Back in fc46bae a "clean up" was introduced that intended to reconcile
some of the AM335x codepaths based on how AM43xx operates.
Unfortunately this introduced a regression on the DDR2 platforms. This
was un-noticed on DDR3 (everything except for Beaglebone White) as we
had already populated sdram_config correctly in sequence. This change
brings us back to the older behavior and is fine on all platforms.
Tested on Beaglebone White, Beaglebone Black and AM335x GP EVM
Reported-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add backlight enable GPIO, and delay needed for panel powerup
via FIMD DT node.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now that parade driver supports reading SLP and RST GPIO
from DT, specify the same in parade DT node.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now that the exynos_fb driver supports handling backlight GPIO
via DT, specify pwm output property via FIMD DT node.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The existing setting for rpll_sdiv generates 70.5Mhz RPLL
video clock to drive 1366x768 panel on peach_pit.
This clock rate is not sufficient to drive 1920x1080 panel on peach-pi.
So, we adjust rpll_sdiv to 3 so that it generates 141Mhz pixel clock
which can drive peach-pi LCD.
This change doesn't break peach-pit LCD since 141/2=70.5Mhz, i.e FIMD
divider at IP level will get set to 1(the required divider setting
will be calculated and set by exynos_fimd_set_clock()) and hence
peach-pit LCD still works fine.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add get_lcd_clk and set_lcd_clk callbacks for Exynos5800 needed by
exynos video driver.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Commit 2e82e92526 'Exynos: Clock: Cleanup
soc_get_periph_rate' introduced a bug in I2C config. This patch makes cros_ec
keyboard working again on Samsung Chromebook (snow).
Changes in V2: reorder lines as requested by Joonyoung Shim.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Simon Glass <sjg@chroimum.org>
Tested-by: Simon Glass <sjg@chroimum.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
ARCv2 cores may have built-in SLC (System Level Cache, AKA L2-cache).
This change adds functions required for controlling SLC:
* slc_enable/disable
* slc_flush/invalidate
For now we just disable SLC to escape DMA coherency issues until either:
* SLC flush/invalidate is supported in DMA APIin U-Boot
* hardware DMA coherency is implemented (that might be board specific
so probably we'll need to have a separate Kconfig option for
controlling SLC explicitly)
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Now when all infrastructure in ARC is ready for it let's switch ARC UART
to driver model.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
[1] Fix misspeling in ARC_CACHE_LINE_SHIFT dependency, now cache-line
lenth selection is correctly enabled if either I$ or D$ are enabled.
[2] Add dummy entry to target list to make sure target type is always
mentioned in defconfig. Otherwise defconfig for the first target in the
list will not have target name and later on with addition of the new
target on top of the list in Kconfig will lead to corrupted
configuration expanded from defconfig.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As discussed on mailing list we're drifting away from
CONFIG_SYS_GENERIC_GLOBAL_DATA in favour to use of board_init_f_mem()
for global data.
So do this for ARC architecture.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Intention behind this work was elimination of as much assembly-written
code as it is possible.
In case of ARC we already have relocation fix-up implemented in C so why
don't we use C for U-Boot copying, .bss zeroing etc.
It turned out x86 uses pretty similar approach so we re-used parts of
code in "board_f.c" initially implemented for x86.
Now assembly usage during init is limited to stack- and frame-pointer
setup before and after relocation.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
This separation makes maintenance of code easier because those low-level
interrupt- or exception handling routines are pretty static and usually
require not much care while start-up code is a subject of modifications
and enhancements.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Even though ARCompact and ARCv2 are not binary compatible most of
assembly instructions are used in both. With this change we'll get rid
of duplicate code.
Still IVTs are implemented differently so we're keeping them in separate
files.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
always
Make both invalidate_icache_all() and invalidate_dcache_all() available
even if U-Boot is configured with CONFIG_SYS_DCACHE_OFF and/or
CONFIG_SYS_ICACHE_OFF.
This is useful because configuration of U-Boot may not match actual
hardware features. Real board may have cache(s) but for some reason we
may want to run U-Boot with cache(s) disabled (for example if some
peripherals work improperly with existing drivers if data cache is
enabled). So board may start with cache(s) enabled (that's the case for
ARC cores with built-in caches) but early in U-Boot we disable cache(s)
and make sure all contents of data cache gets flushed in RAM.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.
As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Config MCKR according to the datasheet sequence, or else it
will cause the MCKR configuration failed.
Remove timeout checking for clock configuration, if configure
the clock failed, let the system hang while not run in wrong
clock configuration.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
To facilitate changing lowlevel_init to become s_init, move the current
contents of s_init into board_init_f and add the rest of what
board_init_f does here.
In order to compile clean without CONFIG_SKIP_LOWLEVEL_INIT set, leave an
empty stub of s_init(). It can be removed when lowlevel_init becomes s_init.
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Matt Porter <mporter@konsulko.com> on sama5d3_xplained
Signed-off-by: Tom Rini <trini@ti.com>
[rebased on current master, leave s_init() as empty stub]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The commit 8dfafdd (Introduce common timer functions), add common
timer functions, we can use them directly.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[rebase on current master]
Sigend-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Even the 8-bit case needs KBCB configured, as pin D7 is located in this
pingroup.
Please note that pingroup ATC seems to come out of reset with its
config set to NAND so one needs to explicitly configure some other
function to this group in order to avoid clashing settings which is
outside the scope of this patch.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A while ago I got Russell to change the machine type of our Colibri T20
from COLIBRI_TEGRA2 to COLIBRI_T20 which at least in parts is also
reflected in his machine registry:
http://www.arm.linux.org.uk/developer/machines/list.php?id=3323
For us it is really very beneficial to actually still be able to boot
downstream L4T kernel with its working hardware accelerated
graphics/multimedia stack albeit it being proprietary/closed-source.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In accordance with our other modules supported by U-Boot and as agreed
upon for Apalis/Colibri T30 get rid of the carrier board in the board/
configuration/device-tree naming.
While at it also bring the prompt more in line with our other products.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This allows selection between CSI and DSI_B on the MIPI pads.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some pinmux controls are in a different register set. Add support for
manipulating those in a similar way to existing pins/groups.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move struct pmux_pingrp_desc type and tegra_soc_pingroups variable
declaration together with other pin/mux level definitions. Now the whole
file is grouped/ordered pin/mux-related then drvgrp-related definitions.
Fix typo in ifdef comment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Patches that added the Tegra210 pinctrl driver and renamed directories
arch/arm/cpu/tegra{$soc}-common -> arch/arm/mach-tegra/tegra-${soc}
crossed. Move the Tegra210 pinctrl driver to the correct location. This
wasn't detected since Tegra210 support is in the process of being added,
and isn't buildable yet.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
make the CPU clock selectable via Kconfig
this removes the sunxi specific CONFIG_CLK_FULL_SPEED defined in each
soc header and replaces it's use in board/sunxi/board.c with
CONFIG_SYS_CLK_FREQ from Kconfig which allows us to configure board
specific frequency on boot
Signed-off-by: Iain Paton <ipaton0@gmail.com>
[hdegoede@redhat.com s/CONFIG_SYS_CLK_FREQ/CONFIG_TIMER_CLK_FREQ/ for the
arch-timer clk speed on sun7i to fix mis-compile on sun7i]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
clock_set_pll1 would pick the next highest available cpu clock speed if
a value not in the pre defined table was selected. this potentially
results in overclocking the soc.
reverse the selection method so that we select the next lowest speed
and add the missing 912Mhz setting that's requested by sun7i which also
uses the sun4i clock code.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The usb0 / otg phy on sunxi boards has a bug where it wrongly detects a
high speed squelch on usb reset deassert when a lo speed device is plugged in.
The android kernel has a work around for this in the form of temporary
disabling the phy's squelch detection on reset deassert, this commit adds
the same workaround to the u-boot sunxi musb code, thereby fixing various usb
lo speed devices not working.
Tested with a (before non working) usb keyboard and a usb 2.4 GHz wireless
keyboard/mouse combo receiver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that loading files using semihosting can be done using
a command in standard scripts, and we have rewritten the boardfile
and added it to the Vexpress64, let's delete the external
interface to the semihosting file retrieveal and rely solely
on these commands, and staticize them inside that file so the
whole business is self-contained.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of sprinkling custom code and calls over the Vexpress64
boardfile, create a command that loads images using semihosting
just like we would load from flash memory of over the network,
using a special command:
smhload <image> <address>
This will make it possible to remove some custom calls and
code and make the boot easier.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The semihosting trap call does not like being inlined, probably
because that will mean register reordering screwing up the return
value in r0, so tag this function "noinline".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Collect CPU specific flags into the single place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Move the CPU type config options from include/configs/*.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf547x_8x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Move the CPU type config options from include/configs/M5235EVB.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf523x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Move the CPU type config options from include/configs/M52277EVB.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf5227x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
This commit intends to stop grepping CPU type in
arch/m68k/cpu/mcf5445x/config.mk.
Move the CPU type config options from include/configs/*.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf5445x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
This commit intends to stop grepping CPU type in
arch/m68k/cpu/mcf532x/config.mk.
Move the CPU type config options from include/configs/*.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf532x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
This commit intends to stop grepping CPU type in
arch/m68k/cpu/mcf530x/config.mk.
Move the CPU type config options from include/configs/amcore.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf530x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
This commit intends to stop grepping CPU type in
arch/m68k/cpu/mcf52x2/config.mk.
Move the CPU type config options from include/configs/*.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf52x2/config.mk.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
BCM2835 (used on Raspberry Pi) and BCM2836 (used on Raspberry Pi 2)
are similar enough. One of the biggest differences is the ARM
processor. It is reasonable to collect the source files into a
single place, arch/arm/mach-bcm283x/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory. Devices are scanned twice, before/after
relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation. As it is board-independent, handle it
globally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
The default value of CONFIG_SYS_MALLOC_F_LEN is defined by ./Kconfig
as 0x400. Each defconfig or Kconfig need not repeat the same value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
All the M68000 boards have switched to Generic Board.
This file is no longer necessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Huan Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have done with the generic board conversion for all the boards
of ARC, Blackfin, M68000, MicroBlaze, MIPS, NIOS2, Sandbox, X86.
Let's select SYS_GENERIC_BOARD for those architectures, so we can
tell which architecture has finished the conversion at a glance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
Move the option to Kconfig renaming it to CONFIG_HAVE_GENERIC_BOARD.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
My main motivations for this commit are:
[1] Follow the arch/arm/Makefile style of Linux Kernel
[2] Maintain compiler options systematically
Currently, we give -march=* and -mtune=* options inconsistently:
Only some of the CPUs pass -march=* and -mtune=* options.
