Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().
Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The BOOT_TARGET_DEVICES list for distro_bootcmd was hard-coded to assume
that all boot devices are available/enabled in the configuration,
thus ignoring the actual config settings. The config_distro_bootcmd.h
header file specifically has compile-time checks to detect such problems.
To allow disabling USB, SCSI, etc. in custom lx2160a board configs,
make it depend on the config settings and use only the enabled features.
Signed-off-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Use the complete 512kb (4 blocks) nand partition reserved for u-boot
environment instead of just the first block, this allows the module to
have a working environment even if 3 blocks are bad.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Now that single defconfig can be used for booting J721E EVM and
SK, default device tree will not work for selecting dtb for
kernel. Update the findfdt env to select right dtb based on
board_name env variable.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
There are no boards that define CONFIG_SYS_RESET_ADDR, so drop the
remaining comments referencing it and also the config_whitelist.txt entry.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: thomas@wytron.com.tw
This driver adds support for the keyboard on Apple Silicon laptops.
The controller for this keyboard sits on an SPI bus and uses an
Apple-specific HID over SPI protocol. The packets sent by this
controller for key presses and key releases are fairly simple and
are decoded directly by the code in this driver and converted into
standard Linux keycodes. The same controller handles the touchpad
found on these laptops. Packets for touchpad events are simply
ignored.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert
to Driver Model and use uclass mvgbe and the compatible driver M88E1118R
to bring up Ethernet.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- As the result of the migration to Driver Model, this u-boot image has
grown substantially (about 100K, give or take). The old envs location
at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K).
- Miscellaneous changes: Move constants to .c file and remove header file
board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to
keep u-boot image under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Dockstar board has the network chip Marvell 88E1116R. Convert to
Ethernet driver model, and use uclass mvgbe and the compatible driver
M88E1118R to bring up Ethernet.
- Add CONFIG_DM_ETH and associated configs.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Add CONFIG_PHY_MARVELL to properly configure the network.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Miscellaneous changes: Move constants to .c file and remove
header file board/Seagate/dockstar/dockstar.h, use
CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, add CONFIG_HUSH_PARSER, use BIT macro, and cleanup comments.
- Note: This patch is a RESEND for a previous patch:
https://patchwork.ozlabs.org/project/uboot/patch/20210812051854.1340-2-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Miscellaneous changes: Move constants to .c file and remove header file
board/iomega/iconnect/iconnect.h. Add CONFIG_HUSH_PARSER, use BIT macro,
and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Globalscale Technologies Dreamplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network
port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned,
could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/dreamplug/dreamplug.h, cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE
Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is defined based on two other CONFIGs for all boards except sandbox
and durian.
For sandbox the value does not matter. For durian the value seems
excessive.
Drop the option completely, to simplify configuration and reduce the
number of things we need to convert to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_IDE_MAXBUS
CONFIG_SYS_IDE_MAXDEVICE
CONFIG_SYS_ATA_BASE_ADDR
CONFIG_SYS_ATA_STRIDE
CONFIG_SYS_ATA_DATA_OFFSET
CONFIG_SYS_ATA_REG_OFFSET
CONFIG_SYS_ATA_ALT_OFFSET
CONFIG_SYS_ATA_IDE0_OFFSET
CONFIG_SYS_ATA_IDE1_OFFSET
CONFIG_ATAPI
CONFIG_IDE_RESET
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move setting the default boot command to the
apalis/colibri_imx6_defconfig. It allows replacing the command
without code modification.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The Linux Kernel Image size for arm64 is still growing.
A Kernel with 54 MB at load address 0x80280000 overlaps
with fdt_addr at 0x83000000. So let's increase it to 0x84000000
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Commit 72d81360aa ("global: Convert CONFIG_LOADADDR to
CONFIG_SYS_LOADADDR") dropped the usage of LOADADDR and replaced it with
SYS_LOADADDR.
Use the correct macro in environment by replacing CONFIG_LOADADDR with
CONFIG_SYS_LOADADDR.
Fixes: d75ebf3482 ("imx: ventana: fix splash logo drawing")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Add fdt_addr_r fdtfile which used by distro boot, and cleanup legacy
environment variables.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
We changed to single flash.bin now. So dfu_alt_info should be modified
to reflect this change.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The PDK2 board is capable of running both 100M and 1G ethernet. However,
the i.MX6 has only one ethernet MAC, so it is possible to configure
either 100M or 1G Ethernet. In case of 100M option, the PHY is on the
SoM and the signals are routed to a RJ45 port. For 1G the PHY is on
the PDK2 board with another RJ45 port. 100M and 1G ethernet use
different signal pins from the i.MX6, but share the MDIO bus.
