This device tree adds support for DHCOM iMX6 duallite and solo
deriviates.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
To use the device tree definitions imx6q-dhcom-som.dtsi for all imx6 derivatives rename
it to imx6qdl-dhcom.dtsi. We omit the '-som', because it simplifies further mainlinening
of already existing device trees.
To reuse board level common stuff imx6qdl-dhcom-pdk2.dtsi is created and included by
imx6q-dhcom-pdk2.dts.
Signed-off-by Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: output: 1 [x] dbg1.gpios
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This file setups UART5 based serial to be used as pre-relocation
console in the U-Boot proper.
On purpose pinux configuration is omitted here as it has been already
done in SPL. For early pre-relocation code we only need the serial
device from DTS.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit ports from Linux kernel - tag: v5.1 - the device tree
description for display5 board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Those properties are U-Boot specific as the mxs gpio Linux driver (up to
version v5.1.11) is not supporting them.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch copies from the Linux kernel stable (tag v5.1.11)
SHA1: 17bb763e7eaf i.MX28 related device tree files.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Let the board continue boot from the storage device where
it bootup.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
RK3399 use sdhci for eMMC and DW MMC for SD Card, and
spl will only try to boot from SDMMC if we don't specify
other boot device for spl-boot-order. So add sdhci and sdmmc
for spl-boot-order here.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the dts files for the Rock960 boards from Linux to get the
latest changes and fixes for the devices.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
The timer0 node has its two clocks written in reversed order. The timer0
is used as the tick timer which causes a problem that the time a delay
function used is 4 times longer.
This patch reverses these two clocks to solve this issue.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The AM654 base board has a TCA9554/PCA9554-type GPIO expander on the
wkup_i2c0 bus at address 0x38 that is used to detect the presence of
daughter cards. Add a respective DTS description of this expander
to enable its use.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
To enable the use of an EEPROM-based board detection scheme we need to
be able to access the I2C bus associated with the EEPROMs across all
3 stages of U-Boot: R5 SPL, A53 SPL, and A53 U-Boot (proper). So go
ahead and add/update the wkup_i2c0 peripheral module DTS definitions
and its associated pinmux node accordingly.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Only U-Boot specifc DT properties or overrides, must be in -u-boot.dtsi.
Pinctrl nodes does not belong here. Now that pinctrl nodes are in kernel
DT, there is no reason to be keep these in -u-boot.dtsi. Move them to
proper places so that it would ease copying DT entries from kernel DT.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
With changes in the driver requiring phy related properties,
add the same for the SD card node to prevent breaking boot with
the driver update.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync the sdhci0 node from kernel. This changes the compatible that is
required to be there in the driver. Change the same for the SD card node
which is not yet supported in kernel. This also syncs the main_pmx0 node
as a side effect.
Also change the name of the driver to match the compatible in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add mcu cpsw and its components along with scm_conf node
to have ethernet functional.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Since we have limited resources in SPL, it is the best interest
to keep the SPL as small as possible and that includes the DTB.
There are a few items in the device tree that can be removed,
because these boards don't use them.
Signed-off-by: Adam Ford <aford173@gmail.com>
The MMC card-detect pin was incorrectly defined which was fixed.
This patch resync's the dts and removes the u-boot specific fix.
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.
The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.
Signed-off-by: David Lechner <david@lechnology.com>
Since pinctrl_stm32 driver update, each gpio bank is now binded
by pinctrl driver. The compatible string "st,stm32-gpio" becomes
useless, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Synchronize device tree with v5.2-rc4 label and
update the associated u-boot dtsi.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Add IPCC mailbox support on stm32mp157 eval and disco boards.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- SPL SATA enhancements to allow booting from RAW SATA device
needed for Clearfog (Baruch)
- Enable SATA booting on Clearfog (Baruch)
- Misc changes to Turris Omnia (Marek)
- Enable CMD_BOOTZ and increase SYS_BOOTM_LEN on crs305-1g-4s
(Luka)
- Enable FIT support for db-xc3-24g4xg (Chris)
- Enable DM_SPI on Keymile Kirkwood board with necessary changes
for this (Pascal)
- Set 38x and 39x AVS on lower frequency (Baruch)
In order to migrate the SPI flash interface to the driver model, the SPI
configuration needs to be added in the KM Kirkwood device tree file.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable SATA peripherals in SPL to allow boot from SATA.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
[ Linux commit aa38571246c6ac279ebebd141157297bcb959d76 ]
The memory regions specified by /memreserve/ are passed to
early_init_dt_reserve_memory_arch() with nomap=false, so it is
not suitable for reserving memory for Trusted Firmware-A etc.
Use the more robust /reserved-memory node with the no-map property
to prevent the kernel from mapping it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix the following:
- use "jedec,spi-nor" binding, we use jedec compatible flashes
- set bus width to 4, we use quad capable flashes
- differentiate bewteen data and clk and cs pins
- drop partions as we don't use them in u-boot.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com: use "jedec,spi-nor", edit commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
After the transition to DM, only the mx6dl/solo wandboard
is supported.
Add FIT image support so that all the wandboard variants
can be supported, like it was prior to the DM conversion.
Successfully booted Linux on mx6q/solo/qp wandboards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Place dtbs under SoC level rather than board level.
imx6q-novena.dtb and imx6dl-wandboard-revb1.dtb were
placed under the board config option, so move them
to SoC level.
This also aligns with the kernel dts Makefile format.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
rockchip pinctrl driver has update to use dts, so we need
to add the pinctrl config in SPL for sdmmc.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Migrate all the "u-boot,dm-pre-reloc" tag from rk3288-tinker.dts
into rk3288-tinker-u-boot.dtsi.
When both board level and soc level '-u-boot.dtsi' files exist,
we need to include the soc level 'rk3288-u-boot.dtsi' manually.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
As in stm32f7-u-boot.dtsi these nodes already have "u-bootdm-pre-reloc"
property, no need to add them again in stm32f746-disco-u-boot.dtsi.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Import iMX53 M53Menlo device tree from Linux next-20190607 3f310e51ceb1 .
Enable DT control in full U-Boot . Add U-Boot extras into separate DTSi,
the GPIO controllers need to be inited early, otherwise m53_set_clock()
won't be able to detect the correct CPU clock frequency by reading the
GPIO.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Synchronize iMX53 device tree from Linux next-20190607 3f310e51ceb1 ,
this is needed to get NFC, UART, USBOTG DT nodes.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
u-boot,dm-pre-reloc for uart0, uart2 indeed u-boot specific
properties. Move them into rk3399-u-boot.dtsi so the boards
which enabled these node will available during SPL.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3328-rock64.dts has been taken from Linux kernel commit
cff6d1d6f88b ("arm64: dts: rockchip: enable HS200 for eMMC on rock64")
with minor modifications (drop nodes not known by rk3328.dtsi).
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove the override for usbotg_hs on g-tx-fifo-size as the correct
binding, used in the kernel device tree, is now supported in dwc2
device driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
LS1028A includes an integrated PCI bus with 11 PCI functions residing on
bus 0. ECAM plus the device register space takes up 256MB of address
space.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch is to fixed the reg read to "0" for armv7
architecture.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch is to enable esdhc controllers for lx2160aqds
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Updating the bcm283x device tree sources adds the device trees for
- Raspberry Pi 3 Model A+
- Raspberry Pi 3 Model B+
- Raspberry Pi Compute Module IO board rev1
- Raspberry Pi Compute Module 3 IO board V3.0
- Raspberry Pi Zero
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2C9f
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot
- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
All i.mx6 boards seems to have moved to DM_USB, however gadget support
for mx6 is still pre-DM as CI_UDC isn't converted yet. To make this work
the usb otg controller used for gadgets needs to be usb number 0.
Add an alias for this directly in the main u-boot mx6qdl dtsi so it
doesn't need to be done for each board separately.
This fixes regressions wrt. usb gadget functionality in several boards
that have gadget functions enabled in their config, but no usb0 alias in
their device-tree.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Enable DM block and DM MMC support on iMX6SX VINING|2000 .
Convert board code to match the DM support. This disables
USB mass storage support due to missing DM USB, however
that will be re-enabled in subsequent patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Import iMX6SX VINING|2000 device tree from Linux 5.1.1 b724e9356404 .
Enable DT control in full U-Boot .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT
V1.0B module. Unlike the V1.0A early access samples exclusively booting
from SD card, they are now strapped to boot from eFuses which are
factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Gigabit Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QM as of yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Add support for i2c0, i2c1, i2c2, i2c3 and i2c4.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Add support for lpuart1, lpuart2, lpuart3 and lpuart4.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Enable DM block, DM MMC and DM SATA support on iMX6Q Novena
convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Import iMX6Q Novena device tree from Linux 5.1-rc7 37624b58542f .
Enable DT control in full U-Boot .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
The SPI nCS signal is active low, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Import DHCOM iMX6 PDK2 device tree from Linux 5.1.1 b724e9356404 .
