This is only used on sandbox, so select it there.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the SRIO namespace do not
easily transition to Kconfig. In many cases they likely should come from
the device tree instead. Move these out of CONFIG namespace and in to
CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SRIO1
CONFIG_SRIO2
CONFIG_SRIO_PCIE_BOOT_MASTER
CONFIG_SYS_SRIO
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_TIMER_COUNTS_DOWN
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_NOBQFMAN
CONFIG_SYS_DPAA_DCE
CONFIG_SYS_DPAA_FMAN
CONFIG_SYS_DPAA_PME
CONFIG_SYS_DPAA_RMAN
CONFIG_SYS_PMAN
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_PCI and
CONFIG_SYS_PCIE namespace do not easily transition to Kconfig. In many
cases they likely should come from the device tree instead. Move these
out of CONFIG namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_OMAP_ABE_SYSCK
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NUM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SPL_NS16550_MIN_FUNCTIONS
CONFIG_SYS_NS16550_MEM32
CONFIG_SYS_NS16550_PORT_MAPPED
CONFIG_SYS_NS16550_REG_SIZE
CONFIG_SYS_NS16550_SERIAL
To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that
platforms can enable the legacy driver here for SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the callback function we have to use memcpy(). Otherwise we add
the new samples on top of what is stored in the stream buffer.
If we don't have enough data, zero out the rest of the stream buffer.
Our sampling frequency is 48000. Let the batch size for the callback
function be 960. If we play a multiple of 20 ms, this will always be
a full batch.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Consider unexpected values for frequency:
* negative frequency
* zero frequency
* frequency exceeding sampling frequency
As in these cases the sum of the samples is zero also check the count of
the samples.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ZynqMP mini configurations are not using IPI driver and enabling this is
adding additional ~1200 Bytes (depends on configuration).
This ends up in situation that there is no enough space in OCM for
relocation that's why disable this driver for all mini configurations.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c71bab3927cb71ae517d9c21f59f3d5cf0caf712.1669734580.git.michal.simek@amd.com
The commit ed35de6170 ("Convert CONFIG_ZYNQMP_PSU_INIT_ENABLED to
Kconfig") converted CONFIG_ZYNQMP_PSU_INIT_ENABLED symbol and enabled it by
default which is not correct configuration.
Intention of this config was to have it enabled by default for SPL and
provide an option to users to also do low level initialization directly
from U-Boot.
That's why it is necessary to define second symbol with SPL marking in it
and properly use symbols depends on usage in Makefile.
Also disable ZYNQMP_PSU_INIT_ENABLED from boards which enables it by
default. CONFIG_SPL_ZYNQMP_PSU_INIT_ENABLED is enabled by default when SPL
is enabled.
Reported-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d5fcbd66b05bf0d7ef594e66464ee23b48c5e4cc.1669969083.git.michal.simek@amd.com
When Linux boot takes over control of the pmu
(by signaling PM_INIT_FINALIZE via ipi), pmu will switch off 'unused'
rpu cores. The Xilinx zynqmp fsbl prevents switching off those cores by
marking rpu cores as 'used' when loading code partitions to those cores.
The current u-boot SPL is missing this behaviour, which results in
halting rpu cores during Linux boot.
This commit mimics the xilinx zynqmp fsbl behavior by marking r5 cores as
used when they are released during boot.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Signed-off-by: Lukas Funke <lukas.funke-oss@weidmueller.com>
Link: https://lore.kernel.org/r/20221028121547.26464-2-lukas.funke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The SanCloud BBE requires the same dtb nodes to be present in the SPL as
the AM335x EVM.
The SanCloud BBE Lite also requires the SPI flash node and all
dependencies to be present in the SPL to support SPI boot.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
For successful boot when CONFIG_SPL_OF_CONTROL=y, we need to ensure that
the board EEPROM on i2c0, the uart0 serial port and the relevant boot
device (mmc1 or mmc2) can be accessed in the SPL. We also need to
preserve the parent nodes for each required dtb node.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The signal name of pin PD8 with function D is A22_NANDCLE
as it is defined in the datasheet.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Use macro to represent the RL and WL setting to ensure the PHY and
controller setting are aligned.
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
- Re-add the old PHY reset binding for nanopi-k2
-----BEGIN PGP SIGNATURE-----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=yEaP
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20221122' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Implement setbrg op to meson serial device
- Re-add the old PHY reset binding for nanopi-k2
The sync of device-tree/bindings in 11a48a5a18c6 ("Linux 5.6-rc2") causes
Ethernet to break on some GXBB boards; the PHY seems to need proper reset
timing to function in u-boot and Linux. Re-add the old PHY reset binding
for dwmac until we support new bindings in the PHY node. This borrows the
same fix applied to the Odroid C2 board [0].
[0] https://lists.denx.de/pipermail/u-boot/2021-April/446658.html
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20221025143205.14470-1-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support octal spi flash and uses DCC terminal
for console output. Add required dts for octal spi flash mini u-boot
configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support qspi flash and uses DCC terminal
for console output. Add required dts files for qspi mini configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add soc_xilinx_versal_net driver to identify the family & revision of
versal-net SoC. Add Kconfig option CONFIG_SOC_XILINX_VERSAL_NET to
enable/disable this driver. To enable this driver by default, add this
config to xilinx_versal_net_virt_defconfig file. This driver will be
probed using platdata U_BOOT_DEVICE structure which is specified in
mach-versal-net/cpu.c.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/613d6bcffd9070f62cf348079ed16c120f8fc56f.1668612993.git.michal.simek@amd.com
The fclk-enable property is set to 0 which disables all FCLKs.
Enable all FCLKs so they can be used as clock sources in the
programmable logic.
Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b1308dc1f14f8eb24662019f7376c959e5e763b8.1665567031.git.michal.simek@amd.com
Removing the zynq_board_read_rom_ethaddr() function as
xlnx,eeprom is not used anymore. As all board dts to use
nvmem alias instead of xlnx,eeprom.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221017094818.17996-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Apply commit 534f0fbd65 ("arm64: Fix relocation of env_addr if
POSITION_INDEPENDENT=y") also for 32-bit ARM.
This change fixes crashing of U-Boot on ARMv7 (Omap3 / Cortex-A8) Nokia N900
phone (real HW). Note that qemu emulator of this board with same u-boot.bin
binary has not triggered this crash.
Crash happened after U-Boot printed following debug lines to serial console:
initcall: 0001ea8c (relocated to 8fe0aa8c)
Loading Environment from <NULL>... Using default environment
Destroy Hash Table: 8fe25a98 table = 00000000
Create Hash Table: N=387
Signed-off-by: Pali Rohár <pali@kernel.org>
Describe that CONFIG_SBI_V02=y does not mean SBI specification v0.2
but v0.2 or later.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We should check the string until it hits underscore, in case it
searches multi-letter extensions. For example, "rv64imac_xandes"
will be treated as D extension support since there is a "d" in
"andes", resulting illegal instruction caused by initializing FCSR.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The initial devicetree for PolarFire SoC incorrectly created a fixed
frequency clock in the devicetree to represent the msspll, but the
msspll is not a fixed frequency clock. The actual reference clock on a
board is either 125 or 100 MHz, 125 MHz in the case of the icicle kit.
Swap the incorrect representation of the msspll out for the actual
reference clock.
Fixes: dd4ee416a6 ("riscv: dts: Add device tree for Microchip Icicle Kit")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
We should guard the SPL nodes against CONFIG_SPL_BUILD to fix
the following build error when the blobs are absent:
binman: Fail open first container file mx8qm-ahab-container.img
Signed-off-by: Fabio Estevam <festevam@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_NONCACHED_MEMORY
To do this we introduce CONFIG_SYS_HAS_NONCACHED_MEMORY as a bool to
gate if we are going to have noncached_... functions available and then
continue to use CONFIG_SYS_NONCACHED_MEMORY to store the size of said
cache. We make this new option depend on both the architectures which
implement support and the drivers which make use of it.
