Use imx6_src_get_boot_mode() instead of manually reading SBMR1. The
existing function has proper handling for software overrides of the
bootdevice which can happen, for example, when booting from an alternate
source using `bmode`.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The PDK2 board is capable of running both 100M and 1G ethernet. However,
the i.MX6 has only one ethernet MAC, so it is possible to configure
either 100M or 1G Ethernet. In case of 100M option, the PHY is on the
SoM and the signals are routed to a RJ45 port. For 1G the PHY is on
the PDK2 board with another RJ45 port. 100M and 1G ethernet use
different signal pins from the i.MX6, but share the MDIO bus.
This SoM board combination is used to demonstrate how to enable 1G
ethernet configuration.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
The FXL6408 GPIO expander manages critical devices,
including on-module USB hub. Configure the expander to
switch the USB hub into bypass mode, allowing to use
on-carrier-board USB hub.
Signed-off-by: Oleksandr Suvorov <cryosay@gmail.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Extension boards can be added to Compulab's iot-gate-imx8mm.
We implement extension board manager for detecting the extension
boards.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: uboot-imx <uboot-imx@nxp.com>
Obatin the SoC current temperature in print_cpuinfo().
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The DDRLOCKED bit in CGC2 DDRCLK will auto lock up and down by HW
according to DDR DIV updating or DDR CLK halt status change. So DDR
PCC disable/enable will trigger the lock up/down flow. We
need wait until unlock to ensure clock is ready.
And before configuring the DDRCLK DIV, we need polling the DDRLOCKED
until it is unlocked. Otherwise writing ti DIV bits will not set.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch implements enable_adc1_clk() to enable or disable the ADC1
clock on i.MX8ULP.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Get the MAC address from fuse bank5 word 3 and 4. It has
MSB first at lowest address, so have a reverse order with other
iMX used in mac.c
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When LPAV is allocated to RTD, the LPAV won't be reset. So we have to
reset DCNano and MIPI DSI in u-boot before enabling the drivers
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The LPAV is not allocated to APD when dual boot, so LPAV won't
reset when APD is reset. We have to explicitly reset the DDR,
otherwise its initialization will fail.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0
LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision.
A0.2 will fix the issue in ROM. But A0.1 we have to workaround
it in SPL by setting LPOSCCTRL BIASCURRENT again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the freescale vendor name from CPU revision print to align
with other i.MX platforms
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The setting does not have effect because we should set it after
power on the PS16 for NIC AV.
So move it after upower_init which has powered on all PS
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To avoid DCNANO underrun issue on high loading test, set its
read Qos on NIC_LPAV to highest
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board use IO9 of PCA6416 on LPI2C0 and TPM0 for MIPI DSI MUX and
backlight. However the LPI2C0 and TPM0 are M33 resources, in this
patch we simply access them, but this is a temporary solution.
We will modify it when M33 FW changes to set MIPI DSI panel as default
path and enable backlight after reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the DSI clock enable and disable with PCC reset used.
Add the LCD pixel clock calculation and configuration for DCNano
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Assign the PXP/HIFI4/EPDC to APD domain, otherwise APD not
able to receive interrupts from the modules.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When single boot, assign AP domain as the master domain of the LPAV.
Allocates LPAV master and slave resources like GPU, DCNano, MIPI-DSI
eDMA channel and eDMA request to APD
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
S400 enables RDC only when the DBD_EN is fused. Otherwise, the RDC
is allowed by all masters.
Current S400 has issue if the XRDC has released to A35, then A35 reset
will fail in ROM due to S400 fails to get XRDC.
So temp work around is checking the DBD_EN, if it is not fused, we
don't need to call release XRDC or TRDC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change boot device logic to also allow environment stored in fat and in
ext4 when booting from SD or from eMMC.
As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at env_get_location
to use IS_ENABLED instead for all modes, returning NOWHERE when no valid
mode is found.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Correct printf format for unsigned long long is %llx and not %llxx.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The imx28 uses following voltage supplies hierarchy:
VDD_5V (VDD_BAT) -> VDDIO -> VDDA -> VDDMEM
\-----> VDDD
One shall first enable DCDC on the parent source (VDDIO) and then
follow with its children.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Force selecting features present in SoC i.MX7ULP.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Return the root clock values for MXC_CSPI_CLK, MXC_I2C_CLK,
MXC_UART_CLK and MXC_QSPI_CLK.
At least for the I2C clock the missing support leads to a wrong
configured I2C frequency. The expected value is 100kHz but the resulting
value is about 1MHz.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Non GMAC's MDIO pins should have slew rate disabled for R(G)MII modes. Set
them accordingly in DT.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
This is the promised second part of the sunxi PR for 2022.04, albeit
technially outside of the merge window. We were working on this full
steam since the beginning of the year, and it deserves to be merged,
I think.
The main attraction is support for the F1C100s SoC, which sports a
venerable ARM926 core. Support for this SoC and the LicheePi Nano board
has been in Linux for years, and U-Boot patches were posted mid last
year already.
The new SoC using ARMv5 also means that the bulk of the new code should
not touch any existing boards, although we did some refactorings first,
of course, which actually cleans up some existing sunxi code.
Compile tested for all 160 sunxi boards, and briefly tested on BananaPi M1,
OrangePi Zero, Pine64 and Pine-H64. Tested by others on their boards,
including F1C100s and F1C200s devices.
Add device tree files for suniv and
Lichee Pi Nano it is a board based on F1C100s.
dt-bindings/dts are synced with 5.16.0
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add support for the suniv architecture, which is newer ARM9 SoCs by
Allwinner. The design of it seems to be a mixture of sun3i, sun4i and
sun6i.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add support for F1C100s internal dram controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch aims to add header files for the suniv.
The header files included add support for uart, and clocks.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Some Allwinner SoCs use ARM926EJ-S core.
Add Allwinner/sunXi specific code to ARM926EJ-S CPU dircetory.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Both armv7 and arm926ejs use this timer code so move it to mach-sunxi.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARMv7 start code has support for saving some boot params at the
entry point, which is used by some SoCs to return to BROM.
Port this to ARM926EJ-S start code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When we added Allwinner SoC support to ARMv8, we needed to pull in an
implementation of lowlevel_init() calling the C function s_init(), as
sunxi required it as this time.
The last few patches got rid of this bogus requirement, and as sunxi was
still the only user, we can now remove this lowlevel_init.S from ARMv8
altogether.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Currently we do some magic "SRAM setup" MMIO writes in s_init(), copied
from the original BSP U-Boot. The comment speaks of this being required
before DRAM access gets enabled, but there is no indication that this
would actually be required that early.
Move this out of s_init(), into board_init_f(). Since this actually only
affects a very few older SoCs, the actual code goes into the cpu/armv7
directory, to move it out of the way for all other SoCs.
This also uses the opportunity to convert some #ifdefs over to the fancy
IS_ENABLED() macros used in actual C code.
We keep the s_init() stub around for now, since armv8's lowlevel_init
still relies on it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
According to their TRMs, Cortex ARMv7 CPUs with SMP support require the
ACTLR.SMPEN bit to be set as early as possible, before any cache or TLB
maintenance operations are done. As we do those things still in start.S,
we need to move the SMPEN bit setting there, too.
This introduces a new ARMv7 wide symbol and code to set bit 6 in ACTLR
very early in start.S, and moves sunxi boards over to use that instead
of the custom code we had in our board.c file (where it was called
technically too late).
In practice we got away with this so far, because at this point all the
other cores were still in reset, so any broadcasting would have been
ignored anyway. But it is architecturally cleaner to do it early, and
we move a core specific piece of code out of board.c.
This also gets rid of the ARM_CORTEX_CPU_IS_UP kludge I introduced a few
years back, and moves the respective logic into the new Kconfig entry.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far all Allwinner based boards were doing some not-so-lowlevel-setup
in lowlevel's s_init() routine.
This includes the initial clock, timer and pinmux setup, among other
things. This is clearly out of the "absolute bare minimum to get started"
scope that lowlevel_init.S suggests for this function.
Since we have an SPL, which is called right after s_init(), move those
calls to our board_init_f() function. As we overwrite this only for
the SPL, this has the added benefit of not doing this setup *again*
shortly afterwards, when running U-Boot proper.
This makes gpio_init() to be called from the SPL only, so pull this code
into a CONFIG_SPL_BUILD protected part to avoid build warnings.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There is some code that tries to "reset" the SCTLR_ELx register early in
the boot process. The idea seems to be to guarantee some sane settings
that U-Boot actually relies on, for instance running in little-endian
mode, with the MMU off initially.
However the current code has multiple problems:
- For a start, no platform or config defines the symbol that would
enable that code.
- The code itself really only works if the bits that it tries to clear
are already cleared:
- If we run in big-endian mode initially, any previous loads would have
been wrong already. That applies to the (optional) relocation code,
but more prominently to the mask that it uses to clear those bits:
"ldr x1, =0xfdfffffa" looks innocent, but actually involves a memory
access to the literal pool, using the current endianness.
- If we run with the MMU enabled, we are probably doomed already. We
*could* hope that we are running with an identity mapping, but would
need to do some cache maintenance to avoid losing dirty cache lines.
- The idea of doing a read-modify-write of SCTLR is somewhat
questionable to begin with, because as the owner of the current
exception level we should initialise all bits of this register with a
certain fixed value.
- The code is unnecessarily complicated, and the function name is
misspelled.
While those problems *could* admittedly be fixed, the point that is does
not seem to be used at all at the moment tells me we should just remove
this code, and be it to not give a bad example.
If people care, I could introduce some proper SCTLR initialisation code.
We are about to work this out for the boot-wrapper[1] as we speak, but
apparently we got away without doing this in U-Boot ever since, so it
might not be worth the potential trouble.
[1] https://lore.kernel.org/linux-arm-kernel/20220114105653.3003399-7-mark.rutland@arm.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Setting LINUX_KERNEL_IMAGE_HEADER=y attempts to include an ARM64 Linux
kernel image header at the start of both U-Boot proper and SPL binaries.
However, some definitions that the image header uses are not included by
the SPL linker script, resulting in a build error. Include them the way
they are included in U-Boot proper's linker script to fix the error.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
The commit in the Fixes: tag below broke traffic through switch ports
where the SERDES protocol requires in-band autoneg and this requirement
isn't described in the device tree: SGMII, QSGMII, USXGMII (with
2500Base-X, in-band autoneg isn't supported).
The LS1028A-QDS boards are not yet ready for syncing their device trees
with Linux, since Ethernet is missing there (but has been submitted):
https://lore.kernel.org/lkml/20211112223457.10599-11-leoyang.li@nxp.com/
When agreement is reached for the Ethernet support in Linux, there will
be a sync for these boards as well. For now, just enable in-band autoneg
to fix the breakage.
Fixes: e3789a7262 ("net: dsa: felix: configure the in-band autoneg property based on OF node info")
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow device trees to be reused between Linux and U-Boot.
The source for these device trees is linux-next as of commit
bd8a9cd624c6 ("arm64: dts: ls1028a-rdb: update copyright"), which was
chosen because some changes needed to be done to the Linux DTs too,
before they could be shared:
https://lore.kernel.org/linux-arm-kernel/20211202141528.2450169-5-vladimir.oltean@nxp.com/T/#m6f63c92e75fa79a01144b2c2c6dc4776e7971395
There are two more commits on the RDB device tree which haven't been
picked up yet, because they have dependencies on the SoC device tree:
dd3d936a1b17 ("arm64: dts: ls1028a: add ftm_alarm1 node to be used as wakeup source")
b2e2d3e02fb6 ("arm64: dts: ls1028a-rdb: enable pwm0")
These will be picked up on the next resync.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reuse the scheme implemented by the Kontron SL28 boards in
commit d08011d7f9
("arm: dts: ls1028a: disable the PCIe controller by default")
and move the 'status = "okay"' lines for the PCIe controllers
inside a separate U-Boot dtsi for the LS1028A-RDB board. This way, the
existing Linux device tree can simply be dropped in.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no I2C peripheral on these buses on the reference design board,
and the Linux device tree does not enable them either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no SPI peripheral on the LS1028A-RDB, therefore no reason to
enable these nodes in the U-Boot device tree (and Linux does not enable
them either).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In a bit of a blunder, the blamed commit in the Fixes: tag below made
the mscc_felix switch driver look at the 'managed = "in-band-status"'
device tree property, forgetting that the U-Boot device tree had not
been updated to include that property, whereas the Linux one does.
