This patch modifies the meson clock driver to use syscon/regmap like
the Linux kernel does, as it is needed if we want to share the same
DTS files.
DTS files are synchronized from Linux 4.19.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Enable the HS400 support in DT on H3, M3W, M3N Salvator-X(S)
and ULCB boards as well as E3 Ebisu board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add regulators and pinmuxes for SDHI0 and SDHI1 SD and microSD
slots on E3 Ebisu and mark them as capable of up to SDR104 mode
of operation. With the SDHI fixes in place, it is now possible
to use SDR104.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable SDR104 modes on M3W and H3 boards. With the SDHI fixes
in place, it is now possible to use SDR104.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add pinmux entry for the eMMC DS line, as it is connected on these boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds the definitions need to use the USB OTG in rv1108
board. This has been tested using USB Mass Storage to export and
program a eMMC device.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds the pinctrl handles to enable the use of eMMC on custom
boards (as minievk) and makes it easier for later addition.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Some SanDisk Ultra cards trigger intermittent errors on detection
resulting in an -EOPNOTSUPP, when running at 50MHz.
Waveform analysis suggest that the level shifters that are used on the
RK3399-Q7 module (for voltage translation between the on-module
voltages and the 3.3V required on the card-edge) don't handle clock
rates at or above 48MHz properly. This change reduces the maximum
frequency on the external SD-interface to 40MHz (for a safety margin
of 20%).
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
- Some Kirkwood boards converted to DM_SPI by Chris
- New Armada-385 SoC revision printed by Chris
- Ethernet enable on mcbin by Baruch
- Support 2 DRAM banks on Armada-8k boards by Baruch
This configuration is useful when you want to run small u-boot and
perform DDR memory test to make sure that DDR is properly configured.
It is use for board bringup because alternative u-boot memory tests is
quite good.
Configuration is running out of OCM.
As is done for others mini configurations 0x80 bytes for variables is
enough and only default variables are stored there.
Alternative memtest is enabled and also 2GB of DDR via DTS files.
Configuration is enabling ZYNQMP_PSU_INIT_ENABLED and include psu_init()
from zcu102 for testing purpose.
In case of size issue this can be moved to SPL configuration as is done
for mini_qspi configuration but it is not a problem now.
Log:
U-Boot 2018.11-00268-gbd58b8ba8915 (Nov 29 2018 - 15:33:35 +0100)
Model: ZynqMP MINI
Board: Xilinx ZynqMP
DRAM: WARNING: Initializing TCM overwrites TCM content
2 GiB
EL Level: EL3
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This fixes the board's dts to supply SPL with QSPI info.
The EBV Socrates board has DIP switches to boot from SD card or
QSPI, so let's fix its defconfig to work for both cases.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add -u-boot.dtsi files to keep the current U-Boot behaviour:
- add u-boot,dm-pre-reloc where required
- disable watchdog
- set uart clock frequency
- add gpio bank-name properties
where appropriate:
- make qspi work (add alias for spi0, fix compatible for flash)
- enable usb (status okay, add alias for udc0)
Adapt board dts files that are not in Linux to keep their old
behaviour.
Change licenses to SPDX.
(Patman warnings/errors are in 1:1 copied files from Linux)
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
If there are more instances of si570 clock-output-names property
should be used for differentiation of clock output.
The patch is adding this optional properties for all zynqmp boards with
si570 chip.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This chip is on the board but handling should be done via firmware not
via Linux driver. Changing status property to keep it in the tree to
describe it instead of removing this node completely.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable reading tx and rx buswidth from DT via spi-uclass.
