Allow the inclusion of libfdt.h in C++ source.
Signed-off-by: Laurent Gregoire <laurent.gregoire@tomtom.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The mpc8313erdb board currently sets DBAT6 to cover all of the final 256MiB of
address space; however, not all of this space is covered by a device. In
particular, flash sits at 0xfe000000-0xfe7fffff, and nothing is mapped
at the far end of the address space.
In zlib, there is a loop that references p[-1] if p is non-NULL. Under
some circumstances, this leads to the CPU speculatively loading from
0xfffffff8 if p is NULL. This leads to a machine check.
Signed-off-by: Scott Wood <scottwood@freescale.com>
continuation to the remaining mpc83xx boards that suffer from the same problem.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 04e11cf3 "rtc: add support for 4543 RTC (manufactured by e.g.
EPSON)" introduces the following build error on boards configuring e.g,
the ds1374 rtc:
Configuring for MPC837XEMDS board...
ds1374.c:103: error: static declaration of 'rtc_read' follows non-static declaration
/home/r1aaha/git/u-boot/include/rtc.h:64: error: previous declaration of 'rtc_read' was here
ds1374.c:104: error: conflicting types for 'rtc_write'
/home/r1aaha/git/u-boot/include/rtc.h:65: error: previous declaration of 'rtc_write' was here
this reverts the erroneous chunk.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
CC: Detlev Zundel <dzu@denx.de>
CC: Andreas Pfefferle <ap@denx.de>
* Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx
* Introduce determine_mp_bootpg() helper. We'll need this to address a
bug introduced in v2009.03 with 86xx MP booting. We have to make sure
to reserve the region of memory used for the MP bootpg() so other
u-boot code doesn't use it.
* Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to
allow cmd_mp.c to build and work. In the future we should look at
implementing all these functions. This could be common w/85xx if we
use spin tables on 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is a workaround for MPC8569 CPU Errata, which needs to set Bit 13 of
LBCR in 4K bootpage. We setup a temp TLB for eLBC controller in bootpage,
then invalidate it after LBCR bit 13 is set.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- support mirrored DIMMs, not support register DIMMs
- test passed on P2020DS board with MT9JSF12872AY-1G1D1
- test passed on MPC8569MDS board with MT8JSF12864HY-1G1D1
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Travis Wheatley <travis.wheatley@freescale.com>
The masks for various bit defines of LSDMR are common and thus we can
define them in one place rather than replicating them in each config.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Divisor field is called PTV not PVT.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds the board specific communication routines needed by
the external 4543 RTC.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>
This patch adds advanced diagnosis functions for the inka4x0 board.
Signed-off-by: Andreas Pfefferle <ap@denx.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Other commands implementing subcommands can reuse this code nicely.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>
Current u-boot top of tree builds with warnings/errors for
the following boards:
ads5121 cpci5200 mecp5200 v38b IAD210 MBX MBX860T NX823
RPXClassic debris PN62
following patch solves this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Enabling the instruction cache significantly accelerates U-Boot
operations like CRC checking, image uncompression, etc.
Kudos to Andrea Scian for pointing out.
Signed-off-by: Wolfgang Denk <wd@denx.de>
http://www.denx.de/wiki/DULG/UBootCmdGroupFlash#UBootCmdFlMtdparts
provides a flexible way to create and maintain u-boot mtd
partitions. This allows commands such as "nand erase fs"
to work and the user no longer needs to decode the absolute
nand offsets. This patch enables this function for beagleboard
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Since all of the bf537-stamp and bf537-ezkit boards out there can handle it,
increase the speed of SCLK to 125MHz rather than 100MHz.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use the common net eth functions to setup the env/global data with the MAC
address, and properly handle the case where CONFIG_SYS_NO_FLASH is defined.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the hardware can handle it, bump the default clocks from 80mhz SCLK
and 398mhz CCLK to 100mhz SCLK and 498mhz CCLK.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Again, don't clobber pins that we aren't actually using, and use the common
LED framework rather than our own hob-job-but-not-really-working.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than duplicate the same ADI settings in every ADI board, create a
common ADI config header and have all ADI boards start using that. This
will also make merging the ~10 boards I have to forward port a lot easier.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patches configures the NAND UPM-FSL driver with multi-chip
support for the Micron MT29F8G08FAB NAND flash memory on the
TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For the NAND chips on the TQM8548 modules, a special chip-select logic is
used. It uses dedicated address lines to be set via UPM machine address
register (mar). This patch adds such support to the FSL-UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The SPORT_TX registers cannot be read (the hardware will trigger an error),
so drop the read helper macros.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The U-Boot UBIFS implementation is largely a direct copy from the current
Linux version (2.6.29-rc6). As already done in the UBI version we have an
"abstraction layer" to redefine or remove some OS calls (e.g. mutex_lock()
...). This makes it possible to use the original Linux code with very
little changes. And by this we can better update to later Linux versions.
