Once u-boot sets the spin table to cache-enabled memory, old kernel which
uses cache-inhibit mapping without coherence will not work properly. We
use this temporary fix until kernel has updated its spin table code.
For now this fix is activated by default. To disable this fix for new
kernel, set environmental variable "spin_table_compat=no". After kernel
has updated spin table code, this default shall be changed.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The work-around for erratum A-004849 ("CoreNet fabric (CCF) can exhibit a
deadlock under certain traffic patterns causing the system to hang") is
implemented via the PBI (pre-boot initialization code, typically attached
to the RCW binary). This is because the work-around is easier to implement
in PBI than in U-Boot itself.
It is still useful, however, for the 'errata' command to tell us whether
the work-around has been applied. For A-004849, we can do this by verifying
that the values in the specific registers that the work-around says to
update.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P5040 has an e5500 core, so CONFIG_SYS_PPC64 should be defined in
config_mpc85xx.h. This macro was absent in the initial P5040 patch because
it crossed paths with the patch that introduced the macro.
Also delete CONFIG_SYS_FSL_ELBC_MULTIBIT_ECC, since it's not used in the
upstream U-Boot. It's a holdover from the SDK.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There were a number of shared files that were using
CONFIG_SYS_MPC85xx_DDR_ADDR, or CONFIG_SYS_MPC86xx_DDR_ADDR, and
several variants (DDR2, DDR3). A recent patchset added
85xx-specific ones to code which was used by 86xx systems.
After reviewing places where these constants were used, and
noting that the type definitions of the pointers assigned to
point to those addresses were the same, the cleanest approach
to fixing this problem was to unify the namespace for the
85xx, 83xx, and 86xx DDR address definitions.
This patch does:
s/CONFIG_SYS_MPC8.xx_DDR/CONFIG_SYS_MPC8xxx_DDR/g
All 85xx, 86xx, and 83xx have been built with this change.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Andy Fleming <afleming@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Update CONFIG_RAMBOOT and CONFIG_NAND_SPL references to accept CONFIG_SPL
and CONFIG_SPL_BUILD, respectively. CONFIG_NAND_SPL can be removed once
the last mpc85xx nand_spl target is gone.
CONFIG_RAMBOOT will need to remain for other use cases, but it doesn't
seem right to overload it for meaning SPL as well as nand_spl does. Even
if it's somewhat appropriate for the main u-boot, the SPL itself isn't
(necessarily) ramboot, and we don't have separate configs for SPL and
main u-boot. It was also inconsistent, as other platforms such as
mpc83xx didn't use CONFIG_RAMBOOT in this way.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
cpu_init_nand.c is renamed to spl_minimal.c as it is not really NAND-specific.
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: factor out START, and change cpu_init_nand.c to spl_minimal.c
Cc: Andy Fleming <afleming@freescale.com>
A subsequent patch will conditionalize some of the files that are
currently unconditional.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
It applies to non-Freescale 85xx boards as well as Freescale boards,
so it doesn't belong in board/freescale. Plus, it needs to come out
of nand_spl if it's to be used by the new SPL.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
It's arch code and not a driver, so move it where it belongs. When it
originally went into drivers/misc there was no 8xxx CPU directory.
This will make new-SPL support a little easier since we can keep the CPU
stuff together and not need to pull stuff in from drivers/misc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
In the RAMBOOT/SPL case we were creating a TLB entry starting at
CONFIG_SYS_MONITOR_BASE, and just hoping that the base was properly
aligned for the TLB entry size. This turned out to not be the case
with NAND SPL because the main U-Boot starts at an offset into the image
in order to skip the SPL itself.
Fix the TLB entry to always start at a proper alignment. We still assume that
CONFIG_SYS_MONITOR_BASE doesn't start immediately before a large-page boundary
thus requiring multiple TLB entries.
Signed-off-by: Scott Wood <scottwood@frescale.com>
Cc: Andy Fleming <afleming@freescale.com>
This was introduced by commit 2446151974, but it
fails in a minimal SPL build where the only thing in arch/powerpc/lib is
cache.c, which apparently doesn't generate any fixup records.
The problem is reported to occur with GCC 3.x, so insist on GCC 4.0 or newer.
Patterned after checkthumb as suggested by Tom Rini.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Tom Rini <trini@ti.com>
--
v2: test gcc version instead of testing nothing
Now outputs like this:
L2: 512 KB already enabled, moving to 0xf8f80000
rather than this:
L2: 512 KB already enabledmoving to 0xf8f80000
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Previously, in many if not all configs we were creating overlapping TLB entries
which is illegal. This caused a crash during boot when moving p2020rdb NAND SPL
into L2 SRAM.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
--
Prabhakar, please test that debug still works.
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.
As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is no point to put speed into
pipe anymore so it's removed and a bunch of host drivers fixed to
look at usb_device->speed instead.
Old usbdescriptors.h included is not removed as it seems to be
used by old USB device code.
This makes usb.h and usbdevice.h incompatible. Fortunately the
only place that tries to include both are the old MUSB code and
it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute
on musb_regs structure but this attribute seems to be unneeded
(old MUSB code doesn't support any DMA at all).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
fdt.c:91:78: warning: Using plain integer as NULL pointer
fdt.c:103:78: warning: Using plain integer as NULL pointer
speed.c:55:11: warning: symbol 'corecnf_tab' was not declared. Should it be static?
speed.c:519:5: warning: symbol 'do_clocks' was not declared. Should it be static?
mpc8313erdb.c:73:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:74:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:75:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:76:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:79:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:80:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:81:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:82:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:85:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:86:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:87:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:88:17: warning: obsolete struct initializer, use C99 syntax
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
fsl_corenet_serdes.c:485:6: warning: symbol '__soc_serdes_init' was not declared. Should it be static?
cpu_init.c:185:6: warning: symbol 'invalidate_cpc' was not declared. Should it be static?
bcsr.c:28:27: warning: non-ANSI function declaration of function 'enable_8568mds_duart'
bcsr.c:39:33: warning: non-ANSI function declaration of function 'enable_8568mds_flash_write'
bcsr.c:46:34: warning: non-ANSI function declaration of function 'disable_8568mds_flash_write'
bcsr.c:53:29: warning: non-ANSI function declaration of function 'enable_8568mds_qe_mdio'
bcsr.c:28:33: warning: non-ANSI function declaration of function 'enable_8569mds_flash_write'
bcsr.c:33:34: warning: non-ANSI function declaration of function 'disable_8569mds_flash_write'
bcsr.c:38:28: warning: non-ANSI function declaration of function 'enable_8569mds_qe_uec'
bcsr.c:63:47: warning: non-ANSI function declaration of function 'disable_8569mds_brd_eeprom_write_protect'
ngpixis.c:245:1: error: directive in argument list
ngpixis.c:247:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
ctrl_regs.c:31:5: warning: symbol 'fsl_ddr_get_version' was not declared. Should it be static?
cpu.c:135:14: warning: non-ANSI function declaration of function 'cpu_mask'
cpu.c:154:18: warning: non-ANSI function declaration of function 'cpu_numcores'
cpu.c:37:17: warning: symbol 'cpu_type_list' was not declared. Should it be static?
cpu.c:117:17: warning: symbol 'cpu_type_unknown' was not declared. Should it be static?
fsl_lbc.c:14:6: warning: symbol '__lbc_sdram_init' was not declared. Should it be static?
and:
lc_common_dimm_params.c:15:1: warning: symbol 'compute_cas_latency_ddr3' was not declared. Should it be static?
making it static produces the following compiler warning:
lc_common_dimm_params.c:15:1: warning: 'compute_cas_latency_ddr3' defined but not used [-Wunused-function]
so we protect it with the preprocessor.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
traps.c:*:1: warning: symbol 'print_backtrace' was not declared. Should it be static?
traps.c:93:1: warning: symbol '_exception' was not declared. Should it be static?
board.c:166:6: warning: symbol '__board_add_ram_info' was not declared. Should it be static?
board.c:174:5: warning: symbol '__board_flash_wp_on' was not declared. Should it be static?
board.c:187:6: warning: symbol '__cpu_secondary_init_r' was not declared. Should it be static?
board.c:265:12: warning: symbol 'init_sequence' was not declared. Should it be static?
board.c:348:5: warning: symbol '__fixup_cpu' was not declared. Should it be static?
board.c:405:53: warning: Using plain integer as NULL pointer
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
extable.c:66:9: warning: symbol 'ex_tab_message' was not declared. Should it be static?
making it static can produce a new build warning on some boards:
extable.c:66:12: warning: 'ex_tab_message' defined but not used [-Wunused-variable]
but ex_tab_message doesn't do much even when used, so just remove it.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
a fixup __iomem definition in arch code appears to be placed there as a cover
up from a code import from linux when u-boot didn't yet have a compiler.h,
introduced by commit 812711ce6b "Implement
__raw_{read,write}[bwl] on all architectures".
git show 812711ce6b3a386125dcf0d6a59588e461abbb87:include/linux/compiler.h
fatal: Path 'include/linux/compiler.h' exists on disk, but not in '812711ce6b3a386125dcf0d6a59588e461abbb87'.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
u-boot's byteorder headers did not contain endianness attributions
for use with sparse, causing a lot of false positives. Import the
kernel's latest definitions, and enable them by including compiler.h
and types.h. They come with 'const' added for some swab functions, so
fix those up, too:
include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default]
Also, note: u-boot's historic __BYTE_ORDER definition has been
preserved (for the time being at least).
We also remove ad-hoc barrier() definitions, since we're including
compiler.h in files that hadn't in the past:
macb.c:54:0: warning: "barrier" redefined [enabled by default]
In addition, including compiler.h in byteorder changes the 'noinline'
definition to expand to __attribute__((noinline)). This fixes
arch/powerpc/lib/bootm.c:
bootm.c:329:16: error: attribute '__attribute__': unknown attribute
bootm.c:329:16: error: expected ')' before '__attribute__'
bootm.c:329:25: error: expected identifier or '(' before ')' token
powerpc sparse builds yield:
include/common.h:356:22: error: marked inline, but without a definition
the unknown-reason inlining without a definition is considered obsolete
given it was part of the 2002 initial commit, and no arm version was
'fixed.'
also fixed:
ydirectenv.h:60:0: warning: "inline" redefined [enabled by default]
and:
Configuring for devconcenter - Board: intip, Options: DEVCONCENTER
make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1
make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2
powerpc-fsl-linux-size: './u-boot': No such file
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available
4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here
and:
In file included from crc32.c:50:0:
crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration]
crc32table.h:4:1: error: initializer element is not constant
crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]')
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[trini: Remove '#endif' in include/common.h around setenv portion]
Signed-off-by: Tom Rini <trini@ti.com>
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years. Get rid of the dead
weight.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
This processor, though very similar to other members of the
PowerQUICC II Pro family (namely 8308, 8360 and 832x), provides
yet another feature set than any supported sibling.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Introduce a new configuration token CONFIG_MPC830x to be shared among
mpc8308 and mpc8309. Define it for existing 8308 boards, and refactor
existing common code so to make future introduction of 8309 simpler.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
simplify #if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832x)
for qe variables
with #if defined(CONFIG_QE)
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The timeout_save variable was only used by the DDR111_134
erratum code. It was being set, but never used. Newer compilers
will actually complain about this.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, the SRIO and PCIE boot master module will be compiled into the
u-boot image if the macro "CONFIG_FSL_CORENET" has been defined. And this
macro has been included by all the corenet architecture platform boards.
But in fact, it's uncertain whether all corenet platform boards support
this feature.
So it may be better to get rid of the macro "CONFIG_FSL_CORENET", and add
a special macro for every board which can support the feature. This
special macro will be defined in the header file
"arch/powerpc/include/asm/config_mpc85xx.h". It will decide if the SRIO
and PCIE boot master module should be compiled into the board u-boot image.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Starting from QMan3.0, the QMan clock cycle needs be exposed so that the kernel
driver can use it to calculate the shaper prescaler and rate.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Because QMan3.0 and BMan2.1 used ip_cfg in ip_rev_2 register to differ the
total portal number, buffer pool number etc, we can use this info to limit
those resources in kernel driver.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
New corenet platforms with chassis2 have separated DDR clock inputs. Use
CONFIG_DDR_CLK_FREQ for DDR clock. This patch also cleans up the logic of
detecting and displaying synchronous vs asynchronous mode.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Move spin table to cached memory to comply with ePAPR v1.1.
Load R3 with 64-bit value if CONFIG_SYS_PPC64 is defined.
'M' bit is set for DDR TLB to maintain cache coherence.
See details in doc/README.mpc85xx-spin-table.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
R6 was in ePAPR draft version but was dropped in official spec.
Removing it to comply.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since empty DIMM slot is allowed on other than the first slot, remove the
error message if SPD is not found in this case.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Based on populated DIMMs, automatically select from cs0_cs1_cs2_cs3 or
cs0_cs1 interleaving, or non-interleaving if not available.
Fix the message of interleaving disabled if controller interleaving
is enabled but DIMMs don't support it.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After DDR controller is enabled, it performs a calibration for the
transmit data vs DQS paths. During this calibration, the DDR controller
may make an inaccurate calculation, resulting in a non-optimal tap point.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Boot space translation utilizes the pre-translation address to select
the DDR controller target. However, the post-translation address will be
presented to the selected DDR controller. It is possible that the pre-
translation address selects one DDR controller but the post-translation
address exists in a different DDR controller when using certain DDR
controller interleaving modes. The device may fail to boot under these
circumstances. Note that a DDR MSE error will not be detected since DDR
controller bounds registers are programmed to be the same when configured
for DDR controller interleaving.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When ECC is enabled, DDR controller needs to initialize the data and ecc.
The wait time can be calcuated with total memory size, bus width, bus speed
and interleaving mode. If it went wrong, it is bettert to timeout than
waiting for D_INIT to clear, where it probably hangs.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix handling quad-rank DIMMs in a system with two DIMM slots and first
slot supports both dual-rank DIMM and quad-rank DIMM.
For systems with quad-rank DIMM and double dual-rank DIMMs, cs_config
registers need to be enabled to maintain proper ODT operation. The
inactive CS should have bnds registers cleared.
Fix the turnaround timing for systems with all chip-selects enabled. This
wasn't an issue before because DDR was running lower than 1600MT/s with
this interleaving mode.
Fix DDR address calculation. It wasn't an issue until we have multiple
controllers with each more than 4GB and interleaving is disabled.
It also fixes the message of DDR: 2 GiB (DDR3, 64-bit, CL=0.5, ECC off)
when debugging DDR and first DDR controller is disabled. With the fix,
the first enabled controller information will be displayed.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
DDRC ver 4.7 adds DDR_SLOW bit in sdram_cfg_2 register. This bit needs to be
set for speed lower than 1250MT/s.
CDR1 and CDR2 are control driver registers. ODT termination valueis for
IOs are defined. Starting from DDRC 4.7, the decoding of ODT for IOs is
000 -> Termsel off
001 -> 120 Ohm
010 -> 180 Ohm
011 -> 75 Ohm
100 -> 110 Ohm
101 -> 60 Ohm
110 -> 70 Ohm
111 -> 47 Ohm
Add two write leveling registers. Each QDS now has its own write leveling
start value. In case of zero value, the value of QDS0 will be used. These
values are board-specific and are set in board files.
Extend DDR register timing_cfg_1 to have 4 bits for each field.
DDR control driver registers and write leveling registers are added to
interactive debugging for easy access.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The multirate ethernet media access controller (mEMAC) interfaces to
10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII
interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Freescale B4860 and variant SoCs. Features of B4860 are
(incomplete list):
Six fully-programmable StarCore SC3900 FVP subsystems, divided into three
clusters-each core runs up to 1.2 GHz, with an architecture highly
optimized for wireless base station applications
Four dual-thread e6500 Power Architecture processors organized in one
cluster-each core runs up to 1.8 GHz
Two DDR3/3L controllers for high-speed, industry-standard memory interface
each runs at up to 1866.67 MHz
MAPLE-B3 hardware acceleration-for forward error correction schemes
including Turbo or Viterbi decoding, Turbo encoding and rate matching,
MIMO MMSE equalization scheme, matrix operations, CRC insertion and
check, DFT/iDFT and FFT/iFFT calculations, PUSCH/PDSCH acceleration,
and UMTS chip rate acceleration
CoreNet fabric that fully supports coherency using MESI protocol between
the e6500 cores, SC3900 FVP cores, memories and external interfaces.
CoreNet fabric interconnect runs at 667 MHz and supports coherent and
non-coherent out of order transactions with prioritization and
bandwidth allocation amongst CoreNet endpoints.
