Update this code to use write_pix8() rather than writing the pixels only
for a single supported display depth. This allows us to support any
depth.
Add some more tests too.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the code that writes to a pixel is quite convoluted. It uses a
colour map which is in the uclass and the same code is repeated in
different places within video_bmp_display().
As a first step, create a function which can write a pixel from the
bitmap, no matter what the display depth. Use any provided palette
directly, rather than using the uclass version.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a few more tests for BMP rendering. Use a back door into the sandbox
SDL driver to adjust the resolution at runtime.
The truetype code does not support 8bpp. Add this so that the display is
not blank when running in this mode.
Signed-off-by: Simon Glass <sjg@chromium.org>
The intention is for the copy base to start halfway through the
frame-buffer area. At present is it actually below the frame buffer,
which could have anything in it (probably it is malloc space). Fix
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
If U-Boot starts with the frame buffer set to 16bpp but then runs a test
that uses 32bpp, there is not enough space. Update the driver to use the
maximum possible frame-buffer size, to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When unit tests are run they currently create a new window. Update the
code so that the old one is removed first. This avoids the confusion as to
which one is active.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox only supports 16 and 32bpp depths, since those are the
easy ones with SDL.
We can support other depths by manually converting the pixel formats. Add
support for this, to enable an 8ppp (monochrome) format.
Signed-off-by: Simon Glass <sjg@chromium.org>
The watchdog system reset driver can reboot the device but it cannot power
it off. If power off is requested, the driver should not reset the system
but leave powering off to one of the other system reset drivers.
As power cycling is typically not a feature of a watchdog driver the reset
types SYSRESET_POWER and SYSRESET_POWER_OFF shall both be excluded.
Fixes: 17a0c14164 ("dm: sysreset: add watchdog-reboot driver")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The global data pointer is not used in this driver, remove it's
declaration.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Use more appropriate resource_size() function when working with data in
struct resource.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Function mvebu_pcie_setup_wins() sets up all other BARs, so move setup of
BAR[0] to this function to have common code at one place.
In the past, commit 193a1e9f19 ("pci: pci_mvebu: set BAR0 after memory
space is set") moved setup of BAR[0] to another location, due to ath10k
not working in kernel, but the reason why was unknown, but it seems to
work now, and we think the issue then was cause by the PCIe Root Port
presenting itself as a Memory Controller and therefore U-Boot's code
have overwritten the BAR. Since the driver now ignores any write
operations to PCIe Root Port BARs, this should not be an issue anymore.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Testing on Armada XP with an EEPROM using register address with size
of 2 has shown, that the register address bytes are sent to the I2C
EEPROM in the incorrect order. This patch swabs the address bytes so
that the correct address is transferred to the I2C device.
BTW: This worked without any issues before migrating Armada XP to
DM I2C.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pali Rohár <pali@kernel.org>
Cc: Marek Behún <marek.behun@nic.cz>
Tested-by: Marek Behún <marek.behun@nic.cz>
There is no maintainer entry for serial_mvebu_a3700.c. Add entry with Pali
and Stefan as maintainers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no maintainer entry for pci-aardvark.c. Add entry for
pci-aardvark.c and pci_mvebu.c with Pali and Stefan as maintainers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Convert A3720 common PHY driver to official DT bindings.
This puts us closer to be able to synchronize A3720 device-trees with
those from Linux.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace fdt_alloc_phandle() with subsequent fdt_set_phandle() by
fdt_create_phandle().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
No functional change intended. This patch switches from the legacy I2C
API to the DM I2C API, so that this code can be used with DM I2C
enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
This function will be commonly used in block device drivers
in the succeeding patches.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmG8PNIcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyN4NCACbdi5EFjoNkGhCWLIX
SobXNcBGaL9Zpr5qZq77uFqFeFPeiAClk9X+TcSHhBTSWPugzNCdXEdENEGdiiOR
Yxe/QvBL7ZsKkhGBw5W8sb81NBPlpnVY7DWufjYvWq7S3C3bIDahQpCeWHKXDO0H
ZzIX1413kfHRKsAIT+IbufmC1dcWY8SWQEArSkL2KhTQyHnLVGAaholgEGXoKMoC
0ACXO+uhqaAY0/1eWvvYjcfotlz881ROajSRITh+Gu0UuHyRr2Fvj7jZvF5E4Q4f
Cu8iciDsimYSDGLZsOJjPIDTfsx9jbA8IcYIAMxOLW8OYbIL6QAUKsJ2LLKao1q5
SYXP
=YXsB
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.04 cycle:
This feature set includes : support for the new QSPI hardware on
sama7g5, small fixes on sam9x60 and sama7g5, some additions of commands
and PIO controller on sam9x60/sam9x60ek.
Double peripheral RBF configuration are needed on some devices or boards
to stabilize the IO configuration system.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Sin Hui Kho <sin.hui.kho@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
This adds better logging support for many CCF drivers, and clarifies some
documentation regarding clk_get_rate.
-----BEGIN PGP SIGNATURE-----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=1L3q
-----END PGP SIGNATURE-----
Merge tag 'clk-2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-clk
Clock patches for v2022.01-rc3
This adds better logging support for many CCF drivers, and clarifies some
documentation regarding clk_get_rate.
Define LOG_CATEGORY to allow filtering with log command
for generic clock and CCF clocks.
This patch also change existing printf, debug and pr_ macro
to log_ or dev_ macro.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reorder include files in the U-Boot expected order:
the common.h header should always be first,
followed by other headers in order,
then headers with directories,
then local files.
It is a preliminary step for next patch.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
PCI Bridge which represents aardvark PCIe Root Port has Expansion ROM Base
Address register at offset 0x30 but its meaning is different than PCI's
Expansion ROM BAR register. Only address format of register is same.
In reality, this device does not have any configurable PCI BARs. So ensure
that write operation into BARs (including Expansion ROM BAR) is noop and
registers always contain zero address which indicates that bars are
unsupported.
Fixes: cb056005dc ("arm: a37xx: pci: Add support for accessing PCI Bridge on root bus")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The PCI Bridge which represents mvebu PCIe Root Port has Expansion ROM
Base Address register at offset 0x30 but its meaning is different that
of PCI's Expansion ROM BAR register, although the address format of
the register is the same.
In reality, this device does not have any configurable PCI BARs. So
ensure that write operation into BARs (including Expansion ROM BAR) is a
noop and registers always contain zero address which indicates that BARs
are unsupported.
Fixes: a7b61ab58d ("pci: pci_mvebu: Properly configure and use PCI Bridge (PCIe Root Port)")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Since u32 takes up 4 bytes, we need to divide the number of u32s by 4
for cfgcache.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The RZ/G2 series uses an external clock as a reference to the AVB.
If this clock is controlled by an external programmable clock,
it must be requested by the consumer or it will not turn on.
In order to do this, update the driver to use bulk enable and
disable functions to enable clocks for boards with multiple clocks.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add a block driver which handles read/write for EFI block devices. This
driver actually already exists ('efi_block') but is not really suitable
for use as a real U-Boot driver:
- The operations do not provide a udevice
- The code is designed for running as part of EFI loader, so uses
EFI_PRINT() and EFI_CALL().
- The bind method probes the device, which is not permitted
- It uses 'EFI' as its parent device
The new driver is more 'normal', just requiring its platform data be set
up in advance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
UCLASS_EFI_LOADER is used for devices created by applications and
drivers loaded by U-Boots UEFI implementation.
This patch provides a new uclass (UCLASS_EFI_MEDIA) to be used for devices
that provided by a UEFI firmware calling U-Boot as an EFI application.
If the two uclasses can be unified, is left to future redesign.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
These names are better used for access to devices provided by an EFI
layer. Use EFI_LOADER instead here, since these are only available in
U-Boot's EFI_LOADER layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
sama7g5 QSPI has:
1/ One Octal Serial Peripheral Interfaces (QSPI0) Supporting Up to
200 MHz DDR. Octal, TwinQuad, Hyperflash and OctaFlash Protocols Supported
2/ One Quad Serial Peripheral Interfaces (QSPI1) Supporting Up to
90 MHz DDR/133 MHz SDR
The QSPI controller of SAMA7G5 uses different clock domains, hence extra
synchronization operations must be performed before accessing some
registers. Differentiate between the versions of the IP using has_gclk.
Differentiate between QSPI0 and QSPI1 with has_octal.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This is not needed anymore. Drop it to simplify the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CONFIG_SYS_ATA_PORT_ADDR is not used in the code anymore. Drop it and use
ATA_PORT_ADDR() locally instead.
Drop CONFIG_IDE_RESET_ROUTINE and CONFIG_IDE_SWAP_IO which are also
unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
This can go in the related header file. Drop the CONFIG option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* fixes the bug in function bind_drivers_pass that for
CONFIG_CC_OPTIMIZE_FOR_SIZE=n and no entries in the driver_info list,
i.e. n_ents == 0, the processor steps into the first loop iteration
despite the loop condition being false.
* the Xilinx Zynq-7000 device would eventually hang due to an attempted
access to an invalid memory address
* the bug is fixed by changing the type of idx from uint to int
Board: zynq-zybo
Target: ARM
Compiler: arm-none-eabi-gcc 9.2.1
Signed-off-by: Alexander Preissner <fpga-garage@preissner-muc.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Add I2C driver code for the Microchip PolarFire SoC.
This driver supports I2C data transfer and probe for I2C
slave addresses.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Remove the microchip compatible string and default compatible "cdns,macb"
support both 32-bit and 64-bit DMA access.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enable DWC IP clock in driver probe, so the MII access is possible even
outside of active network transfers. This is particularly useful when
using 'mii' or 'mdio' commands to explore PHY state, neither of which
works with DWMAC currently due to the disabled clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The gpio_request_by_name() returns zero in case of success, however the
conditional return value check in gpio_request_by_name() checks only for
(ret != -ENOENT) and if the condition is true, returns ret outright.
This leads to a situation where successful gpio_request_by_name() return
leads to immediate successful eth_phy_of_to_plat() return as well, and
to skipped parsing of "reset-assert-us" and "reset-deassert-us", so the
PHY driver operates with valid reset GPIO, but with assert/deassert times
set to default, which is 0, instead of the values from DT. This breaks
PHY reset.
