Apply errata based on PL310 version instead of compile
time. Also set Prefetch offset to 15, since it improves
memcpy performance by 35%. Don't enable Incr double
Linefill enable since it adversely affects memcpy
performance by about 32MB/s and reads by 90MB/s. Tested
with 4K to 16MB sized src and dst aligned buffer.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
According to "Table 5-1. Boot Device Select" (page 335,
i.MX 6Dual/6Quad Applications Processor Reference Manual, Rev. 4, 09/2017)
the BOOT_CFG1[3] have following values (regarding EIM booting):
0 - NOR flash and 1 - ONENAND
This commit provides correct identification of the boot medium for IMX6Q
boards booting from NOR memory (MCCMON6 is one of them).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
We have converted mmc to driver model on Poplar. So let's clean up
board level mmc initialization code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add common reset driver for all Allwinner SoC's.
Since CLK and RESET share common DT compatible, it is CLK driver
job is to bind the reset driver. So add CLK bind call on respective
SoC driver by passing ccu map descriptor so-that reset deassert,
deassert operations held based on ccu reset table defined from
CLK driver.
Select DM_RESET via CLK_SUNXI, this make hidden section of RESET
since CLK and RESET share common DT compatible and code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A64.
Implement USB clock enable and disable functions for
OHCI, EHCI, OTG and USBPHY gate and clock registers
via ccu clk gate table.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE.
However even the controller is enabled, the mux for the pins
are not set.
This patch follows the existing mux method. Since the pads are
different, separate check is added for each i2c.
Tested with A64-SOM204 board.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The ICIDs for the qdma device are not configured through SCFG but
through some registers found in the actual device register block.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1043A/LS1023A 23x23 package silicon has different SVR:VAR_PER.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It enables DWC2 OTG gadget driver support for Poplar board. As
usb2_phy_init() is being always called from board_init(), we can save
the call from board_usb_init().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CR80 register has multiple interrupt bits, the code is supposed
to check bit 8 but instead uses a logical and. In most cases this
probably did not affect real operations since at that stage typically
none of the other bits are set.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
According to the data sheet bits 10-8 are PHYDRAM_CK_EN. Fix mask
to allow setting PHYDRAM_CK_EN correctly.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter
5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed
for correct operation of DDR. Assume the default DDR pin configuration
which seems to work well on a Colibri VF50.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
When running usb dwc3 gadget driver, we meet random USB enumeration failure in fastboot.
The root cause is a cache coherence issue. When it happens, the ctrl_req in
gadget driver is allocated at 0xfe932f40, and the usb_composite_dev (cdev)
is allocated at 0xfe932f60. So after we submit the setup request (cache flushed) to USB
controller, any accessing to usb_composite_dev variable will cause the cache line refill, then
when setup transfer is completed, reading the setup data in ctrl_req will gets old value from
cache not from memory.
The ctrl_req is allocated by API dma_alloc_coherent, but u-boot don't have cohernet memory.
so it still needs cache maintain operations before/after HW accessing. Since the cache flush or
invalidate bases on cache line, so when the allocated memory size is not cache line aligned,
potentially it may meet such issue.
This patch modifies the dma_alloc_coherent API to round the size to cache line aligned.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Refactor dram_pll_init to accept args to configure different pll freq.
Introduce dram_enable_bypass and dram_disable_bypass
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable DM for USB peripheral in the musb-new driver.
Also make sure that the driver can be used in the SPL.
This implies that:
* the driver must work with and without the OF_CONTROL option. That
in turn, implies that the platform data can be passed in a struct
ti_musb_platdata or be read from the dtb
* usb.o is linked in the SPL if host support is enabled
Another change is that the driver does not fail to bind (and stop the boot
process) if one of the child driver does not bind. Reporting the error is
enough. This kind of error would appear if the port is configured in the
DTS but the driver is not activated in the config.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for lx2160a SoC
-----BEGIN PGP SIGNATURE-----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=aT7d
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
This allows the driver to be used without OF_CONTROL.
AM335x support DM_SPL but does not use SPL_OF_CONTROL. Enabling DM_I2C in
SPL thus requires that the omap I2C can be passed platdata.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move away from SoC specific headers to handle different register layout.
Instead use driver data to get appropriate register layouts like in the
kernel. While at it, perform some mostly cosmetic alignment/cleanup in
the functions being updated.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
In some STM32 SoC packages, GPIO bank has not always 16 gpios.
Several cases can occur, gpio hole can be located at the beginning,
middle or end of the gpio bank or a combination of these 3
configurations.
For that, gpio bindings offer the gpio-ranges DT property which
described the gpio bank mapping.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
NXP layerscape architecture Chassis 3.2 builds upon chassis3
architecture with changes like DDR Memory map change,
removal of IFC and support of upto 8 I2C controller.
Patch add README.lsch3_2 and the above changes under
macro CONFIG_NXP_LSCH3_2.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some lsch3 based SoCs like lx2160a contains three
serdes modules.
Add support for third serdes protocol in lsch3
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Workaround of erratum A010539 clears the RCW source field in PORSR1
register, causing failure of detecting boot source using this method.
Use SMC call if U-Boot runs at EL2. If SMC is not implemented or
running at EL3, continue to read PORSR1 and presume QSPI as boot
source if erratum workaround A010539 is enabled and RCW source is
cleared.
Signed-off-by: York Sun <york.sun@nxp.com>
Adds SMC calls for getting DDR size and bank info for TFABOOT.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PORSR register holds the cfg_rcw_src field which can be used
to identify boot source.
Further, it can be used to select the environment location.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix multiple checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
Move static definitions to cpu.c file, as it doesn't allow
the cpu.h file to be included in multiple c files.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch sets the PLL of CPU cluster B (BPLL) to 600 MHz.
This decreases the boot time of Linux 4.19 by about 8%.
The 600 MHz are inspired by the 600 MHz used for LPLL initialization
(came in with commit 9f636a249c).
Tested on RK3399-Q7 on Haikou base board.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make adjustments to the rv1108 clock driver in order to align it
with the internal Rockchip version.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip socs can route the debug uart pins through the d+ and d- pins
of one specific usbphy per soc. Add a config option and implement the
setting on the rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed up to mark grf as maybe unused:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds pinctrl support for MT7629 SoC. The IO core found on
the SoC has the registers for pinctrl, pinconf and gpio mixed up in
the same register range. Hence the driver also implements the gpio
functionality through UCLASS_GPIO.
This also creates a common file as there might be other chips that use
the same binding and driver, then being a little more abstract could
help in the long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a general board file based on MT7629 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Amlogic Meson SoCs ROM supports a boot over USB with a custom protocol.
When no other boot medium are available (or by forcing the USB mode), the
ROM sets the primary USB port as device mode and waits for a Host to
enumerate.
When enumerated, a custom protocol described at [1] permits writing to
memory and execute some specific FIP init code to run the loaded
Arm Trusted Firmware BL2 and BL3 stages before running the BL33 stage.
In this mode, we can load different binaries that can be used by U-boot
like a script image file.
This adds support for a custom USB boot stage only available when the
boot mode is USB and the script file at a pre-defined address is valid.
This support was heavily copied from the Sunxi Allwinner FEL U-Boot support.
The tool pyamlboot described at [2], permits using this boot mode on boards
exposing the first USB port, either as OTG or Host port.
[1] https://github.com/superna9999/pyamlboot/blob/master/PROTOCOL.md
[2] https://github.com/superna9999/pyamlboot/blob/master/README.md
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds a minimal clock driver for the Amlogic AXG SoC to handle
the basic gates and PLLs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds support for the Amlogic AXG SoC, which is very close from
the Amlogic GXL SoCs with :
- Same 4xCortex-A53 CPUs but clocked at 1.2GHZ max
- DDR Interface limited to DDR4 16bit
- The whole physical register address space has been moved to 0xfxxxxxxx
- The pinctrl setup has changed
- The clock tree is different enough to use a different driver
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are different
in this SoC. Rework the meson arch directory to prepare for this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Drop the _AC and UL macros from common.h. Linux headers is the original
source of this macro, so keep its definition in the same header.
Update existing users of these macros to include const.h directly.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Rick Chen <rick@andestech.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Allow EL3 to handle all the External Abort and SError interrupt
exception occur in all exception levels.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Jagan Teki <jagan@openedev.com>
A64 and H6 support automatic delay calibration and Linux driver uses it
instead of hardcoded delays. Add support for it to u-boot driver.
Fixes eMMC instability on Pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update TI Keystone 2 driver to re-use common mdio lib.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Networking support for all TI K2 boards converted to use DM model and
CONFIG_DM_ETH enabled in all corresponding defconfig files, hence drop
unused non DM K2 networking code.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
At the moment we rely on the infamous get_ram_size() function to learn
the actual DRAM size in U-Boot proper. This function has two issues:
1) It only works if the DRAM size is a power of two. We start to see
boards which have 3GB of (usable) DRAM, so this does not fit anymore.
2) As U-Boot has no notion of reserved memory so far, it will happily
ride through the DRAM, possibly stepping on secure-only memory. This
could be a region of DRAM reserved for OP-TEE or some other secure
payload, for instance. It will most likely crash in that case.
