This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
Show the U-Boot logo by default. This is only 7KB in size so seems like
a useful default for boards that enable a display.
If SPLASH_SCREEN is enabled, it is not enabled by default, so as not to
conflict with that feature.
Also disable it for tests, since we don't want to complicate the output.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_VIDEO_LOGO
Note that this option depends on CONFIG_DM_VIDEO now, since cfb_console is
deprecated. The only relevant code is now in splash.c
Drop the check for DM_VIDEO in that file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently we allow and explicitly check a single shared page with
StandAloneMM. This is dictated by OP-TEE which runs the application.
However there's no way for us dynamically discover the number of pages we
are allowed to use. Since writing big EFI signature list variable
requires more than a page, OP-TEE has bumped the number of shared pages to
four.
Let's remove our explicit check and allow the request to reach OP-TEE even
if it's bigger than what it supports. There's no need to sanitize the
number of pages internally. OP-TEE will fail if we try to write more
than it's allowed. The error will just trigger later on, during the
StMM access.
While at it add an error message to help users figure out what failed.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Ilias Apalodimas <apalos@gmail.com>
Enable SPL support in Kconfig and add some related option in
rk3568_common.h
Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com>
Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
At present this override function is called even when OF_BOARD is not
enabled. This makes it impossible to disable this feature and in fact
makes the OF_BOARD option useless.
Reinstate its intended purpose, so that it is possible to switch between
the appended devicetree and one provided by the board's custom function.
A follower patch adds warnings for this scenario, but for now we don't
have a Kconfig that definitively tells us that OF_BOARD should be used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sync these files, obtained from Linux v5.15.
This adds a devicetree file for rpi_4 which was not there before.
Testing shows no change so far as I can see:
- boots to U-Boot prompt on rpi0, rpi2
- boots to distro on rpi3
- boots to distro on rpi4
I am assuming that syncing with Linux is safe, but the maintainer should
know for sure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move Turris MOX specific remove_disabled_nodes() to fdt_support with
name fdt_delete_disabled_nodes(), so that others can potentially use it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add functions
fdt_node_offset_by_pathf(),
fdt_create_phandle_by_pathf(),
fdt_set_status_by_pathf()
to get node offset, get/create node phandle and set status for node
given by path/alias formatted with sprintf.
Add functions
fdt_create_phandle_by_compatible(),
fdt_set_status_by_compatible()
to get/create node phandle and set status for first node given by
compatible.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit f0921f5098 ("fdt: Sync up to the latest libfdt") introduced
fdt_generate_phandle() in libfdt, making fdt_alloc_phandle() obsolete in
fdt_support.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: "hui.song" <hui.song_1@nxp.com>
Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The macro __constant_cpu_to_be32() uses ___constant_swab32(), which for
some reason is not defined and causes the following error during
compilation:
include/linux/byteorder/little_endian.h:28:52: warning:
implicit declaration of function ‘___constant_swab32’;
did you mean ‘__builtin_bswap32’? [-Wimplicit-function-declaration]
#define __constant_cpu_to_be32(x) ((__force __be32)___constant_swab32((x)))
Declare all ___constant_swabXX() macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Due to a non-existing parameter name in macro's, use of those macro's will
cause a compiler error of "undefined reference".
Unfortunately, dm test doesn't fail because a wrong name ("&dev", hence it
is accidentally a valid name in the context of a caller site) is passed on.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Fixes: f262d4ca4b ("dm: core: Add a way to read platdata for all
child devices")
Fixes: 903e83ee84 ("dm: core: Add a way to iterate through children,
probing each")
Reviewed-by: Simon Glass <sjg@chromium.org>
This function will be commonly used in block device drivers
in the succeeding patches.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In strange cases it is possible for fdtgrep to find nothing to output.
Typically this means that the resulting SPL device tree is not going to
allow anything to boot, but at present the tree is actually invalid,
since it only has an END tag in the struct region.
The FDT spec requires at least a root node. So add a special case to
include at least this, if the FDT_REG_SUPERNODES flag is set.
This ensures that grepping an empty tree still produces a valid tree.
Also add comments to the enum since it is not completely obvious from
the names now.
The typical symptom of this problem is a message from binman:
pylibfdt error -11: FDT_ERR_BADSTRUCTURE
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds better logging support for many CCF drivers, and clarifies some
documentation regarding clk_get_rate.
-----BEGIN PGP SIGNATURE-----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=1L3q
-----END PGP SIGNATURE-----
Merge tag 'clk-2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-clk
Clock patches for v2022.01-rc3
This adds better logging support for many CCF drivers, and clarifies some
documentation regarding clk_get_rate.
Improve clk_get_rate() @return documentation that otherwise is a bit
ambiguous. At the moment I expect to return 0 as error since the return
type is 'ulong', instead the function really returns negative value in
case the corresponding function pointer is null and returns 0 if the clock
is invalid.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The resync of the device trees from Linux 5.16-rc3 caused aliases
to appear on the MMC devices which changed the numbering.
This changed the default boot device and caused boot failure.
Update the mmcdev variable to reflect the new aliases.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add a block driver which handles read/write for EFI block devices. This
driver actually already exists ('efi_block') but is not really suitable
for use as a real U-Boot driver:
- The operations do not provide a udevice
- The code is designed for running as part of EFI loader, so uses
EFI_PRINT() and EFI_CALL().
- The bind method probes the device, which is not permitted
- It uses 'EFI' as its parent device
The new driver is more 'normal', just requiring its platform data be set
up in advance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
UCLASS_EFI_LOADER is used for devices created by applications and
drivers loaded by U-Boots UEFI implementation.
This patch provides a new uclass (UCLASS_EFI_MEDIA) to be used for devices
that provided by a UEFI firmware calling U-Boot as an EFI application.
If the two uclasses can be unified, is left to future redesign.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
These names are better used for access to devices provided by an EFI
layer. Use EFI_LOADER instead here, since these are only available in
U-Boot's EFI_LOADER layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This commit modify efi_tcg2_register() to return the
appropriate error.
With this fix, sandbox will not boot because efi_tcg2_register()
fails due to some missing feature in GetCapabilities.
So disable sandbox if EFI_TCG2_PROTOCOL is enabled.
