Convert clock manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get clock manager base address from DT node instead of using
#define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert system manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get system manager base address from DT node instead of
using #define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert reset manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get reset manager base address from DT node instead of using
#define.
spl_early_init() initializes the DT setup. So, move spl_early_init() to
beginning of function and before get base address from DT.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add u-boot,dm-pre-reloc for sysmgr and clkmgr nodes to use it in SPL.
In preparation to get base address from DT.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Import the Khadas VIM3L device-tree from [1]
[1] e42617b825f8 ("Linux 5.5-rc1")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
It's true that booting normally doesn't take long enough for the
register to roll (which actually happens in a little over an hour, not
just a few seconds). However, the counter starts at power-on, and if
the board is held in reset to be booted over USB, one actually risks
hitting wrap-around during boot, which can both result in too short
delays (if the "st += delay" calculation makes st small) and
theoretically also unbound delays (if st ends up being UINT_MAX and
one just misses sampling digctl_microseconds at that point).
It doesn't take more code to DTRT, and once bitten, twice shy.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Engicam i.CoreM6 1.5 Quad/Dual MIPI dtsi is reusing fec node
from Engicam i.CoreM6 dtsi but have sampe copy of phy-reset-gpio
and phy-mode properties.
So, drop this phy reset methods from imx6qdl-icore-1.5 dsti file.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Similar fix has merged for i.Core MX6Q but missed to update for DL.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync Engicam device tree file from v5.4 linux-next.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The data sheet says that the DIV field cannot change while the CLKGATE
bit is set or modified. So do it a little more carefully, by first
clearing the bit, waiting for that to appear, then setting the DIV
field.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The comment says to clear the bypass bit, but in fact it sets it, thus
selecting ref_xtal. And the next line of code does not set the divider
to 12, but to (the reset value of) 1.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
I tried clearing a bit by writing to hw_clkctrl_gpmi_clr, then
busy-waiting for it to actually clear. My board hung. The data sheet
agrees, these registers do not have _set, _clr, _tog, so fix up the
definitions. git grep -E 'clkctrl_(gpmi|ssp[0-9])_' says that nobody
uses those non-existing ops registers.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Add info about supported i.MX7, improve details the usage of
bcbonly subcommand.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
In cases when the same SPL should run on boards with i.MX8MM, that
differ in DDR configuration, it is necessary to try different
parameters and check if the training done by the firmware suceeds or
not.
Therefore we return the DDR training/initialization success to the
upper layer in order to be able to retry with different settings if
necessary.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In the case of i.MX6 and i.MX7 family SoCs it is safe (from an errata
point of view) to use thumb2 by default to save space.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently imx-specific bootaux command doesn't support ELF format
firmware for Cortex-M4 core.
This patches introduces a PoC implementation of handling elf firmware
(load_elf_image_phdr() was copy-pasted from elf.c just for PoC).
ELF64 binaries isn't supported yet.
This has the advantage that the user does not need to know to which
address the binary has been linked to. However, in order to handle
and load the elf sections to the right address, we need to translate the
Cortex-M4 core memory addresses to primary/host CPU memory
addresses (Cortex A7/A9 cores).
This allows to boot firmwares from any location with just using
bootaux, e.g.:
> tftp ${loadaddr} hello_world.elf && bootaux ${loadaddr}
Similar translation table can be found in the Linux remoteproc
driver [1].
[1] https://elixir.bootlin.com/linux/latest/source/drivers/remoteproc/imx_rproc.c
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Sync DTS with the mainline Linux and introduce fec node and
regulator configuration for rn5t567 PMU.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Sync DTS with the mainline Linux and introduce fec node.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Sync DTS with the mainline Linux and introduce fec node.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The Embedded Artists COM board is based on NXP i.MX7ULP.
It has a BD70528 PMIC from Rohm with discrete DCDC powering option and
improved current observability (compared to the existing NXP i.MX7ULP EVK).
Add the initial support for the board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Note: gpio7_8 was never used for usb power regulator so we remove it here
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Sync the Linux Kernel 5.4-rc6 device tree for Phytec Phycore
SoM and Segin board based on imx6UL and imx6ULL.
Changes includes Phytec naming convention for the devicetree files.
Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
This patch fixes the issue with broken bootaux command,
when M4 binary is loaded and data cache isn't flushed
before M4 core is enabled.
Reproducing:
> tftpboot ${loadaddr} ${board_name}/hello_world.bin
> cp.b ${loadaddr} 0x7F8000 $filesize
> bootaux 0x7F8000
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
1. Change information printed about loaded M4 binary, print the stack
pointer and reset vector addressed.
2. Add sanity check for the address provided as param.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch adds support for iMX6SX MMDC into the DDR calibration
code. The only difference between MX6DQ and MX6SX is that the SX
has 2 SDQS registers, while the DQ has 8.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
Instead of explicitly setting up each SDQS register, use a loop.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
Pull out the code turning SDQS pullups on and off into a separate
function, since it is replicated in two places in the code and it
is the single place in the entire function which is SoC dependent.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
The %08X format returns just zeroes with tiny printf, which is
horribly confusing, especially when debugging DRAM calibration
problems. Change the format to %08x (with lowercase x), which
behaves correctly with either implementation of printf in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
The wdt-reboot node is needed for the sysreset_watchdog driver to
register a watchdog as a reset handler in case 'CONFIG_SYSRESET' is
enabled.
Signed-off-by: Claudius Heine <ch@denx.de>
These DT files are copied from kernel v5.3 with no changes.
This is part 2 of 2 commits. Included are DT files for SOM rev 1.5, and
Hummingboard2 Gate/Edge.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
These DT files are copied from kernel v5.3 with no changes.
This is part 1 of 2 commits. Included are DT files for the original
Cubox-i and Hummingboard Base/Pro.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Copy device trees from linux, keeping them as separate files for
each board to ease future sync.
Update board code to use generic bx50v3 dt initially, then select
the specific dt based on board detection.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
This patch introduces support for i.MX28 based XEA board.
This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb) by using OF_PLATDATA.
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.
U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error
U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM: 128 MiB
MMC: MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet@800f0000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
add DM_SERIAL support for the aristainetos board, and
remove not used code from board code.
remove CONSOLE_OVERWRITE_ROUTINE.
Signed-off-by: Heiko Schocher <hs@denx.de>
as we switch to support DM and DTS, rework the existing
DTS trees. Change also Linux specific Device trees, goal
is to push this changes to linux.
Collect U-Boot specific changes in separate "*u-boot*" dts
files.
Signed-off-by: Heiko Schocher <hs@denx.de>
Add device trees from Linux in preparation for driver model
conversions.
device tree files taken from Linux:
71ae5fc87c34: "Merge tag 'linux-kselftest-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest"
and added SPDX license identifier.
Signed-off-by: Heiko Schocher <hs@denx.de>
remove 2b version of aristainetos board, as it
is easier to make the DM / DTS port and introduce
the 2b board version again (also some more board
version).
Signed-off-by: Heiko Schocher <hs@denx.de>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
On K3 devices there are 2 conditions where R5F can deadlock:
1.When software is performing series of store operations to
cacheable write back/write allocate memory region and later
on software execute barrier operation (DSB or DMB). R5F may
hang at the barrier instruction.
2.When software is performing a mix of load and store operations
within a tight loop and store operations are all writing to
cacheable write back/write allocates memory regions, R5F may
hang at one of the load instruction.
To avoid the above two conditions disable linefill optimization
inside Cortex R5F which will make R5F to only issue up to 2 cache
line fills at any point of time.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the ddr settings to use the DDR reg config tool rev 0.2.0.
This reduces the aging count(in DDRSS_CTL_274_DATA reg) to 15 in-order
to avoid DSS underflow errors.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
- Fix latest mainline kernel for rk3308
- Update rk3288-evb config to suport OP-TEE
- Fix for firefly-px30 DEBUG_UART channel and make it standalone
- Script make_fit_atf add python3 support
- Fix rk3328 timer with correct COUNTER_FREQUENCY
- Fix rk3328 ATF support with enable spl-fifo-mode
move the PCIE related config from arch Kconfig to PCI Kconfig.
As the PCI_LAYERSCAPE driver is being used in platform other than
fsl-layerscape platforms like ls102xa.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This fixes commit <91435cd40d30> "ARM: i.MX6: exclude the ARM errata
from i.MX6 UP system"
for nitrogen6x. The above commit removed the errata for the board
since MX6Q/MXDL/MX6S is selected via CONFIG_SYS_EXTRA_OPTIONS
This restores the errata configs.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
IMX based platforms can have the DCD table located on different
addresses due to differences in their memory maps (ie iMX7ULP).
This information is required by the user to sign the images for secure
boot so continue making it accessible via mkimage.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
SPL_ROCKCHIP_COMMON_BOARD, an almost identical option, has a title but
this one doesn't for some reason. Add a description to make the menu
easier to read.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Firefly Core-PX30-JD4 use UART2M1 while PX30 evb using UART2M0, the U-Boot
proper will use the dts setting to do the IOMUX init, and a separate dts
is needed for px30-firefly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
On a distribution with no python2 installed and no
python->python3 symlink the script will fail to execute.
Specify python3 explicitly as it's already a requirement
to build u-boot.
Signed-off-by: Jack Mitchell <ml@embed.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Instead of hardcode the base address, we can get them from the build
output, eg. get the SYS_TEXT_BASE from .config and get optee base from
DRAM_BASE.
We can use this script for SoCs with DRAM base not from 0x60000000(rk3229
and many other 32bit Rockchip SoCs), eg. rk3288 DRAM base is 0.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable AHB support for Flexspi controller interface meaning
memory can be accessed via md command using absolute addresses
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hardware comes out of reset with implicit values, but these are outside
the accepted range for Layerscape gen 3 chassis spec used on LS1028A.
Allocate different IDs and fix up Linux DT to use them.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2160A PL011 UART driver fetch IP block values using
platform data from board file instead of device tree.
