Update the Kconfig entry to have the correct defaults for i.MX7
platforms, and move the existing large comment from imx7_spl.h to
doc/imx/common/imx7.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX6
platforms, and move the existing large comment from imx6_spl.h to
doc/imx/common/imx6.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of PowerPC platforms define this, for SPL. To move this to
Kconfig, it needs to be CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE, so use
CONFIG_IS_ENABLED() to check for usage. A number of layerscape
platforms bring this logic from PowerPC, but only need a small part of
it, for the fman driver. Remove their unused portion at least.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_INIT_MINIMAL
CONFIG_SPL_FLUSH_IMAGE
CONFIG_SPL_SKIP_RELOCATE
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only referenced in non-SPL_DM cases, of which there are
currently none. Remove this option and slightly re-organize the code is
there is now never an if/else at the start of spl_sata_load_image()
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a new device tree property "u-boot,version" in the chosen node to
pass the U-Boot version to the operating system.
This can be useful to implement a firmware upgrade procedure from the
operating system.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If the fitImage has some bad block in fit image area, the
offset must be recalulcated. This should be done always.
After implementing it in mxs now is possible to call the function
even for that platform.
Cc: Fabio Estevam <festevam@gmail.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Drop CONFIG_NEEDS_MANUAL_RELOC ifdefs in board_init_r() and use
IS_ENABLED() instead. Also, use the MANUAL_RELOC() macro to update the
initcall pointers.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
There is currently no support for PRE_CONSOLE_BUFFER in SPL, but if
and when that gets implemented, one would almost certainly want to use
a different address and/or size for the buffer (e.g., U-Boot proper
might specify an address in DRAM and a generous buffer, while SPL
would be much more constrained).
So a prerequisite for adding SPL_PRE_CONSOLE_BUFFER is to make the
code use SPL_-specific values. No functional change.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Booting of non-FIT images bypass our chain-of-trust boot flow,
these options should not be allowed when high security is set.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This matches what this support is called in the non-SPL case. The postfix
_SUPPORT is redundant as enabling Kconfig options implies support.
With this we can use CONFIG_IS_ENABLED() as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
UEFI:
* Fix build errors due to
- using sed with non-standard extension for regular expression
- target architecture not recognized for CROSS_COMPILE=armv7a-*
- CONFIG_EVENT not selected
* add sha384/512 on certificate revocation
Others:
* factor out the user input handling in bootmenu command
-----BEGIN PGP SIGNATURE-----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=Kdu1
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-07-rc3-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc3-2
UEFI:
* Fix build errors due to
- using sed with non-standard extension for regular expression
- target architecture not recognized for CROSS_COMPILE=armv7a-*
- CONFIG_EVENT not selected
* add sha384/512 on certificate revocation
Others:
* factor out the user input handling in bootmenu command
This commit moves the user input handling from cmd/bootmenu.c
to common/menu.c to reuse it from other modules.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This has been deprecated for over 10 years and everything now uses the
plain "phandle" property in preference. There's no need to set
linux,phandle when creating phandles for nodes that do not have one.
dtc changed the default to creating just phandle in version 1.4.5
released in September 2017 with the justification that the new style had
already been supported for 7 years by that point (see dtc commit 0016f8c
("dtc: change default phandles to ePAPR style instead of both")).
Signed-off-by: John Keeping <john@metanate.com>
menu_get_choice() needs to handle the case that menu item
is empty. In this case, menu_get_choice() returns -ENOENT.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
To make user aware of the menu entry selection, menu always
appears regardless of the number of entry.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Adjust test/py/tests/test_bootmenu.py
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add support for VPL, a new phase of U-Boot. This runs after TPL. It is
responsible for selecting which SPL binary to run, based on a
verified-boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature is not available in SPL unless common/ and lib/ are built.
Update the Kconfig to avoid build errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
efi_init_early() creates an event hook for block device probing.
It has to be called before any block device is probed.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When env support is disabled then usage of env_get() generates linker
errors. So do not compile env_get() when env support is disabled (for
example when disabled only in SPL).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To quote the author:
The bootflow feature provide a built-in way for U-Boot to automatically
boot an Operating System without custom scripting and other customisation.
This is called 'standard boot' since it provides a standard way for
U-Boot to boot a distro, without scripting.
It introduces the following concepts:
- bootdev - a device which can hold a distro
- bootmeth - a method to scan a bootdev to find bootflows (owned by
U-Boot)
- bootflow - a description of how to boot (owned by the distro)
This series provides an implementation of these, enabled to scan for
bootflows from MMC, USB and Ethernet. It supports the existing distro
boot as well as the EFI loader flow (bootefi/bootmgr). It works
similiarly to the existing script-based approach, but is native to
U-Boot.
With this we can boot on a Raspberry Pi 3 with just one command:
bootflow scan -lb
which means to scan, listing (-l) each bootflow and trying to boot each
one (-b). The final patch shows this.
With a standard way to identify boot devices, booting become easier. It
also should be possible to support U-Boot scripts, for backwards
compatibility only.
...
The design is described in these two documents:
https://drive.google.com/file/d/1ggW0KJpUOR__vBkj3l61L2dav4ZkNC12/view?usp=sharinghttps://drive.google.com/file/d/1kTrflO9vvGlKp-ZH_jlgb9TY3WYG6FF9/view?usp=sharing
Add a bootdev driver for USB host. It can use the distro boot mechanism to
locate a file, or any other available bootmeth.
Signed-off-by: Simon Glass <sjg@chromium.org>
In the next commit, CONFIG_EFI_SETUP_EARLY will become mandated
in order to support dynamic enumeration of efi_disk objects.
This can, however, be problematic particularly in case of file-based
variable storage (efi_variable.c, default).
Non-volatile variables are to be restored from EFI system partition
by efi_init_variables() in efi_init_obj_list(). When efi_init_obj_list()
is called in board_init_r(), we don't know yet what disk devices
we have since none of device probing commands (say, scsi rescan) has not
been executed at that stage.
So in this commit, a preparatory change is made; efi_init_obj_list() is
broken into the two functions;
* efi_init_early(), and
* new efi_init_obj_list()
Only efi_init_early() will be called in board_init_r(), which allows
us to execute any of device probing commands, either though "preboot"
variable or normal command line, before calling efi_init_obj_list() which
is to be invoked at the first execution of an efi-related command
(or at efi_launch_capsules()) as used to be.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This was implemented in order to get dual-slot bootloader
partitions on the BeagleBone Black, whose MLO boots from
the first bootable partition: MLO chainloads u-boot in the
same way.
Signed-off-by: Jérôme Carretero <cJ-uboot@zougloub.eu>
Reviewed-by: Tom Rini <trini@konsulko.com>
This annotates malloc and friends so that valgrind can track the heap. To
do this, we need to follow a few rules:
* Call VALGRIND_MALLOCLIKE_BLOCK whenever we malloc something
* Call VALGRIND_FREELIKE_BLOCK whenever we free something (generally after
we have done our bookkeeping)
* Call VALGRIND_RESIZEINPLACE_BLOCK whenever we change the size of an
allocation. We don't record the original request size of a block, and
neither does valgrind. For this reason, we pretend that the old size of
the allocation was for 0 bytes. This marks the whole allocaton as
undefined, so in order to mark all bits correctly, we must make the whole
new allocation defined with VALGRIND_MAKE_MEM_DEFINED. This may cause us
to miss some invalid reads, but there is no way to detect these without
recording the original size of the allocation.
In addition to the above, dlmalloc itself tends to make a lot of accesses
which we know are safe, but which would be unsafe outside of dlmalloc. For
this reason, we provide a suppression file which ignores errors ocurring in
dlmalloc.c
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation:
* Describe how enable DM_SERIAL for a board
UEFI
* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
-----BEGIN PGP SIGNATURE-----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=SxkC
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc1
Documentation:
* Describe how enable DM_SERIAL for a board
UEFI
* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
Every time a usb bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the CONFIG macros to conditionally build the GPIO hogging support in
either the SPL or U-Boot, or both, depending on the configuration. Also
call the GPIO hog probe function in the common SPL board initialization
as an equivalent to adding it to the U-Boot init sequence functions.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This doesn't really make much sense in the documentation. Add a code
comment instead.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Platforms can overwrite the weak definition of spl_mmc_boot_mode() to
determine where to load U-Boot proper from.
For most of them this is a trivial decision based on Kconfig variables,
but it might be desirable the probe the actual device to answer this
question.
Pass the pointer to the mmc struct to that function, so implementations
can make use of that.
Compile-tested for all users changed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ley Foon Tan <ley.foon.tan@inte.com> (for SoCFPGA)
Acked-by: Lokesh Vutla <lokeshvutla@ti.com> (for OMAP and K3)
Reviewed-by: Simon Glass <sjg@chromium.org>
When u-boot is used as a chain-loaded bootloader (replacing OS kernel),
previous bootloader leaves data in RAM, that can be reused.
For example, on recent arm linux system, when chainloading u-boot,
there are initramfs and fdt in RAM prepared for OS booting. Initramfs
may be modified to store u-boot's payload, thus providing the ability to
use chainloaded u-boot to boot OS without any storage support.
Two config options added:
- SAVE_PREV_BL_INITRAMFS_START_ADDR
saves initramfs start address to 'prevbl_initrd_start_addr' environment
variable
- SAVE_PREV_BL_FDT_ADDR
saves fdt address to 'prevbl_fdt_addr' environment variable
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
This adds a boot method for loading the next stage from the host. It is
mostly modeled off of spl_load_image_ext. I am not really sure why/how
spl_load_image_fat uses three different methods to load the image, but
the simple case seems to work OK for now.
To control the presence of this boot method, we add a config symbol.
While we're at it, we update the original semihosting config symbol.
I think semihosting has some advantages of other forms of JTAG boot.
Common other ways to boot from JTAG include:
- Implementing DDR initialization through JTAG (typically with dozens of
lines of TCL) and then loading U-Boot. The DDR initialization
typically uses hard-coded register writes, and is not easily adapted
to different boards. BOOT_DEVICE_SMH allows booting with SPL,
leveraging U-Boot's existing DDR initialization code. This is the
method used by NXP's CodeWarrior IDE on Layerscape processors (see
AN12270).
- Loading a bootloader into SDRAM, waiting for it to initialize DDR, and
then loading U-Boot. This is tricky, because the debugger must stop the
boot after the bootloader has completed its work. Trying to load
U-Boot too early can cause failure to boot. This is the method used by
Xilinx with its Zynq(MP) processors.
- Loading SPL with BOOT_DEVICE_RAM and breaking before SPL loads the
image to load U-Boot at the appropriate place. This can be a bit
tricky, because the load address is dependent on the header size. An
elf with symbols must also be used in order to stop at the appropriate
point. BOOT_DEVICE_SMH can be viewed as an extension of this process,
where SPL automatically stops and tells the host where to place the
image.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Add the support of image pre load in spl or tpl
when loading an image from ram.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This is not defined by any board. Even sandbox doesn't actually use
it since it has migrated to DM_VIDEO.
