This function sets the polarity of the PWR signal which is not used on
the opos6uldev board. Remove it.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
On i.MX7ULP B0, the DDR clock target is increased from 320Mhz to 380Mhz.
We update DDR clock relevant settings to approach the target. But since the
limitation on LCDIF pix clock for HDMI output
(refer "mx7ulp_evk: Change APLL and its PFD0 frequencies"), we set DDR
clock to 352.8Mhz (25.2Mhz * 14) by using the clock path:
APLL PFD0 -> DDR CLK -> NIC0 -> NIC1 -> LCDIF clock
To reduce the impact to entire system, the NIC0_DIV and NIC1_DIV are kept,
so the divider 14 is calculated as:
14 = (NIC0_DIV + 1) * (NIC1_DIV + 1) * (LCDIF_PCC_DIV + 1)
NIC0_DIV: 1
NIC1_DIV: 0
LCDIF_PCC_DIV: 6
APLL and APLL PFD0 settings:
PFD0 FRAC: 27
APLL MULT: 22
APLL NUM: 1
APLL DENOM: 20
This patch applies the new settings for both DCD and plugin.
There is no DDR script change on this new frequency.
Overnight memtester is passed.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Due to the APLL out glitch issue, the APLLCFG PLLS bit must
be set to select SCG1 APLL PFD for generating system clock to align
with the design.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
To support HDMI display on EVK board, the LCDIF pix clock must be
25.2Mhz. Since the its PCC divider range is from 1-8, the max rate
of LCDIF PCC source clock is 201.6Mhz. This limits the source clock
must from NIC1 bus clock or NIC1 clock, other sources from APLL PFDs
are higher than this max rate.
The NIC1 bus clock and NIC1 clock are from DDRCLK whose parent source
is APLL PFD0, so we must change the APLL PFD0 and have impact to DDRCLK,
NIC1 and NIC1 bus.
Eventually, this requests to set the APLL PFD0 frequency to 302.4Mhz
(25.2 * 12), with settings:
PFD0 FRAC: 32
APLL MULT: 22
APLL NUM: 2
APLL DENOM: 5
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update LPDDR3 script with the changes below:
-Update the precharge command to CMD=01 at the DDR initialization phase
-remove unimplemented registers
Write data bit delay --refer to the DDR_TRIM bits in
IOMUXC1_DDR_SW_PAD_CTL_PAD_DDRn
Test:
One EVK board passes overnight stress test.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For the current APLL setting, as we want the APLL PFD0 to meet DDR clock 320Mhz requirement.
We set MULT to 20, NUM to 4 and DENOM to 2, to get final 22 multiplier. But according to the RM,
the NUM should always be less than the DENOM. So our setting violates the rule.
Actually the ROM has already set the MULT to 22 and leave NUM/DENOM in default value. The calculated APLL PFD0 clock
is 318.9888Mhz, which also meet the DDR requirement.
To fix the issue, we remove the PLL settings in DCD to use default value from ROM, and only set the PFD0 FRAC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since the board uses SPL_OF_CONTROL now, we don't need to
explicitly initialize the MMC driver, but we still need to
pinmux the corresponding pins. This patch removes the
initialization code and leave just the muxing behind.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch enables SiFive SPI and MMC SPI drivers for the
SiFive Unleashed board.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch extends SiFive FU540 board support to setup ethaddr
env variable based on board serialnum read from OTP.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The GEMGXL clock driver is now directly part of Cadence MACB
ethernet driver in upstream Linux kernel. There is no separate
GEMGXL clock driver in upstream Linux kernel hence we drop
GEMGXL clock driver from U-Boot as well.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
libvirt v.5.3.0 with QEMU 4.0.0 or above uses PCI automatically and
thus devices (network, storage, etc) are connected via PCI.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The TI AM654x EVM base board and the associated daughtercards have on-
board I2C-based EEPROMs containing board configuration data. Use the
board detection infrastructure introduced earlier to do the following:
1) Parse the AM654x EVM base board EEPROM and populate items like board
name and MAC addresses into the TI common EEPROM data structure
residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing the associated
presence signals via an I2C-based GPIO expander. Then, if such a
card is found, parse the data such as additional Ethernet MAC
addresses from its on-board EEPROM and populate into U-Boot
accordingly
3) Dynamically create an U-Boot ENV variable called overlay_files
containing a list of daugherboard-specific DTB overlays based on
daughercards found.
This patch adds support for the AM654x base board ("AM6-COMPROCEVM")
as well as for the IDK ("AM6-IDKAPPEVM"), OLDI LCD ("OLDI-LCD1EVM")
PCIe/USB3.0 ("SER-PCIEUSBEVM"), 2 Lane PCIe/USB2.0 ("SER-PCIE2LEVM"),
and general purpuse ("AM6-GPAPPEVM") daughtercards.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM654x EVM based on the TI K3 family of SoCs has an updated board
detection EEPROM structure that contains a TLV record of dedicated MAC
addresses rather than a range of MAC addresses as it was used on earlier
platforms such as DRA7. Add a basic function that allows us setting up
Ethernet MAC addresses into the U-Boot environment based on the MAC
address record contained in the common TI EEPROM structure.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM654x EVM based on the TI K3 family of SoCs have an updated board
detection EEPROM structure, now comprising variable-sized TLV-type
records, containing a superset of what is already being provided on
earlier platforms such as DRA7. Add basic support for parsing the new
data structures contained on the base board into the common TI EEPROM
structure while also providing infrastructure that can be used later on
to parse data from additional EEPROMs such as the ones that are used on
daughtercards for this platform.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add instructions for flashing boot images to the eMMC with a
layout of the address where each image needs to be flashed.
Also add instructions to flash filesystem partition in user
partition and boot kernel from the rootfs.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM654 early initialization sequence. While
at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW
to print diagnostic messages.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
With a recent update to the pinctrl-single driver and the fact
that the da850evm has both DM and OF_CONTROL working in both SPL
and U-Boot, some of the manual pinmuxing can be setup to only
be activated when either the driver doesn't have DM for it, or
when CONFIG_PINMUX isn't available (only during SPL). If the
code ever shrinks enough to support PINCTRL in SPL, a lot of this
can go away. This also remove some manual pinmuxing not needed
by SPL to give SPL a little more breathing room.
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.
The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.
Signed-off-by: David Lechner <david@lechnology.com>
This addresses the following warning message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be
readily adapted. There is some additional 'gpio-hog' support
needed to fully setup USB in a similar manner to Linux.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
This patch solves the following warnings:
warning: no previous prototype for 'board_quiesce_devices' [-Wmissing-prototypes]
void board_quiesce_devices(void)
^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of Trusted boot chain with OP-TEE
- reserved 32MB at the end of the DDR for OP-TEE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
U-Boot activates regulators by reading the "regulator-boot-on"
property in DT; it is requested by M4 early Boot feature.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl0nbDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZcBQgAn+ojgq/hD89bihuhz2oEe6rhzHB9OkcC
sHrVL8Jbmby/BuzISGe4oeeM5yVygBVtUiN/72JiiAHLmykqc4CpRjNvgOOAgKCy
Ml8UyiBNNVNfrD6f9PxAKvPZf6S0gfLnomGOQ/psdEojpY5AvQxQ36D+QFZ0AMP5
67/xjSfN9bNPw8UbgE/VhJ+WFbU948BP2EBt6+NBAtv7HW4AX9vT0famJfWEjwq8
ftmcFOSNGgYcDQ5BwQWX1sFhnwb9XSfurlQsVYBsFA4cx4gj0DfUm1Ugr4wDD+lo
91P+76hSBQ+mHp1HJ90WMd2vAaElG7/SoaicXo9pW6Rc7WIgTjk7gg==
=SdZy
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-9jul19-take2' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
KM Kirkwood boards now implement the driver model for its SPI flash
interface. Therefore, the old board specific claim and release functions
can be deleted. The preprocessor definition CONFIG_SYS_KW_SPI_MPP is yet
unused as well. All its appearances and dependencies are removed in the
kirkwood_spi driver, header files and finally the configuration whitelist.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The corresponding configurations are selected in the common Kconfig file.
This is easier than changing every affected board default configuration
file. The default configuration for the PORTL2 board, however, still needs
some modifications to correctly use the driver model.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
As the SPI NOR and NAND devices share the same hardware pins, the MPP
configuration has to be changed when claiming/releasing the bus. The
current configuration is saved when claiming and restored when releasing.
Furthermore, a general-purpose output is used to switch the chip-select
signal. This is now also implemented for the DM part of the kirkwood_spi
driver.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
As preparation for the upcoming transferring of configurations from header
files to Kconfig, a common Kconfig file for all KM boards was created. For
the moment, it only sources the other three, more specific, Kconfig files.
Therefore, the architecture Kconfig files now include the common Kconfig
file. Also, the configuration selection for KM boards was moved from the
architecture Kconfig files to the board specific Kconfig files.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Rescue mode bootcmd currently only appends the "omniarescue" parameter
to the bootargs variable. We do not want the user to be able to change
rescue mode bootargs. Therefore change this so that bootcmd sets the
bootargs variable in an absolute way (adding console device information
and the omniarescue paramterer).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
We always want to enumerate PCIe devices, because withouth this they
won't work in Linux.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The board code reads MAC addresses from the ATSHA204A cryptochip.
For compatibility reasons the ethernet adapters on this SOC are not
enumerated in register address order. But when Omnia was first
manufactured this was done differently.
Change setting of MAC addresses to conform to the description on the
stickers sticked on actual Omnias.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Document the main U-Boot image offset when booting from SATA disk on the
Clearfog board.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When cross-compiling, sometimes sdl-config must come from a different path
from the default. Add a way to override it, by adding SDL_CONFIG to the
environment before building U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdJEZEAAoJEB6zHgIOrC/I+LAH/jUDQpF5I68h0ZFGm3xoyGhm
3CSv8viOm/kL+GLubjnv4cwAp8N8VRpeJekz0Jt1Xp8C6OIgtnJ2Fln72KD+Z0IC
Rq7ByRS16iq4b6IUDRZObE4Jzxmf7rXU3jr0+/vd/en7kxVlvA9+Gsffs3OTGxC7
z9PysRZPBMH/smIPXdEQxYifnbpDG4fmfGcUWKrYfkB0Kq6Ep98Ia/gXNCY8XJ/A
sbNQGjJWJZWXS/TDetcC2VikssJ+yNFF34uzV+HD5Y3DW6ywLhuoDOz1pg8RR36i
YjcTCQz8lL/UVaUzrGUgPVAC3gdKY6J26GtV3vZavxBcmtGf0FhVtXO/tZc9AsY=
=6G45
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.10 cycle
This includes the Atmel QSPI driver and support for the at91 boards.
This is the port of the driver from Linux, mostly done by Tudor Ambarus.
Add the default config file of QSPI media. The config is based on
sama5d27_som1_ek_mmc_defconfig.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add the default config file of QSPI media. The config is based on
sama5d2_xplained_mmc_defconfig.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- add support for unique generated MAC adresses from SoC serial,
limited to Amlogic GXL/GXM boards for now
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BL1s
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190704' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- fix khadas-vim README
- add support for unique generated MAC adresses from SoC serial,
limited to Amlogic GXL/GXM boards for now
Enable unique MAC address generation for boards usins SoCs having
a known functional and valid unique serial number.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Unlike the BayLibre repos Khadas' repo defaults to using native gcc,
so specify the CROSS_COMPILE setting matching the prescribed toolchain.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
After the conversion to DM the U-Boot proper binary name
is 'u-boot-dtb.img', so adjust it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
After the transition to DM, only the mx6dl/solo wandboard
is supported.
Add FIT image support so that all the wandboard variants
can be supported, like it was prior to the DM conversion.
Successfully booted Linux on mx6q/solo/qp wandboards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdGaVcAAoJEB6zHgIOrC/Ic1oH/3Hu55HbHVnA2QqRof/o6RnZ
VNJQ11+Zs7QA7TIMT/Z5j9ohX0pEkVPQziD9zAL1rz7WJ/laYkPh8wqsKWmfFD2j
2mCCnf8/vGvST8fiSv0BQ6cqozdMwdQjQ08Eqw0srJhCzqj/I8o8MNlts+OAXNIM
CyT7LdIr/QSO05zDYxFibki4qs7Q5S8WXbtjsmbAAYajcet5w5+hEZRAD2YXuUv8
TBuBWz6bgcSLbV7E7YXexoffgIha2K3ETAxWraKZLcc96MNLL054uBraa3dmybqZ
+0+PHIOcNk2JR4BQmUHCoNgEuKTBPlayxZ3hVUzWzUwot4gBRRUFu/pbnRtLcF4=
=RzN7
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2019.07-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2019.07 cycle
Enable DM Video support on iMX53 M53Menlo and fix minor details
to restore previous behavior of the system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block and DM MMC and DM USB support on iMX53 M53Menlo .