Fix this by checking if return value is non-zero and then for this one
single allowed non-zero return value, -ENOENT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Broadcom bnxt L2 driver support. Used by the Broadcom
iproc platforms.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
It turns out that in custom designs if the system is reset
multiple times in conjunction with a slight increase in external
temperature, the felix switch starts to behave in a strange way:
packets are no longer received on the ENECT interface connected
to the L2switch internal port (the TX side of internal port stops working
or the packets do not reach there. It is not very clear where
the packets remain blocked. None of the counters points to a disruption
in the L2switch)
The issue is not reproducible on NXP reference designs.
It was observed that by adding the switch core reset, the problem
goes aways, even if intensive testing in temperature chambers
is applied.
The current patch performs soft reset on the switch core to ensure proper
operation of the L2switch.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This symbol is not used anywhere in the code. Just enable in couple of
defconfigs but it does nothing that's why remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Wait for the read/write transfer finish bit get actually cleared,
this does not happen immediately on at least SoCFPGA Gen5.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Add a message on probe in driver model core when the default
pinctrl selection failed.
This message is displayed only when the pinctrl API is
implemented, i.e. when result is not ENOSYS.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM
This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the commit f42045b2e7 ("stm32mp15: replace CONFIG_TFABOOT when
it is possible") the function stm32mp1_ddr_setup is always called so the
__maybe_unused can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Compute the DDR size from DDR controller register (mstr and addrmap)
in U-Boot proper as the DDR information are useful only for SPL
but not for U-Boot proper, for example with TFABOOT.
This patch simplify U-Boot DT when several DDR size are supported
and support of next SOC in STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Align the framebuffer size on MMU_SECTION_SIZE in kernel, = max 2MB for
LPAE for armV7, to avoid issue with the simple frame buffer activation,
when U-Boot add a reserved memory in the kernel device tree to preserve
the splash screen until Linux driver initialization.
See Linux documentation for details:
Documentation/devicetree/bindings/display/simple-framebuffer.yaml
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the helper function video_is_active() to test if one video device
is active.
This function can be used in board code to execute operation
only when the display is probed / really used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove the DDR interactive command tuning, as the support of a predefined
DDR PHY tuning is removed for STM32MP1 driver in SPL and in TF-A
and the result of this tuning will be never used.
Moreover this SW tuning procedure can failed on some hardware
configuration (to many BIST errors and no convergence); it will be no
more supported in the next delivery of the DDR utilities included in
the CubeMX tool of STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The support of a predefined DDR PHY tuning result is removed for
STM32MP1 driver because it is not needed at the supported frequency
when built-in calibration is executed.
The calibration parameters were provided in the device tree by the
optional node "st,phy-cal", activated in ddr helper file by the
compilation flag DDR_PHY_CAL_SKIP and filled with values generated
by the CubeMX DDR utilities.
This patch
- updates the binding file to remove "st,phy-cal" support
- updates the device trees and remove the associated defines
- simplifies the STM32MP1 DDR driver and remove the support of
the optional parameter "st,phy-cal"
After this patch, the built-in calibration is always executed
and the calibration registers are moved in the phy dynamic part;
that allows manual tests.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the read data eye training = training for optimal read valid placement
(RVTRN) when the built-in calibration is executed for LPDDR2 and LPDDR3.
This training is supported on the PUBL integrated in the STM32MP15x
DDR subsystem and it is not required for DDR3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for testing whether bus voltage level translator is present
and operational. This is useful on systems where the bus voltage level
translator is optional, as the translator can be auto-detected by the
driver and the feedback clock functionality can be disabled if it is
not present.
The translator test sets CMD high to avoid interfering with a card, and
then verifies whether signal set on CK is detected on CKIN. If the signal
is detected, translator is present, otherwise the CKIN feedback clock are
disabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Yann Gautier <yann.gautier@foss.st.com>
tpm_tis_remove() leads to calling tpm_tis_ready() with the IO region
unmapped and chip->locality == -1 (locality released). This leads to a
crash in mmio_write_bytes().
The patch implements these changes:
tpm_tis_remove(): Unmap the IO region after calling tpm_tis_cleanup().
tpm_tis_cleanup(): Request locality before IO output and releasing
locality.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Sometimes UART stops transmitting characters after UART clock is changed
back to XTAL. In this state UART fifo is always full. Kernel during early
boot wants to print output on UART and is waiting for non-empty UART fifo.
Which leads to CPU hangup without any (debug) output on UART.
Marvell Armada 3700 Functional Specifications says that for programming
fractional divisor registers it is required to disable UART, enable
loopback mode, reset fifos, program registers, disable loopback mode,
release reset of fifos and enable UART.
But these steps do not fix above mentioned issue that UART hangup. Also
gating UART clock does not help. And even resetting UART state machines do
not help.
Experiments showed that UART fifo is unblocked after board is being reset
(during board reset UART HW transmit UART fifo even CPU is not executing
kernel/bootloader anymore).
And another experiments showed that same workaround can be achieved also
by external reset of UART HW (without need to reset board).
So do not implement any of "Marvell recommended" steps from Functional
Specifications as they do not work. And rather prior changing parent clock
back to XTAL, do external reset of UART HW. This operation also resets all
UART registers, so basically it also sets UART clock to default, which is
XTAL. It is unknown why UART hangups and enters such broken state.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add a function that returns the number of devices in a uclass. This can be
helpful in sizing an array that needs to hold a list of them.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it is useful to search just by a partial name, such as
when looking for a sibling device that has a common name substring. Add
helper functions to handle these requirements.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support reading a string list a string at a time. Apart
from being inefficient, this makes it impossible to separate reading of
the devicetree into the of_to_plat() method where it belongs, since any
code which needs access to the string must read it from the devicetree.
Add a function which returns the string property as an array of pointers
to the strings, which is easily used by clients.
Signed-off-by: Simon Glass <sjg@chromium.org>
The details for of_property_read_string_helper() and
ofnode_read_string_index() are a little inaccurate. Fix up the comments to
avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
This method is currently called after the platform data has been freed.
But the pre_unbind() method may wish to access this, e.g. to free some
data structures stored there.
Split the unbinding of devices into two pieces, as is done with removal.
This corrects the problem.
Also tidy a code-style issue in device_remove() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the MMC uclass assumes that the only child it can have is a
block device. Update this so we can add a bootmethod too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way for sandbox MMC to present data from a backing file. This
allows a filesystem to be created on the host and easily served via an
emulated mmc device.
Signed-off-by: Simon Glass <sjg@chromium.org>
This change implements an SCMI transport for agent interfacing the
OP-TEE SCMI service. OP-TEE provides an SCMI PTA (Pseudo-TA) for
non-secure world to send SCMI messages over an identified channel.
The driver implemented here uses a SMT shared memory for passing
messages between client and server.
The implementation opens and releases channel resources for each
passed SCMI message so that resources allocated (sessions) or
registered (shared memory areas) in OP-TEE firmware are released for
example before relocation as the driver will likely allocate/register
them back when probed after relocation.
The integration of the driver using dedicated config switch
CONFIG_SCMI_AGENT_OPTEE is designed on the model posted to the
U-Boot ML by Patrick Delaunay [1].
Link: [1] https://lore.kernel.org/all/20211028191222.v3.4.Ib2e58ee67f4d023823d8b5404332dc4d7e847277@changeid/
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove unused OPTEE_MSG_LOGIN_* ID macros as suitable TEE_LOGIN_* ID
macros are already defined tee.h.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Change SCMI smccc transport drivers to use platform data rather
than private data for channel reference since it only stores platform
data retrieved from the DT. Consequently the probe handler is replaced
with a of_to_plat handler.
Cc: Simon Glass <sjg@chromium.org>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change SCMI mailbox transport drivers to use platform data rather
than private data for channel reference since it only stores platform
data retrieved from the DT. Consequently the probe handler is replaced
with a of_to_plat handler.
Cc: Simon Glass <sjg@chromium.org>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Correct scmi mailbox probe function that can't free the scmi channel
instance since its auto-allocated by the device model framework.
Cc: Simon Glass <sjg@chromium.org>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add two configs CONFIG_SCMI_AGENT_MAILBOX and CONFIG_SCMI_AGENT_SMCCC
to select the supported agents as all the agents are not supported.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Some boards need to change the tx/rx delay config in order for
gigabit Ethernet to work.
In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), Realtek documented the bits for overriding the delays
from the hardware straps.
Copy the logic from linux, so the delay config is set from the PHY's
interface type (the phy-mode property in the device tree).
This removes the need for a one-off workaround for the Pine A64+ board.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a driver for the MDIO interface for Aspeed AST2600 SOC. The driver
only supports clause 22 for now.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
redundant_init() is only called in the tsec driver. Make it static.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
priv->promisc is used as the parameter of the set_promisc() call
which accepts a bool type instead of char.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If using OF_CONTROL, fdtcontroladdr is set to the fdt used to configure
U-Boot. When using PXE, if no fdt is defined in the menu file, and
there is no fdt at fdt_addr, add fall back on fdtcontroladdr too.
We are developing board support for the Armv8r64 FVP using
config_distro_bootcmd. We are also using OF_BOARD and would like the
PXE boot option to default to the fdt provided by board_fdt_blob_setup.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
The list of ports which support SGMII depending on switch generation is
available here:
https://www.kernel.org/doc/html/latest/networking/dsa/sja1105.html#port-compatibility-matrix
SGMII can either be used to connect to an external PHY or to the host
port. In the first case, the use of in-band autoneg is expected, in the
last, in-band autoneg is expected to be turned off (fixed-link). So the
driver supports both cases.
SGMII support means configuring the PCS and PMA. The PCS is a Synopsys
Designware XPCS, in Linux this has a separate driver but here it is
embedded within the sja1105 driver. If needed it can be taken out later,
although we would need a UCLASS_PCS for it, which we don't have atm.
Nonetheless, I did go all the way to export an internal MDIO bus for PCS
access, because it is nice to be able to debug the PCS through commands
such as:
=> mdio read ethernet-switch@1-pcs 4 1f.0
Reading from bus ethernet-switch@1-pcs
PHY at address 4:
31.0 - 0x1140
The internal MDIO bus is not registered with DM because there is no
udevice on it, as mentioned. But the XPCS code can still be ripped out,
as needed.
I did not add support for 2500base-x because I do not expect this
interface type to be used as a boot source for anybody, it would just
add unnecessary bloat.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The SJA1105 driver is largely reused from Linux. Its programming model
is that it is blank out of reset, and it waits for a static
configuration stream over SPI, which contains all runtime parameters (it
has no notion of "default values").
Keeping a binary array for the configuration stream would have meant
that aspects such as the CPU port and the MAC speeds could have not been
configured easily, and would have been static and board-dependent.