Modified UART nodes in device tree to disable state.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
USB3.0 Receiver needs to enable fixed equalization
for each of PHY instances in an SOC. This is similar
to erratum A-009007, but this one is for LX2160A,
and the register value is different.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Mark board_fit_config_name_match() as weak so a board can overwrite the
empty function.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
struct sunxi_prcm_reg is naturally packed. There is no need to define it as
packed. Defining it as packed leads to compilation errors with GCC 9.2.1:
CC arch/arm/lib/reloc_arm_efi.o
arch/arm/cpu/armv7/sunxi/psci.c: In function ‘sunxi_cpu_set_power’:
:qarch/arm/cpu/armv7/sunxi/psci.c:163:21: error: taking address of packed
member of ‘struct sunxi_prcm_reg’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
163 | sunxi_power_switch(&prcm->cpu_pwr_clamp[cpu], &prcm->cpu_pwroff,
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Remove __packed attribute from struct sunxi_prcm_reg.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Orangepi Zero Plus 2 is an open-source single-board computer, available
in two Allwinner SOC variants, H3 and H5. We add support for H3 variant
here, as the H5 is already supported.
H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply
Sync dts from linux v5.2 commit:
"ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry"
(sha1: 75f9a058838be9880afd75c4cb14e1bf4fe34a0b)
Commit:
"ARM: dts: sun8i: h3: Refactor the pinctrl node names"
(sha1: a4dc791974e568a15f7f37131729b1a6912f4811)
has been avoided as it breaks U-Boot build.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Compiling with GCC 9.2.1 leads to build errors:
arch/arm/cpu/armv7/sunxi/psci.c: In function ‘sunxi_cpu_set_power’:
arch/arm/cpu/armv7/sunxi/psci.c:144:21: error: taking address of packed
member of ‘struct sunxi_cpucfg_reg’ may result in an unaligned pointer
value [-Werror=address-of-packed-member]
144 | sunxi_power_switch(&cpucfg->cpu1_pwr_clamp, &cpucfg->cpu1_pwroff,
| ^~~~~~~~~~~~~~~~~~~~~~~
arch/arm/cpu/armv7/sunxi/psci.c:144:46: error: taking address of packed
member of ‘struct sunxi_cpucfg_reg’ may result in an unaligned pointer
value [-Werror=address-of-packed-member]
144 | sunxi_power_switch(&cpucfg->cpu1_pwr_clamp, &cpucfg->cpu1_pwroff,
| ^~~~~~~~~~~~~~~~~~~~
Use memcpy() and void* pointers to resolve the problem caused by packing
the struct sunxi_cpucfg_reg.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
This patch is only a temporarily workaround for crash introduced by
commit ac9cd4805c ("bootstage: Correct relocation algorithm").
The crash occurs because the bootstage struct is not correctly aligned
when BOOTSTAGE feature is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate by default the command CLS (clear screen);
this command used in pxe or sysboot command (DISTRO support)
when the "menu background" keyword is present.
This patch avoid the warning "Unknown command 'cls'"
with extlinux.conf:
# Generic Distro Configuration file generated by OpenEmbedded
menu title Select the boot mode
MENU BACKGROUND /splash.bmp
TIMEOUT 20
DEFAULT stm32mp157c-ev1-emmc
LABEL stm32mp157c-ev1-emmc
KERNEL /uImage
FDT /stm32mp157c-ev1.dtb
APPEND root=/dev/mmcblk1p4 rootwait rw console=ttySTM0,115200
...
Retrieving file: /mmc0_stm32mp157c-ev1_extlinux/extlinux.conf
614 bytes read in 36 ms (16.6 KiB/s)
Retrieving file: /splash.bmp
46180 bytes read in 40 ms (1.1 MiB/s)
Unknown command 'cls' - try 'help'
Select the boot mode
1: stm32mp157c-ev1-sdcard
...
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
The SST26VF064BEUI spi-nor flash is programmed at the factory with a
globally unique address stored in the SFDP vendor parameter table and
it is permanently writeprotected. Retrieve the EUI-48 address and set it
as ethaddr env.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
commit 3b3e8a37d3
("arm: dts: am335x: sync cpsw/mdio/phy with latest linux - drop phy_id")
did sync with recent linux kernel and replaced therefore the 'phy_id'
property with a phy-handle pointing to the mdio.
This is OK for linux, but introduces trouble with the already running
vxWorks on this target.
So this commit here re-inerts the phy_id property beside the phy-handle
property to be compatible with both.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
The commit 1b42ab3eda ("ARM: DRA7: Fixup DSPEVE, IVA and GPU clock
frequencies based on OPP") added the core logic to update the kernel
device-tree blob to adjust the DSP, IVA and GPU DPLL clocks based on
a one-time OPP choice selected in U-Boot for most of the DRA7xx/AM57xx
family of SoCs.
The DSPs on DRA76xP/DRA77xP SoCs (DRA76x ACD package SoCs) though
provide a higher performance and can run at a higher clock frequency
of 850 MHz at OPP_HIGH instead of 750 MHz. Fix up the logic to use the
correct clock rates on these SoCs. Note that this higher clock rate is
not applicable to other Jacinto 6 Plus SoCs (DRA75xP/DRA74xP SoCs or
AM574x SoCs) that follow the ABZ package.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add DT nodes related to DMA and CPSW to -u-boot.dtsi to get networking
up on J721e EVM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Based on upstream-linux
See https://github.com/torvalds/linux/commit/f66b2aff.
However made the XSMI register window 0x16 (22) bytes per my reading
of the functional spec. Similar commits in Marvels own repo bump it
to 0x200 (512) bytes but I did not see the reasoning for that.
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/4d932b4.
Also added device-name attributes to prevent ambiguity in the `mdio`
command.
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The AM654 SoC doesn't allow to disabling RGMII TX internal delay in CPSW2G
MAC. Hence, change CPSW2G interface mode to "rgmii-rxid" - RGMII with
internal RX delay provided by the PHY, the MAC will add an TX delay in this
case.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Part of the env cleanup moved this out of the environment code and into
the net code. However, this helper is sometimes needed even when the net
stack isn't included.
Move the helper to lib/net_utils.c like it's similarly-purposed
string_to_ip(). Also rename the moved function to similar naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Ondrej Jirman <megous@megous.com>
In GCC 9 support for the Armv5 and Armv5E architectures (which have no
known implementations) has been removed, cf.
https://gcc.gnu.org/gcc-9/changes.html
Commit 16540d07fd ("arm: fix -march for ARM11") changed the value of the
compiler flag from -march=armv5 and -march=armv5t into -march=armv6 for
ARM11.
The values prior to this patch were:
arch-$(CONFIG_CPU_ARM1136) =-march=armv5
arch-$(CONFIG_CPU_ARM1176) =-march=armv5t
The change lead to a regression with the Raspberry Pi Zero W not booting
anymore.
Use -march=armv5t both for ARM1136 and ARM1176.
Fixes: 16540d07fd ("arm: fix -march for ARM11")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Joris Offouga <offougajoris@gmail.com>
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
-----BEGIN PGP SIGNATURE-----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=L2zo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191209' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.01
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
Recently the version check was improved to be able to determine that
we're running on SoC revision 2.1. A check for B0 was tightened so
that it now must equal 0x20 instead of being bigger than 0x20. On
some B0 chips the value returned is 0x1020 instead of 0x20. This
means even though it's B0, the check will fail and code relying on
the correct chip revision will make wrong decisions. There is no
documentation of those bits, but it seems that NXP always uses a
byte to encode the revision. Thus remove the upper bits to fix the
regression.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
- rockchip pwm driver update to support all the SoCs
- RK3308 GMAC and pinctrl support
- More UART interface support on PX30 and pmugrf reg fix
- Fixup on misc for eth_addr/serial#
- Other updates on variant SoCs
Ever since the conversion to DM PCI, the board was missing the PCIe DT
nodes, hence the PCI did not really work. Fill in the DT nodes and add
missing PCIe device reset.
Moreover, bring the PCIe power domain up before booting Linux. This is
mandatory to keep old broken vendor kernels working, as they do not do
so and depend on the bootloader to bring the power domain up.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
In preparation for use of DDR DRAM fine-tuning upon boot,
convert the board to SPL framework instead of using DCD
tables to bring up DRAM and pinmux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Make the PMU LDO configuration interface available to board code,
so that board code can reconfigure the internal LDOs of the SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
i.MX 7's Cortex-M4 core can run from DDR and uses DDR memory for
the rpmsg communication. Both use cases need a fixed location of
memory reserved. For the rpmsg use case the reserved area needs
to be in sync with the kernel's hardcoded vring descriptor location.
Use the linux,usable-memory property to carve out 1MB of memory
in case the M4 core is running. Also make sure that the i.MX 7
specific rpmsg driver does not get loaded in case we do not carve
out memory.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The NoC registers on i.MX6QP needs to be configured, otherwise some
usecases in the kernel behave incorrectly, such as rotation and resize.
Currently the NoC registers are not configured in the kernel, so
configure them in U-Boot like it is done in the NXP U-Boot tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Sync the mx7ulp device tree related files with the one from
NXP U-Boot vendor tree (imx_v2019.04_4.19.35_1.0.0).
The mainline support for i.MX7ULP is very premature at this stage.
We should probably re-sync with mainline Linux dts when it gets
in better shape, but for now sync with the U-Boot vendor code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The LDOVL definitions is common to all the modes, not only RUN mode,
so in order to avoid confusion, remove the _RUN notation from the PMC1
LDOVL definitions.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Introduce the CONFIG_LDO_ENABLED_MODE option so that i.MX7ULP boards
designed to operate with LDO enabled mode can work with 0.95V at LDO
output in RUN mode as per the datasheet.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
As per the i.MX7ULP datasheet, it can boot in LDO enabled mode
or LDO bypass mode.
Print the LDO mode status in the U-Boot log for convenience.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
When we want to use plus pinctrl feature, we need to enable
them at spl.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This PWM driver can be used to support pwm functions
for on all Rockchip Socs.
The previous chips than RK3288 did not support polarity,
and register layout was different from the RK3288 PWM.
The RK3288 keep the current functions.
RK3328 and the chips after it, which can support hardware lock,
configure duty, period and polarity at next same period, to
prevent the intermediate temporary state.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Firefly ROC_RK3308_CC use ref_clock of input mode,
and rmii pins of m1 group.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3308 only support RMII mode, and if it is output clock
mode, better to use ref_clk pin with drive strength 12ma.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
serial# is one of the vendor properties and thus protected from being
overwritten if already set. If env_set is called anyway this result in
some nasty warnings, so check for presence before trying that.