UEFI secure boot variable measurement is not directly related
to TCG2 protocol installation, tcg2_measure_secure_boot_variable()
is moved to the separate function.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CONFIG_SYS_ATA_PORT_ADDR is not used in the code anymore. Drop it and use
ATA_PORT_ADDR() locally instead.
Drop CONFIG_IDE_RESET_ROUTINE and CONFIG_IDE_SWAP_IO which are also
unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used by sandbox since it uses driver model for the timer.
Drop it.
Also update the tools_only build to avoid build errors, since it does
actually build U-Boot too. Enable DM so we can use CONFIG_TIMER,
disable EFI_LOADER to avoid an error about board_quiesce_devices() and
disable NET to avoid having to define CONFIG_AVB_BUF_ADDR
Signed-off-by: Simon Glass <sjg@chromium.org>
This can go in the related header file. Drop the CONFIG option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The device tree split into .dtsi and .dts files, common
device node for eMMC/SD, enable I2C1, UART1 for console
instead of UART0, enable the DDR 2GB memory and in
that 288MB memory is reserved for fabric buffer.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add boot command "bootcmd_ram" to support autoboot from RAM.
This feature could be useful at the very initial state of chip design
when there is only a minimal set of peripheral. (e.g. without mmc and mac ..etc)
The kernel image is default to be loaded at 0x2000000 via debug port,
and the following script serves as an example:
spl()
{
cmd="riscv64-linux-gdb -q \
-ex \"target remote $host:$port\" \
-ex \"load\" \
-ex \"thread apply all set \\\$pc=&_start\" \
-ex \"thread apply all set \\\$a0=\\\$mhartid\" \
-ex \"thread apply all set \\\$a1=<dtb address>\" \
-ex \"restore u-boot.itb binary 0x200000\" \
-ex \"restore Image binary 0x2000000\" \
-ex \"c\" \
spl/u-boot-spl
"
echo $cmd
eval $cmd
}
The address where the kernel is loaded can be altered by
changing the value of KERNEL_IMAGE_ADDR.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Broadcom bnxt L2 driver support. Used by the Broadcom
iproc platforms.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Use the return value ENOSYS for unsupported API
- pinctrl_generic_set_state
- pinctrl_select_state
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM
This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a new function to activate an existing simple frame buffer node
and add the associated reserved memory, with no-map properties.
This device tree update is only done when the video device is active
and the video buffer is used.
This patch uses '#if CONFIG_IS_ENABLED(DM_VIDEO)' because
gd->video_bottom and gd->video_top are only defined when CONFIG_DM_VIDEO
is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the helper function video_is_active() to test if one video device
is active.
This function can be used in board code to execute operation
only when the display is probed / really used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the function named lcd_dt_simplefb* to fdt_simplefb* to be aligned
with the associated file name fdt_simplefb.h/fdt_simplefb.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
This converts the following to Kconfig:
CONFIG_LCD_DT_SIMPLEFB
This patch also renames this config to CONFIG_FDT_SIMPLEFB as the code in
common/lcd_simplefb.c support CONFIG_LCD and CONFIG_VIDEO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Using mmc.dtbo from rpi-firmware to switch the controller for the SD
card slot from sdhci to sdhost causes the numbering to change; the
SD card is then not recognized at boot. Add to the range checked.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The current tpm2_pcr_read is hardcoded using SHA256. Make the
actual command to TPM configurable to use wider range of algorithms.
The current command line is kept as is i.e limited to SHA-256 only.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Platforms may have support to measure their initial firmware components
and pass the event log to u-boot. The event log address can be passed
in property tpm_event_log_addr and tpm_event_log_size of the tpm node.
Platforms may choose their own specific mechanism to do so. A weak
function is added to check if even log has been passed to u-boot
from earlier firmware components. If available, the eventlog is parsed
to check for its correctness and further event logs are appended to the
passed log.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a function that returns the number of devices in a uclass. This can be
helpful in sizing an array that needs to hold a list of them.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it is useful to search just by a partial name, such as
when looking for a sibling device that has a common name substring. Add
helper functions to handle these requirements.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support reading a string list a string at a time. Apart
from being inefficient, this makes it impossible to separate reading of
the devicetree into the of_to_plat() method where it belongs, since any
code which needs access to the string must read it from the devicetree.
Add a function which returns the string property as an array of pointers
to the strings, which is easily used by clients.
Signed-off-by: Simon Glass <sjg@chromium.org>
The details for of_property_read_string_helper() and
ofnode_read_string_index() are a little inaccurate. Fix up the comments to
avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
This method is currently called after the platform data has been freed.
But the pre_unbind() method may wish to access this, e.g. to free some
data structures stored there.
Split the unbinding of devices into two pieces, as is done with removal.
This corrects the problem.
Also tidy a code-style issue in device_remove() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This text should never change during execution, so it makes sense to
use a const char * so that it can be declared as const in the code.
Update struct cmd_tbl with a const char * pointer for 'help'.
We cannot make usage const because of the bmode command, used on mx53ppd
for example.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Adds TEE_ERROR_SHORT_BUFFER as TEE error code. This error code is
commonly used by TEEs to inform caller that the buffer(s) it provided
is too small for the desired operation.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Define identifiers for clnt_login field in struct tee_open_session_arg
based in GlobalPlatform Device TEE IDs and on the REE_KERNEL identifier
extension from OP-TEE OS.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Correct inline comment describing API function devm_scmi_process_msg().
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Certain serial SERDES protocols like 1000base-x, 2500base-x, SGMII,
USXGMII can operate either in a mode where the PHY (be it on-board or
inside an SFP module) passes the link parameters (speed, duplex, pause)
to the MAC through in-band through control words standardized by IEEE
802.3 clause 37, or in a mode where the MAC must configure (force) its
link parameters based on information obtained out-of-band (MDIO reads,
guesswork etc).
In Linux, the OF node property named "managed" is parsed by the phylink
framework, and the convention is that if a driver uses phylink, then the
presence of this property means that in-band autoneg should be enabled,
otherwise it shouldn't.
To be compatible with the OF node bindings of drivers that use phylink
in Linux, introduce parsing support for this property in U-Boot too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In the current DSA switch driver API, only the udevice of the switch
(belonging to UCLASS_DSA) is exposed, as well as an "int port" argument.