As the SPL DRAM init routine has very accurate knowledge of the actual
DRAM size, lets propagate this wisdom to U-Boot proper.
We re-purpose a currently reserved word in our SPL header for that.
The SPL itself stores the detected DRAM size there, and bumps the SPL
header version number in that case. U-Boot proper checks for a valid
SPL header and a high enough version number, then uses the DRAM size
from there. If the SPL header field is not sufficient, we fall back to
the old DRAM scanning routine.
Part of the DRAM might be present and probed by SPL, but not accessible
by the CPU. They're restricted in the main U-Boot binary, when accessing
the DRAM size from SPL header.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
On Allwinner SoCs we use some free bytes at the beginning of the SPL image
to store various information. We have a version byte to allow updates,
but changing this always requires all tools to be updated as well.
Introduce the concept of semantic versioning [1] to the SPL header:
The major part of the version number only changes on incompatible
updates, a minor number bump indicates backward compatibility.
This patch just documents the major/minor split, adds some comments
to the header file and uses the versioning information for the existing
users.
[1] https://semver.org
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
This is required for the current Linux kernel to reboot. It should also
probably be fixed in Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the power domain DM driver for i.MX8, that it depends on the DTB
power domain trees to generate the power domain provider devices. Users
need to add power domain trees with property "compatible = "nxp,imx8-pd";"
When power on a PD device, the driver will power on its ancestor PD
devices in power domain tree.
When power off a PD device, the driver will check its child PD devices
first. Only if all child PD devices are off, then power off the current PD
device. Then the driver checks sibling PD devices. If sibling PD devices
are off, then it will power off parent PD device.
There is no counter maintained in this driver, but a state to hold current
on/off state. So the request and free functions are empty.
The power domain implementation in i.MX8 DTB set the "#power-domain-cells"
to 0, so there is no ID binding with each PD device. We don't use "id"
variable in struct power_domain. At the same time, we have to set of_xlate
to empty to bypass standard of_xlate in uclass driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This driver is mostly used to avoid build errors.
We use uclass clk driver for clk related operations.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
print_cpuinfo() in board init code requires uclass CPU driver,
add it to be able to display CPU info when CONFIG_DISPLAY_CPUINFO
option is enabled. CPU node in DT will have to include 'clocks'
and 'u-boot,dm-pre-reloc' properties for generic print_cpuinfo()
to work as expected. The driver outputs info for i.MX8QXP Rev A
and Rev B CPUs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add arch_cpu_init(_dm) mainly to open the channel between ACore and SCU.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add imx-regs header file to include the register base definition
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add clk/misc/pad/pm/rm scfw api implementaion for different
drivers to invoke. The low level code is using misc_call
to invoke imx8_scu driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add scu_dev for i.MX8, this will be used as a handle
to communite with SCU from A35.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds new zynqmp command "zynqmp tcminit mode" to
initialize TCM. TCM needs to be initialized before accessing
to avoid ECC errors. This new command helps to perform
the same. It also makes tcm_init() as global and uses it for
doing the TCM initialization.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add code to configure PLL4, from which the LDB clock are directly
derived.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The interruption support had be removed for ARM architecture and
the function get_timer_masked() is no more used except in some
the timer.c files.
This patch clean each timer.c which implement this function and
remove the associated prototype in u-boot-arm.h
For timer.c, I don't verify if the weak version of get_timer
(in lib/time.c) can be used
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The interruption support had be removed for ARM architecture and
the function udelay_masked() is no more used except in some timer.c
files and have the same content than udelay() or __udelay().
This patch update each timer.c implementing this function and
remove the associated prototype in u-boot-arm.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJbrkHRAAoJEO1FWZTaC520r3UQAIBntTglI1QK7YizVxZ1x9DL
42oSEIwkuN0wbndR7Jzx4EPPFJ8yX4v3stoxC3qS5DQ9kHMzuqRQcIDYbcn5Qy7Z
vd0mBUmpkRjr988pSaSHVQ8kPasncb545fCUumrXrCmhuG5Ea2Itw1zLdsTf7X5n
39KxFUOAR63BDCT0ZlR4VyMo01GxxHWCzRQH/rOWVzOcJsWF7R52hWIBBzVDxKPv
HF9SYaAB0PTFgSjJx5wYQ4xPdHVUp+svtYSJE8JYzEr/BvOVtL2iEi4t2rk19CrX
IaVMFydlv2iDgWdoSZFCCN/6lGDWSv1LWPDglWhLQhOYvrJOjZfgzzeAGU7wqoz4
JVjSLf6dHeOma55dbP/epDmyDFqWIfNOQ3uP4RM57xJ0PXQuT7ACVJctr6kHVTGL
1ZZxPdKSSf9lvtzoogPTTYRD5Ry7ud3sYZ0v3OHN1sbVcaHaVoHPeXeSz1sLg3Q+
zhUo1lXx4FcTz9R1fafdcqqAk/YGMZ7sBE+uYJPgExnApxrZID9IiOdGIBxo8jiK
ozLmaCIDqRyu/qhQW9WMri1tvYdKwq/739gBvvcIcrLR5RzfNUdwWjhtBokPQQnS
WZNqd3/0N8ZFGz7V0GOxCDnAo4nwQeZVFGMtTpoCtjPvr6DWBHsEUlQHTT3dQKz/
TXygMYUYGA+/vux0Dt4I
=XRFI
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch removes the support for 'invert' from the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reuse the existing ICID setup code done for LS1046A smmu enablement
and add the equivalent setup for LS1043A chips.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QMan IP block in this SoC is version 3.2 so advertise
this in the SoC configuration header.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch modifies PL bitstream loading sequence as per
latest Xilfpga which supports all variants of bitstream images
generated from vivado and from bootgen. With this new change in
Xilfpga, uboot doesn't need to validate and swap bitstream as it will
be taken care inside Xilfpga. ZynqMP PL driver now checks for supporting
PMUFW version before skipping the validation and swap sequence as there
can be old PMUFW which doesn't supports this feature. In this case, driver
uses old way of PL bitstream loading sequence.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify the zynqmp_pmufw_version() routine to return PMUFW version so
that it can be reused wherever required. Get PMUFW version from PMU
only once at bootup and later just return stored value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves the PM version related macros to .h file so that
they can be reused in other files.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Make use of asm-generic/atomic.h retaining the smp_mb_... definitions.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The MMC card detect pin is connected to gpio127 on omap3_logic.
When setting up the pbias register for MMC, let's also enable
gpio_127 for the card detect. As part of the package deal,
gpio_126 and gpio_129 are also enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
The SSP2 clock is at bit 6 in the register, so the value is 0x40 unlike
the current 0x70 which enables the clock of UART2, SSP1 and SSP2.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Stefan Roese <sr@denx.de>
SPI controllers SSP1, 2 and 3 require to enable their respective clocks.
Let's enable them only when the SPI controller driver is built.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
just try to bring up an imx6ull board with console
on uart5 and found, that input_val for pin
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX is 7 and
not 5 on imx6ull.
With this patch rx works now.
Signed-off-by: Heiko Schocher <hs@denx.de>
As no gpio.h is defined in arch/arm/mach-k3/include/,
to avoid compilation failure, do not include asm/arch/gpio.h.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM654 allows for booting from primary or backup boot media.
Both media can be chosen individually based on switch settings.
ROM looks for a valid image in primary boot media, if not found
then looks in backup boot media. In order to pass this boot media
information to boot loader, ROM stores a value at a particular
address. Add support for reading this information and determining
the boot media correctly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are multiple GPIOs that can be used with the same driver depending
on the CONFIG_GPIO_BASE defined in the controller driver.
GPIO3 and 4 require a clock to be enabled so let's enable them when the
driver is built.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
All architectures have the same definition for s8/16/32/64
and u8/16/32/64.
Factor out the duplicated code into <asm-generic/int-ll64.h>.
BTW, Linux unified the kernel space definition into int-ll64.h
a few years ago as you see in Linux commit 0c79a8e29b5f
("asm/types.h: Remove include/asm-generic/int-l64.h").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The existing imx_watchdog driver is compatible with mx25 chipsets.
Add a WDOG1_BASE_ADDR define for the base address and enable the driver
in watchdog's Makefile.
To use the driver, a board must define CONFIG_IMX_WATCHDOG and
CONFIG_HW_WATCHDOG.
This fixes an issue when booting an mx25 chip via usb/serial. In this
case, the boot rom will always enable the watchdog. If u-boot is running
in interactive mode and the watchdog is not serviced, the system is
rebooted when the watchdog expires.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In the current H6 CPU memory space code, the SUNXI in the macro name of
the SID address base is wrongly spelled as SNUXI, which leads to SID
readout not working.
Fix this macro name.
Fixes: 55f6b1c351c9 ("sunxi: add basic memory map definitions of H6 SoC")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
Program Central Security Unit (CSU) to grant access to USB 2.0
controller.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: rewrite commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Move ns_dev[] from header file to C file to avoid compiling warning
when header file is included by others.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: rewrite commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for SEC ICID configuration and apply it for ls1046a.
Also add code to make the necessary device tree fixups.
