Some register value was hardcoded for System memory size 128MB and
memory offset 0x08000000. This patch fixed the problem.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
It is necessary for some pci device driver.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Commit af1c2b84 added a generic phy support, with an ID of zero
and a 32 bit mask; meaning that it will match on any PHY ID.
The problem is that there is a test that checked if a matching
PHY was found, and if not, it printed the non-matching ID.
But since there will always be a match (on the generic PHY,
worst case), this test will never trip.
In the case of a misconfigured PHY address, or of a PHY that
isn't explicitly supported outside of the generic support,
you will never see the ID of 0xffffffff, or the ID of the
real (but unsupported) chip. It will silently fall through
onto the generic support.
This change makes that test useful again, and ensures that
the selection of generic PHY support doesn't happen without
some sort of notice. It also makes it explicitly clear that
the generic PHY must be last in the PHY table.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
This patch adds I2C mux support for the fsl_i2c driver. This
allows you to add "new" i2c busses, which are reached over
i2c muxes. For more infos, please look in the README and
search for CONFIG_I2C_MUX.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The smc911x driver has a lot of useful defines/functions which can be used
by pieces of code (such as example eeprom programmers). Rather than
forcing each place to duplicate these defines/functions, split them out
of the smdc911x driver into a local header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Guennadi Liakhovetski <lg@denx.de>
CC: Magnus Lilja <lilja.magnus@gmail.com>
CC: Ben Warren <biggerbadderben@gmail.com>
Add a driver for the Synchronous Display Controller and the Display
Interface on i.MX31, using IPU for DMA channel setup. So far only
displaying of bitmaps is supported, no text output.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This is a driver for the S6E63D6 SPI OLED display controller from Samsung.
It only provides access to controller's registers so the client can freely
configure it.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Some SPI devices have special requirements on chip-select handling.
With this patch we can use a GPIO as a chip-select and strictly follow
the SPI_XFER_BEGIN and SPI_XFER_END flags.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This is a minimal driver, so far only managing output. It will
be used by the mxc_spi.c driver.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Fix setting the SPI Control register, 8 and 16-bit transfers
and a wrong pointer in the free routine in the mxc_spi driver.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This is just a handy routine that reports last PCI busno: we walk
down all the hoses and return last hose's last_busno.
Will be used by PCI/PCIe initialization code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Added the struct containing PHY settings for the Vitesse VSC8211 phy to
the phy_info list in tsec.c
Signed-off-by: Pieter Henning <phenning@vastech.co.za>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Serial driver via the EmbeddedICE macrocell's DCC channel using
co-processor 14.
It does include a timeout to ensure that the system does not
totally freeze when there is nothing connected to read.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This driver implements the ECC algorithm described in
the CPU data sheet and uses the OOB layout chosen in
already-released development systems (shipped with a custom-made
u-boot 1.3.1).
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Fix the problem that cannot use external hub, because this driver
did not control correctly a DEVADDx register.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch does some minor fixing of the Xilinx Spartan III
FPGA boot code:
- Fixed call order of post configuration callback and
success message printing (result of copy-paste?)
- remove obsolete comment
- minor coding style cleanup
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch does some minor fixing of the Xilinx Spartan II
FPGA boot code:
- Fixed call order of post configuration callback and
success message printing (result of copy-paste?)
- relocate post configuration callback only when it
is implemented
- remove obsolete comment
- minor coding style cleanup
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
These names are being taken over by the new MMC framework. Hopefuly
the PXA can be easily ported, and these functions will go away entirely.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
omap3_mmc.c was changed to define mmc_legacy_init.
Remove unused functions.
Compile tested on all arm
Runtime tested on Zoom1.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
judging from other printfs in the same file, it seems ata should be
postpended with the interface number, not the address of the global
port variable. Fixes this for current u-boot-mpc83xx tree:
Configuring for MPC8349ITX board...
sata_sil3114.c: In function 'sata_bus_softreset':
sata_sil3114.c:99: warning: format '%u' expects type 'unsigned int', but argument 2 has type 'struct sata_port *'
sata_sil3114.c:108: warning: format '%u' expects type 'unsigned int', but argument 2 has type 'struct sata_port *'
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch will create a configuration option for a minimum configuration for
the ns16550 serial driver at drivers/serial/ns16550.c and will apply this new
configuration option to the SIMPC8313.h config file in order to fix the NAND
bootstrap build error. This option will exclude all functions with exception of
NS16550_putc and NS16550_init. This will be used primarily to save space and
remove unused code from builds in which space is limited.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Move the CONFIG_8xx mpc8xx_pcmcia.c protection out of the C file and
into the Makefile so we avoid pointless compiling of the file.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Here's a new framework (based roughly off the linux one) for managing
MMC controllers. It handles all of the standard SD/MMC transactions,
leaving the host drivers to implement only what is necessary to
deal with their specific hardware.
This also hooks the infrastructure into the PowerPC board code
(similar to how the ethernet infrastructure now hooks in)
Some of this code was contributed by Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Added various p2020 processor specific details:
* SVR for p2020, p2020E
* immap updates for LAWs and DDR on p2020
* LAW defines related to p2020
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
V3: Fixed line-wrap problem due to user error in mail!
Added usb_configured() checks in usbtty_puts() and usbtty_putc() to get around a hang
when usb is not connected and the user has set up multi-io (setenv stdout serial,usbtty etc).
Got rid of redundant __attribute__((packed)) directives that were causing warnings from gcc.
Signed-off-by: Atin Malaviya <atin.malaviya@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
i.MX31 powers on with most clocks running, so, after a power on this explicit
clock start up is not required. However, as Linux boots it disables most clocks
to save power. This includes the I2C clock. If we then soft reboot from Linux
the I2C clock stays off. This breaks the phycore, which has its environment in
I2C EEPROM. Fix the problem by explicitly starting the clock in I2C driver
initialisation routine.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Ack-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
At some point an intentional double space at the end of the sentence
got changed into a tab in the GPL header line:
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
This patch fixes the damage.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
If on your board is more than one flash, you must know
the size of every single flash, for example, for updating
the DTS before booting Linux. So make this function
flash_get_info() extern, and you can have all info
about your flashes.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Added new CONFIG options for the three type of MAC-PHY interconnect and
applied them all relevant board config files
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
SOFT_RESET must be asserted for at least 3 TX clocks. Usually, that's about 30
clock cycles, so it's been mostly working. But we had no guarantee, and at
slower bitrates, it's just over a microsecond (over 1000 clock cycles). This
enforces a 2 microsecond gap between assertion and deassertion.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
100Mbs ethernet does not work on sh7763 chips due to the wrong value being
used in the GECMR register. Following diff fixes the problem
Signed-off-by: Simon Munton <simon@nidoran.m5data.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The code assumes that the pci bus address and the virtual
address used to access a region are the same, but they might
not be. Fix this assumption.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
It is no longer always true that the pci bus address can be
used as the virtual address for pci accesses. pci_map_bar()
is created to return the virtual address for a pci region.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Driver for Dave DNET ethernet controller (used on Dave/DENX
QongEVB-LITE board).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
When we search for an address match in pci_hose_{phys_to_bus,bus_to_phys}
we should give preference to memory regions that aren't system memory.
Its possible that we have over mapped system memory in the regions and
we want to avoid depending on the order of the regions.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI_REGION_MEMORY and PCI_REGION_MEM are a bit to similar and
can be confusing when reading the code.
Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY to clarify its used
for system memory mapping purposes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Without the timeout present an infinite loop can occur if the
NAND device is broken or not present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Commit cfa460adfd removed support
for disabling the "No NAND device found!!!" warning when
CONFIG_SYS_NAND_QUIET_TEST was defined. This re-adds support
for silencing the warning.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Dear Wolfgang,
You are right, the patch was ugly.
The new one seems to be better.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Modified mii_init to support boards with PHYs that are not set to
autonegotiate, but still want to use u-boot's mii commands to probe
the smi bus. Such PHYs will not set the Autonegotiate-done bit.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Applied the patch for baudrate divider value truncation for
serial_init to serial_setbrg as well.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small typo and compilation warning for systems with CFI
legacy support (e.g. hcu4). This patch fixes it.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the double defined manufacturer defines from
jedec_flash.c. Since the common defines in flash.h are 32bit
we now need the (16) cast. This patch also removes the compilation
warning (e.g. seen on hcu5):
./MAKEALL hcu5
Configuring for hcu5 board...
jedec_flash.c:219: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Stefan Roese <sr@denx.de>
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small compilation warning. This patch fixes it.