In the same direction check for the presence of cpuid# and compare it
to the actual hardware and emit a warning if they don't match.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip_setup_macaddr() runs from an initcall, so returning an error
code will make that initcall fail thus breaking the boot process.
And if an ethernet address is already set this is definitly not a
cause for that, so just return success in that case.
Fixes: 0482538499 ("rockchip: rk3399: derive ethaddr from cpuid");
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some generic PX30 SoMs found in the wild use UART3 as their debug output
instead of UART2 (used for MMC) and UART5.
Make it possible to use UART3 as early debug output, with the associated
clock and pinmux configuration. Two sets of output pins are supported (M0/M1).
Future users should also note that the pinmux default in the dts is to use
the M1 pins while the Kconfig option takes M0 as a default.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
UART3 also has two sets of pins that can be selected.
Rename the config option to a common name, to allow it to be used for both
UART2 and UART3.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
According to the PX30 TRM, the iomux registers come first, before the pull
and strength control registers.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.
And show my best respect to Heiko's work for this solution.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
This adds a general board file based on MT8518 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8518 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
[trini: Migrate env location to defconfig, set ENV_IS_IN_MMC]
Signeed-off-by: Tom Rini <trini@konsulko.com>
Add support for MediaTek MT8518 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
We don't have full device-tree support in SPL yet - add an appropriate
U_BOOT_DEVICE() to the board file.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The DM family of DaVinci SoCs is no longer supported. Drop the
irrelevant code from the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This commit:
d409c96216
causes build failure with ICACHE enabled. This is due to missing
invalidate_icache_all() stub. Let's add empty invalidate_icache_all() in
the case where ICACHE is not enabled.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these functions into the command.h header file which is a better fit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are fairly widely used in
U-Boot. But it is not clear that they will use driver model anytime soon,
so we don't want to label them as 'legacy'.
Move them to a new irq_func.h header file. Avoid the name 'irq.h' since it
is widely used in U-Boot already.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h since they do not use driver model.
Move them over. Don't bother adding comments since these functions should
be deleted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function has a similar name to the common wait_ticks(). It is only
used in one place and seems small enough to drop.
Inline it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in time.h so move them over and add comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.
Use the vsprintf.h include file explicitly where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These should be moved to driver model, but in the meantime, move them
out of the common header to help reduce its size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Although layerscape platforms reuse mxc_get_clock() of i.MX platforms,
eSDHC clock getting do not have to use it. It uses global data
gd->arch.sdhc_clk directly in fsl_esdhc driver. Even there are more
than one eSDHC controllers on SoC, they use same reference clock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update the sdmmc2 node for eMMC support on eval board stm32mp157c-ev1.
- update slew-rate for pin configuration
- update "vqmmc-supply"
- remove "st,sig-dir"
- add mandatory "pinctrl-names"
- add "mmc-ddr-3_3v"
This patch solve the eMMC detection issue for command "mmc dev 1".
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Device tree and binding alignment with kernel v5.4-rc4
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Device tree and binding alignment with kernel v5.3
and converted to SPDX.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
-----BEGIN PGP SIGNATURE-----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=4Z+A
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.01' of https://github.com/mbgg/u-boot
- add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
In case the SPL on Gen5 loads U-Boot from NAND, unreset the NAND IP
explicitly in the platform code as the denali-spl driver is not aware
of DM at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add new FPGA ID for ArriaV ST/D3 or SX/B3 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
On Gen5, when the FPGA is loaded and there was some prior interaction
between the HPS and the FPGA via bridges (e.g. Linux was running and
using some of the IPs in the FPGA) followed by warm reset, it has been
observed that there might be outstanding unfinished transactions. This
leads to an obscure misbehavior of the bridge.
When the bridge is enabled again in U-Boot and there are outstanding
transactions, a read from within the bridge address range would return
a result of the previous read instead. Example:
=> bridge enable ; md 0xff200000 1
ff200000: 1234abcd
=> bridge enable ; md 0xff200010 1
ff200010: 5678dcba <------- this is in fact a value which is stored in
a memory at 0xff200000
=> bridge enable ; md 0xff200000 1
ff200000: 90effe09 <------- this is in fact a value which is stored in
a memory at 0xff200010
and so it continues. Issuing a write does lock the system up completely.
This patch opens the FPGA bridges in 'bridge enable' command, the tears
them down again, and then opens them again. This allows these outstanding
transactions to complete and makes this misbehavior go away.
However, it is not entirely clear whether this is the correct solution.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
On Gen5, the 'bridge disable' command write 0x0 to brgmodrst register,
which releases all bridges from reset, instead of putting all bridges
into reset. Fix this by inverting the mask and actually putting the
bridges into reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Provide a defconfig which allows us to boot Raspberrry Pi 4
and Raspberry Pi 3 Model B/B+
Instead of using the embedded DTB as done in RPi3 we use the
devicetree provided by the firmware.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
For bcm283x based on arm64 we also have to change the mm_region.
Add assign this in mach_cpu_init() so we can create now one binary
for RPi3 and RPi4.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
As part of the effort to create one binary for several bcm83x SoCs
we read the IO base address from device-tree.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
We move the per SOC define BCM283x_BASE to a global variable.
This is a first step to provide a single binary for several bcm283x
SoCs.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Rename the file bcm283x-uboot.dtsi so that it get
automatically include through the scripts/Makefile.lib
using $(CONFIG_SYS_SOC))-u-boot.dtsi
Without this uarts and pincontroller miss the property dm-pre-reloc
and the first call to bcm283x_mu_serial_ofdata_to_platdata() fails
as the pins are not set correctly.
As a result the U-Boot banner isn't shown on boot.
Before commmit
143256b353 ("fdt: update bcm283x device tree sources to Linux 5.1-rc6 state")
we included bcm283x-uboot.dtsi directly in the device-tree file.
Which got deleted by the metioned commit.
This is a much robuster solution.
Reported-by: Tom Rini <trini@konsulko.com>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Tom Rini <trini@konsulko.com> [RPi 3, 32b and 64b modes]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
In commmit
143256b353 ("fdt: update bcm283x device tree sources to Linux 5.1-rc6 state")
we deleted the label for the node soc from bcm283x.dtsi
As we don't need to add the property dm-pre-reloc to the soc node,
we can delete it from bcm283x-uboot.dtsi
Tested-by: Tom Rini <trini@konsulko.com> [RPi 3, 32b and 64b modes]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
In GCC 9 support for the Armv5 and Armv5E architectures (which have no
known implementations) has been removed, cf.
https://gcc.gnu.org/gcc-9/changes.html
ARM11 is an armv6 implementation. So change the architecture flag for the
compiler to armv6 for ARM11.
Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
As part of loading trustedfirmware, the SPL is required to place portions
of code into the socs sram but the mmc controllers can only do dma
transfers into the regular memory, not sram.
The results of this are not directly visible in u-boot itself, but
manifest as security-relate cpu aborts during boot of for example Linux.
There were a number of attempts to solve this elegantly but so far
discussion is still ongoing, so to make the board at least boot correctly
put both mmc controllers into fifo-mode, which also circumvents the
issue for now.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Setup dwc3_device structure for non-dm gadgets, which is used
in rk3399 platforms.
dwc3_device would have basic regbase, dr_mode, high speed
and 16-bit UTMI+ etc.
Cc: Marek Vasut <marex@denx.de>
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Fix to use CONFIG_USB_DWC3_GADGET instead of CONFIG_USB_DWC3)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use generator script so that we can use environment for TEE source.
$TEE for tee.bin, and if file not exist, the script can report a warning,
and meke the build success without a error.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add 'ethernet0' as alias for 'gmac0' in S10 device tree.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
The HPS EMAC0 drive strength is changed to 4mA because the initial 8mA
drive strength has caused CE test to fail. This requires changes on the
pad skew for EMAC0 PHY driver. Based on several measurements done, Tx
clock does not require the extra 0.96ns delay which was needed in
Arria10.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The file arch/arm/mach-socfpga/include/mach/misc.h used the same include
guard as the global include/misc.h.
Fix this by giving the arch file an arch prefix.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add #address-cells and #size-cells to memory node to fix incorrect memory
size decoding in recent Uboot version.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
The UEFI spec mandates that unaligned memory access should be enabled if
supported by the CPU architecture.
This patch implements the function unaligned_access() to set the enable
unaligned data support flag and to clear the aligned flag in the system
control register (SCTLR). It is called when UEFI related commands like
bootefi are invoked.
Reported-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Tested-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Tested-by: Guillaume Gardet <Guillaume.Gardet@arm.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- remove "synopsys,dw-mipi-dsi" compatible to reduce the device tree
differences between Linux and U-Boot for stm32mp1 platform
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXdJyOg4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXOmuAJ9lF7GyPpv0vZNX1V4UV2EyyOOdbwCfQzHu3Xo+
3VWLV9ZHkVMlfnGbbx0=
=+YuG
-----END PGP SIGNATURE-----
Merge tag 'video-for-v2020.01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix i.MX6ULL evk black screen observed while reboot stress tests
- remove "synopsys,dw-mipi-dsi" compatible to reduce the device tree
differences between Linux and U-Boot for stm32mp1 platform
- Add support for rockchip SoC: PX30, RK3308
- Add and migrate to use common dram driver: PX30, RK3328, RK3399
- Add rk3399 board Tinker-s support
- Board config update for Rock960, Rockpro64
Support tinker-s board. The board is equivalent of tinker board
except of emmc.
TODO:
- support of usb current burst when the board is powered from pc
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
dmc is used to initialize the memory controller. It's needed by
u-boot. Move it in the specific section
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We shouldn't force which allocator the SPL uses, since there's no
platform requirement for one over the other: in fact, we currently allow
selection of the TPL allocator but not the SPL one!
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The common SPL removed SoC-specific code for RK3399's SPL and in the
process caused the previously-unconditional DRAM initialization in
board_init_f() to only happen when compiling a configuration that does not
support TPL, meaning DRAM never gets initialized if TPL is supported but
disabled.