Convert board code to match the DM support. This also enables DM
pincontrol to configure the SDHI pins.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM GPIO support on iMX53 M53Menlo and fix up board code where
applicable. Enable MALLOC_F to let the GPIO controllers bind early on.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Joris Offouga <offougajoris@gmail.com>
In case someone detects a PDA and u-boot sets the 'pda' variable,
and the user does a saveenv, the pda is set in env, and if the
screen is removed, u-boot will still have in the env the 'pda'
variable, even if no screen is attached.
In order to fix this, we have to reset the 'pda' variable,
such that it's not just set if the screen is detected, but also unset
if no screen is detected.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The new common rockchip pinctrl driver does not support explicit
requests for a particular pinctrl function. As a result, the
board_init() function bails out early before enabling the boot-on
regulators. Fix this by simply removing the request for pwm0, pwm2
and pwm3. The generic DM code already does the necessary
configuration if necessary.
Reported-by: Levin Du <djw@t-chip.com.cn>
Signed-of-by: Mark Kettenis <kettenis@openbsd.org>
Support common spl_board_init by moving code from puma
board file into, common rk3399-board-spl.c.
Part of the code has sysreset-gpio, regulators_enable_boot_on
but right now only puma board is using this with relevant
config options rest remains common for all targets.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
preloader_console_init is used for printing SPL boot banner that
usually called from spl_board_init.
The current spl_board_init in evb and rock960 is enabling explicit
pinctrl, debug uart prior to calling preloader_console_init which
eventually not required since board_init_f is already enabled
debug uart.
So, drop those explicit enablement calls from spl_board_init of
evb, rock960.
Tested this by enabling CONFIG_SPL_BOARD_INIT and adding
u-boot,dm-pre-reloc property for uart node.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add u-boot.itb BUILD_TARGET for Rockchip platform when SPL_LOAD_FIT
is being used.
This can get rid of building itb explicitly with 'make u-boot.itb'
so, from now all required images will build just by make.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Right now puma rk3399 board need to copy bl31-rk3399.bin and
rk3399m0.bin into u-boot source directory to make use of building
u-boot.itb.
So, add environment variable
- BL31 for bl31.bin (instead of bl31-rk3399.bin to compatible with other
platform BL31 env)
- PMUM0 for rk3399m0.bin
If the builds are not exporting BL31, PMUM0 env, the fit_spl_atf.sh will
notify with warning about which document to refer for more information
like this:
WARNING: BL31 file bl31.bin NOT found, resulting binary is non-functional
Please read Building section in doc/README.rockchip
WARNING: PMUM0 file rk3399m0.bin NOT found, resulting binary is non-functional
Please read Building section in doc/README.rockchip
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK64 is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.
This series allow building u-boot SPL and u-boot.itb for Rock64
board. The proprietary TPL is stil required for deploy:
./tools/mkimage -n rk3328 -T rksd \
-d ./rkbin/bin/rk33/rk3328_ddr_333MHz_v1.16.bin idbloader.img
cat ./spl/u-boot-spl.bin >> idbloader.img
dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
Misspelling of SPDX-License-Identifier is rather fatal than other
general typos, so must be fixed.
This file spells SPDX-Licence-Identifier.
^
I also moved it to the very top of the file with // comment style.
Detected by grepping the source tree:
$ git grep --not -e SPDX-License-Identifier --and -e SPDX-
board/armltd/vexpress64/pcie.c: * SPDX-Licence-Identifier: GPL-2.0+
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Extra "not DM" controllers support is disabled.
u-boot BSP still good enough to upgrade and run images.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Compile the legacy PCIe initialization reoutines only when DM_PCI
is not enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
- LS1046AFRWY support
- USB errata fix and secure boot defconfig support for LS1028A
- Enabled SDHC and SATA for LX2160
- LS1046A serdes fixes
- other minor fixes
Uboot prompt must not be available while running
secure boot. TO ensure this bootdelay must be set
to -2.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
fsl-mc lazyapply command applies dpl from efi_exit_boot_services().
Status of fsl-mc node in working fdt is updated at this stage.
However, an efi application like grub may already have copied the fdt.
So the updates to fdt done at efi_exit_boot_services() may not be
visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply
command is used.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
when compiling dts file using DTC_FLAG='-@', the device tree compiler
reports these warnings:
Warning (alias_paths): /aliases: aliases property name must include
only lowercase and '-'
Fixed the node aliases to silence these warnings.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Change my email address, too many mails
gets to my private mail, created specific email
account just for developmement.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Now that various SPI related options depend on CONFIG_DEPRECATED, in
order for platforms to build out of the box they need to disable various
other options.
Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Marek Vasut <marex@denx.de>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Per discussion on the list, drop this board again.
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2C9f
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot
- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
Staticize 'spl_dram_init' and 'i2c_pad_info1' to fix the
following sparse warnings:
board/freescale/imx8mq_evk/spl.c:30:6: warning: symbol 'spl_dram_init' was not declared. Should it be static?
board/freescale/imx8mq_evk/spl.c:41:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Enable DM GPIO support on iMX6SX VINING|2000 and fix up
board code where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block and DM MMC support on iMX6SX VINING|2000 .
Convert board code to match the DM support. This disables
USB mass storage support due to missing DM USB, however
that will be re-enabled in subsequent patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
After the conversion to DM there is no need to have mmc initialization
code inside U-Boot proper.
Remove the unneeded code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT
V1.0B module. Unlike the V1.0A early access samples exclusively booting
from SD card, they are now strapped to boot from eFuses which are
factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Gigabit Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QM as of yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
pico-dwarf-imx6ul_defconfig does not have an entry in MAINTAINERS file,
so add it to avoid a build warning.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Enable DM Video support on iMX6Q Novena and fix minor details
to restore previous behavior of the system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Enable DM block, DM MMC and DM SATA support on iMX6Q Novena
convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Enable DM GPIO support on iMX6Q Novena and fix up board code
where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
If PMIC is not probed successfully, it is still OK to boot
with default configuration although power is not optimized.
Default voltage of SW1A/SW1B is 1.1V/1.0V for PC32PF3000A1EP
on pico according to table 42 of spec of PF3000 ver 9.0.
Default mode of SW1A/SW1B is APS as expected(table 47).
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Subtracts CONFIG_OPTEE_TZDRAM_SIZE from the available DRAM size so that
the OPTEE memory is not override during u-boot relocation.
Note the OPTEE live in the end part of DRAM and OPTEE boot process will
itself subtract the DRAM region it lives in from the memory map passed
to Linux.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The spl.c source was entirely conditioned by CONFIG_SPL_BUILD.
Change this moving CONFIG_SPL_BUILD to be used in the Makefile,
which is slightly cleaner and more readable.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Enable DM SPI and SF support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM SATA support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block and DM MMC support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM GPIO support on DHCOM iMX6 PDK2 and fix up board code
where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Drop the ad-hoc AHCI binding code, this is superseded by
CONFIG_DWC_AHSATA_AHCI=y resp. drivers/ata/dwc_ahsata.c
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The board file uses the processor type to determine what dtb file
is set. Unfortunately, if the user wants to manually set this,
it get gets overwritten upon boot. This patch adds a check to
see if the value is already set and only changes it if the value
is empty.
Signed-off-by: Adam Ford <aford173@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJc+lyDAAoJEB6zHgIOrC/I2MQH/A20fKVWQcnvmwwuJ8w/QNZ5
syNqpRLgw8jIMuLgmnUOQmjhKEsdcNWlESQt+eppTH2yMTSwNlQVT8SVE2s1podP
QKBSHw4V5UXlYZwZBhrrmL3twVOf6oecoE4gzpnh1ydMHiC1zcHAJuutlNw8y+ye
IVrojVPu5miN91TJuvkcGdafNdFVO4mBMhGhCFA4VN38OI6Dk/fQg4QBrxj/3XWb
+EOznxL1YZYGf8hhYqe68vMVVVT5sSq1SbId6JGHRkAYDcn/qKOuOkzW7FP7tbi/
PidcTmfqOFH1EYnincxQ1cXyhaSs/VOxRHIWgzlRIJJHHp0o7Y+FUGAilSGKHso=
=tnXy
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel fixes for 2019.07 cycle
The bulk of these changes are an effort to unify Tegra186 builds with
builds of prior 64-bit Tegra generations. On top of that there are
various improvements that allow data (such as the MAC address and boot
arguments) to be passed through from early firmware to the kernel on
boot.
Called to configure Ethernet PHY interface selection and
configure clock selection in RCC Ethernet clock tree.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Add 2 new checks:
- detect when USB TYPE-C cable is not plugged correctly.
In this case, GND and VBUS pins are connected but not CC1
and CC2 pins.
- detect is an USB Type-C charger supplies more than 3 Amps
which is not compliant with the USB Type-C specification
In these 2 situations, stop the boot process and let red led
blinks forever.
V cc1 | V cc2 | power supply | red led | console message
range (Volts) |range (Volts)| (Amps) | blinks |
--------------|-------------|--------------|---------|-----------------------------------
> 2.15 | < 0.2 | > 3 | for ever| USB TYPE-C charger not compliant with specification
[2.15 - 1.23[ | < 0.2 | 3 | NO | NO
[1.23 - 0.66[ | < 0.2 | 1.5 | 3 times | WARNING 1.5A power supply detected
[0.66 - 0] | < 0.2 | 0.5 | 2 times | WARNING 500mA power supply detected
< 0.2 | < 0.2 | | for ever| ERROR USB TYPE-C connection in unattached mode
> 0.2 | > 0.2 | | for ever| ERROR USB TYPE-C connection in unattached mode
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update env_get_location() to be able to save environment into
NOR (SPI_FLASH).
Series-cc: pde, cke, pch, uboot-stm32
Cover-letter:
Add saveenv support for STM32MP1
This series adds saveenv support for STM32MP1 on several boot
devices. STM32MP1 is able to boot on eMMC, sdcard and NOR
(NAND support is not fully supported).
On eMMC and sdcard, environment is saved in EXT4 partition
On NOR, environment is saved in a dedicated partition
On NAND, environment is saved in a UBI volume.
This series:
- enables NAND and NOR support on ev1 board
- enables ENV_IS_IN_SPI_FLASH, ENV_IS_IN_UBI, ENV_IS_IN_EXT4
flags
- fixes get_mtdparts()
- allows to override interface, device and partition for ext4
environment
- updates rule to set ENV_IS_NOWHERE value
- introduce ENV_IS_IN_DEVICE
END
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In case of several environment location support, env_get_location
is needed to select the correct location depending of the boot
device .
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This allows to :
- select the current device to save the environment file
- select the correct EXT4 boot device instance
and partition to save the environment file.
For EXT4, device is mmc, device instance is 0 for sdcard or 1 for eMMC.
The partition is set to "auto" to select the first partition with
bootable flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch configure the default value for mtdids and mtparts
dynamically according the presence of nor and nand in
the board device tree
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add support for Avenger96 board from Arrow Electronics based on STM32MP157
MPU. This board is one of the Consumer Edition (CE) boards of the 96Boards
family and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
If early firmware initialized the display hardware and the display
controllers are scanning out a framebuffer (e.g. a splash screen), make
sure to pass information about the memory location of that framebuffer
to the kernel before booting to avoid the kernel from using that memory
for the buddy allocator.
This same mechanism can also be used in the kernel to set up early SMMU
mappings and avoid SMMU faults caused by the display controller reading
from memory for which it has no mapping.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
If early firmware initialized the display hardware and the display
controllers are scanning out a framebuffer (e.g. a splash screen), make
sure to pass information about the memory location of that framebuffer
to the kernel before booting to avoid the kernel from using that memory
for the buddy allocator.
This same mechanism can also be used in the kernel to set up early SMMU
mappings and avoid SMMU faults caused by the display controller reading
from memory for which it has no mapping.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass the ethernet MAC address to the kernel upon boot. This passes both
the local-mac-address property (as passed to U-Boot from cboot) and the
currently set MAC address via the mac-address property. The latter will
only be set if it is different from the address that was already passed
via the local-mac-address property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass the ethernet MAC address to the kernel upon boot. This passes both
the local-mac-address property (as passed to U-Boot from cboot) and the
currently set MAC address via the mac-address property. The latter will
only be set if it is different from the address that was already passed
via the local-mac-address property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 build are currently dealt with in very special ways, which is
because Tegra186 is fundamentally different in many respects. It is no
longer necessary to do many of the low-level programming because early
boot firmware will already have taken care of it.
Unfortunately, separating Tegra186 builds from the rest in this way
makes it difficult to share code with prior generations of Tegra. With
all of the low-level programming code behind Kconfig guards, the build
for Tegra186 can again be unified.
As a side-effect, and partial reason for this change, other Tegra SoC
generations can now make use of the code that deals with taking over a
boot from earlier bootloaders. This used to be nvtboot, but has been
replaced by cboot nowadays. Rename the files and functions related to
this to avoid confusion. The implemented protocols are unchanged.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is required for proper operation of the 8-bit data transfers.