Signed-off-by: Stefan Roese <sr@denx.de>
include/flash.h was commented to say that the address in
flash_info->start was a physical address. However, from u-boot's
point of view, and looking at most flash code, it makes more
sense for this to be a virtual address. So I corrected the
comment to indicate that this was a virtual address.
The only flash driver that was actually treating the address
as physical was the mtd/cfi_flash driver. However, this code
was using it inconsistently as it actually directly dereferenced
the "start" element, while it used map_physmem to get a
virtual address in other places. I changed this driver so
that the code which initializes the info->start field calls
map_physmem to get a virtual address, eliminating the need for
further map_physmem calls. The code is now consistent.
The *only* place a physical address should be used is when defining the
flash banks list that is used to initialize the flash_info struct,
usually found in the board config file.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Somehow I missed the real driver part in my last patch version. This patch
now adds the driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This is a port of the Linux Blackfin on-chip SDH driver to U-Boot.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is a port of the Linux Blackfin on-chip ATAPI driver to U-Boot.
Signed-off-by: Sonic Zhang <Sonic.Zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Redo how pointers are managed to get rid of ugly casts and strict pointer
aliasing issues that are highlighted by gcc 4.3.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
No point in having a Blackfin-specific define "CONFIG_BFIN_MAC_RMII" that
does exactly the same thing as common "CONFIG_RMII".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Rather then defining our own DEBUGF(), just use the common debug().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Rather than having the on-chip MAC hardcoded to phy address 1 and a speed
of 2.5mhz, use these as defaults if the board doesn't specify otherwise.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Cleanup and rewrite the MII/PHY related functions so that we can reuse the
existing common linux/miiphy.h code and hook into the `mii` command.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Rather than hardcoding MDCDIV to 24 (which is correct for ~125mhz SCLK),
use the real algorithm so it gets set correctly regardless of SCLK.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds support for searching through available PHY-addresses in
the macb-driver. This is needed for the ATEVK1100 evaluation board,
where the PHY-address will be initialized to either 1 or 7.
This patch adds a config option, CONFIG_MACB_SEARCH_PHY, which when
enabled tells the driver to search for the PHY address.
Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adjusts the LED control so that interrupt lines are not reading LEDs
and effectively causing indefinite interrupts to the controller.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds routines to handle (flush/invalidate) the dcache for the
QH and qTD structures and data buffers. This is needed on platforms using
this EHCI support with dcache enabled (like the MIPS VCT board port).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch adds the config option CONFIG_EHCI_HCD_INIT_AFTER_RESET
to call ehci_hcd_init() again after ehci_reset() is executed. This
is needed for the upcoming VCT EHCI support which needs to re-init
the hcd part again after the EHCI CMD_RESET is executed.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch fixes an issue that the speed of USB devices was not detected
correctly on some EHCI controllers. This will be used on the upcoming VCT
EHCI support.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Adding DM6446 (TI DaVinci) platform specific USB functionality for
USB Phy and VBUS initialization.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Adding Mentor USB core functionality and Mentor USB Host controller
functionality for Mentor USB OTG controller (musbhdrc).
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Add USB ehci ixp4xx host controller. Test on ixdp465 board.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
USB ehci code cleanup. Use handshake instead of infinite while loop
to check the STD_ASS status
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Add USB ehci pci support. This patch doesn't include any
pci_ids and it is not tested on real hardware.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
- fix ehci_readl, ehci_writel
- introduce new define in ehci.h
- introduce the handshake function for waiting on a register
- fix usb_ehci_fsl with the new HC_LENGTH macro
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Böhmer <linux@bohmer.net>
IXP465 board and I find some errors in the code. This
patch fix:
- descriptor initizialization (config, interface and endpoint
must be one next-to the other when the USB_DT_CONFIG message
is send.
- FIX little/endian bigendian (introduce the CONFIG_EHCI_DESC_BIG_ENDIAN
and the CONFIG_EHCI_MMIO_BIG_ENDIAN)
- Introduce the linux version of the usb_config_descriptor and
usb_interface descriptor. This descriptor does't contains
u-boot extension.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Böhmer <linux@bohmer.net>
The current Blackfin i2c driver does not work properly with certain devices
due to it breaking up transfers incorrectly. This is a rewrite of the
driver and relocates it to the newer place in the source tree.
Also remove duplicated I2C speed defines in Blackfin board configs and
disable I2C slave address usage since it isn't implemented.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch adds a #define to optionally change the behaviour of
i2c_read() in soft_i2c.c to send an I2C repeated start instead of a
stop-start between sending the device address pointer write and
reading back the data. The current behaviour is retained as the
default.
While most devices will work either way, I have a smart battery(*)
that requires repeated start, and someone at some point found a
device that required a stop-start.
(*) http://www.inspired-energy.com/Standard_Products/NL2054/NL2054%20Rev1.0%20Data%20Sheet.pdf
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
Added flash_fixup_stm to fix geometry reversal on STMicro M29W320ET flash chip.
Modeled after flash_fixup_amd, this patch handles the geometry reversal
or erase sectors that exist for ST Micro (now Numonyx) M29W320ET flash.
Since I cannot test all STM's chips, the detection is implemented as
narrow as possible for now.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The function find_sector() doesn't need to be called twice in
the case of AMD command set.
Tested on TQM5200S-BD with Samsung K8P2815UQB.
Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Stefan Roese <sr@denx.de>
sh_eth used old network API. This patch changed new API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch changes the reg_read/_write to smc911x_reg_read/_write
and defines then as weak so that they can be overridden by board
specific version.
This will be used by the upcoming VCTH board support.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Higher spi flash layers expect to be given back a pointer that was
malloced so that it can free the result, but the lower layers return
a pointer that is in the middle of the malloced memory. Reorder the
members of the lower spi structures so that things work out.
Signed-off-by: Brad Bozarth <bflinux@yumbrad.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Initial support for the DS4510, a CPU supervisor with
integrated EEPROM, SRAM, and 4 programmable non-volatile
GPIO pins. The CONFIG_DS4510 define enables support
for the device while the CONFIG_CMD_DS4510 define
enables the ds4510 command. The additional
CONFIG_DS4510_INFO, CONFIG_DS4510_MEM, and
CONFIG_DS4510_RST defines add additional sub-commands
to the ds4510 command when defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Moved driver vcth.c to vct.c to better reflect the VCT board series.
This driver is now used by the VCT platforms:
vct_premium
vct_platinum
vct_platinumsvc
Signed-off-by: Stefan Roese <sr@denx.de>
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define
#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
but that's bogus and did not work anyhow.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Enable nand lock, unlock and status of lock feature.
Not every device and platform requires this, hence,
it is under define for CONFIG_CMD_NAND_LOCK_UNLOCK
Nand unlock and status operate on block boundary instead
of page boundary. Details in:
http://www.micron.com/products/partdetail?part=MT29C2G24MAKLAJG-6%20IT
Intial solution provided by Vikram Pandita <vikram.pandita@ti.com>
Includes preliminary suggestions from Scott Wood
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Rather than putting the function prototype for board_nand_init() in the one
place where it gets called, put it into nand.h so that every place that also
defines it gets the prototype. Otherwise, errors can go silently unnoticed
such as using the wrong return value (void rather than int) when defining
the function.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Add subpage write support
- Add onenand_oob_64/32 ecclayout
This has been missing and without it UBI has some incompatibilies issues
with the current (>= 2.6.27) Linux kernel version. vid_hdr_offset is
placed differently (2048 instead of 512) without this fix.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The version (ver_id) was not stored in the onenand_chip structure and
because of this the continuous locking scheme could be enabled on some
chips.
Signed-off-by: Stefan Roese <sr@denx.de>
The current code that determines which bank/chipselect is used for a
given NAND instance only worked for 32-bit addresses and assumed
a 1:1 mapping. This breaks in 36-bit physical configs.
