Layerscape began to use two eSDHC controllers, for example,
LS1012A. They are same IP block with same reference clock.
This patch is to add clock support for the second eSDHC.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As per LS1046A hardware manual, SGMII.9 and SGMII.10 present on
lane D and lane C respectively for 0x3363 protocol.
So fix serdes1 settings for ls1046a.
Signed-off-by: Maciej Pijanowski <maciej.pijanowski@3mdeb.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Fixes a link error on layerscape platform, linking fails with CONFIG_PCI
set and CONFIG_PCI_LAYERSCAPE unset.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Change bootcmd update logic when CONFIG_ENV_ADDR is not defined
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Update qspi clock configuration in TFABOOT in case
of all boot sources except qspi boot source.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Flushing L3 cache may need variable time depending upon cache line
allocation.
Coming up with a proper timeout value would be best handled by
simulations under multiple scenarios in your actual system.
>From the purely HN-F point of view, the flush would take ~15 cycles for
a clean line, and ~22 cycles for a dirty line. For the dirty line case,
there are many variables outside the HN-F that will increase the
duration per line. For example, a *DBIDResp from the SN-F/SBSX,
memory controller latency, SN-F/SBSX RetryAck responses, CCN ring
congestion, CCN ring hops, etc, etc. The worst-case timeout would
have to factor in all of these variables plus the HN-F cycles for
every line in the L3, and assuming all lines are dirty
In case if L3 is not flushed properly, system behaviour will be
erratic, so remove timeout and add loop to check status of L3 cache.
System will stuck in while loop if there is some issue in L3 cache
flushing.
Signed-off-by: Udit Kumar <udit.kumar@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Layerscape began to use two eSDHC controllers, for example,
LS1028A. They are same IP block with same reference clock.
This patch is to add clock support for the second eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Rx Compliance tests may fail intermittently at high jitter
frequencies using default register values.
So program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable workaround for USB erratum A-008997. Here PCSTXSWINGFULL
registers has been moved to DSCR as compared to other Layerscape SoCs
where it was in SCFG.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
ENVL_NOWHERE is dependent on CONFIG_ENV_IS_NOWHERE and not on
CONFIG_CHAIN_OF_TRUST so return ENVL_NOWHERE when CONFIG_ENV_IS_NOWHERE
is enabled
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The LX2160A PCIe is using driver PCIE_LAYERSCAPE_GEN4 instead
of PCIE_LAYERSCAPE.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The lx2160a have up to 6 PCIe controllers and have different
address and size of PCIe region.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Change to use PCIe address macro to determine if precompile the PCIe
MMU table entry.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is fix to:
e2a12f590d rockchip: use 'arch-rockchip' as header file path
The V2 of origin patch set has fix this, but we merge V1 by
mistake, so lets correct it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
On AM654 SoC(arm64) which is IO coherent and has L3 Cache, cache
maintenance operations being done to support non-coherent platforms
causes issues.
For example, here is how U-Boot prepares/handles a buffer to receive
data from a device (DMA Write). This may vary slightly depending on the
driver framework:
Start DMA to write to destination buffer
Wait for DMA to be done (dma_receive()/dma_memcpy())
Invalidate destination buffer (invalidate_dcache_range())
Read from destination buffer
The invalidate after the DMA is needed in order to read latest data from
memory that’s updated by DMA write. Also, in case random prefetch has
pulled in buffer data during the “wait for DMA” before the DMA has
written to it. This works well for non-coherent architectures.
In case of coherent architecture with L3 cache, DMA write would directly
update L3 cache contents (assuming cacheline is present in L3) without
updating the DDR memory. So invalidate after “wait for DMA” in above
sequence would discard latest data and read will cause stale data to be
fetched from DDR. Therefore invalidate after “wait for DMA” is not
always correct on coherent architecture.
Therefore, provide a Kconfig option to disable cache maintenance ops on
coherent architectures. This has added benefit of improving the
performance of DMA transfers as we no longer need to invalidate/flush
individual cache lines(especially for buffer thats several KBs in size).
In order to facilitate use of same Kconfig across different
architecture, I have added the symbol to top level arch/Kconfig file.
Patch currently disables cache maintenance ops for arm64 only.
flush_dcache_all() and invalidate_dcache_all() are exclusively used
during enabling/disabling dcache and hence are not disabled.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
rockchip platform header file is in 'arch-rockchip'
instead of arch-$(SOC) for all SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This fixes relaction isses with the PSCI_TABLE entries in
the psci_32_table and psci_64_table.
When using 32-bit adress pointers relocation was not being applied to
the tables, causing PSCI handlers to point to the un-relocated code
area. By using 64-bit data relocation is properly applied. The
handlers are thus in the "secure data" area, which is protected by
/memreserve/ in the FDT.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
HVC call makes use of 6 mandatory arguments rather than 7 in the same way
as SMC calls. The 7th argument is optional (Client ID) for both HVC and
SMC but is implemented as 16-bit parameter and register R7 or W7. The aim
of this patch is just fix compilation error due to an invalid asm code in
the HVC call so that's why the 7th argument is removed.
The issue does not report any error in a normal build as hvc_call is not
used at all and is optimized by the compiler. Using -O0 triggers the
error so the patch is intended to fix issues on a ongoing effor to build
U-Boot with -O0.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
When PSCI is enabled, we are expecting U-Boot which now act
as EL3 software will handle all the PSCI calls. We won't need
fwcall as no further HVC or SMC are needed.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Allow PSCI layer to handle any SiP service functions added by
platform vendors. PSCI layer will look for SiP service function
in the SiP function table located in '._secure_svc_tbl_entries'
section if the SMC function identifier is not found in the PSCI
standard functions table. Use DECLARE_SECURE_SVC macro to declare
and add platform specific SiP service function.
This new section '._secure_svc_tbl_entries' is located next to
'._secure.text' section. Refer to arch/arm/cpu/armv8/u-boot.lds.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Commit 1416e2d225 ("armv8: make SPL exception vectors optional") had a
typo in it which effectively disabled exception handling in SPL code always.
Since nobody complained, I guess we may as well disable exception handling
in SPL always by default.
So fix the bug to make the config option effective, but disable exception
handling in SPL by default. This gets us to the same functionality as before
by default, but with much less code included in the binary.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The SEC QI ICID setup in the QIIC_LS register is actually an offset
that is being added to the ICID coming from the qman portal. Setting
it with a non-zero value breaks SMMU setup as the resulting ICID is
not known. On top of that, the SEC QI ICID must match the qman portal
ICIDs in order to share the isolation context.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
remove SCSI and SCSI_AHCI configs for ls1043ardb due to no sata interface
support.
this changed is to fixed the ls1043ardb compile warning as fallows:
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the
v2019.07 release. Failure to update by the deadline may
result in board removal.See doc/driver-model/MIGRATION.txt
for more info.
