U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
When accumulated ECC is enabled, the DQ_MAP for ECC[4:7] needs to be set
to 0, i.e. 0->0, 1->1, etc., required by controller logic, even these pins
are not actually connected.
Also fix a bug when reading from DDR register to use proper accessor for
correct endianess.
Signed-off-by: York Sun <yorksun@freescale.com>
The driver was written using old DDR3 spec which only covers low speeds.
The value would be suboptimal for higher speeds. Fix both timing according
to latest DDR3 spec, remove tCKE as an config option.
Signed-off-by: York Sun <yorksun@freescale.com>
U-boot has been initializing DDR for the main memory. The presumption
is the memory stays as a big continuous block, either linear or
interleaved. This change is to support putting some DDR controllers
to separated space without counting into main memory. The standalone
memory controller could use different number of DIMM slots.
Signed-off-by: York Sun <yorksun@freescale.com>
JEDEC spec allows DRAM vendors to use prime DQ for write leveling. This
is not an issue unless some DQ pins are not connected. If a platform uses
regular DIMMs but with reduced DDR ECC pins, the prime DQ may end up on
those floating pins for the second rank. The workaround is to use a known
good chip select for this purpose.
Signed-off-by: York Sun <yorksun@freescale.com>
Reading DDR register should use ddr_in32() for proper endianess.
This patch fixes incorrect waiting time for ARM platforms.
Signed-off-by: York Sun <yorksun@freescale.com>
If less than 8 ECC pins are used for DDR data bus width smaller than 64
bits, the 8-bit ECC code will be transmitted/received across several beats,
and it will be used to check 64-bits of data once 8-bits of ECC are
accumulated.
Signed-off-by: York Sun <yorksun@freescale.com>
The field wrtord_bg should add 2 clocks if on the fly chop is enabled,
according to DDR controller manual for DDR4.
Signed-off-by: York Sun <yorksun@freescale.com>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.
Signed-off-by: York Sun <yorksun@freescale.com>
When T104x soc wakes up from deep sleep, control is passed to the
primary core that starts executing uboot. After re-initialized some
IP blocks, like DDRC, kernel will take responsibility to continue
to restore environment it leaves before.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This is a theoretical possible out of bounds error in DDR driver. Adding
check before using array index. Also change some runtime conditions to
pre-compiling conditions.
Signed-off-by: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale LayerScape SoCs support controller interleaving on 256 byte size.
This interleaving is mandoratory.
Signed-off-by: York Sun <yorksun@freescale.com>
DDR base address has been the same from the view of core and DDR
controllers. This has changed for Freescale ARM-based SoCs. Controllers
setup DDR memory in a contiguous space and cores view it at separated
locations.
Signed-off-by: York Sun <yorksun@freescale.com>
Initially it was believed the DDR controller on Freescale ARM would have
big endian. But some platform will have little endian.
Signed-off-by: York Sun <yorksun@freescale.com>
Existing workaround only handles one RDIMM on reference design. In case
of two RDIMMs being used, the workaround requires two separate writes to
DDR_SDRAM_MD_CNTL register.
This patch also restores two debug registers changed by the workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Ben Collins <ben.c@servergy.com>
CC: James Yang <James.Yang@freescale.com>
The DRAM base has been zero for Power SoCs. It could be non-zero
for ARM SoCs. Use a macro instead of hard-coding to zero.
Signed-off-by: York Sun <yorksun@freescale.com>
Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.
TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit c360ceac.
Signed-off-by: York Sun <yorksun@freescale.com>
Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