The proper way to handle this is to use the virt_to_phys() and
BR_PHYS_ADDR() routinues to match the 34-bit lbc bus address
with the the virtual address the NAND code uses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Initial support for NXP's 4 and 8 bit I2C gpio expanders
(eg pca9537, pca9557, etc). The CONFIG_PCA953X define
enables support for the devices while the CONFIG_CMD_PCA953X
define enables the pca953x command. The CONFIG_CMD_PCA953X_INFO
define enables an 'info' sub-command which provides summary
information for the given pca953x device.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Add fsl_pci_config_unlock() function to enable a
PCI/PCIe interface configured in agent/endpoint mode to
respond to inbound PCI configuration cycles.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Otherwise, recursion can occur if scan_bbt does not find a bad block
table, and tries to write one, and the attempt to erase the BBT area
causes a bad block check.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The stmicro_wait_ready() func tries to show the actual opcode that was sent
to the device, but instead it displays the array pointer. Fix it to pull
out the opcode from the start of the array.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
All implementations of the functions i2c_reg_read() and
i2c_reg_write() are identical. We can save space and simplify the
code by converting these functions into inlines and putting them in
i2c.h.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-By: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The address of SCFSR register is wrong at SH7720/SH7721.
This patch fix this.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
fsl_pci_init.c: In function 'fsl_pci_setup_inbound_windows':
fsl_pci_init.c:122: warning: comparison is always true due to limited range of data type
The check only makes sense if we are CONFIG_PHYS_64BIT
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this patch now, the user can call "ubi part" multiple times to
re-connect the UBI device to another MTD partition.
Signed-off-by: Stefan Roese <sr@denx.de>
Don't use LIST_HEAD() but initialize the struct via INIT_LIST_HEAD() upon
first call of add_mtd_partitions(). Otherwise this won't work on platforms
where the relocation is broken (like MIPS or PPC).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch tries to ensure that phy interrupt pin
won't be asserted after booting. We experienced
following issues with current 88E1121R phy init:
Marvell 88E1121R phy can be hardware-configured
to share MDC/MDIO and interrupt pins for both ports
P0 and P1 (e.g. as configured on socrates board).
Port 0 interrupt pin will be shared by both ports
in such configuration. After booting Linux and
configuring eth0 interface, port 0 phy interrupts
are enabled. After rebooting without proper eth0
interface shutdown port 0 phy interrupts remain
enabled so any change on port 0 (link status, etc.)
cause assertion of the interrupt. Now booting Linux
and configuring eth1 interface will cause permanent
phy interrupt storm as the registered phy 1 interrupt
handler doesn't acknowledge phy 0 interrupts. This
of course should be fixed in Linux driver too.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The current code will cause the creation of a 4GB window
starting at 0 if we have more than 4GB of RAM installed,
which overlaps with PCI_MEM space and causes pci_bus_to_phys()
to return erroneous information. Limit the size to 4GB - 1;
which causes the code to create one 2GB and one 1GB window
instead.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
This patch fix the problem that only the [NB_DATAFLASH_AREA - 1] dataflash
partition can be defined to use the area to the end of dataflash size.
Now it is possible to have only one dataflash partition from 0 to the end
of of dataflash size.
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
This caused the operation to be needlessly repeated if there were
no bad blocks and no errors.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Remove a printf() from add_mtd_device(), which produces spurious output.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add cfi-mtd driver, which exports CFI flash to MTD layer.
This allows CFI flash devices to be used from MTD layer.
Building of the new driver is controlled by CONFIG_FLASH_CFI_MTD
option. Initialization is done by calling cfi_mtd_init() from
flash_init().
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add interface for flash verbosity control. It allows
to disable output from low-level flash API. It is useful
when calling these low-level functions from context other
than flash commands (for example the MTD/CFI interface
implmentation).
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Export flash_sector_size() function from drivers/mtd/cfi_flash.c,
so that it can be used in the upcoming cfi-mtd driver.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch defines all flash access functions as weak so that
they can be overridden by board specific versions.
This will be used by the upcoming VCTH board support where the NOR
FLASH unfortunately can't be accessed memory-mapped. Special
accessor functions are needed here.
To enable this weak functions you need to define
CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS in your board config header.
Otherwise the "old" default functions will be used resulting
in smaller code.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This MTD part infrastructure will be used by the upcoming
UBI support.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Copied over the fixed PHY driver as used in pp4xx/4xx_enet.c.
This adds support for PHY-less MAC connections to the UEC.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
All CF platforms' mii.c are consolidated into one
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Also changed path in all linker scripts that reference this driver
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Patch to fix buffer allocation size and alignment. Buffer needs to be u32 aligned and
PKTSIZE_ALIGN bytes long.
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The current uec_miiphy_read and uec_miiphy_write hardcode access devlist[0]
This patch makes these function use the devname argument that is passed in to
allow access to the phy registers of other devices in devlist[].
Signed-of-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Fixed compiler warning "declared but unused" eth5_uec_info and eth6_uec_info.
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch fixes a problem on systems where the NOR flash is attached
to a 64 bit bus. The toggle bit detection in flash_toggle() is based
on the assumption that the same flash address is read twice without
any other interjacent flash accesses. However, on 32 bit systems the
function flash_read64() [as currently implemented] does not perform
an atomic 64 bit read - instead, this is broken down into two 32 bit
read accesses on addresses "addr" and "addr + 4". So instead of
reading a 64 bit value twice from "addr", we see a sequence of 4 32
bit reads from "addr", "addr + 4", "addr", and "addr + 4". The
consequence is that flash_toggle() fails to work.
This patch implements a simple, but somewhat ugly solution, as it
avoids the use of flash_read64() in this critical place (by breaking
it down manually into 32 bit read operations) instead of rewriting
flash_read64() such to perform atomic 64 bit reads as one could
expect. However, such a rewrite would require the use of floating
point load operations, which becomes pretty complex:
save MSR;
set Floating Point Enable bit in MSR;
use "lfd" instruction to perform atomic 64 bit read;
use "stfd" to store value to temporary variable on stack;
load u64 value from temporary variable;
restore saved MSR;
return u64 value;
The benefit-cost ratio of such an implementation was considered too
bad to actually attempt this, especially as we can expect that such
an implementation would not only have a bigger memory footprint but
also cause a performance degradation.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
As reported by Ilko Iliev <iliev@ronetix.at>, the "nand erase clean"
command is currently broken, and among other things causes all blocks
to be marked bad.
This implements it properly using MTD_OOB_AUTO, along with some
indentation fixes.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Hardware expects ECCM 0 for small page and ECCM 1 for large page
when booting from NAND, so use those defaults.
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it
can be shared by both 83xx and 85xx
- Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards
files which use lbus83xx_t.
- Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that
85xx can share them.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Some chips require a RESET after power-up (e.g. Micron MT29FxGxxxxx).
The first command sent is NAND_CMD_READID.
Issue a NAND_CMD_RESET in nand_scan_ident before reading the device id.
Tested with an MT29F4G08AAC.
Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This brings the core NAND code up to date with the Linux kernel.
Since there were several drivers in Linux as of the last update that are
not in u-boot, I'm not bringing over new drivers that have been added
since in the absence of an interested party.
I did not update OneNAND since it was recently synced by Kyungmin Park,
and I'm not sure exactly what the common ancestor is.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The existing code has a few errors that need to be fixed in
order to support large RAM sizes. Fix those, and add a
comment to make it clearer.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
If the board _didn't_ request INVLINE_INVERTED, we set INVLINE_INVERTED,
otherwise we don't. WTF?
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
atmel_lcdfb doesn't actually need anything from asm/arch/hardware.h. It
includes a file that does, asm/arch/gpio.h, but this file doesn't
include <asm/arch/hardware.h> like it's supposed to.
Add the missing include to asm/arch/gpio.h and remove the workaround
from the atmel_lcdfb driver. This makes the driver compile on avr32.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add a common setup function that determines the pci_region(s) based
on how much memory we have in the system.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
* PCI Inbound window was setup incorrectly. The PCI address and system
address were swapped. The PCI address should be setting piwar/piwbear
and the system address should be setting pitar.
* Removed masking of addresses to allow for system address to support
system address & PCI address >32-bits
* Set PIWBEAR & POTEAR to allow for full 64-bit PCI addresses
* Respect the PCI_REGION_PREFETCH for inbound windows
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
PCI bus is inherently 64-bit. While not all system require access to
the full 64-bit PCI address range some do. This allows those systems
to enable the full PCI address width via CONFIG_SYS_PCI_64BIT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Debug sessions may have left enabled laws.
Changing lawbar with an unkown enabled tgtid could cause problems.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch fixes the following warnings, when using
the soft_i2c driver using no CPU pins on MPC82xx or MPC8xx
systems:
soft_i2c.c: In function 'send_reset':
soft_i2c.c:93: warning: unused variable 'immr'
soft_i2c.c: In function 'send_start':
soft_i2c.c:124: warning: unused variable 'immr'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:146: warning: unused variable 'immr'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:171: warning: unused variable 'immr'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:196: warning: unused variable 'immr'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:244: warning: unused variable 'immr'
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds support for the National LM63 temperature
sensor with integrated fan control. It's used on the GDSys
Neo board (405EP) which will be submitted later.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Acked-by: Stefan Roese <sr@denx.de>
Added as a convenience for other platforms that uses MPC8360 (has 8 UCC).