Data Path Acceleration Architecture, which includes the following:
Frame Manager (FMan), which supports in-line packet parsing and general
classification to enable policing and QoS-based packet distribution
Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading
of queue management, task management, load distribution, flow ordering,
buffer management, and allocation tasks from the cores
Security engine (SEC 5.3)-crypto-acceleration for protocols such as
IPsec, SSL, and 802.16
RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and
outbound). Supports types 5, 6 (outbound only)
Large internal cache memory with snooping and stashing capabilities for
bandwidth saving and high utilization of processor elements. The
9856-Kbyte internal memory space includes the following:
32 Kbyte L1 ICache per e6500/SC3900 core
32 Kbyte L1 DCache per e6500/SC3900 core
2048 Kbyte unified L2 cache for each SC3900 FVP cluster
2048 Kbyte unified L2 cache for the e6500 cluster
Two 512 Kbyte shared L3 CoreNet platform caches (CPC)
Sixteen 10-GHz SerDes lanes serving:
Two Serial RapidIO interfaces. Each supports up to 4 lanes and a total
of up to 8 lanes
Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue-
less antenna connection
Two 10-Gbit Ethernet controllers (10GEC)
Six 1G/2.5-Gbit Ethernet controllers for network communications
PCI Express controller
Debug (Aurora)
Two OCeaN DMAs
Various system peripherals
182 32-bit timers
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Freescale T4240 SoC. Feature of T4240 are
(incomplete list):
12 dual-threaded e6500 cores built on Power Architecture® technology
Arranged as clusters of four cores sharing a 2 MB L2 cache.
Up to 1.8 GHz at 1.0 V with 64-bit ISA support (Power Architecture
v2.06-compliant)
Three levels of instruction: user, supervisor, and hypervisor
1.5 MB CoreNet Platform Cache (CPC)
Hierarchical interconnect fabric
CoreNet fabric supporting coherent and non-coherent transactions with
prioritization and bandwidth allocation amongst CoreNet end-points
1.6 Tbps coherent read bandwidth
Queue Manager (QMan) fabric supporting packet-level queue management and
quality of service scheduling
Three 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support
Memory prefetch engine (PMan)
Data Path Acceleration Architecture (DPAA) incorporating acceleration for
the following functions:
Packet parsing, classification, and distribution (Frame Manager 1.1)
Queue management for scheduling, packet sequencing, and congestion
management (Queue Manager 1.1)
Hardware buffer management for buffer allocation and de-allocation
(BMan 1.1)
Cryptography acceleration (SEC 5.0) at up to 40 Gbps
RegEx Pattern Matching Acceleration (PME 2.1) at up to 10 Gbps
Decompression/Compression Acceleration (DCE 1.0) at up to 20 Gbps
DPAA chip-to-chip interconnect via RapidIO Message Manager (RMAN 1.0)
32 SerDes lanes at up to 10.3125 GHz
Ethernet interfaces
Up to four 10 Gbps Ethernet MACs
Up to sixteen 1 Gbps Ethernet MACs
Maximum configuration of 4 x 10 GE + 8 x 1 GE
High-speed peripheral interfaces
Four PCI Express 2.0/3.0 controllers
Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz with
Type 11 messaging and Type 9 data streaming support
Interlaken look-aside interface for serial TCAM connection
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Four I2C controllers
Four 2-pin or two 4-pin UARTs
Integrated Flash controller supporting NAND and NOR flash
Two eight-channel DMA engines
Support for hardware virtualization and partitioning enforcement
QorIQ Platform's Trust Architecture 1.1
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The T4 has added devices to previous corenet implementations:
* SEC has 3 more DECO units
* New PMAN device
* New DCE device
This doesn't add full support for the new devices. Just some
preliminary support.
Move PMAN LIODN to upper half of register
Despite having only one LIODN, the PMAN LIODN is stored in the
upper half of the register. Re-use the 2-LIODN code and just
set the LIODN as if the second one is 0. This results in the
actual LIODN being written to the upper half of the register.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Corenet 2nd generation Chassis doesn't have ddr_sync bit in RCW. Only
async mode is supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Create new files to handle 2nd generation Chassis as the registers are
organized differently.
- Add SerDes protocol parsing and detection
- Add support of 4 SerDes
- Add CPRI protocol in fsl_serdes.h
The Common Public Radio Interface (CPRI) is publicly available
specification that standardizes the protocol interface between the
radio equipment control (REC) and the radio equipment (RE) in wireless
basestations. This allows interoperability of equipment from different
vendors,and preserves the software investment made by wireless service
providers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Corenet 2nd generation Chassis has different RCW and registers for SerDes.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The QCSP registers are expanded and moved from offset 0 to offset 0x1000
for SoCs with QMan v3.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Expand the reference clock select to three bits
000: 100 MHz
001: 125 MHz
010: 156.25MHz
011: 150 MHz
100: 161.1328125 MHz
All others reserved
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Corenet based SoCs have different core clocks starting from Chassis
generation 2. Cores are organized into clusters. Each cluster has up to
4 cores sharing same clock, which can be chosen from one of three PLLs in
the cluster group with one of the devisors /1, /2 or /4. Two clusters are
put together as a cluster group. These two clusters share the PLLs but may
have different divisor. For example, core 0~3 are in cluster 1. Core 4~7
are in cluster 2. Core 8~11 are in cluster 3 and so on. Cluster 1 and 2
are cluster group A. Cluster 3 and 4 are in cluster group B. Cluster group
A has PLL1, PLL2, PLL3. Cluster group B has PLL4, PLL5. Core 0~3 may have
PLL1/2, core 4~7 may have PLL2/2. Core 8~11 may have PLL4/1.
PME and FMan blocks can take different PLLs, configured by RCW.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Panic if the number of cores is more than CONFIG_MAX_CPUS because it will
surely overflow gd structure.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Chassis generation 2 has different mask and shift. Use macro instead of
magic numbers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Using E6500 L1 cache as initram requires L2 cache enabled.
Add l2-cache cluster enabling.
Setup stash id for L1 cache as (coreID) * 2 + 32 + 0
Setup stash id for L2 cache as (cluster) * 2 + 32 + 1
Stash id for L2 is only set for Chassis 2.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
These assembly macros simplify codes to add and delete temporary TLB entries.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
FSL_HW_PORTAL_PME is used even when CONFIG_SYS_DPAA_PME is not defined.
Remove the #ifdef.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for the Freescale P5040 SOC, which is similar to the P5020.
Features of the P5040 are:
Four P5040 single-threaded e5500 cores built
Up to 2.4 GHz with 64-bit ISA support
Three levels of instruction: user, supervisor, hypervisor
CoreNet platform cache (CPC)
2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric
Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support Up to 1600MT/s
Memory pre-fetch engine
DPAA incorporating acceleration for the following functions
Packet parsing, classification, and distribution (FMAN)
Queue management for scheduling, packet sequencing and
congestion management (QMAN)
Hardware buffer management for buffer allocation and
de-allocation (BMAN)
Cryptography acceleration (SEC 5.2) at up to 40 Gbps SerDes
20 lanes at up to 5 Gbps
Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces
Two 10 Gbps Ethernet MACs
Ten 1 Gbps Ethernet MACs
High-speed peripheral interfaces
Two PCI Express 2.0/3.0 controllers
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Two I2C controllers
Four UARTs
Integrated flash controller supporting NAND and NOR flash
DMA
Dual four channel
Support for hardware virtualization and partitioning enforcement
Extra privileged level for hypervisor support
QorIQ Trust Architecture 1.1
Secure boot, secure debug, tamper detection, volatile key storage
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add a new device tree property named "fsl,liodn-offset-list"
holding a list of per pci endpoint permitted liodn offsets.
This property is useful in virtualization scenarios
that implement per pci endpoint partitioning.
The final liodn of a partitioned pci endpoint is
calculated by the hardware, by adding these offsets
to pci controller's base liodn, stored in the
"fsl,liodn" property of its node.
The liodn offsets are interleaved to get better cache
utilization. As an example, given 3 pci controllers,
the following liodns are generated for the pci endpoints:
pci0: 193 256 259 262 265 268 271 274 277
pci1: 194 257 260 263 266 269 272 275 278
pci2: 195 258 261 264 267 270 273 276 279
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P5040 does not have SRIO support, so there are no SRIO LIODNs.
Therefore, the functions that set the SRIO LIODNs should not be compiled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The liodn for the new PCIE controller included in P5040DS is no longer set
through a register in the guts register block but with one in the PCIE
register block itself. Update the PCIE CCSR structure to add the new liodn
register and add a new dedicated SET_PCI_LIODN_BASE macro that puts
the liodn in the correct register.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Commit 709389b6 unintentionally used the Unicode version of the
apostrophy. Replace it with the normal ASCII version.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum: A-004034
Affects: SRIO
Description: During port initialization, the SRIO port performs
lane synchronization (detecting valid symbols on a lane) and
lane alignment (coordinating multiple lanes to receive valid data
across lanes). Internal errors in lane synchronization and lane
alignment may cause failure to achieve link initialization at
the configured port width.
An SRIO port configured as a 4x port may see one of these scenarios:
1. One or more lanes fails to achieve lane synchronization.
Depending on which lanes fail, this may result in downtraining
from 4x to 1x on lane 0, 4x to 1x on lane R (redundant lane).
2. The link may fail to achieve lane alignment as a 4x, even
though all 4 lanes achieve lane synchronization, and downtrain
to a 1x. An SRIO port configured as a 1x port may fail to complete
port initialization (PnESCSR[PU] never deasserts) because of
scenario 1.
Impact: SRIO port may downtrain to 1x, or may fail to complete
link initialization. Once a port completes link initialization
successfully, it will operate normally.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix usb device-tree fixup:
- wrong modification of dr_mode and phy_type when
"usb1" is not mentioned inside hwconfig string;
now allows hwconfig strings like:
"usb2:dr_mode=host,phy_type=ulpi"
- add warning message for using usb_dr_mode
and usb_phy_type env variables (if either is used)
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the
workaround conditional.
In formal release document, the errata number should be ESDHC13 instead
of ESDHC136.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We should only write TSR_WIS to the SPRN_TSR register in
reset_85xx_watchdog.
The old code would cause the timer interrupt to be acknowledged when the
watchdog was reset, and we would then get no more timer interrupts.
This bug would affect all mpc85xx boards that have the watchdog enabled.
Signed-off-by: Mark Marshall <Mark.Marshall@omicron.at>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Users of familiar with the Linux gpiolib API expect that value parameter
to gpio_direction_output reflects the initial state of the output pin.
gpio_direction_output was always driving the output low, now it drives
it high or low according to the value provided.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
move most of mpc8xx hooks from cmd_ide.c into ide_preinit() and newly created
ide_init_postreset() (invoked after calling ide_reset after ide_preinit),
some cleanup to make checkpatch happy, enable IDE init hooks in configs of
affected boards.
confusingly, these hooks are used by more than just mpc8xx-based boards, and
therefore are placed in arch/ppc/lib/
note: checkpatch still emits warnings about using volatile
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Replace the in-place ad-hoc implementation of serial_puts() within
the drivers with default_serial_puts() call. This cuts down on the
code duplication quite a bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: James F. Dougherty <jfd@broadcom.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.
Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Marek Vasut <marex@denx.de>
Since the IOP480 (PPC401/3 variant from PLX) is only used on 2
boards that are not actively maintained, lets remove support
for it completely. This way the ppc4xx code will get a bit cleaner.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Marek Vasut <marex@denx.de>
Remove the parts depending either on disabled CONFIG_SERIAL_MULTI
or ifdefs around CONFIG_SERIAL_MULTI parts since CONFIG_SERIAL_MULTI
is now enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Remove the support for not-CONFIG_SERIAL_MULTI part from serial
port drivers and some board files. Since CONFIG_SERIAL_MULTI is
now enabled by default, that part is a dead code. Remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into iop480 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the iop480 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc85xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc85xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into both SCC and SMC mpc8260
serial drivers. These drivers were so far only usable directly, but this
patch also adds support for the multi method. This allows using more than
one serial driver alongside the mpc8260 drivers. Also, add a weak
implementation of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc8220 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc8220 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc5xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc5xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Move the registration of serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented mpc512x_serial_initialize() function, which is
implemented inside of the mpc512x serial driver allows encapsulation
of serialN_device within the mpc512x serial driver itself.
Also, remove the exports of serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the mpx512x serial driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Move the registration of serial_smc and serial_scc ports from
default serial_initialize() into CPU specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The exports of both serial_scc_device and serial_smc_device can
not yet be removed as they are still used in default_serial_console()
calls.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Properly spell out the whole structure member names when an initialized
varible is instantiated from the struct serial_driver. In case the
structure definition for struct serial_driver undergoes reordering,
there will be no impact on variables defined based on this structure.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: C Nauman <cnauman@diagraph.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Michal Simek <monstr@monstr.eu>
Since commit 50a47d0523
(net: punt bd->bi_ip_addr) booting old 2.4.x ppc kernels
is broken due to changed offsets of the fields in struct bd_t.
Offsets of the fields after removed bi_ip_addr are wrong,
causing wrong bus clocks and console baudrate configurations
and various other issues. Re-add the bi_ip_addr field to preserve
backward compatibility with older ppc kernels. Setting bi_ip_addr
in board.c is not really needed, grepping in the 2.4 linux tree
shows that bi_ip_addr is not accessed there. Adding bi_ip_addr
to struct bd_t for other arches isn't needed it seems. bd_t is
not used by other arches in the 2.4 linux tree.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
wait_ticks() calls get_ticks() without building a back chain which
makes gdb unhappy when doing back trace. This can also cause
improper memory accesses.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Instead of just shooting down the entry that covers CCSR, clear out
every TLB entry that isn't the one that we're executing out of.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Before proper environment is setup, we extract hwconfig and put it into a
buffer with size HWCONFIG_BUFFER_SIZE. We need to enlarge the buffer to
accommodate longer string. Since this macro is used in multiple files, we
move it into arch/powerpc/include/asm/config.h.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add one more argument to call function readline_into_buffer().
Fix print SPD format for negative values.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Only the first DIMM of first controller should fall back to raw timing
parameters if SPD is missing or corrupted.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Empty slot should be skipped when calculating CAS latency.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Faster DDR3 timing requires parameters exceeding previously defined
range. Extended parameters are fixed. Added some debug messages.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Restructure DDR interleaving option to support 3 and 4 DDR controllers
for 2-, 3- and 4-way interleaving.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Required by JEDEC 79-3E for high speed DDR3.
Also change "CSn disabled" message to debug.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When the DDR3 speed goes higher, we need to utilize fine offset
from SPD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some debug registers have non-zero default out of reset. If software is
not setting debug registers, skip writing to them to avoid unnecessary
overriding.
Also add debug messages for workarounds and debug registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For the cores with multiple threads, we need to figure out which physical
core a thread belongs. To match the core ids, update PIR registers and
spin tables.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In case more than 32 bit address is used, the EXT bit should be set.
Need to fix up address map for IFC #CS for 4, also need to move # of IFC
banks into config_mpc85xx.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We have actual topology infomation to find out exactly which core is present.
Calculate the number of cores if not specified.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Freescale's High-End SoC are going to have Integrated Flash controller
(IFC)'s support.
So add IFC LAW target ID support for High-End SoC or corenet SoC.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG). Need to define define
CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.
Enable missed e500v2 SoC i.e. MPC8536, MPC8544, MPC8548 and MPC8572 for
debug support.
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum A004510 says that under certain load conditions, modified
cache lines can be discarded, causing data corruption.
To work around this, several CCSR and DCSR register updates need to be
made in a careful manner, so that there is no other transaction in
corenet when the update is made.
The update is made from a locked cacheline, with a delay before to flush
any previous activity, and a delay after to flush the CCSR/DCSR update.
We can't use a readback because that would be another corenet
transaction, which is not allowed.
We lock the subsequent cacheline to prevent it from being fetched while
we're executing the previous cacheline. It is filled with nops so that a
branch doesn't cause us to fetch another cacheline.
Ordinarily we are running in a cache-inhibited mapping at this point, so
we temporarily change that. We make it guarded so that we should never
see a speculative load, and we never do an explicit load. Thus, only the
I-cache should ever fill from this mapping, and we flush/unlock it
afterward. Thus we should avoid problems from any potential cache
aliasing between inhibited and non-inhibited mappings.
NOTE that if PAMU is used with this patch, it will need to use a
dedicated LAW as described in the erratum. This is the responsibility
of the OS that sets up PAMU.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
These are not supported as individual build targets, but instead
are supported by another target.
