The initial training for the DDRC may provide results that are not
optimized. The workaround provides better read timing margins.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Per the latest erratum document, update step 4 and step 8, only
DEBUG_29[21] is changed, all other bits should not be changed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The code uses a lot of signed numbers, which ended up in variables
of unsigned type, which resulted in all sorts of underflows. This
in turn caused incorrect calibration on certain boards. Moreover,
repair the readout of the DQ delay, which was being pulled from
wrong register.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Just staticize global variables in sequencer, since there is no
point in having these symbols available outside of the DDR code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Originally, the DLEVEL selects the debug level within the sequencer code,
but only displays the messages on that particular debug level. Tweak the
handling such that for particular debug level, debug messages on that
level and lower are displayed. This allows better regulation of debug
message verbosity.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
This one last set of delay configuration registers was not properly
zeroed out originally, fix it and zero them out.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
There is no point in resetting the ODT setting if the write test
failed, since the code will always retry the calibration and thus
reconfigure the ODT anyway OR the code will fail calibration and
halt.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Every invocation of the scc_mgr_set_dqs_en_delay_all_ranks() is
followed by SCC manager update. Moreover, only this function
triggers the SCC manager update internally. Thus, remove the
internal invocation to avoid triggering the update twice.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
The hi address bitfield in the protection rule must be set to
the last address in the region which the rule represents. The
behavior is now in-line with code generated by Quartus 15.1 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
The code should be setting registers to zero, not one register to value.
Swap the order of arguments to correct the behavior. The behavior is now
in-line with code generated by Quartus 15.1 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
In the most unlikely case the DQS tracking was to be disabled,
make sure we do not errornously re-enable it. Note that DQS
tracking is enabled on all systems observed thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
The bit 22 is in fact DQS tracking enable bit (dqstrken) and there
is a macro for this bit already, so use it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Minor change: chosen is written with one "o".
No code change here, only comment & printf.
Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Armada 38x has a maximum of two cores. Probably copy/paste
bug from Armada XP.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
During initial DDR training, false parity errors may be detected.
This patch adds workaround to fix the erratum.
Tested on LS2085QDS and LS2080RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Following commit 61bd2f75, exclude unused DDR controller from
calculating RAM size for SPL boot.
Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During the receive data training, the DDRC may complete on a
non-optimal setting that could lead to data corruption or
initialization failure.
Workaround: before setting MEM_EN, set DEBUG_29 register with
specific value for different data rates.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
This should make it clear that this symbol is meant to be defined by
board headers.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If MV_DEBUG_WL is defined, DEBUG_WL_S and DEBUG_WL_D macros are missing.
In addition to that, get rid of debug output printing non-existent
counter variable.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, ECC support is enabled for all Armada XP boards. So the
DDR3 driver tries to configure the controller with ECC support, even
on boards without ECC. This patch makes this ECC optional which now
can be configured on a board-per-board basis.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>
gcc 5.1 generates this new warning (for Armada 38x platforms):
drivers/ddr/marvell/a38x/ddr3_debug.c: In function 'hws_ddr3_tip_read_training_result':
drivers/ddr/marvell/a38x/ddr3_debug.c:177:40: warning: 'sizeof' on array
function parameter 'result' will return size of 'enum hws_result (*)[1]' [-Wsizeof-array-argument]
memcpy(result, training_result, sizeof(result));
^
drivers/ddr/marvell/a38x/ddr3_debug.c:171:31: note: declared here
u32 dev_num, enum hws_result result[MAX_STAGE_LIMIT][MAX_INTERFACE_NUM])
^
Since this functions is not referenced anywhere, lets just remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
As the errata A008336 and A008514 do not apply to all LS series SoCs
(such as LS1021A, LS1043A) we move them to an soc specific file
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0,
T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on
LS102x Rev2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.
Signed-off-by: York Sun <yorksun@freescale.com>
The workaround requires different setting for range 1 vs 2.
Also adjust timeout value for waiting for controller to be idle.
Signed-off-by: York Sun <yorksun@freescale.com>
BIST test code has a typo, resulting the binding registers not
maintained as expected. This typo results BIST runs twice on
the covered memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Reported-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of
reset. It can be configured to disable one controller. To support this
operation, the driver needs to detect and skip the disabled controller.