Fix this by omitting the DRAM init in SPL only when we are configured to
also build a TPL. This fixes custom configurations that have disabled
TPL, and it should also unbreak the "ficus-rk3399", "rock960-rk3399",
and "chromebook_bob" defconfigs, although since I don't have any of
those devices I can't confirm they're broken now.
Fixes: b7abef2ecb ("rockchip: rk3399: Migrate to use common spl board file")
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The common SPL code reordered the DRAM initialization before
rockchip_stimer_init(), which as far as I can tell causes the RK3399 to
lock up completely.
Fix this issue in the common code by putting the DRAM init back after
timer init. I have only tested this on the RK3399, but it wouldn't make
any sense for the timer init to require DRAM be set up on any system.
Fixes: b7abef2ecb ("rockchip: rk3399: Migrate to use common spl board file")
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ROC-RK3308-CC is a rk3308 based board designed by
Firelfy, with eMMC and 256MB DDR3 and RTL8188 Wifi
on board.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dts file for ROC-RK3308-CC from firefly.
Sync form linux rockchip for v5.5-armsoc/dts64:
"arm64: dts: rockchip: Add devicetree for board roc-rk3308-cc"
(sha1: 4403e1237be3af0977aa23ef399e3496316317a0)
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dts for rk3308 evb, sync from the linux kernel
upstream list [0].
[0]https://patchwork.kernel.org/patch/11201555/
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3308 is a quad Cortex A35 based SOC with rich audio
interfaces(I2S/PCM/TDM/PDM/SPDIF/VAD/HDMI ARC), which
designed for intelligent voice interaction and audio
input/output processing.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Common PLL setup function, compatible with different SOC.
Mainly for the subsequent new SOC use.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We should set the init value when vdd_log is enabled, or else the
vdd_log output voltage may not in soc required range.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We should set the init value when vdd_log is enabled, or else the
vdd_log output voltage may not in soc required range.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We should set the init value when vdd_log is enabled, or else the
vdd_log output voltage may not in soc required range.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add vdd_log node according to rock960 schematic V13.
This patch affect two boards:
- Rock960 Model A
- Ficus
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The u-boot specific device tree directives should be in u-boot.dtsi
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The u-boot specific device tree directives should be in u-boot.dtsi
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The u-boot specific pieces in the dts files should be in u-boot.dtsi
not the main files, this allows easier sync with upstream. The
rk3399.dtsi has a mix of both so move them all for consistency.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Fix with missing pmugrf)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rockpro64 needs to setup I/O domains in order for USB to work in u-boot.
Since we currently don't have a driver to do that, split it into its own
board file and initialize I/O domains here.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip_reset_bind() already does the needed init for the reset
registers, only referenced the wrong cru structure.
So we can get rid of the open-coded reset init and just fix
the correct cru reference.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3399 VD_CENTER voltage domain is not subject to dynamic voltage
scaling. So the regulator reset voltage of 0.9V is used on this board.
Let u-boot initialize the center voltage to 0.95V as it is done for the
VD_LOGIC domain. This avoids instability and occasional linux kernel
Opses on this board.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The most important change for u-boot is the fix for the vdd-log pwm
voltage regulator to avoid overvoltage for the VD_LOGIC power domain.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Few important regulator power rails fixes are available in
linux-next, so sync them same.
Here is the last commit details:
commit <9f7f9b610e1b7d2dc86c543ab0dfcf781bd42326> ("arm64: dts:
rockchip: Fix roc-rk3399-pc regulator input rails")
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add core architecture code to support the px30 soc.
This includes a separate tpl board file due to very limited
sram size as well as a non-dm sdram driver, as this also has
to fit into the tiny sram.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add px30 related devicetrees synced from the Linux kernel.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Newer Rockchip socs use a different ip block to handle one-time-
programmable memory, so depending on what got enabled get the cpuid
from either source.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The px30 contains 2 separate clock controllers, pmucru and cru.
Add drivers for them.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add headers needed by the upcoming px30 support, including two
new dt-binding headers taken from the Linux kernel.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Right now enabling SPL_FRAMEWORK will also enable it for the TPL in all
cases, making the TPL bigger. There may be cases where the TPL is really
size constrained due to its underlying ram size.
Therefore introduce a new TPL_FRAMEWORK option and make the relevant
conditionals check for both. The default is set to "y if SPL_FRAMEWORK"
to mimic the previous behaviour where the TPL would always get the
SPL framework if it was enabled in SPL.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update the calculation of the stride to support all the DRAM case.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
For there are some structures and functions are common for all rockchip SoCs,
migrate to use the common code so that we can clean up reduandent codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
RK3328 has a similar controller and phy with PX30, so we can use the
common driver for it and remove the duplicate codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add the sdram driver for PX30 to support ddr3, ddr4, lpddr2 and lpddr3.
For TPL_BUILD, the driver implement full dram init and without DM
support due to the limit of internal SRAM size.
For SPL and U-Boot proper, it's a simple driver with dm for get
dram_info like other SoCs.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The noc register bit definition may be the same for different SoC while
the offset of the register may be different, add the struction
definition as common code.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This sdram_phy_px30.c is based on PX30 SoC, the functions are common
for phy, other SoCs with similar hardware could re-use it.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This sdram_pctl_px30.c is based on PX30 SoC, the functions are common
for controller, other SoCs with similar hardware could re-use it.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
There are some function like os_reg setting, capacity detect functions,
can be used as common code for different Rockchip SoCs, add a
sdram_common.c for all these functions.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We are using sys_reg2 and sys_reg3 as ddr cap info, sync the variable
name to what we real use to avoid confuse people.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Since we have new DRAM type and to support different DRAM size in different
CS, we need more bits, so introduce sys_reg3 to record the info.
Note that the info in sys_reg3 is extension to sys_reg2 and the info in
sys_reg2 is the same as before. We define the DRAM_INFO with sys_reg3 as
VERSION2.
All the ENC macro are moved to sdram_common.h since the sdram.c only
need to do the info decode.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The sdram.h suppose to be helper file for sdram.c which including dram
size decode and some u-boot related dram init interface, and all
structure and function for dram driver move to sdram_common.h
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rename sdram_common.c in arch/arm/mach-rockchip to sdram.c;
so that we can use the file name sdram_common.c in dram driver for
better understand the code;
clean the related file who has use the header file at the same time.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The header file sdram.h is used for rk3288 and similar SoCs, rename it
to make it more understandable.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
According to discussion in the Linux PCI list [1], the dma-ranges should
be continuous and describe the entire inbound window which the controller
can address and not take into account the possible DRAM holes.
Temporarily disable this code which updates the dma-ranges until this
meaning is sorted out.
[1] PCI: rcar: Do not abort on too many inbound dma-ranges
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable gpio0 in SPL to allow the sdhci driver read the SD card-detect
signal.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
As mentioned in doc/README.arm-relocation gd->bd is not available in
dram_init() so we shouldn't attempt to access it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Remove the compatible "synopsys,dw-mipi-dsi" added in U-Boot
(it don't exist in Linux kernel binding); it is only used
to bind the generic synopsys UCLASS_DSI_HOST "dw_mipi_dsi" to
the driver "stm32-display-dsi" UCLASS_VIDEO_BRIDGE
This binding is done in Linux kernel drivers without compatible
(dw_mipi_dsi_bind() is called in bind of driver, for example in
drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c).
This patch does the same in U-Boot driver, the STM32 driver
calls during its bind the function device_bind_driver_to_node
to bind the generic driver "dw_mipi_dsi" at the same address.
This patch reduces the device tree differences
between Linux kernel and U-Boot for stm32mp1 platform.
Tested with v2020.01-rc1 on STM32MP157C-EV1 and STM32MP157C-DK2.
The dependency of driver is clearer and the probe order is guaranteed.
STM32MP> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
sysreset 0 [ ] syscon_reboot |-- reboot
simple_bus 0 [ + ] generic_simple_bus |-- soc
serial 0 [ + ] serial_stm32 | |-- serial@40010000
...
video_brid 0 [ + ] stm32-display-dsi | |-- dsi@5a000000
dsi_host 0 [ + ] dw_mipi_dsi | | |-- dsihost
panel 0 [ + ] rm68200_panel | | `-- panel-dsi@0
...
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
-----BEGIN PGP SIGNATURE-----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=sgCz
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191105
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
This patch enable TPL support for firefly-rk3288 board, which works ths
same way with other RK3288 board like Tinker, evb.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Without the prefix, "same-as-spl" in `u-boot,spl-boot-order` will not work
as expected. When board_boot_order() `spl-boot-order.c` meets
"same-as-spl", it gets the conf by looking the boot_devices table by boot
source, and parse the node by the conf with:
node = fdt_path_offset(blob, conf);
which will failed without the "/" indicating the path.
Currently only entries of boot_devices in rk3399 have the "/" prefix.
Therefore add the missing ones in other boards.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use the same SPL_STACK_R_ADDR in Kconfig instead of each board config;
default to 0x4000000(64MB) instead of 0x80000(512KB) for this address
can support all the SoCs including those may have only 64MB memory, and
also reserve enough space for atf, kernel(in falcon mode) loading.
After the ATF entry move to 0x40000, the stack from 0x80000 may be override
when loading ATF bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
A trusted execution environment should also get loaded as loadable from
a fit image, so add the possibility to present a tee.elf to make_fit_atf.py
that then gets included as additional loadable into the generated its.
For ease of integration the additional loadable is created as atf_(x+1)
after all others to re-use core generation loops.
Tested against the combinations of 1-part-atf and multi-part-atf each
time with and without a tee binary present.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3328 can use same-as-spl option so next loaders are loaded from the same
medium.
Add the boot order in the rock64 dts otherwise booting from sdcard
will result in u-boot looking into the eMMC.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a call to rk3328_configure_cpu() during initialization to set the
CPU-clock frequency.
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Specification
- Rockchip RK3399
- LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply
Commit details of rk3399-leez-p710.dts sync from linus tree for Linux 5.4-rc1:
"arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC"
(sha1: fc702ed49a8668a17343811ee28214d845bfc5e6)
Signed-off-by: Andy Yan <andyshrk@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
While getting the 'subarg' of 'hwconfig' env variable in
config_core_prefetch(), if no hwconfig variable is defined,
below warning is received:
WARNING: Calling __hwconfig without a buffer and
before environment is ready
Fix this by checking 'hwconfig' env variable.