This fixes transient errors seen on BeagleBone Black.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The MAC address is located at at the last 64K of SPI Flash, and
it's 6 bytes long. This patch corrects both the length and
starting byte of the MAC address.
Signed-off-by: Adam Ford <aford173@gmail.com>
commit 21af33ed03 ("ARM: davinci: omapl138_lcdk: Enable DM_MMC")
wanted to enable DM_MMC only for U-Boot and not for SPL.
But CONFIG_DM_MMC is defined for SPL build too. Because of this
MMC device was not getting registered for SPL causing MMC/SD
boot breakage.
Instead use CONFIG_IS_ENABLED(DM_MMC) which will remain false until
CONFIG_SPL_DM_MMC is defined.
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
This patch adds Microchip MPFS Icicle board support.
For now, NS16550 serial driver is only enabled.
The Microchip MPFS Icicle defconfig by default builds
U-Boot for M-Mode with SMP support.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Since we have added the PCI support to the 'virt' target, enable
e1000 and NVME as alternate network and storage devices for these
virtio based devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Enable the new GEMGXL MGMT driver so that GEM 10/100 Mbps works now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
- some fix for rk3399-puma;
- rockchip script make_fit_atf.py cleanup
- Enable TPL for rk3399 orangepi and nanopi4;
- add support for rk3399 boards: Nanopi NEO4, Rockpro64, Rock PI 4;
Add initial support for Rock PI 4 board.
Specification
- Rockchip RK3399
- LPDDR4
- eMMC
- SD card slot
- RTL8211E 1Gbps
- HDMI In/Out, DP, MIPI DSI/CSI
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type
Commit details of rk3399-rock-pi-4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: add ROCK Pi 4 DTS support"
(sha1: 1b5715c602fda7b812af0e190eddcce2812e5417)
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add initial support for Rockpro64 board.
Specification
- Rockchip RK3399
- 2/4GB Dual-Channel LPDDR3
- SD card slot
- eMMC socket
- 128Mb SPI Flash
- Gigabit ethernet
- PCIe 4X slot
- WiFI/BT module socket
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-rockpro64.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: rockpro64 dts add usb regulator"
(sha1: 6db644c79c8d45d73b56bc389aebd85fc3679beb)
'Akash' has sent an initial patch before, so I keep him as board
maintainer and I'm co-maintainer based on our conversation.
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Puma SoMs have a 4 MB SPI NOR flash.
Therefore we can move the environment to the end of the flash
(4 MiB - 16 kiB) in order to not overlap with SPL.
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For bcm7445 and bcm7260, this patch enables CONFIG_DM_MMC and updates
the bcmstb SDHCI driver to use the new driver model. This allows
removal of SDHCI configuration handling from bcmstb.c, and eliminates
a board removal compile warning.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
Add a short note about how to boot U-Boot on Nyan-big using tegrarcm.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The first clock type appears to have and incorrect setting for out of the
mux outputs. It should be CLK_M, not OSC. Fix it and its only user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Manage power supply configuration for board using stpmic1
with LPDDR2 or with LPDDR3:
+ VDD_DDR1 = 1.8V with BUCK3 (bypass if possible)
+ VDD_DDR2 = 1.2V with BUCK2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Pull DRAM layout configuration code into rcar-common.c instead of
having it in multiple copies across board files. This poses no
change for Salvator-X/XS, ULCB and Ebisu boards, however it adds
a bit of extra code for Draak and Eagle boards, which now gain
the capability of being passed in the DRAM layout by the ATF.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Build an SPL which can be started via SCIF download mode on R-Car Gen3
and allows loading and executing U-Boot uImage with the next stage code.
This is also useful for starting e.g. ATF BL2, which inits the hardware
and returns to the U-Boot SPL, which can then load e.g. U-Boot proper.
The H3, M3-W, M3-N SoCs have plenty of SRAM for storing the U-Boot SPL
while the payload, e.g. ATF BL2, executes, so there is no problem here.
However, E3 and D3 have much less SRAM, hence the loader uses a trick
where it copies itself beyond the area used by BL2 and executes from
there. That area is 32kiB large and not enough to hold U-Boot SPL, BSS,
stack and malloc area, so the later two are placed at +0x4000 offset
from start of SRAM, another area not used by ATF BL2. To make things
even more complicated, the SCIF loader cannot load to the upper 32kiB
of the SRAM directly, hence the copying approach.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXOK5Sw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXBvoAJ96YrInVKKWtuVigA9lNpk5xbmbeQCdG9wML4LI
dBbQyzD3mNqvnDMyNPQ=
=Plt7
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.07-rc3' of git://git.denx.de/u-boot-video
- update for using splashfile instead of location->name
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
The gdsys gazerbeam board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 2x 10/100 Mbit/s Ethernet (optional)
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Replace the boolean parameter of io_check_status that controls whether
the status is printed or not with a documenting enum.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
More recent versions of IHS FPGAs feature a different memory layout.
Add a Kconfig option to differentiate between the legacy layout, and the
new layout (which is used on the upcoming "Gazerbeam" and later boards).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Future gdsys boards will switch from the legacy drivers in board/gdsys/common
to DM-based drivers.
Define a Kconfig option that disables the legacy drivers.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The "manual" RAM configuration should not be used if the DM RAM driver
is active, hence, disable the code if the CONFIG_MPC83XX_SDRAM config
variable is defined.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Move CONFIG_SYS_FPGA0_BASE, CONFIG_SYS_FPGA0_SIZE, CONFIG_SYS_FPGA1_BASE, and
CONFIG_SYS_FPGA1_SIZE to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Since the gpio output status on MPC8xxx cannot be read back, it has to
be buffered locally.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The ppc4xx architecture was removed, and with it several old gdsys 44x
boards, but some "debris" from these purged boards was left over.
This patch removes these remnants (mostly entries in Makefiles, some now
superfluous data structures and some now obsolete config variables from
the whitelist).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The initialization sequence in the newest release notes of the 88e1518
phy omits two commands.
Remove them from the sequence.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
For the DM case, use the proper parameter for the regmap_init_mem call
(which is the ofnode, not the udevice).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Except for one counter example, CONFIG_SYS_LBC_LBCR always has a value
of either 0x00040000 or 0x00000000.
CONFIG_SYS_LBC_MRTPR always has the value 0x20000000.
CONFIG_SYS_LBC_LSDMR_{1,2,4,5} are not set for any mpc83xx board.
CONFIG_SYS_LBC_LSRT is set by one board (to 0x32000000).
To simplify the configuration files, hardcode the setting of these
values for mpc83xx.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_SYS_DDR_SDRAM_BASE is set to the same value as
CONFIG_SYS_SDRAM_BASE on all existing boards. Just use
CONFIG_SYS_SDRAM_BASE instead.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_SYS_DDR_BASE is specific to mpc83xx an is always set to the same
value as CONFIG_SYS_SDRAM_BASE. Just use CONFIG_SYS_SDRAM_BASE instead.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Migrate the BR/OR settings to Kconfig. These must be known at compile
time, so cannot be configured via DT.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
We want to normalize all BR/OR config lines as much as possible.
The TQM834x board uses CONFIG_SYS_OR_TIMING_FLASH in a OR definition,
which we want to remove. But CONFIG_SYS_OR_TIMING_FLASH is also used
outside of the config file.
Replace these usages with the definition of the variable, so we can
remove the variable in the next patch.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The HRCW (hardware reset configuration word) is a constant that must be
hard-coded into the boot loader image. So, it must be available at
compile time, and cannot be migrated to the DT mechanism, but has to be
kept in Kconfig.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
MPC83xx uses CONFIG_83XX_CLKIN instead of CONFIG_SYS_CLK_FREQ to set the
system clock. To migrate the architecture, we can replace
CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ.
To do this
* replace all occurrences of CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ
* set CONFIG_SYS_CLK_FREQ to the old value of CONFIG_83XX_CLKIN in all
MPC83xx config files
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The MPC83xx include files contain some settings of the PCI subsystem.
Migrate these to Kconfig until a proper DM PCI driver exists.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Use the proper CONFIG_TARGET_MPC8349ITX Kconfig option to replace the
CONFIG_MPC8349ITX ad-hoc config option.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Use the proper CONFIG_TARGET_MPC832XEMDS Kconfig option to replace the
CONFIG_MPC832XEMDS ad-hoc config option.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The MPC8349EMDS config file contains config options to enable SDRAM
support. To keep this ability after the Kconfig migration, create a new
MPC8349EMDS_SDRAM board that enables the SDRAM support and remove the
SDRAM support from the original board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
vme8349.h contains two separate boards: The vme8349 itself, and the
caddy2 board. The caddy2 board is chosen by setting certain config
variables. Create a proper config file for the caddy2 board to make
Kconfig migration easier.
Furthermore, simplify the vme8349 and caddy2 configs by keeping only the
options necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
MPC8313ERDB has the option of either enabling NOR or NAND boot in its
config file (by commenting out certain #ifdefs). To keep this ability
after migrating options to Kconfig, we introduce two MPC8313ERDB
configs: one for NOR, and one for NAND.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmeter1, and kmcoge5ne boards also build from the same config
file with #ifdef logic.
Create a separate include config for each board with the #ifdef logic
resolved as needed.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmsupx5, tuge1, kmopti2, and kmtepr2 boards all build from the same
include config file with lots of #ifdef logic.
To ease Kconfig migration, create new config include files for these
boards, and resolve the #ifdef logic as needed.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmtegr1, kmvect1, and suvd3 boards all use the same config include
file with lots of #ifdefs in it.
The Kconfig migation will become easier if we get rid of these #ifdefs
first.
Hence, create distinct config include files for these boards, and unwind
the #ifdef logic in these config files to only include the options
necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
There are several includes in mx53cx9020.c which are not required
anymore.
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
These mmc functions were not used anymore since DM_MMC was introduced.
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Enable DM_VIDEO in config and don't overwrite console so it can be set
from environment
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Switch to DM_GPIO and add gpio_request where necessary.
This is needed for DM_VIDEO and fixes an issue with sd card detection
which was introduced by the combination of these commits:
commit 7a0425dd96 ("mmc: fsl_esdhc: make get_cd work well in dm_mmc_ops")
commit 7e04b4c751 ("dm: arm: imx: migrate cx9020 to CONFIG_DM_MMC")
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
When using DM_I2C the speed value supplied to setup_i2c() is not used,
so this code required CONFIG_SYS_MXC_I2C[12]_SPEED to be defined to
compile, but did not actually use them.
Change this so we no longer need to define an unused macro to compile in
DM_I2C mode. Also make it more clear that they do not control the bus
speed. Otherwise it is quite easy to mistakenly believe they are used
to set the bus speed.
Cc: Heiko Schocher <hs@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Enable the green led on SPL completion.
Red led has no pulldown and it will be lighted by default when the
board starts up.
If the PMIC is not configured to enable LDO2, the leds will not light.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The 2 CAN transceivers have a STBDY pin which must be low in order to
operate.
This pin is tied to PB25.
Set it to 0 in bootstrap.
At a later time, this needs to be controlled by Linux power management
system, or requested by some driver as a gpio and tied to 0 during
CAN link up.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Some periphs on the board need to be reset by holding their reset GPIO down
for a specific time period.
On a warm reset, the periphs are not being reset by any reset pin and may be
in a wrong state.
Reset them in the SPL to make sure we are booting into the correct state
machine of the specific board periphs (KSZ eth switch, USB hub, HSIC eth,
Ethercat)
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Re-add support for Aries Embedded MCV SoM, which is CycloneV based
and the associated MCVEVK and MCVEVP baseboard. The board can boot
from eMMC. Ethernet and USB is supported.
The Aries Embedded boards have been removed with commit 03b54997d5
("board/aries: Remove"). I will now take care of them.
The device-tree files are from mainline Linux commit e93c9c99a629
("Linux v5.1)".
Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de>
CC: Marek Vasut <marex@denx.de>
CC: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Mark Jonas <mark.jonas@de.bosch.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Improvements and new features:
- split more rockchip pinctrl_core feature into per SoC
- enable TPL for evb-rk3399 board
- enable TPL/SPL for evb-px5 board
- enable TPL and OP-TEE support for evb-rk3229
- update fix in arm common assembly start code for rockchip header file
- update default SPL_FIT_GENERATOR for rockchip
- rk3399 boards update to use '-u-boot.dtsi'
- add new rk3399 boards: Nanopi M4, Nanopc T4
- enable sound for chromebook_minnie
Add initial support for Nanopc T4 board.
