This patch mainly adds ACPI support to QEMU.
Verified by booting Linux kernel on QEMU Q35.
Signed-off-by: Saket Sinha <saket.sinha89@gmail.com>
Minor whitespace fixes and dropped mention of i440FX in commit message:
Signed-off-by: Simon Glass <sjg@chromium.org>
It turns out that calling fsp_init_phase_pci() in arch_misc_init()
is subject to break pci device drivers as with driver model, when
the bus enumeration happens is not deterministic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
With dm pci conversion, pci config read/write in unprotect_spi_flash()
silently fails as at that time dm pci is not ready and bus enumeration
is not done yet. Actually we don't need to do this in that early phase,
hence we delay this call to arch_misc_init().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add some comments in start.S for the fact that with FSP U-Boot
actually enters the code twice. Also change to use fsp_init()
and fsp_continue for accuracy.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
After fsp_init() returns, the stack has already been switched to a
place within system memory as defined by CONFIG_FSP_TEMP_RAM_ADDR.
Enlarge the size of malloc() pool before relocation since we have
plenty of memory now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some platforms may have >=4GiB memory, so we need make U-Boot report
such configuration correctly when booting as the coreboot payload.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have generic routine to calculate relocation address,
remove the x86 specific one which is now only used by coreboot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
coreboot has some extensions (type 6 & 16) to the E820 types.
When we detect this, mark it as E820_RESERVED.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This can fail for internal reasons, so return a sensible value rather than
a random one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Multiple APs are brought up simultaneously and they may get the same
seq num in the uclass_resolve_seq() during device_probe(). To avoid
this, set req_seq to the reg number in the device tree in advance.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
When trying to figure out where an exception has occured, the relocated
address is not a lot of help. Its value depends on various factors. Show
the un-relocated IP as well. This can be looked up in System.map directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is quite a bit of assembler code that can be removed if we use the
generic global_data setup. Less arch-specific code makes it easier to add
new features and maintain the start-up code.
Drop the unneeded code and adjust the hooks in board_f.c to cope.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rather than keeping track of the Global Descriptor Table in its own memory
we may as well put it in global_data with everything else. As a first step,
stop using the separately allocated GDT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We should not fiddle with interrupts or the FSP when running as an EFI
payload. Detect this and skip this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We should signal to the FSP that PCI enumeration is complete. Perform this
task in a suitable place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function can fail. In this case we should return the error rather than
swallowing it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This code could use a little tightening up. There is some repetition and
an odd use of fdtdec_get_int_array().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Allow for configuration of FSP UPD from the device tree which will
override any settings which the FSP was built with itself.
Modify the MinnowMax and BayleyBay boards to transfer sensible UPD
settings from the Intel FSPv4 Gold release to the respective dts files,
with the condition that the memory-down parameters for MinnowMax are
also used.
Signed-off-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Removed fsp,mrc-debug-msg and fsp,enable-xhci for minnowmax, bayleybay
Fixed lines >80col
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable the debug UART and emit a single 'a' early in the init sequence to
show that it is working.
Unfortunately the debug UART implementation needs a stack to work. I cannot
seem to remove this limitation as the absolute 'jmp %eax' instruction goes
off into the weeds.
So this means that the character output cannot be any earlier than
car_init_ret, where memory is available for a stack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Disable a few things which interfere with the EFI init. This allows QEMU to
to boot into EFI, load a U-Boot payload then boot to the U-Boot prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Disable a few things which interfere with the EFI init. This allows the
Minnowboard MAX to boot into EFI, load a U-Boot payload then boot to the
U-Boot prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot runs as an EFI payload it needs to avoid setting up the CPU
again. Also U-Boot currently does not handle interrupts for many devices, so
run with interrupts disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The EFI stub provides information to U-Boot in a table. This includes the
memory map which is needed to decide where to relocate U-Boot. Collect this
information in the early init code and store it in global_data.
Fix up the BIST code at the same time since we don't have it when booting
from EFI and can assume it is 0.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The procedure to drop from 64-bit mode to 32-bit is a bit messy. Add a
function to take care of it. It requires identity-mapped pages and that
the calling code is running below 4GB.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a linker script and relocation code for building 64-bit EFI
applications. This can be used for the EFI stub.
Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add the required x86 glue code. This includes the initial start-up,
relocation and jumping to efi_main(). We also need to avoid fiddling with
interrupts.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix a typo, remove an unused field and make sure to use existing #define
constants instead of open-coded values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The GDT works but technically the length is incorrect. Fix this and add a
comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These flags now overlap some global ones. Adjust the x86-specific flags to
avoid this. Since this requires a change to the start.S code, add a way for
tools to find the 32-bit cold reset entry point. Previously this was at a
fixed offset.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix a typo, improve some comments and add a little more detail in some
cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add PCI IRQ routing information in the board device tree and enable
writing PIRQ routing table and MP table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently cpu-x86 driver is probed only for SMP. We add the same
support for UP when there is only one cpu node in the deive tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The PIIX3 chipset does not integrate an I/O APIC, instead it supports
connecting to an external I/O APIC which needs to be enabled manually.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We need walk through all functions within a PCI device and assign
their IRQs accordingly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a RTC node in the device tree to enable DM RTC support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
(Squashed in 'x86: Fix RTC build error on ivybridge')
Turn on cache on the pci option rom area to improve the performance.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Instead of using switch..case for architecture defined exceptions,
simply unify the handling by printing a message of exception name,
followed by registers dump then halt the CPU.
With this unification, it also fixes the wrong exception numbers
for #MF/#AC/#MC/#XM which should be 16/17/18/19 not 15/16/17/18.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some exceptions cause an error code to be saved on the current stack
after the EIP value. We should extract CS/EIP/EFLAGS from different
position on the stack based on the exception number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Because the top-level Makefile forces all the source files
to include include/linux/kconfig.h (see the UBOOTINCLUDE define),
these includes are redundant.
