Sometimes it is desireable to have the console output on the first
serial line. Introduce a configuration option for it (in the board
scope).
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is not recommended to use CONFIG_xxx defines for things which are not
Kconfig options. Rename this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
QEMU ppce500 target can dynamically instantiate an eTSEC device on
a platform bus if "-device eTSEC" is given to QEMU. It is presented
as a "simple-bus" in the device tree, with an additional compatible
string "qemu,platform".
Let's create a virtual memory mapping for it in misc_init_r(), in
preparation to adding eTSEC support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.
It is based on NXP LS1021 SoC and it provides following interfaces:
- IFC interface for NOR, NAND and external FPGA's
- 1 x RGMII ETH for debug purposes
- 2 x SGMII ETH for management communication via back-plane
- 1 x uQE HDLC for management communication via back-plane
- 1 x I2C for peripheral devices
- 1 x SPI for peripheral devices
- 1 x UART for debug logging
It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Select CMD_QFW and QFW_MMIO in the qemu-arm board (covers arm and
arm64).
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We move qfw into its own uclass and split the PIO functions into a
specific driver for that uclass. The PIO driver is selected in the
qemu-x86 board config (this covers x86 and x86_64).
include/qfw.h is cleaned up and documentation added.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
It's an old bringup board with out upstream Linux or L4T support
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Add power_max77696_init() function.
Since warp doesn't support DM, the keeping its code in board file is
better than maintainig the file of driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. It is also the only ARCH_T2081 board so remove that support
as well.
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <linuxfae@technexion.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Thomas Weber <weber@corscience.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM by the deadline.
Remove them.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Steve Rae <steve.rae@raedomain.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Erik van Luijk <evanluijk@interact.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. In order to
convert to using the DWC SATA driver under DM further migrations are
required.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
-----BEGIN PGP SIGNATURE-----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=4VxR
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210409' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
Simplify the code of the function board_check_usb_power
based in CONFIG_ADC and adc_measurement; the function is removed by the
linker when the CONFIG_ADC is not activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
7" OF is a capacitive touch 7" Open Frame panel solutions with
- 7" AUO B101AW03 LVDS panel
- EDT, FT5526 Touch
MicroGEA STM32MP1 is a STM32MP157A based Micro SoM.
MicroDev 2.0 is a general purpose miniature carrier board with CAN,
LTE and LVDS panel interfaces.
MicroGEA STM32MP1 needs to mount on top of MicroDev 2.0 board with
pluged 7" OF for creating complete MicroGEA STM32MP1 MicroDev 2.0
7" Open Frame Solution board.
Linux dts commit details:
commit <1d278204cbaa> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 7" OF")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
MicroDev 2.0 is a general purpose miniature carrier board with CAN,
LTE and LVDS panel interfaces.
Genaral features:
- Ethernet 10/100
- USB Type A
- Audio Out
- microSD
- LVDS panel connector
- Wifi/BT (option)
- UMTS LTE with sim connector (option)
MicroGEA STM32MP1 is a STM32MP157A based Micro SoM.
MicroGEA STM32MP1 needs to mount on top of this MicroDev 2.0 board
for creating complete MicroGEA STM32MP1 MicroDev 2.0 Carrier board.
Linux dts commit details:
commit <f838dae7afd0> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 board")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.
Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.
i.Core STM32MP1 needs to mount on top of this Carrier board for
creating complete i.Core STM32MP1 C.TOUCH 2.0 board.
Linux dts commit details:
commit <6ca2898df59f> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
C.TOUCH 2.0")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.
i.Core STM32MP1 needs to mount on top of this Evaluation board for
creating complete i.Core STM32MP1 EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <adc0496104b6> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
EDIMM2.2 Starter Kit")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
All these files are add for support rt-thread art-pi board
- add board/st/stm32h750-art-pi, defconfig, header support for u-boot
for more information about art-pi, please goto:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Pass "pfuze3000@8" in pmic_get() so that the PMIC node can
be found in the devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Convert the Olimex Olinuxino board's support for MMC to driver model following
Fabio Estevam's excellent example from:
commit: 23013aa961:
mx23evk: Convert to driver model
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Convert the UDOO board to use DM_ETH.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block, DM MMC and DM SATA support on iMX6 Udoo
convert board code to match the DM support.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Convert the two Embest boards to use DM MMC.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
While initializing dram in spl_dram_init(), mdelay() is called that in
order calls get_ticks() that verifies if timer exists, if doesn't, it
throws a panic(), but since preloader_console_init() has still not been
called those panic()s will fail. This doesn't help debugging, so let's
setup console before calling spl_dram_init() by moving it after
spl_dram_init().
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
While initializing dram in spl_dram_init(), mdelay() is called that in
order calls get_ticks() that verifies if timer exists, if doesn't, it
throws a panic(), but since preloader_console_init() has still not been
called those panic()s will fail. This doesn't help debugging, so let's
setup console before calling spl_dram_init() by moving it after
spl_dram_init().
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
While initializing dram in spl_dram_init(), mdelay() is called that in
order calls get_ticks() that verifies if timer exists, if doesn't, it
throws a panic(), but since preloader_console_init() has still not been
called those panic()s will fail. This doesn't help debugging, so let's
setup console before calling spl_dram_init() by moving it after
spl_dram_init().
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
use dm_i2c_probe instead of i2c_get_chip which appears to be more
reliable.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model for MTD and NAND support allowing us to remove
the iomux, init, and most of the static configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable driver model support for MMC and SATA.
Note that DM_MMC requires aliases for your mmc devices so
they are added to the dts. Linux does not support enumerating mmc
devices by alias so these are not present in the Linux dts.
Note that we still need board_mmc_init() and board_mmc_getcd() for
not DM SPL to support MMC.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable dm support for USB (which also requires dm support for fixed
regulators used for vbus enable) and remove usb iomux which is no
longer needed.
We can remove the handling of otgpwr_en gpio as this is defined in
dt as usbotg vbus-supply but we need to keep the handling of
USB_HUB_RST# for boards that have a USB HUB as that isn't defined in
the dt's currently.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Once the IMX6 pinctrl driver is added UART is fully using driver mode
so we no longer need to config and initialize it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
In preparation for dm conversion convert to OF_CONTROL by adding FIT image
support and multi dtb.
Add a board_fit_config_name_match to match the dtb based off of EEPROM
model.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
In preparation to add SiFive Unmatched board support, let's rename
the existing fu540 board to unleashed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Both i.MX8MQ B1 and B2 should use default LPDDR4 script, while B0
has another dedicated script.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Users reported LPDDR4 MR12 value is set to 0 during PHY training,
not the value from FSP timing structure, which cause compliance test failed.