So drivers do not have access to the udevice of individual ports
(belonging to UCLASS_ETH), one of the reasons being that not all ports
have an associated UCLASS_ETH udevice.
However, all DSA ports have an OF node, and in some cases the driver
needs a handle to it, for all ports including the CPU port. Example: the
following Linux per-port device tree property:
managed = "in-band-status";
states whether a port should operate with clause 37 in-band autoneg
enabled or not.
This patch exposes a function which can be called by individual drivers
as needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This is needed for the VLAN header structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Freescale TSEC can be a DSA master, and the ports of the attached
DSA switch can have different MAC addresses compared to the TSEC.
Nonetheless, the TSEC must receive the packets on behalf of those switch
ports. Therefore, implement the promiscuous mode method to allow DSA to
set this.
Note that the init_registers() function called from eth_ops :: start
overwrites this setting. There is no reason why the RCTRL register
should be zero-initialized, so just stop clearing it so that the setting
we applied in eth_ops :: set_promisc sticks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We have implemented all what is new in UEFI specification 2.9 and relevant
for U-Boot.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Implement the EFI_EVENT_GROUP_BEFORE_EXIT_BOOT_SERVICES event group
handling.
Add the definition of EFI_EVENT_GROUP_AFTER_READY_TO_BOOT.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This commit adds the comment for efi_system_table and
efi_configuration_table structure.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The extern keyword is not needed in include/lmb.h to declare functions.
Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Correct Sphinx style comments in include/lmb.h
Add the logical memory block API to the HTML documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Defining static functions in includes should be avoided.
Function lmb_is_nomap() is only used in the unit test.
So move it to the unit test.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If bootloader was updated without running oem format, reboot will cause
boot loop because the SYSTEM stage fails.
Add a final PANIC stage running fastboot to permit recovery.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This can lead to GPT and BCB errors even if fastboot was selected early
by usb rom boot and the eMMC is blank/invalid.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
AST2600 leverages the FIT hash/signature verification to fulfill
secure boot trust chain. To improve the performance and save SW
code size for those crypto operations, the two HW crypto engine,
HACE and ACRY, are enabled.
However, both of the engines can only access to data stored in
DRAM space. Therefore, we need to move the FIT image into DRAM
before the booting.
This patch update the CONFIG_BOOTCOMMAND to execute the pre-defined
ENV variable which consists of FIT image copy to memory and booting.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Lot of PCIe controllers are using ECAM addressing. So add common ECAM
macros into U-Boot's pci.h header file which can be suitable for most
PCI controller drivers.
Replace custom ECAM address macros in every PCI controller driver by new
ECAM macros from U-Boot's pci.h header file.
Similar macros are defined also in Linux kernel. There is a small
difference between Linux and these new U-Boot macros.
U-Boot's PCIE_ECAM_OFFSET() takes device and function numbers in separate
arguments. Linux's PCIE_ECAM_OFFSET() takes device and function numbers
encoded in one argument. The reason is that U-Boot's PCI_DEVFN() macro is
different than Linux's PCI_SLOT() macro. So having device and function
numbers in separate arguments makes code more straightforward.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This has different semantics in different places. Go with the bootm method
and put it in a common function so that the behaviour is consistent in
U-Boot. Update the docs.
To be clear, this changes the way that 'bootelf' and standalone boot
work. Before, if autostart was set to "fred" or "YES", for example, they
would consider that a "yes". This may change behaviour for some boards,
but the only in-tree boards which mention autostart use "no" to disable
it, which will still work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Wolfgang Denk <wd@denx.de>
Use a text file for the environment instead of the #define settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
At present U-Boot environment variables, and thus scripts, are defined
by CONFIG_EXTRA_ENV_SETTINGS. It is painful to add large amounts of text
to this file and dealing with quoting and newlines is harder than it
should be. It would be better if we could just type the script into a
text file and have it included by U-Boot.
Add a feature that brings in a .env file associated with the board
config, if present. To use it, create a file in a board/<vendor>
directory, typically called <board>.env and controlled by the
CONFIG_ENV_SOURCE_FILE option.
The environment variables should be of the form "var=value". Values can
extend to multiple lines. See the README under 'Environment Variables:'
for more information and an example.
In many cases environment variables need access to the U-Boot CONFIG
variables to select different options. Enable this so that the environment
scripts can be as useful as the ones currently in the board config files.
This uses the C preprocessor, means that comments can be included in the
environment using /* ... */
Also support += to allow variables to be appended to. This is needed when
using the preprocessor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Marek Behún <marek.behun@nic.cz>
This is a complicated set of #defines and it is painful to convert to a
text file. We can (once pending patches are applied) provide the same
functionality with bootmethod. Drop this for sandbox to allow conversion
to a text-file environment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Compiler is not happy:
common/image-board.c: In function ‘boot_get_kbd’:
common/image-board.c:902:17: warning: implicit declaration of function ‘do_bdinfo’ [-Wimplicit-function-declaration]
902 | do_bdinfo(NULL, 0, 0, NULL);
| ^~~~~~~~~
Move the forward declaration to a header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix dfu_alt_info to use nor1 instead of the device name.
This reverts a part of commit 59bd18d4c4 ("configs: synquacer:
Remove mtdparts settings and update DFU setting") because the
commit a4f2d83414 ("mtd: spi: nor: force mtd name to "nor%d"")
changed the mtd device naming scheme to nor%d.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This symbol has been functionally dead for a long time. Remove the last
and recent re-introductions of setting it, and update the whitelist so
it will not be re-introduced again.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_TRACE
CONFIG_TRACE_BUFFER_SIZE
CONFIG_TRACE_EARLY
CONFIG_TRACE_EARLY_ADDR
CONFIG_TRACE_EARLY_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH
CONFIG_ENV_IS_NOWHERE
CONFIG_ENV_OFFSET
CONFIG_ENV_OVERWRITE
CONFIG_ENV_SECT_SIZE
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Signed-off-by: Tom Rini <trini@konsulko.com>
The last board that used to set CONFIG_LYNXKDI has been removed in
commit 242836a893 ("powerpc: ppc4xx: remove pcs440ep support"),
doc/README.lynxkdi only talks about a MPC8260 board being supported,
and the mpc8260 support has been removed four years ago in commit
2eb48ff7a2 ("powerpc, 8260: remove support for mpc8260") already,
and common/lynxkdi.c only consists of an "#error" statement these
days, so it seems like the LYNX KDI code is dead code nowadays.
