Jarrold Wen noticed that the generic PHY code always matches
under the current implementation. Change it so the first match
wins, and *only* unknown PHYs trigger the generic driver
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix a bug in the Marvell 88e1145 PHY init code in the TSEC driver
where the reset was being done after the errata code instead of
before.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
FSL PCIe block has extended cfg registers in the 100 and 400 range.
For example, to read the LTSSM register: pci display <busn>.0 404 1
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Ensure hose->current_busno is not less than first_busno. This fixes
broken board code which leaves current_busno=0 when first_busno is
greater than 0 for the cases with multiple controllers.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Enabled cache in cpu_init_f() for faster flash to mem allocation. Updated cache handling in start.S. Applied cache invalidate in fec_send() and fec_recv(). Added CFG_UNIFY_CACHE for CF V3 only.
Signed-off-by: TsiChung <tcliew@Goku.(none)>
Renamed mcfserial.c to mcfuart.c. Modified Makefile for mcfuart.o from mcfserial.o. Replace immap_5329.h and m5329.h to immap.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This is a cosmetic only changes submission.
It affects files relevant to bcm570x driver.
the commands used to generate this change was
cd drivers
Lindent -pcs -l80 bcm570x.c bcm570x_lm.h bcm570x_mm.h tigon3.c tigon3.h
The BMW target (the only one using this chip so far) builds cleanly, the
`before and after' generated object files for drivers/bcm570x.c and
drivers/tigon3.o are identical as reported by objdump -d
Signed-off-by: Vadim Bendebury <vbendeb@google.com>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
This patch added USB PCI-OHCI chips support, interrupt pipe support
and usb event poll support. For supporting the USB interrupt pipe, the
globe urb_priv is moved to purb in ed struct. Now, we can process
several urbs at one time. The interrupt pipe support codes are ported
from Linux kernel 2.4.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Using some (very) slow USB keys cause the USB host controller buffers
are not ready to be read by the CPU so we need an extra delay before
reading the USB storage data.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
This patch updates the nand_ecc code to the latest Linux version.
The main reason for this is the more compact code. This makes
it possible to include the ECC code into the NAND bootloader
image (NAND_SPL) for PPC4xx.
Signed-off-by: Stefan Roese <sr@denx.de>
For all practical u-boot purposes, TSECs don't differ throughout the
mpc8[356]xx families; reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Bridge, ICH-5, ICH-6 and ICH-7.
Implementation:
1. Code is divided in to two files. All functions, which are
controller specific are kept in "drivers/ata_piix.c" file and
functions, which are not controller specific, are kept in
"common/cmd_sata.c" file.
2. Reading and Writing from the S-ATA drive is done using PIO method.
3. Driver can be configured for 48-bit addressing by defining macro
CONFIG_LBA48, if this macro is not defined driver uses the 28-bit
addressing.
4. S-ATA read function is hooked to the File system, commands like
ext2ls and ext2load file can be used. This has been tested.
5. U-Boot command "SATA_init" is added, which initializes the S-ATA
controller and identifies the S-ATA drives connected to it.
6. U-Boot command "sata" is added, which is used to read/write, print
partition table and get info about the drives present. This I have
implemented in same way as "ide" command is implemented in U-Boot.
7. This driver is for S-ATA in native mode.
8. This driver does not support the Native command queuing and
Hot-plugging.
Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
If a PCI IDE card happens to get a zero address assigned to it, the Linux IDE
core complains and IDE drivers fails to work. Also, assigning zero to a BAR
was illegal according to PCI 2.1 (the later revisions seem to have excluded the
sentence about "0" being considered an invalid address) -- so, use a reasonable
starting value of 0x1000 (that's what the most Linux archs are using).
Alternatively, one might have fixed the calls to pci_set_region() individually
(some code even seems to have taken care of this issue) but that would have
been a lot more work. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Stefan Roese <sr@denx.de>
the v_mac variable in the smc91111 driver is declared as a signed char ...
this causes problems when one of the bytes in the MAC is "signed" like 0xE0
because when it gets printed out, you get a display like:
0xFFFFFFE0 and that's no good
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In case that there is no memory based bad block table available the
function nand_block_checkbad() in drivers/mtd/nand/nand_base.c will call
nand_block_bad() directly. When parameter 'getchip' is set to zero,
nand_block_bad() will not right shift the offset to calculate the
correct page number.
Signed-off-by: Thomas Knobloch <knobloch@siemens.com>
Signed-off-by: Stefan Roese <sr@denx.de>
There were a few theoretical possibilities that the compiler might
optimize away DMA descriptor reads and/or writes and thus cause
synchronization problems with the hardware. Insert barriers where
we depend on reads/writes actually hitting memory.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
When bringing up u-boot on new boards, PHY support sometimes gets
neglected. Most PHYs don't really need any special support,
though. By adding a generic entry that always matches if nothing
else does, we can provide support for "unsupported" PHYs for the
tsec.
The generic PHY driver supports most PHYs, including gigabit.
