2014-02-19 11:07:50 -05:00
Dan Murphy
e9024ef27d ARM: O5/dra7xx: Add SATA boot support
Add the SATA boot support for OMAP5 and dra7xx.

Renamed the omap_sata_init to the common init_sata(int dev)
for commonality in with sata stack.

Added the ROM boot device ID for SATA.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-19 10:47:45 -05:00
Albert ARIBAUD
e7538fee99 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-02-19 12:04:45 +01:00
Siva Durga Prasad Paladugu
e158665c1e arm: zynq: correct the argument to lldiv
Typecast the argument with unsigned long long
for proper calculation of lldiv

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:22 +01:00
Michal Simek
d7e269cfbd zynq: Add support for U-BOOT SPL
SPL is using ps7_init.c/h files which are generated
from design tools which have to be copied to
boards/xilinx/zynq folder before compilation.

BSS section is moved to SDRAM because fat support
requires more space than SRAM size.

Added:
- MMC and QSPI support
- Boot OS directly from SPL
- Enable SPL command

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-02-19 09:41:22 +01:00
Michal Simek
96a5d4dc1e zynq: Update CLK in bdinfo
ARM has specific clk entries which should be also setup.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:22 +01:00
Soren Brinkmann
d6c9bbaad1 zynq: Implement dump clock command
Enable and implement dump clock command which shows
soc frequencies.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:22 +01:00
Soren Brinkmann
97598fcf10 net: zynq_gem: Calculate clock dividers dynamically
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Soren Brinkmann
1cd46ed2d3 net: zynq_gem: Move RCLK details out of driver
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Michal Simek
2826fd320c zynq: timer: Fix hangs if network activity attempted after about one hour
Cortex-A9 MPCore TRM' from ARM (ARM DDI 0407G ID072711) describes
in the section 4.1.1 how this value calculation should be done.

This patch fixes the problem if network activity such as ping or
tftp is attempted after u-boot has been idle for an hour,
it hangs, and cannot control-C out of it.

Signed-off-by: Uday Hegde <udayh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Soren Brinkmann
614c272511 zynq: timer: Migrate to zynq clock framework
Remove hardcoded frequencies in favor of Zynq clock framework.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Soren Brinkmann
6c3e61de3c zynq: Provide a framework to read clock frequencies
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Michal Simek
673ba27a85 zynq: Enable dcache support
Enable dcache.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:20 +01:00
Albert ARIBAUD
a87a0ce702 Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2014-02-19 07:15:01 +01:00
Sourav Poddar
b56e71e2d4 am43xx: Add qspi support
Add QSPI definitions and clock configuration support.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-02-18 22:41:08 +05:30
Tom Rini
c4d376fd1c Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-17 14:22:02 -05:00
Michal Simek
38716189d4 zynq: Fix elf header generation
This patch is here because of:
"arm: keep all sections in ELF file"
(sha1: 47ed5dd031)

Our tools expect to have elf with only LOAD header.
Without this fix also PHDR, INTERP and DYNAMIC headers
are available in ELF.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-13 15:33:00 +01:00
Stephen Warren
3cd534e455 ARM: bcm2835: config.mk isn't needed
The entries in config.mk were needed so that U-Boot could be built
with an old version of the Raspberry Pi Foundation's toolchain. Without
them, the build would error out with:

...-ld: error: .../libgcc.a(_bswapsi2.o) uses VFP register arguments,
u-boot does not

However, none of the 3 toolchains in the latest version of their
tools.git, nor the Ubuntu/Linaro ARM compilers in at least Ubuntu Quantal
or Saucy, need these options set in order to compile a working U-Boot.
Hence, remove the options for simplicity.

Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
2014-02-13 15:06:02 +01:00
Albert ARIBAUD
d53ccdb341 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-02-13 13:30:54 +01:00
Stefano Babic
17998eff90 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-11 12:55:32 +01:00
Markus Niebel
adadc915b3 ARM: imx6: fix wrong fec clk
imx_get_fecclk() returns enet_ref instead of ipg.
Since the clock is used to calculate the prescaler
for the MDIO interface wrong values can be calculated.

Tested on a custom MX6S board with 100MBit interface

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
2014-02-11 11:31:52 +01:00
Fabio Estevam
6d73c23410 mx6: Enable L2 cache support
Add L2 cache support and enable it by default.

Configure the L2 cache in the same way as done by FSL kernel:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_4.1.0

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-02-11 11:24:12 +01:00
Fabio Estevam
94db665579 mx6: Distinguish mx6dual from mx6quad
Currently when we boot a mx6dual U-boot reports that it is a mx6quad.

Report it as MX6D instead:

CPU:   Freescale i.MX6D rev1.2 at 792 MHz

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:24:12 +01:00
Anson Huang
16197bb8ba imx6: make sure MMDC_CHx_MASK is clear to avoid warm reset failure
Boot ROM may mask MMDC_CHx_MASK in CCM_CCDR(such as i.MX6SL TO1.2),
it will cause warm reset fail, need to clear this MMDC_CHx_MASK field
to make sure all the i.MX6 series SOCs reset function work. Otherwise,
uboot "reset" command will fail, tested on i.MX6SL EVK board with TO1.2.

Signed-off-by: Anson Huang <b20788@freescale.com>
2014-02-11 11:24:01 +01:00
Anson Huang
5c92edc21c imx6: ensure AHB clock is 132MHz in low freq boot mode
For low freq boot mode(ARM boot up with 396MHz), ROM
will not set AHB clock to 132MHz, and the reset value of
AHB divider is incorrect which will lead to wrong AHB
rate, need to correct it. To enable low freq boot mode,
need to set BOOT_CFG2[2] to high, tested on i.MX6Q/DL
SabreSD board and i.MX6SL EVK board.

Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Anson Huang <b20788@freescale.com>
2014-02-11 11:17:10 +01:00
Inha Song
e25bfecf7b exynos: clock: use the clear and set bits macros.
Use setbits/clrbits macro instead of readl/writel function.
(Suggested by Wolfgang)

Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-10 16:01:44 +09:00
Inha Song
3cb007a9f2 exynos: clock: fixed that cfg is set to wrong value.
This patch fixed that cfg value is set to wrong value.
Because it didn't read the related register.

Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-10 16:00:27 +09:00
Tom Rini
7dbe63bc95 SPL: Add CONFIG_SUPPORT_EMMC_BOOT support to CONFIG_SPL_FRAMEWORK
We use the switch CONFIG_SUPPORT_EMMC_BOOT today to enable some
additional features of the eMMC boot partitions.  Add support for being
told that we have booted from one of these partitions to the spl
framework and implement this on TI OMAP/related.

Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:48 +02:00
Marek Vasut
c8d4b2f826 ARM: IXP: Remove the IXP architecture support
The architecture is unmaintained and dead, remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:52 +01:00
Minkyu Kang
0ab9a03ca4 exynos: pinmux: remove unnecessary routine
Because of the list of peripherals is not sequential,
such a routine does not check for valid correctly.
Error check will be done when call the exynos_pinmux_config function.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
2014-02-05 15:37:56 +09:00
Minkyu Kang
1501cc9416 exynos: pinmux: remove unnecessary define
The value of PERIPH_ID_COUNT was wrong, and unnecessary.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-05 15:37:56 +09:00
Tom Warren
2f5dac9214 ARM: tegra: add common (shared) CPU files
These files are used by both SPL and main U-Boot.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Tom Warren
52ef43b052 ARM: tegra: Add CPU (armv7) files for Tegra124
These files are for code that runs on the CPU (A15) on Tegra124 boards.
At this time, there is no A15-specific code here. The warmboot/LP0 files
aren't included as that code hasn't been ported yet.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Tom Warren
32edd2ede2 ARM: tegra: add SPL/AVP (arm720t) CPU files for Tegra124
This provides SPL support for Tegra124 boards - AVP early init, plus
CPU (A15) init/jump to main U-Boot.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Stephen Warren
a4bcd67c72 ARM: tegra: remove a conditional for CSITE rate
There's already an SoC-specific conditional in cpu.h to determine the
PLLP rate. Define the CSITE clock rate inside the same conditional, so
that we can remove a conditional from clock_enable_coresight(). This
means one less place to update the code for new SoCs.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Stephen Warren
41447fb2cf ARM: tegra: enable PLLX only once it's been fully configured
This programming sequence is correct per Jimmy Zhang, and makes sense
too!

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Stephen Warren
cad38a57d3 ARM: tegra: pass just partition ID to power_partition()
Pass just the partition ID to power_partition(), rather than also passing
the partition's status register mask too. This makes it simpler to get
call-sites correct, since they don't need to pass two different values
that define the same thing and must match.

Consequently, we can remove the mask definitions from pmc.h.

