Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This converts the following to Kconfig:
CONFIG_MTD_CONCAT
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
As stm32f46-disco, stm32f769-disco and stm32746g-eval are very similar
except their respective device tree file. These 3 boards uses the same
TARGET_STM32F746_DISCO flag (so same include/configs/stm32f746-disco.h
and same board file board/st/stm32f746-disco/stm32f746-disco.c)
To be able to compile these 3 boards, replace the hard-coded device-tree
name in include/configs/stm32f746-disco.h by CONFIG_DEFAULT_DEVICE_TREE
which is set in each board defconfig file with the correct value.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This allows to concatenate spl and u-boot binaries together.
Previously, both binaries has to be flashed separately at the correct
offset (spl at offset 0 and u-boot at offset 0x8000).
With this patch, only one binary is generated (u-boot-with-spl.bin)
and has to be copied in flash at offset 0 using openocd for example
or simply copied in exported mass storage.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On STMicroelectronics boards, the UART can reliably go up to
2000000 bauds when connected to the on-board ST-LINK-V2 for STM32MP15
Unfortunately U-Boot will fall back to 115200 unless higher rates are
declared via CONFIG_SYS_BAUDRATE_TABLE.
This patch add the support of higher baudrates on STMicroelectronics
boards with ST-LINK.
Cc: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Set the environment variable "console", used in extlinux.conf file when it
is generated by YOCTO distribution with:
UBOOT_EXTLINUX_CONSOLE ??= "console=${console},${baudrate}"
With these 2 variables, U-Boot give dynamically the used console and
baudrate in the Linux kernel bootargs.
For the STMicroelectronics boards, the used console is ttySTM0.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
For CONFIG_DM_SERIAL it is required to increase CONFIG_SYS_MALLOC_F_LEN as
default value is not enough for memory hungry CONFIG_DM_SERIAL code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Currently, in case of arm64 bootloader and U-Boot the stack pointer is
initialized at an offset of NON_SECURE_MSRAM_SIZE from arm64 SPL's text
base address. After jumping to arm64, execution is done out of DDR.
Therefore, having an offset corresponding to the size of MSRAM does not
have any significance.
Instead, initialize the stack pointer after an offset of 4MB from the SPL
text base address. This helps in allocating larger memory for stack.
┌────────────────────┐0x80080000
│ │
│ arm64 SPL │
├────────────────────┤
│ ▲ │
│ │ │
│ STACK │
├────────────────────┤0x80480000
│ Memory for Load │
│ Buffer Allocation │
├────────────────────┤0x80800000
│ │
│ U-Boot Image │
│ │
└────────────────────┘
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This patch enables the Kconfig symbols needed for full ethernet support
on the EBB7304. Also the PHY autonegotiation timeout is increased, as
the default 5 seconds are sometime a bit short. With this, ethernet can
be used on this board. Here an example of a tftp load:
=> tftp ffffffff81000000 big
ethernet-mac-nexus@11800e0000000 Waiting for PHY auto negotiation to complete....... done
Using ethernet-mac-nexus@11800e0000000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.243
Filename 'big'.
Load address: 0xffffffff81000000
Loading: ################################################## 10 MiB
13.2 MiB/s
done
Bytes transferred = 10485760 (a00000 hex)
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves CONFIG_SYS_INIT_SP_OFFSET to a higher address so that
it does not interfere with larger U-Boot images. This was noticed, while
adding network support to the EBB7304 board.
Signed-off-by: Stefan Roese <sr@denx.de>
The Zyxel NSA310s board has the network chip Marvell Alaska 88E1318S.
Use uclass mvgbe and the compatible driver M88E1310 driver to bring
up Ethernet.
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Remove CONFIG_RESET_PHY_R.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add phy mode RGMII to kirkwood-nsa310s.dts
- Miscellaneous changes: Move constants to .c file and remove header file
board/zyxel/nsa310s/nsa310s.h, add support for large USB and SATA HDDs,
use BIT macro, add/cleanup comments, and cosmetic changes.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220412201820.10291-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
U-Boot for Turris Omnia is always compiled with MMC, SCSI and USB support,
so always enable macros for booting from these devices.
Signed-off-by: Pali Rohár <pali@kernel.org>
CONFIG_ETHPRIME defines primary ethernet device and env variable $ethact
stores currently active ethernet device.
So there is no point to set ethact= in default environment. Instead set
CONFIG_ETHPRIME properly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Replace hardcoded i2c hex values for NOR banks by named SW macros in
map_lowernorbank/map_uppernorbank env commands.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Replace hardcoded boot i2c bus num and address by existing macros when
generating env for CONFIG_EXTRA_ENV_SETTINGS.