Drop this option. Remove the dead code also, for completeness, even
though the whole lcd.c file will be dropped soon.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
The non-driver model video support was removed two years ago. Drop this
driver, which is only used by nokia_rx51.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix the help which should refer to TPL, not SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Suggested-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Generate events when devices are probed or removed, allowing hooks
to be added for these situations.
This is controlled by the DM_EVENT config option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to create and dispatch events without needing to allocate
memory. Also add a way to 'spy' on events, thus allowing 'hooks' to be
created.
Use a linker list for static events, which we can use to replace functions
like arch_cpu_init_f(). Allow an EVENT_DEBUG option which makes it
easier to see what is going on at runtime, but uses more code space.
Dynamic events allow the creation of a spy at runtime. This is not always
necessary, but can be enabled with EVENT_DYNAMIC if needed.
A 'test' event is the only option for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
When CONFIG_SPL_FIT is enabled we do not access U-Boot directly in
the image, since it is embedded in a FIT which is parsed at runtime.
Provide a CONFIG option to drop the symbols in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
These symbols are incorrect, meaning that binman cannot find the
associated entry. This leads to errors like:
binman: Section '/binman/simple-bin': Symbol '_binman_spl_prop_size'
in entry '/binman/simple-bin/u-boot-spl/u-boot-spl-nodtb':
Entry 'spl' not found in list (mkimage,u-boot-spl-nodtb,
u-boot-spl-bss-pad,u-boot-spl-dtb,u-boot-spl,u-boot-img,main-section)
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace %zx by %lx and cast size_t to ulong.
U-Boot currently prints garbage debug output:
size=x, ptr=18, limit=18: 4002a000
With this change it prints correct debug data:
size=18, ptr=18, limit=2000: 4002a000
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Listing MTD partitions directly in the flash mode has been deprecated
for a while for kernel Device Trees. Look for a node "partitions" in the
found flash nodes and use it instead of the flash node itself for the
partition list when it exists, so Device Trees following the current
best practices can be fixed up.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Using the XHCI driver, the function `usb_kbd_poll_for_event` takes
30-40ms to run. The exact time is dependent on the polling interval the
keyboard requests in its descriptor, and likely cannot be significantly
reduced without major rework to the XHCI driver.
The U-Boot EFI console service sets a timer to poll the keyboard every 5
microseconds, and this timer is checked every time a block is read off
disk. The net effect is that, on my system, loading a ~40MiB kernel and
initrd takes about 62 seconds with a slower keyboard and 53 seconds
with a faster one, with the vast majority of the time spent polling the
keyboard.
To solve this problem, this patch adds a 20ms delay between consecutive
calls to `usb_kbd_poll_for_event`. This is sufficient to reduce the
total loading time to under half a second for both keyboards, and does
not impact the perceived keystroke latency.
Signed-off-by: Thomas Watson <twatson52@icloud.com>
Use the new IF_ENABLED_INT() feature to avoid needing our own inline
function to handle this case. Tidy up the logic to ensure that the value
is only used when present. Update the 'expected' comment also.
Signed-off-by: Simon Glass <sjg@chromium.org>
ymodem_read_fit() driver will end copying up to BUF_SIZE boundary even
when requested size of copy operation is less than that.
For example, if offset = 0, size = 1440B, ymodem_read_fit() ends up
copying 2KB from offset = 0, to destination buffer addr
This causes data corruption when malloc'd buffer is passed during UART
boot since commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer
for loading images")
With this, UART boot works again on K3 (AM654, J7, AM64) family of
devices.
Fixes: 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for loading images")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Currently the names MMC1, MMC2 and MMC2_2 are output in the SPL. To
achieve more userbility here the name of the boot source can be returned.
E.g. for "MMC1" -> "eMMC" or "MMC2" -> "SD card".
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmHyEeYRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYYlgf8C7tQVklXz9ZHhxVrFaPHWwgmBzEZJSrc
7SWhDX9yBrAYBUk8Q4OMnJz6nXW8Rz5Td9GfBNWcJag1HjJqno4BxkqwGk2tshgj
GIY0D1cGfKJzB4E6/rK/ETwmX4KVUyEf7S2IdJ0oydkn9t7OwDkUX5WtGXo70E7q
ZJGYlX5NQCVBRAF9NYDuyVFljrPzAiyT58VCtXY3q63C7PmRYvag8r56ug+8lkk3
9EbOTcwETqq9SbT1vucyBxwbUmoKhb2BF32jEcIhozowIM3GNsSpkdzQCUnylqfa
LYI/p0oVTKLfFRBRvQjLgdB/OQP8MLkby8A++Db2OW49mBXhn/5JWA==
=PdpE
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jan22' of https://source.denx.de/u-boot/custodians/u-boot-dm
acpi refactoring to allow non-x86 use
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
Add support for CDC ACM using the new UDC and gadget API. This protocol
can be used for serial over USB data transfer and is widely supported
by various OS (GNU/Linux, MS-Windows, OSX...). The usual purpose of
such link is to access device debug console and can be useful for
products not exposing regular UART to the user.
A default stdio device named 'usbacm' is created, and can be used
to redirect console to USB link over CDC ACM:
> setenv stdin usbacm; setenv stdout usbacm
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
At present we rely on the key blob being in the global_data fdt_blob
pointer. This is true in U-Boot but not with tools. For clarity, pass the
parameter around.
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace CONFIG_SYS_MAX_FLASH_BANKS by CFI_FLASH_BANKS to prepare
Kconfig migration and avoid to redefine CONFIG_SYS_MAX_FLASH_BANKS
in cfi_flash.h.
After this patch CONFIG_SYS_MAX_FLASH_BANKS should be never used in
the cfi code: use CFI_MAX_FLASH_BANKS for struct size or CFI_FLASH_BANKS
for number of CFI banks which can be dynamic.
This patch modify all the files which include mtd/cfi_flash.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Commit 9baab60b80 ("SPL: Add support for parsing board / BootROM specific
image types") added support for loading board specific image types.
This commit adds support for a new weak function spl_parse_board_header()
which is called after loading boot image. Board may implement this function
for checking if loaded board specific image is valid.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop the remaining ifdefs around header includes, to fix an old TODO.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Not all architectures define <asm/gpio.h> and even on those that do, the
header cannot be included for all boards without causing various build
failures.
Since common/board_r.c only needs gpio_hog_probe_all() declaration, include
<asm-generic/gpio.h> and drop the associated ifdef.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Add a return value to init_addr_map and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Add a return value to kgdb_init and use it directly in the post-relocation
init sequence, rather than using a wrapper stub. Also, move the "KGDB"
print message inside kgdb_init().
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Commit 98f705c9ce ("powerpc: remove 4xx support") removed (in 2017) the
last code that made use of bedbug debugger support. Since there aren't
any boards left that define either CONFIG_CMD_BEDBUG or a real
bedbug_init(), drop this feature from u-boot.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Factor out armv7m fragment to spl_perform_fixups(), which is an arch/board
specific function designed for this purpose.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
This implementation is intended to be copied to other projects and
modified, to as to foster a standard means of communcating runtime
information between firmware projects.
The GPL-2 license is too restrictive for some projects, e.g. those
intended as reference implementations rather than designed for
collaborative open-source development.
Update the license to make this easier to share.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we do support allocating the bloblist but the Kconfig is a bit
strange, since we still have to specify an address in that case. Partly
this is because it is a pain to have CONFIG options that disappears when
its dependency is enabled. It means that we must have #ifdefs in the code,
either in the C code or header file.
Make use of IF_ENABLED_INT() and its friend to solve that problem, so we
can separate out the location of bloblist into a choice. Put the address
and size into variables so we can log the result.
Add the options for SPL as well, so we can use CONFIG_IS_ENABLED().
Signed-off-by: Simon Glass <sjg@chromium.org>
We typically refer to the different U-Boot builds that a board runs
through as phases. This avoids confusion with the word 'stage' which is
used with bootstage, for example. Fix up some bloblist Kconfig help
which uses the wrong term.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if someone adds a tag in the middle of the list it works well
enough within a U-Boot build. But if these tags are used in another
project, or with an older version of SPL, the numbers make become
inconsistent.
Use explicit tag numbers that never change, to resolve this problem.
Allocate areas for existing U-Boot tags and set up an area for use by
projects and vendors, as well as for private use. Keep tags above
0x10000 unallocated for now.
Update bloblist_tag_name() and the tests to work with this new setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
The EC event log tag is no-longer used. The vboot handoff is now handled
by the vboot context instead.
Drop these unused tags.
Signed-off-by: Simon Glass <sjg@chromium.org>
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
-----BEGIN PGP SIGNATURE-----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=YdSB
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request of efi-next
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
Since EFI does not relocate and uses the same global_data pointer
throughout the board-init process, drop this unnecessary setup, to avoid
a hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VIDEO_LOGO
Note that this option depends on CONFIG_DM_VIDEO now, since cfb_console is
deprecated. The only relevant code is now in splash.c
Drop the check for DM_VIDEO in that file.
Signed-off-by: Simon Glass <sjg@chromium.org>
The video driver uses this for debugging, but if used before relocation it
crashes at present. Avoid trying to output debugging before the console is
ready.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running, if the devicetree failed to come from the expected source,
show a warning, e.g:
U-Boot ...
DRAM: 128 MiB
Core: 42 devices, 11 uclasses, devicetree: separate
Warning: Unexpected devicetree source (not from a prior stage)
Warning: U-Boot may not function properly
Flash: 64 MiB
...
These warnings should only appear if the board config has been changed, or
the prior stage is broken.
Signed-off-by: Simon Glass <sjg@chromium.org>
It can be confusing to figure out where the devicetree came from. It seems
important enough to warrant a message during boot. Add information about
the number of devices and uclasses too since it is helpful to have some
idea what is going on with driver model.
Report the devicetree source in bdinfo too.
This looks something like this, with > marking the new line.
U-Boot 2021.10-00190 (Oct 30 2021 - 09:01:29 -0600)
DRAM: 128 MiB
> Core: 42 devices, 11 uclasses, devicetree: passage
Flash: 64 MiB
Signed-off-by: Simon Glass <sjg@chromium.org>
Move Turris MOX specific remove_disabled_nodes() to fdt_support with
name fdt_delete_disabled_nodes(), so that others can potentially use it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add functions
fdt_node_offset_by_pathf(),
fdt_create_phandle_by_pathf(),
fdt_set_status_by_pathf()
to get node offset, get/create node phandle and set status for node
given by path/alias formatted with sprintf.
Add functions
fdt_create_phandle_by_compatible(),
fdt_set_status_by_compatible()
to get/create node phandle and set status for first node given by
compatible.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This function does not necessarily create a new phandle. If a phandle
exists, no new phandle is created.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit f0921f5098 ("fdt: Sync up to the latest libfdt") introduced
fdt_generate_phandle() in libfdt, making fdt_alloc_phandle() obsolete in
fdt_support.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: "hui.song" <hui.song_1@nxp.com>
Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Typically the bloblist is positioned at a fixed address in memory until
relocation. This is convenient when it is set up in SPL or before
relocation.