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for ICID setting of fman ports and the required device
tree fixups.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for ICID setting of qman portals and the required device
tree fixups. Also fix an endiness issue in portal setup code.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add infrastructure for ICID setup and device tree fixup on ARM
platforms. This include basic ICID setup for several devices.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add a define with a value for the missing debug stream ID.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QMAN_BAR{E} register setup was disabled on ARM platforms, however the
register does need to be set. Enable the code also on ARMs and fix the
CONFIG_SYS_QMAN_MEM_PHYS define to the correct value so that the newly
enabled code works.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QMan IP block in this SoC is version 3.2 so advertise
this in the SoC configuration header.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add defines for the edma and qdma register block base addresses.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This command is part of the write partition sequence performed by
rkdeveloptool: one partition is first completely erased and
than wrote.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch implement reading blocks form selected device with
LBA addressing.
Corresponding command on workstation is:
rkdeveloptool rl <start_blk> <blk_cnt> <file>
While we support reading more than one blocks per K_FW_LBA_READ_10
request, rkdeveloptool and original rockchip tool do perform
chunk reads limiting the maximum size per chunk far lower
than max int values.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Allwinner H6 SoC comes with a set of new DRAM controller+PHY combo.
Both the controller and the PHY seem to be originate from DesignWare,
and are similar to the ones in ZynqMP SoCs.
This commit introduces an initial DRAM driver for H6, which contains
only LPDDR3 support. The currently known SBCs with H6 all come with
LPDDR3 memory, including Pine H64 and several Orange Pi's.
The BSP DRAM initialization code is closed source and violates GPL. Code
in this commit is written by experimenting, referring the code/document
of other users of the IPs (mainly the ZynqMP, as it's the only found PHY
reference) and disassebling the BSP blob.
Thanks for Jernej Skrabec for review and fix some issues in this driver
(including the most critical one which made it to work), and rewrite
some code from register dump!
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC has 3 MMC controllers like the ones in A64, with
the MMC2 come with the capability to do crypto by EMCE.
Add MMC support for H6. EMCE support is not added yet.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The UART0 on H6 is available at PH bank (and PF bank, but the PF one is
muxed with SD card).
Add pinmux configuration.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The H6 SoC has a sun6i-style watchdog in its timer part.
Enable the usage of it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The new Allwinner H6 SoC has a brand new CCU layout.
Add clock code for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner H6 has a different RVBAR address with A64/H5.
Add conditional RVBAR configuration into the code which does RMR switch.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC come with a totally new memory map.
Add basical definition of the new memory map into a header file, and let
the cpu.h header include it in the situation of H6.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The new Allwinner H6 SoC has its SRAM A1 at neither 0x0 nor 0x10000, but
it's at 0x20000. Thus the SUNXI_HIGH_SRAM option needs to be refactored
to support this new configuration.
Change it to SUNXI_SRAM_ADDRESS, which holds the real address of SRAM
A1 in the memory map.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add a MON_MODE define for ARM's monitor mode. This can be used later by
a secure monitor to avoid hard-coding mode IDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
RAM repair has a few pre-requisites:
1) PMIC power supply (rail) enabled.
2) PMC CRAIL power partition powered.
3) Fuse clock active (it's the default).
4) PLLP reshift branch enabled (it's the default, when PLLP is active).
RAM repair also only need run whenever specific partitions are powered
(main SoC and CCPLEX respectively); RAM repair does not need to be
triggered when any other partition changes state.
start_cpu() needs to be re-ordered slightly to match these requirements.
Note that C0NC and CE0 aren't required for RAM repair to
operate, but they also do no harm, so the entire of powerup_cpus() is
moved rather than splitting it up. The call to remove_cpu_resets() is
moved last to ensure that all other actions complete before releasing
reset; since the PMC power partitions are now enabled early, releasing
reset is what causes the CPUs to start executing code, and RAM repair must
complete before the CPU boots.
Note that this commit is the result of squashing a numbmer of commits
in NVIDIA's downstream L4T branch, hence the multiple signoffs below.
Signed-off-by: Bibek Basu <bbasu@nvidia.com>
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This reverts commit 701b7b1d2c. It will
be immediately replaced by a different implementation that is more
complete and runs are more targetted times.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Remove the old implementation in order to enable DM for sata.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
The USBOH module on imx25 chips contains two USB controllers which are
called USB OTG Controller and USB Host Controller. Each one has its EHCI
root hub. The OTG Controller's EHCI registers start at offset 0, the Host
Controller's registers start at offset 0x400.
We set CONFIG_MXC_USB_PORT=0 to select the OTG Controller and 1 for the
Host Controller. Therefore, IMX_USB_PORT_OFFSET must be 0x400. Using
this setting, the Host Controller starts working on my imx25 board.
Please note that the imx25 reference manual claims that the Host
Controller's registers start at 0x200. This is not correct. The Linux
Kernel uses the correct offset 0x400 in imx25.dtsi.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Not all i.MX6 pads use the same drive strength table. So far only the
240 Ohm to 34 Ohm table was available. Because the constants used have
speaking names it can be confusing to use e.g. PAD_CTL_DSE_48ohm when
according to the reference manual 52 Ohm is the correct value. This
patch adds the 260 Ohm to 37 Ohm table.
For example, the IOMUXC_SW_PAD_CTL_PAD_SD2_CLK register (SD-card clock)
uses the added table.
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This macro allows to detect whether the boot ROM initialized USB
already (serial downloader). This is helpful to reliably detect
if the system has been recovered via USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Current implementation of find_next_zero_bit() is incompatible with arm64.
Hence fix it by using BITS_PER_LONG define instead of constants and
use generic ffz() implementation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Add clock control entries for the gigabit interface of the Allwinner
R40/V40 CPU
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Add compatible string for i.MX8 and move imx_lpi2c.h from mx7ulp directory
to u-boot include directory as a common header file.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This commit adds Actions Semi OWL family base clock and S900 SoC
specific clock support. For S900 peripheral clock support, only UART
clock has been added for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masking clock gate, reset register bits based on the
probed controller is proper only due to the assumption
that masking should start with 0 even thought the controller
has separate PHY or shared between OTG.
unfortunately these are fixed due to lack of separate
clock, reset drivers.
Say for example EHCI1 - EHCI3 in the datasheet (EHCI0 is for the OTG)
so we need to start reg_mask 0 - 2.
This patch calculated the mask, based on the register base
so that we can get the proper bits to set with respect to
probed controller.
We even do this masking by using PHY index specifier from dt,
but dev_read_addr_size is failing for 64-bit boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch update the USB PHY index for Allwinner H3.
Same change[1] initially sent, by 'Chen-Yu Tai' but missed
to apply due to recursive version changes on the same series.
[1] https://lists.denx.de/pipermail/u-boot/2018-January/318817.html
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Use the clk framework to initialize clocks from drivers that need them
instead of having hardcoded frequencies and initializations from board
code.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a basic clock driver for Amlogic Meson SoCs which supports
enabling/disabling clock gates and getting their frequency.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This undocumented function relies on arch-specific code to declare a nop
weak version. Add the weak function in common code instead to avoid having
to duplicate the same function in each arch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds support for loading secure bitstreams on ZynqMP
platforms. The secure bitstream images has to be generated using
Xilinx bootgen tool.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP emulation platforms are no longer tested and supported that's why
remove macros and code around.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Read reset reason reg and show it in log and also save it as variable.
Clearing reset reason when it is read to show only one status
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Allwinner PHY USB code is now part of generic-phy framework,
so drop existing legacy handling like arch/arm/mach-sunxi.c
and related code areas.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Clock gating bits on H43/H5 were wrong, fix them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
clock gating bits on a64 are different than H3_H5, so fixed
only required bits on clock_sun6i.h.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Remove harcoded XHCI lists and detect mode, speed based on DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Serial-changes: 2
- Remove also XHCI macros from hardware.h
- Remove additional new line in zcu106
Also remove the #ifdef's from clock.h since the Kconfig values defaults
the to old default values in clock.h.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit adds basic support for PWM found on Allwinner A64.
It can be used for pwm_backlight driver (e.g. for Pinebook)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
This patch fills the MMU map for DDR at run time based on information read
from Device Tree or automatically detected from static configuration.
The patch is needed because for systems which has for example 1GB of memory
but MMU map is 2GB there could be spurious accesses which was seen in past
when mapping is not fitting with actual memory installed.
Signed-off-by: Nitin Jain <nitin.jain@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
find_next_zero_bit() incorrectly handles cases when:
- total bitmap size < 32
- rest of bits to process
static inline int find_next_zero_bit(void *addr, int size, int offset)
{
unsigned long *p = ((unsigned long *)addr) + (offset >> 5);
unsigned long result = offset & ~31UL;
unsigned long tmp;
if (offset >= size)
return size;
size -= result;
offset &= 31UL;
if (offset) {
tmp = *(p++);
tmp |= ~0UL >> (32-offset);
if (size < 32)
[1]
goto found_first;
if (~tmp)
goto found_middle;
size -= 32;
result += 32;
}
while (size & ~31UL) {
tmp = *(p++);
if (~tmp)
goto found_middle;
result += 32;
size -= 32;
}
[2]
if (!size)
return result;
tmp = *p;
found_first:
[3] tmp |= ~0UL >> size;
^^^ algo can reach above line from from points:
[1] offset > 0 and size < 32, tmp[offset-1..0] bits set to 1
[2] size < 32 - rest of bits to process
in both cases bits to search are tmp[size-1..0], but line [3] will simply
set all tmp[31-size..0] bits to 1 and ffz(tmp) below will fail.
example: bitmap size = 16, offset = 0, bitmap is empty.
code will go through the point [2], tmp = 0x0
after line [3] => tmp = 0xFFFF and ffz(tmp) will return 16.
found_middle:
return result + ffz(tmp);
}
Fix it by correctly seting tmp[31..size] bits to 1 in the above case [3].