Same macros are used in U-Boot board code when reading information from
boot i2c data.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Do not stringify env $vscfw_addr two times (once implicitly via string
operator "" and second time explicitly via __stringify() macro) and allow
to compile U-Boot without CONFIG_VSC7385_ENET (when __VSCFW_ADDR was not
defined and so macro name was stringified into CONFIG_EXTRA_ENV_SETTINGS).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As written in comment, P2020 has two possible SD switch configurations.
Extend code to detect both of them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With the commit that moves the BOOTCOMMAND to Kconfig:
970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
some stray ifdefs have been left in the header files which
are now useless.
Clean up the include files to remove these lines.
Fixes: 970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
On Layerscape platforms, the DTB is loaded from boot filesystem,
per the fdt_addr description in doc/README.distro, it must be
removed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enough space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
CONFIG_MMCROOT is only used to set mmcroot, no need a dedicated macro.
Script as below
"
for i in `ls include/configs/*.h`
do
mmcroot=`sed -n '/define.*MMCROOT/ p' $i | awk -F\" '{ print $2;}'`
if [ ! -n "$mmcroot" ]; then
continue
fi
sed -i '/define.*MMCROOT/ d' $i
sed -i 's,\" CONFIG_MMCROOT \",'$mmcroot',g' $i
done
"
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Sancloud BeagleBone Enhanced Extended WiFi (BBE Extended WiFi) has
its own devicetree file and the board can be identified by the 2nd
letter of the config string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The Sancloud BeagleBone Enhanced Lite (BBE Lite) has its own devicetree
file and the board can be identified by the 2nd letter of the config
string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-By: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This GPIO is actually an input "Q7_3V3_PCIE_WAKE#_IN" not an output, so
remove the misleaading and incorrect definition.
Cc: Tim Harvey <tharvey@gateworks.com> (re: pci: imx: use vpcie-supply if defined by device-tree)
Signed-off-by: Ian Ray <ian.ray@ge.com>
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Remove CONFIG_RESET_PHY_R symbol from all board files
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The Colibri PXA270 has been end-of-life since quite a while and would
require more and more maintenance (e.g. DM conversions).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable USB support for host controller and various USB ethernet
devices.
Example usage of USB Mass Storage (UMS) support:
u-boot=> mmc list
FSL_SDHC: 0
FSL_SDHC: 1
FSL_SDHC: 2 (eMMC)
u-boot=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe30000
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use PREBOOT as well. This allows a customer to just set fdt_board as
on any other module to customize the device tree for his carrier
board.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop optional support for the ancient Apalis iMX6 V1.0 hardware which
had the UART wired as DCE rather than DTE.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop legacy nfsboot script in favor of distroboot DHCP boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use the same name of DHCP Distroboot script as in regular eMMC case.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Include SCSI in the list of boot targets if CONFIG_CMD_SCSI is
enabled.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Drop legacy #define CONFIG_DRIVER_DM9000 from board include/configs/
and enable the same in Kconfig configs/ .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The IMX_FEC_BASE value is not used when CONFIG_DM_ETH is configured. So this
value can be removed.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update the 'boot_net' script to load the fdt with the kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since we envision using overlays for display interfaces, the video=
settings within vidargs are obsolete. Remove these settings from the
U-Boot.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
All the other NAND-based boards have tdxargs specified for setting
manual kernel command-line arguments.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The COUNTER_FREQUENCY is missed in 8ulp configs, it will cause SPL
and u-boot not set the cntfrq_el0. For u-boot, this is ok, because
ATF has set it. But for SPL, it will lead delay and get_timer
not working.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because the Beacon imx8mn board uses device tree
for MMC/SD and Ethernet, there is no need to have some of the
config options. It's handled by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Because the Beacon imx8mm board uses device tree
for MMC/SD and Ethernet, there is no need to have some of the
config options. It's handled by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Based on current usage, migrate a number of DP-DDR related options to
Kconfig.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform has CONFIG_ETH_DESIGNWARE set already, which is the
correct value for the driver in question. Remove this incorrect line.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move these two options to the arch Kconfig file.
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
This symbol is only possibly useful on some mvebu platforms, so move the
symbol there and select it for the only current user.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a little tricky since SoCFPGA has code to determine this as
runtime. Introduce a guard variable for platforms to select if they
have a static value to use. Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONS_SCIF0
CONFIG_CONS_SCIF1
CONFIG_CONS_SCIF2
CONFIG_CONS_SCIF4
CONFIG_CONS_SCIFA0
Signed-off-by: Tom Rini <trini@konsulko.com>
These values are only used in one file, reference them more directly.