The root cause is the CATrainOpt[0] is set to 1 in 2D FSP timing
but not set in 1D. According to PHY training application node,
to enable the feature both 1D and 2D need set this field to 1,
otherwise the training result will be incorrect.
The PHY training doc also recommends to set CATrainOpt[0] to 0 to use
MR12 value from message block (FSP structure). So update the LPDDR4
scripts of all mscale to clear CATrainOpt[0].
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add dedicated defconfigs for iMX8MN low drive mode which set the VDD_SOC
and VDD_DRAM to 0.8v, DDR at 1600MTS (800Mhz clock) and GPU at 200Mhz.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for iMX8MN LPDDR4 EVK board which uses 2GB LPDDR4 and
PCA9450B PMIC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
On i.MX8MN, we can only support DLL-ON mode only, so update the timing
to support 2400mts & 1066mts setpoint.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is a frequency/timing limitation for SOC and ARM, if SOC is OD
voltage/OD freq, then ARM can't run at ND voltage/1.2Ghz, it may have
timing risk from SOC to ARM.
Current VDD_SOC is set to 0.95v OD voltage in SPL, and kernel will
increase bus clocks to OD frequency before it increases ARM voltage.
So to conform to the limitation, we'd better increases VDD_ARM to OD
voltage in SPL.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
VDD SOC normal run changed to 0.85V
LPDDR4 freq0 change from 4000MTS to 2400MTS
Signed-off-by: haidong.zheng <haidong.zheng@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use more safer refresh time value for 6GB LPDDR4 on this EVK board.
Update the parameters for every frequency point.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
After switching to new LPDDR4 firmware 202006 version, have to
update the LPDDR4 timing accordingly from RPA tool.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Sherry Sun <sherry.sun@nxp.com>
Tested-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add inline ECC support for lpddr4 on imx8mp-evk. And add a config which
can enable/disable inline ECC feature for lpddr4 on imx8mp-evk board.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Define a misc_init_r() which calls "syno populate_env" if the
environment seems incomplete (or default), indicated by missing
"ethaddr" variable. With this in place, no random MAC address fallback
is needed anymore.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Move the relevant bits from ds109.{c,h} into common/ and adjust the code
to fit both DS109 and DS414. Moreover:
* Introduce syno_board_id() which translates CONFIG_MACH_TYPE into the
expected board ID tag value.
* Properly initialize isusbhost, mac and mtu fields from env variables.
* Set the right bootargs/bootcmd to correctly boot legacy kernel out of
the (DS414) box. Getting the ramdisk location right is a bit tedious.
Cc: Walter Schweizer <swwa@users.sourceforge.net>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
The static ethernet link type config code is no more needed because now handled by
the meson8b glue driver, delete it.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add initial support for NanoPi M4B, a minor revision of
the original NanoPi M4.
Commit details of rk3399-nanopi-m4b.dts sync from Linux 5.12-rc4:
"arm64: dts: rockchip: Add NanoPi M4B board"
(sha1: c7b03115003f7f337ab165542cee37148cf30a8a)
Signed-off-by: Alexandre Vicenzi <alexandre.vicenzi@suse.com>
Reviewed-by: Kever Yang <kever.yang@rock-cihps.com>
NanoPi R4s is SBC base on Rockchip RK3399 hexa-core processor with
dual-Core Cortex-A72 and Mali-T864 GPU with 4GiB(LPDDR4) of RAM, SD card support,
including 2 gigabit ethernet(RTL8211E 1Gbps - RTL8111H 1Gbps) and 2 USB 3.0 port.
port.It also has two GPIO headers which allows further peripherals to be used.
The devicetree file is taken of the rk3399 nanopi4 Linux kernel [1].
[1] e7a0959082
Signed-off-by: xiaobo <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On Puma we have the environment at an offset of 16 kiB.
On the eMMC this gives us 16 kiB for the environment before the SPL starts.
On the SPI NOR we also have 16 kiB until end of flash.
So let's increase the environment size from 8 kiB to its maximum
of 16 kiB for both MMC and SPI NOR.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Provide the model information through sysinfo so that it shows up on
boot. For memconfig 4 pins are provided, for 16 combinations. For SKU
ID there are two options:
- two pins provided in a ternary arrangement, for 9 combinations.
- reading from the EC
Add a binding doc and drop the unused #defines as well.
Example:
U-Boot 2021.01-rc5
CPU: Intel(R) Celeron(R) CPU N3450 @ 1.10GHz
DRAM: 3.9 GiB
MMC: sdmmc@1b,0: 1, emmc@1c,0: 2
Video: 1024x768x32 @ b0000000
Model: Google Coral (memconfig 5, SKU 3)
This depends on the GPIO series:
http://patchwork.ozlabs.org/project/uboot/list/?series=228126
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
It is possible to boot U-Boot for chromebook_coral either 'bare metal' or
from coreboot. In the latter case we want to provide access to the coreboot
sysinfo tables. Move the definitions into a file available to any x86
board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move sandbox_spl over to use OF_PLATDATA_INST. Create a new board to
test the case when this is not enabled, since we will be keeping that
code around for several months and want to avoid regressions.
Skip the dm_test_of_plat_dev() test since driver info is not available
for OF_PLATDATA_INST.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The User Guide contains handy things like block diagrams and DIP switch
settings and it's even available on the public web. Add a link to it in
the README.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the FAT environment driver to the priority list.
When testing the UEFI sub-system the EFI system partition is formatted with
FAT so it is reasonable to store the environment there.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
More than one pumpkin board has been made with different MediaTek SoCs.
Rename the pumpkin board to follow the naming convention of all
other MediaTek boards and also to not be confusing when other pumpkin
boards will be added in follow-up commits.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Enable building SPL for EK874 board which is based on R8A774C0 SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).
This patch adds the required board support to boot Si-Linux EK874 board
based on R8A774C0 SoC.
DTS files apart from r8a774c0-ek874-u-boot.dts and r8a774c0-u-boot.dtsi
have been imported from Linux kernel 5.11 commit f40ddce88593
("Linux 5.11").