By collecting such options into the single place arch/arm/Makefile
we can tell which options are missing at a glance.
[3] Prepare for deprecating arch/*/cpu/*/config.mk
Note:
This commit just moves the compiler options so as not to change
the behavior at all. It does not care about the correctness of
the given options. Fox example, "-march=armv5te" might be better
than "-march=armv4" for ARM946EJS, but it is beyond the scope this
commit. Also, filling the missing -march=* and -tune=* is left
to follow-up patches.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Allocate memory space for pre-allocation malloc and zero global data.
This code is partly from crt0.S.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
Intel Quark SoC integrates two 10/100 ethernet controllers which can
be connected to an external RMII PHY. The MAC IP is from Designware.
Enable this support with the existing U-Boot Designware MAC driver
so that the ethernet port on Intel Galileo board can be used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Using __DATE__ and __TIME__ results in an error due to -Werror=date-time
with gcc-4.9 (__DATE__ / __TIME__ might prevent reproducible builds) so
switch these over to U_BOOT_DATE / U_BOOT_TIME
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch cleans up the quark MRC codes coding style by:
- Remove BIT0/1../31 defines from mrc_util.h
- Create names for the documented BITs and use them
- For undocumented single BITs, use (1 << n) directly
- For undocumented ORed BITs, use the hex number directly
- Remove redundancy parenthesis all over the codes
- Replace to use lower case hex numbers
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
The callee (arch/arm/lib/cache-cp15.c) has a #ifdef
CONFIG_SYS_DCACHE_OFF conditional. The same conditional in the
caller (arch/arm/mach-uniphier/cache_uniphier.c) is redundant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The L2 cache is used as a temporary SRAM on SPL.
Now the secondary CPUs store the necessary code for jumping to
Linux on their L1 I-caches. So, the L2 cache can be disabled
much earlier, at the very entry of U-Boot proper (lowlevel_init).
This makes the boot sequence clearer.
Also, as the L1 cache has been disabled by the start.S,
enable_caches() does not need to do it again.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, the secondary CPU(s) are kicked three times:
Boot ROM ---(kick)--> SPL ---(kick)--> U-boot ---(kick)--> Linux.
It makes the boot sequence very complicated.
This commit merges the first and the second kicks, so the secondary
CPU(s) can directly jump from SPL to Linux.
arch/arm/mach-uniphier/smp.S is no longer necessary.
Linux boot test passed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
To remove the ifdef conditional of CONFIG_SKIP_LOWLEVEL_INIT,
add late_lowlevel_init.S to U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Ifdef conditionals for CONFIG options are not Kconfig-friendly.
Instead, define CONFIG_SPL_STACK to prepare for Kconfig moves.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable CONFIG_SPL_DM and CONFIG_SPL_SERIAL_SUPPORT, which provide
Driver Model UART support on SPL.
CONFIG_SYS_SPL_MALLOC_{START,SIZE} should be dropped because simple
malloc is preferred on SPL. Dlmalloc requires some static variables
on .data section that is not available yet for NOR boot mode etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The UniPhier platform is going to enable Driver Model and UART
support on SPL. Move UART pin settings to early_pin_init(),
which is called from SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since we do not have OF_CONTROL support for SPL, platform devices
are necessary to enable Driver Model on SPL.
To prepare for that, move platdevice.o to SPL and enable it by
CONFIG_SPL_DM.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The two Makefiles arch/arm/mach-uniphier/{ph1-ld4,ph1-sld8}/Makefile
are completely the same. We can improve the maintainability by
having one to include the other.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit a86ac9540e (ARM: UniPhier: include <mach/*.h> instead
of <asm/arch/*.h>), UniPhier platform does not need the symbolic
link arch/arm/include/asm. This option is not necessary either.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add basic SECO MX6Q/uQ7 board support (Ethernet, UART, SD are supported).
It also adds a Kconfig skeleton to later add more SECO board (supporting
SoC and board variants).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
IMX_CONFIG is currently passed via the SYS_EXTRA_OPTIONS which is marked
as deprecated.
Add a new Kconfig file under arch/arm/imx-common and define the
IMX_CONFIG Kconfig in there.
Each board is supposed to provide a default value pointing to the
appropriate imximage.cfg file.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Freescale boards are currently all defined in arch/arm/Kconfig, which
makes them hard to detect.
Moreover the MX6 SoC variant (Q, D, DL, S, SL) selection is currently
done via the SYS_EXTRA_OPTIONS option which marked as deprecated.
Move to a more standard way to select sub-architecture and board by
creating a Kconfig under arch/arm/cpu/armv7/mx6 and a new ARCH_MX6
option.
Existing MX6 board definitions should be moved in this new Kconfig in
choice menu, and new boards should be directly declared in this menu.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
As the u-boot-spl.lds is used only for armv7 SoCs (includes
sama5d3 and sama5d4), so move it to armv7 directory.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
This patch enable the MCI support for at91sam9rlek board.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase on ToT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Larry Johnson <lrj@acm.org>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Eric Millbrandt <emillbrandt@dekaresearch.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Erik Theisen <etheisen@mindspring.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stephen Williams <steve@icarus.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Panasonic's System LSI products, UniPhier SoC family, have been
transferred to Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
RX51 has a secure logic which uses different parameters compared to
traditional implementation. So, make the generic secure acr write
over-ride-able by board file and refactor rx51 code to use this.
While at it, enable the OMAP3 specific errata code for 454179, 430973,
621766.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the OMAP3 specific errata code for 454179, 430973, 621766
and while at it, remove legacy non-revision checked errata logic.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update to existing recommendation for L2ACTLR configuration to prevent
system instability and optimize performance.
These apply to both OMAP5 and DRA7.
Reported-by: Vivek Chengalvala <vchengalvala@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch enables the workaround for ARM errata 798870 for OMAP5 /
DRA7 which says "If back-to-back speculative cache line fills (fill
A and fill B) are issued from the L1 data cache of a CPU to the
L2 cache, the second request (fill B) is then cancelled, and the
second request would have detected a hazard against a recent write or
eviction (write B) to the same cache line as fill B then the L2 logic
might deadlock."
An l2auxctlr accessor implementation for OMAP5 and DRA7 is introduced
here as well.
Signed-off-by: Praveen Rao <prao@ti.com>
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
omap_smc1 is now generic enough to remove duplicate
omap3_gp_romcode_call logic that omap3 introduced.
As part of this change, move to using the generic lowlevel_init.S for
omap3 as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is in preperation of using generic cross OMAP code.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
set_pl310_ctrl_reg does use the Secure Monitor Call (SMC) to setup
PL310 control register, however, that is something that is generic
enough to be used for OMAP5 generation of processors as well. The only
difference being the service being invoked for the function.
So, convert the service to a macro and use a generic name (same as
that used in Linux for some consistency). While at that, also add a
data barrier which is necessary as per recommendation.
While at this, smc #0 is maintained as handcoded assembly thanks to
various gcc version eccentricities, discussion thread:
http://marc.info/?t=142542166800001&r=1&w=2
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
621766: Under a specific set of conditions, executing a sequence of
NEON or vfp load instructions can cause processor deadlock
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set L1NEON to 1
Based on ARM errata Document revision 20.0 (13 Nov 2010)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
430973: Stale prediction on replaced inter working branch causes
Cortex-A8 to execute in the wrong ARM/Thumb state
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set IBE to 1
Based on ARM errata Document revision 20.0 (13 Nov 2010)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
454179: Stale prediction may inhibit target address misprediction on
next predicted taken branch
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set IBE and disable branch size mispredict to 1
Also provide a hook for SoC specific handling to take place if needed.
Based on ARM errata Document revision 20.0 (13 Nov 2010)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add workaround for Cortex-A15 ARM erratum 798870 which says
"If back-to-back speculative cache line fills (fill A and fill B) are
issued from the L1 data cache of a CPU to the L2 cache, the second
request (fill B) is then cancelled, and the second request would have
detected a hazard against a recent write or eviction (write B) to the
same cache line as fill B then the L2 logic might deadlock."
Implementations for SoC families such as Exynos, OMAP5/DRA7 etc
will be widely different.
Every SoC has slightly different manner of setting up access to L2ACLR
and similar registers since the Secure Monitor handling of Secure
Monitor Call(smc) is diverse. Hence an weak function is introduced
which may be overriden to implement SoC specific accessor implementation.
Based on ARM errata Document revision 18.0 (22 Nov 2013)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Disable the warm reset and enable the cold reset for a more reliable
restart ('reset'). This is taken from the Linux kernel, see imx_src_init()
in arch/arm/mach-imx/src.c.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
While the Freescale ARMv8 board LS2085A will enter U-Boot both
on a master and a secondary (slave) CPU, this is not the common
behaviour on ARMv8 platforms. The norm is that U-Boot is entered
from the master CPU only, while the other CPUs are kept in
WFI (wait for interrupt) state.
The code determining which CPU we are running on is using the
MPIDR register, but the definition of that register varies with
platform to some extent, and handling multi-cluster platforms
(such as the Juno) will become cumbersome. It is better to only
enable the multiple entry code on machines that actually need
it and disable it by default.
Make the single entry default and add a special
ARMV8_MULTIENTRY KConfig option to be used by the
platforms that need multientry and set it for the LS2085A.
Delete all use of the CPU_RELEASE_ADDR from the Vexpress64
boards as it is just totally unused and misleading, and
make it conditional in the generic start.S code.
This makes the Juno platform start U-Boot properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The way the PSCI DT update happens currently means we pull in
<asm/armv7.h> everywhere, including on ARMv8 and that in turn brings in
<asm/io.h> for some non-PSCI related things that header needs to deal
with.
To fix this, we rework the hook slightly. A good portion of
arch/arm/cpu/armv7/virt-dt.c is common looking and I hope that when PSCI
is needed on ARMv8 we can re-use this by and large. So rename the
current hook to psci_update_dt(), move the prototype to <asm/psci.h> and
add an #ifdef that will make re-use later easier.
Reported-by: York Sun <yorksun@freescale.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: York Sun <yorksun@freescale.com>
For ARM architecture, enable the CONFIG_USE_ARCH_MEMSET/MEMCPY,
will highly increase the memset/memcpy performance. This is able
thanks to the ARM multiple register instructions.
Unfortunatelly the relocation is done without the cache enabled,
so it takes some time, but zeroing the BSS memory takes much more
longer, especially for the configs with big static buffers.
A quick test confirms, that the boot time improvement after using
the arch memcpy for relocation has no significant meaning.
The same test confirms that enable the memset for zeroing BSS,
reduces the boot time.
So this patch enables the arch memset for zeroing the BSS after
the relocation process. For ARM boards, this can be enabled
in board configs by defining: 'CONFIG_USE_ARCH_MEMSET'.
