The EFI memory init uses gd->ram_top for conventional memory. In
current implementation, the ram_top is below optee address. This cause
grub failed to allocation memory for initrd.
The change updates DDR bank setup functions to place the u-boot at top
DDR in 4GB space.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Need to drop phy-reset-gpios before booting linux, this property
is legacy property and replaced with reset-gpios.
If provide both, kernel would failed to request the same gpio twice
and cause fec not work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The extcon is an decrepted property and not used by upstream Linux and
NXP 5.10 kernel, so we remove it before kicking linux in case it is in
dts. Otherwise distro kernel will not able to have usb function.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beside the fused modules on iMX8MP Lite, this part has also fused
GPU3D/2D, LVDS and MIPI DSI.
So we have to disable them for kernel and also disable MIPI DSI
in u-boot DTS for splash screen at runtime.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wait 1ms before issuing the first MRS command to write DDR3 Mode
registers.
There is a requirement to wait a minimum time before issuing command to
the DDR3 device, according to the JEDEC standard this time is 500us
(after RESET_n is de-asserted until CKE becomes active) + tXPR (Reset
CKE Exit time, maximum value 360ns).
It seems that for some reason this is not enforced by the MMDC
controller.
Without this change we experienced random memory initialization failures
with about 2% boot failure rate on specific problematic boards, after
this change we were able to do more than 10.000 power-cycle without a
single failure.
Fixes: fe0f7f7842 ("mx6: add mmdc configuration for MX6Q/MX6DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The current DDR write level calibration routine always overwrite
the ralat/walat fields to their maximum value, just save
the existing values at the beginning of the calibration routine
and restore it at the end.
In case the delay is estimated by the user to be more than one cycle the
walat should be configured according to that, this is not
automatically done. From the i.MX6 RM:
The user should read the results of the associated delay-line at
MPWLDECTRL#[WL_DL_ABS_OFFSET#] and in case the user estimates that the
reasonable delay may be above 1 cycle then the user should indicate it at
MPWLDECTRL#[WL_CYC_DEL#]. Moreover the user should indicate it in
MDMISC[WALAT] field. For example, if the result of the write leveling calibration
is 100/256 parts of a cycle, but the user estimates that the delay is above 2 cycles
then MPWLDECTRL#[WL_CYC_DEL#] should be configured to 2, so the total
delay will be 2 and 100/256 parts of a cycle
Probably it would just possible to not overwrite the mdmisc register in
the first place, since this is not present in the write_level_calib() example
in NXP AN4467 nor in the i.MX6 RM (44.11.6.1 Hardware Write Leveling
Calibration).
Fixes: d339f16911 ("arm: imx6: Add DDR3 calibration code for MX6 Q/D/DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable multiple storages for u-boot env:
MMC or SPI flash or NOWHERE for usb
so u-boot can runtime select the storage flash according to boot device.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The TEE memory should be reserved when TEE is present, so need
to runtime update dram bank and memory information according to
tee present or not.
Signed-off-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable wdog_ad interrupt being triggered by CMC1 to CM33 to let CM33
know A35 reset and reinitialize rpmsg.
Clear wdog_ad and AD_PERIPH reset interrupt after A35 up, otherwise
M33 will always receive interrupt.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Assign the LPAV owner to RTD, and assign LPAV masters and peripherals
to APD. So except the masters and peripherals, other resources
(like DDR, cgc2, pcc5) in LPAV won't be reset during reboot and suspend.
No needs to initialize DDR again after reboot.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable MU0_B clk by default. When M33 image is loaded by Jlink,
the previous method not enable MU0_B clk and not able to communicate
with M33, so let's enable it by default.
And we not put it under kernel dts, because it conflicts with i.MX8QM
suspend/resume logic which requires large change.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When reset with dual boot mode, the LPAV domain won't power down
due to its master is not assigned to APD. So the NICLPAV keeps the
last setting to use PLL4PFD1. So before SPL initialize the PLL4,
we need to switch NICLPAV to FRO192, otherwise system will hang.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When M33 is LPAV owner in dual boot, DDR, PCC5, CGC2 won't be reset
during APD reset. So no need to init DDR again after reboot, but need to
reconfigure the PLL4 PFD/PFDDIV/LPAV NIC etc, because kernel may
change or disable some of them.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new ddr script, defconfig for ND
Configure the clock for ND mode
changing A35 to 960MHz for OD mode
Update NIC CLK for the various modes
Introduce clock_init_early/late, late is used after pmic voltage
setting, early is used in the very early stage for upower mu, lpuart and
etc.
Note: NIC runs at 324MHz, 442MHz has some random kernel hang issue with
cpuidle enabled now.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add i3c controller clock enable/disable function for imx8ulp.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add functions to check if M33 image is booted and handshake with M33
image via MU. A core notifies M33 to start init by FCR F0, then wait
M33 init done signal by checking FSR F0.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some printf() have strings that doesn't terminate with end of line
and make the output hard to read.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Disable SPL exception vector which causes issue to ROM patch execution
when SPL calling ROM API.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add settings for operating PLL at 933 MHz. This setting is useful in
case the LPDDR4 DRAM should operate at 1866 MHz or 3733 MT/s.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
added crypto node in device tree.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX7D - added support for JR driver model.
removed sec_init() call, sec is initialized based on
job ring information processed from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX6,i.MX6SX,i.MX6UL - added support for JR driver model.
removed sec_init() call, sec is initialized based on
job ring information processed from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX8MM/MN/MP/MQ - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Platforms can overwrite the weak definition of spl_mmc_boot_mode() to
determine where to load U-Boot proper from.
For most of them this is a trivial decision based on Kconfig variables,
but it might be desirable the probe the actual device to answer this
question.