Fixes: 81e9fe5a29 ("arm: implement find_next_zero_bit function")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Taking into account the Amlogic Family name starts with GX, including
the GXBB, GXL and GXM SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Memory Protection Unit(MPU) allows to partition memory into regions
and set individual protection attributes for each region. In absence
of MPU a default map[1] will take effect. Add support for configuring
MPU on Cortex-R, by reusing the existing support for Cortex-M processor.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0460d/I1002400.html
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This function is no more used, and replaced by psci_save
which save also context id as requested by PSCI requirements.
Even if the context id is not used by Linux, it should be saved
and restored in r0 when the CPU_ON is performed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Save and use the 3rd parameter of PSCI CPU_ON request: context_id.
The context_id parameter is only meaningful to the caller.
U-Boot PSCI preserves a copy of the value passed in this parameter.
Following wakeup from a powerdown state, U-BOOT PSCI places
this value in R0 when it first enters the OS.
NB: this context id is not (yet?) used by Linux but it is mandatory
to be PSCI compliant.
update armv7 psci functions:
- psci_save_target_pc(): keep for backward compatibility with
current platform (only save PC and force context id to 0)
=> should be removed when all platform migrate to the new API
- psci_save(): new API to use by ARMv7 platform with PSCI,
save pc (= entry_point_address) and context_id
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
With full SPL enabled, the loaded image overwrites the mxs_spl_data
location. Moving it a slightly lower address fixes this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Working with HAB on the i.MX7 we've encountered a case where a board that
successfully authenticates u-boot when booting Linux via OPTEE subsequently
fails to properly bring up the RTC.
The RTC registers live in the low-power block of the Secure Non-Volatile
Storage (SNVS) block.
The root cause of the error has been traced to the HAB handing off the
SNVS-RTC in a state where HPCOMR::NPSWA_EN = 0 in other words where the
Non-Privileged Software Access Enable bit is zero. In ordinary
circumstances this is OK since we typically do not run in TZ mode, however
when we boot via HAB and enablng TrustZone, it is required to set
HPCOMR::NPSWA_EN = 1 in order for the upstream Linux driver to have
sufficient permissions to manipulate the SNVS-LP block.
On our reference board it is the difference between Linux doing this:
root@imx7s-warp-mbl:~# dmesg | grep rtc
snvs_rtc_enable read 0x00000000 from SNVS_LPLR @ 0x00000034
snvs_rtc_enable read 0x00000021 from SNVS_LPCR @ 0x00000038
snvs_rtc_enable read 0x00000000 from SNVS_HPLR @ 0x00000000
snvs_rtc_enable read 0x80002100 from SNVS_HPCOMR @ 0x00000004
snvs_rtc 30370000.snvs:snvs-rtc-lp: rtc core: registered
30370000.snvs:snvs-rtc-lp as rtc0
snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to2018-04-01 00:51:04 UTC (1522543864)
and doing this:
root@imx7s-warp-mbl:~# dmesg | grep rtc
snvs_rtc_enable read 0x00000000 from SNVS_LPLR @ 0x00000034
snvs_rtc_enable read 0x00000020 from SNVS_LPCR @ 0x00000038
snvs_rtc_enable read 0x00000001 from SNVS_HPLR @ 0x00000000
snvs_rtc_enable read 0x00002020 from SNVS_HPCOMR @ 0x00000004
snvs_rtc 30370000.snvs:snvs-rtc-lp: failed to enable rtc -110
snvs_rtc: probe of 30370000.snvs:snvs-rtc-lp failed with error -110
hctosys: unable to open rtc device (rtc0)
Note bit 1 of LPCR is not set in the second case and is set in the first
case and that bit 31 of HPCOMR is set in the second case but not in the
first.
Setting NPSWA_EN in HPCOMR allows us to boot through enabling TrustZone
and continue onto the kernel. The kernel then has the necessary permissions
to set LPCR::SRTC_ENV (RTC enable in the LP command register) whereas in
contrast - in the failing case the non-privileged kernel cannot do so.
This patch adds a simple init_snvs() call which sets the permission-bit
called from soc.c for the i.MX7. It may be possible, safe and desirable to
perform this on other i.MX processors but for now this is only tested on
i.MX7 as working.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Latest xilfpga expects to set BIT5 of flags for nonsecure
bitsream and also expects length in bytes instead of words
This patch does the same.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This inhibits the re-inititialization of DDR during an RTC-only resume. If
this is not done, an L3 NOC error is produced as the DDR gets accessed
before the re-init has time to complete. Tested on AM437x GP EVM.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[j-keerthy@ti.com Ported to Latest Master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.
The RTC scratch register layout used is:
SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader
During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.
RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add some clocks/PLL definitions as well as the dependency on MACH_SUN8I
in Kconfig.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
HW accelerated "hash sha256 ..." command doesn't work on i.MX6UL, we get
"CAAM was not setup properly or it is faulty" error message.
This is due to wrong CAAM base 0x02100000, on i.MX6UL the CAAM base
address is 0x02140000. Fix it.
Note: with this patch applied the "hash sha256" commant still has some
issues on i.MX6UL ("Invalid KEY Command" or other errors). With data
cache off the "hash sha256" command works as expected.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Clean the iomux definitions at grf_rk3188.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Clean the iomux definitions at grf_rk3036.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds support for the (to date unsupported) I2C controllers 1~4
and 6~7 (i.e. now all controllers except I2C5, which is not accessible
on the RK3399-Q7, are supported by pinctrl).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The shift values for GPIO2B1 and GPIO2B2 had in fact referred to
GPIO2B0 and GPIO2B1, respectively. This substitutes the correct
values.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds new command "zynqmp" to handle zynqmp
specific commands like "zynqmp secure". This secure command is
used for verifying zynqmp specific secure images. The secure
image can either be authenticated or encrypted or both encrypted
and authenticated. The secure image is prepared using bootgen
and will be in xilinx specific BOOT.BIN format. The optional
key can be used for decryption of encrypted image if user
key was specified while creation BOOT.BIN.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable all types of non-secure access to PFE block registers.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
1. Set AWCACHE0 attribute of PFE DDR and HDBUS master interfaces
to bufferable.
2. Set RD/WR QoS for PFE DDR and HDBUS AXI master interfaces.
3. Disable ECC detection for PFE.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
SoC specific PFE macros are defined and structure ccsr_scfg
is updated with members defined for PFE.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Layerscape Gen2 SoC supports GPIO registers to control GPIO
signals. Adding support of GPIO structure to access GPIO
registers.
Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove arch/arm/include/asm/arch-stm32fx/stm32_periph.h
as all defines or enums are no more used.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
For STM32F4 and F7 SoCx family, a specific stm32.h file exists.
Some common defines are duplicated or even unused in each of
these stm32.h.
Factorize all common definition in arch/arm/include/asm/stm32f.h and keep
specific definitions in each arch/arm/include/asm/arch-stm32fx/stm32.h.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Instead to have 3 identical gpio.h for all STM32 SoCs,
migrate them in one file in include/asm.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
fmc.h file is no more used, remove it.
All FMC related defines are declared in drivers/ram/stm32_sdram.c
which is common to all STM32 SoCs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.
Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx
Enable DM STM32_TIMER for STM32F4/F7 and H7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
commit ed286bc80e ("imx: hab: Check if CSF is valid before authenticating
image") makes use of "__packed" as a prefix to the "struct hab_hdr"
declaration.
With my compiler "gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)" we
get:
./arch/arm/include/asm/mach-imx/hab.h:42:25: error: expected ‘=’, ‘,’, ‘;’,
‘asm’ or ‘__attribute__’ before ‘{’ token
struct __packed hab_hdr {
Fix this problem by including <linux/compiler.h>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.
This saves around 740 bytes for the am335x_evm SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently the following devices are using a different definition for ROM
Vector Table addresses:
- i.MX6DQP = All rev
- i.MX6DQ >= rev 1.5
- i.MX6SDL >= rev 1.2
There is no need to create a new RVT macros since the only update were the
RVT base address. Remove HAB_RVT_*_NEW macros and define a new RVT base
address.
More details about RVT base address can be found on processors Reference
Manual and in the following documents:
EB803: i.MX 6Dual/6Quad Applications Processor Silicon Revision 1.2 to 1.3
Comparison
EB804: i.MX 6Solo/6DualLite Application Processor Silicon Revision 1.1
to 1.2/1.3 Comparison
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Write, Check and Set MID commands have been deprecated from the Code
Signing Tool (CST) v2.3.3 and will not be implemented in newer versions
of HAB, hence the following features are no longer available:
- Write Data
- Clear Mask
- Set Mask
- Check All Clear
- Check All Set
- Check Any Clear
- Check Any Set
- Set MID
The inappropriate use of Write Data command may lead to an incorrect
authentication boot flow. Since no specific application has been identified
that requires the use of any of these features, it is highly recommended to
add this check.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
For proper authentication the HAB code must check if the CSF is valid.