To get these from uclass spi-flash compatible string has to be added
to flash node.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DC4 board has qspi on it hence define and enable
qspi node for it.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds device tree for MT7623 development board - Bananapi R2
Detailed hardware information for BPI-R2 which could be found on
http://wiki.banana-pi.org/Banana_Pi_BPI-R2.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds MT7629 device tree and the includes it needs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add that node path in u-boot overlay dtsi file for now to keep
am335x-chiliboard.dts in sync with Linux.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import chiliSOM and chiliboard dts files from Linux v4.19. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Synchronize the Amlogic AXG Device Tree files and bindings include from
the recent Linux 4.20-rc1, because it includes patches fixing support for
U-boot.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Make sense to add controller ID to model name to have it visible through
the logs to know which controller is used by which configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
spi-rx-bus-width property is part of flash, so it should be moved
to flash node from qspi node. This patch fixes the incorrect read
of spi-rx-bus-width property by moving it to flash node.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SolidRun Clearfog GT-8K is based on Armada 8040.
https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k
The config file is identical to the Macchiatobin one
(mvebu_mcbin-88f8040_defconfig) with only the default device-tree
changed.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Sync the k3-am654 specific dts files from Linux next with tag
20181019. This changes are in queue for Linux v4.20-rc1
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some minor changes have been made to the AM3517-evm and the underlying
am3517.dtsi files. This patch re-sync's the DTS and DTSI files with
Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
This add the initial support of the broadcom reference
board bcm968580xref with a bcm6858 SoC.
This board has 512 MB of ram, 256 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm6858 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Based on the information from hardware schematics and orangepi
vendor orangepi H6 boards, One Plus and Lite2 shares common nodes
like axp805, uart, mmc0 etc. The common differences between them is
- One Plus, has Ethernet
- Lite2, has Wifi, USB3, CSI port.
So, add common orangepi nodes into sun50i-h6-orangepi.dtsi so-that
it case use on respective orangepi h6 board dts files.
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pinebook is a laptop produced by Pine64, with USB-connected keyboard,
USB-connected touchpad and an eDP LCD panel connected via a RGB-eDP
bridge from Analogix.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Pine64 LTS is an updated version of the Pine64, copying the
technical updates from the SoPine platform: LPDDR3 DRAM, eMMC socket and
soldered SPI flash chip, even the broken SD card detect pin has been copied.
Consequently this leads to the .dts (copied from the kernel) just including
the SoPine baseboard .dts, and the defconfig being almost identical.
Nevertheless the boards deserves a separate config.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update the .dts/.dtsi files from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date: Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sun50i-a64.dtsi changes introduced in Linux v4.19-rc1 changed the
compatible name for the syscon controller, dropping the generic "syscon"
fallback. Using this new DT node will make the Ethernet driver in every
older kernel (or non-Linux kernels) fail to initialise the MAC device.
To allow booting distribution kernels (from installer images via UEFI,
for instance), re-add the syscon compatible string as a fallback. This
works with both older and newer kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update the .dts/.dtsi file from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date: Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The new board version has the 2nd FPGA connected via CS# 0 instead of
2 on SPI bus 1. Change this setup in the DT accordingly. Please note
that this change does still work on the old board version because the
CS signal is not used on this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Add the "spi-flash" compatible string so that the generic sf_probe
driver can probe the SPI flash on the theadorable Armada-XP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 3c28576bb0 ("arm: dts: imx8qxp: fix build warining")
fixed the dts warning by removing the unnecessary
#address-cells/#size-cells, but the recommendation for regulators is not
to place them under "simple-bus", so move the reg_usdhc2_vmmc regulator
accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This is a large update of the AST2500 SoC DTS file bringing it to the
level of commit 927c2fc2db19 :
Author: Joel Stanley <joel@jms.id.au>
Date: Sat Jun 2 01:18:53 2018 -0700
ARM: dts: aspeed: Fix hwrng register address
There are some differences on the compatibility property names. scu,
reset and clock drivers are also different.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Banana Pi M2 Zero is a board by Sinovoip with Allwinner H2+ SoC, 16-bit
512MiB DDR3 memory, a MicroSD slot, two MicroUSB ports (one OTG and one
powering-only) and a miniHDMI port.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[jagan: Fixed board MAINTAINERS file]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Introduce dtsi for i.MX8QXP, since there is other variants i.MX8DX(P),
so add them there, because i.MX8QXP includes the dtsi of them.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Build the -u-boot variants of the device trees so they can be included
in Multi-DTB fitImage, which in turn allows us to build single U-Boot
image for multiple boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Xilinx DLC20 has I2C0 with EEPROM(1KB), UART1, GPIO, SD0 (EMMC 4GB),
USB0 device, ENET0, QSPI (16MB) and DDR(two of 256MB each).