I removed some of the Linux features that are not used in the U-Boot
version (e.g. garbage-collection, write support).
Signed-off-by: Stefan Roese <sr@denx.de>
CC: Artem Bityutskiy <dedekind@infradead.org>
CC: Adrian Hunter <ext-Adrian.Hunter@nokia.com>
This patch adds LZO decompression support to U-Boot. It is needed for
the upcoming UBIFS support, since UBIFS uses LZO as default compressor/
decompressor. Since we only support read-only in UBIFS, only the
decompressor is needed.
All this is copied with minor changes from the current Linux kernel
version (2.6.28-rc8).
This patch only implements this LZO decompressor support for PPC.
Other platforms using UBIFS will have to add the required
"include/asm/unaligned.h" as well. It should be fairly easy to copy this
from the Linux source tree as I have done it for PPC in this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch replaces in/out8/16/32 macros by in/out_8/_be16/_be32
macros. Also volatile pointer references are replaced by the
new accessors.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Fix building DASA_SIM boards by increasing U-Boot's size in flash.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Rewrite interrupt handling functionality for the i386 port. Separated
functionality into separate CPU and Architecture components.
It appears as if the i386 interrupt handler functionality was intended
to allow multiple handlers to be installed for a given interrupt.
Unfortunately, this functionality was not fully implemented and also
had the problem that irq_free_handler() does not allow the passing
of the handler function pointer and therefore could never be used to
free specific handlers that had been installed for a given IRQ.
There were also various issues with array bounds not being fully
tested.
I had two objectives in mind for the new implementation:
1) Keep the implementation as similar as possible to existing
implementations. To that end, I have used the leon2/3
implementations as the reference
2) Seperate CPU and Architecture specific elements. All specific i386
interrupt functionality is now in cpu/i386/ with the high level
API and architecture specific code in lib_i386. Functionality
specific to the PC/AT architecture (i.e. cascaded i8259 PICs) has
been further split out into an individual file to allow for the
implementation of the PIC architecture of the SC520 CPU (supports
more IRQs)
Signed-off-by: Graeme Russ <graeme.russ at gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
In the ppc case, these things are part of the legacy ABI, so keep them
around but mark them as legacy so no new code will touch them.
Also stop calling load_sernum_ethaddr() since all boards now implement
this as a stub.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
Rather than have common ppc code call a board-specific function like
load_sernum_ethaddr(), have each board call it in its own board-specific
misc_init_r() function.
The boards that get converted here are:
- kup4k/kup4x
- pcs440ep
- tqm8xx
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Stefan Roese <sr@denx.de>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
Also rename load_sernum_ethaddr() to misc_init_r() so we don't need to
handle this board specially in common ARM code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
Rather than have the common ppc code have board-specific hooks, move the
board_get_enetaddr() function into the board-specific init functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
Declare new utility functions for converting between the environment
variables (eth*addr) and the binary MAC address representation. This way
we can unify all the random places that already do this kind of thing.
The functions in question:
eth_parse_enetaddr - "..." -> {...}
eth_getenv_enetaddr - env -> {...}
eth_setenv_enetaddr - {...} -> env
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
Now that our printf functions support the %pI4 modifier like the kernel,
let's drop the inflexible print_IPaddr() function and covert over to the
%pI4 modifier.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
Total5200 and digsy MTC use I2C port 2 pins as a ATA chip select.
To avoid adding board-specific ifdefs to cpu/mpc5xxx/ide.c new
define CONFIG_SYS_ATA_CS_ON_I2C2 was introduced. It is used by
Total5200 and will be used by digsy MTC and other boards with
ATA CS on I2C pins.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU
- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang
Signed-off-by: Heiko Schocher <hs@denx.de>
renaming the "mgsuvd" board port into "km8xx", because
there come more similar boards from keymile.
Compiling the mgsuvd board with "make mgsuvd_config"
remains.
Signed-off-by: Heiko Schocher <hs@denx.de>
- added to keymile-common.h:
- bootcount support
- COMMAND HISTORY
- CONFIG_AUTO_COMPLETE
- CONFIG_SYS_FLASH_PROTECTION
- JFFS2 support
- CONFIG_VERSION_VARIABLE
- extracted common I2C settings for all boards
- common default environment settings summarized
Signed-off-by: Heiko Schocher <hs@denx.de>
The rtl8139 driver use pci_mem_to_phys. So it need PCI system memory
registration.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We can built 'make sh7785lcr_32bit_config'. And add new command "pmb"
for this mode. This command changes PMB for using 512MB system memory.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Some register value was hardcoded for System memory size 128MB and
memory offset 0x08000000. This patch fixed the problem.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
it is possible that some board variants have different DDR II
RAM sizes. So we autodetect the size of the assembled RAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds I2C support for the Keymile kmeter1 board.
