Till now the UTL registers on 405EX were not initialized but left with
their default values. This patch new initializes some of the UTL
registers on 405EX.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds changes needed for Makalu rev 1.1:
- Enable 2nd DDR2 bank resulting in 256MByte of SDRAM
- Enable 2nd ethernet port EMAC1
- Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE)
- Reset PCIe ports via GPIO upon bootup
Signed-off-by: Stefan Roese <sr@denx.de>
- Rename CFG_440_GPIO_TABLE to CFG_4xx_GPIO_TABLE
- Cleanup of the 4xx GPIO functions
- Move some GPIO defines from the cpu headers ppc405.h/ppc440.h into gpio.h
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for three new DDR chips that may be present on a NG
INKA4x0 hardware: HYB25D512160BF-5, K4H511638C-7CB3, T46V32M16BN-6IT.
Cleanup board/inka4x0/mt48lc16m16a2-75.h file.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
This patch makes the sequoia board use the generic usb-ohci driver
instead of cpu/ppc4xx/usb_ohci.c.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add cfb console support to FSL 8610 DIU driver.
Inspect board version from PIXIS to obtain correct pixel format.
Use #define CONFIG_VIDEO in config file to enable fb console.
To switch monitor, set monitor variable to
0 - DVI, 1 - Single link LVDS, 2 - Double link LVDS
followed by "diufb init".
Preserve logo bitmap at the top of the fb console.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
1280x1024 and 1024x768 @ 32 bpp are supported now.
DVI, Single-link LVDS, Double-link LVDS are all supported.
Environmental variable "monitor" is used to specify monitor port.
A new command "diufb" is introduced to reinitialize monitor
and display a BMP file in the memory. So far, 1-bit, 4-bit,
8-bit and 24-bit BMP formats are supported.
diufb init
- initialize the diu driver
Enable the port specified in the environmental variable "monitor"
diufb addr
- display bmp file in memory.
The bmp image should be no bigger than the resolution, 1280x1024
for DVI and double-link LVDS, 1024x768 for single-link LVDS.
Note, this driver allocate memory but doesn't free it after use
It is written on purpose -- to avoid a failure of reallocation
due to memory fragement.
ECC of DDR is disabled for DIU performance. L2 data cache is also disabled.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon loeliger <jdl@freescale.com>
The address in the BAT register is aligned with the BAT size.
The original definition actually did not define BAT for PCIE2 IO.
This patch fix this.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Basically, refactor the CFG_PIXIS_VBOOT_MASK values
into the separate board config files.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch adds support for 1000BASE-X to functions "miiphy_speed ()" and
"miiphy_duplex()". It also adds function "miiphy_is_1000base_x ()", which
returns non-zero iff the PHY registers are configured for 1000BASE-X. The
"mii info" command is modified to distinguish between 1000BASE-T and -X.
Signed-off-by: Larry Johnson <lrj@acm.org>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
The configuration file has already enabled USB, but it
missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB
on MPC8641HPCN can not work because of the wrong USB
register endian.
And add the USB command to U-Boot commands list.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
To get the IDS8247 board working following are done:
- FCC2 is deactivated
- FCC1 is activated
- I2C is activated
- CFI driver is activated
- Adapted for use with LIBFDT
Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
--
This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang is right: It's not a good idea to set up default initial
ethernet addresses for a board, even though they belong to the local
range.
This will change the failure mode from "IT manager screams at you for
using duplicate ethernet addresses" to a nice error message explaining
that the ethernet address hasn't been set properly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
We now use a value in the gd (global data) structure for the UART input
frequency, since the PPC4xx_SYS_INFO struct is always rewritten completely
in get_sys_info().
Signed-off-by: Stefan Roese <sr@denx.de>
The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the Xicor/Intersil X1205 RTC used on the
AMCC Makalu eval board. This driver is basically cloned from the Linux
driver version (2.6.23).