Signed-off-by: David Updegraff <dave@cray.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
* Add support to the Makefile
* Add 8544 configuration support to the tsec driver
* Add 8544 SVR numbers to processor.h
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Driver for the Atmel MACB on-chip ethernet controller.
This driver has been tested on the ATSTK1000 board with a AT32AP7000
CPU. It should probably work on AT91SAM926x as well with some minor
modifications.
Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Rewrite the resource management code (i.e. I/O memory, clock gating,
gpio) so it doesn't depend on any global state. This is necessary
because this code is heavily used before relocation to RAM, so we
can't write to any global variables.
As an added bonus, this makes u-boot's memory footprint a bit smaller,
although some functionality has been left out; all clocks are enabled
all the time, and there's no checking for gpio line conflicts.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Fix empty i2c reads/writes, i2c_write(0x50, 0x00, 0, NULL, 0)
which is used to se if an slave will ACK after receiving its address.
Correct i2c probing to use this method as the old method could upset
a slave as it wrote a data byte to it.
Add a small delay in i2c_init() to let the controller
shutdown any ongoing I2C activity.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
The problem is not gcc4 but the code itself. The BD_STATUS() macro can't
be used for busy-waiting since it strips the 'volatile' property from
the bd variable. gcc3 was working by pure luck.
This is a follow on patch to "Fix the UEC driver bug of QE"
I've redone the SBC8349 support to match git-current, which
incorporates all the MPC834x updates from Freescale since the 1.1.6
release, including the DDR changes.
I've kept all the SBC8349 files as parallel as possible to the
MPC8349EMDS ones for ease of maintenance and to allow for easy
inspection of what was changed to support this board. Hence the SBC8349
U-Boot has FDT support and everything else that the MPC8349EMDS has.
Fortunately the Freescale updates added support for boards using CS0,
but I had to change spd_sdram.c to allow for board specific settings for
the sdram_clk_cntl (it is/was hard coded to zero, and that remains the
default if the board doesn't specify a value.)
Hopefully this should be mergeable as-is and require no whitespace
cleanups or similar, but if something doesn't measure up then let me
know and I'll fix it.
Thanks,
Paul.
The patch prevents the GCC tool chain from striping useful code for
optimization. It will make UEC ethernet driver workable, Otherwise the
UEC will fail in tx when you are using gcc4.x. but the driver can work
when using gcc3.4.3.
CHANGELOG
*Prevent the GCC from striping code for optimization, Otherwise the UEC
will tx failed when you are using gcc4.x.
Signed-off-by: Dave Liu <daveliu@freescale.com>
As suggested by Grant Likely this patch enables the Xilinx SystemACE
driver to select 8 or 16bit mode upon startup.
Signed-off-by: Stefan Roese <sr@denx.de>
Some CPUs like PPC, BLACKFIN need sync() to ensure cfi flash write command
is fully finished. The sync() is defined in each CPU's io.h file. For
those CPUs which do not need sync for now, a dummy sync() is defined in
their io.h as well.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
This patch removes some problems when the Xilinx SystemACE driver
is used with 16bit access on an big endian platform (like the
AMCC Katmai).
Signed-off-by: Stefan Roese <sr@denx.de>
Block device read/write is anonymous data; there is no need to use a
typed pointer. void * is fine. Also add a hook for block_read functions
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Register read/write does not need to be wrapped in a full function. The
patch replaces them with macros.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The code in this file is not a command; it is a device driver. Put it in
the correct place. There are zero functional changes in this patch, it
only moves the file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Conflicts:
drivers/cfi_flash.c
The patch by Heiko Schocher <hs@pollux.denx.de> on Jan, 19, 2007
fixes cfi_driver bug for mpc7448hpc2 board. The default cfi_driver can support
mpc7448hpc2 board.
Here the description from Brian Brelsford <Brian_Brelsford@dell.com>:
The Hynix part returns a 0x1d in the 4th ID byte. The Samsung part
returns a 0x15. In the code fragment below bits [1:0] determine the
page size, it is ANDed via "(extid & 0x3)" then shifted out. The
next field is also ANDed with 0x3. However this is a one bit field
as defined in the Hynix and Samsung parts in the 4th ID byte that
determins the oobsize, not a two bit field. It works on Samsung as
bits[3:2] are 01. However for the Hynix there is a 11 in these two
bits, so the oob size gets messed up.
I checked the correct linux code and the suggested fix from Brian is
also available in the linux nand mtd driver.
Signed-off-by: Stefan Roese <sr@denx.de>
The conflicts due to a new mpc7448 p3m7448 board is in the main tree.
Merge branch 'master' into hpc2
Conflicts:
MAKEALL
cpu/74xx_7xx/cpu.c
cpu/74xx_7xx/cpu_init.c
cpu/74xx_7xx/speed.c
(1) remove some C++ comments.
(2) remove trailing white space.
(3) remove trailing empty line.
(4) Indentation by table.
(5) remove {} in one line condition.
(6) add space before '(' in function call.
Remove some weird printf () output.
Add necessary comments.
Modified Makefile to support building in a separate directory.