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
SAR1_CPU_CORE_MASK was wrong, probably copy/paste
from another architecture.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support. Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM. If this needs to be done, it should be
handled in the board file, not in core code.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Fix the following problem:
drivers/ddr/altera/sequencer.c: In function 'sdram_calibration_full':
drivers/ddr/altera/sequencer.c:1943:25: warning: 'found_failing_read' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (found_passing_read && found_failing_read)
^
drivers/ddr/altera/sequencer.c:1803:26: note: 'found_failing_read' was declared here
u32 found_passing_read, found_failing_read, initial_failing_dtap;
^
Signed-off-by: Marek Vasut <marex@denx.de>
This gem is really really rare, there was an actual float used in
the Altera DDR init code, which pulled in floating point ops from
the libgcc, just wow.
Since we don't support floating point operations the same way Linux
does not support them, replace this with an integer multiplication
and division combo. This removes some 2kiB of size from the SPL as
the floating point ops are no longer pulled in from libgcc.
This was detected by enabling CONFIG_USE_PRIVATE_LIBGCC=y , which
does not contain the floating point bits.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch introduces the SDRAM scrubbing for ECC enabled board
to fill/initialize the ECC bytes. This is done via the XOR engine
to speed up the process. The scrubbing is a 2-stage process:
1) SPL scrubs the area 0 - 0x100.0000 (16MiB) for the main U-Boot
2) U-Boot scrubs the remaining SDRAM area(s)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This is tested on the DB-MV784MP-GP eval board. To really enable ECC
support on this board the I2C EEPROM needs to get changed. As it
saves the enabling of ECC support internally. For this the following
commands can be used to enable ECC support on this board:
Its recommended for first save (print) the value(s) in this EEPROM
address:
=> i2c md 4e 0.1 2
0000: 05 00 ..
To enable ECC support you need to set bit 1 in the 2nd byte:
Marvell>> i2c mw 4e 1.1 02
Marvell>> i2c md 4e 0.1 2
0000: 05 02 ..
To disable ECC support again, please use this command:
Marvell>> i2c mw 4e 1.1 00
Marvell>> i2c md 4e 0.1 2
0000: 05 00 ..
On other AXP boards, simply plugging an ECC DIMM should be enough to
enable ECC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Fix most of the dangling checkpatch issues, no functional change.
There are still 7 warnings, 1 checks , but those are left in place
for the sake of readability of the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_misc_config
instead of the various macros. This is just an sed exercise here, no
manual coding needed.
This patch actually removes the need to include any board-specific
files in sequencer.c , so sequencer.c namespace is now no longer
poluted by QTS-generated macros.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This is another macro used to obfuscate the real code. The
T(INIT|RESET)_CNTR._VAL is always defined, so this indirection
is unnecessary. Get rid of this.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Just use READ_VALID_FIFO_SIZE directly, no need for this macro obfuscation.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_io_config
instead of the IO_* macros. This is just an sed excercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_rw_mgr_config
instead of the RW_MGR_* macros. This is just an sed exercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager
configuration values in board file. Introduce a complementary function,
socfpga_get_sdram_rwmgr_config(), which returns this the structure.
This is another step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce two wrapper functions, socfpga_get_seq_ac_init() and
socfpga_get_seq_inst_init() to avoid direct inclusion of the
sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS
generated files. This reduces namespace pollution again.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This is defined in the QTS-generated headers, so it must not be
re-defined in sequencer.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
These parameters are not used in the code, zap them and the
macros which are used by them as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Move the files generated by QTS into the board directory, they should not
be part of the driver files at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Originally, both sdram_start and sdram_end were 64b values. The
sdram_start had no reason for being so, since our address space
is only 32b, so switching sdram_start to u32 is simple.
The sdram_end is a bit more complex, since it can actually be
set to (1 << 32) if someone really wanted to use an SoCFPGA with
4 GiB of DRAM and fixed the code around a little. But, the code
handling the protection rules internally decrements the sdram_end
variable anyway. Thus, instead of calling the code and passing in
the address of the SDRAM end, pass in the address already decremented
by one. This lets the sdram_end be 32b as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean the function up so that it's obvious what it is doing,
fix the formating strings in debug outputs, add kerneldoc.
Make the function return proper errno-compliant return values
and propagate this change throughout sdram.c
Signed-off-by: Marek Vasut <marex@denx.de>
Clean up coding style, mostly clean up comments, add kerneldoc.