If not found return without further processing.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
The fsl-layerscape already occupies board_late_init(), therefore it is
not possible for a board to have its own board_late_init(). Introduce
fsl_board_late_init() which can be implemented in the board specific
code.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The clocks are not dependent on the target but only on the SoC.
Therefore, convert the CONFIG_TARGET_x macros to the corresponding
CONFIG_ARCH_x. This will allow other targets to automatically use the
common code. Otherwise every new target would have to add itself to the
"#if defined(CONFIG_TARGET_x) || .." macros.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Erratum A-050382 states that the eDMA ICID programmed in the eDMA_AMQR
register in DCFG is not correctly forwarded to the SMMU.
The workaround consists in programming the eDMA ICID in the eDMA_AMQR
register in DCFG to 40.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If SEC FW support is not enabled (ARMV8_SEC_FIRMWARE_SUPPORT=n), below
compilation error appears
arch/arm/include/asm/arch-fsl-layerscape/fsl_icid.h:169:4: error:
'CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT' undeclared here (not in a function)
Fix it by wrapping with CONFIG_IS_ENABLED().
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
These macros should only be used when CONFIG_FSL_CAAM is present.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If the secure world reset handlers are used (via CONFIG_PSCI_RESET),
then do not use the layerscape-specific implementation.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This allows the use of PSCI calls to trusted firmware to
initiate reset and poweroff events with CONFIG_PSCI_RESET and
CONFIG_ARM_PSCI_FW. This is desirable, for example, if the target
board has implemented a custom reset or poweroff procedure in EL3.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The only GPIO bank needed in SPL is GPIO4 and the SPL space is tight.
This patch removes the all but GPIO4 from the spl device tree to
reduce the SPL footprint.
Signed-off-by: Adam Ford <aford173@gmail.com>
The only GPIO bank needed in SPL is GPIO4 and the SPL space is tight.
This patch removes the all but GPIO4 from the spl device tree to
reduce the SPL footprint.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add VTM node for voltage and thermal management. For u-boot, this is needed
for supporting AVS class 0, as the efuse values for the OPPs are stored
under the VTM.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Link the vdd-supplies for the voltage domains under the VTM node. Also,
enable the node under SPL. This will enable the AVS class 0 support on
am65x-evm board.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
MPU voltage on AM65x-evm is controlled via the TPS62363 chip attached
to i2c0 bus. Add device node for this so that it can be controlled via
a regulator driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Add VTM node for voltage and thermal management. For u-boot, this is needed
for supporting AVS class 0, as the efuse values for the OPPs are stored
under the VTM.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
As part of disabling caches MMU as well gets disabled. But MMU is not
available on all armv7 cores like R5F. So disable MMU only if it is
available.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The default implementation of ERR_PTR/PTR_ERR maps errno values at the
and of the address range (e.g. -EINVAL/-22 gets 0xFFFFFFEA).
For socfpga gen5 SPL, this doesn't really work, as the heap is nearly
at the end of the 32 bit address range.
This patch adjusts the ERR_PTR_OFFSET to map errno values into the range
of the Boot ROM, which should not be used for valid pointers.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Provide optimized memcpy_{from,to}io() and memset_io(). This is required
when moving large amount of data to and from IO regions such as IP
registers or accessing memory mapped flashes.
Code is borrowed from Linux Kernel v5.4.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
When CONFIG_$(SPL_)CLK not defined, the clock controller device
not exist, so to avoid boot failure for platform not have
CONFIG_$(SPL_)CLK, add a check.
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MN support loading images with rom api, so we implement
reuse board_return_to_bootrom to let ROM loading images.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the BYPASS ID SWAP bit (GPR10 bit 1) in order for GPU not to
generated AXI bus errors with TZC380 enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MN has similar architecture with i.MX8MM, so it could reuse
the clock code of i.MX8MM, but i.MX8MN has different CCM root
configurations, so need a separate root entry.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
with u-boot,dm-spl added for imx8qm-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add subcommand for add writing BCB only, where we provide appropriate
offsets for firmware1 and firmware2 and size.
Example of usage:
> nandbcb bcbonly 0x00180000 0x00080000 0x00200000
Writing 1024 bytes to 0x0: randomizing
OK
Writing 1024 bytes to 0x20000: randomizing
OK
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Move code for writing FCB/DBBT pages to a separate function
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add support for updating FCB/DBBT on i.MX7:
- additional new fields in FCB structure
- Leverage hardware BCH/randomizer for writing FCB
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This commit adds support for the brppt2 board. The board is based on the
i.mx6 dual-lite SoC.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Borrow ID reading code from Ye Li (NXP U-Boot, commit ID 5b443e3e2617)
but drop imx-mkimage commit ID reading since we now use in tree mkimage.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Need to pass total 5 arguments for SIP HAB call on i.MX8MQ,
so update the interface to add new argument.
Signed-off-by: Ye Li <ye.li@nxp.com>
[agust: fixed imx8m-power-domain build]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add function and new command "auth_cntr" for secure boot support.
When booting with life cycle set to OEM closed, we need to use
this function to authenticate the OS container and load kernel & FDT
from OS container to their destination.
Also add image authentication call when loading container images.
Users can set CONFIG_AHAB_BOOT=y to enable the feature. It is not
set at default.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for
DRAM and linux suspend voltage requirement.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
It will be easy to separate SD/EMMC when booting in SPL stage, then
no need to bother which device is BOOT_DEVICE_MMC1/2.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add init_nand_clk to enable gpmi nand clock. Since i.MX8MQ not use CCF,
so we still use legacy mode to configure the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The i.MX8MQ B1 uses OCOTP_HW_OCOTP_READ_FUSE_DATA register for chip id.
It returns a magic number 0xff0055aa. update get_cpu_rev to support it,
and enable ocotp clock to access ocotp.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Migrate to DM_VIDEO, update the device tree and remove code that is no
longer necessary.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Migrate to DM_ETH and remove code that is no longer necessary.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
This updates the i.MX8MQ device trees and, necessarily, also the
i.MX8MQ clock bindings. These are taken verbatim from from the
Linux kernel version v5.4-rc2, which three small changes which
were already part of the previous device tree:
* Keep the PSCI reserved memory range
* Keep the alias for ethernet, so that the MAC address can be set
* Keep the modified #include for the IOMUXC pins
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Acked-by: Peng Fan <peng.fan@nxp.com>
This commit converts mccmon6's u-boot proper (in a single commit to avoid
build breaks) to use solely DM/DTS.
The DTS description of the mccmon6 has been ported from Linux kernel
(v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add u-boot,dm-pre-reloc properties for uart pinmux configuration
nodes, which enables UART as early as possible (before relocation).
Without this we miss almost the half of output (U-boot version,
CPU defails, Reset cause, DRAM details etc.).
Fixes: cd69e8ef9b ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm")
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to
keep original imx6ull-colibri.dts in sync with Linux.
Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi +
additionally fix checkpatch warnings.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
According to IMX28CEC rev. 4, 10/2018, Table 15. Recommended Operating
Conditions, page 16, the VDDD should be set to 1.55V when the CPU is
operating at 454MHz. This is the case in U-Boot, hence increase the
VDDD voltage. This fixes instability when performing TFTP transfers.
Increase the brownout threshold to 1.4V. The documentation recommends
1.45V setting for the brownout, however, this triggers failure during
power block init, so keep the brownout slightly lower.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
imx6_is_bmode_from_gpr9 always returns false, because
IMX6_SRC_GPR10_BMODE is 1<<28 and gets casted to u8 on return.
This moves the function body into imx6_src_get_boot_mode, since that is the
only one using it and it is on the same abstraction level (accessing
registers directly).
Signed-off-by: Claudius Heine <ch@denx.de>
Introduce disable_ipu_clock(). This is done in preparation for
configuring the NoC registers on i.MX6QP in SPL.
Afer the NoC registers are set the IPU clocks can be disabled.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The code can be made simpler by using setbits_le32(), so switch
to it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add get_timer_us(), which is useful e.g. when we need higher
precision timestamps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
[trini: Fixup arch/arm/mach-bcm283x/include/mach/timer.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
At present some boards generate kwbimage.cfg in the source tree
during the build. This breaks buildman testing on some systems
where the source tree is read-only. Update makefile rules to
generate it in the build tree instead.
Note some other boards have the kwbimage.cfg file written in
advance, hence we need check if the file exists in the build
tree first, otherwise we fall back to one in the source tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the address spaces for the R5F cores in MCU domain to the ranges
property of the cbass_mcu interconnect node so that the addresses
within the R5F nodes can be translated properly by the relevant OF
address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use the 3733MTs DDR configuration that is auto generated from
DDR_Regconfig tool.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
Added the following registers to the DDR configuration:
- ACIOCR0,
- ACIOCR3,
- V2H_CTL_REG,
- DX8SLxDQSCTL.
Modified enable_dqs_pd and disable_dqs_pd to only touch the associated
bit fields for pullup and pulldown registers (to preserve slew rate and
other bits in that same register). Also update the dts files in the same
patch to maintain git bisectability.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The current configuration of DDR on AM654 base board is for 1600MTs but
the file name is specified as k3-am654-base-board-ddr4-1600MHz.dtsi.
Since 1600MHz is misleading, rename it to
k3-am654-base-board-ddr4-1600MTs.dtsi
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
U-Boot cleans and invalidate L1 and L2 caches before jumping to Linux
by set/way in cleanup_before_linux(). Additionally there is a custom
hook provided to clean and invalidate L3 cache.
Unfortunately on K3 devices(having a coherent architecture), there is no
easy way to quickly clean all the cache lines for L3. The entire address
range needs to be cleaned and invalidated by Virtual Address. This can
be implemented using the L3 custom hook but it take lot of time to clean
the entire address range. In the interest of boot time this might not be
a viable solution.
The best hit is to make sure the loaded Linux image is flushed so that
the entire image is written to DDR from L3. When Linux starts running with
caches disabled the full image is available from DDR.
