Add boot command "bootcmd_ram" to support autoboot from RAM.
This feature could be useful at the very initial state of chip design
when there is only a minimal set of peripheral. (e.g. without mmc and mac ..etc)
The kernel image is default to be loaded at 0x2000000 via debug port,
and the following script serves as an example:
spl()
{
cmd="riscv64-linux-gdb -q \
-ex \"target remote $host:$port\" \
-ex \"load\" \
-ex \"thread apply all set \\\$pc=&_start\" \
-ex \"thread apply all set \\\$a0=\\\$mhartid\" \
-ex \"thread apply all set \\\$a1=<dtb address>\" \
-ex \"restore u-boot.itb binary 0x200000\" \
-ex \"restore Image binary 0x2000000\" \
-ex \"c\" \
spl/u-boot-spl
"
echo $cmd
eval $cmd
}
The address where the kernel is loaded can be altered by
changing the value of KERNEL_IMAGE_ADDR.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Broadcom bnxt L2 driver support. Used by the Broadcom
iproc platforms.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Use the return value ENOSYS for unsupported API
- pinctrl_generic_set_state
- pinctrl_select_state
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM
This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a new function to activate an existing simple frame buffer node
and add the associated reserved memory, with no-map properties.
This device tree update is only done when the video device is active
and the video buffer is used.
This patch uses '#if CONFIG_IS_ENABLED(DM_VIDEO)' because
gd->video_bottom and gd->video_top are only defined when CONFIG_DM_VIDEO
is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the helper function video_is_active() to test if one video device
is active.
This function can be used in board code to execute operation
only when the display is probed / really used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the function named lcd_dt_simplefb* to fdt_simplefb* to be aligned
with the associated file name fdt_simplefb.h/fdt_simplefb.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
This converts the following to Kconfig:
CONFIG_LCD_DT_SIMPLEFB
This patch also renames this config to CONFIG_FDT_SIMPLEFB as the code in
common/lcd_simplefb.c support CONFIG_LCD and CONFIG_VIDEO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Using mmc.dtbo from rpi-firmware to switch the controller for the SD
card slot from sdhci to sdhost causes the numbering to change; the
SD card is then not recognized at boot. Add to the range checked.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The current tpm2_pcr_read is hardcoded using SHA256. Make the
actual command to TPM configurable to use wider range of algorithms.
The current command line is kept as is i.e limited to SHA-256 only.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Platforms may have support to measure their initial firmware components
and pass the event log to u-boot. The event log address can be passed
in property tpm_event_log_addr and tpm_event_log_size of the tpm node.
Platforms may choose their own specific mechanism to do so. A weak
function is added to check if even log has been passed to u-boot
from earlier firmware components. If available, the eventlog is parsed
to check for its correctness and further event logs are appended to the
passed log.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a function that returns the number of devices in a uclass. This can be
helpful in sizing an array that needs to hold a list of them.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it is useful to search just by a partial name, such as
when looking for a sibling device that has a common name substring. Add
helper functions to handle these requirements.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support reading a string list a string at a time. Apart
from being inefficient, this makes it impossible to separate reading of
the devicetree into the of_to_plat() method where it belongs, since any
code which needs access to the string must read it from the devicetree.
Add a function which returns the string property as an array of pointers
to the strings, which is easily used by clients.
Signed-off-by: Simon Glass <sjg@chromium.org>
The details for of_property_read_string_helper() and
ofnode_read_string_index() are a little inaccurate. Fix up the comments to
avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
This method is currently called after the platform data has been freed.
But the pre_unbind() method may wish to access this, e.g. to free some
data structures stored there.
Split the unbinding of devices into two pieces, as is done with removal.
This corrects the problem.
Also tidy a code-style issue in device_remove() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This text should never change during execution, so it makes sense to
use a const char * so that it can be declared as const in the code.
Update struct cmd_tbl with a const char * pointer for 'help'.
We cannot make usage const because of the bmode command, used on mx53ppd
for example.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Adds TEE_ERROR_SHORT_BUFFER as TEE error code. This error code is
commonly used by TEEs to inform caller that the buffer(s) it provided
is too small for the desired operation.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Define identifiers for clnt_login field in struct tee_open_session_arg
based in GlobalPlatform Device TEE IDs and on the REE_KERNEL identifier
extension from OP-TEE OS.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Correct inline comment describing API function devm_scmi_process_msg().
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Certain serial SERDES protocols like 1000base-x, 2500base-x, SGMII,
USXGMII can operate either in a mode where the PHY (be it on-board or
inside an SFP module) passes the link parameters (speed, duplex, pause)
to the MAC through in-band through control words standardized by IEEE
802.3 clause 37, or in a mode where the MAC must configure (force) its
link parameters based on information obtained out-of-band (MDIO reads,
guesswork etc).
In Linux, the OF node property named "managed" is parsed by the phylink
framework, and the convention is that if a driver uses phylink, then the
presence of this property means that in-band autoneg should be enabled,
otherwise it shouldn't.
To be compatible with the OF node bindings of drivers that use phylink
in Linux, introduce parsing support for this property in U-Boot too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In the current DSA switch driver API, only the udevice of the switch
(belonging to UCLASS_DSA) is exposed, as well as an "int port" argument.
So drivers do not have access to the udevice of individual ports
(belonging to UCLASS_ETH), one of the reasons being that not all ports
have an associated UCLASS_ETH udevice.
However, all DSA ports have an OF node, and in some cases the driver
needs a handle to it, for all ports including the CPU port. Example: the
following Linux per-port device tree property:
managed = "in-band-status";
states whether a port should operate with clause 37 in-band autoneg
enabled or not.
This patch exposes a function which can be called by individual drivers
as needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This is needed for the VLAN header structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Freescale TSEC can be a DSA master, and the ports of the attached
DSA switch can have different MAC addresses compared to the TSEC.
Nonetheless, the TSEC must receive the packets on behalf of those switch
ports. Therefore, implement the promiscuous mode method to allow DSA to
set this.
Note that the init_registers() function called from eth_ops :: start
overwrites this setting. There is no reason why the RCTRL register
should be zero-initialized, so just stop clearing it so that the setting
we applied in eth_ops :: set_promisc sticks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We have implemented all what is new in UEFI specification 2.9 and relevant
for U-Boot.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Implement the EFI_EVENT_GROUP_BEFORE_EXIT_BOOT_SERVICES event group
handling.
Add the definition of EFI_EVENT_GROUP_AFTER_READY_TO_BOOT.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This commit adds the comment for efi_system_table and
efi_configuration_table structure.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The extern keyword is not needed in include/lmb.h to declare functions.
Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Correct Sphinx style comments in include/lmb.h
Add the logical memory block API to the HTML documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Defining static functions in includes should be avoided.
Function lmb_is_nomap() is only used in the unit test.
So move it to the unit test.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If bootloader was updated without running oem format, reboot will cause
boot loop because the SYSTEM stage fails.
Add a final PANIC stage running fastboot to permit recovery.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This can lead to GPT and BCB errors even if fastboot was selected early
by usb rom boot and the eMMC is blank/invalid.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
AST2600 leverages the FIT hash/signature verification to fulfill
secure boot trust chain. To improve the performance and save SW
code size for those crypto operations, the two HW crypto engine,
HACE and ACRY, are enabled.
However, both of the engines can only access to data stored in
DRAM space. Therefore, we need to move the FIT image into DRAM
before the booting.
This patch update the CONFIG_BOOTCOMMAND to execute the pre-defined
ENV variable which consists of FIT image copy to memory and booting.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Lot of PCIe controllers are using ECAM addressing. So add common ECAM
macros into U-Boot's pci.h header file which can be suitable for most
PCI controller drivers.
Replace custom ECAM address macros in every PCI controller driver by new
ECAM macros from U-Boot's pci.h header file.
Similar macros are defined also in Linux kernel. There is a small
difference between Linux and these new U-Boot macros.
U-Boot's PCIE_ECAM_OFFSET() takes device and function numbers in separate
arguments. Linux's PCIE_ECAM_OFFSET() takes device and function numbers
encoded in one argument. The reason is that U-Boot's PCI_DEVFN() macro is
different than Linux's PCI_SLOT() macro. So having device and function
numbers in separate arguments makes code more straightforward.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This has different semantics in different places. Go with the bootm method
and put it in a common function so that the behaviour is consistent in
U-Boot. Update the docs.