Cc: Kamil Lulko <kamil.lulko@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This code is only used on the corvus platform, so migrate the LED on/off
code to this platform and remove it from the CONFIG namespace. In
theory, this should likely be moved to the modern GPIO LED driver as a
further cleanup.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
A number of CONFIG options are used on these platforms as part of the
default environment. Set some of these more directly and in other
cases, just reference them directly.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CM_INIT
CONFIG_CM_REMAP
CONFIG_CM_SPD_DETECT
CONFIG_CM_MULTIPLE_SSRAM
CONFIG_CM_TCRAM
We make the first three of these options be always enabled, as that
matches usage. We select the last two based on how they were defined in
armcoremodule.h. This also allows us to remove some unused code in
board/armltd/integrator/lowlevel_init.S
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is only enabled for CI_UDC and !TEGRA20, so implement it as
such in Kconfig directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
This converts the following to Kconfig:
CONFIG_BOARD_SIZE_LIMIT
To do this, introduce CONFIG_HAS_BOARD_SIZE_LIMIT.
Signed-off-by: Tom Rini <trini@konsulko.com>
Up till now the CONFIG_POWER_TPS65217 has been defined in several header
files for am335x SoC.
This patch renames it to CONFIG_PMIC_TPS65217, which better reflects the
role of this IC circuit.
Moreover, new CONFIG_PMIC_TPS65217 has been introduced in Kconfig
to be used with boards, which both support DM_PMIC and DM_I2C.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Migrate all other platforms as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
=HOoS
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- Rearrange defconfig option order
- Add CONFIG_SAVE_PREV_BL_* options
- Doc updates:
- remove wrong SBOOT memory corruption note, because
memory is changed during u-boot bringup process,
not by SBOOT
- put payload on ramdisk place in abl boot image
creation step
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- strip unneeded config options
- add FIT image support
- add framebuffer node, u-boot logo and video console
- increase LMB_MAX_REGIONS, to store all linux dtb reserved memory regions
- add linux kernel image header
Uart driver causes hang, when u-boot is used in android boot image instead
of linux. Temporary disable console driver, until investigated and fixed.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
We already support the NVMe commands and PCIe backend in the QEMU target,
so let's make it easy for anyone to consume them and enable NVMe distro
boot along the way!
With this patch, I can put an NVMe backed disk image into my QEMU VM and
have it automatically load a UEFI target blob.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] 5b70c1f679/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
This command's functionality is now completely implemented by the
standard fs load command. Convert the vexpress64 boot command (which is
the only user) and remove the implementation.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The ARMv8-R64 architecture introduces optional VMSA (paging based MMU)
support in the EL1/0 translation regime, which makes that part mostly
compatible to ARMv8-A.
Add a new board variant to describe the "BASE-R64" FVP model, which
inherits a lot from the existing v8-A FVP support. One major difference
is that the memory map in "inverted": DRAM starts at 0x0, MMIO is at
2GB [1].
* Create new TARGET_VEXPRESS64_BASER_FVP target, sharing most of the
exising configuration.
* Implement inverted memory map in vexpress_aemv8.h
* Create vexpress_aemv8r defconfig
* Provide an MMU memory map for the BASER_FVP
* Update vexpress64 documentation
At the moment the boot-wrapper is the only supported secure firmware. As
there is no official DT for the board yet, we rely on it being supplied
by the boot-wrapper into U-Boot, so use OF_HAS_PRIOR_STAGE, and go with
a dummy DT for now.
[1] https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[Andre: rebase and add Linux kernel header]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add MAINTAINERS entry for Peter]
In preparation for the ARMv8-R64 FVP support, which has DRAM mapped at
0x0, generalise the page table generation, by using symbolic names for
the address ranges instead of fixed numbers.
We already define the base of the DRAM and MMIO regions, so just use
those symbols in the page table description. Rename V2M_BASE to the more
speaking V2M_DRAM_BASE on the way.
On the VExpress memory map, the address space right after 4GB is of no
particular interest to software, as the whole of DRAM is mapped at 32GB
instead. The first 2 GB alias to the lower 2GB of DRAM mapped below 4GB,
so we skip this part and map some more of the high DRAM, should anyone
need it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far the FVP model just supports booting through semihosting, so by
loading files from the host the model is running on. This allows for
quick booting of new kernels (or replacing DTBs), but prevents more
featureful boots like using UEFI.
Enable the distro_boot feature, and provide a list of possible boot
sources that U-Boot should check:
- For backwards compatibility we start with semihosting, which gets its
commands migrated from CONFIG_BOOTCOMMAND into the distro_boot
infrastructure. This is also slightly tweaked to fail graceful in case
the required files could not be found.
- Next we try to use a user provided script, that could be easily
placed into memory using the model command line.
- Since we gained virtio support with the enablement of OF_CONTROL,
let's check virtio block devices next. This is where UEFI boot can
be easily used, for instance by providing a distro installer .iso
file through virtio-blk.
- Networking is now provided by virtio as well, so enable the default
PXE and DHCP boot flows, mostly because we can.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The definition of the standard environment variables (kernel_addr_r and
friends) has been improved lately for the FVP model, but the Juno board
is still using some custom scheme.