Reported-by: Andrew F. Davis <afd@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Once the arch specific boot_prepare_linux completes, boards wants to
have a custom preparation for linux. Add support for a custom
board_prep_linux.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add usb peripheral and usb phy nodes in spl to enable SPL_DFU bootmode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdspnqAAoJEB6zHgIOrC/Ixi4IAJEEiCZPu6Z3fbkFX/Um7vCX
eMTltJN8nz4oiSi3xdx3ejueqWdW3F8VuCkHb0j0bVAhMlUlVgwCzfd0cD+D2iwS
jkrgzASNAr+JeYKYEdWqqfaUxOCd2qfuBu9EXlpvKQLWLt+KRfsOsHWcgR4bf095
aGCihvd/fKhKYUvbf5cEQnsWa3UwtsKk4Web5MKjxXx3p0iVNlu4KLd/vDWfTios
X1NqiO5ZjXNrDxyG6Aj8lgDXlE5kfeKaN/aCJU1/0U2cXm8JRu2w2dv1P/e/kU+j
NHIGzICAG4Lk/4gQTeuohJxLyvj7K3i1H12ik9Qeh4H1/5fsyybyltGUo7H443s=
=JYe3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2020.01 cycle
This feature set includes Eugen's work on a new tiny flexcom driver and
eeprom mac retrieval for the sam9x60-ek board.
The Allwinner H6 SoC has a register to set the PIO banks' voltage. When
it mismatches the real voltage supplied to the VCC to the PIO supply,
the PIO will work improperly.
The PIO controller also has a register that contains the status of each
VCC rail of the PIO supplies, and it has the same definition with the
configuration register. so we can just copy the content of this register
to the configuration register at startup, to ensure the configuration is
correct at startup stage.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[jagan: s/__maybe__unused/__maybe_unused]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Sync Kernel DTS for Allwinner H6 boards.
Drop /omit-if-no-ref/ keyword as it's not supported by U-boot.
commit <d45331b00ddb> Linux 5.3-rc4
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
clock_sun6i.c is used for sun6i, sun8i and sun50i SoC families.
PLL1 clock sets the default system clock, defined as:
sun6i: 1008000000
sun8i: 1008000000
sun50i: 816000000
With the current calculation, m = 2 and k = 3. Solving for n,
this results 28. Solving back:
(24MHz * 28 * 3) / 2 = 1008MHz
However if the requested clock is 816, n is 22.66 rounded
to 22, which results:
(24MHz * 28 * 3) / 2 = 792MHz
Changing k to 4 satisfies both system clocks:
(24E6 * 21 * 4) / 2 = 1008MHz
(24E6 * 17 * 4) / 2 = 816MHz
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
The Linux kernel upstream has chosen to create and use a separate device tree
for the eMMC variants instead of adding eMMC support existing device tree. These
changes to Linux kernel are queued for Linux 5.4.
commit <02bb66b347ff8115f53948f86b884e008ba385b9> ("arm64: dts:
allwinner: a64: Add A64 OlinuXino board (with eMMC)")
This patch has been tested on A64-OLinuXino-1Ge16GW and is based on Linux
device-tree and a64-olinuxino_defconfig.
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
[jagan: updated linux-next commit details]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Half DQ configuration seems to be very rare for H6 based boards/STBs,
but exists nevertheless. Currently the only known product which needs
this support is Tanix TX6 mini.
This commit adds support for half DQ configuration. Code was tested
for regressions on other configurations (OrangePi 3 1 GiB/LPDDR3, Tanix
TX6 4 GiB/DDR3) and none were found.
Thanks to Icenowy Zheng for help with this code.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: thomas graichen <thomas.graichen@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
SoPine has winbond SPI-FLASH, so enable the same in defconfig
and add aliases for spi0 in -u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPI is available in Allwinner A64 SoC, so enable it
globally in Kconfig.
- CONFIG_SPI
- CONFIG_DM_SPI
- CONFIG_DM_SPI_FLASH
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for System Controller available on e-a2197-00 base board.
System is very similar to p-a2197-00 board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_early_init_f added by commit e6cc3b25d7
("arm: zynq: Wire watchdog internals") is no longer needed that's why
remove it also with Kconfig enabling.
Fixes: ccd063e981 ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are use cases where lpd watchdog can be configured for APU use. By
design this IP should be listed in zynqmp.dtsi to make sure that node is
properly enabled by DTG.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch updates the nand device tree node properties as per
updated driver.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add gpio phy reset via I2C expander TCA6416 on board ZCU102.
A warning call trace is observer in probe when this reset is called
from context that can sleep. Keep this commented until that is
resolved in phylib.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The DP83867 strap control workaround is already present in Linux kernel
mainline binding. All these Xilinx boards require this quirk.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The si570 clock frequency should be 156.25MHz as per datasheet.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently zcu102 Rev1.0 board includes RevA sdhci dt node which has
no-1-8-v property. Since Rev1.0 has level shifters delete this
property to enable support for 1.8v.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mainline has done this switch and there is no reason not to switch it too.
Mainline U-Boot patch which has done that switch:
"dts: switch spi-flash to jedec, spi-nor compatible"
(sha1: ffd4c7c2ec)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added tps53679 compatible string to tps53681. They are both compatible to
each other and tps53679 has Linux driver already.
Signed-off-by: Nishant Mittal <nishant.mittal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ethernet phys based on devicetree specification should be using
ethernet-phy@ node name instead of pure phy@.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP based System controller is present on Versal boards. This patch is
aligning names with Versal to follow the spec.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DT binding was reviewed in Linux by commit b0b41af12a1b
("dt-bindings: memory: Add pl353 smc controller devicetree binding
information") that's why this fragment can be also added to U-Boot
repository.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove macros which use PM_SIP_SVC offset and convert invoke_smc() to
xilinx_pm_request() which do calculation with PM_SIP_SVC already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
versal_pm_request() and invoke_smc() are almost the same. Only one
difference is that versal_pm_request is adding PM_SIP_SVC offset to api_id.
The patch is moving platform implementation to firmware driver code for
synchronization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
As the PHY driver now handles the transitions of USB power domain, we
must add this information in the node of each PHY.
Also, the phy are expected in the "phys" property, not "usb-phys".
Also add the aliases for the USB ports on boards with more than a single
port.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
J721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node for the
same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add DT node for HyperBus Memory Controller in the FSS. On J721e, its not
possible to use OSPI0 and HBMC simultaneously as they are muxed within
the Flash Subsystem hence disable HBMC by default as keep OSPI enabled.
Bootloader will fixup DT when it detects HyperFlash instead of OSPI.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
To allow OCRAM to be used as wakeup source in
deep sleep, do not power it down.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The patch adds an errata ID A-008646 for workaround
to provide more information by errata ID.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2160A/LX2120A/LX2080A SVR value should be
0x873600/0x873620/0x873602
Previous values were valid only if CAN fuse is blown.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
ls1028a has 4 personalities: ls1028a, ls1027a, ls1017a and ls1018a.
Both ls1027a and ls1017a personalities are lower functionality version
which doesn't support the multimedia subsystems, like LCD, GPU.
To disable multimedia feature on non-multimedia version,
set the status property to disabled in dts nodes.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Program register bit of SCFG_SNPCNFGCR_USBxRDSNP and
SCFG_SNPCNFGCR_USBxWRSNP(x = 1, 2, 3) to drive USBx read/write
snoop signal on LS1043A and LS1046A.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add LS1027A, LS1018A and LS1017A personalities support to
LS1028A SoC family.
LS1028A is the prime personality of LS1028A SoC family.
LS1027A is a lower funtionality version of QorIQ LS1028A
which does not support the multimedia subsystems, such as LCD
controller, GPU, and eDP PHY.
The QorIQ LS1018A and LS1017A SoCs are single 64-bit Arm A72
core, low power versions of the QorIQ LS1028A and LS1027A
SoCs respectively.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Rename meson-g12a-u-boot.dtsi into meson-g12-common-u-boot.dtsi to
match the new DT architecture and add meson-sm1-sei610-u-boot.dtsi
to handle the U-Boot specific DT for graphics.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Values imported from Linux driver, but in correct numeric order.
Khadas VIM3 prints: Amlogic Meson G12B (A311D) Revision 29:b (10:2)
Cc: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Write SoC instead of Soc. The Linux driver is not affected.
Fixes: f41d723b9f ("ARM: meson: display Amlogic SoC Information")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In Linux meson-g12-common.dtsi was introduced as well as new g12b nodes
and headers, as dependencies of new meson-g12b-a311d-khadas-vim3.dts.
Copied from da0c9ea146cb ("Linux 5.4-rc2")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Like the meson-gx support, add the U-Boot specific bits in DT
to support graphics on G12A SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
If VIDEO_MESON is enabled, we need to setup the fdt for the framebuffer.
Call meson_vpu_rsv_fb() which reserves the framebuffer memory region for
EFI, and sets up simple-framebuffer nodes if simplefb support is
enabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y.
The maintainer Lukasz Dalek suggested to remove the board.
https://lists.denx.de/pipermail/u-boot/2019-August/380685.html
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[trini: As this is the last non-toradex PXA board, update travis too]
Signed-off-by: Tom Rini <trini@konsulko.com>
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
-----BEGIN PGP SIGNATURE-----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=J8jd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191014' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191014
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
THe RVT data includes a major and minor version in its header
parameter. Add a new command to print this out.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
i.MX7ULP uses the same MMDC controller IP as found on i.MX53
and i.MX6, so build mmdc_size.c for i.MX7ULP as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The original imx_ddr_size() implementation had some
issues reported by checkpatch like this:
CHECK: Prefer kernel type 'u32' over 'uint32_t'
#127: FILE: arch/arm/mach-imx/mmdc_size.c:16:
+ uint32_t ctl;
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
#151: FILE: arch/arm/mach-imx/mmdc_size.c:40:
+ unsigned ctl = readl(&mem->ctl);
Fix all of them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Place imx_ddr_size() into a separate file.
The motivation for doing this is to be able to easily reuse
imx_ddr_size() on i.MX7ULP.
Currently imx_ddr_size() is inside arch/arm/mach-imx/cpu.c, which
is not built for i.MX7ULP.
Changing the logic to allow building cpu.c for i.MX7UP would
require adding several ifdef's, leading to a not a very elegant
solution.