Pass the pointer to the mmc struct to that function, so implementations
can make use of that.
Compile-tested for all users changed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ley Foon Tan <ley.foon.tan@inte.com> (for SoCFPGA)
Acked-by: Lokesh Vutla <lokeshvutla@ti.com> (for OMAP and K3)
Reviewed-by: Simon Glass <sjg@chromium.org>
To avoid passing around an extra register everywhere, save esr in
pt_regs like the rest. For proper alignment we need to have a second
(unused) register. All the printfs have to be adjusted, since
it's now an unsigned long and not an int.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is used in nxp u-boot tree.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The interface for NOR/OneNAND is called "EIM" not "EMI". Fix this.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The previous code wrote the contents of the fuse as is in the
REFTOP_VBGADJ[2:0], but this was wrong if you consider the contents of
the table in the code comment. This table is also different from the
table in the commit description. But then, which of the two is correct?
If it is assumed that an unprogrammed fuse has a value of 0 then for
backward compatibility of the code REFTOP_VBGADJ[2:0] must be set to
6 (b'110). Therefore, the table in the code comment can be considered
correct as well as this patch.
Fixes: 97c16dc8bf ("imx: mx6ull: update the REFTOP_VBGADJ setting")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add PLL 1.4 GHz, 1.5 GHz, 1.6 GHz, 1.8 GHz options for iMX8M SoCs
in case they should be operated faster, e.g. to improve boot time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Linux uses slightly different divider settings for the 1.2 GHz PLL
configuration, adjust the coefficients to match Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
According to TRM for i.MX8M Nano and Plus, GPR10 register contains lock
bit for TZASC_ID_SWAP_BYPASS bit. This bit is required to be set in
order to avoid AXI bus errors when GPU is enabled on the platform.
TZASC_ID_SWAP_BYPASS bit is alread set for all imx8m applicable
derivatives, but is missing a lock settings to be applied.
Set the TZASC_ID_SWAP_BYPASS_LOCK bit for those derivatives which have
it implemented.
Since we're here, provide also names to bits from TRM instead of using
BIT() macro in the code.
Fixes: deca6cfbf5 ("imx8mn: set BYPASS ID SWAP to avoid AXI bus errors")
Fixes: a07c718129 ("imx8mp: set BYPASS ID SWAP to avoid AXI bus errors")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Add support of secondary boot address for imx8mn. The secondary
boot address is hardcoded in the fuse. The value is calculated
from there according to the following description:
The fuse IMG_CNTN_SET1_OFFSET (0x490[22:19]) is defined as follows:
- Secondary boot is disabled if fuse value is bigger than 10, n = fuse
value bigger than 10.
- n == 0: Offset = 4MB
- n == 2: Offset = 1MB
- Others & n <= 10 : Offset = 1MB*2^n
- For FlexSPI boot, the valid values are: 0, 1, 2, 3, 4, 5, 6, and 7.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Similar to what has been done before with c5437e5b for u-boot proper, we
enable the SMP bit for SPL as well. This is necessary when SDP booting
straight into Linux, i.e. falcon boot. When SDP boot mode is active, the
ROM code does not set this bit which makes the caches not work once
activated in Linux.
On an i.MX6ULL (528MHz), this reduces a minimal kernel's boot time into
an initramfs shell from ~6.1s down to ~1.2s.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Use imx6_src_get_boot_mode() instead of manually reading SBMR1. The
existing function has proper handling for software overrides of the
bootdevice which can happen, for example, when booting from an alternate
source using `bmode`.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Extension boards can be added to Compulab's iot-gate-imx8mm.
We implement extension board manager for detecting the extension
boards.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: uboot-imx <uboot-imx@nxp.com>
Obatin the SoC current temperature in print_cpuinfo().
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The DDRLOCKED bit in CGC2 DDRCLK will auto lock up and down by HW
according to DDR DIV updating or DDR CLK halt status change. So DDR
PCC disable/enable will trigger the lock up/down flow. We
need wait until unlock to ensure clock is ready.
And before configuring the DDRCLK DIV, we need polling the DDRLOCKED
until it is unlocked. Otherwise writing ti DIV bits will not set.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch implements enable_adc1_clk() to enable or disable the ADC1
clock on i.MX8ULP.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Get the MAC address from fuse bank5 word 3 and 4. It has
MSB first at lowest address, so have a reverse order with other
iMX used in mac.c
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When LPAV is allocated to RTD, the LPAV won't be reset. So we have to
reset DCNano and MIPI DSI in u-boot before enabling the drivers
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The LPAV is not allocated to APD when dual boot, so LPAV won't
reset when APD is reset. We have to explicitly reset the DDR,
otherwise its initialization will fail.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0
LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision.
A0.2 will fix the issue in ROM. But A0.1 we have to workaround
it in SPL by setting LPOSCCTRL BIASCURRENT again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the freescale vendor name from CPU revision print to align
with other i.MX platforms
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The setting does not have effect because we should set it after
power on the PS16 for NIC AV.
So move it after upower_init which has powered on all PS
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To avoid DCNANO underrun issue on high loading test, set its
read Qos on NIC_LPAV to highest
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board use IO9 of PCA6416 on LPI2C0 and TPM0 for MIPI DSI MUX and
backlight. However the LPI2C0 and TPM0 are M33 resources, in this
patch we simply access them, but this is a temporary solution.
We will modify it when M33 FW changes to set MIPI DSI panel as default
path and enable backlight after reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the DSI clock enable and disable with PCC reset used.
Add the LCD pixel clock calculation and configuration for DCNano
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Assign the PXP/HIFI4/EPDC to APD domain, otherwise APD not
able to receive interrupts from the modules.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When single boot, assign AP domain as the master domain of the LPAV.