Six eth interface is chosen because the platform I am using combines
UCC1&2 and UCC3&4 as 1000 Eth and the other four UCCs as 10/100 Eth.
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Change UEC phy interface from GMII to RGMII on MPC8568MDS board
Because on MPC8568MDS, GMII interface is only recommended for 1000Mbps speed,
but RGMII interface can work at 10/100/1000Mbps, and RGMII interface works more stable.
Now both UEC1 and UEC2 can work properly under u-boot.
It is also in consistent with the kernel setting for 8568 UEC phy interface.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The function parse_line() in common/main.c was exposed globally by commit
6636b62a6e, Result in conflict with the same
name funciton in drivers/bios_emulator/x86emu/debug.c when define the DEBUG.
This patch fix this by renaming the function in the debug.c file.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
At a lot of places in the code the PIPE_INTERRUPT flags and friends
are used wrong. The wrong bits are compared to this flag resulting
in wrong conditions. Also there are macros that should be used for
PIPE_* flags.
This patch tries to fix them all, however, I was not able to test the
changes, because I do not have any of these boards.
Review required!
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
The max packet size is encoded as 0,1,2,3 for 8,16,32,64 bytes.
At some places directly 8,16,32,64 was used instead of the encoded
value. Made a enum for the options to make this more clear and to help
preventing similar errors in the future.
After fixing this bug it became clear that another bug existed where
the 'pipe' is and-ed with PIPE_* flags, where it should have been
'usb_pipetype(pipe)', or even better usb_pipeint(pipe).
Also removed the triple 'get_device_descriptor' sequence, it has no use,
and Windows nor Linux behaves that way.
There is also a poll going on with a timeout when usb_control_msg() fails.
However, the poll is useless, because the flag will never be set on a error,
because there is no code that runs in a parallel that can set this flag.
Changed this to something more logical.
Tested on AT91SAM9261ek and compared the flow on the USB bus to what
Linux is doing. There is no difference anymore in the early initialisation
sequence.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
The checks for CFG_EEPROM_PAGE_WRITE_ENABLE and
CFG_EEPROM_PAGE_WRITE_BITS in various temperature
sensor drivers are not necessary
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
When the total size of all NAND devices exceeds 4 GiB, the size will
overflow. This patch tries to fix this.
Note that we still have a problem when a single NAND device is bigger
than 4 GiB: then the overflow would actually happen earlier, i. e.
when storing the size in nand_info[].size, as nand_info[].size is an
"u_int32_t".
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Currently VSC8601 doesn't link with 10/100M partners if the
EEPROM/Strapping is not set up.
Setting the auto-neg register fixes this.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
get_prom function was used __attriute__ , but it is not enable.
ax88796.o does not do link besides ne2000.o. When ld is carried
out, get_prom function of ax88796.c is ignored.
This problem is a thing by specifications of ld.
I checked and test this patch on SuperH and MIPS.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The flash_unlock_seq requires a sector for AMD_LEGACY.
Fix a retcode check typeo.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The CFI flash driver starts at flash_init() which calls down into
flash_get_size(). This starts by calling flash_detect_cfi(). If said
function fails, flash_get_size() finishes by attempting to reset the
flash. Unfortunately, it does this with an info->portwidth set to 0x10
which filters down into flash_make_cmd() and that happily smashes the
stack by sticking info->portwidth bytes into a cfiword_t variable that
lives on the stack. On a 64bit system you probably won't notice, but
killing the last 8 bytes on a 32bit system usually leads to a corrupt
return address. Which is what happens on a Blackfin system.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch refactors some large routines of the USB OHCI code by
making some routines smaller and more readable which helps
debugging and understanding the code. (Makes the code looks
somewhat more like the Linux implementation.)
Also made entire file compliant to Linux Coding Rules (checkpatch.pl compliant)
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Fix TBI PHY accesses to use the proper offset in CPU register space. The
previous code would incorrectly access the TBI PHY by reading/writing to CPU
register space at the same location as would be used to access external PHYs.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.
Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.
But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.
This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:
OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.
To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The i.MX31 has three SPI buses and each bus has several chip selects
and the MC13783 chip can be connected to any of these. The current
RTC driver for MC13783 is hardcoded for CSPI2/SS2.
This patch makes make MC13783 SPI bus and chip select configurable
via CONFIG_MC13783_SPI_BUS and CONFIG_MC13783_SPI_CS.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Fix printf format-string/arg mismatches under -DDEBUG.
These warnings occur with DEBUG defined for a platform using
cpu/mpc85xx. Users of other architectures can unearth similar
problems by adding the line "CFLAGS += -DDEBUG=1" in config.mk right
after "CFLAGS += $(call cc-option,-fno-stack-protector)".
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
A recent commit (936897d4d1)
enabled the usb_stop() command in common/cmd_bootm.c which was
not enabled for some time, because no board did actually set the
CFG_CMD_USB flag. So, now the usb_stop() is executed before
loading the linux kernel.
However, the usb_ohci driver hangs up (at least on AT91SAM) if the
driver is stopped twice (e.g. the peripheral clock is stopped on AT91).
If some other piece of code calls usb_stop() before the bootm command,
this command will hangup the system during boot.
(usb start and stop is typically used while booting from usb memory stick)
But, stopping the usb stack twice is useless anyway, and a flag already
existed that kept track on the usb_init()/usb_stop() calls.
So, we now check if the usb stack is really started before we stop it.
This problem is now fixed in both the upper as low-level layer.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Acked-by: Markus Klotzbuecher <mk@denx.de>
Several source files need to be compiled and linked when one or more
config options are selected. To allow for easy selection in the
Makefiles yet to avoild multiple compilation (which costs build time)
and especially multiple linking (which causes errors), we use
"COBJS = $(sort COBJS-y)" which eliminates duplicates.
By courtesy of Detlev Zundel who suggested this approach.
Signed-off-by: Wolfgang Denk <wd@denx.de>
They only differ in the init function.
This also adds the missing watchdog support for the PL011.
Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
This patch adds Lime GDC support together with support for the PWM
backlight control through the w83782d chip. The reset pin of the
latter is attached to GPIO, so we need to reset it in
early_board_init_r.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Some of multi-function USB controllers (e.g. ISP1562) allow root hub
resetting only via EHCI registers. So, this patch adds the
corresponding kind of reset to OHCI's hc_reset() if the newly
introduced CONFIG_PCI_EHCI_DEVNO option is set (e.g. for Socrates
board).
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Acked-by: Markus Klotzbuecher <mk@denx.de>
The RSK7203 board has the SMSC9118 wired up 'incorrectly'.
Byte-swapping is necessary, and so poor performance is inevitable.
This problem cannot evade by the swap function of CHIP, this can
evade by software Byte-swapping.
And this has problem by FIFO access only. pkt_data_pull/pkt_data_push
functions necessary to solve this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Modified board_eth_init() functions of boards that have this FEC in addition
to other Ethernet controllers.
Affected boards:
bc3450
icecube
mvbc_p
o2dnt
pm520
total5200
tq5200
Removed initialization of controller from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Affected boards:
hidden_dragon
MPC8544DS
MPC8610HPCN
R2DPLUS
TB0229
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Adds support for configuring the TBI to talk properly with the SerDes.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The tsec driver contains a hard-coded array of configuration information
for the tsec ethernet controllers. We create a default function that works
for most tsecs, and allow that to be overridden by board code. It creates
an array of tsec_info structures, which are then parsed by the corresponding
driver instance to determine configuration. Also, add regs, miiregs, and
devname fields to the tsec_info structure, so that we don't need the kludgy
"index" parameter.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This is to prepare the way for board code passing in the tsec_info structure
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Renesas SH7723 has 5 SCIF, SD, Camera, LCDC and other.