Also, zap assignment of the "cs" variable, which is outright
dead code, so just remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Pluck out all of the CONFIG_HPS_SDR_CTRLCFG_* macros. This change
makes sdram.c completely clear of these macros and allows removing
of the ugly include of sdram.h . The namespace is now a much nicer
place!
Signed-off-by: Marek Vasut <marex@denx.de>
Introduce socfpga_sdram_get_config() function implement in a board file,
which returns the socfpga_sdram_config structure. This is the last step
in cleaning up the socfpga_mmr_init_full(), but not the last step which
allows removing the inclusion of sdram.h from drivers/ddr/altera/sdram.c
thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Rework remaining two register setting functions such that they only
return the final register value. Move the register setting into the
block of register I/O in sdram_mmr_init_full().
Signed-off-by: Marek Vasut <marex@denx.de>
Merge sdr_set_*() functions which are just setting registers among
the sea of register setting in sdram_mmr_init_full(). There is no
need to keep them separate this way, there is nothing special about
them.
Signed-off-by: Marek Vasut <marex@denx.de>
Suck out all the CONFIG_HPS_SDR_CTRLCFG_* from sdram_mmr_init_full()
into the socfpga_sdram_config structure. There is still one ugly
macro left behind, but this will be taken care of in subsequent patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Zap all the ad-hoc readbacks from the registers and other useless
and broken debug output. This is really not useful and is only
confusing.
Signed-off-by: Marek Vasut <marex@denx.de>
Introduce this seemingly massive structure, which holds required values
of all the registers of the SDRAM controller. The idea here is to avoid
including the sdram.h header file, which is full of ad-hoc macros that
polute the global namespace. Once the cleanup of sdram.c would be complete
and all registers would be loaded from this new socfpga_sdram_config, a
board file will only pass this structure into the sdram.c . This will
hide all the horrors generated by QTS in the board directory.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Merge set_sdr_dram_timing{1,2,3,4,lowpwr}() into single function
set_sdr_dram_timing() , since there's no point in keeping all this
stuff separate anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
The big plan here is to remove all the CONFIG_HPS_SDR_ macros, hide
them in QTS compatibility layer in board implementation and pass only
a small structure into the driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Remove all parameters of this function, since they are only constants
passed in from another function, so make them local. Also, rename the
function to get_errata_rows() as this is closer to what it does.
Signed-off-by: Marek Vasut <marex@denx.de>
This function is implementing the DDR calibration Stage 3 as
described in Altera EMI_RM 2015.05.04 . The main body of this
function is almost identical to Stage 1.3 (DQ/DQS centering)
for all but two flags -- use_read_test and update_fom. Convert
this function to call rw_mgr_mem_calibrate_dq_dqs_centering()
with the correct flags set to trim down the code duplication.
Moreover, reorder the remnants in the function a little and
convert the function to return either 0 or -EIO in case of
success and failure respectively, to match the common return
value convention.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean up coding style, mostly broken multiline formatting strings
in debug output. Also clean up data types and constify where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix data types and constify where applicable, fix broken multiline
debug strings and fix comments. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix the return value of the function to match common convention
where 0 means success and negative means error. Fix the return
values in case of an error to use errno.h codes.
Signed-off-by: Marek Vasut <marex@denx.de>
The read_group and write_group arguments are the same in all
cases when this function is invoked, just merge them into one
rw_group argument. Also, clean up the function argument data
types and constify them.
Signed-off-by: Marek Vasut <marex@denx.de>
The search_stop_check() always resets the bit_chk to a new value,
so bit_chk will never survive between search_left_edge() and
search_right_edge() invocation. There is thus no need to pass
it into these functions, so make bit_chk local to them.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out center_dq_windows(), which is common code between
stage 2 and stage 3 of the calibration again and cater for
the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out the get_window_mid_index() for finding the best DQ
window centering. This is again code common to two stages, so
pull it out.
Signed-off-by: Marek Vasut <marex@denx.de>
First of all, don't break strings in the debug_cond() calls across
multiple lines. Next, zap a couple of really odd casts in the code.
Finally, make i into a signed variable, so it is possible to avoid
constructs of the form:
for (i = FOO;; i--) { <code>; if (i == 0) break; }.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out common code from search_left_edge() and search_right_edge()
which checks whether searching for the window edge should stop. The
code is almost identical, so pull it into separate function and cater
for the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out common code from rw_mgr_mem_calibrate_writes_center()
and rw_mgr_mem_calibrate_vfifo_center() for searching for the
left edge of the window. The code is almost identical, so pull
it into separate function and cater for the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out common code from rw_mgr_mem_calibrate_writes_center()
and rw_mgr_mem_calibrate_vfifo_center() for searching for the
right edge of the window. The code is almost identical, so pull
it into separate function and cater for the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Reorder the content of the function a little and fix the comments
so they at least become full sentences. Constify function args.