Live-patching the binary array means recalculating the static config
table CRCs, which is not a fun process.
So we create an abstraction over the static config tables, using the
packing API, same as in Linux. The tables are kept as C structures, and
the binary configuration stream is constructed on-the-go, with CRC and
all.
All static config tables instantiated in this driver are mandatory.
The hardware reference manual can be found at:
https://www.nxp.com/docs/en/user-guide/UM10944.pdf
For tagging, a simplified version of tag_8021q from Linux is used. The
VLAN EtherType is the same (0xdadb) but since we don't want switching in
U-Boot, there is no reason to have a TX VLAN and an RX VLAN for each
port. We just need the RX VLANs to act as the unique pvid of each
front-panel port, to decode the switch port number. The RX VLAN is used
for both RX and TX.
The device tree bindings are the same as in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Instead of trying to guess which operating modes need in-band
negotiation to be active and which ones don't, parse the available
information from the device tree. That will be correct in the cases we
can already guess, and more.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Certain serial SERDES protocols like 1000base-x, 2500base-x, SGMII,
USXGMII can operate either in a mode where the PHY (be it on-board or
inside an SFP module) passes the link parameters (speed, duplex, pause)
to the MAC through in-band through control words standardized by IEEE
802.3 clause 37, or in a mode where the MAC must configure (force) its
link parameters based on information obtained out-of-band (MDIO reads,
guesswork etc).
In Linux, the OF node property named "managed" is parsed by the phylink
framework, and the convention is that if a driver uses phylink, then the
presence of this property means that in-band autoneg should be enabled,
otherwise it shouldn't.
To be compatible with the OF node bindings of drivers that use phylink
in Linux, introduce parsing support for this property in U-Boot too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The Freescale TSEC can be a DSA master, and the ports of the attached
DSA switch can have different MAC addresses compared to the TSEC.
Nonetheless, the TSEC must receive the packets on behalf of those switch
ports. Therefore, implement the promiscuous mode method to allow DSA to
set this.
Note that the init_registers() function called from eth_ops :: start
overwrites this setting. There is no reason why the RCTRL register
should be zero-initialized, so just stop clearing it so that the setting
we applied in eth_ops :: set_promisc sticks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The VSC8502 is a Microchip (formerly Microsemi, formerly Vitesse)
dual port, gigabit Ethernet copper PHY which supports the MII, GMII and
RGMII MAC-side interfaces.
Of these, I could only test RGMII, and my board needed RGMII delays to
be applied by software, so I am able to confirm that this patch handles
that properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
It was wrongly set to "MR", fix it.
Fixes: 52e2565bfb ("spi: atmel-quadspi: Add verbose debug facilities to monitor register accesses")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
- meson64_android: handle errors on boot and run fastboot on boot failure
-----BEGIN PGP SIGNATURE-----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=i2VH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20211119' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- pinctrl: Correct the driver GPIO declaration
- meson64_android: handle errors on boot and run fastboot on boot failure
This should use the provided U_BOOT_DRIVER() macro so that the driver gets
added to the appropriate linker list. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 7c9dcfed50 ("pinctrl: meson: rework gx pmx function")
Reported-by: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com> on libretech-cc
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Consulting to "NVM Express® Base Specification, revision 2.0".
If more PRP List pages are required, then the last entry of
the PRP List contains the Page Base Address of the next PRP
List page. The next PRP List page shall be memory page aligned.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Most NVME devcies maintain data in internal cache for an uncertain
times, and u-boot has no method to force NVME to flush cache.
So this patch adds FUA to avoid data loss caused by power off after data
programming.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
When booting U-Boot in crosvm, the virtual machine emulates a PCI cam
device, not the PCI-E 'ecam' device normally seen on e.g. QEMU. This
PCI device can be supported with only trivial changes to the ecam
driver.
Instead of adding a completely new driver which is identical besides the
initialization step, add support for the PCI version to the existing
driver.
Signed-off-by: Alistair Delva <adelva@google.com>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: Ram Muthiah <rammuthiah@google.com>
Hash and Crypto Engine (HACE) is designed to accelerate the
throughput of hash data digest, and symmetric-key encryption.
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add YCLK enable for HACE, the HW hash engine of
ASPEED AST2600 SoCs.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
With the recent changes on mmc driver, we saw that the boot is ~5 secs
longer compared to v2021.07 on mediatek platforms.
This regression is seen during mmc_init and caused by the following
patch [1].
Indeed since we did not support poll dat0, we fulfilled the condition
of [1] and a delay of 500 ms was added for every __mmc_switch call.
By adding the support of wait_dat0(), we now don't need to mdelay
during mmc_init anymore.
[1]: https://patchwork.ozlabs.org/project/uboot/patch/1629192034-64056-1-git-send-email-ye.li@nxp.com/
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Lot of PCIe controllers are using ECAM addressing. So add common ECAM
macros into U-Boot's pci.h header file which can be suitable for most
PCI controller drivers.
Replace custom ECAM address macros in every PCI controller driver by new
ECAM macros from U-Boot's pci.h header file.
Similar macros are defined also in Linux kernel. There is a small
difference between Linux and these new U-Boot macros.
U-Boot's PCIE_ECAM_OFFSET() takes device and function numbers in separate
arguments. Linux's PCIE_ECAM_OFFSET() takes device and function numbers
encoded in one argument. The reason is that U-Boot's PCI_DEVFN() macro is
different than Linux's PCI_SLOT() macro. So having device and function
numbers in separate arguments makes code more straightforward.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This driver supports both pin muxing and GPIO support for the
pin control logic found on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
This driver uses Pinctrl framework and is compatible with the Linux
driver for AST2600.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
%d was being used as the specifier for size_t, leading to a
compiler warning
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Without get_desc, the tpm command will not provide a
description of the device in 'tpm device' or 'tpm info'.
Due to the characteristics of the Atmel TPM it isn't
possible to determine certain attributes (e.g open/close
status) without using the TPM stack (compare Infineon
and ST TPM drivers), so just print out the chip model
and udevice name as the identifier.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This driver was broken due to an empty offset byte being prepended
at the start of every transmission.
The hardware does not mimic an EEPROM device with registers so
an offset byte is not required.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
There are no users of this driver without DM_I2C
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYZPDrwAKCRDKSWXLKUoM
IS9GAJ93T/uprhLcKWMb+284YMb2caWgOACfZ02nTlzvZKNNXVretJgZaHXqj1M=
=cwTL
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
This ensures the USB_MUSB_PIO_ONLY config is set to an apppropriate
value from the changes enabling USB_MUSB_GADGET does.
Namely, USB_MUSB_PIO_ONLY default to =y on USB_MUSB_SUNXI being y.
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
With CONFIG_SYSRESET_WATCHDOG=y the sandbox can use a watchdog based system
reset.
To make this work calling sandbox_wdt_expire_now() must lead to a reset.
With this change we can test the development suggested in
[PATCH 0/4] Improved sysreset/watchdog uclass integration
https://lists.denx.de/pipermail/u-boot/2021-August/458656.html
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver supports the ds1339 as well, which was probably intended by
the author but prevented by a typo. Fix the typo.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
Convert our SPI TPM driver and use the newly added API
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add support for devices that expose a TPMv2 though MMIO.
Apart from those devices, we can use the driver in our QEMU setups and
test TPM related code which is difficult to achieve using the sandbox
driver (e.g test the EFI TCG2 protocol).
It's worth noting that a previous patch added TPMv2 TIS core functions,
which the current driver is consuming.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
There's a lot of code duplication in U-Boot right now. All the TPM TIS
compatible drivers we have at the moment have their own copy of a TIS
implementation.
So let's create a common layer which implements the core TIS functions.
Any driver added from now own, which is compatible with the TIS spec, will
only have to provide the underlying bus communication mechanisms.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
With the upcoming TPM2 API, some of the functions name are part of the new
header file. So switch conflicting internal function names and defines.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
With the upcoming TPM2 API, some of the functions name are part of the new
header file. So switch conflicting internal function names and defines.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
In some part of STM32MP15 support the CONFIG_TFABOOT can be replaced
by other config: CONFIG_ARMV7_PSCI and CONFIG_ARM_SMCCC.
This patch also simplifies the code in cpu.c, stm32mp1_ram.c and
clk_stml32mp1.c as execution of U-Boot in sysram (boot without SPL and
without TFA) is not supported: the associated initialization code is
present only in SPL.
This cleanup patch is a preliminary step to support SPL load of OP-TEE
in secure world, with SPL in secure world and U-Boot in no-secure world.
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The stm32 gpio driver private data are not needed in arch include files,
they are not used by code except for stm32 gpio and pincontrol drivers,
using the same IP; the defines for this IP is moved in a new file
"stm32_gpio_priv.h" in driver/gpio.
This patch avoids to have duplicated file gpio.h for each SOC
in MPU directory mach-stm32mp and in each MCU directory arch-stm32*
and allows to remove CONFIG_GPIO_EXTRA_HEADER for all STM32.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Header file mach/cpu.h already defines MBUS_PCI_MEM_SIZE macro which
defines size of MBUS_PCI_MEM_BASE window. So use global MBUS_PCI_MEM_SIZE
macro instead of locally defined PCIE_MEM_SIZE macro. Both macros have same
definition.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The Sunxi boards only support a 16 second watchdog timeout. This is too
short to boot Linux. The UEFI specification requires 300 seconds as
default timeout.
Change the default for CONFIG_WATCHDOG_AUTOSTART for ARCH_SUNXI.
Fixes: b147bd3607 ("sunxi: Enable watchdog timer support by default")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In the current code, it doesn't reset the cursors of LUT entry and
StreamID at the beginning of the fixup, so it can result in LUT entry
setup and msi-map mismatch and LUT entries and StreamID leaking
when reload and fixup the DTB.
This patch move the initialization of LUT entry and StreamID cursors
to the beginning of the fixup to resolve the issues.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for the proper dwc3 device tree binding support as specified
in the offical device tree spec.
Initially, add support for the LS1028A support. Other SoCs should be
easy to add by just adding the corresponding compatible string.
Unfortunately, the device trees of all other layerscape SoCs are not
converted and uses a wrong compatible string only known in u-boot.
To maintain backwards compatibility with current u-boot device trees,
add the generic "fsl,layerscape-dwc3" compatible string.