====================================================
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: reword the patch subject]
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Moves FSL_TZASC_400 and FSL_TZPC_BP147 configs to Kconfig
for LS1088A and LS2088A platforms.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
some dpmacs in armv8a based freescale layerscape SOCs can be
configured via both serdes(sgmii, xfi, xlaui etc) bits and via
EC*_PMUX(rgmii) bits in RCW.
e.g. dpmac 17 and 18 in LX2160A can be configured as SGMII from
serdes bits and as RGMII via EC1_PMUX/EC2_PMUX bits
Now if a dpmac is enabled by serdes bits then it takes precedence
over EC*_PMUX bits. i.e. in LX2160A if we select serdes protocol
that configures dpmac17 as SGMII and set the EC1_PMUX as RGMII,
then the dpmac is SGMII and not RGMII.
Therefore, move the fsl_rgmii_init after fsl_serdes_init. in
fsl_rgmii_init function of SOC, we will check if the dpmac is enabled
or not? if it is (fsl_serdes_init has already enabled the dpmac), then
don't enable it.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add code to initial ethernet interface arrays
with corresponding dpmac-id values in serdes_init function
for LX2160A.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Commit 81ea00838c ("efi_loader: PSCI reset and shutdown") put the SMCCC
assembly code into the efi specific code section. This is wrong when we
do not have EFI_LOADER enabled, as that strips efi runtime sections from
the output binary
Reported-by: Michal Simek <monstr@monstr.eu>
Reported-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Fixes: 81ea00838c ("efi_loader: PSCI reset and shutdown")
Signed-off-by: Alexander Graf <agraf@suse.de>
Refactor the switch from supervisor to hypervisor to a new function called
at the beginning of do_bootefi().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is hard dependency for CLK_ZYNQMP to have zynqmp_pmufw_version()
but also FPGA code is calling this function which is possible to use
without actual CLK_ZYNQMP firmware driver to be enabled.
This patch enables the case where only fixed-clock CLK setup is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On LS1043A rev1.0 there are 4 interrupt pins for INTx, and on
rev1.1 there is only 1 for INTx, so the current fixup is inverse
of the fact.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1043A/LS1023A 23x23 package silicon has different SVR:VAR_PER.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Fixes for TFABOOT framework
- update eMMC bootsrc to SD_MMC
- Increase buffer size for mcinitcmd from 256 to 512
- Fix mcinitcmd and bootcmd for Secure Boot
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add Kconfig option WATCHDOG_RESET_DISABLE to disable watchdog reset
in imx_watchdog driver, so that the watchdog will not be fed in
u-boot if CONFIG_WATCHDOG_RESET_DISABLE is enabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Support watchdog driver for fsl-lsch2. It's disabled in default.
If you want to use it, please enable CONFIG_IMX_WATCHDOG.
Define CONFIG_WATCHDOG_TIMEOUT_MSECS to set watchdog timeout.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
NXP layerscape architecture Chassis 3.2 builds upon chassis3
architecture with changes like DDR Memory map change,
removal of IFC and support of upto 8 I2C controller.
Patch add README.lsch3_2 and the above changes under
macro CONFIG_NXP_LSCH3_2.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some lsch3 based SoCs like lx2160a contains three
serdes modules.
Add support for third serdes protocol in lsch3
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support of MC framework for TFA
Make MC framework independent of boot source.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Returns job ring status as true in TFABOOT, as one job ring is always
reserved.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Changes the el2_to_aarch32 SMC ID from 0xc000ff04 to 0xc200ff17,
it is applicable to both TFA and non-TFA boot.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Workaround of erratum A010539 clears the RCW source field in PORSR1
register, causing failure of detecting boot source using this method.
Use SMC call if U-Boot runs at EL2. If SMC is not implemented or
running at EL3, continue to read PORSR1 and presume QSPI as boot
source if erratum workaround A010539 is enabled and RCW source is
cleared.
Signed-off-by: York Sun <york.sun@nxp.com>
OCRAM initialization is performed by TFA, Hence
skipped from u-boot.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds SMC calls for getting DDR size and bank info for TFABOOT.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Removes EL3 specific erratas for TFABOOT, And now taken care in TFA.
ARM_ERRATA_855873, SYS_FSL_ERRATUM_A008850, SYS_FSL_ERRATUM_A008511,
SYS_FSL_ERRATUM_A008336, SYS_FSL_ERRATUM_A009663,
SYS_FSL_ERRATUM_A009803, SYS_FSL_ERRATUM_A009942,
SYS_FSL_ERRATUM_A010165
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PORSR register holds the cfg_rcw_src field which can be used
to identify boot source.
Further, it can be used to select the environment location.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix multiple checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
Adds TFABOOT support config option and add generic code to enable
execution from DDR.
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Change tlb base address from OCRAM to DDR when exception level is
less than 3.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In case SError happens at EL2, if SCR_EL3[EA] is not routing it to
EL3, and SCR_EL3[RW] is set to aarch64, setting HCR_EL2[AMO] routes
the exception to EL2. Otherwise this exception is not taken.
Signed-off-by: York Sun <york.sun@nxp.com>
Move static definitions to cpu.c file, as it doesn't allow
the cpu.h file to be included in multiple c files.
Signed-off-by: York Sun <york.sun@nxp.com>
When an operating system started via bootefi tries to reset or power off
this is done by calling the EFI runtime ResetSystem(). On most ARMv8 system
the actual reset relies on PSCI. Depending on whether the PSCI firmware
resides the hypervisor (EL2) or in the secure monitor (EL3) either an HVC
or an SMC command has to be issued.
The current implementation always uses SMC. This results in crashes on
systems where the PSCI firmware is implemented in the hypervisor, e.g.
qemu-arm64_defconfig.
The logic to decide which call is needed based on the device tree is
already implemented in the PSCI firmware driver. During the EFI runtime
the device driver model is not available. But we can minimize code
duplication by merging the EFI runtime reset and poweroff code with
the PSCI firmware driver.
As the same HVC/SMC problem is also evident for the ARMv8 do_poweroff
and reset_misc routines let's move them into the same code module.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Allow platform vendors to handle SError interrupt exceptions from
ARMv8 PSCI exception vectors by overriding this weak function
'plat_error_handler'.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
This patch adds new zynqmp command "zynqmp tcminit mode" to
initialize TCM. TCM needs to be initialized before accessing
to avoid ECC errors. This new command helps to perform
the same. It also makes tcm_init() as global and uses it for
doing the TCM initialization.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves TCM initialization to a separate routine to
make it modular and can be reused if required. It also prints
warning message now as it writes to TCM.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XRFI
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
Reuse the existing ICID setup code done for LS1046A smmu enablement
and add the equivalent setup for LS1043A chips.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
At present the MMC subsystem maintains its own list of MMC devices.