This patch also introduces the Linux bcd.h header for the BCD2BIN/
BIN2BCD conversions. In the future some of the other U-Boot RTC driver
should be converted to also use this header instead of implementing
their own local copy of these functions/macros.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some common 4xx macros and the PPC405_SYS_INFO/
PPC440_SYS_INFO structure into the common ppc4xx.h header.
Lot's of other macros are good candidates to be consolidated this way
in the future.
Signed-off-by: Stefan Roese <sr@denx.de>
CONFIG_BOOKE must be defined for PPC440 processors so that the proper SPR
number is used to access system registers.
Signed-off-by: Eugene O'Brien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
On Yucca & Katmai, the inbound memory map pointed to 0x4.0000.0000, which
is the internal SRAM. Since I now ported and tested this endpoint mode
on Kilauea successfully to map to 0 (SDRAM), I also changed this for
Katmai.
Yucca will stay at internal SRAM for now. Not sure if somebody relies on
this setup.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds endpoint support for the AMCC Kilauea eval board. It can
be tested by connecting a reworked PCIe cable (only 1x lane singles
connected) to another root-complex.
In this test setup, a 64MB inbound window is configured at BAR0 which maps
to 0 on the PLB side. So accessing this BAR0 from the root-complex will
access the first 64MB of the SDRAM on the PPC side.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for dynamic configuration of PCIe ports for the
AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe
boards Yucca & Katmai and the 405EX board Kilauea.
This dynamic configuration is done via the "pcie_mode" environement
variable. This variable can be set to "EP" or "RP" for endpoint or
rootpoint mode. Multiple values can be joined via the ":" delimiter.
Here an example:
pcie_mode=RP:EP:EP
This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2
as endpoint.
Per default Yucca will be configured as:
pcie_mode=RP:EP:EP
Per default Katmai will be configured as:
pcie_mode=RP:RP:REP
Per default Kilauea will be configured as:
pcie_mode=RP:RP
Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the fdt support on the AMCC Kilauea eval board.
Additionally now EBC ranges fdt fixup is included to support NOR
FLASH mapping via the Linux physmap_of driver.
This Kilauea port now support booting arch/ppc and arch/powerpc
Linux kernels. The default environment "net_nfs" is for arch/ppc
and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc
support will be removed.
Signed-off-by: Stefan Roese <sr@denx.de>
128MB seems to be the smallest possible value for the memory size
for on PCIe port. With this change now the BAR's of the PCIe cards
are accessible under U-Boot.
One big note: This only works for PCIe port 0 & 1. For port 2 this
currently doesn't work, since the base address is now 0xc0000000
(0xb0000000 + 2 * 0x08000000), and this is already occupied by
CFG_PCIE0_CFGBASE. But solving this issue for port 2 would mean
to change the base addresses completely and this change would have
too much impact right now.
This patch adds debug output to the 4xx pcie driver too.
Signed-off-by: Stefan Roese <sr@denx.de>
These files were introduced with the IBM 405GP but are currently used on all
4xx PPC platforms. So the name doesn't match the content anymore. This patch
renames the files to 4xx_pci.c/h.
Signed-off-by: Stefan Roese <sr@denx.de>
(3) This patch introduces macros like SDRN_PESDR_DLPSET(port) to access
the SDR registers of the PCIe ports. This makes the overall design
clearer, since it removed a lot of switch statements which are not
needed anymore.
Also, the functions ppc4xx_init_pcie_rootport() and
ppc4xx_init_pcie_entport() are merged into a single function
ppc4xx_init_pcie_port(), since most of the code was duplicated.
This makes maintainance and porting to other 4xx platforms
easier.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is the first patch of a series to make the 440SPe PCIe code
usable on different 4xx PPC platforms. In preperation for the new 405EX
which is also equipped with PCIe interfaces.
(2) This patch renames the functions from 440spe_ to 4xx_ with a
little additional cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is the first patch of a series to make the 440SPe PCIe code
usable on different 4xx PPC platforms. In preperation for the new 405EX
which is also equipped with PCIe interfaces.