Let's remove it now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Refactor this code so that we can call the 'pxe get' command without going
through the command-line interpreter. This makes it easier to get the
information we need, without going through environment variables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
It is pretty strange that the pxe code uses the 'filesize' environment
variable find the size of a file it has just read.
Partly this is because it uses the command-line interpreter to parse its
request to load the file.
As a first step towards unwinding this, return it directly from the
getfile() function. This makes the code a bit longer, for now, but will be
cleaned up in future patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add an xtoa() function, similar to itoa() but for hex instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
This function no longer makes sense, since it is pretty easy to prepend
the boot directory to the filename. Drop it and update its only caller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The 'bootfile' environment variable is read in the bowels of pxe_util to
provide a directory to which all loaded files are relative.
This is not obvious from the API to PXE and it is strange to make the
caller set an environment variable rather than pass this as a parameter.
The code is also convoluted, which this feature implemented by
get_bootfile_path().
Update the API to improve this. Unfortunately this means that
pxe_setup_ctx() can fail, so add error checking.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Both the syslinux and pxe commands use essentially the same code to parse
and run extlinux.conf files. Move this into a common function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Move the header file into the main include/ directory so we can use it
from the bootmethod code. Move the C file into boot/ since it relates to
booting.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
There's a lot of code duplication in U-Boot right now. All the TPM TIS
compatible drivers we have at the moment have their own copy of a TIS
implementation.
So let's create a common layer which implements the core TIS functions.
Any driver added from now own, which is compatible with the TIS spec, will
only have to provide the underlying bus communication mechanisms.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
In some part of STM32MP15 support the CONFIG_TFABOOT can be replaced
by other config: CONFIG_ARMV7_PSCI and CONFIG_ARM_SMCCC.
This patch also simplifies the code in cpu.c, stm32mp1_ram.c and
clk_stml32mp1.c as execution of U-Boot in sysram (boot without SPL and
without TFA) is not supported: the associated initialization code is
present only in SPL.
This cleanup patch is a preliminary step to support SPL load of OP-TEE
in secure world, with SPL in secure world and U-Boot in no-secure world.
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add a configuration file "stm32mp15_st_common.h" to handle the
STMicroelectronics boards configuration and rename stm32mp1.h to
"stm32mp15_common.h" to handle the generic STM32MP15x series configuration.
The configuration file "dh_stm32mp1.h" is also renamed to
"stm32mp15_dh_dhcom" for the configuration of board based on the
dhelectronics STM32MP15x SOM.
In the STMicroelectronics board configuration the default bootcmd
"bootcmd_stm32mp" is updated to only select the extlinux file found on
SD-Card on STM32MP15x EV1 for boot from NOR device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LS1046A-QDS has CONFIG_SPI_FLASH_SST, CONFIG_SPI_FLASH_EON and
CONFIG_SPI_FLASH_STMICRO defines present in header. Move these entries
from header to defconfigs.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a helper to iterate over all nodes with a given compatible string.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that everything is prepared, copy the fsl-ls1028a.dtsi from the
linux kernel v5.14.12.
Notable changes:
- second watchdog added
- the number of chip selects of the SPI controller is now correct and
reflects what the hardware offers
- the LPUARTs have the correct clock parent
- USB controllers are enabled by default, which was already the case
before this sync because all board enabled all the USB controller
nodes. A linux patch to fix this is pending.
- the eSDHC controller changes from big-endian to little-endian, but
that property seems to be not used at all.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable support for update over EFI UpdateCapsule mechanism. This board
doesn't support setting EFI variables after ExitBootservices().
Therefore, we are also enabling EFI_IGNORE_OSINDICATIONS.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add a function to return this information along with a stub for the
efi_info_get() function, since calling it otherwise hangs U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This commit adds the EFI_TCG2_PROTOCOL.SubmitCommand
required in the TCG PC Client PFP spec.
SubmitCommand enables to send the raw command to the TPM device.
To implement this api, tpm2_submit_command() is added
into tpm-v2.c.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F
CONFIG_BOARD_LATE_INIT
CONFIG_DISPLAY_BOARDINFO
CONFIG_DISPLAY_BOARDINFO_LATE
Signed-off-by: Tom Rini <trini@konsulko.com>
Add an option to automatically register watchdog devices with the
wdt_reboot driver for use with sysreset. This allows sysreset to be a
drop-in replacement for platform-specific watchdog reset code, without
needing any device tree changes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Allow usage of the bootstage facilities in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Check sizeof(default_environment) against ENV_SIZE in a static_assert()
instead of runtime.
Only check if !USE_HOSTCC (for in fw_env tool ENV_SIZE expands to a
variable, and cannot be checked statically) nad
!DEFAULT_ENV_INSTANCE_EMBEDDED, for in that case the default_environment
variable is not set.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sometimes we use uchar and sometimes char for the default environment
array. By always using char, we can get rid of some explicit casts.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
The data blob apparently does not need to be modified through the fit
field of the image_sign_info struct so make it point to const to avoid
the need to cast away constness in functions that assign a pointer to
const data to the field.
fit_image_setup_verify already had to cast away constness as it assigned
a const void * argument to the field. The cast can now be removed.
Signed-off-by: Hannu Lounento <hannu.lounento@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Samsung S9 SM-G9600 - Snapdragon SDM845 version of the phone,
for China \ Hong Kong markets.
Has unlockable bootloader, unlike SM-G960U (American market version),
which allows running u-boot as a chain-loaded bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Hi-end qualcomm chip, introduced in late 2017.
Mostly used in flagship phones and tablets of 2018.
Features:
- arm64 arch
- total of 8 Kryo 385 Gold / Silver cores
- Hexagon 685 DSP
- Adreno 630 GPU
Tested only as second-stage bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Add preliminary device trees for the Apple M1 mini (2020) and
Apple M1 Macbook Pro 13" (2020). Device tree bindings for
the Apple M1 SoC are still being formalized and these device
trees will be synchronized with the Linux kernel as needed.