Fix the return value to match the common convention of 0 meaning
success.
Signed-off-by: Marek Vasut <marex@denx.de>
The C language has signed types, so make use of them. Fix this
obscene loop, which tries to do away with unsigned type, but
just makes the code more cryptic.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean up the debug output handling at the end of the function
and factor out common function call from the condition.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement common sdr_find_phase_delay() function and convert all
places which use such code to this unified function. No functional
change to the code.
Signed-off-by: Marek Vasut <marex@denx.de>
If d != 0 after sdr_working_phase() finishes, the else branch
of the condition has no impact on anything at all, since work_end
was already set independently of the value of "d" . Zap this
useless code.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix data types, constify where applicable, fix comments and debug
strings. In case enough failing reads are detected, just return
right away instead of breaking from the loop. This lets us make
the error handling at the end much simpler.
Signed-off-by: Marek Vasut <marex@denx.de>
Pluck out all this VFIFO value counting, which turns out to be
completely unused. Thus, remove it to simplify the code.
Signed-off-by: Marek Vasut <marex@denx.de>
The "d" variable is set to 0 in sdr_backup_phase() and is not used
at all in sdr_nonworking_phase(). Make it local and zap it respectively.
Signed-off-by: Marek Vasut <marex@denx.de>
Wrap dtaps_per_ptap into the sdr_working_phase() function to trim
down the number of params. It's a constant too.
Signed-off-by: Marek Vasut <marex@denx.de>
It is now clear that the max_working_cnt variable is totally unused.
Zap the variable and zap other variables which became unused due to
this change too.
Signed-off-by: Marek Vasut <marex@denx.de>
Pull out the loop for eaching working/non-working DQS enable phase
into a separate function, as this is mostly common code between.
Clean up sdr_working_phase() and sdr_nonworking_phase() while switching
these two functions to the common sdr_find_phase().
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of found_{begin,end} variables. Instead of breaking out
through all of the loops, just return when the begin/end of the
window is found and be done with it. Also clean up the trailing
conditional expression, which is now much easier.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix the arguments passed to these functions. The bit_chk is
overriden by rw_mgr_mem_calibrate_read_test_all_ranks() which
is invoked by all three sdr_*_phase() functions, so just make
this into local variable.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix the arguments passed to these functions. The grp argument
does not have to be passed via reference, it's never modified
within either of those functions, so make it into a value.
Signed-off-by: Marek Vasut <marex@denx.de>
Reorder the end of the function a little by moving the conditional
debug output around a little. Rename the function from _centre() to
_center(). Document the function in kerneldoc.
Signed-off-by: Marek Vasut <marex@denx.de>
This function is a treasure trove of ad-hoc iterative
implementations of mathematical functions. Replace all
of those with their non-iterative counterpart.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean up the arguments of this function. Most of the pointers
passed into the function are either not needed at all, or can
be passed as value instead of reference. Also fix the broken
multiline debug strings. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This function is only invoked from rw_mgr_mem_calibrate_dqs_enable_calibration()
and at this point, it is just one level of indirection, so wrap the
rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase_sweep_dq_in_delay() into
rw_mgr_mem_calibrate_dqs_enable_calibration() to get rid of the level
of indirection.
Signed-off-by: Marek Vasut <marex@denx.de>
Replace at least one of the loops in this function with call of a
standard function call instead of the ad-hoc implementation. The
other one cannot be replaced, since the delay is incremented for
each group.
Signed-off-by: Marek Vasut <marex@denx.de>
The read_group and write_group params have the same value for all (one)
invocations of this function, just merge them into a single param.
Signed-off-by: Marek Vasut <marex@denx.de>
Start cleaning up this function. In the first part, just fix
the incorrectly broken debug strings and fix return value to
respect the common convention.
Signed-off-by: Marek Vasut <marex@denx.de>
Rework this function such that the code is more readable. Zap
unused parameter "num_tries" while at it. Also wrap parameter
"bit_chk" into this function as it's value is not used outside.