Allocates LPAV master and slave resources like GPU, DCNano, MIPI-DSI
eDMA channel and eDMA request to APD
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
S400 enables RDC only when the DBD_EN is fused. Otherwise, the RDC
is allowed by all masters.
Current S400 has issue if the XRDC has released to A35, then A35 reset
will fail in ROM due to S400 fails to get XRDC.
So temp work around is checking the DBD_EN, if it is not fused, we
don't need to call release XRDC or TRDC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change boot device logic to also allow environment stored in fat and in
ext4 when booting from SD or from eMMC.
As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at env_get_location
to use IS_ENABLED instead for all modes, returning NOWHERE when no valid
mode is found.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Correct printf format for unsigned long long is %llx and not %llxx.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Force selecting features present in SoC i.MX7ULP.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Return the root clock values for MXC_CSPI_CLK, MXC_I2C_CLK,
MXC_UART_CLK and MXC_QSPI_CLK.
At least for the I2C clock the missing support leads to a wrong
configured I2C frequency. The expected value is 100kHz but the resulting
value is about 1MHz.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
All i.MX8MQ boards have been converted to binman, which makes it
necessary to flash both flash.bin and u-boot.itb to get a bootable
system. Prior to the conversion, only flash.bin was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single bootable
binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone (for
example, for secure boot purposes).
Also update imx8mq_evk.rst to remove the u-boot.itb copy step.
This is a cherry-pick of 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") adjusted to apply to i.MX8MQ.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
CMD_DM is useful for showing the whole DM tree.
Enable it via "imply CMD_DM".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Use binman to pack images.
Note that imx8mm_venice supports several boards via multiple DTB's thus
in the fit node we must use:
- fit,fdt-list = "of-list"
- fdt-SEQ
- config-SEQ
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
After all these board switch to binman, we could use common imximage.cfg
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Somewhere along the line, the board stopped being able to boot.
Rather than just fixing the issue, let's fix the issue and migrate
to binman to eliminate a warning when using custom imx tools for
generating the binary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
To eliminate a warning when using custom imx tools for generating
a binary, use binman to generate flash.bin.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The subdivision name "TQ Components" hasn't been in use for a long time.
Rename the vendor directory to "tq", which also matches our Device Tree
vendor prefix.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Get Unique ID of SoC iMX7ULP, using the logic described in Fusemap
(IMX7ULPRMB2_Rev0_Fusemap) attached in the i.MX 7ULP APRM [1].
[1]
https://www.nxp.com/docs/en/reference-manual/IMX7ULPRMB2.pdf
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
i.MX8MP has two ENET controllers, have to update the function to
enable loading two MAC addresses.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Make use of the host Kconfig for FIT. With this we can use
CONFIG_IS_ENABLED(FIT) directly in the host build, so drop the unnecessary
indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
After switch to use binman, no need to use the bash script
to check file exsiting or not. And there is bug that
the script will be executed everytime Makefile is used which is
confusing people.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Update the mx7ulp wdog disable sequence to avoid potential reset
issue in unlock or refresh sequence. Both sequence need two words
write to wdog CNT register in 16 bus clocks window, if miss the
window, the write will cause violation in wdog and reset the chip.
Current u-boot code is using writel() function which has a DMB
barrier to order the memory access. The DMB between two words write
may introduce some delay in certain circumstance, causing the wdog
reset due to 16 bus clock window requirement.
Also, WDOG1 might have been enabled already depending on FUSE hence
we need to be as close as possible to its reconfiguration timing
requirement of 128 bus clock limit.
This patch replaces writel() function by __raw_writel() to avoid such
issue, and improve to check if watchdog is already disabled or
unlocked.
Signed-off-by: Ye Li <ye.li@nxp.com>
Co-developed-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Co-developed-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Since derivatives are moving to binman from usage of the FIT generator
script, and considering the warning introduced in f4a43d2925
("Makefile: Warn against using CONFIG_SPL_FIT_GENERATOR"), usage of FIT
generator is discouraged.
Current FIT generator also generates broken output, since commit
3f04db891a ("image: Check for unit addresses in FITs") prohibits using
'@' for unit addresses but the generator script still emits the old
sematics.
Remove the generator script and corresponding call in Makefile, all
derivatives should be migrated to binman in order to provide binary
images.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently imx8mm-cl-iot-gate_defconfig fails to produce a working boot
binary due to the lack of fip.bin:
" BINMAN all
Image 'main-section' is missing external blobs and is non-functional: blob-ext
Some images are invalid"
To make the build process more consistent with the other i.MX8M targets,
split the defconfig in two:
- imx8mm-cl-iot-gate_defconfig: standard defconfig that only
requires ATF / DDR firmware.
- imx8mm-cl-iot-gate-optee_defconfig: "more advanced" defconfig that
requires ATF / Optee / mbedtls / DDR firmware.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
When TEE is loaded, we need to restrict the memory usage based
on rom_pointer[0]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
cherry-picked from NXP code:
719d665a87c6: ("MLK-20467 imx8m: Fix issue for booting signed image through uuu")
which fixes secure boot on imx8m based boards. Problem was
that FIT header and so IVT header too, was loaded to
memallocated address. So the ivt header address coded
in IVT itself does not fit with the real position.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com>
read the address where the IVT header must sit
from IVT image header, loaded from SPL into
an malloced buffer and copy the IVT header
to this address
May make this dependend on SoC ?
Signed-off-by: Heiko Schocher <hs@denx.de>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This config is only used by three boards with this SOC. Most other
platforms derive this information from devicetree, and are unlikely
to ever need this config.