To be clear, this changes the way that 'bootelf' and standalone boot
work. Before, if autostart was set to "fred" or "YES", for example, they
would consider that a "yes". This may change behaviour for some boards,
but the only in-tree boards which mention autostart use "no" to disable
it, which will still work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Wolfgang Denk <wd@denx.de>
Use a text file for the environment instead of the #define settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
At present U-Boot environment variables, and thus scripts, are defined
by CONFIG_EXTRA_ENV_SETTINGS. It is painful to add large amounts of text
to this file and dealing with quoting and newlines is harder than it
should be. It would be better if we could just type the script into a
text file and have it included by U-Boot.
Add a feature that brings in a .env file associated with the board
config, if present. To use it, create a file in a board/<vendor>
directory, typically called <board>.env and controlled by the
CONFIG_ENV_SOURCE_FILE option.
The environment variables should be of the form "var=value". Values can
extend to multiple lines. See the README under 'Environment Variables:'
for more information and an example.
In many cases environment variables need access to the U-Boot CONFIG
variables to select different options. Enable this so that the environment
scripts can be as useful as the ones currently in the board config files.
This uses the C preprocessor, means that comments can be included in the
environment using /* ... */
Also support += to allow variables to be appended to. This is needed when
using the preprocessor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Marek Behún <marek.behun@nic.cz>
This is a complicated set of #defines and it is painful to convert to a
text file. We can (once pending patches are applied) provide the same
functionality with bootmethod. Drop this for sandbox to allow conversion
to a text-file environment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Compiler is not happy:
common/image-board.c: In function ‘boot_get_kbd’:
common/image-board.c:902:17: warning: implicit declaration of function ‘do_bdinfo’ [-Wimplicit-function-declaration]
902 | do_bdinfo(NULL, 0, 0, NULL);
| ^~~~~~~~~
Move the forward declaration to a header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix dfu_alt_info to use nor1 instead of the device name.
This reverts a part of commit 59bd18d4c4 ("configs: synquacer:
Remove mtdparts settings and update DFU setting") because the
commit a4f2d83414 ("mtd: spi: nor: force mtd name to "nor%d"")
changed the mtd device naming scheme to nor%d.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This symbol has been functionally dead for a long time. Remove the last
and recent re-introductions of setting it, and update the whitelist so
it will not be re-introduced again.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_TRACE
CONFIG_TRACE_BUFFER_SIZE
CONFIG_TRACE_EARLY
CONFIG_TRACE_EARLY_ADDR
CONFIG_TRACE_EARLY_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH
CONFIG_ENV_IS_NOWHERE
CONFIG_ENV_OFFSET
CONFIG_ENV_OVERWRITE
CONFIG_ENV_SECT_SIZE
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Signed-off-by: Tom Rini <trini@konsulko.com>
The last board that used to set CONFIG_LYNXKDI has been removed in
commit 242836a893 ("powerpc: ppc4xx: remove pcs440ep support"),
doc/README.lynxkdi only talks about a MPC8260 board being supported,
and the mpc8260 support has been removed four years ago in commit
2eb48ff7a2 ("powerpc, 8260: remove support for mpc8260") already,
and common/lynxkdi.c only consists of an "#error" statement these
days, so it seems like the LYNX KDI code is dead code nowadays.
Let's remove it now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Refactor this code so that we can call the 'pxe get' command without going
through the command-line interpreter. This makes it easier to get the
information we need, without going through environment variables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
It is pretty strange that the pxe code uses the 'filesize' environment
variable find the size of a file it has just read.
Partly this is because it uses the command-line interpreter to parse its
request to load the file.
As a first step towards unwinding this, return it directly from the
getfile() function. This makes the code a bit longer, for now, but will be
cleaned up in future patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add an xtoa() function, similar to itoa() but for hex instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
This function no longer makes sense, since it is pretty easy to prepend
the boot directory to the filename. Drop it and update its only caller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The 'bootfile' environment variable is read in the bowels of pxe_util to
provide a directory to which all loaded files are relative.
This is not obvious from the API to PXE and it is strange to make the
caller set an environment variable rather than pass this as a parameter.
The code is also convoluted, which this feature implemented by
get_bootfile_path().
Update the API to improve this. Unfortunately this means that
pxe_setup_ctx() can fail, so add error checking.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Both the syslinux and pxe commands use essentially the same code to parse
and run extlinux.conf files. Move this into a common function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Move the header file into the main include/ directory so we can use it
from the bootmethod code. Move the C file into boot/ since it relates to
booting.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
There's a lot of code duplication in U-Boot right now. All the TPM TIS
compatible drivers we have at the moment have their own copy of a TIS
implementation.
So let's create a common layer which implements the core TIS functions.
Any driver added from now own, which is compatible with the TIS spec, will
only have to provide the underlying bus communication mechanisms.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
In some part of STM32MP15 support the CONFIG_TFABOOT can be replaced
by other config: CONFIG_ARMV7_PSCI and CONFIG_ARM_SMCCC.
This patch also simplifies the code in cpu.c, stm32mp1_ram.c and
clk_stml32mp1.c as execution of U-Boot in sysram (boot without SPL and
without TFA) is not supported: the associated initialization code is
present only in SPL.
This cleanup patch is a preliminary step to support SPL load of OP-TEE
in secure world, with SPL in secure world and U-Boot in no-secure world.
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add a configuration file "stm32mp15_st_common.h" to handle the
STMicroelectronics boards configuration and rename stm32mp1.h to
"stm32mp15_common.h" to handle the generic STM32MP15x series configuration.
The configuration file "dh_stm32mp1.h" is also renamed to
"stm32mp15_dh_dhcom" for the configuration of board based on the
dhelectronics STM32MP15x SOM.
In the STMicroelectronics board configuration the default bootcmd
"bootcmd_stm32mp" is updated to only select the extlinux file found on
SD-Card on STM32MP15x EV1 for boot from NOR device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LS1046A-QDS has CONFIG_SPI_FLASH_SST, CONFIG_SPI_FLASH_EON and
CONFIG_SPI_FLASH_STMICRO defines present in header. Move these entries
from header to defconfigs.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a helper to iterate over all nodes with a given compatible string.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that everything is prepared, copy the fsl-ls1028a.dtsi from the
linux kernel v5.14.12.
Notable changes:
- second watchdog added
- the number of chip selects of the SPI controller is now correct and
reflects what the hardware offers
- the LPUARTs have the correct clock parent
- USB controllers are enabled by default, which was already the case
before this sync because all board enabled all the USB controller
nodes. A linux patch to fix this is pending.
- the eSDHC controller changes from big-endian to little-endian, but
that property seems to be not used at all.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable support for update over EFI UpdateCapsule mechanism. This board
doesn't support setting EFI variables after ExitBootservices().
Therefore, we are also enabling EFI_IGNORE_OSINDICATIONS.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add a function to return this information along with a stub for the
efi_info_get() function, since calling it otherwise hangs U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This commit adds the EFI_TCG2_PROTOCOL.SubmitCommand
required in the TCG PC Client PFP spec.
SubmitCommand enables to send the raw command to the TPM device.
To implement this api, tpm2_submit_command() is added
into tpm-v2.c.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F
CONFIG_BOARD_LATE_INIT
CONFIG_DISPLAY_BOARDINFO
CONFIG_DISPLAY_BOARDINFO_LATE
Signed-off-by: Tom Rini <trini@konsulko.com>
Add an option to automatically register watchdog devices with the
wdt_reboot driver for use with sysreset. This allows sysreset to be a
drop-in replacement for platform-specific watchdog reset code, without
needing any device tree changes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Allow usage of the bootstage facilities in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Check sizeof(default_environment) against ENV_SIZE in a static_assert()
instead of runtime.
Only check if !USE_HOSTCC (for in fw_env tool ENV_SIZE expands to a
variable, and cannot be checked statically) nad
!DEFAULT_ENV_INSTANCE_EMBEDDED, for in that case the default_environment
variable is not set.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sometimes we use uchar and sometimes char for the default environment
array. By always using char, we can get rid of some explicit casts.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
The data blob apparently does not need to be modified through the fit
field of the image_sign_info struct so make it point to const to avoid
the need to cast away constness in functions that assign a pointer to
const data to the field.
fit_image_setup_verify already had to cast away constness as it assigned
a const void * argument to the field. The cast can now be removed.