Boards have mix of Winbond/ST QSPIs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds Device Tree for the Khadas VIM2 board.
The meson-gxm-khadas-vim2.dts is synchronized from Linux 4.18.10.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Commit 9faa43c4b5 ("ARM: dts: i.MX6UL: U-Boot specific dts for u-boot,
dm-spl") removes the u-boot,dm-spl properties from the imx6ul.dtsi file
and breaks the OPOS6UL board.
Add the u-boot,dm-spl properties into *-u-boot.dts files to make the
board boot again.
Fixes: commit 9faa43c4b5 ("ARM: dts: i.MX6UL: U-Boot specific dts for u-boot, dm-spl")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The CPLD is used to reset the ULCB and it was removed
during DT sync with Linux 4.17. Reinstate it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Sync with 14e21cb8f811 ("arm64: dt: hikey: Add optee node"
from Linux kernel.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
With the device trees doing most of the work of pin-muxing and
DM doing much of the peripheral initialization, this creates
new defconfig files for each of the Logic PD variants with
proper register settings/pin-muxing.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
The baseboards and SOM's are virtually identical to their DM37
counterparts, but OMAP36/37 and OMAP3 have some minor register
differences. With the boards being mostly driven by device trees
now, this synchronizes their respective device trees with linux-omap
for-next branch destined for 4.20 (or whatever the version after 4.19
will be called)
Signed-off-by: Adam Ford <aford173@gmail.com>
With the introduction of the omap serial driver, the need for some
of these U-Boot specific modifications is gone. This cleans up
this unnneeded stuff.
Signed-off-by: Adam Ford <aford173@gmail.com>
The device tree entries are from linux-omap's for-next branch
destined to me put into 4.20 (or whatever the version is after 4.19)
Signed-off-by: Adam Ford <aford173@gmail.com>
The I2C6 is used to communicate with the PMIC and it was removed
during DT sync with Linux 4.17. Reinstate it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.
The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
[picked from the identical linux patch
https://patchwork.kernel.org/patch/10609253/]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dwmmc controllers on rk3188 do not have idma support, so need to
use the fifo-mode and it my tests they became confused and stopped
working if the frequency was to high.
While I only tested in somewhat bigger steps, 32MHz for example
hung the controller, while reducing it to 16MHz worked just fine
and is reasonably fast to load a kernel from mmc.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XRFI
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
With the omap_mmc driver no longer supporting cd-inverted, this
patch removes all these references since they are not needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 5d9ef839f874f4e3923c8a9ae7b136c6c3912cd5
Author: Stefan Mavrodiev <stefan@olimex.com>
Date: Wed May 16 14:38:08 2018 +0300
ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board
Note:
- Update sun7i-a20-primo73.dts as per Linux, since
this dts is U-Boot specific.
- Drop sun7i-a20-olimex-som-evb-emmc.dts since no board
added for this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update all A10s/A13/gr8/r8devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commit:
commit 190e3138f9577885691540dca59c2f07540bde04
Merge: cafc87023b0d a7affb13b271
Author: Arnd Bergmann <arnd@arndb.de>
Date: Tue Mar 27 14:58:00 2018 +0200
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 590b0c0cfc6162aeebbf43eaafb9753b56df1532
Author: Pascal Roeleven <dev@pascalroeleven.nl>
Date: Fri Apr 20 12:21:12 2018 +0200
ARM: dts: sun4i: Fix incorrect clocks for displays
Note: Update pinctrl-0 for sun4i-a10-inet-3f.dts, sun4i-a10-inet-3w.dts
like other dts file since there dts file are U-Boot specific.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
If PCIe Mox module is connected we want to have PCIe node enabled
in U-Boot's device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove smi_pins definition since it is already in armada-37xx.dtsi.