This SoM board combination is used to demonstrate how to enable 1G
ethernet configuration.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Use the complete 512kb (4 blocks) nand partition reserved for u-boot
environment instead of just the first block, this allows the module
to have a working environment even if 3 blocks are bad.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Adds support for SUNIV and the F1C100s.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Remove some pointless #ifdefs from this file, as there are quite too
many of them already.
Some definitions don't really hurt to have in any case, so remove the
pointless CONFIG_MMC guard around CONFIG_MMC_SUNXI_SLOT.
The BOARD_SIZE_LIMIT applies regardless of ARM64 or not (now), so remove
that guard as well. The maximum number of MMC devices does not depend on
CONFIG_ENV_IS_IN_MMC, so move that out to simplify the file.
Last but not least CONFIG_SPL_BOARD_LOAD_IMAGE serves no real purpose
anymore: it's unconditionally defined for all sunxi boards, and protects
nothing applicable outside of sunxi code anymore. Just remove it.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Field fail-safe u-boot update procedure for pg-wcom boards is defined and
implemented by patch: 59b3403.
This patch invokes the update procedure for pg-wcom-ls102x designs during
early misc_init_f execution.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The GoFlex Home board has the network chip Marvell 88E1116R.
Use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: use CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
With Ethboot support in SPL, network stack requires more BSS area, so
increase BSS max size to 16K
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Today the bootcount is not managed by the Linux kernel for STM32MP15 as
we don't have driver to update the used backup register in TAMP and the
recovery command still executes the normal bootcmd with
'altbootcmd=run bootcmd'.
So the bootcount feature is never used, the config CONFIG_BOOTCOUNT_LIMIT
and the associated environment variable 'altbootcmd' can be removed to
reduce the U-Boot size.
Each boards can re-enable this feature later in their defconfig, if it is
needed, with the expected backend, for example CONFIG_BOOTCOUNT_GENERIC
or CONFIG_BOOTCOUNT_ENV.
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the following to Kconfig:
CONFIG_AT91_EFLASH
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Prepare migration to Kconfig.
CONFIG_SYS_MAX_FLASH_BANKS_DETECT becomes boolean and
CONFIG_SYS_MAX_FLASH_BANKS define the MAX size, also used
for detection when CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
(CFI_MAX_FLASH_BANKS = CONFIG_SYS_MAX_FLASH_BANKS).
CONFIG_SYS_MAX_FLASH_BANKS become mandatory when
CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
The am335x-ice-v2 board's Ethernet ports can be configured
in 'MII' or 'RMII' mode to be connected to 'PRUSS' or 'CPSW'
Ethernet subsystems.
This patch sets the environment variable 'ice_mii' to
'mii' or 'rmii' accordingly. Based on that we choose the
appropriate board devicetree i.e. 'am335x-ice-v2.dtb' or
'am335x-ice-v2-prueth.dtb'.
Since there are 2 Ethernet ports with 2 modes, there can be 4
configurations but for now we consider both ports in different modes
to be an invalid configuration and prevent boot in that case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Amjad: use overlay instead of using new am335x-ice-v2-prueth.dtb]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make prueth_is_mii be marked __maybe_unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
BOOT_TARGET_DEVICES should only be added if the corresponding u-boot
command is enabled otherwise the build will fail.
Signed-off-by: Piotr Kubik <piotr_kubik@vp.pl>
These hardcoded values were calculated from CONFIG_SPL_TEXT_BASE macro. Now
this macro is configurable via Kconfig, so calculate values 0x0030/0x4030
at compile time via CONFIG_SPL_TEXT_BASE option. Values 0x0030/0x4030
represents offset of CONFIG_SPL_TEXT_BASE from address 0x40000000.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Memory layout in the comment is from Armada XP platform which uses load
address 0x40004030. DB-88f6720 is Armada 375 platform which uses same load
address as Armada 38x which is 0x40000030.
Currently SPL support for Armada 375 is unfinished and does not work. There
is missing Serdes initialization and DDR3 training code. So nobody noticed
that CONFIG_SPL_* options are not correct.