Users must call the csf_is_valid() function to parse the CSF prior to
authenticating any additional images. The function will return a failure
if any of the following invalid conditions are met:
- CSF pointer is NULL
- CSF Header does not exist
- CSF does not lie within the image bounds
- CSF command length zero
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Now that omap_hsmmc has support for hs200 mode, change the clock
frequency to 192MHz. Also change the REFERENCE CLOCK frequency to
192MHz based on which the internal mmc clock divider is calculated.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
I/O data lines of UHS SD card operates at 1.8V when in UHS speed
mode (same is true for eMMC in DDR and HS200 modes). Add support
to switch signal voltage to 1.8V in order to support
UHS cards and eMMC HS200 and DDR modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0. These values are populated in device tree. Add
capability in omap_hsmmc driver to extract IOdelay values for different
silicon revision. The maximum frequency is also reduced when using a ES1.1.
To keep the ability to boot both revsions with the same dtb, those values
can be provided by the platform code.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.
The DCRC interrupt, occurs when the last tuning block fails
(the last ratio tested). The delay from CRC check until the
interrupt is asserted is bigger than the delay until assertion
of the tuning end flag. Assertion of tuning end flag is what
masks the interrupts. Because of this race, an erroneous DCRC
interrupt occurs.
The suggested workaround is to disable DCRC interrupts during
the tuning procedure which is implemented here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the internal DLL.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the timing parameter set in the MMC core to set the
mode in UHSMS bit field. This is in preparation for
adding HS200 support in omap hsmmc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
be used irrespective of setting the clock (For example during iodelay
recalibration).
Also set the clock only if there is a change in frequency.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
We should take the MX6DP and MX6QP options in consideration
in the I2C_PADS_INFO macro.
Based on a patch by Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
We should take the MX6DP and MX6QP options in consideration
when defining imx_iomux_v3_setup_pad().
Based on a patch by Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
SION bit should be used in the situation that we need
to read back the value of a pin and should not be set by
default macro.
We get some malfunction as raised by following thread
https://www.spinics.net/lists/linux-usb/msg162574.html
As reported by this application note:
https://www.nxp.com/docs/en/application-note/AN5078.pdf
The software input on (SION) bit is an option to force an input
path to be active regardless of the value driven by the
corresponding module. It is used when the nature direction
of a pin depending on selected alternative function is an output,
but it is needed to read the real logic value on a pin.
The SION bit can be used in:
• Loopback: the module of a selected alternative function drives
the pad and also receives the pad value as an input
• GPIO capture: the module of a selected alternative function
drives the pin and the value is captured by the GPIO
SION bit is not necessary when the pin is configured as a peripheral
apart specific silicon bug. If an application needs to have this
set, this should be done in board file or in dts file
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Include i.MX8M in lcdif register layout map.
Also included i.MX7ULP in this patch, since share same with i.MX8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Move i.MX6/7 bootaux code to imx_bootaux.c.
The i.MX6/7 has different src layout, so define M4 reg offset
to ease the cleanup. Redefine the M4 related BIT for share
common code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Add SiP (Silicon Provider) services function to issue
SMC call to Arm Trusted Firmware.
More SiP information could be found in
https://github.com/ARM-software/arm-trusted-firmware/blob/master/
docs/arm-sip-service.rst
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add clock driver to support i.MX8M.
There are two kind PLLs, FRAC pll and SSCG pll. ROM already
configured SYS PLL1/2, we only need to configure the output.
ocotp/i2c/pll decoding and configuration/usdhc/lcdif/dram pll/
enet clock are configured in the code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
Move generic functions to common location psu_spl_init.c. Function
declarations are added to private header.
These changes are done in connection to the fact that still files from
HDF can be copied over and compilation should pass.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psu_init() returns int which wasn't declared and checked.
The patch is fixing function declarations and code to handle return
values properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Implement the setting parent for gmac clock, and add internal
pll div set for mac clk.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Clean the iomux definitions at grf_rk322x.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
After that, define the uart2 iomux at rk322x-board file.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Need to set gmac m1 pins iomux, gmac m0 tx pins, select bit2
and bit10 at com iomux register. After that, set rgmii m1 tx
pins to 12ma drive-strength, and clean others to 2ma.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Clean the iomux definitions at grf_rk3328.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If we include both the rk3288_grf.h and rv1108_grf.h, it will cause the
conflicts of redefinition. Clean the iomux definitions at grf_rv1108.h,
and move them into pinctrl-driver.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The last 4 grf registers offset of rv1108 are wrong, fix them
for correct usage.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Move SYSCFG clock setup into configure_clocks() instead of calling
clock_setup() from board file.
As this clock is only needed in case of ethernet enabled and as
both stm32f4 and stm32f7 are using the Designware ethernet IP,
we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed.
Move the RMII setup from board_early_init_f() to board_init()
to insure that RMII bit is set only when clock driver is initialized.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Thanks to 'commit ba1f966725 ("net: designware: add clock support")'
we don't need anymore to setup the STMMAC clock in board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Erratum NO. FE-9144572: The device SPI interface supports frequencies of
up to 50 MHz. However, due to this erratum, when the device core clock
is 250 MHz and the SPI interfaces is configured for 50MHz SPI clock and
CPOL=CPHA=1 there might occur data corruption on reads from the SPI
device.
Implement the workaround by setting the TMISO_SAMPLE value to 0x2
in the timing1 register.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Restructures common driver to support LTC3882 voltage regulator
chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds SERDES voltage and reset SERDES lanes API and makes
enable/disable DDR controller support 0.9V API common.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPs
Both the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Keystone and DRA7 based TI platforms uses same
EMIF memory controller. cmd_ddr3 command is customized
for keystone platforms, make it generic so that it can
be re used for DRA7 platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
For data integrity, the EMIF1 supports ECC on the data
written or read from the SDRAM. Add support for enabling
ECC support in EMIF1.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
This is a slight difference in emif_ddr_phy_status register offsets for
DRA7xx EMIF and older versions. And ecc registers are available only
in DRA7xx EMIC. Add support for this difference and ecc registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for simple memory fill operation. With large data sizes
it is much faster to use EDMA for memory fill rather than CPU.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance
to use if any at all is done through
CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is
handled in U-boot. Handle this additional pinmuxing requirement in U-boot
to ensure that MCAN is used by default via the DCAN1 pins.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
omap_hsmmc driver uses "|" in a couple of places for disabling a bit.
While it's okay to use it in "mmc_reg_out" (since mmc_reg_out has a
_mask_ argument to take care of resetting a bit), it's incorrectly used
for resetting flags in "omap_hsmmc_send_cmd".
Fix it here by using "&= ~()" to reset a bit.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The omap hsmmc host controller can have the ADMA2 feature. It brings better
read and write throughput.
On most SOC, the capability is read from the hl_hwinfo register. On OMAP3,
DMA support is compiled out.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Align the base address defined in header files with the base address used
in the DTS. This will facilitate the introduction of the DMA support.
Of all HSMMC users, only omap3 doesn't have the 0x100 reserved region at
the top. This region will be used to determine if the controller supports
DMA transfers
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reverts commit 46831c1a4c.
This reserved area at the beginning of struct hsmm, will be used later to
support ADMA
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The hab_rvt_failsafe() callback according to the HABv4 documentation:
"This function provides a safe path when image authentication has failed
and all possible boot paths have been exhausted. It is intended for use by
post-ROM boot stage components, via the ROM Vector Table."
Once invoked the part will drop down to its BootROM USB recovery mode.
Should it be the case that the part is in secure boot mode - only an
appropriately signed binary will be accepted by the ROM and subsequently
executed.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
It will be helpful to boot commands to know if the HAB is enabled. Export
imx_hab_is_enabled() now to facilitate further work with this data-point in
a secure-boot context.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tidy up the HAB namespace a bit by prefixing external functions with
imx_hab. All external facing functions past this point will be prefixed in
the same way to make the fact we are doing IMX HAB activities clear from
reading the code. authenticate_image() could mean anything
imx_hab_authenticate_image() is on the other hand very explicit.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The hab_rvt_check_target() callback according to the HABv4 documentation:
"This function reports whether or not a given target region is allowed for
either peripheral configuration or image loading in memory. It is intended
for use by post-ROM boot stage components, via the ROM Vector Table, in
order to avoid configuring security-sensitive peripherals, or loading
images over sensitive memory regions or outside recognized memory devices
in the address map."
It is a useful function to support as a precursor to calling into
authenticate_image() to validate the target memory region is good.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The various i.MX BootROMs containing the High Assurance Boot (HAB) block
rely on a data structure called the Image Vector Table (IVT) to describe to
the BootROM where to locate various data-structures used by HAB during
authentication.
This patch adds a definition of the IVT header for use in later patches,
where we will break the current incorrect dependence on fixed offsets in
favour of an IVT described parsing of incoming binaries.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
u-boot command "hab_auth_img" tells a user that it takes
- addr - image hex address
- offset - hex offset of IVT in the image
but in fact the callback hab_auth_img makes to authenticate_image treats
the second 'offset' parameter as an image length.