Add assigned-clocks definitions to spi0.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
With the re-sync from Linux 4.18, several entries in
da850-evm-u-boot.dtsi are no longer necessary, so this patch
removes them.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add the minimum dt nodes required to boot. These nodes
will get deleted as kernel gets these nodes added in the
main dts files.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This commit fixes various devicetree warnings in the at91 devicetrees
like:
arch/arm/dts/sama5d36ek_cmp.dtb: Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
These warnings make buildman report failed builds for most of at91 boards.
Thus, fixing it.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
For at91family, makefile was building unwanted DTBs
Moved them under specific target configuration.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
When re-syncing the DTS files from the kernel, something caused
the MMC driver to no longer detect the MMC card. Undoing the
CD-invert appears to fix the issue.
Fixes: e6ea2390cd ("ARM: DTS: Resync LogicPD-Torpedo-37xx-devkit
with Linux 4.18-RC4")
Signed-off-by: Adam Ford <aford173@gmail.com>
Add the board DTS files for 14x14 EVK and 9x9 EVK. They are necessary
for converting to use u-boot DM driver.
Two -u-boot.dtsi are added to modify compatible string of SPI flash
device to "spi-flash".
Signed-off-by: Ye Li <ye.li@nxp.com>
On iMX7D SabreSD board, the QSPI has pins conflict with EPDC (default).
To use QSPI, users have to rework the board (de-populate R388-R391, R396-R399
populate R392-R395, R299, R300). So we add new DTS file and new defconfig
dedicated for QSPI.
Other changes to support the DM QSPI:
- Add QSPI node and alias spi0.
- Modify spi4 (spi-gpio) node and add alias spi5 for it to avoid req
conflict
- Add EPDC node in imx7d.dtsi and disable it in imx7d-sdb-qspi.dts to
align with kernel and also present the conflict.
- Add -u-boot.dtsi to modify compatible string of mx25l51245g@0 to
"spi-flash"
- Remove iomux settings of qspi in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
To support DM QSPI driver:
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI and DM SPI FLASH configurations
- Remove iomux settings of qspi1 in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
To support DM QSPI driver
- Add spi0 and spi1 alias for qspi1 and qspi2.
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI/QSPI relavent configurations
- Remove iomux settings of qspi2 in board codes which is not needed
for DM driver.
- Add sf default settings. So running "sf probe" can detect the flash
Signed-off-by: Ye Li <ye.li@nxp.com>
Fix warning below:
unnecessary #address-cells/#size-cells without "ranges" or child "reg"
property
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The NAND reset is missing from DT, so the reset manager cannot unreset the NAND.
Add the missing DT reset entry.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The UART clock frequency can be obtained from the clock framework by the
ns16550 driver, so drop this redundant DT node.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Flag timer clock as DM pre-reloc, so that a timer driver can be used and
it can extract information about it's clock rate using the clock framework.
This patch also moves some of the pre-reloc flags into the core dtsi file,
this is because the timer is not board specific, but rather is used on all
boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Since commit f2faffecb0, tegra: Convert to use binman
the dm-pre-reloc properties are removed.
This leads U-Boot not to enable the display on paz00
This patch restore the dm-pre-reloc properties allowing
the bootloader to output to the display panel
v4: - Spell project name as appropriate
v3: - Fix few typos
v2: - Add more characters to commit hash
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the pre-reloc DT markers to clock nodes needed in SPL and early
U-Boot stages. This is required to let the Arria10 clock driver start
early and provide clock information for UART and SDMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The A10 SoCDK is missing the I2C bus alias, so DM I2C cannot assign
the I2C bus a bus number. Add the missing alias.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The I2Cx resets are missing from DT, so the reset manager
cannot control them. Add the missing DT reset entries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add the GMAC0,1 OCP resets, which must also be ungated for those GMACs
to work and add GMAC2 reset and OCP resets which were missing altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The UART0 and UART1 resets are missing from DT, so the reset manager
cannot control them. Add the missing DT reset entries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The Altera reset manager block must be available very early on, since
it controls ie. UART resets. Flag it as pre-reloc.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Device trees need to have the serial console device available
before relocation and require a stdout-path in chosen at least
for SPL to have a console.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This patch fix the following warnings for for stm32f429
evaluation and discovery boards:
unnecessary #address-cells/#size-cells without "ranges" or
child "reg" property
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add ADC device tree node. This allows to get analog conversions on
stm32mp157.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update all A83T devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 221cb9fd2ee3042689fe0e6613d0f34eb46a5af6
Author: Mylène Josserand <mylene.josserand@bootlin.com>
Date: Fri May 4 21:05:44 2018 +0200
ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC
Note: bananapi-m3 and cubietruck-plus board dts files has
usb_otg enabled in U-Boot which were not present in Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch add the 4 LED available on the ED1 board and activated
gpio led driver.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a flash node to fix the detection of the memory IC.