By the way, there are exceptions for the statement above; host
programs. In fact, host tools in U-Boot depend on a particular
board configuration, although I think they should not. So, some
files still include <linux/config.h> to work around build errors
on host tools.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Commit afbbd413a fixed this for non-driver-model. Make sure that the driver
model code handles this also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust minnowmax to use driver model for PCI. This requires adding a device
tree node to specify the ranges, removing the board-specific PCI code and
ensuring that the host bridge is configured.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver should use the x86 PCI configuration functions. Also adjust its
compatible string to something generic (i.e. without a vendor name).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Per CPUID:80000008h result, the maximum physical address bits of
TunnelCreek processor is 32 instead of default 36. This will fix
the incorrect decoding of MTRR range mask.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should setup fixed range MTRRs for some legacy regions like VGA
RAM and PCI ROM areas as uncacheable. Note FSP may setup these to
other cache settings, but we can override this in x86_cpu_init_f().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
So far interrupt routing works pretty well for any on-chip devices
on Intel Crown Bay. When inserting any PCIe card to any PCIe slot,
Linux kernel is smart enough to do interrupt swizzling and figure
out device's irq using its parent bridge's interrupt routing info
all the way up to its root port. In U-Boot all PCIe root ports'
interrupts were routed to PIRQ E/F/G/H before, while actually all
PCIe downstream ports received INTx are routed to PIRQ A/B/C/D
directly and not configurable. Now we change this mapping so that
any external PCIe device can work correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Remove inline for lapic access routines and expose lapic_read()
& lapic_write() as APIs to read/write lapic registers. Also move
stop_this_cpu() to mp_init.c as it has nothing to do with lapic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
I/O APIC registers are addressed indirectly. Add io_apic_read() and
io_apic_write() routines to help register access. Two macros for I/O
APIC ID and version register offset are also added.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no need to populate multiple irq info entries with the same
bus number and device number, but with different interrupt pin. We
can use the same entry to store all the 4 interrupt pin (INT A/B/C/D)
routing information to reduce the whole PIRQ routing table size.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In fill_irq_info() pci device's function number is written into
the table, however this is not really necessary. The function
number can be anything as OS doesn't care about this field,
neither does the PIRQ routing specification. Change to always
writing 0 as the function number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should write correct bus number to the PIRQ routing table for the
irq router from device tree, instead of hard-coded zero.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit cleans up the lapic codes:
- Delete arch/x86/include/asm/lapic_def.h, and move register and bit
defines into arch/x86/include/asm/lapic.h
- Use MSR defines from msr-index.h in enable_lapic() and disable_lapic()
- Remove unnecessary stuff like NEED_LAPIC, X86_GOOD_APIC and
CONFIG_AP_IN_SIPI_WAIT
- Move struct x86_cpu_priv defines to asm/arch-ivybridge/bd82x6x.h, as
it is not apic related and only used by ivybridge
- Fix coding convention issues
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently lapic_setup() is called before calling mp_init(), which
then calls init_bsp() where it calls enable_lapic(), which was
already enabled in lapic_setup(). Hence move lapic_setup() call
into init_bsp() to avoid the duplication.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Most of the MP initialization codes in arch/x86/cpu/baytrail/cpu.c is
common to all x86 processors, except detect_num_cpus() which varies
from cpu to cpu. Move these to arch/x86/cpu/cpu.c and implement the
new 'get_count' method for baytrail and cpu_x86 drivers. Now we call
cpu_get_count() in mp_init() to get the number of CPUs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit does the following to clean up x86 cpu dm drivers:
- Move cpu_x86 driver codes from arch/x86/cpu/cpu.c to a dedicated
file arch/x86/cpu/cpu_x86.c
- Rename x86_cpu_get_desc() to cpu_x86_get_desc() to keep consistent
naming with other dm drivers
- Add a new cpu_x86_bind() in the cpu_x86 driver which does exactly
the same as the one in the intel baytrail cpu driver
- Update intel baytrail cpu driver to use cpu_x86_get_desc() and
cpu_x86_bind()
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The call to FspInitEntry is done in arch/x86/lib/fsp/fsp_car.S so far.
It worked pretty well but looks not that good. Apart from doing too
much work than just enabling CAR, it cannot read the configuration
data from device tree at that time. Now we want to move it a little
bit later as part of init_sequence_f[] being called by board_init_f().
This way it looks and works better in the U-Boot initialization path.
Due to FSP's design, after calling FspInitEntry it will not return to
its caller, instead it jumps to a continuation function which is given
by bootloader with a new stack in system memory. The original stack in
the CAR is gone, but its content is perserved by FSP and described by
a bootloader temporary memory HOB. Technically we can recover anything
we had before in the previous stack, but that is way too complicated.
To make life much easier, in the FSP continuation routine we just
simply call fsp_init_done() and jump back to car_init_ret() to redo
the whole board_init_f() initialization, but this time with a non-zero
HOB list pointer saved in U-Boot's global data so that we can bypass
the FspInitEntry for the second time.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
Currently the FSP execution environment GDT is setup by U-Boot in
arch/x86/cpu/start16.S, which works pretty well. But if we try to
move the FspInitEntry call a little bit later to better fit into
U-Boot's initialization sequence, FSP will fail to bring up the AP
due to #GP fault as AP's GDT is duplicated from BSP whose GDT is
now moved into CAR, and unfortunately FSP calls AP initialization
after it disables the CAR. So basically the BSP's GDT still refers
to the one in the CAR, whose content is no longer available, so
when AP starts up and loads its segment register, it blows up.
To resolve this, we load GDT before calling into FspInitEntry.
The GDT is the same one used in arch/x86/cpu/start16.S, which is
in the ROM and exists forever.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add RESET_SEG_START, RESET_SEG_SIZE and RESET_VEC_LOC Kconfig options
and make arch/x86/cpu/config.mk use these options.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
Baytrail physically maps the first 2 GB of SDRAM from 0x0 to 0x7FFFFFFF
and additional SDRAM is mapped from 0x100000000 and up. There is a
physical memory hole from 0x80000000 to 0xFFFFFFFF for other uses.
Because of this, PCI region 3 should only try to use up to the amount of
SDRAM or 0x80000000, which ever is less.
Signed-off-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Support QEMU PIRQ routing via device tree on both i440fx and q35
platforms. With this commit, Linux booting on QEMU from U-Boot
has working ATA/SATA, USB and ethernet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Writing 0xcb to I/O port 0xb2 (Advanced Power Management Control) causes
U-Boot to hang on QEMU q35 target. We introduce a config option in the
device tree "u-boot,no-apm-finalize" under /config node if we don't want
to do that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
As VGA option rom needs to run at C segment, although QEMU PAM emulation
seems to only guard E/F segments, for correctness, move VGA initialization
after PAM decode C/D/E/F segments.