Since we need to extend this to a third board soon, let's unify the
definition:
- Define the Juno addresses in the same generic way we do for the FVP
model, and move the actual variable setting out of the board #ifdef's.
- Add the missing addresses for a PXE file and a boot script.
- Cleanup some stale comments on the way.
As the FVP model doesn't have support for distro_boot quite yet, add
a dummy definition for now, to be replaced with the real thing later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE
Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NORFLASH_PS32BIT
Note that we also attempt to correct the behavior of the code here,
which had been testing for "NORFLASH_PS32BIT" which would never be set,
instead check for the now set "CONFIG_NORFLASH_PS32BIT", which results
in some behavior change.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_USE_NANDFLASH and CONFIG_SYS_USE_MMC serve the
same purpose as CONFIG_SD_BOOT / CONFIG_NAND_BOOT so migrate to using
these switches instead as they're already in Kconfig.
Cc: Stelian Pop <stelian@popies.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of M5373EVB we always had NANDFLASH_SIZE=16, so just use it
directly. In the case of M5329EVB we had not removed the rest of NAND
support when saying we didn't have NAND, so instead use that to key off
of rather than NANDFLASH_SIZE.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The value CONFIG_DB_784MP_GP is only used in the DDR code to refer to
CONFIG_TARGET_DB_MV784MP_GP so just use that second value directly.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We only set one of these values ever at this point, so remove dead code.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
There are a handful of variants around CONFIG_SYS_USE_DATAFLASH and none
of them now control anything further within their board config.h files,
so remove these from CONFIG_SYS_EXTRA_OPTIONS and then remove the empty
blocks in the board config.h files. In a few places further clean up
related logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LPUART
CONFIG_LPUART_32B_REG
And note that CONFIG_LPUART_32B_REG is unused in code.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one place, so pick a more direct name and
migrate to Kconfig. Rework the code slightly.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MCFRTC
CONFIG_SYS_MCFRTC_BASE
While at it, remove '#undef RTC_DEBUG' from these config files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Both of these variables are used in a few hard-coded ways to set some
string values or print something to the user. In almost all cases, it's
just as useful to hard-code the value used. The exception here is
printing something closer to correct board name for p1_p2_rdb machines.
This can be done using something from the device tree, but for now
hard-code a non-CONFIG based value instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTM_NETBSD
CONFIG_BOOTM_RTEMS
CONFIG_DESIGNWARE_WATCHDOG
CONFIG_DISPLAY_CPUINFO
CONFIG_DM_ETH
CONFIG_DM_MMC
CONFIG_DM_REGULATOR
CONFIG_DM_SPI
CONFIG_DM_SPI_FLASH
CONFIG_ISO_PARTITION
CONFIG_OF_SEPARATE
CONFIG_SPI_FLASH_WINBOND
CONFIG_SPL_ETH
CONFIG_TIMER
CONFIG_USB_DWC3
CONFIG_USB_DWC3_GADGET
CONFIG_USB_DWC3_OMAP
CONFIG_USB_DWC3_PHY_OMAP
CONFIG_USB_EHCI_TEGRA
CONFIG_USB_GADGET_DOWNLOAD
CONFIG_USB_GADGET_DUALSPEED
CONFIG_USB_GADGET_MANUFACTURER
CONFIG_USB_GADGET_PRODUCT_NUM
CONFIG_USB_GADGET_VBUS_DRAW
CONFIG_USB_GADGET_VENDOR_NUM
This catches a number of cases where board config files were #undef
various CONFIG options when building SPL, and that doesn't work. Clean
up the related comments as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The SPL does not update the memory node with the dram size from EEPROM
but instead we can use get_ram_size which does a simple memory test
to determine the available RAM. Update PHYS_SDRAM_SIZE to 4GiB as that
is the max used on the Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The 2x256 MiB SF variant of this system has 192 MiB rootfs MTD partition
containing UBI on SF0, use the correct size in U-Boot environment, else
U-Boot cannot mount UBI and boot on this variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VIDEO_BCM2835
This is the final ad-hoc CONFIG_VIDEO_... to convert.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FAULT_ECHO_LINK_DOWN
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91_WANTS_COMMON_PHY
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LEGACY
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91_GPIO_PULLUP
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This variable is used once and is noted as board-specific. Use the
value directly with a comment.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is used only once, and in comparison with an unset symbol,
so drop it.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G10EK
CONFIG_AT91SAM9261EK
CONFIG_AT91SAM9G10
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G20EK
CONFIG_AT91SAM9260EK
CONFIG_AT91SAM9G20EK_2MMC
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AM335X_USB0
CONFIG_AM335X_USB0_MODE
CONFIG_AM335X_USB1
CONFIG_AM335X_USB1_MODE
We do this by introducing specific options for static configuration of
USB0/USB1 in SPL rather than defining CONFIG_AM335X_USBx_MODE to the
enum value being used. Furthermore, with how the code is used now we do
not need to have OTG mode exposed as an option here, so remove that.