Fix at least CONFIG_SPL_TEXT_BASE constant and remove incorrect comments
about memory layout. So it is not misleading.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
After the conversion to DM the SD card shows up as 'mmc 2'
device.
Adjust the 'mmcdev' and the distro command 'func' accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Enable support for USB and USB storage on the UDOO Neo.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In AOSP, both VIM3 and VIM3L have 2 bootloader flavors,
depending on A/B enablement.
For example, for vim3l, the naming is:
- u-boot_kvim3l_noab.bin : legacy support
- u-boot_kvim3l_ab.bin : A/B support
Prepare a defconfig to support u-boot_kvim3_ab.bin and
u-boot_kvim3l_ab.bin.
This is identical to khadas-vim3{l}_ab_android but will be updated in
the next commit.
Also update partitioning tables for A/B support.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-4-mkorpershoek@baylibre.com
This allows us to define extra board variables, such as "board" and
"board_name".
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-2-mkorpershoek@baylibre.com
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-7-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze is one the last two users of the CONFIG_SYS_RESET_ADDRESS
macro (the other is arch/powerpc/cpu/mpc8xx/cpu.c, but the macro is not
defined anywhere in powerpc code, so it should be removed there too).
Replace CONFIG_SYS_RESET_ADDRESS usage in start.S with
CONFIG_SYS_TEXT_BASE. If the reset address should really be
user-configurable, a new Kconfig option could be added.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-6-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The memory layout is taken from the device tree passed to us by
m1n1, so there is no need to define this.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The SMSC driver is using the old driver model.
Init the virtio system in vexpress64.c so that the network device is
discovered.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Move env var address values to #defines so they can be reused elsewhere.
Rename env var names to those recommended in the README and modify
addresses to allow more space for the kernel.
Fix issue where fdt is called with invalid arguments when booting
without a ramdisk.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Rename from vexpress_aemv8a.h -> vepxress_aemv8.h as new FVPs may not be
v8-A. No change in behavior.
This is towards future work to enable support for the FVP_BaseR.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
When using a recent kernel with a bunch of compiled-in
stuff the kernel image easily becomes bigger than 8 MB
yielding this error:
Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Fix this by bumping to SZ_64MB.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
-----BEGIN PGP SIGNATURE-----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=YdSB
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request of efi-next
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
This converts the following to Kconfig:
CONFIG_JFFS2_DEV
CONFIG_JFFS2_LZO
CONFIG_JFFS2_NAND
CONFIG_JFFS2_PART_OFFSET
CONFIG_JFFS2_PART_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_88F5182
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_IS_OPENRD_CLIENT
CONFIG_BOARD_IS_OPENRD_ULTIMATE
CONFIG_D2NET_V2
CONFIG_FEROCEON
CONFIG_FEROCEON_88FR131
CONFIG_INETSPACE_V2
CONFIG_KW88F6192
CONFIG_KW88F6281
CONFIG_KW88F6702
CONFIG_NET2BIG_V2
CONFIG_NETSPACE_LITE_V2
CONFIG_NETSPACE_MAX_V2
CONFIG_NETSPACE_MINI_V2
CONFIG_NETSPACE_V2
CONFIG_SHEEVA_88SV131
At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.
Signed-off-by: Tom Rini <trini@konsulko.com>
The only place we use CONFIG_CPU_ARMV8 was in the arm_dcc serial driver.
Switch this to CONFIG_ARM64 today, and if in the future we need finer
granularity tuning here, a new CONFIG_SERIAL option needs to be
introduced.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one of two ways. The first way is that it
is defined to a static value, of an unsigned long size. The second way
is that it is defined to something, typically a function, to determine
this value at run time.
However, in a few cases that function returns a static value. Change
that to using the static value directly.
In the case of using something at run time, convert everything to using
a function of the same name and prototype. This will allow for further
cleanups.
Finally, we have a few cases where the function is just not used, so
drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_CLK_FREQ_C100 and CONFIG_SYS_CLK_FREQ_C110 are
only used in one place and not changed by the board config file. Move
these out of the CONFIG namespace and in to the CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish this conversion we need to add a symbols for
SPL_SYS_NAND_SELF_INIT and TPL_SYS_NAND_SELF_INIT as there are cases
there where we need to, or need to not, use that framework as things
stand.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of CONFIG_SYS_FDT_ADDR this was being used to modify the
default value of fdt_addr / fdt_addr_r, which is not something to expose
in this manner and is not otherwise done. The case of SYS_ENV_ADDR is
similar but only done on the pic32mzdask platform, for scriptaddr.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
This is removing unused defines and correcting the default value to be
0x0 as we are a hex symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.