Finally, fix the return value from this function to match the
common expectation, where 0 means success.
Signed-off-by: Marek Vasut <marex@denx.de>
This function is called from one single place and it's sole purpose
is to call one single function with slightly modified arguments.
Zap this function to skip this useless intermediate step.
Signed-off-by: Marek Vasut <marex@denx.de>
Just extract this piece of functionality into separate function
to make the code better separated. This matches the division in
Altera documentation, Altera EMI_RM 2015.05.04 , section 1, the
UniPHY Calibration Stages.
Signed-off-by: Marek Vasut <marex@denx.de>
Just extract this piece of functionality into separate function
to make the code better separated. This matches the division in
Altera documentation, Altera EMI_RM 2015.05.04 , section 1, the
UniPHY Calibration Stages.
Signed-off-by: Marek Vasut <marex@denx.de>
Just extract this piece of functionality into separate function
to make the code better separated. This matches the division in
Altera documentation, Altera EMI_RM 2015.05.04 , section 1, the
UniPHY Calibration Stages.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
It is clear that the read_group and write_group variables
have the same value, to just make them into one variable
called rw_group. While doing this, constify the variables
as they are constant.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
This patch fixes the broken formatting strings in debug_cond()
invocations.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
This patch cleans up the handling of grp_calibrated such
that the variable isn't used all over the place, but just
very localy. This allows trimming down the indent issues.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
This patch just tweaks the indentation so it is visible
what to do with the grp_calibrated variable.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
This patch just tweaks the indentation so it is visible
what is supposed to go where.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch just adds an expanded documentation header to the
aforementioned function. This is needed to make it easier to
match the purpose of this function with the documentation.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
Rework the code for the the middle-loop of the mega-loop
this time and deal with the group_failed variable. Instead
of checking if the group failed in the previous calibration
part, just jump to the end of the loop if calibration did
fail and increment the counter. This shaves away one more
level of indent while making the code slightly more readable.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
Rework the code for the last loop within the mega-loop
to make it actually readable and not an insane cryptic pile
of indent failure.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
Rework the code for the third loop within the middle-loop
of the mega-loop to make it actually readable and not an
insane cryptic pile of indent failure.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
Rework the code for the second loop within the middle-loop
of the mega-loop to make it actually readable and not an
insane cryptic pile of indent failure.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
Rework the code for the first loop within the middle-loop
of the mega-loop to make it actually readable and not an
insane cryptic pile of indent failure.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Redo the mega-condition such that if the calibration is to be skipped,
the positive branch of the condition does all the work and returns.
The negative branch, which is in fact the default behavior, is then
converted to a code which is no longer conditional. This trims down
the indent by one level.
Signed-off-by: Marek Vasut <marex@denx.de>
Perform minor coding style cleanup of the mem_skip_calibrate() function,
clean up comments and add kerneldoc. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Turn the big inner if (RW_MGR_MEM_NUMBER_OF_RANKS == ...) conditional
into a switch {} statement instead. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
First, invert the logic of the if (odt_mode == ...) conditional to make
the OFF mode harder to miss. It is a short piece of code right at the
end, so move it up.
Also, clean up data types and constify where applicable and clean up
the cs_and_odt_mask assignment. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean mem_config() function. First, reorder the math done in the
function such that WLAT and RLAT computation is together. Then,
scrap contradictory comments which do not match the result of the
math at all. Next, extract the mem_precharge_and_activate() call
from the end of the function as it is completely unrelated here.
Finally, rename the function to mem_init_latency().
Signed-off-by: Marek Vasut <marex@denx.de>
Clean the function up slightly by using clrsetbits_le32() to flip
bits in registers instead of cryptic bitmasks. Zap condition checking
for PHY_DEBUG_IN_DEBUG_MODE flag, which is never set. Split the
calibration report into separate debug_mem_calibrate() function.
Signed-off-by: Marek Vasut <marex@denx.de>
Init both structures with zeroes and zap all those zeroing shenanigans
further down in the sdram_calibration_full().
Signed-off-by: Marek Vasut <marex@denx.de>
Clean the function up by getting rid of all the insane XOR-leftshift
combos when assembling register values. While at it, remove all the
ad-hoc variables necessary for this XOR-leftshift voodoo. Finally,
get rid of the iterative division implementation of two constants
and replace it with a DIV_ROUND_UP() macro :-)
Signed-off-by: Marek Vasut <marex@denx.de>
Contemporary CPUs can perform division just fine, use this
functionality and zap another implementation of iterative
division :-)
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out almost common code from rw_mgr_mem_handoff() and
rw_mgr_mem_initialize() into separate rw_mgr_mem_load_user().