This patch supports CPU register's header file and SCIF serial driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As noted by Harald Welte, HWFLOW support in the S3C64XX serial driver is
broken and currently unused. Remove it.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Notice: USB on S3C6400 currently works _only_ with switched off MMU. One could
try to enable the MMU, but map addresses 1-to-1, and disable data cache, then
it should work too and we could still profit from instruction cache.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
The existing I2C freqency dividers for FDR does not apply
to ColdFire platforms; thus, a seperate table is added
based on MCF5xxx Reference Manual
Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: Tabi Timur <timur@freescale.com>
The MPC8536 Adds SDHC and SATA controllers to the PQ3 family. We
also have SERDES init code for the 8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
dm9000 has code to detect and initialize external phy parts, but later
on in the code the part is forced to use the internal phy
unconditionally. Remove the unused/untested code.
change the GPIO initialization so that only the GPIO used as an
internal phy reset (hardwired in the chip) is set as an output. The
remaining GPIO need to be handled by board specific code to prevent
possible drive conflicts. Set as inputs for safety.
replace a few magic numbers with defines
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Add FEC Buffer descriptors and data buffer in SRAM for
faster execution and access.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The only board using this driver is the SL8245 board.
Removed initialization for the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Added board_eth_init() function to bf537-stamp board.
Removed initialization for the Blackin EMAC driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Provide a helper function that will setup the last available
LAWs (upto 2) for DDR. Useful for SPD/dyanmic DDR setting code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This "||" doesn't seem to work. Now using the idea suggest by Scott Wood
to combine both config options into one line. This even allows defining
both options and not generating the target object twice.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a missing vendor code in the flash_real_protect() function.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
New implement sector lock and unlock or softlock commands
do not exist in AMD legacy flash. Thus, causing issue
when erasing AMD legacy flash (such as lv040)
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a problem that RTL8110SCL started transfer
with an incorrect memory address.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The received status and len was in little endian
format and caused the ethernet unable to proceed
further. Add __le16_to_cpu() in dm9000_rx_status_8/16/32bit().
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Since page size field is changed from oobblock to writesize. But OneNAND is not updated.
- fix bufferram management at erase operation
This patch includes the NAND/OneNAND state filed too.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
onenand_print_device_info():
- Now returns a string to be placed in mtd->name,
rather than calling printf.
- Remove verbose parameter as it becomes useless.
Signed-off-by: Fathi Boudra <fabo@debian.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fixes an issue with chip->state not always being set causing troubles.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Rather than scanning on boot, scan upon the first attempt to check the
badness of a block. This speeds up boot when not using NAND, and reduces
the likelihood of needing to reflash via JTAG if NAND becomes
nonfunctional.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Implement block-skipping read/write, based on a patch from
Morten Ebbell Hestens <morten.hestnes@tandberg.com>.
Signed-off-by: Morten Ebbell Hestnes <morten.hestnes@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The hardware has separate registers for block and page-within-block,
but the division between the two has no apparent relation to the
actual erase block size of the NAND chip.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is a driver for the Flash Control Machine of the enhanched Local Bus
Controller found on some Freescale chips (such as the mpc8313 and the
mpc8379).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Some hardware, such as the enhanced local bus controller used on some
mpc83xx chips, does ecc transparently when reading and writing data, rather
than providing a generic calculate/correct mechanism that can be exported to
the nand subsystem.
The subsystem should not BUG() when calculate, correct, or hwctl are
missing, if the methods that call them have been overridden.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch turns off printing of bad blocks per default upon bootup.
This can always be shown via the "nand bad" command later.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes nand_wait_ready() to not just call nand_wait(),
since this will send a new command to the NAND chip. We just want to
wait for the chip to become ready here.
Signed-off-by: Stefan Roese <sr@denx.de>
- Fixing leading white spaces
- Fixing indentation where 4 spaces are used instead of tab
- Removing C++ comments (//), wherever I introduced them
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When building the 8544DS board we get this error:
In file included from r8a66597-hcd.c:22:
u-boot/include/usb.h:190:2: error: #error USB Lowlevel not defined
make[1]: *** [r8a66597-hcd.o] Error 1
The cleanest fix is to only build r8a66597-hcd.c if CONFIG_USB_R8A66597_HCD
is set.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The block and page parameters of onenand_verify_page() are not used. This causes a compiler error when CONFIG_MTD_ONENAND_VERIFY_WRITE is enabled.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
FILL_15BIT_555RGB macro extension for pixel swapping
by commit bed53753dd
introduced a bug in cfb_console:
Bitmaps with odd-numbered width won't be rendered
correctly and even U-Boot crashes are observed on
some platforms while repeated rendering of such
bitmaps with "bmp display". Also if a bitmap is
rendered to an odd-numbered x starting position,
the same problem occurs. This patch is an attempt
to fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
If logo_plot() should ever be called with x starting
position other than zero and for pixel depths greater
than 8bpp, logo colors distortion will be observed.
This patch fixes the issue.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The CFI driver allowed only for static initializers in the
CFG_FLASH_BANKS_LIST definition, i. e. it did not allow to map
several flash banks contiguously if the bank sizes were not known in
advance, which kind of violates U-Boot's design philosophy.
(will be used for example by the TQM8xxL boards)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add MII commands to the UEC driver. Note that once a UEC device is selected,
any device on its MDIO bus can be addressed.
Signed-off-by: David Saada <david.saada@ecitele.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
add support for Renesas R8A66597 usb controller.
This patch supports USB Host mode.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Add support to drivers/usb/usbdcore_omap1510.c for OMAP5912 and OMAP16xx devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Some of the flash memories produced by ATMEL start in read-only mode.
We need to unprotect it. This patch allows the AT49BV6416 to work with
cfi_flash memories. Tested in the at91rm9200ek board.
Signed-off-by: Rafael Campos Las Heras <rafael.campos@hanscan.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The Atmel lcd controller is used on Atmel's AT91 (little endian) and
AVR32 (big endian) platforms.
As such, the controller can handle both big and little endian memory.
This patch fixes the driver for the AVR32 platform.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
The current implementation of get_timer() is only really useful after we
have relocated u-boot to memory. The i2c code is used before that as part
of the SPD DDR setup.
We actually have a bug when using the get_timer() code before relocation
because the .bss hasn't been setup and thus we could be reading/writing
a random location (probably in flash).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prevent i2c_init() in fsl_i2c.c from writing to the data segment before
relocation. Commit d8c82db4 added the ability for i2c_init() to program the
I2C bus speed and save the value in i2c_bus_speed[], which is a global
variable. It is an error to write to the data segment before relocation,
which is what i2c_init() does when it stores the bus speed in i2c_bus_speed[].
Signed-off-by: Timur Tabi <timur@freescale.com>
This got broken by commits 93c56f212c
[cfi_flash: support of long cmd in U-boot.]
That command needs to be in little endian format on BE machines
with CFG_WRITE_SWAPPED_DATA. Without this patch, the command 0xf0
gets saved on stack as 0x00 00 00 f0 and 0x00 gets written into
the cmdbuf in case portwidth = chipwidth = 8bit.
Cc: Alexey Korolev <akorolev@infradead.org>
Cc: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Round the serial port clock divisor value returned by
calc_divisor()
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
This got changed by commit 93c56f212c
[cfi_flash: support of long cmd in U-boot.]
Long is the wrong type because it will behave differently on 64bit
machines in a way that is probably not expected. u32 should be
enough.
Cc: Alexey Korolev <akorolev@infradead.org>
Cc: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Add function of new PCI, pci_skip_dev and pci_print_dev.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We need to wait while drawing engine clears frame
buffer before any further software accesses to frame
buffer will be initiated. Otherwise software drawn
parts could be partially destroyed by the drawing
engine or even GDC chip freeze could occur (as
observed on socrates board).
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Clean Makefile
Move device specific values to driver for better reading
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stefan Roese <sr@denx.de>
Redesign uartlite driver to in_be32 and out_be32 macros
Fix missing header in io.h
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The formula "counter = (u32) (gd->bus_clk / gd->baudrate) / 32"
can generate the wrong divisor due to integer division truncation.
Round the calculated divisor value by adding 1/2 the baudrate
before dividing by the baudrate.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Some boards based on AT91SAM926X-EK use smaller DF chips to keep
bootstrap, u-boot and its environment, using NAND or other external
storage for kernel and rootfs. This patch adds support for
small 1024x263 chip.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
This patch fixes bugs in usbdcore*.c related to the use of devices
with multiple configurations.
The original code made mistakes about the meaning of configuration value and
configuration index, and the resulting off-by-one errors resulted in:
* SET_CONFIGURATION always selected the first configuration, no matter what
wValue is being passed.
* GET_DESCRIPTOR/CONFIGURATION always returned the descriptor for the first
configuration (index 0).