This cannot work with driver model when CONFIG_BLK is enabled, use
blk_dread to replace previous mmc read interface, use
mmc_get_blk_desc to get the mmc device property.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Modify the zynqmp_pmufw_version() routine to return PMUFW version so
that it can be reused wherever required. Get PMUFW version from PMU
only once at bootup and later just return stored value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves the PM version related macros to .h file so that
they can be reused in other files.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use CONFIG_IS_ENABLED(EFI_LOADER) to avoid explicitly checking CONFIG_SPL
too. This simplifies the conditional.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Update README.falcon to use "none" for compression property for
ramdisk image to avoid being uncompressed upon loading.
Signed-off-by: York Sun <york.sun@nxp.com>
Program Central Security Unit (CSU) to grant access to USB 2.0
controller.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: rewrite commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for SEC ICID configuration and apply it for ls1046a.
Also add code to make the necessary device tree fixups.
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for ICID setting of fman ports and the required device
tree fixups.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for ICID setting of qman portals and the required device
tree fixups. Also fix an endiness issue in portal setup code.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add infrastructure for ICID setup and device tree fixup on ARM
platforms. This include basic ICID setup for several devices.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Even though the exception vector table is a fundamental part of the ARM
architecture, U-Boot mostly does not make real use of it, except when
crash dumping. But having it in takes up quite some space, partly due to
the architectural alignment requirement of 2KB. Since we don't take special
care of that, the compiler adds a more or less random amount of padding
space, which increases the image size quite a bit, especially for the SPL.
On a typical Allwinner build this is around 1.5KB of padding, plus 1KB
for the vector table (mostly padding space again), then some extra code
to do the actual handling. This amounts to almost 10% of the maximum image
size, which is quite a lot for a pure debugging feature.
Add a Kconfig symbol to allow the exception vector table to be left out
of the build for the SPL.
For now this is "default y" for everyone, but specific defconfigs,
platforms or .config files can opt out here at will, to mitigate the code
size pressure we see for some SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The arm64 exception handling code is quite big, mostly due to
architectural alignment requirements. Each exception entry spans 32
instructions, which sounds generous, but is too small to fit all of the
save/branch/restore code in there. So at the moment we use only four
instructions, branching into shared save and restore routines.
To not leave the space for those remaining 28 instructions wasted, let's
split the save and restore routines and stuff them into the gaps.
This saves about 250 bytes of code, which is helpful for those tight
SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ePTT
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
Another round of sorting Kconfig entries aplhabetically.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The include/phy.h will start including dm.h, which pulls in
linux/compat.h after the attempted redefinition in
arch/arm/include/asm/armv8/mmu.h, so move this include to allow
redefinition.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
A new defconfig is introduced to support SPL boot from QSPI NOR
flash. This is to support falcon mode for faster booting into
Linux.
Signed-off-by: York Sun <york.sun@nxp.com>
Remove the old implementation in order to enable DM for sata.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable I-cache for SPL boot to boost performance. Earlier MMU was
enabled only for LS2080A and has since been dropped by commit
f539c8a4a7 ("armv8: ls2080a: Drop early MMU for SPL build").
Signed-off-by: York Sun <york.sun@nxp.com>
Some times gcc may generate data that is then used within code that may
be part of an efi runtime section. That data could be jump tables,
constants or strings.
In order to make sure we catch these, we need to ensure that gcc emits
them into a section that we can relocate together with all the other
efi runtime bits. This only works if the -ffunction-sections and
-fdata-sections flags are passed and the efi runtime functions are
in a section that starts with ".text".
Up to now we had all efi runtime bits in sections that did not
interfere with the normal section naming scheme, but this forces
us to do so. Hence we need to move the efi_loader text/data/rodata
sections before the global *(.text*) catch-all section.
With this patch in place, we should hopefully have an easier time
to extend the efi runtime functionality in the future.
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf: Fix x86_64 breakage]
The Allwinner A64 SoCs suffers from an arch timer implementation erratum,
where sometimes the lower 11 bits of the counter value erroneously
become all 0's or all 1's [1]. This leads to sudden jumps, both forwards and
backwards, with the latter one often showing weird behaviour.
Port the workaround proposed for Linux to U-Boot and activate it for all
A64 boards.
This fixes crashes when accessing MMC devices (SD cards), caused by a
recent change to actually use the counter value for timeout checks.
Fixes: 5ff8e54888 ("sunxi: improve throughput
in the sunxi_mmc driver")
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-May/576886.html
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Tested-by: Guillaume Gardet <guillaume.gardet@free.fr>
At the moment we have the workaround for the Freescale arch timer
erratum A-008585 merged into the generic timer_read_counter() routine.
Split those two up, so that we can add other errata workaround more
easily. Also add an explaining comment on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Tested-by: Guillaume Gardet <guillaume.gardet@free.fr>
cpu_cmd() is reading cpu number via simple_strtoul() which is always
unsigned type.
Platform code implementations are not expecting that nr can be negative
and there is not checking in the code for that too.
This patch is using u32 type for cpu number to make sure that platform
code get proper value range.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There should be return value check from zynqmp_mmio_read() in
zynqmp_mmio_rawwrite() to make sure that errors are propagated properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We currently handle the UEFI runtime reset / power off case handling via
a switch statement. Compilers (gcc in my case) may opt to handle these via
jump tables which they may conveniently put into .rodata which is not part
of the runtime section, so it will be unreachable when executed.
Fix this by just converting the switch statement into an if/else statement.
It produces smaller code that is faster and also correct because we no
longer refer .rodata from efi runtime code.
Reported-by: Andreas Färber <aferber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
PPA firmware and header address may vary depending upon different
boards, configure ppa firmware and header address in board specific
Kconfig.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Existing EEMI version is to as 1.0 (available from xilinx v2018.1
version). Update required API version to match with EEMI API version.
New PMUFW version is required for operations with programmable logic.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP emulation platforms are no longer tested and supported that's why
remove macros and code around.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlr1ldMACgkQykllyylKDCHioACghoJw6+NqsZXl8zGWRP38yZ5K
mvgAnihfOQq125mpKPZmcc5yt6wVwYIU
=8ji9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.07
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
This patch fills the MMU map for DDR at run time based on information read
from Device Tree or automatically detected from static configuration.
The patch is needed because for systems which has for example 1GB of memory
but MMU map is 2GB there could be spurious accesses which was seen in past
when mapping is not fitting with actual memory installed.
Signed-off-by: Nitin Jain <nitin.jain@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mask HRESET_B after cleared the the RCW_SRC, because in the workaround
we override the RCW_SRC and if HRESET_B is issued after the override
then SoC cannot find valid RCW as the RCW_SRC was overwritten and
result in hang. So we need to mask HRESET_B in case user asserts it,
and the PORESET_B should be asserted which leads to resampling of
cfg_rcw_src pins and loading of correct RCW_SRC.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable support for multiple loadable images in SEC firmware FIT image.