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean the DQS and OCT parts of the function, clean up the chopped
formatting strings in debug_cond() and slightly improve the code.
Zap group_bgn argument as it is used only in debug messages. Document
the function using kerneldoc. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Apparently, in case of the DQ and DM, the value if the new_delay variable
is calculated, but the value is not used. Zap the entire code which does
calculate the value.
It is not clear to me whether or not the code is doing the right thing
in the first place. Right now, it calls scc_mgr_load_dq() and
scc_mgr_load_dm() respectively, but I suspect it might need to call
scc_mgr_apply_group_dq_out1_delay() and scc_mgr_apply_group_dm_out1_delay()
instead. This is something Altera must investigate.
Signed-off-by: Marek Vasut <marex@denx.de>
First, zap unused argument of the function. Next, clean up
the data types, constify where applicable, clean up comments
and add kerneldoc.
Signed-off-by: Marek Vasut <marex@denx.de>
Move scc_mgr_set_hhp_extras() out of scc_set_bypass_mode() as it
has nothing to do in there. Instead, invoke it from mem_calibrate()
just before invoking scc_set_bypass_mode().
Signed-off-by: Marek Vasut <marex@denx.de>
Minor coding style cleanup for this function. Furthermore, move
ad-hoc debug_cond() calls from the only location from where this
function is invoked into this actual function.
Signed-off-by: Marek Vasut <marex@denx.de>
Make this function more readable, no functional change. Also, zap the
forward declaration, which is no longer needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement universal scc_mgr_set_all_ranks() function and convert
various ad-hoc implementations of similar functionality to use
this single function. Document the function in kerneldoc.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement unified scc_mgr_set() function and convert all those
9 scc_mgr_set_*() ad-hoc functions to call this one function.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch just puts functions which look similar next to each
other, so they can be sorted out. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Turn the insides of these functions into trivial clrsetbits_le32()
and fix the data type of their argument to reflect it's actual size.
Signed-off-by: Marek Vasut <marex@denx.de>
Remove the remaining invocations of sdr_get_addr() and the function
itself. This makes the code a bit less cryptic.
Signed-off-by: Marek Vasut <marex@denx.de>
The debug messages missed proper newlines and/or spaces in them.
Fix the formatting.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@konsulko.com>
It is the configuration data that should go into the register,
not the register mask, just like the surrounding code does it.
Fix this typo.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@konsulko.com>
Move the structure prototype from sdram.h header file into sdram.c
source file, since it is used only there and for local purpose only.
There is no point in having it global.
While at this move, fix the data types in the structure from uintNN_t
to uNN and fix the coding style a bit.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch enables the SDRAM controller that is used on Altera's SoCFPGA
family. This patch configures the SDRAM controller based on a configuration
file that is generated from the Quartus tool, sdram_config.h.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
By default the bstopre value has been set to 0x100, used to be 1/4
value of refint. Modern DDR has increased the refresh time. Adjust
to 1/4 of refresh interval dynamically. Individual board can still
override this value in board ddr file, or to use auto-precharge.
Signed-off-by: York Sun <yorksun@freescale.com>
This patch adds the DDR3 setup and training code taken from the Marvell
U-Boot repository. This code used to be included as a binary (bin_hdr)
into the Armada A38x boot image. Not linked with the main U-Boot. With this
code addition and the serdes/PHY setup code, the Armada A38x support
in mainline U-Boot is finally self-contained. So the complete image
for booting can be built from mainline U-Boot. Without any additional
external inclusion.
Note:
This code has undergone many hours (days!) of coding-style cleanup and
refactoring. It still is not checkpatch clean though, I'm afraid. As the
factoring of the code has so many levels of indentation that many lines
are longer than 80 chars.
Signed-off-by: Stefan Roese <sr@denx.de>
With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to introduce a new
directory infrastructure. To support multiple Marvell DDR controller.
This will be the new structure:
drivers/ddr/marvell/axp
Supporting Armada XP (AXP) devices (and perhaps Armada 370)
drivers/ddr/marvell/a38x
Supporting Armada 38x devices (and perhaps Armada 39x)
Signed-off-by: Stefan Roese <sr@denx.de>
In case SPD address changes between board revisions, updating SPD
address can be called from board file.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
The macro to select the I2C address for ECC bus-width detection
was defined incorrectly for the Marvell DB-MV784MP-GP board. This
patch changes the macro to the correct value to fix this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This erratum only applies to general purpose DDR controllers in LS2.