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
The HiHope RZ/G2H board from HopeRun consists of main board
(HopeRun HiHope RZ/G2H main board) and sub board(HopeRun
HiHope RZ/G2H sub board). The HiHope RZ/G2H sub board sits
below the HiHope RZ/G2H main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2H board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The HiHope RZ/G2N board from HopeRun consists of main board
(HopeRun HiHope RZ/G2N main board) and sub board(HopeRun
HiHope RZ/G2N sub board). The HiHope RZ/G2N sub board sits
below the HiHope RZ/G2N main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2N board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The HiHope RZ/G2M board from HopeRun consists of main board
(HopeRun HiHope RZ/G2M main board) and sub board(HopeRun
HiHope RZ/G2M sub board). The HiHope RZ/G2M sub board sits
below the HiHope RZ/G2M main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2M board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
-----BEGIN PGP SIGNATURE-----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=nIJc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210312' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Add WATCHDOG_RESET() in MTD framework and STM32 QSPI driver
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
Remove board_early_init_f() and board_late_init() callbacks for stm32
boards as the corresponding flags (CONFIG_BOARD_LATE_INIT and
CONFIG_BOARD_EARLY_INIT_R) are now disabled.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Check whether user has explicitly defined the mmc device to use
in mmc_get_env_dev() with CONFIG_SYS_MMC_ENV_DEV.
On STMicroelectronics boards the used mmc device for environment is
the instance of boot device provided by the ROM code; the mmc instance
is configured by alias in device tree. The used partition is defined in
device tree with u-boot,mmc-env-partition = "ssbl".
This patch allows to override this selection for the support of customer
boards without alias; for example when SDMMC1 is not used and ENV in
mmc0=SDMMC2, user can force the value: CONFIG_SYS_MMC_ENV_DEV = 0.
On STMicroelectronics boards, the current behavior is kept with
CONFIG_SYS_MMC_ENV_DEV = -1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add CONFIG_CMD_STM32PROG_SERIAL and CONFIG_CMD_STM32PROG_USB to
independently select the support of UART or USB communication for
STM32CubeProgrammer.
For serial boot over UART, user can deactivate CONFIG_CMD_STM32PROG_SERIAL
to use U-Boot console of binary loaded by UART (for board bring-up for
example).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since commit d5d726d3cc ("configs: stm32mp1: only support SD card after
NOR in bootcmd_stm32mp"), the stm32mp1 boards only support SD card after
NOR boot device, so the MTD partitions for nand0 or spi-nand0 are useless
(no need of "UBI" partition in nand0 or spi-nand0).
This patch removes these nand MTD update for nor boot and simplify nand0
and spi-nand0 support (remove the mtd_boot variable).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
board/emulation is the place for other QEMU targets like x86, arm,
riscv. Let's move the qemu-ppce500 board codes there.
List me as a co-maintainer for this board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This function is not called anywhere. Only fsl_ddr_sdram_size() is
necessary [1] for QEMU. Drop it.
[1] arch/powerpc/cpu/mpc85xx/cpu.c::dram_init()
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that we have switched to CONFIG_OF_CONTROL, and we can use the
env variable 'fdtcontroladdr' directly instead of creating one that
is duplicated.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
After U-Boot is relocated to RAM already, the previous temporary FDT
virtual-physical mapping that was used in the pre-relocation phase
is no longer needed. Let's delete the mapping.
get_fdt_virt() might be used before and after relocation, update it
to return different virtual address of FDT.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
By default the QEMU ppce500 machine connects a VirtIO NET to the
PCI controller, although it can be replaced to an e1000 NIC via
additional command line options.
Now that we have switched over to DM PCI, VirtIO support becomes
possible. This commit enables the support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present the board supports non-DM version PCI and E1000 drivers.
Switch over to use DM ETH and PCI by:
- Rewrite the PCI address map functions using DM APIs
- Enable CONFIG_MISC_INIT_R to do the PCI initialization and
address map
- Drop unnecessary ad-hoc config macros
- Remove board_eth_init() in the board codes
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The QEMU ppce500 target integrates 2 NS16550 serial ports. Switch
over to use the DM version of the driver by:
- drop unnecessary ad-hoc config macros
- add get_serial_clock() in the board codes
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The QEMU ppce500 machine generates a device tree blob and passes
it to U-Boot during boot. Let's enable OF_CONTROL with OF_BOARD
and provide board_fdt_blob_setup() in the board codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When QEMU originally supported the ppce500 machine back in Jan 2014,
it was created with a 1:1 mapping of PCI bus address. Things seemed
to change rapidly that in Nov 2014 with the following QEMU commits:
commit e6b4e5f4795b ("PPC: e500: Move CCSR and MMIO space to upper end of address space")
and
commit cb3778a0455a ("PPC: e500 pci host: Add support for ATMUs")
the PCI memory and IO physical address were moved to beyond 4 GiB,
but PCI bus address remained below 4 GiB, hence a non-identity
mapping was created. Unfortunately corresponding U-Boot updates
were missed along with the QEMU changes and the U-Boot QEMU ppce500
PCI support has been broken since then.
This commit makes the PCI (non-DM version) work again.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Alex's previous email address is no longer reachable.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Remove MAINTAINERS entries for
P3041DS_NAND_SECURE_BOOT_defconfig
and P5040DS_NAND_SECURE_BOOT_defconfig
as these configs support have been removed.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds support for more PMBus compatible devices to the NXP
drivers for its QorIQ family devices. At runtime, the voltage regulator is
queried over I2C, and the required voltage multiplier determined. This
change supports the DIRECT and LINEAR PMBus voltage reporting modes.
Previously, the driver only supported a few specific devices such as the
IR36021 and LTC3882, so this change allows the QorIQ series to be used
with a much larger variety of core voltage regulator devices.
checkpatch warning "Use if (IS_DEFINED (...))" was ignored to maintain
consistency with the existing code.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
After removal of MUX configuration there is no need to have extra rx51.h.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
This function is not used and was never called.
This board contains '#define CONFIG_SKIP_LOWLEVEL_INIT' because X-Loader
set everything up, including MUX configuration.
Also this MUX configuration is incorrect and does not match hardware.
So remove this dead, unused and broken code.
This change will decrease size of U-Boot binary.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Take over the plain 'tpm_...' functions for use by the new TPM API. Rename
all the TPMv1 functions so they are called from the API.
Update the TPMv1 functions so that they are called from the API. Change
existing users to use the tpm1_ prefix so they don't need to go through
the API, which might introduce uncertainty.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current implementation of reset_cpu() in the ns3 board code does not
archieve what it is supposed to (according to the comments), due to
a number of reasons:
1. The argument to reset_cpu() is _not_ actually passed from the
`reset` command, but is set to 0 in all call-sites (in this
specific case, see arch/arm/lib/reset.c). Thus, performing
different kinds of resets based on its value will not work as
expected.
2. Contrary to its documentation, the passed argument is not
interpreted, but a static `L3_RESET` define is used. The other
comment properly notes that this will always perform a L3 reset,
though.
3. The "parsing" of the static `L3_RESET` value is not even using the
upper and lower nibble as stated in the comment, but uses the last
two decimal digits of the value.