The switch is therefore described in the device tree as not requiring
in-band autoneg, but the PHY driver for VSC8514 (drivers/net/phy/mscc.c)
still enables that feature. This results in a mismatch => no traffic.
This patch is a copy-paste of the Ethernet device tree nodes from Linux,
which resolves that issue. The device tree update also renames the
Ethernet PHY labels.
Fixes: e3789a7262 ("net: dsa: felix: configure the in-band autoneg property based on OF node info")
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The nodes in the NXP LS1028A-RDB device tree are out of order, regroup
them alphabetically to have a simple delta when the Linux device tree is
brought in.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LX2160A-RDB to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During this board's sync with Linux device trees, it was observed that
it doesn't use the same compatible string for the RTC node as in U-Boot.
This change makes the RTC compatible strings match, for a smoother sync.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The LS1028A-QDS board won't be synced with the Linux device trees right
now, since those are currently still in progress (Ethernet is missing).
However, while we're at converting the RDB, it can be observed that the
same RTC is present on the two boards, and the wrong compatible string
is used in both places. This change updates the RTC from the QDS to use
the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LX2160A-QDS to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LS1088A-RDB to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LS1088A-QDS to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Even not used by u-boot, this has to be inline with the hw and kernel dts.
U-boot partition table is defined by MTDPARTS_DEFAULT Kconfig.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Beside that mounted rgmii debug phy is 1000Mbps capable, the debug link
between the piggy board and the phy is 100Mbps only.
This leads to longer link establishment time when working in debug mode,
as phy tries to autoneg 1000Mbps.
This patch fixes the speed to 100Mbps and allows smother link establishment
time for the debug interface.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Although it isn't known what bit 0 in PHY reg 8 does, it's obvious that
it has to be set before read calibration and cleared afterwards. This is
already done for first rank, but not for second (copy & paste error.)
Fix it.
Fixes: f4317dbd06 ("sunxi: Add H616 DRAM support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Kconfig symbol is missing CONFIG_ prefix, so compiler will always
skip ODT configuration.
Fix symbol name.
Fixes: f4317dbd06 ("sunxi: Add H616 DRAM support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For sunxi boards with the AXP209, AXP221, AXP809, and AXP818 PMICs
(plus possibly others, I only confirmed the datasheets for these),
it is sometimes desirable to not boot whenever the device is
plugged in. An example would be when using the NTC CHIP inside a
PocketCHIP.
This provides a configurable option to check if bit 0 of
register 0 of the PMIC says it was powered because of a power button
press (0) or a plug-in event (1). If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[Andre: reword to speak of boot, remove #ifdefs]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The calls for flipping bits in the Allwinner pin controller registers
were using unnecessarily complex pointer arithmetic.
Improve readability by simplifying the expression.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The GPIO and pinctrl drivers need these setters for pin configuration.
Since they are DM drivers, they should not be using hardcoded base
addresses. Factor out variants of the setter functions which take a
pointer to the GPIO bank's MMIO registers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The return values of these functions are always zero, and they are
never checked. Since they are not needed, remove them.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
ROM supports cpsw_port2 for Ethernet boot and SPL stages continue to
download images on the same port, therefore there is no need to enable
cpsw_port1. Disable the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The definition of struct udphdr in include netinet/udp.h in the
musl library differs from the definition in the glibc library.
To use the same definition with musl the symbol _GNU_SOURCE has
to be defined.
Reported-by: Milan P. Stanić <mps@arvanta.net>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Move this over to use a writer file, moving the code from the x86
implementation.
There is no need to store a separate variable since we can simply access
the ACPI context.
With this, the original monolithic x86 function for writing ACPI tables
is gone.
Note that QEMU has its own implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update this function to the newer style, so we can avoid passing and
returning an address through this function.
Also move this function out of the x86 code so it can be used by other
archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Each board has its own way of creating this table. Rather than calling the
acpi_create_fadt() function for each one from a common acpi_write_fadt()
function, just move the writer into the board-specific code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Move this table over to use a writer function, moving the code from the
x86 implementation.
Add a pointer to the DSDT in struct acpi_ctx so we can reference it later.
Disable this table for sandbox since we don't actually compile real ASL
code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this table over to use a writer function, moving the code from the
x86 implementation.
Add a pointer to the DSDT in struct acpi_ctx so we can reference it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new ACPI writer to write the base tables at the start of the area,
moving this code from the x86 implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new ACPI writer to write the ACPI tables. At present this is all
done in one monolithic function. Future work will split this out.
Unfortunately the QFW write_acpi_tables() function conflicts with the
'writer' version, so disable that for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present acpi_setup_base_tables() both sets up the ACPI context and
writes out the base tables.
We want to use an ACPI writer to write the base tables, so split this
function into two, with acpi_setup_ctx() doing the context set, and
acpi_setup_base_tables() just doing the base tables.
Disable the writer's write_acpi_tables() function for now, to avoid
build errors. It is enabled in a following patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than keying everything off ACPIGEN, use the main
GENERATE_ACPI_TABLE option to determine whether the core ACPI code
is included. Make sure these option are not enabled in SPL/TPL since we
never generate tables there.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this option is missing a header file, a function prototype and
the qfw driver needs a header included.
Fix these problems so we can enable this option on sandbox. This will
increase the build coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is enabled for quite a few boards which don't create ACPI tables.
Tidy this up by dropping the option for some boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some ARM boards are using ACPI now. It seems that U-Boot should support
this method. Add ARM to the list of archs which can generate ACPI tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow this to be used on any arch. Also convert to using macros so that
we can check the CONFIG option in C code.
Signed-off-by: Simon Glass <sjg@chromium.org>
These have sadly found their way to ARM now. Allow any arch to support
generating ACPI tables.
Disable this for the tools build.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since commit 9855034397 ("fdt: Don't call board_fdt_blob_setup()
without OF_BOARD") board_fdt_blob_setup() is no more called on
STM32MP platforms in trusted boot which hangs during boot process.
Enable OF_BOARD flag to fix this issue.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add the partition name and remove the line number in error messages
of treat_partition_list() to provide correct information to user of
STM32CubeProgrammer.
The "line number" value was confusing because it is incorrect here;
the index in part_array[] is not aligned with the line number in
the parsed Layout file, because the empty lines and the lines beginning
by '#' are skipped during the first parsing in parse_flash_layout().
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Synchronize DH DHCOM DTs with Linux commit 25960cafa06e ("Linux 5.15.12").
There is no functional change to the resulting DTs. The eeprom0 alias and
PHY reset GPIO are now reinstated in SoM u-boot dtsi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Synchronize DH DHCOR DTs with Linux commit 25960cafa06e ("Linux 5.15.12").
There is no functional change to the resulting DTs. The eeprom0 alias is
now reinstated in SoM u-boot dtsi, the PHY reset GPIO is reinstated in AV96
u-boot dtsi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Device tree alignment with Linux kernel v5.16-rc5
- ARM: dts: stm32: set otg-rev on stm32mp151
- ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
- ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
- ARM: dts: stm32: fix SAI sub nodes register range
- ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Default value for CONFIG_SYS_BOOTCOUNT_SINGLEWORD and
CONFIG_SYS_BOOTCOUNT_ADDR are only needed when
CONFIG_BOOTCOUNT_GENERIC is used.
This patch avoids to define these configs when an other bootcount backend
is activated, for example for CONFIG_BOOTCOUNT_ENV.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Today the bootcount is not managed by the Linux kernel for STM32MP15 as
we don't have driver to update the used backup register in TAMP and the
recovery command still executes the normal bootcmd with
'altbootcmd=run bootcmd'.
So the bootcount feature is never used, the config CONFIG_BOOTCOUNT_LIMIT
and the associated environment variable 'altbootcmd' can be removed to
reduce the U-Boot size.
Each boards can re-enable this feature later in their defconfig, if it is
needed, with the expected backend, for example CONFIG_BOOTCOUNT_GENERIC
or CONFIG_BOOTCOUNT_ENV.
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case the SoC reports the boot device type is USB, it means the SPL was
loaded via BootROM DFU mode. Currently the spl_boot_device() returns boot
device as USB host, change it to DFU instead, so the SPL can continue the
DFU boot and load U-Boot via DFU.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When booting from QSPI, the boot ROM appears to mux the QSPI
pins, but it's not guaranteed to be setup when booting from
eMMC. Fix this by explicitly configuring the pinmux.
Signed-off-by: Adam Ford <aford173@gmail.com>
Documentation:
* describe printf() format codes
UEFI
* enable more algorithms for UEFI image verification, e.g. SHA256-RSA2048
General
* simplify printing short texts for GUIDs
* provide a unit test for printing GUIDs
-----BEGIN PGP SIGNATURE-----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=GoR6
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc1-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1-2
Documentation:
* describe printf() format codes
UEFI
* enable more algorithms for UEFI image verification, e.g. SHA256-RSA2048
General
* simplify printing short texts for GUIDs
* provide a unit test for printing GUIDs
This converts the following to Kconfig:
CONFIG_AT91_EFLASH
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Use the preferred
if (IS_ENABLED(X))
instead of
#ifdef X
where possible.
There are still places where this is not possible or is more complicated
to convert in this file. Leave those be for now.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Checkpatch warns about using uint32/16/8_t instead of u32/16/8.
Use the preferred types.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Print the wrong srcaddr (spl_image->offset) in error message also for
SATA case.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Last 4 bytes of kwbimage boot image is checksum. Verify it via the new
spl_check_board_image() function which is called by U-Boot SPL after
loading kwbimage.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Each boot mode has its own kwbimage specified by blockid. So check that
kwbimage is valid by blockid.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
There are certain restrictions for kwbimage offset and blocksize.
Validate them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Kirkwood uses macros KW_DEFADR_PCI_MEM and KW_DEFADR_PCI_IO for base
address of PCIe mappings. Size of PCIe windows is not defined in any macro
yet, so export them in new KW_DEFADR_PCI_MEM_SIZE and KW_DEFADR_PCI_IO_SIZE
macros.
Kirkwood arch code already maps mbus windows for io and mem, so avoid
calling mvebu_mbus_add_window_by_id() function which would try to do
duplicate window mapping.
Kirkwood PCIe controllers already use "marvell,kirkwood-pcie" DT compatible
string, so mark pci_mvebu.c driver as compatible for it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
CONFIG_PARTITION_TYPE_GUID=y is needed for testing some GPT related
functionality.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
There are 4 MDIO bus controllers in AST2600 SOC. Each of them can
connect to one or more PHY chips and is flexible to work with the 4 MAC
devices in AST2600. On AST2600 EVB, MDIO 0,1,2,3 connect to the PHY
chips used by MAC 0,1,2,3 respectively.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch adds node for mmc/sd controller found on Action Semi OWL
S700 SoC.
Since, upstream Linux binding has not been merged for S700 MMC/SD
controller, Changes are put in u-boot specific dtsi file.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This Synchronizes the Actions Semi S700 SoC DT changes from
commit "g58e1100fdc59" ("Linux v5.16-rc3").
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Add a return value to init_addr_map and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Commit 98f705c9ce ("powerpc: remove 4xx support") removed (in 2017) the
last code that made use of bedbug debugger support. Since there aren't
any boards left that define either CONFIG_CMD_BEDBUG or a real
bedbug_init(), drop this feature from u-boot.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Factor out armv7m fragment to spl_perform_fixups(), which is an arch/board
specific function designed for this purpose.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmHlNOccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyL0JB/4+sKNWPMgOYvP2uLCC
euRGomhxJ5WmxJVDtJeBIRg0YKSkwnE8JwIN2qqGu15xJnNX9Ck5qnIMPbiZ/io9
ocW5Z/4C4rfJX/OzD6FtmbMNsvG/umVmZkjRU3ryRXKGyNVpVjLQ2EEECaJfk1WZ
Nd/J6/Jo8nafb1x4OeY+F6+xwZAuj7Mrun9SsDSyrIvmEqSnaQNioj+lStkauL51
NwQgBxZBQmbdCgF7Ooy6rYlXZBR6r/rgWB9n3RP8emDCwfCMul9HOMT432oKNbhW
bGrcMu9AWv/pgzXogxSzYbEdTAnoVEODtU1suCa8LV6KJPEG693gARnRm/KjvPHa
FfsK
=39IY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.04 cycle:
This small feature set includes few changes for sama7g5 and sama7g5ek:
turn blue led on at boot, changes required for the Rev4 of the board,
better sync with the Linux DT with regards to the new DT nodes.