Two fixes for the nand_wait() function in
drivers/nand/nand_base.c:
1. Use correct timeouts. The original timeouts in Linux
source are 400ms and 20ms not 40s and 20s
2. Return correct error value in case of timeout. 0 is
interpreted as OK.
Signed-off-by: Rui Sousa <rui.sousa@laposte.net>
Signed-off-by: Stefan Roese <sr@denx.de>
and adapted board configs TQM5200 and yosemite accordingly. This commit
also makes the maximum number of root hub ports configurable
(CFG_USB_OHCI_MAX_ROOT_PORTS).
* Adds support for AMD command set Top Boot flash geometry reversal
* Adds support for reading JEDEC Manufacturer ID and Device ID
* Adds support for displaying command set, manufacturer id and
device ids (flinfo)
* Makes flinfo output to be consistent when CFG_FLASH_EMPTY_INFO defined
* Removes outdated change history (refer to git log instead)
Signed-off-by: Tolunay Orkun <listmember@orkun.us>
Signed-off-by: Stefan Roese <sr@denx.de>
Update the 83xx tree to use I2C support in drivers/fsl_i2c.c. Delete
cpu/mpc83xx/i2c.c, include/asm-ppc/i2c.h, and all references to those files.
Added multiple I2C bus support to fsl_i2c.c.
Signed-off-by: Timur Tabi <timur@freescale.com>
Replace all instances of CFG_IMMRBAR with CFG_IMMR, so that the 83xx
tree matches the other 8xxx trees.
Signed-off-by: Timur Tabi <timur@freescale.com>
PREREQUISITE PATCHES:
* This patch can only be applied after the following patches have been applied:
1) DNX#2006090742000024 "Add support for multiple I2C buses"
2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x"
3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c"
4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems"
5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems"
CHANGELOG:
* Add support for the Freescale MPC8349E-mITX reference design platform.
The second TSEC (Vitesse 7385 switch) is not supported at this time.
Signed-off-by: Timur Tabi <timur@freescale.com>
This patch addresses a problem when CONFIG_MTD_NAND_VERIFY_WRITE is
defined
and the write crosses a block boundary. The pointer to the verification
buffer (bufstart) is not being updated to reflect the starting of the
new
block so the verification of the second block fails.
CHANGELOG:
* Fix NAND FLASH page verification across block boundaries
Added a phy initialization to adjust the RGMII RX and TX timing
Always set the R100 bit in 100 BaseT mode regardless of the TSEC mode
Signed-off-by: Nick Spence <nick.spence@freescale.com>
titled "CFI Driver Little-Endian write Issue".
http://sourceforge.net/mailarchive/message.php?msg_id=36311999
If that patch applied, please discard this one.
Until now , I do not see his patch is applied. So please apply this one.
Signed-off-by: Yuli Barcohen <yuli@arabellasw.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The i2c Interface provides a master-only, serial interface that can be
used for initializing Tsi108/Tsi109 registers from an EEPROM after a
device reset.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
If there is no pci card, the tsi108/109 pci configure read will
cause a machine check exception to the processor. PCI error should
also be cleared after the read.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The following is a brief description of the Ethernet controller:
The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent
Gigabit Ethernet ports,E0 and E1. It uses a single Management interface
to manage the two physical connection devices (PHYs). Each Ethernet port
has its own statistics monitor that tracks and reports key interface
statistics. Each port supports a 256-entry hash table for address
filtering. In addition, each port is bridged to the Switch Fabric
through a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO.
Each Ethernet port also has a pair of internal Ethernet DMA channels to
support the transmit and receive data flows. The Ethernet DMA channels
use descriptors set up in memory, the memory map of the device, and
access via the Switch Fabric. The Ethernet Controller?s DMA arbiter
handles arbitration for the Switch Fabric. The Controller also
has a register businterface for register accesses and status monitor
control.
The PMD (Physical Media Device) interface operates in MII, GMII, or TBI
modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs.
The GMII and TBI modes are used to connect with Gigabit PMDs. Internal
data flows to and from the Ethernet Controller through the Switch Fabric.
Each Ethernet port uses its transmit and receive DMA channels to manage
data flows through buffer descriptors that are predefined by the
system (the descriptors can exist anywhere in the system memory map).
These descriptors are data structures that point to buffers filled
with data ready to transmit over Ethernet, or they point to empty
buffers ready to receive data from Ethernet.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
1. Add 7447A and 7448 processor support.
2. Add the following flags.
CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically
(such as by switch on board), this flag should be set.
CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot
relocates to RAM, this flag should be set.
CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the
system hang in exception, this flag should be set.
There is a design issue for tsi108/109 pci configure read. When pci scan
the slots, if there is no pci card, the tsi108/9 will cause a machine
check exception for mpc7448 processor.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
chpart, nboot and NAND subsystem related commands now accept also partition
name to specify offset.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Patch by Haavard Skinnemoen, 06 Sep 2006
This is a first attempt at creating a common serial driver for Atmel
chips. For now, it supports the AT32AP7000 AVR32 chip, but it should
be possible to support AT91RM9200 and other ARM-based chips with some
minor modifications.