(1) This patch renames the files from 440spe_pcie to 4xx_pcie
Signed-off-by: Stefan Roese <sr@denx.de>
With this patch PSC3 is configured as UART. This is done, because if
the pins of PSC3 are not configured at all (-> all pins are GPI),
due to crosstalk, spurious characters may be send over the RX232_2_TXD
signal line.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With this patch PSC3 is configured as UART. This is done, because if
the pins of PSC3 are not configured at all (-> all pins are GPI),
due to crosstalk, spurious characters may be send over the RX232_2_TXD
signal line.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
The pxa255_idp being an old unmaintained board showed several issues:
1. CONFIG_INIT_CRITICAL was still defined.
2. Neither CONFIG_MAC_PARTITION nor CONFIG_DOS_PARTITION was defined.
3. Symbol flash_addr was undeclared.
4. The boards lowlevel_init function was still called memsetup.
5. The TEXT_BASE was still 0xa3000000 rather than 0xa3080000.
6. Using -march=armv5 instead of -march=armv5te resulted in lots of
'target CPU does not support interworking' warnings on recent compilers.
7. The PXA's serial driver redefined FFUART, BTUART and STUART used as
indexes rather than the register definitions from the pxa-regs header
file. Renamed them to FFUART_INDEX, BTUART_INDEX and STUART_INDEX to
avoid any ambiguities.
8. There were several redefinition warnings concerning ICMR, OSMR3,
OSCR, OWER, OIER, RCSR and CCCR in the PXA's assembly start file.
9. The board configuration file was rather outdated.
10. The part header file defined the vendor, product and revision arrays
as unsigned chars instead of just chars in the block_dev_desc_t
structure.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
New board has faster oscillator and a different Flash chip. This affects:
- CFG_MPC5XXX_CLKIN
- SDRAM timings
- Flash CS configuration (timings)
- Flash sector size, and thus MTD partition layout
- malloc() arena size (due to bigger Flash sectors)
- smaller memory test range (due to bigger malloc() arena)
This patch also enables more extensive memory testing via "mtest".
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
PHYSADDR is for physical address, KSEG1ADDR is for uncached.
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
On the MPC85xx CDS we have two issues:
1. The device tree fixup code did not check to see if the property we are
trying to update is actually found. Its possible that it would update
random memory starting at 0.
2. Newer Linux kernel's have moved the location of the PCI nodes to be
sibilings of the soc node and not children. The explicit PATH to the PCI
node would not be found for these device trees. Add the ability to handle
both paths. In the future we shouldn't handle such fixups by explicit path.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the MPC8568 MDS we use ttyS0, UART0, etc. as the standard configured
console. Make it so we match that config what we tell Linux as the early
STDOUT console.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The BCSR status bit for the 66MHz PCI operation was correctly
addressed (MSB/LSB problem). Now the correct currently setup
PCI frequency is displayed upon bootup.
This patch also fixes this problem on Rainier & Yellowstone, since these
boards use the same souce code as Sequoia & Yosemite do.
Signed-off-by: Stefan Roese <sr@denx.de>
At 133 MHz the current SDRAM refresh rate is too fast
(measured 4 * 1.17 us).
CFG_MAMR_PTA changes from 39 to 97. This result
in a refresh rate of 4 * 7.8 us at the default clock
50 MHz. At 133 MHz the value will be then 4 * 2.9 us.
This is a compromise until a new method is found to
adjust the refresh rate.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
CFG_MEMTEST_START uses weird magic involving gd, which fails to
compile. Use hardcoded values instead (we actually know how much RAM
we have on board.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
/bin/bash and /bin/dash (which /bin/sh is linked to on ubuntu) handle embedded
nulls in a string differently. For example, the following statement:
echo "this is a string\0" > afile
Will produce the following with /bin/bash:
"this is a string\0"
But with /bin/dash, will produce:
"this is a string
Bug fixed by moving the embedded null out of the makefile and into the
config header. Also renamed the macro to avoid usage colision with the same
macro used by other board ports.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Updates to atstk1002 U-Boot header file:
- Changed bootargs:
* Set the bootargs for at1002 to point to the SD-card partition instead
* ... of the boot flash.