To allow better reuse, just place imx_ddr_size() into a common
mmdc_size.c file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
When running SPL on iMX8, the A core starts at address 0
which is a alias to OCRAM 0x100000.
The alias only map first 96KB of OCRAM, so this require the
SPL size can't beyond 96KB. But when using SPL DM, the size increase
significantly and may exceed 96KB.
So to fix the problem, we will change SPL linker address to OCRAM
address 0x100000. And then jump to the absolute address not the PC relative
address for entering OCRAM.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch converts the TPC70 to use driver model and device tree
description in both SPL and u-boot proper.
Notable changes (DM/DTS conversion):
- PINCTRL{_IMX6}
- DM_I2C
- enable 'regulator' and 'pmic' commands
- DM_MMC and BLK (USDHC)
- DM_ETH
- DM WDT (including SYSRESET)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit adds new file - imx6q-kp-u-boot.dtsi with a set of u-boot
specific properties for imx6q KP device.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
With the 256KB of OCRAM available to SPL now, there should be
enough room to enable the pinmuxing in SPL from the device tree.
This patch enables SPL_PINCTRL et al and adds the serial and
usdhc pin mux references to the -u-boot.dtsi file so the pins can be
configured from the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of
96Boards community and complies with all Consumer Edition board
specifications.
https://www.novtech.com/products/meerkat96.htmlhttps://www.96boards.org/product/imx7-96/
The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
With these support, it's good enough for loading Linux Kernel from SD or
Ethernet over USB.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If an exception occurs in a loaded image and the relocation offset is
unknown, it is helpful to know the instructions pointed to by the
program counter. This patch adds the missing output.
A possible output is:
Code: 910c4021 aa1303e0 f9400662 d63f0040 (e7f7defb)
The parentheses indicate the instruction causing the exception.
The output can be disassembled using scripts/decodecode:
echo 'Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb)' | \
ARCH=arm64 scripts/decodecode
Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb)
All code
========
0: 90000360 adrp x0, 0x6c000
4: 9100b800 add x0, x0, #0x2e
8: 94002782 bl 0x9e10
c: 17ffff8f b 0xfffffffffffffe48
10:* e7f7defb .inst 0xe7f7defb ; undefined <-- trapping instruction
Code starting with the faulting instruction
===========================================
0: e7f7defb .inst 0xe7f7defb ; undefined
We already have implemented the same for armv7.
For testing command 'exception undefined' can be used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
readb is unconditionally defined earlier in io.h, so there's no point
checking whether it's undefined.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
No ARM board seems to define __mem_pci - and if it did, one would get tons of
./arch/arm/include/asm/io.h:307:0: warning: "readl" redefined
warnings, because readl and friends are unconditionally defined
earlier in io.h. Moreover, the redefinitions lack the memory barriers
that the first definitions have. So I'm guessing this is practically
dead code.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
If there is any failure during IOdelay recalibration sequence, IOs are
not guaranteed to behave as expected. So hang on any failure during the
sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When an error is reported in __recalibrate_iodelay_start(), de-isolation
of IO doesn't happen. Because of this, undefined behaviour is observed
on many peripherals without any error. So make sure io is out of isolation
at the end of iodelay recalibration.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Main uart0 is used as debug console by both R5SPL and A72 bootloader and
Linux. So mark it as shared device so that power-domain request is
successful by both cores.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
- add BOARD_LATE_INIT function calls in board.c
- add swi_status detection in board.c
- mux: add guardian interfaces to single pinmux structure
- am33xx, kconfig: add BOARD_LATE_INIT for GUARDIAN board
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Before the priming begins, we need to disable RMW (Read Modify Write)
and disable ECC verification for read accesses. By default, the EMIF
tool enables RMW and read accesses in the EMIF_ECC_CTRL_REG.
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
If ECC is enabled, we need to ensure interleaving is disabled for higher
address space.
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
ecc_address_range registers contains the start address and end address
of the DDR address space. But the ddr driver is assuming the register
contains the start address and size of the DDR address space. Because
of this the ecc enabling is failing for the 2nd range of ecc addresses.
Fix this calculation.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This follows the linux header rules to avoid conflict bitfields.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This adds PCIe and its PHY nodes for MT7623.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This commit add a spi-nor device in the bcm96850xref device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Kursad Oney <kursad.oney@broadcom.com>
This commit add a hsspi controller in the bcm6858 device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Kursad Oney <kursad.oney@broadcom.com>
This change adds a spi nor flash device to the bcm963158 board.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
This change adds the hsspi controller to the 63158 dtsi.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
The A72 U-Boot code loads and boots a number of remote processors
including the C71x DSP, both the C66_0 and C66_1 DSPs, and the various
Main R5FSS Cores. In order to view the code loaded by the U-Boot by
remote cores, U-Boot should configure the memory region with right
memory attributes. Right now U-Boot carves out a memory region which
is not sufficient for all the images to be loaded. So, increase this
carve out region by 256MB.
Signed-off-by: Kedar Chitnis <kedarc@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The A53 U-Boot code can load and boot the MCU domain R5F cores (either a
single core in LockStep mode or 2 cores in Split mode) to achieve various
early system functionalities. Change the memory attributes for the DDR
regions used by the remote processors so that the cores can see and
execute the proper code loaded by U-Boot.
These regions are currently limited to 0xa0000000 to 0xa2100000 as per
the DDR carveouts assigned for these R5F cores in the overall DDR memory
map.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM65x SoCs has a single dual-core Arm Cortex-R5F processor
subsystem/cluster (MCU_R5FSS0) within the MCU domain. This cluster
can be configured at boot time to be either run in a LockStep mode
or in an Asymmetric Multi Processing (AMP) fashion in Split-mode.
This subsystem has 64 KB each Tightly-Coupled Memory (TCM) internal
memories for each core split between two banks - ATCM and BTCM
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5 clusters such as the absence of
an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT node for the MCU domain R5F cluster/subsystem, the two
R5 cores are added as child nodes to the main cluster/subsystem node.
The cluster is configured to run in Split-mode by default, with the
ATCMs enabled to allow the R5 cores to execute code from DDR with
boot-strapping code from ATCM. The inter-processor communication
between the main A72 cores and these processors is achieved through
shared memory and Mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have a single TMS320C71x DSP Subsystem in the MAIN
voltage domain containing the next-generation C711 CPU core. The
subsystem has 32 KB of L1D configurable SRAM/Cache and 512 KB of
L2 configurable SRAM/Cache. This subsystem has a CMMU but is not
used currently. The inter-processor communication between the main
A72 cores and the C711 processor is achieved through shared memory
and a Mailbox. Add the DT node for this DSP processor sub-system
in the common k3-j721e-main.dtsi file.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have two TMS320C66x DSP Core Subsystems (C66x CorePacs)
in the MAIN voltage domain, each with a C66x Fixed/Floating-Point DSP
Core, and 32 KB of L1P & L1D configurable SRAMs/Cache and an additional
288 KB of L2 configurable SRAM/Cache. These subsystems do not have
an MMU but contain a Region Address Translator (RAT) sub-module for
translating 32-bit processor addresses into larger bus addresses.
The inter-processor communication between the main A72 cores and
these processors is achieved through shared memory and Mailboxes.
Add the DT nodes for these DSP processor sub-systems in the common
k3-j721e-main.dtsi file.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have 3 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster (MCU_R5FSS0) is present within
the MCU domain, and the remaining two clusters are present in the
MAIN domain (MAIN_R5FSS0 & MAIN_R5FSS1). Each of these can be
configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. These
subsystems have 64 KB each Tightly-Coupled Memory (TCM) internal
memories for each core split between two banks - ATCM and BTCM
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5 clusters such as the absence of
an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT nodes for these two MAIN domain R5F cluster/subsystems,
the two R5 cores are each added as child nodes to the corresponding
main cluster node. Configure SS0 in split mode an SS1 in lockstep mode,
with the ATCMs enabled to allow the R5 cores to execute code from DDR
with boot-strapping code from ATCM.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have 3 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster (MCU_R5FSS0) is present within
the MCU domain, and the remaining two clusters are present in the
MAIN domain (MAIN_R5FSS0 & MAIN_R5FSS1). Each of these can be
configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. These
subsystems have 64 KB each Tightly-Coupled Memory (TCM) internal
memories for each core split between two banks - ATCM and BTCM
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5 clusters such as the absence of
an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT node for the MCU domain R5F cluster/subsystem, the two
R5 cores are added as child nodes to the main cluster/subsystem node.
The cluster is configured to run in LockStep mode by default, with the
ATCMs enabled to allow the R5 cores to execute code from DDR with
boot-strapping code from ATCM. The inter-processor communication
between the main A72 cores and these processors is achieved through
shared memory and Mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Although we currently use the MAIN_UART0 for R5 SPL console output there
are cases where we require access to the MCU_UART0 as well for example in
case of UART-based Y-Modem boot. To support these scenarios add related
DTS definitions to be able to use that UART early on.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
In order to allow booting TI K3 family SoCs via Y-Modem add support for
loading System Firmware by tapping into the associated SPL core loader
function.
In this context also make sure a console is available and if not go
ahead and activate the early console feature which allows bringing up
an alternate full console before the main console is activated. Such
an alternate console is typically setup in a way that the associated
UART can be fully initialized prior to SYSFW services being available.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Implement an early console functionality in SPL that can be used before
the main console is being brought up. This helps in situations where the
main console is dependent on System Firmware (SYSFW) being up and running,
which is usually not the case during the very early stages of boot. Using
this early console functionality will allow for an alternate serial port
to be used to support things like UART-based boot and early diagnostic
messages until the main console is ready to get activated.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Pick minor changes from the downstream DT, disable MMC, add GMAC0 node
and adjust PHY skew settings for GMAC1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdnCy/AAoJEB6zHgIOrC/Izp4IAJVDE0oyOYcwBoCsAqa8zvMJ
/G815T1TGyc6674TQ+Px47t+1O9InClag576E1ttKVSZHnTqH9AW1aGdVqYFgmwu
bbk7a/N2bSYc1ZruiH1YMzwVMTmwaIvn9cvNeBMkQ0cXBP6R7m9DsupaTG9mNsll
7wNFF6gZCOXQEOL6hgxerxr6UM2xaQMpSqfYhfYfmHyU0S86Cr1J7dORL1MHhZ4/
WLVuxCPpgeTwiZ0i9TerC0eH0agPQ2dmtDPAQFn+RihVS29YNDTaR+a4XVKJJ6hs
Y/77d0JYmPSY5JgYLAdjqx+GQKKqy9kpdHJz+sXCiolDdYHmG3c+4zQzrLzkH+k=
=Y0qG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2020.01 cycle
The feature set includes support for two new boards from Microchip AT91:
The sama5d27_wlsom1_ek , an evaluation kit which includes the SAMA5D2
SOC packaged in a 256 MB LPDDR2 SIP, on a SOM including wireless, which
is placed on evaluation kit with sd-card, ethernet, LCD, Camera sensor,
QSPI, etc
The sam9x60ek, an evaluation kit for the new SoC based on ARM926j , the
SAM9X60 . The evaluation kit includes NAND flash, QSPI, Ethernet, Audio,
Camera sensor connector, etc.