Enable DT control in full U-Boot .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
This fixes an issue with USB host mode.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate USB to Driver Model (CONFIG_DM_USB=y).
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Add device tree to Makefile to avoid newly introduced error:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
make[1]: *** [dts/Makefile:28: arch/arm/dts/imx6-apalis.dtb] Error 1
make: *** [Makefile:1009: dts/dt.dtb] Error 2
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The bulk of these changes are an effort to unify Tegra186 builds with
builds of prior 64-bit Tegra generations. On top of that there are
various improvements that allow data (such as the MAC address and boot
arguments) to be passed through from early firmware to the kernel on
boot.
This patch adds independent watchdog support for stm32mp157c
in SPL.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the necessary configuration to have NAND and NOR support on ev1 board
for BASIC boot (with SPL) or for TRUSTED boot (with TF-A).
STM32MP> nand info
Device 0: nand0, sector size 256 KiB
Page size 4096 b
OOB size 224 b
Erase size 262144 b
subpagesize 4096 b
options 0x00184200
bbt options 0x00060000
STM32MP> sf probe
SF: Detected mx66l51235l with page size 256 Bytes, erase size 64 KiB, total 64 MiB
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support for Avenger96 board from Arrow Electronics based on STM32MP157
MPU. This board is one of the Consumer Edition (CE) boards of the 96Boards
family and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add an "ethernet" alias that points to the default network interface,
which is the built-in EQoS on Jetson TX2.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Recent versions of DTC have checks for PCI host bridge device tree nodes
that are named something other than "pci" or "pcie". Fix all occurrences
of such nodes for Tegra boards to avoid potential warnings from DTC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This allows SPL to load the main U-Boot image from MMC once DM_MMC is
enabled.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
- some fix for rk3399-puma;
- rockchip script make_fit_atf.py cleanup
- Enable TPL for rk3399 orangepi and nanopi4;
- add support for rk3399 boards: Nanopi NEO4, Rockpro64, Rock PI 4;
The following DT nodes in the process on review for Linux 5.3,
until Linux 5.3 is tagged, add the missing DT nodes in u-boot specific
DTSI files that will be dropped when the v5.3-rc1 DT is synced again.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add initial support for Rock PI 4 board.
Specification
- Rockchip RK3399
- LPDDR4
- eMMC
- SD card slot
- RTL8211E 1Gbps
- HDMI In/Out, DP, MIPI DSI/CSI
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type
Commit details of rk3399-rock-pi-4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: add ROCK Pi 4 DTS support"
(sha1: 1b5715c602fda7b812af0e190eddcce2812e5417)
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add initial support for Rockpro64 board.
Specification
- Rockchip RK3399
- 2/4GB Dual-Channel LPDDR3
- SD card slot
- eMMC socket
- 128Mb SPI Flash
- Gigabit ethernet
- PCIe 4X slot
- WiFI/BT module socket
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-rockpro64.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: rockpro64 dts add usb regulator"
(sha1: 6db644c79c8d45d73b56bc389aebd85fc3679beb)
'Akash' has sent an initial patch before, so I keep him as board
maintainer and I'm co-maintainer based on our conversation.
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Finding bitstream from cff-file is no longer valid after bitstream is built
into FIT image and loaded by generic firmware loader. Remove cff-file
as this is legacy implementation from A10 downstream.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Update DDR configuration with the latest update:
- PUBL_regs: DXnGCR[0]= according to ddr_width to disable Byte
lane 2/3 in 16bit
- fix LPDDR2/3 timing_calc to step RL/WL in relaxed
timings mode
- remove LPDDR3 RL3 (optional) support vs MR0[7]
because MR0[7] can't be read instead always apply
worse RL/WL for LPDDR3 when freq < 166MHz)
- change MR3 to 48ohm drive for LPDDR2/3
- change default ZPROG[7:4] = 0x1 for LPDDR2/3 ,
'0' is not allowed even when ODT not used
- use DQSTRN for LPDDR2/3 (it was not set in PIR)
- LPDDR3: set dqsge/dwsgx gate extension to 2,2
like LPDDR2
-DDRCTRL.dfitmg0:
+ for LPDDR3 tphy_wrlat = WL (as LPDDR2)
+ improvement for relaxed mode vs RL/Wl at corner case.
For example @533MHz RL/WL (relaxed) = 9/5 for LPDDR2/3
and correction to MR2 accordingly
- DDR_PCFGQOS1_1: port1 timeout relaxed from 0x00 to 0x40,
for LTDC.
- DDR_PCFGWQOS0_0: change vpr level from
11 to 12 in order to include the CPU on
the variable priority queue.
- DDR_SCHED: fix to consider 13 levels (13 levels - 1 = 0xC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXOK5Sw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXBvoAJ96YrInVKKWtuVigA9lNpk5xbmbeQCdG9wML4LI
dBbQyzD3mNqvnDMyNPQ=
=Plt7
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.07-rc3' of git://git.denx.de/u-boot-video
- update for using splashfile instead of location->name
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
Meet the following boot hang.
"
U-Boot SPL 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800)
Trying to boot from MMC1
U-Boot 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800)
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C)Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Smart Device Board
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
Video device 'ipu@2400000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Video device 'ipu@2800000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Some drivers failed to bind
Error binding driver 'generic_simple_bus': -28
Some drivers failed to bind
initcall sequence 4ffe4500 failed at call 1780dfb7 (err=-28)
"
1. fdtdec_get_alias_seq will use "video" as base, however in alias node,
we use ipux, so add new alias for U-Boot dts.
2. DM_VIDEO is enabled, however reserve_video is called before
relocation, so to make DM_VIDEO work before relocation, need to
set SYS_MALLOC_F_LEN
3. defconfig is updated with savedefconfig
Note: I do not have a video panel to test, but with this patch, U-Boot
boots up again, below log.
"
U-Boot SPL 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800)
Trying to boot from MMC1
U-Boot 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800)
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Smart Device Board
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3
Loading Environment from MMC... *** Warning - bad CRC, using default environment
PCI: pcie phy link never came up
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The ipu node in imx53 is needed for DM_VIDEO. We also need to set
u-boot,dm-pre-reloc to initialize before relocation.
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Without this U-Boot specific property, booting on Armada XP theadorable
fails in SPL. All nodes in the "internal-regs" (simple-bus) DT node are
not scanned, so the UART node is missing (and others).
I'm not adding this property in an *u-boot.dtsi file, since there is
none matching the generic rules for all files including this dtsi
file. So to not miss any of the boards using this dtsi file, I'm
adding it to this file directly, which makes the Linux merge a less
easy unforunately.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
The watchdog should use a clock at 50 Mhz, so
instead of using the clock osc (200 Mhz), we
define a reference clock at 50Mhz and use it
for both watchdog.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The watchdog should use a clock at 50 Mhz, so
instead of using the clock osc (200 Mhz), we
define a reference clock at 50Mhz and use it
for both watchdog.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Keep the FPGA bridge entries in SPL DT to let do_bridge_reset() toggle
the bridges on/off as needed according to the handoff file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Pull out the u-boot,dm-pre-reloc from socfpga_arria10_socdk_sdmmc_handoff.dtsi
into separate dtsi header file to make it easier to patch in custom handoff
dtsi files, without having to manually add the U-Boot bits. Shuffle the include
clauses in the A10 DT files to make it obvious what gets included where without
having to follow confusing long chain of includes, i.e. board DT file includes
everything it needs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Re-add support for Aries Embedded MCV SoM, which is CycloneV based
and the associated MCVEVK and MCVEVP baseboard. The board can boot
from eMMC. Ethernet and USB is supported.
The Aries Embedded boards have been removed with commit 03b54997d5
("board/aries: Remove"). I will now take care of them.
The device-tree files are from mainline Linux commit e93c9c99a629
("Linux v5.1)".
Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de>
CC: Marek Vasut <marex@denx.de>
CC: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add FPGA driver to support program FPGA with FPGA bitstream loading from
filesystem. The driver are designed based on generic firmware loader
framework. The driver can handle FPGA program operation from loading FPGA
bitstream in flash to memory and then to program FPGA.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Improvements and new features:
- split more rockchip pinctrl_core feature into per SoC
- enable TPL for evb-rk3399 board
- enable TPL/SPL for evb-px5 board
- enable TPL and OP-TEE support for evb-rk3229
- update fix in arm common assembly start code for rockchip header file
- update default SPL_FIT_GENERATOR for rockchip
- rk3399 boards update to use '-u-boot.dtsi'
- add new rk3399 boards: Nanopi M4, Nanopc T4
- enable sound for chromebook_minnie
Add initial support for Nanopc T4 board.
Specification
- Rockchip RK3399
- Dual-Channel 4GB LPDDR3-1866
- SD card slot
- 16GB eMMC
- RTL8211E 1Gbps
- AP6356S WiFI/BT
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-nanopc-t4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: Add NanoPC-T4 IR receiver"
(sha1: 95658e21b1707ad7844f873db2fdaa295109a5a3)
Tested-by: Daniel Gröber <dxld@darkboxed.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Attaching GPIO functionality to SDMMC0_DET pin (which
does in Linux base dts) make dwmmc driver "fail to detect
the card".