Also add example "sec_firmware_ppa.its" file.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
JR3 was getting removed from device tree only if random number
generation was successful. However, if SEC firmware is present,
JR3 should be removed from device tree node irrespective of the
random seed generation as SEC firmware reserves it for it's use.
Not removing it in case of random number generation failure causes
the kernel to crash.
Random number generation was being called twice. This is not
required. If SEC firmware is running, SIP call can be made to the SEC
firmware to get the random number. This call itself would return
failure if function is not supported. Duplicate calling of random
number generation function has been removed.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TZASC controller configurations are similar. Put them in a macro and
avoid code duplication.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
SYS_ARCH_TIMER guards the usage of the ARM Generic Timer (aka arch
timer) in U-Boot.
At the moment it is mandatory for ARMv8 and used by a few ARMv7 boards.
Add a proper Kconfig symbol to express this dependency properly,
allowing certain board configuration to later disable arch timer in case
there are any problems with it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[tuomas: rebase + fix conflicts and resync with moveconfig & use select]
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The default of DISTRO_DEFAULTS is messy. Using the 'imply' keyword
is equivalent and cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
EFI_RESET_PLATFORM_SPECIFIC is one of the values that can be used for the
EFI service ResetSystem. The missing definition is added. The value has to
handled in efi_reset_system().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_reset_system_init provides the architecture or board specific
initialization of the EFI subsystem. Errors should be caught and
signalled by a return code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
NXP layerscape platforms like ls1088a, ls2088a
uses MXC I2C Controller.
-Remove dependency of MX6 for the same.
Update related configs to use Kconfig file.
-Add SYS_I2C_MXC_I2C1,_I2C2,_I2C3,_I2C4 in Kconfig
-Add CONFIG_SYS_MXC_I2C1_SPEED,_I2C2_,_I2C3_,_I2C4_ in Kconfig
-Add CONFIG_SYS_MXC_I2C1_SLAVE,_I2C2_,_I2C3_,_I2C4_ in Kconfig
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
As of now newer pmufw is keeping old interfaces. That's why permit
u-boot to run on newer version. Recommended version will be setup later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
1. Set AWCACHE0 attribute of PFE DDR and HDBUS master interfaces
to bufferable.
2. Set RD/WR QoS for PFE DDR and HDBUS AXI master interfaces.
3. Disable ECC detection for PFE.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove dependency of SYS_HAS_SERDES for Layerscape Chasis 2 and
Layerscape Chasis 3.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The goal of this patch is to clean up the code related to choosing SPL
MMC boot mode.
The spl_boot_mode() now is called only in spl_mmc_load_image() function,
which is only compiled in if CONFIG_SPL_MMC_SUPPORT is enabled.
To achieve the goal, all per mach/arch implementations eligible for
unification has been replaced with one __weak implementation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com> (For ZynqMP)
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
There is no JTAG symbol in the "Boot mode" choice. JTAG_MODE was
probably intended.
No functional changes. Kconfig choices fall back on using the first
(visible) symbol in the choice as the default if the default symbol is
not visible.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection JTAG (undefined) of <choice> (defined at arch/arm/cpu/armv8/zynqmp/Kconfig:107) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move generic functions to common location psu_spl_init.c. Function
declarations are added to private header.
These changes are done in connection to the fact that still files from
HDF can be copied over and compilation should pass.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DDR less systems are possible for configuration like mini qspi
and making DDR region as normal memory may cause speculative
access which results u-boot hang if DDR is absent. So, this
patch fixes the issue by not making DDR memory region
entry into MMU table.
Future solution is to prepare MMU table per memory node in dts instead
of hard code DDR addresses.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psu_init() returns int which wasn't declared and checked.
The patch is fixing function declarations and code to handle return
values properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set the 8GB PCIe High area as device memory.
Also extend the DDR High area to cover the full 32GB range.
Signed-off-by: Anders Hedlund <anders.j.hedlund@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adds a VID specific API in init_sequence_f and spl code flow
namely init_func_vid which is required to adjust core voltage.
VID specific code is required in spl, hence moving flag CONFIG_VID
out of spl flags.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds SERDES voltage and reset SERDES lanes API and makes
enable/disable DDR controller support 0.9V API common.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Remove the unit address from the config node name when U-Boot deals with
secure firmware FIT images.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Fix all occurences in various documentation files where this was not
observed, to not give bad examples to the reader.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The SP805-WDT module on LS1088A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Align boards belonging to LS1012A, LS2080A SoC at one place.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Allow placing a Linux kernel image header at the start of the U-Boot
binary. This is useful since the image header reports the amount of memory
(BSS and similar) that U-Boot needs to use, but that isn't part of the
binary size. This can be used by the code that loads U-Boot into memory to
determine where to load U-Boot, based on other users of memory.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Compile-off mp.c and libfdt.c in case of SPL build. SPL size reduces
by approx 2k.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
855873: An eviction might overtake a cache clean operation
Workaround: The erratum can be avoided by upgrading cache clean by
address operations to cache clean and invalidate operations. For
Cortex-A53 r0p3 and later release, this can be achieved by setting
CPUACTLR.ENDCCASCI to 1.
This patch is to implement the workaround for this erratum.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware
- Create new board/freescale/common/fsl_portals.c to house shared
device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
setup to disable interrupts on all QMan and BMan portals. It is
needed because the interrupts are enabled by default for all portals
including unused/uninitialised portals. When the kernel attempts to
go to deep sleep the unused portals prevent it from doing so
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sata registers PP2C and PP3C are used to control the configuration
of the PHY control OOB timing for the COMINIT/COMWAKE parameters
respectively. Calculate those parameters from port clock frequency.
Overwrite those registers with calculated values to get better OOB
timing.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using "cpu_pos_mask()" function to detect the real online cpus,
and discard the needless cpu nodes on kernel dts.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Check LS1043A/LS2080a by device ID without using personality ID to
determine revision number. This check applies to all various
personalities of the same SoC family.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Validates PPA, MC, DPC, Bootscript, DPL and Kernel images in ESBC
phase using esbc_validate command.
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment
Add header address for PPA to be validated during ESBC phase for
LS1088A platform based on LAyerscape Chasis 3.
Moves sec_init prior to ppa_init as for validation of PPA sec must
be initialised before the PPA is initialised.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This is suplement for patch which handle below errata:
A-009007, A-009008, A-008997, A-009798
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Instruction prefetch feature is by default enabled during core
release. This patch add support of disabling instruction prefetch
by setting core mask in PPA. Here each core mask bit represents a
core and prefetch is disabled at the time of core release.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To page mapping the lowest 2 bits needs to be 0x3.
If not fix this, the final lowest 3 bits for page mapping is 0x1
which is marked as reserved.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In the moment our exception entry code needs 34 instructions, so we
can't use put it directly into the table entry, which offers "only"
32 instructions there. Right now we just put an unconditional branch
there, then use a macro to place the 34 instructions *per entry* after
that. That effectivly doubles the size of our exception table, which
is quite a waste, given that we use it mostly for debugging purposes.