Signed-off-by: Hannu Lounento <hannu.lounento@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Samsung S9 SM-G9600 - Snapdragon SDM845 version of the phone,
for China \ Hong Kong markets.
Has unlockable bootloader, unlike SM-G960U (American market version),
which allows running u-boot as a chain-loaded bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Hi-end qualcomm chip, introduced in late 2017.
Mostly used in flagship phones and tablets of 2018.
Features:
- arm64 arch
- total of 8 Kryo 385 Gold / Silver cores
- Hexagon 685 DSP
- Adreno 630 GPU
Tested only as second-stage bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Add preliminary device trees for the Apple M1 mini (2020) and
Apple M1 Macbook Pro 13" (2020). Device tree bindings for
the Apple M1 SoC are still being formalized and these device
trees will be synchronized with the Linux kernel as needed.
The device trees in this commit are based on the initial Apple
M1 device trees from Linux 5.13, nodes for dart, pcie, pinctrl,
pmgr, usb based on bindings on track for inclusion in Linux
5.15 and 5.16 and nodes for i2c, mailbox, nvme, pmu, spmi and
watchdog that don't have a proposed binding yet.
These device trees are provided as a reference only as U-Boot
uses the device tree passed by the m1n1 bootloader.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Apple's M1 SoC that is used in "Apple Silicon"
Macs. This builds a basic U-Boot that can be used as a payload
for the m1n1 boot loader being developed by the Asahi Linux
project.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add MAINTAINERS entry]
This uclass is intended to manage IOMMUs on systems where the
IOMMUs are not in bypass mode by default. In that case U-Boot
cannot ignore the IOMMUs if it wants to use devices that need
to do DMA and sit behind such an IOMMU.
This initial IOMMU uclass implementation does not implement and
device ops and is intended for IOMMUs that have a bypass mode
that does not require address translation. Support for IOMMUs
that do require address translation is planned and device ops
will be defined when support for such IOMMUs will be added.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds an implementation of the wait_dat0 MMC operation for the DM SDHCI
driver, allowing the driver to continue when the card is ready rather
than waiting for the worst case time on each MMC switch operation.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
OF_HOSTFILE is used on sandbox configs only. Although it's pretty
unique and not causing any confusions, we are better of having simpler
config options for the DTB.
So let's replace that with the existing OF_BOARD. U-Boot would then
have only three config options for the DTB origin.
- OF_SEPARATE, build separately from U-Boot
- OF_BOARD, board specific way of providing the DTB
- OF_EMBED embedded in the u-boot binary(should not be used in production
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds the UEFI GPT disk partition topology
measurement required in TCG PC Client Platform Firmware
Profile Specification
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
First two fields are reversed compared to what is expected by the SCMI
specification.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Fixes: 6038884483 ("clk: add clock driver for SCMI agents")
TCG PC Client Platform Firmware Profile Specification
requires to measure the SMBIOS table that contains static
configuration information (e.g. Platform Manufacturer
Enterprise Number assigned by IANA, platform model number,
Vendor and Device IDs for each SMBIOS table).
The device- and environment-dependent information such as
serial number is cleared to zero or space character for
the measurement.
Existing smbios_string() function returns pointer to the string
with const qualifier, but exisintg use case is updating version
string and const qualifier must be removed.
This commit removes const qualifier from smbios_string()
return value and reuses to clear the strings for the measurement.
This commit also fixes the following compiler warning:
lib/smbios-parser.c:59:39: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
const struct smbios_header *header = (struct smbios_header *)entry->struct_table_address;
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Make sure to (if applicable) flush the D-cache, invalidate I-cache,
and disable MMU and caches before jumping to OPTEE.
This fixes the SDP->SPL->OPTEE boot flow on iMX6Q and most likely on
some other ARM SoCs.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
In multiple places we need the default GUID matching a variable name.
The patch provides a library function. For secure boot related variables
like 'PK', 'KEK', 'db' a lookup table is used. For all other variable
names EFI_GLOBAL_VARIABLE is returned.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
UEFI variable names are typically constants and hence should be defined as
const. Unfortunately some of our API functions do not define the parameters
for UEFI variable names as const. This requires unnecessary conversions.
Adjust parameters of several internal functions to tre UEFI variable names
as const.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit fixes the following compilation warning
of boottime->install_configuration_table() function.
lib/efi_selftest/efi_selftest_tcg2.c:475:46:
warning: passing argument 1 of ‘boottime->install_configuration_table’
discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
ret = boottime->install_configuration_table(&smbios_guid, dmi);
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
- Add and enable watchdog driver
- Prepare for SYSRESET driven AXP poweroff
- Prepare for SoCs without MMC2
- Some fixes for extending SPL (SPL-DM for RISC-V)
- Some preparations for proper VBUS management
- Fix secure monitor move
A single DM-based driver should be able to support some feature for
several PMIC variants where the interface is the same. For example,
all PMIC variants use the same register bit to trigger poweroff.
However, currently only definitions for a single PMIC are available at
a time. This requires drivers to use #ifdefs and different indentifiers
for each variant they support.
Let's simplify this by making register definitions for all variants
available from the header. Then no preprocessor conditions are needed;
the driver can use the register definition from any variant that
supports the relevant feature.
An exception is the GPIO-related definitions, which do not use unique
identifiers. So for now, keep them like before. They will be cleaned up
along with the GPIO driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This header attempted to avoid multiple inclusion using a header guard.
But the preprocessor symbol was never defined, so the guard had no
effect. Fix this by defining the symbol.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
commit 1ebfc0c631 ("sunxi: A23/A33/H3: Move sun8i secure monitor to
SRAM A2") attempted to move the secure monitor to SRAM A2. But not all
sun8i SoCs have SRAM A2, so a check was put in for SUNXI_SRAM_A2_SIZE to
avoid breaking the other SoCs.
However, because the header providing SUNXI_SRAM_A2_SIZE was not
included, this unintentionally skipped the new definitions on all SoCs.
Fix this by including the right header.
Fixes: 1ebfc0c631 ("sunxi: A23/A33/H3: Move sun8i secure monitor to SRAM A2")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The original purpose of mtd_erase_callback() in Linux at the time it was
imported to U-Boot, was to inform the caller that erasing is done (since
it was an asynchronous operation).
All supplied callback methods in U-Boot do nothing, but the
mtd_erase_callback() function was (until previous patch) grossly abused
in U-Boot's mtdpart implementation for completely different purpose.
Since we got rid of the abusement, remove the mtd_erase_callback()
function and the .callback member from struct erase_info entirely, in
order to avoid such problems in the future.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Check for zero length in the legacy spi_flash_read() /
spi_flash_write() / spi_flash_erase() functions.
On zero length, return 0 immediately, don't call the underlying method.
Rationale:
- these legacy functions call the _read(), _write() and _erase() methods
of struct mtd
- the DM callers of these methods already check for zero length
- making all callers of these methods check for zero length makes it
possible to remove the check from implementations of these _read(),
_write() and _erase() methods
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Currently the env_get_f() function's return value behaves weirdly: it
returns the number of bytes written into `buf`, but whether this is
excluding the terminating NULL-byte or including it depends on whether
there was enough space in `buf`.
Change the function to always return the actual length of the value of
the environment variable (excluding the terminating NULL-byte) on
success. This makes it behave like sprintf().
All users of this function in U-Boot are compatible with this change.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function is a relic from the past when environment was read from
underlying device one character at a time.
It is used only in the case when getting an environemnt variable prior
relocation, and the function is simple enough to be inlined there.
Since env_get_char() is being changed to simple access to an array, we
can drop the failing cases and simplify the code (this could have been
done before, since env_get_char() did not fail even before).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function was used by other parts of U-Boot in the past when
environment was read from underlying device one character at a time.
This is not the case anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function actually returns:
- the number of bytes written into @buf excluding the terminating
NULL-byte, if there was enough space in @buf
- the number of bytes written into @buf including the terminating
NULL-byte, if there wasn't enough space in @buf
- -1 if the variable is not found
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix up the header's include guard to contain the definition of
dm_priv_to_rw(), which was erroneously added outside of it, by moving
its #endif to the end of the file (i.e. where it belongs). This removes
the risk of compilation errors resulting from the redefinition of that
function where the header might have been (indirectly) included more
than once.