Signed-off-by: Tom Rini <trini@konsulko.com>
With all boards now using DM_ETH we determine the value for
CONFIG_FEC_XCV_TYPE at run time, except in the case of the default
fall-back. Set the fallback directly now.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ETHPRIME
This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME
similar to other options that are not always set and control environment
variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts removes the following symbols:
CONFIG_HAS_ETH0
CONFIG_HAS_ETH1
CONFIG_HAS_ETH2
CONFIG_HAS_ETH3
This is because at this point, only the ids8313 platform was using the
code which was controlled by these symbols. In turn, this code already
performs error checking on being able to perform the device tree fixup.
Rather than convert these to Kconfig for a single platform, update the
code to not need these checks and remove them from all the platforms
they were unused on.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOT_RETRY_TIME
CONFIG_BOOT_RETRY_MIN
CONFIG_RESET_TO_RETRY
We also introduce CONFIG_BOOT_RETRY to gate these options, and clean up
the associated Makefile entry and C code for picking default values of
CONFIG_BOOT_RETRY_MIN.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ARMV8_SWITCH_TO_EL1
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
This converts the following to Kconfig:
CONFIG_ARMV7_SECURE_BASE
CONFIG_ARMV7_SECURE_MAX_SIZE
CONFIG_ARMV7_SECURE_RESERVE_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
As the CI test for stopping platforms from being merged that were
defining symbols that had Kconfig entries, a small number of symbols
needed to be migrated again. Do so, and catch two cases the README
should also have been updated but was not.
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit re-introduced a migrated CONFIG symbol to the board header
file. These changes should likely be handled via documentation instead,
as well.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We cannot define a CONFIG value here to ensure that the Kconfig value
isn't set wrong.
Fixes: 2c699fe0d3 ("configs: sunxi: Add common SUNIV header")
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch enables some configs that should be working on the Bob board,
based on what is observed to work on the Kevin board.
The Bob board uses an Embedded DisplayPort panel compatible with the
simple panel and Rockchip eDP drivers. Its backlight is controlled by
the Chromium OS Embedded Controller Pulse Width Modulator. Enable these
for the board.
Also set VIDEO_ROCKCHIP_MAX_{XRES,YRES} to 1280x800, the resolution of
its panel. This had to be done for the Kevin board, but it's untested if
this is actually necessary for Bob.
The Rockchip video driver needs to assert/deassert some resets, so also
enable the reset controller. RESET_ROCKCHIP defaults to y for this board
when DM_RESET=y, so it's enough to set that.
The Bob board has two USB 3.0 Type-C ports and one USB 2.0 Type-A port
on its right side. Enable the configs relevant to USB devices so these
can be used. This is despite a known issue with RK3399 boards where USB
de-init causes a hang, as there is a known workaround.
Some other rk3399-based devices enable support for the SoC's random
number generator in commit a475bef534 ("configs: rk3399: enable rng on
firefly/rock960/rockpro64"), as it can provide a KASLR seed when booting
using UEFI. Enable it for Bob as well.
The default misc_init_r() for Rockchip boards sets cpuid and ethernet
MAC address based on e-fuse block. A previous patch extends this on Gru
boards to set registers related to SoC IO domains as is necessary on
these boards. Enable this function and configs for it on Bob.
The microSD card slot on this board (and others based on Gru) is
connected to a GPIO controlled regulator (ppvar-sd-card-io), which must
be operable by U-Boot. Enable the relevant config option to allow this.
Bob boards also use the Winbond W25Q64DW SPI flash chip, enable support
for Winbond SPI flash chips in the board config so U-Boot can boot with
this chip.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
QSGMII PHY initialization should only be done for J721E EVMs and not for
J721E-SK boards. Therefore, fix the environment variables accordingly.
Also, by default remote processors should not be booted in U-Boot but
rather be left to the users to enable this by setting dorprocboot.
Therefore, remove dorprocboot that is being set by default.
Fixes: 5980925e2a ("include: configs: j721e_evm: Add support to boot ethfw core in j721e")
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Mechanically convert video_hw_init() function to UCLASS_VIDEO probe
callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.
As framebuffer base address is setup by the bootloader which loads U-Boot,
set plat->base to that fixed framebuffer address.
This change was tested in qemu n900 machine and is working fine.
What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.
Signed-off-by: Pali Rohár <pali@kernel.org>
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Currently, any u-boot bootloader for ti armv7 platforms using
DEFAULT_FIT_TI_ARGS to boot with a fitimage (boot_fit = 1)
doesn't boot when built with Yocto Poky (openembedded-core).