Also since we already tested QEMU targets to differentiate I440FX and Q35
platforms, change to locate the VGA device via hardcoded b.d.f instead of
dynamic search for its vendor id & device id pair.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
QEMU always decode legacy IDE I/O ports on PIIX chipset. However Linux ata_piix
driver does sanity check to see whether legacy ports decode is turned on.
To make Linux ata_piix driver happy, turn on the decode via IDE_TIMING register.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
By default the legacy segments C/D/E/F do not decode to system RAM.
Turn on the decode via Programmable Attribute Map (PAM) registers
so that we can write configuration tables in the F segment.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
If pirq_routing_table points to NULL, that means U-Boot fails to
generate the table before in create_pirq_routing_table(), so we
test it against NULL before actually writing it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Quark SoC has the same interrupt routing mechanism as the
Queensbay platform, only the difference is that PCI devices'
INTA/B/C/D are harcoded and cannot be changed freely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
PIRQ routing is pretty much common in Intel chipset. It has several
PIRQ links (normally 8) and corresponding registers (either in PCI
configuration space or memory-mapped IBASE) to configure the legacy
8259 IRQ vector mapping. Refactor current Queensbay PIRQ routing
support using device tree and move it to a common place, so that we
can easily add PIRQ routing support on a new platform.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
It turns out that QEMU x86 emulated graphic card has a built-in
option ROM which can be run perfectly with native mode by U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces the initial U-Boot support for QEMU x86 targets.
U-Boot can boot from coreboot as a payload, or directly without coreboot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Merged in patch 'x86: qemu: Add CMD_NET to qemu-x86_defconfig
https://patchwork.ozlabs.org/patch/479745/
This driver supports multi-core init and sets up the CPU frequencies
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This permits init of additional CPU cores after relocation and when driver
model is ready.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Most modern x86 CPUs include more than one CPU core. The OS normally requires
that these 'Application Processors' (APs) be brought up by the boot loader.
Add the required support to U-Boot to init additional APs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function to return the address of the Interrupt Descriptor Table.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When we start up additional CPUs we want them to use the same Global
Descriptor Table. Store the address of this in global_data so we can
reference it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is annoying during development and serves no useful purpose since
warnings are clearly displayed now that we are using Kbuild. Remove this
option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that reset_cpu() functions correctly, use it instead of directly
accessing the port.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Now that reset_cpu() functions correctly, use it instead of directly
accessing the port.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The existing code is pretty ancient and is unreliable on modern hardware.
Generally it will hang.
We can use port 0xcf9 to initiate reset on more modern hardware (say in the
last 10 years). Update the reset_cpu() function to do this, and add a new
'full reset' function to perform a full power cycle.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot on coreboot does not have a driver for the PCH so cannot see the
SPI peripheral now that it has moved inside the PCH. Add a simple driver so
that SPI flash works again.
Signed-off-by: Simon Glass <sjg@chromium.org>
By default the legacy segments (A0000h-B0000h, E0000h-F0000h)
do not decode to system RAM. Turn on the decode so that we can
write configuration tables in the F segment.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement Intel Queensbay platform-specific PIRQ routing support.
The chipset PIRQ routing setup is called in the arch_misc_init().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We can write the configuration table in last_stage_init() for all x86
boards, but not with coreboot since coreboot already has them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a function to assign an IRQ number to PCI device's interrupt
line register in its configuration space, so that the PCI device
can have its interrupt working under PIC mode after OS boots up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The prefix PCH was taken from ivybridge port. However Queensbay
platform official document does not mention PCH. It is composed
of TunnelCreek processor and Topcliff IOH chipset. For accuracy,
avoid using PCH prefix in the macro.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The PCH (Platform Controller Hub) is on the PCI bus, so show it as such.
The LPC (Low Pin Count) and SPI bus are inside the PCH, so put these in the
right place also.
Rename the compatible strings to be more descriptive since this board is the
only user. Once we are using driver model fully on x86, these will be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple uclass for this chip which is often found in x86 systems
where the CPU is a separate device.
The device can have children, so make it scan the device tree for these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert this driver over to use driver model. Since all x86 platforms use
it, move x86 to use driver model for SPI and SPI flash. Adjust all dependent
code and remove the old x86 spi_init() function.
Note that this does not make full use of the new PCI uclass as yet. We still
scan the bus looking for the device. It should move to finding its details
in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move chromebook_link over to driver model for PCI.
This involves:
- adding a uclass for platform controller hub
- removing most of the existing PCI driver
- adjusting how CPU init works to use driver model instead
- rename the lpc compatible string (it will be removed later)
This does not really take advantage of driver model fully, but it does work.
Furture work will improve the code structure to remove many of the explicit
calls to init the board.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we do more in this function than we should. Split out the
post-driver-model part into a separate function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These functions currently use a generic name, but they are for x86 only.
This may introduce confusion and prevents U-Boot from using these names
more widely.
In fact it should be possible to remove these at some point and use
generic functions, but for now, rename them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some systems have more than 4GB of RAM. U-Boot can only place things below
4GB so any memory above that should not be used. Ignore any such memory so
that the memory size will not exceed the maximum.
This prevents gd->ram_size exceeding 4GB which causes problems for PCI
devices which use DMA.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Intel Quark SoC integrates two 10/100 ethernet controllers which can
be connected to an external RMII PHY. The MAC IP is from Designware.