Moreover, it is confusing when Kconfig asks for this value under
"Support OPTEE images", but does not do anything with the value.
Move it to imx7 for those boards who still make use of it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This function is clearly architecture specific code, not board specific
code. The only difference from the previous arm arch_lmb_reserve() is the
extra reservation of 16k of memory below the stack bottom, rather than
the 4k. The common code now also uses 16k alignment. Remove this custom
implementation, as it now behaves exactly as the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ye Li <ye.li@nxp.com>
No iMX platforms have supported ATAG-based booting. They have however
re-used the CONFIG_SERIAL_TAG option as a way to enable support of
reading the OTP fuses and setting the serial# environment variable in
some cases. Change the warp7 support to use this symbol, use this for
updating the rest of the imx7 code, and update the imx8 conditionals.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Provide a default Kconfig value of the default script
- Largely continue to define this via the board Kconfig file
- For the boards that select a script based on defconfig rather than
TARGET, keep this within the defconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, there is no over-arching symbol for access to
arch/arm/mach-imx nor the CONFIG symbols that are common over all of
these related platforms. This new CONFIG symbol will allow us to start
down this path.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When booting from boot part1/2, the image offset should be 0, but
ROM has a bug to return 0x8000. Has to workaround the issue before
ROM fix it.
Use a ROM function to know boot from emmc boot part or user part
So we can set the image offset accordingly.
Signed-off-by: Ye Li <ye.li@nxp.com>
Since CMC1 MR0 only reflects high 16 bits boot cfg used for AP domian,
it does not connect to low 16 bits for RTD. So we can't get the correct
boot mode.
Change to use DGO_GP5 of SEC_SIM which is set by ROM.
Signed-off-by: Ye Li <ye.li@nxp.com>
The CMC1 SRS reflects the current reset cause, not SSRS.
Then you could get "Reset cause: WARM-WDG" when issue reset in U-Boot.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Need probe the S400 MU device in arch_cpu_init_dm, so we can use
S400 API in u-boot
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Rlease LPAV from RTD to APD
Release gpu2D/3D to APD
Set TRDC MBC2 MEM1 for iomuxc0 access
Since upower depends AP/M33 SW to configure IOMUX for its PMIC i2c
and MODE pins. we have to open iomuxc0 access for A35 core (domain 7)
in single boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
There is xrdc inside i.MX8ULP, we need to configure permission to make
sure AP non-secure world could access the resources.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since S400 will set the memory of SPL image to R/X. We can't write
to any data in SPL image.
1. Set the parameters save/restore only for u-boot, not for SPL. to
avoid write data.
2. Not use MU DM driver but directly call MU API to send release XRDC
to S400 at early phase.
3. Configure the SPL image memory of SRAM2 to writable (R/W/X)
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because we have set reset vector to ATF in SPL, have to set it back
to ROM for any reset in u-boot
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SRAM2 is half L2 cache and default to SRAM after system boot.
To enable the full l2 cache (512KB), it needs to reset A35 to make
the change happen.
So re-implement the jump entry function in SPL:
1. configure the core0 reset vector to entry (ATF)
2. enable the L2 full cache
3. reset A35
So when core0 up, it runs into ATF. And we have 512KB L2 cache working.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8ULP support using ROM API to load container image,
it use same ROM API as i.MX8MN/MP, and use same container format
as i.MX8QM/QXP.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since the container is shared among i.MX platforms, move its header file
to mach-imx
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add basic i.MX8ULP support
For the MMU part, Using a simple way the calculate the MMU size to avoid
default heavy calcaulation. And align address and size in the table
settings to 2MB or 4GB as much as possible. So we can reduce the 4K page
allocations in MMU table which will spends much time in create the
page table
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
As the deadline for migration to DM_USB, when using a USB host
controller has now gone two years past the deadline, enforce migration.
This is done by:
- Ensuring that all host controller options (other than the very legacy
old MUSB ones) now select USB_HOST. USB_HOST now enforces DM_USB and
OF_CONTROL.
- Remove other parts of Kconfig logic that had platforms pick DM_USB.
- To keep Kconfig happy, have some select statements test for USB_HOST
as well.
- Re-order some Kconfig entries and menus so that we can cleanly pick
host or gadget roles. For the various HCD options that have platform
glue options, group them together and update dependencies in some
cases.
- As SPL_DM_USB is not required, on platforms that had not yet enabled
it, disable it.
Cc: Marek Vasut <marex@denx.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Samuel Holland <samuel@sholland.org>
Cc: FUKAUMI Naoki <naobsd@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add clock function to setup relevant clocks for USB3.0 controllers and
PHYs on i.MX8MQ
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
In case the iMX8M boot from eMMC boot partition and the primary image
is corrupted, the BootROM is capable of starting a secondary image in
the other eMMC boot partition as a fallback.
However, the BootROM leaves the eMMC BOOT_PARTITION_ENABLE setting as
it was, i.e. pointing to the boot partition containing the corrupted
image, and the BootROM does not provide any indication that this sort
of fallback occured.
According to AN12853 i.MX ROMs Log Events, Rev. 0, May 2020, it is
possible to determine whether fallback event occurred by parsing the
ROM event log. In case ROM event ID 0x51 is present, fallback event
did occur.
This patch implements ROM event log parsing and search for event ID
0x51 for all iMX8M SoCs, and based on that corrects the eMMC boot
partition selection. This way, the SPL loads the remaining boot
components from the same eMMC boot partition from which it was
started, even in case of the fallback.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Harald Seiler <hws@denx.de>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Make macros actually use passed parameter instead of local variables
that happen
to be named the same as symbols in macro expansion.