The rev4 of the board sama7g5ek has the eeproms on flexcom8 instead of
flexcom1.
Initialize flexcom8 with required pincontrol and move the eeproms accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add Flexcom8 node with required referenced nodes as phandles.
Since Flexcom8 is present in Linux, take the node exactly as-is from Linux.
Some nodes are referenced in Linux as phandles, the dma and the gic.
Add them as well to the file, even if they are unused by Uboot.
This is a step towards having the U-boot DT equivalent with the DT in Linux.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This driver supports power domains for the power management
controller found on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These are necessary to make sure the power domains needed for the
serial console are availble in the pre-relocation phase.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This synchronizes the device trees with those that are in the
process of being upstreamed into Linux. This is mostly the
current state of the device trees on the asahilinux branch
with a few extra bits used by OpenBSD. This includes device
trees for machines that were still missing.
There are still some differences that will hopefully be resolved
soon.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Probe toplevel AM65 CPSW NUSS driver from misc_init_r() when driver
is enabled. Since driver is modeled as UCLASS_MISC, we need to
explicitly probe the driver. Use common misc_init_r() that entire
K3 family of SoCs.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
In case of xSPI bootmode OSPI flash is in DDR mode and needs to be accessed
in multiple of 16bit accesses Hence we cannot parse sysfw.itb FIT image
directly on OSPI flash via MMIO window. So, copy the image to internal
on-chip RAM before parsing the image.
Moreover, board cfg data maybe modified by ROM/TIFS in case of HS platform
and thus cannot reside in OSPI/xSPI and needs to be copied over to
internal OCRAM.
This unblocks OSPI/xSPI boot on HS platforms
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Dave Gerlach <d-gerlach@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Currently only the PADCFG registers of the main domain are unlocked.
Also unlock PADCFG registers of MCU domain, so MCU pin muxing can be configured by u-boot or Linux.
Signed-off-by: Michael Liebert <liebert@ibv-augsburg.de>
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
Documentation:
* Fix building HTML documentation of readthedocs.io
* Add ARM Juno board documentation
* Build requirements for Alpine Linux
* Include DM headers in API documentation
UEFI:
* Fix section alignment of EFI binaries
* Fix header length of RISC-V EFI binaries allowing to run them on EDK II
* Remove kaslr-seed from device tree if the EFI_RNG_PROTOCOL is provided
Other:
* Let 'part list' show all 128 GPT partitions
-----BEGIN PGP SIGNATURE-----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=NZ+6
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1
Documentation:
* Fix building HTML documentation of readthedocs.io
* Add ARM Juno board documentation
* Build requirements for Alpine Linux
* Include DM headers in API documentation
UEFI:
* Fix section alignment of EFI binaries
* Fix header length of RISC-V EFI binaries allowing to run them on EDK II
* Remove kaslr-seed from device tree if the EFI_RNG_PROTOCOL is provided
Other:
* Let 'part list' show all 128 GPT partitions
At present some 32-bit settings are used with the 64-bit app. Fix this by
separating out the two cases.
Be careful not to break the 64-bit payload, which needs to build a 64-bit
EFI stub with a 32-bit U-Boot.
Signed-off-by: Christian Melki <christian.melki@t2data.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
That script is not intended for use with EFI, so update the logic to avoid
using it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christian Melki <christian.melki@t2data.com>
Add an empty CPU init function to avoid fiddling with low-level CPU
features in the app. Set up the C runtime correctly for 64-bit use
and avoid clearing BSS, since this is done by EFI when U-Boot is loaded.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function requires a pointer to struct efi_entry_memmap
but the only field used in there is the desc_size. We want to be able
to use it from the app, so update it to use desc_size directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
The alignment of sections in the EFI binaries generated by U-Boot is
incorrect.
According to the PE-COFF specification [1] the minimum value for
FileAlignment is 512. If the value of SectionAlignment is
less then the page size, it must equal FileAlignment.
Let's set both values to 512 for the ARM and RISC-V architectures.
[1] https://docs.microsoft.com/en-us/windows/win32/debug/pe-format
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
EDK II refuses to load the EFI binaries created by U-Boot.
The reason is an incorrect PE-COFF header. The number of
data directories does not match NumberOfRvaAndSizes.
This leads to a failed consistency check in
PeCoffLoaderGetPeHeader():
SizeOfOptionalHeader - HeaderWithoutDataDir) !=
NumberOfRvaAndSizes * sizeof(DATA_DIRECTORY))
Fixes: 9afaeec6ef ("riscv: Complete efi header for RV32/64")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Apple's ARMv8 cores don't implement EL3 and therefore don't
provide a PSCI implementation. So don't attempt to use
PSCI to reset on machines using Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
BootROMs on pre-A38x SoCs enabled its output on UART by default, but A38x'
BootROM has its output on UART disabled by default.
To enable BootROM output on A38x SoC, it is required to set DEBUG flag
(which only enables BootROM output and nothing more) in kwbimage. For UART
images this DEBUG flag is ignored by BootROM.
Enable kwbimage DEBUG flag for all A38x boards.
With this change BootROM prints the following (success) information on UART
before booting U-Boot kwbimage:
BootROM - 1.73
Booting from SPI flash
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
U-Boot SPL for mvebu platform is not compiled as position independent.
Therefore it is required to instruct BootROM to load U-Boot SPL at the
correct address. Loading of kwbimage binary code at specific address can be
now achieved by the new LOAD_ADDRESS token as part of BINARY command in
kwbimage config file.
Update mvebu Makefile to put value of $(CONFIG_SPL_TEXT_BASE) into
LOAD_ADDRESS token when generating kwbimage.cfg from kwbimage.cfg.in.
It is required to update regex for sed to find replacement tokens at any
position on a line in kwbimage config file and not only at the beginning of
the line. This is because LOAD_ADDRESS is specified at the end of line
containing the BINARY command.
It looks like all Armada boards set CONFIG_SPL_TEXT_BASE to value
0x40004030 or 0x40000030. Why this value? It is because main kwbimage
header is at address 0x40004030 or 0x40000000 and it is 32 bytes long.
After the main header there is the binary header, which consist of 1 byte
for type, 3 bytes for size, 1 byte for number of arguments, 3 reserved
bytes and then 4 bytes for each argument. After these arguments comes the
executable code.
So arguments start at address 0x40004028 or 0x40000028. Before commit
e6571f38c9 ("arm: mvebu: Remove dummy BIN header arguments for SPL
binary") there were two (dummy) arguments, which resulted in load address
of 0x40004030 or 0x40000030, always. After that commit (which removed dummy
arguments), load address stayed same due to the 128-bit alignment done by
mkimage.
This patch now reflects the dependency between $(CONFIG_SPL_TEXT_BASE),
load address and dummy kwbimage arguments, and allows the user to adjust
$(CONFIG_SPL_TEXT_BASE) config option to some other value.
For unsupported values, when mkimage/kwbimage cannot set chosen load address
as specified by $(CONFIG_SPL_TEXT_BASE), the build process now fails,
instead of silently generating non-working kwbimage.
Removal of this alignment between $(CONFIG_SPL_TEXT_BASE) and LOAD_ADDRESS
can only be done by compiling U-Boot SPL as position independent. But this
currently is not possible for 32-bit ARM version of U-Boot SPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Usage of $(call cmd,...) is standard way to call other commands which
generate things.
It also has the advantage of printing build information in the form
KWBCFG arch/arm/mach-mvebu/kwbimage.cfg
if verbosity is disabled, and printing the build command otherwise.
Note that the '#' character needs to be escaped in Makefile when used as
value for make variable assignment.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The DT properties for the "enable-arbiter" and "keep-config" config
knobs were previously named inconsistently:
- The u-boot driver used "nand-enable-arbiter" and "nand-keep-config"
names, without Marvell prefixes.
- The Linux driver uses "marvell,nand-keep-config" ("enable-arbiter"
does not exist anymore in recent kernels, but it also used to be
"marvell,nand-enable-arbiter").
- The device trees almost all use "marvell," prefixed names, except for
one single instance of "nand-enable-arbiter" without vendor prefix.
This commit standardizes on the vendor prefixed version, making the
u-boot driver read from DT props "marvell,nand-enable-arbiter" and
"marvell,nand-keep-config". The one device tree using the unprefixed
version is also changed to use the new naming.
This has the side effect of making the previously no-op "marvell,"
config knobs already present in some DTs actually do something. This was
likely the original intention of the DT authors, but note that this
commit was not tested on every single impacted board.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
As explained in commit 3bedbcc3aa ("arm: mvebu: a38x: serdes: Don't
overwrite read-only SAR PCIe registers") it is required to set Maximum Link
Width bits of PCIe Root Port Link Capabilities Register depending of number
of used serdes lanes. As this register is part of PCIe address space and
not serdes address space, move it into pci_mvebu.c driver.
Read number of PCIe lanes from DT property "num-lanes" which is used also
by other PCIe controller drivers in Linux kernel. If this property is
absent then it defaults to 1. This property needs to be set to 4 for every
mvebu board which use PEX_ROOT_COMPLEX_X4 or PEX_BUS_MODE_X4.
Enabling of PCIe port needs to be done afer all registers in PCIe address
space are properly configure. For this purpose use new mvebu-reset driver
(part of system-controller) and remove this code from serdes code.
Because some PCIe ports cannot be enabled individually, it is required to
first setup all PCIe ports and then enable them.
This change contains also all required "num-lanes" and "resets" DTS
properties, to make pci_mvebu.c driver work correctly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Enabling and disabling PCIe ports is done via address space of system
controller. All 32-bit Armada SoCs use low 4 bits in SoC Control 1 Register
for enabling and disabling some or more PCIe ports. Correct mapping needs
to be set in particular DTS files.
DT API for mvebu-reset is prepared for implementing resets also for other
HW blocks, but currently only PCIe is implemented via index 0.
Currently this driver is not used as PCIe ports are automatically enabled
by SerDes code executed by U-Boot SPL. But this will change in followup
patches.
Signed-off-by: Pali Rohár <pali@kernel.org>
Do not call pci_set_region() for resources which were not properly mapped.
This prevents U-Boot to access unmapped memory space.
Update MBUS_PCI_MEM_SIZE and MBUS_PCI_IO_SIZE macros to cover all PCIe MEM
and IO ranges. Previously these macros covered only address ranges for the
first PCIe port. Between MBUS_PCI_IO_BASE and MBUS_PCI_MEM_BASE there is
space for six 128 MB long address ranges. So set MBUS_PCI_MEM_SIZE to value
of 6*128 MB. Similarly set MBUS_PCI_IO_SIZE to 6*64 KB.
Function resource_size() returns zero when start address is 0 and end
address is -1. So set invalid resources to these values to indicate that
resource has no mapping.
Split global PCIe MEM and IO resources (defined by MBUS_PCI_*_* macros)
into PCIe ports in mvebu_pcie_bind() function which allocates per-port
based struct mvebu_pcie, instead of using global state variables
mvebu_pcie_membase and mvebu_pcie_iobase. This makes pci_mvebu.c driver
independent of global static variables (which store the state of
allocation) and allows to bind and unbind the driver more times.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The only user of board_pex_config() weak function is A385 controlcenterdc
board. It looks like that code in its board_pex_config() function needs to
be executed after PCIe link is up. Therefore put this code into
spl_board_init() function which is called after a38x serdes initialization,
and therefore it is after the serdes hws_pex_config() function finishes
(which is the state before this change).
With this change completely remove board_pex_config() function as it is not
used anymore.
Signed-off-by: Pali Rohár <pali@kernel.org>
U-Boot define loff_t as long long. But the header
/usr/include/linux/types.h may not define it.
This has lead to a build error on Alpine Linux.
So let's use long long instead of loff_t for
the size parameter of function os_get_filesize().