But for EFI we want to set it up only when U-Boot proper is running. Add
a way to allocate it using malloc() and update the documentation to cover
this aspect of bloblist.
Note there are no tests of this feature at present, nor any direct testing
of bloblist_init().
This can be added, e.g. by making this option controllable at runtime.
Signed-off-by: Simon Glass <sjg@chromium.org>
When, for various reasons, a bad FIT image is used where a loadable
image is marked as 0 length, attempt is made for a 0 length allocation and
read of 0 byte read operation.
Instead provide warning in log and skip attempting to do such a load.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Add a new function to activate an existing simple frame buffer node
and add the associated reserved memory, with no-map properties.
This device tree update is only done when the video device is active
and the video buffer is used.
This patch uses '#if CONFIG_IS_ENABLED(DM_VIDEO)' because
gd->video_bottom and gd->video_top are only defined when CONFIG_DM_VIDEO
is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the function named lcd_dt_simplefb* to fdt_simplefb* to be aligned
with the associated file name fdt_simplefb.h/fdt_simplefb.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Rename the file lcd_simplefb.c to fdt_simplefb.c to be aligned
with the configuration name and with the associated include file
./include/fdt_simplefb.h
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the following to Kconfig:
CONFIG_LCD_DT_SIMPLEFB
This patch also renames this config to CONFIG_FDT_SIMPLEFB as the code in
common/lcd_simplefb.c support CONFIG_LCD and CONFIG_VIDEO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Before relocation there is generally not as much available memory and not
that much console output. At present the console-output buffer is the same
side before and after relocation. Add a separate Kconfig option to remove
this limitation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Even if U-Boot has relocation disabled via GD_FLG_SKIP_RELOC , the
relocated stage of U-Boot still picks GD from new_gd location. The
U-Boot itself is not relocated, but GD might be, so copy the GD to
new GD location even if relocation is disabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Peng Fan <peng.fan@oss.nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The last board that used to set CONFIG_LYNXKDI has been removed in
commit 242836a893 ("powerpc: ppc4xx: remove pcs440ep support"),
doc/README.lynxkdi only talks about a MPC8260 board being supported,
and the mpc8260 support has been removed four years ago in commit
2eb48ff7a2 ("powerpc, 8260: remove support for mpc8260") already,
and common/lynxkdi.c only consists of an "#error" statement these
days, so it seems like the LYNX KDI code is dead code nowadays.
Let's remove it now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Quite a lot of the code in common/relates to booting and images. Before
adding more it seems like a good time to move the code into its own
directory.
Most files with 'boot' or 'image' in them are moved, except:
- autoboot.c which relates to U-Boot automatically running a script
- bootstage.c which relates to U-Boot timing
Drop the removal of boot* files from the output directory, since this
interfers with the symlinks created by tools and there does not appear
to be any such file from my brief testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
This statement has an unmatched parentheses, fix it.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When building a system that has both TPL and SPL_OS_BOOT, code which
tests for CONFIG_SPL_OS_BOOT will be built and enabled in TPL, which is
not correct. While there is no CONFIG_TPL_OS_BOOT symbol at this time
(and likely will not ever be) we can use CONFIG_IS_ENABLED(OS_BOOT) in
these common paths to ensure we only compile these parts in the SPL
case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Allow usage of the bootstage facilities in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The data blob apparently does not need to be modified through the fit
field of the image_sign_info struct so make it point to const to avoid
the need to cast away constness in functions that assign a pointer to
const data to the field.
fit_image_setup_verify already had to cast away constness as it assigned
a const void * argument to the field. The cast can now be removed.
Signed-off-by: Hannu Lounento <hannu.lounento@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The padding pss is only supported on u-boot and tools since
commit 2bbed3ff8c ("image: Use Kconfig to enable FIT_RSASSA_PSS on host")
This commit adds the config SPL_FIT_RSASSA_PSS to support
the padding pss in the SPL.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure to (if applicable) flush the D-cache, invalidate I-cache,
and disable MMU and caches before jumping to OPTEE.
This fixes the SDP->SPL->OPTEE boot flow on iMX6Q and most likely on
some other ARM SoCs.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
After DM_VIDEO conversion the 'vidconsole' is the correct name
for the frame buffer console. 'video' will not work, so update
the description of the config option.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
At present U-Boot has a header file called lz4.h for its own use. If the
host has its own lz4 header file installed (e.g. from the 'liblz4-dev'
package) then host builds will use that instead.
Move the U-Boot file into its own directory, as is done with various
other headers with the same problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is far too long. Before trying to remove #ifdefs, split out
the code that deals with selecting the FDT into a separate function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use boolean variables to deal with the strange #ifdef logic of this
function, so we can remove the #ifdefs.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is far too long. Before trying to remove #ifdefs, split out
the code that deals with selecting the ramdisk into a separate function.
Leave the code indented as it was for easier review. The next patch cleans
this up along with checkpatch violations.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is only used in one place and does not need to use the
preprocessor. Move it to the C file and convert it to a normal function.
Drop fit_unsupported() since it is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
We can use the new host_build() function for this, so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough and the board code is now in a separate file. Update the only place
where this is used and drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for CRC32. With this we can use CONFIG_IS_ENABLED(CRC32)
directly in the host build, so drop the unnecessary indirection.
Add a few more conditions to SPL_CRC32 to avoid build failures as well as
TPL_CRC32. Also update hash.c to make crc32 optional and to actually take
notice of SPL_CRC32.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for OF_LIBFDT. With this we can use
CONFIG_IS_ENABLED(OF_LIBFDT) directly in the tools build, so drop the
unnecessary indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Make use of the host Kconfig for FIT. With this we can use
CONFIG_IS_ENABLED(FIT) directly in the host build, so drop the unnecessary
indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We can use the __maybe_unused attribute to avoid some of the #ifdefs in
this file. Update the functions accordingly.
Note: The actual hashing interface is still a mess, with four separate
combinations and lots of #ifdefs. This should really use a driver
approach, e.g. as is done with partition drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
At present when building host tools, we force CONFIG_SHAxxx to be enabled
regardless of the board Kconfig setting. This is done in the image.h
header file.
For SPL we currently just assume the algorithm is desired if U-Boot proper
enables it.
Clean this up by adding new Kconfig options to enable hashing on the host,
relying on CONFIG_IS_ENABLED() to deal with the different builds.
Add new SPL Kconfigs for hardware-accelerated hashing, to maintain the
current settings.
This allows us to drop the image.h code and the I_WANT_MD5 hack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
In preparation for enabling CONFIG_IS_ENABLED() on the host build, add
some options to enable the various FIT options expected in these tools.
This will ensure that the code builds correctly when CONFIG_TOOLS_xxx
is distinct from CONFIG_xxx.
Drop some #ifdefs which are immediately unnecessary (many more are in
later patches).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
With the new TOOLS_LIBCRYPTO and some other changes, it seems that we are
heading towards calling this a tools build rather than a host build,
although of course it does happen on the host.
I cannot think of anything built by the host which cannot be described as
a tool, so rename this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a macro to handle manually relocating a pointer. Update the iamge code
to use this to avoid needing #ifdefs.
This also fixes a bug where the 'done' flag was not set.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than adding an #ifdef and open-coding this calculation, add a
helper function to handle it. Use this in the image code.
Signed-off-by: Simon Glass <sjg@chromium.org>
To avoid having #ifdefs in a few functions which are completely different
in the board and host code, create a new image-host.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
To avoid a large #ifdef in the image.c file, move the affected code into
a separate file.
Avoid any style fix-ups for easier review. Those are in the next patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust this function so that preprocessor macros are not needed. With
this, the host build uses more of the same header files as the target
build.
Rather than definining CONFIG_SYS_MALLOC_LEN, add a CONSERVE_MEMORY
define, since that is the purpose of the value.
This appears to have no impact on code size from a spot check of a few
boards (snow, firefly-rk3288, boston32r2el, m53menlo).
Signed-off-by: Simon Glass <sjg@chromium.org>
The zstd implementation prints the error in image_decomp() which is
incorrect and does not match other algorithms. Drop this and let the
caller report the error.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function is full of preprocessor macros. Adjust it to
check for an unsupported algorithm after the switch(). This will allow
us to drop the macros.
Fix up the return-value path and an extra blank line while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing zstd API requires the same sequence of calls to perform its
task. Create a helper for U-Boot, to avoid code duplication, as is done
with other compression algorithms. Make use of of this from the image
code.
Note that the zstd code lacks a test in test/compression.c and this should
be added by the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
cherry-picked from NXP code:
719d665a87c6: ("MLK-20467 imx8m: Fix issue for booting signed image through uuu")
which fixes secure boot on imx8m based boards. Problem was
that FIT header and so IVT header too, was loaded to
memallocated address. So the ivt header address coded
in IVT itself does not fit with the real position.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com>
add hook function spl_load_simple_fit_fix_load()
which is called after fit image header is loaded.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
bootm_low is used as a base address is used to allocate space for the
FDT blob, initrd, cmdline, etc. when booting Linux. Set the default
value for RISC-V to the start of the first DRAM bank, so platforms can
get their DRAM layout from the device tree, and do not need to define
CONFIG_SYS_SDRAM_BASE.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The configuration CONFIG_OPTEE is defined 2 times:
1- in lib/optee/Kconfig for support of OPTEE images loaded by bootm command
2- in drivers/tee/optee/Kconfig for support of OP-TEE driver.
It is abnormal to have the same CONFIG define for 2 purpose;
and it is difficult to managed correctly their dependencies.
Moreover CONFIG_SPL_OPTEE is defined in common/spl/Kconfig
to manage OPTEE image load in SPL.
This definition causes an issue with the macro CONFIG_IS_ENABLED(OPTEE)
to test the availability of the OP-TEE driver.
This patch cleans the configuration dependency with:
- CONFIG_OPTEE_IMAGE (renamed) => support of OP-TEE image in U-Boot
- CONFIG_SPL_OPTEE_IMAGE (renamed) => support of OP-TEE image in SPL
- CONFIG_OPTEE (same) => support of OP-TEE driver in U-Boot
- CONFIG_OPTEE_LIB (new) => support of OP-TEE library
After this patch, the macro have the correct behavior:
- CONFIG_IS_ENABLED(OPTEE_IMAGE) => Load of OP-TEE image is supported
- CONFIG_IS_ENABLED(OPTEE) => OP-TEE driver is supported
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
We have individual SOC symbols for each keystone 2 platform. Use the
existing CONFIG_ARCH_KEYSTONE rather than CONFIG_SOC_KEYSTONE to
encompass all of the keystone families.
Signed-off-by: Tom Rini <trini@konsulko.com>
The current API is outdated as it requires a devicetree pointer.
Move these functions to use the ofnode API and update this globally. Add
some tests while we are here.