It shouldn't be applied to DP-DDR controller. Check DDRC versoin number
before applying workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
Add built-in memory test to catch errors after DDR is initialized, before
any other transactions. To enable this test, define CONFIG_FSL_DDR_BIST.
An environmental variable "ddr_bist" is checked before starting test.
It takes a while (several seconds) depending on system memory size.
Signed-off-by: York Sun <yorksun@freescale.com>
CS0 was not allowed to be empty by u-boot driver in the past to simplify
the driver. This may be inconvenient for some debugging. This patch lifts
the restrictions. Controller interleaving still requires CS0 populated.
Signed-off-by: York Sun <yorksun@freescale.com>
Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.
Signed-off-by: York Sun <yorksun@freescale.com>
According to the MPC8555/MPC8541 reference manual the SS_EN (source
synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set
during initialization.
>From section 9.4.1.8 of that manual:
Source synchronous enable. This bit field must be set during
initialization. See Section 9.6.1, "DDR SDRAM Initialization
Sequence," details.
0 - Reserved
1 - The address and command are sent to the DDR SDRAMs source
synchronously.
In addition, Freescale application note AN2805 is also very clear that
this bit must be set.
This patch reverts a change introduced by commit
457caecdbc.
Testing Done:
Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS
and inspected the generated assembly code to verify the SS_EN bit was being
set. There is one extra instruction emitted:
fff9b774: 65 29 80 00 oris r9,r9,32768
Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no
additional instructions were emitted related to this patch.
Booted an image on a MPC8541 based board successfully.
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add sync of refresh for multiple DDR controllers. DDRC initialization
needs to complete first. Code is re-ordered to keep refresh close.
Signed-off-by: York Sun <yorksun@freescale.com>
Controller number is passed for function calls to support individual
DDR clock, depending on SoC implementation. It is backward compatible
with exising platforms. Multiple clocks have been verifyed on LS2085A
emulator.
Signed-off-by: York Sun <yorksun@freescale.com>
On ZeBu emulator, CAS to preamble overrides need to be set to
satisfy the timing. This only impact platforms with CONFIG_EMU.
These should be set before MEM_EN is set.
Signed-off-by: York Sun <yorksun@freescale.com>
This patch adds the DDR3 setup and training code taken from the Marvell
U-Boot repository. This code used to be included as a binary (bin_hdr)
into the AXP boot image. Not linked with the main U-Boot. With this code
addition and the following serdes/PHY setup code, the Armada-XP support
in mainline U-Boot is finally self-contained. So the complete image
for booting can be built from mainline U-Boot. Without any additional
external inclusion. Hopefully other MVEBU SoC's will follow here.
Support for some SoC's has been removed in this version. This is:
MV_MSYS:
The code referred to by the MV_MSYS define is currently unused. And its
not really planned to support this in mainline. So lets remove it to
make the code clearer and increase the readability.
MV88F68XX (A38x):
The code referred to by the MV88F68XX define (A38x) is currently unused.
And its partial and not sufficient for this device in this stage.
So lets remove it to make the code clearer and increase the readability.
MV88F66XX (ALP):
The code referred to by the MV88F66XX define is currently unused. And its
not really planned to support this in mainline. So lets remove it to
make the code clearer and increase the readability.
MV88F78X60_Z1:
The code referred to by the MV88F78X60_Z1 define is currently unused. As the
Z1 revision of the AXP is not supported in mainline anymore.
So lets remove it to make the code clearer and increase the readability.
Remove support for Z1 & A0 AXP revisions (steppings). The current stepping
is B0 and this is the only one that is actively supported in this code
version.
Tested on AXP using a SPD DIMM setup on the Marvell DB-MV784MP-GP board and
on a custom fixed DDR configuration board (maxbcm).
Note:
This code has undergone many hours of coding-style cleanup and refactoring.
It still is not checkpatch clean though, I'm afraid. As the factoring of the
code has so many levels of indentation that many lines are longer than 80
chars. This might be some task to tackly later on.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
Internal memory controller counters can reach a bad state after
training in DDR4 mode if accumulated ECC or DBI mode is eanbled.