Enable this support with the existing U-Boot Designware MAC driver
so that the ethernet port on Intel Galileo board can be used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Using __DATE__ and __TIME__ results in an error due to -Werror=date-time
with gcc-4.9 (__DATE__ / __TIME__ might prevent reproducible builds) so
switch these over to U_BOOT_DATE / U_BOOT_TIME
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch cleans up the quark MRC codes coding style by:
- Remove BIT0/1../31 defines from mrc_util.h
- Create names for the documented BITs and use them
- For undocumented single BITs, use (1 << n) directly
- For undocumented ORed BITs, use the hex number directly
- Remove redundancy parenthesis all over the codes
- Replace to use lower case hex numbers
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
Intel Galileo board has a microSD slot which is routed from Quark SoC
SDIO controller. Enable SD/MMC support so that we can use an SD card.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Quark SoC contains a legacy SPI controller in the legacy bridge
which is ICH7 compatible. Like Tunnel Creek and BayTrail, the BIOS
control register offset in the ICH SPI driver is wrong for the Quark
SoC too, unprotect_spi_flash() is added to enable the flash write.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC has some non-standard BARs (excluding PCI standard BARs)
which need be initialized with suggested values. This includes GPIO,
WDT, RCBA, PCIe ECAM and some ACPI register block base addresses.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we have added Quark MRC codes, call MRC in dram_init() so
that DRAM can be initialized on a Quark based board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
For some unknown reason, the TSC calibration via PIT does not work on
Quark. Enable bypassing TSC calibration and override TSC_FREQ_IN_MHZ
to 400 per Quark datasheet in the Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make the Intel quark/galileo support avaiable in Kconfig and Makefile.
With this patch, we can generate u-boot.rom for Intel galileo board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add minimum codes to support Intel Quark SoC. DRAM initialization
is not ready yet so a hardcoded gd->ram_size is assigned.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC contains an embedded 512KiB SRAM (eSRAM) that is
initialized by hardware. eSRAM is the ideal place to be used
for Cache-As-RAM (CAR) before system memory is available.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In the Quark SoC, some chipset commands are accomplished by utilizing
the internal message network within the host bridge (D0:F0). Accesses
to this network are accomplished by populating the message control
register (MCR), Message Control Register eXtension (MCRX) and the
message data register (MDR).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is a relatively low-cost x86 board in a small form factor. The main
peripherals are uSD, USB, HDMI, Ethernet and SATA. It uses an Atom 3800
series CPU. So far only the dual core 2GB variant is supported.
This uses the existing FSP support. Binary blobs are required to make this
board work. The microcode update is included as a patch (all 3000 lines of
it).
Change-Id: I0088c47fe87cf08ae635b343d32c332269062156
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
While queensbay is the first chip with these settings, others will want to
use them too. Make them common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since these board functions seem to be the same for all boards which use
FSP, move them into a common file. We can adjust this later if future FSPs
need more flexibility.
This creates a generic PCI MMC device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
For now this code seems to be the same for all FSP platforms. Make it
common until we see what differences are required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
If the BIOS emulator is not available, allow use of native execution if
available, and vice versa. This can be controlled by the caller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This setting will be used by more than just ivybridge so make it common.
Also rename it to PCIE_ECAM_BASE which is a more descriptive name.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The memory reference code takes a very long time to 'train' its SDRAM
interface, around half a second. To avoid this delay on every boot we can
store the parameters from the last training sessions to speed up the next.
Add an implementation of this, storing the training data in CMOS RAM and
SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing IP checksum function is only accessible to the 'coreboot' cpu.
Drop it in favour of the new code in the network subsystem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Various minor code format issues are fixed in start16.S:
- U-boot -> U-Boot
- 32bit -> 32-bit
- Use TAB instead of SPACE to indent
- Move the indention location of the GDT comment block
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On some x86 processors (like Intel Quark) the MTRR registers are not
supported. This is reflected by the CPUID (EAX 01H) result EDX[12].
Accessing the MTRR registers on such processors will cause #GP so we
must test the support flag before accessing MTRR MSRs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
CPUID (EAX 01H) returns MTRR support flag in EDX bit 12. Probe this
flag in x86_cpu_init_f() and save it in global data.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
arch/x86/cpu/mtrr.c has access to the U-Boot global data thus
DECLARE_GLOBAL_DATA_PTR is needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Configure coreboot pci memory regions so that pci device drivers
could work correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are many places in the U-Boot source tree which refer to
CONFIG_SYS_COREBOOT, CONFIG_CBMEM_CONSOLE and CONFIG_VIDEO_COREBOOT
that is currently defined in coreboot.h.
Move them to arch/x86/cpu/coreboot/Kconfig so that we can switch
to board configuration file to build U-Boot later.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
If coreboot is built with CONFIG_COLLECT_TIMESTAMPS, use the value
of base_time in coreboot's timestamp table as our timer base,
otherwise TSC counter value will be used.
Sometimes even coreboot is built with CONFIG_COLLECT_TIMESTAMPS,
the value of base_time in the timestamp table is still zero, so
we must exclude this case too (this is currently seen on booting
coreboot in qemu).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
These two are not worth having separate inline functions as they are
really simple, so drop them.
Also changed 'type' parameter of fsp_get_next_hob() from u16 to uint.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
At present the normal update (which happens much later) does not work. This
seems to have something to do with the 'no eviction' mode in the CAR, or at
least moving the microcode update after that causes it not to work.
For now, do an update early on so that it definitely works. Also refuse to
continue unless the microcode update check (later in boot) is successful.
Signed-off-by: Simon Glass <sjg@chromium.org>
For platforms with CAR we should disable it before relocation. Check if
this function is available and call it if so.
Signed-off-by: Simon Glass <sjg@chromium.org>
Cache-as-RAM should be turned off when we relocate since we want to run from
RAM. Add a function to perform this task.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should use MTRRs to speed up execution. Add a list of MTRR requests which
will dealt with when we relocate and run from RAM.
We set RAM as cacheable (with write-back) and registers as non-cacheable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Set the frame buffer to write-combining. This makes it faster, although for
scrolling write-through is even faster for U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Memory Type Range Registers are used to tell the CPU whether memory is
cacheable and if so the cache write mode to use.
Clean up the existing header file to follow style, and remove the unneeded
code.
These can speed up booting so should be supported. Add these to global_data
so they can be requested while booting. We will apply the changes during
relocation (in a later commit).
Signed-off-by: Simon Glass <sjg@chromium.org>
This is set up along with CAR (Cache-as-RAM) anyway. When we relocate we
don't really need ROM caching (we read the VGA BIOS from ROM but that is
about it)
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This takes about about 700ms on link when running natively and 900ms when
running using the emulator. It is a waste of time if video is not enabled,
so don't bother running the video BIOS in that case.