There's nothing fundamentally AVR32-specific in this driver, but it
does use some features which are currently only defined for the
AT32AP CPU port:
* pm_get_clock_freq: Obtain the clock frequency of a given domain
* gd->console_uart: A "struct device" containing information about
register mappings, gpio resources and clocks associated with the
UART device.
For more information about these features, please see the "AT32AP
CPU" patch.
Introduced COFIG_FSL_I2C to select the common FSL I2C driver.
And removed hard i2c path from a few u-boot.lds scipts too.
Minor whitespace cleanups along the way.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
conditional expressions instead.
Use consistent return code 0/-1 for good/bad indicators.
Include one fewer file if the driver isn't used at all.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
- JFFS2 related commands implemented in mtd-utils style
- Support for bad blocks
- Bad block testing commands
- NAND lock commands
Please take a look at doc/README.nand for more details
Patch by Guido Classen, 10 Oct 2006
* Added support for using eTSEC 3 and eTSEC 4 on the 8548 CDS.
This will only work on rev 1.3 boards (but doesn't break older boards)
* Cleaned up some comments to reflect the expanded role of tsec
in other systems
Modifications are based on the linux kernel approach and
support two use cases:
1) Add O= to the make command line
'make O=/tmp/build all'
2) Set environement variable BUILD_DIR to point to the desired location
'export BUILD_DIR=/tmp/build'
'make'
The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'
Command line 'O=' setting overrides BUILD_DIR environent variable.
When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
The PS/2 keyobard driver for the TQM85xx modules only supports the
internal DUART of the MPC85xx CPU. Since the MPC8560 doesn't
include a DUART, the TQM8560 modules can't be used with the PS/2
keyboard controller on the STK85xx board.
The PS/2 keyboard driver should work with the modules TQM8540,
TQM8541 and TQM8555, but it only has been tested on a TQM8540, yet.
Make sure the PS/2 controller on the STK85xx is programmed. Jumper
settings: X66 1-2, 9-10; X61 2-3
Patch by Martin Krause, 21 Jun 2006
The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module
integrated in a little aluminium case.
Patch by Martin Krause, 8 Jun 2006
Some code cleanup
Notes:
- Board-dependend code for RPXLITE and RPXCLASSIC-based boards
placed to the drivers/rpx_pmcia.c file to avoid duplication.
Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
- drivers/i82365.c has been split into two parts located at
board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
the only boards using CONFIG_82365).
- Changes were tested for clean build and *very* *few* boards.
When tftp a non-exist file from the tftp server, u-boot will check
the link of all eth port. The original file will return wrong link
state on the no link ports.
signed-off-by: Jason Jin <Jason.Jin@freescale.com>
During the pci scan process, Some devices return bar_reponse with the
highest bytes 0, such as the pci bridge in uli1575 return bar_response
with 0xffffff, So the bar_size should be manually set under 64K.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Patch by Martin Krause, 07 Nov 2005
Tested on a STK85XX baseboard. Make sure the PS/2 controller
has been programmed. Jumper Settings: X66 1-2, 9-10; X61 2-3
- Add support for mpc8xx USB device.
- Add support for Common Device Class - Abstract Control Model USB console.
- Add support for flow control in USB slave devices.
- Add support for switching between gserial and cdc_acm using environment.
- Minor changes to usbdcore_omap1510.c usbdcore_omap1510.h
- Update usbcore slightly to ease host enumeration.
- Fix non-portable endian problems in usbdcore and usbdcore_ep0.
- Add AdderUSB_config as a defconfig to enable usage of the USB console
by default with the Adder87x U-Boot port.
Patches by Bryan O'Donoghue <bodonoghue@codehermit.ie>, 29 May 2006
- Add Intel legacy lock/unlock support to common CFI driver
On some Intel flash's (e.g. Intel J3) legacy unlocking is
supported, meaning that unlocking of one sector will unlock
all sectors of this bank. Using this feature, unlocking
of all sectors upon startup (via env var "unlock=yes") will
get much faster.
- Fixed problem with multiple reads of envronment variable
"unlock" as pointed out by Reinhard Arlt & Anders Larsen.
- Removed unwanted linefeeds from "protect" command when
CFG_FLASH_PROTECTION is enabled.
- Changed p3p400 board to use CFG_FLASH_PROTECTION
Patch by Stefan Roese, 01 Apr 2006
* Changes/fixes for drivers/cfi_flash.c:
- Correctly handle the cases where CFG_HZ != 1000 (several
XScale-based boards)
- Fix the timeout calculation of buffered writes (off by a
factor of 1000)
Patch by Anders Larsen, 31 Mar 2006
- add support for Analog Devices Blackfin BF533 CPU
- add support for the ADI BF533 Stamp uClinux board
- add support for the ADI BF533 EZKit board
Patches by Richard Klingler, June 11th 2005:
* For READ_STATUS and READID commands always 8 bytes need to be read from
NDDB. Otherwise they stay there and get send to flash as the first data
word when writing.