Correct the call in exynos_dsim_config_parse_dt() which is obviously
wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Header file version.h does not use anything from timestamp.h. Including of
timestamp.h has side effect which cause recompiling object file at every
make run because timestamp.h changes at every run.
So remove timestamp.h from version.h and include timestamp.h in files
which needs it.
This change reduce recompilation time of final U-Boot binary when U-Boot
source files were not changed as less source files needs to be recompiled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add in lib/acpi/acpi_table.c and test/dm/acpi.c, rework a few others]
Signed-off-by: Tom Rini <trini@konsulko.com>
More C files do not use compile time timestamp macros and do not have to be
recompiled every time when SOURCE_DATE_EPOCH changes.
This patch moves version_string[] from version.h to version_string.h and
updates other C files which only needs version_string[] string to include
version_string.h instead of version.h. After applying this patch these
files are not recompiled every time when SOURCE_DATE_EPOCH changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The hash algorithm selection was streamlined in commit 92055e138f
("image: Drop if/elseif hash selection in calculate_hash()"). Said
commit kept the call to cpu_to_uimage() to convert the CRC to big
endian format.
This would have been correct when calling crc32_wd(). However, the
->hash_func_ws member of crc32 points to crc32_wd_buf(), which already
converts the CRC to big endian. On a little endian host, doing both
conversions results in a little-endian CRC. This is incorrect.
To remedy this, simply drop the call to cpu_to_uimage(), thus only
doing the byte-order conversion once.
Fixes: 92055e138f ("image: Drop if/elseif hash selection in
calculate_hash()")
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We are not guaranteed to have the padding_pkcs_15_verify symbol since
commit 92c960bc1d ("lib: rsa: Remove #ifdefs from rsa.h"), and
commit 61416fe9df ("Kconfig: FIT_SIGNATURE should not select RSA_VERIFY")
The padding_algos only make sense with RSA verification, which can now
be disabled in lieu of ECDSA. In fact this will lead to build failures
because of the missing symbol mentioned earlier.
To resolve this, move the padding_algos to a linker list, with
declarations moved to rsa_verify.c. This is consistent with commit
6909edb4ce ("image: rsa: Move verification algorithm to a linker list")
One could argue that the added #ifdef USE_HOSTCC is ugly, and should
be hidden within the U_BOOT_PADDING_ALGO() macro. However, this would
be inconsistent with the "cryptos" list. This logic for was not
previously explored:
Without knowledge of the U_BOOT_PADDING_ALGO() macro, its use is
similar to something being declared. However, should #ifndef
USE_HOSTCC be part of the macro, it would not be obvious that it
behaves differently on host code and target code. Having the #ifndef
outside the macro makes this obvious.
Also, the #ifdef is not always necessary. For example ecda-verify
makes use of U_BOOT_CRYPTO_ALGO() without any accompanying #ifdefs.
The fundamental issue is a lack of separation of host and target code
in rsa_verify. Therefore, the declaration of a padding algo with the
external #ifdef is more readable and consistent.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
calculate_hash() would try to select the appropriate hashing function
by a if/elseif contruct. But that is exactly why hash_lookup_algo()
exists, so use it instead.
This does mean that we now have to 'select HASH' to make sure we get
the hash_lookup_algo() symbol. However, the change makes sense because
even basic FITs will have to deal with "hash" nodes.
My only concern is that the 'select SPL_HASH' might cause some
platform to grow above its SPL size allowance
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Make FSL_CAAM be implied only on ARM && SPL]
Signed-off-by: Tom Rini <trini@konsulko.com>
MD5 is being called directly in some places, but it is not available
via hash_lookup_algo("md5"). This is inconsistent with other hasing
routines. To resolve this, add an "md5" entry to hash_algos[].
The #ifdef clause looks funnier than those for other entries. This is
because both MD5 and SPL_MD5 configs exist, whereas the other hashes
do not have "SPL_" entries. The long term plan is to get rid of the
ifdefs, so those should not be expected to survive much longer.
The md5 entry does not have .hash_init/update/finish members. That's
okay because hash_progressive_lookup_algo() will catch that, and
return -EPROTONOSUPPORT, while hash_lookup_algo() will return the
correct pointer.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Use CONFIG_IS_ENABLED not IS_ENABLED for MD5 check]
Signed-off-by: Tom Rini <trini@konsulko.com>
All of these configs exist. Stick to using CONFIG_[ST]PL_HASH, and drop all
references to CONFIG_[ST]PL_HASH_SUPPORT. This means we need for
CHAIN_OF_TRUST to select SPL_HASH now.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Add TPL case, fix CHAIN_OF_TRUST, other tweaks]
Signed-off-by: Tom Rini <trini@konsulko.com>
Originally CONFIG_FIT_SHAxxx enabled specific SHA algos for and only
for hash_calculate() in common/image-fit.c. However, since commit
14f061dcb1 ("image: Drop IMAGE_ENABLE_SHAxxx"),
the correct selector was changed to CONFIG_SHAxxx.
The extra "_FIT_" variants are neither used, nor needed. Remove them.
One defconfig disables FIT_SHA256, which is now changed to 'SHA256'.
CMD_MVEBU_BUBT needs to select select SHA256 to avoid undefined
references to "sha256_*()". bubt.c needs sha256, so this selection is
correct. It is not clear why this problem did not manifest before.
Note that SHA selection in SPL is broken for this exact reason. There
is no corresponding SPL_SHAxxx. Fixing this is is beyond the scope of
this change.
Also note that we make CONFIG_FIT now imply SHA256, to make up for
FIT_SHA256 previously being a default y option.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Add imply SHA256 to FIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
The enable_caches is a generic hook for architecture-implemented, we
leverage this function to enable caches for RISC-V
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The code under drivers/net is related to ethernet networking drivers, in
some fashion or another. Drop these from the top-level Makefile and
also move the phy rule into drivers/net/Makefile which is where it
belongs. Make the new rule for drivers/net check for the build-stage
relevant ETH symbol.
Fix up some Kconfig dependencies while we're here to mirror how the
Makefile logic now works.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Introduce ETH, Kconfig dependency changes, am43xx fix]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the power/ rules into drivers/power to avoid clutter in the Makefile
and drivers/Makefile files.
We must select SPL_POWER if SPL_POWER_DOMAIN is used, since the two are
currently independent and boards do not necessarily enable SPL_POWER.
Add a TPL_POWER as well, as that is used by one board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Oddly there is already an SPL_CACHE option. Drop it in favour of this one.
Drop the special SPL Makefile rule which is now superfluous.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently it is possible to cancel loadx and loady commands by pressing
CTRL+X (CAN character) at least 3 times quickly.
All other U-Boot commands, including loadb and loads can be cancelled by
CTRL+C. So allow it also in xyz-modem code used by loadx and loady
commands. Implement it by handling CTRL+C (ETX character) in the same way
as CTRL+X (CAN character).
Due to how x/y-modem protocol works, it is required to press
CTRL+C or CTRL+X at least 3 times quickly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In x-modem protocol EOF is not an error state at the end of file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Variable xyz.len is set to -1 on error. At the end xyzModem_stream_read()
function calls memcpy() with length from variable xyz.len. If this variable
is set to -1 then value passed to memcpy is casted to unsigned value, which
means to copy whole address space. Which then cause U-Boot crash. E.g. on
arm64 it cause CPU crash: "Synchronous Abort" handler, esr 0x96000006
Fix this issue by checking that value stored in xyz.len is valid prior
trying to use it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Calculate hash using DM driver if supported.
For backward compatibility, the call to legacy
hash functions is reserved.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Signed-off-by: Tom Rini <trini@konsulko.com>
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYSilpgAKCRDKSWXLKUoM
Id2JAJ9jY19JiEpOd3vuRCT5CE/pzX4yDACeP8DiXDzSi5tLHwDWUCBobUTze2s=
=5lnj
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.10-rc3
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
Add kernel-doc description for fdt_fixup_memory_banks() because it is
implemented in one specific way and this information should be available
for others to decide if their SoC conforms to it.
If you don't want U-Boot to update your memory DT layout please disable
CONFIG_ARCH_FIXUP_FDT_MEMORY.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FIT signatures can now be implemented with ECDSA. The assumption that
all FIT images are signed with RSA is no longer valid. Thus, instead
of 'select'ing RSA, only 'imply' it. This doesn't change the defaults,
but allows one to explicitly disable RSA support.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The "-E" option to mkimage generates a FIT with external data using the
data-size and data-offset properties which must both be ignored when
verifying a signature.
Add "data-offset" to the list of excluded properties for signature
verification; since the line is now too long, re-format the list to
one-per-line and make it static since the data is constant.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function seems to assume that the chr[] variable contains zeros at
the start, which is not always true. Use strlcpy() to be safe.
Signed-off-by: Simon Glass <sjg@chromium.org>
The autoboot tests are a recent addition to U-Boot, providing much-needed
coverage in this area.
A side effect of the keyed autoboot test is that this feature is enabled
in sandbox always. This changes the autoboot prompt and confuses the
pytests. Some tests become slower, for example the vboot tests take about
27s now instead of 3s.
We don't actually need this feature enabled to be able to run the tests.
Add a switch to allow sandbox to turn it on and off as needed. Use this
in the one test that needs it.
Add a command-line flag in case this is desired in normal use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 25c8b9f298 ("test: add first autoboot unit tests")
Reviewed-by: Steffen Jaeckel <jaeckel-floss@eyet-services.de>
Now that proper load and execution addresses are set in v1 kwbimage we
can use it for loading and booting U-Boot proper.
Use the new spl_parse_board_header() function to implement parsing the
kwbimage v1 header. Use information from this header to locate offset and
size of the U-Boot proper binary, instead of using the legacy U-Boot
header which is prepended to the U-Boot proper binary stored at fixed
offset. This has the advantage that we do not need to relay on legacy
U-Boot header anymore and therefore U-Boot proper binary can be stored at
any offset, as is the case when loading & booting U-Boot proper by
BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL
code anymore.
Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case
BootROM is used for loading and executing U-Boot proper. This reduces the
size of U-Boot's SPL image. By default these config options are enabled
and so BootROM loading is not used. In some cases BootROM reads from SPI
NOR at lower speed than U-Boot SPL. So people can decide whether they
want to have smaller SPL binary at the cost of slower boot.
Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO,
CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT,
CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and
CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply"
(which can be selectivelly turned off and causes booting via BootROM).
Options CONFIG_SYS_SPI_U_BOOT_OFFS,
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to
zero as they define the location where kwbimage header starts. It is the
location where BootROM expects start of the kwbimage from which it reads,
parses and executes SPL part. The same applies to option
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one.
Update all config files to set correct values of these options and set
CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot
proper starts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Platform specific BootROM may use its own image type for loading SPL or
U-Boot proper. In some cases it makes sense to not use BootROM supplied
code for booting U-Boot proper but rather to use U-Boot SPL for this,
e.g. when U-Boot SPL can load U-Boot proper faster than BootROM. In this
case it is required for platform board code to parse and load U-Boot in
BootROM specific image type.