Card did not respond to voltage select!
It may be because the existing driver can't support gpio
card detection. So, change the pinctrl functionality from
RK_FUNC_GPIO to RK_FUNC_1 like other rk3399 dts does via
sdmmc_cd pin.
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This allows SPL to load the main U-Boot image from MMC once DM_MMC is
enabled.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and
like some of the other similar boards requires bin_hdr.
bin_hdr (DDR3 init stage) is currently retrieved from the stock
bootloader and compiled into the kwb image.
Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip
support and writing env to SPI flash.
Signed-off-by: Luka Kovacic <me@lukakovacic.xyz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit ff7bd212cb ("net: phy: micrel: fix divisor value for KSZ9031
phy skew") fixed the skew value divisor for the KSZ9031, but left the
code using the same divisor for the KSZ9021, which is incorrect.
The preceding commit c16e69f702 ("net: phy: micrel: add documentation
for Micrel KSZ90x1 binding") added the DTS documentation for the
KSZ90x1, changing it from the equivalent file in the Linux kernel to
correctly state that for this part the skew value is set in 120ps steps,
whereas the Linux documentation and driver continue to this day to use
the incorrect value of 200 that came from the original KSZ9021 datasheet
before it was corrected in revision 1.2 (Feb 2014).
This commit sorts out the resulting confusion in a consistent way by
making the following changes:
- Update the documentation to be clear about what the skew values mean,
in the same was as for the KSZ9031.
- Update the Micrel PHY driver to select the appropriate divisor for
both parts.
- Adjust all the device trees that state skew values for KSZ9021 PHYs to
use values based on 120ps steps instead of 200ps steps. This will result
in the same values being programmed into the skew registers as the
equivalent device trees in the Linux kernel do, where it incorrectly
uses 200ps steps (since that's where all these device trees were copied
from).
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Olimex A64-Teres-I board is a mainboard (the only one so far)
for Olimex Teres-I DIY laptop kit.
Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- MicroSD Slot
- 16GB eMMC Flash
- eDP LCD display
- HDMI
- USB Host
- Battery management
- 5V DC power supply
- Certified Open Source Hardware (OSHW)
Works:
- i2C
- MMC/SD
- PWM backlight
Known broken:
- Internal keyboard (seems to be because the keyboard firmware loads a
bootloader first, and then disconnects bootloader and connect real
keyboard). External ones connected to the USB port work fine.
This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).
Linux commit details about the sun50i-a64-teres-i.dts sync:
"arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins"
(sha1: d91ebb95b96c8840932dc3a10c9f243712555467)
Cosmetic warnings regarding whitespace and placement of SPDX notice for
dts file was ignored.
config and .dtsi file are adapted from pinebook files.
Tested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: move board entry in MAINTAINERS file at proper position]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync rk3399-nanopi4.dtsi from Linux 5.1-rc2 tag.
Linux commit details about the rk3399-nanopi4.dtsi sync:
"arm64: dts: rockchip: Add nanopi4 bluetooth"
(sha1: 3e2f0bb72be36aa6c14ee7f11ac4dd8014801030)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To make successful build with dts(i) files syncing from Linux 5.1-rc2
the rk3399.dtsi would require pwm2_pin_pull_down.
So, sync the pwm2_pin_pull_down node from Linux 5.1-rc2. Since this
node is strictly not part of any commit alone, I have mentioned
Linux 5.1-rc2 tag for future reference of where would this sync
coming from.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Now we have
- board specific -u-boot.dtsi files for board specific u-boot
dts changes.
- soc specific rk3399-u-boot.dtsi for soc specific u-boot
dts changes.
So, include the rk3399-u-boot-dtsi on respective board -u-boot.dtsi
and drop the properties which are globally available in rk3399-u-boot.dtsi
Right now rk3399-u-boot.dtsi has sdmmc, spi1 u-boot,dm-pre-reloc
property and more properties and nodes can be move further based
on the requirements.
This would fix, the -u-boot.dtsi inclusion for evb, firefly, puma
boards that was accidentally merged on below commit.
"rockchip: dts: rk3399: Create initial rk3399-u-boot.dtsi"
(sha1: e05b4a4fa8)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add u-boot,dm-pre-reloc property for spi1, so-that the
subsequent rk3399 boards which boot from SPI.
This help to separate the u-boot specific properties away
from base dts files so-that the Linux sync become easy and
meaningful.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Devicetree files in RK3399 platform is synced from Linux, like other
platforms does. Apart from these u-boot in rk3399 would also require
some u-boot specific node like dmc.
dmc node has big chunk of DDR timing parameters which are specific
to specific board, and maintained with rk3399-sdram*.dtsi.
So, create board specific -u-boot.dtsi files and move these sdram dtsi
files accordingly. This would help of maintain u-boot specific changes
separately without touching Linux dts(i) files which indeed easy for
syncing from Linux between releases.
These board specific -u-boot.dtsi can be extendible to add more u-boot
specific nodes or properties in future.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Sometimes u-boot specific dtsi files are included
automatically which would build for entire rockchip SoC,
even-though the respective dtsi should used it for specific
family of rockchip SoC.
- Sometimes u-boot specific dts nodes or properties can use
config macros from respective rockchip family include/configs
files, example CONFIG_SPL_PAD_TO.
So, it's better to compile the dtbs based on the respective
rockchip family types rather than rockchip itself to avoid
compilation issues.
This patch organize the existing dtb's based on the rockchip
family types.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable sound for this board, which has the same codec as jerry.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
TPL need dmc to init ddr sdram, and emmc, boot-order.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Add board code and DTs for Renesas RZ/A1 SoC-based GR-Peach,
which is a cheap development platform with RZ/A1H SoC. The
DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Currently supported are UART, ethernet and RPC SPI. The board
can be booted from RPC SPI by writing the u-boot.bin binary
to the beginning of the SPI NOR, e.g. using the "sf" command.
The board can also be booted via JTAG by setting text base to
0x20020000, loading u-boot.bin there via JTAG and executing it
from that address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add platform code and DTs for Renesas RZ/A1 R7S72100 SoC.
Distinguishing feature of this SoC is that it has up to
10 MiB of on-SoC static RAM (SRAM).
The DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As mx66l512 qspi flash supports quad input fast program and
quad input fast read, set spi-tx_bus-width and spi-rx_bus-width
to 4.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As n25q128 qspi flash supports quad input fast program and
quad input fast read, set spi-tx_bus-width and spi-rx_bus-width
to 4.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As n25q512a qspi flash supports quad input fast program and
quad input fast read, set spi-tx_bus-width and spi-rx_bus-width
to 4.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The card detect pin was incorrectly using IRQ_TYPE_LEVEL_LOW
instead of GPIO_ACTIVE_LOW when reading the state of the CD pin.
Without this patch, MMC1 won't be detected.
This is the same patch submitted to linux-omap, but I was hoping
to get it applied to U-Boot without having to wait for the
linux adoption and then backporting.
Fixes: 5448ff33f2 ("ARM: DTS: Resync Logic PD SOM-LV 37xx
devkit with Linux 4.18-RC4")
Signed-off-by: Adam Ford <aford173@gmail.com>
Add device-tree files from linux 5.1-rc7 needed to complete support
for PocketBeagle.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Transition to the IOPAD macros as used in Linux in which the pin mux
mode is specified using a dedicated parameter while also dropping the
related MUX_MODEx macros that are no longer needed. This transition
will allow us to keep both Linux and U-Boot DTS in sync more easily.
While at it also align the file name of the include file itself and
update any references accordingly.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
- at91sam9g20-taurus.dts: use labels
- cleanup taurus port to compile clean with
current mainline again. SPL has no serial
output anymore, so it fits into SRAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Switch from using the high priority DMSC transmit message queue used
by the secure R5 MCU island boot context to the low priority message
queue. While the change in priority is irrelevant for the current boot
architecture it however gives us access to a deeper message queue that
will allow us to buffer more messages. This is an important aspect when
sending several messages without requesting and waiting for a response
in a row which is a communication scheme used during core shutdown for
example. See AM654 TISCI User Guide for additional details.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
-----BEGIN PGP SIGNATURE-----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=CzWQ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
u-boot,dm-pre-reloc is required for SDMMC booted rk3399 boards and
which is U-Boot specific devicetrees binding.
Move it on global rk3399-u-boot.dtsi file and rest of the U-Boot
bindings will move it future based on the requirement.
This would help to sync the devicetrees from Linux whenever required
instead of adding specific nodes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sync rk3399-opp.dtsi from Linux.