* In nand_base.c the oob variable is not reset so this->oob_buf is
overwritten what eventually screws up the bad block descriptor table.
code and in SoC code). Boards using the old way have CFG_NAND_LEGACY and
BOARDLIBS = drivers/nand_legacy/libnand_legacy.a added. Build breakage for
NETTA.ERR and NETTA_ISDN - will go away when the new NAND support is
implemented for these boards.
* Add env-variable "unlock" to handle initial state of sectors
(locked/unlocked).
Only the U-Boot image and it's environment is protected,
all other sectors are unprotected (unlocked) if flash
hardware protection is used (CFG_FLASH_PROTECTION) and
the environment variable "unlock" is set to "yes".
Patch by Stefan Roese, 28 Feb 2006
* Update drivers/cfi_flash.c:
- find_sector() called in both versions of flash_write_cfiword()
Patch by Peter Pearse, 27th Feb 2006
* CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode
Patch by Jose Maria Lopez, 16 Jan 2006
* Add support for AMD/Spansion Flashes in flash_write_cfibuffer
Patch by Alex Bastos and Thomas Schaefer, 2005-08-29
* Changes/fixes for drivers/cfi_flash.c:
We *should* check if there are any error bits if the previous call
returned ERR_OK (Otherwise we will have output an error message in
flash_status_check() already.) The original code would only check for
error bits if flash_status_check() returns ERR_TIMEOUT.
Patch by Marcus Hall, 23 Aug 2005
* Changes/fixes for drivers/cfi_flash.c:
- Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c
- Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c
Patch by Sangmoon Kim, 19 Aug 2005
* Fixes for drivers/cfi_flash.c:
- Fix wrong timeout value usage in flash_status_check()
- Round write_tout up when converting to msec in flash_get_size()
- Remove clearing flash status at the end of flash_write_cfibuffer()
which sets Intel 28F640J3 flash back to command mode on CSB472
Patch by Tolunay Orkun, 02 July 2005
If a host controller sets up a region as prefetchable and
a device's BAR denotes it as prefetchable, allocate the
BAR into the prefetch region.
If a BAR is prefetchable and no prefetchable region has
been setup by the controller we fall back to allocating
the BAR into the normally memory region.
Patch by Kumar Gala 11 Jan 2006
- Added onboard PPC440 DDR autodetection in cpu/ppc/sdram.c
- CFG_FLASH_QUIET_TEST added to use the common CFI driver
for bank autodetection
Patch by Stefan Roese, 22 Nov 2005
- Resolve the FIXME with respect to saving the u-boot environment.
- Make the default load address land in real memory.
- Fix lan91c96 SMC_{in,out}{b,w,l}() macros
Patch by David Brownell, 10 Mar 2005
- fix for ES2 differences.
- switch to using the cfi_flash driver.
- fix SRAM build address.
- fix for GP device operation.
- unlock SRAM for GP devices.
- display more device information.
- fix potential deadlock in omap24xx_i2c driver.
- fix DLL load values to match dpllout*1 operation.
- fix 2nd chip select init for combo DDR device.
- add support for CFI Intel 28F256L18 on H4 board.
Patch by Richard Woodruff, 03 Mar 2005
Use drivers/cfi_flash.c instead of private flash driver;
Remove hardcoded personalized settings from omap5912osk.h;
Fix spacing with (RO) marks in 'flinfo' output.
Patch by Michael Bendzick, 14 Jan 2005
Fix "WARNING: flash_make_cmd: unsuppported LittleEndian mode"
message when probing for nonexistent flash in little endian mode.
As a side effect more efficient and smaller code is generated,
which is always a Good Thing (TM).
Patch by Ladislav Michl, 24 Sep 2005
Add support for gzip compressed bmp's (CONFIG_VIDEO_BMP_GZIP).
Add support for eeprom write-enable (CFG_EEPROM_WREN).
Patch by Stefan Roese, 22 Sep 2005
- use TQM5200_auto as MAKEALL target for TQM5200 systems
- add support for SM501 graphics controller
- add support for graphic console on TQM5200
- add support for TQM5200 Rev 200
- cleanup, fix typo in include/configs/TQM5200.h
* Patch by Richard Woodruff, 10 Jan 2005:
Update support for OMAP2420 (ARM11) and H4 board:
o clean up and add new types to H4 memory probe code.
o fix to work with internal boot.
o added PRCM config III operation.
o fix marginal flash timings.
o add revison ATAG usage.
o enable voltage scaling at power chip.
o fix compile error for i2c.
* Fix network problem (error when receiving multiple ARP packets)
add support for the TI OMAP2420 processor and its H4 reference
board
* Patch by Christian Pellegrin, 24 Sep 2004:
Added support for NE2000 compatible (DP8390, DP83902) NICs.
Reset monitor size back to 256 so environment can be written
to flash on MPC85xx ADS and CDS releases.
* Patch by Paolo Broggini, 02 Sep 2004:
Make BSS clearing on ARM systems more robust
* Patch by Yue Hu and Joe, 01 Sep 2004:
- add PCI support for ixp425;
- add EEPRO100 suppor tfor ixdp425 board.