Signed-off-by: Kacper Kubkowski <kkubkowski@fluence.pl>
Some IPs have their accessible address space restricted by the
interconnect. Let's make sure U-Boot only ever uses the space below
the 4G address boundary (which is 3GiB big), even when the effective
available memory is bigger.
We implement board_get_usable_ram_top() for all i.MX8M SoCs, as the
whole family is affected by this.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
macro, which expands the value provided to the Hz range without taking into
account the precise Hz setting. This causes the frequency of 266 MHz not ot
be found in the imx8mm_fracpll_tbl, since it is entered there with a
precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
fracpll frequency cannot be determined.
Correct the value in imx8mm_fracpll_tbl to match the one expanded by
MHZ(266) macro, rounding it down to MHz range only.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Clock initialization functionality has ambitious debug messages, which are
printed out when failures are triggered during execution:
- Separate frequency table lookup functions have the the same output that
makes it impossible to understand which function failed and produced the
output
- PLL decoding routine has a generic debug statement printed, which does
not state the actual value failed to be found
Extend the output for both cases with prefixing table lookup functions
output with function name, and report the failed value in PLL decoding
routine.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
We need those macros to instruct drivers on how to behave for SoC specific
quirks, so let's add it as done for other i.MX SoCs.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
This mpu handling works for every i.MXRT SoC that we have, so let's
generalize imxrt1050_region_config to imxrt_region_config.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
When building imx8mp_evk_defconfig with LTO, the compiler complains
about type mismatch of function imx_eqos_txclk_set_rate() in file
drivers/net/dwc_eth_qos.c:845:12
which contains a weak definition of this function, vs file
arch/arm/mach-imx/imx8m/clock_imx8mm.c
which contains an implementation.
Change the type of this function in the implementation to fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On ARM, the gd pointer is stored in registers r9 / x18. For this the
-ffixed-r9 / -ffixed-x18 flag is used when compiling, but using global
register variables causes errors when building with LTO, and these
errors are very difficult to overcome.
Richard Biener says [1]:
Note that global register vars shouldn't be used with LTO and if they
are restricted to just a few compilation units the recommended fix is
to build those CUs without -flto.
We cannot do this for U-Boot since all CUs use -ffixed-reg flag.
It seems that with LTO we could in fact store the gd pointer differently
and gain performance or size benefit by allowing the compiler to use
r9 / x18. But this would need more work.
So for now, when building with LTO, go the clang way, and instead of
declaring gd a global register variable, we make it a function call via
macro.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=68384
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
instead using ls and awk to determine file size use stat instead.
This fixes an invalid size reporting for user or group names that have
spaces in them.
This adds a dependency on the stat application which is part of
the coreutils package which also includes ls.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.
Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Carrier board for
creating complete i.Core MX8M Mini C.TOUCH 2.0 board.
Linux dts commit details:
commit <a142252061ff> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
C.TOUCH 2.0")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. In order to
convert to using the DWC SATA driver under DM further migrations are
required.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts the arch/arm/mach-imx/imx_bootaux.c changes of commit
805b3cac1e. The loader function name was changed so that it does
not clash with the generically available function in lib/elf.c.
imx-bootaux loads an elf file linked for an auxilary core. Thus the
loader function requires address translation from the auxilary core's
address space to where those are mapped into U-Boot's address space.
So the elf loader is specific and must not be replaced with a generic
loader which doesn't provide the address translation functionality.
Fixes commit 805b3cac1e ("lib: elf: Move the generic elf
loading/validating functions to lib")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The OCRAM_S is regular memory, just like the OCRAM, add it to the MMU
tables so it can be used and cached.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add DEK encapsulation support for imx8. The DEK blob is generated by the
SECO through the SCFW API.
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add DEK blob encapsulation support for IMX8M through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application call.
U-boot sends and receives the DEK and the DEK blob binaries through OP-TEE
dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
It is highly recommended to set the PRIBLOB bitfield to 0x3 once your
encrypted boot image has booted up, this prevents the generation of new
blobs that can be used to decrypt an encrypted boot image. The PRIBLOB is
a sticky type bit and cannot be changed until the next power on reset.
Add the set_priblob_bitfield U-Boot command to prevent the generation of
new blobs.
Signed-off-by: Clement Le Marquis <clement.lemarquis@nxp.com>
Acked-by: Ye Li <Ye.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since cmd_dek is using CAAM JR, so enable the CMD_DEK only when
HAS_CAAM is set
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add some SOC level codes and build configurations to use HAB lib for
CONFIG_IMX_HAB (secure boot), like adding the SEC_CONFIG fuse, enable
fuse driver, CAAM clock function, and add CAAM secure RAM to MMU table.
The FSL_CAAM is temporally not enabled for iMX8M when CONFIG_IMX_HAB is set,
because we don't need the CAAM driver for SPL.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When building 32-bit targets with CONFIG_SECURE_BOOT and DEBUG enabled
the following warnings are displayed:
arch/arm/mach-imx/hab.c:840:41: warning: format '%lx' expects argument \
of type 'long unsigned int', but argument 3 has type 'uint32_t \
{aka unsigned int}' [-Wformat=]
printf("HAB check target 0x%08x-0x%08lx fail\n",
~~~~^
%08x
ddr_start, ddr_start + bytes);
arch/arm/mach-imx/hab.c:845:45: warning: format '%x' expects argument \
of type 'unsigned int', but argument 3 has type 'ulong \
{aka long unsigned int}' [-Wformat=]
printf("\nivt_offset = 0x%x, ivt addr = 0x%x\n", ivt_offset, ivt_addr);
~^
%lx
Fix warnings by providing the correct data type.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When booting in low power or dual boot modes the M4 binary is
authenticated by the M4 ROM code.