Linux commit details about the rk3399-opp.dtsi sync:
"arm64: dts: rockchip: use SPDX-License-Identifier"
(sha1: 4ee99cebd486238ac433da823b95cc5f8d8a6905)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Booting this board failed as the initial console isn't found since
commit c402e81702 ("dts: arm: socfpga: merge gen5 devicetrees from linux")
The uart0 devicetree entry was missing "clock-frequency = <100000000>:"
since that commit
Fixes: c402e81702 ("dts: arm: socfpga: merge gen5 devicetrees from linux")
Reported-by: rafael mello <rafaelmello_3@hotmail.com>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add the device trees for
* vexpress_ca5x2_defconfig
* vexpress_ca9x4_defconfig
* vexpress_ca15_tc2_defconfig
as available in Linux 5.1 rc5.
We are using the vexpress_ca15_tc2_defconfig and vexpress_ca9x4_defconfig
for Travis testing via QEMU.
The UEFI base Embedded Base Boot Requirements Specification (EBBR) requires
that an embedded board either provides a device tree or an ACPI table.
All block devices are meant to be moved to the driver model. On ARM this
requires a device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is Marvell's Kirkwood development board. It has the following
features
- 512M DDR2
- 2 PCI connectors
- 1 x1 PCI-e interface
- 1 Gigabit Ethernet Port
- 2 SATA Ports
- USB 2.0 Interface
- SDIO
- 128M NAND Flash
- 16M SPI Flash
It can be strapped to boot from SPI or NAND so there are two defconfigs
(one per boot media).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The following Kirkwood dtb build targets are currently missing:
kirkwood-openrd-base.dtb
kirkwood-openrd-client.dtb
kirkwood-openrd-ultimate.dtb
This patch adds them to the Makefile to fix the build error.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit switches to DM USB for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This commit switches to DM SERIAL for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Fix compatible node to use regular Toradex notation.
Annotate device tree with standard Colibri pin muxing comments.
Use open-drain I2C pin muxings.
Alphabetically re-order iomuxc nodes.
Rename snvs-ad7879-int-grp touch interrupt node as per Linux device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also fix indentation of pinfunc header file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add support for lpuart1, lpuart2 and lpuart3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch imports the Linux kernel base board imx7d-pico.dtsi,
pi board imx7d-pico-pi.dts and hobbit board imx7d-pico-hobbit.dts
from Linux v5.1-rc1.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Migrate Ethernet FEC to using driver model.
Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate USB to using driver model.
Add USBH_PEN GPIO regulator.
While at it also add alias e.g. as required for UMS.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The implicit fallback mechanism for searching the whole MDIO bus for at
least one PHY has been gone with the following commit b882005a18
("drivers/net/fec: phy_init: remove redundant logic"). This lead to the
Ethernet driver erroring out as follows:
Net: Could not get PHY for FEC0: addr -19
eth-1: fec@400d1000
Colibri VFxx # dhcp
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
No ethernet found.
Could not get PHY for FEC0: addr -19
Colibri VFxx #
This commit adds an explicit PHY node which makes it work again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This commit enables the support for K&P's HSC|DDC imx53 based boards.
It was also necessary to provide device tree description for regulators
to avoid board specific code definition.
The GPIO pin description responsible for VBUS control has been moved from
"hog" group to usbh1 dedicated one.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This code has been ported from Linux kernel - tag v5.1-rc2.
The difference from the kernel is the removal of:
fsl,usbmisc = <&usbmisc 1>;
fsl,usbphy = <&usbphy1>;
properties, which are not needed for correct u-boot operation (as PHY
setup is done in ehci-mx5.c file itself).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
In this commit the esdhc3 controller is enabled as well as it is remaped
to mmc0 to not break legacy code.
The pinctrl setup (e.g. 0x1e4) is the same as one from in-board file
definition.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for MediaTek MT8516 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The 'phy' reset of gmac device in kernel device tree is not generic
enough for u-boot to use, so we need to overwrite the 'resets' property
as needed. With this device tree fixup and poplar_defconfig changes,
Ethernet starts working on Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As U-boot stm32f clock driver doesn't support new
bindings for auxiliary clocks (clocks = <&rcc 1 ....>),
restore old bindings for usart1 to get console output.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Synchronize stm32h7 device tree with kernel v4.20.
U-boot DT files and pinctrl bindings are updated,
useless nodes are removed and gpio compatible added.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to prepare and ease future DT synchronization with kernel
DT, migrate all U-boot specific nodes/properties/addons to
U-boot DT files.
As sdmmc is not yet supported on kernel side, sdmmc nodes
are located in eval-u-boot and disco-u-boot DT files.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to prepare and ease future DT synchronization with kernel
DT, migrate all U-boot specific nodes/properties/addons to
U-boot DT files.
Migrate also DT nodes which are not yet available on kernel DT side
as ethernet, ltdc and qspi nodes.
Fix ethernet_mii pins and add missing qspi_pins for stm32746g-eval
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Import Linux 5.1-rc1 DT from 9e98c678c2d6 ("Linux 5.1-rc1") for the
meson-g12a-u200 board, the meson-g12a.dtsi and the corresponding bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvW07AAoJEB6zHgIOrC/Iu4QH/1REDOTrsZPydd2yD/O81vPs
RiLC8wP2J4UmqtMcNTLyvxlYwrzqoR5J6SYdyBNU/+cLEp/gdzEI+rjsfSV2uRX1
Qb4Pk2FiI503JVjegxsbJqzASfiEP7rIg3HM5431xbhYH22MW2FH6le6yrtNxjBh
m1WFjQYX1bpbGb6zue8TgyLIeN1IqWuqnH9kUHixUEan+xrpEhN239LDFjdvGbvC
BvYyMtDddmMt4YDzNjgX36us993kylGZp6JijR3zgUao7I/JGVZAJrxw8MHDTnVy
UKv3VI9F5bGLSvzqTVL2MFU6XtJW26v+niGLhGzlUhb3TTKrdKOicm3VF7tO+JU=
=MamK
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-b' of git://git.denx.de/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2019.07 cycle
The DK1 and DK2 boards use the USB Type-C controller STUSB1600.
This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller
to check cable detection.
- the DWC2 driver to support a new dt property
"u-boot,force-b-session-valid" which forces B session and
device mode; it is a workaround because the VBUS sensing and
ID detection isn't available with stusb1600.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Use the DWC2 device driver with DM_USB_GADGET support and
cleanup the USB support in STM32MP1 board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
Linux commit details about the sun50i-h6-beelink-gs1.dts sync:
"arm64: dts: allwinner: h6: Introduce Beelink GS1 board"
(sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193)
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SAMA5D2 ICP Board features the SAMA5D27 SoC,
together with QSPI Flash, Wilc3000 wireless device and
EtherCat support.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Merge qspi dts node from Linux.
Commit 0cb140d07fc75fb (arm64: dts: stratix10: Add QSPI support for Stratix10)
Add -u-boot.dtsi files for non Linux dts properties and
update properties for Uboot.
- add u-boot,dm-pre-reloc
- add alias for spi0
- change compatible for flash
- support quad read and quad write
- change maximum frequency to 100MHz
Tested on Stratix 10 SoC devkit.
SOCFPGA_STRATIX10 # sf probe 0:0
SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
The stratix10 socdk ships with 4GB of memory. Modify the
device tree to represent this. Note that to access 4GB of
memory in Stratix 10, due to the IO space from 2GB to 4GB,
we use the fact that the DDR controller ignores upper address
bits outside of the configured DRAM's size. This means that
, the 4GB DRAM is mapped to memory every 4GB.
For an 8GB memory, you can either live with the 2GB IO space,
and loose access to that memory from the processor, or use
the same trick:
Loose 2GB of memory:
memory {
device_type = "memory";
/* 8GB */
/* first 2GB */
reg = <0 0x00000000 0 0x80000000>,
/* last 4GB */
<1 0x00000000 1 0x00000000>;
u-boot,dm-pre-reloc;
};
or to map it all:
memory {
device_type = "memory";
/* 8GB */
/* first 2GB */
reg = <0 0x00000000 0 0x80000000>,
/* next 6GB */
<2 0x80000000 1 0x80000000>;
u-boot,dm-pre-reloc;
};
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
To clean up reset handling for socfpga gen5, port the DDR driver to DM
using UCLASS_RAM and implement proper reset handling.
This gets us rid of one ad-hoc call to socfpga_per_reset().
The gen5 driver is implemented in 2 distinct files. One of it (containing
the calibration training) is not touched much and is kept at using
hard coded addresses since the code grows even more otherwise.
SPL is changed from calling hard into the DDR driver code to just
probing UCLASS_RESET and UCLASS_RAM. It is happy after finding a RAM
driver after that.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The SPL for socfpga gen5 currently takes all peripherals out of reset
unconditionally. To implement proper reset handling for peripherals,
the reset node has to be provided with the SPL dts.
In preparation to move the DDR driver to DM, the sdr node is required
in SPL, too.
This patch adds "u-boot,dm-pre-reloc" to U-Boot specific dtsi addon
files so that the reset manager and SDR driver correctly probe in SPL.