We could add a command to run the video BIOS later when needed, but this is
not considered at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Remove the troublesome union hob_pointers so that some annoying casts
are no longer needed in those hob access routines. This also improves
the readability.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Introduce a gd->hose to save the pci hose in the early phase so that
apis in drivers/pci/pci.c can be used before relocation. Architecture
codes need assign a valid gd->hose in the early phase.
Some variables are declared as static so change them to be either
stack variable or global data member so that they can be used before
relocation, except the 'indent' used by CONFIG_PCI_SCAN_SHOW which
just affects some print format.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On x86, some peripherals on pci buses need to be accessed in the
early phase (eg: pci uart) with a valid pci memory/io address,
thus scan the pci bus and do the corresponding resource allocation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
arch/x86/cpu/pci.c has access to the U-Boot global data thus
DECLARE_GLOBAL_DATA_PTR is needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is the follow-on patch to clean up the FSP support codes:
- Remove the _t suffix on the structures defines
- Use __packed for structure defines
- Use U-Boot's assert()
- Use standard bool true/false
- Remove read_unaligned64()
- Use memcmp() in the compare_guid()
- Remove the cast in the memset() call
- Replace some magic numbers with macros
- Use panic() when no valid FSP image header is found
- Change some FSP utility routines to use an fsp_ prefix
- Add comment blocks for asm_continuation and fsp_init_done
- Remove some casts in find_fsp_header()
- Change HOB access macros to static inline routines
- Add comments to mention find_fsp_header() may be called in a
stackless environment
- Add comments to mention init(¶ms) in fsp_init() cannot
be removed
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are two standard SD card slots on the Crown Bay board, which
are connected to the Topcliff PCH SDIO controllers. Enable the SDHC
support so that we can use them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Crown Bay board has an SST25VF016B flash connected to the Tunnel
Creek processor SPI controller used as the BIOS media where U-Boot
is stored. Enable this flash support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
To avoid having two microcode formats, adjust the build system to support
obtaining the microcode from the device tree, even in the case where it
must be made available before the device tree can be accessed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Implement minimum required functions for the basic support to
queensbay platform and crownbay board.
Currently the implementation is to call fsp_init() in the car_init().
We may move that call to cpu_init_f() in the future.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are several problems in the code. The device tree decode is incorrect
in ways that are masked due to a matching bug. Both are fixed. Also
microcode_read_rev() should be inline and called before the microcode is
written.
Note: microcode writing does not work correctly on ivybridge for me. Further
work is needed to resolve this. But this patch tidies up the existing code
so that will be easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are new microcode revisions available. Update them. Also change
the format so that the first 48 bytes are not omitted from the device tree
data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Per Intel FSP architecture specification, FSP provides 3 routines
for bootloader to call. The first one is the TempRamInit (aka
Cache-As-Ram initialization) and the second one is the FspInit
which does the memory bring up (like MRC for other x86 targets)
and chipset initialization. Those two routines have to be called
before U-Boot jumping to board_init_f in start.S.
The FspInit() will return several memory blocks called Hand Off
Blocks (HOBs) whose format is described in Platform Initialization
(PI) specification (part of the UEFI specication) to the bootloader.
Save this HOB address to the U-Boot global data for later use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use inline assembly codes to call FspNotify() to make sure parameters
are passed on the stack as required by the FSP calling convention.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This is the initial import from Intel FSP release for Queensbay
platform (Tunnel Creek processor and Topcliff Platform Controller
Hub), which can be downloaded from Intel website.
For more details, check http://www.intel.com/fsp.
Note: U-Boot coding convention was applied to these codes, so it
looks completely different from the original Intel release.
Also update FSP support codes license header to use SPDX ID.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Move GD_BIST from lib/asm-offsets.c to arch/x86/lib/asm-offsets.c
as it is x86 arch specific stuff. Also remove GENERATED_GD_RELOC_OFF
which is not referenced anymore.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel's Graphics Media Accelerator (GMA) is a generic name for a wide range
of video devices. Add code to set up the hardware on ivybridge. Part of the
init happens in native code, part of it happens in a 16-bit option ROM for
those nostalgic for the 1970s.
Signed-off-by: Simon Glass <sjg@chromium.org>
Option ROMs require a few additional descriptors. Add these, and remove the
enum since we now have to access several descriptors from assembler.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add code to set up the Local Advanced Peripheral Interrupt Controller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rename interrupt_init() in arch/x86/lib/pcat_interrupts.c to
i8259_init() and create a new interrupt_init() in
arch/x86/cpu/interrupt.c to call i8259_init() followed by a
call to cpu_init_interrupts().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Since cpu_init_interrupts() was moved out of cpu_init_r(), it is
useless to keep cpu_init_r() for x86, thus remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Currently cpu_init_interrupts() is called from cpu_init_r() to
setup the interrupt and exception of the cpu core, but at that
time the i8259 has not been initialized to mask all the irqs
and remap the master i8259 interrupt vector base, so the whole
system is at risk of being interrupted, and if interrupted,
wrong interrupt/exception message is shown.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Intel chips have a turbo mode where they can run faster for a short period
until they reach thermal limits. Add code to adjust and query this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Set up all the remaining pieces of the LPC (low-pin-count) peripheral in
PCH (Peripheral Controller Hub).
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards will want to do some setup before and after a PCI hose
is scanned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Define the reset base in config.mk so that it does not need to be calculated
twice in the link script. Also tidy up the START_16 and RESET_VEC_LOC values
to fit with this new approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some toolchains put the relocation data into separate sections. Adjust the
linker script to catch this case. Without relocation data, U-Boot will not
boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is not needed. Remove it to improve the generic init sequence
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is now required to add subdirectories in the x86 cpu Makefile. Add this
to fix a build breakage for chromebook_link.
Signed-off-by: Simon Glass <sjg@chromium.org>
The references of CONFIG_SYS_COREBOOT in arch/x86/cpu/coreboot/Makefile
are redundant because the build system descends into the directory
only when CONFIG_SYS_COREBOOT is defined.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Some CPUs of some architectures have SOC directories.
At present, the build system directly descends into SOC directories
from the top Makefile, but it should generally descend into each
directory from its parent directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
Implement SDRAM init using the Memory Reference Code (mrc.bin) provided in
the board directory and the SDRAM SPD information in the device tree. This
also needs the Intel Management Engine (me.bin) to work. Binary blobs
everywhere: so far we have MRC, ME and microcode.