With the changes introduced with commit 8fee8845e7
("enf_sf: reuse setup_flash_device instead of open coding it")
the SPI speed is now read from device-tree or a default value
is applied. This replaced the old behavior of setting the
SPI speed to CONFIG_ENV_SPI_MAX_HZ.
As this board didn't have a flash node, the default value
was applied to the SPI speed, producing an error when probing
the flash memory (speed too slow).
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GP24 and SBx81GT24 cards
cards collectively referred to as SBx81LIFXCAT in u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This is required so SPL and u-boot can boot from spi
flash devices that use the dm drivers.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use -u-boot.dtsi]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The same pinctrl node appears in the solidrun-microsom dtsi. Use that
instead.
Cc: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
This makes changes so the u-boot dts file is structured more
similar to the mainline linux dtsi file. It provides a minimal
common dts that can work for most boards based on the ClearFog
platform. Ethernet support is only supported for eth0 however
all devices are left enabled so u-boot can generate and
provide mac addresses for all of the network interfaces.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: rebase on recent changes]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
Use hardware description from the recently introduced microsom .dtsi
file to reduce duplication.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
Add the "spi-flash" compatible string so that the generic sf_probe
driver can probe the SPI flash on the SolidRun SOM.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Avnet Ultra96 is rebranded Xilinx zcu100 revC/D. Add new defconfig files
and point to origin internal board name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mini cse NOR configuration is running without PL that's why there is no
reason to enable clock to PL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add missing clocks property with fix clock-names property to be aligned
with emmc0 configuration and binding doc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
After some thought, I believe there is an unfortunate naming flaw in
binman. Entries have a position and size, but now that we support
hierarchical sections it is unclear whether a position should be an
absolute position within the image, or a relative position within its
parent section.
At present 'position' actually means the relative position. This indicates
a need for an 'image position' for code that wants to find the location of
an entry without having to do calculations back through parents to
discover this image position.
A better name for the current 'position' or 'pos' is 'offset'. It is not
always an absolute position, but it is always an offset from its parent
offset.
It is unfortunate to rename this concept now, 18 months after binman was
introduced. However I believe it is the right thing to do. The impact is
mostly limited to binman itself and a few changes to in-tree users to
binman:
tegra
sunxi
x86
The change makes old binman definitions (e.g. downstream or out-of-tree)
incompatible if they use the 'pos = <...>' property. Later work will
adjust binman to generate an error when it is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.
Add support for it.
The device tree is from Linux next-20180720.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner H6 is a new SoC from Allwinner features USB3 and PCIe
interfaces.
This patch adds support for it.