Since the register saving part is actually identical, let's just convert
that macro into a function, and "bl" into it directly from the exception
slot, of course after having saved at least the original LR.
This saves us about 950 bytes of code, which is quite a relief for some
tight SPLs, in particular the 64-bit Allwinner ones.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This modifies default value of config DEFINE_TCM_OCM_MMAP
to yes if CONFIG_MP is defined MP supports needs OCM and TCM
part of memory map.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch is adding external pmufw "Platform Management Unit firmware"
to boot.bin image. Boot.bin is a Xilinx format which bootrom is capable
to read and boot the system. pmufw is copied to the header data section
follows by u-boot-spl.bin. pmufw is consumed by PMU unit (Microblaze)
and SPL runs on a53-0.
This is generated command line when PMUFW_INIT_FILE is setup.
./tools/mkimage -T zynqmpimage -R ./"" -n
./"board/xilinx/zynqmp/pmufw.bin" -d spl/u-boot-spl.bin spl/boot.bin
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch provides a Kconfig option to use specified
memory for MMU table using reserve_mmu platform specific
routine. Here we used TCM space for MMU table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch corrects the R5 release sequence by adding the
below steps.
1. Flush dcache to ensure that image loaded into memory.
2. Keep R5 reset just to ensure R5 in reset.
3. Disable caches before accessing TCM as with out this
A53 can do speculative and may result in ECC failures
if TCM's are not initialized. So, it is always better
to disable dcaches before accessing TCM and enable back.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In
if (a || b)
else if (!a)
the constraint (!a) is always true if else is reached and
can be removed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base
in simple_strtoul.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable support for loadables in SEC firmware FIT image. Currently
support is added for single loadable image.
Brief description of implementation:
Add two more address pointers (loadable_h, loadable_l) as arguments to
sec_firmware_init() api.
Create new api: sec_firmware_checks_copy_loadable() to check if loadables
node is present in SEC firmware FIT image. If present, verify loadable
image and copies it to secure DDR memory.
Populate address pointers with secure DDR memory addresses where loadable
is copied.
Example use-case could be trusted OS (tee.bin) as loadables node in SEC
firmware FIT image.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use Kconfig to select QE-HDLC and USB pin-mux.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add jump_to_image_linux() for arm64. Add "noreturn" flag to
armv8_switch_to_el2(). Add hooks to fsl-layerscape to enable falcon
boot.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Tested-by: Łukasz Majewski <lukma@denx.de>
gd->ram_size is reduced in this function to reserve secure memory.
Avoid running this function again to further reduce memory size.
This fixes issue for SPL boot with PPA image loaded in which case
secure memory is incorrectly allocated due to repeated calling.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 15eb1d43bf ("spl: reorder the assignment of board info to
global data") intended to move assignment of board info earlier,
into board_init_r(). However, function preload_console_init() is
called either from spl_board_init() or from board_init_f(). For the
latter case, the board info assignment is much earlier than proposed
board_init_r(). Create a new function to fill gd->bd and call this
function when needed.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Ravi Babu <ravibabu@ti.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change is required due to trusted OS (OP-TEE) not being position
independent code, it requires compile time fixed base address.
To take care of this it is assumed that all layerscape armv8 platforms
has minimum 2G ddr in first region. So we can have fixed address
space (66 MB -> (2MB for PPA + 64MB for trusted OS)) allocated from
top of first 2G ddr region and compile trusted OS with this fixed
base address.
But one exception here is ls1012 where we have only 1G (rdb) or 512M
(frdm) ddr memory. For those we can have different fixed compile time
base addresses for trusted OS.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Rx Compliance tests may fail intermittently at high jitter
frequencies using default register values.
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is not necessary for every SoC to have 2 SATA controller.
So put SATA1, SATA2 code under respective defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
All these places seem to inherit the codes from the MMC driver where
a FIXME was put in the comment. However the correct operation after
read should be cache invalidate, not flush.
The underlying drivers should be responsible for the cache operation.
Remove these codes completely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: York Sun <york.sun@nxp.com>
CCN-504 HPF registers were believed to be accessible only from EL3.
However, recent tests proved otherwise. Remove checking for exception
level to re-enable L3 cache flushing for all levels.
Signed-off-by: York Sun <york.sun@nxp.com>
Tested-by: Zhao Qiang <qiang.zhao@nxp.com>
In case high region memory doesn't have enough space for Management
Complex (MC), the return value should indicate a failure so the
caller can handle it accordingly.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Ebony Zhu <ebony.zhu@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter
settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for RGMII protocol
NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
According current code base, CONFIG_LS1012A should be
CONFIG_ARCH_LS1012A, or function fsl_fdt_disable(blob) will be
wrongly called to disable all dwc3 USB nodes on LS1012A, which
cause Linux USB function stop working at all.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080 family has CCN-504 cache coherent interconnet. Other SoCs
in LSCH3 family may have differnt interconnect.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Unify memory map for Layerscape based platforms. This patch includes
changes in bootscript, bootscript header and PPA header addresses
change as per unified memory map.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.
This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
kASLR support in kernel requires a random number to be passed via
chosen/kaslr-seed propert. sec_firmware generates this random seed
which can then be passed in the device tree node.
sec_firmware reserves JR3 for it's own usage. Node for JR3 is
removed from device-tree.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.
As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig. Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To fully support DM timer in SPL and TPL, we need a few things cleaned
up and normalised:
- inclusion of the uclass and drivers should be an all-or-nothing
decision for each stage and under control of $(SPL_TPL_)TIMER
instead of having the two-level configuration with TIMER and
$(SPL_TPL_)TIMER_SUPPORT
- when $(SPL_TPL_)TIMER is enabled, the ARMv8 generic timer code can
not be compiled in
This normalises configuration to $(SPL_TPL_)TIMER and moves the config
options to drivers/timer/Kconfig (and cleans up the collateral damage
to some defconfigs that had SPL_TIMER_SUPPORT enabled).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
TPL builds today don't need to call into firmware or set up the MMU
(if this changes, it should be controlled through a config option
whether to include this or not), but include the needed support code
for this anyway. By moving these unused low-level functions into
seperate function-sections, the linker can garbage-collect the unused
sections.
Note that (if DM support is enabled), there will be a call to the
cache-flushing code from alloc_priv(...) in drivers/core/device.c.
This then add 52 bytes of binary size (an increase from 20589 to 20641
bytes) compared to completely removing this code.
Even for a feature-rich TPL (including DM support as for the RK3368),
this equates to a size difference of significantly more than 10% in
TPL binary size.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_PCI
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
It is derived from Platform clock instead of Platform PLL frequency.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There is a need to include psu_init also in mini u-boot configuration
that's why handle psu_init via Kconfig property.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For some mini platforms there could be a need to include psu_init.
