i.MX6UL: icore: Add SPL_OF_CONTROL support

Add OF_CONTROL support for SPL code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This commit is contained in:
Jagan Teki 2017-11-21 00:02:14 +05:30 committed by Stefano Babic
parent bb0297ccbd
commit 152038ea18
11 changed files with 26 additions and 195 deletions

View file

@ -87,6 +87,7 @@
};
&usdhc1 {
u-boot,dm-spl;
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc1>;
pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
@ -134,6 +135,7 @@
};
pinctrl_usdhc1: usdhc1grp {
u-boot,dm-spl;
fsl,pins = <
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
@ -145,6 +147,7 @@
};
pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
u-boot,dm-spl;
fsl,pins = <
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
@ -156,6 +159,7 @@
};
pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
u-boot,dm-spl;
fsl,pins = <
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9

View file

@ -50,6 +50,7 @@
};
&usdhc2 {
u-boot,dm-spl;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2>;
cd-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
@ -60,6 +61,7 @@
&iomuxc {
pinctrl_usdhc2: usdhc2grp {
u-boot,dm-spl;
fsl,pins = <
MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x17070
MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x10070

View file

@ -82,6 +82,7 @@
};
&usdhc1 {
u-boot,dm-spl;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1>;
cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
@ -128,6 +129,7 @@
};
pinctrl_usdhc1: usdhc1grp {
u-boot,dm-spl;
fsl,pins = <
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059

View file

@ -134,6 +134,7 @@
compatible = "simple-bus";
interrupt-parent = <&gpc>;
ranges;
u-boot,dm-spl;
pmu {
compatible = "arm,cortex-a7-pmu";
@ -185,6 +186,7 @@
#size-cells = <1>;
reg = <0x02000000 0x100000>;
ranges;
u-boot,dm-spl;
spba-bus@02000000 {
compatible = "fsl,spba-bus", "simple-bus";
@ -415,6 +417,7 @@
#interrupt-cells = <2>;
gpio-ranges = <&iomuxc 0 23 10>, <&iomuxc 10 17 6>,
<&iomuxc 16 33 16>;
u-boot,dm-spl;
};
gpio2: gpio@020a0000 {
@ -451,6 +454,7 @@
interrupt-controller;
#interrupt-cells = <2>;
gpio-ranges = <&iomuxc 0 94 17>, <&iomuxc 17 117 12>;
u-boot,dm-spl;
};
gpio5: gpio@020ac000 {
@ -649,6 +653,7 @@
iomuxc: iomuxc@020e0000 {
compatible = "fsl,imx6ul-iomuxc";
reg = <0x020e0000 0x4000>;
u-boot,dm-spl;
};
gpr: iomuxc-gpr@020e4000 {
@ -729,6 +734,7 @@
#size-cells = <1>;
reg = <0x02100000 0x100000>;
ranges;
u-boot,dm-spl;
usbotg1: usb@02184000 {
compatible = "fsl,imx6ul-usb", "fsl,imx27-usb";

View file

@ -316,6 +316,11 @@ config TARGET_MX6UL_GEAM
select DM_MMC
select DM_THERMAL
select SUPPORT_SPL
select SPL_DM if SPL
select SPL_OF_CONTROL if SPL
select SPL_SEPARATE_BSS if SPL
select SPL_PINCTRL if SPL
config TARGET_MX6UL_ISIOT
bool "Support Engicam Is.IoT MX6UL"
select BOARD_LATE_INIT
@ -328,6 +333,10 @@ config TARGET_MX6UL_ISIOT
select DM_MMC
select DM_THERMAL
select SUPPORT_SPL
select SPL_DM if SPL
select SPL_OF_CONTROL if SPL
select SPL_SEPARATE_BSS if SPL
select SPL_PINCTRL if SPL
config TARGET_MX6ULL_14X14_EVK
bool "Support mx6ull_14x14_evk"

View file

@ -7,7 +7,6 @@
*/
#include <common.h>
#include <mmc.h>
#include <asm/io.h>
#include <asm/gpio.h>
@ -89,83 +88,3 @@ void setup_gpmi_nand(void)
setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
}
#endif /* CONFIG_NAND_MXS */
#ifdef CONFIG_SPL_BUILD
/* MMC board initialization is needed till adding DM support in SPL */
#if defined(CONFIG_FSL_ESDHC) && !defined(CONFIG_DM_MMC)
#include <mmc.h>
#include <fsl_esdhc.h>
#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
static iomux_v3_cfg_t const usdhc1_pads[] = {
IOMUX_PADS(PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
/* VSELECT */
IOMUX_PADS(PAD_GPIO1_IO05__USDHC1_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
/* CD */
IOMUX_PADS(PAD_UART1_RTS_B__GPIO1_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* RST_B */
IOMUX_PADS(PAD_GPIO1_IO09__GPIO1_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 1)
struct fsl_esdhc_cfg usdhc_cfg[1] = {
{USDHC1_BASE_ADDR, 0, 4},
};
int board_mmc_getcd(struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
int ret = 0;
switch (cfg->esdhc_base) {
case USDHC1_BASE_ADDR:
ret = !gpio_get_value(USDHC1_CD_GPIO);
break;
}
return ret;
}
int board_mmc_init(bd_t *bis)
{
int i, ret;
/*
* According to the board_mmc_init() the following map is done:
* (U-boot device node) (Physical Port)
* mmc0 USDHC1
*/
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
switch (i) {
case 0:
SETUP_IOMUX_PADS(usdhc1_pads);
gpio_direction_input(USDHC1_CD_GPIO);
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
break;
default:
printf("Warning - USDHC%d controller not supporting\n",
i + 1);
return 0;
}
ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
if (ret) {
printf("Warning: failed to initialize mmc dev %d\n", i);
return ret;
}
}
return 0;
}
#endif /* CONFIG_FSL_ESDHC */
#endif /* CONFIG_SPL_BUILD */