This is currently one of the only implementations left in U-Boot, which
make "use" of the value passed to reset_cpu(). As this is done under
false assumption (the value does not have any meaning anymore), it makes
sense to bring it into line with the rest and start ignoring the
parameter.
This is a preparation for removal of the reset_cpu() parameter across
the entire tree in a later patch.
Fixes: b5a152e7ca ("board: ns3: default reset type to L3")
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is a second lpddr configuration with 2GB of RAM, but this requires
different RAM timings, so in addition to adding the timing file, a
separate defconfig is necessary.
Signed-off-by: Adam Ford <aford173@gmail.com>
I would like to help supporting this board, so add myself
as a maintainer.
Now that the board has been converted to DM, also add
its devicetree in the MAINTAINERS files entry.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped splash screen support as this needs to be properly
converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Tested booting the Linux kernel from the SD card.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Remove the SATA support for now as the i.MX53 support has not
been added yet.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
- turris_mox: Enhancements, mostlly defconfig changes (Pali)
- pci-aardvark: Set Max Payload Size and Max Read Request Size
to 512 bytes (Pali)
- pci_mvebu: Minor cleanup and refactoring (Marek)
- Upgrade A38x DDR3 training to version 14.0.0 (Marek)
commit 6285efb8a118940877522c4c07bd7c64569b4f5f upstream.
the twin-die combined memory device should be treatened as X8
device and not as X16 one
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
[ - the default value for twin_die_combined is set to NOT_COMBINED for
all boards, as this was default behaviour prior this change ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is the last ARCH_MPC8569 board, remove that support
as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYDUezQAKCRDKSWXLKUoM
IbtgAJ9jZ+BOtwFaHR19TENC2DsHTINnnwCfSDn3fU0OFJRI0HD7pRxXr4xrb3M=
=Kr8x
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.04-rc3
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
Folder names corresponds to DT name. These boards have been renamed from
zc1275 to zcu1275 by commit shown below and this should be the part of that
commit.
Fixes: 420d446781 ("arm64: zynqmp: Rename zc1275 to zcu1275")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to clear reset reason register because it is protected by
PMUFW already which is reported when verbose log is enabled as:
pm_core.c@733 APU> No write permission to 0xFF5E0220
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Convert to driver model about power_key_pressed.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_VIDEO_MB862xx cannot be selected by any configuration.
So we can eliminate include/mb862xx.h.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Raspberry Pi Foundation released the new Compute Module 4 which we
want to detect, so we can enable Ethernet on it and know the correct
device tree file name.
Note that this sets the Ethernet option to true since the official CM4
IO board has an Ethernet port. But that might not be the case when using
custom ones.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Raspberry Pi Foundation released the new RPi400 which we want to
detect, so we can enable Ethernet on it and know the correct device tree
file name.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
When RPi4 is booted from USB Mass Storage, the firmware reports 947MiB of
the ARM memory (948 in case of the standard SD-card boot). This value is
not MMU_SECTION_SIZE aligned, so the dram_bank_mmu_setup() skips mapping
of the last 1MiB. This later causes u-boot in ARM 32bit mode to freeze,
because it relocated itself into that unmapped memory and fails to
execute.
Fix this by limiting the size of the first bank to the multiple of
MMU_SECTION_SIZE.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
As this is the last SH4A board, remove that support as well.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Patch-cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Patch-cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Chris Packham <judge.packham@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lauri Hintsala <lauri.hintsala@silabs.com<mailto:lauri.hintsala@silabs.com>>
Signed-off-by: Tom Rini <trini@konsulko.com<mailto:trini@konsulko.com>>
Both Zynq and ZynqMP can show silicon versions in SPL boot flow. It is
useful to be aware.
The patch is also fixing possition of these bits on ZynqMP.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix bug introduced by commit listed below. It is for cases where Versal or
ZynqMP don't have DDR mapped. Later SPL was also excluded by
commit a672b9871b ("xilinx: common: Do not touch
CONFIG_XILINX_OF_BOARD_DTB_ADDR in SPL").
Fixes: 506009fc10 ("xilinx: common: Change macro handling in board_fdt_blob_setup()")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the ADC channel 1 to check the hardware revision of the board and
detect the N2 vs. N2+ and the C4 vs. HC4 variants. Each of them use
different dtb file, so adjust fdtfile environment variable to the
detected variant.
The ADC min/max values for each variant are taken from the vendor code,
adjusted to the 12-bit ADC driver operation mode (vendor code use 10-bit
mode).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
- Espressobin: Set default env values at runtime (Pali)
- Espressobin: Set the maximum slave SPI speed to 40MHz (Pali)
- theadorable: PCIe test code enhancement and early deemphasis
enabling (Stefan)
- pci_mvebu: Disable config access to PCI host bridge ports (Stefan)
- mv_sdhci: parse device-tree entry (Baruch)
Cleanup, move the declarations to keymile/common.h instead declaring them
per-board config.h
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Replace instances of sprintf()/set_env() for setting hexadecimal
values with set_env_hex().
In set_km_env() the "pram" variable was set to an hexadecimal
value, while initr_mem() expects an unsigned decimal, so use
set_env_ulong() instead.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Take into account SDRAM_BASE address when calculating pnvramaddr and
varaddr offsets.
Up to now Keymile designs had SDRAM_BASE equal to zero and the offsets
where calculated correctly, this fix is for the upcoming designs that
have SDRAM_BASE different then zero.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add show_qrio function to print chip id and revision information.
There are already multiple QRIO chip versions available and the upcoming
designs may want to show used version.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch is fixing qrio driver compilation for ARM architecture:
- It includes asm/io.h for in_/out_ access
- It use correct names for set/clear_bits as defined in linux/bitops.h
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable SATA support. Although not supported by the usual SATA pins on
the SMARC baseboard connector, SATA mode is supported on a PCIe lane.
This way one can use a mSATA card in a Mini PCI slot.
We need to invert the received data because in this mode the polarity of
the SerDes lane is swapped. Provide a fixup in board_early_init_f() for
the SPL. board_early_init_f() is then not common between SPL and u-boot
proper anymore, thus common.c is removed, as it just contained said
function.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Although this variant has two external network ports, they are not (yet)
supported by the bootloader because they are connected via an internal
network switch. Otherwise its the same as the other variants.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This variant has one network port connected via RGMII and doesn't have
any TSN capabilities out-of-the-box. Instead it has all four SerDes
lanes available for customer use.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Testing has shown, that the quality of the PCIe signals and also the
stability of correct link establishment on the 2 PCIe ports is better,
when the deemphasis bit is set in the PCIe config register.