It centralizes these settings into a common file since in contrast to
boot-type specific nodes, "soc", "rst" and "sdr" are always needed.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This is again a sync to linux-next + pending patches in Dinh's tree at
commit 1c909b2dfe6a ("ARM: dts: socfpga: update more missing reset
properties")'
It adds missing peripheral reset properties to socfpga.dtsi and removes
U-Boot specific leftovers from socfpga_cyclone5_socrates.dts.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly262oACgkQykllyylKDCH44gCbBnuxUH6ZF0B7Leuee4te7C59
LmUAn14/bbtMt17zkMSADCjY9yGWF4au
=mWrW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze
Xilinx/FPGA changes for v2019.07
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
Enable ahci node for BPI-M2-Berry, this would require since
we have DM_SCSI enabled on the respective SoC.
Unable to sync the same node from Linux, since the similar change
is still in Linux ML.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for a20-wits-pro-a20-dkt, this would require since
we have DM_SCSI enabled on the respective SoC.
Right now, ahci enabled in -u-boot.dtsi and will remove once same
supported by Linux.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for sun7i-a20-m5.dts, this would require since
we have DM_SCSI enabled on the respective SoC.
No need to send patch to Linux for this change, since this
dts is U-Boot specific.
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync sun7i-a20 dts(i) files from Linux 5.1-rc2
Linux commit details about the sun7i-a20* sync:
"ARM: dts: sun7i: bananapi: Add GPIO banks regulators"
(sha1: 09c6572290f018d73ec2e812e28bada34d41815f)
Here are U-Boot specific dts changes.
- s/uart0_pins_a/uart0_pb_pins for
sun7i-a20-ainol-aw1.dts
sun7i-a20-m5.dts
sun7i-a20-primo73.dts
sun7i-a20-yones-toptech-bd1078.dts
sunxi-itead-core-common.dtsi
- s/gmac_pins_mii_a/gmac_rgmii_pins for
sun7i-a20-m5.dts
- drop i2c0, i2c1 pins from
sunxi-itead-core-common.dtsi
- drop mmc0 pins from
sun7i-a20-primo73.dts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync sun8i-r40 dts(i) files from Linux 5.1-rc2
Linux commit details about the sun8i-r40* sync:
"ARM: dts: sun8i: r40: bananapi-m2-ultra: Add Bluetooth device node"
(sha1: 1e5f1db4ccd8348a21da55bff82f4263000879ef)
Linux commit details about the sun8i-v40* sync:
"ARM: dts: sunxi: Fix I2C bus warnings"
(sha1: 0729b4af5753b65aa031f58c435da53dbbf56d19)
Cc: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Define a label for flash node so that it can be
referenced easily as required.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
spi-flash compatible string is needed for reading tx and rx bus
widths, hence add this compatible string to flash node.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
add labels to rtc, pinctrl and watchdog node.
This makes it possible to reference the nodes
from board dts files.
Signed-off-by: Heiko Schocher <hs@denx.de>
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
-----BEGIN PGP SIGNATURE-----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=KLsH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imx
Move to DM
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
Usually the Linux dts changes were synced in specific tags in Allwinner,
to keep track for whats been synced so-far and plan for future syncs.
But this patch sync sun50i-h6* dts(i) files from Linux w/o any specific
tag since these dts(i) changes are required for new H6 boards support.
Linux commit details about the sun50i-h6* sync:
"arm64: dts: allwinner: h6: move MMC pinctrl to dtsi"
(sha1: 6ba2e45d57afdfd982d12f168edd6a79a65075d8)
Linux commit details about the sun8i-tcon-top.h sync:
"dt-bindings: display: sunxi-drm: Add TCON TOP description"
(sha1: 59a9c39544cd1e5952c2a33028d71aa8180648f8)
Part of the sync initiated by 'Clément Péron'.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Fix broken build:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix broken build:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Update device tree in preparation of further driver model migration:
Ethernet FEC, ESDHC aka MMC/SD card, I2C, NFC aka NAND flash controller,
USBH_PEN GPIO regulator.
Add iomux resp. pinctrl entries to be removed from proprietary platform
data: DSPI, ESDHC, FEC, I2C, NFC, UART, USBH_PEN GPIO.
Introduce a U-Boot specific device tree with some required
u-boot,dm-pre-reloc properties: soc, aips0, pinctrl_ddr and uart0 incl.
pinctrl.
While at it also update the MAINTAINERS file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
... as preparation for additional driver model coonversions.
We use CONFIG_OF_EMBED here to keep u-boot.imx as final binary name. So we
maintain compatibility with the original TBS u-boot and available HOWTOs
for u-boot updates.
Signed-off-by: Soeren Moch <smoch@web.de>
This commit brings a separate file in which the U-Boot specific
properties (like 'dm-pre-reloc') are provided.
Such approach allows easy sync with upstream Linux kernel in the
future.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit provides update and renames the bk4r1.dts to vf610-bk4r1.dts
file with more on SoC HW description.
The pcm052.dts has been renamed to vf610-pcm052.dts as well.
Moreover, a new vf610-pcm052.drsi file has been introduced
to reuse the common code between devices based on Phytec's
pcm052 modules.
Ported from Linux kernel - v4.20 (tag)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch allows moving vf610 based boards to a device tree and model.
Ported from Linux kernel - v4.20 (tag)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This patch provides definitions necessary for VF610 DDR pad configurations.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
-----BEGIN PGP SIGNATURE-----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=NrV8
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mips
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
- Misc dts files sync'ed with Linux version (Chris)
- Orion watchdog fix (Chris)
- kwbimage changed to also support Marvell bin_hdr binary (Chris)
- Add DM support to enable CONFIG_BLK for sata_mv (Stefan)
- Enable BLK on multiple platforms (Stefan)
- Misc minor fixes to AXP theadorable board (Stefan)
- Correct logic for DM_SCSI + unconverted drivers check (stefan)
- Misc changes to kirkwood to enable DM_USB here (Chris)
- Change ahci_mvebu to enable usage on A38x (Baruch)
- Update the kirkwood entry in git-mailrc (Baruch)
- Misc minor improvements (turris, documentation) (Baruch)
- Enhance sata_mv to support Kirkwood as well (Michael)
- Add wdt command (Michael)
- Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG
board support (Chris)
Adds alias to set the pincontrol seq id.
For STMFX gpio expander, force sequence number after
the last bank (GPIOZ) to avoid conflict between STM32MP and STMFX
gpio bank sequence number.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add adc related nodes. These nodes are used to detect the
current supplied by USB type-C power in port on DK1 and DK2
boards.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch synchronizes U-boot DT with kernel one
This is based on https://patchwork.kernel.org/cover/10797115/
This patch adds initial support of STM32MP157 discovery boards:
- Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1).
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
and 512MB of DDR3. Several connections are available on this boards:
4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ...
- Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2).
This board is a "super-set" of stm32mp157a-dk1. A display panel (otm8009a)
and Murata wifi/BT combo is added.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Updates the stm32mp157c devicetree to bind the U-Boot PSCI driver need for
power off command; TF-A for stm32mp15x supports PSCI 1.0.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Alignment with kernel driver name & binding
introduced by https://patchwork.kernel.org/cover/10761943/
to use the final marketing name = STPMIC1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Prepare file modification for kernel alignment and
rename driver to stpmic1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
As per recent TRM[1], PBIAS cell on dra7 devices supports
3.3v and not 3.0v as documented earlier.
Update PBIAS regulator max voltage and the voltage written
in the driver to reflect this.
[1] http://www.ti.com/lit/pdf/sprui30
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
With the memory mapping giving us some more avialable RAM, this
updates the da850-evm-u-boot.dtsi to include the serial port, SPI
and Flash nodes along with some dependent nodes in the SPL dtb.
This also removes the platform data initialization code for the
serial port and SPI Flash.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch adds dt node for DP83867 phy used on K2G ICE board and
also enable netcp device nodes for the board.
EVM hardware spec recommends to add 0.25 nsec delay in the tx
direction and 2.25 nsec delay in the rx direction for internal
delay in the clock path to be on the safer side.
The board straps RX_DV/RX_CTRL pin of on board DP83867 phy in mode
1. Unfortunately, the phy data manual disallows this. Add
ti,dp83867-rxctrl-strap-quirk in the phy node to allow software to
enable workaround suggested for this incorrect strap setting. This
ensures proper operation of this PHY.
The dts bindings are kept in sync with that from 4.14.y linux
kernel. This required the pinmux device related bindings to be
commented out to allow for compilation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch removes the unused phy-mode property from the phy dt node. On
K2G, currently link-interface determines if phy is used or not and is
already set to use rgmii. So this is not needed. Besides phy-mode should
be added to slave interface configuration of the cpsw driver, not in the
phy node.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is no reason not to use the Linux "jedec,spi-nor" binding in U-Boot
dts files. This compatible has been added in sf_probe, let use it.
This patch switches to jedec,spi-nor when spi-flash is used in the DTS
and DTSI files, and removed spi-flash when jedec,spi-nor is already
present.