It uses the First I2C Controller from the CPU, for
accessing 4 temperature sensors, an eeprom with IVM data
and the booteeprom over a pca9547 mux.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The previous version rebooted forever with DDR bigger than 256MB.
Access the DS1339 RTC chip is on I2C1 bus.
Allow DHCP.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The "eet" variant of the imx31_phycore board has an OLED display, using a
s6e63d6 display controller on the first SPI interface, using GPIO57 as a
chip-select for it. With this configuration you can display 256 colour BMP
images in 16-bit RGB (RGB565) LCD mode.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch also simplifies some ifdefs in lcd.c, introduces a generic
vidinfo_t, which new drivers are encouraged to use and old drivers to switch
over to.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This is a driver for the S6E63D6 SPI OLED display controller from Samsung.
It only provides access to controller's registers so the client can freely
configure it.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This is a minimal driver, so far only managing output. It will
be used by the mxc_spi.c driver.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe
slots. Let's support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This is just a handy routine that reports last PCI busno: we walk
down all the hoses and return last hose's last_busno.
Will be used by PCI/PCIe initialization code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Currently, we get 256MB as the default, but since all the 86xx
board configs define a 2G BAT mapping for RAM, raise default
to 2G.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
There are some differences in the implementation of GPIO in the
at32uc chip compared to the ap700x series.
Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The AVR32A architecture (which AT32UC3A-series is based on) has a
different memory layout than the AVR32B-architecture. This patch moves
addrspace.h to an arch-dependent directory in preparation for
AT32UC3A-support. It also moves some address-space manipulation
functions from io.h to addrspace.h.
Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The AT32UC3A series of processors doesn't contain any cache, and issuing
cache control instructions on those will cause an exception. This commit
makes cacheflush.h arch-dependent in preparation for the AT32UC3A-support.
Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
NetLoop polls every cycle with getenv some environment variables.
This is horribly slow, especially when the environment is big.
This patch reads only the environment variables in NetLoop,
when they were changed.
Also moved the init part of the NetLoop function in a seperate
function.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Compiling dbau1x00 and gth2 boards with GCC-4.2, you would see new warnings
like this:
skuribay@ubuntu:u-boot.git$ ./MAKEALL dbau1000
Configuring for dbau1x00 board...
au1x00_eth.c: In function 'au1x00_send':
au1x00_eth.c:158: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type
au1x00_eth.c: In function 'au1x00_recv':
au1x00_eth.c:211: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type
au1x00_eth.c: In function 'au1x00_init':
au1x00_eth.c:252: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type
au1x00_eth.c: In function 'au1x00_recv':
au1x00_eth.c:211: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type
au1x00_eth.c: In function 'au1x00_init':
au1x00_eth.c:252: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type
au1x00_eth.c: In function 'au1x00_send':
au1x00_eth.c:158: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type
We're passing a volatile pointer to a function which is expecting a non-
volatile pointer. That's potentially dangerous, so gcc warns about it.
Confirmed with ELDK 4.2 (GCC 4.2.2) and Sourcey G++ 4.2 (GCC 4.2.3).
To fix this, we add a volatile attribute to the argument in question.
The virt_to_phys function in Linux kernel also does the same thing.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
This patch adds OMAP3 cpu type auto detection based on OMAP3 register
and removes hardcoded values.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
With BeagleBoard revision C some HW changes are introduced (e.g. PinMUX)
which might need different software handling. For this, GPIO pin 171 (GPIO
module 6, offset 11) can be used to check for board revision. If this pin
is low, we have a rev C board. Else it must be a revision Ax or Bx board.
To handle board differences you can call function beagle_get_revision().
E.g.:
if (beagle_get_revision()) {
/* do special revision C stuff here */
}
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Serial driver via the EmbeddedICE macrocell's DCC channel using
co-processor 14.
It does include a timeout to ensure that the system does not
totally freeze when there is nothing connected to read.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This trivially enables Ethernet support in the debug board
by setting up the proper chip select.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
This driver implements the ECC algorithm described in
the CPU data sheet and uses the OOB layout chosen in
already-released development systems (shipped with a custom-made
u-boot 1.3.1).
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
The previous merge for cleaning up the I2C driver incorrectly reverted the
CFG_xxx rename for some of the I2C defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Fixing the get_timer function to return time in miliseconds instead of
ticks. Also fixed PXA boards to use the conventional value of 1000 for
CONFIG_SYS_HZ.