The device trees in this commit are based on the initial Apple
M1 device trees from Linux 5.13, nodes for dart, pcie, pinctrl,
pmgr, usb based on bindings on track for inclusion in Linux
5.15 and 5.16 and nodes for i2c, mailbox, nvme, pmu, spmi and
watchdog that don't have a proposed binding yet.
These device trees are provided as a reference only as U-Boot
uses the device tree passed by the m1n1 bootloader.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Apple's M1 SoC that is used in "Apple Silicon"
Macs. This builds a basic U-Boot that can be used as a payload
for the m1n1 boot loader being developed by the Asahi Linux
project.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add MAINTAINERS entry]
This uclass is intended to manage IOMMUs on systems where the
IOMMUs are not in bypass mode by default. In that case U-Boot
cannot ignore the IOMMUs if it wants to use devices that need
to do DMA and sit behind such an IOMMU.
This initial IOMMU uclass implementation does not implement and
device ops and is intended for IOMMUs that have a bypass mode
that does not require address translation. Support for IOMMUs
that do require address translation is planned and device ops
will be defined when support for such IOMMUs will be added.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds an implementation of the wait_dat0 MMC operation for the DM SDHCI
driver, allowing the driver to continue when the card is ready rather
than waiting for the worst case time on each MMC switch operation.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
OF_HOSTFILE is used on sandbox configs only. Although it's pretty
unique and not causing any confusions, we are better of having simpler
config options for the DTB.
So let's replace that with the existing OF_BOARD. U-Boot would then
have only three config options for the DTB origin.
- OF_SEPARATE, build separately from U-Boot
- OF_BOARD, board specific way of providing the DTB
- OF_EMBED embedded in the u-boot binary(should not be used in production
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds the UEFI GPT disk partition topology
measurement required in TCG PC Client Platform Firmware
Profile Specification
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
First two fields are reversed compared to what is expected by the SCMI
specification.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Fixes: 6038884483 ("clk: add clock driver for SCMI agents")
TCG PC Client Platform Firmware Profile Specification
requires to measure the SMBIOS table that contains static
configuration information (e.g. Platform Manufacturer
Enterprise Number assigned by IANA, platform model number,
Vendor and Device IDs for each SMBIOS table).
The device- and environment-dependent information such as
serial number is cleared to zero or space character for
the measurement.
Existing smbios_string() function returns pointer to the string
with const qualifier, but exisintg use case is updating version
string and const qualifier must be removed.
This commit removes const qualifier from smbios_string()
return value and reuses to clear the strings for the measurement.
This commit also fixes the following compiler warning:
lib/smbios-parser.c:59:39: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
const struct smbios_header *header = (struct smbios_header *)entry->struct_table_address;
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Make sure to (if applicable) flush the D-cache, invalidate I-cache,
and disable MMU and caches before jumping to OPTEE.
This fixes the SDP->SPL->OPTEE boot flow on iMX6Q and most likely on
some other ARM SoCs.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
In multiple places we need the default GUID matching a variable name.
The patch provides a library function. For secure boot related variables
like 'PK', 'KEK', 'db' a lookup table is used. For all other variable
names EFI_GLOBAL_VARIABLE is returned.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
UEFI variable names are typically constants and hence should be defined as
const. Unfortunately some of our API functions do not define the parameters
for UEFI variable names as const. This requires unnecessary conversions.
Adjust parameters of several internal functions to tre UEFI variable names
as const.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit fixes the following compilation warning
of boottime->install_configuration_table() function.
lib/efi_selftest/efi_selftest_tcg2.c:475:46:
warning: passing argument 1 of ‘boottime->install_configuration_table’
discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
ret = boottime->install_configuration_table(&smbios_guid, dmi);
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
- Add and enable watchdog driver
- Prepare for SYSRESET driven AXP poweroff
- Prepare for SoCs without MMC2
- Some fixes for extending SPL (SPL-DM for RISC-V)
- Some preparations for proper VBUS management
- Fix secure monitor move
A single DM-based driver should be able to support some feature for
several PMIC variants where the interface is the same. For example,
all PMIC variants use the same register bit to trigger poweroff.
However, currently only definitions for a single PMIC are available at
a time. This requires drivers to use #ifdefs and different indentifiers
for each variant they support.
Let's simplify this by making register definitions for all variants
available from the header. Then no preprocessor conditions are needed;
the driver can use the register definition from any variant that
supports the relevant feature.
An exception is the GPIO-related definitions, which do not use unique
identifiers. So for now, keep them like before. They will be cleaned up
along with the GPIO driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This header attempted to avoid multiple inclusion using a header guard.
But the preprocessor symbol was never defined, so the guard had no
effect. Fix this by defining the symbol.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
commit 1ebfc0c631 ("sunxi: A23/A33/H3: Move sun8i secure monitor to
SRAM A2") attempted to move the secure monitor to SRAM A2. But not all
sun8i SoCs have SRAM A2, so a check was put in for SUNXI_SRAM_A2_SIZE to
avoid breaking the other SoCs.
However, because the header providing SUNXI_SRAM_A2_SIZE was not
included, this unintentionally skipped the new definitions on all SoCs.
Fix this by including the right header.
Fixes: 1ebfc0c631 ("sunxi: A23/A33/H3: Move sun8i secure monitor to SRAM A2")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The original purpose of mtd_erase_callback() in Linux at the time it was
imported to U-Boot, was to inform the caller that erasing is done (since
it was an asynchronous operation).
All supplied callback methods in U-Boot do nothing, but the
mtd_erase_callback() function was (until previous patch) grossly abused
in U-Boot's mtdpart implementation for completely different purpose.
Since we got rid of the abusement, remove the mtd_erase_callback()
function and the .callback member from struct erase_info entirely, in
order to avoid such problems in the future.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Check for zero length in the legacy spi_flash_read() /
spi_flash_write() / spi_flash_erase() functions.
On zero length, return 0 immediately, don't call the underlying method.
Rationale:
- these legacy functions call the _read(), _write() and _erase() methods
of struct mtd
- the DM callers of these methods already check for zero length
- making all callers of these methods check for zero length makes it
possible to remove the check from implementations of these _read(),
_write() and _erase() methods
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Currently the env_get_f() function's return value behaves weirdly: it
returns the number of bytes written into `buf`, but whether this is
excluding the terminating NULL-byte or including it depends on whether
there was enough space in `buf`.