Fixes: cfb9c9b77c ("dm: core: Use separate priv/plat data region")
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
Cc: Simon Glass <sjg@chromium.org>
Instead of declaring CONFIG_SPL_DRIVERS_MISC in board config header,
select it in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Instead of declaring CONFIG_SYS_MALLOC_SIMPLE dependant on
CONFIG_SPL_BUILD in board config header, select
CONFIG_SPL_SYS_MALLOC_SIMPLE in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reorder the definitions in Turris MOX' board config header, drop the
comment relics from when this file was copied, fix indentation.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move the config option CONFIG_I2C_MV to a Kconfig option
CONFIG_SYS_I2C_MV and move the default definition from config header
files into defconfigs.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move config options CONFIG_LAST_STAGE_INIT and
CONFIG_DISPLAY_BOARDINFO_LATE to turris_mox_defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Create the GUID as a global variable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Parameter size is never used in function efi_dp_from_lo(). Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Instead of copying a GUID and then using a pointer to the copy for calling
guidcmp(), just pass the pointer to the orginal GUID.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We are ignoring the alignment communicated via the PE/COFF header.
Starting 5.10 the Linux kernel will loudly complain about it. For more
details look at [1] (in linux kernel).
So add a function that can allocate aligned EFI memory and use it for our
relocated loaded image.
[1] c32ac11da3f83 ("efi/libstub: arm64: Double check image alignment at entry")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Vincent Stehlé <vincent.stehle@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Complete the Sphinx documentation in include/sysreset.h
Add the include to the generated HTML documentation of the U-Boot API.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add code to build the eMMC variant of the Colibri iMX6ULL, i.e. the
'Colibri iMX6ULL 1GB' which has a eMMC instead of the raw NAND used
on other SKUs.
Related-to: ELB-4056, ELB-4057
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Integrate new Toradex SKU 0062 Colibri iMX6ULL 1GB IT. This commit
basically adjusts three parameters of the RAM settings:
Increase density from 4Gb to 8Gb
Increase ROW address from 15 to 16
Increase tRFC (refresh command time) from 260 to 350
This timing is valid for all Toradex Colibri iMX6ULL SKUs
Related-to: ELB-4055, ELB-4057
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Variable "kernel_image" is used in boot.scr script only, that sets its
own default value to the constant string @@KERNEL_IMAGETYPE@@ in case
"kernel_image" is not set.
The default name of the kernel image shipped with BSP 5.x is "Image.gz".
Setting kernel_image="Image" as a pre-defined u-boot variable
breaks booting systems with modern versions of boot.scr, whereas
renaming it fixes booting with modern scripts and does not break working
of earlier versions of boot.scr.
While at it also update the copyright period, rather than hard-coding
fdtfile default fdt_board to dev for the Verdin iMX8M Mini and fix its
closing #endif comment.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Even if board can be successfuly built, CI goes in deadlock (see thread
on https://www.mail-archive.com/u-boot@lists.denx.de/msg419663.html).
This is caused by SYS_CONFIG set in header file and because defconfig
for the board is out of sync with Kconfig. As result, buildman goes on
to read from stdin until an OOM is reached.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Frieder Schrempf <frieder.schrempf@kontron.de>
Like dev_read_addr_ptr(), provide a wrapper for the indexed version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present there is only devfdt_get_addr_ptr() which only returns
the first <addr, size> pair in the 'reg' property. Add a new API
devfdt_get_addr_index_ptr() to return the indexed pointer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bulletproof the default boot command with reset statements in case
any command in the chain would fail. In case a failure were to happen,
the board will reset, increment boot counter and retry the procedure.
In case the failures persist and the boot counter reaches the bootlimit,
U-Boot starts altbootcmd instead of the default bootcmd boot command.
The altbootcmd swaps the default boot partition for the other boot
partition, which is an identical copy or an older copy, and tries
booting from that one instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Move setting CONFIG_BOOTCOMMAND to the mx7ulp_com_defconfig file.
It also allows replacing the default CONFIG_BOOTCOMMAND without
code modification.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The previous patches removed OF_PRIOR_STAGE from the last consumers of the
Kconfig option. Cleanup any references to it in documentation, code and
configuration options.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
On mvebu this is defined if and only if !ARM64.
Otherwise it is defined for boards with ARCH_MX23, ARCH_TEGRA and
ARCH_ZYNQ, and also for SOC_AR934X (tplink_wdr4300).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This option is only used for
mx23evk_defconfig
mx23_olinuxino_defconfig
which are the only i.MX23 boards.
Add depend on ARCH_MX23 and default to y.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
In preparation for moving this option to Kconfig, rename it to be
consistent with other USB EHCI Kconfig options.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Remove the latest reference of CONFIG_CONS_NONE in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the latest reference of CONFIG_SYS_FLASH_AMD_CHECK_DQ7 in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the latest reference of CONFIG_NO_RELOCATION in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This define was left over from a previous revision, and was never used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove some config finishing by _ badly added by
scripts/build-whitelist.sh when joker is used in comments.
for example:
doc/uImage.FIT/command_syntax_extensions.txt:
... #ifdef CONFIG_OF_* | ...
cmd/nvedit.c:# error Define one of CONFIG_ENV_IS_IN_{EEPROM| \
FLASH|MMC|FAT|EXT4|\
Remove also configs only used in comments:
- CONFIG_BOOGER in include/linux/kconfig.h
- CONFIG_COMMANDS
- CONFIG_INIT_IGNORE_ERROR
- CONFIG_REG_*
- CONFIG_HOTPLUG : drivers/watchdog/omap_wdt.c:18
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The EMC frequency tables are created from a training sequence performed
during early boot and passed in via a reserved memory region by nvtboot.
Copy this table to the kernel DTB so that the kernel can use it to scale
the EMC frequency at runtime.
Note that early bootloaders store the EMC table at an address that
currently intersects with the load address of the initial ramdisk. In
order to avoid copying the table to a different address, simply change
the load address for the initial ramdisk in U-Boot.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reserved memory nodes can have additional flags. Support reading and
writing these flags to ensure that reserved memory nodes can be properly
parsed and emitted.
This converts support for the existing "no-map" flag to avoid extending
the argument list for fdtdec_add_reserved_memory() to excessive length.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The fdtdec_set_carveout() function's parameters are inconsistent with
the parameters passed to fdtdec_add_reserved_memory(). Fix up the order
to make it more consistent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reserved memory nodes can have a compatible string list to identify the
type of reserved memory that they represent. Support specifying an
optional compatible string list when creating these nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When retrieving a given carveout for a device, allow callers to query
the name. This helps differentiating between carveouts when there are
more than one.
This is also useful when copying carveouts to help assign a meaningful
name that cannot always be guessed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
Fix a regression brings by commit 84f8e36f03 ("cmd: bind: allow to
bind driver with driver data")
As example, the following bind command doesn't work:
bind /soc/usb-otg@49000000 usb_ether
As usb_ether driver has no compatible string, it can't be find by
lists_bind_fdt(). In bind_by_node_path(), which called lists_bind_fdt(),
the driver entry is known, pass it to lists_bind_fdt() to force the driver
entry selection.
For this, add a new parameter struct *driver to lists_bind_fdt().
Fix also all lists_bind_fdt() callers.
Fixes: 84f8e36f03 ("cmd: bind: allow to bind driver with driver data")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).
Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.
This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the rsb functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants, so move that to the common header.
There are only a couple of pairs of hardware/runtime addresses used
across all PMIC variants. So far the code expected only the "primary"
pair, but some PMICs like the AXP305 and AXP805 use the secondary pair,
so add support for that to the DM driver as well.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the p2wi functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants. Move that to the common header, so it can be used by
both interface implementations.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Account for the changes done between merge proposal and the final merge.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The CCU header is only used by the DM drivers, not any platform code.
Its current location adds an artificial dependency on CONFIG_ARM and
ARCH_SUNXI, which will be problematic when adding the CCU driver for
a RISC-V sunxi platform.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Move CONFIG_VIDEO_MXS from board headers to Kconfig
and drop it from obsolete cfb_console driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
At present U-Boot has a header file called lz4.h for its own use. If the
host has its own lz4 header file installed (e.g. from the 'liblz4-dev'
package) then host builds will use that instead.