Reported-by: Milan P. Stanić <mps@arvanta.net>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rely on the new watchdog timer driver and the sysreset uclass to
reset the system. This gets rid of hard-coded addresses and
should work on systems based on the new M1 Pro and M1 Max SoCs
as well.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-on: Apple M1 Macbook
Tested-by: Simon Glass <sjg@chromium.org>
Add a node for the watchdog timer based on the proposed Linux
device tree bindings.
Remove the old reboot node which was a watchdog timert node in
disguise using a preliminary device tree binding.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-on: Apple M1 Macbook
Tested-by: Simon Glass <sjg@chromium.org>
a7y17lte is called SM-A720F, and a3y17lte SM-A320F. a3y17lte also
should select PINCTRL_EXYNOS78x0, not the (non-existent)
PINCTRL_EXYNOS7880, and it has an Exynos 7870 SoC and not 7880.
Fixes: 3e2095e960 ("board: samsung: add support for Galaxy A series
of 2017 (a5y17lte)")
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
mcf5445x platform uses standard format of Config Address for PCI
Configuration Mechanism #1. So use new U-Boot macro PCI_CONF1_ADDRESS().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
x86 platform uses standard format of Config Address for PCI Configuration
Mechanism #1. So use new U-Boot macro PCI_CONF1_ADDRESS().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
All i.MX8MQ boards have been converted to binman, which makes it
necessary to flash both flash.bin and u-boot.itb to get a bootable
system. Prior to the conversion, only flash.bin was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single bootable
binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone (for
example, for secure boot purposes).
Also update imx8mq_evk.rst to remove the u-boot.itb copy step.
This is a cherry-pick of 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") adjusted to apply to i.MX8MQ.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
CMD_DM is useful for showing the whole DM tree.
Enable it via "imply CMD_DM".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
The binman node is part of the imx8mm-u-boot.dtsi file which
is duplicated in imx8mm-kontron-n801x-s-u-boot.dtsi and causes
a build error. Remove the duplicate.
Fixes: 3cbb31f0e848 ("arm64: dts: imx8mm: use common binman configuration")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The binman node is part of the imx8mm-u-boot.dtsi file which
is duplicated in phycore-imx8mm-u-boot.dtsi and causes a build
error. Remove the duplicate.
Fixes: 3cbb31f0e848 ("arm64: dts: imx8mm: use common binman configuration")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Use binman to pack images.
Note that imx8mm_venice supports several boards via multiple DTB's thus
in the fit node we must use:
- fit,fdt-list = "of-list"
- fdt-SEQ
- config-SEQ
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Rather than using odd implicit blob-ext naming, explicitly specify the
type to be of blob-ext and therefore also simplify the node naming.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
With the move to using binman to generate SPL aka u-boot-spl-ddr.bin and
U-Boot proper aka u-boot.itb every board now covers such configuration
in its own U-Boot specific device tree include. Move the comon part of
that configuration to the common imx8mm-u-boot.dtsi include file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
After all these board switch to binman, we could use common imximage.cfg
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Somewhere along the line, the board stopped being able to boot.
Rather than just fixing the issue, let's fix the issue and migrate
to binman to eliminate a warning when using custom imx tools for
generating the binary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
To eliminate a warning when using custom imx tools for generating
a binary, use binman to generate flash.bin.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Current code assumes that the vector base address is always at 0x0.
However, this value is configurable for MicroBlaze using the
CONFIG_XILINX_MICROBLAZE0_VECTOR_BASE_ADDR Kconfig option. Update the
reset routines to branch to this location instead.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-10-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current code assumes that the vector base address is always at 0x0.
However, this value is configurable for MicroBlaze, so update the
__setup_exceptions routine to work with any vector base address.
The r4 register is reserved for the vector base address inside
__setup_exceptions and the function prologe/epilogue are also updated to
save and restore r4.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-9-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-7-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze is one the last two users of the CONFIG_SYS_RESET_ADDRESS
macro (the other is arch/powerpc/cpu/mpc8xx/cpu.c, but the macro is not
defined anywhere in powerpc code, so it should be removed there too).
Replace CONFIG_SYS_RESET_ADDRESS usage in start.S with
CONFIG_SYS_TEXT_BASE. If the reset address should really be
user-configurable, a new Kconfig option could be added.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-6-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
To simpify the code, use stack space as scratch memory for endian offset
calculation, rather than saving/restoring the first unused MB vector.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-5-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable SPL_LIBCOMMON_SUPPORT and SPL_LIBGENERIC_SUPPORT if CONFIG_SPL=y, in
order to fix the following link failures:
common/spl/spl.o: in function `board_init_r':
common/spl/spl.c:755: undefined reference to `puts'
...
common/spl/spl.o: in function `board_init_r':
common/spl/spl.c:756: undefined reference to `hang'
common/spl/spl.c:740: undefined reference to `memset'
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-4-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze has three boot modes defined in microblaze/include/asm/spl.h,
but only booting from NOR flash is currently useable. Add a custom
board_boot_order() implementation so that RAM and SPI boot modes can also
be selected if the corresponding load-image support is present.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-3-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_fdt_blob_setup() uses the _end symbol to find the dtb in the non-spl
case. In order to allow microblaze builds to compile successfully with
CONFIG_OF_SEPARATE, the _end symbol must be defined. Align microblaze with
the other architectures and use _end symbol rather than __end to mark the
end of the u-boot binary.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-2-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP modepin driver has capability to get/set/check status of modepin
gpios. These modepins are accessed using xilinx firmware. In modepin
register, [3:0] bits set direction, [7:4] bits read IO, [11:8] bits
set/clear IO.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/2d802d98fd56d95d764532a33e844d935e0cebb3.1635505900.git.michal.simek@xilinx.com
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
-----BEGIN PGP SIGNATURE-----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=YdSB
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request of efi-next
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
Show the revision of this table as it can be important.
Also update the 'efi table' entry to show the actual address of the EFI
table rather than our table that points to it. This saves a step and the
intermediate table has nothing else in it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present only 4KB of spare space is left in the DTB when building the
EFI app. Increase this to 32KB so there is plenty of space to insert the
binman definition. This cannot be expanded later (as with OF_SEPARATE)
because the ELF image has already been built.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviwed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
If the 'bootm' command is not enabled then this code is not available and
this causes a link error. Fix it.
Note that for the EFI app, there is no indication of missing code. It just
hangs!
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present this is disabled, but it should work so long as the kernel does
not need EFI services. Enable it and add a note about remaining work.
Signed-off-by: Simon Glass <sjg@chromium.org>
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
This converts the following to Kconfig:
CONFIG_88F5182
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_IS_OPENRD_CLIENT
CONFIG_BOARD_IS_OPENRD_ULTIMATE
CONFIG_D2NET_V2
CONFIG_FEROCEON
CONFIG_FEROCEON_88FR131
CONFIG_INETSPACE_V2
CONFIG_KW88F6192
CONFIG_KW88F6281
CONFIG_KW88F6702
CONFIG_NET2BIG_V2
CONFIG_NETSPACE_LITE_V2
CONFIG_NETSPACE_MAX_V2
CONFIG_NETSPACE_MINI_V2
CONFIG_NETSPACE_V2
CONFIG_SHEEVA_88SV131
At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one of two ways. The first way is that it
is defined to a static value, of an unsigned long size. The second way
is that it is defined to something, typically a function, to determine
this value at run time.
However, in a few cases that function returns a static value. Change
that to using the static value directly.
In the case of using something at run time, convert everything to using
a function of the same name and prototype. This will allow for further
cleanups.
Finally, we have a few cases where the function is just not used, so
drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_CLK_FREQ_C100 and CONFIG_SYS_CLK_FREQ_C110 are
only used in one place and not changed by the board config file. Move
these out of the CONFIG namespace and in to the CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Signed-off-by: Tom Rini <trini@konsulko.com>
Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.
For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.
For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a few more tests for BMP rendering. Use a back door into the sandbox
SDL driver to adjust the resolution at runtime.
The truetype code does not support 8bpp. Add this so that the display is
not blank when running in this mode.
Signed-off-by: Simon Glass <sjg@chromium.org>
When unit tests are run they currently create a new window. Update the
code so that the old one is removed first. This avoids the confusion as to
which one is active.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox only supports 16 and 32bpp depths, since those are the
easy ones with SDL.
We can support other depths by manually converting the pixel formats. Add
support for this, to enable an 8ppp (monochrome) format.
Signed-off-by: Simon Glass <sjg@chromium.org>
The USB controller index must be separated from the type argument,
otherwise the preboot command fails with the error:
Error: Wrong USB controller index format
Add the missing space to fix fastboot mode here.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
10.1" OF is a capacitive touch 10.1" Open Frame panel solutions.
PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged
10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the px30 devicetree files from linux-next tree.
commit <14ce8069f48b> ("lib/stackdepot: allow optional init and
stack_table allocation by kvmalloc() - fixup3")
Note, this path even sync rk3326 files as it depends on px30.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
dmc node is specific to U-Boot, it is always better practice
to maintain U-Boot specific nodes into -u-boot.dtsi files
in order to maintain Linux dts file sync compatibility.
Move the dmc into px30-u-boot.dtsi, also add dmc node
explicitly in rk3326-odroid-go2-u-boot.dtsi since it is
using px30.dts.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
adapting commit ac804143cf ("mmc: rockchip_sdhci: add phy and clock
config for rk3399") to fix the issue "Not found emmc phy device".
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com> - on a Rock960
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se> - on a Pinebook Pro
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We configured the drive strength and security of EMMC in
arch_cpu_init().
Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable sdhci and sdmmc0 node in rk3568-u-boot.dtsi
Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable SPL support in Kconfig and add some related option in
rk3568_common.h
Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com>
Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Odroid Go Advance has a hardware random number generator present.
The device does not have an upstream Linux driver, but does have a
U-Boot driver. Add the appropriate node so that the hardware RNG can be
used in U-Boot.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use this new Kconfig instead of OF_BOARD, so we know for sure which boards
obtain their devicetree from a prior stage. Leave sandbox alone since it
does not. Also don't touch xilinx_versal_virt since it does not have a
specific TARGET Kconfig.
This option implies OF_BOARD for now, but with future work standard
passage may be used instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add rpi_4_32b and rpi_arm64 to the list of boards converted]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty devicetree file for these boards. It seems to be possible to
obtain a real one from another bootloader called 'bolt' but I will leave
this to the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty file to prevent build errors when building with
CONFIG_OF_SEPARATE enabled.
Unfortunately there are no build instructions in the U-Boot tree to enable
a real file to be created.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
The real devicetree is created by the Xen project on-the-fly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sync these file, obtained from Linux v5.15.
Add a note for the maintainer, and SPDX lines where they are missing.
The added lines are:
SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
Note, this matches the text in those files, but is not the same as the
GPL-2.0 of some files.
[1] https://releases.linaro.org/android/reference-lcr/juno/7.1-17.05/
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Sync these files, obtained from Linux v5.15.
This adds a devicetree file for rpi_4 which was not there before.
Testing shows no change so far as I can see:
- boots to U-Boot prompt on rpi0, rpi2
- boots to distro on rpi3
- boots to distro on rpi4
I am assuming that syncing with Linux is safe, but the maintainer should
know for sure.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Copy the existing empty version of this file, so splitting the existing
qemu-virt into two, since anyone actually trying to use this will need a
different devicetree for 32- and 64-bit machines.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no point to hide/disable fatal errors via debug() macro.
Print fatal errors loudly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Include file debug_uart.h already contains documentation how to use it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a backport from Marvell U-Boot:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell
commit 381d029e7a ("fix: serdes: a38x, a39x: Improve USB3 electrical
configuration")
Improves electrical USB3 receiver jitter tolerance test:
- De-Emphasize force, in functional mode the transmitter should always
have 3.5db de-emphasize, so we are forcing it.
- After forcing De-Emphasize, choose 3.5db (After forcing, default is
6dB so need to change it to 3.5dB).
- Align90 set to 0x58 - this is the sample point in the receiver, after
the clock is recovered this sampler samples at the chosen value, usually
it is supposed to be 0x60(which is the center of the eye), but sometimes
after adding jitter and ISI the center of the eye can move slightly and
the sample point is not necessarily the exact center, and after
optimization (searching the middle of the eye manually) it was seen that
the center of the eye is actually 0x58 and not 0x60.