The full support for sam9x60ek will come at a later time. There are
still missing bits regarding the clock support and power management
controller.
Apologies to everyone whose board I broke by attempting to return
MMC1 or MMC2. I misunderstood how the MMC indexing worked.
This reverts commit 14d319b185.
Signed-off-by: Adam Ford <aford173@gmail.com>
Since convert dm_video, unused code introduced, so remove this
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
To avoid hardcoded offset when adding u-boot.cnt to flash.bin, we use
flexible offset which is calculated based on the size of the container
image generated int the first stage. And pad u-boot.cnt at 1KB
alignment.
So add code to get the offset when SPL loading u-boot.cnt.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Import i.MX8MM pin func from Linux Kernel,
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Import i.MX8MM dtsi from Linux Kernel,
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because we need to get cpu freq in print_cpuinfo at very early stage,
so we need to make sure the ccm be probed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When DM_MMC enabled, the USDHC index in U-Boot is the USDHC port.
To directly return devno, we could avoid add board specific code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce clk implementation for i.MX8MM, including pll configuration,
ccm configuration. Mostly will be done clk dm driver,
but such as DRAM part, we still use non clk dm driver, because we
have limited sram.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MQ and i.MX8MM use different analog pll design, but they
share same ccm design.
Add clock_imx8mq.h for i.MX8MQ
keep common part in clock.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To i.MX8MM SCTR clock is disabled by ROM, so before timer init
need to enable it.
To i.MX8MQ, it does not hurt the clock is enabled again.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set trustzone region 0 to allow both non-secure and secure access
when trust zone is enabled. We found USB controller fails to access
DDR if the default region 0 is secure access only.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
set the BYPASS ID SWAP bit (GPR10 bit 1) in order for GPU not to
generated AXI bus errors with TZC380 enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When running with OPTEE, the MMU table in u-boot does not remove the OPTEE
memory from its settings. So ARM speculative prefetch in u-boot may access
that OPTEE memory. Due to trust zone is enabled by OPTEE and that memory
is set to secure access, then the speculative prefetch will fail and cause
various memory issue in u-boot.
The fail address register and int_status register in trustzone has logged
that speculative access from u-boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MM has similar architecture with i.MX8MQ, but it has totally
different PLL design and register layout change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is no HDMI on i.MX8MM, so we need to remove HDMI entry, then
we could not reuse imximage.cfg, so create a new one.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix the FIT image metadata for i.MX8 to result in the intended boot
order (SPL -> ATF -> U-Boot).
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Similar to "spl_sd.cfg", this patch introduces "spl_qspi.cfg" so that
all i.MX6 based boards can use it, when they use SPL and QSPI boot
mode.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch adds the missing boot mode detection for QSPI boot on
i.MX6UL/ULL. Without it, booting with SPL from QSPI NOR does not work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
The default CSF_SIZE defined in Kconfig is too high and SPL cannot
fit into the OCRAM in certain cases.
The CSF cannot achieve 0x2000 length when using RSA 4K key which is
the largest key size supported by HABv4.
According to AN12056 "Encrypted Boot on HABv4 and CAAM Enabled Devices"
it's recommended to pad CSF binary to 0x2000 and append DEK blob to
deploy encrypted boot images.
As the maximum DEK blob size is 0x58 we can reduce CSF_SIZE to 0x2060
which should cover both CSF and DEK blob length.
Update default_image.c and image.c to align with this change and avoid
a U-Boot proper authentication failure in HAB closed devices:
Authenticate image from DDR location 0x877fffc0...
bad magic magic=0x32 length=0x6131 version=0x38
bad length magic=0x32 length=0x6131 version=0x38
bad version magic=0x32 length=0x6131 version=0x38
spl: ERROR: image authentication fail
Fixes: 96d27fb218 (Revert "habv4: tools: Avoid hardcoded CSF size for SPL targets")
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Add support for the power domain controller that's used on the
i.MX8MQ. This will be needed to be able to power on the PCIe
controller. Bindings taken from Linux, driver implementation
taken from the i.MX8 power domain controller and adjusted for
the i.MX8M SoC.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
After this change it is possible to use imx28-<board>-u-boot.dtsi with
the imx28-u-boot.dtsi explicitly included without breaking setup from
imx28-<board>.dts file.
The problem is that the imx28.dtsi included in a wrong place overrides the
changes made in imx28-<board>.dts. As a result some devices are "disabled"
in the final DTB.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change tries to fix the following problem:
- The board boots (to be more precise - ROM loads SPL) from a slow SPI-NOR
memory.
As a result the spl_boot_device() will return SPI-NOR as a boot device
(which is correct).
- The problem is that in 'falcon boot' the eMMC is used as a boot medium to
load kernel from its partition.
Calling spl_boot_device() will break things as it returns SPI-NOR device.
To fix this issue the new CONFIG_SPL_FORCE_MMC_BOOT Kconfig flag is
introduced to handle this special use case. By default it is not defined,
so there is no change in the legacy code flow.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit enables support for CONFIG_WDT in the U-Boot proper. Moreover,
the SYSRESET_WATCHDOG driver is used to support 'reset' command.
As SPL is not yet ready for DM conversion, the CONFIG_HW_WATCHDOG is
enabled for it. This allows the legacy SPL code to work properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not
supported as of time of this conversion.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After this commit the display5 device would use I2C driver supporting
driver model (DM_I2C).
The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize
on-bus devices according to device tree description.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add the initial support for the pico-imx6 variants.
DDR initialization is based on the TechNexion's U-Boot code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Allow enable_ipu_clock() to be built for SPL code. This is done
in preparation for configuring the NoC registers on i.MX6QP in SPL.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add sc_pm_is_partition_started to check whether a partition
has been started. This will be used to detect M4 partition booted up or
not, then we could choose which dtb to use. If M4 is up, we need
use dtb, such as imx8qm-mek-rpmsg.dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add OP-TEE device tree node for Linux according to args passed from ATF.
If ATF has been built with OP-TEE running, boot_pointer[1] will indicate
that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX8QM, sid is programmable, so we could program sid according the
value encoded in device tree.
This patch support legacy bindings which are still being used by XEN
and new bindings used by Linux Kernel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When resource is not assigned to non-secure Linux, if linux continue
to use the node, linux may crash or hang. So need to set the node
status to disabled for not owned resources.
The resource id is in the power-domains property in device tree,
so parse the power-domains property to get the resource id and
use scfw api to check whether it is owned by current partition.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since SCU MU driver has been bound in dm_init, so we don't need to
bind it again. Just replace by using uclass function to probe it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add parsing i.MX8 Container file support, this is to let
SPL could load images in a container file to destination address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The changes were added by following patch:
commit <9002e735e717> ("imx: mx6sabresd: fix boot hang with video")
commit <f45ec8fcfb86> ("imx6: dts: add 'u-boot, dm-pre-reloc' to soc and ipu nodes")
Let's move the U-Boot specific change to imx6qdl-u-boot.dtsi
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000.
mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig
file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On i.MX7ULP B0, there is change in NIC clock dividers architecture.
On A0, the NIC1 BUS and EXT dividers were in a chain with NIC1 DIV, but
on B0 they are parallel with NIC1 DIV. So now the dividers are independent.
This patch modifies the scg_nic_get_rate function according to this change.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The normal target frequency for ULP A7 core is 500Mhz, but now ROM
set the core frequency to 413Mhz. So change it to 500Mhz in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider
set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU
is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28)
to workaround the problem. The correct fix should let GPU handle the
clock rate in kernel.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The num/denom is a float value, but in the calculation it is convert
to integer 0, and cause the result wrong.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wrong I2c driver configuration name is used in codes, so I2c driver is
not built. Correct it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since many drivers need this CONFIG_MX7ULP to distiguish the settings
for i.MX7ULP only. Add this entry to cpu's kconfig.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The offset for FRAC and the mask for PCD are not correct.
If we set FRAC, we can't get the right frequency. Fix them
to correct value.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX7ULP, value zero is reserved in SCG1 RCCR register,
so the val should be decreased by 1 to get the correct clock
source index.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board will reboot if A7 core enter mem mode by rtc, then M4 core
enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode
to fix this issue.
Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access
it. So check the CPU rev and not apply the settings for B0.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
There is no need to use HAB for FIT signature validation when
SPL_FIT_SIGNATURE is also enabled, as that will be validated via the
normal U-Boot signed FIT image flow.
This allows having SPL validated by HAB and the payloads to follow
being validated with FIT signatures only.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q
variants, which are quite similar and already managed via only one
dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in
order to automatically enable the HAS_CAAM and MX6_SMP features.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Pass spl_image and bootdev to board_return_bootrom.
i.MX8MN needs the args to let ROM to load images
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To support DM_VIDEO,
Add display node for lcdif
Drop board iomuxc settings.
Enable DM_VIDEO
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible
with i.MX6ULL. so most code of i.MX6ULL can be reused
by i.MX6ULZ.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add i.MX6ULZ cpu type and helper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Import kernel dts for i.MX6ULZ from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6ULL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6UL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Move the exisiting function of getting board dtb from versal to a common
Xilinx folder.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With new mailbox driver PMUFW configuration object can be loaded via the
same interface and there is no need to have pmu_ipc.c completely.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