This was tested on Trats2.
A quick test with trace. Boot time from start to main_loop() entry:
- ~1384ms - before this change
- ~888ms - after this change
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
For some assemblers, they use another character as newline in a macro
(e.g. arc uses '`'), so for generic assembly code, need use ASM_NL (a
macro) instead of ';' for it.
Basically this is the same patch as applied to Linux kernel -
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/include/linux/linkage.h?id=9df62f054406992ce41ec4558fca6a0fa56fffeb
but modified a bit to fit in U-Boot.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
The 'nandecc sw' command selects a software-based error correction
algorithm. By default, this is OMAP_ECC_HAM1_CODE_SW but some
platforms use OMAP_ECC_BCH8_CODE_HW_DETECTION_SW as their
software-based correction algorithm. Allow a user to be specific e.g.
# nandecc sw <hamming|bch8>
where 'hamming' is still the default.
Note: we don't just use CONFIG_NAND_OMAP_ECCSCHEME as it might be set
to a hardware-based ECC scheme---a little strange when the user
has requested 'sw' ECC.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
This patch extends OMAP3 support for AM/DM37xx and
introduces the AM3703-based Quipos Cairo board.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Reviewed-by: Simon Glass <sjg@chromium.org>
esbc_validate command uses various IP Blocks: Security Monitor, CAAM block
and SFP registers. Hence the respective CONFIG's are enabled.
Apart from these CONFIG_SHA_PROG_HW_ACCEL and CONFIG_RSA are also enabled.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale sfp has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the CCSR defintion of
sfp_regs to common include. This patch also defines ccsr_sfp_regs
definition for newer versions of SFP.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
According to table 2-3 on page 87 of Marvell's latest PXA270
Specification Update Rev. I from 2010.04.19 [1] there exists a breed of
chips with a new CPU ID for PXA270M A1 stepping which our latest
Colibri PXA270 V2.4A modules actually have assembled. This patch helps
in correctly identifying those chips upon boot as well which then looks
as follows:
CPU: Marvell PXA27xM rev. A1
[1] http://www.marvell.com/application-processors/pxa-family/assets/pxa_27x_spec_update.pdf
Acked-by: Marek Vasut <marex@denx.de>
commit d9f43c8f5c sets
get_reset_cause() as static, but this conflicts with mx5
where its prototype is in sys_proto.h.
Drop it from sys_proto.h and drop print_cpuinfo from mx53_loco,
factorizing the call for this board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Import DTS for Arria V development kit and enable support
for DT. The DT is imported from Linux 3.19-rc1 as of commit
97bf6af1f928216fd6c5a66e8a57bfa95a659672 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Import DTS for Cyclone V development kit and enable support
for DT. The DT is imported from Linux 3.19-rc1 as of commit
97bf6af1f928216fd6c5a66e8a57bfa95a659672 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Add support for the Altera Arria V development kit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Currently in some cases SDRAM init requires global_data to be available
and soon this will not be available prior to board_init_f(). Adjust the
code paths in these cases to be correct. In some cases we had the SPL
stack be in DDR as we might have large stacks (due to Falcon Mode +
Environment). In these cases switch to CONFIG_SPL_STACK_R. In other
cases we had simply been setting CONFIG_SPL_STACK into SRAM. In these
cases we no longer need to (CONFIG_SYS_INIT_SP_ADDR is used and is also
in SRAM) so drop those lines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested on Beagleboard, Beagleboard xM
Tested-by: Matt Porter <mporter@konsulko.com>
Tested on Beaglebone Black, AM43xx GP EVM, OMAP5 uEVM, OMAP4 Pandaboard
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present SPL uses a single stack, either CONFIG_SPL_STACK or
CONFIG_SYS_INIT_SP_ADDR. Since some SPL features (such as MMC and
environment) require a lot of stack, some boards set CONFIG_SPL_STACK to
point into SDRAM. They then set up SDRAM very early, before board_init_f(),
so that the larger stack can be used.
This is an abuse of lowlevel_init(). That function should only be used for
essential start-up code which cannot be delayed. An example of a valid use is
when only part of the SPL code is visible/executable, and the SoC must be set
up so that board_init_f() can be reached. It should not be used for SDRAM
init, console init, etc.
Add a CONFIG_SPL_STACK_R option, which allows the stack to be moved to a new
address before board_init_r() is called in SPL.
The expected SPL flow (for CONFIG_SPL_FRAMEWORK) is documented in the README.
Signed-off-by: Simon Glass <sjg@chromium.org>
For version 1:
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Use the full driver model GPIO and serial drivers in SPL now that these are
supported. Since device tree is not available they will use platform data.
Remove the special SPL GPIO function as it is no longer needed.
This is all in one commit to maintain bisectability.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is already set up in crt0.S. We don't need a new structure and don't
really want one in the 'data' section of the image, since it will be empty
and crt0.S's changes will be ignored.
As an interim measure, remove it only if CONFIG_DM is not defined. This
allows us to press ahead with driver model in SPL and allow the stragglers
to catch up.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function has grown into something of a monster. Some boards are setting
up a console and DRAM here in SPL. This requires global_data which should be
set up in one place (crt0.S).
There is no need for SPL to use s_init() for anything since board_init_f()
is called immediately afterwards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Modify CONFIG_USB_MAX_CONTROLLER_COUNT value to 1 on P1022DS.
As ETSEC2 and USB2 are muxed; thus if ETSEC2 is enabled, the
system bus hangs on USB2 if ETSEC2 is enabled but "usb start"
command is issued. Hence making default controller count to 1
to avoid system hang.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: Yusong Sun <yorksun@freescale.com>
The code provides framework for heterogeneous multicore chips based on StarCore
and Power Architecture which are chasis-2 compliant, like B4860 and B4420
It will make u-boot recognize all non-ppc cores and peripherals like
SC3900/DSP CPUs, MAPLE, CPRI and print their configuration in u-boot logs.
Example boot logs of B4860QDS:
U-Boot 2015.01-00232-geef6e36-dirty (Jan 19 2015 - 11:58:45)
CPU0: B4860E, Version: 2.2, (0x86880022)
Core: e6500, Version: 2.0, (0x80400120)
Clock Configuration:
CPU0:1600 MHz, CPU1:1600 MHz, CPU2:1600 MHz, CPU3:1600 MHz,
DSP CPU0:1200 MHz, DSP CPU1:1200 MHz, DSP CPU2:1200 MHz, DSP CPU3:1200 MHz,
DSP CPU4:1200 MHz, DSP CPU5:1200 MHz,
CCB:666.667 MHz,
DDR:933.333 MHz (1866.667 MT/s data rate) (Asynchronous), IFC:166.667 MHz
CPRI:600 MHz
MAPLE:600 MHz, MAPLE-ULB:800 MHz, MAPLE-eTVPE:1000 MHz
FMAN1: 666.667 MHz
QMAN: 333.333 MHz
Top level changes include:
(1) Top level CONFIG to identify HETEROGENUOUS clusters
(2) CONFIGS for SC3900/DSP components
(3) Global structures like "cpu_type" and "MPC85xx_SYS_INFO"
updated for dsp cores and other components
(3) APIs to get DSP num cores and their Mask like:
cpu_dsp_mask, cpu_num_dspcores etc same as that of PowerPC
(5) Code to fetch and print SC cores and other heterogenous
device's frequencies
(6) README added for the same
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This fixes the MMC/SD card detect GPIOs for Apalis T30 which got broken
by the following commit:
2b2b50bc87 "dm: tegra: dts: Use TEGRA_GPIO() macro for all GPIOs"
While at it also re-add the comments describing which particular
Apalis/Colibri pins those GPIOs are on.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
All boards with a SPI interface have a suitable spi alias except Apalis
T30. Add these missing aliases just as the following commit did for the
others:
d2f60f9332 "dm: tegra: dts: Add aliases for spi on tegra30 boards"
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch incorporates a few fixes from Tom Warren <twarren@nvidia.com>.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra210 has a per-pin option named e_io_hv, which indicates that the
pin's input path should be configured to be 3.3v-tolerant. Add support
for this.
Note that this is very similar to previous chip's rcv_sel option.
However, since the Tegra TRM names this option differently for the
different chips, we support the new name so that the code exactly matches
the naming in the TRM, to avoid confusion.
This patch incorporates a few fixes from Tom Warren <twarren@nvidia.com>.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra210 starts its drive group registers at a different offset from the
APB MISC register block that other SoCs. Update the code to handle this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
T210 support HSM and Schmitt options in the pinmux register (previous
chips placed these options in the drive group register). Update the
code to handle this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra210 moves some bits around in the pinmux registers. Update the code
to handle this.
This doesn't attempt to address the issues with the group-to-group varying
drive group register layout mentioned earlier. This patch handles the
SoC-to-SoC differences in the mux register layout.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On some future SoCs, some per-drive-group features became per-pin
features. Move all type definitions early in the header so they can
be enabled irrespective of the setting of TEGRA_PMX_SOC_HAS_DRVGRPS.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On some future SoCs, some of the per-drive-group features no longer
exist. Add some ifdefs to support this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Future SoCs have a slightly different combination of pinmux options per
pin. This will be simpler to handle if we simply have one define per
option, rather than grouping various options together, in combinations
that don't align with future chips.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra's drive group registers have a remarkably inconsistent layout. The
current U-Boot driver doesn't take this into account at all. Add a
comment to describe the issue, so at least anyone debugging the driver
will be aware of this. To solve this, we'd need to add a per-drive-group
data structure describing the layout for the individual register. Since
we don't set up too many drive groups in U-Boot at present, this
hopefully isn't causing too much practical issue. Still, we probably need
to fix this sometime.
Wth Tegra210, the register layout becomes almost entirely consistent, so
this problem partially solves itself over time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is needed to correctly apply the new Jetson TK1 pinmux config.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When the CPU is in non-secure (NS) mode (when running U-Boot under a
secure monitor), certain actions cannot be taken, since they would need
to write to secure-only registers. One example is configuring the ARM
architectural timer's CNTFRQ register.
We could support this in one of two ways:
1) Compile twice, once for secure mode (in which case anything goes) and
once for non-secure mode (in which case certain actions are disabled).
This complicates things, since everyone needs to keep track of
different U-Boot binaries for different situations.
2) Detect NS mode at run-time, and optionally skip any impossible actions.
This has the advantage of a single U-Boot binary working in all cases.
(2) is not possible on ARM in general, since there's no architectural way
to detect secure-vs-non-secure. However, there is a Tegra-specific way to
detect this.
This patches uses that feature to detect secure vs. NS mode on Tegra, and
uses that to:
* Skip the ARM arch timer initialization.