Signed-off-by: Harald Welte <laforge@openmoko.org>
Acked-by: Markus Klotzbuecher <mk@denx.de>
This patch fixes NAND related printf format warning. Those warnings are
now visible since patch dc4b0b38d4
[Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is
really helpful.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves the check, if a device should be skipped in PCI PNP
configuration into the function pci_skip_dev(). This function is defined
as weak so that it can be overwritten by a platform specific one if
needed. The check if the device should get printed in the PCI summary upon
bootup (when CONFIG_PCI_SCAN_SHOW is defined) is moved to the function
pci_print_dev() which is also defined as weak too.
Signed-off-by: Stefan Roese <sr@denx.de>
This PCI-X e1000 variant works by just adding in the correct
PCI IDs in the appropriate places.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Round the serial port clock divisor value returned by
calc_divisor().
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: John Roberts <john.roberts@pwav.com>
This is particularly problematic now that non-NAND-specific code is
including <nand.h>, and thus all debugging code is being compiled
regardless of whether it was requested, as reported by Scott McNutt
<smcnutt@psyent.com>.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This makes it easier to use the driver on other platforms.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
In order to consolidate more of the various MMC drivers around the
tree, we must first have a common place to put them.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
As pointed out by Jerry Hicks, this patch corrects the device ID of
the Spansion AM29DL800BB NOR device. Verified against latest Spansion
datasheet (rev C4 from Dezember 2006).
Signed-off-by: Stefan Roese <sr@denx.de>
Remove duplicate definitions in include/lxt971a.h.
Remove duplicate registers and bits definitions in
include/lxt971a.h for standard MII registers, and
use values in include/miiphy.h instead.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Renesas SH7763 has 2 channel Ethernet device.
This is 10/100/1000 Base support.
But this patch check 10/100 Base only.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
If enable DEBUG, can not compile ne2000 driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The driver need wait for the device updating signature to host.
If we don't wait for it, the driver can not detect the device(disk)
when the system powers up.
Signed-off-by: Dave Liu <daveliu@freescale.com>
This patch simplifies flash_toggle() (AMD commandset), which is used to
detect if a FLASH device is still busy with erase/program operations. On
800MHz Canyonlands/Glacier boards (460EX/GT) the current implementation
did not detect the busy state reliably, resulting in non erased sectors
etc. This patch now simplifies this function by "just" comparing the
complete data-word instead of ANDing it with the command-word (0x40)
before the compatison. It is done the same way in the Linux implementation
chip_ready() in cfi_cmdset_0002.c.
Signed-off-by: Stefan Roese <sr@denx.de>
LAWs have the concept of priority so its useful to be able to allocate
the lowest (highest number) priority. We will end up using this with the
new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make it so we keep track of which LAWs have allocated and provide
a function (set_next_law) which can allocate a LAW for us if one is
free.
In the future we will move to doing more "dynamic" LAW allocation
since the majority of users dont really care about what LAW number
they are at.
Also, add CONFIG_MPC8540 or CONFIG_MPC8560 to those boards which needed them
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds basic support for the TQM8548 module from TQ-Components
(http://www.tqc.de/) including DDR2 SDRAM initialisation and support for
eTSEC 3 and 4
Furthermore Flash buffer write has been enabled to speed up output to
the Flash by approx. a factor of 10.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
This is a re-write of the NAND FSL UPM driver using the more universal
hwcontrol callback (instead of the cmdfunc callback). Here is a brief
list of furher modifications:
- For the time being, the UPM setup writing the UPM array has been
removed from the driver and must now be done by the board specific
code.
- The bus width definition in "struct fsl_upm_nand" is now in bits to
comply with the corresponding Linux driver and 8, 16 and 32 bit
accesses are supported.
- chip->dev_read is only set if fun->dev_ready != NULL, which is
required for boards not connecting the R/B pin.
- A few issue have been fixed with MxMR bit manipulation like in the
corresponding Linux driver.
Note: I think the "io_addr" field of "struct fsl_upm" could be removed
as well, because the address is already determined by
"nand->IO_ADDR_[RW]", but I'm not 100% sure.
This patch has been tested on a TQM8548 modules with the NAND chip
Micron MT29F8G08FABWP.
This patch is based on the following patches posted to this list a few
minutes ago:
PPC: add accessor macros to clear and set bits in one shot
83xx/85xx/86xx: add more MxMR local bus definitions
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
This was configured to use the deprecated CONFIG_OF_FLAT_TREE, change
to CONFIG_OF_LIBFDT.
WARNING: This conversion is untested because I do not have a board to
test it on.
NOTE: The FDT blob (DTS) must have an /aliases/ethernet0 and (optionally)
/aliases/ethernet1 property for the ethernet to work.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
SH7763 has 3 SCIF channels. SCIF0 and 1 are same register constitution,
but only SCIF2 is different. This patch work all SCIF channel.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
According to the Application Notes of the DM9000, only the 2 bits 0:1 of
the status byte need to be checked to identify a valid packet in the fifo
But, The several different Application Notes do not all speak the same
language on these bits. They do not disagree, but only 1 Application Note
noted explicitly that only these 2 bits need to be checked.
Even the datasheets do not mention anything about these 2 bits.
Because the old code, and the kernel check the whole byte, I left this piece
untouched.
However, I tested all board/DM9000[A|E|EP] devices with this 2 bit check, so
it should work.
Notice, that the 2nd iteration through this receive loop (when a 2nd packet is
in the fifo) is much shorter now, compared to the older U-boot driver code,
so that we can maybe run into a hardware condition now that was never seen
before, or maybe was seen very unfrequently.
Additionaly added a cleanup of a stack variable.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
A last minute cleanup before submitting the DM9000A patch series yesterday introduced
a bug in reading the rx-status registers in 32bit mode only.
This patch repairs this.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Some lines of the U-boot DM9000x driver are longer than 80 characters, or
need some other minor cleanup.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The DM9000A network controller does not work with the U-boot DM9000x driver.
Analysis showed that many incoming packets are lost.
The DM9000A Application Notes V1.20 (section 5.6.1) recommend that the poll to
check for a valid rx packet be done on the interrupt status register, not
directly by performing the dummy read and the rx status check as is currently
the case in the u-boot driver.
When the recommended poll is done as suggested the driver starts working
correctly on 10Mbit/HD, but on 100MBit/FD packets come in faster so that there
can be more than 1 package in the fifo at the same time.
The driver must perform the rx-status check in a loop and read and handle all
packages until there is no more left _after_ the interrupt RX flag is set.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
According to the application notes of the DM9000 v1.22 chapter 5.2 bullet 2, the
reset procedure must be done twice to properly reset the DM9000 by means of software.
This errata is not needed anymore for the DM9000A, but it does not bother it.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The eth_send routine of the U-boot DM9000x driver does not match the
DM9000 or DM9000A application notes/programming guides.
This change improves the stability of the DM9000A network controller.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
It seems that the debugging code of the DM9000x driver in U-boot has not been
compiled for a long time, because it cannot compile...
Also rearranged some loglines to get more useful info while debugging.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The U-boot DM9000x driver contains a compile time bus-width definition for
the databus connected to the network controller.
This compile check makes the code unclear, inflexible and is unneccessary.
It can be asked to the network controller what its bus-width is by reading bits
6 and 7 of the interrupt status register.
The linux kernel already uses a runtime mechanism to determine this bus-width,
so the implementation below looks somewhat like that implementation.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Added new command set ID. Buffered write command processing is changed
in order to support M18 flash chips family.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
Some NOR flash chips needs support of commands with length grether than max
value size of uchar. For example all M18 family chips use 0x1ff command in
buffered write mode as value of program loops count.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
On AD7414 the first value upon bootup is not read correctly.
This is most likely because of the 800ms update time of the
temp register in normal update mode. To get current values
each time we issue the "dtt" command including upon powerup
we switch into one-short mode.
This patch fixes the problem on AD7414 equipped boards (Sequoia,
Canyonlands etc), that temp value printed in the bootup log was
incorrect.
Signed-off-by: Stefan Roese <sr@denx.de>
This adds a new SPI flash subsystem.
Currently, only AT45 DataFlash in non-power-of-two mode is supported,
but some preliminary support for other flash types is in place as
well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This adds a driver for the SPI controller found on most AT91 and AVR32
chips, implementing the new SPI API.