OTG mode is not supported yet. The dr_mode in the devicetree will either
have to be set to peripheral or host.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
[backport from linux commit d9612c2f0449e24983a8b689603210486a930c90]
Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
[backport from linux commit db2be4e9e30c6e43e48c5749d3fc74cee0a6bbb3]
Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Both dr_mode and maximum-speed properties are usually optional. Drivers
will still try to fetch the properties nonetheless, which leads to error
messages, although they are no errors. Change pr_err() to pr_debug().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official bindind of the PCIe controller of the ls1028a has the
following compatible string:
compatible = "fsl,ls1028a-pcie";
Additionally, the resource names and count are different. Update the
driver to support this binding and change the entry in the ls1028a
device tree.
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-dwc3", "snps,dwc3";
Change the ls1028a device tree and add this new compatible to the fsl
specific xhci driver, otherwise the generic dwc3 driver will be used
with the compatibles above.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The driver will look for a named resource "ecc-addr", but this isn't the
official binding. In fact, the official device tree binding
documentation doesn't mention any resource names at all. But it is safe
to assume that it's the linux ones we have to use if we want to be
compatible with the linux device tree. Thus rename "ecc-addr" to
"sata-ecc" and convert all the users in u-boot.
While at it, also rename "sata-base" to "ahci" although its not used at
all.
This change doesn't affect the SATA controller on the ZynqMP.
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-lpuart";
Add the missing compatible to the driver and update the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official devicetree bindings specifies spi-num-chipselects as the
name. Use it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";
Add the missing compatible to the driver and update the device tree.
We can use the fallback "fsl,ls1021a-v1.0-dspi", because the endianness
is determined by the little-endian property and not by the compatible
string itself. Further, we won't need and specific details on the DMA
configuration (which is different on the LS1021A). If it's ever needed,
we can later add the more specific "fsl,ls1028a-dspi" compatible to the
driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to the linux device tree specification the compatible string
is:
compatible = "arm,sp805", "arm,primecell";
Fix all users in u-boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Adds check for memory clock variable before calculating caslat_actual.
Set mclk_ps to slowest DIMM supported if mclk_ps is found zero.
Signed-off-by: Maninder Singh <maninder.singh_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix Bad Shift operator issue in step_to_string function
by adding an if check
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix possible divide by zero issue in fsl_ddr_set_memctl_regs
by adding an if check
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix possible divide by zero issue in get_memory_clk_period_ps
by adding a check
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
to fix following checkpatch warings.
WARNING: struct should normally be const
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
At present the counter never hits the comparitor in this case. Add a
special case.
This ensures that the snow backlight works when at full brightness.
Fixes: 76c2ff3e5f video: backlight: fix pwm's duty cycle calculation
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently output of dfu commands ends on a line with leading hash signs
('#'). The succeeding output should be placed on a new line.
After writing updates via dfu print a new line.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add an option to automatically register watchdog devices with the
wdt_reboot driver for use with sysreset. This allows sysreset to be a
drop-in replacement for platform-specific watchdog reset code, without
needing any device tree changes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently, the wdt_reboot driver always gets its watchdog device
reference from an OF node. This prevents selecting a watchdog at
runtime. Move the watchdog device reference to the plat data, so
the driver can be bound with the reference pre-provided. The
reference will still be acquired from the OF node if it is not
already provided.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
These driver probe functions are not (and should not be) called from
outside the respective driver source files. Therefore, the functions
should be marked static.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
None of the sysreset drivers do anything beyond providing sysreset
uclass ops. They should depend on the sysreset uclass.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When allocate the GPD ring, and tell its address to the controller, then
the driver starts or resumes the QMU, the controller will try to access
the first GPD, so need flush the first one to avoid wrong GPD status.
Reported-by: Xin Lin <Xin.Lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
According to the Armada 3720 Functional Specification Data Strobe applies
for both read and write config requests.
Data strobe bits configure which bytes from the start address should be
returned for read request. Set value 0xf (all 4 bits) into Data Strobe
register to read all four bytes from specified 32-bit config space
register. Same value for Data Strobe register is programmed by Linux
pci-aardvark.c driver for config read requests.
Without this patch pci-aardvark driver sets data strobe register only
during config write operations. So any followup config read operations
could result with just partial datai returned (if previous write operation
was not 32-bit wide). This patch fixes it and ensures that config read
operations always read all bytes from requested register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a pci driver, not an eth driver.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Root Complex should be the default mode, let's set it explicitly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge is working, U-Boot's CONFIG_PCI_PNP code automatically
enables memory access and bus mastering when it is needed. So do not
prematurely enable memory access and bus mastering.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Bridge is always accessible also when link is down. So move detection
of link up from mvebu_pcie_of_to_plat() function to mvebu_pcie_valid_addr()
function which is used when accessing PCI config space.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Functions mvebu_pcie_get_local_bus_nr() and mvebu_pcie_get_local_dev_nr()
are not used, so remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The mysterious "Memory controller" PCI device which is present in PCI
config space is improperly configured and crippled PCI Bridge which acts
as PCIe Root Port for endpoint PCIe card.
This PCI Bridge reports in PCI config space incorrect Class Code (Memory
Controller) and incorrect Header Type (Type 0). It looks like HW bug in
mvebu PCIe controller but apparently it can be changed via mvebu registers
to correct values.
The worst thing is that this PCI Bridge is crippled and its PCI config
registers in range 0x10-0x34 alias access to internal mvebu registers which
have different functionality as PCI Bridge registers. Moreover,
configuration of PCI primary and secondary bus numbers (registers 0x18
and 0x19) is done via totally different mvebu registers via totally strange
method and cannot be done via PCI Bridge config space.
Due to above fact about PCI config range 0x10-0x34, allocate a private
cfgcache[] buffer in the driver, to which PCI config access requests to
the 0x10-0x34 space will be redirected in mvebu_pcie_read_config() and
mvebu_pcie_write_config() functions. Function mvebu_pcie_write_config()
will also catch writes to PCI_PRIMARY_BUS (0x18) and PCI_SECONDARY_BUS
(0x19) registers and set PCI Bridge primary and secondary bus numbers via
mvebu's own method.
Also, Expansion ROM Base Address register (0x38) is available, but at
different offset 0x30. So recalculate register offset before accessing PCI
config space.
After these steps U-Boot sees working PCI Bridge and CONFIG_PCI_PNP code
can finally start enumerating all PCIe devices correctly, even with more
complicated PCI topology. So update also mvebu_pcie_valid_addr() function
to reflect state of the real device topology.
Each PCIe port is de-facto isolated and every PCI Bridge which is part of
PCIe Root Complex is also isolated, so put them on separate PCI buses as
(local) device 0.
U-Boot already supports enumerating separate PCI buses, real (HW) bus
number can be retrieved by "PCI_BUS(bdf) - dev_seq(bus)" code, so update
config read/write functions to properly handle more complicated tree
topologies (e.g. when a PCIe switch with multiple PCI buses is connected
to the PCIe port).
Local bus number and local device number on mvebu are used for determining
which config request type is used (Type 0 vs Type 1). On normal non-broken
PCIe hardware it is done by primary and secondary bus numbers. So correctly
translate settings between these numbers to ensure that correct config
requests are sent over the PCIe bus.
As bus numbers are correctly re-configured, it does not make sense to print
some initial bogus configuration during probe, so remove this debug code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
When reading 8 or 16 bits from config space, use appropriate readb() or
readw() calls. This ensures that PCIe controller does not read more bits
from endpoint card as asked by read_config() function.
Technically there should not be an issue with reading data from config
space which are not later used as there are no clear-by-read registers.
But it is better to use correct read operation based on requested size.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Current implementation of write_config() is broken for PCI_SIZE_8 or
PCI_SIZE_16 as it always uses writel(), which means that write operation
is always 32-bit, so upper 24 bits for PCI_SIZE_8 and upper 16 bits for
PCI_SIZE_16 are cleared.
Fix this by using writeb() and writew(), respectively.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently driver supports only version 1 and 2.
Version 5 has slightly different registers structure
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Generic Interface (GENI) Serial Engine (SE) based uart
can be found on newer qualcomm SOCs, starting from SDM845.
Tested on Samsung SM-G9600(starqltechn)
by chain-loading u-boot with stock bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
The DART is an IOMMU that is used on Apple's M1 SoC. This driver
configures the DART such that it operates in bypass mode which is
enough to support DMA for the USB3 ports integrated on the SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Apple M1 SoCs include an S5L UART which is a variant of the S5P
UART. Add support for this variant and enable it by default
on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uclass is intended to manage IOMMUs on systems where the
IOMMUs are not in bypass mode by default. In that case U-Boot
cannot ignore the IOMMUs if it wants to use devices that need
to do DMA and sit behind such an IOMMU.
This initial IOMMU uclass implementation does not implement and
device ops and is intended for IOMMUs that have a bypass mode
that does not require address translation. Support for IOMMUs
that do require address translation is planned and device ops
will be defined when support for such IOMMUs will be added.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
dev_err seems to be moved to different header file. Include
dm/device_compat.h file to compile properly.
Fixes: 69dae8902b ("linux/compat.h: Remove redefinition of dev_xxx macros")
Signed-off-by: Stefan Agner <stefan@agner.ch>
There are 4 registers (PERIPHID{0-3}) that contain the ID of MCI.
For MMCs' with peripheral id 0x02041180 and 0x03041180, H/W flow control
needs to be enabled for multi block writes (MMC CMD 18).
Signed-off-by: Usama Arif <usama.arif@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix branching to avoid premature falling back on a long timeout instead
of continuation of the initialization attempt.
Clear of the comment to avoid the ambiguity.
Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Adds an implementation of the wait_dat0 MMC operation for the DM SDHCI
driver, allowing the driver to continue when the card is ready rather
than waiting for the worst case time on each MMC switch operation.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Adds an implementation of the wait_dat0 MMC operation for the Freescale
eSHDC driver, allowing the driver to continue when the card is ready
rather than waiting for the worst case time on each MMC switch operation.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
The DFU_MTD Kconfig entry is in the wrong position, move it into the
correct alphabetically sorted position. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Not all SPI flashes and controllers can do continuous transfer longer
than 16 MiB, so perform the DFU read in 16 MiB chunks.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Allwinner R329 has no MMC2.
Only include the code of MMC2 if the base address of it is defined.
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This driver supports the sun4i/sun6i/sun20i watchdog timers.
They have a maximum timeout of 16 seconds.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The sunxi clock driver exposes a reset controller, so it selects the
reset controller framework. Ensure that dependency is also satisfied
when building the driver for the SPL.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The AXP PMICs have the ability to power off the system. The existing
code for this is duplicated for each PMIC variant, and uses the legacy
non-DM "pmic_bus" interface. When SYSRESET is enabled, this can all be
replaced with a sysreset device using the DM_PMIC interface.