The corresponding DTSI file, from Linux next-20180720, is also
introduced.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Fix warning when compiling tegra30-beaver/-apalis.dts with latest DTC:
"Warning (avoid_unnecessary_addr_size): /pci/pch@1f,0: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property"
Signed-off-by: Tom Warren <twarren@nvidia.com>
One ls1012a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Adjust the NAND register size on Arria10 to reflect reality.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
In order to use the device tree for MMC, the card-detect pin
needs to be inverted. This patch places this into the
am3517-evm-u-boot.dtsi file to keep the main DTS and DTSI files
clean and in-sync with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
With the resync of the omap3.dtsi file, the reg-shift was removed
so it breaks the UART. Adding the reg-shift into the
am3517-evm-u-boot.dtsi keeps the reg-shift for U-Boot, but keeps
the dts/dtsi files clean from Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
There have been some significant changes to the DM37 SOM-LV device
tree. This patch re-syncs it with Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
There have been some refactoring of the DTS files for the Logic PD
DM37 Torpedo. This patch re-sync's the DTS files with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
There have been several minor changes to the OMAP3.dtsi, so this
patch re-syncs it with Linux. An addition include/dt-binding was
also brought with it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Several changes have been made to the AM3517-evm and the underlying
am3517.dtsi file. This patch re-sync's the DTS and DTSI files with
Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
The GPMI NAND IP seems to be the same as used in i.MX 6Quad. Use
the fsl,imx6q-gpmi-nand compatible string like Linux devices trees
are.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.17.5
(Linux commit 54fb3c180d05e9dfda892a93413514e99f0cbb19).
This will enable HDMI_5V for USB Amlogic Meson GXL P212 based boards.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Add support of stm32mp157c-ev1, the evaluation board with pmic stpmu1
(ev1 = mother board + daughter ed1) with device tree.
EV1 is the selected board by default in basic defconfig.
PS: CONFIG_PINCTRL_FULL activation avoid to increase
SYS_MALLOC_F_LEN (Early malloc usage: 2034)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- add a devicetree for each variant (mmc, spi, nand)
- drop unneeded code from board and bur/common
- drop unneeded stuff from config header files
- minor adaptions to be compliant with driver model (requesting gpio,..)
- harmonize the commandset over all brppt1 targets
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
This is needed for having access to the devices below this bus, most
important is uart and boot-device (spi, mmc, ...) in SPL stage.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of internal memory. This
configuration has only required qspi flash support and it
uses DCC as serial.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint OCM memory. This configuration
only has required parallel nor flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of memory. This configuration
has only required nand flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is only one chipselect on each connector.
Define it directly in board dts file.
There should be an option to use more chipselects via gpios.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Libretech ALL-H3-CC has a high density connector for attaching
an eMMC module. The module form factor and connection is specific
to Libretech, and has provisions for split vmmc/vqmmc (core and I/O)
voltage supplies, but this board does not wire the vqmmc side. The
H2+/H3/H5 SoCs do not support alternate I/O voltages for eMMC either.
Only 3.3V is supported. A specific module that ties vqmmc to vmmc,
with both at 3.3V, must be used.
Given that a) eMMC is not designed to be hotplugged, b) power is
always provided on the pins, and c) MMC controllers can deal with
missing cards, we can enable this by default. If a module is attached
it will be picked up by the system.
The device tree change was also submitted to the Linux Kernel and
has already been queued up for 4.19.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds qspi driver support for all ZynqMP ZCU102
boards.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Enable the gigabit ethernet for the Bananapi M2 Ultra board.
Tested on BananaPi M2 Berry (R40), custom board (V40)
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Add a device tree node for the Allwinner R40/V40 GMAC gigabit
ethernet interface.
The R40 SoC does not use the syscon register for GMAC settings.
The gigabit ethernet interface can only be routed to a fixed set of
pins.
Updated to match the Linux kernel's device tree.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
When the defconfig for the SoPine baseboard was added, there wasn't any
proper DT for the board yet, so we used the Pine64 DT as a placeholder.
Copy the DT file(s) meanwhile added in Linux over to U-Boot, and use
them in our defconfig.