This needs to be done very early, even before the SERDES setup code is
run. This way, the first link will already be established with this
setup.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the board specific "pcie" U-Boot command to not only
check for PCIe device existance but also for the correct link speed
and width that has been established. This cmd can be used by U-Boot
scripts for automated testing, if the PCIe setup is correct. Meaning,
that all PCIe devices are correctly detected and the link speed and
width is corrent.
Signed-off-by: Stefan Roese <sr@denx.de>
On Espressobin board are MAC addresses stored in U-Boot env area. Therefore
they are not present in default_environment[] array constructed at compile
time.
This change puts permanent MAC addresses into default_environment[] array
at board runtime. Espressobin board has enabled DEFAULT_ENV_IS_RW option
and therefore can modify this array.
This change ensure that 'env default -a' does not delete permanent MAC
addresses from Espressobin env storage area.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
On Espressobin board value for $fdtfile cannot be determined at compile
time and is calculated at board runtime code. This change uses a new option
DEFAULT_ENV_IS_RW to allow modifying default_environment[] array at runtime
and set into it correct value.
This change also ensure that 'env default -a' set correct value to $fdtfile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
The Beacon EmbeddedWorks kit is based on the R8A774E1 SoC also
known as the RZ/G2H.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi. It shares much of the same design as
the RZ/G2M and RZ/G2N dev kits.
Signed-off-by: Adam Ford <aford173@gmail.com>
The Beacon EmbeddedWorks kit is based on the R8A774B1 SoC also
known as the RZ/G2N.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi. It shares much of the same design as
the RZ/G2M dev kit.
Signed-off-by: Adam Ford <aford173@gmail.com>
These ops are missing at present which is not permitted. Add an empty
operation struct.
Note: If the uclass requires operations then the drivers should provide
them. Otherwise, checking for missing operations must be done in every
uclass operation, so it adds to code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
This drops assigning bi_arch_number on LEGO MINDSTORMS EV3. This board
never had its own unique number and since we are using device tree,
we no longer need to pass an arch number to Linux.
Signed-off-by: David Lechner <david@lechnology.com>
This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.
Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).
Signed-off-by: David Lechner <david@lechnology.com>
Move twl4030_power_mmc_init() from board_mmc_power_init() to misc_init_r()
and disable CONFIG_SYS_MALLOC_F. Otherwise U-Boot cannot initialize MMC.
Also disable CONFIG_CMD_SLEEP CONFIG_DM_DEVICE_REMOVE CONFIG_MMC_VERBOSE to
free some space.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
addr was delcared as fdt_addr_t which is now a 64-bit address.
In a 32-bit build, this causes the following warning seen when
building ax25-ae350.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast addr with uintptr_t.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This change extends previous commit 061c6d1b23 ("arm: mvebu: Espressobin:
Detect presence of emmc at runtime") and when emmc is not present then emmc
is removed from U-Boot DM and corresponding slot is disabled. Therefore on
Espressobin board without soldered emmc, state of emmc hw should be same as
if emmc was disabled in DTS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
SATA and UART ClearFog imaages are not buildable as ENV_SECT_SIZE is not defined
set values for both possible targets
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.
The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This port is needed for communication with PMIC. SPL uses it to set DRAM
voltage on H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The #ifdef CONFIG_xxxPWR conditionals were not working as expected, as
string Kconfig symbols are always "defined" from the preprocessor's
perspective. This lead to unnecessary calls to the GPIO routines, but
also always added a half a second delay to wait for a SATA disk to power
up. Many thanks to Peter for pointing this out!
Fix this by properly comparing the Kconfig symbols against the empty
string. strcmp() would be nicer for this, but GCC does not optimise this
away, probably due to our standalone compiler switches.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi WinPlus
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
dts file is taken from Linux 5.11-rc1 tag.
The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.
DT file is taken from Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
The mt7620_rfb board supports integrated 10/100M PHYs plus two external
giga PHYs. It also has 8MB SPI-NOR, mini PCI-e x1 slot, SDHC and USB.
The mt7620_mt7530_rfb boards supports an external MT7530 giga switch and a
16MB SPI-NOR flash.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The previous macro was off by one bit and so we were getting a ddr
size which was twice the real size. This commit refactors the macro so
it returns the right size in _bytes_ and modifies the printf call so the
size is still printed in MiB.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
This patch converts the dart6ul ethernet support to DM_ETH and cleans
up the legacy ethernet code. The clean up, more specifically:
* moves the fec2 node and pin definition to the carrier board DTS
since the phy associated with it is on the carrier board and not on
the SoM;
* add the reset pin associated to each phy;
* separate the ethernet, mdio and reset pins of each fec so that they
are easier to reference;
* add clock properties to the phy nodes since they are connected to the
50Mhz ENET[12]_TX_CLK clock of the SoC;
* remove CONFIG_BOARD_EARLY_INIT_F since the function is now empty.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg
The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value
"/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg
The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value "
/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use
CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Giant board is a tiny SBC based on the Adafruit Feather form factor,
created by groboards it contains a SAMA5D2 processor (SAMA5D27),
128 MB of RAM and a microSD card for storage.
Signed-off-by: Greg Gallagher <greg@embeddedgreg.com>
This adds support for the NanoPi R2S from FriendlyArm.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
This hook is used in full U-Boot that's why there is no reason to touch
this location from SPL. The hook was introduced for QEMU usage but none is
really running SPL on QEMU that's why it shouldn't break any usecase.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove ifdef logic which is handled by preprocessor and move it link time
optimization to get full compile code coverage.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For systems which has both sdhci controllers enable it is worth to export
bootseq number for variables. Then the variable can be used in custom
scripts to tune logic for OS.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add the default configuration for the AST2600 EVB.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Add low level platform initialization for the AST2600 SoC.
The 2-stage booting with U-Boot SPL are leveraged to support
different booting mode.
However, currently the patch supports only the booting from
memory-mapped SPI flash.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Our kirkwood device embeds a USB host controller that is now used
on some boards. This enables the support of USB and the corresponding
driver.
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds Microchip MPFS Icicle Kit support. For now, only
NS16550 Serial, Microchip clock, Cadence eMMC and MACB drivers are
enabled. The Microchip MPFS Icicle defconfig by default builds
U-Boot for S-Mode because U-Boot on Microchip PolarFire SoC will run
in S-Mode as payload of HSS + OpenSBI.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
This enables configs necessary for using SPI. The environment is saved to
the very end of SPI flash. This is unlikely to be overwritten unless the
entire flash is reprogrammed.