Cc: Tom Warren <twarren@nvidia.com>
Cc: Mingming lee <mingming.lee@mediatek.com>
Cc: "Ying-Chun Liu (PaulLiu)" <paul.liu@linaro.org>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These files reference SZ_ macros without including <linux/sizes.h>,
correct this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce three options, one for each observed L3 cache size, and have
the size select'd as needed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce two options, one for each observed L2 cache size, and have the
size select'd as needed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_INIT_RAM_LOCK
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Switch to use binman to pack images
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Originally, the mmc aliases node was present in imx6qdl-wandboard.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a regression in which the SD card cannot be found anymore:
Since commit the aliases node has been removed
U-Boot 2022.10-00999-gcca41ed3d63f-dirty (Nov 03 2022 - 22:07:38 -0300)
CPU: Freescale i.MX6QP rev1.0 at 792 MHz
Reset cause: POR
DRAM: 2 GiB
Core: 62 devices, 17 uclasses, devicetree: separate
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the SD card (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Note: Nowadays, the intent is for them regular device trees to just be
synchronised from them Linux kernel device trees and any and all U-Boot
specific changes need to go into the -u-boot.dtsi device tree include
files which BTW get included automatically by the U-Boot build system.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Migrate to using automatic build system included -u-boot.dtsi device
tree include files.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Add support for the MSC SM2S-IMX8PLUS SMARC Module. Tested in conjunction
with the MSC SM2-MB-EP1 Mini-ITX Carrier Board.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Update the sandbox implementation to use UCLASS_HOST and adjust all
the pieces to continue to work:
- Update the 'host' command to use the new API
- Replace various uses of UCLASS_ROOT with UCLASS_HOST
- Disable test_eficonfig since it doesn't work (this should have a unit
test to allow this to be debugged)
- Update the blk test to use the new API
- Drop the old header file
Unfortunately it does not seem to be possible to split this change up
further.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running unit tests, some may have side effects which cause a
subsequent test to break. This can sometimes be seen when using 'ut dm'
or similar.
Add a new argument which allows a particular (failing) test to be run
immediately after a certain number of tests have run. This allows the
test causing the failure to be determined.
Update the documentation also.
Signed-off-by: Simon Glass <sjg@chromium.org>
In order to boot over USB, the device tree needs to enable
a few extra nodes in SPL. Since the USB driver has the
ability to detect host/device, the dr_mode can be removed
from the device tree since it needs to act as a device when
booting and OTG is the default mode. Add USB boot support
to spl_board_boot_device and enable the corresponding config
options.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The e10133 workaround was broken in two places:
- The code intended to temporarily mask all interrupts in GPC_IMRx_CORE0.
While the old register values were saved, the actual masking was
missing.
- imx_udelay() expects the system counter to run at its base frequency,
but the system counter is switched to a lower frequency earlier in
psci_system_suspend(), leading to a much longer delay than intended.
Replace the call with an equivalent loop (linux-imx 5.15 does the same)
This fixes the SoC hanging forever when there was already a wakeup IRQ
pending while suspending.
Fixes: 57b620255e ("imx: mx7: add system suspend/resume support")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
This enables armv8 crypto extension usage for SHA1/SHA256.
Which speed up sha1/sha256 operations, about 10x faster with
a imx8mm evk for a 20MiB kernel hash verification (12ms vs 165ms).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The RD-AC5X-32G16HVG6HLG-A0 development board main components and
features include:
* Main 12V/54V power supply
* 270 Gbps throughput packet processor on the main board
* DDR4:
* SR1: 2GB DDR4 2400MT/S(1GB x 2 pcs ) with ECC(1GB x 1 pcs)
* SR2: 4GB DDR4 2400MT/S(2GB x 2 pcs ) with ECC(2GB x 1 pcs)
* PCB co-layout with 4GB device to support 8GB (Dual CS) requirement
* 16GB eMMC (Samsung KLMAG1JETD-B041006)
* 16MB SPI NOR(GD25Q127C)
* 32 x 1000 Base-T interfaces
* 16 x 2500 Base-T interfaces
* SR1: 88E2540*4
* SR2: 88E2580*1+88E2540*2
* Six (6) x 25G Base-R SFP28 interfaces
* One (1) x RJ-45 console connector, interfacing to the on board UART
* One (1) x USB Type-A connector, interfacing to the USB 2.0 port (0)
* One (1) x USB Type-mini B connector, interfacing to the USB 2.0 port (1)
* One (1) x RJ-45 1G Base-T Management port, interfacing to the host
port (shared with PCIe) Connected to 88E1512 Gigabit Ethernet Phy
* One (1) x Oculink port, interfacing to the PCIe port for external CPU
connection
* POE 802.3AT support on Port 1 ~ Port 32, 802.3BT support on Port 33 ~
Port 48 (Microsemi PD69208T4, PD69208M or TI TPS2388,TPS23881
solution)
* POE total power budget 780W
* LED interfaces per network port/POE
* LED interfaces (common) showing system status
* PTP TC mode Supported (Reserved M.2 connector to support BC mode)
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
an integrated CPU (referred to as the CnM block in Marvell's
documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
has been ported from Marvell's SDK which is based on a much older
version of U-Boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The 64-bit mvebu SoCs don't have a suitable timer driver so add a !ARM64
condition to the select.
Fixes: 7b530bb19e ("arm: mvebu: Use CONFIG_TIMER on all MVEBU & KIRKWOOD platforms")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The uart1 node was missing the 'clock-frequency' property. This meant
the driver for this device would fail at probe.
The clock for uart1 is fed from the same source as uart0 and is a fixed
200MHz clock. This is confirmed via documentation for the CN9130 SoC
and from the equivalent code in Linux at:
<linux>/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
where uart0 and uart1 share a common 'clocks' definition.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add QSPI NAND device node to the Microchip PolarFire SoC
Icicle kit device tree.
The Winbond NAND flash memory can be connected to the
Icicle Kit by using the Mikroe Flash 5 click board and
the Pi 3 Click shield.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
In the v2022.10 Icicle reference design, the seg registers have been
changed, resulting in a required change to the memory map.
A small 4MB reservation is made at the end of 32-bit DDR to provide some
memory for the HSS to use, so that it can cache its payload between
reboots of a specific context.
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
As PLICSW is used to trigger the software interrupt, we should rename
Andes PLIC configuration and file name to reflect the usage. This patch
also updates PLMT and PLICSW compatible strings to be consistent with
OpenSBI fdt driver.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_SYS_MIPS_TIMER_REQ
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Resolve all uses of CONFIG_SYS_MHZ with the currently defined value.
Remove code which depends on CONFIG_SYS_MHZ but where no board configs
actually use that code.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add the needed bus mappings for the two main RTI memory ranges and
the required device tree nodes in the main domain.
Same as kernel commit 6dd8457dc20693e2ba9054c171499b22664fd4e7
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
So far the Calxeda machines were using the CONFIG_SYS_TIMER_* macros to
simply hardcode the address of the counter register of the SP804 timer.
This method is deprecated and scheduled for removal.
Use the newly introduced SP804 DM_TIMER driver to provide timer
functionality on Highbank and Midway machines. The base address and base
frequency are taken from the devicetree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently our semihosting trap function is somewhat fragile: we rely
on the current compiler behaviour to assign the second inline assembly
argument to the next free register (r1/x1), which happens to be the
"addr" argument to the smh_trap() function (per the calling convention).
I guess this is also the reason for the noinline attribute.
Make it explicit what we want: the "addr" argument needs to go into r1,
so we add another register variable. This allows to drop the "noinline"
attribute, so now the compiler beautifully inlines just the trap
instruction directly into the calling function.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit f4b540e25c5c("arm: smh: Fix uninitialized parameters with newer
GCCs") added a memory clobber to the semihosting inline assembly trap
calls, to avoid too eager GCC optimisation: when passing a pointer, newer
compilers couldn't be bothered to actually fill in the structure that it
pointed to, as this data would seemingly never be used (at least from the
compiler's point of view).
But instead of the memory clobber we need to tell the compiler that we are
passing an *array* instead of some generic pointer, this forces the
compiler to actually populate the data structure.
This involves some rather hideous cast, which is best hidden in a macro.
But regardless of that, we actually need the memory clobber, but for two
different reasons: explain them in comments.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARM semihosting interface uses different trap instructions for
different architectures and instruction sets. So far we were using
AArch64 and ARMv7-M, and had an untested v7-A entry. The latter does
not work when building for Thumb, as can be verified by using
qemu_arm_defconfig, then enabling SEMIHOSTING and SYS_THUMB_BUILD:
==========
{standard input}:35: Error: invalid swi expression
{standard input}:35: Error: value of 1193046 too large for field of 2 bytes at 0
==========
Fix this by providing the recommended instruction[1] for Thumb, and
using the ARM instruction only when not building for Thumb. This also
removes some comment, as QEMU for ARM allows to now test this case.
Also use the opportunity to clean up the inline assembly, and just define
the actual trap instruction inside #ifdef's, to improve readability.
[1] https://developer.arm.com/documentation/dui0471/g/Semihosting/The-semihosting-interface?lang=en
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add test cases for accessing the FWU Metadata on the sandbox
platform. The sandbox platform also uses the metadata access driver
for GPT partitioned block devices.