* Removing the rootfstype since that argument are not needed.
Signed-off-by: Eirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch applies some clarifying comments to how the different
clocks are setup according to atstk1002.h Some of the previous
comments where stating wrongful information.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
With recent toolchains, the environment sectors were no longer aligned to
sector boundaries. The reason was a combination of two bugs:
1) common/environment.c assumed that CONFIG_TQM8xxL would be defined
for all TQM8xxL and TQM8xxM boards. But "include/common.h", where
this gets defined, is not included here (and cannot be included
without causing lots of problems).
Added a new #define CFG_USE_PPCENV for all boards which really
want to put the environment is a ".ppcenv" section.
2) The linker scripts just include environment.o, silently assuming
that the objects in that file are really in the order in which
they are coded in the C file, i. e. "environment" first, then
"redundand_environment", and "env_size" last. However, current
toolchains (GCC-4.x) reorder the objects, causing the environment
data not to start on a flash sector boundary:
Instead of: we got:
40008000 T environment 40008000 T env_size
4000c000 T redundand_environment 40008004 T redundand_environment
40010000 T env_size 4000c004 T environment
Note: this patch fixes just the first part, and cures the alignment
problem by making sure that "env_size" gets placed correctly. However,
we still have a potential issue because primary and redundant
environment sectors are actually swapped, i. e. we have now:
40008000 T redundand_environment
4000c000 T environment
40010000 T env_size
This shall be fixed in the next version.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This config option sets the default for the progress information
output behavior that can also be configured through the 'quiet'
environment variable.
The legacy NAND code does not print the current progress info
on the console. So this option is for backward compatibility for
units that are in the field and where setting the quiet variable
is not an option. With CFG_NAND_QUIET set to '1' the console
progress info is turned off. This can still be overwritten
through the environment variable.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
- update default definitions of kernel_addr and fdt_addr env. variables
- make arch/powerpc booting the default scenario
- update MTD partition layout to match the above
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
- 'pciconfighost' is set by default in order to be able to scan bridges
behind the primary host/PCIe
- 'pciscandelay' env variable is recognized to allow for user-controlled
delay before the PCIe bus enumeration; some peripheral devices require a
significant delay before they can be scanned (e.g. LSI8408E); without the
delay they are not detected
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
- correct configuration space mapping
- correct bus numbering
- better access to config space
Prior to this patch, the 440SPe host/PCIe bridge was able to configure only the
first device on the first bus. We now allow to configure up to 16 buses;
also, scanning for devices behind the PCIe-PCIe bridge is supported, so
peripheral devices farther in hierarchy can be identified.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
This patch adds support for multiple serial ports to the PXA target.
FFUART, BTUART and STUART are supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stop using inline string functions on MIPS as other ARCHs do so,
since the optimized inline asm versions are not small.
This change is triggered by a following MIPS build error:
common/libcommon.a(exports.o)(.text+0xdc): In function `jumptable_init':
common/exports.c:32: undefined reference to `strcmp'
make: *** [u-boot] Error 1
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
This patches contains several bugfixes and cleanups in the latest upstream:
- Don't include linux/config.h
- Remove buggy inline version of memscan.
- Merge with Linux 2.6.11-rc3.
- Fix undefined reference to strcpy in binfmt_misc caused by gcc 3.4.
- Goodbye mips64. 31704 lines of code bite the dust.
- Replace extern inline with static inline.
- Fix return value of strncpy.
- Remove a bunch more "$1" clobbers.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Affects boards: icecube (lite5200), jupiter, motionpro, tqm5200
Tested on: lite5200b
Note: the fixup functions have not been moved to a common place. This
patch is targeted for immediate merging as in solves a build issue, but
the final name/location of the fixups is still subject to debate. I
propose to merge this now, and move the fixups in the next merge window
to be usable by all targets.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The RTC on the M1575 ULI chipset requires a dummy read before
we are able to talk to the RTC. We accomplish this by adding a
second memory region to the PHB the ULI is on and read from it.