This also supplies a default bootcommand. It loads an image and device tree
from the first partition of the MMC. This is a minimal/least effort
bootcmd, so suggestions (especially in the form of patches) are welcome. I
didn't set up distro boot because I think it is unlikely that any
general-purpose linux distros will ever be ported to this board.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Chrstopher Obbard <obbardc@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/+yLkACgkQ4rK92eCq
k3X/Fgf/d/11WyQrVzvpr+nN+4Wl7J+ASmoUz0yKa6ri+lbvhLgh+JXbCRKgRPWu
vNnI07pSoX/QeaMpGBU8Ztg/Onb9/pvffz4WMk1411GoyCpDFuuK3cVSIoqkPfu+
XmgSX0u4BXtve1+ZdWfVBWXawUSEDMmGR3tmz1708c/s/oYpnVeRDcqiqzJ94cWE
yt+SpMPVqMUVQ/rAGkE8ToSMxX7FusEa7SvCg4U2ikoRWs3kPpr/73+tRWlmgGxL
sW8SXSKiOmFyheSBx3d2B9n00kDYTTrQmbW9hlMilZmji7CwZYxgTCMdX0x4DeFP
RDajT2Yju1JmeM+Z8+Ke2tupzvy6QA==
=oK8C
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210113' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
There shouldn't be a need to use loadables propertyn because u-boot can be
pointed by firmware property. This change should also speedup boot process
because loadables property is list of strings which code is going through.
On the other hand firmware can just point to one image.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
USB-C power supply which are Power Delivery compliant (USB-PD) are able
to provide different voltage/current (for example 5V/3A 9V/3A 12V/2.25A...)
In this case, the power supply need to negotiate the voltage/current to
use with the device using CC1/CC2 USB-C signals.
If this negotiation occurs during ADC measurement (done also on CC1/CC2
USB-C signals) some ADC acquisition can be corrupted which cause wrong
power supply current detection.
To avoid this, the power supply current detection algorithm is updated
as following:
- perform an ADC measurement, if a 3A current is detected, continue the
boot process.
- else, wait 20ms (max tPDDebounce duration) to ensure that USB-PD
negotiation is done and perform another ADC measurement.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove board_mmc_init function.
It will be probed with driver-model.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
- DM support for OMAP PWM backlight
- USB host mode support for AM654
- Minor SPI fixes
- Add support k2g ice board with 1GHz silicon
- Fix GTC programming for K3 devices
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/8S/0cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKFkB/9NBJq/+sgHZXRaMlAu
ULNwOPoNsQxHQGwF88B1lC+H8LJjM+2gJ8MfJdWvHNlcSdtJjbWk0aQL+5LKSlyz
G7l3BZ+AIYMOeTXay5mNUKnekXIr7c8tLoX8FH/Ih+bHFPt57qL0bbfznV66UCOp
/o/yM8daPa9Kx1vPEpT2dC9bYXLXeQv6R+RMxwoc4Bk+R3OK7zoZ3Wdx0q9HvBwj
iWHM49X2fBqqi5RS+ZI37AUzi8iysD3fOq0kWTJcCNaci8i8RZdzSyoaDuXhA63I
EZJ7v9fUkW/bwTONVE9n2BX4xF9X/6R7P46l9dQISXAxsOBwsNRQPt8Ro7mCoc4K
392o
=LIK7
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2021.04 cycle
This feature set includes the new board SAMA7G5 EK, the new evaluation
kit for Microchip AT91 SAMA7G5 SoC . The current board support includes
two configurations for booting from eMMC (SDMMC0), SD-Card (SDMMC1), and
support for two Ethernet interfaces.
Fix reading built-in ethernet MAC address from efuse
NOTE: MAC is stored in ASCII format, 1bytes = 2characters by 0 offset
if mac from efuse not valid we use meson_generate_serial_ethaddr
NOTE: remake odroid-n2.c from Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Artem Lapkin <art@khadas.com>
[narmstrong: remove MAC print & spurious new endline]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
With support for other clock drivers, the potentially supported CDCE913
device can no longer be probed without specifying its DT node name.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
It has been observed that setting SERDES0 lane mux to USB prevents USB 2.0
operation on USB0. Setting SERDES0 lane mux to non-USB when USB0 is used in
USB 2.0 only mode solves this issue. However, for USB3.0+2.0 operation this
issue is not present.
Implement this workaround by writing 1 to LANE_FUNC_SEL field in
CTRLMMR_SERDES0_CTRL register.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Some Bluetooth controllers, like the BCM4345C5 of the Orange Pi 3,
ship with the controller default address.
Add a config option to fix it up so it can function properly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Refactor setup_environment() so we can use the created sid for a
Bluetooth address too.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For the sake of consistency (*) and order of initialization, i.e.
after we have got the ethernet address, interrupt and timer initialized,
try to initialize USB ethernet gadget.
*) for example, zynqmp uses same order.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
PineCube is an IP camera development kit released by Pine64.
It comes with the following compoents:
- A mainboard with Sochip S3 SoC, a 16MByte SPI Flash, AXP209 PMIC,
a power-only microUSB connector, a USB Type-A connector, a 10/100Mbps
Ethernet port and FPC connectors for camera and daughter board.
- An OV5640-based camera module which is connected to the parallel CSI
bus of the mainboard.
- A daughterboard with several buttons, a SD slot, some IR LEDs, a
microphone and a speaker connector.
As the device tree is synchronized in a previous commit, just add it to
Makefile, create a new MAINTAINER item and provide a defconfig.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Detect eMMC or SD card boot on Odroid-C4/N2 and Khadas VIM3(l) boards and
report proper MMC device for the environment loading code. This allows to
automatically load and store environment variables on the FAT partition
or RAW offset of the MMC device without the need to use different
configurations on eMMC and SD card.
To use this feature with environment stored on FAT partition, one has to
specify an empty device part (i.e. ":1" for the first partition) in
CONFIG_ENV_FAT_DEVICE_AND_PART to let the code to set the device to the
value returned by mmc_get_env_dev() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Copied from Odroid N2. Add myself as maintainer.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the board specific code for reading built-in ethernet MAC address
from efuse.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Update the device matrix and add build instructions.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: added wetek-core2.rst to q200 MAINTAINERS and added blank lines to fix build]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add a config for the WeTek Core2, largely based on the VIM2 config.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: added wetek-core2_defconfig to q200 MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SoC revision to environment. This can be useful to select the
correct device tree at runtime (N2/N2+).
Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the Amlogic based libretech cc version 2.
As version 1, it is based on the s905x SoC.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: Fixed libretech-cc.rst bullet points]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On the imx287 pin GPMI_WRN (GPIO0_25) no PullUP is available that can be
enabled.
To get the same behavior for both boot select pins (i.e. GPIO0_2{35})
disable pull UPs on both.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Obtain two MAC addresses from the two EEPROMs and configure the two
available Ethernet interfaces accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add new config for storing environment from sdmmc0.
Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.
The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)
It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.
Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update various drivers to use of_match_ptr() and to avoid including debug
strings in TPL. Omit the WiFi driver entirely, since it is not used in
TPL.
This reduces the TPL binary size by about 608 bytes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Lower case should be used for function names. Update this driver and its
callers accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Typedefs should not be used in U-Boot and structs should be lower case.
Update the code to use struct ns16550 consistently.
Put a header guard on the file while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It looks like that i2c bus lot of times timeout on some units. Prior
migration to CONFIG_DM_I2C i2c speed was set to CONFIG_SYS_OMAP24_I2C_SPEED
value which was 100000. Lower speed fixes timeout problems, so change speed
back to its previous value.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 8d8c181703 ("Nokia RX-51: Convert to CONFIG_DM_I2C")
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
All Xilinx SoCs have repository location filled already but boards are
covered by different fragment which is missing this link.
The patch is extending description with adding proper link to the same
repository.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Building xilinx_zynq_virt_defconfig fails on origin/next as reported by
GCC 10.2 (as provided by Debian Bullseye):
CC board/xilinx/common/fru_ops.o
board/xilinx/common/fru_ops.c: In function ‘fru_capture’:
board/xilinx/common/fru_ops.c:173:8:
error: array subscript 284 is outside array bounds of
‘struct fru_table[1]’ [-Werror=array-bounds]
173 | limit = data + sizeof(struct fru_board_data);
| ~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
board/xilinx/common/fru_ops.c:17:18: note: while referencing ‘fru_data’
17 | struct fru_table fru_data __section(.data);
| ^~~~~~~~
When using sizeof(struct fru_board_data) to find the end of the structure
you should add it to the start of the structure.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set script_offset_nor env variable using CONFIG_BOOT_SCRIPT_OFFSET
and nor flash start address to keep bootscript offset configurable.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for authenticating uefi capsules. Most of the signature
verification functionality is shared with the uefi secure boot
feature.
The root certificate containing the public key used for the signature
verification is stored as part of the device tree blob. The root
certificate is stored as an efi signature list(esl) file -- this file
contains the x509 certificate which is the root certificate.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
The dfu framework uses the dfu_alt_info environment variable to get
information that is needed for performing the firmware update. Add
logic to set the dfu_alt_info for the qemu arm64 platform to reflect
the two mtd partitions created for the u-boot env and the firmware
image. This can be subsequently extended for other qemu architectures
which need this variable set.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Add support for setting the default values for mtd partitions on the
platform. This would be used for updating the firmware image using
uefi capsule update with the dfu mtd backend driver.
Currently, values have been defined for the qemu arm64 platform, with
default values defined for the mtd partitions based on the NOR
flash. This can be subsequently extended for other qemu architectures
which need mtdparts set.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
On the qemu arm platform, the virtio devices are initialised in the
board_init function, which gets called before the initr_pci. With
this sequence, the virtio block devices on the pci bus are not
initialised. Move the initialisation of the virtio devices to
board_late_init which gets called after the call to initr_pci.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
The dart6ul has an i2c eeprom at 0x50 which contains, among other
things, the manufacturing/revision/options info of the SoM. This patch
replaces the current checkboard() implementation with a more
exhaustive one based on the content of the eeprom.
Since this code uses the new driver model, some changes were also
required in the DTS to make the nodes related to i2c available before
relocation.
This code was inspired from the supported u-boot code from Variscite
which can be found here:
https://github.com/varigit/uboot-imx/tree/imx_v2018.03_4.14.78_1.0.0_ga_var02
New output example:
Board: PN: VSM-6UL-705B, Assy: AS1812142257, Date: 2019 Feb 17
Storage: eMMC, Wifi: yes, DDR: 1024 MiB, Rev: 2.4G
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Hand over maintainership of Toradex SoMs (that I was responsible of) to
Oleksandr because of my resignation from Toradex, as such I will
have no immediate involvement with these modules and as a result not
able to continue maintaining these boards.
CC: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The current PHY rework does the following things:
1. Configure 125MHz clock
2. Setup the TX clock delay (RX is enabled by default),
3. Setup reserved bits to avoid voltage peak
The clock delays are nowadays already configured by the
PHY driver (in ar803x_delay_config). The code for that
can simply be dropped. The clock speed can also be
configured by the PHY driver by adding the device tree
property "qca,clk-out-frequency".
What is left is setting up the undocumented reserved bits
to avoid the voltage peak problem. I slightly improved its
documentation while updating the board's PHY rework code.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of hardcoding index magic numbers in the board code,
also rely on board_fit_config_name_match choosing the right
config for the fitImage containing the kernel.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
After the conversion to device tree the board information becomes
redundant:
Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board
Board: MX6-SabreSD
Remove the printing of the board information.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Before executing code that we have loaded from a file we need to flush the
data cache and invalidate the instruction flash.
Implement functions flush_cache() and invalidate_icache_all().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
DM is the modern default approach for the drivers in U-Boot.
It also allows to configure code via Device Tree.
Move Intel Edison to use DM_USB_GADGET and drop hard coded values.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The platforms based on Intel Tangier may have different requirements
how to create bootloader bundle to supply to a device. Currently
the BINMAN approach is for Intel Edison only.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Initialize variable 'i2caddress' in adjust_vdd() to zero
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix a bug that failed to read/write eeprom on ls1021atsn
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
=cgbE
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Check whether user has explicitly defined device and partition where
environment file will be located before using 'auto' i.e. bootable
partition
Voids the need to set such partition as bootable to work with the
'dev:auto' tuple
Signed-off-by: Manuel Reis <mluis.reis@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
threshold configuration (Joshua)
Try to initialize emmc in board_late_init() and if it fails then we know
that emmc device is not connected.
This allows to use in U-Boot just one DTS file for all Espressobin variants
and also to correctly set fdtfile env variable for Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Add Luka Perkov to Puzzle-M801 BOARD MAINTAINERS.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Add implementation of board_mem_get_layout for overriding the memory
layout.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Implement board_phys_sdram_size() to automatically detect Verdin iMX8M
Mini DualLite 1GB vs. Verdin iMX8M Mini Quad 2GB.
Note: This only works if we keep using similar RAM chips!
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Now with them first Verdin iMX8M Mini DualLite modules in for bring-up
we got clarity how is_cpu_type() actually behaves.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Enable PCA9450 i2c level translator, as this is used for the
on module ADC.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
And select the correct devicetree accordingly by setting the variant
environment variable.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
V1.1A HW switched the PMIC from BD71837 to PCA9450.
- Disable combined DVS in PCA9450_BUCK123_DVS.
- Increase DDR Voltage to 0.95V as we use a 1.5GHz RAM.