The FWU feature will be tested on the sandbox64 variant with a raw
capsule. Remove the FIT capsule testing from sandbox64 defconfig --
the FIT capsule test will be run on the sandbox_flattree variant.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The FWU Multi Bank Update feature allows the platform to boot the
firmware images from one of the partitions(banks). The first stage
bootloader(fsbl) passes the value of the boot index, i.e. the bank
from which the firmware images were booted from to U-Boot. On the
STM32MP157C-DK2 board, this value is passed through one of the SoC's
backup register. Add a function to read the boot index value from the
backup register.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
The FWU metadata structure is accessed through the driver model
interface. On the stm32mp157c dk2 and ev1 boards, the FWU metadata is
stored on the uSD card. Add the fwu-mdata node on the u-boot specifc
dtsi file for accessing the metadata structure.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Use binman to build an image which includes all the U-Boot phases so that
a full VBE boot can take place with just that image.bin file. Attach the
image file to mmc2 so it can be loaded.
VBE is used to load images in two phases:
- In VPL, VBE decides which SPL image to load
- In SPL, VBE decides which U-Boot image to load
The latter should really be determined by VPL, since it does the full
signature verification on the selected configuration. However, we have
separate configurations for SPL and U-Boot proper, so for now we keep it
simple and have SPL do its own verification. This will need to be
tidied up later.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we put the driver in the /chosen node in U-Boot. This is a bit
strange, since U-Boot doesn't normally use that node itself. It is better
to put it under the bootstd node.
To make this work we need to copy create the node under /chosen when
fixing up the device tree. Copy over all the properties so that fwupd
knows what to do.
Update the sandbox device tree accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox runs the next phase from discrete executables, so for
example u-boot-tpl runs u-boot-vpl to get to the next phase.
In some cases the phases are all built into a single firmware image, as is
done for real boards. Add support for this to sandbox.
Make it higher priority so that it takes precedence over the existing
method.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the sandbox executable is assumed to be arg[0] but this only
works for a single jump (e.g. from SPL to U-Boot). Add a new arg to solve
this issue, along with a detailed comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox only supports jumping to a file, to get to the next
U-Boot phase. We want to support other methods, so update the code to
use an enum for the method. Also use the
Use board_boot_order() to set the order, so we can add more options.
Also add the MMC methods into the BOOT_DEVICE enum so that booting
from MMC can be supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
This happens every time sandbox moves to the next phase so is not very
interesting. Display the message only when debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present we normally write tests either in Python or in C. But most
Python tests end up doing a lot of checks which would be better done in C.
Checks done in C are orders of magnitude faster and it is possible to get
full access to U-Boot's internal workings, rather than just relying on
the command line.
The model is to have a Python test set up some things and then use C code
(in a unit test) to check that they were done correctly. But we don't want
those checks to happen as part of normal test running, since each C unit
tests is dependent on the associate Python tests, so cannot run without
it.
To acheive this, add a new UT_TESTF_MANUAL flag to use with the C 'check'
tests, so that they can be skipped by default when the 'ut' command is
used. Require that tests have a name ending with '_norun', so that pytest
knows to skip them.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
As STI timer is renamed to ARM A9 global timer, change BCM63138 to use
the new global timer config symbol name.
This patch applies on top of the my previous patch [1].
[1]: https://lists.denx.de/pipermail/u-boot/2022-August/491060.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6753 is essentially same as the main chip BCM6855 but with different
SKU number. Now that BCM6855 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6855, remove the original ARCH_BCM6753 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm96753ref board folder. It is replaced by the
generic bcmbca board folder.
- Merge the 6753.dtsi setting to the new 6855.dtsi file. Update
96753ref board dts with the new compatible string.
- Delete broadcom_bcm96763ref.h and merge its setting to the new
bcm96855.h file.
- Delete bcm96753ref_ram_defconfig and use a basic config version of
bcm96855_defconfig
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6855 is a Broadcom ARM A7 based PON Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
broadband SoC, this patch adds it under CONFIG_BCM6855 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL101 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM6858 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6858, remove the original ARCH_BCM6858 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm968580xref board folder. It is replaced by the generic
bcmbca board folder.
- Update bcm968580xref board dts with the new compatible string.
- Delete broadcom_bcm968580xref.h and merge its setting to the new
bcm96858.h file.
- Remove bcm968580xref_ram_defconfig as a basic config version of
bcm96858_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6858 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other broadband
SoC, this patch adds it under CONFIG_BCM6858 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and the
original dts is updated with the one from linux next git repository.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM68360 is a variant within the BCM6856 chip family. Now that BCM6856
is supported under CONFIG_ARCH_BCMBCA and CONFIG_BCM6856, remove the
original ARCH_BCM68360 support and migrate its configuration and dts
settings. This includes:
- Remove the bcm968360bg board folder. It is replaced by the generic
bcmbca board folder.
- Merge the 68360.dtsi setting to the new 6856.dtsi file. Update board
dts with the new compatible string.
- Merge broadcom_bcm968360bg.h setting to the new bcm96856.h file.
- Remove bcm968360bg_ram_defconfig as a basic config version of
bcm96856_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6856 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other Broadband
SoC, this patch adds it under CONFIG_BCM6856 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and Broadcom uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM63158 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM63158, remove the original ARCH_BCM63158 support and migrate
configuration settings.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63158 is a Broadcom B53 based DSL Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
Broadband SoC, this patch adds it under CONFIG_BCM63158 chip
config and CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL011 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM4908 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added
under ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux git repository so the dts and dtsi
files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM6813 is a Broadcom B53 based PON and WLAN AP router SoC. It is part
of the BCA (Broadband Carrier Access origin) chipset family so it's
added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4912 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts
and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63146 is a Broadcom B53 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63138 is an ARM A9 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory, ARM A9 global timer
and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
This patch applies on top of the my previous patch [1].
[1] https://lists.denx.de/pipermail/u-boot/2022-August/490570.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63148 is an Broadcom B15 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6756 is an ARM A7 based WLAN Gateway and Access Point Broadband SoC.
It is part of the BCA(Broadband Carrier Access origin) chipset family so
it's added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6878 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011
uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6846 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM63178 is an ARM A7 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCY17nfA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPPoAJ0UYyt3kwslUlAJhOC+KU9UlYnVuwCbBXIQyBua
K5clq+GyxXfaDl2Hnvc=
=XXVp
-----END PGP SIGNATURE-----
Merge tag 'video-20221030' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix [hv]sync active vs back porch in dw_mipi_dsi
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
This is actually a panel, not a video device. Rename the option, move it
into the right place and make it depend on PANEL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently sandbox configuration defautls to 64bit and there is no
automation for building 32bit sandbox on 32bit hosts.
Use _LP64 macro as heuristic for detecting 64bit targets.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The jmp_buf type is required by the C99 specification.
Defining it for x86 fixes building the longjmp unit test.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If longjmp(jmp_buf env, int val) is called with val = 0, the setjmp()
macro must return 1.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- nuvoton: add expire function for generic reset (Jim)
- handle watchdogs during keyed autoboot (Rasmus)
- cyclic: Don't disable cylic function upon exceeding CPU time (Stefan)
- ulp wdog: Updates to support iMX93 and DM (Alice)
Layerscape update
- support sysreset,
- de-select FSL_IFC when booting from SD
- disable unused parts of ICID tables
- reduce ns_dev size for csu
- enable dma snooping for ls104x
- nand driver fixups for ls1043ardb rev 7.0 boards.
Avoid the following build errors after the device tree sync:
drivers/spi/mxs_spi.c: In function ‘mxs_spi_probe’:
drivers/spi/mxs_spi.c:327:25: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘spi_max_frequency’
327 | priv->max_freq = dtplat->spi_max_frequency;
| ^~
drivers/spi/mxs_spi.c:328:23: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘num_cs’
328 | plat->num_cs = dtplat->num_cs;
| ^~
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Multiple boards create duplicate entries in their respective
-u-boot.dtsi files which all basically do the same thing.
To consolidate these and make it easier to make improvements
going forward, consolidate them all into one place.
This file creates a flash.bin image using binman, and supports
LPDDR4, DDR4 and DDR3. Since individual boards use different
peripherals and different UART ports, those entries were kept
in their respective board files, but the spba1 node was addded
which contains all UART1-3 to help facilitate SPL_DM_SERIAL.
Individual users will still need to include their respective
UART and pinctrl nodes for those UARTS.