Furthermore existing code requires the IVT header to be appended to the end
of the image which is not actually a requirement of HABv4.
This patch fixes this situation by
1: Adding a new parameter to hab_auth_img
- addr : image hex address
- length : total length of the image
- offset : offset of IVT from addr
2: Updates the existing call into authenticate_image() in
arch/arm/mach-imx/spl.c:jump_to_image_no_args() to pass
addr, length and IVT offset respectively.
This allows then hab_auth_img to actually operate the way it was specified
in the help text and should still allow existing code to work.
It has the added advantage that the IVT header doesn't have to be appended
to an image given to HAB - it can be prepended for example.
Note prepending the IVT is what u-boot will do when making an IVT for the
BootROM. It should be possible for u-boot properly authenticate images
made by mkimage via HAB.
This patch is the first step in making that happen subsequent patches will
focus on removing hard-coded offsets to the IVT, which again is not
mandated to live at the end of a .imx image.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
CSF_PAD_SIZE should be defined in hab.h, move it to that location now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The size of the IVT header should be defined in hab.h move it there now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Both usages of authenticate_image treat the result code as a simple binary.
The command line usage of authenticate_image directly returns the result
code of authenticate_image as a success/failure code.
Right now when calling hab_auth_img and test the result code in a shell a
passing hab_auth_img will appear to the shell as a fail.
The first step in fixing this behaviour is to fix-up the result code return
by authenticate_image() itself, subsequent patches fix the interpretation
of authenticate_image so that zero will return CMD_RET_SUCCESS and non-zero
will return CMD_RET_FAILURE.
The first step is fixing the return type in authenticate_image() so do that
now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Allow placing a Linux kernel image header at the start of the U-Boot
binary. This is useful since the image header reports the amount of memory
(BSS and similar) that U-Boot needs to use, but that isn't part of the
binary size. This can be used by the code that loads U-Boot into memory to
determine where to load U-Boot, based on other users of memory.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware
- Create new board/freescale/common/fsl_portals.c to house shared
device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
setup to disable interrupts on all QMan and BMan portals. It is
needed because the interrupts are enabled by default for all portals
including unused/uninitialised portals. When the kernel attempts to
go to deep sleep the unused portals prevent it from doing so
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sata registers PP2C and PP3C are used to control the configuration
of the PHY control OOB timing for the COMINIT/COMWAKE parameters
respectively. Calculate those parameters from port clock frequency.
Overwrite those registers with calculated values to get better OOB
timing.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use available DM stm32f7_gpio.c and pinctrl_stm32.c drivers
instead of board GPIO initialization.
Remove stm32_gpio.c which is no more used and migrate
structs stm32_gpio_regs and stm32_gpio_priv into
arch-stm32f4/gpio.h to not break compilation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM clk_stm32f.c driver instead of dedicated
mach-stm32/stm32f4/clock.c.
Migrate periph_clock defines from stm32_periph.h directly in
CLK driver. These periph_clock defines will be removed when STMMAC,
TIMER2 and SYSCFG drivers will support DM CLK.
Enable also CLK flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove serial_stm32.c driver and uart init from board file,
use available DM serial_stm32x7.c driver compatible for
STM32F4/F7 and H7 SoCs.
The serial_stm32x7.c driver will be renamed later with a more
generic name as it's shared with all STM32 Socs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
this patch implement rockusb protocol on the device side. this is based on
USB download gadget infrastructure. the rockusb function implements the rd,
wl, rid commands. it can work with rkdeveloptool
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bind rockchip reset to clock-controller with rockchip_reset_bind().
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The i.MX 6UL/ULL feature a Cortex-A7 CPU which suppor the ARM
generic timer. This change makes use of the ARM generic timer in
U-Boot.
This is crucial to make the ARM generic timers usable in Linux since
timer_init() initalizes the system counter module, which is necessary
to use the generic timers CP15 registers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Since commit 051ba9e082 ("Kconfig: mx6ull: Deselect MX6UL from
CONFIG_MX6ULL") CONFIG_MX6ULL does not select CONFIG_MX6UL anymore, so
take this into consideration in all the checks for CONFIG_MX6UL.
This fixes a boot regression.
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Breno Lima <breno.lima@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
commit 20f1471416 ("imx: spl: Update NAND bootmode detection bit")
broke the NAND bootmode detection by checking if
BOOT_CFG1[7:4] == 0x8 for NAND boot mode.
This commit essentially reverts it, while using the IMX6_BMODE_*
macros that were introduced since.
Tables 8-7 & 8-10 from IMX6DQRM say the NAND boot mode selection
is done when BOOT_CFG1[7] is 1, but BOOT_CFG1[6:4] is not
necessarily 0x0 in this case.
Actually, NAND boot mode is when 0x8 <= BOOT_CFG1[7:4] <= 0xf,
like it was in the code before.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tim Harvey <tharvey@gateworks.com>
NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.
Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Rockchip SoCs only need boot0 hook at SPL, and the U-Boot proper do not
need it.
The very beginning of U-Boot proper is different between armv7 and armv8:
armv7 start with ARM_VECTORS while armv8 start with 'b reset'.
Here is the map of very beginning for all cases:
armv7 SPL: TAG(overwrite 'b 1f')+'b reset' + ARM_VECTORS
armv7 U-Boot: ARM_VECTORS
armv8 SPL: TAG(overwrite 'b 1f')+'b reset' + Reserved_iram(rk3399)
armv8 U-Boot: 'b reset'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add missing zynq_board_read_rom_ethaddr() prototype reported by sparse.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Check LS1043A/LS2080a by device ID without using personality ID to
determine revision number. This check applies to all various
personalities of the same SoC family.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
These ifdefs are protecting #include statements for files that have
never existed. AFAICT this hardware.h has been copied from the kernel
and the ifdefs have never served a role in U-Boot, so delete them.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
To page mapping the lowest 2 bits needs to be 0x3.
If not fix this, the final lowest 3 bits for page mapping is 0x1
which is marked as reserved.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.
But mainline U-Boot and Linux has the old address and size fixed.
These SoCs have a register interface to get the two firmware reserved
memory start and sizes.
This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.
Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html
Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()
Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception
Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce a generic common Ethernet Hardware init function
common to all Amlogic GX SoCs with support for the
Internal PHY enable for GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This header was renamed to rawnand.h in Linux.
The following is the corresponding commit in Linux.
commit d4092d76a4a4e57b65910899948a83cc8646c5a5
Author: Boris Brezillon <boris.brezillon@free-electrons.com>
Date: Fri Aug 4 17:29:10 2017 +0200
mtd: nand: Rename nand.h into rawnand.h
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DCLK_VOP_DIV_CON_MASK should cover only bits 8 through 15.
Fix this to remove an "integer-overflow on shifted constant" warning.
Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The PLL selector field for NANDC is only 2 bits wide.
This fixes an 'int-overflow on shift' warning.
Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add rk3128 pinctrl driver and grf/iomux structure definition.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add rk3128 clock driver and cru structure definition.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
In order to factorize code between STM32F4 and STM32F7
migrate all structs related to RCC clocks in include/stm32_rcc.h
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.
STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
STM32F4 doesn't get rcc.h file, to avoid compilation
issue, migrate RCC related defines from rcc.h to driver
file and remove rcc.h file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
PWR IP is used to enable over-drive feature in
order to reach a higher frequency.
Get its base address from DT instead of hard-coded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAloeqWoACgkQykllyylKDCHO1wCggsSgQqOPdCo207FqI3yj2p0E
MYkAoI1wKvQcjGJJY19YEC1r70Op8RNo
=BqNN
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.01' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.1
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
Same macros are defined in various places. Collect them into
include/linux/bitops.h like Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Version string has unused fields 31:20 which can be used for exporting 9
bits from efuse IPDISABLE regs to recognize eg/cg/ev devices.
These efuse bits are setup for certain devices.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch provides a Kconfig option to use specified
memory for MMU table using reserve_mmu platform specific
routine. Here we used TCM space for MMU table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.
It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.
While at it, rename it to imx_wdog_disable_powerdown().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this
into account in the base address definition.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The RK3399 has a total of 9 I2C controllers. To support these, the
enum in periph.h is extended and the mapping from the IRQ numbers to
the peripheral-ids is extended to ensure that pinctrl requests are
passed through to the function configuring the I2C pins.
For I2C8, the pinctrl is implemented and tested (on a RK3399-Q7) using
communication with the FAN53555 connected on I2C8.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Rockchip bootrom will enter download mode if it returns from
spl/tpl with a non-zero value and couldn't find a valid image
in the backup partition.
This patch provide a method to instruct the system to back to
bootrom download mode by checking the BROM_DOWNLOAD_FLAG register.
As the bootrom download function relys on some modules such as
interrupts, so we need to back to bootrom as early as possbile
before the tpl/spl code override the interrupt configurations.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
setup_boot_mode function use the same logic but different
mode register address across all the rockchip platforms,
so it's better to make this function reused across all the
platforms, and let the mode register address setting from
the config file.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use a common driver for all Rockchip SOC instead of one for each SoC.