Suggested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Stephen Warren
41cd530d6d ARM: tegra: misc cleanups triggered by Tegra124 review
Use a named constant for the PLL lock bit in enable_cpu_clocks().

Construct the complete value of pmc_pwrgate_toggle, rather than doing a
read-modify-write; the register is simple enough and doesn't need to
maintain state between operations.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:46 -07:00
Jimmy Zhang
b9dd6215ce ARM: tegra: don't exceed AVP limits when configuring PLLP
Based on the Tegra TRM, the system clock (which is the AVP clock) can
run up to 275MHz. On power on, the default sytem clock source is set to
PLLP_OUT0. In function clock_early_init(), PLLP_OUT0 will be set to
408MHz which is beyond system clock's upper limit.

The fix is to set the system clock to CLK_M before initializing PLLP,
and then switch back to PLLP_OUT4, which has an appropriate divider
configured, after PLLP has been configured

Implement this logic in new function tegra30_set_up_pllp(),
which sets up PLLP and all PLLP_OUT* dividers, and handles the AVP
clock switching. Remove the duplicate PLLP setup from pllx_set_rate()
and adjust_pllp_out_freqs().

Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
[swarren, significantly refactored the change]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Stephen Warren
9399e540ca ARM: tegra: amend pmc.h for Tegra114+
Tegra114 and later's PMC module removes the pwrgate_timer_on register
and replaces it with a clamp_status register. Adjust pmc.h to reflect
this, and update any code affected by the change.

The cpu.c change in this patch was extracted from a much larger patch
by Jimmy Zhang. The pmc.h change was written from scratch, but inspired
by related changes made by Tom Warren.

There could well be other differences in the PMC register set for chips
after Tegra20/30. However, they don't affect the code in U-Boot at
present, so I haven't attempted an exhaustive update of pmc.h.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Tom Warren
c82014daf5 ARM: tegra: implement MASK_BITS_31_29
Some clock sources have 3-bit muxes in bits 31:29. Implement core
support for this mux field.

Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, extracted from a larger patch by Tom]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Stephen Warren
54d2e18292 ARM: tegra: use MASK_BITS_* macros everywhere
Not all code that set or interpreted "mux_bits" was using the named
macros, but rather some was simply using hard-coded integer constants.
This makes it hard to determine which pieces of code are affected by
changes to those constants.

Replace the integer constants with the equivalent macro definitions so
that everything is nicely tied together.

Note that I'm not convinced all the code was using the correct integer
constants, and hence I'm not convinced that all the code is now using
the desired macros. However, this change is a purely mechanical
replacement and should have no functional change. Fixing any bugs will
come later, separately.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Stephen Warren
9cb0c6dc69 ARM: tegra: rename OUT_CLK_SOURCE_*
OUT_CLK_SOURCE_ are currently named after the number of bits the mask
they represent includes. However, bit count is not the only possible
variable; bit position may also vary. Rename OUT_CLK_SOURCE_ to
OUT_CLK_SOURCE_31_30_ and OUT_CLK_SOURCE4_ to OUT_CLK_SOURCE_31_28 to
more completely describe exactly what they represent, without having to
go look up the definitions.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Stephen Warren
5916a36ee9 ARM: tegra: rename MASK_BITS_29_28 to MASK_BITS_31_28
The only place where the MASK_BITS_* values are used is in
adjust_periph_pll(), which interprets the value 4 (old MASK_BITS_29_28,
new MASK_BITS_31_28) as being associated with mask OUT_CLK_SOURCE4_MASK,
i.e. bits 31:28. Rename the MASK_BITS_ macro to reflect how it's actually
implemented.

Note that no Tegra clock register actually uses all of bits 31:28 as
the mux field. Rather, bits 30:28, 29:28, or 28 are used. However, in
those cases, nothing is stored in the bits above the mux field, so it's
safe to pretend that the mux field extends all the way to the end of the
register. As such, the U-Boot clock driver is currently a bit lazy, and
doesn't distinguish between 31:28, 30:28, 29:28 and 28; it just lumps
them all together and pretends they're all 31:28. This patch doesn't
cause this issue; it was pre-existing. Hopefully, future patches will
clean this up.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Tom Warren
0b01b53aa5 ARM: tegra: deduplicate MASK_BITS_xxx clock mux enum
The enum used to define the set of register bits used to represent a
clock's input mux, MUX_BITS_*, is defined separately for each SoC at
present. Move this definition to a common location to ease fixing up
some issues with the definition, and the code that uses it.

Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, extracted from a larger patch by Tom]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:44 -07:00
Stephen Warren
86b657878b ARM: tegra: accept any SKU ID for most chips
For Tegra20, the SKU ID actually impacts how U-Boot programs the chip,
and hence we need to explicitly know about each and every SKU ID in order
to operate correctly.

However, for Tegra30/114, this isn't the case. Rather than forcing each
new user with a different SKU to manually add their SKU ID into the code,
simply accept any SKU ID.

If U-Boot ever starts e.g. programming maximal CPU clocks etc., we'll
need to undo this, or make the default case map to conservative defaults,
but for now it's likely the path to least support cost.

Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:44 -07:00
Albert ARIBAUD
e97f9d817e Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-01-29 14:07:50 +01:00
Marek Vasut
7981449280 ARM: mx6: Add PCI express clock configuration
Split the SATA clock enabling function and add PCI express clock
enabling function. The SATA clock enabling function starts up the
100MHz SATA reference PLL in ENET_PLL register, but the code can
be re-used to enable the 125MHz PCIe reference in ENET_PLL, so pull
this code into separate function. Moreover, add the PCIe clock
enabling code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-01-26 12:41:20 +01:00
Marek Vasut
7cbe638e41 ARM: armv7: Make indirect vector addresses globl
Make indirect vectors addresses global, so they can be replaced by
various code that needs to do so. For example the MX6 PCI express
driver needs to temporarily replace data abort handler when reading
the config space.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2014-01-26 12:41:20 +01:00
Stefano Babic
707acd01de Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-01-26 12:11:54 +01:00
Masahiro Yamada
bf1af3d872 ARM: merge commonly-defined PLATFORM_RELFLAGS
Before this commit, all arch/arm/cpu/${CPU}/config.mk except ARMv8
had the same option:
$(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,))

This commit moves it into arch/arm/config.mk.

If the compiler does not support the option,
it is ignored by $(call cc-option,...).
So this commit gives no harm to ARMv8.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:08 -05:00
Darwin Rambo
de351d6be6 lib: time: add weak timer_init() function
If timer_init() is made a weak stub function, then it allows us to
remove several empty timer_init functions for those boards that
already have a timer initialized when u-boot starts. Architectures
that use the timer framework may also remove the need for timer.c.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
2014-01-24 16:59:06 -05:00
Nishanth Menon
194dd74ad9 DRA7: add ABB setup for MPU voltage domain
Patch adds modification to shared omap5 abb_setup() function, and
proper registers definitions needed for ABB setup sequence. ABB is
initialized for MPU voltage domain at OPP_NOM.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-01-24 11:41:17 -05:00
Nishanth Menon
3ac8c0bf65 DRA7: Add support for ES1.1 silicon ID code
ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support
for ES1.1 IDCODE change.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-01-24 11:41:17 -05:00
Jassi Brar
e81f63f0d2 ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALL
The commit
f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2014-01-24 09:38:39 -05:00
Jassi Brar
02c41535b6 ARM: OMAP4/5: Remove dead code against CONFIG_SYS_CLOCKS_ENABLE_ALL
The commit
 f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2014-01-24 09:34:22 -05:00
Stephen Warren
004c10598b ARM: bcm2835: fix mailbox timeout
My original intention was to have a 100ms timeout. However, the timer
operations used return values in ms not us, so we ended up with a 100s
timeout instead. Fixing this exposes that some operations need longer
to operate than 100ms, so bump the timeout up to a whole second.

Reported-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-01-20 17:11:39 -05:00
Tom Rini
4641c211f6 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-01-20 07:33:42 -05:00
Fabio Estevam
be2a3bb39a mx6: Revert "mx6: soc: Disable VDDPU regulator"
Commit 022298278 (mx6: soc: Disable VDDPU regulator) is causing kernel hang
for people using FSL kernel 3.0.35 and 3.10, so revert it for now.

Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Reported-by: Pierre Aubert <p.aubert@staubli.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-17 10:16:48 +01:00
Albert ARIBAUD
bf46e7d8d1 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-01-15 15:18:04 +01:00
Fabio Estevam
5f98d0b5d3 mx6: clock: Pass the frequency as argument of enable_fec_anatop_clock()
Provide an argument to enable_fec_anatop_clock() to specify the clock frequency
that will be generated.