This consolidated file also supports generating a flash.bin file
which can boot from flexSPI if CONFIG_FSPI_CONF_HEADER is
enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The GW7904 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD connector with UHS support
- LIS2DE12 3-axis accelerometer
- Gateworks System Controller
- IMX8M FEC
- 2x RS232 off-board connectors
- PMIC
- 10x bi-color LED's
- 1x miniPCIe socket with PCIe and USB2.0
- 802.3at Class 4 PoE
- 10-30VDC input via barrel-jack
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Plus PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Sync the i.Core MX8M Plus is an EDIMM SoM based on NXP
devicetree file from linux-next tree.
commit <aec8ad34f7f24> (arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus EDIMM2.2 Starter Kit)
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus
from Engicam.
General features:
- NXP i.MX8M Plus
- Up to 4GB LDDR4
- 8 eMMC
- Gigabit Ethernet
- USB 3.0, 2.0 Host/OTG
- PCIe 3.0 interface
- I2S
- LVDS
- rest of i.MX8M Plus features
i.Core MX8M Plus needs to mount on top of Engicam baseboards
for creating complete platform solutions.
Add support for it.
Sync the i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus
from Engicam devicetree file from linux-next tree.
commit <eefe06b295087> (arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus SoM)
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
In order to test that we properly handle watchdog(s) during the "wait
for the user to interrupt autoboot" phase, we need a watchdog device
to be watching us.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
In order to test that U-Boot actually maintains the watchdog device(s)
during long-running busy-loops, such as those where we wait for the
user to stop autoboot, we need a watchdog device that actually does
something during those loops; we cannot test that behaviour via the DM
test framework.
So introduce a relatively simple watchdog device which is simply based
on calling the host OS' alarm() function; that has the nice property
that a new call to alarm() simply sets a new deadline, and alarm(0)
cancels any existing alarm. These properties are precisely what we
need to implement start/reset/stop. We install our own handler so that
we get a known message printed if and when the watchdog fires, and by
just invoking that handler directly, we get expire_now for free.
The actual calls to the various OS functions (alarm, signal, raise)
need to be done in os.c, and since the driver code cannot get access
to the values of SIGALRM or SIG_DFL (that would require including a
host header, and that's only os.c which can do that), we cannot simply
do trivial wrappers for signal() and raise(), but instead create
specialized functions just for use by this driver.
Apart from enabling this driver for sandbox{,64}_defconfig, also
enable the wdt command which was useful for hand-testing this new
driver (especially with running u-boot under strace).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmNSPhMcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDrHCACddHL6pElPVUvNWomJ
h7RNejIaFrm+V2tVoDqnUBEzxKod7g1cvBiZM+2o5fcLNIrWfH0gV+7a48Uybzt2
r7VZ9u5Rnl1Fhhjvr8eL3uF/39V249eMPrzR8xC677sCJJkcczoOw8n4y534FaJZ
1NePmMKhlo7YVEZKzwdg1sM6sUppXniSEXUllWumVaUgSHcZhFK579nCbYpt25bW
sJ1V3fY2pJnaFHv9H599zSK79Izf5fR4fr3egKZknw8oqNLKNrjkWxxlPXJfjEYr
ncFJ31dOZXJU09rRoE60nIc0QdRE8dvELjYhPKUS/wmFDg7IotwNj5GcX2RIlRPJ
mS22
=D3FL
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 fixes for the 2023.01 cycle:
This small fixes set includes an indentation fix for sam9x60 DT and one
name for one pin for sama7g5.
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Add Serial Download Protocol support as it is a useful method to
load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot
proper using the following 'uuu'command:
$ uuu -brun spl flash.bin
Based on a patch from Marek Vasut for the imx8mm-mx8menlo board.
Also, to fit the SPL binary into the internal RAM, select CONFIG_LTO
to reduce its size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Enable DM USB, DM PHY and USB gadget support in imx8mm-mx8menlo SPL
to let the board continue SDP loading of second stage after the first
stage was loaded by BootROM SDP implementation. It is not possible to
jump back into BootROM v1 and let the BootROM implementation continue
the SDP loading, all this has to be performed by the U-Boot CI HDRC
controller driver and SDP protocol implementation, both of which fit
into the SPL just barely.
With this patch, it is possible to start both U-Boot SPL and U-Boot
using e.g. uuu on this board as follows:
$ uuu -brun spl flash.bin
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The signal name of pin PB2 with function F is FLEXCOM11_IO1
as it is defined in the datasheet.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
The indentation went far on the right due to an extra tab for
each pinctrl sub-nodes.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
- dts update and sync for rk356x, rk3288, rk3399 from Linux;
- Add rk3399 EAIDK-610 board support;
- Update for puma-rk3399 board;
- some fix and typo fix in different drivers;
The first production revision of the MX8M Mini Menlo board implements
a hardware change which swaps console UART and another UART connector.
Implement the swap, which maps the console UART back to the way Verdin
console is mapped.
Signed-off-by: Marek Vasut <marex@denx.de>
The GW7903 revision B adds two additional GPIO's to control the
direction of the 2 isolated digital I/O circuits.
Define them as:
- dig1_ctl
- dig2_ctl
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Update the M2 socket gpio hogs such that they are not active on boot by
flagging them as GPIO_ACTIVE_HIGH so that 'output-high' drives high.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Update the UART config gpio hogs such that it is configured for RS232
by default on boot. Additionally rename them to match the names used
on the reset of the venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable the I2C bus and set a env variable for the reset GPIO of the touch
controller. This allows us to probe the panel in a script.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This adds support for the Kontron Electronics SoM SL i.MX8MM OSM-S
and the matching baseboard BL i.MX8MM OSM-S.
The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
The existing board configuration for the non-OSM SoM is reused and
allows to detect the SoM variant at runtime.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Improve the naming of the regulators to contain the voltage rail
names from the schematic.
Suggested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.
Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This adjusts the names of the boards and SoMs to the official naming
used by Kontron marketing. These changes also affect devicetree
names and compatibles. The same changes have been submitted to the
Linux kernel.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The new stable configuration is missing the 100mt setpoint, remove
it before updating the config to make sure the changes are separated
cleanly.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable the redundant environment feature to allow falling back in case of
storage corruption. The partition layout for the SPI NOR device is added
to the devicetree.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The display isn't and won't be used in U-Boot. Also the display setup
is not yet supported in mainline Linux, so even for cases where the
U-Boot devicetree is passed to the kernel there is currently no use
for this configuration.
Selecting the proper configuration in the kernel FIT image automatically
depending on the detected hardware can be handled by a script in the
environment.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Beside some rather unexciting sync of the DTs from the kernel tree, and
some Kconfig cleanup, there are some improvements for the ARMv5 Allwinner
family, to support boards with the F1C200s (64MB DRAM) better. We will
get actual board support as soon as the DTs have passed the Linux review
process.
There is also support for the X96 Mate TV Box, featuring the H616 SoC and
a full 4GB of DRAM.
Also we found the secret to enable SPI booting on the H616 (pin PC5 must
be pulled to GND), so the SPI boot support patch is now good to go.
Passed the gitlab CI, plus briefly tested on Pine64-LTS, LicheePi Nano,
X96 Mate and OrangePi Zero.
The IPI scheme in OpenSBI has been updated to support 8-core AE350
platform, the plicsw configuration needs to be modified accordingly.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The riscv32 toolchain for GCC-12 provided by kernel.org contains libgcc.a
compiled for double-float. To link to it we have to adjust how we build
U-Boot.
As U-Boot actually does not use floating point at all this should not
make a significant difference for the produced binaries.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Some boards with the Allwinner F1C100s family SoCs use UART1 for its
debug UART, so define the pins for the SPL and the pinmux name and mux
value for U-Boot proper.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
So far we stated the lack of a lowlevel() init function for the
Allwinner F1C100s board by defining the respective SKIP_* symbol in the
board's defconfig. However we don't expect any *board* to employ such
low level code, so expect this to be never used for the ARMv5 Allwinner
SoCs.
Select the appropriate symbols in the Kconfig, so that we can remove
them from the defconfig, and avoid putting them in future defconfigs for
other boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Traditionally we assumed that every Allwinner board would come with at
least 256 MB of DRAM, and set our DRAM layout accordingly. This affected
both the default load addresses, but also U-Boot's own address
expectations (like being loaded at 160 MB).
Some SoCs come with co-packaged DRAM, but only provide 32 or 64MB. So
far we special-cased those *chips*, as there was only one chip per DRAM
size. However new chips force us to take a more general approach.
Introduce a Kconfig symbol, which provides the minimum DRAM size of the
board. If nothing else is specified, we use 256 MB, and default to
smaller values for those co-packaged SoCs.
Then select the different DRAM maps according to this new symbol, so
that different SoCs with the same DRAM size can share those definitions.
Inspired by an idea from Icenowy.