- FFE Res and FFE Cap set to 0xE & 0xF respectively: improves this
settings is adequate according to how the USB3 spec defines the
interconnect, thus improves USB3 jitter tolerance settings.
- Change the resolution of the DFE to 0x3 which is 6mV(highest
resolution) , this avoids the DFE to saturate and cease to work.
- HPF set to 0x3 which is 5Khz high pass filter, the function of the HPF
is to filter the low frequency patterns(below 5Khz) to make sure that
the signal is not a noise, the setting before was 0x1(205Khz), and the
change came since the USB3 CP0 pattern, that is used in the USB3 jitter
tolerance testing, is similar to PRBS15, which has 2^15=32768bits which
is 32768*200ps (200ps is one Unit interval in USB3(5Gbps)) = 6.5us,
which is in frequency terms: 152Khz. since the PRBS15 is a random
pattern and can theoretically have once in a while a pattern that will
be at frequency of 152Khz, hence the previous setting (205khz HPF) can
possibly filter this pattern which can cause to an error in the
receiver, thus this change to avoid such scenarios.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Signed-off-by: René Straub <rene.straub@netmodule.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The electrical serdes configuration for USB3 expects an array as data
argument. For USB3 the second value is used (see data_arr_idx = USB3 =
1). However, because only one value is inside the array mv_seq_exec is
accessing an invalid element and the serdes is configured wrongly.
This wrong initialization is leading to an unreliable detection
mechanism for some USB3 devices. We were able to reproduce the issue
regularly with an LTE modem from Sierra Wireless (SM7455) where it was
not detected as USB3 device in 1/3 of all tests.
This commit fixes the issue by setting data_arr_idx to 0. This is the
same value as the original U-Boot from Marvell is using. There it is
called FIRST_CELL which is a define for 0.
See: https://github.com/MarvellEmbeddedProcessors/u-boot-marvell
commit 56f963ce4c ("fix: serdes: a38x, a39x: Fix USB3 serdes DB
initialization")
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Signed-off-by: René Straub <rene.straub@netmodule.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Convert A3720 common PHY driver to official DT bindings.
This puts us closer to be able to synchronize A3720 device-trees with
those from Linux.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After all Armada XP boards have been switched over from legacy I2C
support to DM I2C, let's now also convert this serdes code to use
the DM I2C API.
Signed-off-by: Stefan Roese <sr@denx.de>
Add the 'missing-msg' for blobs for more detailed output on missing system
firmware and SEBoot blobs.
Signed-off-by: Ivan Mikhaylov <ivan.mikhaylov@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix minor typos:
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmG8PNIcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyN4NCACbdi5EFjoNkGhCWLIX
SobXNcBGaL9Zpr5qZq77uFqFeFPeiAClk9X+TcSHhBTSWPugzNCdXEdENEGdiiOR
Yxe/QvBL7ZsKkhGBw5W8sb81NBPlpnVY7DWufjYvWq7S3C3bIDahQpCeWHKXDO0H
ZzIX1413kfHRKsAIT+IbufmC1dcWY8SWQEArSkL2KhTQyHnLVGAaholgEGXoKMoC
0ACXO+uhqaAY0/1eWvvYjcfotlz881ROajSRITh+Gu0UuHyRr2Fvj7jZvF5E4Q4f
Cu8iciDsimYSDGLZsOJjPIDTfsx9jbA8IcYIAMxOLW8OYbIL6QAUKsJ2LLKao1q5
SYXP
=YXsB
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.04 cycle:
This feature set includes : support for the new QSPI hardware on
sama7g5, small fixes on sam9x60 and sama7g5, some additions of commands
and PIO controller on sam9x60/sam9x60ek.
Double peripheral RBF configuration are needed on some devices or boards
to stabilize the IO configuration system.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Sin Hui Kho <sin.hui.kho@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
This patch triggers warm reset to recover the MPFE NoC from corruption
due to high frequency transient clock output from HPS EMIF IOPLL at
VCO startup after peripheral RBF is programmed.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Sin Hui Kho <sin.hui.kho@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
The romcode_initswstate register need to be set with FSBL_IMAGE_IS_VALID
value if the current FSBL image is found valid, otherwise BootROM will
look for next subsequent valid FSBL image when warm reset is triggered.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Sin Hui Kho <sin.hui.kho@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
New SoC's of AT91 family with ARM-9 core includes a regular timer and a 64-bit
timer.This patch adds a compile time option to the Makefile such that the old
timer driver is chosen and compiled as default if none of timer configuration
options are explicitly defined in the board configs.
Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
The ethernet PHY must be reset on AV96, however DWMAC currently does
not support the MDIO-bus PHY GPIO reset bindings and the ethernet MAC
PHY reset property is going away on next DT sync. Add PHY specific
reset bindings to trigger the PHY reset and fix sporadic ethernet
malfunctions, until the next DT sync.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The alternate function of PD20 is 4 as per the datasheet of
sama7g5 and not 5 as defined earlier.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
The rzg2_beacon_defconfig creates an image for RZ/G2[MNH] and
as such creates three different device trees and each of them
have a corresponding -u-boot.dtsi file which are basically
copies of each other. Create a common include file to be
referenced by each of the respective board-u-boot.dtsi files
to reduce duplicate code and simplify support going forward.
This also restores some lost functionality from the device
tree re-sync and updates the MAINTAINER file to include all
beacon-renesom device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The device trees for the Beacon RZ/G2[MNH] boards have undergone
some changes over time, so resync them now.
Signed-off-by: Adam Ford <aford173@gmail.com>
UCLASS_EFI_LOADER is used for devices created by applications and
drivers loaded by U-Boots UEFI implementation.
This patch provides a new uclass (UCLASS_EFI_MEDIA) to be used for devices
that provided by a UEFI firmware calling U-Boot as an EFI application.
If the two uclasses can be unified, is left to future redesign.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Commit 03510bf621 ("sunxi: only include alias for eMMC when mmc2
used") protected the eMMC alias in U-Boot's DT stub the with the
associated Kconfig symbol, but was actually using the wrong name.
Fix the name of the symbol to match what's defined in Kconfig and what
the defconfig files actually use.
Fixes: 03510bf621 ("sunxi: only include alias for eMMC when mmc2 used")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: 5kft@5kft.org
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
QSPI0 has a MX66LM1G45G SPI NOR flash connected.
Enable the controller and describe the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
sama7g5 embedds an OSPI and a QSPI controller:
1/ OSPI0 Supporting Up to 200 MHz DDR. Octal, TwinQuad, Hyperflash
and OctaFlash Protocols Supported.
2/ QSPI1 Supporting Up to 90 MHz DDR/133 MHz SDR.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
CONFIG_SYS_ATA_PORT_ADDR is not used in the code anymore. Drop it and use
ATA_PORT_ADDR() locally instead.
Drop CONFIG_IDE_RESET_ROUTINE and CONFIG_IDE_SWAP_IO which are also
unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
When compiled with -Og for better debugability u-boot ends up in a stack
overflow using
gcc (Ubuntu 11.2.0-7ubuntu2) 11.2.0
GNU Binutils for Ubuntu 2.37
putchar(ch) is defined as a macro which ends up calling U-Boot's putc()
implementation instead of the glibc one, which calls os_putc() ...
Let's use fputc(ch, stdout) instead as fputc() does not exist in U-Boot.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable saving environment to SPI flash memory on SiFive
Unmatched.
Signed-off-by: Thomas Skibo <thomas-git@skibo.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Configure SPI flash devices into SPL. Add SPI boot option to spl.c.
Document how to format flash for booting.
Signed-off-by: Thomas Skibo <thomas-git@skibo.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The device tree split into .dtsi and .dts files, common
device node for eMMC/SD, enable I2C1, UART1 for console
instead of UART0, enable the DDR 2GB memory and in
that 288MB memory is reserved for fabric buffer.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM
This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.
Signed-off-by: Tom Rini <trini@konsulko.com>
The support of a predefined DDR PHY tuning result is removed for
STM32MP1 driver because it is not needed at the supported frequency
when built-in calibration is executed.
The calibration parameters were provided in the device tree by the
optional node "st,phy-cal", activated in ddr helper file by the
compilation flag DDR_PHY_CAL_SKIP and filled with values generated
by the CubeMX DDR utilities.
This patch
- updates the binding file to remove "st,phy-cal" support
- updates the device trees and remove the associated defines
- simplifies the STM32MP1 DDR driver and remove the support of
the optional parameter "st,phy-cal"
After this patch, the built-in calibration is always executed
and the calibration registers are moved in the phy dynamic part;
that allows manual tests.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The uSD level translator on DHSOM and Avenger96 are optional, however it
is possible to auto-detect it. This is done by setting SD CMD line high,
and then testing whether signal level on CK line matches the signal level
on CKIN line. If so, the uSD level translator is present, otherwise it is
not populated.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The ethernet PHY must be reset on AV96, however DWMAC currently does
not support the MDIO-bus PHY GPIO reset bindings and the ethernet MAC
PHY reset property is going away on next DT sync. Add PHY specific
reset bindings to trigger the PHY reset and fix sporadic ethernet
malfunctions, until the next DT sync.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
These functions currently lack tests so add some. The error handling
differs betwee livetree and flattree at present, so only check the error
codes with livetree.
Signed-off-by: Simon Glass <sjg@chromium.org>
efi_system_reset() should exit if called with EFI_RESET_SHUTDOWN.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The eth aliases are for correct probing order, so that each Ethernet
port will get a predictable MAC address from the environment.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In case U-Boot enters relocation with GD_FLG_SKIP_RELOC, skip the
relocation. The code still has to set up new_gd pointer and new
stack pointer.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Add and Enable USB SuperSpeed Host Port in SPL.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Return CONFIG_SYS_LOAD_ADDR pointing to DRAM space for
spl_get_load_buffer() to allow generic SPL image loading
code (e.g. FIT and Ymodem) to store data in DRAM.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Add HACE DTS node and enable it for AST2600 EVB.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Add YCLK enable for HACE, the HW hash engine of
ASPEED AST2600 SoCs.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
The AST2600 SRAM has been extended to 88KB since A1
chip revision. This patch updates the SRAM size to
offer more space for early stack/heap use.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Some boards do not enable SPL_SERIAL so cannot use the debug UART. Add
this condition to the code and drop use of the preprocessor while we are
here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
At present we don't init the debug UART in the generic ARM code, but
instead leave it to individual machines to handle. This is not the
way it is supposed to work.
Add the required init to the crt files. This ensures that the UART
is available as early as possible and that the announcement appears
when it should, if enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver supports both pin muxing and GPIO support for the
pin control logic found on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYZPDrwAKCRDKSWXLKUoM
IS9GAJ93T/uprhLcKWMb+284YMb2caWgOACfZ02nTlzvZKNNXVretJgZaHXqj1M=
=cwTL
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
Remove the extra (empty) argument passed to str8w, causing the following
error:
<instantiation>:40:47: error: too many positional arguments
str8w r0, r3, r4, r5, r6, r7, r8, r9, ip, , abort=19f
^
u-boot/arch/arm/lib/memcpy.S:240:5: note: while in macro instantiation
17: forward_copy_shift pull=16 push=16
^
Note: no functional change intended.
Fixes: d8834a1323 ("arm: Use optimized memcpy and memset from linux")
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
The subdivision name "TQ Components" hasn't been in use for a long time.
Rename the vendor directory to "tq", which also matches our Device Tree
vendor prefix.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
This symbol has been functionally dead for a long time. Remove the last
and recent re-introductions of setting it, and update the whitelist so
it will not be re-introduced again.
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 4b2be78ab6 ("time: Fix get_ticks being non-monotonic") has
broken boot on chiliboard platform, as it requires '/chosen/tick-timer'
in device-tree. This resulted in following panic message:
Could not initialize timer (err -19)
Provide missing chosen property in device-tree to fix chiliboard
support.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
We should avoid #ifdef in C modules and the unused functions
are eliminated by the linker.
Use the more readable IS_ENABLE() instead.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In some part of STM32MP15 support the CONFIG_TFABOOT can be replaced
by other config: CONFIG_ARMV7_PSCI and CONFIG_ARM_SMCCC.
This patch also simplifies the code in cpu.c, stm32mp1_ram.c and
clk_stml32mp1.c as execution of U-Boot in sysram (boot without SPL and
without TFA) is not supported: the associated initialization code is
present only in SPL.