The x86 dts are switched in a separate commit since it depends on a change
in fdtdec.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Evgeniy Paltsev <paltsev@synopsys.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Patrick Delaunay <Patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Sync armada-385-db-88f6820-amc.dts with Linux. Retain the
u-boot,dm-pre-reloc and nand differences.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board was added to u-boot first but the Linux maintainers requested
a more descriptive name. Rename the file to match the Linux usage and
update the board defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The DB-XC3-24G4XG is a switch development board from Marvell. It can
either use and external CPU card such as the db-88f6820-amc or the
internal CPU that is integrated into the switch.
Add support for running U-Boot on the internal CPU and enable the USB,
SPI and NAND peripherals. For now this needs the bin_hdr from the
Marvell U-Boot for this board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the hardware watchdog to guard against system lock ups when
running in the SPL or U-Boot. Stop the watchdog just before booting so
that the OS can re-enable it if needed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Bring in the Armada 370/XP dts/dtsi files from Linux. As U-Boot hasn't
got the new NAND driver the updating binding has not been included.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add DT node for MCU NAVSS its components to get DMA working on AM654
SoC.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Texas Instruments' System Control Interface (TI-SCI) Message Protocol
abstracts management of NAVSS resources, like PSI-L pairing and
unpairing, UDMAP tx/rx/flow configuration and Rings.
This patch adds support for requesting and configuring such resources
from TI-SCI firmware.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Import Linux 5.0 DT from 1c163f4c7b3f ("Linux 5.0") for the
meson-gxl-s805x-libretech-ac board and the corresponding changes
in meson-gxl.dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds *-u-boot.dtsi files for p200 and p201 boards
These are just copies of arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds the device trees for p200 and p201 boards.
Synced from kernel 5.0.0
Commit: a667cb7a94d4 ("Merge branch 'akpm' (patches from Andrew)")
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The E2 Alt board has two USB ports, add missing DT nodes to make the
USB available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen3 device trees with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen2 device trees with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip
AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage.
This patch adds support for this board including SPL support. Therefore
the AT91Boostrap is not needed on this platform any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This makes it possible to reference the watchdog DT node via "&watchdog"
from board dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Migrate the following options to CONFIG_DM:
CONFIG_DM_GPIO
CONFIG_DM_MMC
CONFIG_DM_ETH
CONFIG_DM_SERIAL
CONFIG_DM_USB
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
After the commit: "eth: dm: fec: Add gpio phy reset binding"
SHA1: efd0b79106
The FEC ETH driver switched to PHY GPIO reset performed with data defined
in DTS.
For the HSC|DDC boards the GPIO reset signal is active low and hence the
wrong DTS description must be changed (otherwise the reset for ETH is not
properly setup).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Activate I2C7 on Alt to allow access to the PMIC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
An ADATA 16GB Industrial MLC card has so much capacitance on the Vcc
pin that the usual toggling of regulator to power the card off and on
is insufficient. When the card is calibrated into UHS SDR104 mode, it
will remain in that mode across the power cycle and subsequent attempt
to communicate with the card will fail.
The test with this card is to insert it into an SDHI slot and perform
"mmc dev 0 ; mmc dev 0", where the second "mmc dev 0" will fail.
Fix this problem by increasing the off-on delay from 0 to 20 mS.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since commit 27cb7300ff ("Ensure device tree DTS is compiled"),
build succeeds irrespective of the correctness of Makefile.
In fact, you can compile any defconfig without adding any entry in
arch/*/dts/Makefile.
As a result, a lot of wrong code have been merged unnoticed.
I am going to revert that commit, and lots of hidden issues have
come to light:
[1] Typos
armada-3720-uDPU.dts, sun8i-a83t-tbs-a711.dts
use the extension ".dts" instead of ".dtb"
[2] DTB is associated to undefined CONFIG option
For example, mx6sllevk_defconfig defines CONFIG_MX6SLL, but
associates its device tree to CONFIG_MX6SL, which is undefined.
[3] Lots of entries are missing
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
[trini: add imx6ul pico dtbs]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Enable network interface on clearfog_gt_8k (Baruch)
- Fix dreamplug boot by adding an spi0 alias to the DT (Chris)
- Fix / enhance Marvell ddr3 setup / parameters (Chris)
- Change CONFIG_SYS_MALLOC_F_LEN to 0x2000 on db-88f6820-amc (Chris)
- Enable SPL_FLASH_BAR on db-88f6820-amc (Chris)
- Use correct pcie controller name in Armada-38x dts files (Chris)
- Disable d-cache on Kirkwood platforms as currently needed (Chris)
- Add a more descriptive comment to pci_mvebu.c (Stefan)
- Update Marvell maintainers entry (Stefan)
When armada-385.dtsi was sync'd from Linux the name of the node
describing the pcie controller was changed from pcie-controller to pcie.
Some of the boards that include armada-385.dtsi were missed in the
update retaining the old name. This updates the affected boards.
Reported-by: Влад Мао <vlaomao@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The conversion to DM_SPI managed to break accessing the environment on
dreamplug. This is because the environment code relies on being to able
to select the SPI device based on the sequence number. Add an alias so
that the spi0 bus gets sequence number 0.
Reported-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Stefan Roese <sr@denx.de>
Syscon register is required in dts to select correct
PHY interface.
Fix error below:
Net: Failed to get syscon: -2
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
spba-bus has a few nodes under it including the UART1 and
some ESPI buses. In order to use them in SPL, the
u-boot,dm-spl flag needs to be added to the spba-bus@2000000
container.
Signed-off-by: Adam Ford <aford173@gmail.com>
Import the device tree files from kernel 5.0-rc6 in preparation
for driver model conversion.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Just add spaces around '=' sign for clarity.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add startup time to LDO regulators of S2MPS11 PMIC on Odroid XU3/XU4/HC1
family of boards to be sure the voltage is proper before relying on the
regulator.
The datasheet for all the S2MPS1x family is inconsistent here and does
not specify unambiguously the value of ramp delay for LDO. It mentions
30 mV/us in one timing diagram but then omits it completely in LDO
regulator characteristics table (it is specified for bucks).
However the vendor kernels for Galaxy S5 and Odroid XU3 use values of 12
mV/us or 24 mV/us.
Without the ramp delay value the consumers do not wait for voltage
settle after changing it. Although the proper value of ramp delay for
LDOs is unknown, it seems safer to use at least some value from
reference kernel than to leave it unset.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The ADC block requires VDD supply to be on so provide one.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
v2019.01 commit cbff9f80ce ("ARM: dts: rmobile: Sync Gen3 DTs with
Linux 4.19.6") made the sdhi/usb nodes available in r8a77965.dtsi.
Hence, remove the SDHI/USB nodes from r8a77965-u-boot.dtsi. This is
equivalent to partially reverting below v2019.01 commits:
- f529bc551b ("ARM: dts: rmobile: Extract USB nodes on M3N")
- 830b94f768 ("ARM: dts: rmobile: Extract SDHI nodes on M3N")
Duplicating the nodes from <soc>.dtsi to <soc>-u-boot.dtsi is obviously:
- not needed if no U-boot-specific changes are needed in those nodes.
- potentially dangerous/error-prone, since the duplicated properties
override the properties originally defined in <soc>.dtsi. One
possible consequence is that <soc>.dtsi is getting an update from
Linux, while <soc>-u-boot.dtsi stays unchanged. In this situation,
the obsolete property values from <soc>-u-boot.dtsi will take
precedence masking some of the <soc>.dtsi updates, potentially
leading to all kind of obscure issues.
Below is the dtdiff of r8a77965-salvator-x-u-boot.dtb (the only "user"
of r8a77965-u-boot.dtsi) before and after the patch (slightly
reformatted to avoid 'git am/apply' issues and to reduce the width).
What below output means is there is already a mismatch in some of
SDHI/USB nodes between r8a77965.dtsi and r8a77965-u-boot.dtsi. Since no
U-Boot customization is needed in SDHI/USB DT nodes, get rid of them in
r8a77965-u-boot.dtsi.