The dead p4040 defines in particular had bitrotted significantly.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Unlike previous SOCs, the Freescale P5040 has a fifth DTSEC on the second
Fman, so add the Fman and SerDes macros for that DTSEC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, for NAND boot for the P1010/4RDB we hard code the DDR
configuration. We can still dynamically set the DDR bus width in
the nand spl so the P1010/4RDB boards can boot from the same
u-boot image
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
P1015 is the same as P1011 and P1016 is the same as P1012 from software
point of view. They have different packages but share SVRs.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For the powerpc processors with PCIE interface, boot location can be
configured from one PCIE interface by RCW. The processor booting from PCIE
can do without flash for u-boot image. The image can be fetched from another
processor's memory space by PCIE link connected between them.
The processor booting from PCIE is slave, the processor booting from normal
flash memory space is master, and it can help slave to boot from master's
memory space.
When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.
Environment and requirement:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image is in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure PCIE system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to one PCIE interface by RCW.
3. RCW should configure the SerDes, PCIE interfaces correctly.
4. Must set all the cores in holdoff by RCW.
5. Must be powered on before master's boot.
For the master module, need to finish these processes:
1. Initialize the PCIE port and address space.
2. Set inbound PCIE windows covered slave's u-boot image stored in
master's NOR flash.
3. Set outbound windows in order to configure slave's registers
for the core's releasing.
4. Should set the environment variable "bootmaster" to "PCIE1", "PCIE2"
or "PCIE3" using the following command:
setenv bootmaster PCIE1
saveenv
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When compile the slave image for boot from SRIO, no longer need to
specify which SRIO port it will boot from. The code will get this
information from RCW and then finishes corresponding configurations.
This has the following advantages:
1. No longer need to rebuild an image when change the SRIO port for
boot from SRIO, just rewrite the new RCW with selected port,
then the code will get the port information by reading new RCW.
2. It will be easier to support other boot location options, for
example, boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Get rid of the SRIOBOOT_MASTER build target, and to support for serving as
a SRIO boot master via environment variable. Set the environment variable
"bootmaster" to "SRIO1" or "SRIO2" using the following command:
setenv bootmaster SRIO1
saveenv
The "bootmaster" will enable the function of the SRIO boot master, and
this has the following advantages compared with SRIOBOOT_MASTER build
configuration:
1. Reduce a build configuration item in boards.cfg file.
No longer need to build a special image for master, just use a
normal target image and set the "bootmaster" variable.
2. No longer need to rebuild an image when change the SRIO port for
boot from SRIO, just set the corresponding value to "bootmaster"
based on the using SRIO port.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This erratum applies to the following SoCs:
P4080 rev 1.0, 2.0, fixed in rev 3.0
P2041 rev 1.0, 1.1, fixed in rev 2.0
P3041 rev 1.0, 1.1, fixed in rev 2.0.
Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround
may degrade performance. P4080 erratum CPU22 shares the same workaround.
So it is always enabled for P4080. For other SoCs, it can be disabled by
hwconfig with syntax:
fsl_cpu_a011:disable
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The code first aligns the SP to 16 then subtract 8, making it
8 bytes aligned. Furthermore the initial stack frame not
quite correct either.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Andy Fleming <afleming@freescale.com>
PowerPC mandates SP to be 16 bytes aligned.
Furthermore, a stack frame is added, pointing to the reset vector
which may in the way when gdb is walking the stack because
the reset vector may not accessible depending on emulator settings.
Also use a temp register so gdb doesn't pick up intermediate values.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prototype declaration of I/O operation functions are not correct. as both
'extern' and function definition are at same place.
Chage protoype declaration as static.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Return type of in_8, in_be16 and in_le16 should not be'int'. Update it to type
u8/u16/u32.
Although 'unsigned' for in_be32 and in_le32 is correct. But to make return type
uniform across the file changed to u32
Similarly, parameter passed to out_8, out_be16, out_le16 ,out_be32 & out_le32
should not be 'int'.Change it to type u8/u16/u32.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
All the global flag defines are the same across all arches. So unify them
in one place, and add a simple way for arches to extend for their needs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SET_PCI_LIODN() macro takes a compatible property string as a parameter, so that it knows
which PCI device tree node to look for. The calls to these macros are using a hard-coded string,
but we already have the CONFIG_SYS_FSL_PCIE_COMPAT macro which contains the same string, so we
should use that.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Commit 48f6a5c34 removed E bit. BSC9130/1 were left out due to patch apply
timing. Remove them now.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The BR_PHYS_ADDR(x) macro was missing parentheses around "x" in the macro
definition, so callers had to supply their own parenthesis.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
fsl_ddr_get_dimm_params() should be wrapped by
CONFIG_SYS_DDR_RAW_TIMING, otherwise, when using fixed_sdram() instead of
using SPD, it will cause compile error.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The fix for errata workaround is to avoid covering physical address
0xff000000 to 0xffffffff during the implementation. Early commit eb672e92
works until DDR size exceeds 4GB. This fix works for DDR size up to 64GB.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
* 'next' of git://git.denx.de/u-boot:
MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
doc: cleanup - move board READMEs into respective board directories
net: sh_eth: add support for SH7757's GETHER
net: sh_eth: modify the definitions of regsiter
net: sh_eth: add SH_ETH_TYPE_ condition
net: sh_eth: clean up for the SH7757's code
net: fec_mxc: Fix MDC for xMII
net: fec_mxc: Fix setting of RCR for xMII
net: nfs: make NFS_TIMEOUT configurable
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
cpu.c: In function ‘check_CPU’:
cpu.c:256:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Subject slightly changed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested on TQM855MDCBAB7-T66.102 (MPC855T at 66 MHz) and
TQM860LDB0A3-T50.202 (MPC860T at 50MHz).
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
An empty flush_dcache_range() was added into MPC83xx and MPC85xx to
work with drivers shared with other architecture. However, it is
compiled only if USB is set, but it is required for other drivers
(FSL_ESDHC), too.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Andy Fleming <afleming@gmail.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Marek Vasut <marex@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Added MPC83xx version.
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/mpc85xx: Fix Handling the lack of L2 cache on P2040/P2040E
powerpc/mpc85xx: Workaround for erratum CPU_A011
powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
powerpc/P4080: Check SVR for CPU22 workaround
lib/powerpc: addrmap_phys_to_virt() should return a pointer
powerpc/85xx: clean up P1022DS board configuration header file
powerpc/85xx: fdt_set_phy_handle() should return an error code
powerpc/85xx: minor clean-ups to the P2020DS board header file
powerpc/p1010rdb: add readme document for p1010rdb
powerpc/mpc85xx:NAND_SPL:Avoid IFC/eLBC Base address setting
powerpc/mpc85xx:Add debugger support for e500v2 SoC
powerpc/85xx:Fix NAND code base to support debugger
powerpc/85xx:Make debug exception vector accessible
powerpc/85xx:Fix MSR[DE] bit in MSR to support debugger
PATCH 1/4][v4] doc:Add documentation for e500 external debugger support
powerpc/p1010rdb: update mux config of p1010rdb board
powerpc/mpc85xx:Add BSC9131 RDB Support
powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
powerpc/85xx: Add USB device-tree fixup for various platforms
Signed-off-by: Wolfgang Denk <wd@denx.de>
Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.
Signed-off-by: York Sun <yorksun@freescale.com>
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.
Signed-off-by: York Sun <yorksun@freescale.com>
addrmap_phys_to_virt() converts a physical address (phys_addr_t) to a
virtual address, so it should return a pointer instead of an unsigned long.
Its counterpart, addrmap_virt_to_phys(), takes a pointer, so now they're
orthogonal.
The only caller of addrmap_phys_to_virt() converts the return value to
a pointer anyway.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
During NAND_SPL boot, base address and different register are programmed
default by corresponding NAND controllers(eLBC/IFC). These settings are
sufficient enough for NAND SPL.
Avoid updating these register.They will be programmed during NAND RAMBOOT.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG).
So define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.
Please refer doc/README.mpc85xx for more information
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Update NAND code base to ovecome e500 and e500v2's second limitation i.e. IVPR
+ IVOR15 should be valid fetchable OP code address.
As NAND SPL does not compile vector table so making sure IVOR + IVOR15 points to
any fetchable valid data
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Debugging of e500 and e500v1 processer requires debug exception vecter (IVPR +
IVOR15) to have valid and fetchable OP code.
1) While executing in translated space (AS=1), whenever a debug exception is
generated, the MSR[DS/IS] gets cleared i.e. AS=0 and the processor tries to
fetch an instruction from the debug exception vector (IVPR + IVOR15); since now
we are in AS=0, the application needs to ensure the proper TLB configuration to
have (IVOR + IVOR15) accessible from AS=0 also.
Create a temporary TLB in AS0 to make sure debug exception verctor is
accessible on debug exception.
2) Just after relocation in DDR, Make sure IVPR + IVOR15 points to valid opcode
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Debugging of e500 and e500v1 processer requires MSR[DE] bit to be set always.
Where MSR = Machine State register
Make sure of MSR[DE] bit is set uniformaly across the different execution
address space i.e. AS0 and AS1.
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Catalin Udma <catalin.udma@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
- BSC9131 is integrated device that targets Femto base station market.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
- BSC9130 is exactly same as BSC9131 except that the max e500v2
core and DSP core frequencies are 800M(these are 1G in case of 9131).
- BSC9231 is similar to BSC9131 except no MAPLE
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte shared
L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network acceleration
including IEEE 1588. v2 hardware support and virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single port)
and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
This patch takes care of code pertaining to power side functionality only.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
The misspelling of "semiconductor" causes some internal copyright analysis
tools to complain.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch conditionally defines flush_dcache_range() and
invalidate_dcache_range() on MPC8xxx, to avoid EHCI complaining,
resulting in the following output:
$ ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- ./MAKEALL MPC8572DS
Configuring for MPC8572DS board...
make: *** [u-boot] Error 1
powerpc-linux-gnu-size: './u-boot': No such file
e1000.c: In function ‘e1000_initialize’:
e1000.c:5264:13: warning: assignment from incompatible pointer type [enabled by default]
tsec.c: In function ‘tsec_initialize’:
tsec.c:638:12: warning: assignment from incompatible pointer type [enabled by default]
drivers/usb/host/libusb_host.o: In function `ehci_td_buffer':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:186: undefined reference to `flush_dcache_range'
drivers/usb/host/libusb_host.o: In function `ehci_submit_async':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:346: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:348: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:349: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:372: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:374: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:376: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:386: undefined reference to `invalidate_dcache_range'
make: *** [u-boot] Error 1
--------------------- SUMMARY ----------------------------
Boards compiled: 1
Boards with errors: 1 ( MPC8572DS )
----------------------------------------------------------
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Fix this:
ether_scc.c: In function 'mpc82xx_scc_enet_initialize':
ether_scc.c:377:14: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ether_fcc.c: In function 'fec_initialize':
ether_fcc.c:453:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ether_fcc.c: In function 'fec_initialize':
ether_fcc.c:390:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
fec.c: In function 'mpc8220_fec_recv':
fec.c:791:9: warning: passing argument 1 of 'NetReceive' discards qualifiers from pointer target type
include/net.h:438:13: note: expected 'uchar *' but argument is of type 'volatile uchar *'
fec.c: In function 'mpc8220_fec_initialize':
fec.c:839:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Commit db288a9 "net: Remove volatile from net API" caused a number of
build warnings:
fec.c: In function 'fec_initialize':
fec.c:183:13: warning: assignment from incompatible pointer type [enabled by default]
fec.c: In function 'fec_recv':
fec.c:284:5: warning: passing argument 1 of 'NetReceive' discards 'volatile' qualifier from pointer target type [enabled by default]
/home/wd/git/u-boot/work/include/net.h:433:13: note: expected 'uchar *' but argument is of type 'volatile uchar *'
scc.c: In function 'scc_initialize':
scc.c:85:14: warning: assignment from incompatible pointer type [enabled by default]
Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
* 'master' of git://git.denx.de/u-boot-nand-flash:
NAND: Remove ONFI detection message to from bootup log
driver/mtd:IFC: Fix possible memory leak
driver/mtd: IFC NAND: Add support of ONFI NAND flash
mtd, nand: move some printfs to debug output.
nand_util: correct YAFFS image write function
powerpc/85xx: fix NAND boot linker scripts for -fpic
nand: extend .raw accesses to work on multiple pages
GOT is now handled the way the main u-boot.lds does it. Without this,
the boot hangs when built with newer GCC (since 4.6). Older toolchains
hid the issue by converting -fpic to -fPIC.
Signed-off-by: Scott Wood <scottwood@freescale.com>
All arches init this the same way, so move the logic into the core
net code to avoid duplicating it everywhere else.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This field gets read in one place (by "bdinfo"), and we can replace
that with getenv("ipaddr"). After all, the bi_ip_addr field is kept
up-to-date implicitly with the value of the ipaddr env var.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The CCSR relocation code in start.S writes to MAS7 on all e500 parts, but
that register does not exist on e500v1.
Signed-off-by: Timur Tabi <timur@freescale.com>
When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.
Master needs to:
1. Set outbound SRIO windows in order to configure slave's registers
for the core's releasing.
2. Check the SRIO port status when release slave core, if no errors,
will implement the process of the slave core's releasing.
Slave needs to:
1. Set all the cores in holdoff by RCW.
2. Be powered on before master's boot.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ENV can be stored in master's memory space,
then slave can fetch the ENV through SRIO interface.
NOTE: Because the slave can not erase, write master's NOR flash by SRIO
interface, so it can not modify the ENV parameters stored in
master's NOR flash using "saveenv" or other commands.
Master needs to:
1. Put the slave's ENV into it's own memory space.
2. Set an inbound SRIO window covered slave's ENV stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode and ENV from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ucode can be stored in master's memory space,
then slave can fetch the ucode image through SRIO interface. For the
corenet platform, ucode is for Fman.
Master needs to:
1. Put the slave's ucode image into it's own memory space.
2. Set an inbound SRIO window covered slave's ucode stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.
The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure SRIO switch system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to SRIO1 or SRIO2 by RCW.
3. RCW should configure the SerDes, SRIO interfaces correctly.
4. Slave must be powered on after master's boot.
For the master module, need to finish these processes:
1. Initialize the SRIO port and address space.
2. Set inbound SRIO windows covered slave's u-boot image stored in
master's NOR flash.
3. Master's u-boot image should be generated specifically by
make xxxx_SRIOBOOT_MASTER_config
4. Master must boot first, and then slave can be powered on.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Currently "u-boot", the elf file generated via u-boot-nand.lds does not
contain required debug information i.e. .debug_{line, info, abbrev, aranges,
ranges} into their respective _global_ sections.
The original ld script line arch/powerpc/cpu/mpc85xx/start.o
KEEP(*(.bootpg)) is not entirely correct because the start.o file is already
processed by the linker,therefore the file wildcard in "KEEP(*(.bootpg))" will
not process start.o again for bootpg.
So Fix u-boot-nand.lds to generate these debug information.
Signed-off-by: Anmol Paralkar <b07584@freescale.com>
Signed-off-by: John Russo <John.Russo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
NAND SPL code never compile the vector table.
So no need to setup interrupt vector table for NAND SPL.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After relocation of vector table in SDRAM's lower address, IVORs value should
be updated with new handler addresses.
As vector tables are relocated to 0x100,0x200... 0xf00 address in DDR.IVORs
are updated with 0x100, 0x200,....f00 hard-coded values.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For e500 and e500v2 architecturees processor IVPR address should be alinged on
64K boundary.
in start.S, CONFIG_SYS_MONITOR_BASE is stored blindly in IVPR assuming it to be
64K aligned. It may not be true always. If it is not aligned, IVPR + IVORs may
not point to an exception handler.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func. This also fixes the build errors:
ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marex@denx.de>
These calls should not be made directly any more, since bootstage
will call the show_boot_...() functions as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than the caller negating our progress numbers to indicate an
error has occurred, which seems hacky, add a function to indicate this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This seems to be unsigned char for no good reason. Tidy this up and
remove the casts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Add support for fixing usb mode and phy type for
MPH(Multi Port Host) USB controllers in device-tree nodes.
Required for socs like P3060, P5020, etc having MPH USB controller
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Some code cleanup done for USB device-tree fixup:
- handling error value returned from fdt_fixup_usb_mode_phy_type()
- using ARRAY_SIZE macro
- using snprintf instead of sprintf
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
fsl_lbc: add printout of LCRR and LBCR to local bus regs
sbc8548: Fix up local bus init to be frequency aware
sbc8548: enable support for hardware SPD errata workaround
sbc8548: relocate fixed ddr init code to ddr.c file
sbc8548: Make enabling SPD RAM configuration work
sbc8548: Fix LBC SDRAM initialization settings
sbc8548: enable ability to boot from alternate flash
sbc8548: relocate 64MB user flash to sane boundary
Revert "SBC8548: fix address mask to allow 64M flash"
MPC85xxCDS: Fix missing LCRR_DBYP bits for 66-133MHz LBC
eXMeritus HWW-1U-1A: Add support for the AT24C128N I2C EEPROM
eXMeritus HWW-1U-1A: Minor environment variable tweaks
It can be handy to have these in the output when trying to
debug odd behaviour.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
In the current u-boot code, the value of these fields are the reserved
value (0b100), through the signal integrity measurement on freescale's
board with these reserved setting, the signal eye is out of the recommended
spec for non-transition amplitude at 500mV nominal.