* Fix problem with protected sector detection in driver/cfi_flash.c
* Cleanup confusing use of CONFIG_ETH*ADDR - ust his only to
pre-define a MAC address; use CONFIG_HAS_ETH* to enable support for
additional ethernet addresses.
* Cleanup drivers/i82365.c - avoid duplication of code
* Fix bogus "cannot span across banks" flash error message
* Add support for CompactFlash for the CPC45 Board.
- Add support to revA version of PQ27 and PQ27E.
- Reverted MPC8260ADS baudrate back to original 115200
* Patch by Hojin, 17 Sep 2004:
Fix typo in cfi_flash.c
* Patch by Mark Jonas, 09 September 2004:
mtest's data line test (with CFG_ALT_MEMTEST set) returned a wrong
error message
* Patch by Mark Jonas, 31 August 2004:
Added option CFG_XLB_PIPELINING to enable XLB pipelining. This
improves FTP performance for MPC5200 systems. Enabled for IceCube
by default.
* Patches by Michael Bendzick, 30 Aug 2004:
- Configure omap1510inn board to use drivers/cfi_flash.c
- Make drivers/cfi_flash.c protect environment and redundant
environment.
* Patch by Steven Scholz, 23 Jun 2004:
- Add script (tools/img2brec.sh) to programm U-Boot into
(Synch)Flash using the Bootstrap Mode of the MC9328MX1/L
- Fix a typo in README
- Align "(RO)" output for "flinfo" after "protect on"
- Add RESET support for RPXlite_DW board; adjust CPU:BUS frequency
ratio 1:1 when core frequency less than 50MHz
- Introducing the concept of SoCs "./cpu/$(CPU)/$(SOC)"
- creating subdirs for SoCs ./cpu/arm920t/imx and ./cpu/arm920t/s3c24x0
- moving SoC specific code out of cpu/arm920t/ into cpu/arm920t/$(SOC)/
- moving drivers/s3c24x0_i2c.c and drivers/serial_imx.c out of drivers/
into cpu/arm920t/$(SOC)/
Set the PCI class code for JSE board as part of PCI interface setup
* Patch by Michael Bendzick, 15 Jul 2004:
Fix problem with writes with odd sizes in drivers/cfi_flash.c when
CFG_FLASH_USE_BUFFER_WRITE is set
Update etags build target
* Improve NetConsole support: add support for broadcast destination
address and buffered input.
* Cleanup compiler warnings for GCC 3.3.x and later
* Fix problem in cmd_jffs2.c introduced by CFG_JFFS_SINGLE_PART patch
change timing for SM501 graphics controller on TQM5200 module
* Patch by Mark Jonas, 13 July 2004:
- Total5200 LCD now run in little endian mode. Endianess conversion
is done in hardware.
- Removed last reference to "console" environment variable.
Replaced hardcoded PL011 clock frequency with config variable.
Fixed wrong CONFIG_CMD_DFL doc.
* Patch by Thomas Viehweger, 09 Jun 2004:
make it possible to remove chpart when there is only one partition
* Patch by Sascha Hauer, 28 Jun:
- add generic support for Motorola i.MX architecture
- add support for mx1ads, mx1fs2 and scb9328 boards
* Patches by Marc Leeman, 23 Jul 2004:
- Add define for the PCI/Memory Buffer Configuration Register
- corrected comments in cpu/mpc824x/cpu_init.c
* Add support for multiple serial interfaces
(for example to allow modem dial-in / dial-out)
* Patch by Mark Jonas, 05 Jul 2004:
add support for the Total5100's and Total5200's LCD screen
* Patches by Dan Eisenhut, 01 Jul 2004:
- README fixes.
- Move doc2000.h include to prevent compiler warning on some boards
- add empty include/asm-microblaze/processor.h
- add to CREDITS and MAINTAINERS
- add gd initialization
- add MicroBlaze and SUZAKU board to MAKEALL script
- add reset support for SUZAKU
- add flush_cache() for MicroBlaze
- add CFG_FLASH_SIZE to include/configs/suzaku.h since we have fixed
size flash memory on SUZAKU
* Patch by Daniel Poirot, 24 Jun 2004:
Add support for Wind River's sbc8240 board
* Patches by Yasushi Shoji, 26 Jun 2004:
- drivers/serial_xuartlite.c: fix "return 0" in void function
- add microblaze support to mkimage tool
Remove obsolete AdderII port which was superseded by unified
AdderII/Adder87x port
* Patch by Ladislav Michl, 16 Jun 2004:
Fix gcc-3.3.3 warnings for smc91111.c
Add support for MAX6900 RTC
* Patches by Ladislav Michl, 03 Jun 2004:
- fix cfi_flash.c on LE systems
- let 'make mrproper' delete u-boot.img as well
- turn printf into debug in cfi_flash.c
- Add support for the Logic Zoom LH7A40x based SDK board(s),
specifically the LPD7A400.