Signed-off-by: Micha Kalfon <smichak.uv@gmail.com>
- activate CS4 for accessing the FPGA
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flashes in the DTS
before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k
Signed-off-by: Heiko Schocher <hs@denx.de>
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flash in the DTS
before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch will create a configuration option for a minimum configuration for
the ns16550 serial driver at drivers/serial/ns16550.c and will apply this new
configuration option to the SIMPC8313.h config file in order to fix the NAND
bootstrap build error. This option will exclude all functions with exception of
NS16550_putc and NS16550_init. This will be used primarily to save space and
remove unused code from builds in which space is limited.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
This patch prepares the good old PMC405 board support for
upcoming PMC405V2 patches.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes coding style for PMC405 board support.
Also some unneeded features/code is removed.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
1. Changes to the default environment:
- "bootcmd" defined as "run flash_self"
- "saveenv" command removed from "update"
- "uboot" changed to "u-boot" (also in "load")
- "addmtd" variable defined (and added to all boot commands)
2. CONFIG_CMD_JFFS2 defined to enable "mtdparts" command
3. MTDIDS_DEFAULT and MTDPARTS_DEFAULT defined
4. CONFIG_SYS_CBSIZE changed from 256 to 512. That solves the problem
with truncated "bootargs" environment variable.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Because the functions have been defined using macros, grepping for
their definitions is not possible. This patch adds the real function
names in comments.
Signed-off-by: Petri Lehtinen <petri.lehtinen@inoi.fi>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment. So, let's make sure the define is named accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
- Extend ub_dev_read() and ub_dev_recv() so they return the length actually
read, which allows for better control and error handling (this introduces
additional error code API_ESYSC returned by the glue mid-layer).
- Clean up definitions naming and usage.
- Other minor cosmetics.
Note these changes do not touch the API proper, so the interface between
U-Boot and standalone applications remains unchanged.
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
This patch allows using of SATA devices connected
to the onboard PCI SIL1334 SATA controller.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Here's a new framework (based roughly off the linux one) for managing
MMC controllers. It handles all of the standard SD/MMC transactions,
leaving the host drivers to implement only what is necessary to
deal with their specific hardware.
This also hooks the infrastructure into the PowerPC board code
(similar to how the ethernet infrastructure now hooks in)
Some of this code was contributed by Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The current MMC infrastructure relies on the existence of an
arch-specific header file. This isn't necessary, and a couple
drivers were forced to implement dummy files to meet this requirement.
Instead, we move the stuff in those header files into a more appropriate
place, and eliminate the stubs and the #include of asm/arch/mmc.h
Signed-off-by: Andy Fleming <afleming@freescale.com>
This errata fix is required for 32 bit DDR2 controller on 8572.
May also be required for P10XX20XX platforms
Signed-off-by: Poonam_Agarwal-b10812 <b10812@lc1106.zin33.ap.freescale.net>
The TQM8548_AG is a variant of the TQM8548 module with 1 GiB memory,
CAN and without PCI/PCI-X and RTC. U-Boot can be built for this module
with "$ make TQM8548_AG_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN
interface. With NAND support, the image is significantly larger and
TEXT_BASE is adjusted accordingly. U-Boot can be built for this
module with "$ make TQM8548_BE_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
The TQM8548_AG module does not have the standard PCI/PCI-X interface
connected but just the PCI Express interface . So far it was not
possible to disable it without disabling the complete PCI interface
(CONFIG_PCI) including PCI Express.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Update the 86xx reset sequence to try executing a board-specific reset
function. If the board-specific reset is not implemented or does not
succeed, then assert #HRESET_REQ. Using #HRESET_REQ is a more standard
reset procedure than the previous method and allows all board
peripherals to be reset if needed.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Added various p2020 processor specific details:
* SVR for p2020, p2020E
* immap updates for LAWs and DDR on p2020
* LAW defines related to p2020
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we introduced the 36-bit config of the MPC8572DS board we had the
wrong PCI MEM bus address map. Additionally, the change to the address
map exposes a small issue in our dummy read on the ULI bus. We need
to use the new mapping functions to handle that read properly in the
36-bit config.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously we only allowed power-of-two memory sizes and didnt
handle >2G of memory. Now we will map up to CONFIG_MAX_MEM_MAPPED
and should properly handle any size that we can make in the TLBs
we have available to us
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Blackfin i2c driver has been rewritten thus the special ifdefs in the
common code are no longer needed.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
With actual u-boot compiling the mgcoge port fails, because
since commit ba705b5b1a it is
necessary to define CONFIG_NET_MULTI.
Seems to me the mgcoge port is the only actual existing 8260
port who uses CONFIG_ETHER_ON_SCC, so no other 8260 port needed
to be fixed.
Signed-off-by: Heiko Schocher <hs@denx.de>
The criteria of the AMCC SDRAM Controller DDR autocalibration
U-Boot code is to pick the largest passing write/read/compare
window that also has the smallest SDRAM_RDCC.[RDSS] Read Sample
Cycle Select value.