According to the errata for MPC8379E, we should make a change to the
recommended setting from essentially nothing at this time to 0b001 for SATA.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We already flush the kernel image after we've loaded it to ensure
visiblity to the other cores. We need to do the same thing for the
ramdisk and device tree images. In AMP boot scenarios we might not be
HW cache coherent with the secondary core that we are loading and
setting the ramdisk and device tree up for. Thus we need to ensure
we've flushed the regions of memory utilized by ramdisk and device tree
so the loadding and any modifications (from decompression or fdt updates)
are made visible to the secondary cores.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Standard Debian powerpc and powerpcspe systems only include hard-float
libgcc in their native compilers, which causes scary build warnings when
building U-Boot.
Debian and other PowerPC-supporting distributions used to provide libgcc
and other libraries in a "nof" (soft-float) form in the "multilib"
packages. As they were completely unused by the distribution and
therefore tended to be very buggy it was decided to save some time on
the part of the maintainers and build-servers by removing them.
Admittedly, right now the linker warnings do not indicate any problems,
as the included routines do not use any floating point at all.
The concern is that if floating-point code were ever added it might
cause hard-float code to be unexpectedly included in U-Boot without
generating a hard error. This would cause unexplained crashes or
indeterminate results at runtime.
The easiest way to resolve this is to borrow the routines that U-Boot
needs from the Linux kernel, which has the same issue.
Specifically, the routines are: _ashldi3(), _ashrdi3(), and _lshrdi3().
They were borrowed from arch/powerpc/kernel/misc_32.S as of v2.6.38-rc5,
commit 85e2efbb1db9a18d218006706d6e4fbeb0216213, and are GPLv2+.
The Makefile framework was copied from the U-Boot ARM port.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Fix:
cpu.c: In function 'checkcpu':
cpu.c:51:7: warning: variable 'ver' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This adds support for the Freescale COM Express P2020 board. This board
is similar to the P1_P2_RDB, but has some extra (as well as missing)
peripherals.
Unlike all other mpc85xx boards, it uses a watchdog timeout to reset.
Using the HRESET_REQ register does not work.
This board has no NOR flash, and can only be booted via SD or SPI. This
procedure is documented in Freescale Document Number AN3659 "Booting
from On-Chip ROM (eSDHC or eSPI)." Some alternative documentation is
provided in Freescale Document Number P2020RM "P2020 QorIQ Integrated
Processor Reference Manual" (section 4.5).
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
interactive.c: In function 'fsl_ddr_interactive':
interactive.c:1357:15: warning: variable 'len' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is useful for boards which cannot be reset in the usual way for the
85xx CPU. An example is a board which can only be reset by a hardware
watchdog.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The localbus controller node in the device tree is typically a root node,
even though the controller is part of CCSR. If we were to put the lbc
node under the SOC node, then the 'ranges' property in the lbc node would
translate through the 'ranges' property of the parent SOC node, and we
don't want that.
Since the lbc is a separate node, it's possible for the 'reg' property to
be wrong. This happened with the original version of p1022ds.dts, which
used a 32-bit value in the 'reg' address, instead of a 36-bit address.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Newer JEDEC DDR3 SPD Specifications define several additional values for
the DDR3 module_type field which were undefined when this code was
written. Update the code to handle the newer module types.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Several macros are used to identify and locate the microcode binary image
that U-boot needs to upload to the QE or Fman. Both the QE and the Fman
use the QE Firmware binary format to package their respective microcode data,
which is why the same macros are used for both. A given SOC will only have
a QE or an Fman, so this is safe.
Unfortunately, the current macro definition and usage has inconsistencies.
For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman
firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address
of NAND. There's no way to know by looking at a variable how it's supposed
to be used.
In the future, the code which uploads QE firmware and Fman firmware will
be merged.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the P1022/P1013, the work-around for erratum SATA_A001 was implemented
only if U-Boot initializes SATA, but SATA is not initialized by default. So
move the work-around to the CPU initialization function, so that it's always
executed on the SOCs that need it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA
controller, so it should be defined in config_mpc85xx.h instead of the various
board header files. So now CONFIG_FSL_SATA_V2 is always defined on the P1013,
P1022, P2041, P3041, P5010, and P5020. It was already defined for the
P1010 and P1014.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum A-003474: Internal DDR calibration circuit is not supported
Impact:
Experience shows no significant benefit to device operation with
auto-calibration enabled versus it disabled. To ensure consistent timing
results, Freescale recommends this feature be disabled in future customer
products. There should be no impact to parts that are already operating
in the field.
Workaround:
Prior to setting DDR_SDRAM_CFG[MEM_EN]=1, do the following:
1. Write a value of 0x0000_0015 to the register at offset
CCSRBAR + DDR OFFSET + 0xf30
2. Write a value of 0x2400_0000 to the register at offset
CCSRBAR + DDR OFFSET + 0xf54
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the fixup matchable with dts and kernel. Update the compatible from
"fsl,flexcan-v1.0" to "fsl,p1010-flexcan" and Change the "clock-freq"
property to "clock-frequency". We also change flexcan frequency from
CCB-clock to CCB-clock/2 according to P1010 spec.
We now keep the old interfaces to make previous kernel work. They should
be removed in the future.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum A-003999: Running Floating Point instructions requires special
initialization.
Impact:
Floating point arithmetic operations may result in an incorrect value.
Workaround:
Perform a read modify write to set bit 7 to a 1 in SPR 977 before
executing any floating point arithmetic operation. This bit can be set
when setting MSR[FP], and can be cleared when clearing MSR[FP].
Alternatively, the bit can be set once at boot time, and never cleared.
There will be no performance degradation due to setting this bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Configuring for sbc8349 board...
spd_sdram.c: In function 'spd_sdram':
spd_sdram.c:152:41: warning: variable 'trfc_high' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fix:
iop480_uart.c: In function 'serial_init':
iop480_uart.c:137:16: warning: variable 'val' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
40x_spd_sdram.c: In function 'spd_sdram':
40x_spd_sdram.c:137:6: warning: variable 'sdram0_b3cr' set but not used [-Wunused-but-set-variable]
40x_spd_sdram.c:136:6: warning: variable 'sdram0_b2cr' set but not used [-Wunused-but-set-variable]
40x_spd_sdram.c:129:6: warning: variable 'sdram0_ecccfg' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
44x_spd_ddr2.c: In function 'initdram':
44x_spd_ddr2.c:450:17: warning: variable 'dimm_spd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c: In function 'program_copt1':
44x_spd_ddr2.c:1003:16: warning: variable 'ddrtype' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c: In function 'DQS_calibration_process':
44x_spd_ddr2.c:2498:7: warning: variable 'window_found' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2497:16: warning: variable 'end_rffd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2496:16: warning: variable 'end_rqfd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2495:16: warning: variable 'begin_rffd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2494:16: warning: variable 'begin_rqfd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2493:7: warning: variable 'min_end' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
44x_spd_ddr.c: In function 'program_cfg0':
44x_spd_ddr.c:384:16: warning: variable 'dimm_64bit' set but not used [-Wunused-but-set-variable]
44x_spd_ddr.c:383:16: warning: variable 'dimm_32bit' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
cmd_ecctest.c: In function 'inject_ecc_error':
cmd_ecctest.c:116:6: warning: variable 'val' set but not used [-Wunused-but-set-variable]
cmd_ecctest.c: In function 'rewrite_ecc_parity':
cmd_ecctest.c:154:6: warning: variable 'val' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
4xx_ibm_ddr2_autocalib.c: In function 'get_membase':
4xx_ibm_ddr2_autocalib.c:157:8: warning: variable 'bxcf' set but not used [-Wunused-but-set-variable]
4xx_ibm_ddr2_autocalib.c: In function 'DQS_calibration_methodB':
4xx_ibm_ddr2_autocalib.c:722:8: warning: variable 'rffd' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
4xx_pcie.c: In function 'pcie_read_config':
4xx_pcie.c:230:6: warning: variable 'address' set but not used [-Wunused-but-set-variable]
4xx_pcie.c: In function 'pcie_write_config':
4xx_pcie.c:290:6: warning: variable 'address' set but not used [-Wunused-but-set-variable]
4xx_pcie.c: In function 'ppc4xx_setup_pcie_rootpoint':
4xx_pcie.c:1066:17: warning: variable 'rmbase' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
usb_ohci.c: In function 'dl_transfer_length':
usb_ohci.c:756:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
i2c.c: In function 'wait_for_bb':
i2c.c:81:16: warning: variable 'temp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
pci.c: In function 'pci_init_board':
pci.c:55:26: warning: variable 'pci_conf' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
* 'master' of git://git.denx.de/u-boot-video:
api: export LCD device to external apps
font: split font data from video_font.h
tools: logo: split bmp arrays from bmp_logo.h
lcd: add clear and draw bitmap declaration
VIDEO: mx3fb: GCC4.6 fix build warnings
Powerpc/DIU: Fixed the 800x600 and 1024x768 resolution bug
While video_font.h is useful even without referencing the font data, it
is not possible to be included multiple times because it defines font
data array right in the header.
This patch splits the font data array into video_font_data.h and so now
video_font.h can be included multiple times. This at least solves the
code duplication in board/mcc200/lcd.c.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Remove symbolic link generated by compiling. Fix makefile for out-of-tree
compiling error.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fix:
ctrl_regs.c: In function 'set_ddr_sdram_cfg_2':
ctrl_regs.c:641:15: warning: variable 'rcw_en' set but not used [-Wunused-but-set-variable]
ctrl_regs.c: In function 'compute_fsl_memctl_config_regs':
ctrl_regs.c:951:31: warning: array subscript is above array bounds [-Warray-bounds]
ctrl_regs.c:752:34: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
fsl_corenet_serdes.c: In function 'fsl_serdes_init':
fsl_corenet_serdes.c:511:8: warning: variable 'buf' set but not used [-Wunused-but-set-variable]
fsl_corenet_serdes.c:498:18: warning: variable 'lane_prtcl' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
options.c: In function 'populate_memctl_options':
options.c:486:28: warning: variable 'pdodt' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
fsl_lbc.c: In function 'upmconfig':
fsl_lbc.c:110:9: warning: variable 'mdr' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
tlb.c: In function 'disable_tlb':
tlb.c:175:34: warning: variable '_mas7' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
cpu_init.c: In function 'cpu_init_r':
cpu_init.c:320:7: warning: variable 'l2srbar' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wrong pointer was being used to copy code into L2SRAM.
Also removed the unreferenced variable l2srbar.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A few of the config registers changed definition between MMU v1.0 and
MMUv2.0. The new e6500 core from Freescale implements v2.0 of the
architecture.
Specifically, how we determine the size of TLB entries we support in the
variable size (or TLBCAM/TLB1) array is specified in a new register
(TLBnPS - TLB n Page size) instead of via TLBnCFG.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix USB device-fixup warning "node not found". This was occuring
because of static nature of start_offset variable
Static start_offset was storing offset of last node modified, and
was becoming issue if node fixup is carried multiple times,
resulting in "node not found" warning
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On some Freescale systems (e.g. those booted from the on-chip ROM), the
TLB that covers the boot page can also cover CCSR, which breaks the CCSR
relocation code. To fix this, we resize the boot page TLB so that it only
covers the 4KB boot page.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Verify that CCSR is actually located where it is supposed to be before
we relocate it. This is useful in detecting U-Boot configurations that
are broken (e.g. an incorrect value for CONFIG_SYS_CCSRBAR_DEFAULT).
If the current value is wrong, we enter an infinite loop, which is handy
for debuggers.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Calls to tlbwe and tlbsx should be preceded with an isync/msync pair.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some of the MAS register macros do not protect the parameter with
parentheses, which could cause wrong values if the parameter includes
operators.
Also fix the definition of TSIZE_TO_BYTES() so that it actually uses
the parameter. This hasn't caused any problems to date because the
parameter was always been 'tsize'.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.
Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
spi.c: In function 'spi_init_r':
spi.c:279:22: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
spi.c: In function 'spi_xfer':
spi.c:361:22: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
bat_rw.c: In function 'write_bat':
bat_rw.c:38:6: warning: variable 'batn' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andy Fleming <afleming@gmail.com>
Fix:
i2c.c: In function 'wait_for_bb':
i2c.c:109:16: warning: variable 'temp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This also fixes some GCC 4.6 build warnings like:
i2c.c: In function 'i2c_init':
i2c.c:221:26: warning: variable 'txbd' set but not used
[-Wunused-but-set-variable]
i2c.c:221:19: warning: variable 'rxbd' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Make (mostly) checkpatch clean (don't convert to use I/O accessors
yet, so there will be "Use of volatile is usually wrong" warnings
left. Also accept some other harmless checkpatch warnings.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Fix:
fec.c: In function 'mpc8220_fec_recv':
fec.c:733:8: warning: variable 'frame' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
speed.c: In function 'get_clocks':
speed.c:113:30: warning: variable 'cpmdf' set but not used
[-Wunused-but-set-variable]
speed.c:113:23: warning: variable 'busdf' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
spi.c: In function 'spi_init_f':
spi.c:144:21: warning: variable 'iop' set but not used
[-Wunused-but-set-variable]
spi.c:142:22: warning: variable 'cpi' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
This also fixes some GCC 4.6 build warnings like:
warning: variable 'txbd' set but not used [-Wunused-but-set-variable]
warning: variable 'rxbd' set but not used [-Wunused-but-set-variable]
Signed-off-by: WOlfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Make (mostly) checkpatch-clean
We don't acctually change the code (like convert to use I/O
accessors), so there will be some remaining "Use of volatile"
warnings from checkpatch.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Fix:
cpu.c: In function 'check_CPU':
cpu.c:188:8: warning: variable 'mid' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
fec.c: In function 'fec_pin_init':
fec.c:381:18: warning: variable 'fecp' set but not used
[-Wunused-but-set-variable]
fec.c: In function 'fec8xx_miiphy_write':
fec.c:1013:8: warning: variable 'rdreg' set but not used
[-Wunused-but-set-variable]
Note: The code was slightly rearranged, but no functional changes
attempted, i. e. no conversion to use I/O accessors.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
usb_ohci.c: In function 'dl_transfer_length':
usb_ohci.c:751:8: warning: variable 'tdINFO' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
CodingStyle cleanup.
Accepted (in this cleanup) checkpatch messages:
- externs should be avoided
(to be cleaned up later)
- no spaces at the start of a line
(accepted in multi-line #if's)
- Macros with complex values
(false reports)
- do not use assignment in if condition
(accepted in one place, where avoiding it would have required an
additional level of nesting, resulting in less readable code)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
i2c.c: In function 'wait_for_bb':
i2c.c:104:16: warning: variable 'temp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Added siprr_{b,c} and sepcr for completeness.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The byte address distance between GTCFR2 and GTMDR1 is 11, not 10.
Reported-by: Shawn Bai <programassem@hotmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
U-Boot Makefiles contain a number of tests for compiler features etc.
which so far are executed again and again. On some architectures
(especially ARM) this results in a large number of calls to gcc.
This patch makes sure to run such tests only once, thus largely
reducing the number of "execve" system calls.