No changes are made to mx6slevk, which uses the default 50MHz fec clock.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-15 10:33:25 +01:00
Andreas Bießmann
6ba2bc8fa9 arm: use canonical sub mnemonic
Building some arm boards with older binutils may produce errors like this:

---8<---
crt0.S: Assembler messages:
crt0.S:70: Error: register expected, not '#(184)' -- `sub sp,#(184)'
--->8---

Use canonical version of the subtract mnemonic to avoid those issues.

Reported-by: Alexey Smishlayev <alexey@xtech2.lv>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-01-14 12:38:47 +01:00
Albert ARIBAUD
e6fe4bd989 Merge 'u-boot-imx/master' into 'u-boot-arm/master' 2014-01-14 11:50:54 +01:00
Albert ARIBAUD
b02bfc4dfc arm: put .hash, .got.plt and .machine_param back in binaries
Some targets will build fine but not boot if sections .hash and
.got.plt are not present in the binary. Add them back.

Also, Exynos machines require .machine_param section in SPL.
Add it.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
2014-01-14 11:43:10 +01:00
Marek Vasut
67decc71ed ARM: pxa: Fix OneNAND SPL builds
The OneNAND SPL used on PXA is slightly obscure. Due to the OneNAND limitation,
where we have only the first 1KiB of the OneNAND available upon power-up as a
memory-mapped area, from which the CPU starts executing, we place only the most
essential code into this first 1KiB . This code copies the rest of the SPL into
SRAM and jumps to it. This code is stored in section .text.0 .

The rest of the SPL is stored in section .text.1 . When running the OBJCOPY on
the SPL, it will preserve only .text section, but the .text.0 and .text.1 are
stripped away from the result, thus making the SPL binary empty. The patch adds
additional -j parameters to the OBJCOPY for PXA during the SPL build, which will
preserve the .text.0 and .text.1 sections.

Moreover, this patch also adds missing functions into the .text.0 section, since
otherwise the PXA270 with 1KiB-window OneNAND won't be able to boot.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
2014-01-13 12:39:10 +01:00
Christian Gmeiner
5a66016987 imx6: make use of lldiv(..)
Commit 762a88ccf8 introduces
a 64-bit division without using the lldiv() function,
which pulls in previously unused libgcc stuff.

Signed-off-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-13 11:52:28 +01:00
Tom Rini
7f673c99c2 Merge branch 'master' of git://git.denx.de/u-boot-arm
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.

Conflicts:
	include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-01-10 10:56:00 -05:00
Jagannadha Sutradharudu Teki
b3de92495f zynq: Add support to find bootmode
Added support to find the bootmodes by reading
slcr bootmode register. this can be helpful to
autoboot the configurations w.r.t a specified bootmode.

Added this functionality on board_late_init as it's not
needed for normal initializtion part.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
David Feng
0ae7653128 arm64: core support
Relocation code based on a patch by Scott Wood, which is:
Signed-off-by: Scott Wood <scottwood@freescale.com>

Signed-off-by: David Feng <fenghua@phytium.com.cn>
2014-01-09 16:08:44 +01:00
Albert ARIBAUD
4b0561d841 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-01-06 09:32:42 +01:00
Albert ARIBAUD
a891601ce5 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Conflicts:
	include/micrel.h

The conflict above was trivial, caused by four lines being
added in both branches with different whitepace.
2014-01-06 08:49:58 +01:00
Sergey Alyoshin
4611d5bab2 arm: mx5: Add fuse supply enable in fsl_iim
Enable fuse supply before fuse programming and disable after.

Signed-off-by: Sergey Alyoshin <alyoshin.s@gmail.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2014-01-03 15:44:06 +01:00
Otavio Salvador
c655b816e5 ARM: mx6: Allow enablement of FEC Anatop based clock for all MX6
The enable_fec_anatop_clock method should be available for all MX6
variant as it is not MX6 SoloLite specific. This moves the code out of
the #ifdef/#endif and we make it conditional to CONFIG_FEC_MXC
instead.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-03 15:44:05 +01:00
Fabio Estevam
0222982780 mx6: soc: Disable VDDPU regulator
As U-boot does not use GPU/VPU peripherals, shutdown the VDDPU regulator
in order to save power.

Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:51 +01:00
Fabio Estevam
39f0ac9347 mx6: soc: Add the required LDO ramp up delay
When changing LDO voltages we need to wait for the required amount of time
for the voltage to settle.

Also, as the timer is still not available when arch_cpu_init() is called, we
need to call it later at board_postclk_init() phase.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:51 +01:00
Fabio Estevam
3d622b78bd mx6: soc: Introduce set_ldo_voltage()
Introduce set_ldo_voltage() so that all three LDO regulators can be configured.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:51 +01:00
Fabio Estevam
7e5e8c94a9 mx6: soc: Set the VDDSOC at 1.175 V
mx6 datasheet specifies that the minimum VDDSOC at 792 MHz is 1.15 V.
Add a 25 mV margin and set it to 1.175V.

This also matches the VDDSOC voltages for 792MHz operation that the kernel configures:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/cpu_op-mx6.c?h=imx_3.0.35_4.1.0

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:50 +01:00
Fabio Estevam
e113fd1972 mx6: soc: Clear the LDO ramp values up prior to setting the LDO voltages
Since ROM may modify the LDO ramp up time according to fuse setting,
it is safer to reset the ramp up field to its default value of 00:

00: 64 cycles of 24MHz clock;
01: 128 cycles of 24MHz clock;
02: 256 cycles of 24MHz clock;
03: 512 cycles of 24MHz clock;

Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:50 +01:00
Fabio Estevam
fc740648bd mx6: soc: Staticize set_vddsoc()
set_vddsoc() is not used anywhere else, so make it static.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02 17:16:50 +01:00
Rajeshwari Birje
5af4a4f74a Exynos5420: Add support for 5420 in pinmux and gpio
Adds code in pinmux and gpio framework to support Exynos5420.

Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30 16:50:34 +09:00
Rajeshwari Birje
f3d7c2fe9d Exynos5420: Add DDR3 initialization for 5420
This patch intends to add DDR3 initialization code for Exynos5420.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30 16:50:34 +09:00
Rajeshwari Birje
060c227a28 Exynos5420: Add clock initialization for 5420
This patch adds code for clock initialization and clock settings
of various IP's and controllers, required for Exynos5420

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30 16:50:34 +09:00
Lokesh Vutla
b5e01eecc8 ARM: AM43xx: GP_EVM: Add support for DDR3
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:45 -05:00
Lokesh Vutla
d3daba10f1 ARM: AM43xx: EPOS_EVM: Add support for LPDDR2
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:44 -05:00
Lokesh Vutla
965de8b91b ARM: AM33xx+: Update ioregs to pass different values
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-18 21:14:18 -05:00
Lokesh Vutla
cf04d0326b ARM: AM43xx: clocks: Update DPLL details
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50	300MHz
OPP100	600MHz
OPP120	720MHz
OPPTB	800MHz
OPPNT	1000MHz
According to the latest DM following is the OPP table dependencies:
	VDD_CORE 	VDD_MPU
	OPP50		OPP50
	OPP50 		OPP100
	OPP100		OPP50
	OPP100		OPP100
	OPP100		OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz

Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:01 -05:00
Lokesh Vutla
0d54cb924e ARM: AM43xx: Select clk source for Timer2
Selecting the Master osc clk as Timer2 clock source.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:01 -05:00
Albert ARIBAUD
d627eefcd5 Merge remote-tracking branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2013-12-18 22:19:02 +01:00
Alban Bedel
3346cbb8e8 ARM: tegra: support SKU b1 of Tegra30
Add the Tegra30 SKU b1 and treat it like other Tegra30 chips.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Julian Scheel <julian.scheel@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-18 10:19:48 -07:00
Thierry Reding
4475c7752d Tegra114: Do not program CPCON field for PLLX
PLLX no longer has the CPCON field on Tegra114, so do not attempt to
program it.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-18 10:19:48 -07:00
Jimmy Zhang
44de8e22ec Tegra114: Fix PLLX M, N, P init settings
The M, N and P width have been changed from Tegra30. The maximum value
for N is limited to 255. So, the tegra_pll_x_table for Tegra114 should
be set accordingly.

Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Reviewed-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-18 10:19:48 -07:00
Sergei Ianovich
23f00caf6e ARM: pxa: prevent PXA270 occasional reboot freezes
Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.

If SDRAM is not reset, it causes memory bus congestion and
the device hangs.

We put SDRAM in selfresh mode before watchdog reset, removing
potential freezes.

Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
2013-12-18 16:00:37 +01:00
Frank Li
ebaf6b26bc imx6: fix random hang when download by usb
ROM did not invalidate L1 cache when download by usb
Need invalidate L1 cache before enable cache

Signed-off-by: Huang yongcai <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
2013-12-17 18:48:45 +01:00
Fabio Estevam
89cfd0f575 mx6: clock: Fix the calculation of PLL_ENET frequency
According to the mx6 quad reference manual, the DIV_SELECT field of register
CCM_ANALOG_PLL_ENETn has the following meaning:

"Controls the frequency of the ethernet reference clock.
- 00 - 25MHz
- 01 - 50MHz
- 10 - 100MHz
- 11 - 125MHz"

Current logic does not handle the 25MHz case correctly, so fix it.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-12-17 18:38:42 +01:00
Tom Rini
49a90e2975 ARM:PXA: Correct tick_to_time / us_to_tick to use lldiv
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
2013-12-13 09:16:20 -05:00
Tom Rini
e83bab8403 ARM:zynq: Correct __udelay to use lldiv
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-13 09:16:20 -05:00
Lokesh Vutla
d2c7074b95 ARM: OMAP5: clocks: Update MPU settings for OPP_NOM
As per the latest 0.6 version of DM for OMAP5430 ES2.0,
MPU_GCLK is given as 1000MHz. In order to achieve this DPLL_MPU
should be locked at 2000MHz. Fixing the same and cleaning the
previously used dpll values.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-12 17:43:39 -05:00
Lokesh Vutla
5298f21ab3 ARM: DRA7xx: Change clk divider setting
Commit "armv7: hw_data: change clock divider setting"
updates the setting for m6 divider for 20MHz sys_clk frequency.
But missed to update for other sys_clk frequencies. Doing the same.

Reported-by: Rajendran, Vinothkumar <vinothr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-12 17:43:39 -05:00
Nikita Kiryanov
47b4bcf785 arm: omap: abb: add missing include
ABB code uses LDELAY but does not include the header that provides its
definition.

Include the header.

Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Nishanth Menon <nm@ti.com>
2013-12-12 14:54:22 -05:00
Tom Rini
12115c6ad3 am33xx: Enable D-CACHE on !CONFIG_SYS_DCACHE_OFF
Test on Beaglebone white over cpsw, usb ether and SD card (read and
write), performance increased, crc32 of data matches.

Signed-off-by: Tom Rini <trini@ti.com>
2013-12-12 14:54:12 -05:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00
Andreas Bießmann
bcf9fe37f5 at91: switch coloured LED to gpio API
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-09 13:21:47 +01:00
Albert ARIBAUD
47ed5dd031 arm: keep all sections in ELF file
Current LDS files /DISCARD/ a lot of sections when linking ELF
files, causing diagnostic tools such as readelf or objdump to
produce partial output. Keep all section at link stage, filter
only at objcopy time so that .bin remains minimal.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-12-07 06:53:58 +01:00
Masahiro Yamada
3064d599af ARM: align MVBAR on 32 byte boundary
The lower 5 bit of MVBAR is UNK/SBZP.
So, Monitor Vector Base Address must be 32-byte aligned.
On the other hand, the secure monitor handler does not need
32-byte alignment.

This commit moves ".algin 5" directive to the correct place.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andre Przywara <andre.przywara@linaro.org>
Acked-by: Andre Przywara <andre.przywara@linaro.org>
2013-12-06 21:03:35 +01:00
Albert ARIBAUD
375a4496ff Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2013-12-06 16:54:42 +01:00
Albert ARIBAUD
c35cf8dc9f Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-12-06 14:26:51 +01:00
Michael Trimarchi
f33b9bd398 arm: omap3: Enable clocks for peripherals only if they are used
This patch change the per_clocks_enable() function used in OMAP3
code to enable peripherals clocks. Only required clock should be
activated. So if the board use the uart(x) as a console we need
to activate it. The Board's config should include define to enable
every subsystem that the board use. For a complete list
of affected peripherals, registers CM_FCLKEN_PER and CM_ICLKEN_PER
should be checked.
Right now the bootloader can enable and disable clocks for:
uart(x) using CONFIG_SYS_NS16550
gpio bank (x) using CONFIG_OMAP3_GPIO_X with X = { 2, 3, 4, 5, 6 }
i2c bus using CONFIG_DRIVER_OMAP34XX_I2C.

Not required gptimer(x) and mcbsp(x) for booting are disabled by default and
are not supported by any define.
Their activation need to included in the per_clocks_enable if the
peripheral is included. Not booting board should enable the peripheral
clock connected to their driver

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-12-06 07:02:32 -05:00
Minkyu Kang
d8fa31a71f arm: exynos: adds ifdef for spi boot
This patch fix following errors and warnings

spl_boot.c: In function 'exynos_spi_copy':
spl_boot.c:111:49: error: 'CONFIG_ENV_SPI_BASE' undeclared (first use in this function)
spl_boot.c:111:49: note: each undeclared identifier is reported only once for each function it appears in
spl_boot.c:142:2: error: 'SPI_FLASH_UBOOT_POS' undeclared (first use in this function)
spl_boot.c: In function 'copy_uboot_to_ram':
spl_boot.c:189:28: warning: unused variable 'param' [-Wunused-variable]
spl_boot.c: At top level:
spl_boot.c:107:13: warning: 'exynos_spi_copy' defined but not used [-Wunused-function]

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-12-06 19:07:47 +09:00
Albert ARIBAUD
7988bd4ed6 Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master' 2013-12-06 10:41:49 +01:00
Hardik Patel
675cc77a3a pandaboard: 1/1] ARM:OMAP4+: panda-es: Support Rev B3 Elpida DDR2 RAM
Signed-off-by: Hardik Patel <hardik.patel@volansystech.com>
2013-12-04 11:41:13 -05:00
Lokesh Vutla
642cdc13f6 ARM: OMAP5+: Remove unnecessary EFUSE settings
Certain EFUSE settings were recommended for the first
four lots of OMAP5 ES1.0 silicon. These are not applicable
for OMAP5 ES2.0 and DRA7 silicon. So removing these EFUSE settings.

Reported-by: Griffis, Brad <bgriffis@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-04 08:12:38 -05:00
Roger Quadros
5afded6a4c ARM: DRA7xx: Add PRCM and Control information for SATA
Adds the necessary PRCM and Control register information for
SATA on DRA7xx.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
Roger Quadros
a087a7fb92 ARM: OMAP5: Add SATA platform glue
Add platform glue logic for the SATA controller.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
Roger Quadros
8ffcf74bb0 ARM: OMAP5: Add PRCM and Control information for SATA
Adds the necessary PRCM and Control register information for
SATA on OMAP5.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
Roger Quadros
9c4b64fb61 ARM: OMAP5: Add Pipe3 PHY driver
Pipe3 PHY is used by SATA, USB3 and PCIe modules. This is
a driver for the Pipe3 PHY.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:08 -05:00
SRICHARAN R
54d022e76c ARM: DRA7/OMAP5: EMIF: Add workaround for bug 0039
When core power domain hits oswr, then DDR3 memories does not come back
while resuming. This is because when EMIF registers are lost, then the
controller takes care of copying the values from the shadow registers.
If the shadow registers are not updated with the right values, then this
results in incorrect settings while resuming. So updating the shadow registers
with the corresponding status registers here during the boot.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-12-04 08:12:08 -05:00
SRICHARAN R
6c70935d75 ARM: DRA: EMIF: Change DDR3 settings to use hw leveling
Currently the DDR3 memory on DRA7 ES1.0 evm board is enabled using
software leveling. This was done since hardware leveling was not
working. Now that the right sequence to do hw leveling is identified,
use it. This is required for EMIF clockdomain to idle and come back
during lowpower usecases.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-12-04 08:12:08 -05:00
Tom Rini
39245c8699 am33xx: Stop modifying certain EMIF4D registers
Based on the definitive guide to EMIF configuration[1] certain registers
that we have been modifying (and are documented registers) should be
left in their reset values rather than modified.  This has been tested
on AM335x GP EVM and Beaglebone White.

[1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
2013-12-04 08:11:45 -05:00
Lubomir Popov
87b94a43d6 ARM: OMAP4: Fix bug in omap4470_volts struct
The struct incorrectly referenced SMPS1 for all three power
domains. Fixed this by using SMPS2 and SMPS5 as appropriate.

Add some comments and choose voltage values that correspond
to voltage selection codes.

Signed-off-by: Lubomir Popov <l-popov@ti.com>
2013-12-04 08:11:28 -05:00
Chin Liang See
4c54419737 socfpga: Adding Freeze Controller driver
Adding Freeze Controller driver. All HPS IOs need to be
in freeze state during pin mux or IO buffer configuration.
It is to avoid any glitch which might happen
during the configuration from propagating to external devices.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-03 14:38:56 +01:00
Rajeshwari Shinde
347e45d745 exynos: spl: Add a custom spi copy function
This patch implements a custom spi_copy funtion to copy u-boot from SF
to RAM. This is faster then iROM spi_copy funtion as this runs spi at
50Mhz and also in WORD mode of operation.