This cleanup patch is a preliminary step to support SPL load of OP-TEE
in secure world, with SPL in secure world and U-Boot in no-secure world.
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove the dependency on CONFIG_TFABOOT in stm32mp Kconfig
- always activate the ARCH config: CONFIG_ARCH_SUPPORT_PSCI
and CONFIG_CPU_V7_HAS_NONSEC
- CONFIG_ARMV7_NONSEC is deactivated in trusted defconfig
- the correct sysreset driver is activated in each defconfig:
CONFIG_SYSRESET_PSCI or SYSRESET_SYSCON
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Currently the upper OTP (after 57) are shadowed in U-Boot proper,
when TFABOOT is not used.
This choice cause an issue when U-Boot is not executed after SPL,
so this BSEC initialization is moved in SPL and no more executed in U-Boot,
so it is still executed only one time.
After this patch this BSEC initialization is done in FSBL: SPL or TF-A.
To force this initialization in all the case, the probe of the BSEC
driver is forced in SPL in the arch st32mp function: spl_board_init().
Even if today BSEC driver is already probed in STM32MP15x clock driver
clk_stm32mp1.c because get_cpu_type() is called in
stm32mp1_get_max_opp_freq() function.
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The nWP GPIO hog was used to unlock the SPI NOR write protect when U-Boot
used to operate the SPI NOR in 1-1-1 mode. Now that the SPI NOR is operated
in 1-1-4 mode, the hog has adverse effects and causes transfer corruption,
since the hogged pin is also the IO2 pin. Remove the hogs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The stm32 gpio driver private data are not needed in arch include files,
they are not used by code except for stm32 gpio and pincontrol drivers,
using the same IP; the defines for this IP is moved in a new file
"stm32_gpio_priv.h" in driver/gpio.
This patch avoids to have duplicated file gpio.h for each SOC
in MPU directory mach-stm32mp and in each MCU directory arch-stm32*
and allows to remove CONFIG_GPIO_EXTRA_HEADER for all STM32.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Device tree alignment with Linux kernel v5.15-rc6
- Set {bitclock,frame}-master phandles on ST DKx
- Add coprocessor detach mbox on stm32mp15x-dkx boards
- Add coprocessor detach mbox on stm32mp157c-ed1 board
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use binman to add the stm32image header on SPL binary for basic boot
or on U-Boot binary when it is required, i.e. for TF-A boot without FIP
support, when CONFIG_STM32MP15x_STM32IMAGE is activated.
The "binman" tool is the recommended tool for specific image generation.
This patch allows to suppress the config.mk file and it is a preliminary
step to manage FIT generation with binman.
The init_r parsing of U-Boot device tree to search the binman
information is not required for STM32MP15, so the binman library
can be removed in U-Boot (CONFIG_BINMAN_FDT is deactivated).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The missing trailing newline could confuse check-config.sh if the
definition of an option was on the first line of the next file that
find(1) happened to return.
Signed-off-by: William Grant <wgrant@ubuntu.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Don't use efi_allocate_pages(). The allocated memory isn't carved out of
the lmb allocations. The memory might then be allocated twice.
Particulary, this might happened with the fdt_high/initrd_high feature
which will relocate the fdt/ramdisk. This might then overlap with the
spin table.
Instead use memalign() which allocates on memory on the heap which is
correctly carved out by lmb.
Please note, that the memory is later reserved in the device tree as
well as in the EFI memory map in ft_fixup_cpu() (in
arch/arm/cpu/armv8/fsl-layerscape/fdt.c).
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Instead of looking at all USB (host) devices, just search all DWC3
device tree nodes. This will (1) fix a panic if of_match is zero and (2)
also apply the fixup if the controller is in peripheral mode. Both
happen when the DWC3 USB controller driver is used.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that everything is prepared, copy the fsl-ls1028a.dtsi from the
linux kernel v5.14.12.
Notable changes:
- second watchdog added
- the number of chip selects of the SPI controller is now correct and
reflects what the hardware offers
- the LPUARTs have the correct clock parent
- USB controllers are enabled by default, which was already the case
before this sync because all board enabled all the USB controller
nodes. A linux patch to fix this is pending.
- the eSDHC controller changes from big-endian to little-endian, but
that property seems to be not used at all.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Disable the PCIe controllers by default, just like in the linux device
tree. But there is one catch, for linux they are enabled in-place by the
bootloader. Obviously, this doesn't work for the bootloader. Thus we
explicitly enable the controllers in the -u-boot.dtsi files.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
To make the synchronization of the u-boot device tree with the one from
linux easier, move the I/O window to the one which is specified in the
linux device tree. The actual value shouldn't matter as long as it
mapped to the corresponding memory window of the PCIe controller which
is a 32GiB window at 80_0000_0000h (first controller) or 88_0000_0000h
(second controller).
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This property is unused in the layerscape PCIe controller driver and not
present in the linux device tree. Remove it to be similarly.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official bindind of the PCIe controller of the ls1028a has the
following compatible string:
compatible = "fsl,ls1028a-pcie";
Additionally, the resource names and count are different. Update the
driver to support this binding and change the entry in the ls1028a
device tree.
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-dwc3", "snps,dwc3";
Change the ls1028a device tree and add this new compatible to the fsl
specific xhci driver, otherwise the generic dwc3 driver will be used
with the compatibles above.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The driver will look for a named resource "ecc-addr", but this isn't the
official binding. In fact, the official device tree binding
documentation doesn't mention any resource names at all. But it is safe
to assume that it's the linux ones we have to use if we want to be
compatible with the linux device tree. Thus rename "ecc-addr" to
"sata-ecc" and convert all the users in u-boot.
While at it, also rename "sata-base" to "ahci" although its not used at
all.
This change doesn't affect the SATA controller on the ZynqMP.
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-lpuart";
Add the missing compatible to the driver and update the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official devicetree bindings specifies spi-num-chipselects as the
name. Use it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";
Add the missing compatible to the driver and update the device tree.
We can use the fallback "fsl,ls1021a-v1.0-dspi", because the endianness
is determined by the little-endian property and not by the compatible
string itself. Further, we won't need and specific details on the DMA
configuration (which is different on the LS1021A). If it's ever needed,
we can later add the more specific "fsl,ls1028a-dspi" compatible to the
driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to the linux device tree specification the compatible string
is:
compatible = "arm,sp805", "arm,primecell";
Fix all users in u-boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update the labels of the nodes to match the kernel ones.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
While inserting them into the new location, keep them sorted by the
register base offset just like in the linux kernel device tree.
While at it fix the indentation.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
While inserting it into the new location, keep it sorted by the
register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
While inserting them into the new location, keep them sorted by the
register base offset just like in the linux kernel device tree.
While at it fix the indentation.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
While inserting them into the new location, keep them sorted by the
register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
While inserting them into the new location, keep them sorted by the
register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
While inserting them into the new location, keep them sorted by the
register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
While inserting them into the new location, keep them sorted by the
register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
While inserting them into the new location, keep them sorted by the
register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
While inserting it into the new location, keep it sorted by the
register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
While inserting them into the new location, keep them sorted by the
register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Populate the /soc node with the first device node.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
To keep the device tree similar to the linux kernel one, we need to move
all CCSR related devices into the /soc node. To keep the patches easy to
review, we initially add an empty /soc node and populate it piece by
piece.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Nowadays, both boards boot using the TF-A BL1/BL2 and SPL isn't used at
all. The property is not needed, remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This node is some hodgepodge between the ddr controller node at SoC
offset 0x1080000 and some static memory size of 2GiB. Remove this bogus
node because it doesn't seem to be used at all.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no "fsl,ls1028a-gpu" compatible string. It is solely for the
proprietary driver which will never be open source. Lately, linux gained
support for the open source etnaviv driver for the GPU (although there
is still support for the DisplayPort PHY missing to get actual graphics
output). Thus, instead of supporting some proprietary driver, switch
over to the open source one, which also have an official device tree
binding.
Cc: Andy Tang <andy.tang@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This has not been supported by toolchains for some time and has been
putting out a warning. Drop this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Remove "num-cs" property from device-tree as it is no longer used by
qspi driver anymore.
Also, specify status as "disabled" and enable qspi support in respective
board dts files. This will also help in aligning node properties with
other board properties.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Generate a FIT update image during build. The image will be called
"u-boot.update" and can be used to build an EFI UpdateCapsule or during
DFU mode. Although, the latter isn't supported because there is no USB
OTG driver yet.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Disabling PCIE support currently lead to a crash because the code for
erratum A010315 is still run. Add a conditional to only select
CONFIG_SYS_FSL_ERRATUM_A010315 when CONFIG_PCIE_LAYERSCAPE is enabled.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
to fix following checkpatch warnings.
Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where
possible
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch adds memcpy_fromio and memcpy_toio definitions for some device
drivers which have these definitions, like cadence_qspi_apb.c
Signed-off-by: Wei Fu <wefu@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Provide function sbi_get_impl_version() to retrieve the SBI implementation
version.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This variable is already defined by the EFI code. Drop the duplicate
definition when building a 64-bit EFI app.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Most modern platforms use 64-bit EFI so it is useful to have a U-Boot app
that runs under that. Add a (non-functional) build for this.
Note that --whole-archive causes the gcc 9.2 linker to crash, so disable
this for now. Once this is resolved, things should work.
For now, avoid mentioning the documentation for the 64-bit app, since it
does not work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Most EFI implementations use 64-bit but U-Boot only supports running as
a 32-bit app at present. While efi-x86_payload64 does boot from 64-bit
UEFI it immediately changes back to 32-bit before starting U-Boot.
In order to support a 64-bit U-Boot app, update the Kconfig to add an
option for 32/64 bit. Update the prompt for the existing option so it is
clear it relates to the stub. Move both up to just under the choice that
controls them, since this looks better and the menu.
Use CONFIG_EFI_APP in the Makefile instead of CONFIG_TARGET_EFI_APP,
since the latter is specific to a single target and we will have two.
Memory size is set to 32MB for now so that it can run on qemu without
increasing the default memory size. We may need to increase the default
later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When building a system that has both TPL and SPL_OS_BOOT, code which
tests for CONFIG_SPL_OS_BOOT will be built and enabled in TPL, which is
not correct. While there is no CONFIG_TPL_OS_BOOT symbol at this time
(and likely will not ever be) we can use CONFIG_IS_ENABLED(OS_BOOT) in
these common paths to ensure we only compile these parts in the SPL
case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of hardcoding the watchdog for reset, and the PMIC for poweroff,
use the sysreset framework to manage the available poweroff/reset
backends. This allows (as examples) using the PMIC to do a cold reset,
and using a GPIO to power off H3/H5 boards lacking a PMIC. Furthermore,
it removes the need to hardcode watchdog MMIO addresses, since the
sysreset backends can be discovered using the device tree.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The sysreset uclass unconditionally provides a definition of the
reset_cpu() function. So does the sunxi board code. Fix the build with
SYSRESET enabled by omitting the function from the board code in that
case. The code still needs to be kept around for use in SPL.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- add JetHub D1 eth mac generation with manufacturer OUI
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmGA+fwACgkQd9zb2sjI
SdGGmg/+JNrKt/9yJ5giKwklLMEzSccKG23lQA2bZiYCP3I8j3t6spkHvHRRfgbX
ZJIZjz9zhJ4bvaoiVa64fWoSxx8LpFDnTA1yQugDMxci9djXs2lnq1OdB3t9H4y3
duy4+9U8H0lgpQosZwtLeI2FJvEnkrPlWyUAV9oMoFnyCllfjj0DfGqu9wm7mBlS
q4VMBBVi3z8fhEs/lBoQ0psRHhfqY3ztI7PUCk1j15QSzaEt2RgNFYuVWW9QLi5f
C0PB7/3mh004N6WkjrThT310dKoRNrTA30n4svnZDAtRkeligHe4krJBgJGWy0hk
i6b4Cg1DPWVi5gfsyWsdO4nqJ2SEvmeGJ6EWPkzk3WxvHzVLj0+xBLIEhG+QgLgF
GyoUhsy+crxmEmmE2NXpCnu0hZ+ouldGJXLqC+s/cy1dsXMtBgBfqbz8sfCSP2Qu
w+FqpnwzAFBALB6DoA51Y/yxBwNTs9TtMRnR1kH99Gu7ekcNSZDCuLrrASp1+NiT
axOQFJtopEuPTqBzR7Z/7NV5KjVMhUC9znQEHBmbmIKzr/27go0QF/267E4yEXlS
fi1b0uPGSN+lfSwL2jau/CxRCFJmfTtI6flrkN7dBYWGYc98b1ISxa8U9OnJj/EA
eYywK2BfzL5F2jKVCemJ441riImCZcrnIToWevnWUCLJV07LIcE=
=UyL3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20211102' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- add sm efuse write support and cmd for read/write efuse
- add JetHub D1 eth mac generation with manufacturer OUI
Move error message to the caller of mrfld_pinconfig*() in order
to unify them in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move is_protected assignment closer to its user.