Since the trigger bit is the same on all PMIC variants, use the register
definitions from the oldest supported PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The sysreset uclass has an option to provide the do_poweroff() function.
When that option is enabled, the AXP power drivers should not provide
their own definition.
For the AXP305, which is paired with 64-bit systems where TF-A provides
PSCI, there is another possible conflict with the PSCI firmware driver.
This driver can be enabled even if CONFIG_PSCI_RESET is disabled, so
make sure to use the right symbol in the condition.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The device tree binding provides for getting VBUS state from a device
referenced by phandle, as an optional alternative to using a GPIO. In
U-Boot, where there is no power supply class, this VBUS detection will
be implemented using a regulator device and its get_enable method.
Let's hook this up to the PHY driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Linux driver checks the VBUS detection GPIO first; then VBUS power
supply; then finally assumes VBUS is present. When adding VBUS power
supply support, we want to match that order, so we get the same behavior
in case both a GPIO and a power supply are provided in the device tree.
So refactor the function a bit to remove the early return, and use the
same "assume VBUS is present" final fallback.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Both of these messages log the GPIO number of the ID detection GPIO,
which is not terribly useful, especially in the VBUS detection function.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
With current implementation we are seeing write issues at low frequencies
below 15Mhz. Make below changes to fix the issue.
1. Remove dummy genfifo entry in zynqmp_qspi_chipselect() which was
incorrectly added in the past
2. Enable and poll for TX_FIFO_Empty after Tx data is filled in FIFO in
zynqmp_qspi_fill_tx_fifo().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1634652780-21755-1-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Errata ERR050568 description says that "Flash access by FlexSPI AHB
command may not work with platform frequency equal to 300 MHz" on
LS1028A.
By default, smaller length reads(equal to RX FIFO size) are done by IP
bus and larger length reads using AHB bus. For adding errata workaround,
use IP bus to read entire flash contents and disable AHB path when
platform frequency is 300Mhz.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for disabling AHB bus and read entire flash contents via IP
bus only. Please note, this enables IP bus read using a quirk which can
be enabled directly in device-type data or in existence of an errata
where AHB bus may need to be disabled.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The mt25qu512a supports 4K or 64K sectors, so adding
SECT_4K to enable 4K sector usage.
Tested on Intel n5x hardware with QSPI carrier card
Signed-off-by: Kris Chaplin <kris.chaplin@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
[jagan: droped Tested-by of patch author and datasheet link]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add is25lp512 and is25wp512 devices to spi-nor id table
Tested on Intel n5x hardware with QSPI carrier card
Signed-off-by: Kris Chaplin <kris.chaplin@linux.intel.com>
[jagan: droped Tested-by of patch author]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The original purpose of mtd_erase_callback() in Linux at the time it was
imported to U-Boot, was to inform the caller that erasing is done (since
it was an asynchronous operation).
All supplied callback methods in U-Boot do nothing, but the
mtd_erase_callback() function was (until previous patch) grossly abused
in U-Boot's mtdpart implementation for completely different purpose.
Since we got rid of the abusement, remove the mtd_erase_callback()
function and the .callback member from struct erase_info entirely, in
order to avoid such problems in the future.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The _erase() method of the mtdpart driver, part_erase(), currently
implements offset shifting (for given mtdpart partition) in a weird way:
1. part_erase() adds partition offset to block address
2. parent driver's _erase() method is called
3. parent driver's _erase() method calls mtd_erase_callback()
4. mtd_erase_callback() subtracts partition offset from block address
so that the callback function is given correct address
The problem here is that if the parent's driver does not call
mtd_erase_callback() in some scenario (this was recently a case for
spi_nor_erase(), which did not call mtd_erase_callback() at all), the
offset is not shifted back.
Moreover the code would be more readable if part_erase() not only added
partition offset before calling parent's _erase(), but also subtracted
it back afterwards. Currently the mtd_erase_callback() is expected to do
this subtracting since it does have to do it anyway.
Add the more steps to this procedure:
5. mtd_erase_callback() adds partition offset to block address so that
it returns the the erase_info structure members as it received them
6. part_erase() subtracts partition offset from block address
This makes the code more logical and also prevents errors in case
parent's driver does not call mtd_erase_callback() for some reason.
(BTW, the purpose of mtd_erase_callback() in Linux is to inform the
caller that it is done, since in Linux erasing is done asynchronously.
We are abusing the purpose of mtd_erase_callback() in U-Boot for
completely different purpose. The callback function itself has empty
implementation in all cases in U-Boot.)
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
May it possible to interrupt the spi_nor_erase() function.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
The spi_nor_erase() function does not call mtd_erase_callback() as it
should.
The mtdpart code currently implements the subtraction of partition
offset in mtd_erase_callback().
This results in partition offset being added prior calling
spi_nor_erase(), but not subtracted back on return. The result is that
the `mtd erase` command does not erase the whole partition, only some of
it's blocks:
=> mtd erase "Rescue system"
Erasing 0x00000000 ... 0x006fffff (1792 eraseblock(s))
jedec_spi_nor spi-nor@0: at 0x100000, len 4096
jedec_spi_nor spi-nor@0: at 0x201000, len 4096
jedec_spi_nor spi-nor@0: at 0x302000, len 4096
jedec_spi_nor spi-nor@0: at 0x403000, len 4096
jedec_spi_nor spi-nor@0: at 0x504000, len 4096
jedec_spi_nor spi-nor@0: at 0x605000, len 4096
jedec_spi_nor spi-nor@0: at 0x706000, len 4096
This is obviously wrong.
Add proper calling of mtd_erase_callback() into the spi_nor_erase()
function.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reported-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
This check is already done in all callers: mtdcore's mtd_write() /
mtd_erase(), legacy spi_nor_write() / spi_flash_erase(). No reason to do
this here as well.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The cleanup code of spi_nor_erase() function calls write_disable(), but
does not return it's return value even in case of failure. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
The cleanup code of the spi_nor_erase() function overwrites the ret
variable with return value of clean_bar(), even if the ret variable is
already set. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
The spi_nor_erase() function does not check return value of the
write_enable() call. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Use the cleanup codepath of spi_nor_erase() also in the event of failure
of writing the BAR register.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
The S25FL256L is a part of the S25FL-L family and has the same feature set
as S25FL128L except the density.
The datasheet can be found in the following link.
https://www.cypress.com/file/316171/download
The S25FL256L is 32MB NOR Flash that does not support Bank Address
Register. This fixup is activated if CONFIG_SPI_FLASH_BAR is enabled and
returns ENOTSUPP in setup() hook to avoid further ops.
Tested on Xilinx Zynq-7000 FPGA board.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
When a caller is not interested in the returned message, the ret_payload
pointer is set to NULL in the u-boot-sources. In this case, under EL3, the
memory from address 0x0 would be overwritten by ipi_req() with the returned
IPI message, damaging the original data under this address. The patch, in
case ret_payload is NULL, assigns the pointer to the array holding the IPI
message being sent.
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Adrian Fiergolski <Adrian.Fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/3178ff7651948270b714daa4adad48b94eaca9ba.1634309856.git.michal.simek@xilinx.com
Mini emmc does not use any pmufw and ZYNQMP_FIRMWARE is disabled.
xilinx_pm_request() will not be compiled and causes undefined reference to
`xilinx_pm_request' error. So add a weak function in zynq_sdhci.c file.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1633086518-32636-1-git-send-email-t.karthik.reddy@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As stated in comment above the code, CRS response can be returned to OS
only for 4-byte PCI_VENDOR_ID config read request. So fix the code.
Fixes: 1d7ad68559 ("arm: a37xx: pci: Handle propagation of CRSSVE bit from PCIe Root Port")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Bridge which represents Aardvark PCIe Root Port does not have
configurable bars.
So ensure that write operation to bars registers on PCI Bridge is noop and
bars registers always contain zero address which indicates that bars are
unsupported.
After this change U-Boot 'pci bar 0.0.0' command does not show any
allocated bars for PCI Bridge device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: cb056005dc ("arm: a37xx: pci: Add support for accessing PCI Bridge on root bus")
Reviewed-by: Stefan Roese <sr@denx.de>
Move the config option CONFIG_I2C_MV to a Kconfig option
CONFIG_SYS_I2C_MV and move the default definition from config header
files into defconfigs.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The following warning is seen in sifive_ddr.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_index_ptr().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The following warning is seen in macb.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_index_ptr(), or cast with uintptr_t.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
At present there is only devfdt_get_addr_ptr() which only returns
the first <addr, size> pair in the 'reg' property. Add a new API
devfdt_get_addr_index_ptr() to return the indexed pointer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The following warning is seen in ocores_i2c.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_ptr().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
dev_read_addr() returns a value of type fdt_addr_t which is a 64-bit
address and plat->base is a pointer. In a 32-bit build, this causes the
following warning seen when building sifive-gpio.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_ptr().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
dev_read_addr() returns a value of type fdt_addr_t which is a 64-bit
address and pd->va is a pointer. In a 32-bit build, this causes the
following warning seen when building sifive-prci.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_ptr().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The following warning is seen in cache-sifive-ccache.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Fix by casting it with uintptr_t.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
commit 6bf6d81c11 ("clk: fixed_rate: add dummy enable() function")
implemented .enable, so fixed rate clocks can be used where drivers
might call clk_enable(). Implement the .disable op for the same reason;
some drivers, e.g. USB PHYs, may attempt to disable clocks at runtime.
Signed-off-by: Samuel Holland <samuel@sholland.org>
On mvebu this is defined if and only if !ARM64.
Otherwise it is defined for boards with ARCH_MX23, ARCH_TEGRA and
ARCH_ZYNQ, and also for SOC_AR934X (tplink_wdr4300).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This option is only used for
mx23evk_defconfig
mx23_olinuxino_defconfig
which are the only i.MX23 boards.
Add depend on ARCH_MX23 and default to y.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
In preparation for moving this option to Kconfig, rename it to be
consistent with other USB EHCI Kconfig options.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The default configuration of rk3399 EMMC PHY does not enable the
strobe line, and EMMC controller will got data transmission error
at HS400 mode.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
fix up ppll init freq.
support tclk_emmc.
add freq (26M) for mmc device.
fix up the sfc clk rate unit error.
Change in V2:
remove change id.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Using read_poll logic.