The second region is added to maintain compatiabilty with Linux's
view of the PCI memory map.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The 440EPx has a problem when the PCI_CACHE_LINE_SIZE register is
set to non-zero, because it doesn't support MRM (memory-read-
multiple) correctly. We now added the possibility to configure
this register in the board config file, so that the default value
of 8 can be overridden.
Here the details of this patch:
o drivers_pci_auto.c: introduce CFG_PCI_CACHE_LINE_SIZE to allow
board-specific settings. As an example the sequoia board requires 0.
Idea from Stefan Roese <sr@denx.de>.
o board/amcc/sequoia/init.S: add a TLB mapping at 0xE8000000 for the
PCI IO-space. Obtained from Stefan Roese <sr@denx.de>.
o include/configs/sequoia.h: turn CONFIG_PCI_PNP back on and set
CFG_PCI_CACHE_LINE_SIZE to 0.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The Linux PCF8563 RTC driver doesn't do autoprobing, so we need
to supply the RTC I2C address as bootline parameter. This patch
adds support for this rtc probing parameter to the bootargs:
"rtc-pcf8563.probe=0,0x51"
Signed-off-by: Stefan Roese <sr@denx.de>
this had slipped through the cracks, since the sbc board was added
after I wrote the original patch to remove all these symbols, and
before it was merged.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Restore CONFIG_EXTRA_ENV_SETTINGS definition which contains the
correct consoledev needed for linux boot.
Standardize on fdt{file,addr} var to hold dtb file name.
Set PCI inbound memory region from CFG_MEMORY_{BUS,PHYS}.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
if a board/$(VENDOR)/common/Makefile exists, build it.
also add the first such case, board/freescale/common/Makefile, to
handle building board-shared EEPROM, PIXIS, and MDS-PIB code, as
dictated by board configuration.
thusly get rid of alternate build dir errors such as:
FATAL: can't create /work/wd/tmp/u-boot-ppc/board/freescale/mpc8360emds/../common/pq-mds-pib.o: No such file or directory
by putting the common/ mkdir command in its proper place (the common
Makefile). Common bits from existing individual board Makefiles have
been removed.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixes the "type qualifiers ignored on fuction return tpye"
warning for include/s3c2410.h
Signed-off-by: Martin Krause <martin.krause@tqs.de>
define there own I/O functions.
(Needed for the pcs440ep board).
- The default I/O Functions are again 8 Bit accesses.
- Added CONFIG_CMD_IDE for the pcs440ep Board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Since this RTC POST test is taking quite a while to complete
it's only initiated upon special keypress same as the complete
memory POST.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the 2nd EEPROM (AT24C128) on the lwmon5
board. Now the "eeprom" command can be used to read/write from/to this
device. Additionally a new command was added "eepromwp" to en-/disable
the write-protect of this 2nd EEPROM.
The 1st EEPROM is not affected by this write-protect command.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the matrix keyboard on the lwmon5 board.
Since the implementation in the dsPCI is kind of compatible with the
"old" lwmon board, most of the code is copied from the lwmon
board directory.
Signed-off-by: Stefan Roese <sr@denx.de>
platforms wishing to display RAM diagnostics in addition to size,
can do so, on one line, in their own board_add_ram_info()
implementation.
this consequently eliminates CONFIG_ADD_RAM_INFO.
Thanks to Stefan for the hint.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
add board_add_ram_info, to make memory diagnostic output more
consistent. u-boot banner output now looks like:
DRAM: 256 MB (DDR1, 64-bit, ECC on)
and for boards with SDRAM on the local bus, a line such as this is
added:
SDRAM: 64 MB (local bus)
also replaced some magic numbers with their equivalent define names.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The patch split the PIB init code from pci.c to a single file board/freescale/common/pq-mds-pib.c
And add Qoc3 ATM card support for MPC8360EMDS and MPC832XEMDS board.