## Loading kernel from FIT Image at 90000000 ...
Could not find configuration node
ERROR: can't get kernel image!
Arago forked the kernel-fitimage class [1] and altered the
configuration nodes naming while adding the OPTEE support by
using FITIMAGE_CONF_BY_NAME by default [2].
The "upstream" kernel-fitimage class from openembedded-core still
add the "conf-" prefix for each configuration nodes [3].
The ITS file format (from doc/uImage.FIT/source_file_format.txt)
is not really accurate with the expected naming of these nodes.
But in practice the "conf-" prefix is widely used.
When the FIT image support has been added for ti armv7 platforms
the naming from Arago has been used [3]. Fix this issue by adding
the prefix expected by the ITS file generated by kernel-fitimage
class from openembedded-core.
[1] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=719ab1b2098bcdc59c249e3529fa82cb1b9130e6
[2] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=f23f2876a0cda89241d031bb7ba0b4256ed90035
[3] https://git.openembedded.org/openembedded-core/tree/meta/classes/kernel-fitimage.bbclass?h=yocto-3.1.13#n290
[3] 1e93cc8473
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Denys Dmytriyenko <denys@konsulko.com>
This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These particular values are not configurable and today we always set
CONFIG_SECURE_BL1_ONLY. Move these to where they're used in the code,
and drop from the CONFIG namespace.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Remove some code, primarily CPM2 related, that is now unused since the
removal of MPC8540/60ADS.
Fixes 3913191c8a ("powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().
Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The BOOT_TARGET_DEVICES list for distro_bootcmd was hard-coded to assume
that all boot devices are available/enabled in the configuration,
thus ignoring the actual config settings. The config_distro_bootcmd.h
header file specifically has compile-time checks to detect such problems.
To allow disabling USB, SCSI, etc. in custom lx2160a board configs,
make it depend on the config settings and use only the enabled features.
Signed-off-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Use the complete 512kb (4 blocks) nand partition reserved for u-boot
environment instead of just the first block, this allows the module to
have a working environment even if 3 blocks are bad.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Now that single defconfig can be used for booting J721E EVM and
SK, default device tree will not work for selecting dtb for
kernel. Update the findfdt env to select right dtb based on
board_name env variable.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
There are no boards that define CONFIG_SYS_RESET_ADDR, so drop the
remaining comments referencing it and also the config_whitelist.txt entry.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: thomas@wytron.com.tw
This driver adds support for the keyboard on Apple Silicon laptops.
The controller for this keyboard sits on an SPI bus and uses an
Apple-specific HID over SPI protocol. The packets sent by this
controller for key presses and key releases are fairly simple and
are decoded directly by the code in this driver and converted into
standard Linux keycodes. The same controller handles the touchpad
found on these laptops. Packets for touchpad events are simply
ignored.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert
to Driver Model and use uclass mvgbe and the compatible driver M88E1118R
to bring up Ethernet.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- As the result of the migration to Driver Model, this u-boot image has
grown substantially (about 100K, give or take). The old envs location
at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K).
- Miscellaneous changes: Move constants to .c file and remove header file
board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to
keep u-boot image under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Dockstar board has the network chip Marvell 88E1116R. Convert to
Ethernet driver model, and use uclass mvgbe and the compatible driver
M88E1118R to bring up Ethernet.
- Add CONFIG_DM_ETH and associated configs.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Add CONFIG_PHY_MARVELL to properly configure the network.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Miscellaneous changes: Move constants to .c file and remove
header file board/Seagate/dockstar/dockstar.h, use
CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, add CONFIG_HUSH_PARSER, use BIT macro, and cleanup comments.
- Note: This patch is a RESEND for a previous patch:
https://patchwork.ozlabs.org/project/uboot/patch/20210812051854.1340-2-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Miscellaneous changes: Move constants to .c file and remove header file
board/iomega/iconnect/iconnect.h. Add CONFIG_HUSH_PARSER, use BIT macro,
and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Globalscale Technologies Dreamplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network
port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned,
could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/dreamplug/dreamplug.h, cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE
Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is defined based on two other CONFIGs for all boards except sandbox
and durian.
For sandbox the value does not matter. For durian the value seems
excessive.
Drop the option completely, to simplify configuration and reduce the
number of things we need to convert to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_IDE_MAXBUS
CONFIG_SYS_IDE_MAXDEVICE
CONFIG_SYS_ATA_BASE_ADDR
CONFIG_SYS_ATA_STRIDE
CONFIG_SYS_ATA_DATA_OFFSET
CONFIG_SYS_ATA_REG_OFFSET
CONFIG_SYS_ATA_ALT_OFFSET
CONFIG_SYS_ATA_IDE0_OFFSET
CONFIG_SYS_ATA_IDE1_OFFSET
CONFIG_ATAPI
CONFIG_IDE_RESET
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move setting the default boot command to the
apalis/colibri_imx6_defconfig. It allows replacing the command
without code modification.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The Linux Kernel Image size for arm64 is still growing.