This is just refactoring: compiled for all boards before and after this
patch: the binaries were identical.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The enable_caches function in architecture-specific board code is only
necessary for V7A CPUs, code for both V8A and ARM926 have already
declared this function.
Only provide our implementation of enable_caches() for V7A CPUs.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that a single binary containing TPL/SPL correctly formatted for SPI
flashes and U-Boot proper, can be generated by binman, let's do it.
Also update the documentation to tell the user to use this newly
generated file instead of manually generating and flashing the binaries.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The offset of the SPL payload on Puma is different than for other
Rockchip devices in that it is stored at offset 256K instead of much
further away in the MMC.
Flashing one binary instead of two at different offsets is much more
user friendly so let's migrate to it by modifying the offset in the Puma
specific Device Tree.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Depending on the toolchain used to compile the SPL for Puma RK3399-Q7
module, the board does not boot because the resulting binary is too big
to fit in SRAM.
Let's add a TPL so that there's no need to fiddle with or hack the
defconfig to have a working bootloader.
This follows what's been done for the majority of other RK3399-based
boards.
See the original commit for the first migrations:
bdc0008011 "rockchip: rk3399: update defconfig for TPL"
Unfortunately, the offset in SPI-NOR for U-Boot proper needs to be
modified, since the move from SPL to TPL+SPL for idbloader.img (and the
"only the first 2KB per 4KB blocks are written" "hack" for rkspi format)
increased the size above 256KB. Let's move it to 512KB to, hopefully, be
safe.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Trying to load U-Boot proper from SPL when SPL was not loaded from
SD-Card is currently not working because the SDMMC pins aren't muxed
correctly. It is assumed the BootROM is doing this for us when booting
from SD-Card hence why it's not needed when booting TPL/SPL from
SD-Card.
The pinctrl properties are removed from the SPL DT property removal list
and the pinctrl configuration nodes made available in the SPL DT, in
addition to the pull-up configurations to allow loading U-Boot proper
from SD-Card as a fallback mechanism for SPI-NOR and eMMC.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On Haikou devkit, it is possible to disable eMMC and SPI-NOR to force
booting from SD card or USB via rkdeveloptool by toggling a switch. This
switch needs to be overridden in software to be able to access eMMC and
SPI-NOR once the device has booted from SD Card. Puma SoM can override
this pin via gpio3_d5.
Until now, fixed regulator device was abused to model this, but since
there's now support for GPIO hogs, let's use it.
Since we want to be able to boot the SPL from SD Card but give it the
ability to load U-Boot proper from a fallback medium such as eMMC and
SPI-NOR, SPL support for GPIO hogs needs to be enabled too. Support for
other kinds of regulators are not needed anymore, so let's disable them.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Specification
- Rockchip RK3399
- LPDDR3 4GB
- TF sd scard slot
- eMMC
- AP6255 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1 work in otg mode
- 12V DC Power supply
The dts file is sync from linux-next[0].
[0]:https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
UART0 can obviously also be used for debug uart in U-Boot, so let's add
its support.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The check to perform is on CONFIG_SPL_GPIO and not SPL_GPIO.
Because this was never compiled in, it missed an include of cru.h that
was not detected before. Let's include it too.
Also switch to IS_ENABLED in-code check as it is the preferred
inclusion/exclusion mechanism.
Fixes: 07586ee432 ("rockchip: rk3399: Support common spl_board_init")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The check to perform is on CONFIG_SPL_DM_REGULATOR and not
SPL_DM_REGULATOR. Also switch to in-code check instead of ifdefs.
Fixes: 07586ee432 ("rockchip: rk3399: Support common spl_board_init")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com> # Rock960
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Partial sync of rk3288.dtsi from Linux version 5.18
Changed:
only properties and functions that are not yet included
swap some clocks positions
fix some irq numbers
style and sort nodes
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version update the cpu and gpu nodes.
Changed:
use operating-points-v2
update thermal for all cpus
add labels to all cpus
change gpu compatible
change gpu interrupt names
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version move thermal sub nodes to the dtsi
file and remove rk3288-thermal.dtsi
Changed:
replace underscore in nodename
remove comments about sensor and ID
use gpu phandle
add #cooling-cells to gpu node
lower critical temparature
remove linux,hwmon property
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The phycore_rk3288 board has a SPL size problem,
so remove phycore_init() function to stay within the limits.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These hardware register definitions are common for all K3, remove
duplicate data them by moving them to hardware.h.
While here do some minor whitespace cleanup + grouping.
Signed-off-by: Andrew Davis <afd@ti.com>
This matches how this would be done in Linux and these functions
do the alignment for us which makes the code look cleaner.
Signed-off-by: Andrew Davis <afd@ti.com>
This matches what we did for pre-K3 devices. This allows us to build
boot commands that can check for our device type at runtime.
Signed-off-by: Andrew Davis <afd@ti.com>
Move to latest DDR4 1600MT/s for k3-am64-evm based on EMIF tool
v0.08.40.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Move k3-am64-sk to use 1600MT/s LPDDR4 configuration and update to latest EMIF
tool v0.08.40.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Support VBE OS requests / fixups
Minor error-handling tweaks to bootm command
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmNOjr4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreakFQf/bLTFMI8noOMa9d6Yo1RTSOa9wNiomgzC
JGY7g8i7b6cARwQ+QuSncnO/EOpwjzBLWkohUK3UAktJu2LURBPJFR4qeP01F7iz
4Mn3ikYlr3vRxAPeckN7l1aqSWrY/tEXbUdXLxSn+COzjxCQG5aBU1jd/tVBqIAk
XgZ0NGVHOQe8XOPNxDP9+EYHw4kmqMSdWZmpkb1w+Jh5AIYMMDgn1ktiNmnWXllx
LM89JxR8FMUJzFP9XBRtYemje55tAUPlENthRip9Zj9touEBbBKjV5eY8YsjpMMU
Vt5rK33vKWE4mdNBjRmOoe9xkUv/pRclpaGUFBNswf2LGw7/lsHd2A==
=3P/S
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18oct22' of https://source.denx.de/u-boot/custodians/u-boot-dm
Update uclass iterators to work better when devices fail to probe
Support VBE OS requests / fixups
Minor error-handling tweaks to bootm command
The H616 SoC uses the same SPI IP as the H6, also shares the same clocks
and reset bits.
The only real difference is a slight change in the pin assignment: the
H6 uses PC5, the H616 PC4 instead. This makes for a small change in
our spi0_pinmux_setup() routine.
Apart from that, just extend the H6 #ifdef guards to also cover the H616,
using the shared CONFIG_SUN50I_GEN_H6 symbol.
Also use this symbol for the Kconfig dependency.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Ivan Shishkin <s45rus@gmail.com>
Update the devicetree files from the Linux kernel, version v6.0-rc4.
This is covering the 32-bit SoCs, from arch/arm/boot/dts/.
This avoids the not backwards-compatible r_intc binding change, to allow
older kernels to boot, but the other nodes are updated.
Not much change here, the vast majority is actually cosmetic: node names
and using symbolic names for the the RTC clocks.
The R40 boards gain DVFS support.
Some A23/A33 tablet DTs are unified into a single file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Update the devicetree files from the Linux kernel, version v6.0-rc4.
This is covering the 64-bit SoCs, from arch/arm64/boot/dts/allwinner.
This avoids the not backwards-compatible r_intc binding change, to allow
older kernels to boot, but the other nodes are updated.
Not much change here, the vast majority is actually cosmetic: node names
and using symbolic names for the the RTC clocks.
Some A64 boards gain some audio nodes.
The H616 DTs are now switched to the version finally merged into the
kernel, which brings some changes, but none affecting U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Fix the compilation issue when CONFIG_DEBUG_UART is activated
drivers/serial/serial_stm32.o: in function `debug_uart_init':
drivers/serial/serial_stm32.c:291: undefined reference to \
`board_debug_uart_init'
The board_debug_uart_init is needed for SPL boot, called in
cpu.c::mach_cpu_init(); it is defined in board/st/stm32mp1/spl.c.
But with the removal #ifdefs patch, the function debug_uart_init() is
always compiled even if not present in the final U-Boot image.
This patch adds a file to provided this function when DEBUG_UART and SPL
are activated.
Fixes: c8b2eef52b ("stm32mp15: tidy up #ifdefs in cpu.c")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The PWR regulators don't need be removed as they are already deactivated.
This patches is a alignment with the accepted patch in Linux device tree
in commit a34b42f8690c ("ARM: dts: stm32: fix pwr regulators references
to use scmi").