SDRAM init works by setting up various parameters and calling the MRC. This
in turn does some sort of magic to work out how much memory there is and
the timing parameters to use. It also sets up the DRAM controllers. When
the MRC returns, we use the information it provides to map out the
available memory in U-Boot.
U-Boot normally moves itself to the top of RAM. On x86 the RAM is not
generally contiguous, and anyway some RAM may be above 4GB which doesn't
work in 32-bit mode. So we relocate to the top of the largest block of
RAM we can find below 4GB. Memory above 4GB is accessible with special
functions (see physmem).
It would be possible to build U-Boot in 64-bit mode but this wouldn't
necessarily provide any more memory, since the largest block is often below
4GB. Anyway U-Boot doesn't need huge amounts of memory - even a very large
ramdisk seldom exceeds 100-200MB. U-Boot has support for booting 64-bit
kernels directly so this does not pose a limitation in that area. Also there
are probably parts of U-Boot that will not work correctly in 64-bit mode.
The MRC is one.
There is some work remaining in this area. Since memory init is very slow
(over 500ms) it is possible to save the parameters in SPI flash to speed it
up next time. Suspend/resume support is not fully implemented, or at least
it is not efficient.
With this patch, link boots to a prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
The local advanced programmable interrupt controller is not used much in
U-Boot but we do need to set it up. Add basic support for this, which will
be extended as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
The built-in self test value should be checked before we continue booting.
Refuse to continue if there is something wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no need to explicitly write 'arch-coreboot' when including headers,
as when the arch directory points to coreboot the correct files will be
used.
Signed-off-by: Simon Glass <sjg@chromium.org>
The PCH (Platform Controller Hub) includes an LPC (Low Pin Count) device
which provides a serial port. This is accessible on Chromebooks, so enable
it early in the boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add simple PCI access routines for x86 which permit use before relocation.
The normal PCI stack is still used, but for pre-relocation use there can
only ever be a single hose. After relocation, fall back to the normal
access, although even then on x86 machines there is normally only a single
PCI bus.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for using PCI before SDRAM is available, using early malloc()
and global_data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We want access PCI earlier in the init sequence, so refactor the code so
that it does not require use of a BSS variable to work. This will allow us
to use early malloc() to store information about a PCI hose.
Common PCI code moves to arch/x86/cpu/pci.c and a new
board_pci_setup_hose() function is provided by boards to set up the (single)
hose used by that board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for CAR so that we have memory to use prior to DRAM init.
On link there is a total of 128KB of CAR available, although some is
used for the memory reference code.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 it is common to use 'post codes' which are 8-bit hex values emitted
from the code and visible to the user. Traditionally two 7-segment displays
were made available on the motherboard to show the last post code that was
emitted. This allows diagnosis of a boot problem since it is possible to
see where the code got to before it died.
On modern hardware these codes are not normally visible. On Chromebooks
they are displayed by the Embedded Controller (EC), so it is useful to emit
them. We must enable this feature for the EC to see the codes, so add an
option for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This board is a 'bare' version of the existing 'link 'board. It does not
require coreboot to run, but is intended to start directly from the reset
vector.
This initial commit has place holders for a wide range of features. These
will be added in follow-on patches and series. So far it cannot be booted
as there is no ROM image produced, but it does build without errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
The references of CONFIG_SYS_COREBOOT in arch/x86/cpu/coreboot/Makefile
are redundant because the build system descends into the directory
only when CONFIG_SYS_COREBOOT is defined.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This implementation has a 'cpu' prefix and returns a pointer to the string,
avoiding the need for copying.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The CPU identification happens in x86_cpu_init_f() and corresponding
fields are saved in the global data for later use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The built in self test value is available in register eax on start-up. Save
it so that it can be accessed later. Unfortunately we must wait until the
global_data is available before we can do this, so there is a little bit of
shuffling to keep it around.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some functions are missing prototypes. Fix those that are specific to x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Instead of an x86-specific cpu_init_f() function, use the normal U-Boot one
for this purpose. Also remove a useless/misleading comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Instead of having an x86-specific DRAM init function, adjust things so we
can use the normal one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This code is a little muddled, so tidy it up. Make sure that we put the
GDT in the right place and set it up properly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We should invalidate the TLB right at the start to ensure that we don't get
false address translations even though paging is disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This allows a board to do very early init, but no boards need to do this.
We may as well drop this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add code to jump to a 64-bit Linux kernel. We need to set up a flat page
table structure, a new GDT and then go through a few hoops in the right
order.
Signed-off-by: Simon Glass <sjg@chromium.org>
To permit information to be passed from the early U-Boot code to
board_init_f() we cannot zero the global_data in board_init_f(). Instead
zero it in the start-up code.
Signed-off-by: Simon Glass <sjg@chromium.org>
When building U-Boot with CONFIG_X86_RESET_VECTOR, the linking
process misses the resetvec.o and start16.o so it cannot generate
the rom version of U-Boot. The arch/x86/cpu/Makefile is updated to
pull them into the final linking process.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Until now building the x86 arch boards required 32-bit toolchain. As
many x86_64 toolchains come with 32-bit support (multilib) that's a
good idea to enable build with such toolchains.
The change required was to specify the usage of 32-bit explicitly to
the compiler and the linker (-m32 and -m elf_i386 flags) and locate
the right libgcc path.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
U-Boot has supported two kinds of asm-offsets.h.
One is generic for all architectures and its source is located at
./lib/asm-offsets.c.
The other is SoC specific and its source is under SoC directory.
The problem here is that only boards with SoC directory can use
the asm-offsets infrastructure.
Putting asm-offsets.c right under CPU directory does not work.
Now a new demand is coming. PowerPC folks want to use asm-offsets.
But no PowerPC boards have SoC directory.
It seems inconsistent that some boards add asm-offsets.c to SoC
directoreis and some to CPU directories.
It looks more reasonable to put asm-offsets.c under arch/$(ARCH)/lib.
This commit merges asm-offsets.c under SoC directories into
arch/$(ARCH)/lib/asm-offsets.c.
By the way, I doubt the necessity of some entries in asm-offsets.c.