* Set/clear an environment variable so that boot scripts can take
different action depending on which mode the CPU is in. This might be
something like:
if CPU is secure:
load secure monitor code into RAM.
boot secure monitor.
secure monitor will restart (a new copy of) U-Boot in NS mode.
else:
execute normal boot process
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some systems have so much RAM that the end of RAM is beyond 4GB. An
example would be a Tegra124 system (where RAM starts at 2GB physical)
that has more than 2GB of RAM.
In this case, we want gd->ram_size to represent the actual RAM size, so
that the actual RAM size is passed to the OS. This is useful if the OS
implements LPAE, and can actually use the "extra" RAM.
However, we can't use get_ram_size() to verify the actual amount of RAM
present on such systems, since some of the RAM can't be accesses, which
confuses that function. Avoid calling get_ram_size() when the RAM size
is too large for it to work correctly. It's never actually needed anyway,
since there's no reason for the BCT to report the wrong RAM size.
In systems with >=4GB RAM, we still need to clip the reported RAM size
since U-Boot uses a 32-bit variable to represent the RAM size in bytes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
size_mb is used to hold a value that's sometimes KB, sometimes MB,
and sometimes bytes. Use separate correctly named variables to avoid
confusion here. Also fix indentation of a conditional statement.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add basic Xilinx ZynqMP arm64 support.
Serial and SD is supported.
It supports emulation platfrom ep108 and QEMU.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With a389531 we now call readl() from this file so add <asm/io.h> so
that we have a prototype for the function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Freescale's SEC block has built-in Data Encryption
Key(DEK) Blob Protocol which provides a method for
protecting a DEK for non-secure memory storage.
SEC block protects data in a data structure called
a Secret Key Blob, which provides both confidentiality
and integrity protection.
Every time the blob encapsulation is executed,
a AES-256 key is randomly generated to encrypt the DEK.
This key is encrypted with the OTP Secret key
from SoC. The resulting blob consists of the encrypted
AES-256 key, the encrypted DEK, and a 16-bit MAC.
During decapsulation, the reverse process is performed
to get back the original DEK. A caveat to the blob
decapsulation process, is that the DEK is decrypted
in secure-memory and can only be read by FSL SEC HW.
The DEK is used to decrypt data during encrypted boot.
Commands added
--------------
dek_blob - encapsulating DEK as a cryptgraphic blob
Commands Syntax
---------------
dek_blob src dst len
Encapsulate and create blob of a len-bits DEK at
address src and store the result at address dst.
Signed-off-by: Raul Cardenas <Ulises.Cardenas@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Ulises Cardenas <ulises.cardenas@freescale.com>
Signed-off-by: Ulises Cardenas-B45798 <Ulises.Cardenas@freescale.com>
Since commit 3ff46cc42b ("arm: relocate the exception vectors") mx35
does not boot anymore.
Add a specific relocate_vectors macro that skips the vector relocation, as the
i.MX35 SoC does not provide RAM at the high vectors address (0xFFFF0000), and
(0x00000000) maps to ROM.
This allows mx35 to boot again.
Cc: Sebastian Priebe <sebastian.priebe@cadcon.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Since commit 3ff46cc42b ("arm: relocate the exception vectors") mx31
does not boot anymore.
Add a specific relocate_vectors macro that skips the vector relocation, as the
i.MX31 SoC does not provide RAM at the high vectors address (0xFFFF0000), and
(0x00000000) maps to ROM.
This allows mx31 to boot again.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If CONFIG_ARMV7_PSCI is not defined and CONFIG_ARMV7_SECURE_BASE is defined,
smp_kicl_all_cpus may enable secondary cores and runs into secure_ram_addr(
_smp_pen), before code is relocated to secure ram.
So need relocation to secure ram before enable secondary cores.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Each way of the system cache has 256 entries for PH1-Pro4 and older
SoCs, whereas 512 entries for PH1-Pro5 and newer SoCs. The line
size is still 128 byte. Thus, the way size is 32KB/64KB for old/new
SoCs.
To keep lowlevel_init SoC-independent, set BOOT_RAM_SIZE to the
constant value 32KB. It is large enough for temporary RAM and
should work for all the SoCs of UniPhier family.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This function was intended for MN2WS0235 (what we call PH1-Pro4TV).
On that SoC, MPLL is already running on the power-on reset and it
makes sense to stop the PLL at early boot-up.
On the other hand, PH1-Pro4(R) does not have SC_MPLLOSCCTL register,
so this function has no point.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This code is duplicated in ph1-ld4/sg_init.c and ph1-pro4/sg_init.c.
Merge the same code into a new file, memconf.c.
The helper functions no longer have to be placed in the header file.
Also, move them into memconf.c.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Two support card variants are used with UniPhier reference boards:
- 1 chip select support card (original CPLD)
- 3 chip selects support card (ARIMA-compatible CPLD)
Currently, the former is only supported on PH1-Pro4, but it can be
expanded to PH1-LD4, PH1-sLD8 with a little code change.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Each USB port corresponds to the following IP core:
port0: xHCI (0x65a00000) SS+HS
port1: xHCI (0x65c00000) HS (SS PHY is not implemented)
port2: EHCI (0x5a800100) HS
port3: EHCI (0x5a810100) HS
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
EHCI host controllers have a common register interface.
We may wish to implement a generic EHCI driver someday.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Because uniphier_ehci_reset() is only called from ehci-uniphier.c,
it can be a static function there.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Now UniPhier platform highly depends on Device Tree configuration
(CONFIG_OF_CONTROL is select'ed by Kconfig). Since the EHCI is only
used on main U-Boot, we can drop platform devices of the EHCI
controllers. We still keep UART platform devices because they might
be useful for SPL.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Deassert the reset signal and provide the clock for STDMAC core.
This is necessary for the USB 2.0 host controllers.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
For all the UniPhier SoCs so far, the reset signal of the NAND core
is automatically deasserted after the PLL gets stabled.
(The bit 2 of SC_RSTCTRL is default to one.)
This causes a fatal problem on the NAND controller of PH1-LD4.
For that SoC, the NAND I/O pins are not set up yet at the power-on
reset except the NAND boot mode. As a result, the NAND controller
begins automatic device scanning with wrong I/O pins and finally
hangs up.
Actually, U-Boot dies after printing "NAND:" on the console unless
the boot mode latch detected the NAND boot mode.
To work around this problem, reset the NAND core in SPL for non-NAND
boot modes. If CONFIG_NAND_DENALI is enabled, the reset signal is
deasserted again in U-Boot proper. At this time, I/O pins have been
correctly set up, the device scanning should succeed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Split the current clkrst_init() into two functions:
- early_clkrst_init(): called from SPL
Deassert the reset signals of the memory controller and some other
basic cores.
- clkrst_init(): called from main U-boot
Deassert the reset signals that are necessary for the access to
peripherals etc.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now UniPhier SoCs only work with CONFIG_SPL and the function
sbc_init() is called from SPL.
The conditional #if !defined(CONFIG_SPL_BUILD) has no point
any more.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since commit 0e7368c6c4 (kbuild: prepare for moving headers into
mach-*/include/mach), we can replace #include <asm/arch/*.h> with
<mach/*.h> so we do not need to create the symbolic link during the
build.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
It was found that the L2 cache timings that we had before could cause
freezes and hangs. We should make things more robust with better
timings. Currently the production ChromeOS kernel applies these
timings, but it's nice to fixup firmware too (and upstream probably
won't take our kernel hacks).
This also provides a big cleanup of the L2 cache init code avoiding
some duplication. The way things used to work:
* low_power_start() was installed by the SPL (both at boot and resume
time) and left resident in iRAM for the kernel to use when bringing
up additional CPUs. It used configure_l2_ctlr() and
configure_l2_actlr() when it detected it was on an A15. This was
needed (despite the L2 cache registers being shared among all A15s)
because we might have been the first man in after the whole A15
cluster was shutdown.
* secondary_cores_configure() was called on at boot time and at resume
time. Strangely this called configure_l2_ctlr() but not
configure_l2_actlr() which was almost certainly wrong. Given that
we'll call both (see next bullet) later in the boot process it
didn't matter for normal boot, but I guess this is how L2 cache
settings got set on 5420/5800 (but not 5250?) at resume time.
* exynos5_set_l2cache_params() was called as part of cache enablement.
This should happen at boot time (normally in the SPL except for USB
boot where it happens in main U-Boot).
Note that the old code wasn't setting ECC/parity in the cache
enablement code but we happened to get it anyway because we'd call
secondary_cores_configure() at boot time. For resume time we'd get it
anyway when the 2nd A15 core came up.
Let's make this a whole lot simpler. Now we always set these
parameters in the same place for all boots and use the same code for
setting up secondary CPUs.
Intended net effects of this change (other than cleanup):
* Timings go from before:
data: 0 cycle setup, 3 cycles (0x2) latency
tag: 0 cycle setup, 3 cycles (0x2) latency
after:
data: 1 cycle setup, 4 cycles (0x3) latency
tag: 1 cycle setup, 4 cycles (0x3) latency
* L2ACTLR is properly initted on 5420/5800 in all cases.
One note is that we're still relying on luck to keep low_power_start()
working. The compiler is being nice and not storing anything on the
stack.
Another note is that on its own this patch won't help to fix cache
settings in an RW U-Boot update where we still have the RO SPL. The
plan for that is:
* Have RW U-Boot re-init the cache right before calling the kernel
(after it has turned the L2 cache off). This is why the functions
are in a header file instead of lowlevel_init.c.
* Have the kernel save the L2 cache settings of the boot CPU and apply
them to all other CPUs. We get a little lucky here because the old
code was using "|=" to modify the registers and all of the bits that
it's setting are also present in the new settings (!). That means
that when the 2nd CPU in the A15 cluster comes up it doesn't
actually mess up the settings of the 1st CPU in the A15 cluster. An
alternative option is to have the kernel write its own
low_power_start() code.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
On warm reset, all cores jump to the low_power_start function because iRAM
data is retained and because while executing iROM code all cores find
the jump flag 0x02020028 set. In low_power_start, cores check the reset
status and if true they clear the jump flag and jump back to 0x0.
The A7 cores do jump to 0x0 but consider following instructions as a Thumb
instructions which in turn makes them loop inside the iROM code instead of
jumping to power_down_core.
This issue is fixed by replacing the "mov pc" instruction with a "bx"
instruction which switches state along with the jump to make the execution
unit consider the branch target as an ARM instruction.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When compiled SPL for Thumb secondary cores failed to boot
at the kernel boot up. Only one core came up out of 4.
This was happening because the code relocated to the
address 0x02073000 by the primary core was an ARM asm
code which was executed by the secondary cores as if it
was a thumb code.