That's why move it to board file instead of spl only file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch removes ifdef around mmio read and write rotuines
and make them a single routine by checking the current el.
This patch helps to remove ifdef around invoke_smc as well.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
TCM on ZynqMP needs to be intialized in a sequence
and this patch provides a global routine to perform
this as per requirement.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch provides an option to include OCM and TCM memory
into MMU table with corresponding memory attributes.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The duplicate definitions for IH_ARCH_ARM and IH_ARCH_ARM64 are removed.
The definitions in <image.h> are used.
According to this modification, the comparison between os arch and cpu
arch is done in C programming instead of ASM programming.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, add a
function comment and adjust callers to use a boolean.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This actually works on snapdragon.. not sure why we weren't using it.
Fixes reboot/poweroff when using UEFI.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
If PMUFW version is not v0.3 then panic.
ZynqMP switch to CCF based clock driver which requires
PMUFW to be present at certain version.
This patch ensure that you use correct and tested PMUFW
binary.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define routines of mmio write and read functionalities
for zynqmp platform.
Also do not call SMC from SPL because SPL is running before ATF in EL3
that's why SMCs can't be called because there is nothing to call.
zynqmp_mmio*() are doing direct read/write accesses and this patch does
the same. PMUFW is up and running at this time and there is a way to talk
to pmufw via IPI but there is no reason to implement IPI stuff in SPL if
we need just simple read for getting clock driver to work.
Also make invoke_smc as global so that it can be reused in
multile places where ever possible.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Silicon v1 didn't support SD boot mode with level shifter.
Because system can't boot any error message is not shown
that's why comment is just a record if someone tries to debug it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The boot_device argument to spl_boot_mode was massively added without
actually modifying the existing functions.
This commit actually makes use of the handed value, which is the same.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When enabling both SDHCI controllers, spl_mmc.c would actually choose
device sdhci0 even if booted from sdhci1 (boot_device). This is because
spl_mmc_get_device_index(boot_device) expects BOOT_DEVICE_MMC2[_2] in
order to return index 1 instead of 0.
The #if defined(...) statement is copied from board/xilinx/zynqmp/zynqmp.c
So the key to properly enabling both controllers as boot sources is
defining both CONFIG_ZYNQ_SDHCI0 and CONFIG_ZYNQ_SDHCI1 in your board's
include/configs/*.h.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mark explicitly bss sections to not be loaded at
run time.
The similar patch was done in past by:
"Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections"
(sha1: 64134f0112)
The problem is related to latest toolchain added to Xilinx
v2017.1 design tools where jtag loader is trying to access
ununitialized memory.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for calling poweroff in case of psci is wired.
Based on the same solution as is used for reset.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move all logic in to fwcall.c as other ARMs implement poweroff
via PMIC]
Signed-off-by: Tom Rini <trini@konsulko.com>
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
Loading PPA in SPL puts the rest of U-Boot (including RAM version
loaded later) in EL2 with MMU and cache enabled. Once PPA is loaded,
PSCI is available.
Signed-off-by: York Sun <york.sun@nxp.com>
When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carried out before U-Boot runs. This applies
to the RAM version image used for SPL boot if PPA is loaded first.
Signed-off-by: York Sun <york.sun@nxp.com>
Add CONFIG_NAND_BOOT config flag to organise
NAND_BOOT specific code in config flag like
-nand-boot specfic errata errata_rcw_src()
-CONFIG_SYS_NAND_U_BOOT_DST,etc
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
These two functions have an of_ prefix which conflicts with naming used
in of_addr. Rename them:
fdt_read_number
fdt_support_bus_default_count_cells
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address
on serial flash and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS2081A SoC has eight 64-bit ARM v8 Cortex A72 cores and
is built on layerscape architecture. It is 40-pin derivative of
LS2084A (non-AIOP personality of LS2088A). So feature-wise it is
same as LS2084A. LS2041A is a 4-core personality of LS2081A.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The SMPEN bit is located in the cpuectlr_el1 register and not the
cpuactlr_el1 register. Adjust the comment accordingly and also fix
a spelling error.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
CC: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
CC: York Sun <york.sun@nxp.com>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
At present there is not operation to invalidate a cache range. This seems
to be needed to fill out the cache operations. Add an implementation based
on the flush operation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
PSCI can be used on both multiple and single core socs. Current
implementation only allows PSCI to work on multiple core socs.
This patch removes this restriction so that PSCI can work on
single core socs as well.
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add Kconfig option to support loading PPA header from eMMC/SD and
NAND Flash.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:
[Linux] [U-Boot]
arch/arm/kernel/smccc-call.S -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes* -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h -> include/linux/arm-smccc.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Current sysclk fixing would fix all clocks with 'fixed-clock' compatible.
This patch is to fix sysclk by path to avoid any incorrect fixing.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Number of TZASC instances may vary across NXP SoCs.
So put TZASC configuration under instance specific defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Define bootscript and its header addresses for QSPI target
Also add PPA header address in Kconfig
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The header address of PPA defined in Kconfig.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.
Signed-off-by: Simon Glass <sjg@chromium.org>
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
USB requires 100MHz clock. On LS1012A, a dedicated 100MHz is provided
instead of SYSCLK (125MHz). Skipping checking SYSCLK for FDT fixup.
Signed-off-by: Yingxi Yu <yingxi.yu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS2088A series SoCs has different physical memory map address and
CCSR registers address against LS2080A series SoCs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This i2c errata only applies to LS2080A and its variants, namely
LS2080A, LS2085A and LS2088A.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SerDes information is not necessary to be present in RCWSR29 register.
It may vary from SoC to SoC.
So Avoid RCWSR28 register hard-coding.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A009635 is valid only for LS2080A SoC and its
personality. Add SoC svr check.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Read DMA operations causes CRC error on armv8 chassis 2 platforms
due to the erratum A-010635.
In order to support sata on these platforms, ECC needs to be disabled.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.
Signed-off-by: York Sun <york.sun@nxp.com>
Function mmu_change_region_attr() is added to change existing mapping
with updated PXN, UXN and memory type. This is a break-before-make
process during which the mapping becomes fault (invalid) before final
attributres are set.
Signed-off-by: York Sun <york.sun@nxp.com>
Early MMU improves performance especially on emulators. However, the
early MMU is left enabled after the first stage of SPL boot. Instead
of flushing D-cache and dealing with re-enabling MMU for the second
stage U-Boot, disabling it for SPL build simplifies the process. The
performance penalty is unnoticeable on the real hardware. As of now,
SPL boot is not supported by existing emulators. So this should have
no impact on emulators.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch follows the break-before-make process when making changes
to MMU table. MMU is disabled before changing TTBR to avoid any
potential race condition.
Signed-off-by: York Sun <york.sun@nxp.com>
Update mapping with actual DDR size. Non-existing memory should not
be mapped as "normal" memory to avoid speculative access.