I am leaving refactoring to the board maintainers.
Please check "TODO" in the comment blocks in
arch/{arm,nds32}/lib/asm-offsets.c.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Yuantian Tang <Yuantian.Tang@freescale.com>
Now that nothing uses CONFIG_ARCH_DEVICE_TREE, stop defining it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Coreboot provides a lot of useful timing information. Provide a facility
to add this to bootstage on start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tidy up some old broken and unneeded implementations. These are not used
by coreboot or anything else now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Michael Spang <spang@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
This timer runs at a rate that can be calculated, well over 100MHz. It is
ideal for accurate timing and does not need interrupt servicing.
Tidy up some old broken and unneeded implementations at the same time.
To provide a consistent view of boot time, we use the same time
base as coreboot. Use the base timestamp supplied by coreboot
as U-Boot's base time.
Signed-off-by: Simon Glass <sjg@chromium.org>base
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'Starting linux' message appears twice in the code, but both call
through the same place. Unify these and add calls to bootstage to
mark the occasion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Spang <spang@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
panic_puts() can be called in early boot to display a message. It might
help with early debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Wai-Hong Tam <waihong@chromium.org>
Several files use the global_data pointer without declaring it. This works
because the declaration is currently a NOP. But still it is better to
fix this so that x86 lines up with other archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since we don't have real-mode code now, we can remove this chunk of the link
script.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
The intention of the memory init code is that it should work the same with
CONFIG_SYS_GENERIC_BOARD and without. This is tricky because dram_init()
is called prior to relocation with generic board (matching other archs)
and after relocation without generic board.
Adjust the init sequence so that dram_init() is not called in the generic
board case, which seems like the easiest fix for now. Also ensure that
relocation addresses are still calculated.
Signed-off-by: Simon Glass <sjg@chromium.org>
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
Refactor linker-generated array code so that symbols
which were previously linker-generated are now compiler-
generated. This causes relocation records of type
R_ARM_ABS32 to become R_ARM_RELATIVE, which makes
code which uses LGA able to run before relocation as
well as after.
Note: this affects more than ARM targets, as linker-
lists span possibly all target architectures, notably
PowerPC.
Conflicts:
arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
board/ait/cam_enc_4xx/u-boot-spl.lds
board/davinci/da8xxevm/u-boot-spl-da850evm.lds
board/davinci/da8xxevm/u-boot-spl-hawk.lds
board/vpac270/u-boot-spl.lds
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
At present BSS data is including in the image, which wastes binary space.
Remove it by rearranging the sections so that BSS is last.
Signed-off-by: Simon Glass <sjg@chromium.org>
With this symbol we can easy append something (e.g. an FDT) to the U-Boot
binary and access it from within U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to access the timer before U-Boot has relocated
so that we can fully support bootstage.
Add new global_data members to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The memory layout calculations are done in calculate_relocation_address(),
and coreboot has its own version of this function. But in fact all we
really need is to set the top of usable RAM, and then the base version
will work as is.
So instead of allowing the whole calculate_relocation_address() function
to be replaced, create board_get_usable_ram_top() which can be used by
a board to specify the top of the area where U-Boot relocations to.
Signed-off-by: Simon Glass <sjg@chromium.org>
Invert the polarity of this option to simplify the Makefile logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Gabe Black <gabeblack@chromium.org>
This x86 CPU variant is no longer required as the boards that use it have
been removed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
Move this field into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add arch/x86/cpu/cpu.c changes after Graeme's comments]
Signed-off-by: Tom Rini <trini@ti.com>
We currently assume that the global data pointer is at the start of
struct global_data. We want to remove this restriction, and it is
easiest to do this in C.
Remove the asm code and add equivalent code in C.
This idea was proposed by Graeme Russ here:
http://patchwork.ozlabs.org/patch/199741/
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Apply Graeme Russ' comments
http://patchwork.ozlabs.org/patch/206305/ here, re-order]
Signed-off-by: Tom Rini <trini@ti.com>
The function setup_pcat_compatibility() is weak and implemented as empty
function in board.c hence we don't have to override that with another
empty function.
monitor_flash_len is unused, drop it.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
... because that information is already "encoded" in the directory name.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Some systems (like Google Link device) provide the ability to keep a
history of the target CPU port80 accesses, which is extremely handy
for debugging. The problem is that the EC handling port 80 access is
orders of magnitude slower than the AP. This causes random loss of
trace data.
This change allows to throttle port 80 accesses such that in case the
AP is trying to post faster than the EC can handle, a delay is
introduced to make sure that the post rate is throttled. Experiments
have shown that on Link the delay should be at least 350,000 of tsc
clocks.
Throttling is not being enabled by default: to enable it one would
have to set MIN_PORT80_KCLOCKS_DELAY to something like 400 and rebuild
the u-boot image. With upcoming EC code optimizations this number
could be decreased (new new value should be established
experimentally).
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Some u-boot modules rely on availability of get_ticks() and
get_tbclk() functions, reporting a free running clock and its
frequency respectively. Traditionally these functions return number
and frequency of timer interrupts.
Intel's core architecture processors however are known to run the
rdtsc instruction at a constant rate of the so called 'Max Non Turbo
ratio' times the external clock frequency which is 100MHz. This is
just as good for the timer tick functions in question.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This will write magic value to APMC command port which
will trigger an SMI and cause coreboot to lock down
the ME, chipset, and CPU.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Coreboot was always using MTRR 7 for the write-protect
cache entry that covers the ROM and U-boot was removing it.
However with 4GB configs we need more MTRRs for the BIOS
and so the WP MTRR needs to move. Instead coreboot will
always use the last available MTRR that is normally set
aside for OS use and U-boot can clear it before the OS.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This helps us monitor boot progress and determine where U-Boot dies if
there are any problems.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
These were removed, but actually are useful.
Cold means that we started from a reset/power on.
Warm means that we started from another U-Boot.
We determine whether u-boot on x86 was warm or cold booted (really if
it started at the beginning of the text segment or at the ELF entry point).
We plumb the result through to the global data structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Because calculate_relocation_address now uses the e820 map, it will be able
to avoid addresses over 32 bits and regions that are at high addresses but
not big enough for U-Boot. It also means we can remove the hack which
limitted U-Boot's idea of the size of memory to less than 4GB.