A Kernel with 54 MB at load address 0x80280000 overlaps
with fdt_addr at 0x83000000. So let's increase it to 0x84000000
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Commit 72d81360aa ("global: Convert CONFIG_LOADADDR to
CONFIG_SYS_LOADADDR") dropped the usage of LOADADDR and replaced it with
SYS_LOADADDR.
Use the correct macro in environment by replacing CONFIG_LOADADDR with
CONFIG_SYS_LOADADDR.
Fixes: d75ebf3482 ("imx: ventana: fix splash logo drawing")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Add fdt_addr_r fdtfile which used by distro boot, and cleanup legacy
environment variables.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
We changed to single flash.bin now. So dfu_alt_info should be modified
to reflect this change.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The PDK2 board is capable of running both 100M and 1G ethernet. However,
the i.MX6 has only one ethernet MAC, so it is possible to configure
either 100M or 1G Ethernet. In case of 100M option, the PHY is on the
SoM and the signals are routed to a RJ45 port. For 1G the PHY is on
the PDK2 board with another RJ45 port. 100M and 1G ethernet use
different signal pins from the i.MX6, but share the MDIO bus.
This SoM board combination is used to demonstrate how to enable 1G
ethernet configuration.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Use the complete 512kb (4 blocks) nand partition reserved for u-boot
environment instead of just the first block, this allows the module
to have a working environment even if 3 blocks are bad.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Adds support for SUNIV and the F1C100s.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Remove some pointless #ifdefs from this file, as there are quite too
many of them already.
Some definitions don't really hurt to have in any case, so remove the
pointless CONFIG_MMC guard around CONFIG_MMC_SUNXI_SLOT.
The BOARD_SIZE_LIMIT applies regardless of ARM64 or not (now), so remove
that guard as well. The maximum number of MMC devices does not depend on
CONFIG_ENV_IS_IN_MMC, so move that out to simplify the file.
Last but not least CONFIG_SPL_BOARD_LOAD_IMAGE serves no real purpose
anymore: it's unconditionally defined for all sunxi boards, and protects
nothing applicable outside of sunxi code anymore. Just remove it.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Field fail-safe u-boot update procedure for pg-wcom boards is defined and
implemented by patch: 59b3403.
This patch invokes the update procedure for pg-wcom-ls102x designs during
early misc_init_f execution.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The GoFlex Home board has the network chip Marvell 88E1116R.
Use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: use CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
With Ethboot support in SPL, network stack requires more BSS area, so
increase BSS max size to 16K
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Today the bootcount is not managed by the Linux kernel for STM32MP15 as
we don't have driver to update the used backup register in TAMP and the
recovery command still executes the normal bootcmd with
'altbootcmd=run bootcmd'.
So the bootcount feature is never used, the config CONFIG_BOOTCOUNT_LIMIT
and the associated environment variable 'altbootcmd' can be removed to
reduce the U-Boot size.
Each boards can re-enable this feature later in their defconfig, if it is
needed, with the expected backend, for example CONFIG_BOOTCOUNT_GENERIC
or CONFIG_BOOTCOUNT_ENV.
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the following to Kconfig:
CONFIG_AT91_EFLASH
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Prepare migration to Kconfig.
CONFIG_SYS_MAX_FLASH_BANKS_DETECT becomes boolean and
CONFIG_SYS_MAX_FLASH_BANKS define the MAX size, also used
for detection when CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
(CFI_MAX_FLASH_BANKS = CONFIG_SYS_MAX_FLASH_BANKS).
CONFIG_SYS_MAX_FLASH_BANKS become mandatory when
CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
The am335x-ice-v2 board's Ethernet ports can be configured
in 'MII' or 'RMII' mode to be connected to 'PRUSS' or 'CPSW'
Ethernet subsystems.
This patch sets the environment variable 'ice_mii' to
'mii' or 'rmii' accordingly. Based on that we choose the
appropriate board devicetree i.e. 'am335x-ice-v2.dtb' or
'am335x-ice-v2-prueth.dtb'.
Since there are 2 Ethernet ports with 2 modes, there can be 4
configurations but for now we consider both ports in different modes
to be an invalid configuration and prevent boot in that case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Amjad: use overlay instead of using new am335x-ice-v2-prueth.dtb]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make prueth_is_mii be marked __maybe_unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
BOOT_TARGET_DEVICES should only be added if the corresponding u-boot
command is enabled otherwise the build will fail.