Signed-off-by: York Sun <york.sun@nxp.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config. We now just select these once at the higher level in Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP output clock.
Update sys_info->freq_localbus to represent IFC input clock with
value constant divisor of platform clock.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This feature seems to be sometimes misunderstood. The intention is:
[1] Bring the slaves into the U-Boot proper image, not SPL (unless
you have a special reason to do otherwise).
[2] The operation must be done in a board (SoC) specific manner
since how to wake the slaves from the Boot ROM is SoC specific.
[3] The slaves must enter U-Boot proper after U-Boot relocates
itself because the "cpu-release-addr" property points to the
relocated memory area.
[2] is already explained in the help. We can make [1] even clearer
by mentioning "U-Boot proper" instead of "U-Boot". [3] is missing,
so I am adding it to the list. Instead, "before the master CPU
jumps to the kernel" is a matter of course, so removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Moved the config FSL_PPA_ARMV8_PSCI from fsl-layerscape's Kconfig to
Kconfig under armv8 and renamed it to SEC_FIRMWARE_ARMV8_PSCI.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For 64-bit kernel, there is a warning about x1-x3 nonzero in violation
of boot protocol. To fix this issue, input argument 4 is added for
armv8_switch_to_el2 and armv8_switch_to_el1. The input argument 4 will
be set to the right value, such as zero.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The default MSI node in kernel tree is for LS1043A rev1.0 silicon, if
rev1.1 silicon used, need to fixup the MSI node to match it.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS1043A rev1.1 silicon supports two types of GIC offset: 4K
alignment and 64K alignment. The bit SCFG_GIC400_ALIGN[GIC_ADDR_BIT]
is used to choose which offset will be used.
The LS1043A rev1.0 silicon only supports the CIG offset with 4K
alignment.
If GIC_ADDR_BIT bit is set, 4K alignment is used, or else 64K alignment
is used. 64K alignment is the default setting.
Overriding the weak smp_kick_all_cpus, the new impletment is able to
detect GIC offset.
The default GIC offset in kernel device tree is using 4K alignment, it
need to be fixed if 64K alignment is detected.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
By default the SATA IP on the ls208Xa SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc register.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Set up chip power supply voltage according to voltage ID.
The fuse status register provides the values from on-chip
voltage ID fuses programmed at the factory. These values
define the voltage requirements for the chip.
Main operations:
1. Set up the core voltage
2. Set up the SERDES voltage and reset SERDES lanes
3. Enable/disable DDR controller support 0.9V if needed
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Without a prompt in Kconfig, SECURE_BOOT cannot be selected by
defconfig. The option was dropped unintentionally when defconfig
files were cleaned up. Three targets were impacted
ls1043ardb_SECURE_BOOT, ls2080ardb_SECURE_BOOT,
ls2080aqds_SECURE_BOOT.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch binds the sys_info->freq_systembus to Platform PLL, and
implements the IPs' clock function individually.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Up to now, there are 3 kind of SoCs under Layerscape Chassis 2,
like LS1043A, LS1046A and LS1012A. But the clocks tree has a
lot of differences, for instance, the IP modules have different
dividers to derive its clock from Platform PLL. And the core
cluster PLL and platform PLL maybe have different reference
clocks, such as LS1012A. Another problem is which clock/PLL
should be described by sys_info->freq_systembus, it is confused
in Layerscape Chissis 2.
This patch is to bind the sys_info->freq_systembus to the Platform
PLL, and handle the different divider of IP modules separately
between different SoCs, and separate reference clocks of core
cluster PLL and platform PLL.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For A53, data coherency is enabled only when the CPUECTLR.SMPEN bit is
set. The SMPEN bit should be set before enabling the data cache.
If not enabled, the cache is not coherent with other cores and
data corruption could occur.
For A57/A72, SMPEN bit enables the processor to receive instruction
cache and TLB maintenance operations broadcast from other processors
in the cluster. This bit should be set before enabling the caches and
MMU, or performing any cache and TLB maintenance operations.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Clear the content to zero and the ECC error bit of OCRAM1/2.
The OCRAM must be initialized to ZERO by the unit of 8-Byte before
accessing it, or else it will generate ECC error. And the IBR has
accessed the OCRAM before this initialization, so the ECC error
status bit should to be cleared.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is recommended to set forced-order mode in RNI-6,
RNI-20 for performance optimization in LS2088A.
Both LS2080A, LS2088A families has CONFIG_LS2080A define.
As above update is required only for LS2088A, skip this
for LS2080A SoC family.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using CONFIG_IS_ENABLED() doesn't work in SPL. This patch replaces the only
occurrence of CONFIG_IS_ENABLED() in start.S to a regular #if defined().
It also adds "&& !defined(CONFIG_SPL_BUILD)" to that #if statement because
the spin-table code can't currently work in SPL, and the spin-table file
isn't even compiled in SPL.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Xilinx ATF extending options for passing images from BL2(FSBL)
to BL31. U-Boot SPL is FSBL replacement that's why it should generate
handoff structure the same. Support only one entry which is U-Boot in
EL2 itself. When FIT image is adopted structure generate should be data
driven.
Currently ATF is placing this structure at the beggining of OCM which is
rewriting early parts of ATF which should be unused at that time.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a string description for SYS_VENDOR to allow configuring boards from
other vendors than just "xilinx".
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
Signed-off-by: York Sun <york.sun@nxp.com>
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <york.sun@nxp.com>
For prepending some board specific header area to U-Boot images we
were so far including a header file with a macro definition containing
the actual header specification.
This works fine if there are just a few statements and if there is only
one alternative.
However adding more complex code quickly gets messy with this approach,
so let's just drop that intermediate macro and let the #include actually
insert the code directly.
This converts the callers and the callees, but doesn't change anything
at this point.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The boot0 hook we have so far is applied _after_ the initial branch
to the "reset" entry point. An upcoming change requires even this
branch to be changed, so we apply the hook macro at the earliest
point, and have the branch in the hook file as well.
This is no functional change at this point, just refactoring to simplify
upcoming patches.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunxi DRAM setup code needs an sdelay() implementation, which
wasn't defined for armv8 so far.
Shamelessly copy the armv7 version and adjust it to work in AArch64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For boards that call s_init() when the SPL runs, we are expected to
setup an early stack before calling this C function.
Implement the proper AArch64 version of this based on the ARMv7 code.
This allows sunxi boards to setup the basic peripherals even with a
64-bit SPL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
A most basic PSCI implementation with only one psci_version is added for
LS1043A, this can verify the generic PSCI framework, and more platform specific
implementation will be added later.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Newly add ARMv8 PSCI needs to be initialized, be copied or reserved in right
place, this patch does all the setup steps.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch introduces a generic ARMv8 PSCI framework, with all functions
returning a dummy ARM_PSCI_RET_NI (Not Implemented), then it is up to each
platform to implement their own functions based on this framework.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds secure_text, secure_data and secure_stack sections for ARMv8 to
hold PSCI text and data, and it is based on the legacy implementation of ARMv7.