Use driver_data for reg offset.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The BROM supports forcing it to enter download-mode, if an appropriate
result/cmd-word is returned to it. There already is a series to
support this in review, so this prepares the (newly C-version) of the
back-to-bootrom code to accept a cmd to passed on to the BROM.
All the existing call-sites are adjusted to match the changed function
signature.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
The back-to-bootrom implementation for Rockchip has always relied on
the stack-pointer being valid on entry, so there was little reason to
have this as an assembly implementation.
This provides a new C-only implementation of save_boot_params and
back_to_bootrom (relying on setjmp/longjmp) and removes the older
assembly-only implementation.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
The previous setjmp-implementation (as a static inline function that
contained an 'asm volatile' sequence) was extremely fragile: (some
versions of) GCC optimised the set of registers. One critical example
was the removal of 'r9' from the clobber list, if -ffixed-reg9 was
supplied.
To increase robustness and ensure PCS-compliant behaviour, the setjmp
and longjmp implementation are now in assembly and closely match what
one would expect to find in a libc implementation.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
The save_boot_params_ret() prototype (for those of us, that have a
valid SP on entry and can implement save_boot_params() in C), was
previously only defined for !defined(CONFIG_ARM64).
This moves the declaration to a common block to ensure the prototype
is available to everyone that might need it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Some Rockchip BROM versions (e.g. the RK3188 and RK3066) first read 1KB data
from NAND into SRAM and executes it. Then, following a return to bootrom, the
BROM loads additional code to SRAM (not overwriting the first block read) and
reenters at the same address as the first time.
To support booting either a TPL (on the RK3066) or SPL (on the RK3188) using
this model of having to count entries, this commit adds code to the boot0
hook to track the number of entries and handle them accordingly.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
This updates the BCM281xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This updates the BCM235xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 5
- ran 'whitespace-cleanup'
The '_start' is using as vector table base address, and will write
to VBAR register, so it needs to be aligned to 0x20 for armv7.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated to current code base:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The boot0 hook on ARM does not insert its payload before the vector
table. This is both a mismatch with thec comment above it and
contradict usage of the boot0 hook on ARM64.
To fix this (and unify the semantics for ARM and ARM64), we change the
boot0-hook semantics on ARM to match those on ARM64:
(1) if a boot0-hook is present it is inserted at the start of
the image
(2) if a boot0-hook is present, emitting the ARM vector table
(and the _start) symbol are suppressed in vectors.S and
the boot0-hook has full control over where and when it
wants to emit these
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a driver for the I2C controller available on Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
UARTs 1 through 5 were missing in the code - added.
Also pick the default according to the configuration setting for the
console index.
Signed-off-by: Ronald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers
were added to configure the internal RMII PHY interface.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for the latest MX6QP wandboard variant.
Based on Richard Hu's work from Technexion's U-Boot tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Enable support for loadables in SEC firmware FIT image. Currently
support is added for single loadable image.
Brief description of implementation:
Add two more address pointers (loadable_h, loadable_l) as arguments to
sec_firmware_init() api.
Create new api: sec_firmware_checks_copy_loadable() to check if loadables
node is present in SEC firmware FIT image. If present, verify loadable
image and copies it to secure DDR memory.
Populate address pointers with secure DDR memory addresses where loadable
is copied.
Example use-case could be trusted OS (tee.bin) as loadables node in SEC
firmware FIT image.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Change DDR allocated for secure memory from 2 MB to 66 MB. This
additional 64 MB secure memory is required for trusted OS running
in Trusted Execution Environment using ARMv8 TrustZone.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As explained in arch/arm/mach-sunxi/clock_sun8i_a83t.c, clk for CPU
clusters is computed as clk = 24*n. However, the current formula is clk
= 24*(n-1).
This results in a clock set to a frequency that isn't specified as
possible for CPUs.
Let's use the correct formula.
Fixes: f542948b1e ("sunxi: clk: add basic clocks for A83T")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When compiling with W=1 errors are observed:
drivers/pci/pcie_imx.c:517:12: warning: no previous prototype for ‘imx6_pcie_toggle_power’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_power(void)
drivers/pci/pcie_imx.c:528:12: warning: no previous prototype for ‘imx6_pcie_toggle_reset’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_reset(void)
Remove these warnings by adding the functions prototypes on arch-mx6/sys_proto.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
When compiling with W=1 the following warning is observed:
arch/arm/mach-imx/mx6/clock.c:1268:5: warning: no previous prototype for ‘do_mx6_showclocks’ [-Wmissing-prototypes] int do_mx6_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
Remove this warning by adding the function prototype into arch-mx6/clock.h file.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
The configuration files imximage.cfg are used for the DDR controller
configuration.
Add DDR configuration function to replace the DDR controller
configuration in the imximage.cfg file. The function can be used for
DDR size detection.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
The CCM_ macros use the CCM_BASE_ADDRESS macro, which doesn't exist.
Replace the CCM_BASE_ADDRESS macros with CCM_BASE_ADDR.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
When compiling with W=1 the following warning is observed:
board/freescale/mx6sabresd/mx6sabresd.c:266:5: warning:
no previous prototype for ‘board_mmc_get_env_dev’
[-Wmissing-prototypes] int board_mmc_get_env_dev(int devno)
Remove this warning by adding the function prototype into sys_proto.h file.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add jump_to_image_linux() for arm64. Add "noreturn" flag to
armv8_switch_to_el2(). Add hooks to fsl-layerscape to enable falcon
boot.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Tested-by: Łukasz Majewski <lukma@denx.de>
macro branch_if_master checks master CPU via (Aff3 & (Aff2:Aff1:Aff0))
it is simple but a little obscure.
fix by checking Affx fields within MPIDR_EL1 directly.
Signed-off-by: zijun_hu <zijun_hu@htc.com>
U-Boot itself might need to identify the boot device, for example to be
able to tell where to load the kernel from when several options are
possible.
Move the logic of spl_boot_device to a function that is compiled both for
the SPL and the main binary.
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The device model was implemented so far using a hook that needed to be
called from the board support, without DT support and only for the host.
Switch to probing both in peripheral and host mode through the DT.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the arm architecture to make use of the new asm-generic/io.h to
provide address mapping functions. As the generic implementations are
suitable for arm this is primarily a matter of removing code.
This has only been build-tested, feedback from architecture maintainers
is welcome.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Rockchip BROM allows reading where it booted from from SRAM.
This adds the necessary definitions (as received from Kever) for
the location of this information in the RK3399's SRAM and naming
for the constants used.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
configure_l2ctlr will be shared between SPL and TPL so
move them into asm/arch/sys_proto.h
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
L2CTLR read/write functions are common to armv7 so, move
them in to include/asm/armv7.h and use them where ever it need.
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Backed out the change to arch/arm/mach-tegra/cache.c:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Some of macros definition are not correct, fix them according to TRM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add driver for rk322x to support sdram initialize in SPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 8-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 10-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.
For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.
Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Unfortunately, the integrated macphy default is enabled, which will
increase power consuming, if we do not use this PHY. So let's disable
it at first, which will save power consuming. If we really use it, then
enable it in driver level.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Update these macros to use all upper-case to avoid checkpatch
warnings:
ENET_25MHz,
ENET_50MHz,
ENET_125MHz,
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This macro allows to detect whether the USB PHY is active. This
is helpful to detect if the boot ROM has previously started the
USB serial downloader.
The idea is taken from the mfgtool support in the NXP U-Boot:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/?h=imx_v2016.03_4.1.15_2.0.0_ga&id=a352ed3c5184b95c4c9f7468f5fbb5f43de5e412
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Commit 6ae4c3efbd ("ARM: DRA7: Add pinctrl register definitions")
has added new macros for pinmux configuration in line with the kernel
definitions. Cleanup the old pinctrl macros from the common header
file so that they are not used by any new boards.
Signed-off-by: Suman Anna <s-anna@ti.com>
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add space around operator "+", make it
match the coding style.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Macro VA_BITS and PTE_BLOCK_BITS are not used
in the code, so remove them.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 1 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN
Adding CPU detection support for the dra76 ES1.0 soc
and update prcm, control module, dplls data.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The pcie config space of ls1088a is different from ls2080a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Singaling (LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receive
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter
settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for RGMII protocol
NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For QSPI and IFC addresses execution shouldn't be allowed
when u-boot running from DDR. Revise the MMU final table
to enforce execute-never bits.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Unify memory map for Layerscape based platforms. This patch includes
changes in bootscript, bootscript header and PPA header addresses
change as per unified memory map.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.
This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
Sometimes it's helpful to know the reset reason caused in the SoC.
Add reset reason detection for the RK3288 SoC.
This will set an environment variable which represents the reset reason.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_BUS_MAX
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix AM43XX drop AM44XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
For consistency with other platforms and in preparation of Kconfig
migration, let's change Several TI platforms that use I2C_BUS_MAX
to CONFIG_SYS_I2C_BUS_MAX
Signed-off-by: Adam Ford <aford173@gmail.com>
SUNXI_GMAC was still used to configure the code where as the
same has been renamed and moved to Kconfig in below commit
"sunxi: Move SUNXI_GMAC to Kconfig"
(sha1: 4d43d065db)
Signed-off-by: Dave Prue <dave@prue.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
[Tweek commit message, config_whitelist.txt, build-whitelist.sh]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Almost all of the newer Allwinner SoCs have a new operating mode for the
eMMC clocks that needs to be enabled in both the clock and the MMC
controller.