Change the function to always return the actual length of the value of
the environment variable (excluding the terminating NULL-byte) on
success. This makes it behave like sprintf().
All users of this function in U-Boot are compatible with this change.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function is a relic from the past when environment was read from
underlying device one character at a time.
It is used only in the case when getting an environemnt variable prior
relocation, and the function is simple enough to be inlined there.
Since env_get_char() is being changed to simple access to an array, we
can drop the failing cases and simplify the code (this could have been
done before, since env_get_char() did not fail even before).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function was used by other parts of U-Boot in the past when
environment was read from underlying device one character at a time.
This is not the case anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function actually returns:
- the number of bytes written into @buf excluding the terminating
NULL-byte, if there was enough space in @buf
- the number of bytes written into @buf including the terminating
NULL-byte, if there wasn't enough space in @buf
- -1 if the variable is not found
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix up the header's include guard to contain the definition of
dm_priv_to_rw(), which was erroneously added outside of it, by moving
its #endif to the end of the file (i.e. where it belongs). This removes
the risk of compilation errors resulting from the redefinition of that
function where the header might have been (indirectly) included more
than once.
Fixes: cfb9c9b77c ("dm: core: Use separate priv/plat data region")
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
Cc: Simon Glass <sjg@chromium.org>
Instead of declaring CONFIG_SPL_DRIVERS_MISC in board config header,
select it in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Instead of declaring CONFIG_SYS_MALLOC_SIMPLE dependant on
CONFIG_SPL_BUILD in board config header, select
CONFIG_SPL_SYS_MALLOC_SIMPLE in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reorder the definitions in Turris MOX' board config header, drop the
comment relics from when this file was copied, fix indentation.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move the config option CONFIG_I2C_MV to a Kconfig option
CONFIG_SYS_I2C_MV and move the default definition from config header
files into defconfigs.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move config options CONFIG_LAST_STAGE_INIT and
CONFIG_DISPLAY_BOARDINFO_LATE to turris_mox_defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Create the GUID as a global variable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Parameter size is never used in function efi_dp_from_lo(). Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Instead of copying a GUID and then using a pointer to the copy for calling
guidcmp(), just pass the pointer to the orginal GUID.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We are ignoring the alignment communicated via the PE/COFF header.
Starting 5.10 the Linux kernel will loudly complain about it. For more
details look at [1] (in linux kernel).
So add a function that can allocate aligned EFI memory and use it for our
relocated loaded image.
[1] c32ac11da3f83 ("efi/libstub: arm64: Double check image alignment at entry")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Vincent Stehlé <vincent.stehle@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Complete the Sphinx documentation in include/sysreset.h
Add the include to the generated HTML documentation of the U-Boot API.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add code to build the eMMC variant of the Colibri iMX6ULL, i.e. the
'Colibri iMX6ULL 1GB' which has a eMMC instead of the raw NAND used
on other SKUs.
Related-to: ELB-4056, ELB-4057
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Integrate new Toradex SKU 0062 Colibri iMX6ULL 1GB IT. This commit
basically adjusts three parameters of the RAM settings:
Increase density from 4Gb to 8Gb
Increase ROW address from 15 to 16
Increase tRFC (refresh command time) from 260 to 350
This timing is valid for all Toradex Colibri iMX6ULL SKUs
Related-to: ELB-4055, ELB-4057
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Variable "kernel_image" is used in boot.scr script only, that sets its
own default value to the constant string @@KERNEL_IMAGETYPE@@ in case
"kernel_image" is not set.
The default name of the kernel image shipped with BSP 5.x is "Image.gz".
Setting kernel_image="Image" as a pre-defined u-boot variable
breaks booting systems with modern versions of boot.scr, whereas
renaming it fixes booting with modern scripts and does not break working
of earlier versions of boot.scr.
While at it also update the copyright period, rather than hard-coding
fdtfile default fdt_board to dev for the Verdin iMX8M Mini and fix its
closing #endif comment.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Even if board can be successfuly built, CI goes in deadlock (see thread
on https://www.mail-archive.com/u-boot@lists.denx.de/msg419663.html).
This is caused by SYS_CONFIG set in header file and because defconfig
for the board is out of sync with Kconfig. As result, buildman goes on
to read from stdin until an OOM is reached.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Frieder Schrempf <frieder.schrempf@kontron.de>
Like dev_read_addr_ptr(), provide a wrapper for the indexed version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present there is only devfdt_get_addr_ptr() which only returns
the first <addr, size> pair in the 'reg' property. Add a new API
devfdt_get_addr_index_ptr() to return the indexed pointer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bulletproof the default boot command with reset statements in case
any command in the chain would fail. In case a failure were to happen,
the board will reset, increment boot counter and retry the procedure.
In case the failures persist and the boot counter reaches the bootlimit,
U-Boot starts altbootcmd instead of the default bootcmd boot command.
The altbootcmd swaps the default boot partition for the other boot
partition, which is an identical copy or an older copy, and tries
booting from that one instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Move setting CONFIG_BOOTCOMMAND to the mx7ulp_com_defconfig file.
It also allows replacing the default CONFIG_BOOTCOMMAND without
code modification.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The previous patches removed OF_PRIOR_STAGE from the last consumers of the
Kconfig option. Cleanup any references to it in documentation, code and
configuration options.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
On mvebu this is defined if and only if !ARM64.
Otherwise it is defined for boards with ARCH_MX23, ARCH_TEGRA and
ARCH_ZYNQ, and also for SOC_AR934X (tplink_wdr4300).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This option is only used for
mx23evk_defconfig
mx23_olinuxino_defconfig
which are the only i.MX23 boards.
Add depend on ARCH_MX23 and default to y.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
In preparation for moving this option to Kconfig, rename it to be
consistent with other USB EHCI Kconfig options.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Remove the latest reference of CONFIG_CONS_NONE in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the latest reference of CONFIG_SYS_FLASH_AMD_CHECK_DQ7 in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the latest reference of CONFIG_NO_RELOCATION in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This define was left over from a previous revision, and was never used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove some config finishing by _ badly added by
scripts/build-whitelist.sh when joker is used in comments.
for example:
doc/uImage.FIT/command_syntax_extensions.txt:
... #ifdef CONFIG_OF_* | ...
cmd/nvedit.c:# error Define one of CONFIG_ENV_IS_IN_{EEPROM| \
FLASH|MMC|FAT|EXT4|\
Remove also configs only used in comments:
- CONFIG_BOOGER in include/linux/kconfig.h
- CONFIG_COMMANDS
- CONFIG_INIT_IGNORE_ERROR
- CONFIG_REG_*
- CONFIG_HOTPLUG : drivers/watchdog/omap_wdt.c:18
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The EMC frequency tables are created from a training sequence performed
during early boot and passed in via a reserved memory region by nvtboot.