Fixes: 69ef98b209 ("ARM: dts: stm32mp15: alignment with v5.19")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Fix the frequencies listed in PLL configuration comments to match
the actual frequencies programmed into hardware. Furthermore, add
a comment which explains how those frequencies are calculated, so
it won't be necessary to look it up all over the datasheet and
make more mistakes in the calculation in the future.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add DT for DHCOR Testbench board, which is a testbench for testing of
DHCOR SoM during manufacturing. This is effectively a trimmed down
version of AV96 board with CSI-2 bridge, HDMI bridge, WiFi, Audio and
LEDs removed and used as GPIOs instead. Furthermore, the PMIC Buck3
is always configured from PMIC NVM to cater for both 1V8 and 3V3 SoM
variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case the regulator-always-on is present in regulator DT node,
the regulator is always reconfigured to the voltage set in DT on
probe, even if regulator_set_value() has been called before. Drop
the property from AV96 U-Boot DT and enable the regulator manually
in code, as the board already reconfigures the Buck3 regulator in
code per PMIC NVM content instead.
Fixes: 0adf10a87b ("ARM: dts: stm32: Configure Buck3 voltage per PMIC NVM on Avenger96")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
There are a couple users of uclass_next_device return value that get the
first device by other means and use uclass_next_device assuming the
following device in the uclass is related to the first one.
Use uclass_next_device_err because the return value from
uclass_next_device will be removed in a later patch.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is a number of users that use uclass_first_device to access the
first and (assumed) only device in uclass.
Some check the return value of uclass_first_device and also that a
device was returned which is exactly what uclass_first_device_err does.
Some are not checking that a device was returned and can potentially
crash if no device exists in the uclass. Finally there is one that
returns NULL on error either way.
Convert all of these to use uclass_first_device_err instead, the return
value will be removed from uclass_first_device in a later patch.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several parts of the ICID table are only necessary for U-Boot proper.
Disable them in SPL. This saves around 500 bytes.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
FSL_IFC should only be selected when booting from NAND flash (or when
NAND_FSL_IFC is enabled). The existing logic does this correctly when
QSPI is also enabled, but not when just booting from SD.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
CONFIG_SYSRESET provides its own implementation of reset_cpu. Disable
our version when it is enabled.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This enables eDMA snooping on the LS1043A and LS1046A. This will allow
marking the I2C, LPUART, and SPI devices on these SoCs as DMA coherent.
Oddly, this bit is only documented for the LS1043A, and is marked as
"reserved" in the LS1046ARM. I have tested this patch on the LS1046A
and found that marking i2c0 as dma-coherent works without issue.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Provide a simple sandbox driver for the thermal uclass.
It simply registers and returns 100 degrees C if requested.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is used as delay for gpmi write strobe.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
- Update RISC-V to use 32bit or 64bit toolchains, depending on if we're
building for 32bit or 64bit CPUs. This requires updating the Docker
container as well to have the 32bit toolchain.
The following description is copied from the equivalent patch for the
Linux Kernel proposed by Aurelien Jarno:
>From version 2.38, binutils default to ISA spec version 20191213. This
means that the csr read/write (csrr*/csrw*) instructions and fence.i
instruction has separated from the `I` extension, become two standalone
extensions: Zicsr and Zifencei. As the kernel uses those instruction,
this causes the following build failure:
arch/riscv/cpu/mtrap.S: Assembler messages:
arch/riscv/cpu/mtrap.S:65: Error: unrecognized opcode `csrr a0,scause'
arch/riscv/cpu/mtrap.S:66: Error: unrecognized opcode `csrr a1,sepc'
arch/riscv/cpu/mtrap.S:67: Error: unrecognized opcode `csrr a2,stval'
arch/riscv/cpu/mtrap.S:70: Error: unrecognized opcode `csrw sepc,a0'
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Christian Stewart <christian@paral.in>
Reviewed-by: Rick Chen <rick@andestech.com>
make W=1 generates the following warning in cpu_disable, cpu_status and
cpu_release functions.
arch/arm/mach-zynqmp/mp.c:166:16: warning: comparison of unsigned expression
in '>= 0' is always true [-Wtype-limits]
166 | if (nr >= ZYNQMP_CORE_APU0 && nr <= ZYNQMP_CORE_APU3) {
| ^~
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221004053454.25470-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When MMU is already enabled then dcache_enable() does not call mmu_setup()
and so setup_all_pgtables() is also never called.
In this situation when some driver calls mmu_set_region_dcache_behaviour()
function then U-Boot crashes with error message:
Emergency page table not setup.
Fix this issue by explicitly calling setup_all_pgtables() in dcache_enable()
function near condition for mmu_setup().
This change fixes chainloading U-Boot from U-Boot on Turris Mox board which
uses mvneta ethernet driver which calls mmu_set_region_dcache_behaviour().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In order to move ppc-specific code out of setup_dest_addr(), provide an
arch-specific variant arch_setup_dest_addr(), that can be used by
architecture code to fix up the initial reloc address.
It is called at the end of setup_dest_addr() initcall and the default
implementation is a nop stub.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
asm/mach_type.h header and CONFIG_MACH_TYPE macro are arm-specific, so move
related bdinfo logic to arch_setup_bdinfo() in arch/arm/lib/bdinfo.c.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
The XTRN_DECLARE_GLOBAL_DATA_PTR declarations in ppc code are permanently
commented out, so there are no users for this macro:
#if 1
#define DECLARE_GLOBAL_DATA_PTR register volatile gd_t *gd asm ("r2")
#else /* We could use plain global data, but the resulting code is bigger */
#define XTRN_DECLARE_GLOBAL_DATA_PTR extern
#define DECLARE_GLOBAL_DATA_PTR XTRN_DECLARE_GLOBAL_DATA_PTR \
gd_t *gd
#endif
Remove all references to this macro, but add a documentation note regarding
the possibility of using plain global data for the GD pointer.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
VHV_Enable GPIO is required to enable during eFuse programming on Armada
SoCs not from 3700 family. Add support for enabling and disabling VHV pin
via GPIO during eFuse programming, when specified.
All details are in Marvell AN-389: ARMADA VHV Power document
(Doc. No. MV-S302545-00 Rev. C, August 2, 2016).
Note that due to HW Errata 3.6 eFuse erroneous burning (Ref #: HWE-3718342)
VHV power must be disabled while core voltage is off to prevent erroneous
eFuse programming.
This is specified in Marvell ARMADA 380/385/388 Functional Errata,
Guidelines, and Restrictions document
(Doc. No. MV-S501377-00 Rev. D, December 1, 2016).
Signed-off-by: Pali Rohár <pali@kernel.org>
This patch implements LD eFuse programming support. Armada 385 contains two
LD eFuse lines, each is 256 bit long with one additional lock bit. LD 0
line is mapped to U-Boot fuse bank 64 and LD 1 line to fuse bank 65. U-Boot
32-bit fuse words 0-8 are mapped to LD eFuse line bits 0-255. U-Boot fuse
word 9 is mapped to LD eFuse line lock bit.
So to program LD 1 General Purpose Data line, use U-Boot fuse command:
=> fuse prog -y 65 0 0x76543210
=> fuse prog -y 65 1 0xfedcba98
=> fuse prog -y 65 2 0x76543210
=> fuse prog -y 65 3 0xfedcba98
=> fuse prog -y 65 4 0x76543210
=> fuse prog -y 65 5 0xfedcba98
=> fuse prog -y 65 6 0x76543210
=> fuse prog -y 65 7 0xfedcba98
=> fuse prog -y 65 8 0x1
Signed-off-by: Pali Rohár <pali@kernel.org>
Since the move to CONFIG_TIMER with support for CONFIG_TIMER_EARLY, this
platform specific init_timer() function is not needed any more. Let's
remove it completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Michael Walle <michael@walle.cc>
Cc: Pali Rohár <pali@kernel.org>
These boards are out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Stefan Roese <sr@denx.de>
For future DM based FPGA drivers and for now to have a meaningful
logging class for old FPGA drivers.
Suggested-by: Michal Simek <michal.simek@amd.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Dahl <post@lespocky.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220930120430.42307-2-post@lespocky.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
When the imx8mn.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
When the imx8mn.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Provide a way to copy over the 'other' FDT when running tests. This loads
it and allocates memory for the copy, if not done already, then does the
copy.
Avoid using U-Boot's malloc() pool for these copies, at least for now,
since they are part of the test system.
Tidy up the cpu.c header files while here.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need an 'other' FDT which is different from the control FDT, so we can
check that the ofnode tests correctly handle them both.
Add this to the build along with a way to read it into the sandbox state.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this implementation is specific to loading the test FDT. We
plan to load others, so create a generic function to handle this.