Move the U-Boot file into its own directory, as is done with various
other headers with the same problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for 30bpp mode where pixels are picked in 32-bit
integers but use 10 bits instead of 8 bits for each component.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
This file has a lot of conditional code and much of it is unnecessary.
Clean this up to reduce the number of build combinations.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is only used in one place and does not need to use the
preprocessor. Move it to the C file and convert it to a normal function.
Drop fit_unsupported() since it is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
We can use the new host_build() function for this, so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough and the board code is now in a separate file. Update the only place
where this is used and drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for FIT_RSASSA_PSS. With this we can use
CONFIG_IS_ENABLED(FIT_RSASSA_PSS) directly in the host build, so drop the
forcing of this in the image.h header.
Drop the #ifdef around padding_pss_verify() too since it is not needed.
Use the compiler to check the config where possible, instead of the
preprocessor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for FIT_VERBOSE. With this we can use
CONFIG_IS_ENABLED(FIT_VERBOSE) directly in the tools build, so drop the
forcing of this in the image.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for OF_LIBFDT. With this we can use
CONFIG_IS_ENABLED(OF_LIBFDT) directly in the tools build, so drop the
unnecessary indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Make use of the host Kconfig for FIT. With this we can use
CONFIG_IS_ENABLED(FIT) directly in the host build, so drop the unnecessary
indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
At present when building host tools, we force CONFIG_SHAxxx to be enabled
regardless of the board Kconfig setting. This is done in the image.h
header file.
For SPL we currently just assume the algorithm is desired if U-Boot proper
enables it.
Clean this up by adding new Kconfig options to enable hashing on the host,
relying on CONFIG_IS_ENABLED() to deal with the different builds.
Add new SPL Kconfigs for hardware-accelerated hashing, to maintain the
current settings.
This allows us to drop the image.h code and the I_WANT_MD5 hack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
At present we must separately test for the host build for many options,
since we force them to be enabled. For example, CONFIG_FIT is always
enabled in the host tools, even if CONFIG_FIT is not enabled by the
board itself.
It would be more convenient if we could use, for example,
CONFIG_IS_ENABLED(FIT) and get CONFIG_HOST_FIT, when building for the
host. Add support for this.
With this and the tools_build() function, we should be able to remove all
the #ifdefs currently needed in code that is build by tools and targets.
This will be even nicer when we move to using CONFIG(xxx) everywhere,
since all the #ifdef and IS_ENABLED/CONFIG_IS_ENABLED stuff will go away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> # b4f73886
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
With the new TOOLS_LIBCRYPTO and some other changes, it seems that we are
heading towards calling this a tools build rather than a host build,
although of course it does happen on the host.
I cannot think of anything built by the host which cannot be described as
a tool, so rename this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a macro to handle manually relocating a pointer. Update the iamge code
to use this to avoid needing #ifdefs.
This also fixes a bug where the 'done' flag was not set.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than adding an #ifdef and open-coding this calculation, add a
helper function to handle it. Use this in the image code.
Signed-off-by: Simon Glass <sjg@chromium.org>
The gzip API uses the u64 type in it, which is not available in the host
build. This makes it impossible to include the header file.
We could make this type available, but it seems unnecessary. Limiting the
compression size to that of the 'unsigned long' type seems good enough. On
32-bit machines the limit then becomes 4GB, which likely exceeds available
RAM anyway, therefore it should be sufficient. On 64-bit machines this is
effectively u64 anyway.
Update the header file and implementation to use 'ulong' instead of 'u64'.
Add a definition of u32 for the cases that seem to need exactly that
length. This should be safe enough.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing zstd API requires the same sequence of calls to perform its
task. Create a helper for U-Boot, to avoid code duplication, as is done
with other compression algorithms. Make use of of this from the image
code.
Note that the zstd code lacks a test in test/compression.c and this should
be added by the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
When passing a data buffer back from a function, it is not always clear
who owns the buffer, i.e. who is responsible for freeing the memory used.
An example of this is where multiple files are decompressed from the
firmware image, using a temporary buffer for reading (since the
compressed data has to live somewhere) and producing a temporary or
permanent buffer with the resuilts.
Where the firmware image can be memory-mapped, as on x86, the compressed
data does not need to be buffered, but the complexity of having a buffer
which is either allocated or not, makes the code hard to understand.
Introduce a new 'abuf' which supports simple buffer operations:
- encapsulating a buffer and its size
- either allocated with malloc() or not
- able to be reliably freed if necessary
- able to be converted to an allocated buffer if needed
This simple API makes it easier to deal with allocated and memory-mapped
buffers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that PCI Bridge (PCIe Root Port) for Aardvark is emulated in U-Boot,
add support for handling and propagation of CRSSVE bit.
When CRSSVE bit is unset (default), driver has to reissue config
read/write request on CRS response.
CRSSVE bit is supported only when CRSVIS bit is provided in read-only
Root Capabilities register. So manually inject this CRSVIS bit into read
response for that register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Remove the latest reference of CONFIG_USER_LOWLEVEL_INIT in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move CONFIG_BOOTCOMMAND defined in Kconfig in the board defconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Using the tools moveconfig.py to move the following config in the
defconfig files:
CONFIG_USB_HOST_ETHER
CONFIG_USB_ETHER_ASIX
CONFIG_USB_ETHER_MCS7830
CONFIG_USB_ETHER_SMSC95XX
These option are already migrated since the commit f58ad98a62 ("usb: net:
migrate USB Ethernet adapters to Kconfig") and the commit ae3584498b
("usb: net: migrate CONFIG_USB_HOST_ETHER to Kconfig").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the CONFIG_STM32_FLASH to Kconfig by using
tools/moveconfig.py
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This reverts commit d5d726d3cc,
which breaks boards which ship with multiple SD/eMMC sockets.
This stm32mp1.h config is not used only by the ST reference
boards, but all the other STM32MP1 based boards in U-Boot, so
changes to this stm32mp1.h cannot break the other boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
These platforms never had to support an ATAGs-based Linux Kernel, so
remove the options.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Import HS400 support for iMX7ULP B0 from the Linux kernel:
2eaf5a533afd ("mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP")
According to IC suggest, need to clear the STROBE_DLL_CTRL_RESET
before any setting of STROBE_DLL_CTRL register.
USDHC has register bits(bit[27~20] of register STROBE_DLL_CTRL)
for slave sel value. If this register bits value is 0, it needs
256 ref_clk cycles to update slave sel value. IC suggest to set
bit[27~20] to 0x4, it only need 4 ref_clk cycle to update slave
sel value. This will short the lock time of slave.
i.MX7ULP B0 will need more time to lock the REF and SLV, so change
to add 5us delay.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
When using SWUpdate, it is necessary to toggle between partitions.
Use the 'mmcpart' environment variable to accomplish that.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The CONFIG_SPL_MAX_SIZE definition did not account for all areas that
are used by the boot ROM according to the manual, causing boot failures
due to truncated SPL images when actually hitting this limit.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
The BSP platform LmP supports the board NXP iMX8QM MEK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
The BSP platform LmP supports the board NXP iMX8M Plus EVK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
The BSP platform LmP supports the board NXP iMX8M Mini EVK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
add hook function spl_load_simple_fit_fix_load()
which is called after fit image header is loaded.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
JetHub devices uses its own boot sequence with "rescue" button
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SCSI device can be a PCIe adapter, so run pcie enum if enabled.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SCSI target to be able to boot from the SATA disks on the Odroid HC4 using
an on-board AHCI PCIe controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Import Amlogic DT changes from Linux commit 7d2a07b76933 ("Linux 5.14"),
dt-bindings clock changes and new meson-g12b-gsking-x.dts,
meson-sm1-bananapi-m5 & odroid-hc4 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Typically platforms will define CONFIG_SYS_NAND_PAGE_COUNT based on
CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE. Switch to this
in preparation for migrating CONFIG_SYS_NAND namespace to Kconfig.
Cc: Marek Vasut <marex@denx.de>
Cc: Olaf Mandel <o.mandel@menlosystems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These platforms do not currently enable NAND, remove these references.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The generic GPIO flags binding is shared across many drivers, some of
which need their own xlate function. Factor out the flag translation
code from gpio_xlate_offs_flags so it does not need to be duplicated.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This value is not used by u-boot, and it should not. The load address
of an OPTEE image is defined by said image. Either a uImage or a FIT
will have a defined load address and entry point. Those values are the
correct ones, not CONFIG_OPTEE_LOAD_ADDR.