Copy this table to the kernel DTB so that the kernel can use it to scale
the EMC frequency at runtime.
Note that early bootloaders store the EMC table at an address that
currently intersects with the load address of the initial ramdisk. In
order to avoid copying the table to a different address, simply change
the load address for the initial ramdisk in U-Boot.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reserved memory nodes can have additional flags. Support reading and
writing these flags to ensure that reserved memory nodes can be properly
parsed and emitted.
This converts support for the existing "no-map" flag to avoid extending
the argument list for fdtdec_add_reserved_memory() to excessive length.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The fdtdec_set_carveout() function's parameters are inconsistent with
the parameters passed to fdtdec_add_reserved_memory(). Fix up the order
to make it more consistent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reserved memory nodes can have a compatible string list to identify the
type of reserved memory that they represent. Support specifying an
optional compatible string list when creating these nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When retrieving a given carveout for a device, allow callers to query
the name. This helps differentiating between carveouts when there are
more than one.
This is also useful when copying carveouts to help assign a meaningful
name that cannot always be guessed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
Fix a regression brings by commit 84f8e36f03 ("cmd: bind: allow to
bind driver with driver data")
As example, the following bind command doesn't work:
bind /soc/usb-otg@49000000 usb_ether
As usb_ether driver has no compatible string, it can't be find by
lists_bind_fdt(). In bind_by_node_path(), which called lists_bind_fdt(),
the driver entry is known, pass it to lists_bind_fdt() to force the driver
entry selection.
For this, add a new parameter struct *driver to lists_bind_fdt().
Fix also all lists_bind_fdt() callers.
Fixes: 84f8e36f03 ("cmd: bind: allow to bind driver with driver data")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).
Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.
This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the rsb functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants, so move that to the common header.
There are only a couple of pairs of hardware/runtime addresses used
across all PMIC variants. So far the code expected only the "primary"
pair, but some PMICs like the AXP305 and AXP805 use the secondary pair,
so add support for that to the DM driver as well.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the p2wi functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants. Move that to the common header, so it can be used by
both interface implementations.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Account for the changes done between merge proposal and the final merge.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The CCU header is only used by the DM drivers, not any platform code.
Its current location adds an artificial dependency on CONFIG_ARM and
ARCH_SUNXI, which will be problematic when adding the CCU driver for
a RISC-V sunxi platform.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Move CONFIG_VIDEO_MXS from board headers to Kconfig
and drop it from obsolete cfb_console driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
At present U-Boot has a header file called lz4.h for its own use. If the
host has its own lz4 header file installed (e.g. from the 'liblz4-dev'
package) then host builds will use that instead.
Move the U-Boot file into its own directory, as is done with various
other headers with the same problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for 30bpp mode where pixels are picked in 32-bit
integers but use 10 bits instead of 8 bits for each component.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
This file has a lot of conditional code and much of it is unnecessary.
Clean this up to reduce the number of build combinations.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is only used in one place and does not need to use the
preprocessor. Move it to the C file and convert it to a normal function.
Drop fit_unsupported() since it is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
We can use the new host_build() function for this, so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough and the board code is now in a separate file. Update the only place
where this is used and drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for FIT_RSASSA_PSS. With this we can use
CONFIG_IS_ENABLED(FIT_RSASSA_PSS) directly in the host build, so drop the
forcing of this in the image.h header.
Drop the #ifdef around padding_pss_verify() too since it is not needed.
Use the compiler to check the config where possible, instead of the
preprocessor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for FIT_VERBOSE. With this we can use
CONFIG_IS_ENABLED(FIT_VERBOSE) directly in the tools build, so drop the
forcing of this in the image.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for OF_LIBFDT. With this we can use
CONFIG_IS_ENABLED(OF_LIBFDT) directly in the tools build, so drop the
unnecessary indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Make use of the host Kconfig for FIT. With this we can use
CONFIG_IS_ENABLED(FIT) directly in the host build, so drop the unnecessary
indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
At present when building host tools, we force CONFIG_SHAxxx to be enabled
regardless of the board Kconfig setting. This is done in the image.h
header file.
For SPL we currently just assume the algorithm is desired if U-Boot proper
enables it.
Clean this up by adding new Kconfig options to enable hashing on the host,
relying on CONFIG_IS_ENABLED() to deal with the different builds.
Add new SPL Kconfigs for hardware-accelerated hashing, to maintain the
current settings.
This allows us to drop the image.h code and the I_WANT_MD5 hack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
At present we must separately test for the host build for many options,
since we force them to be enabled. For example, CONFIG_FIT is always
enabled in the host tools, even if CONFIG_FIT is not enabled by the
board itself.
It would be more convenient if we could use, for example,
CONFIG_IS_ENABLED(FIT) and get CONFIG_HOST_FIT, when building for the
host. Add support for this.
With this and the tools_build() function, we should be able to remove all
the #ifdefs currently needed in code that is build by tools and targets.
This will be even nicer when we move to using CONFIG(xxx) everywhere,
since all the #ifdef and IS_ENABLED/CONFIG_IS_ENABLED stuff will go away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> # b4f73886
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
With the new TOOLS_LIBCRYPTO and some other changes, it seems that we are
heading towards calling this a tools build rather than a host build,
although of course it does happen on the host.
I cannot think of anything built by the host which cannot be described as
a tool, so rename this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a macro to handle manually relocating a pointer. Update the iamge code
to use this to avoid needing #ifdefs.
This also fixes a bug where the 'done' flag was not set.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than adding an #ifdef and open-coding this calculation, add a
helper function to handle it. Use this in the image code.
Signed-off-by: Simon Glass <sjg@chromium.org>
The gzip API uses the u64 type in it, which is not available in the host
build. This makes it impossible to include the header file.