Example: number of "execve" system calls for building the "P2020DS"
(Power Architecture) and "qong" (ARM) boards, measured as:
-> strace -f -e trace=execve -o /tmp/foo ./MAKEALL <board>
-> grep execve /tmp/foo | wc -l
Before: After: Reduction:
==================================
P2020DS 20555 15205 -26%
qong 31692 14490 -54%
As a result, built times are significantly reduced, typically by
30...50%.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Albert Aribaud <albert.aribaud@free.fr>
cc: Graeme Russ <graeme.russ@gmail.com>
cc: Mike Frysinger <vapier@gentoo.org>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Matthias Weisser <weisserm@arcor.de>
Tested-by: Sanjeev Premi <premi@ti.com>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Macpaul Lin <macpaul@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Fix:
4xx_pci.c: In function 'pci_init_board':
4xx_pci.c:855:6: warning: variable 'busno' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Fix:
4xx_uart.c: In function 'get_serial_clock':
4xx_uart.c:204:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Commit 1272592 "powerpc: Use getenv_ulong() in place of getenv(),
strtoul" instroduced a build warning for some PPC systems:
board.c: In function 'board_init_r':
board.c:626: warning: unused variable 's'
Fix it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
interrupts.c: In function 'interrupt_init_cpu':
interrupts.c:62: warning: format '%d' expects type 'int', but argument 2 has
type 'long unsigned int'
interrupts.c:69: warning: format '%x' expects type 'unsigned int', but argument
2 has type 'volatile uint *'
interrupts.c:72: warning: format '%x' expects type 'unsigned int', but argument
2 has type 'volatile uint *'
interrupts.c:75: warning: format '%x' expects type 'unsigned int', but argument
2 has type 'volatile uint *'
interrupts.c:79: warning: format '%x' expects type 'unsigned int', but argument
2 has type 'volatile uint *'
interrupts.c:83: warning: format '%x' expects type 'unsigned int', but argument
2 has type 'volatile uint *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
ddr1_dimm_params.c: In function 'compute_ranksize':
ddr1_dimm_params.c:44: warning: format '%08x' expects type 'unsigned int', but
argument 2 has type 'long long unsigned int'
ddr2_dimm_params.c: In function 'compute_ranksize':
ddr2_dimm_params.c:43: warning: format '%08x' expects type 'unsigned int', but
argument 2 has type 'long long unsigned int'
ddr3_dimm_params.c: In function 'compute_ranksize':
ddr3_dimm_params.c:74: warning: format '%16lx' expects type 'long unsigned int',
but argument 2 has type 'long long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
4xx_pcie.c: In function 'pcie_read_config':
4xx_pcie.c:268: warning: format '%08x' expects type 'unsigned int', but argument
3 has type 'volatile unsigned char *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
4xx_ibm_ddr2_autocalib.c: In function 'DQS_calibration_methodB':
4xx_ibm_ddr2_autocalib.c:910: warning: format '%08X' expects type 'unsigned
int', but argument 2 has type 'ulong'
4xx_ibm_ddr2_autocalib.c:911: warning: format '%08X' expects type 'unsigned
int', but argument 2 has type 'ulong'
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
4xx_ibm_ddr2_autocalib.c:1217: warning: format '%08x' expects type 'unsigned
int', but argument 2 has type 'ulong'
4xx_ibm_ddr2_autocalib.c:1230: warning: format '%08x' expects type 'unsigned
int', but argument 2 has type 'ulong'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
44x_spd_ddr.c: In function 'program_tr0':
44x_spd_ddr.c:823: warning: format '%x' expects type 'unsigned int', but
argument 2 has type 'long unsigned int'
44x_spd_ddr.c: In function 'program_tr1':
44x_spd_ddr.c:1054: warning: format '%x' expects type 'unsigned int', but
argument 2 has type 'long unsigned int'
44x_spd_ddr.c: In function 'program_bxcr':
44x_spd_ddr.c:1127: warning: format '%d' expects type 'int', but argument 2 has
type 'long unsigned int'
44x_spd_ddr.c:1196: warning: format '%d' expects type 'int', but argument 2 has
type 'long unsigned int'
44x_spd_ddr.c:1196: warning: format '%d' expects type 'int', but argument 3 has
type 'long unsigned int'
44x_spd_ddr.c:1196: warning: format '%d' expects type 'int', but argument 4 has
type 'long unsigned int'
44x_spd_ddr.c:1196: warning: format '%d' expects type 'int', but argument 5 has
type 'long unsigned int'
44x_spd_ddr.c:1242: warning: format '%d' expects type 'int', but argument 2 has
type 'long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
denali_spd_ddr2.c: In function 'get_spd_info':
denali_spd_ddr2.c:363: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c: In function 'check_frequency':
denali_spd_ddr2.c:390: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c: In function 'get_dimm_size':
denali_spd_ddr2.c:473: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:474: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:475: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:476: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c: In function 'program_ddr0_03':
denali_spd_ddr2.c:571: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:604: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:604: warning: format '%d' expects type 'int', but argument 3
has type 'long unsigned int'
denali_spd_ddr2.c:643: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:644: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:645: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:646: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:676: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c: In function 'program_ddr0_04':
denali_spd_ddr2.c:731: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:733: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:735: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c: In function 'program_ddr0_05':
denali_spd_ddr2.c:772: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:774: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c: In function 'program_ddr0_06':
denali_spd_ddr2.c:831: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:833: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c: In function 'program_ddr0_11':
denali_spd_ddr2.c:860: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c: In function 'program_ddr0_26':
denali_spd_ddr2.c:931: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c:933: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c: In function 'program_ddr0_27':
denali_spd_ddr2.c:944: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c: In function 'program_ddr0_43':
denali_spd_ddr2.c:978: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_spd_ddr2.c: In function 'program_ddr0_44':
denali_spd_ddr2.c:1006: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
denali_data_eye.c: In function
'denali_core_search_data_eye':denali_spd_ddr2.c:646: warning: format '%d'
expects type 'int', but argument 2 has type 'long unsigned int'
denali_data_eye.c:320: warning: format '%08lx' expects type 'long unsigned int',
but argument 2 has type 'u32'
denali_data_eye.c:330: warning: format '%08lx' expects type 'long unsigned int',
but argument 2 has type 'u32'
denali_spd_ddr2.c:676: warning: format '%d' expects type 'int', but argument 2
has type 'long unsigned int'
denali_data_eye.c:340: warning: format '%08lx' expects type 'long unsigned int',
but argument 2 has type 'u32'
denali_data_eye.c:350: warning: format '%08lx' expects type 'long unsigned int',
but argument 2 has type 'u32'
denali_data_eye.c:360: warning: format '%08lx' expects type 'long unsigned int',
but argument 2 has type 'u32'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
serial.c: In function 'serial_setbrg_dev':
serial.c:143: warning: format '%d' expects type 'int', but argument 4 has type
'long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Commit 1272592 introduced a warning since the variable 's' is no longer
always used, depending on the CONFIG options.
Signed-off-by: Simon Glass <sjg@chromium.org>
The call to run_post(POST_ROM) which can run the POST memory test
is currently called too late when gd has already been copied to DRAM.
This results in failure to boot Linux after a POST_ROM memory test
tested all RAM while gd was already relocated to DRAM due to gd being
overwritten by the POST_ROM memory test.
Support this by moving the call to run_post(POST_ROM) to run earlier,
before U-Boot has started to move data to DRAM (from late board_init_f
to early board_init_f) where DRAM is initialized, but not used yet.
This allows that an POST memory test can test the whole DRAM,
including the area where the board info struct is located.
Signed-off-by: Bernhard Kaindl <bernhard.kaindl@thalesgroup.com>
Cc: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl>
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
To ease the implementation of other MPC85xx board ports, several common
GPIO helpers are added to <asm/mpc85xx_gpio.h>.
Since each of these compiles to no more than 4-5 instructions it would
be very inefficient to call them out of line, therefore we put them
entirely in the header file.
The HWW-1U-1A board port which these were written for strongly prefers
to set multiple GPIOs as a single batch operation, so the API is
designed around that basis.
To assist other board ports, a small set of wrappers are used which
provides a standard gpio_request() interface around the MPC85xx-specific
functions. This can be enabled with CONFIG_MPC85XX_GENERIC_GPIO
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The work-around for P4080 erratum SERDES9 says that the SERDES receiver
lanes should be reset after the XAUI starts tranmitting alignment signals.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For P3060 and P4080, USB pins are multiplexed with other functions.
Update the device tree status for USB ports based on setting of
RCW[EC1] & RCW[EC2] which describe if pins are muxed to usb.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch is intended to initialize RMan LIODN related registers on
P2041, P304S and P5020 SocS. It also adds the "rman@0" child node to
qman-portal nodes, adds "fsl,liodn" property to RMan inbound block nodes.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update device tree handling for SRIO controller to support updated
fsl,srio device tree binding.
We handle disabling of individual ports, the whole controller, RMU, and
RMAN. Additionally, we setup the SRIO related LIODNs in the device
tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Properly set the LIODN values associated with SRIO controller. On
P4080/P3060 we have an LIODN per port and one for the RMU. On
P2041/P3041/P5020 we have 2 LIODNs per port.
Update the tables for all of these devices to properly handle both
styles.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-fdt:
powerpc/85xx: use fdt_create_phandle() to create the Fman firmware phandles
fdt: update fdt_alloc_phandle to use fdt_get_phandle
fdt: check for fdt errors in fdt_create_phandle
fdt: Add a do_fixup_by_path_string() function
Function fdt_create_phandle() conveniently creates new phandle properties
using both "linux,phandle" and "phandle", so it should be used by all code
that wants to create a phandle.
The Fman firmware code, which embeds an Fman firmware into the device tree,
was creating the phandle properties manually. Instead, change it to use
fdt_create_phandle().
Signed-off-by: Timur Tabi <timur@freescale.com>
The EC1_EXT, EC2_EXT, and EC3 bits in the RCW don't officially exist on the
P3060 and should always be set to zero.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P3041 has 10 qman portals, we need to configure all of them:
* As there are only 4 physical cores sdest can only be 0 to 3
* We assign dqrr & frame data LIODNs for all portals so if they
are utilized the proper mapping tables can be setup uniquely
(PAMU stashing)
* We set Portal 6-10 to LIODN offsets 1-5 as the global LIODN
assignments are tuned around an assumption of at most 5
partitions.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2041 has 10 qman portals, we need to configure all of them:
* As there are only 4 physical cores sdest can only be 0 to 3
* We assign dqrr & frame data LIODNs for all portals so if they
are utilized the proper mapping tables can be setup uniquely
(PAMU stashing)
* We set Portal 6-10 to LIODN offsets 1-5 as the global LIODN
assignments are tuned around an assumption of at most 5
partitions.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P5020 has 10 qman portals, we need to configure all of them:
* As there are only 2 physical cores sdest can only be 0 or 1
* We assign dqrr & frame data LIODNs for all portals so if they
are utilized the proper mapping tables can be setup uniquely
(PAMU stashing)
* We set Portal 6-10 to LIODN offsets 1-5 as the global LIODN
assignments are tuned around an assumption of at most 5
partitions.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. The SD_DATA[4:7] signals are shared with the SPI chip selects on 8536DS,
so don't set MPC85xx_PMUXCR_SD_DATA that config eSDHC data bus-width
to 4-bit and enable SPI signals.
2. Add eSPI controller and SPI-FLASH definition.
Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We really shouldn't be overwriting bat registers with translation enabled,
especially when we're executing code using one of them for translating
the current instruction stream. Instead, disable address translation
while doing the final BAT setup.
In order to do this, setup_bats has to move back to asm code, because we
require translation to be enabled to have a stack for C code. The yucky
thing about that is that the assembler doesn't like ULL so we have to
switch to using HIGH/LOW pairs for physical addresses that are > 32 bits
in length.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Function dtsec_configure_serdes() needs to know where the TBI PHY registers
are in order to configure SGMII for proper SerDes operation.
During SGMII initialzation, fm_eth_init_mac() passing NULL for 'phyregs'
when it called init_dtsec(), because it was believed that phyregs was not
used. In fact, it is used by dtsec_configure_serdes() to configure the TBI
PHY registers.
We also need to define the PHY registers in struct fm_mdio.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Interactive DDR debugging provides a user interface to view and modify SPD,
DIMM parameters, board options and DDR controller registers before DDR is
initialized. With this feature, developers can fine-tune DDR for board
bringup and other debugging without frequently having to reprogram the flash.
To enable this feature, define CONFIG_FSL_DDR_INTERACTIVE in board header
file and set an environment variable to activate it. Syntax:
setenv ddr_interactive on
After reset, U-boot prompts before initializing DDR controllers
FSL DDR>
The available commands are
print print SPD and intermediate computed data
reset reboot machine
recompute reload SPD and options to default and recompute regs
edit modify spd, parameter, or option
compute recompute registers from current next_step to end
next_step shows current next_step
help this message
go program the memory controller and continue with u-boot
The first command should be "compute", which reads data from DIMM SPDs and
board options, performs the calculation then stops before setting DDR
controller. A user can use "print" and "edit" commands to view and modify
anything. "Go" picks up from current step with any modification and
compltes the calculation then enables the DDR controller to continue u-boot.
"Recompute" does it over from fresh reading.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is long over due. All but two net drivers have been converted, but
those have now been dropped.
The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined. So here we scrub the
core code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This pushes the ugly duplicated arch ifdef lists we maintain in various
image related files out to the arch headers themselves.
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current post_log_word in global data is currently split into 2x
16 bits: half for the test start, half for the test success.
Since we alredy have more than 16 POST tests defined and more could
be defined, this may result in an overflow and the post_output_backlog
would not work for the tests defined further of these 16 positions.
An additional field is added to global data so that we can now support up
to 32 (depending of architecture) tests. The post_log_word is only used
to record the start of the test and the new field post_log_res for the
test success (or failure). The post_output_backlog is for this change
also adapted.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Allow redirection of console output prior to console initialisation to a
temporary buffer.
To enable this functionality, the board (or arch) must define:
- CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer
- CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer
- CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes)
The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes
Any earlier characters are silently dropped.
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Add P3060 SoC specific information:cores setup, LIODN setup, etc
The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for Job Queue/Ring LIODN for the RAID Engine on P5020. Each
Job Queue/Ring combo needs one id assigned for a total of 4 (2 JQs/2
Rings per JQ). This just handles RAID Engine in non-DPAA mode.
Signed-off-by: Santosh Shukla <santosh.shukla@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].
Refer to the erratum LBIU3 of mpc8548.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some
early version silicons. The default settings of the DDR IO receiver
biasing may not work at cold temperature. When a failure occurs,
a DDR input latches an incorrect value. The workaround will set the
receiver to an acceptable bias point.
Signed-off-by: Gong Chen
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
(Please note that ISBC expects all these addresses, images to be
validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
at 0xcffffffc.
Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
(The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
created by PBL/configuration word within 0 - 3.5G memory range. The
u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
PBL/configuration word after switch to AS = 1
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Acked-by: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The EST SBC8260 is over 10 years old, and the SBC8240 older than
that. With the tiny amount of RAM (by today's standards), there
really isn't anyone interested in running the latest U-boot on
these EOL products anymore.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: jon.diekema@smiths-aerospace.com
There are some locations in the code which anticipate printf() being called
before the console is ready by squelching printf() on gd->have_console.
Move this squelching into printf(), vprintf(), puts() and putc(). Also
make tstc() and getc() return 0 if console is not yet initialised
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes advantage of
overall improvement. It requires changes for board files to customize
platform-dependent parameters.
To utilize the unified DDR driver, a board needs to define CONFIG_FSL_DDRx
in the header file. No more boards will be accepted without such definition.
Note: the workaround for erratum DDR6 for the very old MPC834x Rev 1.0/1.1
and MPC8360 Rev 1.1/1.2 parts is not migrated to unified driver.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DDR2 has different ODT table and values. Adding table according to Samsung
application note.
Fix additive latency calculation to avoid interger underflow.
Also converted typedef dynamic_odt_t to struct dynamic_odt.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The two slots on the same controller have different addresses.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Check second DIMM slot in case the first one is empty.
Honor DQS enable option for SDRAM mode register.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DDR RCW varies at different speeds. It is common for all platform. Move it
out from corenet_ds.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Extend CAS write Latency (CWL) table to comply with DDR3 spec
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8536 seems to use only 3 bits for the major revision field in the
SVR rather than the 4 bits used by all other processors. The most
significant bit is used as a mfg code on MPC8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 has two 1G ethernet controllers the first can run in
SGMII, RGMII, or RMII. The second can only do SGMII & RGMII.
We need to setup a for SoC & board registers based on our various
configuration for ethernet to function properly on the board.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block. Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman). However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.
Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely. This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.
Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.
We add support for the following SoCs:
* P1023 - 1 Fman, 2x1g
* P4080 - 2 Fman, each Fman has 4x1g and 1x10g
* P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some SOCs have discontiguously-numbered cores, and so we can't determine the
valid core numbers via the FRR register any more. We define
CPU_TYPE_ENTRY_MASK to specify a discontiguous core mask, and helper functions
to process the mask and enumerate over the set of valid cores.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The old fdt_create_phandle didn't actually create a phandle it just
set one. We'll introduce a new helper that actually does creation.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Add ifdef protection around fman specific code related to device tree
clock setup. If we dont have CONFIG_SYS_DPAA_FMAN defined we shouldn't
be executing this code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue: Address masking doesn't work properly.
When sum of the base address, defined by BA, and memory bank size,
defined by AM, exceeds 4GB (0xffff_ffff) then AMASKn[AM] doesn't mask
CSPRn[BA] bits.
Impact:
This will impact booting when we are reprogramming CSPR0(BA) and
AMASK0(AMASK) while executing from NOR Flash.