Details about that mode are sparse, and the name itself (new mode vs old
mode) doesn't give much details, but it seems that the it changes the
sampling of the MMC clock. One side effect is also that it divides the
parent clock rate by 2.
Add support for it through a Kconfig option.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D,
MX6Q and MX6QP processors move it to the soc.c file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
kASLR support in kernel requires a random number to be passed via
chosen/kaslr-seed propert. sec_firmware generates this random seed
which can then be passed in the device tree node.
sec_firmware reserves JR3 for it's own usage. Node for JR3 is
removed from device-tree.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Add the reserved boot mode used in the bmode command for i.MX 6UL
and 6ULL as introduced in commit 3fd9579085 ("imx: mx6ull: fix USB
bmode for i.MX 6UL and 6ULL").
Also replace BMODE_UART with BMODE_RESERVED, which is more appropriate.
Commit 96aac843b6 ("imx: Use IMX6_BMODE_* macros instead of numericals")
added macros for boot modes, in the process the reserved boot mode got
named BMODE_UART. We use the reserved boot mode in the bmode command to
let the boot ROM enter serial downloader recovery mode. But this is only
a side effect, the actual boot mode is reserved...
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Some files for i.MX do not yet have the SPDX ID to reference the correct
license.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Wolfgang Denk <wd@denx.de>
The description for eMMC/SDIO/SDMMC src is not correct,
update the CRU_CLKSEL11_CON value definition according to TRM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
A few years ago STM32F1 SoCs support has been added :
0144caf22c gpio: stm32: add stm32f1 support
2d18ef2364 ARMv7M: add STM32F1 support
But neither STM32F1 dedicated defconfig nor board was
associated to these commits.
Got confirmation from Tom Rini and Matt Porter to remove
all this code [1]
[1] http://u-boot.10912.n7.nabble.com/Remove-STM32F1-support-td301603.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
OMAP5432 did go into production with AVS class0 registers which were
mutually exclusive from AVS Class 1.5 registers.
Most OMAP5-uEVM boards use the pre-production Class1.5 which has
production efuse registers set to 0. However on production devices,
these are set to valid data.
scale_vcore logic is already smart enough to detect this and use the
"Nominal voltage" on devices that do not have efuse registers populated.
On a test production device populated as follows:
MPU OPP_NOM:
=> md.l 0x04A0021C4 1
4a0021c4: 03a003e9 ....
(0x3e9 = 1.01v) vs nom voltage of 1.06v
MPU OPP_HIGH:
=> md.l 0x04A0021C8 1
4a0021c8: 03400485 ..@.
MM OPP_NOM:
=> md.l 0x04A0021A4 1
4a0021a4: 038003d4 ....
(0x3d4 = 980mV) vs nom voltage of 1.025v
MM OPP_OD:
=> md.l 0x04A0021A8 1
4a0021a8: 03600403 ..`.
CORE OPP_NOM:
=> md.l 0x04A0021D8 1
4a0021d8: 000003cf ....
(0x3cf = 975mV) vs nom voltage of 1.040v
Since the efuse values are'nt currently used, we do not regress on
existing pre-production samples (they continue to use nominal voltage).
But on boards that do have production samples populated, we can leverage
the optimal voltages necessary for proper operation.
Tested on:
a) 720-2644-001 OMAP5UEVM with production sample.
b) 750-2628-222(A) UEVM5432G-02 with pre-production sample.
Data based on OMAP5432 Technical reference Manual SWPU282AF (May
2012-Revised Aug 2016)
NOTE: All collaterals on OMAP5432 silicon itself seems to have been
removed from ti.com, though EVM details are still available:
http://www.ti.com/tool/OMAP5432-EVM
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
It should be '<<' instead of '<' for _MASK definition, fix it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a DRAM controller driver for the RK3368 and places it in
drivers/ram/rockchip (where the other DM-enabled DRAM controller
drivers for rockchip devices should also be moved eventually).
At this stage, only the following feature-set is supported:
- DDR3
- 32-bit configuration (i.e. fully populated)
- dual-rank (i.e. no auto-detection of ranks)
- DDR3-1600K speed-bin
This driver expects to run from a TPL stage that will later return to
the RK3368 BROM. It communicates with later stages through the
os_reg2 in the pmugrf (i.e. using the same mechanism as Rockchip's DDR
init code).
Unlike other DMC drivers for RK32xx and RK33xx parts, the required
timings are calculated within the driver based on a target frequency
and a DDR3 speed-bin (only the DDR3-1600K speed-bin is support at this
time).
The RK3368 also has the DDRC0_CON0 (DDR ch. 0, control-register 0)
register for controlling the operation of its (single-channel) DRAM
controller in the GRF block. This provides for selecting DDR3, mobile
DDR modes, and control low-power operation.
As part of this change, DDRC0_CON0 is also added to the GRF structure
definition (at offset 0x600).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GMAC in the RK3368 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3368-specific logic necessary to reuse this driver.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To enable the GMAC on the RK3368, we need to set up the clocking
appropriately to generate a tx_clk for the MAC.
This adds an implementation that implements the use of the <&ext_gmac>
clock (i.e. an external 125MHz clock for RGMII provided by the PHY).
This is the clock setup used by the boards currently supported by
U-Boot (i.e. Geekbox, Sheep and RK3368-uQ7).
This includes the change from commit
- rockchip: clk: rk3368: define GMAC_MUX_SEL_EXTCLK
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The original clock support for MMC/SD cards on the RK3368 suffered
from a tendency to select a divider less-or-equal to the the one
giving the requested clock-rate: this can lead to higher-than-expected
(or rather: higher than supported) clock rates for the MMC/SD
communiction.
This change rewrites the MMC/SD clock generation to:
* always generate a clock less-than-or-equal to the requested clock
* support reparenting among the CPLL, GPLL and OSC24M parents to
generate the highest clock that does not exceed the requested rate
In addition to this, the Linux DTS uses HCLK_MMC/HCLK_SDMMC instead of
SCLK_MMC/SCLK_SDMMC: to match this (and to ensure that clock setup
always works), we adjust the driver appropriately.
This includes the changes from:
- rockchip: clk: rk3368: convert MMC_PLL_SEL_* definitions to shifted-value form
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On he RK3368, we need to temporarily disable security on the DMA
engines during TPL and SPL to allow the MMC host to DMA into DRAM. To
do so, we need to reset the two DMA engines, which in turn requires
the DMA1_SRST_REQ and DMA2_SRST_REQ constants to refer to the
appropriate bits in the CRU.
As the ATF correctly initialises security (and only leaves EL3 after
doing so), this can not pose a security issue.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no real reason to keep the bit-definitions for the IOMUX in
the grf header file (which defines the register layout of the GRF block):
these should only be used by our pinctrl driver (with the possible
exception of early debug-init code in TPL/SPL).
This moves the relevant definitions from the grf_rk3368.h header
into the pinctrl driver pinctrl_rk3368.c.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3368 GRF header was still defines with a shifted-mask but with
non-shifted function selectors for the IOMUX defines. As the RK3368
support is still fresh enough to allow a quick change, we do this now
before having more code use this.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
On the RK3368 we use a TPL-stage similar to Rockchip's DDR init
(i.e. it initialises DRAM, leaves some info for the next stage and
returns to the BootROM). To allow compatibility with Rockchip's DDR
init code, we use the same register os_reg2 in pmugrf for passing
this info (i.e. DRAM size and configuration) between stages.
This change adds the definitions for os_reg[0] through os_reg[3] to
the pmugrf structure for the RK3368.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some devices (e.g. the RK3368) have only limited SRAM, but provide
support for loading the next boot stage after our SPL performs basic
setup (e.g. DRAM).
For target systems like these, we add a boot device BOOTROM that will
invoke a board-specific hook to return to the bootrom (if supported).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some new Allwinner SoCs' PRCM has a secure switch register, which
controls the access to some clock and power registers in PRCM block.
Add the definition of this register and its bits in the PRCM header
file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
move to Kconfig:
CONFIG_BCM_SF2_ETH
CONFIG_BCM_SF2_ETH_DEFAULT_PORT
CONFIG_BCM_SF2_ETH_GMAC
Also modified defconfigs of all platforms that use these configs.
Signed-off-by: Suji Velupillai <suji.velupillai@broadcom.com>
Tested-by: Suji Velupillai <suji.velupillai@broadcom.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Modify chip_id() routine such that to handle based on
the current el. Also make it available even if FPGA is
not enabled in system such it can be used always.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch makes chip_id() as a global routine so that
it can be used in other places as required.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch modifies the chip_id routine to get either idcode or
silicon version based on the argument received.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove incorrect code of writing to system timestamp
counter registers. This register writes does nothing
and can be removed.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
TCM on ZynqMP needs to be intialized in a sequence
and this patch provides a global routine to perform
this as per requirement.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The duplicate definitions for IH_ARCH_ARM and IH_ARCH_ARM64 are removed.
The definitions in <image.h> are used.
According to this modification, the comparison between os arch and cpu
arch is done in C programming instead of ASM programming.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Now that EHCD does not use CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>