For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.
For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
In order to do this conversion, expose this option to the user and
use "save" not "safe" in the text.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_RPMB
This fixes a few platforms where the option was not taking effect as
intended.
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used as part of configuring the default environment for a
number of platforms. However, it is always set to 1 and the only time
it is part of Kconfig, it is used in a hard-coded manner. Hard-code the
value in the environment instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VIDEO_LOGO
Note that this option depends on CONFIG_DM_VIDEO now, since cfb_console is
deprecated. The only relevant code is now in splash.c
Drop the check for DM_VIDEO in that file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable SPL support in Kconfig and add some related option in
rk3568_common.h
Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com>
Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The resync of the device trees from Linux 5.16-rc3 caused aliases
to appear on the MMC devices which changed the numbering.
This changed the default boot device and caused boot failure.
Update the mmcdev variable to reflect the new aliases.
Signed-off-by: Adam Ford <aford173@gmail.com>
CONFIG_SYS_ATA_PORT_ADDR is not used in the code anymore. Drop it and use
ATA_PORT_ADDR() locally instead.
Drop CONFIG_IDE_RESET_ROUTINE and CONFIG_IDE_SWAP_IO which are also
unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used by sandbox since it uses driver model for the timer.
Drop it.
Also update the tools_only build to avoid build errors, since it does
actually build U-Boot too. Enable DM so we can use CONFIG_TIMER,
disable EFI_LOADER to avoid an error about board_quiesce_devices() and
disable NET to avoid having to define CONFIG_AVB_BUF_ADDR
Signed-off-by: Simon Glass <sjg@chromium.org>
This can go in the related header file. Drop the CONFIG option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add boot command "bootcmd_ram" to support autoboot from RAM.
This feature could be useful at the very initial state of chip design
when there is only a minimal set of peripheral. (e.g. without mmc and mac ..etc)
The kernel image is default to be loaded at 0x2000000 via debug port,
and the following script serves as an example:
spl()
{
cmd="riscv64-linux-gdb -q \
-ex \"target remote $host:$port\" \
-ex \"load\" \
-ex \"thread apply all set \\\$pc=&_start\" \
-ex \"thread apply all set \\\$a0=\\\$mhartid\" \
-ex \"thread apply all set \\\$a1=<dtb address>\" \
-ex \"restore u-boot.itb binary 0x200000\" \
-ex \"restore Image binary 0x2000000\" \
-ex \"c\" \
spl/u-boot-spl
"
echo $cmd
eval $cmd
}
The address where the kernel is loaded can be altered by
changing the value of KERNEL_IMAGE_ADDR.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM
This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LCD_DT_SIMPLEFB
This patch also renames this config to CONFIG_FDT_SIMPLEFB as the code in
common/lcd_simplefb.c support CONFIG_LCD and CONFIG_VIDEO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Using mmc.dtbo from rpi-firmware to switch the controller for the SD
card slot from sdhci to sdhost causes the numbering to change; the
SD card is then not recognized at boot. Add to the range checked.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
If bootloader was updated without running oem format, reboot will cause
boot loop because the SYSTEM stage fails.
Add a final PANIC stage running fastboot to permit recovery.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This can lead to GPT and BCB errors even if fastboot was selected early
by usb rom boot and the eMMC is blank/invalid.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
AST2600 leverages the FIT hash/signature verification to fulfill
secure boot trust chain. To improve the performance and save SW
code size for those crypto operations, the two HW crypto engine,
HACE and ACRY, are enabled.
However, both of the engines can only access to data stored in
DRAM space. Therefore, we need to move the FIT image into DRAM
before the booting.
This patch update the CONFIG_BOOTCOMMAND to execute the pre-defined
ENV variable which consists of FIT image copy to memory and booting.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Use a text file for the environment instead of the #define settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
This is a complicated set of #defines and it is painful to convert to a
text file. We can (once pending patches are applied) provide the same
functionality with bootmethod. Drop this for sandbox to allow conversion
to a text-file environment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Fix dfu_alt_info to use nor1 instead of the device name.