- Configure WDOG_B behaviour.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
add the dts file to the MAINTAINERS entry
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Set `bootcause' from b850v3 power management watchdog status.
Boot cause "REVERT" is no longer used, remove it.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use VPD product ID instead of confidx, so that we can easily reuse the
product ID defines and avoid some magic numbers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove pinmux defines, that are no longer used after
converting the code to devicetree.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Commit f692b479f0 changed the VPD partition name from "vpd" to
"vpd@0". Fix the VPD reader code to use the new name, so that
the VPD code keeps working.
Fixes: f692b479f0 ("i2c: eeprom: Use reg property instead of offset and size")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
Use gpio_early_init_uart() function to disable RS232 serial transceiver
ForceOFF# pins on Iris.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Avoid UART input from floating RX pins on UARTB and UARTC (Colibri T30)
and UARTB, UARTC and UARTD (Apalis T30).
Note: Floating pins may cause spurious break conditions potentially
interrupting U-Boot's autoboot.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix SPI1 and UART2/3 resp. UARTB/C pinmuxing.
Note: The former was illegally muxing multiple SoC balls onto the same
internal SoC signal which caused rather strange behaviour regarding
the RS232 serial transceiver ForceOFF# pins as available on Iris.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add pinmuxing comment stating that TRISTATE means the output driver is
tri-stated and INPUT means the input driver is enabled vs. OUTPUT where
it is disabled.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Address most of the checkpatch issues we found in km_arm and common km
code.
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Update kernel load address for FIT examples to avoid relocation:
- Kernel example uses Image.gz with U-Boot gzip decompression
at final kernel location 0x0xC0008000.
- Copro example loads zImage at a correct location (0xC4000000),
to avoid zImage relocation before decompression by kernel code.
An other solution to avoid zImage relocation is to align
the kernel load and entry address with the real location in FIT
(the relocation of zImage is skipped in U-Boot bootm command for
identical address) but it is less flexible because this offset
depends on FIT content:
For example:
## Loading kernel from FIT Image at c2000000 ...
Using 'ev1' configuration
Trying 'kernel' kernel subimage
Description: Linux kernel
Created: 2020-10-22 9:08:32 UTC
Type: Kernel Image
Compression: uncompressed
Data Start: 0xc20000cc
The kernel offset in FIT is 0xCC in FIT and zImage is decompressed at
0xC0008000 by kernel code:
kernel {
description = "Linux kernel";
data = /incbin/("zImage");
type = "kernel";
arch = "arm";
os = "linux";
compression = "none";
load = <0xC20000cc>;
entry = <0xC20000cc>;
hash-1 {
algo = "sha1";
};
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove the update of the MTD partitions in kernel device tree
for serial boot (USB / UART), and the kernel will use the MTD
partitions define in the loaded DTB because U-Boot can't known the
expected flash layout in this case.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
If customs fields in board area are used it will likely go over allocated
space in struct fru_board_data. That's why calculate limit of this
structure to make sure that different data is not rewritten by accident.
When limit is reached stop to record fields.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
capture variable is bool which is just one byte and it is just causing
unaligned accesses. Better to have it as last entry in the structure.
It also simplify offset calculation for initial header copy.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to use this file anymore. Include it in main config file
and simplify logic based on it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Also change back SYS_MEMTEST_END to 0x00f00000. 0xe00000 was wrong and
introduced due to the global Kconfig migration of this option in u-boot.
CC: Heiko Schocher <hs@denx.de>
CC: Tom Rini <trini@konsulko.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Instead of using an hard coded address, make use of an
already defined address for importing the environment
for ramfs and nfs boot. This allows boards having different
mapping to use the same code.
CC: Heiko Schocher <hs@denx.de>
CC: Tom Rini <trini@konsulko.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Re-submitted because of missing description and signed-off.
flags reset in board_init caused bugs when executing command like editenv
because the reallocated flag was lost.
Tested-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
Signed-off-by: Arnaud Aujon Chevallier <arnaud@intelibre.fr>
Allow attaching a virtual SATA disk to QEMU RISC-V by implying
AHCI, AHCI_PCI, CMD_SCSI, DM_SCSI, PCI_INIT_R, SCSI, SCSI_AHCI.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Sort implied options in BOARD_SPECIFIC_OPTIONS in the same sequence as in
.config.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The reference design of Allwinner V3 series uses an
AXP203 or AXP209 PMIC attached to the I2C0 bus of the SoC, although the
first community-available V3s board, Lichee Pi Zero, omitted it.
Allow to introduce support for the PMIC on boards with it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The PinePhone is a smartphone produced by Pine64, with an A64 SoC,
2 or 3 GiB LPDDR3 RAM, 16 or 32 GiB eMMC, 720x1440 MIPI-DSI panel,
and Quectel EG25-G modem.
There are two main board revisions: 1.1 for early adopters, and 1.2
for mass production. Since there is code to detect the board revision
at boot, one config/image can support both boards.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Previously, fdtfile was always the value in CONFIG_DEFAULT_DEVICE_TREE.
This meant that, regardless of the DT chosen by SPL (either by changing
the header in the image or by the selection code at runtime), Linux
always used the default DT.
By using the name from the SPL header (which, because of the previous
commit, always matches the DT used by U-Boot proper), Linux also sees
the same board as U-Boot/SPL, even if the boot script later loads a DT
from disk.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: remove no longer needed CONFIG_SPL_LOAD_FIT guards]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This overwrites the name loaded from the SPL image. It will be different
if there was previously no name provided, or if a more accurate name was
determined by the board variant selection logic. This means that the DT
name in the SPL header now always matches the DT appended to U-Boot.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: move function under CONFIG_SPL_LOAD_FIT guard]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There are two different publicly-released revisions of the PinePhone
hardware, versions 1.1 and 1.2; and they need different device trees.
Since some GPIO pins were rerouted, we can use that to distinguish
between them.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Instead of using an entirely separate matching algorithm, simply update
the name of the DT we want to match. Enabling this logic does not depend
on the FIT config name, only on the initial guess of the board name.
Importantly, the initial guess must be "sun50i-a64-pine64-plus", because
otherwise the logic would trigger when "sun50i-a64-pine64-lts" was
written to the SPL header.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This moves the validity checking and typecasts all to one place away
from the string comparison logic, and it detangles the compile-time
and runtime control flow.
The new helper will also be used by U-Boot proper in a future commit.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: protect new function with CONFIG_SPL_LOAD_FIT]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The variable "cmp_str" always leaves me wondering if it is the DT name
of the current board (yes) or DT name in the FIT config entry (no).
In preparation for expanding the functionality here, rename it to
something that obviously means "this is the DT name we are looking for".
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