This change adds support for parsing platform / board / BootROM specific
image types via weak function spl_parse_board_header() which is called
before marking boot image as a raw.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Some image types (e.g. kwbimage v1) store the offset to SPL binary and
offset to U-Boot proper binary in their headers. To avoid reading SPL
binary when loading U-Boot proper, add support for specifying offset in
struct spl_image_info, which defines the offset from the beginning of
the header and the beginning of the executable data.
Initial support is added only for SPI, MMC and SATA code. We can extend
it later if needed.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and
CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less
than a year away.
Also we want to have a CONFIG_I2C for U-Boot proper just like we have
CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules.
Rename this symbol so it is clear it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
OP-TEE requires some particular setup, which is not needed for linux
or other payloads. Add a hook for platform-specific code to perform
any OP-TEE related configuration and initialization.
A weak function is used because it is symmetrical to other
spl_board_prepare_for_*() implementations. A solution to avoid the use
of weak functions would trivially apply to all these implementations.
However, re-designing this is beyond the scope of this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In general, Falcon mode means we're booting a linux kernel directly.
With FIT images, however, an OP-TEE secure kernel can be booted before
linux. Thus, if the next stage is an IH_OS_TEE, this isn't necessarily
a problem.
Of course, a general solution would involve mmc_load_image_raw_os()
only loading the binary, and leaving the decision of suitability to
someone else. However, a rework of the boot flow is beyond the scope
of this patch. Accept IH_OS_TEE as a valid OS value.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This adds tests for the crypt-based and plain SHA256-based password hashing
algorithms in the autoboot flow.
Signed-off-by: Steffen Jaeckel <jaeckel-floss@eyet-services.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In case crypt-based hashing is enabled this will be the default mechanism
that is used. If a user wants to have support for both, the environment
variable `bootstopusesha256` can be set to `true` to allow plain SHA256
based hashing of the password.
Signed-off-by: Steffen Jaeckel <jaeckel-floss@eyet-services.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The key-sequence based unlock mechanisms are sensitive to junk symbols
that could have been sent to stdin and are still waiting to be retrieved.
Enabling this option will read all symbols off stdin before displaying the
autoboot prompt (and starting to read the password from stdin).
Signed-off-by: Steffen Jaeckel <jaeckel-floss@eyet-services.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In case a user has to enter a complicated password it is sometimes
desireable to give the user more time than the default timeout.
Enabling this feature will disable the timeout entirely in case the user
presses the <Enter> key before entering any other character.
Signed-off-by: Steffen Jaeckel <jaeckel-floss@eyet-services.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
While doing code-review internally this got nitpicked by 2 reviewers, so
I decided to include this here.
Signed-off-by: Steffen Jaeckel <jaeckel-floss@eyet-services.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Hook into the autoboot flow as an alternative to the existing
mechanisms.
Signed-off-by: Steffen Jaeckel <jaeckel-floss@eyet-services.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
When we build U-Boot with POSITION_INDEPENDENT we must have
SYS_TEXT_BASE be set to zero. Make this the default in that case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Switch to fit_image_get_data_and_size() for consistency with all other
data loaded from FIT.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It's possible that LOAD_FIT_FULL will have different values for TPL and
SPL, in which case just checking CONFIG_SPL_LOAD_FIT_FULL causes this to
be compiled in to the TPL even though functions and struct members it
depends on are not.
Use CONFIG_IS_ENABLED() to ensure the correct TPL/SPL variant is
checked.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present when function names are logged, the output is a little hard to
read since every function is a different length. Add a way to pad the
names so that the log messages line up vertically. This doesn't work if
the function name is very long, but it makes a big difference in most
cases.
Use 20 characters as a default since this covers the vast majority of
functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
If SPL fails to boot, try to provide an error code to indicate what is
wrong. For example, if a uclass is missing, this can return -EPFNOSUPPORT
(-96) which provides useful information.
Add a helper for accessing the image-loader name so we can drop the use
of #ifdefs in this code.
Put this feature behind a CONFIG_SHOW_ERRORS option to avoid increasing
the code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
If signature verification is not in use we don't need to worry about
the risk of using @ in node names. Update fit_image_verify() to allow
it if the function is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is possible to add a blob that ends at the end of the bloblist, but at
present this is not supported. Fix it and add a regression test for this
case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes a blob needs to expand, e.g. because it needs to hold more log
data. Add support for this. Note that the bloblist must have sufficient
spare space for this to work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Function pointers from crypto_algos array are relocated, when
NEEDS_MANUAL_RELOC is set. This relocation doesn't happen if the algo
is placed in a linker list. Implement this relocation.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Crytographic algorithms (currently RSA), are stored in linker lists.
The crypto_algos array is unused, so remove it, and any logic
associated with it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the RSA verification crytpo_algo structure out of the
crypto_algos array, and into a linker list.
Although it appears we are adding an #ifdef to rsa-verify.c, the gains
outweigh this small inconvenience. This is because rsa_verify() is
defined differently based on #ifdefs. This change allows us to have
a single definition of rsa_verify().
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The purpose of this change is to enable crypto algorithms to be placed
in linker lists, rather than be declared as a static array. The goal
is to remove the crypto_algos array in a subsequent patch.
Create a new linker list named "cryptos", and search it when
image_get_crypto_algo() is invoked.
NOTE that adding support for manual relocation of crypto_algos within
linker lists is beyond the scope of this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove any ifdefs in image-sig.c that were previously used to
differentiate from the host code. Note that all code dedicated to
relocating ->sign() and ->add_verify_data)_ can be safely removed,
as signing is not supported target-side.
NOTE that although it appears we are removing ecdsa256 support, this
is intentional. ecdsa_verify() is a no-op on the target, and is
currently only used by host code.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We already have a host Kconfig for these SHA options. Use
CONFIG_IS_ENABLED(SHAxxx) directly in the code shared with the host build,
so we can drop the unnecessary indirections.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We already have a host Kconfig for SHA1. Use CONFIG_IS_ENABLED(SHA1)
directly in the code shared with the host build, so we can drop the
unnecessary indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Drop the _SUPPORT suffix so we can use CONFIG_IS_ENABLED() with this
option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Drop the _SUPPORT suffix so we can use CONFIG_IS_ENABLED() with this
option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Drop the ENABLE and SUPPORT parts of this, which are redundant.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
These option are named inconsistently with other SPL options, thus making
them incompatible with the CONFIG_IS_ENABLED() macro. Rename them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The ENABLE part of this name is redundant, since all boolean Kconfig
options serve to enable something. The SUPPORT part is also redundant
since Kconfigs can be assumed to enable support for something. Together
they just serve to make these options overly long and inconsistent
with other options.
Rename FIT_ENABLE_SHAxxx_SUPPORT to FIT_SHAxxx
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
At the moment android_image_get_kcomp() can automatically detect
LZ4 compressed kernels and the compression specified in uImages.
However, especially on ARM64 Linux is often compressed with GZIP.
Attempting to boot an Android image with a GZIP compressed kernel
image currently results in a very strange crash, e.g.
Starting kernel ...
"Synchronous Abort" handler, esr 0x02000000
...
Code: 5555d555 55555d55 555f5555 5d555d55 (00088b1f)
Note the 1f8b, which are the "magic" bytes for GZIP images.
U-Boot already has the image_decomp_type() function that checks for
the magic bytes of bzip2, gzip, lzma and lzo. It's easy to make use
of it here to increase the chance that we do the right thing and the
user does not become confused with strange crashes.
This allows booting Android boot images that contain GZIP-compressed
kernel images.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
The current fitImage DTO implementation expects each fitImage image
subnode containing DTO to have 'load' property, pointing somewhere
into memory where the DTO will be loaded. The address in the 'load'
property must be different then the base DT load address and there
must be sufficient amount of space between those two addresses.
Selecting and using such hard-coded addresses is fragile, error
prone and difficult to port even across devices with the same SoC
and different DRAM sizes.
The DTO cannot be applied in-place because fdt_overlay_apply_verbose()
modifies the DTO when applying it onto the base DT, so if the DTO was
used in place within the fitImage, call to fdt_overlay_apply_verbose()
would corrupt the fitImage.
Instead of copying the DTO to a specific hard-coded load address,
allocate a buffer, copy the DTO into that buffer, apply the DTO onto
the base DT, and free the buffer.
The upside of this approach is that it is no longer necessary to
select and hard-code specific DTO load address into the DTO. The
slight downside is the new malloc()/free() overhead for each DTO,
but that is negligible (*).
(*) on iMX8MM/MN and STM32MP1
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add <linux/sizes.h>]
Signed-off-by: Tom Rini <trini@konsulko.com>
The sysinfo_get_str() implementation checks whether the sysinfo was even
detected. In U-Boot proper, sysinfo_detect() is not called anywhere but
on one specific board. Call sysinfo_detect() before sysinfo_get_str() to
make sure the sysinfo is detected and sysinfo_get_str() returns valid
value instead of -EPERM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace uclass_first_device_err(UCLASS_SYSINFO, &dev) with sysinfo_get(&dev).
The board_info code may use sysinfo to print board information, so use the
sysinfo functions consistently. The sysinfo_get() is internally implemented
as return uclass_first_device_err(UCLASS_SYSINFO, &dev) anyway, so there is
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Factor out eMMC boot partition selection code into
default_spl_mmc_emmc_boot_partition() function and implement
weak spl_mmc_emmc_boot_partition(), so that architecture or
board code can override the eMMC boot partition selection.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Harald Seiler <hws@denx.de>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When we do not have bootstage enabled, rather than include an empty
dummy function, we just don't reference it. This saves us space in some
tight builds. This also shows a few cases where show_boot_progress was
incorrectly guarded before.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
GCC provides a symbol _init in crti.o on x86_64 and aarch64 but not on
RISC-V. The following lines leads to a build error for sandbox_defconfig on
RISC-V due to the missing symbol:
common/board_f.c:269:
#elif defined(CONFIG_SANDBOX) || defined(CONFIG_EFI_APP)
gd->mon_len = (ulong)&_end - (ulong)_init;
The sandbox code is not copied into the memory allocated using mmap().
Hence we can safely use gd->mon_len = 0 to avoid the reference to _init.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYN105QAKCRDKSWXLKUoM
IZiFAJ9CIiEpHiBbnAhA0VOMGoaXHGULywCdED/5dNgVtc1C7y4avzETbEyWzD4=
=CdMa
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.10
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
The original code is in the public domain. Licenses/README states that the
general license for U-Boot is GPL 2.0+. So we can mark the malloc code as
GPL 2.0+ too.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
On ARM64 secure OS can run as 64bit or 32bit that's why it is necessary to
record information about architecture that other code can read it and
properly pass it to TF-A and start in 64bit or 32bit mode.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace typo CONFIG_USE_AUTOBOOT_MENUKEY with
CONFIG_AUTOBOOT_USE_MENUKEY as when they were introduced initially there
was some mismatch in which name was used where.