On some Kilauea boards the DDR autocalibration algorithm can
find a large passing write/read/compare window with a small
SDRAM_RDCC.[RDSS] aggressive value of Read Sample Cycle Select
value "T1 Sample".
This SDRAM_RDCC.[RDSS] Read Sample Cycle Select value of
"T1 Sample" proves to be to aggressive when later on U-Boot
relocates into DDR memory and executes.
The memory traces on the Kilauea board are short so on some
Kilauea boards the SDRAM_RDCC.[RDSS] Read Sample Cycle Select
value of "T1 Sample" shows up as a potentially valid value for
the DDR autocalibratiion algorithm.
The fix is to define a weak default function which provides
the minimum SDRAM_RDCC.[RDSS] Read Sample Cycle Select value
to accept for DDR autocalibration. The default will be the
"T2 Sample" value. A board developer who has a well defined
board and chooses to be more aggressive can always provide
their own board specific string function with the more
aggressive "T1 Sample" value or stick with the default
minimum SDRAM_RDCC.[RDSS] value of "T2".
Also put in a autocalibration loop fix for case where current
write/read/compare passing window size is the same as a prior
window size, then in this case choose the write/read/compare
result that has the associated smallest RDCC T-Sample value.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
CONFIG_SDRAM_PPC4xx_IBM_DDR2 is not set when include/asm-ppc/config.h is
included. So for katmai, CONFIG_MAX_MEM_MAPPED will get set to 256MB.
It makes perfect sense to set CONFIG_MAX_MEM_MAPPED to 2GB for all PPC4xx
boards right now.
Signed-off-by: Stefan Roese <sr@denx.de>
At some point an intentional double space at the end of the sentence
got changed into a tab in the GPL header line:
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
This patch fixes the damage.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
If on your board is more than one flash, you must know
the size of every single flash, for example, for updating
the DTS before booting Linux. So make this function
flash_get_info() extern, and you can have all info
about your flashes.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Added new CONFIG options for the three type of MAC-PHY interconnect and
applied them all relevant board config files
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Moved CONFIG_MAX_MEM_MAPPED to the asm/config.h so its kept consistent
between the two current users (lib_ppc/board.c, 44x SPD DDR2).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
We have common defines that we duplicate in various ways. Having an
arch specific config.h gives us a common location for those defines.
Eventually we should be able to replace this when we have proper
Kconfig support.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that the rest of u-boot can support it, change the PCI bus
address of the PCI MEM regions from 0x80000000 to 0xc0000000,
and use the same bus address for both PCI1 and PCI2. This will
maximize the amount of PCI address space left over to map RAM
on systems with large amounts of memory.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Clean up PCI mapping concepts in the 8641 config - rename _BASE
to _BUS, as it's actually a PCI bus address, separate virtual
and physical addresses into _VIRT and _PHYS, and use each
appopriately.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
The BAT fields are architected; there's no need for these to be in
cpu-specific files. Drop the duplication and move these to
include/asm-ppc/mmu.h. Also, remove the BL_xxx defines that were only
used by the alaska board, and switch to using the BATU_BL_xxx defines
used by all the other boards. The BL_ defines previously in use
had to be shifted into the proper position for use, which was inefficient.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
It is no longer always true that the pci bus address can be
used as the virtual address for pci accesses. pci_map_bar()
is created to return the virtual address for a pci region.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
If the VA and PA of the flash aren't the same, the banks list
should be initialized to hold the physical address. Correct this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Driver for Dave DNET ethernet controller (used on Dave/DENX
QongEVB-LITE board).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
The PCI_REGION_MEMORY and PCI_REGION_MEM are a bit to similar and
can be confusing when reading the code.
Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY to clarify its used
for system memory mapping purposes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleanup for M5271EVB:
Added clarification on the use of CONFIG_SYS_CLOCK.
Modified to use u-boot's HUSH parser.
Cleanup on environment settings.
Removed compiler warning by defining CONFIG_SYS_CS0_*
Dependencies:
Added the use of CONFIG_SYS_MCF_SYNCR for clock multiplier.
This depends on a patch to include/asm-m68k/m5271.h
that defines the multiplier and divider ratios.
Removed the definition of CONFIG_SYS_FECI2C.
This depends on a patch that removes the use of it in
cpu/mcf52x2/cpu_init.c
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
M5271 dynamic clock multiplier. It is currently fixed at 100MHz.
Allow the board header file to set their own multiplier and divider.
Added the #define for the multiplier and divider to the cpu header file.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Move the default SPI CS that we boot from into common code so that it can
be used in other SPI drivers and environment settings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
include/flash.h was commented to say that the address in
flash_info->start was a physical address. However, from u-boot's
point of view, and looking at most flash code, it makes more
sense for this to be a virtual address. So I corrected the
comment to indicate that this was a virtual address.