ARMV8_SECURE_BASE defines the address for PSCI secure sections, ARMV8_PSCI and
ARMV8_PSCI_NR_CPUS are firstly used in this patch, so they are introduce here
in Kconfig too.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP/Freescale uses macro CONFIG_ARMV8_PSCI to enable their private PSCI
implementation in PPA firmware, but this macro naming too generic, so this
patch replaces it with a specic one CONFIG_FSL_PPA_ARMV8_PSCI.
And this macro CONFIG_ARMV8_PSCI will be used for a generic PSCI for ARMv8
which will be added in following patchs.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The default configuration for QSPI AHB bus can't support 16MB+.
But some flash on NXP layerscape board are more than 16MB.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>
Using alternative bootmode field to support automatic secondary boot
modes. It is purely software setting where SW modes are using free
bootmode combinations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP provides an option to overwrite bootmode setting which
can change SPL behavior.
For example: boot SPL via JTAG and then SPL loads images from SD.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As PSCI and secure monitor firmware framework are enabled, this patch is
to support loading 32-bit OS in such case. The default target exception
level returned to U-Boot is EL2, so the corresponding work to switch to
AArch32 EL2 and jump to 32-bit OS are done in U-Boot and secure firmware
together.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Spin-table method is used for secondary cores to load 32-bit OS. The
architecture information will be got through checking FIT image and
saved in the os_arch element of spin-table, then the secondary cores
will check os_arch and jump to 32-bit OS or 64-bit OS automatically.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To support loading a 32-bit OS, the execution state will change from
AArch64 to AArch32 when jumping to kernel.
The architecture information will be got through checking FIT image,
then U-Boot will load 32-bit OS or 64-bit OS automatically.
Signed-off-by: Ebony Zhu <ebony.zhu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP ARMv8 SoC LS2080A release all secondary cores in one-go.
But other new SoCs like LS2088A, LS1088A release secondary
cores one by one.
Update code to release secondary cores based on SoC SVR
Add code to release cores one by one for non LS2080A SoCs
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: remove "inline" from declaration of initiator_type]
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS2088A SoC is built on layerscape architecture.
It is similar to LS2080A SoC with some differences like
1)Timer controller offset is different
2)It has A72 cores
3)It supports TZASC module
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080 SoC and its personalities does not support TZASC
But other new SoCs like LS2088A, LS1088A supports TZASC
Hence, skip initializing TZASC for Ls2080A based on SVR
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TZASC registers like TZASC_GATE_KEEPER, TZASC_REGION_ATTRIBUTES
are 32-bit regsiters.
So while doing register load-store operations, 32-bit intermediate
register, w0 should be used.
Update x0 register to w0 register type.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Timer controller base address has been changed from
LS2080A SoC (and its personalities) to new SoCs like
LS2088A, LS1088A.
Use SVR based timer base address detection to avoid compile time #ifdef.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update CONFIG_LS2080A to CONFIG_FSL_LSCH3 to make those workaround
implementing of erratum reusable for more SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJYLa6qAAoJECszeR4D/txgF+4QAKpHJXY/1V+McEsLga2iwePZ
lZu5NuuLeDA9IMH+ufOOGxDIoc/llZCTsqw5l8Vnkaz0JEH6v9svyEy4zC1Nqtj2
r4pOhGLAyVlGAh4O3hFFi/eHNEDyTrMoPO6JCy8ce+fEGE21VBlWed0+/c/KdV7F
85joTg3X+6htFMkLybzKZS1yiJyoROe7zUZdzPrn4ogwDGbazmYbED+P2u09dDzB
WjlpIbmEDWJEska6Cbgl/ee6dBXSVl8Q/SY3V77T5TB554sZozrKDsNUehiUMEbh
ggCT5VzPhsm4gb/7RBpTqqCabBT5ml8iKfB8Y7fwL43sDiMXJ1LgJyVnHuz65sCS
aPPsPjQujBSiqr+k/571yhgFNLVydrs9IYNumZr+Li4UZCvx3xtCjACJVYkbLUd1
SZrpKts0V45nZcE4IoiwDKOUxavUbLEef2SJTOAOppB3DG9L3O0TWkyH00hTkaxR
oDIVNSZPt9wSd4Q7FQ2MYxQ/sk+B6PrN6Gm/NMSfCnvP8DkyTzHo514qrWnEjlhQ
ndVmyJh3hpipNDfFDeF6r5lLtPkTrzNxOVZcsUGQC5jvrvwLWguD+Kuv9Qq4gSDp
uDawZmRwDGEGpR/yJhqj8r6/e7bZ0fOE6nPqbWLlyF+Oc4yFTz+D2CNPGR4CR0iF
DFGQN/lNkYbu+HfyZOFO
=xmR3
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2016-11-17
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
When implementing efi loader support, we can expose runtime services
for payloads. One such service is CPU reset.
This patch implements RTS CPU reset support for layerscape systems.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
The efi loader code has its own memory map, so it needs to be aware where
the spin tables are located, to ensure that no code writes into those
regions.
Signed-off-by: Alexander Graf <agraf@suse.de>
The NXP ls1043 and ls1046 systems do not (yet) have PSCI enablement
for reset. Don't enable generic PSCI reset code on them.
Signed-off-by: Alexander Graf <agraf@suse.de>
Do not setup use_alt bit which copy alternative boot mode to
boot mode. The reason is that this bit is cleared after POR
but not after any software reset which will cause
that after SW reset bootrom will look for different boot image.
This patch setups alternative boot mode selection (purely SW
handling) and extends code to read this alternative boot mode first and
use it if it is setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Zynq/ZynqMP boot.bin file contains a region for register initialization
data. Filling in proper values in this table can reduce boot time
(e.g. about 50ms faster on QSPI boot) and also reduce the size of
the SPL binary.
The table is a simple text file with register+data on each line. Other
lines are simply skipped. The file can be passed to mkimage using the
"-R" parameter.
It is recommended to add reg init file to board folder.
For example:
CONFIG_BOOT_INIT_FILE="board/xilinx/zynqmp/xilinx_zynqmp_zcu102/reg.int
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for EFI apps on aarch64. This includes start-up and relocation
code plus a link script.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agraf: add kconfig dep]
Signed-off-by: Alexander Graf <agraf@suse.de>
SoC-specific logic may be required for all forms of cache-wide
operations; invalidate and flush of both dcache and icache (note that
only 3 of the 4 possible combinations make sense, since the icache never
contains dirty lines). This patch adds an optional hook for all
implemented cache-wide operations, and renames the one existing hook to
better represent exactly which operation it is implementing. A dummy
no-op implementation of each hook is provided.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