Fixes: 8fc31e23aa ("autoboot: Rename CONFIG_MENUKEY to CONFIG_AUTOBOOT_MENUKEY")
Signed-off-by: Da Xue <da@libre.computer>
board_fit_image_post_process() passes only start and size of the image,
but type of the image is not passed. So pass fit and node_offset, to
derive information about image to be processed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
If the console output buffer is exhausted, characters are silently dropped
from the end. Detect this condition and report an error when reading back
the characters.
Signed-off-by: Simon Glass <sjg@chromium.org>
Save the 'no-map' information present in 'reserved-memory' node to allow
correct handling when the MMU is configured in board to avoid
speculative access.
This binding is defined in
doc/device-tree-bindings/reserved-memory/reserved-memory.txt
Additional properties:
...
no-map (optional) - empty property
- Indicates the operating system must not create a virtual mapping
of the region as part of its standard mapping of system memory,
nor permit speculative access to it under any circumstances other
than under the control of the device driver using the region.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
When we think of Kconfig, we usually think of features that we like
to enable or not. Ideally, we wouldn't use Kconfig to fix a build
issue, although sometimes it might make sense. With Kconfig it's hard
to guarantee that the fix is universal. We can only say that it works
for the set of tested configurations. In the majority of cases, it's
preferable to let the linker figure things out for us.
The reverted commit attempted to fix a build issue by adding an
invisible Kconfig option. This is wrong in several ways:
It invents a new Kconfig variable when CONFIG_HASH already
exists for the same purpose.
Second, hash-checksum.c makes use of the hash_progressive_lookup_algo()
symbol, which is only provided with CONFIG_HASH, but this dependency
was not expressed in the reverted patch.
It feels like Kconfig is turning into a listing of all available
source files, and a buffet to 'select' which ones to compile. The
purpose of this revert is to enable the next change to make use of
CONFIG_HASH instead of adding to Kconfig.
This reverts commit 87316da05f.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Masahisa Kojima <masahisa.kojima@linaro.org>
A lot of entries were using spaces instead of tab for alignment that's why
it is good to fix it to use the same style everywhere.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have switched to binman to generate u-boot.itb for all
RISC-V boards, USE_SPL_FIT_GENERATOR is no longer needed and can
be dropped.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It should be FDT, not FTD.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Build error occurs when CONFIG_EFI_SECURE_BOOT or
CONFIG_EFI_CAPSULE_AUTHENTICATE is enabled,
because hash-checksum.c is not compiled.
Since hash_calculate() implemented in hash-checksum.c can be
commonly used aside from FIT image signature verification,
this commit itroduces HASH_CALCULATE option to decide
if hash-checksum.c shall be compiled.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Commit a479f103dc ("hash: Allow for SHA512 hardware implementations")
defined function definitions for hardware accelerated SHA384 and SHA512.
If CONFIG_SHA_HW_ACCEL=y, these functions are used.
We already have boards using CONFIG_SHA_HW_ACCEL=y but none implements the
new functions hw_sha384() and hw_sha512().
For implementing the EFI TCG2 protocol we need SHA384 and SHA512. The
missing hardware acceleration functions lead to build errors on boards like
peach-pi_defconfig.
Introduce a new Kconfig symbol CONFIG_SHA512_HW_ACCEL to control if the
functions hw_sha384() and hw_sha512() shall be used to implement the SHA384
and SHA512 algorithms.
Fixes: a479f103dc ("hash: Allow for SHA512 hardware implementations")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the fdt_valid function to fdt_support.
This changes allow to be able to test the validity of a devicetree in
other c files.
Update code syntax.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
By declaring board-specific board_fdt_chosen_bootargs() the kernel
command line arguments can be adjusted before injecting to flat dt
chosen node.
Signed-off-by: Niko Mauno <niko.mauno@vaisala.com>
It can be useful to use the same U-Boot binary for multiple purposes,
say the normal one, one for developers that allow breaking into the
U-Boot shell, and one for use during bootstrapping which runs a
special-purpose bootcmd. Or one can have several board variants that
can share almost all boot logic, but just needs a few tweaks in the
variables used by the boot script.
To that end, allow the control dtb to contain a /config/enviroment
node (or whatever one puts in fdt_env_path variable), whose
property/value pairs are used to update the run-time environment after
it has been loaded from its persistent location.
The indirection via fdt_env_path is for maximum flexibility - for
example, should the user wish (or board logic dictate) that the values
in the DTB should no longer be applied, one simply needs to delete the
fdt_env_path variable; that can even be done automatically by
including a
fdt_env_path = "";
property in the DTB node.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This has the uclass enforce calling detect() before other methods. This
allows drivers to cache information in detect() and perform (cheaper)
retrieval in the other accessors. This also modifies the only instance
where this sequencing was not followed.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use of strcat() against an uninitialized buffer would lead
to buffer overflow. This patch fixes it.
Fixes: 694cd5618c ("IOMUX: Introduce iomux_replace_device()")
Signed-off-by: Yuichiro Goto <goto@k-tech.co.jp>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
One of my monitors have only 4k@60 timing in base EDID block which is
out of range for devices with HDMI 1.4. It turns out that it has
additional detailed timings in CTA-861 Extension Block and two of them
are appropriate for HDMI 1.4.
Add additional search for valid detailed timing in extension block.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Code which searches for valid detailed timing entry will be used in more
places. Extract it.
No functional change is made. However, descriptors are casted to
edid_detailed_timing instead of edid_monitor_descriptor. Descriptor can
be of either type, but since we're interested only in DTD, it is more
fitting to cast to edid_detailed_timing.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When searching for detailed timing in EDID, check for digital display
earlier. There is no point parsing other parameters if this flag is not
present.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add support for stack protector for UBOOT, SPL, and TPL
as well as new pytest for stackprotector
Signed-off-by: Joel Peshkin <joel.peshkin@broadcom.com>
Adjust UEFI build flags.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This reverts commit 38d6b7ebda.
struct global_data contains a pointer to the bd_info structure. This
pointer was populated spl_set_bd() to a pre-allocated bd_info in the
".data" section. The referenced commit replaced this mechanism to one
that uses malloc(). That new mechanism is only used if SPL_ALLOC_BD=y.
which very few boards do.
The result is that (struct global_data)->bd is NULL in SPL on most
platforms. This breaks falcon mode, since arch_fixup_fdt() tries to
access (struct global_data)->bd and set the "/memory" node in the
devicetree. The result is that the "/memory" node contains garbage
values, causing linux to panic() as it sets up the page table.
Instead of trying to fix the mess, potentially causing other issues,
revert to the code that worked, while this change is reworked.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
OP-TEE images are normally packaged with
type = "tee;
os = "tee";
However, fit_image_load() thinks that is somehow invalid. However if
they were declared as type = "kernel", os = "linux", fit_image_load()
would happily accept them and allow the boot to continue. There is no
technical limitation to excluding "tee".
Allowing "tee" images is useful in a boot flow where OP-TEE is
executed before linux.
In fact, I think it's unintuitive for a "load"ing function to also do
parsing and contain a bunch ad-hoc heuristics that only its caller
might know. But I don't make the rules, I just write fixes. In more
polite terms: refactoring the fit_image API is beyond the scope of
this change.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Consider the following FIT:
images {
whipple {};
};
configurations {
conf-1 {
firmware = "whipple";
};
};
Getting the 'firmware' image with fit_image_load() is not possible, as
it doesn't understand 'firmware =' properties. Although one could pass
IH_TYPE_FIRMWARE for 'image_type', this needs to be converted to a
"firmware" string for FDT lookup -- exactly what this change does.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'firmware' property of a config node takes precedence over the
'kernel' property. 'standalone' is deprecated. However, give users a
couple of releases where 'standalone' still works, but warns loudly.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
U-Boot expects the FDT to be located right after the _end
linker symbol (see fdtdec.c: board_fdt_blob_setup())
The "basic" LOAD_FIT path is aware of this limitation, and relocates
the FDT at the expected location. Guessing the expected location
probably only works reliably on 32-bit arm, and it feels like a hack.
One proposal would be to pass the FDT address to u-boot
(e.g. using 'r2' on arm platforms).
The variable is named "fdt_hack" to remind future contributors that,
"hey! we should fix the underlying problem". However, that is beyond
the scope of this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The information on the OS should be contained in the FIT, as the
self-explanatory "os" property of a node under /images. Hard-coding
this to U_BOOT might send us down the wrong path later in the boot
process.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The correct FDT to use is described by the "fdt" property of the
configuration node. When the fit_unamep argument to fit_image_load()
is "fdt", we get the "/images/fdt" node. This is incorrect, as it
ignores the "fdt" property of the config node, and in most cases,
the "/images/fdt" node doesn't exist.
Use NULL for the 'fit_unamep' argument. With NULL, fit_image_load()
uses the IH_TYPE_FLATDT value to read the config property "fdt",
which points to the correct FDT node(s).
fit_image_load() should probably be split into a function that reads
an image by name, and one that reads an image by config reference. I
don't make those decisions, I just point out the craziness.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several architectures had a default board_fit_config_name_match already;
this provides a generic weak version. We default to rejecting all configs.
This will use the FIT's default config, instead of the first config. This
may result in boot failures if there are multiple configurations and the
first config is *not* the default.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The "simple" SPL_LOAD_FIT path is the most compliant with the format
documented in doc/uImage.FIT/source_file_format.txt. The other two
paths to load a FIT are SPL_LOAD_FIT_FULL and the "bootm" command.
Since the Kconfig menu is the most likely place for a new user to see
these options, it seems like the most logical candidate to document
the limitations. This documents the _known_ issues, and is not
intended to be a complete list of all follies.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 4afc4f37c7 ("doc: FIT image: Clarify format and simplify
syntax") and delegated FPGA images to be added via the list of
"loadables" in lieu of the "fpga" property. Now actually implement
this in code.
Note that the "compatible" property is ignored for the time being, as
implementing "compatible" loading is beyond the scope of this change.
However, "u-boot,fpga-legacy" is accepted without warning.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Commit 4afc4f37c7 ("doc: FIT image: Clarify format and simplify
syntax") requires that FPGA images be referenced through the
"loadables" in the config node. This means that "fpga" properties in
config nodes are deprecated.
Given that there are likely FIT images which use "fpga", let's not
break those right away. Print a warning message that such use is
deprecated, and give users a couple of releases to update their
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The FPGA loading code in spl_simple_fit_read() can easily be separated
from the rest of the logic. It is split into two functions instead of
one because spl_fit_upload_fpga() is used in a subsequent patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
spl_load_fit_image() will try to load an image at the address given
in the "load" property. Absent such property, it uses
image_info->load_addr
Correct use of this is demonstrated in spl_fit_append_fdt(), which
resets the 'load_addr' before each spl_load_fit_image() call.
On the other hand loading "loadables" loop in spl_load_simple_fit()
completely ignores this. It re-uses the same structure, but doesn't
reset load_addr. If loadable [i] does not have a "load" property, its
load address defaults to load_addr, which still contains the address
of loadable [i - 1].