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set clock related processing into set_speed logic. And Optimize
printing format.
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Starting with commit 92f1e9a4b3 ("clk: Detect failure to set
defaults") the clk driver for the PX30 for the Odroid Go Advance would
no longer probe correctly, because setting the cpll and gpu clocks are
not supported with the clk_px30 U-Boot driver. This adds support for
setting the cpll clock to the clk_px30 driver. Another patch will
update the U-Boot specific device-tree to remove the GPU clock which is
not used by U-Boot.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Function dm_pci_hose_probe_bus() expects that bus is valid PCI device with
Bridge header type (0x01). So add check before touching PCI config space to
prevent misconfiguring some non-standard device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Rom Address is currently supported only for Normal (0x00) and
Bridge (0x01) header types. Fix code accordingly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The current code invalidates the range after the read buffer since the
buffer pointer gets incremented in the read loop. Use a temporary
pointer to make sure we have a pristine pointer to invalidate the
correct memory range after read.
Fixes: 704e040a51 ("nvme: Apply cache operations on the DMA buffers")
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
The DS1307 driver was originally based on the DS1337 driver. However,
the functionality of the clock set/get functions has diverged. In the
original DS1337 driver, the set/get functions did the following:
1) Setting the clock ensured the oscillator was enabled.
2) Getting the clock checked and reset the oscillator-stop flag.
The DS1307 does not have an oscillator-stop flag, but the driver tried
(incorrectly) to emulate this by ensuring the oscillator was running. It
really makes no sense to start a stopped clock without setting it.
This patch makes the DS1307 driver behave like the original DS1337
driver again. For the DS1307 itself, this is just a removal of code,
since there is no oscillator-fail bit to check or reset, and the clock
is started when it is set. Since the DS1307 driver can now also be used
for the DS1337 and DS1340 which do have this bit, add code to handle the
oscillator-stop bit in the same was the original DS1337 driver did --
i.e. report that the oscillator had stopped and clear the flag.
This means that setting the date using the date command (which does both
a get and a set) will now clear the oscillator-stop flag in addition to
setting and starting the clock.
The old-style (non-DM) code has not been updated and will be removed in
a future patch. Note that this older code does not support the DS1337,
as there is a separate driver for this. Also note that the original (DM)
code used the wrong control-register address for the DS1337.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Add a driver for Macronix raw NAND controller.
This patch referred from linux mxic_nand.c. The difference from the
linux version is described here.
1. In order to adapt to the uboot nand framework, add function
binding (cmdfunc, read_byte, read_buf, write_buf).
2. Added parsing command format to use hardware correctly.
3. Remove the incompatible functions of Uboot.
Signed-off-by: Zhengxun Li <zhengxunli@mxic.com.tw>
strlcat() need to be passed the full buffer length. The incorrect call
caused truncation of partition names for fastboot_raw_partition_... and
fastboot_partition_alias_... env lookup to much less than PART_NAME_LEN.
Fixes: 69a7529831 ("fastboot: Fix possible buffer overrun")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFlfXAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyHzuB/4pV2iAeFBjNf6YYsuk
uvBQm7+j+AQzy0J337bDwulvw8wTKKlaid4qfOpEjW316DI9oXN1bXTlwNsjtQvO
zTILW7MoBjDRhZHsSkeSfIuD+Sc80juAoLBv+GXskQdZOTQUbWdmi2o60gdY5Ba4
WN0i4zOGVqd7xoDuDgM3XC1M2RnKerxDeVt20Ji+5dFfmes11m7br6sWj2j/45f+
q3G1ufHl+ea+8oRLZGjn2ddKCb1wLLOrNZA+74dsZ5SN0LCN0vFsE3+JAk4RZ2A5
omiHVApjE+J3vAjwiVY7apjcIdVEeyb5AioiXSBAEZiq1l1UI7eKDQT75bDkaKSs
4wBV
=78ME
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.01-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.01 cycle:
This small feature set adds the support for PWM driver for the sama5d2
SoC. It also adds a node in the DT for this SoC.
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
Add usb_gadget_handle_interrupts(), usb_gadget_register_driver()
and usb_gadget_unregister_driver() to be able to test
binding usb gadget.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add an entry in usb_gadget_controller_number() for the DWC2
gadget controller. It is used to bind the USB Ethernet driver.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Fix a regression brings by commit 84f8e36f03 ("cmd: bind: allow to
bind driver with driver data")
As example, the following bind command doesn't work:
bind /soc/usb-otg@49000000 usb_ether
As usb_ether driver has no compatible string, it can't be find by
lists_bind_fdt(). In bind_by_node_path(), which called lists_bind_fdt(),
the driver entry is known, pass it to lists_bind_fdt() to force the driver
entry selection.
For this, add a new parameter struct *driver to lists_bind_fdt().
Fix also all lists_bind_fdt() callers.
Fixes: 84f8e36f03 ("cmd: bind: allow to bind driver with driver data")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).
Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.
This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the rsb functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants, so move that to the common header.
There are only a couple of pairs of hardware/runtime addresses used
across all PMIC variants. So far the code expected only the "primary"
pair, but some PMICs like the AXP305 and AXP805 use the secondary pair,
so add support for that to the DM driver as well.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the p2wi functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants. Move that to the common header, so it can be used by
both interface implementations.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
These PMICs provide some combination of battery charger, fuel gauge,
GPIOs, regulators, and VBUS routing. These functions are represented
as child nodes in the device tree. Add the minimal driver needed to
probe these child devices and provide the DM_PMIC ops.
Enable the driver by default for SoCs that normally pair with a PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that there is a separate symbol to enable DM_PMIC in SPL, update the
the SPL-specific driver symbols to depend on this new option.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Kconfig symbols for two PMIC drivers (PMIC_AS3722 and DM_PMIC_MC34708)
were missing a dependency on DM_PMIC. To fix this inconsistency, and to
keep it from happening again, wrap the driver section with "if DM_PMIC"
instead of using a "depends on DM_PMIC" clause for each driver.
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.
Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the clk_ti_am3_dpll_round_rate() attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.
Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Add a driver so the clocks/resets for these peripherals (especially I2C,
RSB, and UART) can be enabled using the normal uclass methods.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, the I2C clocks are configured in the sunxi board code. Add
the I2C clocks to the DM clock driver so they can be enabled from the
DM I2C driver using the normal uclass methods.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since the beginning, all banks have had space for 32 pins, even when
not all pins were implemented. Let's use a single constant for the GPIO
bank size here, like the GPIO driver is already doing.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This clarifies which callers must be updated to complete the DM_GPIO
conversion.
The only remaining caller of name_to_gpio in generic code is inside the
!DM_GPIO block in cmd/gpio.c. DM_GPIO is always selected on sunxi, so
that code cannot be reached. And after this commit, there are only two
remaining implementations of name_to_gpio.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The only caller of this function was the MMC pinmux code, which used it
to parse a string given from a Kconfig symbol. As the Kconfig symbol has
been converted to a Boolean, this function is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The CCU header is only used by the DM drivers, not any platform code.
Its current location adds an artificial dependency on CONFIG_ARM and
ARCH_SUNXI, which will be problematic when adding the CCU driver for
a RISC-V sunxi platform.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Move CONFIG_VIDEO_MXS from board headers to Kconfig
and drop it from obsolete cfb_console driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for 30bpp mode where pixels are picked in 32-bit
integers but use 10 bits instead of 8 bits for each component.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
This ID disappeared in 5b66fdb29d ("mtd: spi: Remove unused files"),
add the ID back, since the chip is used on devices supported by U-Boot.
Fixes: 5b66fdb29d ("mtd: spi: Remove unused files")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to datasheet, the upper four bits are reserved or used for
reflecting the ECC status of the accumulated pages. The error bits
number for the worst segment of the current page is encoded on lower
four bits. Fix it by masking the upper bits.
This same issue has been already fixed in the linux kernel by:
"mtd: spinand: macronix: Fix ECC Status Read"
(sha1: f4cb4d7b46f6409382fd981eec9556e1f3c1dc5d)
Apply the same fix in the U-Boot driver.
Signed-off-by: Haolin Li <li.haolin@qq.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Compute i2cclk only one time in stm32_i2c_compute_timing()
and remove setup parameter (accessible in i2c_priv).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the support for the i2c-digital-filter binding, allowing to enable
the digital filter via the device-tree and indicate its value in the DT
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The digital filter related computation are present in the driver
however the programming of the filter within the IP is missing.
The maximum value for the DNF is wrong and should be 15 instead of 16.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Replace driver internally coded enabling/disabling of the
analog-filter with the DT binding "i2c-analog-filter".
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Today all the I2C instance point on the same global
variable stm32_i2c_setup according the compatible: i2c_priv->setup =
pointer to the same driver data.
This patch changes this driver data (stm32f7_setup and stm32mp15_setup)
to a const struct and move the timing struct 'setup' as element of i2c
privdata, initialized in stm32_ofdata_to_platdata() with the driver
configuration data.
This patch solves issues when several I2C instance have not the same
clock source or not the same configuration: each timing setup is saved
is the I2C privdata.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
There were several changes for this structure but the documentation was
not changed at the time. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge (PCIe Root Port) for Aardvark is emulated in U-Boot,
add support for handling and propagation of CRSSVE bit.
When CRSSVE bit is unset (default), driver has to reissue config
read/write request on CRS response.
CRSSVE bit is supported only when CRSVIS bit is provided in read-only
Root Capabilities register. So manually inject this CRSVIS bit into read
response for that register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge is working for the PCIe Root Port, U-Boot's PCI_PNP
code automatically enables memory access and bus mastering when needed.
We do not need to enable it when setting the HW up.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Aardvark does not have a real PCIe Root Port device on the root bus.
Instead it has PCIe registers of PCIe Root Port device mapped in
internal Aardvark memory space starting at offset 0xc0.
The PCIe Root Port itself is normally available as a PCI Bridge device
on the root bus with bus number zero. Aardvark instead has the
configuration registers of this PCI Bridge at offset 0x00 of Aardvark's
memory space, but the class code of this device is Mass Storage
Controller (0x010400), instead of PCI Bridge (0x600400), which causes
U-Boot to fail to recognize it as a P2P Bridge
Add a hook into the pcie_advk_read_config() / pcie_advk_write_config()
functions to redirect access for root bus from PIO transfer to this
internal Aardvark memory space. This will allow U-Boot to access
configuration space of this PCI Bridge which represents PCIe Root Port.