Changed in v4:
- Update to new API
- Handle zero-length transfers appropriately. The user may send a
zero-length SPI transfer with SPI_XFER_END set in order to
deactivate the chip select after a series of transfers with chip
select active. This is useful e.g. when polling the status
register of DataFlash.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch gets rid of the spi_chipsel table and adds a handful of new
functions that makes the SPI layer cleaner and more flexible.
Instead of the spi_chipsel table, each board that wants to use SPI
gets to implement three hooks:
* spi_cs_activate(): Activates the chipselect for a given slave
* spi_cs_deactivate(): Deactivates the chipselect for a given slave
* spi_cs_is_valid(): Determines if the given bus/chipselect
combination can be activated.
Not all drivers may need those extra functions however. If that's the
case, the board code may just leave them out (assuming they know what
the driver needs) or rely on the linker to strip them out (assuming
--gc-sections is being used.)
To set up communication parameters for a given slave, the driver needs
to call spi_setup_slave(). This returns a pointer to an opaque
spi_slave struct which must be passed as a parameter to subsequent SPI
calls. This struct can be freed by calling spi_free_slave(), but most
driver probably don't want to do this.
Before starting one or more SPI transfers, the driver must call
spi_claim_bus() to gain exclusive access to the SPI bus and initialize
the hardware. When all transfers are done, the driver must call
spi_release_bus() to make the bus available to others, and possibly
shut down the SPI controller hardware.
spi_xfer() behaves mostly the same as before, but it now takes a
spi_slave parameter instead of a spi_chipsel function pointer. It also
got a new parameter, flags, which is used to specify chip select
behaviour. This may be extended with other flags in the future.
This patch has been build-tested on all powerpc and arm boards
involved. I have not tested NIOS since I don't have a toolchain for it
installed, so I expect some breakage there even though I've tried
fixing up everything I could find by visual inspection.
I have run-time tested this on AVR32 ATNGW100 using the atmel_spi and
DataFlash drivers posted as a follow-up. I'd like some help testing
other boards that use the existing SPI API.
But most of all, I'd like some comments on the new API. Is this stuff
usable for everyone? If not, why?
Changed in v4:
- Build fixes for various boards, drivers and commands
- Provide common struct spi_slave definition that can be extended by
drivers
- Pass a struct spi_slave * to spi_cs_activate and spi_cs_deactivate
- Make default bus and mode build-time configurable
- Override default SPI bus ID and mode on mx32ads and imx31_litekit.
Changed in v3:
- Add opaque struct spi_slave for controller-specific data associated
with a slave.
- Add spi_claim_bus() and spi_release_bus()
- Add spi_free_slave()
- spi_setup() is now called spi_setup_slave() and returns a
struct spi_slave
- soft_spi now supports four SPI modes (CPOL|CPHA)
- Add bus parameter to spi_setup_slave()
- Convert the new i.MX32 SPI driver
- Convert the new MC13783 RTC driver
Changed in v2:
- Convert the mpc8xxx_spi driver and the mpc8349emds board to the
new API.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Tested-by: Guennadi Liakhovetski <lg@denx.de>
* The cfi_flash.c memset fix actual allows the board to boot so there is
a bit more going on here than just resolving warnings associated with
uninitialized variables.
* include/asm/bitops.h:302: warning: '__swab32p' is static but used in
inline function 'ext2_find_next_zero_bit' which is not static
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add new configuration variable CONFIG_PCI_OHCI_DEVNO.
In case of several PCI USB controllers on a board this variable
specifys which controller to use.
Also add USB support for sokrates board.
See doc/README.generic_usb_ohci for details.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds support for the ATMEL LCDC driver which is used on some
AT91 and AVR platforms.
Is has been tested with the AT91CAP9ADK, AT91SAM9261EK, AT91SAM9263EK and
AT91SAM9RLEK boards. Adaptation for AVR32 should probably be easy.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Physical addrs need to be represented by phys_addr_t, not
unsigned long. Otherwise, systems that use CONFIG_PHYS_64BIT
are going to fail mightily.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
When applying the AT91CAP9 patches upstream, something transformed
the '@' character into the ' <at> ' sequence.
The patch below restores the original form in all the places where
it has been modified (the AT91CAP9 files, the AT91SAM9260 files which
were copied from AT91CAP9, and a couple of other files where the
' <at> ' sequence was present).
Signed-off-by: Stelian Pop <stelian@popies.net>
When applying the AT91CAP9 patches upstream, something transformed
the '@' character into the ' <at> ' sequence.
The patch below restores the original form in all the places where
it has been modified (the AT91CAP9 files, the AT91SAM9260 files which
were copied from AT91CAP9, and a couple of other files where the
' <at> ' sequence was present).
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The Vitesse VSC8601 RGMII PHY has internal delay for both Rx
and Tx clock lines. They are configured using 2 bits in extended
register 0x17.
Therefore CFG_VSC8601_SKEW_TX and CFG_VSC8601_SKEW_RX have
been introduced with valid values 0-3 giving 0.0, 1.4,1.7 and 2.0ns delay.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
--
drivers/net/tsec.c | 6 ++++++
drivers/net/tsec.h | 3 +++
2 files changed, 9 insertions(+), 0 deletions(-)
This patch fixes a problem with the month being read and written
incorrectly (offset by one). This only gets visible by also using
the Linux driver (rtc-m41t80).
Tested on AMCC Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
Onenand needs a version of memcpy() which performs 16 bit accesses
only; make sure the name does not conflict with the standard
function.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The ethernet hang is caused by receiving buffer in DRAM is not
yet ready due to access cycles require longer time in DRAM.
Relocate DMA buffer descriptors from DRAM to internal SRAM.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Move non-inlied functions into specific drivers file
Set get_prom as weak
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Remove a redundant register definition, clean up some coding style
violations.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds a configurable flash auto protection list that can be used
to make U-Boot protect flash regions in flash_init().
The idea has been discussed on the u-boot mailing list starting
on Nov 18th, 2007.
Even this patch brings a new feature it is used as a bugfix for 4xx
platforms where flash_init() does not completely protect the
monitor's flash range in all situations.
U-Boot protects the flash range from CFG_MONITOR_BASE to
(CFG_MONITOR_BASE + monitor_flash_len - 1) by default. This does not
include the reset vector at 0xfffffffc.
Example:
#define CFG_FLASH_AUTOPROTECT_LIST {{0xfff80000, 0x80000}}
This config option will auto protect the last 512k of flash that
contains the bootloader on board like APC405 and PMC405.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch correctly sets the oobavail variable
and fixes a bug where the oob data was not valid when
there where multiple groups in oobfree.
First segment fixes a typo
Second segment fixes a bug where oob data may be copied incorrectly.
Third segment adds an error message when exiting due to write protect.
Forth segment fixes a bug where oobavail may be set incorrectly.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
MC13783 is a multifunction IS with an SPI interface to the host. This
driver handles the RTC controller in this chip.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This is an SPI driver for i.MX and MXC based SoCs from Freescale. So far
only implemented and tested on i.MX31, can with a modified register layout
and definitions be used for i.MX27, I think, MXC CPUs have similar SPI
controllers too.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch removes the board dependent parts from
"drivers/mtd/dataflash.c".
Each board relying on this, will have the appropriate
code in a new file, "partition.c" in the board directory.
board Makefiles updated to use the file.
The dataflash partitions are aligned on sector/page boundaries.
The CONFIG_NEW_DF_PARTITION was used to create named partitions
This is now the default operation, and the CONFIG variable is removed.
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
There are two NAND entries with ID 0xDC and this obviously causes problems.
In the kernel, they punted the first entry, so we should do the same.
See this upstream e-mail for more info:
http://lists.infradead.org/pipermail/linux-mtd/2007-July/018795.html
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Current libata.h of u-boot is out of sync from linux kernel,
this patch make it be consistent with linux kernel.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Tor Krill <tor@excito.com>
It should access with 16-bit instead of 8-bit
Now it uses the generic memcpy with 8-bit access. It means it reads wrong data from OneNAND.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Remove test for CONFIG_MPC5200 in drivers/pci/pci_auto.c and define
CONFIG_PCIAUTO_SKIP_HOST_BRIDGE in related board configuration files.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
When the LM73 temperature sensor measures a temperature below 0 C, the
current driver does not perform sign extension, so the result returned is
512 C too high. This patch fixes the problem, and does general cleanup
of the code.