* Patches by Robert Schwebel, 15 May 2004:
- call MAC address reading code also for SMSC91C111;
- make SMSC91C111 timeout configurable, remove duplicate code
- fix get_timer() for PXA
- update doc/README.JFFS2
- use "bootfile" env variable also for jffs2
Add support for OMAP730 Perseus2 Development board
* Patch by Alan J. Luse, 29 Apr 2004:
Fix flash chip-select (OR0) option register setting on FADS boards.
* Patch by Alan J. Luse, 29 Apr 2004:
Report MII network speed and duplex setting properly when
auto-negotiate is not enabled.
* Patch by Jarrett Redd, 29 Apr 2004:
Fix hang on reset on Ocotea board due to flash in wrong mode.
Using external watchdog for KUP4 boards in mpc8xx/cpu.c;
load_sernum_ethaddr() for KUP4 boards in lib_ppc/board.c;
various changes to KUP4 board specific files
* Fixes for SL811 USB controller:
- implement workaround for broken memory stick
- improve error handling
* Increase packet send timeout to 10 ms in cpu/mpc8xx/scc.c to better
cope with congested networks.
JFFS2 speed enhancements:
- repair header CRC calculation in jffs2_1pass.c
- add eraseblock size to the partition information to skip empty
eraseblocks if we find more then 4k of free space.
- The JFFS2 scanner is now fast enough to remove the spinning wheel
so #ifdef-ed out.
- add watchdog calls in long running loops
* Patch by Philippe Robin, 22 Apr 2004:
Fix ethernet configuration for "versatile" board
* Patch by Kshitij Gupta, 21 Apr 2004:
Remove busy loop and use MPU timer fr usleep() on OMAP1510/1610 boards
* Patch by Steven Scholz, 24 Feb 2004:
Fix a bug in AT91RM9200 ethernet driver:
The MII interface is now initialized before accessing the PHY.
* Cleanup PCI ID's
sticks (including FAT / VFAT filesystem support)
* Add SL811 Host Controller Interface driver for USB
* Add CFG_I2C_EEPROM_ADDR_OVERFLOW desription to README
* Patch by Pantelis Antoniou, 19 Apr 2004:
Allow to use shell style syntax (i. e. ${var} ) with standard parser.
Minor patches for Intracom boards.
* Patch by Christian Pell, 19 Apr 2004:
cleanup support for CF/IDE on PCMCIA for PXA25X
fix initdram function for utx8245 board
* Patch by Markus Pietrek, 14 Apr 2004:
use ATAG_INITRD2 instead of deprecated ATAG_INITRD tag
* Patch by Reinhard Meyer, 18 Apr 2004:
provide the IDE Reset Function for EMK 5200 boards
* Patch by Masami Komiya, 12 Apr 2004:
fix pci_hose_write_config_{byte,word}_via_dword problems
- add support for the Epson 156x series of graphical displays
(These displays are serial and not suitable for using a normal
framebuffer console on them)
- add infrastructure needed in order to POST any DSPs in a board
Add Reiserfs support
* Patch by Hinko Kocevar, 20 Mar 2004
- Add auto-release for SMSC LAN91c111 driver
- Add save/restore of PTR and PNR regs as suggested in datasheet
- Unify video mode handling for Chips & Technologies 69000 Video
chip and Silicon Motion SMI 712/710/810 Video chip
- Add selection of the video output (CRT or LCD) via 'videoout'
environment variable for the Silicon Motion
- README update
* Patch by Pierre Aubert, 18 Mar 2004:
include/common.h typo fix
* Patches by Tolunay Orkun, 17 Mar 2004:
- Add support for bd->bi_iic_fast[] initialization via environment
variable "i2cfast" (CONFIG_I2CFAST)
- Add "i2cfast" u-boot environment variable support for csb272
- show PCI clock frequency on MPC8260 systems
- add FCC_PSMR_RMII flag for HiP7 processors
- in do_jffs2_fsload(), take load address from load_addr if not set
explicit, update load_addr otherwise
- replaced printf by putc/puts when no formatting is needed
(smaller code size, faster execution)
attempting to switch on USB on SX1 board.
* Patch by Josef Wagner, 18 Mar 2004:
- Add support for MicroSys XM250 board (PXA255)
- Add support for MicroSys PM828 board (MPC8280)
- Add support for 32 MB Flash on PM825/826
- new SDRAM refresh rate for PM825/PM826
- added support for MicroSys PM520 (MPC5200)
- replaced Query by Identify command in CPU86/flash.c
to support 28F160F3B
* Fix wrap around problem with udelay() on ARM920T
* Add support for Macronix flash on TRAB board
- Fix Gigabit Ethernet support for 440GX
- Add Gigabit Ethernet Support to MII PHY utilities
* Patch by Brad Kemp, 12 Mar 2004:
Fixes for drivers/cfi_flash.c:
- Better support for x8/x16 implementations
- Added failure for AMD chips attempting to use CFG_FLASH_USE_BUFFER_WRITE
- Added defines for AMD command and address constants
* Patch by Leon Kukovec, 12 Mar 2004:
Fix get_dentfromdir() to correctly handle deleted dentries
* Patch by George G. Davis, 11 Mar 2004:
Remove hard coded network settings in TI OMAP1610 H2
default board config
* Patch by George G. Davis, 11 Mar 2004:
add support for ADS GraphicsClient+ board.