Commit f25006b96e ("optee: Add CONFIG_OPTEE_LOAD_ADDR") justifies
this config by requiring its presence in u-boot's .config for other
images as part of a larger build, claiming it is "the best way".
This argument is not persuasive. U-boot's configuration is driven by
platform requirements, not the other way around. It seems more likely
that the argument is conflating tooling issues with Kconfig. Yocto and
buildroot have excellent mechanisms for defining values across the
board (pun intended). u-boot's Kconfig is the wrong place to do it.
Furthermore, it is not "best" for u-boot because it hardcodes a value
which is then not used. In fact the load address that u-boot uses is
the one derived from the OPTEE image.
Confused yet? I sure was. To prevent future confusion, remove
CONFIG_OPTEE_LOAD_ADDR.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The configs TZDRAM_BASE and TZDRAM_SIZE are expected to describe the
memory allocated to the OPTEE region. according to according to commit
c5a6e8bd00 ("optee: Add optee_verify_bootm_image()"). The TZDRAM is
with some limitations, described by "/reserved-memory" nodes in the
devicetree.
Consequently TZDRAM_BASE and TZDRAM_SIZE can point to imaginary
regions which have nothing to do with actual DRAM. They are not used
to configure the hardware or set up the Trust Zone Controller (TZC)
for OP-TEE -- the devicetree values are used instead.
When a valid OP-TEE image does not fall within the region described by
these configs, u-boot will refuse to load it. In fact, it mostly
serves to cause "bootm" to reject perfectly good OP-TEE images.
Ironically, someone has to correctly configure the devicetree for
TZDRAM, then go back and enter the same information in Kconfig for
"bootm". To remedy this, do not use TZDRAM_BASE and TZDRAM_SIZE in the
verification of OPTEE images.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add stub for tee_find_device function when CONFIG_TEE is not activated
to simplify the caller code.
This patch allows to remove the CONFIG_IS_ENABLED(OPTEE) tests
for stm32 platform.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Etienne Carriere <etienne.carriere@inaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
The configuration CONFIG_OPTEE is defined 2 times:
1- in lib/optee/Kconfig for support of OPTEE images loaded by bootm command
2- in drivers/tee/optee/Kconfig for support of OP-TEE driver.
It is abnormal to have the same CONFIG define for 2 purpose;
and it is difficult to managed correctly their dependencies.
Moreover CONFIG_SPL_OPTEE is defined in common/spl/Kconfig
to manage OPTEE image load in SPL.
This definition causes an issue with the macro CONFIG_IS_ENABLED(OPTEE)
to test the availability of the OP-TEE driver.
This patch cleans the configuration dependency with:
- CONFIG_OPTEE_IMAGE (renamed) => support of OP-TEE image in U-Boot
- CONFIG_SPL_OPTEE_IMAGE (renamed) => support of OP-TEE image in SPL
- CONFIG_OPTEE (same) => support of OP-TEE driver in U-Boot
- CONFIG_OPTEE_LIB (new) => support of OP-TEE library
After this patch, the macro have the correct behavior:
- CONFIG_IS_ENABLED(OPTEE_IMAGE) => Load of OP-TEE image is supported
- CONFIG_IS_ENABLED(OPTEE) => OP-TEE driver is supported
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This adds support for the IOT2050 Basic and Advanced devices. The Basic
used the dual-core AM6528 GP processor, the Advanced one the AM6548 HS
quad-core version.
Both variants are booted via a Siemens-provided FSBL that runs on the R5
cores. Consequently, U-Boot support is targeting the A53 cores. U-Boot
SPL, ATF and TEE have to reside in SPI flash.
Full integration into a bootable image can be found on
https://github.com/siemens/meta-iot2050
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The weak definition of pci_skip_dev from drivers/pci/pci_common.c is not
under CONFIG_DM_PCI_COMPAT, and that definition needs a previous
function prototype declaration to avoid W=1 build warnings.
That prototype is not available due to it being under CONFIG_DM_PCI_COMPAT,
so move it outside of that preprocessor block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This resyncs the dts files for all of the currently in-tree K3
platforms, along with relevant bindings, with the v5.14 Linux Kernel
release. Of note are that the main-navss/mcu-navss nodes were renamed
to main_navss / mcu_navss and so the u-boot.dtsi files needed to be
updated to match.
Tested on j721e_evm and am65x_evm.
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of platforms are still defining CONFIG_SYS_BAUDRATE_TABLE to
the fallback default of "{ 9600, 19200, 38400, 57600, 115200 }", but
with varying whitespace, or were introduced after the default fallback
was added. Use the default table here.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last armada100 platform, remove that support
as well.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
=aQtT
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.01-rc1
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
nand_dt_init() is still using fdtdec_xx() interface.
If OF_LIVE flag is enabled, dt property can't be get anymore.
Updating all fdtdec_xx() interface to ofnode_xx() to solve this issue.
For doing this, node parameter type must be ofnode.
First idea was to convert "node" parameter to ofnode type inside
nand_dt_init() using offset_to_ofnode(node). But offset_to_ofnode()
is not bijective, in case OF_LIVE flag is enabled, it performs an assert().
So, this leads to update nand_chip struct flash_node field from int to
ofnode and to update all nand_dt_init() callers.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Force the mtd name of spi-nor to "nor" + the driver sequence number:
"nor0", "nor1"... beginning after the existing nor devices.
This patch is coherent with existing "nand" and "spi-nand"
mtd device names.
When CFI MTD NOR device are supported, the spi-nor index is chosen after
the last CFI device defined by CONFIG_SYS_MAX_FLASH_BANKS.
When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated, this config
is replaced by to cfi_flash_num_flash_banks in the include file
mtd/cfi_flash.h.
This generic name "nor%d" can be use to identify the mtd spi-nor device
without knowing the real device name or the DT path of the device,
used with API get_mtd_device_nm() and is used in mtdparts command.
This patch also avoids issue when the same NOR device is present 2 times,
for example on STM32MP15F-EV1:
STM32MP> mtd list
SF: Detected mx66l51235l with page size 256 Bytes, erase size 64 KiB, \
total 64 MiB
List of MTD devices:
* nand0
- type: NAND flash
- block size: 0x40000 bytes
- min I/O: 0x1000 bytes
- OOB size: 224 bytes
- OOB available: 118 bytes
- ECC strength: 8 bits
- ECC step size: 512 bytes
- bitflip threshold: 6 bits
- 0x000000000000-0x000040000000 : "nand0"
* mx66l51235l
- device: mx66l51235l@0
- parent: spi@58003000
- driver: jedec_spi_nor
- path: /soc/spi@58003000/mx66l51235l@0
- type: NOR flash
- block size: 0x10000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "mx66l51235l"
* mx66l51235l
- device: mx66l51235l@1
- parent: spi@58003000
- driver: jedec_spi_nor
- path: /soc/spi@58003000/mx66l51235l@1
- type: NOR flash
- block size: 0x10000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "mx66l51235l"
The same mtd name "mx66l51235l" identify the 2 instances
mx66l51235l@0 and mx66l51235l@1.
This patch fixes a ST32CubeProgrammer / stm32prog command issue
with nor0 target on STM32MP157C-EV1 board introduced by
commit b7f060565e ("mtd: spi-nor: allow registering multiple MTDs when
DM is enabled").
Fixes: b7f060565e ("mtd: spi-nor: allow registering multiple MTDs when DM is enabled")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
[trini: Add <dm/device.h> to <mtd.h> for DM_MAX_SEQ_STR]
Signed-off-by: Tom Rini <trini@konsulko.com>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Some drivers might want to execute code for each port at probe time, as
opposed to executing code just-in-time for the port selected for
networking.
To cater to that use case, introduce a .port_probe() callback method
into the DSA switch operations which is called for each available port,
at the end of dsa_port_probe().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
TCG EFI Protocol Specification defines the number_of_algorithms
field in spec ID event to be equal to the number of active
algorithms supported by the TPM device. In current implementation,
this field is populated with the count of all algorithms supported
by the TPM which leads to incorrect spec ID event creation.
Similarly, the algorithm array in spec ID event should be a variable
length array with length being equal to the number_of_algorithms field.
In current implementation this is defined as a fixed length array
which has been fixed.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
CC: Masahisa Kojima <masahisa.kojima@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr
support").