This patch fixes the issue of secondary cores considering
relocated code as Thumb instructions and not ARM instructions
by jumping to the relocated with the help of "bx" ARM instruction.
"bx" instruction changes the 5th bit of CPSR which allows
execution unit to consider the following instructions as ARM
instructions.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch does 3 things:
1. Enables ECC by setting 21st bit of L2CTLR.
2. Restore data and tag RAM latencies to 3 cycles because iROM sets
0x3000400 L2CTLR value during switching.
3. Disable clean/evict push to external by setting 3rd bit of L2ACTLR.
We need to restore this here due to switching.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
L2 Auxiliary Control Register provides configuration
and control options for the L2 memory system. Bit 3
of L2ACTLR stands for clean/evict push to external.
Setting bit 3 disables clean/evict which is what
this patch intends to do.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
iROM logic provides undesired jump address for CPU2.
This patch adds a programmable susbstitute for a part of
iROM logic which wakes up cores and provides jump addresses.
This patch creates a logic to make all secondary cores jump
to a particular address which evades the possibility of CPU2
jumping to wrong address and create undesired results.
Logic of the workaround:
Step-1: iROM code checks value at address 0x2020028.
Step-2: If value is 0xc9cfcfcf, it jumps to the address (0x202000+CPUid*4),
else, it continues executing normally.
Step-3: Primary core puts secondary cores in WFE and store 0xc9cfcfcf in
0x2020028 and jump address (pointer to function low_power_start)
in (0x202000+CPUid*4).
Step-4: When secondary cores recieve event signal they jump to this address
and continue execution.
Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds workaround for the ARM errata 799270 which says
"If the L2 cache logic clock is stopped because of L2 inactivity,
setting or clearing the ACTLR.SMP bit might not be effective. The bit is
modified in the ACTLR, meaning a read of the register returns the
updated value. However the logic that uses that bit retains the previous
value."
Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds workaround for ARM errata 798870 which says
"If back-to-back speculative cache line fills (fill A and fill B) are
issued from the L1 data cache of a CPU to the L2 cache, the second
request (fill B) is then cancelled, and the second request would have
detected a hazard against a recent write or eviction (write B) to the
same cache line as fill B then the L2 logic might deadlock."
Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds code to shutdown secondary cores.
When U-boot comes up, all secondary cores appear powered on,
which is undesirable and causes side effects while
initializing these cores in kernel.
Secondary core power down happens in following steps:
Step-1: After Exynos power-on, primary core starts executing first.
Step-2: In iROM code every core has to check 2 flags i.e.
addresses 0x02020028 & 0x02020004.
Step-3: Initially 0x02020028 is 0 for all cores and 0x02020004 has a
jump address for primary core and 0 for all secondary cores.
Step-4: Therefore, primary core follows normal iROM execution and jumps
to BL1 eventually, whereas all secondary cores enter WFE.
Step-5: When primary core comes into function secondary_cores_configure,
it puts pointer to function power_down_core into 0x02020004
and provides DSB and SEV for all cores so that they may come out
of WFE and jump to power_down_core function.
Step-6: And ultimately because of power_down_core all
secondary cores shut-down.
Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
ED Mini V2 is based on Orion 5x which boots at fixed
address 0xFFFF0000 in NOR Flash. Place SPL there, and
switch U-Boot from .bin to .img format, stored in
NOR Flash at 0xFFF90000.
Note: this patch was tested on HW and works, i.e.
it boots U-Boot properly, but SPL console output
currently does not appear, due to GD being trashed
by arch/arm/lib/spl.c. This trashing is soon to be
removed, and then ED Mini V2 SPL console output will
become visible.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Porter is an entry level development board based on R-Car M2 SoC (R8A7791)
This commit supports the following peripherals:
- SCIF, I2C, Ethernet, QSPI, SD, USB Host
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Now this feature works. Let's turn it on by default so we do not
depend on specific tool-chains.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SuperH is supposed to support the Private Library feature, but it is
actually not working.
If CONFIG_USE_PRIVATE_LIBGCC is enabled, the build fails for the
undefined references to '__sdivsi3_i4i' and '__udivsi3_i4i'.
To fix this error, import missing libraries from Linux 3.19
and adjust them for U-Boot:
- Remove "#include <linux/module.h>" and "EXPORT_SYMBOL(...)"
- Use SPDX-License-Identifier
- Remove white space
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Rename two files to the corresponding file names in Linux.
This helps us find missing libraries in the next commit.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lager board has two SDHI port as SDHI0 and SDHI2.
This adds GPIO configuration and initialization function of SDHI, and
enables MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Alt board has two SDHI port.
This adds GPIO configuration and initialization function of SDHI, and
enables MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chan-Taek Park <c-park@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Po-Yu Chuang <ratbert@faraday-tech.com>
Acked-by: Marek Vasut <marex@denx.de>
These are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
Acked-by: Marek Vasut <marex@denx.de>
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Lei Wen <leiwen@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Matthias Weisser <weisserm@arcor.de>
Acked-by: Marek Vasut <marex@denx.de>
Now CONFIG_SPL_BUILD is not defined in Kconfig, so
"!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
When Kconfig for U-boot was examined, one of the biggest issues was
how to support multiple images (Normal, SPL, TPL). There were
actually two options, "single .config" and "multiple .config".
After some discussions and thought experiments, I chose the latter,
i.e. to create ".config", "spl/.config", "tpl/.config" for Normal,
SPL, TPL, respectively.
It is true that the "multiple .config" strategy provided us the
maximum flexibility and helped to avoid duplicating CONFIGs among
Normal, SPL, TPL, but I have noticed some fatal problems:
[1] It is impossible to share CONFIG options across the images.
If you change the configuration of Main image, you often have to
adjust some SPL configurations correspondingly. Currently, we
cannot handle the dependencies between them. It means one of the
biggest advantages of Kconfig is lost.
[2] It is too painful to change both ".config" and "spl/.config".
Sunxi guys started to work around this problem by creating a new
configuration target. Commit cbdd9a9737 (sunxi: kconfig: Add
%_felconfig rule to enable FEL build of sunxi platforms.) added
"make *_felconfig" to enable CONFIG_SPL_FEL on both images.
Changing the configuration of multiple images in one command is a
generic demand. The current implementation cannot propose any
good solution about this.
[3] Kconfig files are getting ugly and difficult to understand.
Commit b724bd7d63 (dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to
Kconfig) has sprinkled "if !SPL_BUILD" over the Kconfig files.
[4] The build system got more complicated than it should be.
To adjust Linux-originated Kconfig to U-Boot, the helper script
"scripts/multiconfig.sh" was introduced. Writing a complicated
text processor is a shell script sometimes caused problems.
Now I believe the "single .config" will serve us better. With it,
all the problems above would go away. Instead, we will have to add
some CONFIG_SPL_* (and CONFIG_TPL_*) options such as CONFIG_SPL_DM,
but we will not have much. Anyway, this is what we do now in
scripts/Makefile.spl.
I admit my mistake with my apology and this commit switches to the
single .config configuration.
It is not so difficult to do that:
- Remove unnecessary processings from scripts/multiconfig.sh
This file will remain for a while to support the current defconfig
format. It will be removed after more cleanups are done.
- Adjust some makefiles and Kconfigs
- Add some entries to include/config_uncmd_spl.h and the new file
scripts/Makefile.uncmd_spl. Some CONFIG options that are not
supported on SPL must be disabled because one .config is shared
between SPL and U-Boot proper going forward. I know this is not
a beautiful solution and I think we can do better, but let's see
how much we will have to describe them.
- update doc/README.kconfig
More cleaning up patches will follow this.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is true that malloc is necessary for Driver Model before
relocation, but there is no good reason to reserve the malloc
space more than enough. The default value 0x400 works well.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There 4 JRs, 4 RTICs and 8 DECOs, and set them the same stream id
for using the same SMMU3 on LS1021A.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The RCPM FSM may not be reset after power-on, for example,
in the cases of cold boot and wakeup from deep sleep.
It causes cache coherency problem and may block deep sleep.
Therefore, reset them if they are not be reset.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1021A's PCIe1 region begins 0x40_00000000; PCIe2 begins
0x48_00000000. In order to access PCIe device, we must create
TLB to map the 40bit physical address to 32bit virtual address.
This patch will enable MMU after DDR is available and creates MMU
table in DRAM to map all 4G space; then, re-use the reserved space
to map PCIe region. The following the mapping layout.
VA mapping:
------- <---- 0GB
| |
| |
|-------| <---- 0x24000000
|///////| ===> 192MB VA map for PCIe1 with offset 0x40_0000_0000
|-------| <---- 0x300000000
| |
|-------| <---- 0x34000000
|///////| ===> 192MB VA map for PCIe2 with offset 0x48_0000_0000
|-------| <---- 0x40000000
| |
|-------| <---- 0x80000000 DDR0 space start
|\\\\\\\|
|\\\\\\\| ===> 2GB VA map for 2GB DDR0 Memory space
|\\\\\\\|
------- <---- 4GB DDR0 space end
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch is to define default values for some CCSR macros
to make header files cleaner.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Upgrade Manage Complex (MC) flib API to 0.5.2. Rename directory
fsl_mc to fsl-mc. Change the fsl-mc node in Linux device tree
from "fsl,dprcr" to "fsl-mc". Print MC version info when
appropriate.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
FSL-LSCH3 platforms can have multiple DDR clocks. LS2085A has one clock for
general DDR controlers, and another clock for DP-DDR. DDR driver needs to
change to support multiple clocks.
Signed-off-by: York Sun <yorksun@freescale.com>
This patch adds the fdt-fixup logic for the clock frequency of the
NS16550A related device tree nodes.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Flushing L3 cache in CCN-504 requries d-cache to be disabled. Using
assembly function to guarantee stack is not used before flushing is
completed. Timeout is needed for simualtor on which CCN-504 is not
implemented. Return value can be checked for timeout situation.
Change bootm.c to disable dcache instead of simply flushing, required
by flushing L3.
Signed-off-by: York Sun <yorksun@freescale.com>
U-Boot should only add "enable-method" and "cpu-release-address"
properties to the "cpu" node of the online cores.
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
According to hardware implementation, a single outer shareable global
coherence group is defined. Inner shareable has not bee enabled.
Signed-off-by: York Sun <yorksun@freescale.com>
This patch ensures that the TZPC (BP147) and TZASC-400 programming
happens for LS2085A SoC only when the desired config flags are
enabled and ensures that the TZPC programming is done to allow Non-secure
(NS) + secure (S) transactions only for DCGF registers.