$> dtdiff before-r8a77965-salvator-x-u-boot.dtb \
after-r8a77965-salvator-x-u-boot.dtb
--- /dev/fd/63 2019-03-09 12:57:40.877963983 +0100
+++ /dev/fd/62 2019-03-09 12:57:40.877963983 +0100
@@ -1471,7 +1471,7 @@
bus-width = <0x4>;
cd-gpios = <0x51 0xc 0x1>;
clocks = <0x6 0x1 0x13a>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
interrupts = <0x0 0xa5 0x4>;
max-frequency = <0xc65d400>;
pinctrl-0 = <0x4d>;
@@ -1492,7 +1492,7 @@
sd@ee120000 {
clocks = <0x6 0x1 0x139>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
interrupts = <0x0 0xa6 0x4>;
max-frequency = <0xbebc200>;
power-domains = <0x1 0x20>;
@@ -1504,7 +1504,7 @@
sd@ee140000 {
bus-width = <0x8>;
clocks = <0x6 0x1 0x138>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
fixed-emmc-driver-type = <0x1>;
interrupts = <0x0 0xa7 0x4>;
max-frequency = <0xbebc200>;
@@ -1526,7 +1526,7 @@
bus-width = <0x4>;
cd-gpios = <0x5a 0xf 0x1>;
clocks = <0x6 0x1 0x137>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
interrupts = <0x0 0xa8 0x4>;
max-frequency = <0xc65d400>;
pinctrl-0 = <0x56>;
@@ -1868,14 +1868,14 @@
usb-phy@ee0a0200 {
#phy-cells = <0x0>;
- clocks = <0x6 0x1 0x2be>;
+ clocks = <0x6 0x1 0x2bf>;
compatible = "renesas,usb2-phy-r8a77965", "renesas,rcar-gen3-usb2-phy";
phandle = <0x47>;
pinctrl-0 = <0x4c>;
pinctrl-names = "default";
power-domains = <0x1 0x20>;
reg = <0x0 0xee0a0200 0x0 0x700>;
- resets = <0x6 0x2be>;
+ resets = <0x6 0x2bf>;
status = "okay";
};
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
U-Boot currently uses Gen2 QSPI in 1-bit mode, enforce it until
we can do better using the new SPI NOR framework.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch enables UMS on the nyan devices like the nyan-big.
A patch like this has been sent in by Stephen Warren some time ago for
other tegra devices: commit e6607cffef.
But the nyan devices never received that functionality.
Signed-off-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Internal keyboard of nyan-big is only working when cold booting by pressing [reload/refresh]+[power] button.
With this patch keyboard is working by only pressing [power] button.
Signed-off-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Switch to using the omap3-u-boot.dtsi file for needed properties.
- Remove a few SPL features to free up more SRAM space.
- Switch CONFIG_SYS_TEXT_BASE to the normal default, we don't need to
worry about X-Loader at this point anymore.
- A few related updates to SPL options as part of switching to DM SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With the generic omap3-u-boot.dtsi file available, this patch
increased the memory of the various incarnations of the omap3_logic
board, and points their respective u-boot.dtsi files to the newly
created generic one, and removes the PLATDATA from the board file.
These are all done at once because the're all utilizing the same
omap3logic.c board file.
Signed-off-by: Adam Ford <aford173@gmail.com>
Create generic omap3-u-boot.dtsi file that omap3 based boards
can include to generate device tree in SPL for booting MLO.
Credit should go to Tom Rini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
This commit converts the brxre1 board to DM,
for this we have todo following things:
- add a devicetree-file for this board
- drop all obsolete settings from board header-file
- use dm_i2c_xxx calls for read/write to the resetcontroller
- request gpios before operate them
Serues-cc: trini@konsulko.com
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As the H5 is pin compatible with the H3, vendors tend to upgrade their
existing H3 products with an H5 SoC swap. This is the case with the
Bananapi M2+ H5.
Add the following to support it:
- device tree file: synced from Linux v5.0-rc1,
- defconfig: copy of bananapi_m2_plus_h3_defconfig with only SoC
family and default device tree file name changed
- MAINTAINERS entry
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
As of commit aa8fee415f46 ("ARM: dts: sun8i: h3: Split out
non-SoC-specific parts of Bananapi M2 Plus") in the Linux kernel, the
device tree for the Bananapi M2+ has been split into a common dtsi file,
and an SoC-specific board device tree file that includes both the shared
dtsi file and the soc dtsi file. This was done to support both the H3
and H5 variants of the same board. This is similar to what was done for
the Libre Computer ALL-H3-CC in U-boot commit d7b17f1c24 ("sunxi: Split
out common board design for ALL-H3-CC device tree").
The newly split files are directly synced from Linux tag v5.0-rc1.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd] to the ones
from kernel v4.20 (commit 8fe28cb58bcb2).
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This allows us to keep the basic dts[i] files up-to-date with
the ones in kernel, but at the same time allowing the u-boot
to add its own properties to the existing nodes.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
As per the zc1275 design x1 mode is enabled so changing the
spi-rx-bus-width property to x1.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
Linux commit a13f18f59d26 ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Linux docs:
Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds reset-on-timeout to FPD WDT which will trigger an
interrupt to PMU when watchdog expiry happens and PMU takes the
necessary action. If this property is not enabled, reason will not be
known when watchdog expiry happens.
This patch also modifies the default timeout to 60 seconds. Reason is
that if u-boot enables WDT, it will set the timeout to 10 seconds and
this is not enough to boot till Linux and start the WDT application in
Linux. 60 seconds is the maximum safest value to boot till Linux and
start the WDT application.
Users need to change this timeout value to fit their needs.
Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Both boards are made by Avnet, Inc. So add an additional
value to the compatible property
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Import liteSOM and liteboard dts files from Linux v4.20. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.
zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.
DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Boards have only one controller enabled that's why move to DM_I2C is
easy.
Add also i2c alias for not to be shown as i2c bus -1 because alias
doesn't exist.
Config file points to MAC stored in eeprom but it is not listed that's
why I have added 24c08 part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds new mini target for versal.
This configuration is very minimal in size which runs
from OCM. It contains support for mtest which can be
used for running DDR memory tests.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds mini eMMC configuration which has only
emmc0 and emmc1 functionalities and can run from small
amount of memory. This is required for memory constraint
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The PCIe slot PERST signal is active low. Fix the gpio signal
description in the dts.
This happened to work because the pcie_dw_mvebu driver sets the reset
gpio level to 1 (high) to release the reset. The following commit will
fix that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
Update the flashmap so that this board can be started over USB A-A. It
is slightly different from snow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Update the spring settings to use this codec, which is what it actually
shipped with.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm63158 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
- Add st,digbypass on clk_hse node (needed for board rev.C)
- MLAHB/AHB max frequency increased from 200 to 209MHz, with:
- PLL3P set to 208.8MHz for MCU sub-system
- PLL3Q set to 24.57MHz for 48kHz SAI/SPI2S
- PLL3R set to 11.29MHz for 44.1kHz SAI/SPI2S
- PLL4P set to 99MHz for SDMMC and SPDIFRX
- PLL4Q set to 74.25MHz for EVAL board
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
commit fdce9d35dc ("arm: dts: am33xx: Sync dts with Linux 4.20.0")
did remove the "u-boot,dm-spl" flag from the 'ocp' bus which was
introduced with
commit 19aa4ac09d ("dts: am33xx: add u-boot, dm-spl to ocp bus")
Due to this all boards having CONFIG_SPL_OF_CONTROL enabled are broken
because they cannot bind/probe the boot-media interface during SPL
stage.
This commit introduces the 'am33xx-u-boot.dtsi' which is included with
the auto include mechanism. The am33xx-u-boot-dtsi adds the important
"u-boot,dm-pre-reloc" to the 'ocp bus' (the root bus of almost all
peripherals, at least the bootable ones).
The peripherials (mmc, spi, ...) needed during SPL stage need to be
equipped with the 'u-boot,dm-pre-reloc' in their responsible dts file.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
With the new DM_VIDEO support in the Armada XP LCD driver, this patch
adds the needed DT node for the LCD controller to the theadorable dts
file. This DT property is not added to the Armada XP dtsi files, as this
LCD feature is pretty unusual for this SoC and I personally know of no
other board that uses this controller.
This patch also enables CONFIG_BMP_16BPP/24BPP/32BPP, as the "old" bmp
command supported these BMP files.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This adds initial support for micro-DPU (uDPU) board which is based on Armada-3720 SoC.
micro-DPU is the single-port FTTdp "distribution point unit" made by Methode Electronics
which offers complete modularity with replaceable SFP modules both for uplink and downlink
(G.hn over twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Luis Torres <luis.torres@methode.com>
Cc: Scott Roberts <scott.roberts@telus.com>
Cc: Paul Arola <paul.arola@telus.com>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that the PCIe driver supports DM and DT parsing, enable the PCIe DT
nodes that are used by this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
This patch sync's the PCIe DT nodes with the recent Linux v4.20 version.
This change makes it easier to reference specific PCIe nodes in the
board dts files to e.g. enable a PCIe port as this is now necessary with
the new DM PCI driver for these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcVG0IAAoJECaAFcEOcohNKVAIAJd3DN/qudcVQdkuvAGK6WIk
Umxkm6rxHwur7oU+wxvK1p1l/0YTFBeCfo15quH1DkSc/WIUnmBlLmDvqpGVmPmh
ydZNE9ZChn0OKRIaM6pKJr+3p155cQDe6Mgg2j/5CnNx28KxT+vu7EqZbZvbQPag
wcZEK6Z6E5jMVHVn2lbLgmsBPmY7ksX168IqpvzTxIj0a4J3n0DcJUnO4RBBS0Q2
PGEvFhTvigVWs6r6GL0gLn3VwnQX30xQlIuKKORPcdhjk97cJcS4+bRxdTENTKD9
j3+pgyl1n04O8sPONZS7pH3fvJwtC6SwnoxTYxGrvjedw1LxbyHG3cqcGDg/TJ8=
=ik3X
-----END PGP SIGNATURE-----
Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchip
u-boot-rockchip changes for 2019.04-rc1:
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
Add some U-Boot-specific settings. These should really go in the
*u-boot.dtsi file, but it seems that rk3399 does not use that yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This memory is used on Bob. Add settings for this, taken from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This file has changed upstream, with some additions and changes. Move the
U-Boot version towards this.