Changed a printf in pinmux.c to debug just to avoid the compilation
error in SPL.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-03 15:26:33 +09:00
Nobuhiro Iwamatsu
cae83ce515 arm: rmobile: Remove config.mk
Renesas ARM SoCs (R-Mobile, R-Car) are armv7 only.
This drops armv5 supprt from PLATFORM_CPPFLAGS and remove config.mk of
rmobile.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-12-03 09:47:15 +09:00
Nobuhiro Iwamatsu
7579751c14 arm: kzm9g: Fix undefined reference to `__aeabi_uldivmod' error
The kzm9g board fails in building with -march=armv7-a.
This fixs this problem by converting to do_div().

-----
USE_PRIVATE_LIBGCC=yes ./MAKEALL kzm9g
...
arch/arm/cpu/armv7/rmobile/librmobile.o: In function `get_time_us':
arch/arm/cpu/armv7/rmobile/timer.c:41: undefined reference to `__aeabi_uldivmod'
arch/arm/cpu/armv7/rmobile/librmobile.o: In function `get_time_ms':
arch/arm/cpu/armv7/rmobile/timer.c:47: undefined reference to `__aeabi_uldivmod'
-----

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
2013-12-03 09:47:08 +09:00
Nobuhiro Iwamatsu
bd0550fc5f arm: rmobile: Add support R8A7791
Renesas R8A7791 is CPU with Cortex-A15.
This supports the basic register definition and GPIO and
framework of PFC.

Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-03 09:46:45 +09:00
Nobuhiro Iwamatsu
1d0e92782f arm: rmobile: Add support R8A7790
Renesas R8A7790 is CPU with Cortex-A7 and A15.
This supports the basic register definition and GPIO and
framework of PFC.

Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-03 09:45:20 +09:00
Nobuhiro Iwamatsu
941b5a40a5 arm: rmobile: Move lowlevel_init.o to taget of each CPU
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2013-12-03 09:42:28 +09:00
Jaehoon Chung
a85ca22f62 arm: exynos: fix set_mmc_clk for exynos4x12
Fix the set_mmc_clk() for exnos4x12.
If board is exynos4x12, mmc clock should be set to wrong value.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-03 09:39:46 +09:00
Albert ARIBAUD
77524d2c9d Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master' 2013-12-02 16:00:10 +01:00
Heiko Schocher
4535a24c0c arm926ejs, at91: add common phy_reset function
add common phy reset code into a common function.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Jens Scharsig <esw@bus-elektronik.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Markus Hubig <mhubig@imko.de>
Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01 22:38:52 +01:00
Bo Shen
c5e8885aab arm: atmel: sama5d3: spl boot from fat fs SD card
Enable Atmel sama5d3xek boart spl boot support, which can load u-boot
from SD card with FAT file system.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01 22:38:51 +01:00
Bo Shen
9d9289cb31 arm: atmel: add ddr2 initialization function
The MPDDRC supports different type of SDRAM
This patch add ddr2 initialization function

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01 22:38:47 +01:00
Bo Shen
184c551b85 arm: atmel: sama5d3: correct the ID for DBGU and PIT
As the DBGU and PIT has its own ID on sama5d3 SoC, while not share
with SYS ID. So, correct them.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01 22:38:39 +01:00
Tom Rini
faca8ff55f Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2013-11-25 10:42:13 -05:00
Albert ARIBAUD
d44a5f5128 Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master' 2013-11-22 10:19:35 +01:00
pekon gupta
2c17e6d1d9 am335x: fix GPMC config for NAND and NOR SPL boot
GPMC controller is common IP to interface with both NAND and NOR flash devices.
Also, it supports max 8 chip-selects, which can be independently connected to
any of the devices.
But ROM code expects the boot-device to be connected to only chip-select[0].
Thus to resolve conflict between NOR and NAND boot. This patch:
- combines NOR and NAND configs spread in board files to common gpmc_init()
- configures GPMC based on boot-mode selected for SPL boot.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
pekon gupta
beba5f04f2 mtd: nand: omap: make am33xx/elm.c as common driver for all OMAPx and AMxxxx platforms
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
	and include in all board configs using AM33xx SoC platform.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
Masahiro Yamada
a52f90f074 arm: rmobile: Do not create a symbolic link to sh timer
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-11-17 14:11:33 -05:00
Tom Rini
5e995c00f6 TI:omap: Update u-boot-spl.lds for i2c multibus/multiadapter update
In 6789e84 we update u-boot-spl.lds for OMAP to ensure we include
adapter information, as we use i2c during SPL.  However, the regex used
also means we included commands that may have been built.  On omap5_uevm
this leads to a failure as we include the command from the do_tca642x
command, and fail to link.  The fix is to restrict our regex to only the
i2c list parts.

Signed-off-by: Tom Rini <trini@ti.com>
2013-11-15 12:20:33 -05:00
Wu, Josh
618bbbb2e9 ARM: at91: sama5d3: add support for sama5d36 chip
The SAMA5D36 chip is the superset product of SAMA5D3x family.

For detail information please refer to:
  http://www.atmel.com/Microsite/sama5d3/default.aspx

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-13 22:18:18 +01:00
Heiko Schocher
6789e84eca i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13 06:18:17 +01:00
Heiko Schocher
16678eb40f arm, am33x: make RTC32K OSC enable configurable
As
http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast
states:
"Initialize devices only when they are needed within U-Boot"

enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is
enabled. Enable this in ti_am335x_common.h, so all boards in mainline
should work as before.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-11-11 12:16:30 -05:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
Albert ARIBAUD
3285d4ca19 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-11-07 09:32:16 +01:00
Radhey Shyam Pandey
b5f05b0634 arm: zynq : Revert TZ_DDR_RAM to secure.
TZ_DDR_RAM on reset is in secure mode.
Since uboot and linux runs in full
TZ privilege secure mode, no need
to set DDR trustzone to non-secure.

Signed-off-by: Radhey Shyam Pandey <radheys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-11-06 09:24:06 +01:00
Michal Simek
c1824ea268 arm: zynq: Do not remap OCM to high address
In case where ps-ddr is not used, do not remap
OCM to high address and keep it from 0x0.
Linux SMP requires to have memory at 0x0.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-11-06 09:23:58 +01:00
Rob Herring
5b6da28352 ARM: versatile: convert to common timer code
Convert versatile to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:24:22 -05:00
Rob Herring
31df9893b9 ARM: tegra: convert to common timer code
Convert tegra to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:24:22 -05:00
Rob Herring
23ab7ee0ff ARM: socfpga: convert to common timer code
Convert socfpga to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:23:45 -05:00
Rob Herring
3dae5b510e ARM: mx25: convert to common timer code
Convert mx25 to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:09:34 -05:00
Rob Herring
9df1bd416d ARM: highbank: convert to common timer code
Convert highbank to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:08:10 -05:00
Tom Rini
6843918e00 am335x: Enable CONFIG_OMAP_WATCHDOG support
There is a board-specific portion for calling watchdog enable itself, in
main U-Boot.

Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01 15:55:59 -04:00
Tom Rini
155d424a9a am33xx, davinci: Create and use <asm/davinci_rtc.h>
Create a common header file for the RTC IP block that is shared between
davinci and am33xx.

Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01 15:30:22 -04:00
Masahiro Yamada
09ab61c660 ARM: s5pc, exynos: move Samsung ARM SoC specific code under arch/arm/
This patch moves S5PC, EXYNOS specific directory entries
from the toplevel Makefile to arch/arm/cpu/armv7/Makefile
using Kbuild descending feature.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
2013-10-31 13:26:44 -04:00
Masahiro Yamada
3c5edd8ca5 ARM: omap: move OMAP specific code under arch/arm/
This patch moves OMAP specific directory entries
from the toplevel Makefile and spl/Makefile
to arch/arm/cpu/armv7/Makefile using Kbuild descending feature.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
2013-10-31 13:26:44 -04:00
Masahiro Yamada
37d82beb57 ARM: tegra: move Tegra specific code under arch/arm/
This patch moves Tegra specific directory entries
from the toplevel Makefile and spl/Makefile
to arch/arm/cpu/*/Makefile using Kbuild descending feature.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <TWarren@nvidia.com>
2013-10-31 13:26:44 -04:00
Marek Vasut
a0f9761075 ARM: mxs: Enable DCDC converter for battery boot
In case the board detected sufficient voltage for battery boot,
make sure the DCDC converter is ON and the board is not running
only from linregs, otherwise an instability will be observed.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2013-10-31 17:54:23 +01:00
Fabio Estevam
357efe69e9 mx5: lowlevel_init: Remove unused macro
setup_wdog macro is not used anywhere, so just remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-10-31 17:54:03 +01:00
Fabio Estevam
4867b634b7 ARM: mx5: Enable L2 cache
Enable L2 cache for improving the system performance.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-10-31 17:54:03 +01:00
Masahiro Yamada
fa8f95084d ARM: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Masahiro Yamada
3d9c84737b arm720t: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Masahiro Yamada
833db7405a arm920t: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Masahiro Yamada
d8769c62c1 arm926ejs: convert makefiles to Kbuild style
Note1:
In arch/arm/cpu/arm926ejs/spear/Makefile
START := start.o
was changed
extra-$(CONFIG_SPL_BUILD) := start.o
because spear/start.o is only used for SPL.