The TZASC component is not present on LS2085A-Rev1, so the TZASC-400
config flag is turned OFF for now.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The WaRP Board is a Wearable Reference Plaform. The board features:
- Freescale i.MX6 SoloLite processor with 512MB of RAM
- Freescale FXOS8700CQ 6-axis Xtrinsic sensor
- Freescale Kinetis KL16 MCU
- Freescale Xtrinsic MMA955xL intelligent motion sensing platform
The board implements a hybrid architecture to address the evolving
needs of the wearables market. The platform consists of a main board
and an example daughtercard with the ability to add additional
daughtercards for different usage models.
For more information about the project, visit:
http://www.warpboard.org/
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Older linux-sunxi-3.4 kernels override our PLL6 setting with 300 MHz,
halving the mbus frequency, so set it to 300 MHz ourselves and base the
mbus divider on that.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
USB doesn't seem to work yet; the controller detects the on-board Hub/
Ethernet device but can't read the descriptors from it. I haven't
investigated yet.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The bcm2835 and bcm2836 are essentially identical, except:
- The CPU is an ARM1176 v.s. a quad-core Cortex-A7.
- The physical address of many IO controllers has moved.
Rather than introducing a whole new bcm2836 value for $(SOC) or $(ARCH),
update the existing bcm2835 code to handle the minor differences, and
plumb it into the ARMv7 CPU architecture.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This commit adds $(srctree)/arch/arm/$(machdirs)/include/mach to
the headers search path.
It allows us to replace "#include <asm/arch/foo.h>" with
"#include <mach/foo.h>". As "#include <asm/arch/foo.h>" is still
supported, we can modify each file one by one.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Move
arch/arm/cpu/arm926ejs/kirkwood/* -> arch/arm/mach-kirkwood/*
Note:
Perhaps, can we merge arch/arm/mach-kirkwood and
arch/arm/mvebu-common into arch/arm/mach-mvebu, like Linux?
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
In U-boot, the directory structure, arch/$(ARCH)/cpu/$(CPU)/$(SOC)/
has been adopted except that $(CPU) is missing from some
architectures and $(SOC) is missing from some CPUs.
This structure did not fit very well in some cases.
[1] AT91
AT91 SoC family have been developed across some ARM processor
generations. Generally speaking, some IPs are often re-used in the
same SoC family (same SoC vendor) even when the main processor is
updated. As a result, a SoC-common directory is needed in the upper
level. Currently, AT91 source files are placed as follows:
arch/arm/cpu/arm920t/at91/*
arch/arm/cpu/arm926ejs/at91/*
arch/arm/cpu/armv7/at91/*
arch/arm/cpu/at91-common/*
Once directories are split, the motivation for refactorings across
CPU directories is lost. Some files in arm920t/at91/ and
arm926ejs/at91/ are so similar that they could be merged.
[2] Tegra
Tegra is a little bit special case where different CPUs are used for
SPL and the main U-boot. To obey the arch/$(ARCH)/cpu/$(CPU)/$(SOC)
structure, the source files must be placed across the CPUs,
again SoC-common directory is necessary in the upper level.
Moreover, there are several families in Tegra: Tegra20, Tegra30,
Tegra114, Tegra124. Here again, the tegra-common directory is needed
to contain commonly-used files.
Tegra directories have been sprinkled in the directory structure.
arch/arm/cpu/arm720t/tegra20
arch/arm/cpu/arm720t/tegra30
arch/arm/cpu/arm720t/tegra114
arch/arm/cpu/arm720t/tegra124
arch/arm/cpu/arm720t/tegra-common
arch/arm/cpu/armv7/tegra20
arch/arm/cpu/armv7/tegra30
arch/arm/cpu/armv7/tegra114
arch/arm/cpu/armv7/tegra124
arch/arm/cpu/armv7/tegra-common
arch/arm/cpu/tegra20-common
arch/arm/cpu/tegra30-common
arch/arm/cpu/tegra114-common
arch/arm/cpu/tegra124-common
arch/arm/cpu/tegra-common
As you see, splitting SoC code by the CPU is not going well,
especially for ARM.
Why don't we collect SoC-specific files into a single place?
A good example we can follow is Linux's arch/arm/mach-* structure.
This item was discussed in the following thread:
http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/188548/
Looks like I got some positive responses and we are almost ready to
start this movement.
This commit prepares arch/arm/Makefile for describing machdirs in it.
After this commit, we can move SoC directory to arch/arm/mach-$(SOC)
in simple steps although some cases such as AT91 and Tegra need more
fixes.
What we generally have to do is:
[1] Move files arch/arm/cpu/$(CPU)/$(SOC)/* to arch/arm/mach-$(SOC)/*
[2] Add machine entry into arch/arm/Makefile
[3] Remove "obj-y += $(SOC)" from arch/arm/cpu/$(CPU)/Makefile
[4] Fix the Kconfig file path in arch/arm/Kconfig
[5] Modify MAINTAINERS if necessary
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The board select menu in arch/arm/Kconfig is still big.
To slim down it, this commit moves AT91 boards to
arch/arm/mach-at91/Kconfig.
Also, consolidate "config SYS_SOC" in each board Kconfig.
The Kconfig files under board/ directory were modified with the
following command:
find board -name Kconfig | xargs sed -i -e '
/config SYS_SOC/ {
N
/default "at91"/ {
N
d
}
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.co>
Introduce arch_reserve_stacks() to tailor gd->start_addr_sp and gd->irq_sp to
the architecture needs.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Before avr32 had an extra storage for stack end to have a nice stack printout
on exception. Remove this extra storage and use generic gd->start_addr_sp
instead.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Prefix mmu.h PAGE_xxx definitions with MMU_ in order to prevent a naming
conflict with other definitions.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cpu_mmc_init() is required by the init sequence to have a working MMC interface
on avr32. This will not be included in the binary if we omit the avr32 board.c
when building the generic board.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The self-bias circuit is used by the bandgap during startup.
Once the bandgap has stabilized, the self-bias circuit should
be disabled for best noise performance of analog blocks.
Also this bit should be disabled before the chip enters STOP mode or
when ever the regular bandgap is disabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
The only LPC3250 board works fine with enabled generic board support,
add CONFIG_SYS_GENERIC_BOARD right into the arch config header.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
So that the CONFIG_SPL_FEL option is not needed anymore. And the regular
SPL binary, generated by the default u-boot build, is now also bootable
over USB in the FEL mode. The SPL still can boot from the SD card too.
A bunch of system registers need to be saved/restored in order to ensure
that the IRQ handler still works in the BROM FEL code after getting
control back from the SPL. This is done in the sunxi code instead of
abusing ifdefs in 'start.S'.
The decision whether to load the main u-boot binary from the SD card or
return to the FEL code in the BROM is done at runtime.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[hdegoede@redhat.com: Since we now restore various regs before returning to
the FEL BROM code we can drop the sunxi specific #ifdefs in start.S]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of
creating its own. There are some #ifdefs required in start.S. Future work
will hopefully remove these.
This series is available at u-boot-dm, branch sunxi-working.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some boards have a special way of loading U-Boot that does not fit with
the existing SPL code. For example sunxi uses an 'FEL' mode where U-Boot
is loaded over USB. Add a CONFIG option and boot mode for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The link register value can be required on some boards (e.g. FEL mode on
sunxi) so use a branch instruction to jump to save_boot_params() instead
of a branch link.
This requires a branch back to save_boot_params_ret so adjust the users
to deal with this. For exynos just drop the function since it doesn't
do anything.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Move the dram helper functions to a separate C file, rather then having them
as inline helpers in dram.h. This saves 144 bytes in the .text segment for
sun6i builds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
KS2 ddr3 initialization uses ddr3_size global variable before u-boot
relocation. Even if the variable is not being used after relocation,
writing to it corrupts relocation table.
This patch removes the global ddr3_size variable and uses local one
instead.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
When EMAC is in the boot order, the boot ROM sets OPP50 and the
MAC clock is set to /2. SPL needs to change it to /5 for Ethernet
to generate the correct txclk. This patch sets it correctly.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
The value in SDRAM_REF_CTRL controls the delay time between
the initial rising edge of DDR_RESETn to rising edge of DDR_CKE
(JEDEC specs this as 500us). In order to achieve this, SDRAM_REF_CTRL
should be written with a value corresponding to 500us delay before
starting DDR initialization sequence, and configure proper
value at the end of sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DDR3 timing and latency paramenters were not configured
correctly for 666MHz. Fixing the timing and latency values
according to Data sheet.
This fixes the random crashes seen on DRA72-evm.
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
An option is provided to avoid using SDL in U-Boot sandbox (and drop
support for the LCD). However the check in the Makefile is too late
and warnings are printed even if NO_SDL=y is given.
Adjust the order to avoid this warning.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
When a command is passed into sandbox using the '-c' argument the
command is run directly. This is most helpful when running tests (such
as test-dm.sh). Previously the exit code was an unused enum. Change it
to be the actual return code from the command so that the script calling
sandbox can know if the command succeeded (tests passed). Also remove
the now completely unused "exit_state" in sandbox.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since we have src, div and pre-div mask bits defined corresponding
to peripherals, calculation of clock specific to I2C appears
redundant and confusing. Using clk_bit_info struct we can write
calculations generic to all peripherals which makes code easy to
understand and free from peripheral specific exceptions.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We have assumed and kept mask bits for divider and pre-divider
as 0xf and 0xff, respectively. But these mask bits change from
one peripheral to another, and hence, need to be specified in
accordance with the peripherals.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Replacing SoC and peripheral specific function calls with generic
clock_get_periph_rate calls to get the peripheral clocks.
Also, removing dead code of peripheral and SoC specific function
implementations which was used earlier for fetching peripheral clocks.
This code is not being used anymore because of the introduction
of generic clock_get_periph_rate function.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
exynos5_get_periph_rate function reads incorrect div for
SDMMC2 & 3. It also reads prediv and does division only for
SDMMC0 & 2 when actually various other peripherals need that.
Adding changes to fix these mistakes in periph rate calculation.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We planned to fetch peripheral rate through one generic API per
peripheral. These generic peripheral functions are in turn
expected to fetch apt values from a function refactored as
per SoC versions. This patch adds support for fetching peripheral
rates for Exynos5420 and Exynos5800.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Moving exynos5420_get_pll_clk function definition up in the
code to keep it together with rest of SoC_get_pll_clk functions.