Specification
- Rockchip RK3399
- Dual-Channel 4GB LPDDR3-1866
- SD card slot
- 16GB eMMC
- RTL8211E 1Gbps
- AP6356S WiFI/BT
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-nanopc-t4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: Add NanoPC-T4 IR receiver"
(sha1: 95658e21b1707ad7844f873db2fdaa295109a5a3)
Tested-by: Daniel Gröber <dxld@darkboxed.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When AE350 boots from flash, use CONFIG_OF_SEPARATE instead of
CONFIG_OF_BOARD.
Also remove unused code about prior_stage_fdt_address.
And modify CONFIG_SYS_FDT_BASE as flash address.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Add two defconfigs to support AE350 SMP booting from flash.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
For 32bit system, the OpenSBI (or BBL) will jump to 0x80400000 address
in S-mode whereas for 64bit system it will jump to 0x80200000 address
in S-mode.
Currently, the S-mode U-Boot sets SYS_TEXT_BASE to 0x80200000 for both
32bit and 64bit system. This breaks S-mode U-Boot for 32bit system.
This patch sets different SYS_TEXT_BASE for 32bit and 64bit system so
that S-mode U-Boot works fine for both.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Karsten Merker <merker@debian.org>
CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and
like some of the other similar boards requires bin_hdr.
bin_hdr (DDR3 init stage) is currently retrieved from the stock
bootloader and compiled into the kwb image.
Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip
support and writing env to SPI flash.
Signed-off-by: Luka Kovacic <me@lukakovacic.xyz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This add pinmux configuration for rgmii interface so that network
driver can be supported on K2G ICE boards. The pinmux configurations
for this are generated using the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
As this required some BUFFER_CLASS definitions, same is re-used
from the linux defnitions in include/dt-bindings/pinctrl/keystone.h
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch updates pinmux configuration for K2G GP EVM based on
data generated by the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Olimex A64-Teres-I board is a mainboard (the only one so far)
for Olimex Teres-I DIY laptop kit.
Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- MicroSD Slot
- 16GB eMMC Flash
- eDP LCD display
- HDMI
- USB Host
- Battery management
- 5V DC power supply
- Certified Open Source Hardware (OSHW)
Works:
- i2C
- MMC/SD
- PWM backlight
Known broken:
- Internal keyboard (seems to be because the keyboard firmware loads a
bootloader first, and then disconnects bootloader and connect real
keyboard). External ones connected to the USB port work fine.
This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).
Linux commit details about the sun50i-a64-teres-i.dts sync:
"arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins"
(sha1: d91ebb95b96c8840932dc3a10c9f243712555467)
Cosmetic warnings regarding whitespace and placement of SPDX notice for
dts file was ignored.
config and .dtsi file are adapted from pinebook files.
Tested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: move board entry in MAINTAINERS file at proper position]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add a version of samus which supports booting from TPL to SPL and then
to U-Boot. This allows TPL to select from an A or B SPL to support
verified boot with field upgrade.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add board code and DTs for Renesas RZ/A1 SoC-based GR-Peach,
which is a cheap development platform with RZ/A1H SoC. The
DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Currently supported are UART, ethernet and RPC SPI. The board
can be booted from RPC SPI by writing the u-boot.bin binary
to the beginning of the SPI NOR, e.g. using the "sf" command.
The board can also be booted via JTAG by setting text base to
0x20020000, loading u-boot.bin there via JTAG and executing it
from that address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Last change to this board was done in 2016, it uses non-DM USB
with no prospects of ever being converted to DM USB, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Last change to this board was done in 2016, it uses non-DM USB
with no prospects of ever being converted to DM USB, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Update the README to use the correct defconfig.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Drop Toradex ARM Support <support.arm@toradex.com> from maintainer email
list as this just clogs our support ticketing system.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
-----BEGIN PGP SIGNATURE-----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=SZ/W
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-05-03' of git://git.denx.de/u-boot-mips
- mscc: small fixes, enhance network support for Serval, Luton and Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
The ATF can pass additional information via the first four registers,
x0...x3. The R-Car Gen3 with mainline ATF, register x1 contains pointer
to a device tree with platform information. Parse this device tree and
extract DRAM size information from it. This is useful on systems where
the DRAM size can vary between configurations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
In Serval SoC family there are 2 different pcb, both of them have the same
phy, but with different version. Therefore implement board_phy_config
and set all the phys in the same way.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
When detecting the board, it was reading a register in the GPIO page of
the phy and based on that value it was making a decision. The bug was that
after the GPIO page for the first phy was set it was not reseted back.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
- at91sam9g20-taurus.dts: use labels
- cleanup taurus port to compile clean with
current mainline again. SPL has no serial
output anymore, so it fits into SRAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
In commit ad6054f1fe where support for the
Sancloud BeagleBone Enhanced (BBE) was added, new conditional
configuration of either MII pin muxing or RGMII pin muxing is done
depending on the board type. However, the old call to set up MII pin
muxing was not removed.
This may result in misconfiguration of the pin muxing for the BBE or
duplicate configuration for other boards and so we remove this obsolete
call.
Signed-off-by: Paul Barker <paul.barker@sancloud.co.uk>
There is a Factory RESET button on the back side of the Turris Omnia
router. When user presses this button before powering the device up and
keeps it pressed, the microcontroller prevents the main CPU from booting
and counts how long the RESET button is being pressed (and indicates
this by lighting up front LEDs).
The idea behind this is that the user can boot the device into several
Factory RESET modes.
This patch adds support for U-Boot to read into which Factory RESET mode
the user booted the device. The value is an integer stored into the
omnia_reset environment variable. It is 0 if the button was not pressed
at all during power up, otherwise it is the number identifying the
Factory RESET mode.
This patch also changes bootcmd to a special hardcoded value if Factory
RESET button was pressed during device powerup. This special bootcmd
value sets the colors of all the LEDs on the front panel to green and
then tries to load the rescue image from the SPI flash memory and boot
it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The regdomain environment variable is set according to value read from
EEPROM. This has to be done in board_late_init, after the environment
variables are read from SPI. Select CONFIG_BOARD_LATE_INIT in Kconfig
for the Turris Omnia target.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Since board watchdog is now unified and not handled in board files,
remove the unnecessary includes.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Unify the way how Omnia and Mox print board information (RAM size and
serial number).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Refactor RAM size reading from EEPROM in preparation for next patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This driver is required for Turris Omnia to read ethernet addresses.
Move the dependency from turris_omnia_defconfig to Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Refactor code which accesses the microcontroller and EEPROM via I2C.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The i2c slave disabling is done by mvtwsi driver and is not needed here.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
-----BEGIN PGP SIGNATURE-----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=CzWQ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The handling of regarding bootmode and early setup has been moved to
central location 'common/br_resetc.c', so use this on brxre1 board.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
On many B&R boards we have a reset-controller, responsible for very
early board-bringup (voltages, clocks, ...) and bootmode selection.
To be ready for adding more B&R boards to source tree while avoiding
duplicate code, we add the resetcontroller implementation to the common
part of B&R boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Many B&R boards are equipped with an I2C-EEPROM where various
information can be stored.
Today there is only a single byte for 'board_id' used.
We write this 'board_id' into environment for later use during boot.
If the value != 0xFF, meaning the byte is programmed, we modify the
"brdefaultip" environment variable for setting an IP-Address based on
board_id.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Today the BuR common stuff is only used on AM33XX boards. In future we
plan to have many other platforms than AM33XX so we have to move arch-
specific #include(s) to responsible #ifdef sections. By the way we drop
unneeded #include(s).
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
- Add DM based generic watchdog start and reset implementation
and remove all ad-hoc implementations (Stefan)
- Move mv_sdhci to DM (Pierre)
- Misc turris_omnia updates (Pierre)
- Change openrd targets to correctly build again (size changes
and fixes to the dts targets) and bring it back into Travis
builds (Stefan)
- Add Kirkwood db-88f6281-bp board (Chris)
With the latest size increase of the openrd boards, they all compile
clean again. Let's mark them as maintained again and add the Travis
job.
Please note that I can only compile-test these targets as I don't
have access to one of those boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert-u-boot@aribaud.net>
Cc: Vagrant Cascadian <vagrant@debian.org>
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.
Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.
With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Maxim Sloyko <maxims@google.com>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: "Álvaro Fernández Rojas" <noltari@gmail.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
This is Marvell's Kirkwood development board. It has the following
features
- 512M DDR2
- 2 PCI connectors
- 1 x1 PCI-e interface
- 1 Gigabit Ethernet Port
- 2 SATA Ports
- USB 2.0 Interface
- SDIO
- 128M NAND Flash
- 16M SPI Flash
It can be strapped to boot from SPI or NAND so there are two defconfigs
(one per boot media).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The boot commands have changed in the environment. Add a note about the
incompatible change and how resolve the issue in the board's README.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit c4bd12a7da ("i2c: mux: Generate longer i2c mux name") changed
the naming scheme of i2c devices within a mux. This broke references to
i2c@0 in the Turris Omnia board initialization code.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit switches to DM USB for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The four x16 DDR3 are wired in T-topology. From NXP AN4467:
'Although not required, T-Topologies may also benefit from performing
Write Leveling as there are package delays on both the processor and DDR
devices that can be de-skewed by performing Write Leveling. Therefore,
Freescale recommends determining Write Leveling calibration parameters
for all boards, regardless of topology used.'
That is why write level calibration is also done.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
The existing calibration values were found to be incorrect
in comparison to newly determined values.
The new values were generated with the help of 5 boards. They have
been determined with the NXP Utility 'DDR Stress Test (2.9.0)'.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This patch is necessary for convert this board to dm driver model
DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Migrate USB to using driver model.
Add USBH_PEN GPIO regulator.
While at it also add alias e.g. as required for UMS.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate pinctrl and regulators to device tree resp. driver model:
Ethernet, NAND and UART.
Drop BOARD_EARLY_INIT_F as it is anyway no longer used.
Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Disable output driver of PAD CCM_PMIC_STBY_REQ. This prevents the
SOC to request for a lower voltage during sleep. This is necessary
because the voltage is changing too slow for the SOC to wake up
properly.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Just give the new Ethernet PHY power save mode circuitry time to settle.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Using CPU temperature grading as a discriminator if the Wi-Fi /
Bluetooth chip is populated is no longer possible due to upcoming
SKUs. Set variant to -wifi only if a valid config block is present
and the product id mentions a SKU with Wi-Fi / Bluetooth.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Use CONFIG_TARGET_... at compile time to differentiate between
Apalis iMX6, Colibri iMX6 and Colibri iMX6ULL. Avoid code
duplication by moving question about Wi-Fi / Bluetooth before
IT/non-IT decision.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Add support for new Colibri iMX6ULL SKUs.
While at it also checkpatch fix the whole files.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Fix indentation using tab vs. spaces.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This setup is a bit special as Linux kernel (4.19) is not supporting
in-kernel NFS rootfs mount and Distributed Switch Architecture (DSA)
operation.
For that reason it was necessary to provide a bootarg to allow userspace
enable it afterwards if needed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
As EHCI on i.MX5 has been converted to driver model, the board specific
code, necessary for VBUS USB power supply setup is not needed anymore.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After commit efd0b79106 ("eth: dm: fec: Add gpio phy reset binding")
the in-board file definition of ETH PHY reset can be removed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
All socfpga boards except for vining_fpga use DM_I2C. Enable
DM_I2C for this board and set the EEPROM defines via Kconfig
(enabling CONFIG_I2C_EEPROM from MISC).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Series-changes: 2
- added (this) patch to move socfpga_vining to DM_I2C
This patch makes the on-board RTC work on the socfpga_socrates board.
This rtc is present on the board, but it does not work (fails with a
timeout).
This patch adds a weak pull-up on the I2C0-SCL pin connected to the m41t82
RTC on this board. While the SDA line has a pull-up on the pcb, the pull-up
on the SCL line seems to be missing. To work around this, enable the
weak-pull-up feature on this pin.
After applying this patch, the rtc timeout is gone and the 'date' command
can access the rtc chip.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlzAfvkACgkQfxc6PpAI
reYu9AgAjaFmydXjE8DxkSB3rR7DHZFTs1erVKAAL2v+Tdf7LDmz+j6u1M3v55WY
6r54f/gZ1UX5TEmQgEAKLa7QvvRO/lNvSGQnLHhZhv2IVWo7uWCKAUPdQ6XVZnUK
zO5v+ucs9Ne4HxQJHMC509HUIIBbydiRvUm8W0SeBZy4kEyJDuub4L+rpARkXNks
IZfKuY+VS4FK73D4M9PIhoXSubZgVS4AEcapakU1DvEz0kjsN4wr4idGrp3lutPC
455imz83JBq2+mx1oxclOGedkIDzTCq+nWQAwSftMehrJpGrp7RLNo0v4QZZUf4V
LIXRqObIYse9yQLkYPpeBdePMc8/tQ==
=0NJ2
-----END PGP SIGNATURE-----
Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dm
Various minor sandbox iumprovements
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
These two buffers currently conflict if tracing is enabled. Move the
pre-console buffer and update the documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if one of the initcalls fails on sandbox the address printing
is not help, e.g.:
initcall sequence 0000557678967c80 failed at call 00005576709dfe1f (err=-96)
This is because U-Boot gets relocated high into memory and the relocation
offset (gd->reloc_off) does not work correctly for sandbox.