A simple solution is to treat NULL as an invalid load address. The
caller can set load_addr = 0 to request an abort if the "load"
property is absent.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mkimage supports rsa2048, and rsa4096 signatures. With newer silicon
now supporting hardware-accelerated ECDSA, it makes sense to expand
signing support to elliptic curves.
Implement host-side ECDSA signing and verification with libcrypto.
Device-side implementation of signature verification is beyond the
scope of this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
rsa-checksum.c sontains the hash_calculate() implementations. Despite
the "rsa-" file prefix, this function is useful for other algorithms.
To prevent confusion, move this file to lib/, and rename it to
hash-checksum.c, to give it a more "generic" feel.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We move qfw into its own uclass and split the PIO functions into a
specific driver for that uclass. The PIO driver is selected in the
qemu-x86 board config (this covers x86 and x86_64).
include/qfw.h is cleaned up and documentation added.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
If there were no variable substitutions in a command, then initial
assignments would be misinterpreted as commands, instead of being skipped
over. This is demonstrated by the following example:
=> foo=bar echo baz
Unknown command 'foo=bar' - try 'help'
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Similar to support for SHA1 and SHA256, allow the use of hardware hashing
engine by enabling the algorithm and setting CONFIG_SHA_HW_ACCEL /
CONFIG_SHA_PROG_HW_ACCEL.
Signed-off-by: Joel Stanley <joel@jms.id.au>
The optee_copy_fdt_nodes is only used to copy op-tee nodes
of U-Boot device tree (from gd->fdt_blob when OF_LIVE is not activated)
to external device tree but it is not compatible with OF_LIVE.
This patch migrates all used function fdt_ functions to read node on
old_blob to ofnode functions, compatible with OF_LIVE and remove this
parameter "old_blob".
The generated "device tree" is checked on stm32mp platform with OF_LIVE
activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Update the debug trace for the reserved video memory to KB as indicated
in the message with "%luk"; before the patch the computed size
gd->relocaddr - addr is in bytes.
This patch aligns the debug trace in reserve_video() with others
functions, for example on stm32mp157c-dk2:
- Reserving 3080192k for video at: dfd00000
+ Reserving 3008k for video at: dfd00000
Reserving 873k for U-Boot at: dfc25000
Reserving 32776k for malloc() at: ddc23000
Reserving 72 Bytes for Board Info at: ddc22fb0
Reserving 280 Bytes for Global Data at: ddc22e90
Reserving 119072 Bytes for FDT at: ddc05d70
Reserving 0x278 Bytes for bootstage at: ddc05af0
Fixes: 5630d2fbc5 ("board: Show memory for frame buffers")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a weak nand_get_mtd function for nand drivers to provide mtd info
and use this to set pagesize such that reading of non page-aligned
elements can succeed.
The spl_load_simple_fit already handles block block access so all we
need to do is provide the nand writesize as the block length.
Further cleanup of the drivers which use nand_spl_loaders.c such as
am335x_spl_bch.c, atmel_nand.c, and nand_spl_simple.c could be done
using info from mtd_info instead of statically defined details.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
commit 9f6a14c47f ("spl: fit: nand: fix fit loading in case of bad blocks")
added support for adjusting the image offset to account for bad blocks.
However this requires nand_spl_adjust_offset() which requires fully defined
specifics of the NAND chip being used may not be avialable.
Allow skipping this support for drivers or configs which don't specify
the NAND chip details statically with defines.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In preparation to add SiFive Unmatched board support, let's rename
the existing fu540 board to unleashed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add missing endianness conversions to usb_get_port_status(). This
(amongst others) is necessary to enable the use of USB 3 hubs on
big-endian platforms like MIPS Octeon.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Some boards may want to show the SKU ID or other information obtained at
runtime. Allow this to come from sysinfo. The board can then provide a
sysinfo driver to provide it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The _SUPPORT suffix is from an earlier time and interferes with use of
the CONFIG_IS_ENABLED() macro. Rename the option to drop the suffix.
Tidy up the TODO that prompted this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present bootstage silently ignores new records if it runs out of
space. It is sometimes obvious by looking at the report, but the IDs are
not contiguous, so it is easy to miss.
Aad a message so that action can be taken.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have two separate places that need to figure out the bootstage ID to
use. Put this code in a function so that the logic is in one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox is special in that it is used for testing and it does not match
any particular target architecture. Allow it to load an image from any
architecture, so that 'bootm' can be used as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some systems (e.g. x86 APL) run SPL from read-only memory. The device
instances created by dtoc are therefore not writeable. To make things work
we would need to copy the devices to read/write memory.
To avoid this, add an option to use a separate runtime struct for devices,
just as is done for drivers. This can be used to hold information that
changes at runtime, avoiding the need for a copy.
Also add a Kconfig option for read-only SPL, which selects this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
part_get_info_by_name will return -1 on error, and >0 on success.
Signed-off-by: schspa <schspa@gmail.com>
Cc: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Unfortunately -ENODATA is not available in OpenBSD. Use -EBADMSG
instead, to indicate a missing timestamp.
Fixes: c5819701a3 image: Adjust the workings of fit_check_format()
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
This Trusted Application allows enabling SCP03 as well as provisioning
the keys on TEE controlled secure element (ie, NXP SE050).
All the information flowing on buses (ie I2C) between the processor
and the secure element must be encrypted. Secure elements are
pre-provisioned with a set of keys known to the user so that the
secure channel protocol (encryption) can be enforced on the first
boot. This situation is however unsafe since the keys are publically
available.
For example, in the case of the NXP SE050, these keys would be
available in the OP-TEE source tree [2] and of course in the
documentation corresponding to the part.
To address that, users are required to rotate/provision those keys
(ie, generate new keys and write them in the secure element's
persistent memory).
For information on SCP03, check the Global Platform HomePage and
google for that term [1]
[1] globalplatform.org
[2] https://github.com/OP-TEE/optee_os/
check:
core/drivers/crypto/se050/adaptors/utils/scp_config.c
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
When multiple log() calls are used which don't end in newline, the
log prefix is prepended multiple times in the same line. This makes the
output look strange.
Fix this by detecting when the previous log record did not end in newline.
In that case, setting a flag.
Drop the unused BUFFSIZE in the test while we are here.
As an example implementation, update log_console to check the flag and
produce the expected output.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only a single flag (force_debug) is used in log records. Before
adding more, convert this into a bitfield, so more can be added without
using more space.
To avoid expanding the log_record struct itself (which some drivers may
wish to store in memory) reduce the line-number field to 16 bits. This
provides for up to 64K lines which should be enough for anyone.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this casts addresses to pointers so cannot work with sandbox.
Update the code to use map_sysmem() instead.
As part of this change, the existing load_ptr is renamed to src_ptr since
it is not a pointer to load_addr. It is confusing to use a similar name
for something that is not actually related. For the alignment code,
ALIGN() is used instead of open-coded alignment. Add a comment to the line
that casts away a const.
Use a (new) load_ptr variable to access memory at address load_addr.
Signed-off-by: Simon Glass <sjg@chromium.org>
Vendor Authorized Boot is a security feature for authenticating
the images such as U-Boot, ARM trusted Firmware, Linux kernel,
device tree blob and etc loaded from FIT. After those images are
loaded from FIT, the VAB certificate and signature block appended
at the end of each image are sent to Secure Device Manager (SDM)
for authentication. U-Boot will validate the SHA384 of the image
against the SHA384 hash stored in the VAB certificate before
sending the image to SDM for authentication.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
At present initr_addr_map() is put at a late stage in the
init_sequence_r[] calls. This won't work because lot of
device driver initialization (e.g.: serial port) happens
before it but is lack of the address translation support.
This moves the call to a bit earlier, right after the DM
initialization.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present fdt_read_prop() can only handle 1 or 2 cells. It is
called by fdt_read_range() which may be used to read PCI address
from <ranges> for a PCI bus node where the number of PCI address
cell is 3. The <ranges> property is an array of:
{ <child address> <parent address> <size in child address space> }
When trying to read <child address> from a PCI bus node using
fdt_read_prop(), as the codes below:
/* Read <child address> */
if (child_addr) {
r = fdt_read_prop(ranges, ranges_len, cell, child_addr,
acells);
if (r)
return r;
}
it will fail, because the PCI child address is made up of 3 cells
but fdt_read_prop() cannot handle it. We advance the cell offset
by 1 so that the <child address> can be correctly read.
This adds the special handling of such case.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present these three Kconfigs exist even when bootstage is not enabled.
This is not necessary since bootstage.c is only built if BOOTSTAGE is
enabled.
Make them conditional. Also fix up the overflow message to mention TPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is printed twice but we only need one message, since there is very
little processing in between them. Drop the second one, since all branches
of the switch() already have output. Update the U-Boot message to include
the phase being jumped to.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some compression algorithms currently can be enabled for SPL and
U-Boot proper separately. Therefore take into account USE_HOSTCC
is well as CONFIG_IS_ENABLED() in these cases to prevent compiling these
functions in case of a host tool build.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The OUT endpoint can just be ignored as it is not used, just as the
corresponding Set_Report request for IN-only interfaces. E.g. the
Linux gadget hid keyboard also provides an interrupt endpoint.
Also cleanup confusing debug messages like "found set protocol", which
is printed when a keyboard device is found, while the Set_Protocol request
is issued quite some time later.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Having the ability to support firmware FIT signatures on the SPL sounds
not so useful if the SPL is not supporting to load a (U-boot) firmware
as a FIT image.
Signed-off-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Selecting SPL_FIT_SIGNATURE (without selecting U-boot proper
verified boot first) breaks the build due to
CONFIG_FIT_SIGNATURE_MAX_SIZE being undefined, in addition to Kconfig
warnings on RSA and IMAGE_SIGN_INFO unmet dependencies.
Signed-off-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Sometimes it is useful to boot OS with already fixed-up
device tree. Check for env variable 'skip_board_fixup'
before calling ft_board_setup().
Current behaviour is unchanged, additionally user can
set skip_board_fixup to 1 to skip the fixup.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
OF_STDOUT_PATH was meant to hold the devicetree path to the serial
console, to be put into the linux,stdout-path property of the chosen node.
The only user of that was sunxi, and it was actually wrong for years
there: the paths hardcoded in sunxi_common.h were not matching the DTs,
evident by the leading 0's in nodenames, which have been removed years
ago.
On top of that, "linux,stdout-path" is now deprecated for a while (Linux
commit 2a9d832cc9aae from November 2014), and also all modern DTs
(including those included in U-Boot) carry a "stdout-path" property
already.