The path is now limited to 256 characters, to simplify the code.
When there is an empty argv[0] (which should not happen), the function now
just uses the path as is, with no prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is helpful to test that out-of-memory checks work correctly in code
that calls malloc().
Add a simple way to force failure after a given number of malloc() calls.
Fix a header guard to avoid a build error on sandbox_vpl.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
- SPL fixes for STM32F7 MCUs
- Device tree alignement with kernelv6.0-rc4 for MCU's board
- Device tree alignement with kernelv6.0-rc3 for MPU's board
- Update DDR node for STM32MP15
- Cleanup config file for STM32MP1
- Update for cmd_stm32key command
- Fix compatible string to add partitions for STM32MP1
- Update for stm32programmer tool
-----BEGIN PGP SIGNATURE-----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=iA80
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220927' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Increase SYS_MALLOC_F_LEN for STM32 MCU's board
- SPL fixes for STM32F7 MCUs
- Device tree alignement with kernelv6.0-rc4 for MCU's board
- Device tree alignement with kernelv6.0-rc3 for MPU's board
- Update DDR node for STM32MP15
- Cleanup config file for STM32MP1
- Update for cmd_stm32key command
- Fix compatible string to add partitions for STM32MP1
- Update for stm32programmer tool
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYzGwogAKCRDKSWXLKUoM
Ial4AJ9+4WHn0MV2X7gK1fyh4lUW7ggPhQCggsYlSoACgMgdji17SAPhCv/W3IA=
=BmA9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc1-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1 (round 2)
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
Device tree alignment with kernel v6.0-rc4.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Versal NET platform is based on Versal chip which is reusing a lot of IPs.
For more information about new IPs please take a look at DT which describe
currently supported devices.
The patch is adding architecture and board support with soc detection
algorithm. Generic setting should be very similar to Versal but it will
likely diverge in longer run.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/320206853dc370ce290a4e7b6d0bb26b05206021.1663589964.git.michal.simek@amd.com
In SMP all harts will register themself in available_hart
during start up. Then main hart will send IPI to other harts
according to this variables. But this mechanism may not
guarantee that all other harts can jump to next stage.
When main hart is sending IPI to other hart according to
available_harts, but other harts maybe still not finish the
registration. Then the SMP booting will miss some harts finally.
So let it become an option and it will be enabled by default.
Please refer to the discussion:
https://www.mail-archive.com/u-boot@lists.denx.de/msg449997.html
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
U-Boot and SPL don't necessary share the same location, so we might end
with U-Boot SPL in read-only memory (XIP) and U-Boot in read-write memory.
In case of non XIP boot mode, we rely on such variables as "hart_lottery"
and "available_harts_lock" which we use as atomics.
The problem is that CONFIG_XIP also propagate to main U-Boot, not only SPL,
so we need CONFIG_SPL_XIP to distinguish SPL XIP from other XIP modes.
This adds an option special for SPL to behave it in XIP manner and we don't
use hart_lottery and available_harts_lock, during start proccess.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add a simple uclass test for SCSI. It reads the partition table from a
disk image and checks that it looks correct.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox is producing a warning about SCSI migration. Drop the
legacy code and replace it with a new implementation.
Also drop the SATA command, which does not work with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
The following faulty behavior was observed. The sandbox configured with
CONFIG_SANDBOX_CRASH_RESET=y was invoked with
./u-boot -T -S
After executing `exception undefined' the sandbox reboots.
When executing `exception undefined' the sandbox exits with SIGSEGV.
The expected behavior is that the sandbox should reboot again.
If we are relaunching the sandbox in a signal handler, we have to unblock
the respective signal before calling execv(). See signal(7) man-page.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
During init_dram() is called also setup_ddr_tlbs_phys() function which may
print message about unmapped DDR memory. So in this case print also
re-aligning filler after unmapped DDR memory message.
Signed-off-by: Pali Rohár <pali@kernel.org>
Currently U-Boot SPL prints just generic message "2 GiB left unmapped".
Change it to more detailed "2 GiB of DDR memory left unmapped in U-Boot".
This is just U-Boot configuration and operating system may map more (or
also less) memory.
Signed-off-by: Pali Rohár <pali@kernel.org>
Commit 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
changed type of ram_top member from ulong to phys_addr_t but did not
changed types in board_get_usable_ram_top() function which returns value
for ram_top.
So change ulong to phys_addr_t type also in board_get_usable_ram_top()
signature and implementations.
Fixes: 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The input clock for uart is too slow (25MHz) which introduces frequent data
error on both receiving and transmitting even if the baudrate is 115200.
Using high-speed can significantly solve this issue.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds general board files based on MT7981 SoCs.
MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:
1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add general board files based on MT7986 SoCs.
MT7986 uses one mmc controller for booting from both SD and eMMC.
Both MT7986A and MT7986B use the same pins for spi controller.
Configs for various boot types:
1. mt7986_rfb_defconfig - SPI-NOR and SPI-NAND for MT7986A/B
2. mt7986a_bpir3_emmc_defconfig - eMMC for MT7986A only
3. mt7986a_bpir3_sd_defconfig - SD for MT7986A only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds basic support for MediaTek MT7981 SoC.
This include the file that will initialize the SoC after boot and its
device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds basic support for MediaTek MT7986 SoC.
This include the file that will initialize the SoC after boot and its
device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Remove the unnecessary nodes for TFABOOT and keep the mandatory part
in SOC dtsi, only the DDRCTRL and DDRPHY addresses.
This patch allows to manage the DDR configuration setting in U-Boot
device tree only if it is needed, when CONFIG_SPL is defined.
With TFABOOT, the DDR configuration is done in TF-A BL2 and the DDR size
is dynamically computed in U-Boot since commit d72e7bbe7c ("ram:
stm32mp1: compute DDR size from DDRCTL registers").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change the mask of OTP0 used to close the device on STM32MP
- STM32MP15x: bit 6 of OPT0
- STM32MP13x: 0b111111 = 0x3F for OTP_SECURED closed device
And support the 2 keys for STM32MP13x
- PKHTH : Hash of the 8 ECC Public Keys Hashes Table
(ECDSA is the authentication algorithm)
- EDMK : Encryption/Decryption Master Key
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Update the command stm32key to support several keys selected by
key name and managed by the new sub-command:
stm32key list
stm32key select [<key>]
stm32key read -a
This patch doesn't change the STM32MP15 behavior, only PKH is
supported, but it is a preliminary patch for STM32MP13 support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Split the read_hash_otp function and introduce the helper function
read_close_status to read the close status in OTP separately of the PKH.
This patch is a preliminary step for STM32MP13 support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add defines for value used in stm32key for BSEC permanent lock status
and error.
This patch is a preliminary step to support more lock status in BSEC
driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Improve the partitioning trace done in command stm32prog:
- remove the trace "partition: Done" when the GPT partitioning is not done
- indicate the mmc instance used for each 'gpt write' command
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
As the SMC is only supported in SP-MIN for STM32MP15x, the associated
partition should be absent when the TA NVMEM is not available in OPT-TEE
in STM32MP13x.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Solve many compilation warning when stm32prog is activated on the aarch64.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change the defaut flashlayout location, hardcoded at STM32_DDR_BASE,
to CONFIG_SYS_LOAD_ADDR to avoid issue on board with reserved memory
at STM32_DDR_BASE.
This patch changes the command behavior for STM32MP13 and STM32MP15
platform, as CONFIG_SYS_LOAD_ADDR(0xc2000000) != STM32_DDR_BASE
but without impact for serial boot with STM32CubeProgrammer.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When the STM32CubeProgrammer sent a empty flashlayout.tsv
file, the command stm32prog correctly parse the file
but data->dev_nb = 0 and the stm32prog_devices_init
operations should be skipped.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
TI DP83867 is using strapping based on MIO pins. Tristate setup can influce
PHY address. That's why switch description with ethernet-phy-id compatible
string which enable calling reset. PHY itself setups phy address after
power up or reset. Reset description will be added in separate commit.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/52bf9ac0453d4e4896d8edd2618e684bb1ff6012.1662721547.git.michal.simek@amd.com
The upstream Linux DSA drivers do not require phy-handle nodes in
the DSA ports yet the U-Boot DSA drivers do. Add a phy-handle and
the mdio nodes to the u-boot.dtsi file so that future dts file
syncrhonization between Linux and U-Boot don't break networking.
Fixes: 24a7a3c1c0 ("imx8mm: synchronise device tree with linux")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The upstream Linux DSA drivers do not require phy-handle nodes in
the DSA ports yet the U-Boot DSA drivers do. Add a phy-handle and
the mdio nodes to the u-boot.dtsi file so that future dts file
syncrhonization between Linux and U-Boot don't break networking.