Add support for finding the base address of the text region (at least on
Linux) and use that to set the relocation offset. This makes the output
better:
initcall sequence 0000560775957c80 failed at call 0000000000048134 (err=-96)
Then you use can use grep to see which init call failed, e.g.:
$ grep 0000000000048134 u-boot.map
stdio_add_devices
Of course another option is to run it with a debugger such as gdb:
$ gdb u-boot
...
(gdb) br initcall.h:41
Breakpoint 1 at 0x4db9d: initcall.h:41. (2 locations)
Note that two locations are reported, since this function is used in both
board_init_f() and board_init_r().
(gdb) r
Starting program: /tmp/b/sandbox/u-boot
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/x86_64-linux-gnu/libthread_db.so.1".
U-Boot 2018.09-00264-ge0c2ba9814-dirty (Sep 22 2018 - 12:21:46 -0600)
DRAM: 128 MiB
MMC:
Breakpoint 1, initcall_run_list (init_sequence=0x5555559619e0 <init_sequence_f>)
at /scratch/sglass/cosarm/src/third_party/u-boot/files/include/initcall.h:41
41 printf("initcall sequence %p failed at call %p (err=%d)\n",
(gdb) print *init_fnc_ptr
$1 = (const init_fnc_t) 0x55555559c114 <stdio_add_devices>
(gdb)
Signed-off-by: Simon Glass <sjg@chromium.org>
With the migration to DM in SPL and the DT support, the
old legacy code is no longer neaded, so this patch removes it
Signed-off-by: Adam Ford <aford173@gmail.com>
This is needed to make ethernet work on stm32f746-eval which
uses MII mode.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Amlogic U200 board is based on the Amlogic S905D2 SoC
from the Amlogic G12A SoC family.
The board has the following specifications :
- Amlogic S905D2 ARM Cortex-A53 quad-core SoC
- XGB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
- MIPI DSI Connector
- Audio HAT Connector
- PCI-E M.2 Connector
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When fixing sandbox test for regmap_read_poll_timeout(), the
sandbox_timer_add_offset was introduced but only defined in sandbox code
thus generating warnings when used out of sandbox :
include/regmap.h:289:2: note: in expansion of macro 'regmap_read_poll_timeout_test'
regmap_read_poll_timeout_test(map, addr, val, cond, sleep_us, \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c:169:8: note: in expansion of macro 'regmap_read_poll_timeout'
ret = regmap_read_poll_timeout(spifc->regmap, REG_SLAVE, data,
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c: In function 'meson_spifc_txrx':
include/regmap.h:277:4: warning: implicit declaration of function 'sandbox_timer_add_offset' [-Wimplicit-function-declaration]
This fix adds a timer_test_add_offset() only defined in sandbox, and
renames the previous sandbox_timer_add_offset() to it.
Cc: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
Fixes: df9cf1cc08 ("test: dm: regmap: Fix the long test delay")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvW07AAoJEB6zHgIOrC/Iu4QH/1REDOTrsZPydd2yD/O81vPs
RiLC8wP2J4UmqtMcNTLyvxlYwrzqoR5J6SYdyBNU/+cLEp/gdzEI+rjsfSV2uRX1
Qb4Pk2FiI503JVjegxsbJqzASfiEP7rIg3HM5431xbhYH22MW2FH6le6yrtNxjBh
m1WFjQYX1bpbGb6zue8TgyLIeN1IqWuqnH9kUHixUEan+xrpEhN239LDFjdvGbvC
BvYyMtDddmMt4YDzNjgX36us993kylGZp6JijR3zgUao7I/JGVZAJrxw8MHDTnVy
UKv3VI9F5bGLSvzqTVL2MFU6XtJW26v+niGLhGzlUhb3TTKrdKOicm3VF7tO+JU=
=MamK
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-b' of git://git.denx.de/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2019.07 cycle
The DK1 and DK2 boards use the USB Type-C controller STUSB1600.
This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller
to check cable detection.
- the DWC2 driver to support a new dt property
"u-boot,force-b-session-valid" which forces B session and
device mode; it is a workaround because the VBUS sensing and
ID detection isn't available with stusb1600.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Use the DWC2 device driver with DM_USB_GADGET support and
cleanup the USB support in STM32MP1 board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
Linux commit details about the sun50i-h6-beelink-gs1.dts sync:
"arm64: dts: allwinner: h6: Introduce Beelink GS1 board"
(sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193)
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SAMA5D2 ICP Board features the SAMA5D27 SoC,
together with QSPI Flash, Wilc3000 wireless device and
EtherCat support.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly262oACgkQykllyylKDCH44gCbBnuxUH6ZF0B7Leuee4te7C59
LmUAn14/bbtMt17zkMSADCjY9yGWF4au
=mWrW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze
Xilinx/FPGA changes for v2019.07
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
It seems like the Allwinner SATA driver is already quite capable of
using the driver model, so we can force this on all boards and can
remove support for a non-DM_SCSI build.
This removes the warning about boards with SATA ports not being
DM_SCSI compliant.
It also takes the opportunity to move the driver out of the board/sunxi
directory to join its siblings in drivers/ata, and to make it a proper
Kconfig citizen.
The board defconfigs stay untouched.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: select DM_SCSI separately]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Since Ethernet clock and reset is now handling via
CLK and RESET frameworks via driver API's remove
explicit ccm writes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch adds "zu39dr" to the list of zynqmp devices
The zu39DR is the new RFSoC silicon with id value of 0x66.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch checks for zynq aes & rsa commands max parameters count. Also
checks minimum number of parameters count for aes command.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Changed the return type of reset_reason() to int from u32, because
zynqmp_mmio_read/write() returns signed value on error.
Replaced readl and writel functions with zynqmp_mmio_read &
zynqmp_mmio_write functions to access RESET_REASON(CRL_APB) registers.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
-----BEGIN PGP SIGNATURE-----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=KLsH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imx
Move to DM
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
ipu.h header is not found since the ipuv3 driver was moved to
the drivers/video/imx subdirectory. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix toradex_modules array off by one issue potentially leading to
spurious printout during boot e.g.
Model: Toradex V1.2A,
instead of
Model: Toradex UNKNOWN MODULE V1.2A.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
If the config block is missing, various things may fail or behave
strangely on certain modules. This patch unifies that behaviour by
using a fake MAC address, until user updates the config block.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The DDR validation tool (which is part of Processor Expert) allows
to evaluate leveling parameters for CR105/CR106/CR110. Several
runs have been made with Colibri VF50 and VF61 and it seems to
evaluate very similar values. Use this values by default.
Note: The newly evaluated parameters seem to require CTLUPD_AREF
to be enabled!
Note 2: The tool also evaluated 6 as a new value for PHY02/18
GATE_CFG (Coarse adjust of gate open time). However, this seems
not to work in practise.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Using the DDR Validation tool in Processor Expert uncovered two
timing inconsistencies. Since those timings are related to the
suspend mode they do not affect or change regular memory behaviour.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Use similar info message as on other modules.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate FEC, ESDHC, NFC and USB to driver model.
While at it also do no longer enable optional I2C clock in board file as
the generic clock code now handles this. Note for space reason and as
it is not required just for booting we do not enable I2C in U-Boot by
default.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate pinctrl and regulators to device tree resp. driver model: DDR,
DSPI, ENET, ESDHC, I2C, NFC and UART.
Enable CMD_DM, PINCTRL and DM_REGULATOR.
While at it also update copyright period and sort include files.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Update device tree in preparation of further driver model migration:
Ethernet FEC, ESDHC aka MMC/SD card, I2C, NFC aka NAND flash controller,
USBH_PEN GPIO regulator.
Add iomux resp. pinctrl entries to be removed from proprietary platform
data: DSPI, ESDHC, FEC, I2C, NFC, UART, USBH_PEN GPIO.
Introduce a U-Boot specific device tree with some required
u-boot,dm-pre-reloc properties: soc, aips0, pinctrl_ddr and uart0 incl.
pinctrl.
While at it also update the MAINTAINERS file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Spotted two missing spaces in comments.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
... as preparation for additional driver model coonversions.
We use CONFIG_OF_EMBED here to keep u-boot.imx as final binary name. So we
maintain compatibility with the original TBS u-boot and available HOWTOs
for u-boot updates.
Signed-off-by: Soeren Moch <smoch@web.de>
The PMIC on the Colibri iMX6 may have ECC errors in fuses that will
prevent correct settings. Up to one bit error per fuse bank can be
reported and corrected by the ECC logic. Two bit errors can only be
reported.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
RGMII_RD1 pin (active high, GPIO6_IO27) is triggered on reboot during
the SPL phase. This asserts (active low) nReset_Out from the PMIC.
Only V1.1 and later Colibri iMX6 modules implement this in hw. Previous
versions do not use this pin, so it is safe to leave it enabled at all
times.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Make sure CMA memory is not greater than 50% of available physical
memory.
Allow user to change the CMA memory via 'cma-size' U-Boot environment
variable.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
We have two commands to change the bootmode fuses:
mfgr_fuse which set fuse 0/5 and 0/6
and
updt_fuse which burns bit 4 of 0/5.
Before Image 2.6 we fused in mfgr_fuse 0x5062, which boots
from the user partition of the eMMC.
To workaround certain hangs we moved to fastboot mode and
using the first bootpartition of the eMMC requiring a fuse
value of 0x5072 which could be achived by the then added
updt_fuse command. At the same time the mfgr_fuse command
was changed to also fuse 0x5072, revert that second change
so that one can fuse both values, one with just mfgr_fuse
and the later with mfgr_fuse;updt_fuse.
Note that the mfgr_fuse command is only needed at module
production time, a customer might need to use updt_fuse
when upgrading an older module to be compatible with a
newer image. The command is integrated into the image
update scripts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Colibri iMX6 V1.1 HW can use the PMIC GEN3 to power the NVCC_SD1.
Change the settings fused into the PMIC's OTP to powerup with
GEN3 set to output 3.3V.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.
Disable the bits also on UARTs not used in the boot loader to prevent
an interrupt storm when Linux enables the UART interrupts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Keep debug code at the end of the function.
Use a one line informational message for the PMIC only.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In the linux device tree we use 40Ohm drive strenght. So use the same
value in U-Boot.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Print also for Colibri iMX6 512MB IT with 64-bit RAM bus.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This doesn't do anything anymore, probably never did.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Migrate GPIOs to using driver model, properly request backlight, MMC/SD
card detect and USB power enable GPIOs and also enable SION bit in pin
muxing for auxiliary, backlight and USB power enable GPIOs.
While at it also update copyright year, clean-up/re-order includes, add
some comments clarifying ifdef scope and do some white-space clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now with SPL long since being in place even for recovery using SDP
finally get rid of those nospl configurations.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The PMIC on Apalis iMX6 may have ECC errors in fuses that will prevent
correct settings. Up to one bit error per fuse bank may be reported and
corrected by the ECC logic. Two bit errors can only be reported.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
We have two commands to change the bootmode fuses:
mfgr_fuse which set fuse 0/5 and 0/6
and
updt_fuse which burns bit 4 of 0/5.
Before BSP 2.6 we fused in mfgr_fuse 0x5062, which boots
from the user partition of the eMMC.
To workaround certain hangs we moved to fastboot mode and
using the first bootpartition of the eMMC requiring a fuse
value of 0x5072 which could be achieved by the then added
updt_fuse command. At the same time the mfgr_fuse command
was changed to also fuse 0x5072, revert that second change
so that one can fuse both values, one with just mfgr_fuse
and the later with mfgr_fuse;updt_fuse.
Note that the mfgr_fuse command is only needed at module
production time, a customer might need to use updt_fuse
when upgrading an older module to be compatible with a
newer image. The command is integrated into the image
update scripts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.
Disable the bits also on UARTs not used in the boot loader to prevent
an interrupt storm when Linux enables the UART interrupts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Keep debug code at the end of the function.
Use a one line informational message for the PMIC only.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In the Linux device tree we use 40Ohm drive strength. So use the same
value in U-Boot.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This doesn't do anything anymore, probably never did.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Migrate GPIOs to using driver model, properly request backlight,
Ethernet PHY reset, MMC/SD card detect and USB power GPIOs and also
enable SION bit in pin muxing for Apalis, backlight, eMMC reset,
Ethernet PHY reset and USB power enable GPIOs.