Add an option in hab_status command so users can retrieve M4 HAB
failure and warning events.
=> hab_status m4
Secure boot disabled
HAB Configuration: 0xf0, HAB State: 0x66
No HAB Events Found!
Add command documentation in mx6_mx7_secure_boot.txt guide.
As HAB M4 API cannot be called from A7 core the code is parsing
the M4 HAB persistent memory region. The HAB persistent memory
stores HAB events, public keys and others HAB related information.
The HAB persistent memory region addresses and sizes can be found
in AN12263 "HABv4 RVT Guidelines and Recommendations".
Reviewed-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The HABv4 implementation in ROM checks if HAB major version
in IVT header is 4.x.
The current implementation in hab.c code is only validating
HAB v4.0 and HAB v4.1 and may be incompatible with newer
HABv4 versions.
Modify verify_ivt_header() function to align with HABv4
implementation in ROM code.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add ability for hab_status command to show All HAB events and not just
HAB failure events
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently it's not possible to authenticate additional boot images in HAB
open configuration.
The hab.c code is checking if the SEC_CONFIG[1] fuse is programmed prior
to calling the hab_authenticate_image() API function. Users cannot check
if their additional boot images has been correctly signed prior to closing
their device.
Enable hab.c to authenticate additional boot images in open mode so HAB
events can be retrieved through get_hab_status() function.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Modify to use hab_rvt_failsafe function for failsafe ROM API, not
directly call its ROM address. This function will wrap the sip call for iMX8M
platforms.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Calling csf_is_valid() with an un-signed image may lead to data abort
as the CSF pointer could be pointing to a garbage address when accessed
in HAB_HDR_LEN(*(const struct hab_hdr *)(ulong)ivt_initial->csf).
Authenticate image from DDR location 0x80800000...
Check CSF for Write Data command before authenticating image
data abort
pc : [<fff5494c>] lr : [<fff54910>]
reloc pc : [<8780294c>] lr : [<87802910>]
sp : fdf45dc8 ip : 00000214 fp : 00000000
r10: fffb6170 r9 : fdf4fec0 r8 : 00722020
r7 : 80f20000 r6 : 80800000 r5 : 80800000 r4 : 00720000
r3 : 17a5aca3 r2 : 00000000 r1 : 80f2201f r0 : 00000019
Flags: NzcV IRQs off FIQs off Mode SVC_32
Resetting CPU ...
resetting ...
To avoid such errors during authentication process, validate IVT structure
by calling validate_ivt function which checks the following values in an IVT:
IVT_HEADER = 0x4X2000D1
ENTRY != 0x0
RES1 = 0x0
DCD = 0x0 /* Recommended */
SELF != 0x0 /* Absoulute address of IVT */
CSF != 0x0
RES2 = 0x0
This commit also checks if Image's start address is 4 byte aligned.
commit "0088d127 MLK-14945 HAB: Check if IVT valid before authenticating image"
removed as this patch addresses the issue.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are some changes to support ARM64 i.MX8M platform in this patches:
1. The hab_rvt base and function vectors are different as i.MX6/7
2. Need to bypass an workaround for i.MX6 to fix problem in MMU.
3. The x18 register needed save & restore before calling any HAB API. According
to ARM procedure call spec, the x18 is caller saved when it is used as
temporary register. So calling HAB API may scratch this register, and
cause crash once accessing the gd pointer.
On ARMv7, the r9 is callee saved when it is used as variable register. So
no need to save & restore it.
4. Add SEC_CONFIG fuse for iMX8M
When current EL is not EL3, the direct calling to HAB will fail because
CAAM/SNVS can't initialize at non-secure mode. In this case, we use
SIP call to run the HAB in ATF.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When loading kernel image, the image size is parsed from header, so it
does not include the CSF and IVT.
Add back the authenticate_image function to wrap the imx_hab_authenticate_image
with calculating IVT offset and full image size.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Prior instantiating RNG we have to ensure if the CAAM job rings are
available. Avoid hardcoded job ring max size and use the definition at
fsl_sec.h
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Prior calling sec_in32() we have to ensure CAAM clock is enabled, the
function sec_in32() is reading CAAM registers and if CAAM clock is disabled
the system will hang.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The CAAM output ring size register offset is currently defined in fsl_sec.h
as FSL_CAAM_ORSR_JRa_OFFSET, use this definition to avoid hardcoded value in
i.MX common code.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This code was originally developed by Raul Cardenas <raul.casas@nxp.com>
and modified to be applied in U-Boot imx_v2017.03.
More information about the initial submission can be seen
in the link below:
https://lists.denx.de/pipermail/u-boot/2016-February/245273.html
i.MX7D has an a protection feature for Manufacturing process.
This feature uses asymmetric encryption to sign and verify
authenticated software handled between parties. This command
enables the use of such feature.
The private key is unique and generated once per device.
And it is stored in secure memory and only accessible by CAAM.
Therefore, the public key generation and signature functions
are the only functions available for the user.
The manufacturing-protection authentication process can be used to
authenticate the chip to the OEM's server.
Command usage:
Print the public key for the device.
- mfgprot pubk
Generates Signature over given data.
- mfgprot sign <data_address> <data_size>
Signed-off-by: Raul Ulises Cardenas <raul.casas@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MQ B2 is using same value in OCOTP_READ_FUSE_DATA like B1, so
we have to check the ROM verision to distinguish the revision.
As we have checked the B1 rev for sticky bits work around in
secure boot. So it won't apply on B2.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For dual core and single core iMX8M parts, the thermal node and PMU node
in kernel DTB also needs update to remove the refers to deleted core nodes.