So remove the stanza from sunxi_common.h, and, since this was the last
user, also remove the associated bits from the rest of U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix -Wint-to-pointer-cast warning
common/splash_source.c: In function 'splash_load_raw':
common/splash_source.c💯12: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
100 | bmp_hdr = (struct bmp_header *)bmp_load_addr;
| ^
common/splash_source.c: In function 'splash_sf_read_raw':
common/splash_source.c:39:47: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
39 | return spi_flash_read(sf, offset, read_size, (void *)bmp_load_addr);
| ^
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the following functions to get a specific device's DMA ranges:
- dev_get_dma_range()
- ofnode_get_dma_range()
- of_get_dma_range()
- fdt_get_dma_range()
They are specially useful in oder to be able validate a physical address
space range into a bus's and to convert addresses from and to address
spaces.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
When a FIT config specifies a devicetree, we should load it, no
questions asked. In the case of the "simple" FIT loading path, a
difficulty arises in selecting the load address of the FDT.
The default FDT location is right after the "kernel" or "firmware"
image. However, if that is an OP-TEE image, then the FDT may end up in
secure DRAM, and not be accessible to normal world kernels.
Although the best solution is to be more careful about the FDT
address, a viable workaround is to only append the FDT after a u-boot
or Linux image. This is identical to the previous logic, except that
FDT loading is extended to IH_OS_LINUX images.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Use the IS_ENABLED() macro to control code flow, instead of the
caveman approach of sprinkling #ifdefs. Code size is not affected, as
the linker garbage-collects unused functions. However, readability is
improved significantly.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The configuration node a sub node under "/configurations", which
describes the components to load from "/images". We only need to
locate this node once.
However, for each component, spl_fit_get_image_name() would parse the
FIT image, looking for the correct node. Such work duplication is not
necessary. Instead, once the node is found, cache it, and re-use it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a desired configuration is not found, conf_node will have a
negative value. Thus the for loop will start at the root "/" node of
the image, print the "/description" property, and stop.
It appears the intent of the loop was to print the names of the
subnodes under "/configurations". We would need the offset to the
"/configurations" node, which is abstracted by fit_find_config_node().
This change agrees that abstracting the node offset is the correct
design, and we shouldn't be parsing the configurations manually. Thus
the loop in spl_fit_get_image_name() is useless. Remove it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several loose arguments describe the FIT image. They are thus related,
and it makes sense to pass them together, in a structure. Examples
include the FIT blob pointer, offset to FDT nodes, and the offset to
external data.
Use a spl_fit_info structure to group these parameters.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The logical steps in spl_load_simple_fit() are difficult to follow.
I think the long comments, ifdefs, and ungodly number of variables
seriously affect the readability. In particular, it violates section 6
of the coding style, paragraphs (3), and (4).
The purpose of this patch is to improve the situation by
- Factoring out initialization and parsing to separate functions
- Reduce the number of variables by using a context structure
This change introduces no functional changes.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The size is derived from the FIT image itself. Any alignment
requirements are machine-specific and known by the board code. Thus
the total length can be derived from the FIT image and knowledge of
the platform. The 'length' argument is redundant. Remove it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CC: Matt Porter <mporter@konsulko.com>
In case of IOMUX enabled it assumes that console devices in the list
are available to get them stopped properly via ->stop() callback.
However, the USB keyboard driver violates this assumption and tries
to play tricks so the device get destroyed while being listed as
an active console.
Swap the order of device deregistration and IOMUX update along with
converting to use iomux_replace_device() jelper to avoid the use-after-free.
Fixes: 3cbcb28928 ("usb: Fix usb_kbd_deregister when console-muxing is used")
Fixes: 8a83487030 ("dm: usb: Add a remove() method for USB keyboards")
Reported-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some console devices may appear or disappear at run time. In order to
support such a hotplug mechanism introduce a new iomux_replace_device()
helper to update the list of devices without altering environment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It is not only less lines of code, but also better readability
when new macro is being in use. Introduce for_each_console_dev()
helper macro and convert current users to it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Logical continuation of the change that brought console_devices_set() is
to unify console_setfile() with it and replace in the callers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
console_devices_set() missed the console device counter to be set correctly.
Fixes: 45375adc97 ("console: add function console_devices_set")
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It's possible that NULLDEV can be disabled while it makes leftovers,
move entire device under #if.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Nobody is using stdio_deregister(), remove for good.
Note, even its parameters are not consistent with stdio_register().
So, if anyone want to introduce this again, better with some consistency.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Using unit addresses in a FIT is a security risk. Add a check for this
and disallow it.
CVE-2021-27138
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bruce Monroe <bruce.monroe@intel.com>
Reported-by: Arie Haenel <arie.haenel@intel.com>
Reported-by: Julien Lenoir <julien.lenoir@intel.com>
Some strange modifications of the FIT can introduce security risks. Add an
option to check it thoroughly, using libfdt's fdt_check_full() function.
Enable this by default if signature verification is enabled.
CVE-2021-27097
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bruce Monroe <bruce.monroe@intel.com>
Reported-by: Arie Haenel <arie.haenel@intel.com>
Reported-by: Julien Lenoir <julien.lenoir@intel.com>
At present this function does not accept a size for the FIT. This means
that it must be read from the FIT itself, introducing potential security
risk. Update the function to include a size parameter, which can be
invalid, in which case fit_check_format() calculates it.
For now no callers pass the size, but this can be updated later.
Also adjust the return value to an error code so that all the different
types of problems can be distinguished by the user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bruce Monroe <bruce.monroe@intel.com>
Reported-by: Arie Haenel <arie.haenel@intel.com>
Reported-by: Julien Lenoir <julien.lenoir@intel.com>
When searching for a node called 'fred', any unit address appended to the
name is ignored by libfdt, meaning that 'fred' can match 'fred@1'. This
means that we cannot be sure that the node originally intended is the one
that is used.
Disallow use of nodes with unit addresses.
Update the forge test also, since it uses @ addresses.
CVE-2021-27138
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bruce Monroe <bruce.monroe@intel.com>
Reported-by: Arie Haenel <arie.haenel@intel.com>
Reported-by: Julien Lenoir <julien.lenoir@intel.com>
At present fdt_find_regions() assumes that the FIT is a valid devicetree.
If the FIT has two root nodes this is currently not detected in this
function, nor does libfdt's fdt_check_full() notice. Also it is possible
for the root node to have a name even though it should not.
Add checks for these and return -FDT_ERR_BADSTRUCTURE if a problem is
detected.
CVE-2021-27097
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bruce Monroe <bruce.monroe@intel.com>
Reported-by: Arie Haenel <arie.haenel@intel.com>
Reported-by: Julien Lenoir <julien.lenoir@intel.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Config allows to disable printing contents of fitImage to optimize boottime.
Signed-off-by: Ravik Hasija <rahasij@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is useful to know the TEXT_BASE value for the image being loaded in
TPL/SPL. Add a new spl_get_image_text_base() function to handle this.
Make use of this in the x86 SPL handler, instead of having the logic
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reinitialize DFU USB gadget after flashing the 'SCRIPT' entity to ensure
that the potential changes to the 'dfu_alt_info' environment variable are
applied.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[lukma - I've moved the bool retry to avoid build (CI) errors]
AVB Verified Boot uses functions related to MMC.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
If both stop key and delay key are empty, the length of these
keys is 0. The subtraction operation will cause the u_int type
variable to overflow, will cause illegal memory access in key
input loop.
This commit fixes this bug by using int type instead of u_init.
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add tag names for recently added types.
Fixes: d2cb7a22da (x86: Allow putting some tables in the bloblist)
Signed-off-by: Simon Glass <sjg@chromium.org>
Typically in TPL/SPL the bloblist is quite small. But U-Boot proper may
want to add a lot more to it, such as ACPI tables.
Add a way to expand the bloblist by relocating it in U-Boot proper, along
with the other relocation activities.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to figure out which phase we are loading next and
which phase we came from. Add some functions to handle this as well as
returning the name of a phase. This allows messages like "Booting to x"
where x is the next phase.
At present, TPL says 'Jumping to U-Boot' at the end, when in fact it is
jumping to SPL. This is confusing, so use the new functions to correct
this.
Tests for this will come with an upcoming minor SPL test refactor.
Signed-off-by: Simon Glass <sjg@chromium.org>
In fit_config_verify_sig(), when no 'signature*' subnode exists in
the configuration node, the fdt_for_each_subnode() loop is a no-op.
Therefore, no error flags are set, and 'err_,sg' is not populated
with an error string. This is incorrect behavior.
Populate err_msg to indicate that no 'signature' is found, before
entering the loop. The first call to fit_image_verify_sig() will
override clear err_msg, or set it to a more specific message.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit add an option TPL_BOOTCOUNT_LIMIT to
use bootcount on TPL.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM
driver and need for PMIC configuration, which pulls several drivers which
are not needed otherwise.
spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with
that, reported in SPL header. If size in header is bigger, it will use
that value instead.
In the process of function rework, also add missing function argument.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When CONFIG_FIT_CIPHER=y and CONFIG_FIT_SIGNATURE=n is there is no
implementation of image_get_host_blob for mkimage/dumpimage:
/usr/bin/ld: tools/common/image-cipher.o: in function `fit_image_decrypt_data':
image-cipher.c:(.text+0x9a): undefined reference to `image_get_host_blob'
Move the implementation to a common file so it can be shaed between
image-cipher.c and image-fit-sig.c.
Signed-off-by: Joel Stanley <joel@jms.id.au>
obj-$(CONFIG_$(SPL_TPL_)YMODEM_SUPPORT) += xyzModem.o is there,
no need obj-$(CONFIG_SPL_YMODEM_SUPPORT) += xyzModem.o
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the #if 0 present since the first version of console.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With our optimization settings the linker eliminates unused functions.
But for debugging it is better to compile with -Og or -O0. With -O0
compiling the sandbox fails due to the missing function fixup_cmdtable()
called by dm_reloc() and others.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the hash check fails on a loadable image, the SPL/TPL simply
jump to the next one. This commit changes this behaviour, when the
hash check fails on a loadable image, the function spl_load_simple_fit
stops and report an error.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There should be no need to insert non-printable characters
and this prevents line editing getting confused.
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Adds an optional SALT value to AUTOBOOT_STOP_STR_SHA256. If a string
followed by a ":" is prepended to the sha256, the portion to the left
of the colon will be used as a salt and the password will be appended
to the salt before the sha256 is computed and compared.
Signed-off-by: Joel Peshkin <joel.peshkin@broadcom.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Joel Peshkin <joel.peshkin@broadcom.com>
To: u-boot@lists.denx.de
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
When at some point environment shrinks we need to stop dropped devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Obviously the following has unnecessary indentation level in 'else' branch.
if (foo) {
...
return;
} else {
...
}
Drop indentation level by removing redundant 'else'.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refactor iomux_doenv() a bit in order to increase readability.
There is no change in code generation on x86.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It's realloc() 101 to avoid `foo = realloc(foo, ...);` call
due to getting a memory leak.
Actually it's not clear why realloc() has been used here.
If we shrink the array, the memcpy() overwrites it anyway
with the contents of a new array. If it becomes bigger,
same story.
Drop useless realloc() for good and thus preserve console list
in case of failed allocation.
Fixes: 16a28ef219 ("IOMUX: Add console multiplexing support.")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