This makes code more legible and also removes the need of
declaration when called before the position of definition in
code. Also, renaming exynos5420_get_pll_clk to
exynos542x_get_pll_clk because it is being used for both Exynos
5420 and 5800.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Apparently, members of clk_bit_info array do not map correctly
to the members of enum periph_id. This mapping got broken after
we changed periph_id(s) to reflect interrupt number instead of
their position in a sequence. This patch intends to fix above
mentioned issue.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Exynos5420 has different registers with other exynos5 SoCs to control
usb device phy, so need separated function to enable exynos5420 usb
device phy.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This needs for special handling of nRESET_OUT line(GPD1-0 gpio) for eMMC
memory to perform complete reboot on Odroid XU3 board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This needs for special handling of nRESET_OUT line(GPK1-2 gpio) for eMMC
memory to perform complete reboot on Odroid X2/U3 boards.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The most exynos used the "Ratio + 1" as div value.
And value at register is "Ratio".
So if want to set exact value, it needs to subtract one.
Value at register ("Ratio") = div - 1
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
ARC HS and ARC EM are new cores based on ARCv2 ISA which is binary
incompatible with ISAv1 (AKA ARCompact).
Significant difference between ISAv2 and v1 is implementation of
interrupt vector table.
In v1 it is implemented in the same way as on many other architectures -
as a special location where user may put whether code executed in place
(if machine word of space is enough) or jump to a full-scale interrupt
handler.
In v2 interrupt table is just an array of adresses of real interrupt
handlers. That requires a separate section for IVT that is not encoded
as code by assembler.
This change adds support for following cores:
* ARC EM6 (simple 32-bit microcontroller without MMU)
* ARC HS36 (advanced 32-bit microcontroller without MMU)
* ARC HS38 (advanced 32-bit microcontroller with MMU)
As a part of ARC HS38 new version of MMU (v4) was introduced.
Also this change adds AXS131 board which is the same DW ARC SDP base board but
with ARC HS38 CPU tile.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
r8a7794 uses ARM SoC of CA7 base. If we want to use dcache on CA7, we
need to enable SMP bit of Auxiliary Control Register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SILK is an entry level development board based on R-Car E2 SoC (R8A7794)
This commit supports the following peripherals:
- SCIF, I2C, Ethernet, QSPI, MMC, USB Host
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
With driver model the number of PIO ports is defined by platform data, so
remove it from the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
These additional nodes need to be provided to get U-Boot to boot correctly
on the Canyonlands / Glacier board:
- chosen path to the console-uart
- reg-shift set to 0 in the uart device nodes
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Define an _end symbol indicating the end of u-boot.bin. Also add some dummy
words into the link script to ensure that u-boot.bin will always extend
that far. There may be a better way of doing this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is required at present for device tree control. The ppc4xx does support
GPIOs but does not seem to have a proper driver. So this file is empty.
Signed-off-by: Simon Glass <sjg@chromium.org>
The canyonlands.h config file works with canyonlands, glacier and arches
boards. Bring in the device tree files for these from Linux 3.17.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new ramboot config for glacier so that it is possible to test U-Boot
loaded over Ethernet instead of using JTAG.
Signed-off-by: Simon Glass <sjg@chromium.org>
Many CONFIG options have an unnecessary value of 1. CONFIG_440 is set in
the various board config files. Also simplify the CONFIG_440 check in
config.mk
Signed-off-by: Simon Glass <sjg@chromium.org>
When booting in JTAG mode, there is no way to use soft break-points, and
no way of knowing when SPL has finished executing (so the user can issue
a 'halt' command to load u-boot.bin for example)
Add a debug output and simple loop to stop execution at the completion of
the SPL initialisation as a pseudo break-point when booting in JTAG mode
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Section 4.1.2 of Freescale Application Note AN4199 describes the
configuration required to operate the mx28 from a 5V source without a
battery.
This patch changes the behaviour of the dropout control of the DC-DC
converter (refer to section 11.12.9 of the mx28 Application Processor
Reference Manual - Document Number: MCIMX28RM, Rev 2, 08/2013) to the
following:
- Always use 4P2 Linear Regulator if CONFIG_SYS_MXS_VDD5V_ONLY is defined
- Switch between 4P2 Linear Regulator and Battery, using whichever has
the highest voltage if CONFIG_SYS_MXS_VDD5V_ONLY isnot set (this is
the same as the pre-patch behaviour)
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Signed-off-by: Damien Gotfroi <dgotfroi@greenwatch.be>
It is difficult to track down fail to boot issues in the mxs SPL.
Implement the following to make it easier:
- Add debug outputs to allow tracing of SPL progress in order to track
where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must
be defined to enable debug output in SPL
- Add TODO comments where it is not clear if the code is doing what it
is meant to be doing, even tough the board boots properly (these comments
refer to existing code, not to any code added by this patch)
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Should use AIPS3 configuration address 0x0227C000 to set AIPS3,
not the AIPS3 base address.
Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with
AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem.
Signed-off-by: Ye.Li <B37916@freescale.com>
This patch has some parts connected together:
- Use _gd in bss section which is automatically cleared
Location at SPL_MALLOC_END wasn't cleared at all
- Use MALLOC_F_LEN(early alloc) instead of FULL MALLOC
(mem_malloc_init is not called at all)
- Simplify malloc and stack init.
At the end of SPL addr is malloc area and below is stack
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Because it is not compatible with DM where
malloc_base has to be available early and init
has to be done in ASM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Compile code with -fPIC to get GOT. Do not build SPL
with fPIC because it increasing SPL size for nothing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Setup gd from ASM to be availalbe for board_init_r.
Setting it up in spl_board_init is too late when
MALLOC is used.
Space for gd is located behind MALLOC area at the end of BRAM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not use specific macros for debugging.
Also remove compilation warning:
w+../arch/microblaze/cpu/interrupts.c: In function 'interrupt_handler':
w+../arch/microblaze/cpu/interrupts.c:153:2: warning: format '%x'
expects argument of type 'unsigned int', but argument 2 has type 'void
(*)(void *)' [-Wformat]
w+../arch/microblaze/cpu/interrupts.c:153:2: warning: format '%x'
expects argument of type 'unsigned int', but argument 4 has type 'void
*' [-Wformat]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not save registers below r1 stack pointer because
it is not checked by stack undeflow is not able to detect
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This way we may have very limited set of functions implemented so we
save some space.
Also it allows us to build U-Boot for any ARC core with the same one
toolchain because we don't rely on pre-built libgcc.
For example:
* we may use little-endian toolchain but build U-Boot for ether
endianess
* we may use non-multilibbed uClibc toolchain but build U-Boot for
whatever ARC CPU flavour that current GCC supports
Private libgcc built from generic C implementation contributes only 144
bytes to .text section so we don't see significant degradation of size:
--->8---
$ arc-linux-size u-boot.libgcc-prebuilt
text data bss dec hex filename
222217 24912 214820 461949 70c7d u-boot.libgcc-prebuilt
$ arc-linux-size u-boot.libgcc-private
text data bss dec hex filename
222361 24912 214820 462093 70d0d u-boot.libgcc-private
--->8---
Also I don't notice visible performance degradation compared to
pre-built libgcc (where at least "*div*" functions are had-written in
assembly) on typical operations of downloading 10Mb uImage over TFTP and
bootm.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As a preparation to ARCv2 port submission we're moving CPU slection
flags to a common location.
Also it will allow us to have more flexible CPU specification, not only
ISA version but CPU family as well checking CONFIG_ARC_CPU_xxx.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Common arch_early_init_r() is used in "arc/lib/cpu.c" for all ARC boards
so there's no sense in separate per-board definitions.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
There're no other options for ARC except "generic board" so ther's no
point to define CONFIG_SYS_GENERIC_BOARD per board.
We now have it set fo all ARC boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This change allows to keep board description clean and minimalistic.
This is especially helpful if one board may house different CPUs with
different features.
It is applicable to both FPGA-based boards or those that have CPUs
mounted on interchnagable daughter-boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This change allows to keep board description clean and minimalistic.
This is especially helpful if one board may house different CPUs with
different features.
It is applicable to both FPGA-based boards or those that have CPUs
mounted on interchnagable daughter-boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Now we may select a particular version of ARC700:
* ARC750D or
* ARC770D
It allows more flexible (or more fine tuned) configuration of U-Boot.
Before that change we relied on minimal configuration but now we may
use specific features of each CPU.
Moreover allows us to escape manual selection of options that
exist in both CPUs but may have say different version like MMUv2 in
ARC750D vs MMUv3 in ARC770D.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
It's prohibited to put branch instruction in the very end of zero-delay
loop. On execution this causes "Illegal instruction" exception.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
As the at91cap9adk board is removed by commit: b5508344
(ARM: remove broken "at91cap9adk" board), so the at91cap9
code is not used anymore, and also the document for
at91cap9 can not be found on www.atmel.com, so remove the
at91cap9 related code.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Some SoC need to redirect the saic to aic to make the interrupt to
work, here add a weak function to be replaced by real function.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
The SFR (special function registers) can be shared bwteen
sama5d3 and sama5d4 soc.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[whitespace adoptions for 80 char compliance]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This matrix header file can be shared between sama5d3 and sama5d4 soc.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[whitespace adaptions for 80 char compliance]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Space is used before 'default' in PCIE_ECAM_BASE in arch/x86/Kconfig
so it looks misaligned. Replace the space with tab to indent.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Galileo board has a microSD slot which is routed from Quark SoC
SDIO controller. Enable SD/MMC support so that we can use an SD card.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Quark SoC contains a legacy SPI controller in the legacy bridge
which is ICH7 compatible. Like Tunnel Creek and BayTrail, the BIOS
control register offset in the ICH SPI driver is wrong for the Quark
SoC too, unprotect_spi_flash() is added to enable the flash write.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC has a legacy GPIO block in the legacy bridge (D0:F31),
which is just the same one found in other x86 chipset. Since we
programmed the GPIO register block base address, we should be
able to enable the GPIO support on Intel Galileo board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC has some non-standard BARs (excluding PCI standard BARs)
which need be initialized with suggested values. This includes GPIO,
WDT, RCBA, PCIe ECAM and some ACPI register block base addresses.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we have added Quark MRC codes, call MRC in dram_init() so
that DRAM can be initialized on a Quark based board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
For some unknown reason, the TSC calibration via PIT does not work on
Quark. Enable bypassing TSC calibration and override TSC_FREQ_IN_MHZ
to 400 per Quark datasheet in the Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should allow the value of TSC_FREQ_IN_MHZ to be overridden by
the one in arch/cpu/<xxx>/Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make the Intel quark/galileo support avaiable in Kconfig and Makefile.