Note2:
START := start.o
was missing from arch/arm/cpu/arm926ejs/mxs/Makefile.
This commit simply adds
extra-$(CONFIG_SPL_BUILD) := start.o

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Masahiro Yamada
4e1aa8437a armv7: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Tom Rini
748bde608a Merge branch 'master' of git://git.denx.de/u-boot-usb 2013-10-21 08:10:36 -04:00
Dan Murphy
834e91af43 usb: dra7xx: Add support for dra7xx xhci USB host
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Dan Murphy
d861a333da ARM: OMAP5: Add registers and defines for USBOTG SS
Add the prcm registers and the bit definitions to enable the
USB SS port of the OMAP5 device.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:39 +02:00
Vivek Gautam
80c4c5964f arm: exynos: Add methods to control power to USB 3.0 PHY
Adding methods to turn on/off power to USB3.0 type PHY
as and when required by the controller.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
2013-10-20 23:42:38 +02:00
Marek Vasut
77b0e2239a ARM: mxs: Setup stack in JTAG mode
In case the MX23/MX28 is switched into JTAG mode via the BootMode select
switches, the BootROM bypasses the CPU core registers initialization.
This in turn means that the Stack Pointer (SP) register is not set as
it is in every other mode of operation, but instead is only zeroed out.

To prevent U-Boot SPL from crashing in this obscure JTAG mode, configure
the SP to point at the CONFIG_SYS_INIT_SP_ADDR if the SP is zeroed out.

Note that in case the SP is already configured, we must preserve that exact
SP value and must not modify it. This is important since in every other mode
but the JTAG mode, the SPL returns into the BootROM and BootROM in turn loads
U-Boot itself. If the SP were to be corrupted, the BootROM won't be able to
continue it's operation after returned from SPL and the system would crash.

Finally, add the JTAG mode switch identifier, so it's not recognised as
Unknown mode.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
2013-10-17 09:44:20 +02:00
Marek Vasut
6654f33c9b ARM: mxs: tools: Use mkimage for BootStream generation
Now that mkimage can generate an BootStream for i.MX23 and i.MX28,
use the mkimage as a default tool to generate the BootStreams instead
of the elftosb tool. This cuts out another obscure dependency.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-10-17 09:44:20 +02:00
Pierre Aubert
762a88ccf8 mx6: compute PLL PFD frequencies rather than using defines
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
2013-10-17 09:44:20 +02:00
Michal Simek
262f08d6ea zynq: Use arch_cpu_init() instead of lowlevel_init()
Zynq lowlevel_init() was implemented in C but stack
pointer is setup after function call in _main().
Move architecture setup to arch_cpu_init() which is call
as the first function in board_init_f() which
already have correct stack pointer.

Reported-by: Sven Schwermer <sven.schwermer@tuhh.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-10-17 08:34:45 +02:00
trem
fac9640895 i2c: mxc: move to new subsystem
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
2013-10-17 07:20:24 +02:00
Wolfgang Denk
16641d52fc Coding Style cleanup: drop some excessive empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:54 -04:00
Wolfgang Denk
d4c8aa9cb4 Coding Style cleanup: remove trailing empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:54 -04:00
Wolfgang Denk
93e1459641 Coding Style cleanup: replace leading SPACEs by TABs
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Drop changes for PEP 4 following python tools]
Signed-off-by: Tom Rini <trini@ti.com>
2013-10-14 16:06:54 -04:00
Wolfgang Denk
3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00
Dan Murphy
47a4bea6af ARM: omap4: Update sdram setting for panda rev A6
OMAP4 panda rev A6 is a 4430 es2.3 IC with an updated memory
part.

The panda rev A6 uses Elpida 2x4Gb memory and no longer uses Micron
so the timings needs to be updated

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-14 16:06:52 -04:00
Tom Rini
9f3fe6da27 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-10-08 09:51:48 -04:00
Tom Rini
968294bd7b Merge branch 'master' of git://git.denx.de/u-boot-spi 2013-10-08 09:03:15 -04:00
Chin Liang See
5d649d2b08 socfpga: Adding System Manager driver
Adding System Manager driver which will configure the
pin mux for real hardware Cyclone V development kit
(not Virtual Platform)

Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2013-10-07 19:32:21 +02:00
Albert ARIBAUD
0610a16cf2 omap1510inn: arm925t: remove support
omap1510inn is orphan and has been for years now.
Reove it and, as it was the only arm925t target,
also remove arm925t support.
Update doc/README.scrapyard accordingly.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-10-07 19:25:19 +02:00
Poddar, Sourav
62d206dc31 armv7: hw_data: change clock divider setting.
Clock requirement for qspi clk is 192 Mhz.
According to the below formulae,

f dpll = f ref * 2 * m /(n + 1)
clockoutx2_Hmn = f dpll / (hmn+ 1)

fref = 20 Mhz, m = 96, n = 4 gives f dpll = 768 Mhz
For clockoutx2_Hmn to be 768, hmn + 1 should be 4.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-07 17:55:51 +05:30
Matt Porter
c97a9b3275 omap5: add qspi support
Add QSPI definitions and clock configuration support.

Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-07 17:55:50 +05:30
Andre Przywara
f833e790b4 ARM: virtualization: replace verbose license with SPDX identifier
The original creation of arch/arm/cpu/armv7/{virt-v7.c,nonsec_virt.S}
predates the SPDX conversion, so the original elaborate license
statements sneaked in.
Fix this by replacing them with the proper abbreviation.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-07 08:21:13 -04:00
Tom Rini
f835c77fb7 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-10-04 13:17:48 -04:00
Andre Przywara
d429688754 ARM: extend non-secure switch to also go into HYP mode
For the KVM and XEN hypervisors to be usable, we need to enter the
kernel in HYP mode. Now that we already are in non-secure state,
HYP mode switching is within short reach.

While doing the non-secure switch, we have to enable the HVC
instruction and setup the HYP mode HVBAR (while still secure).

The actual switch is done by dropping back from a HYP mode handler
without actually leaving HYP mode, so we introduce a new handler
routine in our new secure exception vector table.

In the assembly switching routine we save and restore the banked LR
and SP registers around the hypercall to do the actual HYP mode
switch.

The C routine first checks whether we are in HYP mode already and
also whether the virtualization extensions are available. It also
checks whether the HYP mode switch was finally successful.
The bootm command part only calls the new function after the
non-secure switch.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-03 21:28:55 +02:00
Andre Przywara
ba6a169811 ARM: add SMP support for non-secure switch
Currently the non-secure switch is only done for the boot processor.
To enable full SMP support, we have to switch all secondary cores
into non-secure state also.

So we add an entry point for secondary CPUs coming out of low-power
state and make sure we put them into WFI again after having switched
to non-secure state.
For this we acknowledge and EOI the wake-up IPI, then go into WFI.
Once being kicked out of it later, we sanity check that the start
address has actually been changed (since another attempt to switch
to non-secure would block the core) and jump to the new address.

The actual CPU kick is done by sending an inter-processor interrupt
via the GIC to all CPU interfaces except the requesting processor.
The secondary cores will then setup their respective GIC CPU
interface.
While this approach is pretty universal across several ARMv7 boards,
we make this function weak in case someone needs to tweak this for
a specific board.

The way of setting the secondary's start address is board specific,
but mostly different only in the actual SMP pen address, so we also
provide a weak default implementation and just depend on the proper
address to be set in the config file.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-03 21:28:51 +02:00
Andre Przywara
1ef923851a ARM: add C function to switch to non-secure state
The core specific part of the work is done in the assembly routine
in nonsec_virt.S, introduced with the previous patch, but for the full
glory we need to setup the GIC distributor interface once for the
whole system, which is done in C here.
The routine is placed in arch/arm/cpu/armv7 to allow easy access from
other ARMv7 boards.