While at it also update copyright year, clean-up/re-order includes,
add some comments clarifying ifdef scope and do some White-space
clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now with SPL long since being in place even for recovery using SDP
finally get rid of those nospl configurations.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
BK4 requires setup of 50MHz reference clock for its KSZ8081 PHY devices.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This code allows reusing the default u-boot as in the late board init, the
default envs are restored and proper recovery scripts executed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The "m4go" provides exactly the same functionality as the IMX generic
"bootaux" command. Remove it to not duplicate the code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
As the I2C2 clock is now enabled in the generic clock code, we can remove
this code from a board file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
-----BEGIN PGP SIGNATURE-----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=NrV8
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mips
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
- Misc dts files sync'ed with Linux version (Chris)
- Orion watchdog fix (Chris)
- kwbimage changed to also support Marvell bin_hdr binary (Chris)
- Add DM support to enable CONFIG_BLK for sata_mv (Stefan)
- Enable BLK on multiple platforms (Stefan)
- Misc minor fixes to AXP theadorable board (Stefan)
- Correct logic for DM_SCSI + unconverted drivers check (stefan)
- Misc changes to kirkwood to enable DM_USB here (Chris)
- Change ahci_mvebu to enable usage on A38x (Baruch)
- Update the kirkwood entry in git-mailrc (Baruch)
- Misc minor improvements (turris, documentation) (Baruch)
- Enhance sata_mv to support Kirkwood as well (Michael)
- Add wdt command (Michael)
- Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG
board support (Chris)
In Jaguar2 SoC family there are 3 different pcb. Each of this needs
to configure the phys in different ways. Therefore implement the
function board_phy_config and based on pcb configure them accordingly.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
QCA9563 is CPU used on AP152 board :
Clock speed : 750 MHz ,
Arch : Mips 74Kc,
Eth : SGMII interface,
MIMO config : 3 * 3 450M,
2 * USB 2.0,
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2:
- coding style cleanup
- remove ununsed flash chip in defconfig
- enable automatic icache / dcache size in defconfig
Changes for v3:
- add detailed information for qca956x in commit message
Changes for v4:
- remove pre-configured network settings in ap152.h
Changes for v5:
- coding style cleanup
In order to insure that hog GPIOs are configured early during
the boot process, force all pinctrl driver probing in board_init().
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
For DK1/DK2 boards, check if power supply provides enough current
to allow the board to boot correctly.
ADC@0 channel 18 and 19 are connected to USB type-C CC1 and CC2
signals. The table below shows the behavior for different range of
CC1 or CC2:
range | power supply | red led | console message
(Volts) | (Amps) | blinks |
--------------|--------------|---------|-----------------------------------
[2.10 - 1.23[ | 3 | NO | NO
[1.23 - 0.66[ | 1.5 | 3 times | WARNING 1.5A power supply detected
[0.66 - 0] | 0.5 | 2 times | WARNING 500mA power supply detected
If detected current is < 3A, red led is kept ON after blinking.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Alignment with STPMIC1 datasheet
s/MAIN_CONTROL_REG/MAIN_CR/g
s/MASK_RESET_BUCK/BUCKS_MRST_CR/g
s/MASK_RESET_LDOS/LDOS_MRST_CR/g
s/BUCKX_CTRL_REG/BUCKX_MAIN_CR/g
s/VREF_CTRL_REG/REFDDR_MAIN_CR/g
s/LDOX_CTRL_REG/LDOX_MAIN_CR/g
s/USB_CTRL_REG/BST_SW_CR/g
s/STPMIC1_NVM_USER_STATUS_REG/STPMIC1_NVM_SR/g
s/STPMIC1_NVM_USER_CONTROL_REG/STPMIC1_NVM_CR/g
and update all the associated defines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Alignment with kernel driver name & binding
introduced by https://patchwork.kernel.org/cover/10761943/
to use the final marketing name = STPMIC1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Prepare file modification for kernel alignment and
rename driver to stpmic1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Initialize the system configuration for basic boot
- update interconnect setting
- disable pull-down for boot pin
- enable High Speed Low Voltage Pad mode for SPI, SDMMC, ETH, QSPI
- activate I/O compensation
Done by SSBL = TF-A for trusted boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Clearly separate bootcmd for stm32mp1 board
(bootcmd_stm32mp) and preboot management.
That solve issue for fastboot continue command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Set board name with the first dts compatible found in DT
code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
The result with DEVICE_TREE=stm32mp157c-ev1 is:
STM32MP> env print
board=stm32mp1
board_name=stm32mp157c-ev1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Implement checkboard() function to display
- the boot chain used: basic or trusted
- the board compatible in device tree
- the board identifier and revision, saved in OTP59 for ST boards
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Missed few mails from openedev, since most of the day I look at
amarulasolutions mail so update the same.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When booting the am3517-evm, the following message appears:
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
This patch implements spl_start_uboot to clear this message
and allow device to know if it should boot U-Boot or kernel.
Fixes: 1c6b6f383a ("ARM: am3517_evm: Enable Falcon Mode")
Signed-off-by: Adam Ford <aford173@gmail.com>
The SPL image overflows when cpsw dt nodes are added and SPL_OF_CONTROL
is enabled. Use static platdata instead to save space.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Create a ft_board_setup() api that gets called as part of
DT fixup before jumping to kernel. In this ft_board_setup()
call fdt_fixup_msmc_ram that update msmc sram node.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
If SW 8 pins 0 and 1 indicate that NAND should be enabled then
the pins pinmux must be reconfigured for NAND mode.
Therefore, enable NAND by reconfiguring the pinmux.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
By default VOUT3 occupies the pins required for NAND. Therefore, create
a seperate entry that can be use to reconfigure these pins to work for
NAND.
On the EVM SWITCH 8 pins 0 and 1 will be used to determine if NAND is
enabled or not. For NAND to be selected pin 0 should be on and pin 1
should be off. Any other combination will assume NAND shouldn't be
enabled.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
With the memory mapping giving us some more avialable RAM, this
updates the da850-evm-u-boot.dtsi to include the serial port, SPI
and Flash nodes along with some dependent nodes in the SPL dtb.
This also removes the platform data initialization code for the
serial port and SPI Flash.
Signed-off-by: Adam Ford <aford173@gmail.com>
In order to fully support SPL_OF_CONTROL, we need BSS to be a bit
larger. This patch relocates BSS to SDRAM instead of SRAM which
is similar to how ARMv7 boards (like OMAP2+) do it.
This means two new variables are required:
CONFIG_SPL_BSS_START_ADDR set to DAVINCI_DDR_EMIF_DATA_BASE
CONFIG_SPL_BSS_MAX_SIZE is set to 0x1080000 which is 1 byte
before the location where U-Boot will load.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch adds a workaround to reset the phy one time during boot
using GPIO0 pin 10 to make sure, the Phy latches the configuration
from the input pins correctly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch updates pinmux configuration for K2G GP EVM based on
data generated by the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This add pinmux configuration for rgmii interface so that network
driver can be supported on K2G ICE boards. The pinmux configurations
for this are generated using the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
As this required some BUFFER_CLASS definitions, same is re-used
from the linux defnitions in include/dt-bindings/pinctrl/keystone.h
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DB-XC3-24G4XG is a switch development board from Marvell. It can
either use and external CPU card such as the db-88f6820-amc or the
internal CPU that is integrated into the switch.
Add support for running U-Boot on the internal CPU and enable the USB,
SPI and NAND peripherals. For now this needs the bin_hdr from the
Marvell U-Boot for this board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the PCIe port specific link capabilities configuration
for Armada XP. The weak function board_sat_r_get() was used to return
a common flag for PCIe Gen1 vs Gen2 capability for all PCIe ports. This
is now changed with this patch to return a bit per PCIe port (4 bits
in this case, bit 0 for PCIe port 0, etc).
The theadorable board uses this new feature to configure PCIe port 0
as Gen1 and all other PCIe ports as Gen2 capable. All other AXP boards
using this function are not changed in the configuration and still
configure all ports as PCIe Gen2.
This patch also removes the parameter "pex_mode" from
board_serdes_cfg_get() as this parameter was not used in any of the
implementations.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Document build and install of U-Boot image on Clearfog with eMMC.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The check for the missing PEX switch can lead to an infinite loop, when
the PCIe device is not found. It is helpful to enable the user to break
out of this boot-loop, to enable booting to the prompt for test cases.
This patch adds a 3 second delay in the error case before rebooting.
The user can press Ctrl-C in this time to abort the boot-loop.
This patch also calls bootcount_inc() before rebooting in the error
case. This is needed to increment the bootcounter, since this function
is called earlier than the main bootcounter increment. Otherwise the
bootcounter will not be incremented in the error case at all.
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the hardware watchdog to guard against system lock ups when
running in the SPL or U-Boot. Stop the watchdog just before booting so
that the OS can re-enable it if needed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The generic wdt_start API expects to be called with the timeout in
milliseconds. Update the orion_wdt driver to accept a timeout in
milliseconds and use the clock rate specified in the dts to convert the
timeout to an appropriate value for the timer reload register.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
LibreTech AC is a single board computer manufactured by Libre Technology
with the following specifications:
- Amlogic S805X ARM Cortex-A53 quad-core SoC @ 1.2GHz
- ARM Mali 450 GPU
- 512MiB DDR4 SDRAM
- 10/100 Ethernet
- HDMI 2.0 4K/60Hz display
- 40-pin GPIO header
- 4 x USB 2.0 Host
- eMMC, SPI NOR Flash
- Infrared receiver
The u-boot specific code is the same as the P212 support,
so use the P212 board support code with a distinct defconfig
and config include files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds support for p201 reference boards
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds the defconfig and README files for p200 board
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This renames the odroid-c2 to p200 and set it as the default GXBB board
Other boards (odroid-c2 and nanopi-k2) will inherit from p200
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
v2018.01 commit e23eb942ad ("ARM: rmobile: Stop using
rcar-common/common.c on Gen3") removed
board/renesas/rcar-common/common.c from the build chain with the
reasoning that calling arch_preboot_os() is no longer needed.
However, it left the arch_preboot_os() in place. Get rid of it.
This is done in preparation of resurrecting rcar-common/common.c.
NOTE: The three removed header includes (io.h, sys_proto.h, rcar-mstp.h)
are in direct relationship with the dropped arch_preboot_os() hook. The
other headers (common.h, rmobile.h) are going to be needed by pretty
much anything that is going to appear in the rcar common code. So, keep
the two in place.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Add defconfig and board specific adjustments for the R8A77965 M3N ULCB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcrEcDAAoJEB6zHgIOrC/I1dgH/3mHQNW8bqiNCJYcoVQdheHb
e06TqbWHNlOG/NilYybvdeF+LjeCqhX4PzyL/sdcyBf3D/tK4cVvHpZrQyjb2s6K
5IZSKJ+cZznmq6Hv7b//d30Azhx8bi8luxs60kkj+PF0xI1EyU3JteUqAs4Ooxd7
z+HdcRFuAaps6sy0+szB3fTw9HTGrhFvQuHasDGb2uahhpwGzu/P0RchIDksOdzH
3L4EOvgq8MZCiZ3ZtFWMWzQoCjcKf5Fuux41qar8gG/LrkWRfKG+LfWfZtTiTsjf
vC9bYWmdKtkSLFj1PWgLBfGxev5zwPUbqI2EP4OlagfNs3os5pVFCYV5NZ6ovdE=
=kMXf
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.07 cycle
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip
AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage.
This patch adds support for this board including SPL support. Therefore
the AT91Boostrap is not needed on this platform any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Migrate the following options to CONFIG_DM:
CONFIG_DM_GPIO
CONFIG_DM_MMC
CONFIG_DM_ETH
CONFIG_DM_SERIAL
CONFIG_DM_USB
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
After building ATF it is needed to copy the generated bl31.bin file to
the U-Boot source tree.
Make this step explicit in the instructions.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Since commit 9e3c0174da ("pico-imx7d: Add LCD support") we started to
notice some hangs in U-Boot.
There is not an issue on such commit per se, but due to the LCD support
the current drawn is increased and this may cause issues when powering
pico-imx7d-pi from USB.
Some computers may be a bit strict with USB current draw and will
shut down their ports if the draw is too high.
The solution for that is to use an externally powered USB hub between the
board and the host computer.
Add such recommendation to the README file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
After the DM_MMC conversion the following eMMC boot error is observed:
U-Boot SPL 2019.04-rc4 (Mar 20 2019 - 18:53:28 +0000)
Trying to boot from MMC1
MMC Device 0 not found
spl: could not find mmc device 0. error: -19
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This happens because the SPL code does not initialize the SDHC pins
and clock.
Fix it by moving the original eMMC initialization from U-Boot proper
to SPL.
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
The I2C bus number to access the PMIC is I2C 7, fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The PHY LED mode register mask should be 0xc000 , not 0xc0000.
Correct the mask to operate on the right bits.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R8A7794_ETHERNET_B config option is unused and based on the
description, this is a setting which should be fully done on a
DT level instead. Remove this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
I took over maintainership from Alex Graf with commit
3157bbfa18 ("rpi: Make Matthias maintainer")
But I forgot to update the board maintainer file.