- add bitmap command and splash screen support in cfb console
- add [optional] origin in the bitmap display command
* Patch by Travis Sawyer, 11 Mar 2004:
Fix ocotea board early init interrupt setup.
* Patch by Thomas Viehweger, 11 Mar 2004:
Remove redundand code; add PCI-specific bits to include/mpc8260.h
- Add support for the SSV ADNP/ESC1 (Nios Softcore)
* Patch by George G. Davis, 9 Mar 2004:
fix recent build failure for SA1100 target
* Patch by Travis Sawyer, 09 Mar 2004:
Support native interrupt mode for the IBM440GX.
Previously it was running in 440GP compatibility mode.
Added ARM Integrator AP, CP and Versatile PB926EJ-S Reference
Platform support.
* Patch by Masami Komiya, 08 Mar 2004:
Don't overwrite server IP address or boot file name
when the boot server does not return values
* Patch by listmember@orkun.us, 5 Mar 2004:
Removed compile time restriction on CFG_I2C_SPEED for DS1338 RTC
Fix early board initialization for Cogent CSB272 board
* Patch by Ed Okerson, 3 Mar 2004:
fix CFI flash writes for little endian systems
* Patch by Reinhard Meyer, 01 Mar 2004:
generalize USB and IDE support for MPC5200 with according
changes to IceCube.h and TOP5200.h
add Am29LV256 256 MBit FLASH support for TOP5200 boards
add info about USB and IDE to README
NS9750 DevBoard added
* Patch by Pierre AUBERT, 24 Feb 2004
add USB support for MPC5200
* Patch by Steven Scholz, 24 Feb 2004:
- fix MII commands to use values from last command
* Patch by Torsten Demke, 24 Feb 2004:
Add support for the eXalion platform (SPSW-8240, F-30, F-300)
Fixes for for OMAP1610 board:
- shift some IRQ specific code to platform.S file
- remove duplicatewatchdog reset code from start.S
* Make Auto-MDIX Support configurable on INCA-IP board
* Fix license for mkimage tool
Add support for the Xilinx ML300 platform
* Patch by Stephan Linz, 17 Feb 2004:
Fix watchdog support for NIOS
* Patch by Josh Fryman, 16 Feb 2004:
Fix byte-swapping for cfi_flash.c for different bus widths
* Patch by Jon Diekema, 14 Jeb 2004:
Remove duplicate "FPGA Support" notes from the README file
Add support for NET+50 CPU and ModNET50 board
* Patch by Sam Song, 10 Feb 2004:
Fix typos in cfi_flash.c
* Patch by Leon Kukovec, 10 Feb 2004
Fixed long dir entry slot id calculation in get_vfatname
* Patch by Robin Gilks, 10 Feb 2004:
add "itest" command (operators: -eq, -ne, -lt, -gt, -le, -ge, ==,
!=, <>, <, >, <=, >=)
o 440GX:
- Fix PCI Indirect access for type 1 config cycles with ppc440.
- Add phymode for 440 enet
- fix pci pre init
o XPedite1K:
- Change board_pre_init to board_early_init_f
- Add user flash to bus controller setup
- Fix pci pre init
- Fix is_pci_host to check GPIO for monarch bit
- Force xpedite1k to pci conventional mode (via #define option)
* Patch by Brad Kemp, 4 Feb 2004:
- handle the machine check that is generated during the PCI scans
on 82xx processors.
- define the registers used in the IMMR by the PCI subsystem.
* Patch by Pierre Aubert, 03 Feb 2004:
cpu/mpc5xxx/start.S: copy MBAR into SPR311
* Patch by Jeff Angielski, 03 Feb 2004:
Fix copy & paste error in cpu/mpc8260/pci.c
* Patch by Reinhard Meyer, 24 Jan 2004:
Fix typo in cpu/mpc5xxx/pci_mpc5200.c
Allow bzip2 compression for small memory footprint boards
* Patch by Brad Kemp, 21 Jan 2004:
Add support for CFI flash driver for both the Intel and the AMD
command sets.
* Patch by Travis Sawyer, 20 Jan 2004:
Fix pci bridge auto enumeration of sibling p2p bridges.
* Patch by Tolunay Orkun, 12 Jan 2004:
Add some delays as needed for Intel LXT971A PHY support
* Patches by Stephan Linz, 09 Jan 2004:
- avoid warning: unused variable `piop' in board/altera/common/sevenseg.c
- make DK1C20 board configuration related to ASMI conform to
documentation
before we can access it; add delay in case we are faster (with no
CF card inserted)
* Cleanup of some init functions
* Make sure SCC Ethernet is always stopped by the time we boot Linux
to avoid Linux crashes by early packets coming in.
* Accelerate flash accesses on LWMON board by using buffered writes