This reverts a part of commit 59bd18d4c4 ("configs: synquacer:
Remove mtdparts settings and update DFU setting") because the
commit a4f2d83414 ("mtd: spi: nor: force mtd name to "nor%d"")
changed the mtd device naming scheme to nor%d.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This symbol has been functionally dead for a long time. Remove the last
and recent re-introductions of setting it, and update the whitelist so
it will not be re-introduced again.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_TRACE
CONFIG_TRACE_BUFFER_SIZE
CONFIG_TRACE_EARLY
CONFIG_TRACE_EARLY_ADDR
CONFIG_TRACE_EARLY_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH
CONFIG_ENV_IS_NOWHERE
CONFIG_ENV_OFFSET
CONFIG_ENV_OVERWRITE
CONFIG_ENV_SECT_SIZE
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Signed-off-by: Tom Rini <trini@konsulko.com>
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
In some part of STM32MP15 support the CONFIG_TFABOOT can be replaced
by other config: CONFIG_ARMV7_PSCI and CONFIG_ARM_SMCCC.
This patch also simplifies the code in cpu.c, stm32mp1_ram.c and
clk_stml32mp1.c as execution of U-Boot in sysram (boot without SPL and
without TFA) is not supported: the associated initialization code is
present only in SPL.
This cleanup patch is a preliminary step to support SPL load of OP-TEE
in secure world, with SPL in secure world and U-Boot in no-secure world.
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add a configuration file "stm32mp15_st_common.h" to handle the
STMicroelectronics boards configuration and rename stm32mp1.h to
"stm32mp15_common.h" to handle the generic STM32MP15x series configuration.
The configuration file "dh_stm32mp1.h" is also renamed to
"stm32mp15_dh_dhcom" for the configuration of board based on the
dhelectronics STM32MP15x SOM.
In the STMicroelectronics board configuration the default bootcmd
"bootcmd_stm32mp" is updated to only select the extlinux file found on
SD-Card on STM32MP15x EV1 for boot from NOR device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LS1046A-QDS has CONFIG_SPI_FLASH_SST, CONFIG_SPI_FLASH_EON and
CONFIG_SPI_FLASH_STMICRO defines present in header. Move these entries
from header to defconfigs.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable support for update over EFI UpdateCapsule mechanism. This board
doesn't support setting EFI variables after ExitBootservices().
Therefore, we are also enabling EFI_IGNORE_OSINDICATIONS.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F
CONFIG_BOARD_LATE_INIT
CONFIG_DISPLAY_BOARDINFO
CONFIG_DISPLAY_BOARDINFO_LATE
Signed-off-by: Tom Rini <trini@konsulko.com>
Samsung S9 SM-G9600 - Snapdragon SDM845 version of the phone,
for China \ Hong Kong markets.
Has unlockable bootloader, unlike SM-G960U (American market version),
which allows running u-boot as a chain-loaded bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Hi-end qualcomm chip, introduced in late 2017.
Mostly used in flagship phones and tablets of 2018.
Features:
- arm64 arch
- total of 8 Kryo 385 Gold / Silver cores
- Hexagon 685 DSP
- Adreno 630 GPU
Tested only as second-stage bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Add support for Apple's M1 SoC that is used in "Apple Silicon"
Macs. This builds a basic U-Boot that can be used as a payload
for the m1n1 boot loader being developed by the Asahi Linux
project.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add MAINTAINERS entry]
- Add and enable watchdog driver
- Prepare for SYSRESET driven AXP poweroff
- Prepare for SoCs without MMC2
- Some fixes for extending SPL (SPL-DM for RISC-V)
- Some preparations for proper VBUS management
- Fix secure monitor move
commit 1ebfc0c631 ("sunxi: A23/A33/H3: Move sun8i secure monitor to
SRAM A2") attempted to move the secure monitor to SRAM A2. But not all
sun8i SoCs have SRAM A2, so a check was put in for SUNXI_SRAM_A2_SIZE to
avoid breaking the other SoCs.
However, because the header providing SUNXI_SRAM_A2_SIZE was not
included, this unintentionally skipped the new definitions on all SoCs.
Fix this by including the right header.
Fixes: 1ebfc0c631 ("sunxi: A23/A33/H3: Move sun8i secure monitor to SRAM A2")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Instead of declaring CONFIG_SPL_DRIVERS_MISC in board config header,
select it in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Instead of declaring CONFIG_SYS_MALLOC_SIMPLE dependant on
CONFIG_SPL_BUILD in board config header, select
CONFIG_SPL_SYS_MALLOC_SIMPLE in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