Signed-off-by Tony Li <tony.li@freescale.com>
The 85xx code now relies on CONFIG_HAS_ETH0 to determine whether
to update TSEC1's device-tree node, so we need to add it
to all the boards with TSECs. Do this for 83xx and 86xx, too,
since they will eventually do something similar.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The PCIe bus that the ULI M1575 is connected to has no possible way of
needing more than the fixed amount of IO & Memory space needed by the ULI.
So make it use far less IO & memory space and have it use the shared LAW. This
free's up a LAW for PCIe1 IO space. Also reduce the amount of IO space needed
by each bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It looks like we had a merge issue that duplicated a bit of code
in ft_board_setup. Also, we need to set CONFIG_HAS_ETH0 to get
the MAC address properly set in the device tree on boot for TSEC1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Actually, fixed a large bug in the UEC for *all* platforms.
How did this ever work?
uec_init() did not follow the spec for eth_init(), and returned
0 on success. Switch it to return the link like tsec_init()
(and 0 on error)
The immap for the 8568 was defined based on MPC8568, rather than
CONFIG_MPC8568
CONFIG_QE was off
CONFIG_ETHPRIME was set to "Freescale GETH". Now is "FSL UEC0"
Fixed a comment about the ranges for CONFIG_ETHPRIME if TSEC_ENET is
enabled
Signed-off-by: Andy Fleming <afleming@freescale.com>
The tsec_info structure and array has a "flags" field for each
ethernet controller. This field is the only reason there are
settings. Switch to defining TSECn_FLAGS for each controller
in the config header, and we can greatly simplify the array, and
also simplify the addition of future boards.
Signed-off-by: Andy Fleming <afleming@freescale.com>
this enables libfdt code by default for the
freescale mpc8313erdb, mpc832xemds, mpc8349emds,
mpc8349itx and gp boards.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Merge to two at45.c files into a common file, split to at45.c and spi.c
Fix spelling error in DM9161 PHY Support.
Initialize at91rm9200 board (and set LED).
Add PIO control for at91rm9200dk LEDs and Mux.
Change dataflash partition boundaries to be compatible with Linux 2.6.
Signed-off-by: Peter Pearse <peter.pearse@arm.com>
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
The PCI ID select values on the Arcadia main board differ depending
on the version of the hardware. The standard configuration supports
Rev 3.1. The legacy target supports Rev 2.x.
Signed-off-by Randy Vinson <rvinson@mvista.com>
This patch is against u-boot-mpc85xx.git of www.denx.com
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
Some patches had inserted warnings into the build:
* mpc8560ads declared data without using it
* cpu_init declared ecm and immap without using it in all CONFIGs
* MPC8548CDS.h had its default filenames changed so that they contained
"\m" in the paths. Made the defaults not Windows-specific (or
anything-specific)
Signed-off-by: Andy Fleming <afleming@freescale.com>
Make the early L1 cache stack region guarded to prevent speculative
fetches outside the locked range.
Use _PHYS defines, not _MEM for cpu-side PCI memory mapped regions.
init.S whitespace cleanup.
Allow TEXT_BASE value to be specified on command line. This allows it
to be set to 0xfffc0000 which cuts the uboot binary in half.
Clear and enable lbc and ecm errors.
Update last_busno in device-tree for pci and pcie.
Remove load of obsolete cpu/mpc85xx/pci.0
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
PCI1 LAW mapping should use CFG_PCI1_MEM_PHY and not _BASE address.
Enable LBC and ECM errors and clear error registers.
Add tftpflash env var to get uboot from tftp server and flash it.
Add pci/pcie convenience env vars to display register space:
"run pcie3regs" to see all pcie3 ccsr registers
"run pcie3cfg" to see all cfg registers
Whitespace cleanup and MPC8544DS.h
Enable CONFIG_INTERRUPTS.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