Signed-off-by: Piotr Kubik <piotr_kubik@vp.pl>
These hardcoded values were calculated from CONFIG_SPL_TEXT_BASE macro. Now
this macro is configurable via Kconfig, so calculate values 0x0030/0x4030
at compile time via CONFIG_SPL_TEXT_BASE option. Values 0x0030/0x4030
represents offset of CONFIG_SPL_TEXT_BASE from address 0x40000000.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Memory layout in the comment is from Armada XP platform which uses load
address 0x40004030. DB-88f6720 is Armada 375 platform which uses same load
address as Armada 38x which is 0x40000030.
Currently SPL support for Armada 375 is unfinished and does not work. There
is missing Serdes initialization and DDR3 training code. So nobody noticed
that CONFIG_SPL_* options are not correct.
Fix at least CONFIG_SPL_TEXT_BASE constant and remove incorrect comments
about memory layout. So it is not misleading.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
After the conversion to DM the SD card shows up as 'mmc 2'
device.
Adjust the 'mmcdev' and the distro command 'func' accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Enable support for USB and USB storage on the UDOO Neo.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In AOSP, both VIM3 and VIM3L have 2 bootloader flavors,
depending on A/B enablement.
For example, for vim3l, the naming is:
- u-boot_kvim3l_noab.bin : legacy support
- u-boot_kvim3l_ab.bin : A/B support
Prepare a defconfig to support u-boot_kvim3_ab.bin and
u-boot_kvim3l_ab.bin.
This is identical to khadas-vim3{l}_ab_android but will be updated in
the next commit.
Also update partitioning tables for A/B support.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-4-mkorpershoek@baylibre.com
This allows us to define extra board variables, such as "board" and
"board_name".
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-2-mkorpershoek@baylibre.com
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-7-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze is one the last two users of the CONFIG_SYS_RESET_ADDRESS
macro (the other is arch/powerpc/cpu/mpc8xx/cpu.c, but the macro is not
defined anywhere in powerpc code, so it should be removed there too).
Replace CONFIG_SYS_RESET_ADDRESS usage in start.S with
CONFIG_SYS_TEXT_BASE. If the reset address should really be
user-configurable, a new Kconfig option could be added.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-6-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The memory layout is taken from the device tree passed to us by
m1n1, so there is no need to define this.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The SMSC driver is using the old driver model.
Init the virtio system in vexpress64.c so that the network device is
discovered.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Move env var address values to #defines so they can be reused elsewhere.
Rename env var names to those recommended in the README and modify
addresses to allow more space for the kernel.
Fix issue where fdt is called with invalid arguments when booting
without a ramdisk.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Rename from vexpress_aemv8a.h -> vepxress_aemv8.h as new FVPs may not be
v8-A. No change in behavior.
This is towards future work to enable support for the FVP_BaseR.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
When using a recent kernel with a bunch of compiled-in
stuff the kernel image easily becomes bigger than 8 MB
yielding this error:
Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Fix this by bumping to SZ_64MB.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
-----BEGIN PGP SIGNATURE-----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=YdSB
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request of efi-next
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
This converts the following to Kconfig:
CONFIG_JFFS2_DEV
CONFIG_JFFS2_LZO
CONFIG_JFFS2_NAND
CONFIG_JFFS2_PART_OFFSET
CONFIG_JFFS2_PART_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_88F5182
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_IS_OPENRD_CLIENT
CONFIG_BOARD_IS_OPENRD_ULTIMATE
CONFIG_D2NET_V2
CONFIG_FEROCEON
CONFIG_FEROCEON_88FR131
CONFIG_INETSPACE_V2
CONFIG_KW88F6192
CONFIG_KW88F6281
CONFIG_KW88F6702
CONFIG_NET2BIG_V2
CONFIG_NETSPACE_LITE_V2
CONFIG_NETSPACE_MAX_V2
CONFIG_NETSPACE_MINI_V2
CONFIG_NETSPACE_V2
CONFIG_SHEEVA_88SV131
At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.
Signed-off-by: Tom Rini <trini@konsulko.com>
The only place we use CONFIG_CPU_ARMV8 was in the arm_dcc serial driver.
Switch this to CONFIG_ARM64 today, and if in the future we need finer
granularity tuning here, a new CONFIG_SERIAL option needs to be
introduced.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one of two ways. The first way is that it
is defined to a static value, of an unsigned long size. The second way
is that it is defined to something, typically a function, to determine
this value at run time.
However, in a few cases that function returns a static value. Change
that to using the static value directly.
In the case of using something at run time, convert everything to using
a function of the same name and prototype. This will allow for further
cleanups.
Finally, we have a few cases where the function is just not used, so
drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_CLK_FREQ_C100 and CONFIG_SYS_CLK_FREQ_C110 are
only used in one place and not changed by the board config file. Move
these out of the CONFIG namespace and in to the CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