Otherwise both driver will fail to work.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are 3 part numbers for 11x11 i.MX8MNano with different core number
configuration: UltraLite Quad/Dual/Solo
Comparing with i.MX8MN Lite parts, they have MIPI DSI disabled. So
checking the MIPI DSI disable fuse to recognize these parts.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add dedicated defconfigs for iMX8MN low drive mode which set the VDD_SOC
and VDD_DRAM to 0.8v, DDR at 1600MTS (800Mhz clock) and GPU at 200Mhz.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for iMX8MN LPDDR4 EVK board which uses 2GB LPDDR4 and
PCA9450B PMIC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The u-boot-with-spl.imx is a concatenation of SPL and u-boot.uim.
The u-boot.uim is u-boot.bin wrapped in uImage. In case OF_SEPARATE
is enabled, the u-boot.bin does not contain control DT for U-Boot,
and so u-boot.uim does not contain the DT, and so u-boot-with-spl.imx
does not contain the DT, and a system where u-boot-with-spl.imx is
written to offset 1024B to the start of storage no longer boots, as
it is missing DT.
In case OF_SEPARATE is enabled, u-boot.img contains both u-boot.bin
and the necessary DTs. Therefore, use u-boot.img instead of u-boot.uim
to generate u-boot-with-spl.imx when OF_SEPARATE is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Instead of hard-coding the offset of DRAM entries in MMU table all over
the code, auto-detect the offset. This removes error-prone code which
would break e.g. in case the MMU table is modified.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The serial number OTP is similar to the imx7 version, except that the
register names are different. This also sets serial# directly, instead of
providing board_get_serial.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The size is derived from the FIT image itself. Any alignment
requirements are machine-specific and known by the board code. Thus
the total length can be derived from the FIT image and knowledge of
the platform. The 'length' argument is redundant. Remove it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CC: Matt Porter <mporter@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lauri Hintsala <lauri.hintsala@silabs.com<mailto:lauri.hintsala@silabs.com>>
Signed-off-by: Tom Rini <trini@konsulko.com<mailto:trini@konsulko.com>>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Modify the GPT common platform driver for mx7 which only use 24Mhz
OSC as clock source.
Note: at default, the mx7d will use system counter as timer. The GPT
is disabled.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When boot type could not be detected from rom sw info,
read sbmr1 to detect, here we only use it to detect FLEXSPI
boot, because ROM not update it in rom sw info.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since we remove SATA device before boot OS, when AHCI is enabled, update
the codes to remove AHCI device.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX8MP has shifted market segment fuse one bit from 0x440 [7:6] to [6:5],
correct it in imx common codes.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add NAND boot support for i.MX8MP by adding i.MX8MP in nandbcb support
list, reading boot_search_count from fuse.
i.MX8MN NAND boot is same as i.MX8MP, fix some issues as well.
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006656. In nandbcb_set_boot_config, an integer overflow
occurs, with the result converted to a wider integer type.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006658. In fill_dbbt_data, an integer overflow occurs,
with the result converted to a wider integer type
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006657. In read_fcb, leak of memory to system
resource "fcb_raw_page". Adjust the sequence to check the mtd bad
block prior than allocation of "fcb_raw_page", also check the NULL
return of allocation.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006655. In write_fcb, leak of memory to resource
"fcb_raw_page". Since we have initialized the "ret" to 0, should return
the value of ret.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006654. In write_fcb, use of an uninitialized
variable "ret".
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use
CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.
The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)
It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.
Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use %u and not %d for unsigned values.
Print kHz and not khz.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Calling ahab_close cmd force the user to interact for confirmation.
This is not user-friendly when using this cmd during factory process.
Allow the user to pass '-y' option to bypass this confirmation.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Introduce weak function board_mem_get_layout() which allows overriding
the memory layout from board code in runtime, useful for handling
different SKU versions.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
the mem_map structure containing the size of SDRAM is used in various
cache functions in cache_v8.c thus we need to update it with the
sdram size the board is configured with as well. Without this
the cache functions do not get setup properly and can hang
in the case where a board reports more SDRAM than defined in
PHYS_SDRAM_SIZE.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Fix the following warning:
arch/arm/mach-imx/imx8/ahab.c:105:3: warning: implicit declaration of function ‘flush_dcache_range’ [-Wimplicit-function-declaration]
flush_dcache_range(s, e);
^~~~~~~~~~~~~~~~~~
Include cpu_func.h header which declares the flush_dcache_range()
function.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c: In function ‘authenticate_os_container’:
arch/arm/mach-imx/imx8/ahab.c:96:9: warning: format ‘%x’ expects argument of type
‘unsigned int’, but argument 9 has type ‘ulong {aka long unsigned int}’ [-Wformat=]
debug("img %d, dst 0x%x, src 0x%x, size 0x%x\n",
Fix those by using "%lu" specified.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c:110:63: warning: format ‘%x’ expects
argument of type ‘unsigned int’, but argument 2 has type ‘u64 {aka long
long unsigned int}’ [-Wformat=]
Fix those by using %llx
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
GE B1x5v2 patient monitor series is similar to the CARESCAPE Monitor
series (GE Bx50). It consists of a carrier PCB used in combination
with a Congatec QMX6 SoM. This adds U-Boot support using device model
everywhere and SPL for memory initialization.