The only flash driver that was actually treating the address
as physical was the mtd/cfi_flash driver. However, this code
was using it inconsistently as it actually directly dereferenced
the "start" element, while it used map_physmem to get a
virtual address in other places. I changed this driver so
that the code which initializes the info->start field calls
map_physmem to get a virtual address, eliminating the need for
further map_physmem calls. The code is now consistent.
The *only* place a physical address should be used is when defining the
flash banks list that is used to initialize the flash_info struct,
usually found in the board config file.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Original patch from Ralph Kondziella
plus clean up by Wolfgang Denk
plus changes by John Rigby
use ips clock not lpc
port forward to current u-boot release
Signed-off-by: Ralph Kondziella <rk@argos-messtechnik.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: John Rigby <jrigby@freescale.com>
IIM (IC Identification Module) is the fusebox for the mpc5121.
Use #define CONFIG_IIM to turn on the clock for this module
use #define CONFIG_CMD_FUSE to add fusebox commands.
Fusebox commands include the ability to read
the status, read the register cache, override the register cache,
program the fuses and sense them.
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
This is a port of the Linux Blackfin on-chip SDH driver to U-Boot.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Knowing the booting source of the part is useful, especially when the part
can switch dynamically between sources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Set the default CONFIG_ENV_SPI_CS value to match the SPI CS that is used by
the Blackfin on-chip bootrom to boot out of SPI flash.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is a port of the Linux Blackfin on-chip ATAPI driver to U-Boot.
Signed-off-by: Sonic Zhang <Sonic.Zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The performance difference from doing an 8 bit DMA memcpy vs an optimized
core memcpy can be pretty big when you add in the overhead of setting up the
MDMA registers, cache flushes, etc... So only use dma_memcpy() when we
actually require it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Take the cache flush functions from the kernel as they use hardware loops in
order to get optimal performance.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Calculating the clocks requires a bit of calls to gcc math functions, so
cache the values after the first run since they'll most likely never
change once U-Boot is up and running.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
instead the board will have to load it from flash or ram
which will be specified by npe_ucode env var
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch updates the default environmental variables for the
Korat PPC 440EPx board, and makes additional minor fixes.
Signed-off-by: Larry Johnson <lrj@acm.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the is_valid_ether_addr() function from the Linux kernel.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Since the SPD823TS board does not actually have any writable flash to save
its environment, undefine CONFIG_CMD_ENV so the "saveenv" command is
disabled.
This fixes the build error:
common/libcommon.a(cmd_nvedit.o): In function `do_saveenv':
common/cmd_nvedit.c:557: undefined reference to `saveenv'
make: *** [u-boot] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add BeagleBoard support, common power code and README.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Enabling USB MSC support for DM6446 (TI DaVinci) platform in the
configuration file.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Enabling DM6446 (TI DaVinci) USB module power and MUSB low-level
controller hook up to USB core layer.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Rather than forcing people to define a custom "LITTLEENDIAN", just use the
__LITTLE_ENDIAN one from the Linux byteorder headers that every arch is
already setting up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
- fix ehci_readl, ehci_writel
- introduce new define in ehci.h
- introduce the handshake function for waiting on a register
- fix usb_ehci_fsl with the new HC_LENGTH macro
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Böhmer <linux@bohmer.net>
The Blackfin JTAG has the ability to pass data via a back-channel without
halting the processor. Utilize that channel to emulate a console.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current Blackfin i2c driver does not work properly with certain devices
due to it breaking up transfers incorrectly. This is a rewrite of the
driver and relocates it to the newer place in the source tree.
Also remove duplicated I2C speed defines in Blackfin board configs and
disable I2C slave address usage since it isn't implemented.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Our dcache invalidate function doesn't just invalidate, it also flushes.
So rename the function accordingly and fix the dma_memcpy() function so it
doesn't inadvertently corrupt the data destination.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Rather than have the board code initialize SATA automatically during boot,
make the user manually run "sata init". This brings the SATA subsystem in
line with common U-Boot policy.
Rather than having a dedicated weak function "is_sata_supported", people
can override sata_initialize() to do their weird board stuff. Then they
can call the actual __sata_initialize().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds flush_/invalidate_dcache_range() to the MIPS architecture.
Those functions are needed for the upcoming dcache support for the USB
EHCI driver. I chose this API because those cache handling functions are
already present in the PPC architecture.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Lot's of 405 board config files use CONFIG_SYS_IGNORE_405_UART_ERRATA_59.
Either they define or undef it. Because it's not used in any source
files this patch removes any references to it.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Board support for the Guntermann & Drunck PowerPC 440 ETX module.
Based on the AMCC Yosemite board support by Stefan Roese.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add CONFIG_NET_MULTI in config file, because sh_eth changed new newwork API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This change is needed for mgcoge because it uses two ethernet drivers.