This patch adds myself to the game.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@csgraf.de>
On AXS10x boards we have non-standard NAND controller
which was never really used a lot as there're other much more
convenient [as they are standard & removable] persistent media
like SD-card and USB mass storage.
Moreover after recent changes we face with some NAND controller
runtime issues. So instead of keeping support of yet another
non-standard peripheral we're dropping its support for good.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Define the function board_spi_cs_gpio only when needed,
only called in drivers/spi/mxc_spi.c.
That avoid compilation issue for tqma6s_wru4_mmc_defconfig
when CONFIG_SF_DEFAULT_BUS and CONFIG_SF_DEFAULT_CS are not
defined (CMD_SF not defined) after migration in KConfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When these were moved from mach-omap2 to board files they got placed
inside TI_SECURE_DEVICE ifdef block, they are not secure only, move
them up and out.
Fixes: 413b90777f ("ti: fastboot: Move weak overrides to board files")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Now that we are representing the MDIO mux in LX2160AQDS board in
producer/consumer terms, the consumer nodes' has been changed.
Therefore, modify the device tree fixups according to change in device
tree.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The information in the SabreLite README is inaccurate and sparse. The
upstream U-Boot can boot the SabreLite from SPI-NOR. Additionally, the
freely available imx_loader tool can be easily used to boot a board with a
corrupted SPI, the official Freescale/NXP manufacturing tools are not
required.
Reformat the document, adding a description of how to boot from SPI-NOR
and adding a brief description of how to recover the board should the
SPI-NOR be corrupted using imx_loader.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
The third parameter of the pmic_clrsetbits() function is the mask
to the register and the correct mask is 1 not 0.
Since the LDOGCTL only contains a single valid bit (bit 0),
we can use pmic_reg_write() and write 1 directly, which fixes
the problem in a simpler way and use the original pmic function
that was used prior to the DM PMIC conversion.
Fixes: 8ba377321c ("arm: imx7s-warp: Convert to DM PMIC")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
There is no need to store the values written to the PMIC inside the
'reg' variable. Make it simpler by writing the values directly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
After DM conversion the I2C and MMC related board codes have been
removed, so remove the corresponding header files as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
This patch mostly enables DM drivers in board defconfig and all their
dependencies. Additionally we remove USB code that is on longer
executed after enabling CONFIG_DM_USB. Enable CONFIG_PINCTRL, so we
can get rid of ethernet pin configuration.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Convert to use DM_PMIC for the PFUZE3000. Since this PMIC is
under an I2C bus, conver to DM_I2C as well.
Also, since I2C is not used in SPL, remove CONFIG_SPL_I2C_SUPPORT
to avoid build warnings.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Convert to CONFIG_DM_GPIO.
Also, DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation, so do as requested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Select CONFIG_DM_MMC=y in order to support MMC driver model.
This allows the MMC board related code to be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
CONFIG_BOARD_TYPES is necessary for Odroid X/X2/U3 boards to detect
proper revision. However building should succeed even without it.
While moving code around, document also the reference clock selection.
This fixes the build error without CONFIG_BOARD_TYPES:
board/samsung/odroid/odroid.c: In function 'board_usb_init':
board/samsung/odroid/odroid.c:473:8: error: 'gd_t' {aka 'volatile struct global_data'} has no member named 'board_type'
if (gd->board_type == ODROID_TYPE_U3)
^~
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Various places in the code set "boardname" env property. It was used
for booting from ITB images and choosing proper DTB file name. Instead
of duplicating it, use existing U-Boot wide - "board_name".
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Last activity from Arndale (Exynos5250) board maintainer Chander Kashyap
was in January 2014 (Signed-off). Recently his samsung.com email
bounces with 550 (5.1.1 Recipient address rejected: User unknown).
Add Krzysztof Kozlowski as odd fixer for this board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Fix detection of Odroid HC1 (Exynos5422) after reboot if kernel disabled
the LDO4/VDD_ADC regulator.
The LDO4 supplies both ADC block and the ADC input AIN9. Voltage on
AIN9 will rise slowly, so use delay of 5 milliseconds instead of
timers-based loop to wait for voltage stabilization.
First reads on Odroid HC1 return 305, 1207, 1297 and finally 1308
(reference value is 1309).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Printing the "Type" of board requires proper detection of revision which
can happen only late because regulators are needed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Detection of board revision is done early - before power setup. In case of
Odroid XU3/XU4/HC1 family, the detection is done using ADC which
is supplied by LDO4/VDD_ADC regulator. This regulator could be turned
off (e.g. by kernel before reboot). If ADC is used early, the
regulators are not yet available and the detection won't work.
Split the revision detection out of set_board_type() into separate
function called later - either when displaying board info (in late mode)
or during misc_init_r. The idea is that set_board_type() will be called
early so its method of detection are limited to flattened device tree
(exynos5-dt-types.c for Exynos5) or GPIO (odroid.c for Exynos4412). The
newly added set_board_revision() can be called only later, when
resources like regulator are available.
This is necessary to fix the detection of Odroid HC1 after reboot, if
kernel turned off the LDO4 regulator.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Kconfig checked for SoCFPGA Arria10 as a platform, instead of
checking for specific board configuration, which works with one
single platform in tree, but not with multiple. Fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
- Enable DHCP as boot-source in distro boot for NXP layerscape
platforms
- fix register layout for SEC on Layerscape architectures
- fixes related to DPAA2 ethernet
Path for fsl-mc node in kernel device-tree is /soc/fsl-mc whereas
in u-boot it is /fsl-mc.
Fix the incorrect search path to fix following error:
fdt_fixup_board_enet: ERROR: fsl-mc node not found in device tree
(error -1)
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Same issue for ls2080a was fixed by following patch:
b7b8410a8f ls2080: Exit dpaa only right before exiting U-Boot
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
T1040RDB has been upgraded to support new DDR ie. MTA9ADF1G72AZ-3G2, 8GB.
So adding support of new DDR part by updating board_specific_parameters
udimm0.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch adds SiFive FU540 board support. For now, only
SiFive serial, SiFive PRCI, and Cadance MACB drivers are
only enabled. The SiFive FU540 defconfig by default builds
U-Boot for S-Mode because U-Boot on SiFive FU540 will run
in S-Mode as payload of BBL or OpenSBI.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The QEMU CPU support under arch/riscv is pretty much generic
and works fine for SiFive Unleashed as well. In fact, there
will be quite a few RISC-V SOCs for which QEMU CPU support
will work fine.
This patch renames cpu/qemu to cpu/generic to indicate the
above fact. If there are SOC specific errata workarounds
required in cpu/generic then those can be done at runtime
in cpu/generic based on CPU vendor specific DT compatible
string.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot typically tears down the display controller before handing
control over to Linux. On LCD displays disabling pixel clock leads to a
fading out effect with vertical/horizontal lines. Make sure to disable
back light before booting Linux.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Switch to using the omap3-u-boot.dtsi file for needed properties.
- Remove a few SPL features to free up more SRAM space.
- Switch CONFIG_SYS_TEXT_BASE to the normal default, we don't need to
worry about X-Loader at this point anymore.
- A few related updates to SPL options as part of switching to DM SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With the generic omap3-u-boot.dtsi file available, this patch
increased the memory of the various incarnations of the omap3_logic
board, and points their respective u-boot.dtsi files to the newly
created generic one, and removes the PLATDATA from the board file.
These are all done at once because the're all utilizing the same
omap3logic.c board file.
Signed-off-by: Adam Ford <aford173@gmail.com>
The README.da850 file continues information on how to burn NAND
for the LCDK, but not the DA850-EVM. This patch adds both the
commands and dip switch instructions for burning and booting
NAND.
Signed-off-by: Adam Ford <aford173@gmail.com>
We use TARGET_BCM63158 in the Kconfig instead of ARCH_BCM63158,
so we could add other board that use a bcm63158.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This commit converts the brxre1 board to DM,
for this we have todo following things:
- add a devicetree-file for this board
- drop all obsolete settings from board header-file
- use dm_i2c_xxx calls for read/write to the resetcontroller
- request gpios before operate them
Serues-cc: trini@konsulko.com
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add init_func_vid() which calls adjust_vdd()
This ensures adjust_vdd() is called via
init_sequence_f[]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Adds esbc validate command for verification of MC and DPC
firmware, along with secure boot defconfig.
Also enable distro boot.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: squash "enable DM support for SATA patch" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As the H5 is pin compatible with the H3, vendors tend to upgrade their
existing H3 products with an H5 SoC swap. This is the case with the
Bananapi M2+ H5.
Add the following to support it:
- device tree file: synced from Linux v5.0-rc1,
- defconfig: copy of bananapi_m2_plus_h3_defconfig with only SoC
family and default device tree file name changed
- MAINTAINERS entry
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The brand Sinovoip is used for Sinovoip's original VOIP products, while
the Bananapi brand is for the single board computers they produce. This
has been verified by Bananapi. Rename the board from "Sinovoip BPI M2
Plus" to "Bananapi M2 Plus". For the defconfig file, all lowercase is
used.
To support the H5 variant of this board, the "H3" suffix is added to
the defconfig name.
Also add myself as one of the board maintainers.
As the device tree files were already correctly named, they do not
require any changes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: removed unneeded message from commit body]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
xilinx:
- Start to use distro boot commands first
- Setup fdtfile on ZynqMP
- Move mac addr eeprom read to common location
- Convert to OF_SEPARATE
- Switch all board to DM_I2C
- Some DT syncs
i2c:
- Remove !DM_I2C zynq driver
versal:
- Enable some more features
- Add mini configurations
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlxmyM0ACgkQykllyylKDCF9hwCdF6C9PHvg3w6jf1OKBS9yDDYP
Ch8AniRwxHkbAQC7eG98xoaftzEPLvAw
=AWZ0
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.04-rc2' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2019.04-rc2
xilinx:
- Start to use distro boot commands first
- Setup fdtfile on ZynqMP
- Move mac addr eeprom read to common location
- Convert to OF_SEPARATE
- Switch all board to DM_I2C
- Some DT syncs
i2c:
- Remove !DM_I2C zynq driver
versal:
- Enable some more features
- Add mini configurations
device-tree paths should never be used that reference node addresses
making an assumption about leading zeros. They should not be there per
the device-tree specification however they have been there until Linux
4.15 when they were removed via kernel commit
8dccafaa281aa1d240a58bbcdff338aec114a021.
This fixes various issues which will occur when using Linux 4.15+
that are being fixed up on a per model per PCB revision basis such as:
- enabling MMC UHS-I on board revisions that support it
- enabling PWM based on hwconfig
- fixing PCIe reset on GW552x
- removing cpu external watchdog reset on boards that do not support it
- populate PCI dt nodes based on PCI scan in order to fix GW16082
interrupt mapping and inject MAC address for PCI based GbE
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5904/GW5909 have a SP33E multi-protocol serial transceiver which we
want to configure to RS232 by default (by de-asserting RS485_EN)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5909 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW5904 but with half the DRAM loaded
and an additional RS232 transceiver off UART2.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5908 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW530x but with 1GiB density DRAM
(64bit 512MiB).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5907 is a small single board computer based on the i.MX6DL SoC
with the following peripheral set:
- DDR3 memory (512MB default)
- 1x GigE (i.MX6 FEC)
- Gateworks System Controller
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5905 is single-board tablet computer based on the i.MX6 SoC with the
following peripheral set:
- eMMC flash (boot device)
- microSD expansion
- LVDS display connector for off-board 3D+1C with PWM backlight
and I2C based touch controller
- MIPI camera connector supporting the TRULY CM8487-B500SA-E (OV5640)
- ublox EMMY-W1 WiFi/Bluetooth/NFC module (SDIO/UART)
- ublox ZOE-M8Q GPS
- LSM9DS1 9-DOF IMU
- 1x 1-lane miniPCIe socket with USB 2.0
- Gateworks System Controller
- Audio jack with TLV320AIC Audio Codec, Speaker AMP
and TSA227E Headphone detect
- MAX8607 3-mode LED camera flash
- DECT ULE module
- FUSB302 USB-C PD and ISL9238 Battery charger
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Do not setup I2C3 in the SPL for Ventana as some devices on that bus
(aic3x codecs) can hang the bus causing i2c_setup to spin endlessly until
they are put into reset. Removing the setup of I2C3 from the SPL allows
the board-specific GPIO to be configured to take care of putting codecs
in reset prior to U-Boot setting up I2C3.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The only UART that is garunteed on Ventana boards is UART2 (serial-console).
Remove UART1 pinmux as that it is not consistent across all Ventana boards
and U-Boot doesn't need it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Rely on the phy-reset-gpios which is set in imx6qdl-sabresd dtsi
and get rid of the enet reset gpio handling from the board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabresd board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabreauto board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add the DM_GPIO related config for mx6sabreauto.
Also add the gpio request calls.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add the DM_GPIO related config for mx6sabresd.