Redirect access to PCI Bridge registers in range 0x10 - 0x34 to driver's
internal buffer (cfgcache[]). This is because at those addresses
Aardvark has different registers, incompatible with config space of a
PCI Bridge.
Redirect access to PCI Bridge register PCI_ROM_ADDRESS1 (0x38) to
Aardvark internal address for that register (0x30).
When reading PCI Bridge register PCI_HEADER_TYPE, set it explicitly to
value Type 1 (PCI_HEADER_TYPE_BRIDGE) as PCI Bridge must be of Type 1.
When writing to PCI_PRIMARY_BUS or PCI_SECONDARY_BUS registers on this
PCI Bridge, correctly update driver's first_busno and sec_busno
variables, so that pcie_advk_addr_valid() function can check if address
of any device behind the root bus is valid and that PIO transfers are
started with correct config type (1 vs 0), which is required for
accessing devices behind some PCI bridge after the root bus.
U-Boot's PCI_PNP code sets primary and secondary bus numbers as relative
to the configured bus number of the root bus. This is done so that
U-Boot can support multiple PCIe host bridges or multiple root port
buses, when internal bus numbers are different.
Now that root bus is available, update code in pcie_advk_read_config()
and pcie_advk_write_config() functions to correctly calculate real
Aardvark bus number of the target device from U-Boot's bus number as:
busno = PCI_BUS(bdf) - dev_seq(bus)
Stefan: Small fix of header masking as suggested by Pali.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Aardvark reports Disabled and Hot Reset LTSSM states as values >= 0x20.
Link is not up in these states, so fix pcie_advk_link_up() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Subroutines in comphy_usb2_power_up() and comphy_sgmii_power_up() functions
may fail. In this case, do not continue execution of current function and
instead jump to the end. Return value in 'ret' variable is already set.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
phy_txd_inv or phy_rxd_inv needs to be set only in case when
appropriate polarity is inverted. Otherwise these bits should be
cleared.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9406
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marvell Armada 3700 Functional Specifications, section 52.2 PCIe Link
Initialization says that TXDCLK_2X_SEL bit needs to be enabled for PCIe
Root Complex mode.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9408
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the CONFIG_STM32_FLASH to Kconfig by using
tools/moveconfig.py
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add protection on presence and order of the phy node sub node
by using the mandatory reg information.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The vbus-supply is an optional property of sub-node connector node.
and no more in the usb phyc node (in first proposed binding).
This regulator for USB VBUS may be needed for host mode.
See the latest kernel binding for details in
Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml.
usbphyc_port0: usb-phy@0 {
reg = <0>;
phy-supply = <&vdd_usb>;
#phy-cells = <0>;
connector {
compatible = "usb-a-connector";
vbus-supply = <&vbus_sw>;
};
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Import HS400 support for iMX7ULP B0 from the Linux kernel:
2eaf5a533afd ("mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP")
According to IC suggest, need to clear the STROBE_DLL_CTRL_RESET
before any setting of STROBE_DLL_CTRL register.
USDHC has register bits(bit[27~20] of register STROBE_DLL_CTRL)
for slave sel value. If this register bits value is 0, it needs
256 ref_clk cycles to update slave sel value. IC suggest to set
bit[27~20] to 0x4, it only need 4 ref_clk cycle to update slave
sel value. This will short the lock time of slave.
i.MX7ULP B0 will need more time to lock the REF and SLV, so change
to add 5us delay.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
This allows removal of the OCOTP driver when SPL is enabled.
Disabling OCOTP reduces SPL size efficiently.
Signed-off-by: Michael Scott <mike@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The RX8803 and RX8900 register layouts are compatible with the one of
the RV8803. So add these to the compatibles.
The same compatible strings are used and approved in linux kernel.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Since the mxs_nand_spl has implemented adjust read offset in
nand_spl_load_image, so we don't need to check the bad block in
nand_spl_adjust_offset. Directly return the offset to continue
read by nand_spl_load_image.
Signed-off-by: Ye Li <ye.li@nxp.com>
The SD clock disable is wrapped by MMC_SUPPORTS_TUNING. So it
only works when UHS is enabled. However, in SD initialization the
power cycle does not depends on UHS. But the power cycle needs
disable the SD clock before power down.
So this causes a problem when UHS is not enabled. Some cards can't
become ready (ACMD14 timeout) due to the clock is enabled during
power cycle.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- pcie_dw_meson: fix usb fail when pci link fails to go up
- Sync Amlogic DT from Linux 5.14
- dwc3-meson-gxl: add AXG compatible
- dts: keep back HW order for MMC devices since change in Upstream Linux
- Cleanup local AXG DT USB nodes now everything is upstream
- distro_bootcmd: run pci enum for scsi_boot just like it is done for nvme_boot
- New Boards:
- Odroid-HC4: a variant of Odroid-C4 with 2 SATA ports (via PCIe-SATA bridge)
- Beelink GS-King X: A variant of the other Beelink board with 2 SATA ports (via USB3-SATA bridge)
- Banana Pi M5: another credit card SBC
- JetHub D1/H1: home automation controllers
- Radxa Zero: another RPi Zero sized SBC
-----BEGIN PGP SIGNATURE-----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=pDip
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20211007' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Add new SoC ID for S905Y2 found in Radxa Zero
- pcie_dw_meson: fix usb fail when pci link fails to go up
- Sync Amlogic DT from Linux 5.14
- dwc3-meson-gxl: add AXG compatible
- dts: keep back HW order for MMC devices since change in Upstream Linux
- Cleanup local AXG DT USB nodes now everything is upstream
- distro_bootcmd: run pci enum for scsi_boot just like it is done for nvme_boot
- New Boards:
- Odroid-HC4: a variant of Odroid-C4 with 2 SATA ports (via PCIe-SATA bridge)
- Beelink GS-King X: A variant of the other Beelink board with 2 SATA ports (via USB3-SATA bridge)
- Banana Pi M5: another credit card SBC
- JetHub D1/H1: home automation controllers
- Radxa Zero: another RPi Zero sized SBC
Upstream Linux uses the "amlogic,meson-axg-usb-ctrl" for AXG SoCs.
This adds it to the compatible list for this driver.
Reported-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Vyacheslav Bocharov <adeep@lexina.in>
On Amlogic A311D, when the PCIe link fails disabling the related clocks
makes USB fail. For an unknown reason, this doesn happen on the S905D3 SoC.
Mimic the Linux behavior by not considering a link failure a probe failure,
and continue even if the PCIe link is down.
Reported-by: Art Nikpal <email2tema@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Provide sysreset driver using the SBI system reset extension.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Samuel Holland <samuel@sholland.org>
The RISC-V SBI interface v0.1 provides a function for printing a
character to the console. Even though SBI v0.1 functions are deprecated,
the SBI console is quite useful for early debugging, because it works
without any dcache, memory, or MMIO access in S mode.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In some cases, the best config cannot be used because the VCO would be
out-of-spec. In these cases, we may need to try a worse combination of r/od
in order to find the best representable config. This also adds a few test
cases to catch this and other (possible) unlikely errors.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Everything here sits in a while (true) loop. However, this introduces a
couple of layers of indentation. We can simplify the code by introducing a
single goto instead of using continue/break. This will also make adding
loops in the next patch easier.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The PLL functions take ulong arguments for rate, but still check if that
rate is negative (which is never true). The correct way to handle this is
to use IS_ERR_VALUE (like is already done in k210_clk_set_rate). While
we're at it, we can move the error checking up into the caller of the pll
set/get rate functions. This also protects our other calculations from
using bogus values for rate.
Fixes: 609bd60b94 ("clk: k210: Rewrite to remove CCF")
Reported-by: Coverity Scan <scan-admin@coverity.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Use dev_ function to read the sides and colour to support a live tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use dev_ function to read the name and boolean to support a live tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The generic GPIO flags binding is shared across many drivers, some of
which need their own xlate function. Factor out the flag translation
code from gpio_xlate_offs_flags so it does not need to be duplicated.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Translation of an OF GPIO specifier should fail if the pin offset is
larger than the number of pins in the GPIO bank.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Translation of a pin name to a device+offset should fail if the offset
is larger than the number of pins in the GPIO bank.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Parse different gpio properties from dt as part of probe
function. This detail is required to enable pinctrl pad
later when gpio lines are requested.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Acked-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Both dummy.nbytes and dummy.buswidth may be zero. By not checking
the later, it is possible to trigger division by zero and a crash.
This does happen with tiny SPI NOR framework in SPL. Fix this by
adding the check and returning zero dummy bytes in such a case.
Fixes: 38b0852b0e ("spi: cadence-qspi: Add support for octal DTR flashes")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
[trini: Drop Pratyush's RB as his requested changes weren't made as
Marek disagreed]
To avoid the need of extra boot scripting on AM65x for loading a
watchdog firmware, add the required rproc init and loading logic for the
first R5F core to the watchdog start handler. In case the R5F cluster is
in lock-step mode, also initialize the second core. The firmware itself
is embedded into U-Boot binary to ease access to it and ensure it is
properly hashed in case of secure boot.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
The board is responsible for providing the firmware as additional
loadable via the U-Boot fit image. The driver will pick up its location
from /fit-images/k3-rti-wdt-firmware then.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The function prototype for ft_pci_setup is inside fdt_support.h, we need
to include that header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid a build warning with W=1, provide a function prototype for
dm_pciauto_prescan_setup_bridge, which is a non-static function whose
definition is inside pci_auto.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Writing of individual registers was not functioning
correctly as a 0 'offset' byte under DM-managed
I2C was being appended in front of register we
wanted to access.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The RX8025/RX8035 does not like having it's time registers
set byte-by-byte in separate I2C transactions.
From the note at the top of the file, it appears
target-dependent workarounds have been used in the
past for this.
Resolve this by setting the time registers in a single
I2C transaction.
As part of this, also ensure the '24/12' flag in the RTC
is reset before writing the date (instead of after), otherwise
the RX8035 will clear the seconds and minutes registers.
Tested on Traverse Ten64 (NXP LS1088A) with RX8035.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The RX8035 is a newer model from EPSON which is
very similar in operation to the RX8025.
The changes mirror similar ones that will be
in Linux 5.15:
https://lore.kernel.org/all/20210709044518.28769-2-matt@traverse.com.au/
The UBOOT_DRIVER ID has also been corrected, previously
it declared itself as rx8010sj_rtc which is a different driver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
A search of the tree showed there is only one user
of this driver (soon to be two) - board/socrates
The second user will be the Traverse Ten64 board.