View file

@ -101,106 +101,6 @@ int board_mmc_get_env_dev(int devno)
#ifdef CONFIG_SPL_BUILD
#include <spl.h>
/* MMC board initialization is needed till adding DM support in SPL */
#if defined(CONFIG_FSL_ESDHC) && !defined(CONFIG_DM_MMC)
#include <mmc.h>
#include <fsl_esdhc.h>
#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
static iomux_v3_cfg_t const usdhc1_pads[] = {
IOMUX_PADS(PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
/* VSELECT */
IOMUX_PADS(PAD_GPIO1_IO05__USDHC1_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
/* CD */
IOMUX_PADS(PAD_UART1_RTS_B__GPIO1_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* RST_B */
IOMUX_PADS(PAD_GPIO1_IO09__GPIO1_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
static iomux_v3_cfg_t const usdhc2_pads[] = {
IOMUX_PADS(PAD_NAND_ALE__USDHC2_RESET_B | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
};
#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 19)
#define USDHC2_CD_GPIO IMX_GPIO_NR(4, 5)
struct fsl_esdhc_cfg usdhc_cfg[2] = {
{USDHC1_BASE_ADDR, 0, 4},
{USDHC2_BASE_ADDR, 0, 8},
};
int board_mmc_getcd(struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
int ret = 0;
switch (cfg->esdhc_base) {
case USDHC1_BASE_ADDR:
ret = !gpio_get_value(USDHC1_CD_GPIO);
break;
case USDHC2_BASE_ADDR:
ret = !gpio_get_value(USDHC2_CD_GPIO);
break;
}
return ret;
}
int board_mmc_init(bd_t *bis)
{
int i, ret;
/*
* According to the board_mmc_init() the following map is done:
* (U-boot device node) (Physical Port)
* mmc0 USDHC1
* mmc1 USDHC2
*/
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
switch (i) {
case 0:
SETUP_IOMUX_PADS(usdhc1_pads);
gpio_direction_input(USDHC1_CD_GPIO);
usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
break;
case 1:
SETUP_IOMUX_PADS(usdhc2_pads);
gpio_direction_input(USDHC2_CD_GPIO);
usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
break;
default:
printf("Warning - USDHC%d controller not supporting\n",
i + 1);
return 0;
}
ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
if (ret) {
printf("Warning: failed to initialize mmc dev %d\n", i);
return ret;
}
}
return 0;
}
#ifdef CONFIG_ENV_IS_IN_MMC
void board_boot_order(u32 *spl_boot_list)
{
@ -226,5 +126,4 @@ void board_boot_order(u32 *spl_boot_list)
spl_boot_list[0] = boot_dev;
}
#endif
#endif /* CONFIG_FSL_ESDHC */
#endif /* CONFIG_SPL_BUILD */

View file

@ -40,3 +40,4 @@ CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_MXC_UART=y
CONFIG_IMX_THERMAL=y
CONFIG_SYS_MALLOC_F_LEN=0x2000

View file

@ -38,3 +38,4 @@ CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_MXC_UART=y
CONFIG_IMX_THERMAL=y
CONFIG_SYS_MALLOC_F_LEN=0x2000

View file

@ -40,3 +40,4 @@ CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_MXC_UART=y
CONFIG_IMX_THERMAL=y
CONFIG_SYS_MALLOC_F_LEN=0x2000

View file

@ -215,19 +215,6 @@
# endif
# include "imx6_spl.h"
# ifdef CONFIG_SPL_BUILD
# if defined(CONFIG_IMX6UL)
# if defined(CONFIG_TARGET_MX6UL_ISIOT)
# define CONFIG_SYS_FSL_USDHC_NUM 2
# else
# define CONFIG_SYS_FSL_USDHC_NUM 1
# endif
# define CONFIG_SYS_FSL_ESDHC_ADDR 0
# undef CONFIG_DM_GPIO
# undef CONFIG_DM_MMC
# endif /* CONFIG_IMX6UL */
# endif /* CONFIG_SPL_BUILD */
#endif
#endif /* __IMX6_ENGICAM_CONFIG_H */