Some USB changes seem to be incompatible with how the bindings work on
rockchip in U-Boot. Testing is needed to make sure that USB still works
correct, and adjust the code (not device tree) if not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Bring in these files from Linux v4.20.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To match the iomux setting of uart2 at SPL, correct the uart2
default pin configuration, if not changed, the evb-rk3229 can't
output the log message.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds support for the ASUS C201, a RK3288-based clamshell
device. The device tree comes from linus's linux tree at
3f16503b7d2274ac8cbab11163047ac0b4c66cfe. The SDRAM parameters
are for 4GB Samsung LPDDR3, decoded from coreboot's
src/mainboard/google/veyron/sdram_inf/sdram-lpddr3-samsung-4GB.inc
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Like on rk3399-puma we want to continue booting the fill U-Boot from
the same device as the SPL stage.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Jerry uses a max98090 audio codec and the internal SoC I2S peripheral.
Enable sound support and add the required device-tree pieces.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Although not required, it doesn't hurt to explicitly map the USB ports to
a USB controller. Without this, the port number will be derived from the
binding order of the peripheral devices.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This USB port is mainly used for RNDIS and DFU. To be able to use it with
DM_USB and DM_USB_GADGET, we need to provide a dr_mode value in the DTS.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
add u-boot specific am335x-shc-u-boot.dtsi file,
in which we add u-boot specific adaptions.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
add DTS from linux tree commit
"47bfa6d9dc8c060bf56554a465c9031e286d2f80"
change for U-Boot:
switch to SPDX-license identifier.
Signed-off-by: Heiko Schocher <hs@denx.de>
There's no reliable way to reuse the hhi entry from the vpu as is done
in the linux kernel, so we duplicate it here.
We will be able to sync against kernel DTS in the future when the VPU
gets based on the clock framework rather than the HHI reg.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The hdmi_5v regulator must be enabled to provide power to the physical HDMI
PHY and enables the HDMI 5V presence loopback for the monitor.
Fixes: b409f625a6d5 ("ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
[backport of linux commit e1f2163deac059ad39f07aba9e314ebe605d5a7a]
Flag the appropriate nodes with u-boot,dm-pre-reloc
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Like other Allwinner A64 boards, pinebook also need altering
auto-numbering of mmc2 to mmc1 which is available in common
sunxi dsti file, sunxi-u-boot.dtsi
Pinebook has a separate sun50i-a64-pinebook-u-boot.dtsi which
takes more precedence for u-boot.dtsi inclusion and it eventually
failed to include the sunxi-u-boot.dtsi.
So, this patch add support to include the sunxi-u-boot.dtsi in the
sun50i-a64-pinebook-u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> # Pinebook
Environment and fastboot mmc devices are configured based on the number
of mmc slots defined on particular board configs, MMC_SUNXI_SLOT_EXTRA.
If MMC_SUNXI_SLOT_EXTRA is more than 1, the default env and fastboot
mmc devices is mmc1 by assuming mmc0 is SD and mmc1 is emmc device.
But with DM_MMC the mmc devices are numbered as per the dts node
enablement. If there is a chance of having enabling all mmc nodes
in dts say mmc0, mmc1, mmc2 then the default env and fastboot devices
will failed to assign proper emmc device since mmc2 is emmc in most
of the Allwinner platforms.
So, we need to alter the auto-numbering by aliasing mmc2 to mmc1 since
aliases take precedence over auto-numbering.
If the dts enables mmc0, mmc1, mmc2, then all the nodes will probe
sequentially and auto-numbered as it is. but when aliases mmc1 with mmc2
the resulting number should be that mmc0 is till mmc0, mmc2 become mmc1
and mmc2 become mmc1
Without aliases of mmc1 = &mmc2;
-------------------------------
MMC: mmc@1c0f000: 0, mmc@1c10000: 1, mmc@1c11000: 2
With aliases of mmc1 = &mmc2;
----------------------------
MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... OK
Some platforms like A20 has mmc0...mmc3, but there is no usecases now
for enabling all mmc controllers in any of A20 board dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The i.MX6 SOM and development kits have undergone significant
updates and changes over the past few months. This re-sync's
the U-Boot with Logic PD's BSP.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch sets up an alias for mmc0 to usdhc3.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing warp7 bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing warp7 boot code will
work unmodified.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch imports the Linux kernel warp7 dts as at upstream kernel commit
cf76c364a1e1.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
As pointed out by Lucas WDOD1_WDOG_ANY should be WDOG1_WDOG_ANY. Once
corrected we can import the latest kernel DTS unmodified.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reported-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
These nodes are required by CX9020 when build with CONFIG_DM_MMC=y
They are copied from Linux 4.20
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Introduce u-boot dtsi for i.MX8QXP MEK board.
we do not introduce a common dtsi for SoC, because different board
has different requirement on which needs to be enabled in SPL DM.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In preparation of adding CONFIG_DM_MMC support use separate device
trees for raw NAND and eMMC devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
As Poplar supports running TF-A with OP-TEE as BL32
payload, add op-tee node in DT, which enables usage of
OP-TEE driver (which provides an interface for requesting services
from OP-TEE).
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
It adds missing pinctrl headers, updates clock header and sync up Poplar
device tree with kernel 4.20 release.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* Add pinctrl node for TLMM and add mux request for uart node.
* Rename uart to the actual board uart port.
* Fix indentendation of sdhc2 node.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The miamiplus contains a speedgrade-2 device, which may run the CPU at 800MHz.
Change the PLL setting to 800MHz, and adapt the setpoints in the devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patches renames sd nodes in dts to be in line with
kernel. This patch also modifies the references for the same
in code.
It checks mmc first to have no time penalty for new DT node names based
on left-to-right expression evaluation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The memory area [0x4000000-0x4200000[ is occupied by the PSCI firmware. Any
attempt to access it from U-Boot leads to an immediate crash.
So let's make the same memory reservation as the vendor device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
DTC issues a warning because #address-cells and #size-cells properties
are not set in the mdio node.
Also add ethernet1 alias.
Also add RTC node.
Also fix USB3 regulator startup delay time.
Also fix PCI Express SERDES speed to 5 GHz (this is only cosmetic, the
speed value is not used byt the comphy driver for PCI Express, but
should be 5 GHz nonetheless).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Check if Mox modules are connected in supported mode, then configure
the MDIO addresses of switch modules.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Sync the Armada-38x device tree files with Linux 4.20-rc5. The changes
not taken are new compatible strings for the uart and nand flash
controller. The nand binding is best updated if/when the mtd/nand
infrastructure is updated.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Update all A80 devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commits.
arch/arm/boot/dts/sun9i-a80*:
commit 190e3138f9577885691540dca59c2f07540bde04
Merge: cafc87023b0d a7affb13b271
Author: Arnd Bergmann <arnd@arndb.de>
Date: Tue Mar 27 14:58:00 2018 +0200
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
include/dt-bindings/*/sun9i-a80-*:
commit 783ab76ae553abc23f80ef7511052d055697531b
Author: Chen-Yu Tsai <wens@csie.org>
Date: Sat Jan 28 20:22:36 2017 +0800
clk: sunxi-ng: Add A80 Display Engine CCU
Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same
dts is not available in Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis-devboard target to dtb makefile
- add dtsi file for Neutis N5 needs
- add config file for Neutis N5 Dev board
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: update proper commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Remove aliases property name warning while compilation:
Warning (alias_paths): /aliases: aliases property name must
include only lowercase and '-'
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This adds device tree for OMAP3 IGEP based boards and the DM_MMC driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add MMC nodes for HiKey board based on HI6220 SoC. There are three MMC
controllers in this SoC, first one used for eMMC, second one used
for SD card and third one is not used by u-boot.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SDMMC reset is missing from DT, so the reset manager cannot unreset
the SDMMC. Add the missing DT reset entry.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
This patch sets VDD_LOG to 950 mV on RK3399-Q7.
This is required to address stability issues on Puma
in heavy-load use-cases.
Reported-by: Assaf Agmon <assaf@r-go.io>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch eliminates the non-standard entries "rockchip,pwm_id"
and "rockchip,pwm_voltage". They are neither documented nor
read out by any driver.
Additionally it introduces the entry regulator-init-microvolt
and sets it to 900 mV, which is the default target value
for VDD_LOG.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This file is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This node is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Currently, the DWC3 USB node is out of sync because the bindings
for the UniPhier DWC3 PHY diverged between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Under U-boot, the WiFi SDIO Module should be disabled and the
eMMC modules should be enabled, so this patch adds an s400-u-boot.dtsi
include file specific for U-Boot that will be included by the build system.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