Workaround:
Re-programming of CSPR(BA) and AMASK is done while not executing from NOR
Flash. The code which programs the BA and AMASK is executed from L2-SRAM.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue:
Peripheral connected to IFC_CS3 may hamper booting from IFC.
Impact:
Boot from IFC may not be successful if IFC_CS3 is used.
Workaround:
If IFC_CS3 is used, gate IFC_CS3 while booting from NAND or NOR.
Also Software should select IFC_CS3 using PMUXCR[26:27] = 0x01.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue:
The NOR-FCM does not support access to unaligned addresses for 16 bit port size
Impact:
When 16 bit port size is used, accesses not aligned to 16 bit address boundary
will result in incorrect data
Workaround:
The workaround is to switch to GPCM mode for NOR Flash access.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For an IFC Erratum (A-003399) we will need to access IFC registers in
cpu_init_early_f() so expand the TLB covering CCSR to 1M.
Since we need a TLB to cover 1M we move to using TLB1 array for all the
early mappings so we can cover various sizes beyond 4k.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add NAND support (including spl) on IFC, such as is found on the p1010.
Note that using hardware ECC on IFC with small-page NAND (which is what
comes on the p1010rdb reference board) means there will be insufficient
OOB space for JFFS2, since IFC does not support 1-bit ECC. UBI should
work, as it does not use OOB for anything but ECC.
When hardware ECC is not enabled in CSOR, software ECC is now used.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
[scottwood@freescale.com: ECC rework and misc fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Before main memory (DDR) is initialized, the on-chip L1 cache is used as a
memory area for the stack and the global data (gd_t) structure. This is
called the initial RAM area, or initram. The L1 cache is locked and the TLBs
point to a non-existent address (so that there's no chance it will overlap
main memory or any device). The L1 cache is also configured not to write
out to memory or the L2 cache, so everything stays in the L1 cache.
One of the things we might do while running out of initram is relocate CCSR.
On reset, CCSR is typically located at some high 32-bit address, like
0xfe000000, and this may not be the best place for CCSR. For example, on
36-bit systems, CCSR is relocated to 0xffe000000, near the top of 36-bit
memory space.
On some future Freescale SOCs, the L1 cache will be forced to write to the
backing store, so we can no longer have the TLBs point to non-existent address.
Instead, we will point the TLBs to an unused area in CCSR. In order for this
technique to work, CCSR needs to be relocated before the initram memory is
enabled.
Unlike the original CCSR relocation code in cpu_init_early_f(), the TLBs
we create now for relocating CCSR are deleted after the relocation is finished.
cpu_init_early_f() will still need to create a TLB for CCSR (at the new
location) for normal U-Boot purposes. This is done to keep the impact to
existing U-Boot code minimal and to better isolate the CCSR relocation code.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.
CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file. Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.
CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.
Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot). All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.
README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
- Use both getenv() and hwconfig to get USB phy type till getenv()
is depricated
- Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
has internal UTMI phy
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Flush the dcache before removing the TLB with caches enabled.
Otherwise this might lead to problems later on, e.g. while booting
Linux (as seen on ICON-440SPe).
Signed-off-by: Stefan Roese <sr@denx.de>
Change bd_t->bi_phy* arrays from 1 to 2 for PPC405EX since
405EX has 2 ethernet interfaces.
Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Since we are loading an executable image into memory we need flush it
out of the cache to possible maintain coherence on CPUs with split
instruction and data caches. We do this for other executable image
loading command.
On PowerPC once we do this we no longer need to explicitly flush the
dcache on multi-core systems in the BOOTM_STATE_OS_PREP phase. We now
treat the BOOTM_STATE_OS_PREP as a no-op to maintain backwards
compatibility with the bootm subcommand.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Diana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
The U-Boot Design Principles[1] clearly say:
Initialize devices only when they are needed within U-Boot, i.e. don't
initialize the Ethernet interface(s) unless U-Boot performs a download
over Ethernet; don't initialize any IDE or USB devices unless U-Boot
actually tries to load files from these, etc. (and don't forget to
shut down these devices after using them - otherwise nasty things may
happen when you try to boot your OS).
So, do not initialize and read the sensors on startup.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Holger Brunck <holger.brunck@keymile.com>
The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board.
This device only supports 800x600 resolution, so if that resolution is selected,
assume that this is the device. The device is attached to the LVDS port
on the P1022DS board.
The existing 800x600 entry (for the PDM360NG board) is actually 800x480,
so we fix that. To support two different 800x resolutions, the Y-resolution
is now passed to fsl_diu_init() and both values are used to pick the proper
fb_videomode structure.
The data for the 800x600 video mode is originally from Jiang Yutang.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
We used <usb.h> for USB_MAX_DEVICE. However this requires we actual
build in support for USB into u-boot (which should not be required for
device tree fixup).
At this time no FSL SoC that utilizies this code (83xx/85xx) has more
than 2 USB controllers. So we replace USB_MAX_DEVICE with a local
define FSL_MAX_NUM_USB_CTRLS.
If/when a device shows up with more than 2 controllers we can easily
bump this value or refactor into a proper define per SoC.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to
'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break
out if it cannot find 'usb1', so drop the 'else' clause to make driver scan
all the 'usbx'.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce ft_verify_fdt(), a function that is called after the device tree
has been fixed up, that displays warning messages if there is a mismatch
between the physical addresses of some devices that U-Boot has configured
with what the device tree says the addresses are.
This is a particular problem when booting a 36-bit device tree from a
32-bit U-Boot (or vice versa), because the physical address of CCSR is
wrong in the device tree. When the operating system boots, no messages are
displayed, so the user generally has no idea what's wrong.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current code would print RAM size information like this:
DRAM: DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Turn a number of printf()s into debug() to get rid of the redundant
"DDR: " string like this:
DRAM: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
At some point we broke the detection of e500v1 class cores. Fix that
and simply the code to just utilize PVR_VER() to have a single case
statement.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix up the device tree property associated with the Flexcan clock
frequency. This property is used to calculate the bit timing parameters
for Flexcan.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This provides a function that will override the weak function
flush_icache to let 85xx boards to flush the icache
cc: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
The P2040/P2040E have no L2 cache. So we utilize the SVR to determine
if we are one of these devices and skip the L2 init code in cpu_init.c
and release. For the device tree we skip the updating of the L2 cache
properties but we still update the chain of caches so the CPC/L3 node
can be properly updated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We add XAUI_FM1 into the SERDES tables for P2041[e] devices. However
for the P2040[e] devices that dont support XAUI we handle this at
runtime via SVR checks. If we are on a P2040[e] device the SERDES
functions will behave as follows:
is_serdes_prtcl_valid() will always report invalid if prtcl passed in is
XAUI_FM1.
serdes_get_prtcl() will report NONE if the prtcl in the table is set to
XAUI_FM1.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2041 is the superset part that covers both P2040 & P2041. The only
difference between the two devices is that P2041 supports 10g/XAUI and
has an L2 cache.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Configuring DCSRCR to define the DCSR space to be 1G instead
of the default 4M. DCSRCR only allows selection of either 4M
or 1G.
Most DCSR registers are within 4M but the Nexus trace buffer
is located at offset 16M within the DCSR.
Configuring the LAW to be 32M to allow access to the Nexus
trace buffer. No TLB modification is required since accessing
the Nexus trace buffer from within u-boot is not required.
Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Had a typo in the ifdef for 85xx, should be CONFIG_MPC85xx for it to get
triggered. Was pull in the non-BookE magic number.
Reported-by: John Cortell
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
This patch removes the architecture specific implementation of
version_string where possible. Some architectures use a special place
and therefore we provide U_BOOT_VERSION_STRING definition and a common
weak symbol version_string.
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Peter Pan <pppeterpppan@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The multi serial support has a "ctlr" field which almost no one uses,
but everyone is forced to set to useless strings. So punt it.
Funny enough, the only code that actually reads this field (the mpc8xx
driver) has a typo where it meant to look for the SCC driver. Fix it
while converting the check to use the name field.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Rather than sticking arch/board/driver specific logic in the common
serial code, push it all out to the respective drivers. The serial
drivers declare these funcs weak so that boards can still override
things with their own definition.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Tested-by: Minkyu Kang <mk7.kang@samsung.com>
When booting with a ramdisk we bump the amount of memory reserved for
the device tree by FDT_RAMDISK_OVERHEAD. However we did not increase
the actual size in the device tree blob to match.
Its possible on boundary cases that we dont have enough memory according
to the device tree blob and get errors like:
WARNING: could not set linux,initrd-end FDT_ERR_NOSPACE
We can easily fix this by setting the device tree size at the same time
we bump the amount of memory reserved for the device tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
This is useful when we just want to wipe out the TLBs. There's currently
a function that resets the ddr tlbs to a different value; it is changed to
utilize this function. The new function can be used in conjunction with
setup_ddr_tlbs() for a board to temporarily map/unmap the DDR address
range as needed.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Fman device tree node binding allows for the entire Fman firmware binary
data to be embedded in the device tree. This eliminates the need to have
NOR flash mapped to Linux just so that the Fman driver can see the firmware.
The location of the Fman firmware is taken from the 'fman_ucode' environment
variable.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ePAPR specification says that phandle properties should be called
"phandle", and not "linux,phandle". To facilitate the migration from
"linux,phandle" to "phandle", we update fdt_qportal() to use the new
function, fdt_create_phandle(). This function abstracts the creation of
phandle properties.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some P4080 rev1 errata work-arounds, notably erratum SERDES4, required a
bank soft-reset after the bank was configured and enabled, even though
enabling a bank causes it to reset. Because the reset was required for
multiple errata, it was not properly enclosed in an #ifdef, and so was
not removed with all the other rev1 errata work-arounds.
Erratum SERDES-8 says that the clocks for bank 3 needs to be enabled if
bank 2 is enabled, but this was not being done for SERDES protocols 0xF
and 0x10. The bank reset also happened to enable bank 3 (apparently an
undocumented feature). Simply removing the reset breaks these two
protocols.
It turns out that every time we call enable_bank(), we do want at least
one lane of the bank enabled, either because the bank is supposed to be
enabled, or because we need the clock from that bank enabled.
For erratum SERDES-A001, we don't want to modify srds_lpd_b[] when we
call enable_bank(), because that array is used elsewhere to determine if
the bank is available.
Note that the side effect of these changes is that the work-arounds for
these two errata are now linked. Specifically, if SERDES-A001 is
enabled, then we need SERDES-8 enabled as well.
Because this was the only SERDES bank soft-reset, there is no need to
implement a work-around for erratum SERDES-A003.
Also fix an off-by-one error in a printf().
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ed Swarthout <swarthou@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add this option to allow boards to override the default read-to-write
turnaround time for better performance.
Signed-off-by: York Sun <yorksun@freescale.com>
Modify support for USB mode fixup:
- Add common support for USB mode and phy type
device tree fix-up for all USB controllers
mentioned in hwconfig string
- Fetch USB mode and phy type via hwconfig; if not
defined in hwconfig, then fetch them from env
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Checking width before setting DDR controller. SPD for DDR1 and DDR2 has
data width and primary sdram width. The latter one has different meaning
for DDR3.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In case of empty SPD or checksum error, fallback to raw timing on
supported boards.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We used to have fixed parameters for soldered DDR chips. This patch
introduces CONFIG_SYS_DDR_RAW_TIMING to enable calculation based on timing
data from DDR chip datasheet, implemneted in board-specific files or header
files.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On P1022/P1013 second USB controller is muxed with second
Ethernet controller. The current code to enable second USB
fails to properly clear pinmux bits used by ethernet. As a
result, Linux freezes when this controller is used. This
patch fixes the problem.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for 16-bit DDR bus. Also deal with system using 64- and 32-bit
DDR devices.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Only use DDR DIMM part number if SPD has valid length, to prevent from
display garbage in case SPD doesn't cover these fields.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If the bus width is 32-bit, burst chop should be disabled and burst length
should be 8. Read from SPD or other source to determine the width.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection for qp_info and liodn associated with Q/BMan. Also
rearrange setting of _tbl_sz variables to utilize existing ifdef
protection for things like FMAN.
Also add protection around setup_portals() call in corenet_ds board
code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection in LBC code to handle the case in which
CONFIG_SYS_BR0_PRELIM and CONFIG_SYS_OR0_PRELIM arent defined for a
build.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On a 8308 based board it was found that the PEX_GLK_RATIO register
(programmed in arch/powerpc/cpu/mpc83xx/pcie.c) was getting set to 0, This
was tracked to the fact that the pci express clock frequency was not being
assigned to the pciexp1_clk entry in the global data structure in file
arch/powerpc/cpu/mpc83xx/speed.c. Fix this and a similiar issue in
'do_clocks' command.
Signed-off-by: Bill Cook <cook@isgchips.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
CPO value and driver strength settings are board specifc.
Also allow SPD data fetch from any accessible I2C EEPROM.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Running on mpc837x without CONFIG_FSL_ESDHC leads to
i2c1_clk not being set at all. It is bound to clock
of encryption module. fix this.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We assumed that only a small set of compatiable strings would be needed
to find the PCIe device tree nodes to be fixed up. However on newer
platforms the simple rules no longer work. We need to allow specifying
the PCIe compatiable string for each individual SoC.
We introduce CONFIG_SYS_FSL_PCIE_COMPAT for this purpose and set it if
the default isn't sufficient.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reword "The DIMM max tCKmin is ..." to "The DDR clock is faster than the slowest
DIMM(s) can support". Fixed interger type in printf as well.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The compatible property for the L2 cache node (on 85xx systems that don't
have a CPC) was using a value for the property length that did not match
the actual length of the property.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
APM errata CHIP_21 for the 405EX/EXr (from the rev 1.09 document dated
4/27/11) states that rev D processors may wake up with the wrong feature
set. This patch implements the APM-proposed workaround.
To enable this patch for your board, add the appropriate define for your
CPU to your board header file. See kilauea.h for more information. The
following variants are supported:
#define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY
Please note that if you select the wrong define, your board will not
boot, and JTAG will be required to recover.
Tested on custom boards using:
CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY <sfalco@harris.com>
CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY <eibach@gdsys.de>
Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently, some linker scripts are found by common code in config.mk.
Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is
sometimes in arch config.mk and sometimes in board config.mk. Some
are found using an arch-specific rule for looking in CPUDIR, etc.
Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL
when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact
that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds.
Replace all of this -- except for a handful of boards that are actually
selecting a linker script in a unique way -- with centralized ldscript
finding.
If board code specifies LDSCRIPT, that will be used.
Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used.
If neither of these are specified, then the central config.mk will
check for the existence of the following, in order:
$(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
$(TOPDIR)/$(CPUDIR)/u-boot.lds
Some boards (sc3, cm5200, munices) provided their own u-boot.lds that
were dead code, because they were overridden by a CPUDIR u-boot.lds under
the old powerpc rules. These boards' own u-boot.lds have bitrotted and
no longer work -- these lds files have been removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount
This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Singed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce new CONFIG_SYS_FSL_TBCLK_DIV on 85xx platforms because
different SoCs have different divisor amounts. All the PQ3 parts are
/8, the P4080/P4080 is /16, and P2040/P3041/P5020 are /32.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Bank powerdown through RCW[SRDS_LPD_Bn] for XAUI on FM2 and SGMII on FM1
are swapped.
Erratum SERDES-A001 says that if bank two is kept disabled and after bank
three is enabled, then the PLL for bank three won't lock properly. The
work-around is to enable and then disable bank two after bank three is
enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Part of the SERDES9 erratum work-around is to set some bits in the SerDes
TTLCR0 register for lanes configured as XAUI, SGMII, SRIO, or AURORA. The
current code does this only for XAUI, so extend it to the other protocols.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The work-around for P4080 erratum SERDES-8 requires all lanes of banks two
and three to be disabled (powered down) in the RCW. Display a warning
message if this is not the case.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SerDes PLL bandwidth default setting is incorrect when no lanes are
configured as PCI Express.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration. Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.
The old definition of the "monitor" environment variable only determines
which video port to use for output. This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The
resolution was hard-coded into board-specific code. The Linux command-line
arguments needed to be hard-coded to the proper video definition string.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
A lot of boards set FT_FSL_PCI_SETUP directly in their board code
and don't check to see if CONFIG_PCI is actually defined. This
will cause the board compilation to fail if CONFIG_PCI is not
defined. The p1022ds board is one such example.
Instead of fixing every board this patch wraps FT_FSL_PCI_SETUP
around CONFIG_PCI so we can remove CONFIG_PCI and boards will
still build properly.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
versioned SEC properties changed names during development, so
for now search and update LIODNs for both "secX.Y" and
"sec-vX.Y" based properties.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The workaround for ESDHC111 should also be applied on
P2040/P3041/P5010/P5020 SoCs.