Add a check for the presence of the PIGGY board on mgcoge. Without this
board networking cannot work and the initialization must be aborted.
Only allocate rtx once to prevent DPRAM exhaustion.
Initialize ether_scc.c and the keymile-specific HDLC driver (to be added
soon) in eth.c.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
sh_eth used old network API. This patch changed new API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The NMDK8815 board is distributed by ST Microelectornics.
Other (proprietary) code must be run to unlock the CPU before
U-Boot runs. doc/README.nmdk8815 outlines the boot sequence.
This is the initial port, with basic infrastructure and
a working serial port.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
When compile u-boot with the 2.18 binutils the following
warning messages for each object file in post/lib_ppc/fpu/ is
produced at the linking stage:
post/libpost.a(acc1.o) uses hard float, u-boot uses soft-float
...
This is because of the fact that, in general, the soft-float and
hard-float ABIs are incompatible; the 2.18 binutils do checking
of the Tag_GNU_Power_ABI_FP attribute of the files to be linked, and
produce the worning like above if these are not compatible.
The incompatibility of ABIs is concerned only the float values:
e.g. the soft-float ABI assumes the float argument passing in the
pair of rX registers, and the hard-float ABI assumes passing of
the float argument in the fX register. When we don't pass the float
arguments between the functions compiled with different floatness,
then such an application will work correctly.
This is the case for the FPU POST: u-boot (compiled with soft-float)
doesn't pass to (and doesn't get from) the FPU POST functions any
floats; there are no functions exported from the post/lib_ppc/fpu/
objects which would work with float parameters/returns too. So, we
can reassure the linker not to worry about the difference in ABI
attributes of linking files just by setting the 'soft-float'
attribute for the objects in post/lib_ppc/fpu. And this patch does
this.
Also, to avoid passing both soft- and hard-float options in CFLAGS
when compiling the files from post/lib_ppc/fpu (which is OK, but
looks rather dirty) this patch removes the soft-float string from
CFLAGS in post/lib_ppc/fpu/Makefile.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Initial support for the DS4510, a CPU supervisor with
integrated EEPROM, SRAM, and 4 programmable non-volatile
GPIO pins. The CONFIG_DS4510 define enables support
for the device while the CONFIG_CMD_DS4510 define
enables the ds4510 command. The additional
CONFIG_DS4510_INFO, CONFIG_DS4510_MEM, and
CONFIG_DS4510_RST defines add additional sub-commands
to the ds4510 command when defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch extracts the identical config options for the
keymile boards mgcoge, mgsuvd and kmeter1 in a new
common config file keymile-common.h.
Signed-off-by: Heiko Schocher <hs@denx.de>
Check the presence of the PIGGY on the keymile boards mgcoge,
mgsuvd and kmeter1. If the PIGGY is not present, dont register
this Ethernet device.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.
- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700
Signed-off-by: Heiko Schocher <hs@denx.de>
Add a do_div() wrapper, lldiv(). The new inline function doesn't modify
the dividend and returns the result of division, so it is useful
in complex expressions, i.e. "return(a/b)" -> "return(lldiv(a,b))"
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary
to allow for larger memory sizes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The eLBC only handles 32-bit physical address in systems with 36-bit
physical. The previos generation of LBC handled 34-bit physical
address in 36-bit systems. Added a new CONFIG option to convey
the difference between the LBC and eLBC.
Also added defines for XAM bits used in LBC for the extended 34-bit
support.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the new BR_ADDR macro to properly setup the address field of the
localbus chipselects used by NAND.
This allows us to deal with 36-bit phys on these boards in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch updates e500 freqProcessor to array based on CONFIG_NUM_CPUS,
and prints each CPU's frequency separately. It also fixes up each CPU's
frequency in "clock-frequency" of fdt blob.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Some 85xx processors have the advanced power management feature,
such as wake up ARP, that needs enable the automatic self refresh.
If the DDR controller pass the SR_IT (self refresh idle threshold)
idle cycles, it will automatically enter self refresh. However,
anytime one transaction is issued to the DDR controller, it will
reset the counter and exit self refresh state.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
- The DDR3 controller is expanding the bits for timing config
- Add the DDR3 32-bit bus mode support
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Introduce a new define to seperate out the virtual address that PCI
IO space is at from the physical address. In most situations these are
mapped 1:1. However any code accessing the bus should use VIRT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Introduce a new define to seperate out the virtual address that PCI
memory is at from the physical address. In most situations these are
mapped 1:1. However any code accessing the bus should use VIRT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Use the _MEM_PHYS defines instead of _MEM_BUS for LAW and real address fields
of TLBs. This is what we should have always been using from the start.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Use CONFIG_SYS_PCI*_IO_BUS for the bus relative address instead
of _IO_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_SYS_{PCI,RIO}_MEM_BUS for the bus relative address instead
of _MEM_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Added a CONFIG_SYS_FLASH_BASE_PHYS for use as the physical address and
maintain CONFIG_SYS_FLASH_BASE as the virtual address of the flash.