Also take into account the space needed for the heap and stack, so we avoid
picking a very small region those areas might overlap with something it
shouldn't.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
U-boot is unable to actually use that memory and it can
cause problems with relocation if it tries to.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This cleans up the rom caching optimization implemented in coreboot (and
needed throughout U-Boot runtime).
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This way when that dram "banks" are displayed, there's some useful information
there. The number of "banks" we claim to have needs to be adjusted so that it
covers the number of RAM e820 regions we expect to have/care about.
This needs to be done after "RAM" initialization even though we always run
from RAM. The bd pointer in the global data structure doesn't automatically
point to anything, and it isn't set up until "RAM" is available since, I
assume, it would take too much space in the very constrained pre-RAM
environment.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This change turns on the code which allows u-boot to add
timestamps to the timestamp table created by coreboot.
Since u-boot does not use the tsc_t like structure to represent
HW counter readings, this structure is being replaced by 64 bit
integer.
The timestamp_init() function is now initializing the base timer
value used by u-boot to calculate the HW counter increments.
Timestamp facility is initialized as soon as the timestamp table
pointer is found in the coreboot table. The u-boot generated
timer events' ID will start at 1000 to clearly separate u-boot
events from coreboot events in the timer trace.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The microsecond timer is not currently implemented, but add a dummy
implementation for now.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function provides an opportunity for some last minute cleanup and
reconfiguration before control is handed over to Linux. It's possible this
may need to do something in the future, but for now it's left empty. It's set
up as a weak symbol so it can be overridden if necessary on a case by case
basis.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for decoding tags for GPIOs, compile/build info, cbmem and
other features.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
sysinfo.c only contains the lib_sysinfo data structure which
is used/filled by tables.c. This split was introduced by importing
code from libpayload originally, but to keep the code simple, add
the single line of actual code to tables.c
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
A hook is installed to configure PCI bus bridges as they encountered by u-boot.
The hook extracts the secondary bus number from the bridge's config space and
then recursively scans that bus.
On Coreboot, the PCI bus address space has identity mapping with the
physical address space, so declare it as such to ensure that the "pci_map_bar"
function used by some PCI drivers is behaving properly. This fixes the
EHCI PCI driver initialization on Stumpy.
This was tested as follows:
Ran the PCI command on Alex, saw devices on bus 0, the OXPCIe 952 on
bus 1, and empty busses 2 through 5. This matches the bridges
reported on bus 0 and the PCI configuration output from coreboot.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
U-boot needs a host controller or "hose" to interact with the PCI busses
behind them. This change installs a host controller during initialization of
the coreboot "board" which implements some of X86's basic PCI semantics. This
relies on some existing generic code, but also duplicates a little bit of code
from the sc520 implementation. Ideally we'd eliminate that duplication at some
point.
It looks like in order to scan buses beyond bus 0, we'll need to tell u-boot's
generic PCI configuration code what to do if it encounters a bridge,
specifically to scan the bus on the other side of it.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
coreboot.c and coreboot_pci.c don't contain board specific but only
coreboot specific code. Hence move it to the coreboot directory in
arch/x86/cpu (which should probably be moved out of cpu/ in another
commit)
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
When running from coreboot we don't want this code.
This version works by ifdef-ing out all of the code that would go
into those sections and all the code that refers to it. The sections are
then empty, and the linker will either leave them empty for the loader
to ignore or remove them entirely.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Putting global data on the stack simplifies the init process (and makes it
slightly quicker). During the 'flash' stage of the init sequence, global
data is in the CAR stack. After SDRAM is initialised, global data is copied
from CAR to the SDRAM stack
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
So it can be used as a type in struct global_data and remove an ugly typecast
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Building the eNET_SRAM board fails for me:
sc520_timer.c: In function 'sc520_udelay':
sc520_timer.c:81:7: error: variable 'temp' set but not used
[-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
make[1]: *** [sc520_timer.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use the base address of the 'F' segment as a pointer to the global data
structure. By adding the linear address (i.e. the 'D' segment address) as
the first word of the global data structure, the address of the global data
relative to the 'D' segment can be found simply, for example, by:
fs movl 0, %eax
This makes the gd 'pointer' writable prior to relocation (by reloading the
Global Desctriptor Table) which brings x86 into line with all other arches
NOTE: Writing to the gd 'pointer' is expensive (but we only do it
twice) but using it to access global data members (read and write) is
still fairly cheap
--
Changes for v2:
- Rebased against changes made to patch #3
- Removed extra indent
- Tweaked commit message
Move the relocation offset calculation out of assembler and into C. This
also paves the way for the upcoming init sequence simplification by adding
the board_init_f_r flash to RAM transitional function
--
Changes for v2:
- Added commit message
- Minor adjustment to new stack address comment
The inline assembler is ugly and uses hard coded magic numbers. Make it more
elegant to allow cleaner implementation of future GDT related patches. The
compiler seems smart enough to generate the same code anyway
--
Changes for v2:
- Rebased against revised patch #3
- Use GDT size define instead of magic number
- Added commit message
Also approximate the size of RAM using the largest RAM address available
in the tables. There may be areas which are marked as reserved which are
actually at the end of RAM.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
This change also forces the lib_sysinfo structure to be in the .data
section. Otherwise it ends up in the .bss section. U-boot assumes that it
doesn't need to copy it over during relocation, and instead fills that
whole section with zeroes. If we really were booting from ROM that would be
appropriate, but we need some information from the coreboot tables (memory
size) before then and have to fill that structure before relocation. We
skirt u-boot's assumption by putting this in .data where it assumes there
is still read only but non-zero data.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Add a target for running u-boot as a coreboot payload in boards.cfg, a
board, CPU and a config. This is a skeleton implementation which always
reports the size of memory as 64 MB.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
By adding a multiboot header, U-Boot can be loaded by GRUB2. Using GRUB2 to
bootstrap U-Boot is useful for using an existing BIOS to get an initial
U-Boot port up and running before implementing the low-level reset vector
code, SDRAM init, etc. and overwriting the BIOS
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
Partial linking allows weak functions to be overridden in files containing
only one function. Moving the sc520 override of reset_cpu gets rid of an
ugly #ifdef
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