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we
need to enable for them to function.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P3041DS & P5020DS boards are almost identical (except for the
processor in them). Additionally they are based on the P4080DS board
design so we use the some board code for all 3 boards.
Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have
meaning on P3041DS/P5020DS. We utilize some of these for SERDES clock
configuration.
Additionally, the P3041DS/P5020DS support NAND.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rework and add some new APIs to the fsl_corenet_serdes code for use by
erratum and drivers.
* Rename serdes_get_bank() to serdes_get_bank_by_lane()
* Add serdes_get_first_lane returns which SERDES lane is used by device
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix fdt bportal to pass the bman revision number to kernel via device tree.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To make sure that machine change operation work successfully, change
timing parameters first before changing machine for chip select on IFC.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If FB address is defined specific address then don't grab memory for LCD
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
If a regions is reserved in the fdt, then it should not be used. Add
the memreserve regions to the lmb so that u-boot doesn't use them to
store the initrd.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The previous patch makes u-boot use the full accessible size of ram as
the default boot mapped size if CONFIG_SYS_BOOTMAPSZ is not defined,
which means boot_relocate_fdt() can be changed to depend solely on
CONFIG_OF_LIBFDT.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch adds a function getenv_bootm_mapsize() for obtaining the
size of the early mapped region accessible by the kernel during early
boot. It defaults to CONFIG_SYS_BOOTMAPSZ, or if not defined,
defaults to getenv_bootm_size(), which in turn defaults to the size of
RAM.
getenv_bootm_mapsize() can also be overridden with a "bootm_mapsize"
environmental variable.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
For the calls to boot_relocate_fdt(), boot_get_cmdline(), and
boot_get_kbd(), the value of bootmem_base is always obtained by
calling getenv_bootm_low(). Since the value always comes from the
same source, the calling signature for those functions can be
simplified by making them call getenv_bootm_low() directly.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
This converts tsec to use the new PHY Lib. All of the old PHY support
is ripped out. The old MDIO driver is split off, and placed in
fsl_mdio.c. The initialization is modified to initialize the MDIO
driver as well. The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Rename STANDALONE_LOAD_ADDR into CONFIG_STANDALONE_LOAD_ADDR
and allow that the architecture-specific default value gets
overwritten by defining the value in the board header file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Tsi Chung Liew <tsi-chung.liew@freescale.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-msingle-pic-base is a new gcc option for ppc and
it reduces the size of my u-boot with 6-8 KB.
While at it, add -fno-jump-tables too to save a
few more bytes.
-msingle-pic-base will be in gcc 4.6, however
backported patches are available at
http://bugs.gentoo.org/show_bug.cgi?id=347281
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
The -fPIC flag belongs with -mrelocatable, move it there.
Also change -fPIC to -fpic as this produces smaller
binaries.
However, currently -mrelocatable promotes -fpic to -fPIC, a
fix for this is in upcoming gcc 4.6 or you can apply this small
patch to gcc:
diff --git a/gcc/config/rs6000/sysv4.h b/gcc/config/rs6000/sysv4.h
index 8da8410..e4b8280 100644
--- a/gcc/config/rs6000/sysv4.h
+++ b/gcc/config/rs6000/sysv4.h
@@ -227,7 +227,8 @@ do { \
} \
\
else if (TARGET_RELOCATABLE) \
- flag_pic = 2; \
+ if (!flag_pic) \
+ flag_pic = 2; \
} while (0)
#ifndef RS6000_BI_ARCH
--
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Removed clearing of L2 cache as SRAM as it is not necessary without ECC.
This also speeds up the booting process.
Signed-off-by: Fabian Cenedese <cenedese@indel.ch>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark
level register description has been changed:
9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00
25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.
Signed-off-by: Chunhe Lan <b25806@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For soc which have pin multiplex relation, some of them can't enable
simultaneously. This patch add environment var 'hwconfig' content
defination for them. you can enable some one function by setting
environment var 'hwconfig' content and reset board. Detail setting
please refer doc/README.p1022ds
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the SERDES8 erratum work-around code that only applied to P4080
rev1, which is not supported by this version of U-Boot.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
renaming 85xx define CONFIG_NAND_OR_PRELIM to CONFIG_SYS_NAND_OR_PRELIM
and CONFIG_NAND_BR_PRELIM to CONFIG_SYS_NAND_BR_PRELIM to use the more
appropriate CONFIG_SYS prefix as well as be consistent with 83xx.
Signed-off-by: Matthew McClintock <msm@freescale.com>
cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Added SDHCDCR register to GUR struct
* Added SDHCDCR_CD_INV define related to SDHCDCR
* Added Pin Muxing define related to TDM on P102x
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1021 has some QE pins which need to be set in pmuxcr register before
using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and
UCC5 in Eth mode. QE9 and QE12 are set for MII management. QE12 needs to
be released after MII access because QE12 pin is muxed with LBCTL signal.
Also added relevant QE support defines unique to P1021.
The P1021 QE is shared on P1012, P1016, and P1025.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
i.e, to those parts that have PHY_CLK_VALID bits in their USB
CONTROL registers:
mpc8308 WU_INT, PHY_CLK_SEL, USB_EN, WU_INT_EN, ULPI_INT_EN
mpc831x PHY_CLK_VALID, WU_INT, CLKIN_SEL, PHY_CLK_SEL, UTMI_PHY_EN,
PLL_RESET, REFSEL, OTG_PORT, KEEP_OTG_ON, LSF_EN, USB_EN,
ULPI_INT_EN
mpc834x USB_EN, ULPI_INT1_EN (MPH only), ULPI_INT0_EN
mpc837x USB_EN, ULPI_INT_EN
(mpc832x, mpc8360 don't have a USB_EHCI_FSL compatible controller)
this prevents non-831x parts from never completing cpu_init_f(),
because the (non-existent) PHY_CLK_VALID bit never gets set.
Reported-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
The numeric constants in the switch statements are replaced by #defines
added to the common ddr_spd.h header. This dramatically improves the
readability of the switch statments.
In addition, a few of the longer lines were cleaned up, and the DDR2
type for an SO-RDIMM module was added to the DDR2 switch statement.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current FreeScale MPC-8xxx DDR SPD interpreter is using full 64-bit
integer divide operations to convert between nanoseconds and DDR clock
cycles given arbitrary DDR clock frequencies.
Since all of the inputs to this are 32-bit (nanoseconds, clock cycles,
and DDR frequencies), we can easily restructure the computation to use
the "do_div()" function to perform 64-bit/32-bit divide operations.
On 64-bit this change is basically a no-op, because do_div is
implemented as a literal 64-bit divide operation and the instruction
scheduling works out almost the same.
On 32-bit PowerPC a fully accurate 64/64 divide (__udivdi3 in libgcc) is
over 1.1kB of code and thousands of heavily dependent cycles to compute,
all of which is linked from libgcc. Another 1.2kB of code comes in for
the function __umoddi3.
It should be noted that nothing else in U-Boot or the Linux kernel seems
to require a full 64-bit divide on my 32-bit PowerPC.
Build-and-boot-tested on the HWW-1U-1A board using DDR2 SPD detection.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Acked-by: York Sun <yorksun@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We utilize the compatible string to find the node to add fsl,liodn
property to. However P3041 & P5020 don't have "fsl,p4080-pcie"
compatible for their PCIe controllers as they aren't backwards compatible.
Allow the macro's to specify the PCIe compatible to use to allow SoC
uniqueness. On P3041 & P5020 we utilize "fsl,qoriq-pcie-v2.2" for the
PCIe controllers.
Signed-off-by: Laurentiu TUDOR <Laurentiu.Tudor@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix up the device tree property associated with the IEEE 1588 timer
source frequency. Currently we only support the IEEE 1588 timer source
being the internal eTSEC system clock (for those SoCs with IEEE 1588
support). The eTSEC clock is ccb_clk/2.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the P1023 the Fman freq is equivalent to the system bus freq, not 1/2
of it. Also we only have one Fman so no need for the code to deal with
a second.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On CoreNet based SoCs (P2040, P3041, P4080, P5020) we have some
additional rules to determining the various frequencies that PME & FMan
IP blocks run at.
We need to take into account:
* Reduced number of Core Complex PLL clusters
* HWA_ASYNC_DIV (allows for /2 or /4 options)
On P2040/P3041/P5020 we only have 2 Core Complex PLLs and in such SoCs
the PME & FMan blocks utilize the second Core Complex PLL. On SoCs
like p4080 with 4 Core Complex PLLs we utilize the third Core Complex
PLL for PME & FMan blocks.
On P2040/P3041/P5020 we have the added feature that we can divide the
PLL down further by either /2 or /4 based on HWA_ASYNC_DIV. On P4080
this options doesn't exist, however HWA_ASYNC_DIV field in RCW should be
set to 0 and this gets a backward compatiable /2 behavior.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_FM_MURAM_SIZE varies from SoC to SoC to specify it in
config_mpc85xx.h for those parts with a Frame Manager.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SDHC clock is equal to CCB on P1010 and P1014 not CCB/2.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add defines for FSL_SATA_V2, # of DDR controllers, reset value of CCSRBAR
and SDHC erratum.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add Support for Freescale P1024/P1025 (dual core) and
P1015/P1016 (single core) processors.
P1024 is a variant of P1020 processor with a core frequency from
400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA
P1025 is a variant of P1021 processor with a core frequency from
400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA
P1015 is a variant of P1024 processor with single core and P1016 is a
variant of P1025 processor with single core.
Added comments in config_mpc85xx.h to denote single core versions of
processors.
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the case the QE's microcode is stored in nand flash, we need to load it from
NAND flash to ddr first then the qe_init can get the ucode correctly.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Beside displaying RDIMM or UDIMM, this patch adds display of the model numbers
embedded in SPD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL PCIe controller v2.1:
- New MSI inbound window
- Same Inbound windows address as PCIe controller v1.x
Added new pit_t member(pmit) to struct ccsr_pci for MSI inbound window
FSL PCIe controller v2.2 and v2.3:
- Different addresses for PCIe inbound window 3,2,1
- Exposed PCIe inbound window 0
- New PCIe interrupt status register
Added new Interrupt Status register to struct ccsr_pci & updated pit_t array
size to reflect the 4 inbound windows.
To maintain backward compatiblilty, on V2.2 or greater controllers we
start with inbound window 1 and leave inbound 0 with its default value
(which maps to CCSRBAR).
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are some differences between CoreNet (P2040, P3041, P5020, P4080)
and and non-CoreNet (P1017, P1023) based SoCs in what features exist and
the memory maps.
* Rename various immap defines to remove _CORENET_ if they are shared
* Added P1023/P1017 specific memory offsets
* Only setup LIODNs or LIODN related code on CORENET based SoCs
(features doesn't exist on P1023/P1017)
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add P1023 (dual core) & P1017 (single core) specific information:
* SERDES Table
* Added P1023/P1017 to cpu_type_list and SVR list
(fixed issue with P1013 not being sorted correctly).
* Added P1023/P1027 to config_mpc85xx.h
* Added new LAW type introduced on P1023/P1017
* Updated a few immap register/defines unique to P1023/P1017
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can simplify some cpu/SoC level initialization by moving it to be
after the environment and non-volatile storage is setup as there might
be dependancies on such things in various boot configurations.
For example for FSL SoC's with QE if we boot from NAND we need it setup
to extra the ucode image to initialize the QE. If we always do this
after environment & non-volatile storage is working we can have the code
be the same regardless of NOR, NAND, SPI, MMC boot.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move some processor specific QE defines into config_mpc85xx.h and use
QE_MURAM_SIZE to cleanup some ifdef mess in the QE immap struct.
Also fixed up some comment style issues in immap_qe.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards
pretty much do the same thing. The only variations are in how many
controllers or DIMMs per controller exist. To make this work we
standardize on the names of the SPD_EEPROM_ADDRESS defines based on the
use case of the board.
We allow boards to override get_spd to either do board specific fixups
to the SPD data or deal with any unique behavior of how the SPD eeproms
are wired up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Every 85xx board implements fsl_ddr_get_mem_data_rate via get_ddr_freq()
and every 86xx board uses get_bus_freq(). If implement get_ddr_freq()
as a static inline to call get_bus_freq() we can remove
fsl_ddr_get_mem_data_rate altogether and just call get_ddr_freq()
directly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We've been utilizing board_lmb_reserve to reserve the boot page for MP
systems. We can just move this into arch_lmb_reserve for 85xx & 86xx
systems rather than duplicating in each board port.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In a manner similar to passing ethernet stashing parameters into device
tree for "gianfar", extend the support to the "fsl,etsec2" as well.
Signed-off-by: Pankaj Chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove declerations of fsl_ddr_set_memctl_regs in board files with and
place it into a common header.
Based on patch from Poonam Aggrwal.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Integrated Flash Controller (IFC) is used to access the external
NAND Flash, NOR Flash, EPROM, SRAM and Generic ASIC memories.Four chip
selects are provided in IFC so that maximum of four Flash devices can be
hooked, but only one can be accessed at a given time.
Features supported by IFC are,
- Functional muxing of pins between NAND, NOR and GPCM
- Support memory banks of size 64KByte to 4 GBytes
- Write protection capability (only for NAND and NOR)
- Provision of Software Reset
- Flexible Timing programmability for every chip select
- NAND Machine
- x8/ x16 NAND Flash Interface
- SLC and MLC NAND Flash devices support with
configurable
page sizes of upto 4KB
- Internal SRAM of 9KB which is directly mapped and
availble at
boot time for NAND Boot
- Configurable block size
- Boot chip select (CS0) available at system reset
- NOR Machine
- Data bus width of 8/16/32
- Compatible with asynchronous NOR Flash
- Directly memory mapped
- Supports address data multiplexed (ADM) NOR device
- Boot chip select (CS0) available at system reset
- GPCM Machine (NORMAL GPCM Mode)
- Support for x8/16/32 bit device
- Compatible with general purpose addressable device
e.g. SRAM, ROM
- External clock is supported with programmable division
ratio
- GPCM Machine (Generic ASIC Mode)
- Support for x8/16/32 bit device
- Address and Data are shared on I/O bus
- Following Address and Data sequences can be supported
on I/O bus
- 32 bit I/O: AD
- 16 bit I/O: AADD
- 8 bit I/O : AAAADDDD
- Configurable Even/Odd Parity on Address/Data bus
supported
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are only
ever connected on SERDES.
Updated MPC85xx_PORDEVSR_IO_SEL & MPC85xx_PORDEVSR_IO_SEL_SHIFT
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1011, P1012, P1015, P1016, P1020, P1021, P1024, & P1025 SoCs require
that we initialize the SERDES registers if the lanes are configured for
PCIe. Additionally these devices PCIe controller do not support ASPM
and we have to explicitly disable it.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable workaround for errata ELBC A001, ESDHC 111 & SATA A001 on
P1022/P1013 SoCs.
Also updated P1022DS config to properly enable CONFIG_FSL_SATA_V2.
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, _end is used for end of BSS section. We want _end to mean
end of u-boot image, so we rename _end to __bss_end__ first.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
The fix for errata workaround is to avoid covering physical address
0xff000000 to 0xffffffff during the implementation.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
rcw_en bit is only available for DDR3 controllers. It is a reserved bit on
DDR1 and DDR2 controllers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To recognize DIMMs with ECC capability by testing ECC bit only. Not to be
confused by Address Parity bit.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit 8aba9dceeb
Divides variable of linker flags to LDFLAGS-u-boot and LDFLAGS
breaks the usage of --gc-section to build nand_spl. We still need linker option
--gc-section for every uboot image, not only the main one. LDFLAGS_FINAL passes
the --gc-sections to each uboot image.
To get the proper linker flags, we use LDFLAGS and LDFLAGS_FINAL to replace
PLATFORM_LDFLAGS in the Makefile of each nand_spl board.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
There is a small ordering issue in the master core in that we need to
make sure the disabling of the timebase in the SoC is visible before we
set the value to 0. We can simply just read back the value to
synchronizatize the write, before we set TB to 0.
Reported-by: Dan Hettena
Tested-by: Dan Hettena
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The POST word is stored in a spare register in the PIC on MPC8[5/6]xx
processors. When interrupt_init() is called, this register gets reset
which resulted in all POST_RAM POSTs not being ran due to the corrupted
POST word. To resolve this, store off POST word before the PIC is
reset, and restore it after the PIC has been initialized.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Copying directly from ECM/PQ3 is not correct for how CoreNet based
platforms handle boot page translation.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The write recovery time of both registers should match. Since mode register
doesn't support cycles of 9,11,13,15, we should use next higher number for
both registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When DDR data rate is higher than 1200MT/s or controller interleaving is
enabled, additional cycle for write-to-read turnaround is needed to satisfy
dynamic ODT timing.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Use SPMR instead of HRCWL when calculating clocks as HCRWL
may be changed and the CPU will not pick up all changes
until there is a POR. u-boot will think SPMF has changed and get
the clocks wrong.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fix a problem for the pcie enumeration when the mpc83xx
pcie controller is connected with switch or we use both of the two
pcie controller.