Fixes: 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The comment is no longer meaningful due to DT conversion, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Allow using different PHY interfaces for multiple USB controllers. When no
value is set in DT, we fall back to CONFIG_MXC_USB_PORTSC for now to stay
compatible with current board configurations.
This also adds support for the HSIC mode of the i.MX7.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
These definitions are unused, all boards that define portsc flags use
the equivalent PORT_* definitions instead.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
The MXC_EHCI_MODE_ definitions are redundant. Replace MXC_EHCI_MODE_SERIAL
with the equivalent PORT_PTS_SERIAL.
Only the zmx25 platform is affected.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Import usb_phy_interface enum values and DT match strings from the Linux
kernel.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Resetting an XHCI controller inside xhci_register undoes any register
setup performed by the platform driver. And at least on the Allwinner
H6, resetting the XHCI controller also resets the PHY, which prevents
the controller from working. That means the controller must be taken out
of reset before initializing the PHY, which must be done before calling
xhci_register.
The logic in the XHCI core was added to support the Raspberry Pi 4
(although this was not mentioned in the commit log!), which uses the
xhci-pci platform driver. Move the reset logic to the platform driver,
where it belongs, and where it cannot interfere with other platform
drivers.
This also fixes a failure to call reset_free if xhci_register failed.
Fixes: 0b80371b35 ("usb: xhci: Add reset controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated,
CONFIG_SYS_MAX_FLASH_BANKS is replaced by cfi_flash_num_flash_banks,
but this variable is defined in drivers/mtd/cfi_flash.c, which is
compiled only when CONFIG_FLASH_CFI_DRIVER is activated, in U-Boot
or in SPL when CONFIG_SPL_MTD_SUPPORT is activated.
This patch deactivates this feature CONFIG_SYS_MAX_FLASH_BANKS_DETECT
when flash cfi driver is not activated to avoid compilation issue in
the next patch, when CONFIG_SYS_MAX_FLASH_BANKS is used in spi_nor_scan().
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
nand_dt_init() is still using fdtdec_xx() interface.
If OF_LIVE flag is enabled, dt property can't be get anymore.
Updating all fdtdec_xx() interface to ofnode_xx() to solve this issue.
For doing this, node parameter type must be ofnode.
First idea was to convert "node" parameter to ofnode type inside
nand_dt_init() using offset_to_ofnode(node). But offset_to_ofnode()
is not bijective, in case OF_LIVE flag is enabled, it performs an assert().
So, this leads to update nand_chip struct flash_node field from int to
ofnode and to update all nand_dt_init() callers.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
We have individual SOC symbols for each keystone 2 platform. Use the
existing CONFIG_ARCH_KEYSTONE rather than CONFIG_SOC_KEYSTONE to
encompass all of the keystone families.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_OMAP_EHCI_PHY1_RESET_GPIO
CONFIG_OMAP_EHCI_PHY2_RESET_GPIO
CONFIG_OMAP_EHCI_PHY3_RESET_GPIO
To do this, we also introduce CONFIG_HAS_CONFIG_OMAP_EHCI_PHYn_RESET_GPIO
options to get setting the GPIO number.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have one places that uses this symbol and CONFIG_TARGET_OMAPL138_LCDK
works equally well, switch to that.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the main option for handling drivers/dma/keystone_nav* to Kconfig,
and enable it by default. All of the sub-symbols are not configurable,
so remove them from the CONFIG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
The COFNIG_KEYSTONE_RBL_NAND option is always enabled for the driver on
keystone platforms, but not older davinci platforms. Use def_bool for
the symbol. For CONFIG_KEYSTONE_NAND_MAX_RBL_PAGE, it's only used within
the driver and derived from another symbol, so remove CONFIG from the
name. Finally, CONFIG_KEYSTONE_NAND_MAX_RBL_SIZE is a bit more fixed.
For now, use the value directly. Long term, as part of DM'ifying NAND,
this should come from the device tree.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since cm_t35 was removed, CONFIG_CM_T3X does not exist. This lets us
simplify the code in board/compulab/common/eeprom.c a bit.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time, all platforms that had previously used
drivers/usb/phy/omap_usb_phy.c have been migrated to DM and related
options. Remove this now unused code and some related unused defines.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only used in the aemif driver that is otherwise currently
keystone2 centric. Moving forward, if this is applicable to some other
platform then such base addresses should be able to be obtained via the
device tree. Use KS2_AEMIF_CNTRL_BASE directly now rather than
indirectly.
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmFR2fMRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaAnAf/ZKPy3CRphbgAmbLhNQhQGpLosLcFp343
cv53gfsv1DakLRrhqMSnOQSVoTg9P22uHbooDDR9WHfZyEL6tvGZ+dgN2/wlDhDj
wbvvsM7FB+uvLVfMF3MURQBvy4dPO+FyCm/uHmry2V2uqWPw4ss+aVhxeQ5s4/oI
LpS6yaiM8UAj2GTUZSqJ1+/W7YG9N6tL73n0PDyCvSrdCkyPWqpww1rtST88SfFI
bBEWc6ksna/29haOwHQ2xopEbVxtHv2byULfqUtnsbtE4Ozw8o0fx66tdwPHTQlM
7eSuRiEbqjlJuUZFIbMat7nb7inZkaWupZ/Sr1HUUiDdKMygrRsQhg==
=x8Uf
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-next-27sep21' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
Various of-platdata improvements, including CONFIG_OF_REAL
There are two duplicated declarations for ft_cpu_setup() and
ft_pci_setup().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add support for accessing GPIOs using of-plata. This uses the same
mechanism as for clocks, but allows use of the xlate() method so that
the driver can interpret the parameters.
Update the condition for GPIO_HOG so that it is not built into SPL,
since it needs SPL_OF_REAL which is not enabled in sandbox_spl.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is available but not exported. More generally it does not
really work as intended.
Reimplement it and add a sandbox test too.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is actually a misnomer now, since the phandle info may contain
a driver_info index or a udevice index. Rename it to use the word
'phandle', which seems more accurate. Add a comment while we are here.
Also add a test for this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we have a 'positive' Kconfig option, use this instead of the
negative one, which is harder to understand.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current API is outdated as it requires a devicetree pointer.
Move these functions to use the ofnode API and update this globally. Add
some tests while we are here.
Correct the call in exynos_dsim_config_parse_dt() which is obviously
wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
TCG EFI Protocol Specification defines the number_of_algorithms
field in spec ID event to be equal to the number of active
algorithms supported by the TPM device. In current implementation,
this field is populated with the count of all algorithms supported
by the TPM which leads to incorrect spec ID event creation.
Similarly, the algorithm array in spec ID event should be a variable
length array with length being equal to the number_of_algorithms field.
In current implementation this is defined as a fixed length array
which has been fixed.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
CC: Masahisa Kojima <masahisa.kojima@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
vexpress_ca9x4 is seemingly the only board except for qemu_arm which
is able to run U-Boot correctly, using the `-M vexpress-a9` option to
QEMU. Building for qemu_arm and running qemu-system-arm with the `-M
virt` argument has a number of downsides, most importantly that it
only supports virtio storage drivers. This significantly reduces its
usefulness in testing memory card and Flash solutions, especially when
the tested images are from a third party source.
So therefore we reintroduce the vexpress_ca9x4 board in this commit,
with the explicit goal of using it with QEMU.
A number of differences to note from the original:
* Since the board was apparently unmaintained, I have now set myself
as the maintainer.
* The board has been converted to use the driver model, which was the
reason it was removed in the first place.
* The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed
in the same commit, are not necessary for the QEMU use case, and
have been omitted.
* An `mmc0` alias was introduced in the dts file. The mmc is not
detected correctly without this, now that it's based on the device
tree instead of the board's init function.
* A couple of other nodes were removed because they were problematic
when trying to run the UEFI bootmgr. Once again, the primary use
case here is QEMU, and these nodes are not needed for that to work.
* Unnecessary board init code has been removed, thanks to driver model
and device tree.
* `CONFIG_OF_EMBED` has been enabled. I know this goes against
recommended practice, but there doesn't seem to be any other way to
pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument
does not work, I suppose because U-Boot doesn't use the same
mechanics as the kernel when it's booting.
* Load addresses have been changed to fit QEMU use case.