This increases readability and makes maintenance easier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There are two PCB designs in the wild which use the opposite
signaling for SD card detection. This makes U-Boot working
in one case and failing in the other. Quirk this out by
disconnecting SD card detection pin from the PCB by switching
it to mode 3. In the disconnected state the read value is always
the same and inverted to what we are expecting in the code.
BugLink: https://github.com/edison-fw/meta-intel-edison/issues/136
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We would need to quirk out the Card Detect case and for that we allow
configuring the SD/SDIO family of pins.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When building U-Boot with clang, it notices that the i8254.h include
guard does not work correctly due to a typo. Fix it.
Signed-off-by: Alistair Delva <adelva@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed the other same typo at the end of the same file]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Fix a warning seen when compiling this dts file.
Signed-off-by: Alistair Delva <adelva@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is no point to use Method() for the constant.
Replace it with Name() defined object. For the _STA
case it saves 3 bytes per each entry.
Before: 2881
After: 2833
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
patman 'postfix' support
fix binman test race condition causing a timeout error
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmF+8FcRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYP+AgApwZWYteNQu/OKwCFrZq0QIQYZwJQqe93
9CdQtpKH2boakfNcvsbPP5dXk8GNz5cEky1Whk2kIH1b11FHgklnIPFtFxzMesm8
oYET1w0iItp+4P4ZsQmVgJpynz4yUmUnMEOBNqwI2zeo7dMgx8Zw+cWz8FDo4e6K
pDKHAx9UmiCRu6h+IbsAzeMcq/HqAvFOzoWbp/LkmaWnwIjASCM4UUVoz1+UtoFU
0ENn/7vn70WOLw0JoEib8M7qy+IT7Mz42eZwDVGzYKSDlTZmXNwKLLzgJpEqW4hw
lYIEBUK3sr0q+kcKI776JeFaFhI6k71uVJcjkkUgGuF1hda1kc0Msw==
=E8s4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-boo21' of https://source.denx.de/u-boot/custodians/u-boot-dm
Environment tidy-ups
patman 'postfix' support
fix binman test race condition causing a timeout error
# gpg: Signature made Sun 31 Oct 2021 03:36:55 PM EDT
# gpg: using RSA key B25C0022AF86A7CC1655B6277F173A3E9008ADE6
# gpg: issuer "sjg@chromium.org"
# gpg: Good signature from "Simon Glass <sjg@chromium.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B25C 0022 AF86 A7CC 1655 B627 7F17 3A3E 9008 ADE6
Allow usage of the bootstage facilities in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Samsung Galaxy A3, A5, A7 (2017) - middle class Samsung smartphones.
U-boot can be used as chain-loaded bootloader to gain control
on booting vanilla linux(and possibly others) kernels
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Samsung S9 SM-G9600 - Snapdragon SDM845 version of the phone,
for China \ Hong Kong markets.
Has unlockable bootloader, unlike SM-G960U (American market version),
which allows running u-boot as a chain-loaded bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Hi-end qualcomm chip, introduced in late 2017.
Mostly used in flagship phones and tablets of 2018.
Features:
- arm64 arch
- total of 8 Kryo 385 Gold / Silver cores
- Hexagon 685 DSP
- Adreno 630 GPU
Tested only as second-stage bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Allows to change clock frequency of debug uart,
thus supporting wide range of baudrates.
Enable / disable functionality is not implemented yet.
In most use cases of SDM845 (i.e. mobile phones and tablets)
it's not needed, because qualcomm first stage bootloader leaves it
initialized, and on the other hand there's no possibility to
replace signed first stage bootloader with u-boot.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Add preliminary device trees for the Apple M1 mini (2020) and
Apple M1 Macbook Pro 13" (2020). Device tree bindings for
the Apple M1 SoC are still being formalized and these device
trees will be synchronized with the Linux kernel as needed.
The device trees in this commit are based on the initial Apple
M1 device trees from Linux 5.13, nodes for dart, pcie, pinctrl,
pmgr, usb based on bindings on track for inclusion in Linux
5.15 and 5.16 and nodes for i2c, mailbox, nvme, pmu, spmi and
watchdog that don't have a proposed binding yet.
These device trees are provided as a reference only as U-Boot
uses the device tree passed by the m1n1 bootloader.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The DART is an IOMMU that is used on Apple's M1 SoC. This driver
configures the DART such that it operates in bypass mode which is
enough to support DMA for the USB3 ports integrated on the SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Apple M1 SoCs include an S5L UART which is a variant of the S5P
UART. Add support for this variant and enable it by default
on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Apple's M1 SoC that is used in "Apple Silicon"
Macs. This builds a basic U-Boot that can be used as a payload
for the m1n1 boot loader being developed by the Asahi Linux
project.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add MAINTAINERS entry]
Use proper SATA macro for boot_device switch in spl_boot_device() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 2226ca1734 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header")
Stop using the device tree as a source for ad-hoc information.
This reverts commit 2ae7adc659.
Signed-off-by: Michael Walle <michael@walle.cc>
[trini: Also make board/broadcom/bcmns3/ns3.c fail clearly now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Ad-hoc bindings that are not part of the upstream device tree / bindings
are not allowed in-tree. Only bindings that are in-progress with
upstream and then re-synced once agreed upon are.
This reverts commit af288cb291.
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Both Ethernet and USB drivers get their reference clocks from
the versaclock. Enable that driver and the common clock driver
by default.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that TARGET_BEACON_RZG2M can handle all the work that
was done with TARGET_BEACON_RZG2N and TARGET_BEACON_RZG2H,
remove them since they just create more duplicate code.
Signed-off-by: Adam Ford <aford173@gmail.com>
The three different boards share the same board file and only differ
in terms of which SoC is being used. By enabling FIT on
TARGET_BEACON_RZG2M, it can support all three boards and elimate
duplicate code.
Signed-off-by: Adam Ford <aford173@gmail.com>
This adds support for amlogic efuse write and provides two subcommands
of "sm" command: "efuseread" and "efusewrite" to read/write bytes between
memory and efuse.
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
[narmstrong: fixed indent at end of patch]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
- mvebu: Fix usage of BIN header arguments (Pali)
- mvebu: turris_omnia: Fix MTD partitions order for Linux (Pali)
- mvebu: nandpagesize support for kwbimage v1 (Pali)
U-Boot SPL binary does not read BIN header arguments, so passing some dummy
values 0000005b and 00000068 has no effect for U-Boot SPL code.
Probably these two values comes from old Marvell DDR training code which
was separated from U-Boot and used it for some configuration.
Seems that two 32-bit values were specified here to ensure SPL code
alignment to 128-bit boundary as it is required e.g. for A370 or AXP
processors. Main kwbimage header is 64-byte long which is aligned to
128-bit boundary. Optional kwbheader is 32-bit long, number of BIN header
arguments is stored in 32-bit number. So for alignment to 128-bit boundary
is needed 64-bit padding which exactly these two 32-bit dummy arguments
provided.
Now when mkimage correctly aligns start of executable code in BIN header to
128-bit boundary, there is no requirement to put dummy argument values into
kwbimage. So remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Important detail is availability of kwbimage BIN header arguments passed
via r0 and r1 registers by BootROM.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
OF_HOSTFILE is used on sandbox configs only. Although it's pretty
unique and not causing any confusions, we are better of having simpler
config options for the DTB.
So let's replace that with the existing OF_BOARD. U-Boot would then
have only three config options for the DTB origin.
- OF_SEPARATE, build separately from U-Boot
- OF_BOARD, board specific way of providing the DTB
- OF_EMBED embedded in the u-boot binary(should not be used in production
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure to (if applicable) flush the D-cache, invalidate I-cache,
and disable MMU and caches before jumping to OPTEE.
This fixes the SDP->SPL->OPTEE boot flow on iMX6Q and most likely on
some other ARM SoCs.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
- Add and enable watchdog driver
- Prepare for SYSRESET driven AXP poweroff
- Prepare for SoCs without MMC2
- Some fixes for extending SPL (SPL-DM for RISC-V)
- Some preparations for proper VBUS management
- Fix secure monitor move
Some Allwinner SoCs (e.g. R329) doesn't have a MMC2 controller at all,
and on boards that we do not utilize MMC2, the alias for it is just
useless.
Only include the alias when we specify CONFIG_MMC_SUNXI_EXTRA_SLOT to 2.
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For some reason, the watchdog was disabled in the H616 device tree. Most
likely this is a copy-paste from the H6 device tree: the H6 watchdog is
disabled because it is broken in some chips. However, there is no
evidence of issues with the H616 watchdog.
Enable the watchdog node so it can be used by the driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
A watchdog helps recover from hangs or failure to boot an OS. It can
also be used by the sysreset framework to intentionally reset the
system. Now that a driver is available, let's enable this functionality
on sunxi boards.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The more recent Allwinner SoCs BootROMs can actually load SPL images
larger than 32KB. We use this on the H616 to fit the extra code needed
for the PMIC into the image, and have provisions in board.c to respect
that larger SPL size when booting from MMC.
However the sunxi SPL SPI loader has a hardcoded load offset of 32KB,
which will fail on the H616.
To fix this, use the same algorithm we use for MMC: if the SPL size is
smaller than 32KB, we use 32KB, otherwise we expect the U-Boot payload
directly after the SPL code.
This prepares for SPI booting with larger SPLs like on the H616.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
sunxi-common.h defines CONFIG_SPL_BSS_START_ADDR to put SPL's BSS in
DRAM. Due to this, we must select SPL_SEPARATE_BSS, or else SPL will
attempt to load its DTB from the wrong address (after BSS in DRAM).
This change fixes booting with SPL_OF_CONTROL=y.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Get Unique ID of SoC iMX7ULP, using the logic described in Fusemap
(IMX7ULPRMB2_Rev0_Fusemap) attached in the i.MX 7ULP APRM [1].
[1]
https://www.nxp.com/docs/en/reference-manual/IMX7ULPRMB2.pdf
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Since SPL has initialized clocks for bus and core. We don't need to
set the default clocks for clock controller node.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Tested-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP EVK has two ethernet ports. Add relevant nodes and properties
for EQoS port to the EVK DTS file.
In -u-boot.dtsi, change the u-boot eqos compatible string, add PHY
reset gpio and remove assigned clocks as not supported in CCF.
Signed-off-by: Ye Li <ye.li@nxp.com>
i.MX8MP has two ENET controllers, have to update the function to
enable loading two MAC addresses.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
There is no need to use zynqmp name as SYS_BOARD for all boards.
The patch is adding an option to change it.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Link: https://lore.kernel.org/r/20211020152518.3511912-1-liambeguin@gmail.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When boot.bin is configured for secure boot the CSU will disable the
JTAG interface on all cases.
Some boards might rely on this interface for flashing to QSPI in which
case those systems might end up bricked during development.
This commit will restore the interface under CSU control
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Link: https://lore.kernel.org/r/20211013134800.19452-1-jorge@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We can only select SPL_SKIP_LOWLEVEL_INIT if SPL is enabled, otherwise
we get a warning about unmet dependencies on platforms that don't use
SPL.
Fixes: cf47a8cf8f ("arm: mvebu: Select SPL_SKIP_LOWLEVEL_INIT on ARMADA_32BIT")
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Instead of declaring CONFIG_SPL_DRIVERS_MISC in board config header,
select it in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Instead of declaring CONFIG_SYS_MALLOC_SIMPLE dependant on
CONFIG_SPL_BUILD in board config header, select
CONFIG_SPL_SYS_MALLOC_SIMPLE in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
It is useful to see some basic EFI info with the command as it forms part
of the information about a board.