Signed-off-by: Leo Liu <liucai.lfn@gmail.com>
fix codingstyle and compiler warning: 'pcie_priv' defined but not used
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The P1013 is a single core version of P1022 and thus should use the
p1022_serdes.c code. It was acciently pointing to p1013_serdes.c which
doesn't exist.
Reported-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Workaround for the following errata:
DDR111 - MCKE signal may not function correctly at assertion of HRESET
DDR134 - The automatic CAS-to-Preamble feature of the DDR controller can
calibrate to incorrect values
These two workarounds must be implemented together because they touch
common registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use unique erratum number instead of platform number.
Enable command that reports errata on MPC8572DS.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This polling loop is not required normally, unless specifically stated in
workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linker needs to use the proper endian/bfd flags even when doing partial linking.
LDFLAGS_u-boot sets linker option which is called it when U-boot is built
(u-boot final).
LDFLAGS sets necessary option by partial linking (use in cmd_link_o_target).
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
ctrl_regs.c: In function 'set_ddr_sdram_mode_2':
ctrl_regs.c:690:6: warning: unused variable 'i'
'i' is only used by DDR3 code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Future SoC (like the P1010) replace the LBC controller with the new IFC
(Integrated Flash Controller) so ensure we properly protect code that is
related to the LBC.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Hwconfig is called before relocating. Use the new hwconfig APIs.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Extend board specific parameters to include cpo, write leveling override
Extend write leveling sample to 0xf
Adding rcw overrid for quad-rank RDIMMs
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum DDR-A003 requires workaround to correctly set RCW10 for registered DIMM.
Also adding polling after enabling DDR controller to ensure completion.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added fsl_ddr_get_version() function to for DDR3 to poll DDRC IP version
(major, minor, errata) to determine if unique mode registers are available.
If true, always use unique mode registers. Dynamic ODT is enabled if needed.
The table is documented in doc/README.fsl-ddr. This function may also need
to be extend for future other platforms if such a feature exists.
Enable address parity and RCW by default for RDIMMs.
Change default output driver impedance from 34 ohm to 40ohm. Make it 34ohm for
quad-rank RDIMMs.
Use a formula to calculate rodt_on for timing_cfg_5.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch exposes more registers which can be used by the DDR drivers or
interactive debugging. U-boot doesn't use all the registers in DDRC.
When advanced tuning is required, writing to those registers is needed.
Add writing to cdr1, cdr2, err_disable, err_int_en and debug registers
Add options to override rcw, address parity to RDIMMs.
Use array for debug registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add fsl_ddr:ecc=on in hwconfig. If ECC is enabled in board configuration file,
ECC can be turned on/off by this switch. If this switch is omitted, it is ON by
default.
Updated hwconfig calls to use local buffer.
Syntax is
hwconfig=fsl_ddr:ecc=on
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.
Eventually this should be handled by Kconfig & defconfigs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
There are several users of the hwconfig APIs (8xxx DDR) before we have
the environment properly setup. This causes issues because of the
numerous ways the environment might be accessed because of the
non-volatile memory it might be stored in. Additionally the access
might be so early that memory isn't even properly setup for us.
Towards resolving these issues we provide versions of all the hwconfig
APIs that can be passed in a buffer to parse and leave it to the caller
to determine how to allocate and populate the buffer.
We use the _f naming convention for these new APIs even though they are
perfectly useable after relocation and the environment being ready.
We also now warn if the non-f APIs are called before the environment is
ready to allow users to address the issues.
Finally, we convert the 8xxx DDR code to utilize the new APIs to
hopefully address the issue once and for all. We have the 8xxx DDR code
create a buffer on the stack and populate it via getenv_f().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Add P2040 SoC specific information:
* SERDES Table
* Added p2040 to cpu_type_list and SVR list
* Added number of LAWs for p2040
* Set CONFIG_MAX_CPUS to 4 for p2040
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1014 is similar to the P1010 processor with the following differences:
- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
* TCP/IP acceleration and classification capabilities
* IEEE 1588 support
* Lossless flow control
* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
software watchdog timer, and four general-purpose timers
* Dual DUARTs
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_MPC85xx_SERDES1_ADDR was defined wrong as
CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_SERDES2_OFFSET.
It should be as
CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_SERDES1_OFFSET.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Rather than defining it config.mk we can set it in config.h and remove
config.mk from several boards that don't need it.
We mimic what 4xx does and introduce CONFIG_RESET_VECTOR_ADDRESS for
config.h to set.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
This patch adds fsl_ddr_sdram_size to only calculate the ddr sdram size, in
case that the DDR SDRAM is initialized in the 2nd stage uboot and should not
be intialized again in the final stage uboot.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There's no compelling reason to have the output on bootup or the
"flinfo" command print "flash" in uppercase, so use the proper case
where appropriate.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Simultaneous FCM and GPCM or UPM operation may erroneously trigger bus
monitor timeout. Set timeout to maximum to avoid.
Based on a patch from Lan Chunhe <b25806@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CoreNet Platform Cache single-bit data error scrubbing will cause data
corruption. Disable the feature to workaround the issue.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CoreNet Platform Cache single-bit tag error scrubbing will cause tag
corruption. Disable the feature to workaround the issue.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the parsing of hwconfig to determine if to use spd into common code
so we can share it across all boards instead of duplicating it
everywhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
False multi-bit ECC errors will be reported by the eSDHC buffer which
can trigger a reset request.
We disable all ECC error checking on SDHC.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The default value of the SRS, VS18 and VS30 and ADMAS fields in the host
controller capabilities register (HOSTCAPBLT) are incorrect. The default
of these bits should be zero instead of one.
Clear these bits out when we read HOSTCAPBLT.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Do not issue a manual asynchronous CMD12. Instead, use a (software)
synchronous CMD12 or AUTOCMD12 to abort data transfer.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the needed defines and code to utilize the common 8xxx srio init
code to setup LAWs and modify device tree if we have SRIO enabled on a
board.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Moved the SRIO init out of corenet_ds and into common code for
8xxx/QorIQ processors that have SRIO. We mimic what we do with PCIe
controllers for SRIO.
We utilize the fact that SRIO is over serdes to determine if its
configured or not and thus can setup the LAWs needed for it dynamically.
We additionally update the device tree (to remove the SRIO nodes) if the
board doesn't have SRIO enabled.
Introduced the following standard defines for board config.h:
CONFIG_SYS_SRIO - Chip has SRIO or not
CONFIG_SRIO1 - Board has SRIO 1 port available
CONFIG_SRIO2 - Board has SRIO 2 port available
(where 'n' is the port #)
CONFIG_SYS_SRIOn_MEM_VIRT - virtual address in u-boot
CONFIG_SYS_SRIOn_MEM_PHYS - physical address (for law setup)
CONFIG_SYS_SRIOn_MEM_SIZE - size of window (for law setup)
[ These mimic what we have for PCI and PCIe controllers ]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
This change does the following:
- Adds printing of negotiated link width. This information can be
useful when debugging PCIe issues.
- Makes it optional for boards to implement board_serdes_name().
Previously boards that did not implement it would print unsightly
output such as "PCIE1: Connected to <NULL>..."
- Rewords the PCIe boot output to reduce line length and to make it
clear that the "base address XYZ" value refers to the base address of
the internal processor PCIe registers and not a standard PCI BAR
value.
- Changes "PCIE" output to the standard "PCIe"
Before change:
PCIE1: connected to <NULL> as Root Complex (base addr ef008000)
01:00.0 - 10b5:8518 - Bridge device
02:01.0 - 10b5:8518 - Bridge device
02:02.0 - 10b5:8518 - Bridge device
02:03.0 - 10b5:8518 - Bridge device
PCIE1: Bus 00 - 05
PCIE2: connected to <NULL> as Endpoint (base addr ef009000)
PCIE2: Bus 06 - 06
After change:
PCIe1: Root Complex of PEX8518 Switch, x4, regs @ 0xef008000
01:00.0 - 10b5:8518 - Bridge device
02:01.0 - 10b5:8518 - Bridge device
02:02.0 - 10b5:8518 - Bridge device
02:03.0 - 10b5:8518 - Bridge device
PCIe1: Bus 00 - 05
PCIe2: Endpoint of VPX Fabric A, x2, regs @ 0xef009000
PCIe2: Bus 06 - 06
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since all the PCIe controllers are connected over SERDES on the SoCs we
can utilize is_serdes_configured() to determine if a controller is
enabled. After which we can setup the ATMUs and LAWs for the controller
in a common fashion and allow board code to specify what the controller
is connected to for reporting reasons.
We also provide a per controller (rather than all) for some systems that
may have special requirements.
Finally, we refactor the code used by the P1022DS to utilize the new
generic code.
Based on patch by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously we passed in a specifically named struct pci_controller to
determine if we had setup the particular PCI bus. Now we can search for
the struct so we dont have to depend on the name or the struct being
statically allocated.
Introduced new find_hose_by_cfg_addr() to get back a pci_controller struct
back by searching for it means we can do things like dynamically allocate
them or not have to expose the static structures to all users.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
We set the L1 dache register with a bogus register value. Need to be
using 'r3' instead of 'r0'.
Reported-by: John Traill <john.traill@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add spaces to cause the informational prints to line up with
the ones from init_func_ram() in board.c. Output now looks like
this:
....
DRAM: Detected 4096 MB of memory
This U-Boot only supports < 4G of DDR
You could rebuild it with CONFIG_PHYS_64BIT
DDR: 2 GiB (DDR2, 64-bit, CL=5, ECC off)
....
The prints from lbc_sdram_init() have also been modified to line
line up and changed to start with "LBC SDRAM" instead of the
confusing "SDRAM".
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This config option is for an erratum workaround; rename it to be more
clear. Also, drop it from config files don't need it and were
undefining it.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
sdram_init() is used to initialize sdram on the lbc. Rename it
accordingly.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correct initdram to use phys_size_t to represent the size of
dram; instead of changing this all over the place, and correcting
all the other random errors I've noticed, create a
common initdram that is used by all non-corenet 85xx parts. Most
of the initdram() functions were identical, with 2 common differences:
1) DDR tlbs for the fixed_sdram case were set up in initdram() on
some boards, and were part of the tlb_table on others. I have
changed them all over to the initdram() method - we shouldn't
be accessing dram before this point so they don't need to be
done sooner, and this seems cleaner.
2) Parts that require the DDR11 erratum workaround had different
implementations - I have adopted the version from the Freescale
errata document. It also looks like some of the versions were
buggy, and, depending on timing, could have resulted in the
DDR controller being disabled. This seems bad.
The xpedite boards had a common/fsl_8xxx_ddr.c; with this
change only the 517 board uses this so I have moved the ddr code
into that board's directory in xpedite517x.c
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some platforms might want to override the default wimge=0 for
DDR. Add CONFIG_SYS_PPC_DDR_WIMGE for those platforms to use.
This will initially only be used by TQM85xx, but could be
useful for other boards or testing going forward. Note that
the name of this define is not 85xx-specific. WIMGE is a
fairly universal concept, so any ppc platforms that require
different WIMGE settings for DDR can use the same #define.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we have serdes support for all 85xx/86xx/Pxxx chips we can
replace the is_fsl_pci_cfg() code with the is_serdes_configured().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES. This mimics the code we have in place
for the 85xx platforms.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Created a section in the Makefile for SoC specific SERDES code. Also
added P1013 SERDES (use P1022 SERDES code).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Patch 8ef583a0 [miiphy: convert to linux/mii.h] introduced a small
problem in the ppc4xx miiphy.c version. This patch fixes this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In some usages of inline assembly, hard-coded registers were
specified when a scratch register should have been used instead.
Signed-off-by: Timur Tabi <timur@freescale.com>
The following commit:
commit 882b7d726f
Author: Mike Frysinger <vapier@gentoo.org>
Date: Wed Oct 20 03:41:17 2010 -0400
do_reset: unify duplicate prototypes
missed the 74xx_7xx and mpc86xx arches and the ppmc7xx board do_reset()
functions which resulted in build errors such as:
cpu.c:128: error: conflicting types for 'do_reset'
include/command.h:102: error: previous declaration of 'do_reset' was here
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
By rearranging the linker script we get support for
relocation of -fpic for free.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Use common ppc4xx linker script for xilinx ppc440 and ppc405 related boards.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fix a problem for the pcie enumeration for mpc83xx cpus. Without
this we will not get correct value in hose->regions[...].
The pointer *reg in function mpc83xx_pcie_init_bus() shall not be changed.
Because we will use this pointer as a parameter to call function
mpc83xx_pcie_register_hose().
Signed-off-by: Baidu Boy <liucai.lfn@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This fixes the compiling error for the board which doesn't have NOR flash
(so CONFIG_FLASH_BASE is not defined)
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some systems need to relocate the env_addr pointer early because the
location it points to will get invalidated before env_relocate is
called. One example is on systems that might use a L2 or L3 cache
in SRAM mode and initialize that cache from SRAM mode back to being
a cache in cpu_init_r.
We set this on the 85xx boards that have support for NAND, SPI, or
SDHC/MMC boot support as they use a secondary cache in SRAM mode and
need the env_addr pointer relocated since we change from SRAM to normal
cache mode in cpu_init_r.
Also removed CONFIG_SYS_SPL as its not used anywhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After the removal of COLD/WARM start flags my mpc8321
board didn't boot anymore.
Trial and error suggests that map/remap_flash_by_xxx needs
to wait after updating LBLAWAR1 to make sure the the change has
reached the HW before continuing with the code that depends on it.
Final fix suggested by Scott Wood.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The duplication of the do_reset prototype has gotten out of hand,
and they're not all in sync. Unify them all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When the cache is enabled in SDRAM we need to flush not only the global
data area but also the bd_info struct in relocate_code. This patch now
flushed the complete dcache (all dcache lines) via flush_dcache() instead
of adding a flush_dcache_range() call for bd_info since this is faster.
Signed-off-by: Stefan Roese <sr@denx.de>
Use the return value of cmd_usage instead of ignoring this
and returning a 1.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Timur Tabi <timur@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
This commit adapts 4xx boards for partial linking with --gc-sections.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: David Updegraff <dave@cray.com>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Larry Johnson <lrj@acm.org>
Cc: Peter De Schrijver <p2@mind.be>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
Cc: Daniel Poirot <dan.poirot@windriver.com>
Acked-by: Stefan Roese <sr@denx.de>
The switch from archive libraries to partial linking has introduced a
number of problems, that are non-trivial to solve. For example, it is
no longer possible to include individual object files in the linker
script as we did before for example in the case of boards with
embedded environment to fill up the gap caused by the need to align
the environment on flash erase block boundaries.
The best (but unfortunately not easiest) approach to address this
problem is to enable -ffunction-sections (and -fdata-sections) so
we can again (and even in much finer granularity) place certain code
where we want it. When doing this step, it seems only consequent to
also add --gc-sections which has the added benefit of reducing the
memory footprint of the U-Boot image (both in flash and in RAM).
Unfortunately, this requires changes to a lot of linker scripts.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
As we try to get rid of board specific config.mk files we must
provide a way for board specific settings of the LDSCRIPT variable
(path to the linker script) where needed.
We now implement the following hierarchy:
- Highest priority has a "#define CONFIG_SYS_LDCONFIG" in the board
config file.
- If CONFIG_SYS_LDCONFIG is not set, and the system is booting from
NAND (CONFIG_NAND_SPL is set), then a board specific linker
script board/$(BOARDDIR)/u-boot-nand.lds gets used.
- If we are not booting from NAND, we test if a processor specific
linker script arch/powerpc/cpu/$(CPU)/u-boot.lds exists; if so we
use that.
- As default, arch/powerpc/config.mk gets used.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
So far, only the BAB7xx board would call the initialise_w83c553f()
function for the WINBOND 83C553 chip, even though some other boards
(HIDDEN_DRAGON, Sandpoint8240, Sandpoint8245) enabled it in their
board configuration. These boards were also missing other config
settings needed for that, which resulted in build errors like this:
drivers/pci/libpci.o:(.got2+0x84): undefined reference to `ide_bus_offset'
Switch arch/powerpc/lib/board.c to call initialise_w83c553f() not on a
per-board base, but when a WINBOND_83C553 in enabled in a
configuration (like BAB7xx), and disable it in the boards that had
this set so far.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Yusdi Santoso <yusdi_santoso@adaptec.com>
Cc: Jim Thompson <jim@musenki.com>
Acked-by: Stefan Roese <sr@denx.de>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