Both these boards have DM_RTC.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
We enforce that DM_SERIAL will have SYS_MALLOC_F enabled and so
SYS_MALLOC_F_LEN will have a value. Remove the build-time check.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last armada100 platform, remove that support
as well.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
=aQtT
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.01-rc1
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
Wdt expire command makes the wdt to count least possible ticks(1)
and expires immediately. Add expire_now option to the xlnx_wwdt_ops
and implement it by calling xlnx_wwdt_start() with minimum possible
count(1).
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1632808919-8600-3-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Existing driver uses generic watchdog mode which generates a signal to
PLM firmware, but the signal cannot be used to reset the system.
Change driver to use window watchdog basic mode. This window watchdog mode
generates a signal to PLM firmware which decides what action to take upon
expiry of watchdog.
Timeout value for xlnx_wwdt_start will come in milli seconds from wdt
framework. Make changes to load count value accordingly.
Add checks before loading the timer for min and max possible values.
Fix authour email id of Ashok Reddy Soma to long email id.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1632808919-8600-2-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Clocks should be enabled or disabled only if they are of GATE type
clocks. If they are not of GATE type clocks, don't touch them.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1632808827-6109-1-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
nand_dt_init() is still using fdtdec_xx() interface.
If OF_LIVE flag is enabled, dt property can't be get anymore.
Updating all fdtdec_xx() interface to ofnode_xx() to solve this issue.
For doing this, node parameter type must be ofnode.
First idea was to convert "node" parameter to ofnode type inside
nand_dt_init() using offset_to_ofnode(node). But offset_to_ofnode()
is not bijective, in case OF_LIVE flag is enabled, it performs an assert().
So, this leads to update nand_chip struct flash_node field from int to
ofnode and to update all nand_dt_init() callers.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Before e2e95e5e25 ("spi: Update speed/mode on change") most systems
silently defaulted to SF bus mode 0. Now the mode is always updated,
which causes breakage. It seems most SF which are used as boot media
operate in bus mode 0, so switch that as the default.
This should fix booting at least on Altera SoCFPGA, ST STM32, Xilinx
ZynqMP, NXP iMX and Rockchip SoCs, which recently ran into trouble
with mode 3. Marvell Kirkwood and Xilinx microblaze need to be checked
as those might need mode 3.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Cc: Andreas Biessmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Force the mtd name of spi-nor to "nor" + the driver sequence number:
"nor0", "nor1"... beginning after the existing nor devices.
This patch is coherent with existing "nand" and "spi-nand"
mtd device names.
When CFI MTD NOR device are supported, the spi-nor index is chosen after
the last CFI device defined by CONFIG_SYS_MAX_FLASH_BANKS.
When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated, this config
is replaced by to cfi_flash_num_flash_banks in the include file
mtd/cfi_flash.h.
This generic name "nor%d" can be use to identify the mtd spi-nor device
without knowing the real device name or the DT path of the device,
used with API get_mtd_device_nm() and is used in mtdparts command.
This patch also avoids issue when the same NOR device is present 2 times,
for example on STM32MP15F-EV1:
STM32MP> mtd list
SF: Detected mx66l51235l with page size 256 Bytes, erase size 64 KiB, \
total 64 MiB
List of MTD devices:
* nand0
- type: NAND flash
- block size: 0x40000 bytes
- min I/O: 0x1000 bytes
- OOB size: 224 bytes
- OOB available: 118 bytes
- ECC strength: 8 bits
- ECC step size: 512 bytes
- bitflip threshold: 6 bits
- 0x000000000000-0x000040000000 : "nand0"
* mx66l51235l
- device: mx66l51235l@0
- parent: spi@58003000
- driver: jedec_spi_nor
- path: /soc/spi@58003000/mx66l51235l@0
- type: NOR flash
- block size: 0x10000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "mx66l51235l"
* mx66l51235l
- device: mx66l51235l@1
- parent: spi@58003000
- driver: jedec_spi_nor
- path: /soc/spi@58003000/mx66l51235l@1
- type: NOR flash
- block size: 0x10000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "mx66l51235l"
The same mtd name "mx66l51235l" identify the 2 instances
mx66l51235l@0 and mx66l51235l@1.
This patch fixes a ST32CubeProgrammer / stm32prog command issue
with nor0 target on STM32MP157C-EV1 board introduced by
commit b7f060565e ("mtd: spi-nor: allow registering multiple MTDs when
DM is enabled").
Fixes: b7f060565e ("mtd: spi-nor: allow registering multiple MTDs when DM is enabled")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
[trini: Add <dm/device.h> to <mtd.h> for DM_MAX_SEQ_STR]
Signed-off-by: Tom Rini <trini@konsulko.com>
These functions can return errors, it's best to catch them and trigger
the driver unwind code path.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The two should be equivalent, but at the moment some platforms
(ls1021a-tsn.dts) use phy-mode only, which is not parsed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently the init_phy function may overwrite the priv->interface
property, since it calls tsec_get_interface which tries to determine it
dynamically based on default register values in ECNTRL.
Let's do that only if phy-connection-type happens to not be defined in
the device tree.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The felix driver runs only on NXP LS1028A, which most definitely does
not support the parallel 10G interface, just USXGMII, and that only up
to 2.5Gbps (toned down from 10 Gbps via symbol replication).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The enetc driver runs only on NXP LS1028A, which most definitely does
not support the parallel 10G interface, just USXGMII, and that only up
to 2.5Gbps (toned down from 10 Gbps via symbol replication).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
After the discussion here:
https://lore.kernel.org/netdev/20210603143453.if7hgifupx5k433b@pali/
which resulted in this patch:
https://patchwork.kernel.org/project/netdevbpf/patch/20210704134325.24842-1-pali@kernel.org/
and many other discussions before it, notably:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/1512016235-15909-1-git-send-email-Bhaskar.Upadhaya@nxp.com/
it became apparent that nobody really knows what "SGMII 2500" is.
Certainly, Freescale/NXP hardware engineers name this protocol
"SGMII 2500" in the reference manuals, but the PCS devices do not
support any "SGMII" specific features when operating at the speed of
2500 Mbps, no in-band autoneg and no speed change via symbol replication
. So that leaves a fixed speed of 2500 Mbps using a coding of 8b/10b
with a SERDES lane frequency of 3.125 GHz. In fact, "SGMII 2500 without
in-band autoneg and at a fixed speed" is indistinguishable from
"2500base-x without in-band autoneg", which is precisely what these NXP
devices support.
So it just appears that "SGMII 2500" is an unclear name with no clear
definition that stuck.
As such, in the Linux kernel, the drivers which use this SERDES protocol
use the 2500base-x phy-mode.
This patch converts U-Boot to use 2500base-x too, or at least, as much
as it can.
Note that I would have really liked to delete PHY_INTERFACE_MODE_SGMII_2500
completely, but the mvpp2 driver seems to even distinguish between SGMII
2500 and 2500base-X. Namely, it enables in-band autoneg for one but not
the other, and forces flow control for one but not the other. This goes
back to the idea that maybe 2500base-X is a fiber protocol and SGMII-2500
is an MII protocol (connects a MAC to a PHY such as Aquantia), but the
two are practically indistinguishable through everything except use case.
NXP devices can support both use cases through an identical configuration,
for example RX flow control can be unconditionally enabled in order to
support rate adaptation performed by an Aquantia PHY. At least I can
find no indication in online documents published by Cisco which would
point towards "SGMII-2500" being an actual standard with an actual
definition, so I cannot say "yes, NXP devices support it".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
To avoid a warning with W=1 about this function not having a previous
prototype, declare it as static, because it is not used outside of this
translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Make sure that the link status returned by phy_startup() is propagated
to the .start() method of struct eth_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
It is an unfortunate reality that some PHY settings done by U-Boot
persist even after the PHY is reset and taken over by Linux, and even
more unfortunate that Linux has come to depend on things being set in a
certain way.
For example, on the NXP LS1028A-RDB, the felix switch ports are
connected to a VSC8514 QSGMII PHY. Between the switch port PCS and the
PHY, the U-Boot drivers enable in-band auto-negotiation which makes the
copper-side negotiated speed and duplex be transmitted from the PHY to
the MAC automatically.
The PHY driver portion that does this is in vsc8514_config():
/* Enable Serdes Auto-negotiation */
phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS,
PHY_EXT_PAGE_ACCESS_EXTENDED3);
val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_MAC_SERDES_CON);
val = val | MIIM_VSC8574_MAC_SERDES_ANEG;
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_MAC_SERDES_CON, val);
The point is that in-band autoneg should be turned on in both the PHY
and the MAC, or off in both the PHY and the MAC, otherwise the QSGMII
link will be broken.
And because phy_config() is currently called at .port_enable() time, the
result is that ports on which traffic has been sent in U-Boot will have
in-band autoneg enabled, and the rest won't.
It can be argued that the Linux kernel should not assume one way or
another and just reinitialize everything according to what it expects,
and that is completely fair. In fact, I've already started an attempt to
remove this dependency, although admittedly I am making slow progress at
it:
https://patchwork.kernel.org/project/netdevbpf/cover/20210212172341.3489046-1-olteanv@gmail.com/
Nonetheless, the sad reality is that NXP also has, apart from kernel
drivers, some user space networking (DPDK), and for some reason, the
expectation there is that somebody else initializes the PHYs. The kernel
can't do it because the device ownership doesn't belong to the kernel,
so what remains is for the bootloader to do it (especially since other
drivers generally call phy_config() at probe time). This is a really
weak guarantee that might break at any time, but apparently that is
enough for some.
Since initializing the ports and PHYs at probe time does not break
anything, we can just do that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
No one is calling this function from outside felix_switch.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
Non DM builds fail with the following error:
drivers/net/tsec.c:641:24: error: 'tsec_get_interface' defined but not used [-Werror=unused-function]
641 | static phy_interface_t tsec_get_interface(struct tsec_private *priv)
Fix that.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
In commit b24bb99d cp110 configuration initially done in u-boot
was removed and delegated to atf firmware as smc call.
That commit didn't account for later introduced in d13b740c SATA invert polarity support.
This patch adds support of passing SATA invert polarity flags to atf
firmware during the smc call.
Signed-off-by: Denis Odintsov <shiva@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr
support").
Fixes: 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The KBUILD_BASENAME contains just the name of the compiled module,
in this case 'sequencer', rather than a full path to the compiled
file. Use it to prevent pulling the full path into the U-Boot binary,
which is useless and annoying.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