This is as of v4.18-rc3, exactly Linux commit:
commit 7d556bfc49adddf2beb0d16c91945c3b8b783282
Author: Jagan Teki <jagannadh.teki@gmail.com>
Date: Mon Dec 4 10:23:07 2017 +0530
arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the .dts file for the various boards with an Allwinner H3 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit 721afaa2aeb860067decdddadc84ed16f42f2048 (HEAD)
Merge: 7c00e8ae041b 87815dda5593
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Mon Jun 11 17:57:38 2018 -0700
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
This also includes the OrangePi Zero .dts, which technically has an
Allwinner H2+ SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the .dts file for the various boards with an Allwinner H5 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit af5d05bdc99c211729cba0a3d5417bccfa308caf
Author: Neil Armstrong <narmstrong@baylibre.com>
Date: Tue Apr 24 13:47:14 2018 +0200
arm64: dts: allwinner: Add dts file for Libre Computer Board ALL-H3-CC H5 ver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the device tree files from the Linux tree as of v4.18-rc3,
exactly Linux commit:
commit 55c5ba5e49a0a124ed416880e8227b493474495e
Author: Chen-Yu Tsai <wens@csie.org>
Date: Tue Apr 24 19:34:22 2018 +0800
arm64: dts: allwinner: h5: Add cpu0 label for first cpu
Since the H3 and H5 are very similar (aside from the actual ARM cores),
they share most the SoC .dtsi and thus have to be updated together.
One tiny change is the removal of the "arm/" prefix from the include
path in the sun50i-h5.dtsi, which is needed because we don't share the
same sophisticated DT directory layout of Linux.
Also we need to fix up the board .dts files already, since the .dtsi
removes some pins, so the .dts can't reference them anymore. This is to
maintain bisectability.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the .dts files for the various boards with an Allwinner A64 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit 818668055c9d588c9a9d151e3b258ed1adacba0b
Author: Jagan Teki <jagan@amarulasolutions.com>
Date: Mon Apr 23 12:02:39 2018 +0530
arm64: dts: allwinner: a64: bananapi-m64: add usb otg
It updates the existing DT files, adds the newly added axp803.dtsi and
removes our temporary kludge file to get Ethernet support in U-Boot.
I left the amarula-relic alone, as this DT has not reached mainline yet.
The changes are not critical anyway, and the next sync will fix this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Updates the device tree file from the the Linux tree as of v4.18-rc3,
exactly Linux commit:
commit c1cff65f9b16b31e731e2e75bbe06638c86e1996
Author: Harald Geyer <harald@ccbib.org>
Date: Thu Mar 15 16:25:08 2018 +0000
arm64: dts: allwinner: a64: add simplefb for A64 SoC
This also pulls in the newly required include files for the clock and
reset bindings, also removes the now redundant part from our
*-u-boot.dtsi overlay file.
I kept the PWM node from U-Boot, as we recently gained this explicitly
for U-Boot's own usage and I don't want to regress here. This node is in
the queue for mainline Linux already, so the next sync will make it all
equal again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Commit 5dfd5607af2114047bd ("ARM: socfpga: Pull DRAM size from DT") get
memory size from DT. So, we need to update memory size in memory node.
Otherwise, it cause U-boot hang.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
The SPL can also parse the DRAM configuration node to figure out the
memory layout, make sure it is available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
This commit adds uCRobotics Bubblegum-96 board support. This board is
one of the 96Boards Consumer Edition platform based on Actions Semi
S900 SoC.
Features:
- Actions Semi S900 SoC (4xCortex A53, Power VR G6230 GPU)
- 2GiB RAM
- 8GiB eMMC, uSD slot
- WiFi, Bluetooth and GPS module
- 2x Host, 1x Device USB port
- HDMI
- 20-pin low speed and 40-pin high speed expanders, 6 LED, 3 buttons
U-Boot will be loaded by ATF at EL2 execution level. Relevant driver
support will be added in further commits.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This commit adds Actions Semi OWL SoC family support with S900 as the
first target SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The various Aries Embedded boards have been orphaned for a year and no
one has come forward to take care of them. Remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
fdt_file is looking for imx6ul-geam-kit.dtb but Linux
has imx6ul-geam.dtb, since Linux skipped -kit on file name
by below commit.
"ARM: dts: imx6ul-geam: Skip suffix -kit from dts name"
(sha1: 182de5ebce71e469cfa686fcdf08c9cbe11ece97)
So, due to this mismatch U-Boot failed to pick the
proper dtb which eventually break the Linux boot.