Also add the gpio request calls.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This matches one of the following three boards (or fails):
- imx6q-sabreauto
- imx6qp-sabreauto
- imx6dl-sabreauto
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This matches one of the following three boards (or fails):
- imx6q-sabresd
- imx6qp-sabresd
- imx6dl-sabresd
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
distro boot expects that fdtfile name is setup for alternative DTB.
Create this file based on the first platform compatible string.
This should ensure that one rootfs can store multiple DTBs for different
boards.
Reflect structure which is used in Linux kernel. It means dtbs are
strored in xilinx folder.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Add Raspberry Pi Compute Module 3+ to list of models, the revision code
is 0x10 according to the list on raspberrypi.org.
v2: Use the same dtb name as CM3 as CM3+ is a drop in replacement
for CM3.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Ethernet has been broken for some time. This patch unifies
this board with a few others that use a similar approach to
enabling phy. This fixes ar8031 Ethernet controller so it works.
Signed-off-by: Adam Ford <aford173@gmail.com>
All platforms are converted to DM_I2C that's why there is no reason to
keep this code here.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Update boot_targets based on bootmode to run corresponding
distroboot command first.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is much easier to point to eeprom which stores information like MAC
address directly via DT. eeprom which contains this information is
pointed by /chosen/xlnx,eeprom parameter.
For example:
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
+ xlnx,eeprom = &eeprom;
};
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq and ZynqMP are sharing similar code and there is no reason to do
code duplication. Move zynq_board_read_rom_ethaddr() to common file for
easier conversion to DM.
Use ZynqMP version that's why also add CONFIG_ZYNQ_EEPROM_BUS to Syzygy
which is only one Zynq board which is using this feature.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
MV_DDR_FREQ_SAR lets the DDR frequency be determined by hardware
strapping. This also has the side effect of running the DDR clock in
synchronous mode with the CPU core clock rather than from an independent
PLL. We've seen this improve reliability in operation across a number of
boards and temperature ranges.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
Now that these boards use driver model we can drop the old code. At
present s5p_mmc_init() is still used by goni and smdkv310 so cannot be
removed unless we remove those boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This function is not needed now since the audio codecs have been converted
to proper drivers. The codec-enable GPIO is handled there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
At present the model is shown twice, once in the generic code and once
in the exynos code. Drop the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The TPS62517 PMIC driver has been partially converted to DM, so the
legacy I2C access layer isn't needed anymore.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Change maintainers to Prabhakar Kushwaha for fsl-qoriq, mpc85xx
and mpc86xx.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch moves the Armada XP video / LCD driver to DM_VIDEO. With this
move, the legacy interface board_video_init() is removed from the
theadorable board code (only user of this video driver). The support
via DT will be added in a separate patch.
This patch also enables DM_VIDEO for the theadorable board, as this is
needed to not break git bisect'ability.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This adds initial support for micro-DPU (uDPU) board which is based on Armada-3720 SoC.
micro-DPU is the single-port FTTdp "distribution point unit" made by Methode Electronics
which offers complete modularity with replaceable SFP modules both for uplink and downlink
(G.hn over twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Luis Torres <luis.torres@methode.com>
Cc: Scott Roberts <scott.roberts@telus.com>
Cc: Paul Arola <paul.arola@telus.com>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcVG0IAAoJECaAFcEOcohNKVAIAJd3DN/qudcVQdkuvAGK6WIk
Umxkm6rxHwur7oU+wxvK1p1l/0YTFBeCfo15quH1DkSc/WIUnmBlLmDvqpGVmPmh
ydZNE9ZChn0OKRIaM6pKJr+3p155cQDe6Mgg2j/5CnNx28KxT+vu7EqZbZvbQPag
wcZEK6Z6E5jMVHVn2lbLgmsBPmY7ksX168IqpvzTxIj0a4J3n0DcJUnO4RBBS0Q2
PGEvFhTvigVWs6r6GL0gLn3VwnQX30xQlIuKKORPcdhjk97cJcS4+bRxdTENTKD9
j3+pgyl1n04O8sPONZS7pH3fvJwtC6SwnoxTYxGrvjedw1LxbyHG3cqcGDg/TJ8=
=ik3X
-----END PGP SIGNATURE-----
Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchip
u-boot-rockchip changes for 2019.04-rc1:
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
This adds a MAINTAINER entry for chromebook_speedy.
Without this, we get the following warnings from the maintainers
check:
WARNING: no status info for 'chromebook_minnie'
WARNING: no maintainers for 'chromebook_minnie'
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Bob is a 10-inch chromebook produced by Asus. It has two USB 3.0 type-C
ports, 4GB of SDRAM, WiFi and a 1280x800 display. It uses its USB ports
for both power and external display. It includes a Chrome OS EC
(Cortex-M3) to provide access to the keyboard and battery functions.
Support so far includes only:
- UART
- SDRAM
- MMC, SD card
- Cros EC (but not keyboard)
Not included:
- Keyboard
- Display
- Sound
- USB
- TPM
Bob is quite similar to Kevin, the Samsung Chromebook Plus, but support
for this is not provided in this series.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add mention of a prerequisite needed to build the image. Also adjust the
English wording in a few places.
Ideally this should move to using binman to produce images, and avoid the
manual steps.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds support for the ASUS C201, a RK3288-based clamshell
device. The device tree comes from linus's linux tree at
3f16503b7d2274ac8cbab11163047ac0b4c66cfe. The SDRAM parameters
are for 4GB Samsung LPDDR3, decoded from coreboot's
src/mainboard/google/veyron/sdram_inf/sdram-lpddr3-samsung-4GB.inc
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
port the am335x based shc board to DM, to get rid
of DW warnings when compiling U-Boot.
- remove uneccessary board code
- adapt defconfigs
- remove unneeded defconfigs
configs/am335x_shc_prompt_defconfig
configs/am335x_shc_sdboot_prompt_defconfig
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
add u-boot specific am335x-shc-u-boot.dtsi file,
in which we add u-boot specific adaptions.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
add DTS from linux tree commit
"47bfa6d9dc8c060bf56554a465c9031e286d2f80"
change for U-Boot:
switch to SPDX-license identifier.
Signed-off-by: Heiko Schocher <hs@denx.de>
When power cycle the Jaguar2 boards, it couldn't read the
phys, therefore it always deduce that the board type is
pcb111.
Add a small delay after setting the gpio pins, fix the
issue.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Enabling DM_MMC skips the call to mmc_pinmux_setup() in board.c, as this
is supposed to be handled by the MMC driver, using DT information.
However we don't have a pinctrl driver yet, but would still like to keep
the working pinmux setup for our MMC devices. So bring this particular
call back to the DM_MMC code flow.
When booting from either SD card or eMMC, the SPL does the setup for us,
but when booting from SPI or USB we must not skip this part.
Fixes, boot via FEL or SPI flash, where the SPL won't setup the pinmux
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[jagan: add Fix details on commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch enables Falcon Mode by default and updates the README
file to show instructions on how to run from the micro SD card
or eMMC. This patch also enables fatwrite to help assist with
writing the 'args' to the microSD card.
Signed-off-by: Adam Ford <aford173@gmail.com>
The i.MX6 SOM and development kits have undergone significant
updates and changes over the past few months. This re-sync's
the U-Boot with Logic PD's BSP.
Signed-off-by: Adam Ford <aford173@gmail.com>
The MMC booting wasn't previously fitting into the codespace.
This patch enables MMC booting from the baseboard by reducing
some DM overhead during SPL.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch converts the warp7 and warp7_bl33 board ports over to using the
DM PMIC model.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
There is no need to set the ARCH variable when building U-Boot. In fact,
the ARCH name in U-Boot is 'arm'.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Enable SPL for i.MX8QXP MEK, and currently use SPL FIT.
The SPL enable SPL_DM to use MMC/PINCTRL/POWER DOMAIN/CLK.
Note: SPL FIT could not support secure boot chain, because i.MX8/8X
only support i.MX container format. This container format has
not been upstreamed, so we use FIT for now. When SPL container
supported, we could switch to that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In preparation of adding CONFIG_DM_MMC support use separate device
trees for raw NAND and eMMC devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
We have converted mmc to driver model on Poplar. So let's clean up
board level mmc initialization code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The miamiplus can use GEM0 through MIO pins, which requires a 125 MHz TX
clock to be generated. With the IO PLL at 1200 MHz this isn't possible, so
change it to run at 1000 and adjust the divisors accordingly. Also set the
GEM0 clock source to MIO instead of EMIO.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The miamiplus contains a speedgrade-2 device, which may run the CPU at 800MHz.
Change the PLL setting to 800MHz, and adapt the setpoints in the devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patches renames sd nodes in dts to be in line with
kernel. This patch also modifies the references for the same
in code.
It checks mmc first to have no time penalty for new DT node names based
on left-to-right expression evaluation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add board support and configuration for Jaguar2 SoC family.
The detection of the board type is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add board support, configuration and DTS for Servalt SoC
family. Currently there is one board in this family.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
On some ocelots platform a workaround is needed in order to be able to
reset the switch without resetting the DDR.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
These macros are not used anywhere in the boards code.
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Use get_ram_size to determine if the RAM size on Turris Mox is 512 MiB
or 1 GiB.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for reading One-Time Programmable memory via mailbox, which
communicates with CZ.NIC's firmware on the Secure Processor (Cortex-M3)
of Armada 3720.
Display product serial number and additional info, and also set MAC
addresses.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Check if Mox modules are connected in supported mode, then configure
the MDIO addresses of switch modules.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
When SFP module is connected directly to CPU module we want the SGMII
lane speed at 1.25 Gbps.
This is a temporary solution till there is a comphy driver in the kernel
capable of changing SGMII speed at runtime.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Restructure the board initialization source.
Remove the module_topology environment variable since it won't be
needed.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis-devboard target to dtb makefile
- add dtsi file for Neutis N5 needs
- add config file for Neutis N5 Dev board
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: update proper commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE.
However even the controller is enabled, the mux for the pins
are not set.
This patch follows the existing mux method. Since the pads are
different, separate check is added for each i2c.
Tested with A64-SOM204 board.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
am43xx_evm_ethboot_defconfig is not being actively used and has not been
moved to DM or DT. Also, ethboot cannot be tested on AM43xx EVM as such
due EVM limitations. Therefore delete it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These defconfigs don't seem be actively used any more, and have not been
moved to adapt DM or DT. Therefore delete them.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
bananapi r2 can be booted from sd-card and emmc
saving the environment have to choose the storage
from which the device has booted
also the offset is set to 1MB to make sure env is written
to block "user data area" between uboot and first partition
https://www.fw-web.de/dokuwiki/lib/exe/fetch.php?cache=&media=bpi-r2:boot-structure.png
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
u-boot makes a fixup for LS1046AQDS board to setup the properties
'fixed-link' and 'phy-connection-type' to 'xgmii' but in case of
backplane mode this fixup is not correct because it causes the KR link
to fail and so it must be bypassed in order to keep the link in KR
mode as it is defined in DTS.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
[YS: Fix compiling warning]
Reviewed-by: York Sun <york.sun@nxp.com>
fsl-mc lazyapply command applies dpl from efi_exit_boot_services().
Status of fsl-mc node in working fdt is updated at this stage.
However, an efi application like grub may already have copied the fdt.
So the updates to fdt done at efi_exit_boot_services() may not be
visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply
command is used.
Fixes: b7b8410a8f (ls2080: Exit dpaa only right before exiting U-Boot)
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add board support and configuration for Jaguar2 SOC family.
The detection of the board type in this family is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'ocelot' pcb123 and pcb120.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'luton' SoC.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
As we are moving to multi-dtb and board detection, remove static board
config options, and introduce board probing instead.
Luton: This add single-binary support for the two MSCC luton-based
reference boards - pcb090 and pcb091. The SoC chip ID is used to
determine the board type.
Ocelot: This add single-binary support for the two MSCC ocelot-based
reference boards - pcb120 and pcb123. The PHY ids on specific ports
are used to determine the board type.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
The IGEP0032 board was never officially pushed upstream and actually I
don't have access to this hardware, unless someone with the hardware
wants to start working on this doesn't makes sense have this defconfig
here. So remove it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
It enables DWC2 OTG gadget driver support for Poplar board. As
usb2_phy_init() is being always called from board_init(), we can save
the call from board_usb_init().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit 3f353ceccb ("vf610: refactor DDRMC code") changed on-die
termination (ODT) values from 120 Ohm to 60 Ohm and enabled a static
read/write leveling which has not been tested with this board. This
commit reverts both changes and makes sure that memory gets
initialized as it has been done before the mentioned commit.
Fixes: 3f353ceccb ("vf610: refactor DDRMC code")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
I can't continue maintaining the board because I don't have access to the
hardware anymore, so remove myself from the entry and add Javier who has
volunteered to help and maintain the board.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Javier Martínez Canillas <javier@dowhile0.org>