We check the availability of the security extensions first.

Since we need a safe way to access the GIC, we use the PERIPHBASE
registers on Cortex-A15 and A7 CPUs and do some sanity checks.
Boards not implementing the CBAR can override this value via a
configuration file variable.

Then we actually do the GIC enablement:
a) enable the GIC distributor, both for non-secure and secure state
   (GICD_CTLR[1:0] = 11b)
b) allow all interrupts to be handled from non-secure state
   (GICD_IGROUPRn = 0xFFFFFFFF)

The core specific GIC setup is then done in the assembly routine.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-03 21:28:43 +02:00
Andre Przywara
16212b594f ARM: add assembly routine to switch to non-secure state
While actually switching to non-secure state is one thing, another
part of this process is to make sure that we still have full access
to the interrupt controller (GIC).
The GIC is fully aware of secure vs. non-secure state, some
registers are banked, others may be configured to be accessible from
secure state only.
To be as generic as possible, we get the GIC memory mapped address
based on the PERIPHBASE value in the CBAR register. Since this
register is not architecturally defined, we check the MIDR before to
be from an A15 or A7.
For CPUs not having the CBAR or boards with wrong information herein
we allow providing the base address as a configuration variable.

Now that we know the GIC address, we:
a) allow private interrupts to be delivered to the core
   (GICD_IGROUPR0 = 0xFFFFFFFF)
b) enable the CPU interface (GICC_CTLR[0] = 1)
c) set the priority filter to allow non-secure interrupts
   (GICC_PMR = 0xFF)

Also we allow access to all coprocessor interfaces from non-secure
state by writing the appropriate bits in the NSACR register.

The generic timer base frequency register is only accessible from
secure state, so we have to program it now. Actually this should be
done from primary firmware before, but some boards seems to omit
this, so if needed we do this here with a board specific value.
The Versatile Express board does not need this, so we remove the
frequency from the configuration file here.

After having switched to non-secure state, we also enable the
non-secure GIC CPU interface, since this register is banked.

Since we need to call this routine also directly from the smp_pen
later (where we don't have any stack), we can only use caller saved
registers r0-r3 and r12 to not mess with the compiler.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-03 21:28:25 +02:00
Andre Przywara
45b940d6f9 ARM: add secure monitor handler to switch to non-secure state
A prerequisite for using virtualization is to be in HYP mode, which
requires the CPU to be in non-secure state first.
Add a new file in arch/arm/cpu/armv7 to hold a monitor handler routine
which switches the CPU to non-secure state by setting the NS and
associated bits.
According to the ARM architecture reference manual this should not be
done in SVC mode, so we have to setup a SMC handler for this.
We create a new vector table to avoid interference with other boards.
The MVBAR register will be programmed later just before the smc call.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-03 21:27:11 +02:00
Tom Rini
6297872cd5 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-10-02 11:45:22 -04:00
Albert ARIBAUD
f04c537629 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-10-02 14:53:27 +02:00
Albert ARIBAUD
5c8d5b6fc1 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-10-02 08:10:36 +02:00
Pierre Aubert
a0a0dacfe8 mx6: Fix use of improper value in enable_ipu_clock
The value MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET that was used to initialize
the CCGR3 register caused an undefined value for CG0.

Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-09-27 13:53:35 +02:00
Bo Shen
3668ce3c80 ARM: atmel: add RNDIS gadget support
Add RNDIS gadget support to test atmel usba udc driver

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-09-24 17:51:35 +02:00
Dani Krishna Mohan
3dd22a37aa ARM: Added I2S0 clocks for audio
This patch makes the necessary changes for making use of
I2S0 channel instead of I2S1 channel on smdk board. This
changes are done to maintain the uniformity to use I2S0 channel.

Signed-off-by: Dani Krishna Mohan <krishna.md@samsung.com>
2013-09-24 09:10:33 -04:00
Jeroen Hofstee
fe1378a961 ARM: use r9 for gd
To be more EABI compliant and as a preparation for building
with clang, use the platform-specific r9 register for gd
instead of r8.

note: The FIQ is not updated since it is not used in u-boot,
and under discussion for the time being.

The following checkpatch warning is ignored:
WARNING: Use of volatile is usually wrong: see
Documentation/volatile-considered-harmful.txt

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-09-23 18:00:02 +02:00
Masahiro Yamada
3102274d8b ARM: refactor compiler options in config.mk
Every ARM cpu config.mk (arch/arm/cpu/{CPUDIR}/config.mk) defines:

PLATFORM_RELFLAGS += -fno-common -ffixed-r8 -msoft-float

So, this patch moves the common compiler options to arch/arm/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-09-23 17:03:05 +02:00
Michal Simek
7ba69b7dcc arm: zynq: Fix timer loadaddress
Reload address was written to the counter register
instead of load register.
The problem happens when timer expires but never
reload to ~0UL (it is downcount timer).

Reported-by: Stephen MacMahon <stephenm@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-09-23 16:26:32 +02:00
Lokesh Vutla
e22cc0cf13 ARM: OMAP5: Avoid writing into LDO SRAM bits
Writing magic bits into LDO SRAM was suggested only for OMAP5432
ES1.0. Now these are no longer applicable. Moreover these bits should
not be overwritten as they are loaded from EFUSE. So avoid
writing into these registers.

Boot tested on OMAP5432 ES2.0

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-09-20 16:57:40 -04:00
Steve Kipisz
52f7d8442e am335x:Handle worst case scenario for Errata 1.0.24
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset,
the boot ROM sets the frequencies for OPP100. This patch attempts to
drop the frequencies back to OPP50 as soon as possible in the SPL. Then
later the voltages and frequencies up set higher.

Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Adapt to current framework]
Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 16:57:40 -04:00
Tom Rini
9721027aae am335x_evm: am33xx_spl_board_init function and scale core frequency
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on.  In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed.  In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz.  In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1.  As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe.  In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.

Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 16:57:35 -04:00
Fabio Estevam
31f07964c8 mx6slevk: Add Ethernet support
mx6slevk has a SMSC8720 connected in RMII mode.

Add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20 17:55:37 +02:00
Tom Rini
6a0d803c7c am33xx: Add am33xx_spl_board_init function, call
We need to allow for a further call-out in spl_board_init.  Call this
am33xx_spl_board_init and add a __weak version.  This function may be
used to scale the MPU frequency up, depending on board needs.

Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 11:01:26 -04:00
Robert P. J. Day
1bce2aeb6f Cosmetic: Fix a number of typos, no functional changes.
Fix various misspellings of things like "environment", "kernel",
"default" and "volatile", and throw in a couple grammar fixes.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-09-20 10:30:54 -04:00
Masahiro Yamada
aeef2b090d ARM: s3c44b0: remove remainders of dead board
Because commit 5dc5f36 removed B2 board support,
arch/arm/cpu/s3c44b0/* and arch/arm/include/asm/arch-s3c44b0/*
are not necessary anymore.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
2013-09-19 08:59:49 +02:00
trem
e24278aff2 mx27: add missing constant for mx27
Add some missing constant (chip select, ...)

Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-09-10 19:12:55 +02:00
Marek Vasut
7b8657e2bd ARM: mxs: Receive r0 and r1 passed from BootROM
Make sure value in register r0 and r1 is preserved and passed to
the board_init_ll() and mxs_common_spl_init() where it can be
processed further. The value in r0 can be configured during the
BootStream generation to arbitary value, r1 contains pointer to
return value from CALL'd function.

This patch also clears the value in r0 before returning to BootROM
to make sure the BootROM is not confused by this value.

Finally, this patch cleans up some comments in the start.S file.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-09-10 19:12:54 +02:00
Marek Vasut
d4c9135c96 ARM: mxs: Document the power block initialization
This patch adds documentation for the functions used during the
initialization of MXS power block.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-09-10 19:12:54 +02:00
Andrew Gabbasov
d55e0dabd7 mx6: Fix calculation of emi_slow clock rate
This is porting of Freescale's patch from version imx_v2009.08_3.0.35_4.0.0,
that fixes the obvious mistype of bits offset macro name (ACLK_EMI_PODF_OFFSET
was used instead of ACLK_EMI_SLOW_PODF_OFFSET).

Using the occasion, change the variable name 'emi_slow_pof' to more consistent
'emi_slow_podf'.

Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2013-09-10 18:22:27 +02:00
Chin Liang See
68e1747f9c socfpga: Creating driver for Reset Manager
Consolidating reset code into reset_manager.c. Also
separating reset configuration for virtual target and
real hardware Cyclone V development kit

Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2013-09-06 12:09:06 +02:00
Michal Simek
fba1ed422e arm: lds: Remove libgcc eabi exception handling tables
Remove ARM eabi exception handling tables (for frame unwinding).
AFAICT, u-boot stubs away the frame unwiding routines, so the tables will
more or less just consume space. It should be OK to remove them.

Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-09-05 13:41:42 +02:00
Albert ARIBAUD
19d829fa60 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Conflicts:
	drivers/serial/serial.c

The conflict above was a trivial case of adding one init
function in each branch, and manually resolved in merge.
2013-09-05 11:15:26 +02:00
Albert ARIBAUD
e62d5fb0da Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-09-04 14:06:56 +02:00
Albert ARIBAUD
4eef93da26 Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master' 2013-09-04 11:50:25 +02:00
Albert ARIBAUD
6d4511b2c6 Merge 'u-boot-microblaze/zynq' into (u-boot-arm/master'
Conflicts:
	arch/arm/include/asm/arch-zynq/hardware.h

The conflict above was trivial and solved during merge.
2013-09-03 14:01:02 +02:00
Eric Nelson
8467faef7f i.MX6: Set and clear the gating bits for Phase Fractional Dividers
This addresses silicon errata ERR006282 as described in this
document:
	https://community.freescale.com/docs/DOC-94581

Also implemented in Freescale's 2009.08-based release:

	http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/
	Commit id: b7c5badf94ffbe6cd0845efbb75e16e05e3af404

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-08-31 18:09:37 +02:00
Hector Palacios
6f6059e0f1 ARM: mxs: rename function that sets AUTO_RESTART flag
The AUTO_RESTART flag of HW_RTC_PERSISTENT0 register will
power up the chip automatically 180ms after power down.
This bit must be enabled by the boot loader to ensure the
target can start upon hardware reset or watchdog reset
even when powered from a battery.

Currently the function named 'mxs_power_clear_auto_restart()'
is setting this flag although the 'clear' in its name suggest
the opposite.

This patch renames the function to 'mxs_power_set_auto_restart()'
and removes the comment about EVK revision A which was confusing
because the function indeed was setting the flag.

Signed-off-by: Hector Palacios <hector.palacios@digi.com>
2013-08-31 17:50:38 +02:00
Marek Vasut
bce8837071 ARM: mxs: tools: Add mkimage support for MXS bootstream
Add mkimage support for generating and verifying MXS bootstream.
The implementation here is mostly a glue code between MXSSB v0.4
and mkimage, but the long-term goal is to rectify this and merge
MXSSB with mkimage more tightly. Once this code is properly in
U-Boot, MXSSB shall be deprecated in favor of mkimage-mxsimage
support.

Note that the mxsimage generator needs libcrypto from OpenSSL, I
therefore enabled the libcrypto/libssl unconditionally.

MXSSB: http://git.denx.de/?p=mxssb.git;a=summary

The code is based on research presented at:
http://www.rockbox.org/wiki/SbFileFormat

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
2013-08-31 15:26:52 +02:00
Stefano Babic
b83c709e8d imx: add status reporting for HAB status
Add functions to report the HAB (High Assurance Boot) status
of e.g. i.MX6 CPUs.

This is taken from

git://git.freescale.com/imx/uboot-imx.git branch imx_v2009.08_3.0.35_4.0.0
cpu/arm_cortexa8/mx6/generic.c
include/asm-arm/arch-mx6/mx6_secure.h

Signed-off-by: Stefano Babic <sbabic@denx.de>
2013-08-31 15:06:29 +02:00
Albert ARIBAUD
8d20836615 arm: omap3: fix SRAM copy and execution sequence
Fix size calculation in copy of go_to_speed into SRAM.
Use SRAM_CLK_CODE in call to SRAM-based go_to_speed.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-08-28 11:44:58 -04:00
Lubomir Popov
81aee9723d ARM: OMAP4470: Add Elpida EDB8164B3PF memory configuration
OMAP4470 SDP SoM has EDB8164B3PF PoP memory on board.
This memory has 4Gb x 2CS = 8Gb configuration.
Add configuration for runtime calculation and precalculated cases.

Patch is based on a draft Lubomir's patch [1].

[1] http://lists.denx.de/pipermail/u-boot/2013-April/150851.html

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
[taras@ti.com: cleaned up patch and fixed precalculated values]
Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28 11:44:58 -04:00
Taras Kondratiuk
40aadf9201 ARM: OMAP4470: Add voltage and dpll data
OMAP4470 reference design uses TWL6032 PMIC
with a following connection scheme:
  VDD_CORE = TWL6032 SMPS2
  VDD_MPU  = TWL6032 SMPS1
  VDD_IVA  = TWL6032 SMPS5

Set voltage and frequency values according to
OMAP4470 Data Manual Operating Condition Addendum v0.7

Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28 11:44:58 -04:00
Taras Kondratiuk
696f81f9a9 ARM: OMAP4470: Add OMAP4470 identification
Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28 11:44:58 -04:00
Fabio Estevam
76b6b19614 usb: ehci-mx5: Use 'bool' instead of 'unsigned char'
The 'enable' argument can be better expressed as boolean.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2013-08-26 21:56:34 +02:00
Bo Shen
e08d6f3aaf arm: atmel: add gmac support for sama5d3xek board
add gmac support for sama5d3xek board, the gmac embedded in:
  - sama5d33, sama5d34, sama5d35

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22 16:49:54 +02:00
Tom Rini
e20cc2ca15 Merge branch 'master' of git://88.191.163.10/u-boot-arm
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.

Conflicts:
	arch/arm/include/asm/arch-am33xx/hardware.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-18 14:14:34 -04:00
Albert ARIBAUD
9ed887caec Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-08-17 18:24:13 +02:00
TENART Antoine
dcf846d5da Add TI816X support
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Fix warnings about vtp things in emif4.c, adapt AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:37 -04:00
TENART Antoine
9ed6e41239 Prepare for TI816X : reuse existing code from TI814X
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX

Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:37 -04:00
Heiko Schocher
9c8deaeeb7 arm, da850: enable the correct uart in arch_cpu_init()
in arch_cpu_init() uart2 is fix enabled, without reference the
setting from CONFIG_SYS_NS16550_COM1. Use the setting from
CONFIG_SYS_NS16550_COM1 for enabling the console.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
2013-08-15 18:38:36 -04:00
Heiko Schocher
78056717e3 arm/davinci/da850: add uart0_pins_rtscts and RMII_MHz_50_CLK in emac_pins_rmii pinmux
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-08-15 18:38:36 -04:00
Taras Kondratiuk
0474fb0e2b omap: emif: Set initial DDR PHY config first
Commit "OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon"
(f40107345c)
changed sequence to set final DDR PHY config register value at the beginning.
Looks like it was made by mistake and should be reverted.

Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-15 18:38:35 -04:00
Masahiro Yamada
2f6af82719 ARM: omap24xx: remove remainders of dead board
Since Commit 7f5eef9 removed OMAP2420H4 support,
arm1136/omap24xx has not been used at all.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-15 18:38:33 -04:00
Naumann Andreas
a704a6d615 ARM: omap3: Implement dpll5 (HSUSB clk) workaround for OMAP36xx/AM/DM37xx according to errata sprz318e.
In chapter 'Advisory 2.1 USB Host Clock Drift Causes USB Spec Non-compliance in Certain Configurations' of the TI Errata it is recommended to use certain div/mult values for the DPLL5 clock setup.
So far u-boot used the old 34xx values, so I added the errata recommended values specificly for 36xx init only.
Also, the FSEL registers exist no longer, so removed them from init.

Tested this on a AM3703 board with 19.2MHz oscillator, which previously couldnt lock the dpll5 (kernel complained). As a consequence the EHCI USB port wasnt usable in U-Boot and kernel. With this patch, kernel panics disappear and USB working fine in u-boot and kernel.

Signed-off-by: Andreas Naumann <anaumann@ultratronik.de>
[trini: Add extern to <asm/arch-omap3/clock.h>
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 09:09:29 -04:00
Lokesh Vutla
571804086f ARM: AM43xx: Add build support
Add AM43xx support in the required places

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
806d279247 ARM: OMAP: Add CONFIG_OMAP_COMMON
Adding a new CONFIG_OMAP_COMMON which is included by all boards
that needs to build cpu/armv7/omap-common folder.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
3b34ac13fe ARM: AM43xx: clocks: Add dpll and clock data
Add dpll and clock data for AM43xx

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Heiko Schocher
0660481a59 ARM: AM33xx: Move s_init to a common place
s_init has the same outline for all the AM33xx based
board. So making it generic.
This also helps in addition of new Soc with minimal changes.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
95cb69faeb ARM: AM33xx: Cleanup clocks layer
Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
94d77fb656 ARM: AM33xx: Cleanup dplls data
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.

This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00