This allows us to deal with 36-bit phys on these boards in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Added a PIXIS_BASE_PHYS for use as the physical address and maintain
PIXIS_BASE as the virtual address of the PIXIS fpga registers.
This allows us to deal with 36-bit phys on these boards in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
This patch will create a new board, SIMPC8313, from Sheldon Instruments. This
board boots from NAND devices and is configureable for either large or small
page devices. The board supports non-soldered DDR2, one ethernet port, a
Marvell 88E1118 PHY, and PCI host support. The board also has a FPGA connected
to the eLBC providing glue logic to a TMS320C67xx DSP.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define
#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
but that's bogus and did not work anyhow.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Rather than putting the function prototype for board_nand_init() in the one
place where it gets called, put it into nand.h so that every place that also
defines it gets the prototype. Otherwise, errors can go silently unnoticed
such as using the wrong return value (void rather than int) when defining
the function.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Add subpage write support
- Add onenand_oob_64/32 ecclayout
This has been missing and without it UBI has some incompatibilies issues
with the current (>= 2.6.27) Linux kernel version. vid_hdr_offset is
placed differently (2048 instead of 512) without this fix.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
MPC837XEMDS boards can support PCI-E via "PCI-E riser card". The card
provides two PCI-E (x2) ports. Though, only one port can be used in x2
mode. Two ports can function simultaneously in x1 mode.
PCI-E x1/x2 modes can be switched via "pex_x2" environment variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC8315ERDB boards features PCI-E x1 and Mini PCI-E x1 ports. Let's
support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for MPC83xx PCI-E controllers in Root Complex
mode.
The patch is based on Tony Li and Dave Liu work[1].
Though unlike the original patch, by default we don't register PCI-E
buses for use in U-Boot, we only configure the controllers for future
use in other OSes (Linux). This is done because we don't have enough
of spare BATs to map all the PCI-E regions.
To actually use PCI-E in U-Boot, users should explicitly define
CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES symbol in the board file. And
only then U-Boot will able to access PCI-E, but at the cost of disabled
address translation.
[1] http://lists.denx.de/pipermail/u-boot/2008-January/027630.html
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When running a system with 2 or more MPC8349EMDS boards in PCI agent mode,
the boards will lock up the PCI bus by scanning against each other.
The boards lock against each other by trying to access the PCI bus before
clearing their configuration lock bit. Both boards end up in a loop,
sending and receiving "Target Not Ready" messages forever.
When running in PCI agent mode, the scanning now takes place after the
boards have cleared their configuration lock bit.
Also, add a missing declaration to the mpc83xx.h header file, fixing a
build warning.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds esd's loadpci BSP command to CPCI4052 and
CPCI405AB board. This requires CONFIG_CMD_BSP and CONFIG_PRAM.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
- Move the TLB entry of PIXIS_BASE from TLB0 to TLB1[8], because in CAMP mode,
all the TLB0 entries will be invalidated after cpu1 brings up kernel, thus cpu0
can not access PIXIS_BASE anymore (any access will cause DataTLBError exception)
- Set CONFIG_SYS_DDR_TLB_START to 9 for MPC8572DS board.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately. This makes the code easier to read
and understand, and facilitates mapping changes going forward.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately. This makes the code easier to read
and understand, and facilitates mapping changes going forward.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Currently MPC85xx and MPC86xx boards just calculate the localbus frequency
and print it out, but don't save it.
This changes where its calculated and stored to be more consistent with the
CPU, CCB, TB, and DDR frequencies and the MPC83xx localbus clock.
The localbus frequency is added to sysinfo and calculated when sysinfo is
set up, in cpu/mpc8[56]xx/speed.c, the same as the other frequencies are.
get_clocks() copies the frequency into the global data, as the other
frequencies are, into a new field that is only enabled for MPC85xx and
MPC86xx.
checkcpu() in cpu/mpc8[56]xx/cpu.c will print out the local bus frequency
from sysinfo, like the other frequencies, instead of calculating it on the
spot.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
The values given for the PHY address were wrong, so the code
read no valid PHY ID, and fell through to the generic PHY
support, which would work on 1000M but would not auto negotiate
down to 100M or 10M.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These interfaces don't have usable connectors on the board, so don't
bother enumerating or configuring them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits
instead of four.
In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It
should be safe as the fifth bit was defined as reserved and set to 0.
Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
If we have addr map support enabled use the mapping functions to
implement virt_to_phys() and map_physmem().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