Fixes: e0caa84ca6 ("imx8mp: synchronise device tree with linux")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmMoEdgcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyNvEB/4nEeiBx7Lo1gK+79PJ
9kCUngglHRu3/+FJMpcOp+2b6sSW1IZs8qGBMAMFSRoFElrLMMbVEgBR0ZfJCl3c
It0xN9Buhe8muwtAdE8Amr4PddUEynzglVPpFUFfir6ZqFAcedmN6iuh+K82r7Be
7s/8tRb2hVp//TpkEntf2yxrYnyeW4qiXyUxbUhaUyyhkM3RBXySuY4qnaaLp3NY
R9rsIY5j3kA2QylebEamlXI+KDvszrGbkUOUUrlwkygQNR/GmAYQPlY1TdBwk0wE
U1CO8zQYaL3OY998lU32pMVClmwyXbn2i7KAyMm3TEgrfpjQsLTS2BK+w+RBdMGL
XGnt
=lRvM
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.01 cycle:
This feature set includes the important update on PIO4 pinctrl driver
that solves a long time mismatch between Linux and U-boot, related on
the unification of pinctrl and gpio driver support, now respecting the
pinctrl bindings ABI; and also support for pinctrl subnodes. The feature
set also adds support for PDA screen detection for sam9x60_curiosity
board , one fix for SD-Card reinsertion and one fix for sam9x60 clocks.
Adding the "u-boot,dm-pre-reloc" DT property to the timer node is
necesssary to support the timer in the early boot phases (e.g.
SPL & pre-reloc).
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Add the DT bindings / descriptions for timer0 & timer1, exactly as done
in mainline Linux.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
This patch changes the compilation, so that the Armada 375 board(s) are
compiled in a separate step. This is necessary for the timer dts
conversion, as A375 has a different / timer description in the dts.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Now that the new timer support is available for these platforms, let's
select this IF for all these platforms. This way it's not necessary
that each board changes it's config header.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
With the recent changes in the Marvel mvneta network driver, the MDIO
bus is not connected any more. This patch updates the DT nodes to use
the nodes from the dtsi files instead of creating ad-hoc nodes.
Signed-off-by: Stefan Roese <sr@denx.de>
I messed up application of patch 5a428e7510 ("mmc: fsl_esdhc_spl: Add
support for builds without CONFIG_SYS_MMC_U_BOOT_OFFS"). I took it from
a work-in-progress branch where I changed usage of
CONFIG_SDCARD to CONFIG_SD_BOOT
and refactored
SYS_MPC85XX_NO_RESETVEC
mess.
But these changes aren't in master yet. Fix the wrong usage of these
macros.
Fixes: 5a428e7510 ("mmc: fsl_esdhc_spl: Add support for builds without
CONFIG_SYS_MMC_U_BOOT_OFFS")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
This patch makes sure that the Devicetree for the sama7
boards are aligned with the Devicetree from Linux. This
implies removing the GPIO compatible and replacing it
with the PINCTRL one, as well as unifying the SDMMC
pinctrl related subnodes under one single subnode.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
This patch makes sure that the Devicetree for the sama5
boards are aligned with the Devicetree from Linux. This
implies removing the GPIO compatible and replacing it
with the PINCTRL one, as well as unifying the SDMMC
pinctrl related subnodes under one single subnode.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Fix copy-paste error of the I2C5 bus recovery GPIO assignment,
the I2C5 GPIOs are on gpio3 instead of gpio5.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
The ECSPI1 is on I2C1/I2C2 pins of the SoC, update the pinmux accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Rename imx8mp-dhcom-pdk2-u-boot.dtsi to imx8mp-dhcom-u-boot.dtsi, since
this file is shared by PDK2, PicoITX and DRC02. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
This PHY is not used on PDK2, the header was added due to copy-paste
error, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Add information about which exact SoM variant is used on which PDK2 variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Adam Ford <aford173@gmail.com>
Fix spurious ampersand in address print e.g.
Find img info 0x&480331a0, size 855
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>"
The NXP i.MXRT1170 Evaluation Kit (EVK) provides a platform for rapid
evaluation of the i.MXRT, which features NXP's implementation of the Arm
Cortex-M7 and Cortex-M4 core.
The EVK provides 64 MB SDRAM, Micro SD card socket,
USB 2.0 OTG.
This patch aims to support the preliminary booting up features
as follows:
GPIO
LPUART
SD/MMC
SDRAM
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
This commit adds board support for i.MXRT1170-EVK from NXP. This board
is an evaluation kit provided by NXP for i.MXRT117x processor family.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Only one occurance of WATCHDOG_RESET is left in one assembler file.
This patch changes this occurance to a direct call to watchdog_reset
and then removes all the ASSEMBLY ifdef'ery in watchdog.h, as it's not
needed any more to clean this mess a bit up.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
When fixed offset via CONFIG_SYS_MMC_U_BOOT_OFFS is not specified then
expects that U-Boot proper is placed immediately after SPL without any
additional padding.
This allows to generate smaller SPL+U-Boot final binary as it is not
required to specify fixed offset to U-Boot proper at SPL compile time.
In this case offset to U-Boot proper is calculated at SPL compile time in
linker script.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Change 8-byte alignment of SPL binary to just 4-byte alignment as objcopy
trims trailing zero bytes when converting ELF file to RAW binary.
This is same fix for SPL linker script as was done fix for U-Boot linker
script in commit e8c0e0064c ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE
support").
It is required for the patch "mmc: fsl_esdhc_spl: Add support for builds
without CONFIG_SYS_MMC_U_BOOT_OFFS" which triggered this issue in SPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Commit d433c74eec ("Convert CONFIG_SDCARD et al to Kconfig") converted
SYS_EXTRA_OPTIONS=SDCARD or SPIFLASH to config options CONFIG_SDCARD and
CONFIG_SPIFLASH, but left one occurance unchanged.
Fix this.
Fixes: d433c74eec ("Convert CONFIG_SDCARD et al to Kconfig")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Building of final u-boot.bin binary for mpc85xx via binman is needed only
when inserting DTB binary in the middle of the u-boot ELF binary (before
.bootpg and .resetvec ELF sections).
These requirements are met when CONFIG_MPC85XX_HAVE_RESET_VECTOR is enabled
(= generating .bootpg/.resetvec sections) and CONFIG_OF_SEPARATE is enabled
(= inserting DTB binary).
So in all other cases use standard build procedure instead of custom
mpc85xx u-boot.bin Makefile target via binman.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Currently Makefile produces final mpc85xx image when SPL is not used in
custom file u-boot-with-dtb.bin. It is quite confusing name as build
process produce also intermediate file standard file u-boot-dtb.bin (which
is just intermediate and not bootable). Other platforms use u-boot.bin
(UBOOT_BIN) as standard name for final bootable raw image.
So change Makefile rules and binman to produce final bootable file for
mpc85xx also into file u-boot.bin. There is just need for mpc85xx to not
define default rule for u-boot.bin then instruct binman (via DTS file) to
store final image into u-boot.bin (instead of u-boot-with-dtb.bin) and
finally rename target u-boot-with-dtb.bin to u-boot.bin.
With this change are also removed custom Makefile hacks for mpc85xx that it
produced non-standard output file. And also updated documentation.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable this option on all boards which support block devices. Drop the
related depencies on BLK since these are not needed anymore.
Disable BLOCK_CACHE on M5253DEMO as this causes a build error.
Signed-off-by: Simon Glass <sjg@chromium.org>
* Remove unnecessary device tree nodes which are not needed in
U-Boot directly.
* Move all U-Boot specific device tree properties to u-boot dtsi.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Commit 6337d53fdf ("arm: dts: sync am33xx with Linux 5.9-rc7") syncs
the am335x device tree with the latest linux kernel am335x device tree.
That causes problems with device tree in SPL stage.
To fix the issues CONFIG_SPL_OF_TRANSLATE must be set to handle the
synced bus addresses correctly.
A custom U-Boot device tree is also needed since the SPL build removes
bus properties from bus nodes which are not explicitly marked with the
u-boot,dm-spl or u-boot,dm-pre-reloc flag. Therefore all parent buses of
the in the SPL needed devices must be marked with u-boot,dm-pre-reloc.
Also since there is no driver for "ti,sysc" compatible property in SPL
the buses marked with this compatible string must also be marked with
compatible = "simple-bus" to make the underlying devices visible in
SPL. Otherwise the matching device drivers aren't found and the uclass
drivers are dropped.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The SPI and NAND board variants never went into production.
Drop those board variants.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