We could make this type available, but it seems unnecessary. Limiting the
compression size to that of the 'unsigned long' type seems good enough. On
32-bit machines the limit then becomes 4GB, which likely exceeds available
RAM anyway, therefore it should be sufficient. On 64-bit machines this is
effectively u64 anyway.
Update the header file and implementation to use 'ulong' instead of 'u64'.
Add a definition of u32 for the cases that seem to need exactly that
length. This should be safe enough.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing zstd API requires the same sequence of calls to perform its
task. Create a helper for U-Boot, to avoid code duplication, as is done
with other compression algorithms. Make use of of this from the image
code.
Note that the zstd code lacks a test in test/compression.c and this should
be added by the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
When passing a data buffer back from a function, it is not always clear
who owns the buffer, i.e. who is responsible for freeing the memory used.
An example of this is where multiple files are decompressed from the
firmware image, using a temporary buffer for reading (since the
compressed data has to live somewhere) and producing a temporary or
permanent buffer with the resuilts.
Where the firmware image can be memory-mapped, as on x86, the compressed
data does not need to be buffered, but the complexity of having a buffer
which is either allocated or not, makes the code hard to understand.
Introduce a new 'abuf' which supports simple buffer operations:
- encapsulating a buffer and its size
- either allocated with malloc() or not
- able to be reliably freed if necessary
- able to be converted to an allocated buffer if needed
This simple API makes it easier to deal with allocated and memory-mapped
buffers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that PCI Bridge (PCIe Root Port) for Aardvark is emulated in U-Boot,
add support for handling and propagation of CRSSVE bit.
When CRSSVE bit is unset (default), driver has to reissue config
read/write request on CRS response.
CRSSVE bit is supported only when CRSVIS bit is provided in read-only
Root Capabilities register. So manually inject this CRSVIS bit into read
response for that register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Remove the latest reference of CONFIG_USER_LOWLEVEL_INIT in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move CONFIG_BOOTCOMMAND defined in Kconfig in the board defconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Using the tools moveconfig.py to move the following config in the
defconfig files:
CONFIG_USB_HOST_ETHER
CONFIG_USB_ETHER_ASIX
CONFIG_USB_ETHER_MCS7830
CONFIG_USB_ETHER_SMSC95XX
These option are already migrated since the commit f58ad98a62 ("usb: net:
migrate USB Ethernet adapters to Kconfig") and the commit ae3584498b
("usb: net: migrate CONFIG_USB_HOST_ETHER to Kconfig").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the CONFIG_STM32_FLASH to Kconfig by using
tools/moveconfig.py
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This reverts commit d5d726d3cc,
which breaks boards which ship with multiple SD/eMMC sockets.
This stm32mp1.h config is not used only by the ST reference
boards, but all the other STM32MP1 based boards in U-Boot, so
changes to this stm32mp1.h cannot break the other boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
These platforms never had to support an ATAGs-based Linux Kernel, so
remove the options.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Import HS400 support for iMX7ULP B0 from the Linux kernel:
2eaf5a533afd ("mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP")
According to IC suggest, need to clear the STROBE_DLL_CTRL_RESET
before any setting of STROBE_DLL_CTRL register.
USDHC has register bits(bit[27~20] of register STROBE_DLL_CTRL)
for slave sel value. If this register bits value is 0, it needs
256 ref_clk cycles to update slave sel value. IC suggest to set
bit[27~20] to 0x4, it only need 4 ref_clk cycle to update slave
sel value. This will short the lock time of slave.
i.MX7ULP B0 will need more time to lock the REF and SLV, so change
to add 5us delay.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
When using SWUpdate, it is necessary to toggle between partitions.
Use the 'mmcpart' environment variable to accomplish that.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The CONFIG_SPL_MAX_SIZE definition did not account for all areas that
are used by the boot ROM according to the manual, causing boot failures
due to truncated SPL images when actually hitting this limit.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
The BSP platform LmP supports the board NXP iMX8QM MEK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
The BSP platform LmP supports the board NXP iMX8M Plus EVK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
The BSP platform LmP supports the board NXP iMX8M Mini EVK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
add hook function spl_load_simple_fit_fix_load()
which is called after fit image header is loaded.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
JetHub devices uses its own boot sequence with "rescue" button
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SCSI device can be a PCIe adapter, so run pcie enum if enabled.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SCSI target to be able to boot from the SATA disks on the Odroid HC4 using
an on-board AHCI PCIe controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Import Amlogic DT changes from Linux commit 7d2a07b76933 ("Linux 5.14"),
dt-bindings clock changes and new meson-g12b-gsking-x.dts,
meson-sm1-bananapi-m5 & odroid-hc4 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Typically platforms will define CONFIG_SYS_NAND_PAGE_COUNT based on
CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE. Switch to this
in preparation for migrating CONFIG_SYS_NAND namespace to Kconfig.
Cc: Marek Vasut <marex@denx.de>
Cc: Olaf Mandel <o.mandel@menlosystems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These platforms do not currently enable NAND, remove these references.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The generic GPIO flags binding is shared across many drivers, some of
which need their own xlate function. Factor out the flag translation
code from gpio_xlate_offs_flags so it does not need to be duplicated.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This value is not used by u-boot, and it should not. The load address
of an OPTEE image is defined by said image. Either a uImage or a FIT
will have a defined load address and entry point. Those values are the
correct ones, not CONFIG_OPTEE_LOAD_ADDR.
Commit f25006b96e ("optee: Add CONFIG_OPTEE_LOAD_ADDR") justifies
this config by requiring its presence in u-boot's .config for other
images as part of a larger build, claiming it is "the best way".
This argument is not persuasive. U-boot's configuration is driven by
platform requirements, not the other way around. It seems more likely
that the argument is conflating tooling issues with Kconfig. Yocto and
buildroot have excellent mechanisms for defining values across the
board (pun intended). u-boot's Kconfig is the wrong place to do it.
Furthermore, it is not "best" for u-boot because it hardcodes a value
which is then not used. In fact the load address that u-boot uses is
the one derived from the OPTEE image.
Confused yet? I sure was. To prevent future confusion, remove
CONFIG_OPTEE_LOAD_ADDR.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