Signed-off-by: York Sun <yorksun@freescale.com>
For DDR controller version 4.7 or newer, MRC_CYC (mode register set
cycle time) is max(tMRD, tMOD). tMRD is 4nCK, or 8nCK (RDIMM). tMOD
is max(12nCK, 15ns) according to JEDEC spec.
DDR4 is not affected by this change.
Signed-off-by: York Sun <yorksun@freescale.com>
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Some UDIMMs have faulty SPD with wrong mapping for DQ[36-39].
Using raw card spec in case this error is detected.
Signed-off-by: York Sun <yorksun@freescale.com>
Increase write-to-write and read-to-read turnaround time for two-slot DDR
configurations. Previously only quad-rank and two dual-rank configurations
have this additional turnaround time. A recent test on two single-rank
DIMMs shows the shorter additional turnaround time is also needed.
Signed-off-by: York Sun <yorksun@freescale.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
When accumulated ECC is enabled, the DQ_MAP for ECC[4:7] needs to be set
to 0, i.e. 0->0, 1->1, etc., required by controller logic, even these pins
are not actually connected.
Also fix a bug when reading from DDR register to use proper accessor for
correct endianess.
Signed-off-by: York Sun <yorksun@freescale.com>
The driver was written using old DDR3 spec which only covers low speeds.
The value would be suboptimal for higher speeds. Fix both timing according
to latest DDR3 spec, remove tCKE as an config option.
Signed-off-by: York Sun <yorksun@freescale.com>
U-boot has been initializing DDR for the main memory. The presumption
is the memory stays as a big continuous block, either linear or
interleaved. This change is to support putting some DDR controllers
to separated space without counting into main memory. The standalone
memory controller could use different number of DIMM slots.
Signed-off-by: York Sun <yorksun@freescale.com>
JEDEC spec allows DRAM vendors to use prime DQ for write leveling. This
is not an issue unless some DQ pins are not connected. If a platform uses
regular DIMMs but with reduced DDR ECC pins, the prime DQ may end up on
those floating pins for the second rank. The workaround is to use a known
good chip select for this purpose.
Signed-off-by: York Sun <yorksun@freescale.com>
Reading DDR register should use ddr_in32() for proper endianess.
This patch fixes incorrect waiting time for ARM platforms.
Signed-off-by: York Sun <yorksun@freescale.com>
If less than 8 ECC pins are used for DDR data bus width smaller than 64
bits, the 8-bit ECC code will be transmitted/received across several beats,
and it will be used to check 64-bits of data once 8-bits of ECC are
accumulated.
Signed-off-by: York Sun <yorksun@freescale.com>
The field wrtord_bg should add 2 clocks if on the fly chop is enabled,
according to DDR controller manual for DDR4.
Signed-off-by: York Sun <yorksun@freescale.com>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.
Signed-off-by: York Sun <yorksun@freescale.com>
When T104x soc wakes up from deep sleep, control is passed to the
primary core that starts executing uboot. After re-initialized some
IP blocks, like DDRC, kernel will take responsibility to continue
to restore environment it leaves before.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This is a theoretical possible out of bounds error in DDR driver. Adding
check before using array index. Also change some runtime conditions to
pre-compiling conditions.
Signed-off-by: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale LayerScape SoCs support controller interleaving on 256 byte size.
This interleaving is mandoratory.
Signed-off-by: York Sun <yorksun@freescale.com>
DDR base address has been the same from the view of core and DDR
controllers. This has changed for Freescale ARM-based SoCs. Controllers
setup DDR memory in a contiguous space and cores view it at separated
locations.
Signed-off-by: York Sun <yorksun@freescale.com>
Initially it was believed the DDR controller on Freescale ARM would have
big endian. But some platform will have little endian.
Signed-off-by: York Sun <yorksun@freescale.com>
Existing workaround only handles one RDIMM on reference design. In case
of two RDIMMs being used, the workaround requires two separate writes to
DDR_SDRAM_MD_CNTL register.
This patch also restores two debug registers changed by the workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Ben Collins <ben.c@servergy.com>
CC: James Yang <James.Yang@freescale.com>
The DRAM base has been zero for Power SoCs. It could be non-zero
for ARM SoCs. Use a macro instead of hard-coding to zero.
Signed-off-by: York Sun <yorksun@freescale.com>
Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.
TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit c360ceac.
Signed-off-by: York Sun <yorksun@freescale.com>
Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