Proper configuration is provided as 'ge_b1x5v2_defconfig' and the
combined image u-boot-with-spi.imx can be flashed directly to 1024
byte offset to /dev/mtdblock0. Alternatively SPL and u-boot.imx can
be loaded separately via USB-OTG using e.g. imx_usb.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Allow using disable_ldb_di_clock_sources with just the combined
CONFIG_MX6QDL being enabled.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Implement the 'getprisec' subcommand of 'bmode' command for i.MX53 and
also the primary/secondary bootmode switching.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The command 'clocks' shows the following output:
=> clocks
PLL_A7_SPLL 528 MHz
PLL_A7_APLL 529 MHz
PLL_USB 0 MHz
Add some extra spaces so that the PLL_USB information gets aligned with
the previous reported frequencies.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The command 'clocks' shows the following output:
=> clocks
PLL_A7_SPLL 528 MHz
PLL_A7_APLL 529 MHz
PLL_USB 0 MHz
....
[do_mx7_showclocks] addr = 0x9FFB61F1
The last line is not useful at all, so just remove it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Ensure we terminate the line with a CR if we get an invalid sensor device
or reading.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In order to be able to run the I2C bus at 400Khz, the chip errata[1]
recommends that the peripheral clock runs out of the 24MHz oscillator.
Systems running I2C from OP-TEE before Linux executes - for example to
access a Secure Element [2] providing the cryptographic support - expect
this clock to be configured by the bootloader [3].
[1] IMX6SLCE Rev. 5, 02/2019, ERR007805.
[2] OP-TEE: support for NXP SE05X Plug and Trust (patch on the list).
[3] OP-TEE: check the imx_i2c.c driver (imx6 patch on the list).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This feature is incompatble with of-platdata since it uses the
U_BOOT_DEVICE() macro. With of-platdata the only devices permitted are
those created by dtoc.
The driver is not used in SPL anyway, so exclude it from that build.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This patch adds support for iMX6UL/ULL/SL/SDL MMDC into the DDR calibration
code. The difference between MX6DQ and MX6UL/ULL/SL is that the later SoCs
have 2 SDQS registers, just like MX6SX, while the MX6DQ/MX6SDL has 8.
Fixes: 4f4c128c65 ("ARM: mx6: ddr: Add support for iMX6SX")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Latest datasheet revE has removed MIMX8ML7D/5D/7C/5C parts, so
update u-boot to remove decoding and support for those parts.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add g_dnl_get_board_bcd_device_number, the new BCD value is used by uuu to distinguish
if the SPL supports the SDPV.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
We have a number of platforms that are a combination of a carrier board
and System-on-Module (SoM) that in turn allows for the board to have
different SoCs on it. In some cases, this is handled via board-specific
Kconfig options. In other cases we make use of
CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid
configurations as we will not in turn get options that in Kconfig are
selected by or depend on that setting.
To resolve this, make the SoC option a choice in Kconfig and make boards
depend on what they can support. This change opens us up for further
clean-ups in the cases where a single CONFIG_TARGET_xxx can support
different SoCs and today they do not, or do not cleanly do so.
Reported-by: Matt Porter <mporter@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Soeren Moch <smoch@web.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ian Ray <ian.ray@ge.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Cc: Simone CIANNI <simone.cianni@bticino.it>
Cc: Adam Ford <aford173@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Parthiban Nallathambi <parthiban@linumiz.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Niel Fourie <lusus@denx.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Silvio Fricke <open-source@softing.de>
Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Fill is code for programming the DDR_PHY_CMD_DESKEW_CONx registers,
which are optional, but can be used to fill in the byte lane delays.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement the 'getprisec' subcommand of 'bmode' command for i.MX7 by
reading out the SRC GPR10 bit 30. This bit is either set by the BootROM
if it switched to the secondary copy due to primary copy being corrupted
OR it can be overridden by the user.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add new 'getprisec' subcommand to 'bmode' command, which sets the return
value of the 'bmode' command to either 0 if the system booted from primary
copy or to 1 if the system booted from secondary copy. This can be used
e.g. in 'test' command to determine which copy of the system is running.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The i.MX6/i.MX7 is capable of booting a secondary "redundant" system
image in case the primary one is corrupted. The user can force this
boot mode as well by explicitly setting SRC GPR10 bit 30. This can be
potentially useful when upgrading the bootloader itself. Expose this
functionality to the user.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add the basic differentiation between i.MX6 and i.MX7 into the bmode
command, the mechanism really works almost the same on both platforms.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of hang()ing the system and thus disallowing any automated
recovery possibility from a HAB authentication failure, panic() .
The panic() function can be configured to hang() the system after
printing an error message, however the default is to reset the
system instead.
This allows redundant boot to work correctly. In case the primary
or secondary image cannot be authenticated, the system reboots and
bootrom can try to start the other one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based
on imx6ULL SoC from NXP and provision for expansion board. This
commit adds support only for SBC with NAND.
CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 45C
Reset cause: WDOG
Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND
Board: MYiR MYS-6ULX 6ULL Single Board Computer
DRAM: 256 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: FEC0
Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Checkpatch reports the following issue:
ERROR: space prohibited before that ',' (ctx:WxW)
#936: FILE: arch/arm/mach-imx/imx8m/soc.c:936:
+ 0, 0 , 0, 0, 0, 0, &res);
Remove the unneeded space.
^
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
According to i.MX 7Solo Applications Processor Reference Manual,
2.1.3 Cortex-M4 Memory Map, M4 can address only 1536MB of DDRC
(Start Address: 0x8000_0000; End Address: 0xDFFF_FFFF).
Correct DDRC size to 0x60000000.
Fixes: c0f037f6("mach-imx: bootaux: elf firmware support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Even if the HAB fuse is not set we want to be able to use the Cryptographic
Accelerator and Assurance Module (CAAM) for generating random numbers. So
SYS_FSL_HAS_SEC should be selected even if IMX_HAB is not set.
arch_misc_init() has to be called to initialize the CAAM.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Convert pcm058 support to use device trees and the driver model.
Add rudimentary boot scripts to the environment, expand README.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