Signed-off-by: Larry Johnson <lrj@acm.org>
Some NOR flash chip from Spansion, for example, the s29ws-n MirrorBit
series require different addresses for buffered write commands. Define a
configuration option to support buffered writes on those chips. A more
elegant solution would be to automatically detect those chips by parsing
their CFI records, but that would require introduction of a fixup table
into the cfi_flash driver.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch makes SPARC/LEON processors able to read and write
to the SMC91111 chip using the chip external I/O bus of the memory
controller. This patchs defines the standard in and out macros
expected by the SMC9111 driver.
To access that I/O bus one must set up the memory controller
(MCTRL or FTMCTRL) correctly. It is assumed that the user sets
up this correctly when the other MCTRL parameters are set up. It
can be set up from the board configuration header file.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
DataFlash partition information has become a mess. This patch
defines a single partition scheme for Atmel DataFlashes. This partition
scheme will be used by all AT91CAP9 and AT91SAM9 boards.
Signed-off-by: Stelian Pop <stelian@popies.net>
This patch adds a driver for the following smsc network controllers:
LAN9115
LAN9116
LAN9117
LAN9215
LAN9216
LAN9217
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Add 82541ER device with latest integrated IGP2 PHY.
Introduced CONFIG_E1000_FALLBACK_MAC for NIC bring-up with empty eeprom.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
GRETH is an Ethernet 10/100 or 10/100/1000 MAC with out without
a debug link (EDCL). The GRETH core is documented in GRIP.pdf
available at www.gaisler.com.
If the GRETH has GigaBit support (GBIT, Scatter gather, checksum
offloading etc.) can be determined by a bit in the control register.
The GBIT MAC is supported by operating in GRTEH 10/100 legacy mode.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
SPARC has implemented __raw_readq, it reads 64-bit from any 32-bit address.
SPARC CPUs implement flash_read64 which calls __raw_readq.
For current SPARC architectures (LEON2 and LEON3) each read from the
FLASH must lead to a cache miss. This is because FLASH can not be set
non-cacheable since program code resides there, and alternatively disabling
cache is poor from performance view, or doing a cache flush between each
read is even poorer.
Forcing a cache miss on a SPARC is done by a special instruction "lda" -
load alternative space, the alternative space number (ASI) is processor
implementation spcific and can be found by including <asm/processor.h>.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Add entry for 512Kx16 AMD flash to jedec_table.
Read out 16bit device id if chipwidth is 16bit.
Fixed coding style after Stefans feedback
Signed-off-by: Tor Krill <tor@excito.com>
Receive FIFO level register is different in SH4A.
Because register is different, cannot occasionally receive data.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SH7780 is CPU of Renesas Technology.
This CPU has
- CPU clock 400MHz
- PCI support
- DDR-SDRAM controller
- etc ...
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support to the Freescale I2C driver (fsl_i2c.c) for setting and querying
the I2C bus speed. Current 8[356]xx boards define the CFG_I2C_SPEED macro,
but fsl_i2c.c ignores it and uses conservative value when programming the
I2C bus speed.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Add the Freescale on-chip SATA controller driver to u-boot,
The SATA controller is used on the 837x and 8315 targets,
The driver can be used to load kernel, fs and dtb.
The features list:
- 1.5/3 Gbps link speed
- LBA48, LBA28 support
- DMA and FPDMA support
- Two ports support
Signed-off-by: Dave Liu <daveliu@freescale.com>
original ata_piix driver is using IDE framework, not real
SATA framework. For now, the ata_piix driver is only used
by x86 sc520_cdp board. This patch makes the ata_piix driver
use the new SATA framework, so
- remove the duplicated command stuff
- remove the CONFIG_CMD_IDE define in the sc520_cdp.h
- add the CONFIG_CMD_SATA define to sc520_cdp.h
Signed-off-by: Dave Liu <daveliu@freescale.com>
move the cmd_sata.c from common/ to drivers/ata_piix.c,
the cmd_sata.c have some part of ata_piix controller drivers.
consolidate the driver to have better framework.
Signed-off-by: Dave Liu <daveliu@freescale.com>
The default settings for RTC DS1337 keeps the OSC
output, 32,768 Hz, on. This add CFG_RTC_DS1337_NOOSC to
turn it off.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
RTL8211B sets link state register after autonegotiation complete,
so with bootdelay=0 RTL8211B will report lack of the link.
To fix this, we should wait for aneg to complete, even if the
link is currently down.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds basic support for Broadcom BCM5481 PHY.
RXD-RXC delay quirk comes from MPC8360E-RDK BSP source, author is
Peter Barada <peterb@logicpd.com>.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
The Vitesse VSC7385 is a 5-port switch found on the Freescale MPC8349E-mITX
and other boards. A small firwmare must be uploaded to its on-board memory
before it can be enabled. This patch adds the code which uploads firmware
(but not the firmware itself).
Previously, this feature was provided by a U-Boot application that was
made available only on Freescale BSPs. The VSC7385 firmware must still
be obtained separately, but at least there is no longer a need for a separate
application.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Flex-OneNAND is a monolithic integrated circuit with a NAND Flash array
using a NOR Flash interface. This on-chip integration enables system designers
to reduce external system logic and use high-density NAND Flash
in applications that would otherwise have to use more NOR components.
Flex-OneNAND enables users to configure to partition it into SLC and MLC areas
in more flexible way. While MLC area of Flex-OneNAND can be used to store data
that require low reliability and high density, SLC area of Flex-OneNAND
to store data that need high reliability and high performance. Flex-OneNAND
can let users take advantage of storing these two different types of data
into one chip, which is making Flex-OneNAND more cost- and space-effective.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
AX88796L is device of NE2000 compatible.
This patch support AX88796L ethernet device.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There are more devices of the NE2000 base.
A present code is difficult for us to support more devices.
To support more NE2000 clone devices, separated the function.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Blackfin on-chip MAC driver was being managed in the BF537-STAMP board
directory, but it is not board specific, so relocate it to the drivers dir
so that other Blackfin ports can utilize it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the "ssync" instruction may have hardware anomalies associated with
it, have the smc91111 driver use the SSYNC macro rather than invoking it
directly. We workaround all the anomalies via this macro.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If the LWMON5 config has SYSMON POST among CONFIG_POSTs which may be
run on the board, then the SYSMON POST controls the display backlight
(doesn't switch backlight ON if POST FAILED, and does switch the
backlight ON if PASSED).
If not, then the video driver controls the display backlight (just
switch ON the backlight upon initialization).
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
In current source code, when the device number of PCI is 0, process PCI
bridge without fail. However, when the device number is 0, it is not PCI
always bridge. There are times when device of PCI allocates.
When CONFIG_PCI_SKIP_HOST_BRIDGE is enable, this problem is solved when
use this patch.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Stefan Roese <sr@denx.de>
Modify the RTC API to provide one a status for the time reported by
the rtc_get() function:
0 - a reliable time is guaranteed,
< 0 - a reliable time isn't guaranteed (power fault, clock issues,
and so on).
The RTC chip drivers are responsible for providing this info if the
corresponding chip supports such functionality. If not - always
report that the time is reliable.
The POST RTC test was modified to detect the RTC faults utilizing
this new rtc_get() feature.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
With this patch we don't need that many #ifdef's in the code. It moves
the subtraction into the macro and defines a NOP-macro when
CONFIG_FLASH_SHOW_PROGRESS is not defined.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
This patch adds CFG_OHCI_USE_NPS to the common USB-OHCI driver. This
way a board just needs to define this new option to enable the "force
NoPowerSwitching mode" instead of adding new CPU/architecture defines
to the USB source itself.
This new option will be used first with the new AMCC 460EX Canyonlands
board port, which will be posted in a few days.
This patch also fixes a small compilation problem when DEBUG is enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
When rtl_recv() of rtl8169 is called, OWNbit of status register
is not enable occasionally.
rtl_recv() doesn't work normally when the driver doesn't do
appropriate processing.
This patch fix this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
allow u-boot to recover (and, e.g., switch to another interface) in the
case where a PHY does not report autonegotiation is complete within its
two second timeout value.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fix a typo in qe_upload_firmware() that prevented uploading firmware on
systems with more than one RISC core.
Signed-off-by: Timur Tabi <timur@freescale.com>
erratum 5.6 states the autoneg completion bit is functional only if the
autoneg bit is asserted.
This fixes any secondarily-issued networking commands on non-gigabit
links on the mpc8360 mds board.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When the LM75 temperature sensor measures a temperature below 0 C, the
current driver does not perform sign extension, so the result returned is
256 C too high. This patch fixes the problem.
Signed-off-by: Larry Johnson <lrj@acm.org>