People wanting to get a more detailed, yet somewhat isolated, diff
between this and the original, can run this command:
git diff c6c26a05b89f25a06e7562f8c2071b60fd0c9eac~1 -- \
$( git diff-tree --diff-filter=A -r --name-only HEAD~1 HEAD)
(Make sure to either check out this commit first, or replace HEAD with
the commit ID of this commit)
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr
support").
Fixes: 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The arc/arm/m68k/microblaze/mips/ppc arch_lmb_reserve() implementations
are all mostly the same, except for a couple of details. Implement a
generic arch_lmb_reserve_generic() function which can be parametrized
enough to cater for those differences between architectures. This can
also be parametrized enough so it can handle cases where U-Boot is not
relocated to the end of DRAM e.g. because there is some other reserved
memory past U-Boot (e.g. unmovable firmware for coprocessor), it is not
relocated at all, and other such use cases.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFKxpEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBLaB/0XsIdkGAvcHLWW8yUg
27GiRznikNKwn9/qIj2ByraoUd4BvxdQV4gKHR1R9n0sgYh/8VMyLbmhRoCRKFwP
3mQ0MUyjaeU5sEWzasovJVpXhuUapEiV0jEg6t3Lgwd3mp2QK2Pk87zoleQfZNkb
VAVCnt1T+kb3y0W9oa3XZbuH2wam9T5pNWRGW70JbgzdwJNKLO1Qo7MfcUNiDxJu
Jf7uXtYwwILlN38G1KSk1ymMjfaotCqj7RzNaV3Ero57MVj3VzerKGb7H+XPOYf2
nYXyietYLJJkzvHzSDwIdCSVlOSQL8QqVB8GCmLiNQD4tG830RcvSJnYpRLylWQK
6F+Y
=Q/aS
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.01 cycle:
This feature set includes : the support for CPU driver for arm926
(sam9x60 device); changes required for OP-TEE boot for sama5d2_xplained
and sama5d27_som1_ek boards; QSPI boot configuration for sama5d2_icp;
starting to remove old Kconfig unused symbols from config_whitelist.txt
(work will take more time); also small fixes and updates in mach, DT,
configs, etc.
The comment is no longer meaningful due to DT conversion, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Allow using different PHY interfaces for multiple USB controllers. When no
value is set in DT, we fall back to CONFIG_MXC_USB_PORTSC for now to stay
compatible with current board configurations.
This also adds support for the HSIC mode of the i.MX7.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
These definitions are unused, all boards that define portsc flags use
the equivalent PORT_* definitions instead.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
The MXC_EHCI_MODE_ definitions are redundant. Replace MXC_EHCI_MODE_SERIAL
with the equivalent PORT_PTS_SERIAL.
Only the zmx25 platform is affected.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Import usb_phy_interface enum values and DT match strings from the Linux
kernel.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Resetting an XHCI controller inside xhci_register undoes any register
setup performed by the platform driver. And at least on the Allwinner
H6, resetting the XHCI controller also resets the PHY, which prevents
the controller from working. That means the controller must be taken out
of reset before initializing the PHY, which must be done before calling
xhci_register.
The logic in the XHCI core was added to support the Raspberry Pi 4
(although this was not mentioned in the commit log!), which uses the
xhci-pci platform driver. Move the reset logic to the platform driver,
where it belongs, and where it cannot interfere with other platform
drivers.
This also fixes a failure to call reset_free if xhci_register failed.
Fixes: 0b80371b35 ("usb: xhci: Add reset controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add dt-bindings include file for Atmel Flexcom hardware block.
This file is copied from Linux kernel.
It is used in devicetrees from Linux.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
CONFIG_SYS_AT91_CPU_NAME looks to be unused.
Remove it and remove it from config_whitelist.txt
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Rewrite the CONFIG_BOOTCOMMAND only if it's not previously configured from
defconfig file.
This allows the user to select from defconfig/menuconfig the desired
boot command.
Adjust the current board defconfigs to reflect the default booting command
for the specific ENV configuration.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
When using OP-TEE, address range [0x20000000 - 0x22000000] is reserved.
This modification allows to have a system which always work even when
OP-TEE is present.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
When using OP-TEE, address range [0x20000000 - 0x22000000] is reserved.
This modification allows to have a system which always work even when
OP-TEE is present.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
This was unfortunately applied despite much discussion about it beiong
the wrong way to implement this feature.
Revert it before too many other things are built on top of it.
This reverts commit ddf67daac3.
Signed-off-by: Simon Glass <sjg@chromium.org>
The K3 SoCs have some PLL output clocks (POSTDIV clocks) which in
turn serve as inputs to other HSDIV output clocks. These clocks use
the actual value to compute the divider clock rate, and need to be
registered with the CLK_DIVIDER_ONE_BASED flags. The current k3-clk
driver and data lacks the infrastructure to pass in divider flags.
Update the driver and data to account for these divider flags.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The common TI SCI header file uses some macros from err.h and these
get exercised when CONFIG_TI_SCI_PROTOCOL is not defined. Include
the linux/err.h header file in this header file directly rather
than relying on source files to include it to eliminate any
potential build errors.
While at this, reorder the existing header file include to the
beginning of the file.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Header file version.h does not use anything from timestamp.h. Including of
timestamp.h has side effect which cause recompiling object file at every
make run because timestamp.h changes at every run.
So remove timestamp.h from version.h and include timestamp.h in files
which needs it.
This change reduce recompilation time of final U-Boot binary when U-Boot
source files were not changed as less source files needs to be recompiled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add in lib/acpi/acpi_table.c and test/dm/acpi.c, rework a few others]
Signed-off-by: Tom Rini <trini@konsulko.com>
Version string is available in global variable char version_string[].
Macro U_BOOT_VERSION_STRING is not used by any other file, so remove it
completely from version.h. Other files were already converted to use
variable version_string[].
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
More C files do not use compile time timestamp macros and do not have to be
recompiled every time when SOURCE_DATE_EPOCH changes.
This patch moves version_string[] from version.h to version_string.h and
updates other C files which only needs version_string[] string to include
version_string.h instead of version.h. After applying this patch these
files are not recompiled every time when SOURCE_DATE_EPOCH changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some tests produce a lot of output that does not need to be individually
checked by an assertion. Add a macro to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to map a file into memory so that it can be accessed using
simple pointers. Add a function to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to return the size of a file. This is useful in situations
where we need to allocate memory for it before reading it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
We are not guaranteed to have the padding_pkcs_15_verify symbol since
commit 92c960bc1d ("lib: rsa: Remove #ifdefs from rsa.h"), and
commit 61416fe9df ("Kconfig: FIT_SIGNATURE should not select RSA_VERIFY")
The padding_algos only make sense with RSA verification, which can now
be disabled in lieu of ECDSA. In fact this will lead to build failures
because of the missing symbol mentioned earlier.
To resolve this, move the padding_algos to a linker list, with
declarations moved to rsa_verify.c. This is consistent with commit
6909edb4ce ("image: rsa: Move verification algorithm to a linker list")
One could argue that the added #ifdef USE_HOSTCC is ugly, and should
be hidden within the U_BOOT_PADDING_ALGO() macro. However, this would
be inconsistent with the "cryptos" list. This logic for was not
previously explored:
Without knowledge of the U_BOOT_PADDING_ALGO() macro, its use is
similar to something being declared. However, should #ifndef
USE_HOSTCC be part of the macro, it would not be obvious that it
behaves differently on host code and target code. Having the #ifndef
outside the macro makes this obvious.
Also, the #ifdef is not always necessary. For example ecda-verify
makes use of U_BOOT_CRYPTO_ALGO() without any accompanying #ifdefs.
The fundamental issue is a lack of separation of host and target code
in rsa_verify. Therefore, the declaration of a padding algo with the
external #ifdef is more readable and consistent.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Note that we have to add CONFIG_SPIFLASH to scripts/config_whitelist.txt
because it's not really migrated at this point.
Acked-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Acked-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Acked-by: Oleksandr Zhadan and Michael Durrant <arcsupport@arcturusnetworks.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Handle CONFIG_SPIFLASH differently and delete Kconfig file]
Signed-off-by: Tom Rini <trini@konsulko.com>
Support using mmc command for enumerating mmc card in a given mode
Fix device_remove in mmc
Fix switch issue with send_status disabled
Drop 1ms delay in fsl_esdhc command sending
Revert "mmc: sdhci: set to INT_DATA_END when there are data"