This patch fixed this mismatch by
- renaming dts files
- update config option to use new dtb file
- update fdt_file to new dtb file name
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Now that the clock-frequency information has been moved to the
driver, more DT sync is possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add regulator nodes and pinmux settings to the SDHI3 on E3 Ebisu
and enable HS200 mode on it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both the RAVB and SH ether driver now support parsing the PHY reset
GPIOs from both the PHY nodes and the MAC nodes, move the reset GPIOs
back into the PHY nodes to minimize DT difference between U-Boot and
Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The current state of RAVB driver expects the PHY reset GPIO in the
RAVB mode, move it back from the PHY node to avoid breakage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Follow Linux commit 10b62a2f785a (".gitignore: move *.dtb and *.dtb.S
patterns to the top-level .gitignore").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch prevents from the situation where we may end up with garbage
displayed on the LCD panel.
Such situation occurs when one performs "reboot -f" in Linux and then
stop in U-boot (or observe the garbage on the screen during boot up).
To prevent from such situation - the PWM pin is configured as GPIO and set
to LOW.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Orange Pi Zero Plus is an open-source single-board computer
using the Allwinner H5 SOC.
H5 Orangepi Zero Plus has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot
- 16MBit SPI Nor flash
- Debug TTL UART
- 1GBit/s Ethernet (RTL8211E)
- Wifi (RTL8189FTV)
- USB 2.0 Host
- USB 2.0 OTG + power supply
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.
H2+ Orange Pi R1 has
- Quad-core Cortex-A7
- 256MB DDR3
- micrSD slot
- 128MBit SPI Nor flash
- Debug TTL UART
- 100MBit/s Ethernet (H2+)
- 100MBit/s Ethernet (RTL8152B)
- Wifi (RTL8189ETV)
- USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add EtherAVB PHY reset on V3M Eagle to let the AVB driver unreset the PHY.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add EtherAVB pinmux node on V3M Eagle to set the pinmux configuration.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add device tree nodes for the Renesas RPC HF/QSPI controller
to R8A77990 E3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
dtc is showing some warnings and this change was also done in
the Linux kernel as "Input: gpio-keys - clean up device tree binding
example"
with this fragment in commit message
"Drop #address-cells and #size-cells, which are not required by the
gpio-keys binding documentation, as button sub-nodes are not devices."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch splits the current mini emmc configuration into emmc0
and emmc1 configurations because emmc is probed at boot time and on
systems which have only one interface mini configuration is failing on
unused interface. This patch also adds required clock node in dts and
enables CONFIG_MMC_SDHCI_ZYNQ through defconfig.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.17.0
This will enable USB on Amlogic Meson GXL Boards like Khadas VIM, P212 or
LibreTech-CC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The helios4 is built on the SolidRun Armada 38x SOM.
The port os based on the ClearFog board, using information from
https://github.com/helios-4/u-boot-marvell as well as dtb input
from https://github.com/helios-4/linux-marvell
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16
and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch shows how to enable driver model support for the LS-CHLv2 and
LS-XHL boards.
There are a couple of open questions:
- do I need the u-boot,dm-pre-reloc tags in the device tree?
- should mach/config.h define CONFIG_DM_SEQ_ALIAS?
- how can we split this patch or are there any other pending patches
which does the same and I didn't catch these.
This patch is based on the http://git.denx.de/u-boot-marvell.git (master
branch) and needs the following patches, which are still pending:
https://patchwork.ozlabs.org/patch/909618/https://patchwork.ozlabs.org/patch/909617/https://patchwork.ozlabs.org/patch/909973/
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
This switches the clearfog boards to use DM based gpio and i2c
drivers. The io expanders are configured via their device-tree
entries.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: add DT i2c aliases]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
u-boot,dm-pre-reloc was missing from pinctrl and it's
children node. causing failure to configure pin mux
before relocation.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Import the R8A77990 and Ebisu DTS from linux-next to get the latest
version. This makes AVB ethernet work in U-Boot since the ethernet
node is now present in DT, as well as GPIOs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