Add a hook for this and show the table address as a start.
While here, fix an invalid cast in setup_efi_info(). Note that this
function is using a data structure defined by Linux so we cannot change
it. Also note that ulong is used since this is the standard in U-Boot
(>6k uses), despite there being quite a bit of the more verbose uintptr_t
(930 uses).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The setup routines are called from zimage but don't really belong in the
zimage header. Add a new EFI header to house these. Add comments so it is
clear what the functions do.
Note that these functions are x86-specific. The zimage business is not
used on other architectures.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present this information is stripped when linking. It is useful to keep
it around. Strip it from the .efi files instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add code to build the eMMC variant of the Colibri iMX6ULL, i.e. the
'Colibri iMX6ULL 1GB' which has a eMMC instead of the raw NAND used
on other SKUs.
Related-to: ELB-4056, ELB-4057
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
After the conversion to binman in commit 8996e6b7c6 ("imx8mm_evk: switch
to use binman to pack images"), it is necessary to flash both flash.bin and
u-boot.itb to get a bootable system. Prior to this commit, only flash.bin
was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single
bootable binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone
(for example, for secure boot purposes).
Also update imx8mm_evk.rst to remove the u-boot.itb copy step.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Finally, found the root cause of the issue already once mentioned back
here [2] which caused the following error message during boot:
imx_wdt watchdog@30280000:
pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
Turns out while the watchdog node itself was already u-boot,dm-spl its
pinctrl node was not which caused it to be unavailable at that early
stage. Note that any and all other boards I checked also seem to be
missing this. However, I can't judge whether or not they might indeed
need a similar fix or not.
[2] https://marc.info/?l=u-boot&m=161786572422973
Fixes: commit d304e7ace3
("ARM: imx8m: Fix reset in SPL on Toradex iMX8MM Verdin")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This powers some peripherals on the carrier board e.g. the USB hub.
Related-to: ELB-3206
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Prepare for DEK blob encapsulation support through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application
call. U-boot sends and receives the DEK and the DEK blob binaries
through OP-TEE dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Taken from NXP's commit 56d2050f40 ("imx8m: Add DEK blob encapsulation
for imx8m").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
io read/write may cause wrong result because they may read/write data
from/to register instead of memory. Add 'volatile' to avoid it.
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At some point back in 2018 prior_stage_fdt_address and OF_PRIOR_STAGE got
introduced, in order to support a DTB handed over by an earlier stage boo
loader. However we have another option in the Kconfig (OF_BOARD) which has
identical semantics.
So let's remove the option in an effort to simplify U-Boot's config and DTB
management, and use OF_BOARD instead.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
At some point back in 2018 prior_stage_fdt_address and OF_PRIOR_STAGE got
introduced, in order to support a DTB handed over by an earlier stage boo
loader. However we have another option in the Kconfig (OF_BOARD) which has
identical semantics.
On RISC-V some of the boards pick up the DTB from a1 and copy it in their
private gd_t. Apart from that they copy it to prior_stage_fdt_address, if
the Kconfig option is selected, which is unnecessary.
So let's switch the config option for those boards to OF_BOARD and define
the required board_fdt_blob_setup() for them.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
On mvebu this is defined if and only if !ARM64.
Otherwise it is defined for boards with ARCH_MX23, ARCH_TEGRA and
ARCH_ZYNQ, and also for SOC_AR934X (tplink_wdr4300).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
In preparation for moving this option to Kconfig, rename it to be
consistent with other USB EHCI Kconfig options.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
fix up ppll init freq.
support tclk_emmc.
add freq (26M) for mmc device.
fix up the sfc clk rate unit error.
Change in V2:
remove change id.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The devicetree submitted and approved for the mainline linux kernel is
slightly different than the one present here. This syncs both
devicetrees (for the Rockchip SFC node at least) present on the PX30
and the Odroid Go Advance. Changes include renaming the flash node,
reordering the values in the SFC node for the rk3326-odroid-go2,
changing the name of the cs pinctrl node to cs0, and updating the
u-boot specific tree to utilize the new flash node value.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Starting with commit 92f1e9a4b3 ("clk: Detect failure to set
defaults") the clk driver for the PX30 would fail to probe for the
Odroid Go Advance. This patch is to remove the clock for the GPU from
the U-Boot specific devicetree, as that clock is not supported by the
U-Boot clk_px30 driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove some config finishing by _ badly added by
scripts/build-whitelist.sh when joker is used in comments.
for example:
doc/uImage.FIT/command_syntax_extensions.txt:
... #ifdef CONFIG_OF_* | ...
cmd/nvedit.c:# error Define one of CONFIG_ENV_IS_IN_{EEPROM| \
FLASH|MMC|FAT|EXT4|\
Remove also configs only used in comments:
- CONFIG_BOOGER in include/linux/kconfig.h
- CONFIG_COMMANDS
- CONFIG_INIT_IGNORE_ERROR
- CONFIG_REG_*
- CONFIG_HOTPLUG : drivers/watchdog/omap_wdt.c:18
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
If multiple entries are present in the memory-region property, this new
memory-region-names property can be used to specify names for each of
them so that they can be more easily distinguished.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rather than duplicate the Ethernet MAC address and carveout updating
code for each board, move it to a common location and make it more
reusable.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reserved memory nodes can have additional flags. Support reading and
writing these flags to ensure that reserved memory nodes can be properly
parsed and emitted.
This converts support for the existing "no-map" flag to avoid extending
the argument list for fdtdec_add_reserved_memory() to excessive length.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reserved memory nodes can have a compatible string list to identify the
type of reserved memory that they represent. Support specifying an
optional compatible string list when creating these nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmFlgsIcHHBhdHJpY2Uu
Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/plnND/4q9HSlvddybIPjBHlW
rXz1ISwj8JZPp7R4MJcB4RiHofYZzjTXx3dDYUif6oQMpCDp64KPfcUDW0kaq8U7
ZFwJvt59boV1XWlonIXMb3gAkY6gFa5PnYAE/YXEqKvPPvUb7FkT7BWxm4LxCGsj
mEmboR8u87s6e4ZP03HJsSVa5FnNwJUZU8b+58Vxp10YC0PPf7kpmgCucDhrghvY
TORlk259KUFoZXz4J4My0VzDdxE05gDqq1m6Xw1CzqcUbGysMvjNEHlxGdYbWD/U
maamP19DUmKUREmpj3kO/JZvacLJlQP/mdGJ0OWKNbIr/3ha4dYagxDoRodEVo0m
DYaaVPGvG24G78d5meB2q9wT0aGdTyaqm+XRBQMvMN2LlaGmu9duA1t6yBuyMcFk
BeA7d0eHMo1ezD9FFZMxwIOAWhJlcYQEAMFhUwkR1B322w0NU4nbl9KRCGuGV2Zp
ZFQV4BoMvb0NwAdo66xwZ+gSq4Wp1y46VM6x2Mw52v2F4p3teeAqR906TdQVYO8+
hlYChO9+qK4JO7LPX/5wQ4FIzcq1HnTzTpuOSf28hsemiPMu0OkAQv1J7DohNZix
wELBA+ZIjGXksmDTPjpXg5CSvVALa/l2G816hp7/XTJ1XRBSz/pzjhp5rwm42zmw
x7EPnwzpAlQCSqTQ0sgO+fgoRA==
=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFlfXAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyHzuB/4pV2iAeFBjNf6YYsuk
uvBQm7+j+AQzy0J337bDwulvw8wTKKlaid4qfOpEjW316DI9oXN1bXTlwNsjtQvO
zTILW7MoBjDRhZHsSkeSfIuD+Sc80juAoLBv+GXskQdZOTQUbWdmi2o60gdY5Ba4
WN0i4zOGVqd7xoDuDgM3XC1M2RnKerxDeVt20Ji+5dFfmes11m7br6sWj2j/45f+
q3G1ufHl+ea+8oRLZGjn2ddKCb1wLLOrNZA+74dsZ5SN0LCN0vFsE3+JAk4RZ2A5
omiHVApjE+J3vAjwiVY7apjcIdVEeyb5AioiXSBAEZiq1l1UI7eKDQT75bDkaKSs
4wBV
=78ME
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.01-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.01 cycle:
This small feature set adds the support for PWM driver for the sama5d2
SoC. It also adds a node in the DT for this SoC.
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
Now that the last users of legacy I2C (outside of SPL) have been
resolved, we can enable DM_I2C at the sunxi architecture level.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).
Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.
This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The pmic_bus functions are used in both SPL (for regulator setup) and
U-Boot proper (for regulator setup, SID access, GPIO, and poweroff).
Currently, pmic_bus conflicts with DM_I2C because it uses the legacy I2C
interface. This commit makes pmic_bus dual-compatible with either the
legacy I2C functions or the newly-added PMIC_AXP driver (which uses
DM_I2C). In turn, this allows platforms to start transitioning to DM_I2C
in U-Boot proper, without breaking boards that still depend on the
legacy I2C interface for other reasons.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Instead of using the SoC symbols to decide the bus type, use whichever
bus driver is actually enabled. This allows collapsing all of the AXP2xx
and AXP8xx variants into one "else" case. It also has the advantage of
falling back to I2C when the other bus drivers are disabled; this works
because all of the PMICs support I2C in addition to other interfaces.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the rsb functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants, so move that to the common header.
There are only a couple of pairs of hardware/runtime addresses used
across all PMIC variants. So far the code expected only the "primary"
pair, but some PMICs like the AXP305 and AXP805 use the secondary pair,
so add support for that to the DM driver as well.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the p2wi functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants. Move that to the common header, so it can be used by
both interface implementations.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
AXP_PMIC_BUS enables communication with a specific AXP PMIC at a
PMIC-dependent I2C/P2WI/RSB bus address. It is automatically selected
as a dependency of the PMIC driver. It should not be selectable by the
user when no PMIC is chosen.
AXP_GPIO uses the pmic_bus functions, and also depends on a specific
PMIC header to pick up register definitions.
Both of these changes have no impact on any existing configs, since
the code does not compile if the dependencies are not met.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
SUN8I_RSB should not be selected by MACH_SUN8I, because the hardware
is not present in half of those SoCs (H3/H5, R40, and V3s). Move the
selection to the SoCs where the hardware actually exists.
As it currently stands, selecting that option also requires using it in
some way, which is not the case for one A80 board. Since we have only
three A80 boards in total, we select it their via their defconfigs.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fixing up Sunchip_CX-A99 build]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
CONFIG_SPL_I2C is the wrong symbol to use here. It is the top-level
Kconfig symbol (not specific to either legacy or DM I2C), whereas the
i2c_init() function is specific to legacy I2C. This change fixes a
build failure when enabling SPL_I2C but not SPL_SYS_I2C_LEGACY.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-by: Andre Przywara <andre.przywara@arm.com>
This fixes the usage of the USB 3.0-capable port under U-Boot as USB
2.0-only port.
Original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Account for the changes done between merge proposal and the final merge.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.
Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the clk_ti_am3_dpll_round_rate() attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.
Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruhl7x RM, SSC is supported only for LCD
and MPU PLLs, but the PRCM_CM_SSC_DELTAMSTEP_DPLL_XXX and
PRCM_CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field
in the PRCM_CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE,
MPU, DDR, PER, DISP, EXTDEV).
Link: https://lore.kernel.org/r/20210606202253.31649-5-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruh73x RM, SSC is supported only for LCD
and MPU PLLs, but the CM_SSC_DELTAMSTEP_DPLL_XXX and
CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field in the
CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE, MPU, DDR,
PER, DISP).
Link: https://lore.kernel.org/r/20210606202253.31649-4-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
This adds support for the NanoPi R1S H5 board.
Allwinner H5 SoC
512MB DDR3 RAM
10/100/1000M Ethernet x 2
RTL8189ETV WiFi 802.11b/g/n
USB 2.0 host port (A)
MicroSD Slot
Reset button
Serial Debug Port
WAN - LAN - SYS LED
The dts file is taken from Linux 5.14 tag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since the beginning, all banks have had space for 32 pins, even when
not all pins were implemented. Let's use a single constant for the GPIO
bank size here, like the GPIO driver is already doing.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