With this patch, we can generate u-boot.rom for Intel galileo board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
New board/intel/galileo board directory with minimum codes, plus
board dts, defconfig and configuration files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add minimum codes to support Intel Quark SoC. DRAM initialization
is not ready yet so a hardcoded gd->ram_size is assigned.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC contains an embedded 512KiB SRAM (eSRAM) that is
initialized by hardware. eSRAM is the ideal place to be used
for Cache-As-RAM (CAR) before system memory is available.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move PCI_REG_ADDR and PCI_REG_DATA from arch/x86/lib/pci_type1.c to
arch/x86/include/asm/pci.h, also define PCI_CFG_EN so that these
macros can be used for pci configuration space access.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In the Quark SoC, some chipset commands are accomplished by utilizing
the internal message network within the host bridge (D0:F0). Accesses
to this network are accomplished by populating the message control
register (MCR), Message Control Register eXtension (MCRX) and the
message data register (MDR).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
device.h for integrated pci devices' bdf on Quark SoC and quark.h for
various memory-mapped and i/o-mapped base addresses within SoC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is a relatively low-cost x86 board in a small form factor. The main
peripherals are uSD, USB, HDMI, Ethernet and SATA. It uses an Atom 3800
series CPU. So far only the dual core 2GB variant is supported.
This uses the existing FSP support. Binary blobs are required to make this
board work. The microcode update is included as a patch (all 3000 lines of
it).
Change-Id: I0088c47fe87cf08ae635b343d32c332269062156
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since the FSP is a black box it helps to have some sort of debugging
available to check its inputs. If the debug UART is in use, set it up
after CAR is available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
While queensbay is the first chip with these settings, others will want to
use them too. Make them common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since these board functions seem to be the same for all boards which use
FSP, move them into a common file. We can adjust this later if future FSPs
need more flexibility.
This creates a generic PCI MMC device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This code is ported from the Marvell bin_hdr code into mainline
SPL U-Boot. It needs to be executed very early so that the devices
connected to the serdes PHY are configured correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
This patch adds SPL support to the Marvell Armada-XP. With this addition
the bin_hdr integration is not needed any more. The SPL will first
initialize the serdes/PHY and the call the DDR setup and training code
now integrated into mainline U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
This patch adds SPL support to the db-mv784mp-gp eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
This patch adds SPL support to the maxbcm MV78460 based board. Including
the fixed DDR configuratrion needed for the DDR training code. And the
the serdes PHY init code.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
Checking if the pointer is NULL would be easier to know the tail
of the boot_device_table[] array.
For clarification, add the /* sentinel */ comment.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The return value of get_boot_mode_sel() is used as the index of
the boot_device_table[] array. Its type should be "int" rather
than "u32".
Use only the iterator "i" for the loop in do_pinmon().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
To use I2C controllers on PH1-sLD8, the bit 10 (SCL0/SDA0)
and bit 11 (SCL1/SDA1) of IECTRL register must be set.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
It is true that unused functions are removed from the ELF image
by the compiler's garbage collection but relying on it too much
does not look nice.
Currently, the build is taking more than it should.
Refactor the makefiles to compile only files that are really needed.
CONFIG_SOC_INIT and CONFIG_DRAM_INIT are no longer needed by the
optimization.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since commit 0365ffcc0b (generic-board: show model name in
board_init_f() too), checkboard() is invoked only when
show_board_info() fails to get the model name from Device Tree.
It never happens because UniPhier SoCs now only work with
CONFIG_OF_CONTROL and all the root nodes of UniPhier device trees
have the "model" property.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since commit 0365ffcc0b (generic-board: show model name in
board_init_f() too), the support card information has not been
displayed because check_support_card() is invoked only when
show_board_info() fails to get the model name from Device Tree.
This commit adds misc_init_f() function to call check_support_card()
from there.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now init functions called from board_postclk_init() and dram_init()
are only necessary for SPL.
Move them to spl_board_init() for clean-up.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Currently, I/O pin settings are not necessary for SPL.
The board_early_init_f() seems a suitable place to call pin_init().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The EEPROM chips on UniPhier reference daughter boards expect 2-byte
offset address.
Since 7132b9fd68 (dm: i2c: dts: Support an offset-len device tree
property), I2C sub-nodes can have "u-boot,i2c-offset-len" property.
It is convenient to set the default I2C offset address length in
Device Tree, so that we do not have to set it on the command line.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This EEPROM chip is installed on the expansion board commonly used
on UniPhier platform. To avoid duplicated description, move the
EEPROM node to a separate file and include it from other device tree
sources.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This dummy header was introduced by commit 630bf80ebb (ARM:
UniPhier: add dummy gpio.h to enable CONFIG_OF_CONTROL).
Thanks to commit a08d643dbd (dm: Drop gpio.h header from
fdtdec.c), such an ugly workaround is no longer needed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
For now this code seems to be the same for all FSP platforms. Make it
common until we see what differences are required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
To avoid casts, find_fsp_header() should return a pointer. Add asmlinkage
to two API functions which use that convention. UPD_TERMINATOR is common
so move it into a common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
If the BIOS emulator is not available, allow use of native execution if
available, and vice versa. This can be controlled by the caller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This setting will be used by more than just ivybridge so make it common.
Also rename it to PCIE_ECAM_BASE which is a more descriptive name.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If we don't know the relocation address, the raw values are not very useful.
Show the pre-relocation values as well as these can be looked up in
System.map, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
And use this to set the GMAC Transmit Clock Delay Chain value on Banana
boards, rather then keying of CONFIG_TARGET_FOO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch adds basic constructs in the ARMv8 u-boot code
to handle and apply Cortex-A57 specific erratas.
As and example, the framework showcases how erratas 833069, 826974
and 828024 can be handled and applied.
Later on this framework can be extended to include other
erratas.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
It is painful to specify the full path to the device tree with the -d
option. It is normally kept in the same directory as U-Boot, so provide
an option to use this by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Juno Development Platform is a physical Versatile Express
device with some differences from the emulated semihosting
models. The main difference is that the system is split in
a SoC and an FPGA where the SoC hosts the serial ports at
totally different adresses.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Versatile Express ARMv8 semihosted FVP platform is still
using the legacy CONFIG_SYS_EXTRA_OPTIONS method to configure
some compile-time flags. Get rid of this and create a Kconfig
entry for the FVP model, and a selectable bool for the
semihosting library.
The FVP subboard is now modeled as a target choice so we can
eventually choose between different ARMv8 versatile express
boards (FVP, base model, Juno...) this way. All dependent
symbols are updated to reflect this.
The 64bit Versatile Express board symbols are renamed
VEXPRESS64 so we have some chance to see what is actually
going on. Tested on the FVP fast model.
Acked-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unify and move code in arch/mips/cpu/mips[32|64]/ to arch/mips/cpu/.
The CPU specific config.mk files need to remain until
CONFIG_STANDALONE_LOAD_ADDR is converted to a global Kconfig symbol.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Move all au1x00 code out of arch/mips/cpu/mips32 to allow
unification of CPU code in a later patch. The reorganization
of the SoC specific header files will be done in a later patch
series.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
In preparation for sharing a single copy of start.S between mips32 &
mips64, handle setting the KX bit of the cop0 Status register when the
mips32 start.S is built for mips64.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
In preparation for sharing a single copy of start.S between mips32 &
mips64, handle mips64 relocations in the mips32 start.S when built for
mips64.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Where the mips32 & mips64 implementations of start.S differ in terms of
access sizes & offsets, use the appropriate macros from asm.h to
abstract those differences away. This is in preparation for sharing a
single copy of start.S between mips32 & mips64.
The exception to this is loads of immediates to be written to the cop0
Config register, which is a 32bit register on mips64 and therefore
constants written to it can be loaded as such.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This change fixes i2c bus numbering for Odroid U3.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Some versions of Exynos5 supports High-Speed I2C,
on few interfaces, this change allows support this.
The new flag is: PINMUX_FLAG_HS_MODE
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Without this alias setting, the seq numbers
of the i2c devices are wrong.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
This patch modify i2c nodes in exynos4.dtsi with:
- adding proper interrupts arrays for each i2c node,
which allows to decode periph id
- add reg address for each i2c node for i2c driver internal use
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
this is an atempt to make the export of functions typesafe.
I replaced the jumptable void ** by a struct (jt_funcs) with function pointers.
The EXPORT_FUNC macro now has 3 fixed parameters and one
variadic parameter
The first is the name of the exported function,
the rest of the parameters are used to format a functionpointer
in the jumptable,
the EXPORT_FUNC macros are expanded three times,
1. to declare the members of the struct
2. to initialize the structmember pointers
3. to call the functions in stubs.c
Signed-off-by: Martin Dorwig <dorwig@tetronik.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(resending to the list since my tweaks are not quite trivial)
Rather than assuming that the chip offset length is 1, allow it to be
provided. This allows chips that don't use the default offset length to
be used (at present they are only supported by the command line 'i2c'
command which sets the offset length explicitly).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
U-Boot now supports using GPIOs using bank phandles instead of global
numbers. Update the exynos device tree files to use this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Add a new 'demo light' command which uses GPIOs to control imaginary lights.
Each light is assigned a bit number in the overall value. This provides an
example driver for using the new GPIO API.
Signed-off-by: Simon Glass <sjg@chromium.org>
In f0c3a6c we stopped setting gd in board_init_f, but later had to
revert to due problems on certain platforms. As davinci does not look
to have these problems, we can drop the setting here and rely upon
crt0.S to do it.
Cc: Peter Howard <pjh@northern-ridge.com.au>
Signed-off-by: Tom Rini <trini@ti.com>
On the DRA72x (J6Eco) EVM one PMIC SMPS is powering three SoC
core rails. This concept of using one SMPS to supply multiple
core domains (in various, although limited combinations, per
primary device use case) has now become common and is used by
many customer J6/J6Eco designs; it is supported by a number of
corresponding PMIC OTP versions.
This patch implements correct operation of the core voltages
scaling routine by ensuring that each SMPS that is supplying
more than one domain shall be written only once, and with the
highest voltage of those fused in the SoC (or of those defined
in the corresponding header if fuse read is disabled or fails)
for the power rails belonging to the group.
The patch also replaces some PMIC-related magic numbers with
the appropriate definitions. The default OPP_NOM voltages for
the DRA7xx SoCs are updated as well, per the latest DMs.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
This patch adds IDE support to the MIPS Malta board. The IDE controller
is enabled after probing the PCI bus and otherwise just makes use of
U-boot generic IDE support.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Current MIPS cores from Imagination Technologies use TagLo select 2 for
the data cache. The architecture requires that it is safe for software
to write to this register even if it isn't present, so take the trivial
option of clearing both selects 0 & 2.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Current MIPS systems do not require that loads be performed to force the
parity of cache lines, a simple invalidate by clearing the tag for each
line will suffice. Thus this patch makes the loads & subsequent second
invalidation conditional upon the CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD
option, and defines that for existing mips32 targets. Exceptions are
malta where this is known to be unnecessary, and qemu-mips where caches
are not implemented.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
